| Age | Commit message (Collapse) | Author |
|---|
|
Now we can set/get Transmission Window size via sockopt.
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Reviewed-by: João Paulo Rechi Vita <jprvita@profusion.mobi>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
As specified by Bluetooth 3.0 spec we shall send an acknowledgment using
the Send-Ack() after clear the SREJ list.
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Reviewed-by: João Paulo Rechi Vita <jprvita@profusion.mobi>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
If the SDU size is greater than the MTU something is wrong, so report
an error.
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
[jprvita@profusion.mobi: set err to appropriate errno value]
Signed-off-by: João Paulo Rechi Vita <jprvita@profusion.mobi>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
Fix a possible problem with Big Endian machines.
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Reviewed-by: João Paulo Rechi Vita <jprvita@profusion.mobi>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
We were accepting values bigger than we can accept. This was leading
ERTM to drop packets because of wrong FCS checks.
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Reviewed-by: João Paulo Rechi Vita <jprvita@profusion.mobi>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
On Enhanced Retransmission Mode and Streaming Mode a entity can send, on
a successful Conf RSP, new values for the RFC fields. For example, the
entity can send txWindow and MPS values less than the value received on
a Conf REQ.
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Reviewed-by: João Paulo Rechi Vita <jprvita@profusion.mobi>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
Tx Window value shall not be used with Streaming Mode and the receiver
of the config Request shall ignore its value.
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Reviewed-by: João Paulo Rechi Vita <jprvita@profusion.mobi>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
We ack I-frames on each txWindow/5 I-frames received, but if the sender
stop to send I-frames and it's not a txWindow multiple we can leave some
frames unacked.
So I added a timer to ack I-frames on this case. The timer expires in
200ms.
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Reviewed-by: João Paulo Rechi Vita <jprvita@profusion.mobi>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
Now the code handles the case under SREJ_SENT state.
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Reviewed-by: João Paulo Rechi Vita <jprvita@profusion.mobi>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
tx_seq var already has the value of __get_reqseq().
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Reviewed-by: João Paulo Rechi Vita <jprvita@profusion.mobi>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
It also fix a bug: we weren't acknowledging I-frames when P=1.
Note that when F=1 we are acknowledging packets before setting
RemoteBusy to False. The spec says we should do that in the opposite
order, but acknowledment of packets doesn't care about RemoteBusy flag
so we can do that in the order we want.
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Reviewed-by: João Paulo Rechi Vita <jprvita@profusion.mobi>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
We weren't handling the receipt under SREJ_SENT state table.
It also introduce l2cap_send_srejtail(). It will be used in the nexts
commits too.
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Reviewed-by: João Paulo Rechi Vita <jprvita@profusion.mobi>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
Create a function for each type fo S-frame and avoid a lot of nested
code.
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Reviewed-by: João Paulo Rechi Vita <jprvita@profusion.mobi>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
This finishes the implementation of Recv RR (P=0)(F=0) for the Enhanced
Retransmission Mode on L2CAP.
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Reviewed-by: João Paulo Rechi Vita <jprvita@profusion.mobi>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
Abstract the send of of P-bit and avoids code duplication like we
did with the setting of F-bit.
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Reviewed-by: João Paulo Rechi Vita <jprvita@profusion.mobi>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
Shall be used to ack received frames, It must decide type of
acknowledgment between a RR frame, a RNR frame or transmission of
pending I-frames.
It also modifies l2cap_ertm_send() to report the number of frames sent.
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Reviewed-by: João Paulo Rechi Vita <jprvita@profusion.mobi>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
After reassembly the SDU we need to check his size. It can't overflow
the MTU size.
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Reviewed-by: João Paulo Rechi Vita <jprvita@profusion.mobi>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
All packets with size fewer than the minimum specified is dropped.
Note that the size of the l2cap basic header, FCS and SAR fields are
already subtracted of len at the moment of the size check.
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Reviewed-by: João Paulo Rechi Vita <jprvita@profusion.mobi>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
On receipt of a F=1 under WAIT_F state ERTM shall stop monitor timer and
start retransmission timer (if there are unacked frames).
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Reviewed-by: João Paulo Rechi Vita <jprvita@profusion.mobi>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
After receive a RR with P bit set ERTM shall use this funcion to choose
what type of frame to reply with F bit = 1.
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Reviewed-by: João Paulo Rechi Vita <jprvita@profusion.mobi>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
Trivial clean up.
