diff options
| author | Linus Torvalds <torvalds@linux-foundation.org> | 2023-05-02 15:40:41 -0700 |
|---|---|---|
| committer | Linus Torvalds <torvalds@linux-foundation.org> | 2023-05-02 15:40:41 -0700 |
| commit | 348551ddaf311c76b01cdcbaf61b6fef06a49144 (patch) | |
| tree | 65f217523ea41fac639a6a51ac56865dadbdd26d /Documentation/devicetree/bindings | |
| parent | 7df047b3f0aa0c0ba730b6be9ab35c0053a3d4fd (diff) | |
| parent | b7badd752de05312fdb1aeb388480f706d0c087f (diff) | |
Merge tag 'pinctrl-v6.4-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pin control updates from Linus Walleij:
"Mostly drivers! Nothing special: some new Qualcomm chips as usual, and
the new NXP S32 and nVidia BlueField-3.
Core changes:
- Make a lot of pin controllers with GPIO and irqchips immutable,
i.e. not living structs, but const structs. This is driving a
changed initiated by the irqchip maintainers.
New drivers:
- New driver for the NXP S32 SoC pin controller
- As part of a thorough cleanup and restructuring of the
Ralink/Mediatek drivers, the Ralink MIPS pin control drivers were
folded into the Mediatek directory and the family is renamed
"mtmips". The Ralink chips live on as Mediatek MIPS family where
new variants can be added. As part of this work also the device
tree bindings were reworked.
- New subdriver for the Qualcomm SM7150 SoC.
- New subdriver for the Qualcomm IPQ9574 SoC.
- New driver for the nVidia BlueField-3 SoC.
- Support for the Qualcomm PMM8654AU mixed signal circuit GPIO.
- Support for the Qualcomm PMI632 mixed signal circuit GPIO.
Improvements:
- Add some missing pins and generic cleanups on the Renesas r8a779g0
and r8a779g0 pin controllers. Generic Renesas extension for power
source selection on several SoCs.
- Misc cleanups for the Atmel AT91 and AT91-PIO4 pin controllers
- Make the GPIO mode work on the Qualcomm SM8550-lpass-lpi driver.
- Several device tree binding cleanups as the binding YAML syntax is
solidifying"
* tag 'pinctrl-v6.4-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (153 commits)
pinctrl-bcm2835.c: fix race condition when setting gpio dir
dt-bindings: pinctrl: qcom,sm8150: Drop duplicate function value "atest_usb2"
dt-bindings: pinctrl: qcom: Add few missing functions
pinctrl: qcom: spmi-gpio: Add PMI632 support
dt-bindings: pinctrl: qcom,pmic-gpio: add PMI632
pinctrl: wpcm450: select MFD_SYSCON
pinctrl: qcom ssbi-gpio: Convert to immutable irq_chip
pinctrl: qcom ssbi-mpp: Convert to immutable irq_chip
pinctrl: qcom spmi-mpp: Convert to immutable irq_chip
pinctrl: plgpio: Convert to immutable irq_chip
pinctrl: pistachio: Convert to immutable irq_chip
pinctrl: pic32: Convert to immutable irq_chip
pinctrl: sx150x: Convert to immutable irq_chip
pinctrl: stmfx: Convert to immutable irq_chip
pinctrl: st: Convert to immutable irq_chip
pinctrl: mcp23s08: Convert to immutable irq_chip
pinctrl: equilibrium: Convert to immutable irq_chip
pinctrl: npcm7xx: Convert to immutable irq_chip
pinctrl: armada-37xx: Convert to immutable irq_chip
pinctrl: nsp: Convert to immutable irq_chip
...
Diffstat (limited to 'Documentation/devicetree/bindings')
119 files changed, 2093 insertions, 1300 deletions
diff --git a/Documentation/devicetree/bindings/gpio/nxp,pcf8575.yaml b/Documentation/devicetree/bindings/gpio/nxp,pcf8575.yaml index f0ff66c4c74e..3718103e966a 100644 --- a/Documentation/devicetree/bindings/gpio/nxp,pcf8575.yaml +++ b/Documentation/devicetree/bindings/gpio/nxp,pcf8575.yaml @@ -39,6 +39,10 @@ properties: reg: maxItems: 1 + gpio-line-names: + minItems: 1 + maxItems: 16 + gpio-controller: true '#gpio-cells': diff --git a/Documentation/devicetree/bindings/pinctrl/actions,s500-pinctrl.yaml b/Documentation/devicetree/bindings/pinctrl/actions,s500-pinctrl.yaml index fb0f69ce9c16..7cb8a747feee 100644 --- a/Documentation/devicetree/bindings/pinctrl/actions,s500-pinctrl.yaml +++ b/Documentation/devicetree/bindings/pinctrl/actions,s500-pinctrl.yaml @@ -185,7 +185,7 @@ patternProperties: additionalProperties: false allOf: - - $ref: "pinctrl.yaml#" + - $ref: pinctrl.yaml# required: - compatible diff --git a/Documentation/devicetree/bindings/pinctrl/allwinner,sun4i-a10-pinctrl.yaml b/Documentation/devicetree/bindings/pinctrl/allwinner,sun4i-a10-pinctrl.yaml index 1e3c8de6cae1..467016cbb037 100644 --- a/Documentation/devicetree/bindings/pinctrl/allwinner,sun4i-a10-pinctrl.yaml +++ b/Documentation/devicetree/bindings/pinctrl/allwinner,sun4i-a10-pinctrl.yaml @@ -142,7 +142,7 @@ allOf: # boards are defining it at the moment so it would generate a lot of # warnings. - - $ref: "pinctrl.yaml#" + - $ref: pinctrl.yaml# - if: not: properties: diff --git a/Documentation/devicetree/bindings/pinctrl/amlogic,meson-pinctrl-a1.yaml b/Documentation/devicetree/bindings/pinctrl/amlogic,meson-pinctrl-a1.yaml new file mode 100644 index 000000000000..99080c9eaac3 --- /dev/null +++ b/Documentation/devicetree/bindings/pinctrl/amlogic,meson-pinctrl-a1.yaml @@ -0,0 +1,67 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/pinctrl/amlogic,meson-pinctrl-a1.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Amlogic Meson A1 pinmux controller + +maintainers: + - Neil Armstrong <neil.armstrong@linaro.org> + +allOf: + - $ref: amlogic,meson-pinctrl-common.yaml# + +properties: + compatible: + enum: + - amlogic,meson-a1-periphs-pinctrl + - amlogic,meson-s4-periphs-pinctrl + +required: + - compatible + +patternProperties: + "^bank@[0-9a-z]+$": + $ref: amlogic,meson-pinctrl-common.yaml#/$defs/meson-gpio + + unevaluatedProperties: false + + properties: + reg: + maxItems: 2 + + reg-names: + items: + - const: mux + - const: gpio + +unevaluatedProperties: + type: object + $ref: amlogic,meson-pinctrl-common.yaml#/$defs/meson-pins + +examples: + - | + periphs_pinctrl: pinctrl { + compatible = "amlogic,meson-a1-periphs-pinctrl"; + #address-cells = <1>; + #size-cells = <1>; + ranges; + + bank@400 { + reg = <0x0400 0x003c>, + <0x0480 0x0118>; + reg-names = "mux", "gpio"; + gpio-controller; + #gpio-cells = <2>; + gpio-ranges = <&periphs_pinctrl 0 0 62>; + }; + + cec_ao_a_h_pins: cec_ao_a_h { + mux { + groups = "cec_ao_a_h"; + function = "cec_ao_a_h"; + bias-disable; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/pinctrl/amlogic,meson-pinctrl-common.yaml b/Documentation/devicetree/bindings/pinctrl/amlogic,meson-pinctrl-common.yaml new file mode 100644 index 000000000000..a7b29ef0bab6 --- /dev/null +++ b/Documentation/devicetree/bindings/pinctrl/amlogic,meson-pinctrl-common.yaml @@ -0,0 +1,57 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/pinctrl/amlogic,meson-pinctrl-common.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Amlogic Meson pinmux controller + +maintainers: + - Neil Armstrong <neil.armstrong@linaro.org> + +allOf: + - $ref: pinctrl.yaml# + +properties: + ranges: true + + "#address-cells": + enum: [1, 2] + + "#size-cells": + enum: [1, 2] + +required: + - ranges + - "#address-cells" + - "#size-cells" + +additionalProperties: true + +$defs: + meson-gpio: + type: object + + properties: + gpio-controller: true + + "#gpio-cells": + const: 2 + + gpio-ranges: + maxItems: 1 + + required: + - reg + - reg-names + - gpio-controller + - "#gpio-cells" + - gpio-ranges + + meson-pins: + type: object + additionalProperties: + type: object + allOf: + - $ref: pincfg-node.yaml# + - $ref: pinmux-node.yaml# diff --git a/Documentation/devicetree/bindings/pinctrl/amlogic,meson-pinctrl-g12a-aobus.yaml b/Documentation/devicetree/bindings/pinctrl/amlogic,meson-pinctrl-g12a-aobus.yaml new file mode 100644 index 000000000000..7c9c94ec5b7b --- /dev/null +++ b/Documentation/devicetree/bindings/pinctrl/amlogic,meson-pinctrl-g12a-aobus.yaml @@ -0,0 +1,68 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/pinctrl/amlogic,meson-pinctrl-g12a-aobus.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Amlogic Meson G12 AOBUS pinmux controller + +maintainers: + - Neil Armstrong <neil.armstrong@linaro.org> + +allOf: + - $ref: amlogic,meson-pinctrl-common.yaml# + +properties: + compatible: + enum: + - amlogic,meson-g12a-aobus-pinctrl + +required: + - compatible + +patternProperties: + "^bank@[0-9a-z]+$": + $ref: amlogic,meson-pinctrl-common.yaml#/$defs/meson-gpio + + unevaluatedProperties: false + + properties: + reg: + maxItems: 3 + + reg-names: + items: + - const: mux + - const: ds + - const: gpio + +unevaluatedProperties: + type: object + $ref: amlogic,meson-pinctrl-common.yaml#/$defs/meson-pins + +examples: + - | + ao_pinctrl: pinctrl { + compatible = "amlogic,meson-g12a-aobus-pinctrl"; + #address-cells = <1>; + #size-cells = <1>; + ranges; + + bank@14 { + reg = <0x14 0x8>, + <0x1c 0x8>, + <0x24 0x14>; + reg-names = "mux", "ds", "gpio"; + gpio-controller; + #gpio-cells = <2>; + gpio-ranges = <&ao_pinctrl 0 0 15>; + }; + + cec_ao_a_h_pins: cec_ao_a_h { + mux { + groups = "cec_ao_a_h"; + function = "cec_ao_a_h"; + bias-disable; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/pinctrl/amlogic,meson-pinctrl-g12a-periphs.yaml b/Documentation/devicetree/bindings/pinctrl/amlogic,meson-pinctrl-g12a-periphs.yaml new file mode 100644 index 000000000000..4bcb8b60420f --- /dev/null +++ b/Documentation/devicetree/bindings/pinctrl/amlogic,meson-pinctrl-g12a-periphs.yaml @@ -0,0 +1,72 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/pinctrl/amlogic,meson-pinctrl-g12a-periphs.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Amlogic Meson G12 PERIPHS pinmux controller + +maintainers: + - Neil Armstrong <neil.armstrong@linaro.org> + +allOf: + - $ref: amlogic,meson-pinctrl-common.yaml# + +properties: + compatible: + enum: + - amlogic,meson-g12a-periphs-pinctrl + +required: + - compatible + +patternProperties: + "^bank@[0-9a-z]+$": + $ref: amlogic,meson-pinctrl-common.yaml#/$defs/meson-gpio + + unevaluatedProperties: false + + properties: + reg: + maxItems: 5 + + reg-names: + items: + - const: gpio + - const: pull + - const: pull-enable + - const: mux + - const: ds + +unevaluatedProperties: + type: object + $ref: amlogic,meson-pinctrl-common.yaml#/$defs/meson-pins + +examples: + - | + periphs_pinctrl: pinctrl { + compatible = "amlogic,meson-g12a-periphs-pinctrl"; + #address-cells = <1>; + #size-cells = <1>; + ranges; + + bank@40 { + reg = <0x40 0x4c>, + <0xe8 0x18>, + <0x120 0x18>, + <0x2c0 0x40>, + <0x340 0x1c>; + reg-names = "gpio", "pull", "pull-enable", "mux", "ds"; + gpio-controller; + #gpio-cells = <2>; + gpio-ranges = <&periphs_pinctrl 0 0 86>; + }; + + cec_ao_a_h_pins: cec_ao_a_h { + mux { + groups = "cec_ao_a_h"; + function = "cec_ao_a_h"; + bias-disable; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/pinctrl/amlogic,meson8-pinctrl-aobus.yaml b/Documentation/devicetree/bindings/pinctrl/amlogic,meson8-pinctrl-aobus.yaml new file mode 100644 index 000000000000..32d99c9b6afc --- /dev/null +++ b/Documentation/devicetree/bindings/pinctrl/amlogic,meson8-pinctrl-aobus.yaml @@ -0,0 +1,76 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/pinctrl/amlogic,meson8-pinctrl-aobus.