| Age | Commit message (Collapse) | Author |
|---|
|
Currently a link is declared stale and reset if there has been 100
repeated attempts to retransmit the same packet. However, in certain
infrastructures we see that packet (NACK) duplicates and delays may
cause such retransmit attempts to occur at a high rate, so that the
peer doesn't have a reasonable chance to acknowledge the reception
before the 100-limit is hit. This may take much less than the
stipulated link tolerance time, and despite that probe/probe replies
otherwise go through as normal.
We now extend the criteria for link reset to also being time based.
I.e., we don't reset the link until the link tolerance time is passed
AND we have made 100 retransmissions attempts.
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
As support dissecting of QinQ inner and outer vlan headers, user can
add rules to match on QinQ vlan headers.
Signed-off-by: Jianbo Liu <jianbol@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently the encapsulated ethertype is not dumped as it's the same as
TCA_FLOWER_KEY_ETH_TYPE keyvalue. But the dumping result is inconsistent
with input, we add dumping it with TCA_FLOWER_KEY_VLAN_ETH_TYPE.
Signed-off-by: Jianbo Liu <jianbol@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Dissect the QinQ packets to get both outer and inner vlan information,
then store to the extended flow keys.
Signed-off-by: Jianbo Liu <jianbol@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
As flow dissector stores vlan ethertype, tc flower now can match on that.
It is to make preparation for supporting QinQ.
Signed-off-by: Jianbo Liu <jianbol@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Change vlan dissector key to save vlan tpid to support both 802.1Q
and 802.1AD ethertype.
Signed-off-by: Jianbo Liu <jianbol@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
smc_release() calls a sock_put() for smc fallback sockets to cover
the passive closing sock_hold() in __smc_connect() and
smc_tcp_listen_work(). This does not make sense for sockets in state
SMC_LISTEN and SMC_INIT.
An SMC socket stays in state SMC_INIT if connect fails. The sock_put
in smc_connect_abort() does not cover all failures. Move it into
smc_connect_decline_fallback().
Fixes: ee9dfbef02d18 ("net/smc: handle sockopts forcing fallback")
Reported-by: syzbot+3a0748c8f2f210c0ef9b@syzkaller.appspotmail.com
Reported-by: syzbot+9e60d2428a42049a592a@syzkaller.appspotmail.com
Signed-off-by: Ursula Braun <ubraun@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
rtnl_configure_link sets dev->rtnl_link_state to
RTNL_LINK_INITIALIZED and unconditionally calls
__dev_notify_flags to notify user-space of dev flags.
current call sequence for rtnl_configure_link
rtnetlink_newlink
rtnl_link_ops->newlink
rtnl_configure_link (unconditionally notifies userspace of
default and new dev flags)
If a newlink handler wants to call rtnl_configure_link
early, we will end up with duplicate notifications to
user-space.
This patch fixes rtnl_configure_link to check rtnl_link_state
and call __dev_notify_flags with gchanges = 0 if already
RTNL_LINK_INITIALIZED.
Later in the series, this patch will help the following sequence
where a driver implementing newlink can call rtnl_configure_link
to initialize the link early.
makes the following call sequence work:
rtnetlink_newlink
rtnl_link_ops->newlink (vxlan) -> rtnl_configure_link (initializes
link and notifies
user-space of default
dev flags)
rtnl_configure_link (updates dev flags if requested by user ifm
and notifies user-space of new dev flags)
Signed-off-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The setting of the node address is not thread safe, meaning that
two discoverers may decide to set it simultanously, with a duplicate
entry in the name table as result. We fix that with this commit.
Fixes: 25b0b9c4e835 ("tipc: handle collisions of 32-bit node address hash values")
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The duplicate address discovery protocol is not safe against two
discoverers running in parallel. The one executing first after the
trial period is over will set the node address and change its own
message type to DSC_REQ_MSG. The one executing last may find that the
node address is already set, and never change message type, with the
result that its links may never be established.
In this commmit we ensure that the message type always is set correctly
after the trial period is over.
