| Age | Commit message (Collapse) | Author |
|---|
|
Jana Iyengar found an interesting issue on CUBIC :
The epoch is only updated/reset initially and when experiencing losses.
The delta "t" of now - epoch_start can be arbitrary large after app idle
as well as the bic_target. Consequentially the slope (inverse of
ca->cnt) would be really large, and eventually ca->cnt would be
lower-bounded in the end to 2 to have delayed-ACK slow-start behavior.
This particularly shows up when slow_start_after_idle is disabled
as a dangerous cwnd inflation (1.5 x RTT) after few seconds of idle
time.
Jana initial fix was to reset epoch_start if app limited,
but Neal pointed out it would ask the CUBIC algorithm to recalculate the
curve so that we again start growing steeply upward from where cwnd is
now (as CUBIC does just after a loss). Ideally we'd want the cwnd growth
curve to be the same shape, just shifted later in time by the amount of
the idle period.
Reported-by: Jana Iyengar <jri@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Cc: Stephen Hemminger <stephen@networkplumber.org>
Cc: Sangtae Ha <sangtae.ha@gmail.com>
Cc: Lawrence Brakmo <lawrence@brakmo.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Issuing a CC TX_START event on control frames like pure ACK
is a waste of time, as a CC should not care.
Following patch needs this change, as we want CUBIC to properly track
idle time at a low cost, with a single TX_START being generated.
Yuchung might slightly refine the condition triggering TX_START
on a followup patch.
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Cc: Jana Iyengar <jri@google.com>
Cc: Stephen Hemminger <stephen@networkplumber.org>
Cc: Sangtae Ha <sangtae.ha@gmail.com>
Cc: Lawrence Brakmo <lawrence@brakmo.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When netlink mmap on receive side is the consumer of nf queue data,
it can happen that in some edge cases, we write skb shared info into
the user space mmap buffer:
Assume a possible rx ring frame size of only 4096, and the network skb,
which is being zero-copied into the netlink skb, contains page frags
with an overall skb->len larger than the linear part of the netlink
skb.
skb_zerocopy(), which is generic and thus not aware of the fact that
shared info cannot be accessed for such skbs then tries to write and
fill frags, thus leaking kernel data/pointers and in some corner cases
possibly writing out of bounds of the mmap area (when filling the
last slot in the ring buffer this way).
I.e. the ring buffer slot is then of status NL_MMAP_STATUS_VALID, has
an advertised length larger than 4096, where the linear part is visible
at the slot beginning, and the leaked sizeof(struct skb_shared_info)
has been written to the beginning of the next slot (also corrupting
the struct nl_mmap_hdr slot header incl. status etc), since skb->end
points to skb->data + ring->frame_size - NL_MMAP_HDRLEN.
The fix adds and lets __netlink_alloc_skb() take the actual needed
linear room for the network skb + meta data into account. It's completely
irrelevant for non-mmaped netlink sockets, but in case mmap sockets
are used, it can be decided whether the available skb_tailroom() is
really large enough for the buffer, or whether it needs to internally
fallback to a normal alloc_skb().
>From nf queue side, the information whether the destination port is
an mmap RX ring is not really available without extra port-to-socket
lookup, thus it can only be determined in lower layers i.e. when
__netlink_alloc_skb() is called that checks internally for this. I
chose to add the extra ldiff parameter as mmap will then still work:
We have data_len and hlen in nfqnl_build_packet_message(), data_len
is the full length (capped at queue->copy_range) for skb_zerocopy()
and hlen some possible part of data_len that needs to be copied; the
rem_len variable indicates the needed remaining linear mmap space.
The only other workaround in nf queue internally would be after
allocation time by f.e. cap'ing the data_len to the skb_tailroom()
iff we deal with an mmap skb, but that would 1) expose the fact that
we use a mmap skb to upper layers, and 2) trim the skb where we
otherwise could just have moved the full skb into the normal receive
queue.
After the patch, in my test case the ring slot doesn't fit and therefore
shows NL_MMAP_STATUS_COPY, where a full skb carries all the data and
thus needs to be picked up via recv().
Fixes: 3ab1f683bf8b ("nfnetlink: add support for memory mapped netlink")
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In case of netlink mmap, there can be situations where received frames
have to be placed into the normal receive queue. The ring buffer indicates
this through NL_MMAP_STATUS_COPY, so the user is asked to pick them up
via recvmsg(2) syscall, and to put the slot back to NL_MMAP_STATUS_UNUSED.
Commit 0ef707700f1c ("netlink: rx mmap: fix POLLIN condition") changed
polling, so that we walk in the worst case the whole ring through the
new netlink_has_valid_frame(), for example, when the ring would have no
NL_MMAP_STATUS_VALID, but at least one NL_MMAP_STATUS_COPY frame.
Since we do a datagram_poll() already earlier to pick up a mask that could
possibly contain POLLIN | POLLRDNORM already (due to NL_MMAP_STATUS_COPY),
we can skip checking the rx ring entirely.
In case the kernel is compiled with !CONFIG_NETLINK_MMAP, then all this is
irrelevant anyway as netlink_poll() is just defined as datagram_poll().
