| Age | Commit message (Collapse) | Author |
|---|
|
Introducing a new feature that the driver can use to
indicate the driver/firmware supports configuration of BSS
selection criteria upon CONNECT command. This can be useful
when multiple BSS-es are found belonging to the same ESS,
ie. Infra-BSS with same SSID. The criteria can then be used to
offload selection of a preferred BSS.
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Lei Zhang <leizh@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
[move wiphy support check into parse_bss_select()]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Some devices, like iwlwifi, have RSS queues. This may cause a
situation where a disassociation is handled in control path and
results in station removal while there are prior RX frames
that were still not processed in other queues. When they will
be processed the station will be gone, and the frames will be
dropped.
Add a synchronization interface to avoid that. When driver returns
from the synchronization mac80211 may remove the station.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
In the time since the mesh path table was implemented as an
RCU-traversable, dynamically growing hash table, a generic RCU
hashtable implementation was added to the kernel.
Switch the mesh path table over to rhashtable to remove some code
and also gain some features like automatic shrinking.
Cc: Thomas Graf <tgraf@suug.ch>
Cc: netdev@vger.kernel.org
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
In certain cases, the 802.11 mesh pathtable code wants to
iterate over all of the entries in the forwarding table from
the receive path, which is inside an RCU read-side critical
section. Enable walks inside atomic sections by allowing
GFP_ATOMIC allocations for the walker state.
Change all existing callsites to pass in GFP_KERNEL.
Acked-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: Bob Copeland <me@bobcopeland.com>
[also adjust gfs2/glock.c and rhashtable tests]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
The mesh path table uses a struct mesh_node in its hlists in
order to support a resizable hash table: the mesh_node provides
an indirection to the actual mesh path so that two different
bucket lists can point to the same path entry.
However, for the known gates list, we don't need this indirection
because there is ever only one list. So we can just embed the
hlist_node in the mesh path itself, which simplifies things a bit
and saves a linear search whenever we need to find an item in
the list.
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Remove duplicate code to allocate and initialize a mesh
path or mesh proxy path.
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Now that the sdata pointer is the same for all entries of a
path table, hashing it is pointless, so hash only the address.
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
The mesh path and mesh gate hashtables are global, containing
all of the mpaths for every mesh interface, but the paths are
all tied logically to a single interface. The common case is
just a single mesh interface, so optimize for that by moving
the global hashtable into the per-interface struct.
Doing so allows us to drop sdata pointer comparisons inside
the lookups and also saves a few bytes of BSS and data.
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
If the cfg80211 scan trigger operation specifies a single BSSID, use
that value instead of the wildcard BSSID in the Probe Request frames.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
This allows scans for a specific BSSID to be optimized by the user space
application by requesting the driver to set the Probe Request frame
BSSID field (Address 3) to the specified BSSID instead of the wildcard
BSSID. This prevents other APs from replying which reduces airtime need
and latency in getting the response from the target AP through.
This is an optimization and as such, it is acceptable for some of the
drivers not to support the mechanism. If not supported, the wildcard
BSSID will be used and more responses may be received.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
The min_def chanctx is affected not only by the current chandef, but
sometimes also by other stations on the vif. There's a valid scenario
where a TDLS peer can widen its BW, thereby causing the min_def
to increase.
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
The previous approach simply ignored chandef restrictions when calculating
the appropriate peer BW for a WIDER_BW peer. This could result in a
regulatory violation if both peers indicated 80MHz support, but the
regdomain forbade it.
Change the approach to setting a WIDER_BW peer's BW. Don't exempt it from
the chandef width at first. If during TDLS negotiation the chandef width
is upgraded, update the peer's BW to match.
Fixes: 0fabfaafec3a ("mac80211: upgrade BW of TDLS peers when possible")
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Even if the current chandef width is equal to the station's max-BW, it
doesn't mean it's a valid width for TDLS. Make sure to always check
regulatory constraints in these cases.
