| Age | Commit message (Collapse) | Author |
|---|
|
This action allows for a sending side to encapsulate arbitrary metadata
which is decapsulated by the receiving end.
The sender runs in encoding mode and the receiver in decode mode.
Both sender and receiver must specify the same ethertype.
At some point we hope to have a registered ethertype and we'll
then provide a default so the user doesnt have to specify it.
For now we enforce the user specify it.
Lets show example usage where we encode icmp from a sender towards
a receiver with an skbmark of 17; both sender and receiver use
ethertype of 0xdead to interop.
YYYY: Lets start with Receiver-side policy config:
xxx: add an ingress qdisc
sudo tc qdisc add dev $ETH ingress
xxx: any packets with ethertype 0xdead will be subjected to ife decoding
xxx: we then restart the classification so we can match on icmp at prio 3
sudo $TC filter add dev $ETH parent ffff: prio 2 protocol 0xdead \
u32 match u32 0 0 flowid 1:1 \
action ife decode reclassify
xxx: on restarting the classification from above if it was an icmp
xxx: packet, then match it here and continue to the next rule at prio 4
xxx: which will match based on skb mark of 17
sudo tc filter add dev $ETH parent ffff: prio 3 protocol ip \
u32 match ip protocol 1 0xff flowid 1:1 \
action continue
xxx: match on skbmark of 0x11 (decimal 17) and accept
sudo tc filter add dev $ETH parent ffff: prio 4 protocol ip \
handle 0x11 fw flowid 1:1 \
action ok
xxx: Lets show the decoding policy
sudo tc -s filter ls dev $ETH parent ffff: protocol 0xdead
xxx:
filter pref 2 u32
filter pref 2 u32 fh 800: ht divisor 1
filter pref 2 u32 fh 800::800 order 2048 key ht 800 bkt 0 flowid 1:1 (rule hit 0 success 0)
match 00000000/00000000 at 0 (success 0 )
action order 1: ife decode action reclassify
index 1 ref 1 bind 1 installed 14 sec used 14 sec
type: 0x0
Metadata: allow mark allow hash allow prio allow qmap
Action statistics:
Sent 0 bytes 0 pkt (dropped 0, overlimits 0 requeues 0)
backlog 0b 0p requeues 0
xxx:
Observe that above lists all metadatum it can decode. Typically these
submodules will already be compiled into a monolithic kernel or
loaded as modules
YYYY: Lets show the sender side now ..
xxx: Add an egress qdisc on the sender netdev
sudo tc qdisc add dev $ETH root handle 1: prio
xxx:
xxx: Match all icmp packets to 192.168.122.237/24, then
xxx: tag the packet with skb mark of decimal 17, then
xxx: Encode it with:
xxx: ethertype 0xdead
xxx: add skb->mark to whitelist of metadatum to send
xxx: rewrite target dst MAC address to 02:15:15:15:15:15
xxx:
sudo $TC filter add dev $ETH parent 1: protocol ip prio 10 u32 \
match ip dst 192.168.122.237/24 \
match ip protocol 1 0xff \
flowid 1:2 \
action skbedit mark 17 \
action ife encode \
type 0xDEAD \
allow mark \
dst 02:15:15:15:15:15
xxx: Lets show the encoding policy
sudo tc -s filter ls dev $ETH parent 1: protocol ip
xxx:
filter pref 10 u32
filter pref 10 u32 fh 800: ht divisor 1
filter pref 10 u32 fh 800::800 order 2048 key ht 800 bkt 0 flowid 1:2 (rule hit 0 success 0)
match c0a87aed/ffffffff at 16 (success 0 )
match 00010000/00ff0000 at 8 (success 0 )
action order 1: skbedit mark 17
index 6 ref 1 bind 1
Action statistics:
Sent 0 bytes 0 pkt (dropped 0, overlimits 0 requeues 0)
backlog 0b 0p requeues 0
action order 2: ife encode action pipe
index 3 ref 1 bind 1
dst MAC: 02:15:15:15:15:15 type: 0xDEAD
Metadata: allow mark
Action statistics:
Sent 0 bytes 0 pkt (dropped 0, overlimits 0 requeues 0)
backlog 0b 0p requeues 0
xxx:
test by sending ping from sender to destination
Signed-off-by: Jamal Hadi Salim <jhs@mojatatu.com>
Acked-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next
Johannes Berg says:
====================
Here's another round of updates for -next:
* big A-MSDU RX performance improvement (avoid linearize of paged RX)
* rfkill changes: cleanups, documentation, platform properties
* basic PBSS support in cfg80211
* MU-MIMO action frame processing support
* BlockAck reordering & duplicate detection offload support
* various cleanups & little fixes
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Allow for more multicast router port information to be dumped such as
timer and type attributes. For that that purpose we need to extend the
