| Age | Commit message (Collapse) | Author |
|---|
|
AP may run out of BSS color after color collision
detection event from driver.
Disable BSS color collision detection if no free colors are
available based on bss color disabled bit sent as a part of
NL80211_ATTR_HE_BSS_COLOR attribute sent in
NL80211_CMD_SET_BEACON.
It can be reenabled once new color is available.
Signed-off-by: Lavanya Suresh <lavaks@codeaurora.org>
Signed-off-by: Rameshkumar Sundaram <quic_ramess@quicinc.com>
Link: https://lore.kernel.org/r/1649867295-7204-3-git-send-email-quic_ramess@quicinc.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
NL80211_ATTR_HE_BSS_COLOR attribute can be included in both
NL80211_CMD_START_AP and NL80211_CMD_SET_BEACON commands.
Move he_bss_color from cfg80211_ap_settings to cfg80211_beacon_data
and parse NL80211_ATTR_HE_BSS_COLOR as a part of nl80211_parse_beacon()
to have bss color settings parsed for both start ap and set beacon
commands.
Add a new flag he_bss_color_valid to indicate whether
NL80211_ATTR_HE_BSS_COLOR attribute is included.
Signed-off-by: Rameshkumar Sundaram <quic_ramess@quicinc.com>
Link: https://lore.kernel.org/r/1649867295-7204-2-git-send-email-quic_ramess@quicinc.com
[fix build ...]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
In IPv4 setting the "disable_policy" flag on a device means no policy
should be enforced for traffic originating from the device. This was
implemented by seting the DST_NOPOLICY flag in the dst based on the
originating device.
However, dsts are cached in nexthops regardless of the originating
devices, in which case, the DST_NOPOLICY flag value may be incorrect.
Consider the following setup:
+------------------------------+
| ROUTER |
+-------------+ | +-----------------+ |
| ipsec src |----|-|ipsec0 | |
+-------------+ | |disable_policy=0 | +----+ |
| +-----------------+ |eth1|-|-----
+-------------+ | +-----------------+ +----+ |
| noipsec src |----|-|eth0 | |
+-------------+ | |disable_policy=1 | |
| +-----------------+ |
+------------------------------+
Where ROUTER has a default route towards eth1.
dst entries for traffic arriving from eth0 would have DST_NOPOLICY
and would be cached and therefore can be reused by traffic originating
from ipsec0, skipping policy check.
Fix by setting a IPSKB_NOPOLICY flag in IPCB and observing it instead
of the DST in IN/FWD IPv4 policy checks.
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2")
Reported-by: Shmulik Ladkani <shmulik.ladkani@gmail.com>
Signed-off-by: Eyal Birger <eyal.birger@gmail.com>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
|
|
We currently track whether we're associated and which the
BSS is in the same variable (ifmgd->associated), but for
MLD we'll need to move the BSS pointer to be per link,
while the question whether we're associated or not is for
the whole interface.
Add ifmgd->assoc_bss that stores the pointer and change
ifmgd->associated to be just a bool, so the question of
whether we're associated can continue working after MLD
rework, without requiring changes, while the BSS pointer
will have to be changed/used checked per link.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
We don't need to copy this locally, we now only use the
variable to print before doing other things.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
We never use the bssid argument to ieee80211_sta_connection_lost()
so we might as well just remove it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
There's no need to look it up from the ifmgd->associated
BSS configuration, we already maintain a local copy since
commit b0140fda626e ("mac80211: mlme: save ssid info to
ieee80211_bss_conf while assoc").
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Since we always track the BSSID there when we get associated,
these are equivalent, but ifmgd->bssid saves a dereference and
thus makes the code a bit smaller, and more readable.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
This code is tightly coupled to the sdata->u.mgd data
structure, so there's no reason for it to be in utils.
Move it to mlme.c.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Ping-Ke's previous patch adjusted the CCMP AAD construction
to properly take the order bit into account, but failed to
update the (identical) GCMP AAD construction as well.
Unify the AAD construction between the two cases.