Fixes: 25b0b9c4e835 ("tipc: handle collisions of 32-bit node address hash values")
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
With the duplicate address discovery protocol for tipc nodes addresses
we introduced a one second trial period before a node is allocated a
hash number to use as address.
Unfortunately, we miss to handle the case when a regular LINK REQUEST/
RESPONSE arrives from a cluster node during the trial period. Such
messages are not ignored as they should be, leading to links setup
attempts while the node still has no address.
Fixes: 25b0b9c4e835 ("tipc: handle collisions of 32-bit node address hash values")
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The function for checking if there is an node address conflict is
supposed to return a suggestion for a new address if it finds a
conflict, and zero otherwise. But in case the peer being checked
is previously unknown it does instead return a "suggestion" for
the checked address itself. This results in a DSC_TRIAL_FAIL_MSG
being sent unecessarily to the peer, and sometimes makes the trial
period starting over again.
Fixes: 25b0b9c4e835 ("tipc: handle collisions of 32-bit node address hash values")
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Now that ipc(6)->gso_size is correctly initialized in all callers of
ip(6)_setup_cork, it is safe to unconditionally pass it to the cork.
Link: http://lkml.kernel.org/r/20180619164752.143249-1-willemdebruijn.kernel@gmail.com
Signed-off-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
skb_shinfo(skb)->tx_flags is derived from sk->sk_tsflags, possibly
after modification by __sock_cmsg_send, by calling sock_tx_timestamp.
The IPv4 and IPv6 paths do this conversion differently. In IPv4, the
individual protocols that support tx timestamps call this function
and store the result in ipc.tx_flags. In IPv6, sock_tx_timestamp is
called in __ip6_append_data.
There is no need to store both tx_flags and ts_flags in the cookie
as one is derived from the other. Convert when setting up the cork
and remove the redundant field. This is similar to IPv6, only have
the conversion happen only once per datagram, in ip(6)_setup_cork.
Also change __ip6_append_data to match __ip_append_data. Only update
tskey if timestamping is enabled with OPT_ID. The SOCK_.. test is
redundant: only valid protocols can have non-zero cork->tx_flags.
After this change the IPv4 and IPv6 logic is the same.
Signed-off-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
ipcm_cookie includes sockcm_cookie. Do the same for ipcm6_cookie.
This reduces the number of arguments that need to be passed around,
applies ipcm6_init to all cookie fields at once and reduces code
differentiation between ipv4 and ipv6.
Signed-off-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Initialize the cookie in one location to reduce code duplication and
avoid bugs from inconsistent initialization, such as that fixed in
commit 9887cba19978 ("ip: limit use of gso_size to udp").
Signed-off-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Initialize the cookie in one location to reduce code duplication and
avoid bugs from inconsistent initialization, such as that fixed in
commit 9887cba19978 ("ip: limit use of gso_size to udp").
Signed-off-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Initialize the cookie in one location to reduce code duplication and
avoid bugs from inconsistent initialization, such as that fixed in
commit 9887cba19978 ("ip: limit use of gso_size to udp").
Signed-off-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This implements extended LE craete connection and enhanced
LE conn complete event if the controller supports.
For now it is as good as legacy LE connection and event as
no new features in the extended connection is handled.
