| Age | Commit message (Collapse) | Author |
|---|
|
This patch moves the code handling SKBTX_WIFI_STATUS inside the TX path
into an extra function. This allows us to reuse it inside the 802.11 encap
offloading datapath.
Signed-off-by: John Crispin <john@phrozen.org>
Link: https://lore.kernel.org/r/20191029091304.7330-2-john@phrozen.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
In the first 5 minutes after boot (time of INITIAL_JIFFIES),
ieee80211_sta_last_active() returns zero if last_ack is zero. This
leads to "inactive time" showing jiffies_to_msecs(jiffies).
# iw wlan0 station get fc:ec:da:64:a6:dd
Station fc:ec:da:64:a6:dd (on wlan0)
inactive time: 4294894049 ms
.
.
connected time: 70 seconds
Fix by returning last_rx if last_ack == 0.
Signed-off-by: Ahmed Zaki <anzaki@gmail.com>
Link: https://lore.kernel.org/r/20191031121243.27694-1-anzaki@gmail.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
If ieee80211_txq_setup_flows() fails, we don't clean up LED
state properly, leading to crashes later on, fix that.
Fixes: dc8b274f0952 ("mac80211: Move up init of TXQs")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Acked-by: Toke Høiland-Jørgensen <toke@toke.dk>
Link: https://lore.kernel.org/r/20191105154110.1ccf7112ba5d.I0ba865792446d051867b33153be65ce6b063d98c@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Currently, we scan over all network namespaces at each received
discovery message in order to check if the sending peer might be
present in a host local namespaces.
This is unnecessary since we can assume that a peer will not change its
location during an established session.
We now improve the condition for this testing so that we don't perform
any redundant scans.
Fixes: f73b12812a3d ("tipc: improve throughput between nodes in netns")
Acked-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: Hoang Le <hoang.h.le@dektech.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
KCSAN reported a data-race [1]
While we can use READ_ONCE() on the read sides,
we need to make sure hh->hh_len is written last.
[1]
BUG: KCSAN: data-race in eth_header_cache / neigh_resolve_output
write to 0xffff8880b9dedcb8 of 4 bytes by task 29760 on cpu 0:
eth_header_cache+0xa9/0xd0 net/ethernet/eth.c:247
neigh_hh_init net/core/neighbour.c:1463 [inline]
neigh_resolve_output net/core/neighbour.c:1480 [inline]
neigh_resolve_output+0x415/0x470 net/core/neighbour.c:1470
neigh_output include/net/neighbour.h:511 [inline]
ip6_finish_output2+0x7a2/0xec0 net/ipv6/ip6_output.c:116
__ip6_finish_output net/ipv6/ip6_output.c:142 [inline]
__ip6_finish_output+0x2d7/0x330 net/ipv6/ip6_output.c:127
ip6_finish_output+0x41/0x160 net/ipv6/ip6_output.c:152
NF_HOOK_COND include/linux/netfilter.h:294 [inline]
ip6_output+0xf2/0x280 net/ipv6/ip6_output.c:175
dst_output include/net/dst.h:436 [inline]
NF_HOOK include/linux/netfilter.h:305 [inline]
ndisc_send_skb+0x459/0x5f0 net/ipv6/ndisc.c:505
ndisc_send_ns+0x207/0x430 net/ipv6/ndisc.c:647
rt6_probe_deferred+0x98/0xf0 net/ipv6/route.c:615
process_one_work+0x3d4/0x890 kernel/workqueue.c:2269
worker_thread+0xa0/0x800 kernel/workqueue.c:2415
kthread+0x1d4/0x200 drivers/block/aoe/aoecmd.c:1253
ret_from_fork+0x1f/0x30 arch/x86/entry/entry_64.S:352
read to 0xffff8880b9dedcb8 of 4 bytes by task 29572 on cpu 1:
neigh_resolve_output net/core/neighbour.c:1479 [inline]
neigh_resolve_output+0x113/0x470 net/core/neighbour.c:1470
neigh_output include/net/neighbour.h:511 [inline]
ip6_finish_output2+0x7a2/0xec0 net/ipv6/ip6_output.c:116
__ip6_finish_output net/ipv6/ip6_output.c:142 [inline]
__ip6_finish_output+0x2d7/0x330 net/ipv6/ip6_output.c:127
ip6_finish_output+0x41/0x160 net/ipv6/ip6_output.c:152
NF_HOOK_COND include/linux/netfilter.h:294 [inline]
ip6_output+0xf2/0x280 net/ipv6/ip6_output.c:175
dst_output include/net/dst.h:436 [inline]
NF_HOOK include/linux/netfilter.h:305 [inline]
ndisc_send_skb+0x459/0x5f0 net/ipv6/ndisc.c:505
ndisc_send_ns+0x207/0x430 net/ipv6/ndisc.c:647
rt6_probe_deferred+0x98/0xf0 net/ipv6/route.c:615
process_one_work+0x3d4/0x890 kernel/workqueue.c:2269
worker_thread+0xa0/0x800 kernel/workqueue.c:2415
kthread+0x1d4/0x200 drivers/block/aoe/aoecmd.c:1253
ret_from_fork+0x1f/0x30 arch/x86/entry/entry_64.S:352
Reported by Kernel Concurrency Sanitizer on:
CPU: 1 PID: 29572 Comm: kworker/1:4 Not tainted 5.4.0-rc6+ #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
Workqueue: events rt6_probe_deferred
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: syzbot <syzkaller@googlegroups.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add layer 3 generic packet exception traps that can report trapped
packets and documentation of the traps.