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Reviewed-by: João Paulo Rechi Vita <jprvita@profusion.mobi>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
ERTM and Streaming Modes was having problems when the ACL MTU is lower
than MPS. The 'minus 10' is to take in account the header and fcs
lenghts.
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Reviewed-by: João Paulo Rechi Vita <jprvita@profusion.mobi>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
All operation related to the txWindow should be modulo 64.
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Reviewed-by: João Paulo Rechi Vita <jprvita@profusion.mobi>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
l2cap_data_channel do not free the S-frame, so we free it here.
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Reviewed-by: João Paulo Rechi Vita <jprvita@profusion.mobi>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
Inside "case L2CAP_MODE_BASIC:" we don't need to check for sk_type and
L2CAP mode. So only the length check is fine.
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Reviewed-by: João Paulo Rechi Vita <jprvita@profusion.mobi>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
Remove extra braces and labels, break over column 80 lines, etc
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
It also removes an unneeded check for the MTU. The check is done before
on sco_send_frame()
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Reviewed-by: João Paulo Rechi Vita <jprvita@profusion.mobi>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
A while back there was a discussion regarding the rt_secret_interval timer.
Given that we've had the ability to do emergency route cache rebuilds for awhile
now, based on a statistical analysis of the various hash chain lengths in the
cache, the use of the flush timer is somewhat redundant. This patch removes the
rt_secret_interval sysctl, allowing us to rely solely on the statistical
analysis mechanism to determine the need for route cache flushes.
Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Also simplify the flags assignment into a single statement at the
end of ieee80211_beacon_get_tim.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Currently, when one interface switches HT mode,
all others will follow along. This is clearly
undesirable, since the new one might switch to
no-HT while another one is operating in HT.
Address this issue by keeping track of the HT
mode per interface, and allowing only changes
that are compatible, i.e. switching into HT40+
is not possible when another interface is in
HT40-, in that case the second one needs to
fall back to HT20.
Also, to allow drivers to know what's going on,
store the per-interface HT mode (channel type)
in the virtual interface's bss_conf.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Currently (all tested with hwsim) you can do stupid
things like setting up an AP on a certain channel,
then adding another virtual interface and making
that associate on another channel -- this will make
the beaconing to move channel but obviously without
the necessary IEs data update.
In order to improve this situation, first make the
configuration APIs (cfg80211 and nl80211) aware of
multi-channel operation -- we'll eventually need
that in the future anyway. There's one userland API
change and one API addition. The API change is that
now SET_WIPHY must be called with virtual interface
index rather than only wiphy index in order to take
effect for that interface -- luckily all current
users (hostapd) do that. For monitor interfaces, the
old setting is preserved, but monitors are always
slaved to other devices anyway so no guarantees.
The second userland API change is the introduction
of a per virtual interface SET_CHANNEL command, that
hostapd should use going forward to make it easier
to understand what's going on (it can automatically
detect a kernel with this command).
Other than mac80211, no existing cfg80211 drivers
are affected by this change because they only allow
a single virtual interface.
mac80211, however, now needs to be aware that the
channel settings are per interface now, and needs
to disallow (for now) real multi-channel operation,
which is another important part of this patch.
One of the immediate benefits is that you can now
start hostapd to operate on a hardware that already
has a connection on another virtual interface, as
long as you specify the same channel.
Note that two things are left unhandled (this is an
improvement -- not a complete fix):
* different HT/no-HT modes
currently you could start an HT AP and then
connect to a non-HT network on the same channel
which would configure the hardware for no HT;
that can be fixed fairly easily
* CSA
An AP we're connected to on a virtual interface
might indicate switching channels, and in that
case we would follow it, regardless of how many
other interfaces are operating; this requires
more effort to fix but is pretty rare after all
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
When reconfiguring an interface due to a previous
hardware restart, mac80211 will currently include
the new IBSS flag on non-IBSS interfaces which may
confuse drivers.