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
net/ipv6/route.c:2946:3-8: WARNING: NULL check before freeing functions like kfree, debugfs_remove, debugfs_remove_recursive or usb_free_urb is not needed. Maybe consider reorganizing relevant code to avoid passing NULL values.
NULL check before some freeing functions is not needed.
Based on checkpatch warning
"kfree(NULL) is safe this check is probably not required"
and kfreeaddr.cocci by Julia Lawall.
Generated by: scripts/coccinelle/free/ifnullfree.cocci
CC: Roopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This switches IPv6 policy routing to use the shared
fib_default_rule_pref() function of IPv4 and DECnet. It is also used in
multicast routing for IPv4 as well as IPv6.
The motivation for this patch is a complaint about iproute2 behaving
inconsistent between IPv4 and IPv6 when adding policy rules: Formerly,
IPv6 rules were assigned a fixed priority of 0x3FFF whereas for IPv4 the
assigned priority value was decreased with each rule added.
Since then all users of the default_pref field have been converted to
assign the generic function fib_default_rule_pref(), fib_nl_newrule()
may just use it directly instead. Therefore get rid of the function
pointer altogether and make fib_default_rule_pref() static, as it's not
used outside fib_rules.c anymore.
Signed-off-by: Phil Sutter <phil@nwl.cc>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Problem:
The ecmp route replace support for ipv6 in the kernel, deletes the
existing ecmp route too early, ie when it installs the first nexthop.
If there is an error in installing the subsequent nexthops, its too late
to recover the already deleted existing route leaving the fib
in an inconsistent state.
This patch reduces the possibility of this by doing the following:
a) Changes the existing multipath route add code to a two stage process:
build rt6_infos + insert them
ip6_route_add rt6_info creation code is moved into
ip6_route_info_create.
b) This ensures that most errors are caught during building rt6_infos
and we fail early
c) Separates multipath add and del code. Because add needs the special
two stage mode in a) and delete essentially does not care.
d) In any event if the code fails during inserting a route again, a
warning is printed (This should be unlikely)
Before the patch:
$ip -6 route show
3000:1000:1000:1000::2 via fe80::202:ff:fe00:b dev swp49s0 metric 1024
3000:1000:1000:1000::2 via fe80::202:ff:fe00:d dev swp49s1 metric 1024
3000:1000:1000:1000::2 via fe80::202:ff:fe00:f dev swp49s2 metric 1024
/* Try replacing the route with a duplicate nexthop */
$ip -6 route change 3000:1000:1000:1000::2/128 nexthop via
fe80::202:ff:fe00:b dev swp49s0 nexthop via fe80::202:ff:fe00:d dev
swp49s1 nexthop via fe80::202:ff:fe00:d dev swp49s1
RTNETLINK answers: File exists
$ip -6 route show
/* previously added ecmp route 3000:1000:1000:1000::2 dissappears from
* kernel */
After the patch:
$ip -6 route show
3000:1000:1000:1000::2 via fe80::202:ff:fe00:b dev swp49s0 metric 1024
3000:1000:1000:1000::2 via fe80::202:ff:fe00:d dev swp49s1 metric 1024
3000:1000:1000:1000::2 via fe80::202:ff:fe00:f dev swp49s2 metric 1024
/* Try replacing the route with a duplicate nexthop */
$ip -6 route change 3000:1000:1000:1000::2/128 nexthop via
fe80::202:ff:fe00:b dev swp49s0 nexthop via fe80::202:ff:fe00:d dev
swp49s1 nexthop via fe80::202:ff:fe00:d dev swp49s1
RTNETLINK answers: File exists
$ip -6 route show
3000:1000:1000:1000::2 via fe80::202:ff:fe00:b dev swp49s0 metric 1024
3000:1000:1000:1000::2 via fe80::202:ff:fe00:d dev swp49s1 metric 1024
3000:1000:1000:1000::2 via fe80::202:ff:fe00:f dev swp49s2 metric 1024
Fixes: 27596472473a ("ipv6: fix ECMP route replacement")
Signed-off-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Reviewed-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Acked-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
There was no verification that an underlying transport exists when creating
a connection, this would cause dereferencing a NULL ptr.