Unlike drop traps, these exception traps also need to inject the packet
to the kernel's receive path. For example, a packet that was trapped due
to unreachable neighbour need to be injected into the kernel so that it
will trigger an ARP request or a neighbour solicitation message.
Signed-off-by: Amit Cohen <amitc@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add packet traps that can report packets that were dropped during layer
3 forwarding.
Signed-off-by: Amit Cohen <amitc@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
tcp_make_synack() already uses tcp_clock_ns(), and can pass
the value to cookie_init_timestamp() to avoid another call
to ktime_get_ns() helper.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We need to explicitely forbid read/store tearing in inet_peer_gc()
and inet_putpeer().
The following syzbot report reminds us about inet_putpeer()
running without a lock held.
BUG: KCSAN: data-race in inet_putpeer / inet_putpeer
write to 0xffff888121fb2ed0 of 4 bytes by interrupt on cpu 0:
inet_putpeer+0x37/0xa0 net/ipv4/inetpeer.c:240
ip4_frag_free+0x3d/0x50 net/ipv4/ip_fragment.c:102
inet_frag_destroy_rcu+0x58/0x80 net/ipv4/inet_fragment.c:228
__rcu_reclaim kernel/rcu/rcu.h:222 [inline]
rcu_do_batch+0x256/0x5b0 kernel/rcu/tree.c:2157
rcu_core+0x369/0x4d0 kernel/rcu/tree.c:2377
rcu_core_si+0x12/0x20 kernel/rcu/tree.c:2386
__do_softirq+0x115/0x33f kernel/softirq.c:292
invoke_softirq kernel/softirq.c:373 [inline]
irq_exit+0xbb/0xe0 kernel/softirq.c:413
exiting_irq arch/x86/include/asm/apic.h:536 [inline]
smp_apic_timer_interrupt+0xe6/0x280 arch/x86/kernel/apic/apic.c:1137
apic_timer_interrupt+0xf/0x20 arch/x86/entry/entry_64.S:830
native_safe_halt+0xe/0x10 arch/x86/kernel/paravirt.c:71
arch_cpu_idle+0x1f/0x30 arch/x86/kernel/process.c:571
default_idle_call+0x1e/0x40 kernel/sched/idle.c:94
cpuidle_idle_call kernel/sched/idle.c:154 [inline]
do_idle+0x1af/0x280 kernel/sched/idle.c:263
write to 0xffff888121fb2ed0 of 4 bytes by interrupt on cpu 1:
inet_putpeer+0x37/0xa0 net/ipv4/inetpeer.c:240
ip4_frag_free+0x3d/0x50 net/ipv4/ip_fragment.c:102
inet_frag_destroy_rcu+0x58/0x80 net/ipv4/inet_fragment.c:228
__rcu_reclaim kernel/rcu/rcu.h:222 [inline]
rcu_do_batch+0x256/0x5b0 kernel/rcu/tree.c:2157
rcu_core+0x369/0x4d0 kernel/rcu/tree.c:2377
rcu_core_si+0x12/0x20 kernel/rcu/tree.c:2386
__do_softirq+0x115/0x33f kernel/softirq.c:292
run_ksoftirqd+0x46/0x60 kernel/softirq.c:603
smpboot_thread_fn+0x37d/0x4a0 kernel/smpboot.c:165
kthread+0x1d4/0x200 drivers/block/aoe/aoecmd.c:1253
ret_from_fork+0x1f/0x30 arch/x86/entry/entry_64.S:352
Reported by Kernel Concurrency Sanitizer on:
CPU: 1 PID: 16 Comm: ksoftirqd/1 Not tainted 5.4.0-rc3+ #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
Fixes: 4b9d9be839fd ("inetpeer: remove unused list")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: syzbot <syzkaller@googlegroups.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Hendrik reported routes in the main table using source address are not
removed when the address is removed. The problem is that fib_sync_down_addr
does not account for devices in the default VRF which are associated
with the main table. Fix by updating the table id reference.
Fixes: 5a56a0b3a45d ("net: Don't delete routes in different VRFs")
Reported-by: Hendrik Donner <hd@os-cillation.de>
Signed-off-by: David Ahern <dsahern@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
While looking at a syzbot KCSAN report [1], I found multiple
issues in this code :
1) fib6_nh->last_probe has an initial value of 0.
While probably okay on 64bit kernels, this causes an issue
on 32bit kernels since the time_after(jiffies, 0 + interval)
might be false ~24 days after boot (for HZ=1000)
2) The data-race found by KCSAN
I could use READ_ONCE() and WRITE_ONCE(), but we also can
take the opportunity of not piling-up too many rt6_probe_deferred()
works by using instead cmpxchg() so that only one cpu wins the race.