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Amlogic Meson8 AOBUS pinmux controller + +maintainers: + - Neil Armstrong <neil.armstrong@linaro.org> + +allOf: + - $ref: amlogic,meson-pinctrl-common.yaml# + +properties: + compatible: + oneOf: + - enum: + - amlogic,meson8-aobus-pinctrl + - amlogic,meson8b-aobus-pinctrl + - amlogic,meson-gxbb-aobus-pinctrl + - amlogic,meson-gxl-aobus-pinctrl + - amlogic,meson-axg-aobus-pinctrl + - items: + - const: amlogic,meson8m2-aobus-pinctrl + - const: amlogic,meson8-aobus-pinctrl + +required: + - compatible + +patternProperties: + "^bank@[0-9a-z]+$": + $ref: amlogic,meson-pinctrl-common.yaml#/$defs/meson-gpio + + unevaluatedProperties: false + + properties: + reg: + maxItems: 3 + + reg-names: + items: + - const: mux + - const: pull + - const: gpio + +unevaluatedProperties: + type: object + $ref: amlogic,meson-pinctrl-common.yaml#/$defs/meson-pins + +examples: + - | + pinctrl_aobus: pinctrl { + compatible = "amlogic,meson8-aobus-pinctrl"; + #address-cells = <1>; + #size-cells = <1>; + ranges; + + bank@14 { + reg = <0x14 0x4>, + <0x2c 0x4>, + <0x24 0x8>; + reg-names = "mux", "pull", "gpio"; + gpio-controller; + #gpio-cells = <2>; + gpio-ranges = <&pinctrl_aobus 0 0 16>; + }; + + cec_ao_a_h_pins: cec_ao_a_h { + mux { + groups = "cec_ao_a_h"; + function = "cec_ao_a_h"; + bias-disable; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/pinctrl/amlogic,meson8-pinctrl-cbus.yaml b/Documentation/devicetree/bindings/pinctrl/amlogic,meson8-pinctrl-cbus.yaml new file mode 100644 index 000000000000..d0441051f34a --- /dev/null +++ b/Documentation/devicetree/bindings/pinctrl/amlogic,meson8-pinctrl-cbus.yaml @@ -0,0 +1,78 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/pinctrl/amlogic,meson8-pinctrl-cbus.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Amlogic Meson8 CBUS pinmux controller + +maintainers: + - Neil Armstrong <neil.armstrong@linaro.org> + +allOf: + - $ref: amlogic,meson-pinctrl-common.yaml# + +properties: + compatible: + oneOf: + - enum: + - amlogic,meson8-cbus-pinctrl + - amlogic,meson8b-cbus-pinctrl + - amlogic,meson-gxbb-periphs-pinctrl + - amlogic,meson-gxl-periphs-pinctrl + - amlogic,meson-axg-periphs-pinctrl + - items: + - const: amlogic,meson8m2-cbus-pinctrl + - const: amlogic,meson8-cbus-pinctrl + +required: + - compatible + +patternProperties: + "^bank@[0-9a-z]+$": + $ref: amlogic,meson-pinctrl-common.yaml#/$defs/meson-gpio + + unevaluatedProperties: false + + properties: + reg: + maxItems: 4 + + reg-names: + items: + - const: mux + - const: pull + - const: pull-enable + - const: gpio + +unevaluatedProperties: + type: object + $ref: amlogic,meson-pinctrl-common.yaml#/$defs/meson-pins + +examples: + - | + pinctrl_cbus: pinctrl { + compatible = "amlogic,meson8-cbus-pinctrl"; + #address-cells = <1>; + #size-cells = <1>; + ranges; + + bank@80b0 { + reg = <0x80b0 0x28>, + <0x80e8 0x18>, + <0x8120 0x18>, + <0x8030 0x30>; + reg-names = "mux", "pull", "pull-enable", "gpio"; + gpio-controller; + #gpio-cells = <2>; + gpio-ranges = <&pinctrl_cbus 0 0 120>; + }; + + cec_ao_a_h_pins: cec_ao_a_h { + mux { + groups = "cec_ao_a_h"; + function = "cec_ao_a_h"; + bias-disable; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/pinctrl/apple,pinctrl.yaml b/Documentation/devicetree/bindings/pinctrl/apple,pinctrl.yaml index 684c03a6bd40..9c07935919ea 100644 --- a/Documentation/devicetree/bindings/pinctrl/apple,pinctrl.yaml +++ b/Documentation/devicetree/bindings/pinctrl/apple,pinctrl.yaml @@ -74,7 +74,7 @@ patternProperties: additionalProperties: false allOf: - - $ref: "pinctrl.yaml#" + - $ref: pinctrl.yaml# required: - compatible diff --git a/Documentation/devicetree/bindings/pinctrl/aspeed,ast2400-pinctrl.yaml b/Documentation/devicetree/bindings/pinctrl/aspeed,ast2400-pinctrl.yaml index f4f1ee6b116e..bef85c25cdef 100644 --- a/Documentation/devicetree/bindings/pinctrl/aspeed,ast2400-pinctrl.yaml +++ b/Documentation/devicetree/bindings/pinctrl/aspeed,ast2400-pinctrl.yaml @@ -32,7 +32,7 @@ patternProperties: then: patternProperties: "^function|groups$": - $ref: "/schemas/types.yaml#/definitions/string" + $ref: /schemas/types.yaml#/definitions/string enum: [ ACPI, ADC0, ADC1, ADC10, ADC11, ADC12, ADC13, ADC14, ADC15, ADC2, ADC3, ADC4, ADC5, ADC6, ADC7, ADC8, ADC9, BMCINT, DDCCLK, DDCDAT, EXTRST, FLACK, FLBUSY, FLWP, GPID, GPID0, GPID2, GPID4, GPID6, GPIE0, @@ -51,7 +51,7 @@ patternProperties: VGAHS, VGAVS, VPI18, VPI24, VPI30, VPO12, VPO24, WDTRST1, WDTRST2] allOf: - - $ref: "pinctrl.yaml#" + - $ref: pinctrl.yaml# required: - compatible diff --git a/Documentation/devicetree/bindings/pinctrl/aspeed,ast2500-pinctrl.yaml b/Documentation/devicetree/bindings/pinctrl/aspeed,ast2500-pinctrl.yaml index 8168f0088471..14c391f16899 100644 --- a/Documentation/devicetree/bindings/pinctrl/aspeed,ast2500-pinctrl.yaml +++ b/Documentation/devicetree/bindings/pinctrl/aspeed,ast2500-pinctrl.yaml @@ -44,7 +44,7 @@ patternProperties: then: patternProperties: "^function|groups$": - $ref: "/schemas/types.yaml#/definitions/string" + $ref: /schemas/types.yaml#/definitions/string enum: [ ACPI, ADC0, ADC1, ADC10, ADC11, ADC12, ADC13, ADC14, ADC15, ADC2, ADC3, ADC4, ADC5, ADC6, ADC7, ADC8, ADC9, BMCINT, DDCCLK, DDCDAT, ESPI, FWSPICS1, FWSPICS2, GPID0, GPID2, GPID4, GPID6, GPIE0, GPIE2, @@ -65,7 +65,7 @@ patternProperties: VGAVS, VPI24, VPO, WDTRST1, WDTRST2] allOf: - - $ref: "pinctrl.yaml#" + - $ref: pinctrl.yaml# required: - compatible diff --git a/Documentation/devicetree/bindings/pinctrl/aspeed,ast2600-pinctrl.yaml b/Documentation/devicetree/bindings/pinctrl/aspeed,ast2600-pinctrl.yaml index 62424c42c981..859a1889dc1e 100644 --- a/Documentation/devicetree/bindings/pinctrl/aspeed,ast2600-pinctrl.yaml +++ b/Documentation/devicetree/bindings/pinctrl/aspeed,ast2600-pinctrl.yaml @@ -30,7 +30,7 @@ patternProperties: then: properties: function: - $ref: "/schemas/types.yaml#/definitions/string" + $ref: /schemas/types.yaml#/definitions/string enum: [ ADC0, ADC1, ADC10, ADC11, ADC12, ADC13, ADC14, ADC15, ADC2, ADC3, ADC4, ADC5, ADC6, ADC7, ADC8, ADC9, BMCINT, EMMC, ESPI, ESPIALT, FSI1, FSI2, FWQSPI, FWSPIABR, FWSPID, FWSPIWP, GPIT0, GPIT1, GPIT2, GPIT3, @@ -55,7 +55,7 @@ patternProperties: USB2BD, USB2BH, VB, VGAHS, VGAVS, WDTRST1, WDTRST2, WDTRST3, WDTRST4 ] groups: - $ref: "/schemas/types.yaml#/definitions/string" + $ref: /schemas/types.yaml#/definitions/string enum: [ ADC0, ADC1, ADC10, ADC11, ADC12, ADC13, ADC14, ADC15, ADC2, ADC3, ADC4, ADC5, ADC6, ADC7, ADC8, ADC9, BMCINT, EMMCG1, EMMCG4, EMMCG8, ESPI, ESPIALT, FSI1, FSI2, FWQSPI, FWSPIABR, FWSPID, FWSPIWP, @@ -84,7 +84,7 @@ patternProperties: WDTRST3, WDTRST4] allOf: - - $ref: "pinctrl.yaml#" + - $ref: pinctrl.yaml# required: - compatible diff --git a/Documentation/devicetree/bindings/pinctrl/brcm,bcm6318-pinctrl.yaml b/Documentation/devicetree/bindings/pinctrl/brcm,bcm6318-pinctrl.yaml index ab019a1998e8..4478a76171f7 100644 --- a/Documentation/devicetree/bindings/pinctrl/brcm,bcm6318-pinctrl.yaml +++ b/Documentation/devicetree/bindings/pinctrl/brcm,bcm6318-pinctrl.yaml @@ -38,7 +38,7 @@ patternProperties: gpio8, gpio9, gpio10, gpio11, gpio12, gpio13, gpio40 ] allOf: - - $ref: "pinctrl.yaml#" + - $ref: pinctrl.yaml# required: - compatible diff --git a/Documentation/devicetree/bindings/pinctrl/brcm,bcm63268-pinctrl.yaml b/Documentation/devicetree/bindings/pinctrl/brcm,bcm63268-pinctrl.yaml index 8c9d4668c8c4..73e1caa7c011 100644 --- a/Documentation/devicetree/bindings/pinctrl/brcm,bcm63268-pinctrl.yaml +++ b/Documentation/devicetree/bindings/pinctrl/brcm,bcm63268-pinctrl.yaml @@ -42,7 +42,7 @@ patternProperties: vdsl_phy_override_3_grp, dsl_gpio8, dsl_gpio9 ] allOf: - - $ref: "pinctrl.yaml#" + - $ref: pinctrl.yaml# required: - compatible diff --git a/Documentation/devicetree/bindings/pinctrl/brcm,bcm6328-pinctrl.yaml b/Documentation/devicetree/bindings/pinctrl/brcm,bcm6328-pinctrl.yaml index a8e22ec02215..2750ba42aeb8 100644 --- a/Documentation/devicetree/bindings/pinctrl/brcm,bcm6328-pinctrl.yaml +++ b/Documentation/devicetree/bindings/pinctrl/brcm,bcm6328-pinctrl.yaml @@ -37,7 +37,7 @@ patternProperties: usb_port1 ] allOf: - - $ref: "pinctrl.yaml#" + - $ref: pinctrl.yaml# required: - compatible diff --git a/Documentation/devicetree/bindings/pinctrl/brcm,bcm6358-pinctrl.yaml b/Documentation/devicetree/bindings/pinctrl/brcm,bcm6358-pinctrl.yaml index 35867355a47a..2f6c540498bc 100644 --- a/Documentation/devicetree/bindings/pinctrl/brcm,bcm6358-pinctrl.yaml +++ b/Documentation/devicetree/bindings/pinctrl/brcm,bcm6358-pinctrl.yaml @@ -35,7 +35,7 @@ patternProperties: led_grp, spi_cs_grp, utopia_grp, pwm_syn_clk, sys_irq_grp ] allOf: - - $ref: "pinctrl.yaml#" + - $ref: pinctrl.yaml# required: - compatible diff --git a/Documentation/devicetree/bindings/pinctrl/brcm,bcm6362-pinctrl.yaml b/Documentation/devicetree/bindings/pinctrl/brcm,bcm6362-pinctrl.yaml index b584d4b27223..b3044f805753 100644 --- a/Documentation/devicetree/bindings/pinctrl/brcm,bcm6362-pinctrl.yaml +++ b/Documentation/devicetree/bindings/pinctrl/brcm,bcm6362-pinctrl.yaml @@ -42,7 +42,7 @@ patternProperties: gpio22, gpio23, gpio24, gpio25, gpio26, gpio27, nand_grp ] allOf: - - $ref: "pinctrl.yaml#" + - $ref: pinctrl.yaml# required: - compatible diff --git a/Documentation/devicetree/bindings/pinctrl/brcm,bcm6368-pinctrl.yaml b/Documentation/devicetree/bindings/pinctrl/brcm,bcm6368-pinctrl.yaml index 229323d9237d..3236871827df 100644 --- a/Documentation/devicetree/bindings/pinctrl/brcm,bcm6368-pinctrl.yaml +++ b/Documentation/devicetree/bindings/pinctrl/brcm,bcm6368-pinctrl.yaml @@ -43,7 +43,7 @@ patternProperties: gpio31, uart1_grp ] allOf: - - $ref: "pinctrl.yaml#" + - $ref: pinctrl.yaml# required: - compatible diff --git a/Documentation/devicetree/bindings/pinctrl/brcm,ns-pinmux.yaml b/Documentation/devicetree/bindings/pinctrl/brcm,ns-pinmux.yaml index 8d1e5b1cdd5f..0a39dd26ee1a 100644 --- a/Documentation/devicetree/bindings/pinctrl/brcm,ns-pinmux.yaml +++ b/Documentation/devicetree/bindings/pinctrl/brcm,ns-pinmux.yaml @@ -53,7 +53,7 @@ patternProperties: additionalProperties: false allOf: - - $ref: "pinctrl.yaml#" + - $ref: pinctrl.yaml# - if: properties: compatible: diff --git a/Documentation/devicetree/bindings/pinctrl/canaan,k210-fpioa.yaml b/Documentation/devicetree/bindings/pinctrl/canaan,k210-fpioa.yaml index a78cb2796001..7f4f36a58e56 100644 --- a/Documentation/devicetree/bindings/pinctrl/canaan,k210-fpioa.yaml +++ b/Documentation/devicetree/bindings/pinctrl/canaan,k210-fpioa.yaml @@ -144,7 +144,7 @@ patternProperties: additionalProperties: false allOf: - - $ref: "pinctrl.yaml#" + - $ref: pinctrl.yaml# required: - compatible diff --git a/Documentation/devicetree/bindings/pinctrl/cirrus,lochnagar.yaml b/Documentation/devicetree/bindings/pinctrl/cirrus,lochnagar.yaml index 5cd512b7d5ba..5e000b3fadde 100644 --- a/Documentation/devicetree/bindings/pinctrl/cirrus,lochnagar.yaml +++ b/Documentation/devicetree/bindings/pinctrl/cirrus,lochnagar.yaml @@ -173,7 +173,7 @@ properties: additionalProperties: false allOf: - - $ref: "pinctrl.yaml#" + - $ref: pinctrl.yaml# required: - compatible diff --git a/Documentation/devicetree/bindings/pinctrl/cirrus,madera.yaml b/Documentation/devicetree/bindings/pinctrl/cirrus,madera.yaml index 6bd42e43cdab..bb61a30321a1 100644 --- a/Documentation/devicetree/bindings/pinctrl/cirrus,madera.yaml +++ b/Documentation/devicetree/bindings/pinctrl/cirrus,madera.yaml @@ -40,8 +40,8 @@ properties: '-pins$': type: object allOf: - - $ref: "pincfg-node.yaml#" - - $ref: "pinmux-node.yaml#" + - $ref: pincfg-node.yaml# + - $ref: pinmux-node.yaml# properties: groups: description: diff --git a/Documentation/devicetree/bindings/pinctrl/cypress,cy8c95x0.yaml b/Documentation/devicetree/bindings/pinctrl/cypress,cy8c95x0.yaml index 915cbbcc3555..222d57541b65 100644 --- a/Documentation/devicetree/bindings/pinctrl/cypress,cy8c95x0.yaml +++ b/Documentation/devicetree/bindings/pinctrl/cypress,cy8c95x0.yaml @@ -109,7 +109,7 @@ required: additionalProperties: false allOf: - - $ref: "pinctrl.yaml#" + - $ref: pinctrl.yaml# examples: - | diff --git a/Documentation/devicetree/bindings/pinctrl/fsl,imx7d-pinctrl.yaml b/Documentation/devicetree/bindings/pinctrl/fsl,imx7d-pinctrl.yaml index 