It might happen on sockets that weren't properly bound before attempting to
send a message, which will cause a NULL ptr deref:
[135546.047719] kasan: GPF could be caused by NULL-ptr deref or user memory accessgeneral protection fault: 0000 [#1] PREEMPT SMP DEBUG_PAGEALLOC KASAN
[135546.051270] Modules linked in:
[135546.051781] CPU: 4 PID: 15650 Comm: trinity-c4 Not tainted 4.2.0-next-20150902-sasha-00041-gbaa1222-dirty #2527
[135546.053217] task: ffff8800835bc000 ti: ffff8800bc708000 task.ti: ffff8800bc708000
[135546.054291] RIP: __rds_conn_create (net/rds/connection.c:194)
[135546.055666] RSP: 0018:ffff8800bc70fab0 EFLAGS: 00010202
[135546.056457] RAX: dffffc0000000000 RBX: 0000000000000f2c RCX: ffff8800835bc000
[135546.057494] RDX: 0000000000000007 RSI: ffff8800835bccd8 RDI: 0000000000000038
[135546.058530] RBP: ffff8800bc70fb18 R08: 0000000000000001 R09: 0000000000000000
[135546.059556] R10: ffffed014d7a3a23 R11: ffffed014d7a3a21 R12: 0000000000000000
[135546.060614] R13: 0000000000000001 R14: ffff8801ec3d0000 R15: 0000000000000000
[135546.061668] FS: 00007faad4ffb700(0000) GS:ffff880252000000(0000) knlGS:0000000000000000
[135546.062836] CS: 0010 DS: 0000 ES: 0000 CR0: 000000008005003b
[135546.063682] CR2: 000000000000846a CR3: 000000009d137000 CR4: 00000000000006a0
[135546.064723] Stack:
[135546.065048] ffffffffafe2055c ffffffffafe23fc1 ffffed00493097bf ffff8801ec3d0008
[135546.066247] 0000000000000000 00000000000000d0 0000000000000000 ac194a24c0586342
[135546.067438] 1ffff100178e1f78 ffff880320581b00 ffff8800bc70fdd0 ffff880320581b00
[135546.068629] Call Trace:
[135546.069028] ? __rds_conn_create (include/linux/rcupdate.h:856 net/rds/connection.c:134)
[135546.069989] ? rds_message_copy_from_user (net/rds/message.c:298)
[135546.071021] rds_conn_create_outgoing (net/rds/connection.c:278)
[135546.071981] rds_sendmsg (net/rds/send.c:1058)
[135546.072858] ? perf_trace_lock (include/trace/events/lock.h:38)
[135546.073744] ? lockdep_init (kernel/locking/lockdep.c:3298)
[135546.074577] ? rds_send_drop_to (net/rds/send.c:976)
[135546.075508] ? __might_fault (./arch/x86/include/asm/current.h:14 mm/memory.c:3795)
[135546.076349] ? __might_fault (mm/memory.c:3795)
[135546.077179] ? rds_send_drop_to (net/rds/send.c:976)
[135546.078114] sock_sendmsg (net/socket.c:611 net/socket.c:620)
[135546.078856] SYSC_sendto (net/socket.c:1657)
[135546.079596] ? SYSC_connect (net/socket.c:1628)
[135546.080510] ? trace_dump_stack (kernel/trace/trace.c:1926)
[135546.081397] ? ring_buffer_unlock_commit (kernel/trace/ring_buffer.c:2479 kernel/trace/ring_buffer.c:2558 kernel/trace/ring_buffer.c:2674)
[135546.082390] ? trace_buffer_unlock_commit (kernel/trace/trace.c:1749)
[135546.083410] ? trace_event_raw_event_sys_enter (include/trace/events/syscalls.h:16)
[135546.084481] ? do_audit_syscall_entry (include/trace/events/syscalls.h:16)
[135546.085438] ? trace_buffer_unlock_commit (kernel/trace/trace.c:1749)
[135546.085515] rds_ib_laddr_check(): addr 36.74.25.172 ret -99 node type -1
Acked-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If an attempt to wake up users of broadcast link is made when there is
no enough place in send queue than it may hang up inside the
tipc_sk_rcv() function since the loop breaks only after the wake up
queue becomes empty. This can lead to complete CPU stall with the
following message generated by RCU:
INFO: rcu_sched self-detected stall on CPU { 0} (t=2101 jiffies
g=54225 c=54224 q=11465)
Task dump for CPU 0:
tpch R running task 0 39949 39948 0x0000000a
ffffffff818536c0 ffff88181fa037a0 ffffffff8106a4be 0000000000000000
ffffffff818536c0 ffff88181fa037c0 ffffffff8106d8a8 ffff88181fa03800
0000000000000001 ffff88181fa037f0 ffffffff81094a50 ffff88181fa15680
Call Trace:
<IRQ> [<ffffffff8106a4be>] sched_show_task+0xae/0x120
[<ffffffff8106d8a8>] dump_cpu_task+0x38/0x40
[<ffffffff81094a50>] rcu_dump_cpu_stacks+0x90/0xd0
[<ffffffff81097c3b>] rcu_check_callbacks+0x3eb/0x6e0
[<ffffffff8106e53f>] ? account_system_time+0x7f/0x170
[<ffffffff81099e64>] update_process_times+0x34/0x60
[<ffffffff810a84d1>] tick_sched_handle.isra.18+0x31/0x40
[<ffffffff810a851c>] tick_sched_timer+0x3c/0x70
[<ffffffff8109a43d>] __run_hrtimer.isra.34+0x3d/0xc0
[<ffffffff8109aa95>] hrtimer_interrupt+0xc5/0x1e0
[<ffffffff81030d52>] ? native_smp_send_reschedule+0x42/0x60
[<ffffffff81032f04>] local_apic_timer_interrupt+0x34/0x60
[<ffffffff810335bc>] smp_apic_timer_interrupt+0x3c/0x60
[<ffffffff8165a3fb>] apic_timer_interrupt+0x6b/0x70
[<ffffffff81659129>] ? _raw_spin_unlock_irqrestore+0x9/0x10
[<ffffffff8107eb9f>] __wake_up_sync_key+0x4f/0x60
