| Age | Commit message (Collapse) | Author |
|---|
|
Any bridge options specified during link creation (e.g. ip link add)
are ignored as br_dev_newlink() does not process them.
Use br_changelink() to do it.
Fixes: 133235161721 ("bridge: implement rtnl_link_ops->changelink")
Signed-off-by: Ivan Vecera <cera@cera.cz>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Only the Marvell mv88e6xxx DSA driver made use of the HWMON support in
DSA. The temperature sensor registers are actually in the embedded
PHYs, and the PHY driver now supports it. So remove all HWMON support
from DSA and drivers.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When comparing two sockets we need to use inet6_rcv_saddr so we get a NULL
sk_v6_rcv_saddr if the socket isn't AF_INET6, otherwise our comparison function
can be wrong.
Fixes: 637bc8b ("inet: reset tb->fastreuseport when adding a reuseport sk")
Signed-off-by: Josef Bacik <jbacik@fb.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
netdev_rx_handler_register() checks to see if the handler is already
busy which was recently separated into netdev_is_rx_handler_busy(). So
use the same function inside register() to avoid code duplication.
Essentially this change should be a no-op
Signed-off-by: Mahesh Bandewar <maheshb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The fq_codel qdisc currently always regenerates the skb flow hash.
This wastes some cycles and prevents flow seperation in cases where
the traffic has been encrypted and can no longer be understood by the
flow dissector.
Change it to use the prexisting flow hash if one exists, and only
regenerate if necessary.
Signed-off-by: Andrew Collins <acollins@cradlepoint.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If the bearer carrying multicast messages supports broadcast, those
messages will be sent to all cluster nodes, irrespective of whether
these nodes host any actual destinations socket or not. This is clearly
wasteful if the cluster is large and there are only a few real
destinations for the message being sent.
In this commit we extend the eligibility of the newly introduced
"replicast" transmit option. We now make it possible for a user to
select which method he wants to be used, either as a mandatory setting
via setsockopt(), or as a relative setting where we let the broadcast
layer decide which method to use based on the ratio between cluster
size and the message's actual number of destination nodes.
In the latter case, a sending socket must stick to a previously
selected method until it enters an idle period of at least 5 seconds.
This eliminates the risk of message reordering caused by method change,
i.e., when changes to cluster size or number of destinations would
otherwise mandate a new method to be used.
Reviewed-by: Parthasarathy Bhuvaragan <parthasarathy.bhuvaragan@ericsson.com>
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
TIPC multicast messages are currently carried over a reliable
'broadcast link', making use of the underlying media's ability to
transport packets as L2 broadcast or IP multicast to all nodes in
the cluster.
When the used bearer is lacking that ability, we can instead emulate
the broadcast service by replicating and sending the packets over as
many unicast links as needed to reach all identified destinations.
We now introduce a new TIPC link-level 'replicast' service that does
this.
Reviewed-by: Parthasarathy Bhuvaragan <parthasarathy.bhuvaragan@ericsson.com>
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
As a further preparation for the upcoming 'replicast' functionality,
we add some necessary structs and functions for looking up and returning
a list of all nodes that host destinations for a given multicast message.
Reviewed-by: Parthasarathy Bhuvaragan <parthasarathy.bhuvaragan@ericsson.com>
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
As a preparation for the 'replicast' functionality we are going to
introduce in the next commits, we need the broadcast base structure to
store whether bearer broadcast is available at all from the currently
used bearer or bearers.
We do this by adding a new function tipc_bearer_bcast_support() to
the bearer layer, and letting the bearer selection function in
bcast.c use this to give a new boolean field, 'bcast_support' the
appropriate value.
Reviewed-by: Parthasarathy Bhuvaragan <parthasarathy.bhuvaragan@ericsson.com>
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Now that pci_bus_type has num_vf callback set, dev_num_vf can be
implemented in a bus type independent way and the check for whether a
PCI device is being handled in rtnetlink can be dropped.
Signed-off-by: Phil Sutter <phil@nwl.cc>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Commit b05229f44228 ("gre6: Cleanup GREv6 transmit path, call common GRE
functions") removed the ip6gre specific transmit function, but left the
struct ipv6_tel_txoption definition. Clean it up.