Fixes: 0fabfaafec3a ("mac80211: upgrade BW of TDLS peers when possible")
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Buffered multicast frames must be passed to the driver directly via
drv_tx instead of going through the txq, otherwise they cannot easily be
scheduled to be sent after DTIM.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
When HW crypto is used, there's no need for the CCMP/GCMP MIC to
be available to mac80211, and the hardware might have removed it
already after checking. The MIC is also useless to have when the
frame is already decrypted, so allow indicating that it's not
present.
Since we are running out of bits in mac80211_rx_flags, make
the flags field a u64.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
This was requested by Android, and the appropriate cfg80211 API
had been added by Dmitry. Support it in mac80211, allowing drivers
to provide the timestamp.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Add VHT radiotap parsing support to ieee80211_parse_tx_radiotap().
That capability has been tested using a d-link dir-860l rev b1 running
OpenWrt trunk and mt76 driver
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi83@gmail.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Using a switch to handle different ev.op values in rfkill_fop_write()
makes the code easier to extend, as out-of-range values can always be
handled by the default case.
Signed-off-by: João Paulo Rechi Vita <jprvita@endlessm.com>
[roll in fix for RFKILL_OP_CHANGE from Jouni]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
If register_netdevice_notifier() fails (which in practice it can't
right now), we should call unregister_pernet_subsys(). Do that.
Reported-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Attackers like to use SYNFLOOD targeting one 5-tuple, as they
hit a single RX queue (and cpu) on the victim.
If they use random sequence numbers in their SYN, we detect
they do not match the expected window and send back an ACK.
This patch adds a rate limitation, so that the effect of such
attacks is limited to ingress only.
We roughly double our ability to absorb such attacks.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Willem de Bruijn <willemb@google.com>
Cc: Neal Cardwell <ncardwell@google.com>
Cc: Maciej Żenczykowski <maze@google.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
TCP uses per cpu 'sockets' to send some packets :
- RST packets ( tcp_v4_send_reset()) )
- ACK packets for SYN_RECV and TIMEWAIT sockets
By setting SOCK_USE_WRITE_QUEUE flag, we tell sock_wfree()
to not call sk_write_space() since these internal sockets
do not care.
This gives a small performance improvement, merely by allowing
cpu to properly predict the sock_wfree() conditional branch,
and avoiding one atomic operation.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Goal: packets dropped by a listener are accounted for.
This adds tcp_listendrop() helper, and clears sk_drops in sk_clone_lock()
so that children do not inherit their parent drop count.
Note that we no longer increment LINUX_MIB_LISTENDROPS counter when
sending a SYNCOOKIE, since the SYN packet generated a SYNACK.
We already have a separate LINUX_MIB_SYNCOOKIESSENT
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Now ss can report sk_drops, we can instruct TCP to increment
this per socket counter when it drops an incoming frame, to refine
monitoring and debugging.
Following patch takes care of listeners drops.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Reporting sk_drops to user space was available for UDP
sockets using /proc interface.
Add this to sock_diag, so that we can have the same information
available to ss users, and we'll be able to add sk_drops
indications for TCP sockets as well.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When a SYNFLOOD targets a non SO_REUSEPORT listener, multiple
cpus contend on sk->sk_refcnt and sk->sk_wmem_alloc changes.
By letting listeners use SOCK_RCU_FREE infrastructure,
we can relax TCP_LISTEN lookup rules and avoid touching sk_refcnt
Note that we still use SLAB_DESTROY_BY_RCU rules for other sockets,
only listeners are impacted by this change.
Peak performance under SYNFLOOD is increased by ~33% :
On my test machine, I could process 3.2 Mpps instead of 2.4 Mpps
Most consuming functions are now skb_set_owner_w() and sock_wfree()
contending on sk->sk_wmem_alloc when cooking SYNACK and freeing them.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
RX packet processing holds rcu_read_lock(), so we can remove
pairs of rcu_read_lock()/rcu_read_unlock() in lookup functions
if inet_diag also holds rcu before calling them.
