Merge tag 'usb-for-v4.15' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-next

Felipe writes:

usb: changes for v4.15 merge window

Not much going on this time around. With only 51 non-merge commits,
this was one of the smallest pull requests from the Gadget tree.

Most of the changes are in the mtu3 driver which added support for
36-bit DMA, support for USB 3.1 and support for dual-role (along with
some non-critical fixes).

The dwc2 driver got a few improvements to how we handle gadget state
tracking and also added support for STM32F7xx devices.

Other than that, we just some minor non-critical fixes and
improvements all over the place.

4 files changed, 20 insertions, 10 deletions

diff --git a/Documentation/devicetree/bindings/usb/dwc2.txt b/Documentation/devicetree/bindings/usb/dwc2.txt
index fcf199b64d3d..e64d903bcbe8 100644
--- a/Documentation/devicetree/bindings/usb/dwc2.txt
+++ b/Documentation/devicetree/bindings/usb/dwc2.txt
@@ -19,6 +19,8 @@ Required properties:
   configured in FS mode;
   - "st,stm32f4x9-hsotg": The DWC2 USB HS controller instance in STM32F4x9 SoCs
   configured in HS mode;
+  - "st,stm32f7xx-hsotg": The DWC2 USB HS controller instance in STM32F7xx SoCs
+    configured in HS mode;
 - reg : Should contain 1 register range (address and length)
 - interrupts : Should contain 1 interrupt
 - clocks: clock provider specifier
diff --git a/Documentation/devicetree/bindings/usb/mediatek,mtu3.txt b/Documentation/devicetree/bindings/usb/mediatek,mtu3.txt
index 49f54767cd21..b2271d8e6b50 100644
--- a/Documentation/devicetree/bindings/usb/mediatek,mtu3.txt
+++ b/Documentation/devicetree/bindings/usb/mediatek,mtu3.txt
@@ -14,9 +14,9 @@ Required properties:
  - vusb33-supply : regulator of USB avdd3.3v
  - clocks : a list of phandle + clock-specifier pairs, one for each
 	entry in clock-names
- - clock-names : must contain "sys_ck" and "ref_ck" for clock of controller;
-	"wakeup_deb_p0" and "wakeup_deb_p1" are optional, they are
-	depends on "mediatek,enable-wakeup"
+ - clock-names : must contain "sys_ck" for clock of controller,
+	the following clocks are optional:
+	"ref_ck", "mcu_ck" and "dam_ck";
  - phys : a list of phandle + phy specifier pairs
  - dr_mode : should be one of "host", "peripheral" or "otg",
 	refer to usb/generic.txt
@@ -30,9 +30,10 @@ Optional properties:
 	when supports dual-role mode.
  - vbus-supply : reference to the VBUS regulator, needed when supports
 	dual-role mode.
- - pinctl-names : a pinctrl state named "default" must be defined,
-	"id_float" and "id_ground" are optinal which depends on
-	"mediatek,enable-manual-drd"
+ - pinctrl-names : a pinctrl state named "default" is optional, and need be
+	defined if auto drd switch is enabled, that means the property dr_mode
+	is set as "otg", and meanwhile the property "mediatek,enable-manual-drd"
+	is not set.
  - pinctrl-0 : pin control group
 	See: Documentation/devicetree/bindings/pinctrl/pinctrl-bindings.txt
 
@@ -44,6 +45,8 @@ Optional properties:
  - mediatek,enable-wakeup : supports ip sleep wakeup used by host mode
  - mediatek,syscon-wakeup : phandle to syscon used to access USB wakeup
 	control register, it depends on "mediatek,enable-wakeup".
+ - mediatek,u3p-dis-msk : mask to disable u3ports, bit0 for u3port0,
+	bit1 for u3port1, ... etc;
 
 Sub-nodes:
 The xhci should be added as subnode to mtu3 as shown in the following example
@@ -63,9 +66,7 @@ ssusb: usb@11271000 {
 	clocks = <&topckgen CLK_TOP_USB30_SEL>, <&clk26m>,
 		 <&pericfg CLK_PERI_USB0>,
 		 <&pericfg CLK_PERI_USB1>;
-	clock-names = "sys_ck", "ref_ck",
-		      "wakeup_deb_p0",
-		      "wakeup_deb_p1";
+	clock-names = "sys_ck", "ref_ck";
 	vusb33-supply = <&mt6397_vusb_reg>;
 	vbus-supply = <&usb_p0_vbus>;
 	extcon = <&extcon_usb>;
diff --git a/Documentation/devicetree/bindings/usb/renesas_usb3.txt b/Documentation/devicetree/bindings/usb/renesas_usb3.txt
index e28025883b79..87a45e2f9b7f 100644
--- a/Documentation/devicetree/bindings/usb/renesas_usb3.txt
+++ b/Documentation/devicetree/bindings/usb/renesas_usb3.txt
@@ -15,6 +15,10 @@ Required properties:
   - interrupts: Interrupt specifier for the USB3.0 Peripheral
   - clocks: clock phandle and specifier pair
 
+Optional properties:
+  - phys: phandle + phy specifier pair
+  - phy-names: must be "usb"
+
 Example of R-Car H3 ES1.x:
 	usb3_peri0: usb@ee020000 {
 		compatible = "renesas,r8a7795-usb3-peri",
diff --git a/Documentation/devicetree/bindings/usb/renesas_usbhs.txt b/Documentation/devicetree/bindings/usb/renesas_usbhs.txt
index 9e18e000339e..47394ab788e3 100644
--- a/Documentation/devicetree/bindings/usb/renesas_usbhs.txt
+++ b/Documentation/devicetree/bindings/usb/renesas_usbhs.txt
@@ -3,6 +3,8 @@ Renesas Electronics USBHS driver
 Required properties:
   - compatible: Must contain one or more of the following:
 
+	- "renesas,usbhs-r8a7743" for r8a7743 (RZ/G1M) compatible device
+	- "renesas,usbhs-r8a7745" for r8a7745 (RZ/G1E) compatible device
 	- "renesas,usbhs-r8a7790" for r8a7790 (R-Car H2) compatible device
 	- "renesas,usbhs-r8a7791" for r8a7791 (R-Car M2-W) compatible device
 	- "renesas,usbhs-r8a7792" for r8a7792 (R-Car V2H) compatible device
@@ -10,7 +12,8 @@ Required properties:
 	- "renesas,usbhs-r8a7794" for r8a7794 (R-Car E2) compatible device
 	- "renesas,usbhs-r8a7795" for r8a7795 (R-Car H3) compatible device
 	- "renesas,usbhs-r8a7796" for r8a7796 (R-Car M3-W) compatible device
-	- "renesas,rcar-gen2-usbhs" for R-Car Gen2 compatible device
+	- "renesas,usbhs-r8a77995" for r8a77995 (R-Car D3) compatible device
+	- "renesas,rcar-gen2-usbhs" for R-Car Gen2 or RZ/G1 compatible devices
 	- "renesas,rcar-gen3-usbhs" for R-Car Gen3 compatible device
 
 	When compatible with the generic version, nodes must list the