621038662188..7bd723ab1281 100644 --- a/Documentation/devicetree/bindings/pinctrl/fsl,imx7d-pinctrl.yaml +++ b/Documentation/devicetree/bindings/pinctrl/fsl,imx7d-pinctrl.yaml @@ -68,7 +68,7 @@ patternProperties: additionalProperties: false allOf: - - $ref: "pinctrl.yaml#" + - $ref: pinctrl.yaml# required: - compatible diff --git a/Documentation/devicetree/bindings/pinctrl/fsl,imx8m-pinctrl.yaml b/Documentation/devicetree/bindings/pinctrl/fsl,imx8m-pinctrl.yaml index 7ae084397258..6068be11dfe2 100644 --- a/Documentation/devicetree/bindings/pinctrl/fsl,imx8m-pinctrl.yaml +++ b/Documentation/devicetree/bindings/pinctrl/fsl,imx8m-pinctrl.yaml @@ -65,7 +65,7 @@ patternProperties: additionalProperties: false allOf: - - $ref: "pinctrl.yaml#" + - $ref: pinctrl.yaml# required: - compatible diff --git a/Documentation/devicetree/bindings/pinctrl/fsl,imx8ulp-pinctrl.yaml b/Documentation/devicetree/bindings/pinctrl/fsl,imx8ulp-pinctrl.yaml index 693398d88223..7dcf681271d3 100644 --- a/Documentation/devicetree/bindings/pinctrl/fsl,imx8ulp-pinctrl.yaml +++ b/Documentation/devicetree/bindings/pinctrl/fsl,imx8ulp-pinctrl.yaml @@ -57,7 +57,7 @@ patternProperties: additionalProperties: false allOf: - - $ref: "pinctrl.yaml#" + - $ref: pinctrl.yaml# required: - compatible diff --git a/Documentation/devicetree/bindings/pinctrl/fsl,imx93-pinctrl.yaml b/Documentation/devicetree/bindings/pinctrl/fsl,imx93-pinctrl.yaml index 66baa6082a4f..2f2405102996 100644 --- a/Documentation/devicetree/bindings/pinctrl/fsl,imx93-pinctrl.yaml +++ b/Documentation/devicetree/bindings/pinctrl/fsl,imx93-pinctrl.yaml @@ -14,7 +14,7 @@ description: for common binding part and usage. allOf: - - $ref: "pinctrl.yaml#" + - $ref: pinctrl.yaml# properties: compatible: diff --git a/Documentation/devicetree/bindings/pinctrl/ingenic,pinctrl.yaml b/Documentation/devicetree/bindings/pinctrl/ingenic,pinctrl.yaml index a4397930e0e8..35723966b70a 100644 --- a/Documentation/devicetree/bindings/pinctrl/ingenic,pinctrl.yaml +++ b/Documentation/devicetree/bindings/pinctrl/ingenic,pinctrl.yaml @@ -119,7 +119,7 @@ patternProperties: additionalProperties: false allOf: - - $ref: "pinctrl.yaml#" + - $ref: pinctrl.yaml# required: - compatible diff --git a/Documentation/devicetree/bindings/pinctrl/intel,lgm-io.yaml b/Documentation/devicetree/bindings/pinctrl/intel,lgm-io.yaml index ca0fef6e535e..1144ca2896e3 100644 --- a/Documentation/devicetree/bindings/pinctrl/intel,lgm-io.yaml +++ b/Documentation/devicetree/bindings/pinctrl/intel,lgm-io.yaml @@ -48,7 +48,7 @@ patternProperties: additionalProperties: false allOf: - - $ref: "pinctrl.yaml#" + - $ref: pinctrl.yaml# required: - compatible diff --git a/Documentation/devicetree/bindings/pinctrl/intel,pinctrl-thunderbay.yaml b/Documentation/devicetree/bindings/pinctrl/intel,pinctrl-thunderbay.yaml deleted file mode 100644 index f001add16814..000000000000 --- a/Documentation/devicetree/bindings/pinctrl/intel,pinctrl-thunderbay.yaml +++ /dev/null @@ -1,120 +0,0 @@ -# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause) -%YAML 1.2 ---- -$id: http://devicetree.org/schemas/pinctrl/intel,pinctrl-thunderbay.yaml# -$schema: http://devicetree.org/meta-schemas/core.yaml# - -title: Intel Thunder Bay pin controller - -maintainers: - - Lakshmi Sowjanya D <lakshmi.sowjanya.d@intel.com> - -description: | - Intel Thunder Bay SoC integrates a pin controller which enables control - of pin directions, input/output values and configuration - for a total of 67 pins. - -properties: - compatible: - const: intel,thunderbay-pinctrl - - reg: - maxItems: 1 - - gpio-controller: true - - '#gpio-cells': - const: 2 - - gpio-ranges: - maxItems: 1 - - interrupts: - description: - Specifies the interrupt lines to be used by the controller. - maxItems: 2 - - interrupt-controller: true - - '#interrupt-cells': - const: 2 - -patternProperties: - '^gpio@[0-9a-f]*$': - type: object - additionalProperties: false - - description: - Child nodes can be specified to contain pin configuration information, - which can then be utilized by pinctrl client devices. - The following properties are supported. - - properties: - pins: - description: | - The name(s) of the pins to be configured in the child node. - Supported pin names are "GPIO0" up to "GPIO66". - - bias-disable: true - - bias-pull-down: true - - bias-pull-up: true - - drive-strength: - description: Drive strength for the pad. - enum: [0, 1, 2, 3, 4, 5, 6, 7, 8, 9, 10, 11, 12, 13, 14, 15] - - bias-bus-hold: - type: boolean - - input-schmitt-enable: - type: boolean - - slew-rate: - description: GPIO slew rate control. - 0 - Slow - 1 - Fast - enum: [0, 1] - -additionalProperties: false - -required: - - compatible - - reg - - gpio-controller - - '#gpio-cells' - - gpio-ranges - - interrupts - - interrupt-controller - - '#interrupt-cells' - -examples: - - | - #include <dt-bindings/interrupt-controller/arm-gic.h> - #include <dt-bindings/interrupt-controller/irq.h> - // Example 1 - pinctrl0: gpio@0 { - compatible = "intel,thunderbay-pinctrl"; - reg = <0x600b0000 0x88>; - gpio-controller; - #gpio-cells = <0x2>; - gpio-ranges = <&pinctrl0 0 0 67>; - interrupts = <GIC_SPI 94 IRQ_TYPE_LEVEL_HIGH>, - <GIC_SPI 95 IRQ_TYPE_LEVEL_HIGH>; - interrupt-controller; - #interrupt-cells = <2>; - }; - - // Example 2 - pinctrl1: gpio@1 { - compatible = "intel,thunderbay-pinctrl"; - reg = <0x600c0000 0x88>; - gpio-controller; - #gpio-cells = <0x2>; - gpio-ranges = <&pinctrl1 0 0 53>; - interrupts = <GIC_SPI 94 IRQ_TYPE_LEVEL_HIGH>, - <GIC_SPI 95 IRQ_TYPE_LEVEL_HIGH>; - interrupt-controller; - #interrupt-cells = <2>; - }; diff --git a/Documentation/devicetree/bindings/pinctrl/lantiq,pinctrl-xway.txt b/Documentation/devicetree/bindings/pinctrl/lantiq,pinctrl-xway.txt index 4658f105fa09..6bd9bc61becb 100644 --- a/Documentation/devicetree/bindings/pinctrl/lantiq,pinctrl-xway.txt +++ b/Documentation/devicetree/bindings/pinctrl/lantiq,pinctrl-xway.txt @@ -1,11 +1,7 @@ Lantiq XWAY pinmux controller Required properties: -- compatible: "lantiq,pinctrl-xway", (DEPRECATED: Use "lantiq,pinctrl-danube") - "lantiq,pinctrl-xr9", (DEPRECATED: Use "lantiq,xrx100-pinctrl" or - "lantiq,xrx200-pinctrl") - "lantiq,pinctrl-ase", (DEPRECATED: Use "lantiq,ase-pinctrl") - "lantiq,<chip>-pinctrl", where <chip> is: +- compatible: "lantiq,<chip>-pinctrl", where <chip> is: "ase" (XWAY AMAZON Family) "danube" (XWAY DANUBE Family) "xrx100" (XWAY xRX100 Family) @@ -45,29 +41,6 @@ Required subnode-properties: Valid values for group and function names: -XWAY: (DEPRECATED: Use DANUBE) - mux groups: - exin0, exin1, exin2, jtag, ebu a23, ebu a24, ebu a25, ebu clk, ebu cs1, - ebu wait, nand ale, nand cs1, nand cle, spi, spi_cs1, spi_cs2, spi_cs3, - spi_cs4, spi_cs5, spi_cs6, asc0, asc0 cts rts, stp, nmi, gpt1, gpt2, - gpt3, clkout0, clkout1, clkout2, clkout3, gnt1, gnt2, gnt3, req1, req2, - req3 - - functions: - spi, asc, cgu, jtag, exin, stp, gpt, nmi, pci, ebu - -XR9: ( DEPRECATED: Use xRX100/xRX200) - mux groups: - exin0, exin1, exin2, exin3, exin4, jtag, ebu a23, ebu a24, ebu a25, - ebu clk, ebu cs1, ebu wait, nand ale, nand cs1, nand cle, nand rdy, - nand rd, spi, spi_cs1, spi_cs2, spi_cs3, spi_cs4, spi_cs5, spi_cs6, - asc0, asc0 cts rts, stp, nmi, gpt1, gpt2, gpt3, clkout0, clkout1, - clkout2, clkout3, gnt1, gnt2, gnt3, gnt4, req1, req2, req3, req4, mdio, - gphy0 led0, gphy0 led1, gphy0 led2, gphy1 led0, gphy1 led1, gphy1 led2 - - functions: - spi, asc, cgu, jtag, exin, stp, gpt, nmi, pci, ebu, mdio, gphy - AMAZON: mux groups: exin0, exin1, exin2, jtag, spi_di, spi_do, spi_clk, spi_cs1, spi_cs2, @@ -139,12 +112,6 @@ Optional subnode-properties: 0: none, 1: down, 2: up. - lantiq,open-drain: Boolean, enables open-drain on the defined pin. -Valid values for XWAY pin names: (DEPRECATED: Use DANUBE) - Pinconf pins can be referenced via the names io0-io31. - -Valid values for XR9 pin names: (DEPRECATED: Use xrX100/xRX200) - Pinconf pins can be referenced via the names io0-io55. - Valid values for AMAZON pin names: Pinconf pins can be referenced via the names io0-io31. diff --git a/Documentation/devicetree/bindings/pinctrl/marvell,ac5-pinctrl.yaml b/Documentation/devicetree/bindings/pinctrl/marvell,ac5-pinctrl.yaml index 491f67e7cc4f..afea9424c7e1 100644 --- a/Documentation/devicetree/bindings/pinctrl/marvell,ac5-pinctrl.yaml +++ b/Documentation/devicetree/bindings/pinctrl/marvell,ac5-pinctrl.yaml @@ -28,7 +28,7 @@ patternProperties: properties: marvell,function: - $ref: "/schemas/types.yaml#/definitions/string" + $ref: /schemas/types.yaml#/definitions/string description: Indicates the function to select. enum: [ dev_init_done, ge, gpio, i2c0, i2c1, int_out, led, nand, pcie, ptp, sdio, @@ -47,7 +47,7 @@ patternProperties: mpp40, mpp41, mpp42, mpp43, mpp44, mpp45 ] allOf: - - $ref: "pinctrl.yaml#" + - $ref: pinctrl.yaml# required: - compatible diff --git a/Documentation/devicetree/bindings/pinctrl/mediatek,mt65xx-pinctrl.yaml b/Documentation/devicetree/bindings/pinctrl/mediatek,mt65xx-pinctrl.yaml index a55c8e4ff26e..bccff08a5ba3 100644 --- a/Documentation/devicetree/bindings/pinctrl/mediatek,mt65xx-pinctrl.yaml +++ b/Documentation/devicetree/bindings/pinctrl/mediatek,mt65xx-pinctrl.yaml @@ -4,13 +4,13 @@ $id: http://devicetree.org/schemas/pinctrl/mediatek,mt65xx-pinctrl.yaml# $schema: http://devicetree.org/meta-schemas/core.yaml# -title: Mediatek MT65xx Pin Controller +title: MediaTek MT65xx Pin Controller maintainers: - Sean Wang <sean.wang@kernel.org> -description: |+ - The Mediatek's Pin controller is used to control SoC pins. +description: + The MediaTek's MT65xx Pin controller is used to control SoC pins. properties: compatible: @@ -30,7 +30,7 @@ properties: pins-are-numbered: $ref: /schemas/types.yaml#/definitions/flag - description: | + description: Specify the subnodes are using numbered pinmux to specify pins. (UNUSED) deprecated: true @@ -38,10 +38,10 @@ properties: "#gpio-cells": const: 2 - description: | - Number of cells in GPIO specifier. Since the generic GPIO - binding is used, the amount of cells must be specified as 2. See the below - mentioned gpio binding representation for description of particular cells. + description: + Number of cells in GPIO specifier. Since the generic GPIO binding is used, + the amount of cells must be specified as 2. See the below mentioned gpio + binding representation for description of particular cells. mediatek,pctl-regmap: $ref: /schemas/types.yaml#/definitions/phandle-array @@ -49,7 +49,7 @@ properties: maxItems: 1 minItems: 1 maxItems: 2 - description: | + description: Should be phandles of the syscfg node. interrupt-controller: true @@ -67,7 +67,7 @@ required: - "#gpio-cells" allOf: - - $ref: "pinctrl.yaml#" + - $ref: pinctrl.yaml# patternProperties: 'pins$': @@ -77,25 +77,25 @@ patternProperties: '(^pins|pins?