This is needed anyway as __inet_lookup_listener() and
inet6_lookup_listener() will soon no longer increment
refcount on the found listener.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Since linux 2.6.29, lookups only use rcu locking.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Tom Herbert would like not touching UDP socket refcnt for encapsulated
traffic. For this to happen, we need to use normal RCU rules, with a grace
period before freeing a socket. UDP sockets are not short lived in the
high usage case, so the added cost of call_rcu() should not be a concern.
This actually removes a lot of complexity in UDP stack.
Multicast receives no longer need to hold a bucket spinlock.
Note that ip early demux still needs to take a reference on the socket.
Same remark for functions used by xt_socket and xt_PROXY netfilter modules,
but this might be changed later.
Performance for a single UDP socket receiving flood traffic from
many RX queues/cpus.
Simple udp_rx using simple recvfrom() loop :
438 kpps instead of 374 kpps : 17 % increase of the peak rate.
v2: Addressed Willem de Bruijn feedback in multicast handling
- keep early demux break in __udp4_lib_demux_lookup()
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Tom Herbert <tom@herbertland.com>
Cc: Willem de Bruijn <willemb@google.com>
Tested-by: Tom Herbert <tom@herbertland.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We want a generic way to insert an RCU grace period before socket
freeing for cases where RCU_SLAB_DESTROY_BY_RCU is adding too
much overhead.
SLAB_DESTROY_BY_RCU strict rules force us to take a reference
on the socket sk_refcnt, and it is a performance problem for UDP
encapsulation, or TCP synflood behavior, as many CPUs might
attempt the atomic operations on a shared sk_refcnt
UDP sockets and TCP listeners can set SOCK_RCU_FREE so that their
lookup can use traditional RCU rules, without refcount changes.
They can set the flag only once hashed and visible by other cpus.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Tom Herbert <tom@herbertland.com>
Tested-by: Tom Herbert <tom@herbertland.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This fixes the incorrect variable assignment on error path in
br_sysfs_addbr for when the call to kobject_create_and_add
fails to assign the value of -EINVAL to the returned variable of
err rather then incorrectly return zero making callers think this
function has succeededed due to the previous assignment being
assigned zero when assigning it the successful return value of
the call to sysfs_create_group which is zero.
Signed-off-by: Bastien Philbert <bastienphilbert@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
pskb_may_pull() can change skb->data, so we have to load ptr/optr at the
right place.
Signed-off-by: Haishuang Yan <yanhaishuang@cmss.chinamobile.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
pskb_may_pull() can change skb->data, so we have to load ptr/optr at the
right place.
Signed-off-by: Haishuang Yan <yanhaishuang@cmss.chinamobile.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently, SOL_TIMESTAMPING can only be enabled using setsockopt.
This is very costly when users want to sample writes to gather
tx timestamps.
Add support for enabling SO_TIMESTAMPING via control messages by
using tsflags added in `struct sockcm_cookie` (added in the previous
patches in this series) to set the tx_flags of the last skb created in
a sendmsg. With this patch, the timestamp recording bits in tx_flags
of the skbuff is overridden if SO_TIMESTAMPING is passed in a cmsg.
Please note that this is only effective for overriding the recording
timestamps flags. Users should enable timestamp reporting (e.g.,
SOF_TIMESTAMPING_SOFTWARE | SOF_TIMESTAMPING_OPT_ID) using
socket options and then should ask for SOF_TIMESTAMPING_TX_*
using control messages per sendmsg to sample timestamps for each
write.
Signed-off-by: Soheil Hassas Yeganeh <soheil@google.com>
Acked-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Process socket-level control messages by invoking
__sock_cmsg_send in ip6_datagram_send_ctl for control messages on
the SOL_SOCKET layer.
This makes sure whenever ip6_datagram_send_ctl is called for
udp and raw, we also process socket-level control messages.
This is a bit uglier than IPv4, since IPv6 does not have
something like ipcm_cookie. Perhaps we can later create
a control message cookie for IPv6?
Note that this commit interprets new control messages that
were ignored before. As such, this commit does not change
the behavior of IPv6 control messages.