Instead of doing the ~0 trick, simply spell out
which things are going to be reconfigured.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
In https://bugzilla.kernel.org/show_bug.cgi?id=15794 a user encountered the
following:
[18967.469098] wlan0: authenticated
[18967.472527] wlan0: associate with 00:1c:10:b8:e3:ea (try 1)
[18967.472585] wlan0: deauthenticating from 00:1c:10:b8:e3:ea by local choice (reason=3)
[18967.672057] wlan0: associate with 00:1c:10:b8:e3:ea (try 2)
[18967.872357] wlan0: associate with 00:1c:10:b8:e3:ea (try 3)
[18968.072960] wlan0: association with 00:1c:10:b8:e3:ea timed out
[18968.076890] ------------[ cut here ]------------
[18968.076898] WARNING: at net/wireless/mlme.c:341 cfg80211_send_assoc_timeout+0xa8/0x140()
[18968.076900] Hardware name: GX628
[18968.076924] Pid: 1408, comm: phy0 Not tainted 2.6.34-rc4-00082-g250541f-dirty #3
[18968.076926] Call Trace:
[18968.076931] [<ffffffff8103459e>] ? warn_slowpath_common+0x6e/0xb0
[18968.076934] [<ffffffff8157c2d8>] ? cfg80211_send_assoc_timeout+0xa8/0x140
[18968.076937] [<ffffffff8103ff8b>] ? mod_timer+0x10b/0x180
[18968.076940] [<ffffffff8158f0fc>] ? ieee80211_assoc_done+0xbc/0xc0
[18968.076943] [<ffffffff81590d53>] ? ieee80211_work_work+0x553/0x11c0
[18968.076945] [<ffffffff8102d931>] ? finish_task_switch+0x41/0xb0
[18968.076948] [<ffffffff81590800>] ? ieee80211_work_work+0x0/0x11c0
[18968.076951] [<ffffffff810476fb>] ? worker_thread+0x13b/0x210
[18968.076954] [<ffffffff8104b6b0>] ? autoremove_wake_function+0x0/0x30
[18968.076956] [<ffffffff810475c0>] ? worker_thread+0x0/0x210
[18968.076959] [<ffffffff8104b21e>] ? kthread+0x8e/0xa0
[18968.076962] [<ffffffff810031f4>] ? kernel_thread_helper+0x4/0x10
[18968.076964] [<ffffffff8104b190>] ? kthread+0x0/0xa0
[18968.076966] [<ffffffff810031f0>] ? kernel_thread_helper+0x0/0x10
[18968.076968] ---[ end trace 8aa6265f4b1adfe0 ]---
As explained by Johannes Berg <johannes@sipsolutions.net>:
We authenticate successfully, and then userspace requests association.
Then we start that process, but the AP doesn't respond. While we're
still waiting for an AP response, userspace asks for a deauth. We do
the deauth, but don't abort the association work. Then once the
association work times out we tell cfg80211, but it no longer wants
to know since for all it is concerned we accepted the deauth that
also kills the association attempt.
Fix this by, upon receipt of deauth request, removing the association work
and continuing to send the deauth.
Unfortunately the user reporting the issue is not able to reproduce this
problem anymore and cannot verify this fix. This seems like a well understood
issue though and I thus present the patch.
Bug-identified-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Introduce ____napi_schedule() helper for callers in irq disabled
contexts. rps_trigger_softirq() becomes a leaf function.
Use container_of() in process_backlog() instead of accessing per_cpu
address.
Use a custom inlined version of __napi_complete() in process_backlog()
to avoid one locked instruction :
only current cpu owns and manipulates this napi,
and NAPI_STATE_SCHED is the only possible flag set on backlog.
we can use a plain write instead of clear_bit(),
and we dont need an smp_mb() memory barrier, since RPS is on,
backlog is protected by a spinlock.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Adding addresses and ports to the short packet log message,
like ipv4/udp.c does it, makes these messages a lot more useful:
[ 822.182450] UDPv6: short packet: From [2001:db8:ffb4:3::1]:47839 23715/178 to [2001:db8:ffb4:3:5054:ff:feff:200]:1234
This requires us to drop logging in case pskb_may_pull() fails,
which also is consistent with ipv4/udp.c
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
commit 2783ef23 moved the initialisation of saddr and daddr after
pskb_may_pull() to avoid a potential data corruption. Unfortunately
also placing it after the short packet and bad checksum error paths,
where these variables are used for logging. The result is bogus
output like
[92238.389505] UDP: short packet: From 2.0.0.0:65535 23715/178 to 0.0.0.0:65535
Moving the saddr and daddr initialisation above the error paths, while still
keeping it after the pskb_may_pull() to keep the fix from commit 2783ef23.