Signed-off-by: Jakub Sitnicki <jkbs@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This reverts commit 0e73fc9a56f22f2eec4d2b2910c649f7af67b74d.
This fix wasn't correct, a better one is coming right up.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Shaohua Li made percpu_counter irq safe in commit 098faf5805c8
("percpu_counter: make APIs irq safe")
We can safely remove BH disable/enable sections around various
percpu_counter manipulations.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The comparison on the timeout can lead to an array overrun
read on sctp_timer_tbl because of an off-by-one error. Fix
this by using < instead of <= and also compare to the array
size rather than SCTP_EVENT_TIMEOUT_MAX.
Fixes CoverityScan CID#1397639 ("Out-of-bounds read")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
seg6_genl_get_tunsrc() and set_tun_src() do not handle tun_src being
possibly NULL, so we must check kmemdup() return value and abort if
it is NULL
Fixes: 915d7e5e5930 ("ipv6: sr: add code base for control plane support of SR-IPv6")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: David Lebrun <david.lebrun@uclouvain.be>
Acked-by: David Lebrun <david.lebrun@uclouvain.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Commit 501db511397f ("virtio: don't set VIRTIO_NET_HDR_F_DATA_VALID on
xmit") in fact disables VIRTIO_HDR_F_DATA_VALID on receiving path too,
fixing this by adding a hint (has_data_valid) and set it only on the
receiving path.
Cc: Rolf Neugebauer <rolf.neugebauer@docker.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Acked-by: Rolf Neugebauer <rolf.neugebauer@docker.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
IPv6 deletes route entries associated with multipath routes on an
admin down where IPv4 does not. For example:
$ ip ro ls vrf red
unreachable default metric 8192
1.1.1.0/24 metric 64
nexthop via 10.100.1.254 dev eth1 weight 1
nexthop via 10.100.2.254 dev eth2 weight 1
10.100.1.0/24 dev eth1 proto kernel scope link src 10.100.1.4
10.100.2.0/24 dev eth2 proto kernel scope link src 10.100.2.4
$ ip -6 ro ls vrf red
2001:db8:1::/120 dev eth1 proto kernel metric 256 pref medium
2001:db8:2:: dev red proto none metric 0 pref medium
2001:db8:2::/120 dev eth2 proto kernel metric 256 pref medium
2001:db8:11::/120 via 2001:db8:1::16 dev eth1 metric 1024 pref medium
2001:db8:11::/120 via 2001:db8:2::17 dev eth2 metric 1024 pref medium
...
Set link down:
$ ip li set eth1 down
IPv4 retains the multihop route but flags eth1 route as dead:
$ ip ro ls vrf red
unreachable default metric 8192
1.1.1.0/24
nexthop via 10.100.1.16 dev eth1 weight 1 dead linkdown
nexthop via 10.100.2.16 dev eth2 weight 1
10.100.2.0/24 dev eth2 proto kernel scope link src 10.100.2.4
and IPv6 deletes the route as part of flushing all routes for the device:
$ ip -6 ro ls vrf red
2001:db8:2:: dev red proto none metric 0 pref medium
2001:db8:2::/120 dev eth2 proto kernel metric 256 pref medium
2001:db8:11::/120 via 2001:db8:2::17 dev eth2 metric 1024 pref medium
...
Worse, on admin up of the device the multipath route has to be deleted
to get this leg of the route re-added.
This patch keeps routes that are part of a multipath route if
ignore_routes_with_linkdown is set with the dead and linkdown flags
enabling consistency between IPv4 and IPv6:
$ ip -6 ro ls vrf red
2001:db8:2:: dev red proto none metric 0 pref medium
2001:db8:2::/120 dev eth2 proto kernel metric 256 pref medium
2001:db8:11::/120 via 2001:db8:1::16 dev eth1 metric 1024 dead linkdown pref medium
2001:db8:11::/120 via 2001:db8:2::17 dev eth2 metric 1024 pref medium
...
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The stats member of struct chnl_net is used nowhere in the code, so it
might as well be removed.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Found that if we run LTP netstress test with large MSS (65K),
the first attempt from server to send data comparable to this
MSS on fastopen connection will be delayed by the probe timer.