$)': type: object additionalProperties: false - description: | + description: A pinctrl node should contain at least one subnodes representing the pinctrl groups available on the machine. Each subnode will list the pins it needs, and how they should be configured, with regard to muxer configuration, pullups, drive strength, input enable/disable and input schmitt. - $ref: "/schemas/pinctrl/pincfg-node.yaml" + $ref: /schemas/pinctrl/pincfg-node.yaml properties: pinmux: description: - integer array, represents gpio pin number and mux setting. + Integer array, represents gpio pin number and mux setting. Supported pin number and mux varies for different SoCs, and are - defined as macros in <soc>-pinfunc.h directly. + defined as macros in dt-bindings/pinctrl/<soc>-pinfunc.h directly. bias-disable: true bias-pull-up: - description: | + description: Besides generic pinconfig options, it can be used as the pull up settings for 2 pull resistors, R0 and R1. User can configure those special pins. Some macros have been defined for this usage, such @@ -117,7 +117,7 @@ patternProperties: input-schmitt-disable: true drive-strength: - description: | + description: Can support some arguments, such as MTK_DRIVE_4mA, MTK_DRIVE_6mA, etc. See dt-bindings/pinctrl/mt65xx.h for valid arguments. diff --git a/Documentation/devicetree/bindings/pinctrl/mediatek,mt6779-pinctrl.yaml b/Documentation/devicetree/bindings/pinctrl/mediatek,mt6779-pinctrl.yaml index a2141eb0854e..7f0e2d6cd6d9 100644 --- a/Documentation/devicetree/bindings/pinctrl/mediatek,mt6779-pinctrl.yaml +++ b/Documentation/devicetree/bindings/pinctrl/mediatek,mt6779-pinctrl.yaml @@ -4,15 +4,15 @@ $id: http://devicetree.org/schemas/pinctrl/mediatek,mt6779-pinctrl.yaml# $schema: http://devicetree.org/meta-schemas/core.yaml# -title: Mediatek MT6779 Pin Controller +title: MediaTek MT6779 Pin Controller maintainers: - Andy Teng <andy.teng@mediatek.com> - Sean Wang <sean.wang@kernel.org> description: - The MediaTek pin controller on MT6779 is used to control pin - functions, pull up/down resistance and drive strength options. + The MediaTek pin controller on MT6779 is used to control pin functions, pull + up/down resistance and drive strength options. properties: compatible: @@ -29,22 +29,22 @@ properties: "#gpio-cells": const: 2 - description: | - Number of cells in GPIO specifier. Since the generic GPIO - binding is used, the amount of cells must be specified as 2. See the below - mentioned gpio binding representation for description of particular cells. + description: + Number of cells in GPIO specifier. Since the generic GPIO binding is used, + the amount of cells must be specified as 2. See the below mentioned gpio + binding representation for description of particular cells. gpio-ranges: minItems: 1 maxItems: 5 - description: | + description: GPIO valid number range. interrupt-controller: true interrupts: maxItems: 1 - description: | + description: Specifies the summary IRQ. "#interrupt-cells": @@ -58,7 +58,7 @@ required: - "#gpio-cells" allOf: - - $ref: "pinctrl.yaml#" + - $ref: pinctrl.yaml# - if: properties: compatible: @@ -118,19 +118,20 @@ patternProperties: patternProperties: '-pins*$': type: object - description: | + description: A pinctrl node should contain at least one subnodes representing the pinctrl groups available on the machine. Each subnode will list the pins it needs, and how they should be configured, with regard to muxer - configuration, pullups, drive strength, input enable/disable and input schmitt. - $ref: "/schemas/pinctrl/pincfg-node.yaml" + configuration, pullups, drive strength, input enable/disable and input + schmitt. + $ref: /schemas/pinctrl/pincfg-node.yaml properties: pinmux: description: - integer array, represents gpio pin number and mux setting. - Supported pin number and mux varies for different SoCs, and are defined - as macros in boot/dts/<soc>-pinfunc.h directly. + Integer array, represents gpio pin number and mux setting. + Supported pin number and mux varies for different SoCs, and are + defined as macros in dt-bindings/pinctrl/<soc>-pinfunc.h directly. bias-disable: true @@ -159,7 +160,8 @@ patternProperties: mediatek,pull-up-adv: description: | Pull up setings for 2 pull resistors, R0 and R1. User can - configure those special pins. Valid arguments are described as below: + configure those special pins. Valid arguments are described as + below: 0: (R1, R0) = (0, 0) which means R1 disabled and R0 disabled. 1: (R1, R0) = (0, 1) which means R1 disabled and R0 enabled. 2: (R1, R0) = (1, 0) which means R1 enabled and R0 disabled. @@ -170,7 +172,8 @@ patternProperties: mediatek,pull-down-adv: description: | Pull down settings for 2 pull resistors, R0 and R1. User can - configure those special pins. Valid arguments are described as below: + configure those special pins. Valid arguments are described as + below: 0: (R1, R0) = (0, 0) which means R1 disabled and R0 disabled. 1: (R1, R0) = (0, 1) which means R1 disabled and R0 enabled. 2: (R1, R0) = (1, 0) which means R1 enabled and R0 disabled. diff --git a/Documentation/devicetree/bindings/pinctrl/mediatek,pinctrl-mt6795.yaml b/Documentation/devicetree/bindings/pinctrl/mediatek,mt6795-pinctrl.yaml index 9399e0215526..601d86aecdd4 100644 --- a/Documentation/devicetree/bindings/pinctrl/mediatek,pinctrl-mt6795.yaml +++ b/Documentation/devicetree/bindings/pinctrl/mediatek,mt6795-pinctrl.yaml @@ -1,17 +1,17 @@ # SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) %YAML 1.2 --- -$id: http://devicetree.org/schemas/pinctrl/mediatek,pinctrl-mt6795.yaml# +$id: http://devicetree.org/schemas/pinctrl/mediatek,mt6795-pinctrl.yaml# $schema: http://devicetree.org/meta-schemas/core.yaml# -title: Mediatek MT6795 Pin Controller +title: MediaTek MT6795 Pin Controller maintainers: - AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com> - Sean Wang <sean.wang@kernel.org> -description: | - The Mediatek's Pin controller is used to control SoC pins. +description: + The MediaTek's MT6795 Pin controller is used to control SoC pins. properties: compatible: @@ -20,10 +20,10 @@ properties: gpio-controller: true '#gpio-cells': - description: | + description: Number of cells in GPIO specifier. Since the generic GPIO binding is used, - the amount of cells must be specified as 2. See the below - mentioned gpio binding representation for description of particular cells. + the amount of cells must be specified as 2. See the below mentioned gpio + binding representation for description of particular cells. const: 2 gpio-ranges: @@ -32,7 +32,7 @@ properties: reg: description: - Physical address base for gpio base and eint registers. + Physical address base for GPIO base and eint registers. minItems: 2 reg-names: @@ -65,8 +65,8 @@ patternProperties: A pinctrl node should contain at least one subnodes representing the pinctrl groups available on the machine. Each subnode will list the pins it needs, and how they should be configured, with regard to muxer - configuration, pullups, drive strength, input enable/disable and - input schmitt. + configuration, pullups, drive strength, input enable/disable and input + schmitt. An example of using macro: pincontroller { /* GPIO0 set as multifunction GPIO0 */ @@ -82,15 +82,14 @@ patternProperties: } }; }; - $ref: "pinmux-node.yaml" + $ref: pinmux-node.yaml properties: pinmux: - description: | + description: Integer array, represents gpio pin number and mux setting. Supported pin number and mux varies for different SoCs, and are - defined as macros in dt-bindings/pinctrl/<soc>-pinfunc.h - directly. + defined as macros in dt-bindings/pinctrl/<soc>-pinfunc.h directly. drive-strength: enum: [2, 4, 6, 8, 10, 12, 14, 16] @@ -100,20 +99,20 @@ patternProperties: - type: boolean - enum: [100, 101, 102, 103] description: mt6795 pull down PUPD/R0/R1 type define value. - description: | - For normal pull down type, it is not necessary to specify R1R0 - values; When pull down type is PUPD/R0/R1, adding R1R0 defines - will set different resistance values. + description: + For normal pull down type, it is not necessary to specify R1R0 + values; When pull down type is PUPD/R0/R1, adding R1R0 defines + will set different resistance values. bias-pull-up: oneOf: - type: boolean - enum: [100, 101, 102, 103] description: mt6795 pull up PUPD/R0/R1 type define value. - description: | - For normal pull up type, it is not necessary to specify R1R0 - values; When pull up type is PUPD/R0/R1, adding R1R0 defines - will set different resistance values. + description: + For normal pull up type, it is not necessary to specify R1R0 + values; When pull up type is PUPD/R0/R1, adding R1R0 defines will + set different resistance values. bias-disable: true @@ -132,7 +131,8 @@ patternProperties: mediatek,pull-up-adv: description: | Pull up setings for 2 pull resistors, R0 and R1. User can - configure those special pins. Valid arguments are described as below: + configure those special pins. Valid arguments are described as + below: 0: (R1, R0) = (0, 0) which means R1 disabled and R0 disabled. 1: (R1, R0) = (0, 1) which means R1 disabled and R0 enabled. 2: (R1, R0) = (1, 0) which means R1 enabled and R0 disabled. @@ -143,7 +143,8 @@ patternProperties: mediatek,pull-down-adv: description: | Pull down settings for 2 pull resistors, R0 and R1. User can - configure those special pins. Valid arguments are described as below: + configure those special pins. Valid arguments are described as + below: 0: (R1, R0) = (0, 0) which means R1 disabled and R0 disabled. 1: (R1, R0) = (0, 1) which means R1 disabled and R0 enabled. 2: (R1, R0) = (1, 0) which means R1 enabled and R0 disabled. @@ -155,7 +156,7 @@ patternProperties: - pinmux allOf: - - $ref: "pinctrl.yaml#" + - $ref: pinctrl.yaml# required: - compatible diff --git a/Documentation/devicetree/bindings/pinctrl/mediatek,mt7620-pinctrl.yaml b/Documentation/devicetree/bindings/pinctrl/mediatek,mt7620-pinctrl.yaml new file mode 100644 index 000000000000..591bc0664ec6 --- /dev/null +++ b/Documentation/devicetree/bindings/pinctrl/mediatek,mt7620-pinctrl.yaml @@ -0,0 +1,298 @@ +# SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/pinctrl/mediatek,mt7620-pinctrl.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: MediaTek MT7620 Pin Controller + +maintainers: + - Arınç ÜNAL <arinc.unal@arinc9.com> + - Sergio Paracuellos <sergio.paracuellos@gmail.com> + +description: | + MediaTek MT7620 pin controller for MT7620 SoC. + The pin controller can only set the muxing of pin groups. Muxing individual + pins is not supported. There is no pinconf support. + +properties: + compatible: + const: ralink,mt7620-pinctrl + +patternProperties: + '-pins$': + type: object + additionalProperties: false + + patternProperties: + '^(.