Merge tag 'renesas-soc-for-v4.17' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/horms/renesas into next/soc

Pull "Renesas ARM Based SoC Updates for v4.17" from Simon Horman:

01d675f159e0 ARM: shmobile: rcar-gen2: Add watchdog support
58adf1ba0d22 ARM: shmobile: Add watchdog support

* SoC
  - Identify R-Car V3H (r8a77980) and M3N (r8a77965)

  - Enable R-Car Gen2 regulator quirk for Stout board with H3 (r8a7790) SoC

    Marek Vaust says "Regulator setup is suboptimal on H2 Stout too. The
    Stout newly has two DA9210 regulators, so the quirk is extended to
    handle another DA9210 at i2c address 0x70."

  - Add watchdog support

    This is the SoC portion of the following solution. It is not yet
    enabled in DT as it is not functional without clock dependencies
    in place.

    Fabrizio Castro says "this series has been around for some time as RFC,
    and it has collected useful comments from the community along the way.
    The solution proposed by this patch set works for most R-Car Gen2 and
    RZ/G1 devices, but not all of them. We now know that for some R-Car
    Gen2 early revisions there is no proper software fix. Anyway, no
    product has been built around early revisions, but development boards
    mounting early revisions (basically prototypes) are still out there.
    As a result, this series isn't enabling the internal watchdog on R-Car
    Gen2 boards, developers may enable it in board specific device trees if
    needed.  This series has been tested by me on the iwg20d, iwg22d,
    Lager, Alt, and Koelsch boards.

   The problem
   ===========
   To deal with SMP on R-Car Gen2 and RZ/G1, we install a reset vector to
   ICRAM1 and we program the [S]BAR registers so that when we turn ON the
   non-boot CPUs they are redirected to the reset vector installed by Linux
   in ICRAM1, and eventually they continue the execution to RAM, where the
   SMP bring-up code will take care of the rest.  The content of the [S]BAR
   registers survives a watchdog triggered reset, and as such after the
   watchdog fires the boot core will try and execute the SMP bring-up code
   instead of jumping to the bootrom code.

   The fix
   =======
   The main strategy for the solution is to let the reset vector decide if
   it needs to jump to shmobile_boot_fn or to the bootrom code.  In a
   watchdog triggered reset scenario, since the [S]BAR registers keep their
   values, the boot CPU will jump into the newly designed reset vector, the
   assembly routine will eventually test WOVF (a bit in register RWTCSRA
   that indicates if the watchdog counter has overflown, the value of this
   bit gets retained in this scenario), and jump to the bootrom code which
   will in turn load up the bootloader, etc.  When bringing up SMP or using
   CPU hotplug, the reset vector will jump to shmobile_boot_fn instead."

* R-Car Rst
  - Add support for R-Car V3H (r8a77980) and V3H (r8a77980)

* R-Car SYSC
  - Mark rcar_sysc_matches[] __initconst

   Geert Uytterhoeven says "This frees another 1764 bytes
   (arm32/shmobile_defconfig) or 1000 bytes (arm64/renesas_defconfig) of
   memory after kernel init."

  - Fix power area parents

    Sergei Shtylyov says "According to the figure 9.2(b) of the R-Car
    Series, 3rd Generation User’s Manual: Hardware Rev. 0.80 the A2IRn and
    A2SCn power areas in R8A77970 have the A3IR area as a parent, thus the
    SYSC driver has those parents wrong.."

  - Add support for R-Car V3H (r8a77980) and V3H (r8a77980)

* tag 'renesas-soc-for-v4.17' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
  ARM: shmobile: rcar-gen2: Add watchdog support
  ARM: shmobile: Add watchdog support
  ARM: shmobile: rcar-gen2: Fix error check in regulator quirk
  soc: renesas: rcar-rst: Add support for R-Car M3-N
  ARM: shmobile: stout: enable R-Car Gen2 regulator quirk
  soc: renesas: rcar-sysc: Add R-Car M3-N support
  soc: renesas: Identify R-Car M3-N
  soc: renesas: rcar-sysc: add R8A77980 support
  dt-bindings: power: add R8A77980 SYSC power domain definitions
  soc: renesas: r8a77970-sysc: fix power area parents
  soc: renesas: rcar-rst: Enable watchdog as reset trigger for Gen2
  soc: renesas: rcar-rst: add R8A77980 support
  soc: renesas: identify R-Car V3H
  soc: renesas: rcar-sysc: Mark rcar_sysc_matches[] __initconst

1 files changed, 2 insertions, 0 deletions

diff --git a/Documentation/devicetree/bindings/power/renesas,rcar-sysc.txt b/Documentation/devicetree/bindings/power/renesas,rcar-sysc.txt
index 8690f10426a3..ab399e559257 100644
--- a/Documentation/devicetree/bindings/power/renesas,rcar-sysc.txt
+++ b/Documentation/devicetree/bindings/power/renesas,rcar-sysc.txt
@@ -17,7 +17,9 @@ Required properties:
       - "renesas,r8a7794-sysc" (R-Car E2)
       - "renesas,r8a7795-sysc" (R-Car H3)
       - "renesas,r8a7796-sysc" (R-Car M3-W)
+      - "renesas,r8a77965-sysc" (R-Car M3-N)
       - "renesas,r8a77970-sysc" (R-Car V3M)
+      - "renesas,r8a77980-sysc" (R-Car V3H)
       - "renesas,r8a77995-sysc" (R-Car D3)
   - reg: Address start and address range for the device.
   - #power-domain-cells: Must be 1.