| Age | Commit message (Collapse) | Author |
|---|
|
DPIB is read currently from a buffer position in memory (indicated by
the registers DPIB[U|L]BASE).Driver reads the position buffer on BDL
completion interrupts to report the DMA position. But the BDL completion
interrupt only indicates the last DMA transfer of the buffer is
completed at the Intel HD Audio subsystem boundary. The periodic DMA
Position-in-Buffer writes may be scheduled at the same time or later
than the MSI and does not guarantee to reflect the position of the last
buffer that was transferred.
Whereas DPIB register in HDA space(vendor specific register indicated by
SDxDPIB) reflects the actual data that is transferred. Hence update the
position based on DPIB for playback.
Signed-off-by: Dharageswari R <dharageswari.r@intel.com>
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Currently on some headsets slight pops can be heard during DAPM
power-up/down. This can also be witnessed during the HP detect
procedure. This patch addresses the issue by adjusting DAPM power
sequencing slightly, the introduction of delays and use of
minimum HP gain to avoid such noise artefacts.
Signed-off-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The set_bias_level toggles the PDN signal when entering
SND_SOC_BIAS_STANDBY and SND_SOC_BIAS_OFF. However this has no effect and
actually breaks things down (tested with TAS5717) due to the following
reasons:
1) holding down PDN does not save power but holding down RST does
2) now hard mute via register 0x5 is implemented and therefore it is no
longer needed to toggle PDN to enter all channel shut down
3) in order to leave PDN it is required to toggle the RST signal (see
TAS5721 datasheet), which was not implemented
4) toggling PDN as implemented actually mutes PWMs and there is no audio
output (tested on TAS5717)
For these reasons remove the PDN signal toggling and just initialize it to
inactive in probe().
Signed-off-by: Petr Kulhavy <brain@jikos.cz>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
TAS5721 datasheet recommends to wait at least 13.5ms after deasserting the
RESET signal. For TAS5717 this time is only 12ms, which was the original
value in the code.
Extend the wait time after deasserting RESET from 12 to 13.5ms to comply
with the TAS5721 specification.
Signed-off-by: Petr Kulhavy <brain@jikos.cz>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Channel 1 and 2 Mixer Volume controls (registers 0x72/0x73 and 0x76/0x77)
were wrongly assigned to tas5711_controls in commit f252d2346022
("ASoC: tas571x: add input channel mixer for TAS5717/19")
Therefore move them to tas5717_controls.
Signed-off-by: Petr Kulhavy <brain@jikos.cz>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Wait extra 50ms after writing the oscillator trim register in probe(), as
recommended by the TAS5721 and TAS5711 datasheets.
Signed-off-by: Petr Kulhavy <brain@jikos.cz>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into for-next
ASoC: Updates for v4.9
Apart from the cleanups done by Morimoto-san this has very much been a
driver focused release with very little generic change:
- A big factoring out of the simple-card code to allow it to be shared
more with the rcar generic card from Kuninori Morimoto.
- Removal of some operations duplicated on the CODEC level, again by
Kuninori Morimoto.
- Lots more machine support for x86 systems.
- New drivers for Nuvoton NAU88C10, Realtek RT5660 and RT5663.
|
|
'asoc/topic/wm8960', 'asoc/topic/wm8962' and 'asoc/topic/wm8991' into asoc-next
|
|
'asoc/topic/tlv320aic31xx', 'asoc/topic/tlv320dac33' and 'asoc/topic/topology' into asoc-next
|
|
'asoc/topic/stac9766', 'asoc/topic/sti' and 'asoc/topic/sunxi' into asoc-next
|
|
'asoc/topic/rt5677' and 'asoc/topic/samsung' into asoc-next
|
|
'asoc/topic/rt5616' into asoc-next
|
|
'asoc/topic/omap' and 'asoc/topic/platform-drvdata' into asoc-next
|
|
'asoc/topic/max98926' and 'asoc/topic/mtk' into asoc-next
|
|
'asoc/topic/gpio-chip' and 'asoc/topic/hdmi' into asoc-next
|
|
'asoc/topic/dpcm' into asoc-next
|
|
'asoc/topic/cs53l30' and 'asoc/topic/da7213' into asoc-next
|
|
'asoc/topic/arizona', 'asoc/topic/atmel' and 'asoc/topic/codec-component' into asoc-next
|
|
|
|
|
|
|
|
|
|
|
|
'asoc/fix/nau8825', 'asoc/fix/rt5514' and 'asoc/fix/shift' into asoc-linus
|
|
|
|
|
|
The recent series of changes to the caching in the SSI driver have
caused a number of problems to appear in some test systems. These are
still not fully understood but we're coming up to the merge window so
for now let's revert commit 7de2763d9b3 (ASoC: fsl_ssi: Remove
.num_reg_defaults_raw from regmap_config) as backing that out seems to
resolve the problem on affected systems.