< HCI Command: LE Extended Create Connection (0x08|0x0043) plen 26
Filter policy: White list is not used (0x00)
Own address type: Public (0x00)
Peer address type: Random (0x01)
Peer address: DB:7E:2E:1D:85:E8 (Static)
Initiating PHYs: 0x01
Entry 0: LE 1M
Scan interval: 60.000 msec (0x0060)
Scan window: 60.000 msec (0x0060)
Min connection interval: 50.00 msec (0x0028)
Max connection interval: 70.00 msec (0x0038)
Connection latency: 0 (0x0000)
Supervision timeout: 420 msec (0x002a)
Min connection length: 0.000 msec (0x0000)
Max connection length: 0.000 msec (0x0000)
> HCI Event: Command Status (0x0f) plen 4
LE Extended Create Connection (0x08|0x0043) ncmd 2
Status: Success (0x00)
> HCI Event: LE Meta Event (0x3e) plen 31
LE Enhanced Connection Complete (0x0a)
Status: Success (0x00)
Handle: 3585
Role: Master (0x00)
Peer address type: Random (0x01)
Peer address: DB:7E:2E:1D:85:E8 (Static)
Local resolvable private address: 00:00:00:00:00:00 (Non-Resolvable)
Peer resolvable private address: 00:00:00:00:00:00 (Non-Resolvable)
Connection interval: 67.50 msec (0x0036)
Connection latency: 0 (0x0000)
Supervision timeout: 420 msec (0x002a)
Master clock accuracy: 0x00
@ MGMT Event: Device Connected (0x000b) plen 40
LE Address: DB:7E:2E:1D:85:E8 (Static)
Flags: 0x00000000
Data length: 27
Name (complete): Designer Mouse
Appearance: Mouse (0x03c2)
Flags: 0x05
LE Limited Discoverable Mode
BR/EDR Not Supported
16-bit Service UUIDs (complete): 1 entry
Human Interface Device (0x1812)
Signed-off-by: Jaganath Kanakkassery <jaganathx.kanakkassery@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
This is done so that the helpers can be used for extended conn
implementation which will be done in subsequent patch.
Signed-off-by: Jaganath Kanakkassery <jaganathx.kanakkassery@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
This patch enables Extended ADV report event if extended scanning
is supported in the controller and process the same.
The new features are not handled and for now its as good as
legacy ADV report.
> HCI Event: LE Meta Event (0x3e) plen 53
LE Extended Advertising Report (0x0d)
Num reports: 1
Entry 0
Event type: 0x0013
Props: 0x0013
Connectable
Scannable
Use legacy advertising PDUs
Data status: Complete
Legacy PDU Type: ADV_IND (0x0013)
Address type: Random (0x01)
Address: DB:7E:2E:1A:85:E8 (Static)
Primary PHY: LE 1M
Secondary PHY: LE 1M
SID: 0x00
TX power: 0 dBm
RSSI: -90 dBm (0xa6)
Periodic advertising invteral: 0.00 msec (0x0000)
Direct address type: Public (0x00)
Direct address: 00:00:00:00:00:00 (OUI 00-00-00)
Data length: 0x1b
0f 09 44 65 73 69 67 6e 65 72 20 4d 6f 75 73 65 ..Designer Mouse
03 19 c2 03 02 01 05 03 03 12 18 ...........
Signed-off-by: Jaganath Kanakkassery <jaganathx.kanakkassery@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
This implements Set extended scan param and set extended scan enable
commands and use it for start LE scan based on controller support.
The new features added in these commands are setting of new PHY for
scanning and setting of scan duration. Both features are disabled
for now, meaning only 1M PHY is set and scan duration is set to 0
which means that scanning will be done untill scan disable is called.
< HCI Command: LE Set Extended Scan Parameters (0x08|0x0041) plen 8
Own address type: Random (0x01)
Filter policy: Accept all advertisement (0x00)
PHYs: 0x01
Entry 0: LE 1M
Type: Active (0x01)
Interval: 11.250 msec (0x0012)
Window: 11.250 msec (0x0012)
> HCI Event: Command Complete (0x0e) plen 4
LE Set Extended Scan Parameters (0x08|0x0041) ncmd 1
Status: Success (0x00)
< HCI Command: LE Set Extended Scan Enable (0x08|0x0042) plen 6
Extended scan: Enabled (0x01)
Filter duplicates: Enabled (0x01)
Duration: 0 msec (0x0000)
Period: 0.00 sec (0x0000)
> HCI Event: Command Complete (0x0e) plen 4
LE Set Extended Scan Enable (0x08|0x0042) ncmd 2
Status: Success (0x00)
Signed-off-by: Jaganath Kanakkassery <jaganathx.kanakkassery@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
Introduce a helper hci_req_start_scan() which starts an LE
scan and call it from passive_Scan() and active_scan().
There is not functionality change in this patch.