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Cc: stable@kernel.org
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
ICMP protocol unreachable handling completely disregarded
the fact that the user may have locked the socket. It proceeded
to destroy the association, even though the user may have
held the lock and had a ref on the association. This resulted
in the following:
Attempt to release alive inet socket f6afcc00
=========================
[ BUG: held lock freed! ]
-------------------------
somenu/2672 is freeing memory f6afcc00-f6afcfff, with a lock still held
there!
(sk_lock-AF_INET){+.+.+.}, at: [<c122098a>] sctp_connect+0x13/0x4c
1 lock held by somenu/2672:
#0: (sk_lock-AF_INET){+.+.+.}, at: [<c122098a>] sctp_connect+0x13/0x4c
stack backtrace:
Pid: 2672, comm: somenu Not tainted 2.6.32-telco #55
Call Trace:
[<c1232266>] ? printk+0xf/0x11
[<c1038553>] debug_check_no_locks_freed+0xce/0xff
[<c10620b4>] kmem_cache_free+0x21/0x66
[<c1185f25>] __sk_free+0x9d/0xab
[<c1185f9c>] sk_free+0x1c/0x1e
[<c1216e38>] sctp_association_put+0x32/0x89
[<c1220865>] __sctp_connect+0x36d/0x3f4
[<c122098a>] ? sctp_connect+0x13/0x4c
[<c102d073>] ? autoremove_wake_function+0x0/0x33
[<c12209a8>] sctp_connect+0x31/0x4c
[<c11d1e80>] inet_dgram_connect+0x4b/0x55
[<c11834fa>] sys_connect+0x54/0x71
[<c103a3a2>] ? lock_release_non_nested+0x88/0x239
[<c1054026>] ? might_fault+0x42/0x7c
[<c1054026>] ? might_fault+0x42/0x7c
[<c11847ab>] sys_socketcall+0x6d/0x178
[<c10da994>] ? trace_hardirqs_on_thunk+0xc/0x10
[<c1002959>] syscall_call+0x7/0xb
This was because the sctp_wait_for_connect() would aqcure the socket
lock and then proceed to release the last reference count on the
association, thus cause the fully destruction path to finish freeing
the socket.
The simplest solution is to start a very short timer in case the socket
is owned by user. When the timer expires, we can do some verification
and be able to do the release properly.
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In case of congestion, netif_rx() frees the skb, so we must assume
dev_forward_skb() also consume skb.
Bug introduced by commit 445409602c092
(veth: move loopback logic to common location)
We must change dev_forward_skb() to always consume skb, and veth to not
double free it.
Bug report : http://marc.info/?l=linux-netdev&m=127310770900442&w=3
Reported-by: Martín Ferrari <martin.ferrari@gmail.com>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Based on the previous patch, make bridge support netpoll by:
1) implement the 2 methods to support netpoll for bridge;
2) modify netpoll during forwarding packets via bridge;
3) disable netpoll support of bridge when a netpoll-unabled device
is added to bridge;
4) enable netpoll support when all underlying devices support netpoll.
Cc: David Miller <davem@davemloft.net>
Cc: Neil Horman <nhorman@tuxdriver.com>
Cc: Stephen Hemminger <shemminger@linux-foundation.org>
Cc: Matt Mackall <mpm@selenic.com>
Signed-off-by: WANG Cong <amwang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This whole patchset is for adding netpoll support to bridge and bonding
devices. I already tested it for bridge, bonding, bridge over bonding,
and bonding over bridge. It looks fine now.
To make bridge and bonding support netpoll, we need to adjust
some netpoll generic code. This patch does the following things:
1) introduce two new priv_flags for struct net_device:
IFF_IN_NETPOLL which identifies we are processing a netpoll;
IFF_DISABLE_NETPOLL is used to disable netpoll support for a device
at run-time;
2) introduce one new method for netdev_ops:
->ndo_netpoll_cleanup() is used to clean up netpoll when a device is
removed.
3) introduce netpoll_poll_dev() which takes a struct net_device * parameter;
export netpoll_send_skb() and netpoll_poll_dev() which will be used later;
4) hide a pointer to struct netpoll in struct netpoll_info, ditto.
5) introduce ->real_dev for struct netpoll.
6) introduce a new status NETDEV_BONDING_DESLAE, which is used to disable
netconsole before releasing a slave, to avoid deadlocks.