[1]
BUG: KCSAN: data-race in find_match / find_match
write to 0xffff8880bb7aabe8 of 8 bytes by interrupt on cpu 1:
rt6_probe net/ipv6/route.c:663 [inline]
find_match net/ipv6/route.c:757 [inline]
find_match+0x5bd/0x790 net/ipv6/route.c:733
__find_rr_leaf+0xe3/0x780 net/ipv6/route.c:831
find_rr_leaf net/ipv6/route.c:852 [inline]
rt6_select net/ipv6/route.c:896 [inline]
fib6_table_lookup+0x383/0x650 net/ipv6/route.c:2164
ip6_pol_route+0xee/0x5c0 net/ipv6/route.c:2200
ip6_pol_route_output+0x48/0x60 net/ipv6/route.c:2452
fib6_rule_lookup+0x3d6/0x470 net/ipv6/fib6_rules.c:117
ip6_route_output_flags_noref+0x16b/0x230 net/ipv6/route.c:2484
ip6_route_output_flags+0x50/0x1a0 net/ipv6/route.c:2497
ip6_dst_lookup_tail+0x25d/0xc30 net/ipv6/ip6_output.c:1049
ip6_dst_lookup_flow+0x68/0x120 net/ipv6/ip6_output.c:1150
inet6_csk_route_socket+0x2f7/0x420 net/ipv6/inet6_connection_sock.c:106
inet6_csk_xmit+0x91/0x1f0 net/ipv6/inet6_connection_sock.c:121
__tcp_transmit_skb+0xe81/0x1d60 net/ipv4/tcp_output.c:1169
tcp_transmit_skb net/ipv4/tcp_output.c:1185 [inline]
tcp_xmit_probe_skb+0x19b/0x1d0 net/ipv4/tcp_output.c:3735
read to 0xffff8880bb7aabe8 of 8 bytes by interrupt on cpu 0:
rt6_probe net/ipv6/route.c:657 [inline]
find_match net/ipv6/route.c:757 [inline]
find_match+0x521/0x790 net/ipv6/route.c:733
__find_rr_leaf+0xe3/0x780 net/ipv6/route.c:831
find_rr_leaf net/ipv6/route.c:852 [inline]
rt6_select net/ipv6/route.c:896 [inline]
fib6_table_lookup+0x383/0x650 net/ipv6/route.c:2164
ip6_pol_route+0xee/0x5c0 net/ipv6/route.c:2200
ip6_pol_route_output+0x48/0x60 net/ipv6/route.c:2452
fib6_rule_lookup+0x3d6/0x470 net/ipv6/fib6_rules.c:117
ip6_route_output_flags_noref+0x16b/0x230 net/ipv6/route.c:2484
ip6_route_output_flags+0x50/0x1a0 net/ipv6/route.c:2497
ip6_dst_lookup_tail+0x25d/0xc30 net/ipv6/ip6_output.c:1049
ip6_dst_lookup_flow+0x68/0x120 net/ipv6/ip6_output.c:1150
inet6_csk_route_socket+0x2f7/0x420 net/ipv6/inet6_connection_sock.c:106
inet6_csk_xmit+0x91/0x1f0 net/ipv6/inet6_connection_sock.c:121
__tcp_transmit_skb+0xe81/0x1d60 net/ipv4/tcp_output.c:1169
Reported by Kernel Concurrency Sanitizer on:
CPU: 0 PID: 18894 Comm: udevd Not tainted 5.4.0-rc3+ #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
Fixes: cc3a86c802f0 ("ipv6: Change rt6_probe to take a fib6_nh")
Fixes: f547fac624be ("ipv6: rate-limit probes for neighbourless routes")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: syzbot <syzkaller@googlegroups.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The function nfc_put_device(dev) is called twice to drop the reference
to dev when there is no associated local llcp. Remove one of them to fix
the bug.
Fixes: 52feb444a903 ("NFC: Extend netlink interface for LTO, RW, and MIUX parameters support")
Fixes: d9b8d8e19b07 ("NFC: llcp: Service Name Lookup netlink interface")
Signed-off-by: Pan Bian <bianpan2016@163.com>
Reviewed-by: Johan Hovold <johan@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We leak the page that we use to create skb page fragments
when destroying the xfrm_state. Fix this by dropping a
page reference if a page was assigned to the xfrm_state.
Fixes: cac2661c53f3 ("esp4: Avoid skb_cow_data whenever possible")
Reported-by: JD <jdtxs00@gmail.com>
Reported-by: Paul Wouters <paul@nohats.ca>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
|
|
I forgot to change last_packets field in struct net_rate_estimator.
Without this fix, rate estimators would misbehave after more
than 2^32 packets have been sent.
Another solution would be to be careful and only use the
32 least significant bits of packets counters, but we have
a hole in net_rate_estimator structure and this looks
easier to read/maintain.
Fixes: d0083d98f685 ("net_sched: extend packet counter to 64bit")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Reading tp->recvmsg_inq after socket lock is released
raises a KCSAN warning [1]
Replace has_tss & has_cmsg by cmsg_flags and make
sure to not read tp->recvmsg_inq a second time.