This is basically done to enable extended scanning if the
controller supports which will be done in the subsequent
patch
Signed-off-by: Jaganath Kanakkassery <jaganathx.kanakkassery@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
This patch disallows rbtree with single elements, which is causing
problems with the recent timeout support. Before this patch, you
could opt out individual set representations per module, which is
just adding extra complexity.
Fixes: 8d8540c4f5e0("netfilter: nft_set_rbtree: add timeout support")
Reported-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
The current implementation of cfg80211_rx_control_port assumed that the
caller could provide a contiguous region of memory for the control port
frame to be sent up to userspace. Unfortunately, many drivers produce
non-linear skbs, especially for data frames. This resulted in userspace
getting notified of control port frames with correct metadata (from
address, port, etc) yet garbage / nonsense contents, resulting in bad
handshakes, disconnections, etc.
mac80211 linearizes skbs containing management frames. But it didn't
seem worthwhile to do this for control port frames. Thus the signature
of cfg80211_rx_control_port was changed to take the skb directly.
nl80211 then takes care of obtaining control port frame data directly
from the (linear | non-linear) skb.
The caller is still responsible for freeing the skb,
cfg80211_rx_control_port does not take ownership of it.
Fixes: 6a671a50f819 ("nl80211: Add CMD_CONTROL_PORT_FRAME API")
Signed-off-by: Denis Kenzior <denkenz@gmail.com>
[fix some kernel-doc formatting, add fixes tag]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
This patch fixes a silent out-of-bound read possibility that was present
because of the misuse of this function.
Mostly it was called with a struct udphdr *hp which had only the udphdr
part linearized by the skb_header_pointer, however
nf_tproxy_get_sock_v{4,6} uses it as a tcphdr pointer, so some reads for
tcp specific attributes may be invalid.
Fixes: a583636a83ea ("inet: refactor inet[6]_lookup functions to take skb")
Signed-off-by: Máté Eckl <ecklm94@gmail.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
Check for Resolv list supported by controller. So check the supported
commmand first before issuing this command i.e.,HCI_OP_LE_CLEAR_RESOLV_LIST
Before patch:
< HCI Command: LE Read White List... (0x08|0x000f) plen 0 #55 [hci0] 13.338168
> HCI Event: Command Complete (0x0e) plen 5 #56 [hci0] 13.338842
LE Read White List Size (0x08|0x000f) ncmd 1
Status: Success (0x00)
Size: 25
< HCI Command: LE Clear White List (0x08|0x0010) plen 0 #57 [hci0] 13.339029
> HCI Event: Command Complete (0x0e) plen 4 #58 [hci0] 13.339939
LE Clear White List (0x08|0x0010) ncmd 1
Status: Success (0x00)
< HCI Command: LE Read Resolving L.. (0x08|0x002a) plen 0 #59 [hci0] 13.340152
> HCI Event: Command Complete (0x0e) plen 5 #60 [hci0] 13.340952
LE Read Resolving List Size (0x08|0x002a) ncmd 1
Status: Success (0x00)
Size: 25
< HCI Command: LE Read Maximum Dat.. (0x08|0x002f) plen 0 #61 [hci0] 13.341180
> HCI Event: Command Complete (0x0e) plen 12 #62 [hci0] 13.341898
LE Read Maximum Data Length (0x08|0x002f) ncmd 1
Status: Success (0x00)
Max TX octets: 251
Max TX time: 17040
Max RX octets: 251
Max RX time: 17040
After patch:
< HCI Command: LE Read White List... (0x08|0x000f) plen 0 #55 [hci0] 28.919131
> HCI Event: Command Complete (0x0e) plen 5 #56 [hci0] 28.920016
LE Read White List Size (0x08|0x000f) ncmd 1
Status: Success (0x00)
Size: 25
< HCI Command: LE Clear White List (0x08|0x0010) plen 0 #57 [hci0] 28.920164
> HCI Event: Command Complete (0x0e) plen 4 #58 [hci0] 28.920873
LE Clear White List (0x08|0x0010) ncmd 1
Status: Success (0x00)
< HCI Command: LE Read Resolving L.. (0x08|0x002a) plen 0 #59 [hci0] 28.921109
> HCI Event: Command Complete (0x0e) plen 5 #60 [hci0] 28.922016
LE Read Resolving List Size (0x08|0x002a) ncmd 1
Status: Success (0x00)
Size: 25
< HCI Command: LE Clear Resolving... (0x08|0x0029) plen 0 #61 [hci0] 28.922166
> HCI Event: Command Complete (0x0e) plen 4 #62 [hci0] 28.922872
LE Clear Resolving List (0x08|0x0029) ncmd 1
Status: Success (0x00)
< HCI Command: LE Read Maximum Dat.. (0x08|0x002f) plen 0 #63 [hci0] 28.923117
> HCI Event: Command Complete (0x0e) plen 12 #64 [hci0] 28.924030
LE Read Maximum Data Length (0x08|0x002f) ncmd 1
Status: Success (0x00)
Max TX octets: 251
Max TX time: 17040
Max RX octets: 251
Max RX time: 17040
Signed-off-by: Ankit Navik <ankit.p.navik@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
When the controller supports the Read LE Resolv List size feature, the
maximum list size are read and now stored.