Signed-off-by: Soheil Hassas Yeganeh <soheil@google.com>
Acked-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Process socket-level control messages by invoking
__sock_cmsg_send in ip_cmsg_send for control messages on
the SOL_SOCKET layer.
This makes sure whenever ip_cmsg_send is called in udp, icmp,
and raw, we also process socket-level control messages.
Note that this commit interprets new control messages that
were ignored before. As such, this commit does not change
the behavior of IPv4 control messages.
Signed-off-by: Soheil Hassas Yeganeh <soheil@google.com>
Acked-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Accept SO_TIMESTAMPING in control messages of the SOL_SOCKET level
as a basis to accept timestamping requests per write.
This implementation only accepts TX recording flags (i.e.,
SOF_TIMESTAMPING_TX_HARDWARE, SOF_TIMESTAMPING_TX_SOFTWARE,
SOF_TIMESTAMPING_TX_SCHED, and SOF_TIMESTAMPING_TX_ACK) in
control messages. Users need to set reporting flags (e.g.,
SOF_TIMESTAMPING_OPT_ID) per socket via socket options.
This commit adds a tsflags field in sockcm_cookie which is
set in __sock_cmsg_send. It only override the SOF_TIMESTAMPING_TX_*
bits in sockcm_cookie.tsflags allowing the control message
to override the recording behavior per write, yet maintaining
the value of other flags.
This patch implements validating the control message and setting
tsflags in struct sockcm_cookie. Next commits in this series will
actually implement timestamping per write for different protocols.
Signed-off-by: Soheil Hassas Yeganeh <soheil@google.com>
Acked-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently, to avoid a cache line miss for accessing skb_shinfo,
tcp_ack_tstamp skips socket that do not have
SOF_TIMESTAMPING_TX_ACK bit set in sk_tsflags. This is
implemented based on an implicit assumption that the
SOF_TIMESTAMPING_TX_ACK is set via socket options for the
duration that ACK timestamps are needed.
To implement per-write timestamps, this check should be
removed and replaced with a per-packet alternative that
quickly skips packets missing ACK timestamps marks without
a cache-line miss.
To enable per-packet marking without a cache line miss, use
one bit in TCP_SKB_CB to mark a whether a SKB might need a
ack tx timestamp or not. Further checks in tcp_ack_tstamp are not
modified and work as before.
Signed-off-by: Soheil Hassas Yeganeh <soheil@google.com>
Acked-by: Willem de Bruijn <willemb@google.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
SOF_TIMESTAMPING_OPT_ID is set to get data-independent IDs
to associate timestamps with send calls. For TCP connections,
tp->snd_una is used as the starting point to calculate
relative IDs.
This socket option will fail if set before the handshake on a
passive TCP fast open connection with data in SYN or SYN/ACK,
since setsockopt requires the connection to be in the
ESTABLISHED state.
To address these, instead of limiting the option to the
ESTABLISHED state, accept the SOF_TIMESTAMPING_OPT_ID option as
long as the connection is not in LISTEN or CLOSE states.
Signed-off-by: Soheil Hassas Yeganeh <soheil@google.com>
Acked-by: Willem de Bruijn <willemb@google.com>
Acked-by: Yuchung Cheng <ycheng@google.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
To process cmsg's of the SOL_SOCKET level in addition to
cmsgs of another level, protocols can call sock_cmsg_send().
This causes a double walk on the cmsghdr list, one for SOL_SOCKET
and one for the other level.
Extract the inner demultiplex logic from the loop that walks the list,
to allow having this called directly from a walker in the protocol
specific code.
Signed-off-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: Soheil Hassas Yeganeh <soheil@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Merge PAGE_CACHE_SIZE removal patches from Kirill Shutemov:
"PAGE_CACHE_{SIZE,SHIFT,MASK,ALIGN} macros were introduced *long* time
ago with promise that one day it will be possible to implement page
cache with bigger chunks than PAGE_SIZE.
This promise never materialized. And unlikely will.
Let's stop pretending that pages in page cache are special. They are
not.