[1]
BUG: KCSAN: data-race in tcp_chrono_stop / tcp_recvmsg
write to 0xffff888126adef24 of 2 bytes by interrupt on cpu 0:
tcp_chrono_set net/ipv4/tcp_output.c:2309 [inline]
tcp_chrono_stop+0x14c/0x280 net/ipv4/tcp_output.c:2338
tcp_clean_rtx_queue net/ipv4/tcp_input.c:3165 [inline]
tcp_ack+0x274f/0x3170 net/ipv4/tcp_input.c:3688
tcp_rcv_established+0x37e/0xf50 net/ipv4/tcp_input.c:5696
tcp_v4_do_rcv+0x381/0x4e0 net/ipv4/tcp_ipv4.c:1561
tcp_v4_rcv+0x19dc/0x1bb0 net/ipv4/tcp_ipv4.c:1942
ip_protocol_deliver_rcu+0x4d/0x420 net/ipv4/ip_input.c:204
ip_local_deliver_finish+0x110/0x140 net/ipv4/ip_input.c:231
NF_HOOK include/linux/netfilter.h:305 [inline]
NF_HOOK include/linux/netfilter.h:299 [inline]
ip_local_deliver+0x133/0x210 net/ipv4/ip_input.c:252
dst_input include/net/dst.h:442 [inline]
ip_rcv_finish+0x121/0x160 net/ipv4/ip_input.c:413
NF_HOOK include/linux/netfilter.h:305 [inline]
NF_HOOK include/linux/netfilter.h:299 [inline]
ip_rcv+0x18f/0x1a0 net/ipv4/ip_input.c:523
__netif_receive_skb_one_core+0xa7/0xe0 net/core/dev.c:5010
__netif_receive_skb+0x37/0xf0 net/core/dev.c:5124
netif_receive_skb_internal+0x59/0x190 net/core/dev.c:5214
napi_skb_finish net/core/dev.c:5677 [inline]
napi_gro_receive+0x28f/0x330 net/core/dev.c:5710
read to 0xffff888126adef25 of 1 bytes by task 7275 on cpu 1:
tcp_recvmsg+0x77b/0x1a30 net/ipv4/tcp.c:2187
inet_recvmsg+0xbb/0x250 net/ipv4/af_inet.c:838
sock_recvmsg_nosec net/socket.c:871 [inline]
sock_recvmsg net/socket.c:889 [inline]
sock_recvmsg+0x92/0xb0 net/socket.c:885
sock_read_iter+0x15f/0x1e0 net/socket.c:967
call_read_iter include/linux/fs.h:1889 [inline]
new_sync_read+0x389/0x4f0 fs/read_write.c:414
__vfs_read+0xb1/0xc0 fs/read_write.c:427
vfs_read fs/read_write.c:461 [inline]
vfs_read+0x143/0x2c0 fs/read_write.c:446
ksys_read+0xd5/0x1b0 fs/read_write.c:587
__do_sys_read fs/read_write.c:597 [inline]
__se_sys_read fs/read_write.c:595 [inline]
__x64_sys_read+0x4c/0x60 fs/read_write.c:595
do_syscall_64+0xcc/0x370 arch/x86/entry/common.c:290
entry_SYSCALL_64_after_hwframe+0x44/0xa9
Reported by Kernel Concurrency Sanitizer on:
CPU: 1 PID: 7275 Comm: sshd Not tainted 5.4.0-rc3+ #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
Fixes: b75eba76d3d7 ("tcp: send in-queue bytes in cmsg upon read")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Soheil Hassas Yeganeh <soheil@google.com>
Reported-by: syzbot <syzkaller@googlegroups.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
sk->sk_backlog.tail might be read without holding the socket spinlock,
we need to add proper READ_ONCE()/WRITE_ONCE() to silence the warnings.
KCSAN reported :
BUG: KCSAN: data-race in tcp_add_backlog / tcp_recvmsg
write to 0xffff8881265109f8 of 8 bytes by interrupt on cpu 1:
__sk_add_backlog include/net/sock.h:907 [inline]
sk_add_backlog include/net/sock.h:938 [inline]
tcp_add_backlog+0x476/0xce0 net/ipv4/tcp_ipv4.c:1759
tcp_v4_rcv+0x1a70/0x1bd0 net/ipv4/tcp_ipv4.c:1947
ip_protocol_deliver_rcu+0x4d/0x420 net/ipv4/ip_input.c:204
ip_local_deliver_finish+0x110/0x140 net/ipv4/ip_input.c:231
NF_HOOK include/linux/netfilter.h:305 [inline]
NF_HOOK include/linux/netfilter.h:299 [inline]
ip_local_deliver+0x133/0x210 net/ipv4/ip_input.c:252
dst_input include/net/dst.h:442 [inline]
ip_rcv_finish+0x121/0x160 net/ipv4/ip_input.c:413
NF_HOOK include/linux/netfilter.h:305 [inline]
NF_HOOK include/linux/netfilter.h:299 [inline]
ip_rcv+0x18f/0x1a0 net/ipv4/ip_input.c:523
__netif_receive_skb_one_core+0xa7/0xe0 net/core/dev.c:4929
__netif_receive_skb+0x37/0xf0 net/core/dev.c:5043
netif_receive_skb_internal+0x59/0x190 net/core/dev.c:5133
napi_skb_finish net/core/dev.c:5596 [inline]
napi_gro_receive+0x28f/0x330 net/core/dev.c:5629
receive_buf+0x284/0x30b0 drivers/net/virtio_net.c:1061
virtnet_receive drivers/net/virtio_net.c:1323 [inline]
virtnet_poll+0x436/0x7d0 drivers/net/virtio_net.c:1428
napi_poll net/core/dev.c:6311 [inline]
net_rx_action+0x3ae/0xa90 net/core/dev.c:6379
__do_softirq+0x115/0x33f kernel/softirq.c:292
invoke_softirq kernel/softirq.c:373 [inline]
