Merge tag 'dt-5.16' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc

Pull ARM SoC DT updates from Arnd Bergmann:
 "This is a rather large update for the ARM devicetree files, after a
  few quieter releases, with 775 total commits and 47 branches pulled
  into this one.

  There are 5 new SoC types plus some minor variations, and a total of
  60 new machines, so I'm limiting the summary to the main noteworthy
  items:

   - Apple M1 gain support for PCI and pinctrl, getting a bit closer to
     a usable system out of the box.

   - Qualcomm gains support for Snapdragon 690 (aka SM6350) as well as
     SM7225, 11 new smartphones, and three additional Chromebooks, and
     improvements all over the place.

   - Samsung gains support for ExynosAutov9, an automotive version of
     their smartphone SoC, but otherwise no major changes.

   - Microchip adds the SAMA5D29 SoC in the SAMA5 family, and a number
     of improvements for the recently added SAMA7 family. The LAN966 SoC
     that was added in the platform code does not have dts files yet.
     Two board files are added for the older at91sam9g20 SoC

   - Aspeed supports two additional server boards using their AST2600 as
     BMC, and improves support for qemu models

   - Rockchip RK3566/RK3688 gets added, along with six new development
     boards using RK3328/RK3399/RK3566, and one Chromebook tablet.

   - Two NAS boxes are added using the ARMv4 based Gemini platform

   - One new board is added to the Intel Arria SoC FPGA family

   - Marvell adds one network switch based on Armada 381 and the new
     MOCHAbin 7040 development board

   - NXP adds support for the S32G2 automotive SoC, two imx6 based ebook
     readers, and three additional development boards, which is notably
     less than their usual additions, but they also gain improvements to
     their many existing boards

   - STmicroelectronics adds their stm32mp13 SoC family along with a
     reference board

   - Renesas adds new versions of their R-Car Gen3 SoCs and many updates
     for their older generations

   - Broadcom adds support for a number of Cisco Meraki wireless
     controllers, along with two new boards and other updates for
     BCM53xx/BCM47xx networking SoCs and the Raspberry Pi boards

   - Mediatek improves support for the MT81xx SoCs used in Chromebooks
     as well as the MT76xx networking SoCs

   - NVIDIA adds a number of cleanups and additional support for more
     hardware on the already supported machines

   - TI K3 adds support for three new boards along with cleanups

   - Toshiba adds one board for the Visconti family

   - Xilinx adds five new ZynqMP based machines

   - Amlogic support is added for the Radxa Zero and two Jethub home
     automation controllers, along with changes to other machines

   - Rob Herring continues his work on fixing dtc warnings all over the
     tree.

   - Minor updates for TI OMAP, Mstar, Allwinner/sunxi, Hisilicon,
     Ux500, Unisoc"

* tag 'dt-5.16' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (720 commits)
  arm64: dts: apple: j274: Expose PCI node for the Ethernet MAC address
  arm64: dts: apple: t8103: Add root port interrupt routing
  arm64: dts: apple: t8103: Add PCIe DARTs
  arm64: apple: Add PCIe node
  arm64: apple: Add pinctrl nodes
  ARM: dts: arm: Update ICST clock nodes 'reg' and node names
  ARM: dts: arm: Update register-bit-led nodes 'reg' and node names
  arm64: dts: exynos: add chipid node for exynosautov9 SoC
  ARM: dts: qcom: fix typo in IPQ8064 thermal-sensor node
  Revert "arm64: dts: qcom: msm8916-asus-z00l: Add sensors"
  arm64: dts: qcom: ipq6018: Remove unused 'iface_clk' property from dma-controller node
  arm64: dts: qcom: ipq6018: Remove unused 'qcom,config-pipe-trust-reg' property
  arm64: dts: qcom: sm8350: Add CPU topology and idle-states
  arm64: dts: qcom: Drop unneeded extra device-specific includes
  arm64: dts: qcom: msm8916: Drop standalone smem node
  arm64: dts: qcom: Fix node name of rpm-msg-ram device nodes
  arm64: dts: qcom: msm8916-asus-z00l: Add sensors
  arm64: dts: qcom: msm8916-asus-z00l: Add SDCard
  arm64: dts: qcom: msm8916-asus-z00l: Add touchscreen
  arm64: dts: qcom: sdm845-oneplus: remove devinfo-size from ramoops node
  ...