Reported-by: Jouni Malinen <j@w1.fi>
Link: https://lore.kernel.org/r/20220506105150.51d66e2a6f3c.I65f12be82c112365169e8a9f48c7a71300e814b9@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
If the PM closes a fully established MPJ subflow or the subflow
creation errors out in it's early stage the subflows counter is
not bumped accordingly.
This change adds the missing accounting, additionally taking care
of updating accordingly the 'accept_subflow' flag.
Fixes: a88c9e496937 ("mptcp: do not block subflows creation on errors")
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Pull NFS client bugfixes from Trond Myklebust:
"One more pull request. There was a bug in the fix to ensure that gss-
proxy continues to work correctly after we fixed the AF_LOCAL socket
leak in the RPC code. This therefore reverts that broken patch, and
replaces it with one that works correctly.
Stable fixes:
- SUNRPC: Ensure that the gssproxy client can start in a connected
state
Bugfixes:
- Revert "SUNRPC: Ensure gss-proxy connects on setup"
- nfs: fix broken handling of the softreval mount option"
* tag 'nfs-for-5.18-4' of git://git.linux-nfs.org/projects/trondmy/linux-nfs:
nfs: fix broken handling of the softreval mount option
SUNRPC: Ensure that the gssproxy client can start in a connected state
Revert "SUNRPC: Ensure gss-proxy connects on setup"
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/klassert/ipsec-next
Steffen Klassert says:
====================
pull request (net-next): ipsec-next 2022-05-13
1) Cleanups for the code behind the XFRM offload API. This is a
preparation for the extension of the API for policy offload.
From Leon Romanovsky.
* 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/klassert/ipsec-next:
xfrm: drop not needed flags variable in XFRM offload struct
net/mlx5e: Use XFRM state direction instead of flags
netdevsim: rely on XFRM state direction instead of flags
ixgbe: propagate XFRM offload state direction instead of flags
xfrm: store and rely on direction to construct offload flags
xfrm: rename xfrm_state_offload struct to allow reuse
xfrm: delete not used number of external headers
xfrm: free not used XFRM_ESP_NO_TRAILER flag
====================
Link: https://lore.kernel.org/r/20220513151218.4010119-1-steffen.klassert@secunet.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The checksum is optional for UDP packets. However nf_reject would
previously require a valid checksum to elicit a response such as
ICMP_DEST_UNREACH.
Add some logic to nf_reject_verify_csum to determine if a UDP packet has
a zero checksum and should therefore not be verified.
Signed-off-by: Kevin Mitchell <kevmitch@arista.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
When creating a flow table entry, the reverse route is looked
up based on the current packet.
There can be scenarios where the user creates a custom ip rule
to route the traffic differently.
In order to support those scenarios, the lookup needs to add
more information based on the current packet.
The patch adds multiple new information to the route lookup.
Signed-off-by: Sven Auhagen <sven.auhagen@voleatech.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
This adds the new nf_conntrack_events=2 mode and makes it the
default.
This leverages the earlier flag in struct net to allow to avoid
the event extension as long as no event listener is active in
the namespace.
This avoids, for most cases, allocation of ct->ext area.
A followup patch will take further advantage of this by avoiding
calls down into the event framework if the extension isn't present.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
Only called when new ct is allocated or the extension isn't present.
This function will be extended, place this in the conntrack module
instead of inlining.
The callers already depend on nf_conntrack module.
Return value is changed to bool, noone used the returned pointer.
Make sure that the core drops the newly allocated conntrack
if the extension is requested but can't be added.
This makes it necessary to ifdef the section, as the stub
always returns false we'd drop every new conntrack if the
the ecache extension is disabled in kconfig.
Add from data path (xt_CT, nft_ct) is unchanged.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
At this time, every new conntrack gets the 'event cache extension'
enabled for it.
This is because the 'net.netfilter.nf_conntrack_events' sysctl defaults
to 1.
Changing the default to 0 means that commands that rely on the event
notification extension, e.g. 'conntrack -E' or conntrackd, stop working.