MDBA_ROUTER_PORT attribute similar to how it was done for the mdb entries
recently. The new format is thus:
[MDBA_ROUTER_PORT] = { <- nested attribute
u32 ifindex <- router port ifindex for user-space compatibility
[MDBA_ROUTER_PATTR attributes]
}
This way it remains compatible with older users (they'll simply retrieve
the u32 in the beginning) and new users can parse the remaining
attributes. It would also allow to add future extensions to the router
port without breaking compatibility.
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add support for a temporary router port which doesn't depend only on the
incoming query. It can be refreshed if set to the same value, which is
a no-op for the rest.
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This is needed for the upcoming temporary port router. There's no point
to go through the logic if the value is the same.
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Using raw values makes it difficult to extend and also understand the
code, give them names and do explicit per-option manipulation in
br_multicast_set_port_router.
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When a user explicitly requests VLAN filtering with something like:
# echo 1 > /sys/class/net/<bridge>/bridge/vlan_filtering
Switchdev propagates a SWITCHDEV_ATTR_ID_BRIDGE_VLAN_FILTERING port
attribute.
Add support for it in the DSA layer with a new port_vlan_filtering
function to let drivers toggle 802.1Q filtering on user demand.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Introduce devlink infrastructure for drivers to register and expose to
userspace via generic Netlink interface.
There are two basic objects defined:
devlink - one instance for every "parent device", for example switch ASIC
devlink port - one instance for every physical port of the device.
This initial portion implements basic get/dump of objects to userspace.
Also, port splitter and port type setting is implemented.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In the initial implementation the only way to stop a rule from being
inserted into the hardware table was via the device feature flag.
However this doesn't work well when working on an end host system
where packets are expect to hit both the hardware and software
datapaths.
For example we can imagine a rule that will match an IP address and
increment a field. If we install this rule in both hardware and
software we may increment the field twice. To date we have only
added support for the drop action so we have been able to ignore
these cases. But as we extend the action support we will hit this
example plus more such cases. Arguably these are not even corner
cases in many working systems these cases will be common.
To avoid forcing the driver to always abort (i.e. the above example)
this patch adds a flag to add a rule in software only. A careful
user can use this flag to build software and hardware datapaths
that work together. One example we have found particularly useful
is to use hardware resources to set the skb->mark on the skb when
the match may be expensive to run in software but a mark lookup
in a hash table is cheap. The idea here is hardware can do in one
lookup what the u32 classifier may need to traverse multiple lists
and hash tables to compute. The flag is only passed down on inserts.
On deletion to avoid stale references in hardware we always try
to remove a rule if it exists.
The flags field is part of the classifier specific options. Although
it is tempting to lift this into the generic structure doing this
proves difficult do to how the tc netlink attributes are implemented
along with how the dump/change routines are called. There is also
precedence for putting seemingly generic pieces in the specific
classifier options such as TCA_U32_POLICE, TCA_U32_ACT, etc. So
although not ideal I've left FLAGS in the u32 options as well as it
simplifies the code greatly and user space has already learned how
to manage these bits ala 'tc' tool.
Another thing if trying to update a rule we require the flags to
be unchanged. This is to force user space, software u32 and
the hardware u32 to keep in sync. Thanks to Simon Horman for
catching this case.