3 files changed, 417 insertions, 157 deletions

diff --git a/Documentation/devicetree/bindings/memory-controllers/omap-gpmc.txt b/Documentation/devicetree/bindings/memory-controllers/omap-gpmc.txt
deleted file mode 100644
index c1359f4d48d7..000000000000
--- a/Documentation/devicetree/bindings/memory-controllers/omap-gpmc.txt
+++ /dev/null
@@ -1,157 +0,0 @@
-Device tree bindings for OMAP general purpose memory controllers (GPMC)
-
-The actual devices are instantiated from the child nodes of a GPMC node.
-
-Required properties:
-
- - compatible:		Should be set to one of the following:
-
-			ti,omap2420-gpmc (omap2420)
-			ti,omap2430-gpmc (omap2430)
-			ti,omap3430-gpmc (omap3430 & omap3630)
-			ti,omap4430-gpmc (omap4430 & omap4460 & omap543x)
-			ti,am3352-gpmc   (am335x devices)
-
- - reg:			A resource specifier for the register space
-			(see the example below)
- - ti,hwmods:		Should be set to "ti,gpmc" until the DT transition is
-			completed.
- - #address-cells:	Must be set to 2 to allow memory address translation
- - #size-cells:		Must be set to 1 to allow CS address passing
- - gpmc,num-cs:		The maximum number of chip-select lines that controller
-			can support.
- - gpmc,num-waitpins:	The maximum number of wait pins that controller can
-			support.
- - ranges:		Must be set up to reflect the memory layout with four
-			integer values for each chip-select line in use:
-
-			   <cs-number> 0 <physical address of mapping> <size>
-
-			Currently, calculated values derived from the contents
-			of the per-CS register GPMC_CONFIG7 (as set up by the
-			bootloader) are used for the physical address decoding.
-			As this will change in the future, filling correct
-			values here is a requirement.
- - interrupt-controller: The GPMC driver implements and interrupt controller for
-			the NAND events "fifoevent" and "termcount" plus the
-			rising/falling edges on the GPMC_WAIT pins.
-			The interrupt number mapping is as follows
-			0 - NAND_fifoevent
-			1 - NAND_termcount
-			2 - GPMC_WAIT0 pin edge
-			3 - GPMC_WAIT1 pin edge, and so on.
- - interrupt-cells:	Must be set to 2
- - gpio-controller:	The GPMC driver implements a GPIO controller for the
-			GPMC WAIT pins that can be used as general purpose inputs.
-			0 maps to GPMC_WAIT0 pin.
- - gpio-cells:		Must be set to 2
-
-Required properties when using NAND prefetch dma:
- - dmas			GPMC NAND prefetch dma channel
- - dma-names		Must be set to "rxtx"
-
-Timing properties for child nodes. All are optional and default to 0.
-
- - gpmc,sync-clk-ps:	Minimum clock period for synchronous mode, in picoseconds
-
- Chip-select signal timings (in nanoseconds) corresponding to GPMC_CONFIG2:
- - gpmc,cs-on-ns:	Assertion time
- - gpmc,cs-rd-off-ns:	Read deassertion time
- - gpmc,cs-wr-off-ns:	Write deassertion time
-
- ADV signal timings (in nanoseconds) corresponding to GPMC_CONFIG3:
- - gpmc,adv-on-ns:	Assertion time
- - gpmc,adv-rd-off-ns:	Read deassertion time
- - gpmc,adv-wr-off-ns:	Write deassertion time
- - gpmc,adv-aad-mux-on-ns:	Assertion time for AAD
- - gpmc,adv-aad-mux-rd-off-ns:	Read deassertion time for AAD
- - gpmc,adv-aad-mux-wr-off-ns:	Write deassertion time for AAD
-
- WE signals timings (in nanoseconds) corresponding to GPMC_CONFIG4:
- - gpmc,we-on-ns	Assertion time
- - gpmc,we-off-ns:	Deassertion time
-
- OE signals timings (in nanoseconds) corresponding to GPMC_CONFIG4:
- - gpmc,oe-on-ns:	Assertion time
- - gpmc,oe-off-ns:	Deassertion time
- - gpmc,oe-aad-mux-on-ns:	Assertion time for AAD
- - gpmc,oe-aad-mux-off-ns:	Deassertion time for AAD
-
- Access time and cycle time timings (in nanoseconds) corresponding to
- GPMC_CONFIG5:
- - gpmc,page-burst-access-ns: 	Multiple access word delay
- - gpmc,access-ns:		Start-cycle to first data valid delay
- - gpmc,rd-cycle-ns:		Total read cycle time
- - gpmc,wr-cycle-ns:		Total write cycle time
- - gpmc,bus-turnaround-ns:	Turn-around time between successive accesses
- - gpmc,cycle2cycle-delay-ns:	Delay between chip-select pulses
- - gpmc,clk-activation-ns: 	GPMC clock activation time
- - gpmc,wait-monitoring-ns:	Start of wait monitoring with regard to valid
-				data
-
-Boolean timing parameters. If property is present parameter enabled and
-disabled if omitted:
- - gpmc,adv-extra-delay:	ADV signal is delayed by half GPMC clock
- - gpmc,cs-extra-delay:		CS signal is delayed by half GPMC clock
- - gpmc,cycle2cycle-diffcsen:	Add "cycle2cycle-delay" between successive
-				accesses to a different CS
- - gpmc,cycle2cycle-samecsen:	Add "cycle2cycle-delay" between successive
-				accesses to the same CS
- - gpmc,oe-extra-delay:		OE signal is delayed by half GPMC clock
- - gpmc,we-extra-delay:		WE signal is delayed by half GPMC clock
- - gpmc,time-para-granularity:	Multiply all access times by 2
-
-The following are only applicable to OMAP3+ and AM335x:
- - gpmc,wr-access-ns:		In synchronous write mode, for single or
-				burst accesses, defines the number of
-				GPMC_FCLK cycles from start access time
-				to the GPMC_CLK rising edge used by the
-				memory device for the first data capture.
- - gpmc,wr-data-mux-bus-ns:	In address-data multiplex mode, specifies
-				the time when the first data is driven on
-				the address-data bus.
-
-GPMC chip-select settings properties for child nodes. All are optional.
-
-- gpmc,burst-length	Page/burst length. Must be 4, 8 or 16.
-- gpmc,burst-wrap	Enables wrap bursting
-- gpmc,burst-read	Enables read page/burst mode
-- gpmc,burst-write	Enables write page/burst mode
-- gpmc,device-width	Total width of device(s) connected to a GPMC
-			chip-select in bytes. The GPMC supports 8-bit
-			and 16-bit devices and so this property must be
-			1 or 2.
-- gpmc,mux-add-data	Address and data multiplexing configuration.
-			Valid values are 1 for address-address-data
-			multiplexing mode and 2 for address-data
-			multiplexing mode.
-- gpmc,sync-read	Enables synchronous read. Defaults to asynchronous
-			is this is not set.
-- gpmc,sync-write	Enables synchronous writes. Defaults to asynchronous
-			is this is not set.
-- gpmc,wait-pin		Wait-pin used by client. Must be less than
-			"gpmc,num-waitpins".
-- gpmc,wait-on-read	Enables wait monitoring on reads.
-- gpmc,wait-on-write	Enables wait monitoring on writes.
-
-Example for an AM33xx board:
-
-	gpmc: gpmc@50000000 {
-		compatible = "ti,am3352-gpmc";
-		ti,hwmods = "gpmc";
-		reg = <0x50000000 0x2000>;
-		interrupts = <100>;
-		dmas = <&edma 52 0>;
-		dma-names = "rxtx";
-		gpmc,num-cs = <8>;
-		gpmc,num-waitpins = <2>;
-		#address-cells = <2>;
-		#size-cells = <1>;
-		ranges = <0 0 0x08000000 0x10000000>; /* CS0 @addr 0x8000000, size 0x10000000 */
-		interrupt-controller;
-		#interrupt-cells = <2>;
-		gpio-controller;
-		#gpio-cells = <2>;
-
-		/* child nodes go here */
-	};
diff --git a/Documentation/devicetree/bindings/memory-controllers/ti,gpmc-child.yaml b/Documentation/devicetree/bindings/memory-controllers/ti,gpmc-child.yaml
new file mode 100644
index 000000000000..6e3995bb1630
--- /dev/null
+++ b/Documentation/devicetree/bindings/memory-controllers/ti,gpmc-child.yaml
@@ -0,0 +1,245 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/memory-controllers/ti,gpmc-child.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: device tree bindings for children of the Texas Instruments GPMC
+
+maintainers:
+  - Tony Lindgren <tony@atomide.com>
+  - Roger Quadros <rogerq@kernel.org>
+
+description:
+  This binding is meant for the child nodes of the GPMC node. The node
+  represents any device connected to the GPMC bus. It may be a Flash chip,
+  RAM chip or Ethernet controller, etc. These properties are meant for
+  configuring the GPMC settings/timings and will accompany the bindings
+  supported by the respective device.
+
+properties:
+  reg: true
+
+# GPMC Timing properties for child nodes. All are optional and default to 0.
+  gpmc,sync-clk-ps:
+    description: Minimum clock period for synchronous mode
+    default: 0
+
+# Chip-select signal timings corresponding to GPMC_CONFIG2:
+  gpmc,cs-on-ns:
+    description: Assertion time
+    default: 0
+
+  gpmc,cs-rd-off-ns:
+    description: Read deassertion time
+    default: 0
+
+  gpmc,cs-wr-off-ns:
+    description: Write deassertion time
+    default: 0
+
+# ADV signal timings corresponding to GPMC_CONFIG3:
+  gpmc,adv-on-ns:
+    description: Assertion time
+    default: 0
+
+  gpmc,adv-rd-off-ns:
+    description: Read deassertion time
+    default: 0
+
+  gpmc,adv-wr-off-ns:
+    description: Write deassertion time
+    default: 0
+
+  gpmc,adv-aad-mux-on-ns:
+    description: Assertion time for AAD
+    default: 0
+
+  gpmc,adv-aad-mux-rd-off-ns:
+    description: Read deassertion time for AAD
+    default: 0
+
+  gpmc,adv-aad-mux-wr-off-ns:
+    description: Write deassertion time for AAD
+    default: 0
+
+# WE signals timings corresponding to GPMC_CONFIG4:
+  gpmc,we-on-ns:
+    description: Assertion time
+    default: 0
+
+  gpmc,we-off-ns:
+    description: Deassertion time
+    default: 0
+
+# OE signals timings corresponding to GPMC_CONFIG4:
+  gpmc,oe-on-ns:
+    description: Assertion time
+    default: 0
+
+  gpmc,oe-off-ns:
+    description: Deassertion time
+    default: 0
+
+  gpmc,oe-aad-mux-on-ns:
+    description: Assertion time for AAD
+    default: 0
+
+  gpmc,oe-aad-mux-off-ns:
+    description: Deassertion time for AAD
+    default: 0
+
+# Access time and cycle time timings (in nanoseconds) corresponding to
+# GPMC_CONFIG5:
+  gpmc,page-burst-access-ns:
+    description: Multiple access word delay
+    default: 0
+
+  gpmc,access-ns:
+    description: Start-cycle to first data valid delay
+    default: 0
+
+  gpmc,rd-cycle-ns:
+    description: Total read cycle time
+    default: 0
+
+  gpmc,wr-cycle-ns:
+    description: Total write cycle time
+    default: 0
+
+  gpmc,bus-turnaround-ns:
+    description: Turn-around time between successive accesses
+    default: 0
+
+  gpmc,cycle2cycle-delay-ns:
+    description: Delay between chip-select pulses
+    default: 0
+
+  gpmc,clk-activation-ns:
+    description: GPMC clock activation time
+    default: 0
+
+  gpmc,wait-monitoring-ns:
+    description: Start of wait monitoring with regard to valid data
+    default: 0
+
+# Boolean timing parameters. If property is present, parameter is enabled
+# otherwise disabled.
+  gpmc,adv-extra-delay:
+    description: ADV signal is delayed by half GPMC clock
+    type: boolean
+
+  gpmc,cs-extra-delay:
+    description: CS signal is delayed by half GPMC clock
+    type: boolean
+
+  gpmc,cycle2cycle-diffcsen:
+    description: |
+      Add "cycle2cycle-delay" between successive accesses
+      to a different CS
+    type: boolean
+
+  gpmc,cycle2cycle-samecsen:
+    description: |
+      Add "cycle2cycle-delay" between successive accesses
+      to the same CS
+    type: boolean
+
+  gpmc,oe-extra-delay:
+    description: OE signal is delayed by half GPMC clock
+    type: boolean
+
+  gpmc,we-extra-delay:
+    description: WE signal is delayed by half GPMC clock
