| Age | Commit message (Collapse) | Author |
|---|
|
If request firmware fails at init, the code loader DMA allocation
can be NULL, so check for boot complete before freeing up these
resources
Signed-off-by: Dharageswari R <dharageswari.r@intel.com>
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
ASoC: Fixes for v4.6
This is a fairly large collection of fixes but almost all driver
specific ones, especially to the new Intel drivers which have had a lot
of recent development. The one core fix is a change to the debugfs code
to avoid crashes in some relatively unusual configurations.
|
|
We pass struct dw_dma_chip to dw_dma_probe() anyway, thus we may use it to
pass a platform data as well.
While here, constify the source of the platform data.
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
|
|
The mcasp davinci_mcasp_set_dai_fmt function was overriding ahclkx
input/output status that had already been set by the
davinci_mcasp_set_sysclk function. This commit removes clearing
of the ahclkx input/output status from davinci_mcasp_set_dai_fmt.
Signed-off-by: Jim Lodes <jim.lodes@garmin.com>
Signed-off-by: J.D. Schroeder <jay.schroeder@garmin.com>
Acked-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The CCSR_SSI_SOR is a register that clears the TX and/or the RX fifo
on the i.MX SSI port. The fsl_ssi_trigger writes this register in
order to clear the fifo at trigger time.
However, since the CCSR_SSI_SOR register is not in the volatile list,
the caching mechanism prevented the register write in the trigger
function. This caused the fifo to not be cleared (because the value
was unchanged from the last time the register was written), and thus
causes the channels in both TDM or simple I2S mode to slip and be in
the wrong time slots on SSI restart.
This has gone unnoticed for so long because with simple stereo mode,
the consequence is that left and right are swapped, which isn't that
noticeable. However, it's catestrophic in some systems that
require the channels to be in the right slots.
Signed-off-by: Caleb Crome <caleb@crome.org>
Suggested-by: Arnaud Mouiche <arnaud.mouiche@invoxia.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Acked-by: Nicolin Chen <nicoleotsuka@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Default channel map is set for 2 channels. Fix the channel map
based on runtime params to support multichannel.
Signed-off-by: Subhransu S. Prusty <subhransu.s.prusty@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Channel max is changed to 8 from stereo to support multichannel
capability for HDMI devices.
Signed-off-by: Subhransu S. Prusty <subhransu.s.prusty@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
With this patch, chmap controls are created and user space can
set the channel map.
Signed-off-by: Subhransu S. Prusty <subhransu.s.prusty@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
HDMI registers channel map controls per PCM. As PCMs are not
registered during dai_link init callback, store the pcm ids and
codec DAIs during this init callback.
Register for late probe and call the jack_init API which also
registers channel map in the late probe callback handler.
Signed-off-by: Subhransu S. Prusty <subhransu.s.prusty@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
HDMI registers channel map controls per PCM. As PCMs are not
registered during dai_link init callback, store the pcm ids and
codec DAIs during this init callback.
Register for late probe and call the jack_init API which also
registers channel map in the late probe callback handler.
Signed-off-by: Subhransu S. Prusty <subhransu.s.prusty@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
HDMI registers channel map controls per PCM. As PCMs are not
registered during dai_link init callback, store the pcm ids and
codec DAIs during this init callback.
Register for late probe and call the jack_init API which also
registers channel map in the late probe callback handler.
The patch following the machine driver changes adds the channel
map control in the hdac_hdmi codec driver.
Signed-off-by: Subhransu S. Prusty <subhransu.s.prusty@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
To support multichannel hdac hdmi driver registers with HDA
channel map framework. Channel count and channel slot verbs are
programmed by using the chmap helpers/ops. The channel
allocation is then programmed in the audio infoframe as per CEA
spec.
Signed-off-by: Subhransu S. Prusty <subhransu.s.prusty@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
This patch parses ELD speaker allocation data block to find
sink's chmap capability.
Signed-off-by: Subhransu S. Prusty <subhransu.s.prusty@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Signed-off-by: anish kumar <yesanishhere@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Current rsnd_mod_call is counting its calling count to avoid unbalanced
function pair calling for error cases (ex init <-> quit).
SSI parent is now controlled as "mod" on current rsnd driver. Because of
this reason, SSI .remove function will be called twice if it was used as
SSI parent when user tried unbind. But probe/remove pair were not
counted. This patch counts probe/remove functions to avoid it.
Special thans Hiep
Reported-by: Hiep Cao Minh <cm-hiep@jinso.co.jp>
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The bcm2835-i2s driver already has support for the S16_LE format but
that format hasn't been made available because dmaengine_pcm didn't
support packed data transfers.
bcm2835-i2s needs 16-bit left+right channel data to be packed into
a 32-bit word, the FIFO register is 32-bit only and doesn't support
16-bit access.