irq_exit+0xbb/0xe0 kernel/softirq.c:413
exiting_irq arch/x86/include/asm/apic.h:536 [inline]
do_IRQ+0xa6/0x180 arch/x86/kernel/irq.c:263
ret_from_intr+0x0/0x19
native_safe_halt+0xe/0x10 arch/x86/kernel/paravirt.c:71
arch_cpu_idle+0x1f/0x30 arch/x86/kernel/process.c:571
default_idle_call+0x1e/0x40 kernel/sched/idle.c:94
cpuidle_idle_call kernel/sched/idle.c:154 [inline]
do_idle+0x1af/0x280 kernel/sched/idle.c:263
cpu_startup_entry+0x1b/0x20 kernel/sched/idle.c:355
start_secondary+0x208/0x260 arch/x86/kernel/smpboot.c:264
secondary_startup_64+0xa4/0xb0 arch/x86/kernel/head_64.S:241
read to 0xffff8881265109f8 of 8 bytes by task 8057 on cpu 0:
tcp_recvmsg+0x46e/0x1b40 net/ipv4/tcp.c:2050
inet_recvmsg+0xbb/0x250 net/ipv4/af_inet.c:838
sock_recvmsg_nosec net/socket.c:871 [inline]
sock_recvmsg net/socket.c:889 [inline]
sock_recvmsg+0x92/0xb0 net/socket.c:885
sock_read_iter+0x15f/0x1e0 net/socket.c:967
call_read_iter include/linux/fs.h:1889 [inline]
new_sync_read+0x389/0x4f0 fs/read_write.c:414
__vfs_read+0xb1/0xc0 fs/read_write.c:427
vfs_read fs/read_write.c:461 [inline]
vfs_read+0x143/0x2c0 fs/read_write.c:446
ksys_read+0xd5/0x1b0 fs/read_write.c:587
__do_sys_read fs/read_write.c:597 [inline]
__se_sys_read fs/read_write.c:595 [inline]
__x64_sys_read+0x4c/0x60 fs/read_write.c:595
do_syscall_64+0xcc/0x370 arch/x86/entry/common.c:290
entry_SYSCALL_64_after_hwframe+0x44/0xa9
Reported by Kernel Concurrency Sanitizer on:
CPU: 0 PID: 8057 Comm: syz-fuzzer Not tainted 5.4.0-rc6+ #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The commit 69c51582ff786 ("dpif-netlink: don't allocate per
thread netlink sockets"), in Open vSwitch ovs-vswitchd, has
changed the number of allocated sockets to just one per port
by moving the socket array from a per handler structure to
a per datapath one. In the kernel datapath, a vport will have
only one socket in most case, if so select it directly in
fast-path.
Signed-off-by: Tonghao Zhang <xiangxia.m.yue@gmail.com>
Acked-by: Pravin B Shelar <pshelar@ovn.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Pablo Neira Ayuso says:
====================
Netfilter fixes for net
The following patchset contains Netfilter fixes for net:
1) Missing register size validation in bitwise and cmp offloads.
2) Fix error code in ip_set_sockfn_get() when copy_to_user() fails,
from Dan Carpenter.
3) Oneliner to copy MAC address in IPv6 hash:ip,mac sets, from
Stefano Brivio.
4) Missing policy validation in ipset with NL_VALIDATE_STRICT,
from Jozsef Kadlecsik.
5) Fix unaligned access to private data area of nf_tables instructions,
from Lukas Wunner.
6) Relax check for object updates, reported as a regression by
Eric Garver, patch from Fernando Fernandez Mancera.
7) Crash on ebtables dnat extension when used from the output path.
From Florian Westphal.
8) Fix bogus EOPNOTSUPP when updating basechain flags.
9) Fix bogus EBUSY when updating a basechain that is already offloaded.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When preparing tunnel packets for the link failover or synchronization,
as for the safe algorithm, we added a dummy packet on the pair link but
never sent it out. In the case of failover, the pair link will be reset
anyway. But for link synching, it will always result in retransmission
of the dummy packet after that.
We have also observed that such the retransmission at the early stage
when a new node comes in a large cluster will take some time and hard
to be done, leading to the repeated retransmit failures and the link is
reset.
Since in commit 4929a932be33 ("tipc: optimize link synching mechanism")
we have already built a dummy 'TUNNEL_PROTOCOL' message on the new link
for the synchronization, there's no need for the dummy on the pair one,
this commit will skip it when the new mechanism takes in place. In case
nothing exists in the pair link's transmq, the link synching will just
start and stop shortly on the peer side.
The patch is backward compatible.