[<ffffffffa313ddd1>] tipc_write_space+0x31/0x40 [tipc]
[<ffffffffa313dadf>] filter_rcv+0x31f/0x520 [tipc]
[<ffffffffa313d699>] ? tipc_sk_lookup+0xc9/0x110 [tipc]
[<ffffffff81659259>] ? _raw_spin_lock_bh+0x19/0x30
[<ffffffffa314122c>] tipc_sk_rcv+0x2dc/0x3e0 [tipc]
[<ffffffffa312e7ff>] tipc_bclink_wakeup_users+0x2f/0x40 [tipc]
[<ffffffffa313ce26>] tipc_node_unlock+0x186/0x190 [tipc]
[<ffffffff81597c1c>] ? kfree_skb+0x2c/0x40
[<ffffffffa313475c>] tipc_rcv+0x2ac/0x8c0 [tipc]
[<ffffffffa312ff58>] tipc_l2_rcv_msg+0x38/0x50 [tipc]
[<ffffffff815a76d3>] __netif_receive_skb_core+0x5a3/0x950
[<ffffffff815a98d3>] __netif_receive_skb+0x13/0x60
[<ffffffff815a993e>] netif_receive_skb_internal+0x1e/0x90
[<ffffffff815aa138>] napi_gro_receive+0x78/0xa0
[<ffffffffa07f93f4>] tg3_poll_work+0xc54/0xf40 [tg3]
[<ffffffff81597c8c>] ? consume_skb+0x2c/0x40
[<ffffffffa07f9721>] tg3_poll_msix+0x41/0x160 [tg3]
[<ffffffff815ab0f2>] net_rx_action+0xe2/0x290
[<ffffffff8104b92a>] __do_softirq+0xda/0x1f0
[<ffffffff8104bc26>] irq_exit+0x76/0xa0
[<ffffffff81004355>] do_IRQ+0x55/0xf0
[<ffffffff8165a12b>] common_interrupt+0x6b/0x6b
<EOI>
The issue occurs only when tipc_sk_rcv() is used to wake up postponed
senders:
tipc_bclink_wakeup_users()
// wakeupq - is a queue which consists of special
// messages with SOCK_WAKEUP type.
tipc_sk_rcv(wakeupq)
...
while (skb_queue_len(inputq)) {
filter_rcv(skb)
// Here the type of message is checked
// and if it is SOCK_WAKEUP then
// it tries to wake up a sender.
tipc_write_space(sk)
wake_up_interruptible_sync_poll()
}
After the sender thread is woke up it can gather control and perform
an attempt to send a message. But if there is no enough place in send
queue it will call link_schedule_user() function which puts a message
of type SOCK_WAKEUP to the wakeup queue and put the sender to sleep.
Thus the size of the queue actually is not changed and the while()
loop never exits.
The approach I proposed is to wake up only senders for which there is
enough place in send queue so the described issue can't occur.
Moreover the same approach is already used to wake up senders on
unicast links.
I have got into the issue on our product code but to reproduce the
issue I changed a benchmark test application (from
tipcutils/demos/benchmark) to perform the following scenario:
1. Run 64 instances of test application (nodes). It can be done
on the one physical machine.
2. Each application connects to all other using TIPC sockets in
RDM mode.
3. When setup is done all nodes start simultaneously send
broadcast messages.
4. Everything hangs up.
The issue is reproducible only when a congestion on broadcast link
occurs. For example, when there are only 8 nodes it works fine since
congestion doesn't occur. Send queue limit is 40 in my case (I use a
critical importance level) and when 64 nodes send a message at the
same moment a congestion occurs every time.
Signed-off-by: Dmitry S Kolmakov <kolmakov.dmitriy@huawei.com>
Reviewed-by: Jon Maloy <jon.maloy@ericsson.com>
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Remove the unnecessary switchdev.h include from br_netlink.c.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Acked-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Since __vlan_del can return an error code, change its inner function
__vlan_vid_del to return an eventual error from switchdev_port_obj_del.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Acked-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
There's no particular desire to have conntrack action support in Open
vSwitch as an independently configurable bit, rather just to ensure
there is not a hard dependency. This exposed option doesn't accurately
reflect the conntrack dependency when enabled, so simplify this by
removing the option. Compile the support if NF_CONNTRACK is enabled.
Fixes: 7f8a436eaa2c ("openvswitch: Add conntrack action")
Signed-off-by: Joe Stringer <joestringer@nicira.com>
Acked-by: Pravin B Shelar <pshelar@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211
Johannes Berg says:
====================
For the first round of fixes, we have this:
* fix for the sizeof() pointer type issue
* a fix for regulatory getting into a restore loop
* a fix for rfkill global 'all' state, it needs to be stored
everywhere to apply correctly to new rfkill instances
* properly refuse CQM RSSI when it cannot actually be used
* protect HT TDLS traffic properly in non-HT networks
* don't incorrectly advertise 80 MHz support when not allowed
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Only return a conn if the rds_conn_net(conn) matches the struct
net passed to rds_conn_lookup().