*-)?pinmux$': + type: object + description: node for pinctrl. + $ref: pinmux-node.yaml# + additionalProperties: false + + properties: + function: + description: + A string containing the name of the function to mux to the group. + enum: [ephy, gpio, gpio i2s, gpio uartf, i2c, i2s uartf, mdio, nand, + pa, pcie refclk, pcie rst, pcm gpio, pcm i2s, pcm uartf, + refclk, rgmii1, rgmii2, sd, spi, spi refclk, uartf, uartlite, + wdt refclk, wdt rst, wled] + + groups: + description: + An array of strings. Each string contains the name of a group. + maxItems: 1 + + required: + - groups + - function + + allOf: + - if: + properties: + function: + const: ephy + then: + properties: + groups: + enum: [ephy] + + - if: + properties: + function: + const: gpio + then: + properties: + groups: + enum: [ephy, i2c, mdio, nd_sd, pa, pcie, rgmii1, rgmii2, spi, + spi refclk, uartf, uartlite, wdt, wled] + + - if: + properties: + function: + const: gpio i2s + then: + properties: + groups: + enum: [uartf] + + - if: + properties: + function: + const: gpio uartf + then: + properties: + groups: + enum: [uartf] + + - if: + properties: + function: + const: i2c + then: + properties: + groups: + enum: [i2c] + + - if: + properties: + function: + const: i2s uartf + then: + properties: + groups: + enum: [uartf] + + - if: + properties: + function: + const: mdio + then: + properties: + groups: + enum: [mdio] + + - if: + properties: + function: + const: nand + then: + properties: + groups: + enum: [nd_sd] + + - if: + properties: + function: + const: pa + then: + properties: + groups: + enum: [pa] + + - if: + properties: + function: + const: pcie refclk + then: + properties: + groups: + enum: [pcie] + + - if: + properties: + function: + const: pcie rst + then: + properties: + groups: + enum: [pcie] + + - if: + properties: + function: + const: pcm gpio + then: + properties: + groups: + enum: [uartf] + + - if: + properties: + function: + const: pcm i2s + then: + properties: + groups: + enum: [uartf] + + - if: + properties: + function: + const: pcm uartf + then: + properties: + groups: + enum: [uartf] + + - if: + properties: + function: + const: refclk + then: + properties: + groups: + enum: [mdio] + + - if: + properties: + function: + const: rgmii1 + then: + properties: + groups: + enum: [rgmii1] + + - if: + properties: + function: + const: rgmii2 + then: + properties: + groups: + enum: [rgmii2] + + - if: + properties: + function: + const: sd + then: + properties: + groups: + enum: [nd_sd] + + - if: + properties: + function: + const: spi + then: + properties: + groups: + enum: [spi] + + - if: + properties: + function: + const: spi refclk + then: + properties: + groups: + enum: [spi refclk] + + - if: + properties: + function: + const: uartf + then: + properties: + groups: + enum: [uartf] + + - if: + properties: + function: + const: uartlite + then: + properties: + groups: + enum: [uartlite] + + - if: + properties: + function: + const: wdt refclk + then: + properties: + groups: + enum: [wdt] + + - if: + properties: + function: + const: wdt rst + then: + properties: + groups: + enum: [wdt] + + - if: + properties: + function: + const: wled + then: + properties: + groups: + enum: [wled] + +allOf: + - $ref: pinctrl.yaml# + +required: + - compatible + +additionalProperties: false + +examples: + - | + pinctrl { + compatible = "ralink,mt7620-pinctrl"; + + i2c_pins: i2c0-pins { + pinmux { + groups = "i2c"; + function = "i2c"; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/pinctrl/ralink,mt7621-pinctrl.yaml b/Documentation/devicetree/bindings/pinctrl/mediatek,mt7621-pinctrl.yaml index 1b1d37b981d9..e568b9c13727 100644 --- a/Documentation/devicetree/bindings/pinctrl/ralink,mt7621-pinctrl.yaml +++ b/Documentation/devicetree/bindings/pinctrl/mediatek,mt7621-pinctrl.yaml @@ -1,17 +1,17 @@ # SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause %YAML 1.2 --- -$id: http://devicetree.org/schemas/pinctrl/ralink,mt7621-pinctrl.yaml# +$id: http://devicetree.org/schemas/pinctrl/mediatek,mt7621-pinctrl.yaml# $schema: http://devicetree.org/meta-schemas/core.yaml# -title: Ralink MT7621 Pin Controller +title: MediaTek MT7621 Pin Controller maintainers: - Arınç ÜNAL <arinc.unal@arinc9.com> - Sergio Paracuellos <sergio.paracuellos@gmail.com> -description: - Ralink MT7621 pin controller for MT7621 SoC. +description: | + MediaTek MT7621 pin controller for MT7621 SoC. The pin controller can only set the muxing of pin groups. Muxing individual pins is not supported. There is no pinconf support. @@ -22,11 +22,14 @@ properties: patternProperties: '-pins$': type: object + additionalProperties: false + patternProperties: '^(.*-)?pinmux$': type: object description: node for pinctrl. $ref: pinmux-node.yaml# + additionalProperties: false properties: function: @@ -236,12 +239,8 @@ patternProperties: groups: enum: [wdt] - additionalProperties: false - - additionalProperties: false - allOf: - - $ref: "pinctrl.yaml#" + - $ref: pinctrl.yaml# required: - compatible diff --git a/Documentation/devicetree/bindings/pinctrl/mediatek,mt7622-pinctrl.yaml b/Documentation/devicetree/bindings/pinctrl/mediatek,mt7622-pinctrl.yaml index ac93eb8f01a6..bd72a326e6e0 100644 --- a/Documentation/devicetree/bindings/pinctrl/mediatek,mt7622-pinctrl.yaml +++ b/Documentation/devicetree/bindings/pinctrl/mediatek,mt7622-pinctrl.yaml @@ -4,12 +4,12 @@ $id: http://devicetree.org/schemas/pinctrl/mediatek,mt7622-pinctrl.yaml# $schema: http://devicetree.org/meta-schemas/core.yaml# -title: Mediatek MT7622 Pin Controller +title: MediaTek MT7622 Pin Controller maintainers: - Sean Wang <sean.wang@kernel.org> -description: |+ +description: The MediaTek's MT7622 Pin controller is used to control SoC pins. properties: @@ -29,10 +29,10 @@ properties: "#gpio-cells": const: 2 - description: | - Number of cells in GPIO specifier. Since the generic GPIO - binding is used, the amount of cells must be specified as 2. See the below - mentioned gpio binding representation for description of particular cells. + description: + Number of cells in GPIO specifier. Since the generic GPIO binding is used, + the amount of cells must be specified as 2. See the below mentioned gpio + binding representation for description of particular cells. interrupt-controller: true @@ -43,7 +43,7 @@ properties: const: 2 allOf: - - $ref: "pinctrl.yaml#" + - $ref: pinctrl.yaml# required: - compatible @@ -68,18 +68,18 @@ patternProperties: '^mux(-|$)': type: object additionalProperties: false - description: | + description: pinmux configuration nodes. - $ref: "/schemas/pinctrl/pinmux-node.yaml" + $ref: /schemas/pinctrl/pinmux-node.yaml properties: function: - description: | + description: A string containing the name of the function to mux to the group. enum: [emmc, eth, i2c, i2s, ir, led, flash, pcie, pmic, pwm, sd, spi, tdm, uart, watchdog, wifi] groups: - description: | + description: An array of strings. Each string contains the name of a group. drive-strength: @@ -247,18 +247,18 @@ patternProperties: '^conf(-|$)': type: object additionalProperties: false - description: | + description: pinconf configuration nodes. - $ref: "/schemas/pinctrl/pincfg-node.yaml" + $ref: /schemas/pinctrl/pincfg-node.yaml properties: groups: - description: | + description: An array of strings. Each string contains the name of a group. Valid values are the same as the pinmux node. pins: - description: | + description: An array of strings. Each string contains the name of a pin. enum: [GPIO_A, I2S1_IN, I2S1_OUT, I2S_BCLK, I2S_WS, I2S_MCLK, TXD0, RXD0, SPI_WP, SPI_HOLD, SPI_CLK, SPI_MOSI, SPI_MISO, SPI_CS, @@ -315,14 +315,14 @@ patternProperties: enum: [0, 1] mediatek,tdsel: - description: | + description: An integer describing the steps for output level shifter duty cycle when asserted (high pulse width adjustment). Valid arguments are from 0 to 15. $ref: /schemas/types.yaml#/definitions/uint32 mediatek,rdsel: - description: | + description: An integer describing the steps for input level shifter duty cycle when asserted (high pulse width adjustment). Valid arguments are from 0 to 63. diff --git a/Documentation/devicetree/bindings/pinctrl/ralink,mt7620-pinctrl.yaml b/Documentation/devicetree/bindings/pinctrl/mediatek,mt76x8-pinctrl.yaml index 1e63ea34146a..31849dd5940b 100644 --- a/Documentation/devicetree/bindings/pinctrl/ralink,mt7620-pinctrl.yaml +++ b/Documentation/devicetree/bindings/pinctrl/mediatek,mt76x8-pinctrl.yaml @@ -1,50 +1,46 @@ # SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause %YAML 1.2 --- -$id: http://devicetree.org/schemas/pinctrl/ralink,mt7620-pinctrl.yaml# +$id: http://devicetree.org/schemas/pinctrl/mediatek,mt76x8-pinctrl.yaml# $schema: http://devicetree.org/meta-schemas/core.yaml# -title: Ralink MT7620 Pin Controller +title: MediaTek MT76X8 Pin Controller maintainers: - Arınç ÜNAL <arinc.unal@arinc9.com> - Sergio Paracuellos <sergio.paracuellos@gmail.com> -description: - Ralink MT7620 pin controller for MT7620, MT7628 and MT7688 SoCs. +description: | + MediaTek MT76X8 pin controller for MT7628 and MT7688 SoCs. The pin controller can only set the muxing of pin groups. Muxing individual pins is not supported. There is no pinconf support. properties: compatible: - const: ralink,mt7620-pinctrl + const: ralink,mt76x8-pinctrl patternProperties: '-pins$': type: object + additionalProperties: false + patternProperties: '^(.*-)?pinmux$': type: object description: node for pinctrl. $ref: pinmux-node.yaml# + additionalProperties: false properties: function: description: A string containing the name of the function to mux to the group. - anyOf: - - description: For MT7620 SoC - enum: [ephy, gpio, gpio i2s, gpio uartf, i2c, i2s uartf, mdio, nand, pa, - pcie refclk, pcie rst, pcm gpio, pcm i2s, pcm uartf, refclk, - rgmii1, rgmii2, sd, spi, spi refclk, uartf, uartlite, wdt refclk, - wdt rst, wled] - - - description: For MT7628 and MT7688 SoCs - enum: [antenna, debug, gpio, i2c, i2s, jtag, p0led_an, p0led_kn, - p1led_an, p1led_kn, p2led_an, p2led_kn, p3led_an, p3led_kn, - p4led_an, p4led_kn, pcie, pcm, perst, pwm, pwm0, pwm1, pwm_uart2, - refclk, rsvd, sdxc, sdxc d5 d4, sdxc d6, sdxc d7, spi, spi cs1, - spis, sw_r, uart0, uart1, uart2, utif, wdt, wled_an, wled_kn, -] + enum: [antenna, debug, gpio, i2c, i2s, jtag, p0led_an, p0led_kn, + p1led_an, p1led_kn, p2led_an, p2led_kn, p3led_an, p3led_kn, + p4led_an, p4led_kn, pcie, pcm, perst, pwm, pwm0, pwm1, + pwm_uart2, refclk, rsvd, sdxc, sdxc d5 d4, sdxc d6, sdxc d7, + spi, spi cs1, spis, sw_r, uart0, uart1, uart2, utif, wdt, + wled_an, wled_kn, -] groups: description: @@ -77,48 +73,15 @@ patternProperties: - if: properties: function: - const: ephy - then: - properties: - groups: - enum: [ephy] - - - if: - properties: - function: const: gpio then: properties: groups: - anyOf: - - description: For MT7620 SoC - enum: [ephy, i2c, mdio, nd_sd, pa, pcie, rgmii1, rgmii2, - spi, spi refclk, uartf, uartlite, wdt, wled] - - - description: For MT7628 and MT7688 SoCs - enum: [gpio, i2c, i2s, p0led_an, p0led_kn, p1led_an, - p1led_kn, p2led_an, p2led_kn, p3led_an, p3led_kn, - p4led_an, p4led_kn, perst, pwm0, pwm1, refclk, - sdmode, spi, spi cs1, spis, uart0, uart1, uart2, - wdt, wled_an, wled_kn] - - - if: - properties: - function: - const: gpio i2s - then: - properties: - groups: - enum: [uartf] - - - if: - properties: - function: - const: gpio uartf - then: - properties: - groups: - enum: [uartf] + enum: [gpio, i2c, i2s, p0led_an, p0led_kn, p1led_an, p1led_kn, + p2led_an, p2led_kn, p3led_an, p3led_kn, p4led_an, + p4led_kn, perst, pwm0, pwm1, refclk, sdmode, spi, + spi cs1, spis, uart0, uart1, uart2, wdt, wled_an, + wled_kn] - if: properties: @@ -141,15 +104,6 @@ patternProperties: - if: properties: function: - const: i2s uartf - then: - properties: - groups: - enum: [uartf] - - - if: - properties: - function: const: jtag then: properties: @@ -161,24 +115,6 @@ patternProperties: - if: properties: function: - const: mdio - then: - properties: - groups: - enum: [mdio] - - - if: - properties: - function: - const: nand - then: - properties: - groups: - enum: [nd_sd] - - - if: - properties: - function: const: p0led_an then: properties: @@ -269,15 +205,6 @@ patternProperties: - if: properties: function: - const: pa - then: - properties: - groups: - enum: [pa] - - - if: - properties: - function: const: pcie then: properties: @@ -287,24 +214,6 @@ patternProperties: - if: properties: function: - const: pcie refclk - then: - properties: - groups: - enum: [pcie] - - - if: - properties: - function: - const: pcie rst - then: - properties: - groups: - enum: [pcie] - - - if: - properties: - function: const: pcm then: properties: @@ -314,33 +223,6 @@ patternProperties: - if: properties: function: - const: pcm gpio - then: - properties: - groups: - enum: [uartf] - - - if: - properties: - function: - const: pcm i2s - then: - properties: - groups: - enum: [uartf] - - - if: - properties: - function: - const: pcm uartf - then: - properties: - groups: - enum: [uartf] - - - if: - properties: - function: const: perst then: properties: @@ -390,30 +272,7 @@ patternProperties: then: properties: groups: - anyOf: - - description: For MT7620 SoC - enum: [mdio] - - - description: For MT7628 and MT7688 SoCs - enum: [gpio, refclk, spi cs1] - - - if: - properties: - function: - const: rgmii1 - then: - properties: - groups: - enum: [rgmii1] - - - if: - properties: - function: - const: rgmii2 - then: - properties: - groups: - enum: [rgmii2] + enum: [gpio, refclk, spi cs1] - if: properties: @@ -427,15 +286,6 @@ patternProperties: - if: properties: function: - const: sd - then: - properties: - groups: - enum: [nd_sd] - - - if: - properties: - function: const: sdxc then: properties: @@ -490,15 +340,6 @@ patternProperties: - if: properties: function: - const: spi refclk - then: - properties: - groups: - enum: [spi refclk] - - - if: - properties: - function: const: spis then: properties: @@ -544,24 +385,6 @@ patternProperties: - if: properties: function: - const: uartf - then: - properties: - groups: - enum: [uartf] - - - if: - properties: - function: - const: uartlite - then: - properties: - groups: - enum: [uartlite] - - - if: - properties: - function: const: utif then: properties: @@ -581,33 +404,6 @@ patternProperties: - if: properties: function: - const: wdt refclk - then: - properties: - groups: - enum: [wdt] - - - if: - properties: - function: - const: wdt rst - then: - properties: - groups: - enum: [wdt] - - - if: - properties: - function: - const: wled - then: - properties: - groups: - enum: [wled] - - - if: - properties: - function: const: wled_an then: properties: @@ -632,12 +428,8 @@ patternProperties: groups: enum: [i2c, spi cs1, uart0] - additionalProperties: false - - additionalProperties: false - allOf: - - $ref: "pinctrl.yaml#" + - $ref: pinctrl.yaml# required: - compatible @@ -647,7 +439,7 @@ additionalProperties: false examples: - | pinctrl { - compatible = "ralink,mt7620-pinctrl"; + compatible = "ralink,mt76x8-pinctrl"; i2c_pins: i2c0-pins { pinmux { diff --git a/Documentation/devicetree/bindings/pinctrl/mediatek,mt7981-pinctrl.yaml b/Documentation/devicetree/bindings/pinctrl/mediatek,mt7981-pinctrl.yaml index 74c66fbcb2ae..10717cee9058 100644 --- a/Documentation/devicetree/bindings/pinctrl/mediatek,mt7981-pinctrl.yaml +++ b/Documentation/devicetree/bindings/pinctrl/mediatek,mt7981-pinctrl.yaml @@ -4,7 +4,7 @@ $id: http://devicetree.org/schemas/pinctrl/mediatek,mt7981-pinctrl.yaml# $schema: http://devicetree.org/meta-schemas/core.yaml# -title: Mediatek MT7981 Pin Controller +title: MediaTek MT7981 Pin Controller maintainers: - Daniel Golle <daniel@makrotopia.org> @@ -37,7 +37,7 @@ properties: "#gpio-cells": const: 2 - description: > + description: Number of cells in GPIO specifier. Since the generic GPIO binding is used, the amount of cells must be specified as 2. See the below mentioned gpio binding representation for description of particular cells. @@ -111,7 +111,9 @@ patternProperties: "watchdog1" "watchdog" 13 "udi" "udi" 9, 10, 11, 12, 13 "drv_vbus" "usb" 14 - "emmc_45" "flash" 15, 16, 17, 18, 19, 20, 21, 22, 23, 24, 25 + "emmc_45" "flash" 15, 16, 17, 18, 19, 20, 21, 22, 23, + 24, 25 + "snfi" "flash" 16, 17, 18, 19, 20, 21 "spi0" "spi" 16, 17, 18, 19 "spi0_wp_hold" "spi" 20, 21 @@ -148,7 +150,7 @@ patternProperties: "wf5g_led0" "led" 31 "wf5g_led1" "led" 35 "mt7531_int" "eth" 38 - "ant_sel" "ant" 14, 15, 16, 17, 18, 19, 20, 21, 22 + "ant_sel" "ant" 14, 15, 16, 17, 18, 19, 20, 21, 22, 23, 24, 25, 34, 35 $ref: /schemas/pinctrl/pinmux-node.yaml @@ -256,7 +258,8 @@ patternProperties: then: properties: groups: - enum: [gbe_led0, gbe_led1, wf2g_led0, wf2g_led1, wf5g_led0, wf5g_led1] + enum: [gbe_led0, gbe_led1, wf2g_led0, wf2g_led1, wf5g_led0, + wf5g_led1] - if: properties: function: @@ -275,7 +278,8 @@ patternProperties: properties: groups: items: - enum: [spi1_0, spi0, spi0_wp_hold, spi1_1, spi2, spi2_wp_hold] + enum: [spi1_0, spi0, spi0_wp_hold, spi1_1, spi2, + spi2_wp_hold] maxItems: 4 - if: properties: @@ -332,13 +336,14 @@ patternProperties: JTAG_JTDO, JTAG_JTDI, JTAG_JTMS, JTAG_JTCLK, JTAG_JTRST_N, WO_JTAG_JTDO, WO_JTAG_JTDI, WO_JTAG_JTMS, WO_JTAG_JTCLK, WO_JTAG_JTRST_N, USB_VBUS, PWM0, SPI0_CLK, SPI0_MOSI, - SPI0_MISO, SPI0_CS, SPI0_HOLD, SPI0_WP, SPI1_CLK, SPI1_MOSI, - SPI1_MISO, SPI1_CS, SPI2_CLK, SPI2_MOSI, SPI2_MISO, SPI2_CS, - SPI2_HOLD, SPI2_WP, UART0_RXD, UART0_TXD, PCIE_CLK_REQ, - PCIE_WAKE_N, SMI_MDC, SMI_MDIO, GBE_INT, GBE_RESET, - WF_DIG_RESETB, WF_CBA_RESETB, WF_XO_REQ, WF_TOP_CLK, - WF_TOP_DATA, WF_HB1, WF_HB2, WF_HB3, WF_HB4, WF_HB0, - WF_HB0_B, WF_HB5, WF_HB6, WF_HB7, WF_HB8, WF_HB9, WF_HB10] + SPI0_MISO, SPI0_CS, SPI0_HOLD, SPI0_WP, SPI1_CLK, + SPI1_MOSI, SPI1_MISO, SPI1_CS, SPI2_CLK, SPI2_MOSI, + SPI2_MISO, SPI2_CS, SPI2_HOLD, SPI2_WP, UART0_RXD, + UART0_TXD, PCIE_CLK_REQ, PCIE_WAKE_N, SMI_MDC, SMI_MDIO, + GBE_INT, GBE_RESET, WF_DIG_RESETB, WF_CBA_RESETB, + WF_XO_REQ, WF_TOP_CLK, WF_TOP_DATA, WF_HB1, WF_HB2, WF_HB3, + WF_HB4, WF_HB0, WF_HB0_B, WF_HB5, WF_HB6, WF_HB7, WF_HB8, + WF_HB9, WF_HB10] maxItems: 57 bias-disable: true @@ -348,7 +353,7 @@ patternProperties: - type: boolean description: normal pull up. - enum: [100, 101, 102, 103] - description: > + description: PUPD/R1/R0 pull down type. See MTK_PUPD_SET_R1R0 defines in dt-bindings/pinctrl/mt65xx.h. @@ -357,7 +362,7 @@ patternProperties: - type: boolean description: normal pull down. - enum: [100, 101, 102, 103] - description: > + description: PUPD/R1/R0 pull down type. See MTK_PUPD_SET_R1R0 defines in dt-bindings/pinctrl/mt65xx.h. diff --git a/Documentation/devicetree/bindings/pinctrl/mediatek,mt7986-pinctrl.yaml b/Documentation/devicetree/bindings/pinctrl/mediatek,mt7986-pinctrl.yaml index 216b356cd519..0f615ada290a 100644 --- a/Documentation/devicetree/bindings/pinctrl/mediatek,mt7986-pinctrl.yaml +++ b/Documentation/devicetree/bindings/pinctrl/mediatek,mt7986-pinctrl.yaml @@ -4,12 +4,12 @@ $id: http://devicetree.org/schemas/pinctrl/mediatek,mt7986-pinctrl.yaml# $schema: http://devicetree.org/meta-schemas/core.yaml# -title: Mediatek MT7986 Pin Controller +title: MediaTek MT7986 Pin Controller maintainers: - Sean Wang <sean.wang@kernel.org> -description: |+ +description: The MediaTek's MT7986 Pin controller is used to control SoC pins. properties: @@ -37,15 +37,15 @@ properties: "#gpio-cells": const: 2 - description: | - Number of cells in GPIO specifier. Since the generic GPIO - binding is used, the amount of cells must be specified as 2. See the below - mentioned gpio binding representation for description of particular cells. + description: + Number of cells in GPIO specifier. Since the generic GPIO binding is used, + the amount of cells must be specified as 2. See the below mentioned gpio + binding representation for description of particular cells. gpio-ranges: minItems: 1 maxItems: 5 - description: | + description: GPIO valid number range. interrupt-controller: true @@ -57,7 +57,7 @@ properties: const: 2 allOf: - - $ref: "pinctrl.yaml#" + - $ref: pinctrl.yaml# required: - compatible @@ -72,7 +72,7 @@ patternProperties: additionalProperties: false patternProperties: - '.*mux.*': + '^.*mux.*$': type: object additionalProperties: false description: | @@ -81,7 +81,7 @@ patternProperties: The following table shows the effective values of "group", "function" properties and chip pinout pins - groups function pins (in pin#) + groups function pins (in pin#) --------------------------------------------------------------------- "watchdog" "watchdog" 0 "wifi_led" "led" 1, 2 @@ -97,8 +97,9 @@ patternProperties: "pwm1_0" "pwm" 22, "snfi" "flash" 23, 24, 25, 26, 27, 28 "spi1_2" "spi" 29, 30, 31, 32 - "emmc_45" "emmc" 22, 23, 24, 25, 26, 27, 28, 29, 30, - 31, 32 + "emmc_45" "emmc" 22, 23, 24, 25, 26, 27, 28, 29, 30, 31, + 32 + "spi1_1" "spi" 23, 24, 25, 26 "uart1_2_rx_tx" "uart" 29, 30 "uart1_2_cts_rts" "uart" 31, 32 @@ -115,8 +116,9 @@ patternProperties: "pcie_pereset" "pcie" 41 "uart1" "uart" 42, 43, 44, 45 "uart2" "uart" 46, 47, 48, 49 - "emmc_51" "emmc" 50, 51, 52, 53, 54, 55, 56, 57, 57, - 59, 60, 61 + "emmc_51" "emmc" 50, 51, 52, 53, 54, 55, 56, 57, 58, 59, + 60, 61 + "pcm" "audio" 62, 63, 64, 65 "i2s" "audio" 62, 63, 64, 65 "switch_int" "eth" 66 @@ -126,21 +128,20 @@ patternProperties: "wf_dbdc" "wifi" 74, 75, 76, 77, 78, 79, 80, 81, 82, 83, 84, 85 - $ref: "/schemas/pinctrl/pinmux-node.yaml" + $ref: /schemas/pinctrl/pinmux-node.yaml properties: function: - description: | + description: A string containing the name of the function to mux to the group. There is no "audio", "pcie" functions on mt7986b, you can only use those functions on mt7986a. enum: [audio, emmc, eth, i2c, led, flash, pcie, pwm, spi, uart, watchdog, wifi] groups: - description: | + description: An array of strings. Each string contains the name of a group. - There is no "pcie_pereset", "uart1", "uart2" "emmc_51", "pcm", - and "i2s" groups on mt7986b, you can only use those groups on - mt7986a. + There is no "pcie_pereset", "uart1", "uart2" "emmc_51", "pcm", and + "i2s" groups on mt7986b, you can only use those groups on mt7986a. required: - function - groups @@ -255,32 +256,33 @@ patternProperties: items: enum: [wf_2g, wf_5g, wf_dbdc] maxItems: 3 - '.*conf.*': + '^.*conf.*$': type: object additionalProperties: false - description: | + description: pinconf configuration nodes. - $ref: "/schemas/pinctrl/pincfg-node.yaml" + $ref: /schemas/pinctrl/pincfg-node.yaml properties: pins: - description: | - An array of strings. Each string contains the name of a pin. - There is no PIN 41 to PIN 65 above on mt7686b, you can only use - those pins on mt7986a. + description: + An array of strings. Each string contains the name of a pin. There + is no PIN 41 to PIN 65 above on mt7686b, you can only use those + pins on mt7986a. items: enum: [SYS_WATCHDOG, WF2G_LED, WF5G_LED, I2C_SCL, I2C_SDA, GPIO_0, GPIO_1, GPIO_2, GPIO_3, GPIO_4, GPIO_5, GPIO_6, GPIO_7, - GPIO_8, GPIO_9, GPIO_10, GPIO_11, GPIO_12, GPIO_13, GPIO_14, - GPIO_15, PWM0, PWM1, SPI0_CLK, SPI0_MOSI, SPI0_MISO, SPI0_CS, - SPI0_HOLD, SPI0_WP, SPI1_CLK, SPI1_MOSI, SPI1_MISO, SPI1_CS, - SPI2_CLK, SPI2_MOSI, SPI2_MISO, SPI2_CS, SPI2_HOLD, SPI2_WP, - UART0_RXD, UART0_TXD, PCIE_PERESET_N, UART1_RXD, UART1_TXD, - UART1_CTS, UART1_RTS, UART2_RXD, UART2_TXD, UART2_CTS, - UART2_RTS, EMMC_DATA_0, EMMC_DATA_1, EMMC_DATA_2, - EMMC_DATA_3, EMMC_DATA_4, EMMC_DATA_5, EMMC_DATA_6, - EMMC_DATA_7, EMMC_CMD, EMMC_CK, EMMC_DSL, EMMC_RSTB, PCM_DTX, - PCM_DRX, PCM_CLK, PCM_FS, MT7531_INT, SMI_MDC, SMI_MDIO, + GPIO_8, GPIO_9, GPIO_10, GPIO_11, GPIO_12, GPIO_13, + GPIO_14, GPIO_15, PWM0, PWM1, SPI0_CLK, SPI0_MOSI, + SPI0_MISO, SPI0_CS, SPI0_HOLD, SPI0_WP, SPI1_CLK, + SPI1_MOSI, SPI1_MISO, SPI1_CS, SPI2_CLK, SPI2_MOSI, + SPI2_MISO, SPI2_CS, SPI2_HOLD, SPI2_WP, UART0_RXD, + UART0_TXD, PCIE_PERESET_N, UART1_RXD, UART1_TXD, UART1_CTS, + UART1_RTS, UART2_RXD, UART2_TXD, UART2_CTS, UART2_RTS, + EMMC_DATA_0, EMMC_DATA_1, EMMC_DATA_2, EMMC_DATA_3, + EMMC_DATA_4, EMMC_DATA_5, EMMC_DATA_6, EMMC_DATA_7, + EMMC_CMD, EMMC_CK, EMMC_DSL, EMMC_RSTB, PCM_DTX, PCM_DRX, + PCM_CLK, PCM_FS, MT7531_INT, SMI_MDC, SMI_MDIO, WF0_DIG_RESETB, WF0_CBA_RESETB, WF0_XO_REQ, WF0_TOP_CLK, WF0_TOP_DATA, WF0_HB1, WF0_HB2, WF0_HB3, WF0_HB4, WF0_HB0, WF0_HB0_B, WF0_HB5, WF0_HB6, WF0_HB7, WF0_HB8, WF0_HB9, @@ -297,7 +299,7 @@ patternProperties: - type: boolean description: normal pull up. - enum: [100, 101, 102, 103] - description: | + description: PUPD/R1/R0 pull down type. See MTK_PUPD_SET_R1R0 defines in dt-bindings/pinctrl/mt65xx.h. @@ -306,7 +308,7 @@ patternProperties: - type: boolean description: normal pull down. - enum: [100, 101, 102, 103] - description: | + description: PUPD/R1/R0 pull down type. See MTK_PUPD_SET_R1R0 defines in dt-bindings/pinctrl/mt65xx.h. diff --git a/Documentation/devicetree/bindings/pinctrl/mediatek,mt8183-pinctrl.yaml b/Documentation/devicetree/bindings/pinctrl/mediatek,mt8183-pinctrl.yaml