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The offload decision was originally very basic and tied to if the dev
implemented the appropriate ndo op hook. The next step is to allow
the user to more flexibly define if any paticular rule should be
offloaded or not. In order to have this logic in one function lift
the current check into a helper routine tc_should_offload().
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch implements bookkeeping support to compute the maximum
headroom for all the devices in each datapath. When said value
changes, the underlying devs are notified via the
ndo_set_rx_headroom method.
This also increases the internal vports xmit performance.
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
On bridge needed_headroom changes, the enslaved devices are
notified via the ndo_set_rx_headroom method
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
RTS/CTS needs to be enabled if the rate is a fallback rate *or* if it's
a dual-stream rate and the sta is in dynamic SMPS mode.
Cc: stable@vger.kernel.org
Fixes: a3ebb4e1b763 ("mac80211: minstrel_ht: handle peers in dynamic SMPS")
Reported-by: Matías Richart <mrichart@fing.edu.uy>
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Public Action frames use special rules for how the BSSID field (Address
3) is set. A wildcard BSSID is used in cases where the transmitter and
recipient are not members of the same BSS. As such, we need to accept
Public Action frames with wildcard BSSID.
Commit db8e17324553 ("mac80211: ignore frames between TDLS peers when
operating as AP") added a rule that drops Action frames to TDLS-peers
based on an Action frame having different DA (Address 1) and BSSID
(Address 3) values. This is not correct since it misses the possibility
of BSSID being a wildcard BSSID in which case the Address 1 would not
necessarily match.
Fix this by allowing mac80211 to accept wildcard BSSID in an Action
frame when in AP mode.
Fixes: db8e17324553 ("mac80211: ignore frames between TDLS peers when operating as AP")
Cc: stable@vger.kernel.org
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Just like for CCMP we need to check that for GCMP the fragments
have PNs that increment by one; the spec was updated to fix this
security issue and now has the following text:
The receiver shall discard MSDUs and MMPDUs whose constituent
MPDU PN values are not incrementing in steps of 1.
Adapt the code for CCMP to work for GCMP as well, luckily the
relevant fields already alias each other so no code duplication
is needed (just check the aliasing with BUILD_BUG_ON.)
Cc: stable@vger.kernel.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Similarly, we need to update backlog too when we update qlen.
Cc: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We saw qlen!=0 but backlog==0 on our production machine:
qdisc htb 1: dev eth0 root refcnt 2 r2q 10 default 1 direct_packets_stat 0 ver 3.17
Sent 172680457356 bytes 222469449 pkt (dropped 0, overlimits 123575834 requeues 0)
backlog 0b 72p requeues 0
The problem is we only count qlen for HTB qdisc but not backlog.
We need to update backlog too when we update qlen, so that we
can at least know the average packet length.
Cc: Jamal Hadi Salim <jhs@mojatatu.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When the bottom qdisc decides to, for example, drop some packet,
it calls qdisc_tree_decrease_qlen() to update the queue length
for all its ancestors, we need to update the backlog too to
keep the stats on root qdisc accurate.
Cc: Jamal Hadi Salim <jhs@mojatatu.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Remove nearly duplicated code and prepare for the following patch.
Cc: Jamal Hadi Salim <jhs@mojatatu.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
While building with W=1 we got the warning:
net/netfilter/xt_osf.c:265:9: warning: variable 'loop_cont' set but not used
The local variable loop_cont was only initialized and then assigned a
value but was never used or checked after that.
While removing the variable, the case of OSFOPT_TS was not removed so
that it will serve as a reminder to us that we can do something in that
particular case.
Signed-off-by: Sudip Mukherjee <sudip.mukherjee@codethink.co.uk>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
Can be used to randomly match packets e.g. for statistic traffic sampling.
See commit 3ad0040573b0c00f8848
("bpf: split state from prandom_u32() and consolidate {c, e}BPF prngs")
for more info why this doesn't use prandom_u32 directly.
Unlike bpf nft_meta can be built as a module, so add an EXPORT_SYMBOL
for prandom_seed_full_state too.