Acked-by: Jon Maloy <jon.maloy@ericsson.com>
Tested-by: Hoang Le <hoang.h.le@dektech.com.au>
Signed-off-by: Tuong Lien <tuong.t.lien@dektech.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Based on the code framework built on the last patch, to
support setting and dumping for vxlan, we only need to
add ip_tun_parse_opts_erspan() for .build_state and
ip_tun_fill_encap_opts_erspan() for .fill_encap and
if (tun_flags & TUNNEL_ERSPAN_OPT) for .get_encap_size.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Based on the code framework built on the last patch, to
support setting and dumping for vxlan, we only need to
add ip_tun_parse_opts_vxlan() for .build_state and
ip_tun_fill_encap_opts_vxlan() for .fill_encap and
if (tun_flags & TUNNEL_VXLAN_OPT) for .get_encap_size.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
To add options setting and dumping, .build_state(), .fill_encap() and
.get_encap_size() in ip_tun_lwt_ops needs to be extended:
ip_tun_build_state():
ip_tun_parse_opts():
ip_tun_parse_opts_geneve()
ip_tun_fill_encap_info():
ip_tun_fill_encap_opts():
ip_tun_fill_encap_opts_geneve()
ip_tun_encap_nlsize()
ip_tun_opts_nlsize():
if (tun_flags & TUNNEL_GENEVE_OPT)
ip_tun_parse_opts(), ip_tun_fill_encap_opts() and ip_tun_opts_nlsize()
processes LWTUNNEL_IP_OPTS.
ip_tun_parse_opts_geneve(), ip_tun_fill_encap_opts_geneve() and
if (tun_flags & TUNNEL_GENEVE_OPT) processes LWTUNNEL_IP_OPTS_GENEVE.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When comparing two tun_info, dst_cache member should have been skipped,
as dst_cache is a per cpu pointer and they are always different values
even in two tun_info with the same keys.
So this patch is to skip dst_cache member and compare the key, mode and
options_len only. For the future opts setting support, also to compare
options.
Fixes: 2d79849903e0 ("lwtunnel: ip tunnel: fix multiple routes with different encap")
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Without options copied to the dst tun_info in iptunnel_metadata_reply()
called by arp_process for handling arp_request, the generated arp_reply
packet may be dropped or sent out with wrong options for some tunnels
like erspan and vxlan, and the traffic will break.
Fixes: 63d008a4e9ee ("ipv4: send arp replies to the correct tunnel")
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If a pnet table entry is to be added mentioning a valid ethernet
interface, but an invalid infiniband or ISM device, the dev_put()
operation for the ethernet interface is called twice, resulting
in a negative refcount for the ethernet interface, which disables
removal of such a network interface.
This patch removes one of the dev_put() calls.
Fixes: 890a2cb4a966 ("net/smc: rework pnet table")
Signed-off-by: Ursula Braun <ubraun@linux.ibm.com>
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
With huge cluster (e.g >200nodes), the amount of that flow:
gap -> retransmit packet -> acked will take time in case of STATE_MSG
dropped/delayed because a lot of traffic. This lead to 1.5 sec tolerance
value criteria made link easy failure around 2nd, 3rd of failed
retransmission attempts.
Instead of re-introduced criteria of 99 faled retransmissions to fix the
issue, we increase failure detection timer to ten times tolerance value.
Fixes: 77cf8edbc0e7 ("tipc: simplify stale link failure criteria")
Acked-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: Hoang Le <hoang.h.le@dektech.com.au>
Acked-by: Jon
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
There are two improvements when re-calculate cluster capabilities:
- When deleting a specific down node, need to re-calculate.
- In tipc_node_cleanup(), do not need to re-calculate if node
is still existing in cluster.
Acked-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: Hoang Le <hoang.h.le@dektech.com.au>
Acked-by: Jon
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
TLS TX needs to release and re-acquire the socket lock if send buffer
fills up.
TLS SW TX path currently depends on only allowing one thread to enter
the function by the abuse of sk_write_pending. If another writer is
already waiting for memory no new ones are allowed in.
This has two problems:
- writers don't wake other threads up when they leave the kernel;
meaning that this scheme works for single extra thread (second
application thread or delayed work) because memory becoming
available will send a wake up request, but as Mallesham and
Pooja report with larger number of threads it leads to threads
being put to sleep indefinitely;
- the delayed work does not get _scheduled_ but it may _run_ when
other writers are present leading to crashes as writers don't
expect state to change under their feet (same records get pushed
and freed multiple times); it's hard to reliably bail from the
work, however, because the mere presence of a writer does not
guarantee that the writer will push pending records before exiting.
Ensuring wakeups always happen will make the code basically open
code a mutex. Just use a mutex.
The TLS HW TX path does not have any locking (not even the
sk_write_pending hack), yet it uses a per-socket sg_tx_data
array to push records.
Fixes: a42055e8d2c3 ("net/tls: Add support for async encryption of records for performance")
Reported-by: Mallesham Jatharakonda <mallesh537@gmail.com>
Reported-by: Pooja Trivedi <poojatrivedi@gmail.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
sk_write_pending being not zero does not guarantee that partial
record will be pushed. If the thread waiting for memory times out
the pending record may get stuck.
In case of tls_device there is no path where parial record is
set and writer present in the first place. Partial record is
set only in tls_push_sg() and tls_push_sg() will return an
error immediately. All tls_device callers of tls_push_sg()
will return (and not wait for memory) if it failed.