+    type: boolean
+
+  gpmc,time-para-granularity:
+    description: Multiply all access times by 2
+    type: boolean
+
+# The following two properties are applicable only to OMAP3+ and AM335x:
+  gpmc,wr-access-ns:
+    description: |
+      In synchronous write mode, for single or
+      burst accesses, defines the number of
+      GPMC_FCLK cycles from start access time
+      to the GPMC_CLK rising edge used by the
+      memory device for the first data capture.
+    default: 0
+
+  gpmc,wr-data-mux-bus-ns:
+    description: |
+      In address-data multiplex mode, specifies
+      the time when the first data is driven on
+      the address-data bus.
+    default: 0
+
+# GPMC chip-select settings properties for child nodes. All are optional.
+  gpmc,burst-length:
+    description: Page/burst length.
+    $ref: /schemas/types.yaml#/definitions/uint32
+    enum: [0, 4, 8, 16]
+    default: 0
+
+  gpmc,burst-wrap:
+    description: Enables wrap bursting
+    type: boolean
+
+  gpmc,burst-read:
+    description: Enables read page/burst mode
+    type: boolean
+
+  gpmc,burst-write:
+    description: Enables write page/burst mode
+    type: boolean
+
+  gpmc,device-width:
+    description: |
+      Total width of device(s) connected to a GPMC
+      chip-select in bytes. The GPMC supports 8-bit
+      and 16-bit devices and so this property must be
+      1 or 2.
+    $ref: /schemas/types.yaml#/definitions/uint32
+    enum: [1, 2]
+    default: 1
+
+  gpmc,mux-add-data:
+    description: |
+      Address and data multiplexing configuration.
+      Valid values are
+      0 for Non multiplexed mode
+      1 for address-address-data multiplexing mode and
+      2 for address-data multiplexing mode.
+    $ref: /schemas/types.yaml#/definitions/uint32
+    enum: [0, 1, 2]
+
+  gpmc,sync-read:
+    description: |
+      Enables synchronous read. Defaults to asynchronous
+      is this is not set.
+    type: boolean
+
+  gpmc,sync-write:
+    description: |
+      Enables synchronous writes. Defaults to asynchronous
+      is this is not set.
+    type: boolean
+
+  gpmc,wait-pin:
+    description: |
+      Wait-pin used by client. Must be less than "gpmc,num-waitpins".
+    $ref: /schemas/types.yaml#/definitions/uint32
+
+  gpmc,wait-on-read:
+    description: Enables wait monitoring on reads.
+    type: boolean
+
+  gpmc,wait-on-write:
+    description: Enables wait monitoring on writes.
+    type: boolean
+
+required:
+  - reg
+
+# the GPMC child will have its own native properties
+additionalProperties: true
diff --git a/Documentation/devicetree/bindings/memory-controllers/ti,gpmc.yaml b/Documentation/devicetree/bindings/memory-controllers/ti,gpmc.yaml
new file mode 100644
index 000000000000..25b42d68f9b3
--- /dev/null
+++ b/Documentation/devicetree/bindings/memory-controllers/ti,gpmc.yaml
@@ -0,0 +1,172 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/memory-controllers/ti,gpmc.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Texas Instruments GPMC Memory Controller device-tree bindings
+
+maintainers:
+  - Tony Lindgren <tony@atomide.com>
+  - Roger Quadros <rogerq@kernel.org>
+
+description:
+  The GPMC is a unified memory controller dedicated for interfacing
+  with external memory devices like
+  - Asynchronous SRAM-like memories and ASICs
+  - Asynchronous, synchronous, and page mode burst NOR flash
+  - NAND flash
+  - Pseudo-SRAM devices
+
+properties:
+  compatible:
+    items:
+      - enum:
+          - ti,am3352-gpmc
+          - ti,omap2420-gpmc
+          - ti,omap2430-gpmc
+          - ti,omap3430-gpmc
+          - ti,omap4430-gpmc
+
+  reg:
+    maxItems: 1