Cc: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
nfacct_filter_alloc doesn't validate the NFACCT_FILTER_MASK and
NFACCT_FILTER_VALUE parameters which can trigger a NULL pointer
dereference. CAP_NET_ADMIN is required to trigger the bug.
Signed-off-by: Phil Turnbull <phil.turnbull@oracle.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Signed-off-by: Antonio Quartulli <a@unstable.cc>
|
|
Lists all neighbours detected by the Echo Locating Protocol
(ELP) and their throughput metric.
Initially Developed by Linus during a 6 months trainee study
period in Ascom (Switzerland) AG.
Signed-off-by: Linus Luessing <linus.luessing@web.de>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Antonio Quartulli <antonio@open-mesh.com>
|
|
Signed-off-by: Antonio Quartulli <antonio@open-mesh.com>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
|
|
Signed-off-by: Antonio Quartulli <antonio@open-mesh.com>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
|
|
In case of an unused wireless link, the mac80211 throughput estimation
won't get updated further. Consequently, the reported throughput metric
will become obsolete.
With this patch unicast sampling is introduced by periodically sending
unicast ELP packets to each neighbor on idle WiFi links. These sampling
packets will fill an entire frame, so that the measurement is as
reliable as possible
Signed-off-by: Antonio Quartulli <antonio@open-mesh.com>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
|
|
In case of wireless interface retrieve the throughput by
querying cfg80211. To perform this call a separate work
must be scheduled because the function may sleep and this
is not allowed within an RCU protected context (RCU in this
case is used to iterate over all the neighbours).
Use ethtool to retrieve information about an Ethernet link
like HALF/FULL_DUPLEX and advertised bandwidth (e.g.
100/10Mbps).
The metric is updated each time a new ELP packet is sent,
this way it is possible to timely react to a metric
variation which can imply (for example) a neighbour
disconnection.
Signed-off-by: Antonio Quartulli <antonio@open-mesh.com>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
|
|
To enable ELP to send probing packets over wireless links
only if needed, batman-adv must keep track of the last time
it sent a unicast packet towards every neighbour.
For this purpose a 2 main changes are introduced:
1) a new member of the elp_neigh_node structure stores the
last time a unicast packet was sent towards this neighbour;
2) a wrapper function for sending unicast packets is
implemented. This function will simply update the member
describe din point 1) and then forward the packet to the
real sending routine.
Point 2) implies that any code-path leading to a unicast
sending now has to use the new wrapper.
Signed-off-by: Antonio Quartulli <antonio@open-mesh.com>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
|
|
This attribute is exported to user space to disable the link
throughput auto-detection by setting a fixed value.
The throughput override value is used when batman-adv is
computing the link throughput towards a neighbour.
If the value is set to 0 then batman-adv will try to detect
the throughput by itself.
Signed-off-by: Antonio Quartulli <antonio@open-mesh.com>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
|
|
Add the support for recognising new originators in the
network and rebroadcast their OGMs.
Signed-off-by: Antonio Quartulli <antonio@open-mesh.com>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
|
|
This is the initial implementation of the new OGM protocol
(version 2). It has been designed to work on top of the
newly added ELP.
In the previous version the OGM protocol was used to both
measure link qualities and flood the network with the metric
information. In this version the protocol is in charge of
the latter task only, leaving the former to ELP.
This means being able to decouple the interval used by the
neighbor discovery from the OGM broadcasting, which revealed
to be costly in dense networks and needed to be relaxed so
leading to a less responsive routing protocol.
Signed-off-by: Antonio Quartulli <antonio@open-mesh.com>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
|
|
This parameter can be set individually on each interface and
allows the configuration of the elp interval for the link
quality measurements during runtime. Usually it is desirable
to set it to a higher (= slower) value on interfaces which
have a more static characteristic (e.g. wired interfaces)
or very dense neighbourhoods to reduce overhead.
Developed by Linus during a 6 months trainee study period in
Ascom (Switzerland) AG.