Reported-by: Maciej S. Szmigiero" <mail@maciej.szmigiero.name>
Signed-off-by: Mark Brown <broonie@kernel.org>
Reviewed-by: Marek Vasut <marex@denx.de>
|
|
Currently there is a memory leak of module on a ENOMEM return path.
Fix this by kfree'ing module before returning.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
This patch adds SNDRV_PCM_TRIGGER_SUSPEND/RESUME.
Otherwise, it breaks rsnd driver internal start/stop counter
when suspend/resume. This issue was reported/tested by Hiep
Tested-by: Hiep Cao Minh <cm-hiep@jinso.co.jp>
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
|
|
TLV_DB_RANGE_HEAD macro was obsoleted by commit bf1d1c9b6179 ("ALSA: tlv:
add DECLARE_TLV_DB_RANGE()").
This commit removes usage of the macro, with the obsoleting macro renamed
to SNDRV_CTL_TLVD_DECLARE_DB_RANGE().
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
TLV_DB_RANGE_HEAD macro was obsoleted by commit bf1d1c9b6179 ("ALSA: tlv:
add DECLARE_TLV_DB_RANGE()").
This commit removes usage of the macro, with the obsoleting macro renamed
to SNDRV_CTL_TLVD_DECLARE_DB_RANGE().
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
TLV_DB_RANGE_HEAD macro was obsoleted by commit bf1d1c9b6179 ("ALSA: tlv:
add DECLARE_TLV_DB_RANGE()").
This commit removes usage of the macro, with the obsoleting macro renamed
to SNDRV_CTL_TLVD_DECLARE_DB_RANGE().
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Do s/ststem/system/ .
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Sparse reports a below warning.
sound/soc/codecs/da7219.c:804:57: warning: dubious: x & !y
The line includes a condition statement; '(a < b) & !c'. Practically, the
evaluated value of this statement equals to the value of '(a < b) && !c'.
Although, it's not an usual way to use bitwise operations as logical
operations to several conditions.
This commit fixes the bug.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Acked-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
This hardware supports only 2-channel DAI, even mono ADC digital output
has two channels with the same data.
Having min_channels=1 results in broken playback of mono files in setups
where CPU DAI supports mono.
Signed-off-by: Nikita Yushchenko <nikita.yoush@cogentembedded.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
As long as reading datasheet of STAC9766/9767, this driver includes wrong
usage of DECLARE_TLV_DB_LINEAR().
In "8.1.2. Master Volume Registers", attenuation of lineout volumes is
represented in 5 bits by -1.5 dB/step from 0 to -46.5 dB. Thus,
'master_tlv' should be dB step representation.
In "8.1.14. Record Gain", gain of volumes is represented in 4 bits by
1.5 dB/step from 0 to 22.5 dB. Thus, 'record_tlv' should be dB step
representation.
In "8.1.5. PC BEEP Volume", attenuation of volume is represented in 4 bits
by -3 dB/step from 0 to 45 dB. Thus, 'beep_tlv' should be dB step
representation.
In "8.1.7. Stereo or Mic Volume" and so on, gain of volumes is represented
in 5 bits by -1.5 dB from 12 to -34.5 dB. Thus, 'mix_tlv' should be dB
step representation.
Totally, current implementation includes misuse of TLV-related macro.
This commit replaces usage of DECLARE_TLV_DB_LINEAR() with
SNDRV_CTL_TLVD_DECLARE_DB_SCALE(), to give proper information to
applications in user land.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
This driver has some unused variables. They should be removed.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
As long as reading datasheet of WM8991, this driver includes wrong usage
of DECLARE_TLV_DB_LINEAR().
In "Table 6 Input PGA Volume Range", volume is represented in 5 bits by
1.5 dB/step between -16.5/30.0 dB. Thus, 'in_pga_tlv' should be dB step
representation.
In "Table 34 LOMIX and ROMIX Volume Range", volume is represented in three
bits by -3 dB/step from 0 to -21 dB. Thus, 'out_mix_tlv' should be dB step
represenation.
In "Table 36 LOPGA, ROPGA, LOUT, ROUT and SPKVOL Volume Range", volume is
represented in 7 bits by 1 dB/step from -73 to 6 dB, including mute. Thus,
'out_pga_tlv' should be dB step representation.
In "Table 26 Digital Volume Range", volume is represented in 8 bits by
3/8 dB/step from -71.625 to 0 dB. Thus, 'out_dac_tlv' should be dB step
representation.
In "Table 16 ADC Digital Volume Range", volume is represented in 8 bits by
3/8 dB/step from -71.625 to 17.625 dB. Thus, 'in_adc_tlv' should be dB step
representation.