Fixes: 467fa15356ac ("RDS-TCP: Support multiple RDS-TCP listen endpoints,
one per netns.")
Signed-off-by: Sowmini Varadhan <sowmini.varadhan@oracle.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
switchdev_port_fdb_dump is used as .ndo_fdb_dump. Its return value is
idx, so we cannot return errval.
Fixes: 45d4122ca7cd ("switchdev: add support for fdb add/del/dump via switchdev_port_obj ops.")
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Acked-by: Sridhar Samudrala <sridhar.samudrala@intel.com>
Acked-by: Scott Feldman<sfeldma@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Conflicts:
include/net/netfilter/nf_conntrack.h
The conflict was an overlap between changing the type of the zone
argument to nf_ct_tmpl_alloc() whilst exporting nf_ct_tmpl_free.
Pablo Neira Ayuso says:
====================
Netfilter fixes for net
The following patchset contains Netfilter fixes for net, they are:
1) Oneliner to restore maps in nf_tables since we support addressing registers
at 32 bits level.
2) Restore previous default behaviour in bridge netfilter when CONFIG_IPV6=n,
oneliner from Bernhard Thaler.
3) Out of bound access in ipset hash:net* set types, reported by Dave Jones'
KASan utility, patch from Jozsef Kadlecsik.
4) Fix ipset compilation with gcc 4.4.7 related to C99 initialization of
unnamed unions, patch from Elad Raz.
5) Add a workaround to address inconsistent endianess in the res_id field of
nfnetlink batch messages, reported by Florian Westphal.
6) Fix error paths of CT/synproxy since the conntrack template was moved to use
kmalloc, patch from Daniel Borkmann.
All of them look good to me to reach 4.2, I can route this to -stable myself
too, just let me know what you prefer.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In the IPv6 multicast routing code the mrt_lock was not being released
correctly in the MFC iterator, as a result adding or deleting a MIF would
cause a hang because the mrt_lock could not be acquired.
This fix is a copy of the code for the IPv4 case and ensures that the lock
is released correctly.
Signed-off-by: Richard Laing <richard.laing@alliedtelesis.co.nz>
Acked-by: Cong Wang <cwang@twopensource.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When beacon filtering is enabled the mac80211 software implementation
for RSSI CQM cannot work as beacons will not be available. Rather than
accepting such a configuration without proper effect, reject it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Currently if 80MHz channels are not allowed for use, the VHT IE is not
included in the probe request for an AP. This is not good enough if the
AP is configured with the wrong regulatory and supports VHT even where
prohibited or in TDLS scenarios.
Mark the ifmgd with the DISABLE_VHT flag for the misbehaving-AP case, and
unset VHT support from the peer-station entry for the TDLS case.
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
restore_regulatory_settings() should restore alpha2
as computed in restore_alpha2(), not raw user_alpha2 to
behave as described in the comment just above that code.
This fixes endless loop of calling CRDA for "00" and "97"
countries after resume from suspend on my laptop.
Looks like others had the same problem, too:
http://ath9k-devel.ath9k.narkive.com/knY5W6St/ath9k-and-crda-messages-in-logs
https://bugs.launchpad.net/ubuntu/+source/linux/+bug/899335
https://forum.porteus.org/viewtopic.php?t=4975&p=36436
https://forums.opensuse.org/showthread.php/483356-Authentication-Regulatory-Domain-issues-ath5k-12-2
Signed-off-by: Maciej Szmigiero <mail@maciej.szmigiero.name>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
When switching the state of all RFKill switches of type all we need to
replicate the RFKILL_TYPE_ALL global state to all the other types global
state, so it is used to initialize persistent RFKill switches on
register.
Signed-off-by: João Paulo Rechi Vita <jprvita@endlessm.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
HT TDLS traffic should be protected in a non-HT BSS to avoid
collisions. Therefore, when TDLS peers join/leave, check if
protection is (now) needed and set the ht_operation_mode of
the virtual interface according to the HT capabilities of the
TDLS peer(s).
This works because a non-HT BSS connection never sets (or
otherwise uses) the ht_operation_mode; it just means that
drivers must be aware that this field applies to all HT
traffic for this virtual interface, not just the traffic
within the BSS. Document that.
Signed-off-by: Avri Altman <avri.altman@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
The rate_control_cap_mask() function takes a parameter mcs_mask, which
GCC will take to be u8 * even though it was declared with a fixed size.
This causes the following warning:
net/mac80211/rate.c: In function 'rate_control_cap_mask':
net/mac80211/rate.c:719:25: warning: 'sizeof' on array function parameter 'mcs_mask' will return size of 'u8 * {aka unsigned char *}' [-Wsizeof-array-argument]
for (i = 0; i < sizeof(mcs_mask); i++)
^
net/mac80211/rate.c:684:10: note: declared here
u8 mcs_mask[IEEE80211_HT_MCS_MASK_LEN],
^
This can be easily fixed by using the IEEE80211_HT_MCS_MASK_LEN directly
within the loop condition.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Commit 0ca50d12fe46 added a restriction that the address must belong to
the output interface, so that sctp will use the right interface even
when using secondary addresses.