Fixes: a42055e8d2c3 ("net/tls: Add support for async encryption of records for performance")
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
sk->sk_max_ack_backlog can be read without any lock being held
at least in TCP/DCCP cases.
We need to use READ_ONCE()/WRITE_ONCE() to avoid load/store tearing
and/or potential KCSAN warnings.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
sk->sk_ack_backlog can be read without any lock being held.
We need to use READ_ONCE()/WRITE_ONCE() to avoid load/store tearing
and/or potential KCSAN warnings.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Writers are holding a lock, but many readers do not.
Following patch will add appropriate barriers in
sk_acceptq_removed() and sk_acceptq_added().
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Use jiffies_delta_to_msecs() to avoid reporting 'infinite'
timeouts and to cleanup code.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
A difference of two unsigned long needs long storage.
Fixes: c7fb64db001f ("[NETLINK]: Neighbour table configuration and statistics via rtnetlink")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.open-mesh.org/linux-merge
Simon Wunderlich says:
====================
This feature/cleanup patchset includes the following patches:
- bump version strings, by Simon Wunderlich
- Simplify batadv_v_ogm_aggr_list_free using skb_queue_purge,
by Christophe Jaillet
- Replace aggr_list_lock with lock free skb handlers,
by Christophe Jaillet
- explicitly mark fallthrough cases, by Sven Eckelmann
- Drop lockdep.h include from soft-interface.c, by Sven Eckelmann
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Now the kernel uses 64bit packet counters in scheduler layer,
we want to export these counters to user space.
Instead risking breaking user space by adding fields
to struct gnet_stats_basic, add a new TCA_STATS_PKT64.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
After this change, qdisc packet counter is no longer
a 32bit quantity. We still export 32bit values to user.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add wrappers around the devlink resource API, so that DSA drivers can
register and unregister devlink resources.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
sk_msg_trim() tries to only update curr pointer if it falls into
the trimmed region. The logic, however, does not take into the
account pointer wrapping that sk_msg_iter_var_prev() does nor
(as John points out) the fact that msg->sg is a ring buffer.
This means that when the message was trimmed completely, the new
curr pointer would have the value of MAX_MSG_FRAGS - 1, which is
neither smaller than any other value, nor would it actually be
correct.
Special case the trimming to 0 length a little bit and rework
the comparison between curr and end to take into account wrapping.
This bug caused the TLS code to not copy all of the message, if
zero copy filled in fewer sg entries than memcopy would need.
Big thanks to Alexander Potapenko for the non-KMSAN reproducer.
v2:
- take into account that msg->sg is a ring buffer (John).
Link: https://lore.kernel.org/netdev/20191030160542.30295-1-jakub.kicinski@netronome.com/ (v1)
Fixes: d829e9c4112b ("tls: convert to generic sk_msg interface")
Reported-by: syzbot+f8495bff23a879a6d0bd@syzkaller.appspotmail.com
Reported-by: syzbot+6f50c99e8f6194bf363f@syzkaller.appspotmail.com
Co-developed-by: John Fastabend <john.fastabend@gmail.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: John Fastabend <john.fastabend@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The openvswitch was supporting a MPLS label depth of 1 in the ingress
direction though the userspace OVS supports a max depth of 3 labels.
This change enables openvswitch module to support a max depth of
3 labels in the ingress.
Signed-off-by: Martin Varghese <martin.varghese@nokia.com>
Acked-by: Pravin B Shelar <pshelar@ovn.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Use 'skb_queue_purge()' instead of re-implementing it.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Reviewed-by: Stefano Garzarella <sgarzare@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The order in which the ports are deleted from the list and freed and the
call to dsa_switch_remove() is done is reversed, which leads to an
use after free condition. Reverse the two: first tear down the ports and
switch from the fabric, then free the ports associated with that switch
fabric.
Fixes: 05f294a85235 ("net: dsa: allocate ports on touch")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When a new filter is added to cls_api, the function
tcf_chain_tp_insert_unique() looks up the protocol/priority/chain to
determine if the tcf_proto is duplicated in the chain's hashtable. It then
creates a new entry or continues with an existing one. In cls_flower, this
allows the function fl_ht_insert_unque to determine if a filter is a
duplicate and reject appropriately, meaning that the duplicate will not be
passed to drivers via the offload hooks. However, when a tcf_proto is
destroyed it is removed from its chain before a hardware remove hook is
hit. This can lead to a race whereby the driver has not received the
remove message but duplicate flows can be accepted. This, in turn, can
lead to the offload driver receiving incorrect duplicate flows and out of
order add/delete messages.
Prevent duplicates by utilising an approach suggested by Vlad Buslov. A
hash table per block stores each unique chain/protocol/prio being
destroyed. This entry is only removed when the full destroy (and hardware
offload) has completed. If a new flow is being added with the same
identiers as a tc_proto being detroyed, then the add request is replayed
until the destroy is complete.
