dt-bindings: media: st,stmipid02: Convert the text bindings to YAML

Convert the text STMIPID02 DT bindings to YAML DT format to permit
validation of DTs using this I2C CSI-2 to CPI bridge.

Reviewed-by: Benjamin Mugnier <benjamin.mugnier@foss.st.com>
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20220929145416.16336-1-marex@denx.de
Signed-off-by: Rob Herring <robh@kernel.org>

1 files changed, 0 insertions, 82 deletions

diff --git a/Documentation/devicetree/bindings/media/i2c/st,st-mipid02.txt b/Documentation/devicetree/bindings/media/i2c/st,st-mipid02.txt
deleted file mode 100644
index 7976e6c40a80..000000000000
--- a/Documentation/devicetree/bindings/media/i2c/st,st-mipid02.txt
+++ /dev/null
@@ -1,82 +0,0 @@
-STMicroelectronics MIPID02 CSI-2 to PARALLEL bridge
-
-MIPID02 has two CSI-2 input ports, only one of those ports can be active at a
-time. Active port input stream will be de-serialized and its content outputted
-through PARALLEL output port.
-CSI-2 first input port is a dual lane 800Mbps per lane whereas CSI-2 second
-input port is a single lane 800Mbps. Both ports support clock and data lane
-polarity swap. First port also supports data lane swap.
-PARALLEL output port has a maximum width of 12 bits.
-Supported formats are RAW6, RAW7, RAW8, RAW10, RAW12, RGB565, RGB888, RGB444,
-YUV420 8-bit, YUV422 8-bit and YUV420 10-bit.
-
-Required Properties:
-- compatible: shall be "st,st-mipid02"
-- clocks: reference to the xclk input clock.
-- clock-names: shall be "xclk".
-- VDDE-supply: sensor digital IO supply. Must be 1.8 volts.
-- VDDIN-supply: sensor internal regulator supply. Must be 1.8 volts.
-
-Optional Properties:
-- reset-gpios: reference to the GPIO connected to the xsdn pin, if any.
-	       This is an active low signal to the mipid02.
-
-Required subnodes:
-  - ports: A ports node with one port child node per device input and output
-	   port, in accordance with the video interface bindings defined in
-	   Documentation/devicetree/bindings/media/video-interfaces.txt. The
-	   port nodes are numbered as follows:
-
-	   Port Description
-	   -----------------------------
-	   0    CSI-2 first input port
-	   1    CSI-2 second input port
-	   2    PARALLEL output
-
-Endpoint node required property for CSI-2 connection is:
-- data-lanes: shall be <1> for Port 1. for Port 0 dual-lane operation shall be
-<1 2> or <2 1>. For Port 0 single-lane operation shall be <1> or <2>.
-Endpoint node optional property for CSI-2 connection is:
-- lane-polarities: any lane can be inverted or not.
-
-Endpoint node required property for PARALLEL connection is:
-- bus-width: shall be set to <6>, <7>, <8>, <10> or <12>.
-Endpoint node optional properties for PARALLEL connection are:
-- hsync-active: active state of the HSYNC signal, 0/1 for LOW/HIGH respectively.
-LOW being the default.
-- vsync-active: active state of the VSYNC signal, 0/1 for LOW/HIGH respectively.
-LOW being the default.
-
-Example:
-
-mipid02: csi2rx@14 {
-	compatible = "st,st-mipid02";
-	reg = <0x14>;
-	status = "okay";
-	clocks = <&clk_ext_camera_12>;
-	clock-names = "xclk";
-	VDDE-supply = <&vdd>;
-	VDDIN-supply = <&vdd>;
-	ports {
-		#address-cells = <1>;
-		#size-cells = <0>;
-		port@0 {
-			reg = <0>;
-
-			ep0: endpoint {
-				data-lanes = <1 2>;
-				remote-endpoint = <&mipi_csi2_in>;
-			};
-		};
-		port@2 {
-			reg = <2>;
-
-			ep2: endpoint {
-				bus-width = <8>;
-				hsync-active = <0>;
-				vsync-active = <0>;
-				remote-endpoint = <&parallel_out>;
-			};
-		};
-	};
-};