But it breaks IPVS setups, on which people is used to attach VIP
addresses to loopback interface on real servers. It's preferred to
attach to the interface actually in use, but it's a very common setup
and that used to work.
This patch then saves the first routing good result, even if it would be
going out through an interface that doesn't have that address. If no
better hit found, it's then used. This effectively restores the original
behavior if no better interface could be found.
Fixes: 0ca50d12fe46 ("sctp: fix src address selection if using secondary addresses")
Signed-off-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Commit 0ca50d12fe46 failed to release the reference to dst entries that
it decided to skip.
Fixes: 0ca50d12fe46 ("sctp: fix src address selection if using secondary addresses")
Signed-off-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Pull networking updates from David Miller:
"Another merge window, another set of networking changes. I've heard
rumblings that the lightweight tunnels infrastructure has been voted
networking change of the year. But what do I know?
1) Add conntrack support to openvswitch, from Joe Stringer.
2) Initial support for VRF (Virtual Routing and Forwarding), which
allows the segmentation of routing paths without using multiple
devices. There are some semantic kinks to work out still, but
this is a reasonably strong foundation. From David Ahern.
3) Remove spinlock fro act_bpf fast path, from Alexei Starovoitov.
4) Ignore route nexthops with a link down state in ipv6, just like
ipv4. From Andy Gospodarek.
5) Remove spinlock from fast path of act_gact and act_mirred, from
Eric Dumazet.
6) Document the DSA layer, from Florian Fainelli.
7) Add netconsole support to bcmgenet, systemport, and DSA. Also
from Florian Fainelli.
8) Add Mellanox Switch Driver and core infrastructure, from Jiri
Pirko.
9) Add support for "light weight tunnels", which allow for
encapsulation and decapsulation without bearing the overhead of a
full blown netdevice. From Thomas Graf, Jiri Benc, and a cast of
others.
10) Add Identifier Locator Addressing support for ipv6, from Tom
Herbert.
11) Support fragmented SKBs in iwlwifi, from Johannes Berg.
12) Allow perf PMUs to be accessed from eBPF programs, from Kaixu Xia.
13) Add BQL support to 3c59x driver, from Loganaden Velvindron.
14) Stop using a zero TX queue length to mean that a device shouldn't
have a qdisc attached, use an explicit flag instead. From Phil
Sutter.
15) Use generic geneve netdevice infrastructure in openvswitch, from
Pravin B Shelar.
16) Add infrastructure to avoid re-forwarding a packet in software
that was already forwarded by a hardware switch. From Scott
Feldman.
17) Allow AF_PACKET fanout function to be implemented in a bpf
program, from Willem de Bruijn"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1458 commits)
netfilter: nf_conntrack: make nf_ct_zone_dflt built-in
netfilter: nf_dup{4, 6}: fix build error when nf_conntrack disabled
net: fec: clear receive interrupts before processing a packet
ipv6: fix exthdrs offload registration in out_rt path
xen-netback: add support for multicast control
bgmac: Update fixed_phy_register()
sock, diag: fix panic in sock_diag_put_filterinfo
flow_dissector: Use 'const' where possible.
flow_dissector: Fix function argument ordering dependency
ixgbe: Resolve "initialized field overwritten" warnings
ixgbe: Remove bimodal SR-IOV disabling
ixgbe: Add support for reporting 2.5G link speed
ixgbe: fix bounds checking in ixgbe_setup_tc for 82598
ixgbe: support for ethtool set_rxfh
ixgbe: Avoid needless PHY access on copper phys
ixgbe: cleanup to use cached mask value
ixgbe: Remove second instance of lan_id variable
ixgbe: use kzalloc for allocating one thing
flow: Move __get_hash_from_flowi{4,6} into flow_dissector.c
ixgbe: Remove unused PCI bus types
...
|
|
Fengguang reported, that some randconfig generated the following linker
issue with nf_ct_zone_dflt object involved:
[...]
CC init/version.o
LD init/built-in.o
net/built-in.o: In function `ipv4_conntrack_defrag':
nf_defrag_ipv4.c:(.text+0x93e95): undefined reference to `nf_ct_zone_dflt'
net/built-in.o: In function `ipv6_defrag':
nf_defrag_ipv6_hooks.c:(.text+0xe3ffe): undefined reference to `nf_ct_zone_dflt'
make: *** [vmlinux] Error 1
Given that configurations exist where we have a built-in part, which is
accessing nf_ct_zone_dflt such as the two handlers nf_ct_defrag_user()
and nf_ct6_defrag_user(), and a part that configures nf_conntrack as a
module, we must move nf_ct_zone_dflt into a fixed, guaranteed built-in
area when netfilter is configured in general.