Fixes: 8b64678e0af8 ("net: sched: refactor tp insert/delete for concurrent execution")
Signed-off-by: John Hurley <john.hurley@netronome.com>
Signed-off-by: Vlad Buslov <vladbu@mellanox.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Reported-by: Louis Peens <louis.peens@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The same code which recognizes ICMP error packets is duplicated several
times. Use the icmp_is_err() and icmpv6_is_err() helpers instead, which
do the same thing.
ip_multipath_l3_keys() and tcf_nat_act() didn't check for all the error types,
assume that they should instead.
Signed-off-by: Matteo Croce <mcroce@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Don't swap oper and admin schedules too early, it's not correct and
causes crash.
Steps to reproduce:
1)
tc qdisc replace dev eth0 parent root handle 100 taprio \
num_tc 3 \
map 2 2 1 0 2 2 2 2 2 2 2 2 2 2 2 2 \
queues 1@0 1@1 1@2 \
base-time $SOME_BASE_TIME \
sched-entry S 01 80000 \
sched-entry S 02 15000 \
sched-entry S 04 40000 \
flags 2
2)
tc qdisc replace dev eth0 parent root handle 100 taprio \
base-time $SOME_BASE_TIME \
sched-entry S 01 90000 \
sched-entry S 02 20000 \
sched-entry S 04 40000 \
flags 2
3)
tc qdisc replace dev eth0 parent root handle 100 taprio \
base-time $SOME_BASE_TIME \
sched-entry S 01 150000 \
sched-entry S 02 200000 \
sched-entry S 04 40000 \
flags 2
Do 2 3 2 .. steps more times if not happens and observe:
[ 305.832319] Unable to handle kernel write to read-only memory at
virtual address ffff0000087ce7f0
[ 305.910887] CPU: 0 PID: 0 Comm: swapper/0 Not tainted
[ 305.919306] Hardware name: Texas Instruments AM654 Base Board (DT)
[...]
[ 306.017119] x1 : ffff800848031d88 x0 : ffff800848031d80
[ 306.022422] Call trace:
[ 306.024866] taprio_free_sched_cb+0x4c/0x98
[ 306.029040] rcu_process_callbacks+0x25c/0x410
[ 306.033476] __do_softirq+0x10c/0x208
[ 306.037132] irq_exit+0xb8/0xc8
[ 306.040267] __handle_domain_irq+0x64/0xb8
[ 306.044352] gic_handle_irq+0x7c/0x178
[ 306.048092] el1_irq+0xb0/0x128
[ 306.051227] arch_cpu_idle+0x10/0x18
[ 306.054795] do_idle+0x120/0x138
[ 306.058015] cpu_startup_entry+0x20/0x28
[ 306.061931] rest_init+0xcc/0xd8
[ 306.065154] start_kernel+0x3bc/0x3e4
[ 306.068810] Code: f2fbd5b7 f2fbd5b6 d503201f f9400422 (f9000662)
[ 306.074900] ---[ end trace 96c8e2284a9d9d6e ]---
[ 306.079507] Kernel panic - not syncing: Fatal exception in interrupt
[ 306.085847] SMP: stopping secondary CPUs
[ 306.089765] Kernel Offset: disabled
Try to explain one of the possible crash cases:
The "real" admin list is assigned when admin_sched is set to
new_admin, it happens after "swap", that assigns to oper_sched NULL.
Thus if call qdisc show it can crash.
Farther, next second time, when sched list is updated, the admin_sched
is not NULL and becomes the oper_sched, previous oper_sched was NULL so
just skipped. But then admin_sched is assigned new_admin, but schedules
to free previous assigned admin_sched (that already became oper_sched).
Farther, next third time, when sched list is updated,
while one more swap, oper_sched is not null, but it was happy to be
freed already (while prev. admin update), so while try to free
oper_sched the kernel panic happens at taprio_free_sched_cb().
So, move the "swap emulation" where it should be according to function
comment from code.
Fixes: 9c66d15646760e ("taprio: Add support for hardware offloading")
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Acked-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
Tested-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
total message size
We were sending malformed EOMA with total message size set to 0. This
issue has been fixed in the previous patch.
In this patch a sanity check is added to the RX path and a error message
is displayed.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
with the total message size set
We were sending malformed EOMA messageswith total message size set to 0.
This patch fixes the bug.
Reported-by: https://github.com/linux-can/can-utils/issues/159
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Acked-by: Kurt Van Dijck <dev.kurt@vandijck-laurijssen.be>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
Filters array is coped from user space and linked to the j1939 socket.
On socket release this memory was not freed.
Fixes: 9d71dd0c7009 ("can: add support of SAE J1939 protocol")
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
Currently the error return paths do not free skb and this results in a
memory leak. Fix this by freeing them before the return.
Addresses-Coverity: ("Resource leak")
Fixes: 9d71dd0c7009 ("can: add support of SAE J1939 protocol")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
Jozsef Kadlecsik says:
====================
ipset patches for nf
- Fix the error code in ip_set_sockfn_get() when copy_to_user() is used,
from Dan Carpenter.
- The IPv6 part was missed when fixing copying the right MAC address
in the patch "netfilter: ipset: Copy the right MAC address in bitmap:ip,mac
and hash:ip,mac sets", it is completed now by Stefano Brivio.
- ipset nla_policies are fixed to fully support NL_VALIDATE_STRICT and
the code is converted from deprecated parsings to verified ones.
====================
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