Now that dmaengine_pcm supports packed transfers the format can
be made available by setting the SND_DMAENGINE_PCM_DAI_FLAG_PACK flag.
No further configuration is necessary:
- snd_dmaengine_dai_dma_data.addr_width is already set to
DMA_SLAVE_BUSWIDTH_4_BYTES to force 32-bit DMA transfers
- dmaengine_pcm will pick up the S16_LE format from the DAI
configuration and make it available since it's no longer
masked out due to the PACK flag.
- there are no further corner cases to catch in hw_params,
since the channel count is fixed at 2 we always have two
16-bit stereo samples that can be transferred via 32-bit DMA
Signed-off-by: Matthias Reichl <hias@horus.com>
Tested-by: Martin Sperl <kernel@martin.sperl.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into asoc-bcm2835
|
|
dmaengine_pcm currently only supports setups where FIFO reads/writes
correspond to exactly one sample, eg 16-bit sample data is transferred
via 16-bit FIFO accesses, 32-bit data via 32-bit accesses.
This patch adds support for setups with fixed width FIFOs where
multiple samples are packed into a larger word.
For example setups with a 32-bit wide FIFO register that expect
16-bit sample transfers to be done with the left+right sample data
packed into a 32-bit word.
Support for packed transfers is controlled via the
SND_DMAENGINE_PCM_DAI_FLAG_PACK flag in snd_dmaengine_dai_dma_data.flags
If this flag is set dmaengine_pcm doesn't put any restriction on the
supported formats and sets the DMA transfer width to undefined.
This means control over the constraints is now transferred to the DAI
driver and it's responsible to provide proper configuration and
check for possible corner cases that aren't handled by the ALSA core.
Signed-off-by: Matthias Reichl <hias@horus.com>
Acked-by: Lars-Peter Clausen <lars@metafoo.de>
Tested-by: Martin Sperl <kernel@martin.sperl.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
If size mismatch of manifest, ABI headers or elements is found, stop
parsing topology info and return the error.
New fields may be append to the tail of ABI objects which will cause
object size to increase. If user space and kernel use different versions
of ABI, size mismatch will be detected here.
Signed-off-by: Mengdong Lin <mengdong.lin@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Stop loading topology info if error happens when creating a widget.
Signed-off-by: Mengdong Lin <mengdong.lin@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The Texas Instruments TAS5720L/M device is a high-efficiency mono
Class-D audio power amplifier optimized for high transient power
capability to use the dynamic power headroom of small loudspeakers.
Its digital time division multiplexed (TDM) interface enables up to
16 devices to share the same bus.
Signed-off-by: Andreas Dannenberg <dannenberg@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Add a function to delete and free the contents of the alg_regions list.
Signed-off-by: Richard Fitzgerald <rf@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Ensure that the wm_adsp driver cleans up when the codec driver
is removed.
Signed-off-by: Richard Fitzgerald <rf@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The patch adds a wm_adsp2_remove() function to ensure that memory
is freed when the driver is unloaded or shut down.
Signed-off-by: Richard Fitzgerald <rf@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Signed-off-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
asoc-linus
|
|
'asoc/fix/hdac', 'asoc/fix/nau8825' and 'asoc/fix/rt5616' into asoc-linus
|
|
|
|
|
|
The bits in the ARIZONA_CLOCK_CONTROL register only respond to writes of
a '1', a write of '0' is ignored. So there's no need to use update_bits.
We can do a simple write to set bits.
Signed-off-by: Richard Fitzgerald <rf@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Initialize the dma_slave_config for PCM DMA transfers,
instead of leaving it uninitialized. Keeps previous data on
the stack from giving us invalid values in uninitialized
members of the config structure.
Signed-off-by: Jim Lodes <jim.lodes@garmin.com>
Signed-off-by: J.D. Schroeder <jay.schroeder@garmin.com>
Acked-by: Jarkko Nikula <jarkko.nikula@bitmer.com>
Reviewed-by: Jarkko Nikula <jarkko.nikula@bitmer.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
This makes the driver use the data pointer added to the gpio_chip
to store a pointer to the state container instead of relying on
container_of().
Cc: Liam Girdwood <lgirdwood@gmail.com>
Cc: alsa-devel@alsa-project.org
Acked-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
This makes the driver use the data pointer added to the gpio_chip
to store a pointer to the state container instead of relying on
container_of().
Cc: Liam Girdwood <lgirdwood@gmail.com>
Cc: alsa-devel@alsa-project.org
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Acked-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
This makes the driver use the data pointer added to the gpio_chip
to store a pointer to the state container instead of relying on
container_of().
Cc: Liam Girdwood <lgirdwood@gmail.com>
Cc: alsa-devel@alsa-project.org
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Acked-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
This makes the driver use the data pointer added to the gpio_chip
to store a pointer to the state container instead of relying on
container_of().