We COULD detect if there is a listener by means of
'nfnetlink_has_listeners()' and only add the extension if this is true.
The downside is a dependency from conntrack module to nfnetlink module.
This adds a different way: inc/dec a counter whenever a ctnetlink group
is being (un)subscribed and toggle a flag in struct net.
Next patches will take advantage of this and will only add the event
extension if the flag is set.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
This patch adds a structure to collect all the context data that is
passed to the cleanup iterator.
struct nf_ct_iter_data {
struct net *net;
void *data;
u32 portid;
int report;
};
There is a netns field that allows to clean up conntrack entries
specifically owned by the specified netns.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
Now that the conntrack entry isn't placed on the pcpu list anymore the
bh only needs to be disabled in the 'expectation present' case.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
It has no function anymore and can be removed.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
Its not needed anymore:
A. If entry is totally new, then the rcu-protected resource
must already have been removed from global visibility before call
to nf_ct_iterate_destroy.
B. If entry was allocated before, but is not yet in the hash table
(uncofirmed case), genid gets incremented and synchronize_rcu() call
makes sure access has completed.
C. Next attempt to peek at extension area will fail for unconfirmed
conntracks, because ext->genid != genid.
D. Conntracks in the hash are iterated as before.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
Increment the extid on module removal; this makes sure that even
in extreme cases any old uncofirmed entry that happened to be kept
e.g. on nfnetlink_queue list will not trip over a stale timeout
reference.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
Multiple netfilter extensions store pointers to external data
in their extension area struct.
Examples:
1. Timeout policies
2. Connection tracking helpers.
No references are taken for these.
When a helper or timeout policy is removed, the conntrack table gets
traversed and affected extensions are cleared.
Conntrack entries not yet in the hashtable are referenced via a special
list, the unconfirmed list.
On removal of a policy or connection tracking helper, the unconfirmed
list gets traversed an all entries are marked as dying, this prevents
them from getting committed to the table at insertion time: core checks
for dying bit, if set, the conntrack entry gets destroyed at confirm
time.
The disadvantage is that each new conntrack has to be added to the percpu
unconfirmed list, and each insertion needs to remove it from this list.
The list is only ever needed when a policy or helper is removed -- a rare
occurrence.
Add a generation ID count: Instead of adding to the list and then
traversing that list on policy/helper removal, increment a counter
that is stored in the extension area.
For unconfirmed conntracks, the extension has the genid valid at ct
allocation time.
Removal of a helper/policy etc. increments the counter.
At confirmation time, validate that ext->genid == global_id.
If the stored number is not the same, do not allow the conntrack
insertion, just like as if a confirmed-list traversal would have flagged
the entry as dying.
After insertion, the genid is no longer relevant (conntrack entries
are now reachable via the conntrack table iterators and is set to 0.
This allows removal of the percpu unconfirmed list.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
This helper tags connections not yet in the conntrack table as
dying. These nf_conn entries will be dropped instead when the
core attempts to insert them from the input or postrouting
'confirm' hook.
After the previous change, the entries get unlinked from the
list earlier, so that by the time the actual exit hook runs,
new connections no longer have a timeout policy assigned.
Its enough to walk the hashtable instead.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
Make it so netns pre_exit unlinks the objects from the pernet list, so
they cannot be found anymore.
netns core issues a synchronize_rcu() before calling the exit hooks so
any the time the exit hooks run unconfirmed nf_conn entries have been
free'd or they have been committed to the hashtable.
The exit hook still tags unconfirmed entries as dying, this can
now be removed in a followup change.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
Its no longer needed. Entries that need event redelivery are placed
on the new pernet dying list.
The advantage is that there is no need to take additional spinlock on
conntrack removal unless event redelivery failed or the conntrack entry
was never added to the table in the first place (confirmed bit not set).
The IPS_CONFIRMED bit now needs to be set as soon as the entry has been
unlinked from the unconfirmed list, else the destroy function may
attempt to unlink it a second time.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
The new pernet dying list includes conntrack entries that await
delivery of the 'destroy' event via ctnetlink.