The first patch with most changes has been done with coccinelle. The
second is manual fixups on top.
The third patch removes macros definition"
[ I was planning to apply this just before rc2, but then I spaced out,
so here it is right _after_ rc2 instead.
As Kirill suggested as a possibility, I could have decided to only
merge the first two patches, and leave the old interfaces for
compatibility, but I'd rather get it all done and any out-of-tree
modules and patches can trivially do the converstion while still also
working with older kernels, so there is little reason to try to
maintain the redundant legacy model. - Linus ]
* PAGE_CACHE_SIZE-removal:
mm: drop PAGE_CACHE_* and page_cache_{get,release} definition
mm, fs: remove remaining PAGE_CACHE_* and page_cache_{get,release} usage
mm, fs: get rid of PAGE_CACHE_* and page_cache_{get,release} macros
|
|
Mostly direct substitution with occasional adjustment or removing
outdated comments.
Signed-off-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Acked-by: Michal Hocko <mhocko@suse.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
PAGE_CACHE_{SIZE,SHIFT,MASK,ALIGN} macros were introduced *long* time
ago with promise that one day it will be possible to implement page
cache with bigger chunks than PAGE_SIZE.
This promise never materialized. And unlikely will.
We have many places where PAGE_CACHE_SIZE assumed to be equal to
PAGE_SIZE. And it's constant source of confusion on whether
PAGE_CACHE_* or PAGE_* constant should be used in a particular case,
especially on the border between fs and mm.
Global switching to PAGE_CACHE_SIZE != PAGE_SIZE would cause to much
breakage to be doable.
Let's stop pretending that pages in page cache are special. They are
not.
The changes are pretty straight-forward:
- <foo> << (PAGE_CACHE_SHIFT - PAGE_SHIFT) -> <foo>;
- <foo> >> (PAGE_CACHE_SHIFT - PAGE_SHIFT) -> <foo>;
- PAGE_CACHE_{SIZE,SHIFT,MASK,ALIGN} -> PAGE_{SIZE,SHIFT,MASK,ALIGN};
- page_cache_get() -> get_page();
- page_cache_release() -> put_page();
This patch contains automated changes generated with coccinelle using
script below. For some reason, coccinelle doesn't patch header files.
I've called spatch for them manually.
The only adjustment after coccinelle is revert of changes to
PAGE_CAHCE_ALIGN definition: we are going to drop it later.
There are few places in the code where coccinelle didn't reach. I'll
fix them manually in a separate patch. Comments and documentation also
will be addressed with the separate patch.
virtual patch
@@
expression E;
@@
- E << (PAGE_CACHE_SHIFT - PAGE_SHIFT)
+ E
@@
expression E;
@@
- E >> (PAGE_CACHE_SHIFT - PAGE_SHIFT)
+ E
@@
@@
- PAGE_CACHE_SHIFT
+ PAGE_SHIFT
@@
@@
- PAGE_CACHE_SIZE
+ PAGE_SIZE
@@
@@
- PAGE_CACHE_MASK
+ PAGE_MASK
@@
expression E;
@@
- PAGE_CACHE_ALIGN(E)
+ PAGE_ALIGN(E)
@@
expression E;
@@
- page_cache_get(E)
+ get_page(E)
@@
expression E;
@@
- page_cache_release(E)
+ put_page(E)
Signed-off-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Acked-by: Michal Hocko <mhocko@suse.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
The skcpiher/shash conversion introduced a number of bugs in the
sunrpc code:
1) Missing calls to skcipher_request_set_tfm lead to crashes.
2) The allocation size of shash_desc is too small which leads to
memory corruption.
Fixes: 3b5cf20cf439 ("sunrpc: Use skcipher and ahash/shash")
Reported-by: J. Bruce Fields <bfields@fieldses.org>
Tested-by: J. Bruce Fields <bfields@fieldses.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
Since nla_get_in_addr and nla_put_in_addr were implemented,
so use them appropriately.
