Merge tag 'devfreq-next-for-5.19' of git://git.kernel.org/pub/scm/linux/kernel/git/chanwoo/linux

Pull devfreq changes for 5.19-rc1 from Chanwoo Choi:

"1. Update devfreq core

 - Add cpu based scaling support to passive governor. Some device like
   cache might require the dynamic frequency scaling. But, it has very
   tightly to cpu frequency. So that use passive governor to scale
   the frequency according to current cpu frequency.

  To decide the frequency of the device, the governor does one of the following:
  : Derives the optimal devfreq device opp from required-opps property of
    the parent cpu opp_table.

  : Scales the device frequency in proportion to the CPU frequency. So, if
    the CPUs are running at their max frequency, the device runs at its
    max frequency. If the CPUs are running at their min frequency, the
    device runs at its min frequency. It is interpolated for frequencies
    in between.

 2. Update devfreq drivers

  - Update rk3399_dmc.c as following:

   : Convert dt-binding document to YAML and deprecate unused properties.

   : Use Hz units for the device-tree properties of rk3399_dmc.

   : rk3399_dmc is able to set the idle time before changing the dmc clock.
     Specify idle time parameters by using nano-second unit on dt bidning.

   : Add new disable-freq properties to optimize the power-saving feature
     of rk3399_dmc.

   : Disable devfreq-event device on remove() to fix unbalanced
     enable-disable count.

   : Use devm_pm_opp_of_add_table()

   : Block PMU (Power-Management Unit) transitions when scaling frequency
     by ARM Trust Firmware in order to fix the conflict between PMU and DMC
     (Dynamic Memory Controller)."

* tag 'devfreq-next-for-5.19' of git://git.kernel.org/pub/scm/linux/kernel/git/chanwoo/linux:
  PM / devfreq: passive: Keep cpufreq_policy for possible cpus
  PM / devfreq: passive: Reduce duplicate code when passive_devfreq case
  PM / devfreq: Add cpu based scaling support to passive governor
  PM / devfreq: Export devfreq_get_freq_range symbol within devfreq
  PM / devfreq: rk3399_dmc: Block PMU during transitions
  soc: rockchip: power-domain: Manage resource conflicts with firmware
  PM / devfreq: rk3399_dmc: Avoid static (reused) profile
  PM / devfreq: rk3399_dmc: Use devm_pm_opp_of_add_table()
  PM / devfreq: rk3399_dmc: Disable edev on remove()
  PM / devfreq: rk3399_dmc: Support new *-ns properties
  PM / devfreq: rk3399_dmc: Support new disable-freq properties
  PM / devfreq: rk3399_dmc: Use bitfield macro definitions for ODT_PD
  PM / devfreq: rk3399_dmc: Drop excess timing properties
  PM / devfreq: rk3399_dmc: Drop undocumented ondemand DT props
  dt-bindings: devfreq: rk3399_dmc: Add more disable-freq properties
  dt-bindings: devfreq: rk3399_dmc: Specify idle params in nanoseconds
  dt-bindings: devfreq: rk3399_dmc: Fix Hz units
  dt-bindings: devfreq: rk3399_dmc: Deprecate unused/redundant properties
  dt-bindings: devfreq: rk3399_dmc: Convert to YAML

