Merge tag 'drm-misc-next-2018-01-08' of git://anongit.freedesktop.org/drm/drm-misc into drm-next

drm-misc-next for 4.16:

Cross-subsystem Changes:

- some dt-binding changes for Ilitek and sun4i devices

Core Changes:

- panel_orientation_quirks: fix tainted kernel

Driver Changes:

- panel changes
- A83T and LVDS support to sun4i

* tag 'drm-misc-next-2018-01-08' of git://anongit.freedesktop.org/drm/drm-misc:
  drm/panel: lvds: Add support for the power-supply property
  dt-bindings: panel: lvds: Document power-supply property
  drm/sun4i: Add A83T support
  drm/sun4i: Add LVDS support
  drm/sun4i: Create minimal multipliers and dividers
  drm/sun4i: Force the mixer rate at 150MHz
  dt-bindings: display: sun4i-drm: Add A83T pipeline
  dt-bindings: display: sun4i-drm: Add LVDS properties
  drm/tinydrm: add driver for ST7735R panels
  dt-bindings: Add binding for Sitronix ST7735R display panels
  dt-bindings: add jianda vendor prefix
  drm/tinydrm: Update ILI9225 compatible string
  dt-bindings: update compatible string for ILI9225
  dt-bindings: Add "vot" vendor prefix
  drm: fix tainted kernel caused by drm_panel_orientation_quirks.c
  drm/panel: Add Ilitek ILI9322 driver
  drm/panel: Add DT bindings for Ilitek ILI9322

7 files changed, 109 insertions, 3 deletions

diff --git a/Documentation/devicetree/bindings/display/ilitek,ili9225.txt b/Documentation/devicetree/bindings/display/ilitek,ili9225.txt
index 21607a541c33..a59feb52015b 100644
--- a/Documentation/devicetree/bindings/display/ilitek,ili9225.txt
+++ b/Documentation/devicetree/bindings/display/ilitek,ili9225.txt
@@ -4,7 +4,7 @@ This binding is for display panels using an Ilitek ILI9225 controller in SPI
 mode.
 
 Required properties:
-- compatible:	"ilitek,ili9225-2.2in-176x220"
+- compatible:	"vot,v220hf01a-t", "ilitek,ili9225"
 - rs-gpios:	Register select signal
 - reset-gpios:	Reset pin
 
@@ -16,7 +16,7 @@ Optional properties:
 
 Example:
 	display@0{
-		compatible = "ilitek,ili9225-2.2in-176x220";
+		compatible = "vot,v220hf01a-t", "ilitek,ili9225";
 		reg = <0>;
 		spi-max-frequency = <12000000>;
 		rs-gpios = <&gpio0 9 GPIO_ACTIVE_HIGH>;
diff --git a/Documentation/devicetree/bindings/display/panel/ilitek,ili9322.txt b/Documentation/devicetree/bindings/display/panel/ilitek,ili9322.txt
new file mode 100644
index 000000000000..3d5ce6ad6ec7
--- /dev/null
+++ b/Documentation/devicetree/bindings/display/panel/ilitek,ili9322.txt
@@ -0,0 +1,49 @@
+Ilitek ILI9322 TFT panel driver with SPI control bus
+
+This is a driver for 320x240 TFT panels, accepting a variety of input
+streams that get adapted and scaled to the panel. The panel output has
+960 TFT source driver pins and 240 TFT gate driver pins, VCOM, VCOML and
+VCOMH outputs.
+
+Required properties:
+  - compatible: "dlink,dir-685-panel", "ilitek,ili9322"
+    (full system-specific compatible is always required to look up configuration)
+  - reg: address of the panel on the SPI bus
+
+Optional properties:
+  - vcc-supply: core voltage supply, see regulator/regulator.txt
+  - iovcc-supply: voltage supply for the interface input/output signals,
+    see regulator/regulator.txt
+  - vci-supply: voltage supply for analog parts, see regulator/regulator.txt
+  - reset-gpios: a GPIO spec for the reset pin, see gpio/gpio.txt
+
+  The following optional properties only apply to RGB and YUV input modes and
+  can be omitted for BT.656 input modes:
+
+  - pixelclk-active: see display/panel/display-timing.txt
+  - de-active: see display/panel/display-timing.txt
+  - hsync-active: see display/panel/display-timing.txt
+  - vsync-active: see display/panel/display-timing.txt
+
+The panel must obey the rules for a SPI slave device as specified in
+spi/spi-bus.txt
+
+The device node can contain one 'port' child node with one child
+'endpoint' node, according to the bindings defined in
+media/video-interfaces.txt. This node should describe panel's video bus.
+
+Example:
+
+panel: display@0 {
+	compatible = "dlink,dir-685-panel", "ilitek,ili9322";
+	reg = <0>;
+	vcc-supply = <&vdisp>;
+	iovcc-supply = <&vdisp>;
+	vci-supply = <&vdisp>;
+
+	port {
+		panel_in: endpoint {
+			remote-endpoint = <&display_out>;
+		};
+	};
+};
diff --git a/Documentation/devicetree/bindings/display/panel/panel-common.txt b/Documentation/devicetree/bindings/display/panel/panel-common.txt
index ec52c472c845..557fa765adcb 100644
--- a/Documentation/devicetree/bindings/display/panel/panel-common.txt
+++ b/Documentation/devicetree/bindings/display/panel/panel-common.txt
@@ -78,6 +78,16 @@ used for panels that implement compatible control signals.
   while active. Active high reset signals can be supported by inverting the
   GPIO specifier polarity flag.
 