Here is an example:
< S seq 0:0 win 43690 options [mss 65495 wscale 7 tfo cookie] length 32
> S. seq 0:0 ack 1 win 43690 options [mss 65495 wscale 7] length 0
< . ack 1 win 342 length 0
Inside tcp_sendmsg(), tcp_send_mss() returns max MSS in 'mss_now',
as well as in 'size_goal'. This results the segment not queued for
transmition until all the data copied from user buffer. Then, inside
__tcp_push_pending_frames(), it breaks on send window test and
continues with the check probe timer.
Fragmentation occurs in tcp_write_wakeup()...
+0.2 > P. seq 1:43777 ack 1 win 342 length 43776
< . ack 43777, win 1365 length 0
> P. seq 43777:65001 ack 1 win 342 options [...] length 21224
...
This also contradicts with the fact that we should bound to the half
of the window if it is large.
Fix this flaw by correctly initializing max_window. Before that, it
could have large values that affect further calculations of 'size_goal'.
Fixes: 168a8f58059a ("tcp: TCP Fast Open Server - main code path")
Signed-off-by: Alexey Kodanev <alexey.kodanev@oracle.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The new ARP support has pushed the stack size over the edge on ARM,
as there are two large objects on the stack in this function (mask
and tb) and both have now grown a bit more:
net/sched/cls_flower.c: In function 'fl_change':
net/sched/cls_flower.c:928:1: error: the frame size of 1072 bytes is larger than 1024 bytes [-Werror=frame-larger-than=]
We can solve this by dynamically allocating one or both of them.
I first tried to do it just for the mask, but that only saved
152 bytes on ARM, while this version just does it for the 'tb'
array, bringing the stack size back down to 664 bytes.
Fixes: 99d31326cbe6 ("net/sched: cls_flower: Support matching on ARP")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Just like commit 4acd4945cd1e ("ipv6: addrconf: Avoid calling
netdevice notifiers with RCU read-side lock"), it is unnecessary
to make addrconf_disable_change() use RCU iteration over the
netdev list, since it already holds the RTNL lock, or we may meet
Illegal context switch in RCU read-side critical section.
Signed-off-by: Kefeng Wang <wangkefeng.wang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This further refines the changes made to conntrack gc_worker in
commit e0df8cae6c16 ("netfilter: conntrack: refine gc worker heuristics").
The main idea of that change was to reduce the scan interval when evictions
take place.
However, on the reporters' setup, there are 1-2 million conntrack entries
in total and roughly 8k new (and closing) connections per second.
In this case we'll always evict at least one entry per gc cycle and scan
interval is always at 1 jiffy because of this test:
} else if (expired_count) {
gc_work->next_gc_run /= 2U;
next_run = msecs_to_jiffies(1);
being true almost all the time.
Given we scan ~10k entries per run its clearly wrong to reduce interval
based on nonzero eviction count, it will only waste cpu cycles since a vast
majorities of conntracks are not timed out.
Thus only look at the ratio (scanned entries vs. evicted entries) to make
a decision on whether to reduce or not.
Because evictor is supposed to only kick in when system turns idle after
a busy period, pick a high ratio -- this makes it 50%. We thus keep
the idea of increasing scan rate when its likely that table contains many
expired entries.
In order to not let timed-out entries hang around for too long
(important when using event logging, in which case we want to timely
destroy events), we now scan the full table within at most
GC_MAX_SCAN_JIFFIES (16 seconds) even in worst-case scenario where all
timed-out entries sit in same slot.
I tested this with a vm under synflood (with
sysctl net.netfilter.nf_conntrack_tcp_timeout_syn_recv=3).
While flood is ongoing, interval now stays at its max rate
(GC_MAX_SCAN_JIFFIES / GC_MAX_BUCKETS_DIV -> 125ms).
With feedback from Nicolas Dichtel.
Reported-by: Denys Fedoryshchenko <nuclearcat@nuclearcat.com>
Cc: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Fixes: b87a2f9199ea82eaadc ("netfilter: conntrack: add gc worker to remove timed-out entries")
Signed-off-by: Florian Westphal <fw@strlen.de>
Tested-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Acked-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Tested-by: Denys Fedoryshchenko <nuclearcat@nuclearcat.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
Instead of breaking loop and instant resched, don't bother checking
this in first place (the loop calls cond_resched for every bucket anyway).