Before patch:
< HCI Command: LE Read White List... (0x08|0x000f) plen 0 #55 [hci0] 17.979791
> HCI Event: Command Complete (0x0e) plen 5 #56 [hci0] 17.980629
LE Read White List Size (0x08|0x000f) ncmd 1
Status: Success (0x00)
Size: 25
< HCI Command: LE Clear White List (0x08|0x0010) plen 0 #57 [hci0] 17.980786
> HCI Event: Command Complete (0x0e) plen 4 #58 [hci0] 17.981627
LE Clear White List (0x08|0x0010) ncmd 1
Status: Success (0x00)
< HCI Command: LE Read Maximum Dat.. (0x08|0x002f) plen 0 #59 [hci0] 17.981786
> HCI Event: Command Complete (0x0e) plen 12 #60 [hci0] 17.982636
LE Read Maximum Data Length (0x08|0x002f) ncmd 1
Status: Success (0x00)
Max TX octets: 251
Max TX time: 17040
Max RX octets: 251
Max RX time: 17040
After patch:
< HCI Command: LE Read White List... (0x08|0x000f) plen 0 #55 [hci0] 13.338168
> HCI Event: Command Complete (0x0e) plen 5 #56 [hci0] 13.338842
LE Read White List Size (0x08|0x000f) ncmd 1
Status: Success (0x00)
Size: 25
< HCI Command: LE Clear White List (0x08|0x0010) plen 0 #57 [hci0] 13.339029
> HCI Event: Command Complete (0x0e) plen 4 #58 [hci0] 13.339939
LE Clear White List (0x08|0x0010) ncmd 1
Status: Success (0x00)
< HCI Command: LE Read Resolving L.. (0x08|0x002a) plen 0 #59 [hci0] 13.340152
> HCI Event: Command Complete (0x0e) plen 5 #60 [hci0] 13.340952
LE Read Resolving List Size (0x08|0x002a) ncmd 1
Status: Success (0x00)
Size: 25
< HCI Command: LE Read Maximum Dat.. (0x08|0x002f) plen 0 #61 [hci0] 13.341180
> HCI Event: Command Complete (0x0e) plen 12 #62 [hci0] 13.341898
LE Read Maximum Data Length (0x08|0x002f) ncmd 1
Status: Success (0x00)
Max TX octets: 251
Max TX time: 17040
Max RX octets: 251
Max RX time: 17040
Signed-off-by: Ankit Navik <ankit.p.navik@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
After decompression of 6lowpan socket data, an IPv6 header is inserted
before the existing socket payload. After this, we reset the
network_header value of the skb to account for the difference in payload
size from prior to decompression + the addition of the IPv6 header.
However, we fail to reset the mac_header value.
Leaving the mac_header value untouched here, can cause a calculation
error in net/packet/af_packet.c packet_rcv() function when an
AF_PACKET socket is opened in SOCK_RAW mode for use on a 6lowpan
interface.
On line 2088, the data pointer is moved backward by the value returned
from skb_mac_header(). If skb->data is adjusted so that it is before
the skb->head pointer (which can happen when an old value of mac_header
is left in place) the kernel generates a panic in net/core/skbuff.c
line 1717.