The old percpu dying list will be removed soon.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
This disentangles event redelivery and the percpu dying list.
Because entries are now stored on a dedicated list, all
entries are in NFCT_ECACHE_DESTROY_FAIL state and all entries
still have confirmed bit set -- the reference count is at least 1.
The 'struct net' back-pointer can be removed as well.
The pcpu dying list will be removed eventually, it has no functionality.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
This reverts commits:
0dad4087a86a2cbe177404dc73f18ada26a2c390 ("tcp/dccp: get rid of inet_twsk_purge()")
d507204d3c5cc57d9a8bdf0a477615bb59ea1611 ("tcp/dccp: add tw->tw_bslot")
As Leonard pointed out, a newly allocated netns can happen
to reuse a freed 'struct net'.
While TCP TW timers were covered by my patches, other things were not:
1) Lookups in rx path (INET_MATCH() and INET6_MATCH()), as they look
at 4-tuple plus the 'struct net' pointer.
2) /proc/net/tcp[6] and inet_diag, same reason.
3) hashinfo->bhash[], same reason.
Fixing all this seems risky, lets instead revert.
In the future, we might have a per netns tcp hash table, or
a per netns list of timewait sockets...
Fixes: 0dad4087a86a ("tcp/dccp: get rid of inet_twsk_purge()")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Leonard Crestez <cdleonard@gmail.com>
Tested-by: Leonard Crestez <cdleonard@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When suspending the passive scanning _must_ have its filter_policy set
to 0x01 to use the accept list otherwise _any_ advertise report would
end up waking up the system.
In order to fix the filter_policy the code now checks for
hdev->suspended && HCI_CONN_FLAG_REMOTE_WAKEUP
first, since the MGMT_OP_SET_DEVICE_FLAGS will reject any attempt to
set HCI_CONN_FLAG_REMOTE_WAKEUP when it cannot be programmed in the
acceptlist, so it can return success causing the proper filter_policy
to be used.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=215768
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
HCI_CONN_FLAG_REMOTE_WAKEUP can only be set if device can be programmed
in the allowlist which in case of device using RPA requires LL Privacy
support to be enabled.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=215768
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
INET_MATCH() runs without holding a lock on the socket.
We probably need to annotate most reads.
This patch makes INET_MATCH() an inline function
to ease our changes.
v2:
We remove the 32bit version of it, as modern compilers
should generate the same code really, no need to
try to be smarter.
Also make 'struct net *net' the first argument.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Move power_on work cancel to hci_dev_close_sync to ensure that power_on
work is canceled after HCI interface down, power off, rfkill, etc.
For example, if
hciconfig hci0 down
is done early enough during boot, it may run before power_on work.
Then, power_on work will actually bring up interface despite above
hciconfig command.
Signed-off-by: Vasyl Vavrychuk <vasyl.vavrychuk@opensynergy.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
Concurrent operations from events on le_{accept,resolv}_list are
currently unprotected by hdev->lock.
Most existing code do already protect the lists with that lock.
This can be observed in hci_debugfs and hci_sync.
Add the protection for these events too.
Fixes: b950aa88638c ("Bluetooth: Add definitions and track LE resolve list modification")
Fixes: 0f36b589e4ee ("Bluetooth: Track LE white list modification via HCI commands")
Signed-off-by: Niels Dossche <dossche.niels@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
All accesses (both reads and modifications) to
hdev->{accept,reject}_list are protected by hdev lock,
except the ones in hci_conn_request_evt. This can cause a race
condition in the form of a list corruption.
The solution is to protect these lists in hci_conn_request_evt as well.
I was unable to find the exact commit that introduced the issue for the
reject list, I was only able to find it for the accept list.
