Merge branch 'master' into test

* master: (688 commits)
  dt-bindings: mailbox: qcom: Document the APCS clock binding
  mailbox: qcom: Create APCS child device for clock controller
  mailbox: qcom: Convert APCS IPC driver to use regmap
  KVM/SVM: Allow direct access to MSR_IA32_SPEC_CTRL
  KVM/VMX: Allow direct access to MSR_IA32_SPEC_CTRL
  KVM/VMX: Emulate MSR_IA32_ARCH_CAPABILITIES
  KVM/x86: Add IBPB support
  KVM/x86: Update the reverse_cpuid list to include CPUID_7_EDX
  pinctrl: remove include file from <linux/device.h>
  firmware: dmi: handle missing DMI data gracefully
  firmware: dmi_scan: Fix handling of empty DMI strings
  firmware: dmi_scan: Drop dmi_initialized
  firmware: dmi: Optimize dmi_matches
  Revert "defer call to mem_cgroup_sk_alloc()"
  soreuseport: fix mem leak in reuseport_add_sock()
  net: qlge: use memmove instead of skb_copy_to_linear_data
  net: qed: use correct strncpy() size
  net: cxgb4: avoid memcpy beyond end of source buffer
  cls_u32: add missing RCU annotation.
  r8152: set rx mode early when linking on
  ...

1 files changed, 78 insertions, 0 deletions

diff --git a/Documentation/devicetree/bindings/eeprom/at24.txt b/Documentation/devicetree/bindings/eeprom/at24.txt
new file mode 100644
index 000000000000..1812c848e369
--- /dev/null
+++ b/Documentation/devicetree/bindings/eeprom/at24.txt
@@ -0,0 +1,78 @@
+EEPROMs (I2C)
+
+Required properties:
+
+  - compatible: Must be a "<manufacturer>,<model>" pair. The following <model>
+                values are supported (assuming "atmel" as manufacturer):
+
+                "atmel,24c00",
+                "atmel,24c01",
+                "atmel,24cs01",
+                "atmel,24c02",
+                "atmel,24cs02",
+                "atmel,24mac402",
+                "atmel,24mac602",
+                "atmel,spd",
+                "atmel,24c04",
+                "atmel,24cs04",
+                "atmel,24c08",
+                "atmel,24cs08",
+                "atmel,24c16",
+                "atmel,24cs16",
+                "atmel,24c32",
+                "atmel,24cs32",
+                "atmel,24c64",
+                "atmel,24cs64",
+                "atmel,24c128",
+                "atmel,24c256",
+                "atmel,24c512",
+                "atmel,24c1024",
+
+                If <manufacturer> is not "atmel", then a fallback must be used
+                with the same <model> and "atmel" as manufacturer.
+
+                Example:
+                        compatible = "microchip,24c128", "atmel,24c128";
+
+                Supported manufacturers are:
+
+                "catalyst",
+                "microchip",
+                "ramtron",
+                "renesas",
+                "nxp",
+                "st",
+
+                Some vendors use different model names for chips which are just
+                variants of the above. Known such exceptions are listed below:
+
+                "renesas,r1ex24002" - the fallback is "atmel,24c02"
+
+  - reg: The I2C address of the EEPROM.
+
+Optional properties:
+
+  - pagesize: The length of the pagesize for writing. Please consult the
+              manual of your device, that value varies a lot. A wrong value
+              may result in data loss! If not specified, a safety value of
+              '1' is used which will be very slow.
+
+  - read-only: This parameterless property disables writes to the eeprom.
+
+  - size: Total eeprom size in bytes.
+
+  - no-read-rollover: This parameterless property indicates that the
+                      multi-address eeprom does not automatically roll over
+                      reads to the next slave address. Please consult the
+                      manual of your device.
+
+  - wp-gpios: GPIO to which the write-protect pin of the chip is connected.
+
+Example:
+
+eeprom@52 {
+	compatible = "atmel,24c32";
+	reg = <0x52>;
+	pagesize = <32>;
+	wp-gpios = <&gpio1 3 0>;
+};