Signed-off-by: Haishuang Yan <yanhaishuang@cmss.chinamobile.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
For non-SACK connections, cwnd is lowered to inflight plus 3 packets
when the recovery ends. This is an optional feature in the NewReno
RFC 2582 to reduce the potential burst when cwnd is "re-opened"
after recovery and inflight is low.
This feature is questionably effective because of PRR: when
the recovery ends (i.e., snd_una == high_seq) NewReno holds the
CA_Recovery state for another round trip to prevent false fast
retransmits. But if the inflight is low, PRR will overwrite the
moderated cwnd in tcp_cwnd_reduction() later regardlessly. So if a
receiver responds bogus ACKs (i.e., acking future data) to speed up
transfer after recovery, it can only induce a burst up to a window
worth of data packets by acking up to SND.NXT. A restart from (short)
idle or receiving streched ACKs can both cause such bursts as well.
On the other hand, if the recovery ends because the sender
detects the losses were spurious (e.g., reordering). This feature
unconditionally lowers a reverted cwnd even though nothing
was lost.
By principle loss recovery module should not update cwnd. Further
pacing is much more effective to reduce burst. Hence this patch
removes the cwnd moderation feature.
v2 changes: revised commit message on bogus ACKs and burst, and
missing signature
Signed-off-by: Matt Mathis <mattmathis@google.com>
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: Soheil Hassas Yeganeh <soheil@google.com>
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Pull networking fixes from David Miller:
1) Missing device reference in IPSEC input path results in crashes
during device unregistration. From Subash Abhinov Kasiviswanathan.
2) Per-queue ISR register writes not being done properly in macb
driver, from Cyrille Pitchen.
3) Stats accounting bugs in bcmgenet, from Patri Gynther.
4) Lightweight tunnel's TTL and TOS were swapped in netlink dumps, from
Quentin Armitage.
5) SXGBE driver has off-by-one in probe error paths, from Rasmus
Villemoes.
6) Fix race in save/swap/delete options in netfilter ipset, from
Vishwanath Pai.
7) Ageing time of bridge not set properly when not operating over a
switchdev device. Fix from Haishuang Yan.
8) Fix GRO regression wrt nested FOU/GUE based tunnels, from Alexander
Duyck.
9) IPV6 UDP code bumps wrong stats, from Eric Dumazet.
10) FEC driver should only access registers that actually exist on the
given chipset, fix from Fabio Estevam.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (73 commits)
net: mvneta: fix changing MTU when using per-cpu processing
stmmac: fix MDIO settings
Revert "stmmac: Fix 'eth0: No PHY found' regression"
stmmac: fix TX normal DESC
net: mvneta: use cache_line_size() to get cacheline size
net: mvpp2: use cache_line_size() to get cacheline size
net: mvpp2: fix maybe-uninitialized warning
tun, bpf: fix suspicious RCU usage in tun_{attach, detach}_filter
net: usb: cdc_ncm: adding Telit LE910 V2 mobile broadband card
rtnl: fix msg size calculation in if_nlmsg_size()
fec: Do not access unexisting register in Coldfire
net: mvneta: replace MVNETA_CPU_D_CACHE_LINE_SIZE with L1_CACHE_BYTES
net: mvpp2: replace MVPP2_CPU_D_CACHE_LINE_SIZE with L1_CACHE_BYTES
net: dsa: mv88e6xxx: Clear the PDOWN bit on setup
net: dsa: mv88e6xxx: Introduce _mv88e6xxx_phy_page_{read, write}
bpf: make padding in bpf_tunnel_key explicit
ipv6: udp: fix UDP_MIB_IGNOREDMULTI updates
bnxt_en: Fix ethtool -a reporting.
bnxt_en: Fix typo in bnxt_hwrm_set_pause_common().
bnxt_en: Implement proper firmware message padding.
...
|
|
Sasha Levin reported a suspicious rcu_dereference_protected() warning
found while fuzzing with trinity that is similar to this one:
[ 52.765684] net/core/filter.c:2262 suspicious rcu_dereference_protected() usage!