Suggested-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: Florian Westphal <fw@strlen.de>
Acked-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
The network stack no longer uses the last_rx member of struct net_device
since the bonding driver switched to use its own private last_rx in
commit 9f242738376d ("bonding: use last_arp_rx in slave_last_rx()").
However, some drivers still (ab)use the field for their own purposes and
some driver just update it without actually using it.
Previously, there was an accompanying comment for the last_rx member
added in commit 4dc89133f49b ("net: add a comment on netdev->last_rx")
which asked drivers not to update is, unless really needed. However,
this commend was removed in commit f8ff080dacec ("bonding: remove
useless updating of slave->dev->last_rx"), so some drivers added later
on still did update last_rx.
Remove all usage of last_rx and switch three drivers (sky2, atp and
smc91c92_cs) which actually read and write it to use their own private
copy in netdev_priv.
Compile-tested with allyesconfig and allmodconfig on x86 and arm.
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Jay Vosburgh <j.vosburgh@gmail.com>
Cc: Veaceslav Falico <vfalico@gmail.com>
Cc: Andy Gospodarek <andy@greyhouse.net>
Cc: Mirko Lindner <mlindner@marvell.com>
Cc: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Acked-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Jay Vosburgh <jay.vosburgh@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Trying to add an mpls encap route when the MPLS modules are not loaded
hangs. For example:
CONFIG_MPLS=y
CONFIG_NET_MPLS_GSO=m
CONFIG_MPLS_ROUTING=m
CONFIG_MPLS_IPTUNNEL=m
$ ip route add 10.10.10.10/32 encap mpls 100 via inet 10.100.1.2
The ip command hangs:
root 880 826 0 21:25 pts/0 00:00:00 ip route add 10.10.10.10/32 encap mpls 100 via inet 10.100.1.2
$ cat /proc/880/stack
[<ffffffff81065a9b>] call_usermodehelper_exec+0xd6/0x134
[<ffffffff81065efc>] __request_module+0x27b/0x30a
[<ffffffff814542f6>] lwtunnel_build_state+0xe4/0x178
[<ffffffff814aa1e4>] fib_create_info+0x47f/0xdd4
[<ffffffff814ae451>] fib_table_insert+0x90/0x41f
[<ffffffff814a8010>] inet_rtm_newroute+0x4b/0x52
...
modprobe is trying to load rtnl-lwt-MPLS:
root 881 5 0 21:25 ? 00:00:00 /sbin/modprobe -q -- rtnl-lwt-MPLS
and it hangs after loading mpls_router:
$ cat /proc/881/stack
[<ffffffff81441537>] rtnl_lock+0x12/0x14
[<ffffffff8142ca2a>] register_netdevice_notifier+0x16/0x179
[<ffffffffa0033025>] mpls_init+0x25/0x1000 [mpls_router]
[<ffffffff81000471>] do_one_initcall+0x8e/0x13f
[<ffffffff81119961>] do_init_module+0x5a/0x1e5
[<ffffffff810bd070>] load_module+0x13bd/0x17d6
...
The problem is that lwtunnel_build_state is called with rtnl lock
held preventing mpls_init from registering.
Given the potential references held by the time lwtunnel_build_state it
can not drop the rtnl lock to the load module. So, extract the module
loading code from lwtunnel_build_state into a new function to validate
the encap type. The new function is called while converting the user
request into a fib_config which is well before any table, device or
fib entries are examined.
Fixes: 745041e2aaf1 ("lwtunnel: autoload of lwt modules")
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Now that the DSA Ethernet switches are true Linux devices, the CPU
switch is not necessarily the first one. If its address is higher than
the second switch on the same MDIO bus, its index will be 1, not 0.
Avoid any confusion by using dst->cpu_switch instead of dst->ds[0].
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Store a dsa_switch pointer to the CPU switch in the tree instead of only
its index. This avoids the need to initialize it to -1.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The prefix arg to rt6_fill_node is non-0 in only 1 path - rt6_dump_route
where a user is requesting a prefix only dump. Simplify rt6_fill_node
by removing the prefix arg and moving the prefix check to rt6_dump_route.
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
All callers of rt6_fill_node pass 0 for nowait arg. Remove the arg and
simplify rt6_fill_node accordingly.
rt6_fill_node passes the nowait of 0 to ip6mr_get_route. Remove the
nowait arg from it as well.