In "Table 23 Digital Sidetone Volume", volume is represented in 5 bits by
3 dB/step from -36 to 0 dB. Thus, 'out_sidetone_tlv' should be dB step
representation.
In "Table 12 Left Input Mixer Volume Control", volume is represented in
3 bits by 3 dB/step from -12 to 6 dB
Totally, current implementation includes misuse of TLV-related macro.
This commit replaces usage of DECLARE_TLV_DB_LINEAR() with proper macros,
to give proper information to applications in user land.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Sparse reports a below warning.
tpa6130a2.c:193:33: warning: symbol 'tpa6130a2_component_driver' was not declared. Should it be static?
The symbol is just used inner the file. Forthermore, it's constant. Thus,
it's better to add static and const qualifier.
This commit adds it.
Fixes: cb7e62256e99 (ASoC: tpa6130a2: Register component)
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Sparse reports below warnings.
bxt_rt298.c:275:9: warning: obsolete array initializer, use C99 syntax
bxt_rt298.c:290:9: warning: obsolete array initializer, use C99 syntax
bxt_rt298.c:304:9: warning: obsolete array initializer, use C99 syntax
bxt_rt298.c:317:9: warning: obsolete array initializer, use C99 syntax
bxt_rt298.c:331:9: warning: obsolete array initializer, use C99 syntax
bxt_rt298.c:344:9: warning: obsolete array initializer, use C99 syntax
bxt_rt298.c:357:9: warning: obsolete array initializer, use C99 syntax
There's no need to use obsoleted way. This commit fixes it.
Fixes: 76016322ec56 (ASoC: Intel: Add Broxton-P machine driver)
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Sparse reports below warnings.
bxt_da7219_max98357a.c:250:9: warning: obsolete array initializer, use C99 syntax
bxt_da7219_max98357a.c:275:9: warning: obsolete array initializer, use C99 syntax
bxt_da7219_max98357a.c:290:9: warning: obsolete array initializer, use C99 syntax
bxt_da7219_max98357a.c:304:9: warning: obsolete array initializer, use C99 syntax
bxt_da7219_max98357a.c:317:9: warning: obsolete array initializer, use C99 syntax
There's no need to use obsoleted way. This commit fixes it.
Fixes: 723bad3fef8b (ASoC: Intel: Add Broxton-P Dialog Maxim machine driver)
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Sparse reports below warnings.
rt5616.c:1270:24: warning: symbol 'rt5616_aif_dai_ops' was not declared. Should it be static?
rt5616.c:1277:27: warning: symbol 'rt5616_dai' was not declared. Should it be static?
These two symbols are just used inner the file, thus it's better to add
static qualifier.
This commit adds it.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The later Arizona parts do run write sequences to power up and down the
speaker path as such a delay needs to be inserted into the DAPM sequence
to allow this to run. This patch adds appropriate delays into the
existing coalesced delay scheme.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
When debugging it is useful to check the total power up/down delay that
is executed as part of the coalesced output delay. This patch adds some
debug prints for this.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
HP Spectre x360 with CX20724 codec has two speaker outputs while the
BIOS sets up only the bottom one (NID 0x17) and disables the top one
(NID 0x1d).
This patch adds a fixup simply defining the proper pincfg for NID 0x1d
so that the top speaker works as is.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=169071
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Add channel and rate constraints for Refcap and dmiccap devices
respectively.
Signed-off-by: Yong Zhi <yong.zhi@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
When operating the BE, we should print out the dai_link name of BE other
than FE. This is useful when analyzing the kernel log.
Signed-off-by: Donglin Peng <pengdonglin@smartisan.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
tlv320dac31xx is a subset of tlv320aic31xx:
- it does not have MIC inputs and ADC, thus capture is not supported,
- it has analog inputs AIN1/AIN2 that can be mixed into output.
Although tlv320dac31xx does work with tlv320aic31xx driver, this setup
does register non-existent widgets and non-existent capture stream.
Thus userspace lists non-existent objects in user interfaces, an can
access these, causing operations with device registers that are
declared as "reserved" in tlv320dac31xx datasheet.
This patch fixes this situation by separating controls/widgets/routes
into common, aic31xx-specific, and dac31xx-specific parts. Only parts
that match actual hardware (as declared in "compatible" device tree
property) are registered.
Changes from v1:
- update device tree binding documentation,
- rebased on top of "ASoC: codec duplicated callback function goes to
component on tlv320aic31xx" commit.
Signed-off-by: Nikita Yushchenko <nikita.yoush@cogentembedded.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Currently if AAD is enabled in the device, during system suspend
the feature remains, regardless of whether the codec is a wake-up
source or not. This means some additional power is being used
which is unnecessary, and can causes issues with some platforms'
IRQ handlers where state changes during system suspend aren't
captured.
This patch updates the driver to disable AAD during suspend, if
we're not a wake-up source, and then re-enables this on resume.
Signed-off-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