Therefore, split the more generic parts into a common header under
include/linux/netfilter/ and move nf_ct_zone_dflt into the built-in
section that already holds parts related to CONFIG_NF_CONNTRACK in the
netfilter core. This fixes the issue on my side.
Fixes: 308ac9143ee2 ("netfilter: nf_conntrack: push zone object into functions")
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
While testing various Kconfig options on another issue, I found that
the following one triggers as well on allmodconfig and nf_conntrack
disabled:
net/ipv4/netfilter/nf_dup_ipv4.c: In function ‘nf_dup_ipv4’:
net/ipv4/netfilter/nf_dup_ipv4.c:72:20: error: ‘nf_skb_duplicated’ undeclared (first use in this function)
if (this_cpu_read(nf_skb_duplicated))
[...]
net/ipv6/netfilter/nf_dup_ipv6.c: In function ‘nf_dup_ipv6’:
net/ipv6/netfilter/nf_dup_ipv6.c:66:20: error: ‘nf_skb_duplicated’ undeclared (first use in this function)
if (this_cpu_read(nf_skb_duplicated))
Fix it by including directly the header where it is defined.
Fixes: bbde9fc1824a ("netfilter: factor out packet duplication for IPv4/IPv6")
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We previously register IPPROTO_ROUTING offload under inet6_add_offload(),
but in error path, we try to unregister it with inet_del_offload(). This
doesn't seem correct, it should actually be inet6_del_offload(), also
ipv6_exthdrs_offload_exit() from that commit seems rather incorrect (it
also uses rthdr_offload twice), but it got removed entirely later on.
Fixes: 3336288a9fea ("ipv6: Switch to using new offload infrastructure.")
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
diag socket's sock_diag_put_filterinfo() dumps classic BPF programs
upon request to user space (ss -0 -b). However, native eBPF programs
attached to sockets (SO_ATTACH_BPF) cannot be dumped with this method:
Their orig_prog is always NULL. However, sock_diag_put_filterinfo()
unconditionally tries to access its filter length resp. wants to copy
the filter insns from there. Internal cBPF to eBPF transformations
attached to sockets don't have this issue, as orig_prog state is kept.
It's currently only used by packet sockets. If we would want to add
native eBPF support in the future, this needs to be done through
a different attribute than PACKET_DIAG_FILTER to not confuse possible
user space disassemblers that work on diag data.
Fixes: 89aa075832b0 ("net: sock: allow eBPF programs to be attached to sockets")
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Acked-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
These cannot live in net/core/flow.c which only builds when XFRM is
enabled.
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Just have a flags member instead.
In file included from include/linux/linkage.h:4:0,
from include/linux/kernel.h:6,
from net/core/flow_dissector.c:1:
In function 'flow_keys_hash_start',
inlined from 'flow_hash_from_keys' at net/core/flow_dissector.c:553:34:
>> include/linux/compiler.h:447:38: error: call to '__compiletime_assert_459' declared with attribute error: BUILD_BUG_ON failed: FLOW_KEYS_HASH_OFFSET % sizeof(u32)
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In ___skb_get_hash ignore return value from skb_flow_dissect_flow_keys.
A failure in that function likely means that there was a parse error,
so we may as well use whatever fields were found before the error was
hit. This is also good because it means we won't keep trying to derive
the hash on subsequent calls to skb_get_hash for the same packet.
Signed-off-by: Tom Herbert <tom@herbertland.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add an input flag to flow dissector on rather dissection should stop
when encapsulation is detected (IP/IP or GRE). Also, add a key_control
flag that indicates encapsulation was encountered during the
dissection.
Signed-off-by: Tom Herbert <tom@herbertland.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add an input flag to flow dissector on rather dissection should be
stopped when a flow label is encountered. Presumably, the flow label
is derived from a sufficient hash of an inner transport packet so
further dissection is not needed (that is ports are not included in
the flow hash). Using the flow label instead of ports has the additional
benefit that packet fragments should hash to same value as non-fragments
for a flow (assuming that the same flow label is used).
We set this flag by default in for skb_get_hash.
Signed-off-by: Tom Herbert <tom@herbertland.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add an input flag to flow dissector on rather dissection should be
stopped when an L3 packet is encountered. This would be useful if a
caller just wanted to get IP addresses of the outermost header (e.g.
to do an L3 hash).
Signed-off-by: Tom Herbert <tom@herbertland.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Parse NEXTHDR_FRAGMENT. When seen account for it in the fragment bits of
key_control. Also, check if first fragment should be parsed.
Signed-off-by: Tom Herbert <tom@herbertland.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add an input flag to flow dissector on rather dissection should be
attempted on a first fragment. Also add key_control flags to indicate
that a packet is a fragment or first fragment.
Signed-off-by: Tom Herbert <tom@herbertland.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The flags argument will allow control of the dissection process (for
instance whether to parse beyond L3).
Signed-off-by: Tom Herbert <tom@herbertland.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Instead of returning immediately (on a parsing failure for instance) we
jump to cleanup code. This always sets protocol values in key_control
(even on a failure there is still valid information in the key_tags that
was set before the problem was hit).
