Merge branch 'irq-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip

Pull irq core updates from Thomas Gleixner:
 "A rather large update for the interrupt core code and the irq chip drivers:

   - Add a new bitmap matrix allocator and supporting changes, which is
     used to replace the x86 vector allocator which comes with separate
     pull request. This allows to replace the convoluted nested loop
     allocation function in x86 with a facility which supports the
     recently added property of managed interrupts proper and allows to
     switch to a best effort vector reservation scheme, which addresses
     problems with vector exhaustion.

   - A large update to the ARM GIC-V3-ITS driver adding support for
     range selectors.

   - New interrupt controllers:
       - Meson and Meson8 GPIO
       - BCM7271 L2
       - Socionext EXIU

     If you expected that this will stop at some point, I have to
     disappoint you. There are new ones posted already. Sigh!

   - STM32 interrupt controller support for new platforms.

   - A pile of fixes, cleanups and updates to the MIPS GIC driver

   - The usual small fixes, cleanups and updates all over the place.
     Most visible one is to move the irq chip drivers Kconfig switches
     into a separate Kconfig menu"

* 'irq-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (70 commits)
  genirq: Fix type of shifting literal 1 in __setup_irq()
  irqdomain: Drop pointless NULL check in virq_debug_show_one
  genirq/proc: Return proper error code when irq_set_affinity() fails
  irq/work: Use llist_for_each_entry_safe
  irqchip: mips-gic: Print warning if inherited GIC base is used
  irqchip/mips-gic: Add pr_fmt and reword pr_* messages
  irqchip/stm32: Move the wakeup on interrupt mask
  irqchip/stm32: Fix initial values
  irqchip/stm32: Add stm32h7 support
  dt-bindings/interrupt-controllers: Add compatible string for stm32h7
  irqchip/stm32: Add multi-bank management
  irqchip/stm32: Select GENERIC_IRQ_CHIP
  irqchip/exiu: Add support for Socionext Synquacer EXIU controller
  dt-bindings: Add description of Socionext EXIU interrupt controller
  irqchip/gic-v3-its: Fix VPE activate callback return value
  irqchip: mips-gic: Make IPI bitmaps static
  irqchip: mips-gic: Share register writes in gic_set_type()
  irqchip: mips-gic: Remove gic_vpes variable
  irqchip: mips-gic: Use num_possible_cpus() to reserve IPIs
  irqchip: mips-gic: Configure EIC when CPUs come online
  ...

1 files changed, 36 insertions, 0 deletions

diff --git a/Documentation/devicetree/bindings/interrupt-controller/amlogic,meson-gpio-intc.txt b/Documentation/devicetree/bindings/interrupt-controller/amlogic,meson-gpio-intc.txt
new file mode 100644
index 000000000000..a83f9a5734ca
--- /dev/null
+++ b/Documentation/devicetree/bindings/interrupt-controller/amlogic,meson-gpio-intc.txt
@@ -0,0 +1,36 @@
+Amlogic meson GPIO interrupt controller
+
+Meson SoCs contains an interrupt controller which is able to watch the SoC
+pads and generate an interrupt on edge or level. The controller is essentially
+a 256 pads to 8 GIC interrupt multiplexer, with a filter block to select edge
+or level and polarity. It does not expose all 256 mux inputs because the
+documentation shows that the upper part is not mapped to any pad. The actual
+number of interrupt exposed depends on the SoC.
+
+Required properties:
+
+- compatible : must have "amlogic,meson8-gpio-intc” and either
+   “amlogic,meson8-gpio-intc” for meson8 SoCs (S802) or
+   “amlogic,meson8b-gpio-intc” for meson8b SoCs (S805) or
+   “amlogic,meson-gxbb-gpio-intc” for GXBB SoCs (S905) or
+   “amlogic,meson-gxl-gpio-intc” for GXL SoCs (S905X, S912)
+- interrupt-parent : a phandle to the GIC the interrupts are routed to.
+   Usually this is provided at the root level of the device tree as it is
+   common to most of the SoC.
+- reg : Specifies base physical address and size of the registers.
+- interrupt-controller : Identifies the node as an interrupt controller.
+- #interrupt-cells : Specifies the number of cells needed to encode an
+   interrupt source. The value must be 2.
+- meson,channel-interrupts: Array with the 8 upstream hwirq numbers. These
+   are the hwirqs used on the parent interrupt controller.
+
+Example:
+
+gpio_interrupt: interrupt-controller@9880 {
+	compatible = "amlogic,meson-gxbb-gpio-intc",
+		     "amlogic,meson-gpio-intc";
+	reg = <0x0 0x9880 0x0 0x10>;
+	interrupt-controller;
+	#interrupt-cells = <2>;
+	meson,channel-interrupts = <64 65 66 67 68 69 70 71>;
+};