1 files changed, 0 insertions, 212 deletions

diff --git a/Documentation/devicetree/bindings/devfreq/rk3399_dmc.txt b/Documentation/devicetree/bindings/devfreq/rk3399_dmc.txt
deleted file mode 100644
index 58fc8a6cebc7..000000000000
--- a/Documentation/devicetree/bindings/devfreq/rk3399_dmc.txt
+++ /dev/null
@@ -1,212 +0,0 @@
-* Rockchip rk3399 DMC (Dynamic Memory Controller) device
-
-Required properties:
-- compatible:		 Must be "rockchip,rk3399-dmc".
-- devfreq-events:	 Node to get DDR loading, Refer to
-			 Documentation/devicetree/bindings/devfreq/event/
-			 rockchip-dfi.txt
-- clocks:		 Phandles for clock specified in "clock-names" property
-- clock-names :		 The name of clock used by the DFI, must be
-			 "pclk_ddr_mon";
-- operating-points-v2:	 Refer to Documentation/devicetree/bindings/opp/opp-v2.yaml
-			 for details.
-- center-supply:	 DMC supply node.
-- status:		 Marks the node enabled/disabled.
-- rockchip,pmu:		 Phandle to the syscon managing the "PMU general register
-			 files".
-
-Optional properties:
-- interrupts:		 The CPU interrupt number. The interrupt specifier
-			 format depends on the interrupt controller.
-			 It should be a DCF interrupt. When DDR DVFS finishes
-			 a DCF interrupt is triggered.
-- rockchip,pmu:		 Phandle to the syscon managing the "PMU general register
-			 files".
-
-Following properties relate to DDR timing:
-
-- rockchip,dram_speed_bin :	  Value reference include/dt-bindings/clock/rk3399-ddr.h,
-				  it selects the DDR3 cl-trp-trcd type. It must be
-				  set according to "Speed Bin" in DDR3 datasheet,
-				  DO NOT use a smaller "Speed Bin" than specified
-				  for the DDR3 being used.
-
-- rockchip,pd_idle :		  Configure the PD_IDLE value. Defines the
-				  power-down idle period in which memories are
-				  placed into power-down mode if bus is idle
-				  for PD_IDLE DFI clock cycles.
-
-- rockchip,sr_idle :		  Configure the SR_IDLE value. Defines the
-				  self-refresh idle period in which memories are
-				  placed into self-refresh mode if bus is idle
-				  for SR_IDLE * 1024 DFI clock cycles (DFI
-				  clocks freq is half of DRAM clock), default
-				  value is "0".
-
-- rockchip,sr_mc_gate_idle :	  Defines the memory self-refresh and controller
-				  clock gating idle period. Memories are placed
-				  into self-refresh mode and memory controller
-				  clock arg gating started if bus is idle for
-				  sr_mc_gate_idle*1024 DFI clock cycles.
-
-- rockchip,srpd_lite_idle :	  Defines the self-refresh power down idle
-				  period in which memories are placed into
-				  self-refresh power down mode if bus is idle
-				  for srpd_lite_idle * 1024 DFI clock cycles.
-				  This parameter is for LPDDR4 only.
-
-- rockchip,standby_idle :	  Defines the standby idle period in which
-				  memories are placed into self-refresh mode.
-				  The controller, pi, PHY and DRAM clock will
-				  be gated if bus is idle for standby_idle * DFI
-				  clock cycles.
-
-- rockchip,dram_dll_dis_freq :	  Defines the DDR3 DLL bypass frequency in MHz.
-				  When DDR frequency is less than DRAM_DLL_DISB_FREQ,
-				  DDR3 DLL will be bypassed. Note: if DLL was bypassed,
-				  the odt will also stop working.
-
-- rockchip,phy_dll_dis_freq :	  Defines the PHY dll bypass frequency in
-				  MHz (Mega Hz). When DDR frequency is less than
-				  DRAM_DLL_DISB_FREQ, PHY DLL will be bypassed.
-				  Note: PHY DLL and PHY ODT are independent.
-
-- rockchip,ddr3_odt_dis_freq :	  When the DRAM type is DDR3, this parameter defines
-				  the ODT disable frequency in MHz (Mega Hz).
-				  when the DDR frequency is  less then ddr3_odt_dis_freq,
-				  the ODT on the DRAM side and controller side are
-				  both disabled.
-
-- rockchip,ddr3_drv :		  When the DRAM type is DDR3, this parameter defines
-				  the DRAM side driver strength in ohms. Default
-				  value is 40.
-
-- rockchip,ddr3_odt :		  When the DRAM type is DDR3, this parameter defines
-				  the DRAM side ODT strength in ohms. Default value
-				  is 120.
-
-- rockchip,phy_ddr3_ca_drv :	  When the DRAM type is DDR3, this parameter defines
-				  the phy side CA line (incluing command line,
-				  address line and clock line) driver strength.
-				  Default value is 40.
-
-- rockchip,phy_ddr3_dq_drv :	  When the DRAM type is DDR3, this parameter defines
-				  the PHY side DQ line (including DQS/DQ/DM line)