Cc: David Miller <davem@davemloft.net>
Cc: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: WANG Cong <amwang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
I noticed when I added support for IPV6_DONTFRAG that if you set
IPV6_RECVERR and tried to send a UDP packet larger than 64K to an
IPv6 destination, you'd correctly get an EMSGSIZE, but reading from
MSG_ERRQUEUE returned the incorrect address in the cmsg:
struct msghdr:
msg_name 0x7fff8f3c96d0
msg_namelen 28
struct sockaddr_in6:
sin6_family 10
sin6_port 7639
sin6_flowinfo 0
sin6_addr ::ffff:38.32.0.0
sin6_scope_id 0 ((null))
It should have returned this in my case:
struct msghdr:
msg_name 0x7fffd866b510
msg_namelen 28
struct sockaddr_in6:
sin6_family 10
sin6_port 7639
sin6_flowinfo 0
sin6_addr 2620:0:a09:e000:21f:29ff:fe57:f88b
sin6_scope_id 0 ((null))
The problem is that ipv6_recv_error() assumes that if the error
wasn't generated by ICMPv6, it's an IPv4 address sitting there,
and proceeds to create a v4-mapped address from it.
Change ipv6_icmp_error() and ipv6_local_error() to set skb->protocol
to htons(ETH_P_IPV6) so that ipv6_recv_error() knows the address
sitting right after the extended error is IPv6, else it will
incorrectly map the first octet into an IPv4-mapped IPv6 address
in the cmsg structure returned in a recvmsg() call to obtain
the error.
Signed-off-by: Brian Haley <brian.haley@hp.com>
--
To unsubscribe from this list: send the line "unsubscribe netdev" in
the body of a message to majordomo@vger.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless-next-2.6
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless-next-2.6 into for-davem
Conflicts:
drivers/net/wireless/libertas_tf/cmd.c
drivers/net/wireless/libertas_tf/main.c
|
|
"mac80211: improve IBSS scanning" was missing a hunk.
This adds that hunk as originally intended.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6:
FEC: Fix kernel panic in fec_set_mac_address.
ipv6: Fix default multicast hops setting.
net: ep93xx_eth stops receiving packets
drivers/net/phy: micrel phy driver
dm9601: fix phy/eeprom write routine
ppp_generic: handle non-linear skbs when passing them to pppd
ppp_generic: pull 2 bytes so that PPP_PROTO(skb) is valid
net: fix compile error due to double return type in SOCK_DEBUG
net/usb: initiate sync sequence in sierra_net.c driver
net/usb: remove default in Kconfig for sierra_net driver
r8169: Fix rtl8169_rx_interrupt()
e1000e: Fix oops caused by ASPM patch.
net/sb1250: register mdio bus in probe
sctp: Fix skb_over_panic resulting from multiple invalid parameter errors (CVE-2010-1173) (v4)
p54pci: fix bugs in p54p_check_tx_ring
|
|
With following patch I can reach maximum rate of my pktgen+udpsink
simulator :
- 'old' machine : dual quad core E5450 @3.00GHz
- 64 UDP rx flows (only differ by destination port)
- RPS enabled, NIC interrupts serviced on cpu0
- rps dispatched on 7 other cores. (~130.000 IPI per second)
- SLAB allocator (faster than SLUB in this workload)
- tg3 NIC
- 1.080.000 pps without a single drop at NIC level.
Idea is to add two prefetchw() calls in __alloc_skb(), one to prefetch
first sk_buff cache line, the second to prefetch the shinfo part.
Also using one memset() to initialize all skb_shared_info fields instead
of one by one to reduce number of instructions, using long word moves.
All skb_shared_info fields before 'dataref' are cleared in
__alloc_skb().
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Conflicts:
fs/nfsd/nfs4callback.c
|
|
As per RFC 3493 the default multicast hops setting
for a socket should be "1" just like ipv4.
Ironically we have a IPV6_DEFAULT_MCASTHOPS macro
it just wasn't being used.
Reported-by: Elliot Hughes <enh@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Commit 4b0b72f7dd617b ( net: speedup udp receive path )
introduced a bug in skb_free_datagram_locked().
We should not skb_orphan() skb if we dont have the guarantee we are the
last skb user, this might happen with MSG_PEEK concurrent users.
To keep socket locked for the smallest period of time, we split
consume_skb() logic, inlined in skb_free_datagram_locked()
Reported-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/vxy/lksctp-dev
Add missing linux/vmalloc.h include to net/sctp/probe.c
Signed-off-by: David S. Miller <davem@davemloft.net>
|