Fixes: a55bd29d5227 ("Bluetooth: Add white list lookup for incoming connection requests")
Signed-off-by: Niels Dossche <dossche.niels@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
hci_is_adv_monitoring's function documentation states that it must be
called under the hdev lock. Paths that leads to an unlocked call are:
discov_update => start_discovery => interleaved_discov => active_scan
and: discov_update => start_discovery => active_scan
The solution is to take the lock in active_scan during the duration of
the call to hci_is_adv_monitoring.
Fixes: c32d624640fd ("Bluetooth: disable filter dup when scan for adv monitor")
Signed-off-by: Niels Dossche <dossche.niels@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
This prints warnings for controllers setting broken quirks to increase
their visibility and warn about broken controllers firmware that
probably needs updates to behave properly.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
This adds HCI_QUIRK_BROKEN_ENHANCED_SETUP_SYNC_CONN quirk which can be
used to mark HCI_Enhanced_Setup_Synchronous_Connection as broken even
if its support command bit are set since some controller report it as
supported but the command don't work properly with some configurations
(e.g. BT_VOICE_TRANSPARENT/mSBC).
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
Small change to add new commands to tail of the list, and find/remove them
from the head of the list.
Signed-off-by: Brian Gix <brian.gix@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
Connecting the same socket twice consecutively in sco_sock_connect()
could lead to a race condition where two sco_conn objects are created
but only one is associated with the socket. If the socket is closed
before the SCO connection is established, the timer associated with the
dangling sco_conn object won't be canceled. As the sock object is being
freed, the use-after-free problem happens when the timer callback
function sco_sock_timeout() accesses the socket. Here's the call trace:
dump_stack+0x107/0x163
? refcount_inc+0x1c/
print_address_description.constprop.0+0x1c/0x47e
? refcount_inc+0x1c/0x7b
kasan_report+0x13a/0x173
? refcount_inc+0x1c/0x7b
check_memory_region+0x132/0x139
refcount_inc+0x1c/0x7b
sco_sock_timeout+0xb2/0x1ba
process_one_work+0x739/0xbd1
? cancel_delayed_work+0x13f/0x13f
? __raw_spin_lock_init+0xf0/0xf0
? to_kthread+0x59/0x85
worker_thread+0x593/0x70e
kthread+0x346/0x35a
? drain_workqueue+0x31a/0x31a
? kthread_bind+0x4b/0x4b
ret_from_fork+0x1f/0x30
Link: https://syzkaller.appspot.com/bug?extid=2bef95d3ab4daa10155b
Reported-by: syzbot+2bef95d3ab4daa10155b@syzkaller.appspotmail.com
Fixes: e1dee2c1de2b ("Bluetooth: fix repeated calls to sco_sock_kill")
Signed-off-by: Ying Hsu <yinghsu@chromium.org>
Reviewed-by: Joseph Hwang <josephsih@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
Currently If use page pool allocation stats to analysis a RX performance
degradation problem. These stats only count for pages allocate from
page_pool_alloc_pages. But nic drivers such as hns3 use
page_pool_dev_alloc_frag to allocate pages, so page stats in this API
should also be counted.
Signed-off-by: Jie Wang <wangjie125@huawei.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The listen sk is currently stored in two hash tables,
listening_hash (hashed by port) and lhash2 (hashed by port and address).
After commit 0ee58dad5b06 ("net: tcp6: prefer listeners bound to an address")
and commit d9fbc7f6431f ("net: tcp: prefer listeners bound to an address"),
the TCP-SYN lookup fast path does not use listening_hash.
The commit 05c0b35709c5 ("tcp: seq_file: Replace listening_hash with lhash2")
also moved the seq_file (/proc/net/tcp) iteration usage from
listening_hash to lhash2.
There are still a few listening_hash usages left.
One of them is inet_reuseport_add_sock() which uses the listening_hash
to search a listen sk during the listen() system call. This turns
out to be very slow on use cases that listen on many different
VIPs at a popular port (e.g. 443). [ On top of the slowness in
adding to the tail in the IPv6 case ]. The latter patch has a
selftest to demonstrate this case.
This patch takes this chance to move all remaining listening_hash
usages to lhash2 and then retire listening_hash.