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Ashizuka reported a highmem oddity and sent a patch for freescale
fec driver.
But the problem root cause is that core networking stack
must ensure no skb with highmem fragment is ever sent through
a device that does not assert NETIF_F_HIGHDMA in its features.
We need to call illegal_highdma() from harmonize_features()
regardless of CSUM checks.
Fixes: ec5f06156423 ("net: Kill link between CSUM and SG features.")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Pravin Shelar <pshelar@ovn.org>
Reported-by: "Ashizuka, Yuusuke" <ashiduka@jp.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The return value of nf_tables_table_lookup() is valid pointer or one
pointer error. There are two cases:
1) IS_ERR(table) is true, it would return the error or reset the
table as NULL, it is unnecessary to perform the latter check
"table != NULL".
2) IS_ERR(obj) is false, the table is one valid pointer. It is also
unnecessary to perform that check.
The nf_tables_newset() and nf_tables_newobj() have same logic codes.
In summary, we could move the block of condition check "table != NULL"
in the else block to eliminate the original condition checks.
Signed-off-by: Gao Feng <fgao@ikuai8.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
32-bit socketcalls were not being logged by audit on x86_64 systems.
Log them. This is basically a duplicate of the call from
net/socket.c:sys_socketcall(), but it addresses the impedance mismatch
between 32-bit userspace process and 64-bit kernel audit.
See: https://github.com/linux-audit/audit-kernel/issues/14
Signed-off-by: Richard Guy Briggs <rgb@redhat.com>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Paul Moore <paul@paul-moore.com>
|
|
We can't access c->pde if CONFIG_PROC_FS is disabled:
net/ipv4/netfilter/ipt_CLUSTERIP.c: In function 'clusterip_config_find_get':
net/ipv4/netfilter/ipt_CLUSTERIP.c:147:9: error: 'struct clusterip_config' has no member named 'pde'
This moves the check inside of another #ifdef.
Fixes: 6c5d5cfbe3c5 ("netfilter: ipt_CLUSTERIP: check duplicate config when initializing")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
Ethtool channels respond struct was uninitialized when querying device
channel boundaries settings. As a result, unreported fields by the driver
hold garbage. This may cause sending unsupported params to driver.
Fixes: 8bf368620486 ('ethtool: ensure channel counts are within bounds ...')
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
CC: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch is to implement sender-side procedures for the Outgoing
and Incoming SSN Reset Request Parameter described in rfc6525 section
5.1.2 and 5.1.3.
It is also add sockopt SCTP_RESET_STREAMS in rfc6525 section 6.3.2
for users.
Note that the new asoc member strreset_outstanding is to make sure
only one reconf request chunk on the fly as rfc6525 section 5.1.1
demands.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch is to add sockopt SCTP_ENABLE_STREAM_RESET to get/set
strreset_enable to indicate which reconf request type it supports,
which is described in rfc6525 section 6.3.1.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch is to add reconf_enable field in all of asoc ep and netns
to indicate if they support stream reset.
When initializing, asoc reconf_enable get the default value from ep
reconf_enable which is from netns netns reconf_enable by default.
It is also to add reconf_capable in asoc peer part to know if peer
supports reconf_enable, the value is set if ext params have reconf
chunk support when processing init chunk, just as rfc6525 section
5.1.1 demands.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch is to add a primitive based on sctp primitive frame for
sending stream reconf request. It works as the other primitives,
and create a SCTP_CMD_REPLY command to send the request chunk out.
sctp_primitive_RECONF would be the api to send a reconf request
chunk.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch is to add a per transport timer based on sctp timer frame
for stream reconf chunk retransmission. It would start after sending
a reconf request chunk, and stop after receiving the response chunk.
If the timer expires, besides retransmitting the reconf request chunk,
it would also do the same thing with data RTO timer. like to increase
the appropriate error counts, and perform threshold management, possibly
destroying the asoc if sctp retransmission thresholds are exceeded, just
as section 5.1.1 describes.