Signed-off-by: Linus Luessing <linus.luessing@web.de>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
[antonio@open-mesh.com: respin on top of the latest master]
Signed-off-by: Antonio Quartulli <antonio@open-mesh.com>
|
|
Initially developed by Linus during a 6 months trainee study
period in Ascom (Switzerland) AG.
Signed-off-by: Linus Luessing <linus.luessing@web.de>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Antonio Quartulli <antonio@open-mesh.com>
|
|
The B.A.T.M.A.N. protocol originally only used a single
message type (called OGM) to determine the link qualities to
the direct neighbors and spreading these link quality
information through the whole mesh. This procedure is
summarized on the BATMAN concept page and explained in
details in the RFC draft published in 2008.
This approach was chosen for its simplicity during the
protocol design phase and the implementation. However, it
also bears some drawbacks:
* Wireless interfaces usually come with some packet loss,
therefore a higher broadcast rate is desirable to allow
a fast reaction on flaky connections.
Other interfaces of the same host might be connected to
Ethernet LANs / VPNs / etc which rarely exhibit packet
loss would benefit from a lower broadcast rate to reduce
overhead.
* It generally is more desirable to detect local link
quality changes at a faster rate than propagating all
these changes through the entire mesh (the far end of
the mesh does not need to care about local link quality
changes that much). Other optimizations strategies, like
reducing overhead, might be possible if OGMs weren't
used for all tasks in the mesh at the same time.
As a result detecting local link qualities shall be handled
by an independent message type, ELP, whereas the OGM message
type remains responsible for flooding the mesh with these
link quality information and determining the overall path
transmit qualities.
Developed by Linus during a 6 months trainee study period in
Ascom (Switzerland) AG.
Signed-off-by: Linus Luessing <linus.luessing@web.de>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Antonio Quartulli <antonio@open-mesh.com>
|
|
This allows us to easily add a sysfs parameter for an
unsigned int later, which is not for a batman mesh interface
(e.g. bat0), but for a common interface instead. It allows
reading and writing an atomic_t in hard_iface (instead of
bat_priv compared to the mesh variant).
Developed by Linus during a 6 months trainee study period in
Ascom (Switzerland) AG.
Signed-off-by: Linus Luessing <linus.luessing@web.de>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
[antonio@open-mesh.com: rename functions and move macros]
Signed-off-by: Antonio Quartulli <antonio@open-mesh.com>
|
|
When the send skbuff reaches the end, nlmsg_put and friends returns
-EMSGSIZE but it is silently thrown away in ndo_fdb_dump. It is called
within a for_each_netdev loop and the first fdb entry of a following
netdev could fit in the remaining skbuff. This breaks the mechanism
of cb->args[0] and idx to keep track of the entries that are already
dumped, which results missing entries in bridge fdb show command.
Signed-off-by: Minoura Makoto <minoura@valinux.co.jp>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
On reviewing the code I realized that GRE and UDP tunnels could cause a
kernel panic if we used GSO to segment a large UDP frame that was sent
through the tunnel with an outer checksum and hardware offloads were not
available.
In order to correct this we need to update the feature flags that are
passed to the skb_segment function so that in the event of UDP
fragmentation being requested for the inner header the segmentation
function will correctly generate the checksum for the payload if we cannot
segment the outer header.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When selecting an address in context of a VRF, the vrf master should be
preferred for address selection. If it isn't, the user has a hard time
getting the system to select to their preference - the code will pick
the address off the first in-VRF interface it can find, which on a
router could well be a non-routable address.
Signed-off-by: David Lamparter <equinox@diac24.net>
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
[dsa: Fixed comment style and removed extra blank link ]
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
David Lamparter noted a use case where the source address selection fails
to pick an address from a VRF interface - unnumbered interfaces.