Since most changes need to be done together, it is hard to cut
the listening_hash to lhash2 switch into small patches. The
changes in this patch is highlighted here for the review
purpose.
1. Because of the listening_hash removal, lhash2 can use the
sk->sk_nulls_node instead of the icsk->icsk_listen_portaddr_node.
This will also keep the sk_unhashed() check to work as is
after stop adding sk to listening_hash.
The union is removed from inet_listen_hashbucket because
only nulls_head is needed.
2. icsk->icsk_listen_portaddr_node and its helpers are removed.
3. The current lhash2 users needs to iterate with sk_nulls_node
instead of icsk_listen_portaddr_node.
One case is in the inet[6]_lhash2_lookup().
Another case is the seq_file iterator in tcp_ipv4.c.
One thing to note is sk_nulls_next() is needed
because the old inet_lhash2_for_each_icsk_continue()
does a "next" first before iterating.
4. Move the remaining listening_hash usage to lhash2
inet_reuseport_add_sock() which this series is
trying to improve.
inet_diag.c and mptcp_diag.c are the final two
remaining use cases and is moved to lhash2 now also.
Signed-off-by: Martin KaFai Lau <kafai@fb.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
This patch folds lhash2 related functions into __inet_hash and
inet_unhash. This will make the removal of the listening_hash
in a latter patch easier to review.
First, this patch folds inet_hash2 into __inet_hash.
For unhash, the current call sequence is like
inet_unhash() => __inet_unhash() => inet_unhash2().
The specific testing cases in __inet_unhash() are mostly related
to TCP_LISTEN sk and its caller inet_unhash() already has
the TCP_LISTEN test, so this patch folds both __inet_unhash() and
inet_unhash2() into inet_unhash().
Note that all listening_hash users also have lhash2 initialized,
so the !h->lhash2 check is no longer needed.
Signed-off-by: Martin KaFai Lau <kafai@fb.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
After commit 0ee58dad5b06 ("net: tcp6: prefer listeners bound to an address")
and commit d9fbc7f6431f ("net: tcp: prefer listeners bound to an address"),
the count is no longer used. This patch removes it.
Signed-off-by: Martin KaFai Lau <kafai@fb.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
DSA has not supported (and probably will not support in the future
either) independent tagging protocols per CPU port.
Different switch drivers have different requirements, some may need to
replicate some settings for each CPU port, some may need to apply some
settings on a single CPU port, while some may have to configure some
global settings and then some per-CPU-port settings.
In any case, the current model where DSA calls ->change_tag_protocol for
each CPU port turns out to be impractical for drivers where there are
global things to be done. For example, felix calls dsa_tag_8021q_register(),
which makes no sense per CPU port, so it suppresses the second call.
Let drivers deal with replication towards all CPU ports, and remove the
CPU port argument from the function prototype.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Acked-by: Luiz Angelo Daros de Luca <luizluca@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
At the time - commit 7569459a52c9 ("net: dsa: manage flooding on the CPU
ports") - not introducing a dedicated switch callback for host flooding
made sense, because for the only user, the felix driver, there was
nothing different to do for the CPU port than set the flood flags on the
CPU port just like on any other bridge port.
There are 2 reasons why this approach is not good enough, however.
(1) Other drivers, like sja1105, support configuring flooding as a
function of {ingress port, egress port}, whereas the DSA
->port_bridge_flags() function only operates on an egress port.
So with that driver we'd have useless host flooding from user ports
which don't need it.
(2) Even with the felix driver, support for multiple CPU ports makes it
difficult to piggyback on ->port_bridge_flags(). The way in which
the felix driver is going to support host-filtered addresses with
multiple CPU ports is that it will direct these addresses towards
both CPU ports (in a sort of multicast fashion), then restrict the
forwarding to only one of the two using the forwarding masks.
Consequently, flooding will also be enabled towards both CPU ports.
However, ->port_bridge_flags() gets passed the index of a single CPU
port, and that leaves the flood settings out of sync between the 2
CPU ports.