Cc: Liam Girdwood <lgirdwood@gmail.com>
Cc: alsa-devel@alsa-project.org
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Acked-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
This makes the driver use the data pointer added to the gpio_chip
to store a pointer to the state container instead of relying on
container_of().
Cc: Liam Girdwood <lgirdwood@gmail.com>
Cc: alsa-devel@alsa-project.org
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Acked-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
This makes the driver use the data pointer added to the gpio_chip
to store a pointer to the state container instead of relying on
container_of().
Cc: Bard Liao <bardliao@realtek.com>
Cc: Oder Chiou <oder_chiou@realtek.com>
Cc: Liam Girdwood <lgirdwood@gmail.com>
Cc: alsa-devel@alsa-project.org
Acked-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
The IS_ENABLED() macro checks if a Kconfig symbol has been enabled either
built-in or as a module, use that macro instead of open coding the same.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Because LRCK of TDM use High to Low as default setting, this patch
changes the TDM setting to inverse LRCK.
Signed-off-by: PC Liao <pc.liao@mediatek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
RT298_CBJ_CTRL1(0x4f) bit 10 is needed for headset capture. It
will be turned off when "VREF" widget is on and be turned on when
bias level is ON. It is odd. And if "VREF" is turned on in bias
level is ON, RT298_CBJ_CTRL1(0x4f) bit 10 will be turned off.
This patch move the bit control from rt298_set_bias_level and
rt298_vref_event to rt298_jack_detect. So it will be turned on
once a jack is plugged in.
Signed-off-by: Bard Liao <bardliao@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
rt298 need to reset AD filter and the ADC settings will take effort.
Signed-off-by: Bard Liao <bardliao@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
We only need to enable the clock if we are a clock master.
Code ported from bcm2708-i2s driver in Raspberry Pi tree.
Original work by Zoltan Szenczi.
Signed-off-by: Matthias Reichl <hias@horus.com>
Signed-off-by: Martin Sperl <kernel@martin.sperl.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
This adds 24 bit support to the I2S driver of the BCM2835
Code ported from bcm2708-i2s driver in Raspberry Pi tree.
Signed-off-by: Florian Meier <florian.meier@koalo.de>
Signed-off-by: Matthias Reichl <hias@horus.com>
Signed-off-by: Martin Sperl <kernel@martin.sperl.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The expected MCLK frequency ranges and the associated dividers
are updated to improve PLL locking in a corner scenario, with low
MCLK frequency near an input divider change boundary.
Signed-off-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
snd_soc_find_dai() has been exported and so add the kerneldoc comments
for it.
Signed-off-by: Mengdong Lin <mengdong.lin@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Users have reported seeing this false warning on atom driver
[ 5.647469] sst-mfld-platform sst-mfld-platform: Slot control: codec_out tx interleaver slot 0 doesn't have DAPM widget!!!
[ 5.661612] sst-mfld-platform sst-mfld-platform: Slot control: codec_out tx interleaver slot 1 doesn't have DAPM widget!!!
[ 5.661646] sst-mfld-platform sst-mfld-platform: Slot control: codec_out tx interleaver slot 2 doesn't have DAPM widget!!!
[ 5.661681] sst-mfld-platform sst-mfld-platform: Slot control: codec_out tx interleaver slot 3 doesn't have DAPM widget!!!
[ 5.661708] sst-mfld-platform sst-mfld-platform: Slot control: codec_in rx deinterleaver codec_in0_0 doesn't have DAPM widget!!!
[ 5.661738] sst-mfld-platform sst-mfld-platform: Slot control: codec_in rx deinterleaver codec_in0_1 doesn't have DAPM widget!!!
[ 5.661771] sst-mfld-platform sst-mfld-platform: Slot control: codec_in rx deinterleaver codec_in1_0 doesn't have DAPM widget!!!
[ 5.661807] sst-mfld-platform sst-mfld-platform: Slot control: codec_in rx deinterleaver codec_in1_1 doesn't have DAPM widget!!!
This is caused when check for control is not being associated
with a dapm widget, but the check is wrong as the else case
maybe triggered when widget is not powered up, so we should
check if widget is associated before printing this message.
Tested-by: Sandeep Tayal <sandeepx.tayal@intel.com>
Tested-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
ALSA doesn't know about all the different compressed audio formats,
so there is no interface to let userspace enumerate the formats that
are supported by the connected sink. Exporting the raw ELD bytes to
userspace allows an application to select the appropriate audio format
depending on the current capabilities of the connected HDMI sink device.
Usually userspace then just pretends to ALSA that the data is in one of
the raw 16-bit PCM audio formats and relies on the IEC controls to tell
the sink how to interpret the data.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Reviewed-by: Jyri Sarha <jsarha@ti.com>
Tested-by: Jyri Sarha <jsarha@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
This creates pcmC0D2p for the HDMI playback in the same card.
Signed-off-by: Koro Chen <koro.chen@mediatek.com>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