Relevant commands from his script:
ip addr add 9.9.9.9/32 dev lo
ip link set lo up
ip link add name vrf0 type vrf table 101
ip rule add oif vrf0 table 101
ip rule add iif vrf0 table 101
ip link set vrf0 up
ip addr add 10.0.0.3/32 dev vrf0
ip link add name dummy2 type dummy
ip link set dummy2 master vrf0 up
--> note dummy2 has no address - unnumbered device
ip route add 10.2.2.2/32 dev dummy2 table 101
ip neigh add 10.2.2.2 dev dummy2 lladdr 02:00:00:00:00:02
tcpdump -ni dummy2 &
And using ping instead of his socat example:
$ ping -I vrf0 -c1 10.2.2.2
ping: Warning: source address might be selected on device other than vrf0.
PING 10.2.2.2 (10.2.2.2) from 9.9.9.9 vrf0: 56(84) bytes of data.
>From tcpdump:
12:57:29.449128 IP 9.9.9.9 > 10.2.2.2: ICMP echo request, id 2491, seq 1, length 64
Note the source address is from lo and is not a VRF local address. With
this patch:
$ ping -I vrf0 -c1 10.2.2.2
PING 10.2.2.2 (10.2.2.2) from 10.0.0.3 vrf0: 56(84) bytes of data.
>From tcpdump:
12:59:25.096426 IP 10.0.0.3 > 10.2.2.2: ICMP echo request, id 2113, seq 1, length 64
Now the source address comes from vrf0.
The ipv4 function for selecting source address takes a const argument.
Removing the const requires touching a lot of places, so instead
l3mdev_master_ifindex_rcu is changed to take a const argument and then
do the typecast to non-const as required by netdev_master_upper_dev_get_rcu.
This is similar to what l3mdev_fib_table_rcu does.
IPv6 for unnumbered interfaces appears to be selecting the addresses
properly.
Cc: David Lamparter <david@opensourcerouting.org>
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/sage/ceph-client
Pull Ceph fixes from Sage Weil:
"There are two small messenger bug fixes and a log spam regression fix"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/sage/ceph-client:
libceph: don't spam dmesg with stray reply warnings
libceph: use the right footer size when skipping a message
libceph: don't bail early from try_read() when skipping a message
|
|
This patch fixes the return value in a case which should never occur.
Instead returning "-EINVAL" we return LOWPAN_IPHC_DAM_00 which is
invalid on context based addresses. Also change the WARN_ON_ONCE to
WARN_ONCE which was suggested by Dan Carpenter.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Alexander Aring <aar@pengutronix.de>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
Pull nfsd bugfix from Bruce Fields:
"One fix for a bug that could cause a NULL write past the end of a
buffer in case of unusually long writes to some system interfaces used
by mountd and other nfs support utilities"
* tag 'nfsd-4.5-1' of git://linux-nfs.org/~bfields/linux:
sunrpc/cache: fix off-by-one in qword_get()
|
|
replaced by __ethtool_get_link_ksettings.
Signed-off-by: David Decotigny <decot@googlers.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: David Decotigny <decot@googlers.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: David Decotigny <decot@googlers.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: David Decotigny <decot@googlers.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch defines a new ETHTOOL_GLINKSETTINGS/SLINKSETTINGS API,
handled by the new get_link_ksettings/set_link_ksettings callbacks.
This API provides support for most legacy ethtool_cmd fields, adds
support for larger link mode masks (up to 4064 bits, variable length),
and removes ethtool_cmd deprecated
fields (transceiver/maxrxpkt/maxtxpkt).
This API is deprecating the legacy ETHTOOL_GSET/SSET API and provides
the following backward compatibility properties:
- legacy ethtool with legacy drivers: no change, still using the
get_settings/set_settings callbacks.
- legacy ethtool with new get/set_link_ksettings drivers: the new
driver callbacks are used, data internally converted to legacy
ethtool_cmd. ETHTOOL_GSET will return only the 1st 32b of each link
mode mask. ETHTOOL_SSET will fail if user tries to set the
ethtool_cmd deprecated fields to
non-0 (transceiver/maxrxpkt/maxtxpkt). A kernel warning is logged if
driver sets higher bits.