This is to say, it's better to have a specific driver method for host
flooding, which takes the user port as argument. This solves problem (1)
by allowing the driver to do different things for different user ports,
and problem (2) by abstracting the operation and letting the driver do
whatever, rather than explicitly making the DSA core point to the CPU
port it thinks needs to be touched.
This new method also creates a problem, which is that cross-chip setups
are not handled. However I don't have hardware right now where I can
test what is the proper thing to do, and there isn't hardware compatible
with multi-switch trees that supports host flooding. So it remains a
problem to be tackled in the future.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The BUGS section looks quite dated, the registration
is under rtnl lock. Remove some obvious information
while at it.
Link: https://lore.kernel.org/r/20220511190720.1401356-1-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
No conflicts.
Build issue in drivers/net/ethernet/sfc/ptp.c
54fccfdd7c66 ("sfc: efx_default_channel_type APIs can be static")
49e6123c65da ("net: sfc: fix memory leak due to ptp channel")
https://lore.kernel.org/all/20220510130556.52598fe2@canb.auug.org.au/
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net
Pull networking fixes from Jakub Kicinski:
"Including fixes from wireless, and bluetooth.
No outstanding fires.
Current release - regressions:
- eth: atlantic: always deep reset on pm op, fix null-deref
Current release - new code bugs:
- rds: use maybe_get_net() when acquiring refcount on TCP sockets
[refinement of a previous fix]
- eth: ocelot: mark traps with a bool instead of guessing type based
on list membership
Previous releases - regressions:
- net: fix skipping features in for_each_netdev_feature()
- phy: micrel: fix null-derefs on suspend/resume and probe
- bcmgenet: check for Wake-on-LAN interrupt probe deferral
Previous releases - always broken:
- ipv4: drop dst in multicast routing path, prevent leaks
- ping: fix address binding wrt vrf
- net: fix wrong network header length when BPF protocol translation
is used on skbs with a fraglist
- bluetooth: fix the creation of hdev->name
- rfkill: uapi: fix RFKILL_IOCTL_MAX_SIZE ioctl request definition
- wifi: iwlwifi: iwl-dbg: use del_timer_sync() before freeing
- wifi: ath11k: reduce the wait time of 11d scan and hw scan while
adding an interface
- mac80211: fix rx reordering with non explicit / psmp ack policy
- mac80211: reset MBSSID parameters upon connection
- nl80211: fix races in nl80211_set_tx_bitrate_mask()
- tls: fix context leak on tls_device_down
- sched: act_pedit: really ensure the skb is writable
- batman-adv: don't skb_split skbuffs with frag_list
- eth: ocelot: fix various issues with TC actions (null-deref; bad
stats; ineffective drops; ineffective filter removal)"
* tag 'net-5.18-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (61 commits)
tls: Fix context leak on tls_device_down
net: sfc: ef10: fix memory leak in efx_ef10_mtd_probe()
net/smc: non blocking recvmsg() return -EAGAIN when no data and signal_pending
net: dsa: bcm_sf2: Fix Wake-on-LAN with mac_link_down()
mlxsw: Avoid warning during ip6gre device removal
net: bcmgenet: Check for Wake-on-LAN interrupt probe deferral
net: ethernet: mediatek: ppe: fix wrong size passed to memset()
Bluetooth: Fix the creation of hdev->name
i40e: i40e_main: fix a missing check on list iterator
net/sched: act_pedit: really ensure the skb is writable
s390/lcs: fix variable dereferenced before check
s390/ctcm: fix potential memory leak
s390/ctcm: fix variable dereferenced before check
net: atlantic: verify hw_head_ lies within TX buffer ring
net: atlantic: add check for MAX_SKB_FRAGS
net: atlantic: reduce scope of is_rsc_complete
net: atlantic: fix "frag[0] not initialized"
net: stmmac: fix missing pci_disable_device() on error in stmmac_pci_probe()
net: phy: micrel: Fix incorrect variable type in micrel
decnet: Use container_of() for struct dn_neigh casts
...
|