This panic can be generated by BLE 6lowpan interfaces (such as bt0) and
802.15.4 interfaces (such as lowpan0) as they both use the same 6lowpan
sources for compression and decompression.
Signed-off-by: Michael Scott <michael@opensourcefoundries.com>
Acked-by: Alexander Aring <aring@mojatatu.com>
Acked-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
The low and high values of the net.ipv4.ping_group_range sysctl were
being silently forced to the default disabled state when a write to the
sysctl contained GIDs that didn't map to the associated user namespace.
Confusingly, the sysctl's write operation would return success and then
a subsequent read of the sysctl would indicate that the low and high
values are the overflowgid.
This patch changes the behavior by clearly returning an error when the
sysctl write operation receives a GID range that doesn't map to the
associated user namespace. In such a situation, the previous value of
the sysctl is preserved and that range will be returned in a subsequent
read of the sysctl.
Signed-off-by: Tyler Hicks <tyhicks@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Essentially the same as the ipv4 equivalents.
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If we have an L3 master device, l3mdev_ip_rcv() will steal the skb, but
we were returning NET_RX_SUCCESS from ip_rcv_finish_core() which meant
that ip_list_rcv_finish() would keep it on the list. Instead let's
move the l3mdev_ip_rcv() call into the caller, so that our response to
a steal can be different in the single packet path (return
NET_RX_SUCCESS) and the list path (forget this packet and continue).
Fixes: 5fa12739a53d ("net: ipv4: listify ip_rcv_finish")
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
commit a2d4df9b673c ("spelling.txt: add more spellings to spelling.txt")
introduced the spellcheck of "cache" for checkpatch.pl.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
|
|
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
Warning level 2 was used: -Wimplicit-fallthrough=2
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
Warning level 2 was used: -Wimplicit-fallthrough=2
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
All the control messages broadcast to remote routers are using
QRTR_NODE_BCAST instead of using local router NODE ID which cause
the packets to be dropped on remote router due to invalid NODE ID.
Signed-off-by: Arun Kumar Neelakantam <aneela@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The broadcast node id should only be sent with the control port id.
Signed-off-by: Arun Kumar Neelakantam <aneela@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
At present the ipv6_renew_options_kern() function ends up calling into
access_ok() which is problematic if done from inside an interrupt as
access_ok() calls WARN_ON_IN_IRQ() on some (all?) architectures
(x86-64 is affected). Example warning/backtrace is shown below:
WARNING: CPU: 1 PID: 3144 at lib/usercopy.c:11 _copy_from_user+0x85/0x90
...
Call Trace:
<IRQ>
ipv6_renew_option+0xb2/0xf0
ipv6_renew_options+0x26a/0x340
ipv6_renew_options_kern+0x2c/0x40
calipso_req_setattr+0x72/0xe0
netlbl_req_setattr+0x126/0x1b0
selinux_netlbl_inet_conn_request+0x80/0x100
selinux_inet_conn_request+0x6d/0xb0
security_inet_conn_request+0x32/0x50
tcp_conn_request+0x35f/0xe00
? __lock_acquire+0x250/0x16c0
? selinux_socket_sock_rcv_skb+0x1ae/0x210
? tcp_rcv_state_process+0x289/0x106b
tcp_rcv_state_process+0x289/0x106b
? tcp_v6_do_rcv+0x1a7/0x3c0
tcp_v6_do_rcv+0x1a7/0x3c0
tcp_v6_rcv+0xc82/0xcf0
ip6_input_finish+0x10d/0x690
ip6_input+0x45/0x1e0
? ip6_rcv_finish+0x1d0/0x1d0
ipv6_rcv+0x32b/0x880
? ip6_make_skb+0x1e0/0x1e0
__netif_receive_skb_core+0x6f2/0xdf0
? process_backlog+0x85/0x250
? process_backlog+0x85/0x250
? process_backlog+0xec/0x250
process_backlog+0xec/0x250
net_rx_action+0x153/0x480
__do_softirq+0xd9/0x4f7
do_softirq_own_stack+0x2a/0x40
</IRQ>
...