- future ethtool with legacy drivers: no change, still using the
get_settings/set_settings callbacks, internally converted to new data
structure. Deprecated fields (transceiver/maxrxpkt/maxtxpkt) will be
ignored and seen as 0 from user space. Note that that "future"
ethtool tool will not allow changes to these deprecated fields.
- future ethtool with new drivers: direct call to the new callbacks.
By "future" ethtool, what is meant is:
- query: first try ETHTOOL_GLINKSETTINGS, and revert to ETHTOOL_GSET if
fails
- set: query first and remember which of ETHTOOL_GLINKSETTINGS or
ETHTOOL_GSET was successful
+ if ETHTOOL_GLINKSETTINGS was successful, then change config with
ETHTOOL_SLINKSETTINGS. A failure there is final (do not try
ETHTOOL_SSET).
+ otherwise ETHTOOL_GSET was successful, change config with
ETHTOOL_SSET. A failure there is final (do not try
ETHTOOL_SLINKSETTINGS).
The interaction user/kernel via the new API requires a small
ETHTOOL_GLINKSETTINGS handshake first to agree on the length of the link
mode bitmaps. If kernel doesn't agree with user, it returns the bitmap
length it is expecting from user as a negative length (and cmd field is
0). When kernel and user agree, kernel returns valid info in all
fields (ie. link mode length > 0 and cmd is ETHTOOL_GLINKSETTINGS).
Data structure crossing user/kernel boundary is 32/64-bit
agnostic. Converted internally to a legal kernel bitmap.
The internal __ethtool_get_settings kernel helper will gradually be
replaced by __ethtool_get_link_ksettings by the time the first
"link_settings" drivers start to appear. So this patch doesn't change
it, it will be removed before it needs to be changed.
Signed-off-by: David Decotigny <decot@googlers.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch add the SO_CNX_ADVICE socket option (setsockopt only). The
purpose is to allow an application to give feedback to the kernel about
the quality of the network path for a connected socket. The value
argument indicates the type of quality report. For this initial patch
the only supported advice is a value of 1 which indicates "bad path,
please reroute"-- the action taken by the kernel is to call
dst_negative_advice which will attempt to choose a different ECMP route,
reset the TX hash for flow label and UDP source port in encapsulation,
etc.
This facility should be useful for connected UDP sockets where only the
application can provide any feedback about path quality. It could also
be useful for TCP applications that have additional knowledge about the
path outside of the normal TCP control loop.
Signed-off-by: Tom Herbert <tom@herbertland.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently, all ipv6 addresses are flushed when the interface is configured
down, including global, static addresses:
$ ip -6 addr show dev eth1
3: eth1: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 state UP qlen 1000
inet6 2100:1::2/120 scope global
valid_lft forever preferred_lft forever
inet6 fe80::e0:f9ff:fe79:34bd/64 scope link
valid_lft forever preferred_lft forever
$ ip link set dev eth1 down
$ ip -6 addr show dev eth1
<< nothing; all addresses have been flushed>>
Add a new sysctl to make this behavior optional. The new setting defaults to
flush all addresses to maintain backwards compatibility. When the set global
addresses with no expire times are not flushed on an admin down. The sysctl
is per-interface or system-wide for all interfaces
$ sysctl -w net.ipv6.conf.eth1.keep_addr_on_down=1
or
$ sysctl -w net.ipv6.conf.all.keep_addr_on_down=1
Will keep addresses on eth1 on an admin down.
$ ip -6 addr show dev eth1
3: eth1: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 state UP qlen 1000
inet6 2100:1::2/120 scope global
valid_lft forever preferred_lft forever
inet6 fe80::e0:f9ff:fe79:34bd/64 scope link
valid_lft forever preferred_lft forever
$ ip link set dev eth1 down
$ ip -6 addr show dev eth1
3: eth1: <BROADCAST,MULTICAST> mtu 1500 state DOWN qlen 1000
inet6 2100:1::2/120 scope global tentative
valid_lft forever preferred_lft forever
inet6 fe80::e0:f9ff:fe79:34bd/64 scope link tentative
valid_lft forever preferred_lft forever
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