[ 52.765688] other info that might help us debug this:
[ 52.765695] rcu_scheduler_active = 1, debug_locks = 1
[ 52.765701] 1 lock held by a.out/1525:
[ 52.765704] #0: (rtnl_mutex){+.+.+.}, at: [<ffffffff816a64b7>] rtnl_lock+0x17/0x20
[ 52.765721] stack backtrace:
[ 52.765728] CPU: 1 PID: 1525 Comm: a.out Not tainted 4.5.0+ #264
[...]
[ 52.765768] Call Trace:
[ 52.765775] [<ffffffff813e488d>] dump_stack+0x85/0xc8
[ 52.765784] [<ffffffff810f2fa5>] lockdep_rcu_suspicious+0xd5/0x110
[ 52.765792] [<ffffffff816afdc2>] sk_detach_filter+0x82/0x90
[ 52.765801] [<ffffffffa0883425>] tun_detach_filter+0x35/0x90 [tun]
[ 52.765810] [<ffffffffa0884ed4>] __tun_chr_ioctl+0x354/0x1130 [tun]
[ 52.765818] [<ffffffff8136fed0>] ? selinux_file_ioctl+0x130/0x210
[ 52.765827] [<ffffffffa0885ce3>] tun_chr_ioctl+0x13/0x20 [tun]
[ 52.765834] [<ffffffff81260ea6>] do_vfs_ioctl+0x96/0x690
[ 52.765843] [<ffffffff81364af3>] ? security_file_ioctl+0x43/0x60
[ 52.765850] [<ffffffff81261519>] SyS_ioctl+0x79/0x90
[ 52.765858] [<ffffffff81003ba2>] do_syscall_64+0x62/0x140
[ 52.765866] [<ffffffff817d563f>] entry_SYSCALL64_slow_path+0x25/0x25
Same can be triggered with PROVE_RCU (+ PROVE_RCU_REPEATEDLY) enabled
from tun_attach_filter() when user space calls ioctl(tun_fd, TUN{ATTACH,
DETACH}FILTER, ...) for adding/removing a BPF filter on tap devices.
Since the fix in f91ff5b9ff52 ("net: sk_{detach|attach}_filter() rcu
fixes") sk_attach_filter()/sk_detach_filter() now dereferences the
filter with rcu_dereference_protected(), checking whether socket lock
is held in control path.
Since its introduction in 994051625981 ("tun: socket filter support"),
tap filters are managed under RTNL lock from __tun_chr_ioctl(). Thus the
sock_owned_by_user(sk) doesn't apply in this specific case and therefore
triggers the false positive.
Extend the BPF API with __sk_attach_filter()/__sk_detach_filter() pair
that is used by tap filters and pass in lockdep_rtnl_is_held() for the
rcu_dereference_protected() checks instead.
Reported-by: Sasha Levin <sasha.levin@oracle.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Size of the attribute IFLA_PHYS_PORT_NAME was missing.
Fixes: db24a9044ee1 ("net: add support for phys_port_name")
CC: David Ahern <dsahern@gmail.com>
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Acked-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We currently rely on the PMTU discovery of xfrm.
However if a packet is locally sent, the PMTU mechanism
of xfrm tries to do local socket notification what
might not work for applications like ping that don't
check for this. So add pmtu handling to vti_xmit to
report MTU changes immediately.
Reported-by: Mark McKinstry <Mark.McKinstry@alliedtelesis.co.nz>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
|
|
Make the 2 byte padding in struct bpf_tunnel_key between tunnel_ttl
and tunnel_label members explicit. No issue has been observed, and
gcc/llvm does padding for the old struct already, where tunnel_label
was not yet present, so the current code works, but since it's part
of uapi, make sure we don't introduce holes in structs.
Therefore, add tunnel_ext that we can use generically in future
(f.e. to flag OAM messages for backends, etc). Also add the offset
to the compat tests to be sure should some compilers not padd the
tail of the old version of bpf_tunnel_key.
Fixes: 4018ab1875e0 ("bpf: support flow label for bpf_skb_{set, get}_tunnel_key")
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