Signed-off-by: Tom Herbert <tom@herbertland.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Create __get_hash_from_flowi6 and __get_hash_from_flowi4 to get the
flow keys and hash based on flowi structures. These are called by
__skb_get_hash_flowi6 and __skb_get_hash_flowi4. Also, created
get_hash_from_flowi6 and get_hash_from_flowi4 which can be called
when just the hash value for a flowi is needed.
Signed-off-by: Tom Herbert <tom@herbertland.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Move __skb_set_sw_hash to skbuff.h and add __skb_set_hash which is
a common method (between __skb_set_sw_hash and skb_set_hash) to set
the hash in an skbuff.
Also, move skb_clear_hash to be closer to __skb_set_hash.
Signed-off-by: Tom Herbert <tom@herbertland.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
A number of VRF patches used 'int' for table id. It should be u32 to be
consistent with the rest of the stack.
Fixes:
4e3c89920cd3a ("net: Introduce VRF related flags and helpers")
15be405eb2ea9 ("net: Add inet_addr lookup by table")
30bbaa1950055 ("net: Fix up inet_addr_type checks")
021dd3b8a142d ("net: Add routes to the table associated with the device")
dc028da54ed35 ("inet: Move VRF table lookup to inlined function")
f6d3c19274c74 ("net: FIB tracepoints")
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Reviewed-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Commit 0838aa7fcfcd ("netfilter: fix netns dependencies with conntrack
templates") migrated templates to the new allocator api, but forgot to
update error paths for them in CT and synproxy to use nf_ct_tmpl_free()
instead of nf_conntrack_free().
Due to that, memory is being freed into the wrong kmemcache, but also
we drop the per net reference count of ct objects causing an imbalance.
In Brad's case, this leads to a wrap-around of net->ct.count and thus
lets __nf_conntrack_alloc() refuse to create a new ct object:
[ 10.340913] xt_addrtype: ipv6 does not support BROADCAST matching
[ 10.810168] nf_conntrack: table full, dropping packet
[ 11.917416] r8169 0000:07:00.0 eth0: link up
[ 11.917438] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 12.815902] nf_conntrack: table full, dropping packet
[ 15.688561] nf_conntrack: table full, dropping packet
[ 15.689365] nf_conntrack: table full, dropping packet
[ 15.690169] nf_conntrack: table full, dropping packet
[ 15.690967] nf_conntrack: table full, dropping packet
[...]
With slab debugging, it also reports the wrong kmemcache (kmalloc-512 vs.
nf_conntrack_ffffffff81ce75c0) and reports poison overwrites, etc. Thus,
to fix the problem, export and use nf_ct_tmpl_free() instead.
Fixes: 0838aa7fcfcd ("netfilter: fix netns dependencies with conntrack templates")
Reported-by: Brad Jackson <bjackson0971@gmail.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
opts_size is only written and never read. Following patch
removes this unused variable.
Signed-off-by: Pravin B Shelar <pshelar@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Marius Tomaschewski <mt@suse.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Pull crypto updates from Herbert Xu:
"Here is the crypto update for 4.3:
API:
- the AEAD interface transition is now complete.
- add top-level skcipher interface.
Drivers:
- x86-64 acceleration for chacha20/poly1305.
- add sunxi-ss Allwinner Security System crypto accelerator.
- add RSA algorithm to qat driver.
- add SRIOV support to qat driver.
- add LS1021A support to caam.
- add i.MX6 support to caam"
* git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6: (163 commits)
crypto: algif_aead - fix for multiple operations on AF_ALG sockets
crypto: qat - enable legacy VFs
MPI: Fix mpi_read_buffer
crypto: qat - silence a static checker warning
crypto: vmx - Fixing opcode issue
crypto: caam - Use the preferred style for memory allocations
crypto: caam - Propagate the real error code in caam_probe
crypto: caam - Fix the error handling in caam_probe
crypto: caam - fix writing to JQCR_MS when using service interface
crypto: hash - Add AHASH_REQUEST_ON_STACK
crypto: testmgr - Use new skcipher interface
crypto: skcipher - Add top-level skcipher interface
crypto: cmac - allow usage in FIPS mode
crypto: sahara - Use dmam_alloc_coherent
crypto: caam - Add support for LS1021A
crypto: qat - Don't move data inside output buffer
crypto: vmx - Fixing GHASH Key issue on little endian
crypto: vmx - Fixing AES-CTR counter bug
crypto: null - Add missing Kconfig tristate for NULL2
crypto: nx - Add forward declaration for struct crypto_aead
...
|
|
The kernel is applying the RA managed/otherconf flags silently and
forgets to send ifinfo notify to inform about their change when the
router provides a zero reachable_time and retrans_timer as dnsmasq
and many routers send it, which just means unspecified by this router
and the host should continue using whatever value it is already using.
Userspace may monitor the ifinfo notifications to activate dhcpv6.
Signed-off-by: Marius Tomaschewski <mt@suse.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
It can be useful for DSA and CPU ports to have a phy-mode property, in
particular to specify RGMII delays. Parse the property and set it in
the fixed-link phydev.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