+Power
+-----
+
+- power-supply: display panels require power to be supplied. While several
+  panels need more than one power supply with panel-specific constraints
+  governing the order and timings of the power supplies, in many cases a single
+  power supply is sufficient, either because the panel has a single power rail,
+  or because all its power rails can be driven by the same supply. In that case
+  the power-supply property specifies the supply powering the panel as a phandle
+  to a regulator.
 
 Backlight
 ---------
diff --git a/Documentation/devicetree/bindings/display/panel/panel-lvds.txt b/Documentation/devicetree/bindings/display/panel/panel-lvds.txt
index b938269f841e..250850a2150b 100644
--- a/Documentation/devicetree/bindings/display/panel/panel-lvds.txt
+++ b/Documentation/devicetree/bindings/display/panel/panel-lvds.txt
@@ -32,6 +32,7 @@ Optional properties:
 - label: See panel-common.txt.
 - gpios: See panel-common.txt.
 - backlight: See panel-common.txt.
+- power-supply: See panel-common.txt.
 - data-mirror: If set, reverse the bit order described in the data mappings
   below on all data lanes, transmitting bits for slots 6 to 0 instead of
   0 to 6.
diff --git a/Documentation/devicetree/bindings/display/panel/simple-panel.txt b/Documentation/devicetree/bindings/display/panel/simple-panel.txt
index 1341bbf4aa3d..16d8ff088b7d 100644
--- a/Documentation/devicetree/bindings/display/panel/simple-panel.txt
+++ b/Documentation/devicetree/bindings/display/panel/simple-panel.txt
@@ -1,7 +1,7 @@
 Simple display panel
 
 Required properties:
-- power-supply: regulator to provide the supply voltage
+- power-supply: See panel-common.txt
 
 Optional properties:
 - ddc-i2c-bus: phandle of an I2C controller used for DDC EDID probing
diff --git a/Documentation/devicetree/bindings/display/sitronix,st7735r.txt b/Documentation/devicetree/bindings/display/sitronix,st7735r.txt
new file mode 100644
index 000000000000..f0a5090a3326
--- /dev/null
+++ b/Documentation/devicetree/bindings/display/sitronix,st7735r.txt
@@ -0,0 +1,35 @@
+Sitronix ST7735R display panels
+
+This binding is for display panels using a Sitronix ST7735R controller in SPI
+mode.
+
+Required properties:
+- compatible:	"jianda,jd-t18003-t01", "sitronix,st7735r"
+- dc-gpios:	Display data/command selection (D/CX)
+- reset-gpios:	Reset signal (RSTX)
+
+The node for this driver must be a child node of a SPI controller, hence
+all mandatory properties described in ../spi/spi-bus.txt must be specified.
+
+Optional properties:
+- rotation:	panel rotation in degrees counter clockwise (0,90,180,270)
+- backlight:	phandle of the backlight device attached to the panel
+
+Example:
+
+	backlight: backlight {
+		compatible = "gpio-backlight";
+		gpios = <&gpio 44 GPIO_ACTIVE_HIGH>;
+	}
+
+	...
+
+	display@0{
+		compatible = "jianda,jd-t18003-t01", "sitronix,st7735r";
+		reg = <0>;
+		spi-max-frequency = <32000000>;
+		dc-gpios = <&gpio 43 GPIO_ACTIVE_HIGH>;
+		reset-gpios = <&gpio 80 GPIO_ACTIVE_HIGH>;
+		rotation = <270>;
+		backlight = &backlight;
+	};
diff --git a/Documentation/devicetree/bindings/display/sunxi/sun4i-drm.txt b/Documentation/devicetree/bindings/display/sunxi/sun4i-drm.txt
index 50cc72ee1168..cd626ee1147a 100644
--- a/Documentation/devicetree/bindings/display/sunxi/sun4i-drm.txt
+++ b/Documentation/devicetree/bindings/display/sunxi/sun4i-drm.txt
@@ -93,6 +93,7 @@ Required properties:
    * allwinner,sun6i-a31s-tcon
    * allwinner,sun7i-a20-tcon
    * allwinner,sun8i-a33-tcon
+   * allwinner,sun8i-a83t-tcon-lcd
    * allwinner,sun8i-v3s-tcon
  - reg: base address and size of memory-mapped region
  - interrupts: interrupt associated to this IP
@@ -121,6 +122,14 @@ Required properties:
 On SoCs other than the A33 and V3s, there is one more clock required:
    - 'tcon-ch1': The clock driving the TCON channel 1
 
+On SoCs that support LVDS (all SoCs but the A13, H3, H5 and V3s), you
+need one more reset line:
+   - 'lvds': The reset line driving the LVDS logic
+
+And on the A23, A31, A31s and A33, you need one more clock line:
+   - 'lvds-alt': An alternative clock source, separate from the TCON channel 0
+                 clock, that can be used to drive the LVDS clock
+
 DRC
 ---
 
@@ -216,6 +225,7 @@ supported.
 
 Required properties:
   - compatible: value must be one of:
+    * allwinner,sun8i-a83t-de2-mixer-0
     * allwinner,sun8i-v3s-de2-mixer
   - reg: base address and size of the memory-mapped region.
   - clocks: phandles to the clocks feeding the mixer
@@ -245,6 +255,7 @@ Required properties:
     * allwinner,sun6i-a31s-display-engine
     * allwinner,sun7i-a20-display-engine
     * allwinner,sun8i-a33-display-engine
+    * allwinner,sun8i-a83t-display-engine
     * allwinner,sun8i-v3s-display-engine
 
   - allwinner,pipelines: list of phandle to the display engine