-				  driver strength. Default value is 40.
-
-- rockchip,phy_ddr3_odt : 	  When the DRAM type is DDR3, this parameter defines
-				  the PHY side ODT strength. Default value is 240.
-
-- rockchip,lpddr3_odt_dis_freq : When the DRAM type is LPDDR3, this parameter defines
-				  then ODT disable frequency in MHz (Mega Hz).
-				  When DDR frequency is less then ddr3_odt_dis_freq,
-				  the ODT on the DRAM side and controller side are
-				  both disabled.
-
-- rockchip,lpddr3_drv :		  When the DRAM type is LPDDR3, this parameter defines
-				  the DRAM side driver strength in ohms. Default
-				  value is 34.
-
-- rockchip,lpddr3_odt :		  When the DRAM type is LPDDR3, this parameter defines
-				  the DRAM side ODT strength in ohms. Default value
-				  is 240.
-
-- rockchip,phy_lpddr3_ca_drv :	  When the DRAM type is LPDDR3, this parameter defines
-				  the PHY side CA line (including command line,
-				  address line and clock line) driver strength.
-				  Default value is 40.
-
-- rockchip,phy_lpddr3_dq_drv :	  When the DRAM type is LPDDR3, this parameter defines
-				  the PHY side DQ line (including DQS/DQ/DM line)
-				  driver strength. Default value is 40.
-
-- rockchip,phy_lpddr3_odt : 	  When dram type is LPDDR3, this parameter define
-				  the phy side odt strength, default value is 240.
-
-- rockchip,lpddr4_odt_dis_freq : When the DRAM type is LPDDR4, this parameter
-				  defines the ODT disable frequency in
-				  MHz (Mega Hz). When the DDR frequency is less then
-				  ddr3_odt_dis_freq, the ODT on the DRAM side and
-				  controller side are both disabled.
-
-- rockchip,lpddr4_drv :		  When the DRAM type is LPDDR4, this parameter defines
-				  the DRAM side driver strength in ohms. Default
-				  value is 60.
-
-- rockchip,lpddr4_dq_odt : 	  When the DRAM type is LPDDR4, this parameter defines
-				  the DRAM side ODT on DQS/DQ line strength in ohms.
-				  Default value is 40.
-
-- rockchip,lpddr4_ca_odt :	  When the DRAM type is LPDDR4, this parameter defines
-				  the DRAM side ODT on CA line strength in ohms.
-				  Default value is 40.
-
-- rockchip,phy_lpddr4_ca_drv :	  When the DRAM type is LPDDR4, this parameter defines
-				  the PHY side CA line (including command address
-				  line) driver strength. Default value is 40.
-
-- rockchip,phy_lpddr4_ck_cs_drv : When the DRAM type is LPDDR4, this parameter defines
-				  the PHY side clock line and CS line driver
-				  strength. Default value is 80.
-
-- rockchip,phy_lpddr4_dq_drv :	  When the DRAM type is LPDDR4, this parameter defines
-				  the PHY side DQ line (including DQS/DQ/DM line)
-				  driver strength. Default value is 80.
-
-- rockchip,phy_lpddr4_odt :	  When the DRAM type is LPDDR4, this parameter defines
-				  the PHY side ODT strength. Default value is 60.
-
-Example:
-	dmc_opp_table: dmc_opp_table {
-		compatible = "operating-points-v2";
-
-		opp00 {
-			opp-hz = /bits/ 64 <300000000>;
-			opp-microvolt = <900000>;
-		};
-		opp01 {
-			opp-hz = /bits/ 64 <666000000>;
-			opp-microvolt = <900000>;
-		};
-	};
-
-	dmc: dmc {
-		compatible = "rockchip,rk3399-dmc";
-		devfreq-events = <&dfi>;
-		interrupts = <GIC_SPI 1 IRQ_TYPE_LEVEL_HIGH>;
-		clocks = <&cru SCLK_DDRC>;
-		clock-names = "dmc_clk";
-		operating-points-v2 = <&dmc_opp_table>;
-		center-supply = <&ppvar_centerlogic>;
-		upthreshold = <15>;
-		downdifferential = <10>;
-		rockchip,ddr3_speed_bin = <21>;
-		rockchip,pd_idle = <0x40>;
-		rockchip,sr_idle = <0x2>;
-		rockchip,sr_mc_gate_idle = <0x3>;
-		rockchip,srpd_lite_idle	= <0x4>;
-		rockchip,standby_idle = <0x2000>;
-		rockchip,dram_dll_dis_freq = <300>;
-		rockchip,phy_dll_dis_freq = <125>;
-		rockchip,auto_pd_dis_freq = <666>;
-		rockchip,ddr3_odt_dis_freq = <333>;
-		rockchip,ddr3_drv = <40>;
-		rockchip,ddr3_odt = <120>;
-		rockchip,phy_ddr3_ca_drv = <40>;
-		rockchip,phy_ddr3_dq_drv = <40>;
-		rockchip,phy_ddr3_odt = <240>;
-		rockchip,lpddr3_odt_dis_freq = <333>;
-		rockchip,lpddr3_drv = <34>;
-		rockchip,lpddr3_odt = <240>;
-		rockchip,phy_lpddr3_ca_drv = <40>;
-		rockchip,phy_lpddr3_dq_drv = <40>;
-		rockchip,phy_lpddr3_odt = <240>;
-		rockchip,lpddr4_odt_dis_freq = <333>;
-		rockchip,lpddr4_drv = <60>;
-		rockchip,lpddr4_dq_odt = <40>;
-		rockchip,lpddr4_ca_odt = <40>;
-		rockchip,phy_lpddr4_ca_drv = <40>;
-		rockchip,phy_lpddr4_ck_cs_drv = <80>;
-		rockchip,phy_lpddr4_dq_drv = <80>;
-		rockchip,phy_lpddr4_odt = <60>;
-	};