While not present in the backtrace, ipv6_renew_option() ends up calling
access_ok() via the following chain:
access_ok()
_copy_from_user()
copy_from_user()
ipv6_renew_option()
The fix presented in this patch is to perform the userspace copy
earlier in the call chain such that it is only called when the option
data is actually coming from userspace; that place is
do_ipv6_setsockopt(). Not only does this solve the problem seen in
the backtrace above, it also allows us to simplify the code quite a
bit by removing ipv6_renew_options_kern() completely. We also take
this opportunity to cleanup ipv6_renew_options()/ipv6_renew_option()
a small amount as well.
This patch is heavily based on a rough patch by Al Viro. I've taken
his original patch, converted a kmemdup() call in do_ipv6_setsockopt()
to a memdup_user() call, made better use of the e_inval jump target in
the same function, and cleaned up the use ipv6_renew_option() by
ipv6_renew_options().
CC: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Paul Moore <paul@paul-moore.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
enable_sriov - Enables Single-Root Input/Output Virtualization(SR-IOV)
characteristic of the device.
Reviewed-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add 2 first generic parameters to devlink configuration parameters set:
internal_err_reset - When set enables reset device on internal errors.
max_macs - max number of MACs per ETH port.
Signed-off-by: Moshe Shemesh <moshe@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add devlink_param_notify() function to support devlink param notifications.
Add notification call to devlink param set, register and unregister
functions.
Add devlink_param_value_changed() function to enable the driver notify
devlink on value change. Driver should use this function after value was
changed on any configuration mode part to driverinit.
Signed-off-by: Moshe Shemesh <moshe@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
"driverinit" configuration mode value is held by devlink to enable
the driver query the value after reload. Two additional functions
added to help the driver get/set the value from/to devlink:
devlink_param_driverinit_value_set() and
devlink_param_driverinit_value_get().
Signed-off-by: Moshe Shemesh <moshe@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add param set command to set value for a parameter.
Value can be set to any of the supported configuration modes.
Signed-off-by: Moshe Shemesh <moshe@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add param get command which gets data per parameter.
Option to dump the parameters data per device.
Signed-off-by: Moshe Shemesh <moshe@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Define configuration parameters data structure.
Add functions to register and unregister the driver supported
configuration parameters table.
For each parameter registered, the driver should fill all the parameter's
fields. In case the only supported configuration mode is "driverinit"
the parameter's get()/set() functions are not required and should be set
to NULL, for any other configuration mode, these functions are required
and should be set by the driver.
Signed-off-by: Moshe Shemesh <moshe@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
After commit 07d78363dcff ("net: Convert NAPI gro list into a small hash
table.")' there is 8 hash buckets, which allows more flows to be held for
merging. but MAX_GRO_SKBS, the total held skb for merging, is 8 skb still,
limit the hash table performance.
keep MAX_GRO_SKBS as 8 skb, but limit each hash list length to 8 skb, not
the total 8 skb
Signed-off-by: Li RongQing <lirongqing@baidu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
nft_compat relies on xt_request_find_match to increment
refcount of the module that provides the match/target.
The (builtin) icmp matches did't set the module owner so it
was possible to rmmod ip(6)tables while icmp extensions were still in use.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
Otherwise NetworkManager (and iproute alike) is not able to identify the
parent IEEE 802.15.4 interface of a 6LoWPAN link.
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Acked-by: Alexander Aring <aring@mojatatu.com>
Signed-off-by: Stefan Schmidt <stefan@datenfreihafen.org>
|
|
Since callees (ip_rcv_core() and ip_rcv_finish_core()) might free or steal
the skb, we can't use the list_cut_before() method; we can't even do a
list_del(&skb->list) in the drop case, because skb might have already been
freed and reused.
So instead, take each skb off the source list before processing, and add it
to the sublist afterwards if it wasn't freed or stolen.
Fixes: 5fa12739a53d net: ipv4: listify ip_rcv_finish
Fixes: 17266ee93984 net: ipv4: listified version of ip_rcv
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