This patch is also to add asoc strreset_chunk, it is used to save the
reconf request chunk, so that it can be retransmitted, and to check if
the response is really for this request by comparing the information
inside with the response chunk as well.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch is to add asoc strreset_outseq and strreset_inseq for
saving the reconf request sequence, initialize them when create
assoc and process init, and also to define Incoming and Outgoing
SSN Reset Request Parameter described in rfc6525 section 4.1 and
4.2, As they can be in one same chunk as section rfc6525 3.1-3
describes, it makes them in one function.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
After adding the following nft rule, then ping 224.0.0.1:
# nft add rule netdev t c pkttype host counter
The warning complain message will be printed out again and again:
WARNING: CPU: 0 PID: 10182 at net/netfilter/nft_meta.c:163 \
nft_meta_get_eval+0x3fe/0x460 [nft_meta]
[...]
Call Trace:
<IRQ>
dump_stack+0x85/0xc2
__warn+0xcb/0xf0
warn_slowpath_null+0x1d/0x20
nft_meta_get_eval+0x3fe/0x460 [nft_meta]
nft_do_chain+0xff/0x5e0 [nf_tables]
So we should deal with PACKET_LOOPBACK in netdev family too. For ipv4,
convert it to PACKET_BROADCAST/MULTICAST according to the destination
address's type; For ipv6, convert it to PACKET_MULTICAST directly.
Signed-off-by: Liping Zhang <zlpnobody@gmail.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
Since there's no broadcast address in IPV6, so in ipv6 family, the
PACKET_LOOPBACK must be multicast packets, there's no need to check
it again.
Signed-off-by: Liping Zhang <zlpnobody@gmail.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
If we have non reuseport sockets on a tb we will set tb->fastreuseport to 0 and
never set it again. Which means that in the future if we end up adding a bunch
of reuseport sk's to that tb we'll have to do the expensive scan every time.
Instead add the ipv4/ipv6 saddr fields to the bind bucket, as well as the family
so we know what comparison to make, and the ipv6 only setting so we can make
sure to compare with new sockets appropriately. Once one sk has made it onto
the list we know that there are no potential bind conflicts on the owners list
that match that sk's rcv_addr. So copy the sk's information into our bind
bucket and set tb->fastruseport to FASTREUSESOCK_STRICT so we know we have to do
an extra check for subsequent reuseport sockets and skip the expensive bind
conflict check.
Signed-off-by: Josef Bacik <jbacik@fb.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
inet_csk_get_port does two different things, it either scans for an open port,
or it tries to see if the specified port is available for use. Since these two
operations have different rules and are basically independent lets split them
into two different functions to make them both more readable.
Signed-off-by: Josef Bacik <jbacik@fb.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This is just wasted time, we've already found a tb that doesn't have a bind
conflict, and we don't drop the head lock so scanning again isn't going to give
us a different answer. Instead move the tb->reuse setting logic outside of the
found_tb path and put it in the success: path. Then make it so that we don't
goto again if we find a bind conflict in the found_tb path as we won't reach
this anymore when we are scanning for an ephemeral port.
Signed-off-by: Josef Bacik <jbacik@fb.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In inet_csk_get_port we seem to be using smallest_port to figure out where the
best place to look for a SO_REUSEPORT sk that matches with an existing set of
SO_REUSEPORT's. However if we get to the logic
if (smallest_size != -1) {
port = smallest_port;
goto have_port;
}
we will do a useless search, because we would have already done the
inet_csk_bind_conflict for that port and it would have returned 1, otherwise we
would have gone to found_tb and succeeded. Since this logic makes us do yet
another trip through inet_csk_bind_conflict for a port we know won't work just
delete this code and save us the time.
Signed-off-by: Josef Bacik <jbacik@fb.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The only difference between inet6_csk_bind_conflict and inet_csk_bind_conflict
is how they check the rcv_saddr, so delete this call back and simply
change inet_csk_bind_conflict to call inet_rcv_saddr_equal.
Signed-off-by: Josef Bacik <jbacik@fb.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We pass these per-protocol equal functions around in various places, but
we can just have one function that checks the sk->sk_family and then do
the right comparison function. I've also changed the ipv4 version to
not cast to inet_sock since it is unneeded.
Signed-off-by: Josef Bacik <jbacik@fb.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
... otherwise the crypto stack will align it for us with a GFP_ATOMIC
allocation and a memcpy() -- see skcipher_walk_first().
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
|
|
Because home-rolling your own is _awesome_, stop doing it. Provide
kref_put_lock(), just like kref_put_mutex() but for a spinlock.
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