+
+  interrupts:
+    maxItems: 1
+
+  clocks:
+    maxItems: 1
+    description: |
+      Functional clock. Used for bus timing calculations and
+      GPMC configuration.
+
+  clock-names:
+    items:
+      - const: fck
+
+  dmas:
+    items:
+      - description: DMA channel for GPMC NAND prefetch
+
+  dma-names:
+    items:
+      - const: rxtx
+
+  "#address-cells": true
+
+  "#size-cells": true
+
+  gpmc,num-cs:
+    description: maximum number of supported chip-select lines.
+    $ref: /schemas/types.yaml#/definitions/uint32
+
+  gpmc,num-waitpins:
+    description: maximum number of supported wait pins.
+    $ref: /schemas/types.yaml#/definitions/uint32
+
+  ranges:
+    minItems: 1
+    description: |
+      Must be set up to reflect the memory layout with four
+      integer values for each chip-select line in use,
+      <cs-number> 0 <physical address of mapping> <size>
+    items:
+      - description: NAND bank 0
+      - description: NOR/SRAM bank 0
+      - description: NOR/SRAM bank 1
+
+  '#interrupt-cells':
+    const: 2
+
+  interrupt-controller:
+    description: |
+      The GPMC driver implements and interrupt controller for
+      the NAND events "fifoevent" and "termcount" plus the
+      rising/falling edges on the GPMC_WAIT pins.
+      The interrupt number mapping is as follows
+      0 - NAND_fifoevent
+      1 - NAND_termcount
+      2 - GPMC_WAIT0 pin edge
+      3 - GPMC_WAIT1 pin edge, and so on.
+
+  '#gpio-cells':
+    const: 2
+
+  gpio-controller:
+    description: |
+      The GPMC driver implements a GPIO controller for the
+      GPMC WAIT pins that can be used as general purpose inputs.
+      0 maps to GPMC_WAIT0 pin.
+
+  ti,hwmods:
+    description:
+      Name of the HWMOD associated with GPMC. This is for legacy
+      omap2/3 platforms only.
+    $ref: /schemas/types.yaml#/definitions/string
+    deprecated: true
+
+  ti,no-idle-on-init:
+    description:
+      Prevent idling the module at init. This is for legacy omap2/3
+      platforms only.
+    type: boolean
+    deprecated: true
+
+patternProperties:
+  "@[0-7],[a-f0-9]+$":
+    type: object
+    description: |
+      The child device node represents the device connected to the GPMC
+      bus. The device can be a NAND chip, SRAM device, NOR device
+      or an ASIC.
+
+    allOf:
+      - $ref: "ti,gpmc-child.yaml"
+
+    unevaluatedProperties: false
+
+required:
+  - compatible
+  - reg
+  - gpmc,num-cs
+  - gpmc,num-waitpins
+  - "#address-cells"
+  - "#size-cells"
+
+additionalProperties: false
+
+examples:
+  - |
+    #include <dt-bindings/interrupt-controller/arm-gic.h>
+    #include <dt-bindings/gpio/gpio.h>
+
+    gpmc: memory-controller@50000000 {
+      compatible = "ti,am3352-gpmc";
+      reg = <0x50000000 0x2000>;
+      interrupts = <100>;
+      clocks = <&l3s_clkctrl>;
+      clock-names = "fck";
+      dmas = <&edma 52 0>;
+      dma-names = "rxtx";
+      gpmc,num-cs = <8>;
+      gpmc,num-waitpins = <2>;
+      #address-cells = <2>;
+      #size-cells = <1>;
+      ranges = <0 0 0x08000000 0x10000000>; /* CS0 @addr 0x8000000, size 0x10000000 */
+      interrupt-controller;
+      #interrupt-cells = <2>;
+      gpio-controller;
+      #gpio-cells = <2>;
+
+      nand@0,0 {
+        compatible = "ti,omap2-nand";
+        reg = <0 0 4>;
+        interrupt-parent = <&gpmc>;
+        interrupts = <0 IRQ_TYPE_NONE>, /* fifoevent */
+                     <1 IRQ_TYPE_NONE>; /* termcount */
+        ti,nand-xfer-type = "prefetch-dma";
+        ti,nand-ecc-opt = "bch16";
+        ti,elm-id = <&elm>;
+        rb-gpios = <&gpmc 0 GPIO_ACTIVE_HIGH>; /* gpmc_wait0 pin */
+      };
+    };