index c30cd0d010dd..ff24cf29eea7 100644 --- a/Documentation/devicetree/bindings/pinctrl/mediatek,mt8183-pinctrl.yaml +++ b/Documentation/devicetree/bindings/pinctrl/mediatek,mt8183-pinctrl.yaml @@ -4,12 +4,12 @@ $id: http://devicetree.org/schemas/pinctrl/mediatek,mt8183-pinctrl.yaml# $schema: http://devicetree.org/meta-schemas/core.yaml# -title: Mediatek MT8183 Pin Controller +title: MediaTek MT8183 Pin Controller maintainers: - Sean Wang <sean.wang@kernel.org> -description: |+ +description: The MediaTek's MT8183 Pin controller is used to control SoC pins. properties: @@ -37,15 +37,15 @@ properties: "#gpio-cells": const: 2 - description: | - Number of cells in GPIO specifier. Since the generic GPIO - binding is used, the amount of cells must be specified as 2. See the below - mentioned gpio binding representation for description of particular cells. + description: + Number of cells in GPIO specifier. Since the generic GPIO binding is used, + the amount of cells must be specified as 2. See the below mentioned gpio + binding representation for description of particular cells. gpio-ranges: minItems: 1 maxItems: 5 - description: | + description: GPIO valid number range. interrupt-controller: true @@ -57,7 +57,7 @@ properties: const: 2 allOf: - - $ref: "pinctrl.yaml#" + - $ref: pinctrl.yaml# required: - compatible @@ -74,18 +74,18 @@ patternProperties: '^pins': type: object additionalProperties: false - description: | + description: A pinctrl node should contain at least one subnodes representing the pinctrl groups available on the machine. Each subnode will list the pins it needs, and how they should be configured, with regard to muxer configuration, pullups, drive strength, input enable/disable and input schmitt. - $ref: "/schemas/pinctrl/pincfg-node.yaml" + $ref: /schemas/pinctrl/pincfg-node.yaml properties: pinmux: description: - integer array, represents gpio pin number and mux setting. + Integer array, represents gpio pin number and mux setting. Supported pin number and mux varies for different SoCs, and are defined as macros in <soc>-pinfunc.h directly. @@ -110,8 +110,13 @@ patternProperties: drive-strength: enum: [2, 4, 6, 8, 10, 12, 14, 16] + drive-strength-microamp: + enum: [125, 250, 500, 1000] + mediatek,drive-strength-adv: + deprecated: true description: | + DEPRECATED: Please use drive-strength-microamp instead. Describe the specific driving setup property. For I2C pins, the existing generic driving setup can only support 2/4/6/8/10/12/14/16mA driving. But in specific driving setup, they @@ -139,7 +144,8 @@ patternProperties: mediatek,pull-up-adv: description: | Pull up setings for 2 pull resistors, R0 and R1. User can - configure those special pins. Valid arguments are described as below: + configure those special pins. Valid arguments are described as + below: 0: (R1, R0) = (0, 0) which means R1 disabled and R0 disabled. 1: (R1, R0) = (0, 1) which means R1 disabled and R0 enabled. 2: (R1, R0) = (1, 0) which means R1 enabled and R0 disabled. @@ -150,7 +156,8 @@ patternProperties: mediatek,pull-down-adv: description: | Pull down settings for 2 pull resistors, R0 and R1. User can - configure those special pins. Valid arguments are described as below: + configure those special pins. Valid arguments are described as + below: 0: (R1, R0) = (0, 0) which means R1 disabled and R0 disabled. 1: (R1, R0) = (0, 1) which means R1 disabled and R0 enabled. 2: (R1, R0) = (1, 0) which means R1 enabled and R0 disabled. @@ -159,14 +166,14 @@ patternProperties: enum: [0, 1, 2, 3] mediatek,tdsel: - description: | + description: An integer describing the steps for output level shifter duty cycle when asserted (high pulse width adjustment). Valid arguments are from 0 to 15. $ref: /schemas/types.yaml#/definitions/uint32 mediatek,rdsel: - description: | + description: An integer describing the steps for input level shifter duty cycle when asserted (high pulse width adjustment). Valid arguments are from 0 to 63. @@ -215,7 +222,7 @@ examples: pinmux = <PINMUX_GPIO48__FUNC_SCL5>, <PINMUX_GPIO49__FUNC_SDA5>; mediatek,pull-up-adv = <3>; - mediatek,drive-strength-adv = <7>; + drive-strength-microamp = <1000>; }; }; @@ -224,7 +231,6 @@ examples: pinmux = <PINMUX_GPIO50__FUNC_SCL3>, <PINMUX_GPIO51__FUNC_SDA3>; mediatek,pull-down-adv = <2>; - mediatek,drive-strength-adv = <4>; }; }; }; diff --git a/Documentation/devicetree/bindings/pinctrl/pinctrl-mt8186.yaml b/Documentation/devicetree/bindings/pinctrl/mediatek,mt8186-pinctrl.yaml index 26573a793b57..69136ddd0bbc 100644 --- a/Documentation/devicetree/bindings/pinctrl/pinctrl-mt8186.yaml +++ b/Documentation/devicetree/bindings/pinctrl/mediatek,mt8186-pinctrl.yaml @@ -1,16 +1,16 @@ # SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) %YAML 1.2 --- -$id: http://devicetree.org/schemas/pinctrl/pinctrl-mt8186.yaml# +$id: http://devicetree.org/schemas/pinctrl/mediatek,mt8186-pinctrl.yaml# $schema: http://devicetree.org/meta-schemas/core.yaml# -title: Mediatek MT8186 Pin Controller +title: MediaTek MT8186 Pin Controller maintainers: - Sean Wang <sean.wang@mediatek.com> -description: | - The Mediatek's Pin controller is used to control SoC pins. +description: + The MediaTek's MT8186 Pin controller is used to control SoC pins. properties: compatible: @@ -19,10 +19,10 @@ properties: gpio-controller: true '#gpio-cells': - description: | + description: Number of cells in GPIO specifier. Since the generic GPIO binding is used, - the amount of cells must be specified as 2. See the below - mentioned gpio binding representation for description of particular cells. + the amount of cells must be specified as 2. See the below mentioned gpio + binding representation for description of particular cells. const: 2 gpio-ranges: @@ -31,14 +31,14 @@ properties: gpio-line-names: true reg: - description: | - Physical address base for gpio base registers. There are 8 different GPIO + description: + Physical address base for GPIO base registers. There are 8 different GPIO physical address base in mt8186. maxItems: 8 reg-names: - description: | - Gpio base register names. + description: + GPIO base register names. items: - const: iocfg0 - const: iocfg_lt @@ -60,9 +60,9 @@ properties: mediatek,rsel-resistance-in-si-unit: type: boolean - description: | - Identifying i2c pins pull up/down type which is RSEL. It can support - RSEL define or si unit value(ohm) to set different resistance. + description: + Identifying i2c pins pull up/down type which is RSEL. It can support RSEL + define or si unit value(ohm) to set different resistance. # PIN CONFIGURATION NODES patternProperties: @@ -77,8 +77,8 @@ patternProperties: A pinctrl node should contain at least one subnodes representing the pinctrl groups available on the machine. Each subnode will list the pins it needs, and how they should be configured, with regard to muxer - configuration, pullups, drive strength, input enable/disable and - input schmitt. + configuration, pullups, drive strength, input enable/disable and input + schmitt. An example of using macro: pincontroller { /* GPIO0 set as multifunction GPIO0 */ @@ -94,15 +94,14 @@ patternProperties: } }; }; - $ref: "pinmux-node.yaml" + $ref: pinmux-node.yaml properties: pinmux: - description: | + description: Integer array, represents gpio pin number and mux setting. Supported pin number and mux varies for different SoCs, and are - defined as macros in dt-bindings/pinctrl/<soc>-pinfunc.h - directly. + defined as macros in dt-bindings/pinctrl/<soc>-pinfunc.h directly. drive-strength: enum: [2, 4, 6, 8, 10, 12, 14, 16] @@ -129,10 +128,10 @@ patternProperties: For pull down type is RSEL, it can add RSEL define & resistance value(ohm) to set different resistance by identifying property "mediatek,rsel-resistance-in-si-unit". - It can support "MTK_PULL_SET_RSEL_000" & "MTK_PULL_SET_RSEL_001" - & "MTK_PULL_SET_RSEL_010" & "MTK_PULL_SET_RSEL_011" - define in mt8186. It can also support resistance value(ohm) - "75000" & "5000" in mt8186. + It can support "MTK_PULL_SET_RSEL_000" & "MTK_PULL_SET_RSEL_001" & + "MTK_PULL_SET_RSEL_010" & "MTK_PULL_SET_RSEL_011" define in + mt8186. It can also support resistance value(ohm) "75000" & "5000" + in mt8186. An example of using RSEL define: pincontroller { i2c0_pin { @@ -174,10 +173,10 @@ patternProperties: For pull up type is RSEL, it can add RSEL define & resistance value(ohm) to set different resistance by identifying property "mediatek,rsel-resistance-in-si-unit". - It can support "MTK_PULL_SET_RSEL_000" & "MTK_PULL_SET_RSEL_001" - & "MTK_PULL_SET_RSEL_010" & "MTK_PULL_SET_RSEL_011" - define in mt8186. It can also support resistance value(ohm) - "1000" & "5000" & "10000" & "75000" in mt8186. + It can support "MTK_PULL_SET_RSEL_000" & "MTK_PULL_SET_RSEL_001" & + "MTK_PULL_SET_RSEL_010" & "MTK_PULL_SET_RSEL_011" define in + mt8186. It can also support resistance value(ohm) "1000" & "5000" + & "10000" & "75000" in mt8186. An example of using si unit resistance value(ohm): &pio { mediatek,rsel-resistance-in-si-unit; diff --git a/Documentation/devicetree/bindings/pinctrl/mediatek,mt8188-pinctrl.yaml b/Documentation/devicetree/bindings/pinctrl/mediatek,mt8188-pinctrl.yaml index 7e750f1e643d..e994b0c70dbf 100644 --- a/Documentation/devicetree/bindings/pinctrl/mediatek,mt8188-pinctrl.yaml +++ b/Documentation/devicetree/bindings/pinctrl/mediatek,mt8188-pinctrl.yaml @@ -9,7 +9,7 @@ title: MediaTek MT8188 Pin Controller maintainers: - Hui Liu <hui.liu@mediatek.com> -description: | +description: The MediaTek's MT8188 Pin controller is used to control SoC pins. properties: @@ -19,10 +19,10 @@ properties: gpio-controller: true '#gpio-cells': - description: | - Number of cells in GPIO specifier, should be two. The first cell - is the pin number, the second cell is used to specify optional - parameters which are defined in <dt-bindings/gpio/gpio.h>. + description: + Number of cells in GPIO specifier, should be two. The first cell is the + pin number, the second cell is used to specify optional parameters which + are defined in <dt-bindings/gpio/gpio.h>. const: 2 gpio-ranges: @@ -59,10 +59,11 @@ properties: mediatek,rsel-resistance-in-si-unit: type: boolean - description: | - We provide two methods to select the resistance for I2C when pull up or pull down. - The first is by RSEL definition value, another one is by resistance value(ohm). - This flag is used to identify if the method is resistance(si unit) value. + description: + We provide two methods to select the resistance for I2C when pull up or + pull down. The first is by RSEL definition value, another one is by + resistance value(ohm). This flag is used to identify if the method is + resistance(si unit) value. # PIN CONFIGURATION NODES patternProperties: @@ -73,22 +74,22 @@ patternProperties: patternProperties: '^pins': type: object - $ref: "/schemas/pinctrl/pincfg-node.yaml" + $ref: /schemas/pinctrl/pincfg-node.yaml additionalProperties: false - description: | + description: A pinctrl node should contain at least one subnode representing the pinctrl groups available on the machine. Each subnode will list the pins it needs, and how they should be configured, with regard to muxer - configuration, pullups, drive strength, input enable/disable and - input schmitt. + configuration, pullups, drive strength, input enable/disable and input + schmitt. properties: pinmux: - description: | + description: Integer array, represents gpio pin number and mux setting. Supported pin number and mux varies for different SoCs, and are - defined as macros in dt-bindings/pinctrl/mediatek,<soc>-pinfunc.h - directly. + defined as macros in dt-bindings/pinctrl/mediatek,mt8188-pinfunc.h + directly, for this SoC. drive-strength: enum: [2, 4, 6, 8, 10, 12, 14, 16] @@ -106,18 +107,21 @@ patternProperties: - enum: [75000, 5000] description: mt8188 pull down RSEL type si unit value(ohm). description: | - For pull down type is normal, it doesn't need add RSEL & R1R0 define - and resistance value. + For pull down type is normal, it doesn't need add RSEL & R1R0 + define and resistance value. For pull down type is PUPD/R0/R1 type, it can add R1R0 define to set different resistance. It can support "MTK_PUPD_SET_R1R0_00" & - "MTK_PUPD_SET_R1R0_01" & "MTK_PUPD_SET_R1R0_10" & "MTK_PUPD_SET_R1R0_11" - define in mt8188. - For pull down type is RSEL, it can add RSEL define & resistance value(ohm) - to set different resistance by identifying property "mediatek,rsel-resistance-in-si-unit". - It can support "MTK_PULL_SET_RSEL_000" & "MTK_PULL_SET_RSEL_001" - & "MTK_PULL_SET_RSEL_010" & "MTK_PULL_SET_RSEL_011" & "MTK_PULL_SET_RSEL_100" - & "MTK_PULL_SET_RSEL_101" & "MTK_PULL_SET_RSEL_110" & "MTK_PULL_SET_RSEL_111" - define in mt8188. It can also support resistance value(ohm) "75000" & "5000" in mt8188. + "MTK_PUPD_SET_R1R0_01" & "MTK_PUPD_SET_R1R0_10" & + "MTK_PUPD_SET_R1R0_11" define in mt8188. + For pull down type is RSEL, it can add RSEL define & resistance + value(ohm) to set different resistance by identifying property + "mediatek,rsel-resistance-in-si-unit". It can support + "MTK_PULL_SET_RSEL_000" & "MTK_PULL_SET_RSEL_001" & + "MTK_PULL_SET_RSEL_010" & "MTK_PULL_SET_RSEL_011" & + "MTK_PULL_SET_RSEL_100" & "MTK_PULL_SET_RSEL_101" & + "MTK_PULL_SET_RSEL_110" & "MTK_PULL_SET_RSEL_111" define in + mt8188. It can also support resistance value(ohm) "75000" & "5000" + in mt8188. bias-pull-up: oneOf: @@ -131,17 +135,19 @@ patternProperties: description: | For pull up type is normal, it don't need add RSEL & R1R0 define and resistance value. - For pull up type is PUPD/R0/R1 type, it can add R1R0 define to - set different resistance. It can support "MTK_PUPD_SET_R1R0_00" & - "MTK_PUPD_SET_R1R0_01" & "MTK_PUPD_SET_R1R0_10" & "MTK_PUPD_SET_R1R0_11" - define in mt8188. - For pull up type is RSEL, it can add RSEL define & resistance value(ohm) - to set different resistance by identifying property "mediatek,rsel-resistance-in-si-unit". - It can support "MTK_PULL_SET_RSEL_000" & "MTK_PULL_SET_RSEL_001" - & "MTK_PULL_SET_RSEL_010" & "MTK_PULL_SET_RSEL_011" & "MTK_PULL_SET_RSEL_100" - & "MTK_PULL_SET_RSEL_101" & "MTK_PULL_SET_RSEL_110" & "MTK_PULL_SET_RSEL_111" - define in mt8188. It can also support resistance value(ohm) - "1000" & "1500" & "2000" & "3000" & "4000" & "5000" & "10000" & "75000" in mt8188. + For pull up type is PUPD/R0/R1 type, it can add R1R0 define to set + different resistance. It can support "MTK_PUPD_SET_R1R0_00" & + "MTK_PUPD_SET_R1R0_01" & "MTK_PUPD_SET_R1R0_10" & + "MTK_PUPD_SET_R1R0_11" define in mt8188. + For pull up type is RSEL, it can add RSEL define & resistance + value(ohm) to set different resistance by identifying property + "mediatek,rsel-resistance-in-si-unit". It can support + "MTK_PULL_SET_RSEL_000" & "MTK_PULL_SET_RSEL_001" & + "MTK_PULL_SET_RSEL_010" & "MTK_PULL_SET_RSEL_011" & + "MTK_PULL_SET_RSEL_100" & "MTK_PULL_SET_RSEL_101" & + "MTK_PULL_SET_RSEL_110" & "MTK_PULL_SET_RSEL_111" define in + mt8188. It can also support resistance value(ohm) "1000" & "1500" + & "2000" & "3000" & "4000" & "5000" & "10000" & "75000" in mt8188. bias-disable: true diff --git a/Documentation/devicetree/bindings/pinctrl/pinctrl-mt8192.yaml b/Documentation/devicetree/bindings/pinctrl/mediatek,mt8192-pinctrl.yaml index a09ebbfec574..1686427eb854 100644 --- a/Documentation/devicetree/bindings/pinctrl/pinctrl-mt8192.yaml +++ b/Documentation/devicetree/bindings/pinctrl/mediatek,mt8192-pinctrl.yaml @@ -1,16 +1,16 @@ # SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) %YAML 1.2 --- -$id: http://devicetree.org/schemas/pinctrl/pinctrl-mt8192.yaml# +$id: http://devicetree.org/schemas/pinctrl/mediatek,mt8192-pinctrl.yaml# $schema: http://devicetree.org/meta-schemas/core.yaml# -title: Mediatek MT8192 Pin Controller +title: MediaTek MT8192 Pin Controller maintainers: - Sean Wang <sean.wang@mediatek.com> -description: | - The Mediatek's Pin controller is used to control SoC pins. +description: + The MediaTek's MT8192 Pin controller is used to control SoC pins. properties: compatible: @@ -19,27 +19,27 @@ properties: gpio-controller: true '#gpio-cells': - description: | + description: Number of cells in GPIO specifier. Since the generic GPIO binding is used, - the amount of cells must be specified as 2. See the below - mentioned gpio binding representation for description of particular cells. + the amount of cells must be specified as 2. See the below mentioned gpio + binding representation for description of particular cells. const: 2 gpio-ranges: - description: gpio valid number range. + description: GPIO valid number range. maxItems: 1 gpio-line-names: true reg: - description: | - Physical address base for gpio base registers. There are 11 GPIO - physical address base in mt8192. + description: + Physical address base for GPIO base registers. There are 11 GPIO physical + address base in mt8192. maxItems: 11 reg-names: - description: | - Gpio base register names. + description: + GPIO base register names. maxItems: 11 interrupt-controller: true @@ -59,25 +59,26 @@ patternProperties: patternProperties: '^pins': type: object - description: | + description: A pinctrl node should contain at least one subnodes representing the pinctrl groups available on the machine. Each subnode will list the pins it needs, and how they should be configured, with regard to muxer - configuration, pullups, drive strength, input enable/disable and - input schmitt. - $ref: "pinmux-node.yaml" + configuration, pullups, drive strength, input enable/disable and input + schmitt. + $ref: pinmux-node.yaml properties: pinmux: - description: | + description: Integer array, represents gpio pin number and mux setting. - Supported pin number and mux varies for different SoCs, and are defined - as macros in dt-bindings/pinctrl/<soc>-pinfunc.h directly. + Supported pin number and mux varies for different SoCs, and are + defined as macros in dt-bindings/pinctrl/<soc>-pinfunc.h directly. drive-strength: - description: | - It can support some arguments, such as MTK_DRIVE_4mA, MTK_DRIVE_6mA, etc. See - dt-bindings/pinctrl/mt65xx.h. It can only support 2/4/6/8/10/12/14/16mA in mt8192. + description: + It can support some arguments, such as MTK_DRIVE_4mA, + MTK_DRIVE_6mA, etc. See dt-bindings/pinctrl/mt65xx.h. It can only + support 2/4/6/8/10/12/14/16mA in mt8192. enum: [2, 4, 6, 8, 10, 12, 14, 16] drive-strength-microamp: @@ -91,8 +92,8 @@ patternProperties: description: PUPD/R1/R0 pull down type. See MTK_PUPD_SET_R1R0_ defines in dt-bindings/pinctrl/mt65xx.h. - enum: [200, 201, 202, 203] - description: RSEL pull down type. See MTK_PULL_SET_RSEL_ - defines in dt-bindings/pinctrl/mt65xx.h. + description: RSEL pull down type. See MTK_PULL_SET_RSEL_ defines + in dt-bindings/pinctrl/mt65xx.h. bias-pull-up: oneOf: @@ -102,8 +103,8 @@ patternProperties: description: PUPD/R1/R0 pull up type. See MTK_PUPD_SET_R1R0_ defines in dt-bindings/pinctrl/mt65xx.h. - enum: [200, 201, 202, 203] - description: RSEL pull up type. See MTK_PULL_SET_RSEL_ - defines in dt-bindings/pinctrl/mt65xx.h. + description: RSEL pull up type. See MTK_PULL_SET_RSEL_ defines + in dt-bindings/pinctrl/mt65xx.h. bias-disable: true @@ -125,7 +126,7 @@ patternProperties: additionalProperties: false allOf: - - $ref: "pinctrl.yaml#" + - $ref: pinctrl.yaml# required: - compatible diff --git a/Documentation/devicetree/bindings/pinctrl/pinctrl-mt8195.yaml b/Documentation/devicetree/bindings/pinctrl/mediatek,mt8195-pinctrl.yaml index 66fe17e9e4d3..33cb71775db9 100644 --- a/Documentation/devicetree/bindings/pinctrl/pinctrl-mt8195.yaml +++ b/Documentation/devicetree/bindings/pinctrl/mediatek,mt8195-pinctrl.yaml @@ -1,16 +1,16 @@ # SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) %YAML 1.2 --- -$id: http://devicetree.org/schemas/pinctrl/pinctrl-mt8195.yaml# +$id: http://devicetree.org/schemas/pinctrl/mediatek,mt8195-pinctrl.yaml# $schema: http://devicetree.org/meta-schemas/core.yaml# -title: Mediatek MT8195 Pin Controller +title: MediaTek MT8195 Pin Controller maintainers: - Sean Wang <sean.wang@mediatek.com> -description: | - The Mediatek's Pin controller is used to control SoC pins. +description: + The MediaTek's MT8195 Pin controller is used to control SoC pins. properties: compatible: @@ -19,27 +19,27 @@ properties: gpio-controller: true '#gpio-cells': - description: | + description: Number of cells in GPIO specifier. Since the generic GPIO binding is used, - the amount of cells must be specified as 2. See the below - mentioned gpio binding representation for description of particular cells. + the amount of cells must be specified as 2. See the below mentioned gpio + binding representation for description of particular cells. const: 2 gpio-ranges: - description: gpio valid number range. + description: GPIO valid number range. maxItems: 1 gpio-line-names: true reg: - description: | - Physical address base for gpio base registers. There are 8 GPIO - physical address base in mt8195. + description: + Physical address base for GPIO base registers. There are 8 GPIO physical + address base in mt8195. maxItems: 8 reg-names: - description: | - Gpio base register names. + description: + GPIO base register names. maxItems: 8 interrupt-controller: true @@ -53,9 +53,9 @@ properties: mediatek,rsel-resistance-in-si-unit: type: boolean - description: | - Identifying i2c pins pull up/down type which is RSEL. It can support - RSEL define or si unit value(ohm) to set different resistance. + description: + Identifying i2c pins pull up/down type which is RSEL. It can support RSEL + define or si unit value(ohm) to set different resistance. # PIN CONFIGURATION NODES patternProperties: @@ -70,8 +70,8 @@ patternProperties: A pinctrl node should contain at least one subnodes representing the pinctrl groups available on the machine. Each subnode will list the pins it needs, and how they should be configured, with regard to muxer - configuration, pullups, drive strength, input enable/disable and - input schmitt. + configuration, pullups, drive strength, input enable/disable and input + schmitt. An example of using macro: pincontroller { /* GPIO0 set as multifunction GPIO0 */ @@ -87,15 +87,14 @@ patternProperties: } }; }; - $ref: "pinmux-node.yaml" + $ref: pinmux-node.yaml properties: pinmux: - description: | + description: Integer array, represents gpio pin number and mux setting. Supported pin number and mux varies for different SoCs, and are - defined as macros in dt-bindings/pinctrl/<soc>-pinfunc.h - directly. + defined as macros in dt-bindings/pinctrl/<soc>-pinfunc.h directly. drive-strength: enum: [2, 4, 6, 8, 10, 12, 14, 16] @@ -174,9 +173,9 @@ patternProperties: & "MTK_PULL_SET_RSEL_010" & "MTK_PULL_SET_RSEL_011" & "MTK_PULL_SET_RSEL_100" & "MTK_PULL_SET_RSEL_101" & "MTK_PULL_SET_RSEL_110" & "MTK_PULL_SET_RSEL_111" - define in mt8195. It can also support resistance value(ohm) - "1000" & "1500" & "2000" & "3000" & "4000" & "5000" & "10000" & - "75000" in mt8195. + define in mt8195. It can also support resistance value(ohm) "1000" + & "1500" & "2000" & "3000" & "4000" & "5000" & "10000" & "75000" + in mt8195. An example of using RSEL define: pincontroller { i2c0-pins { @@ -217,7 +216,7 @@ patternProperties: - pinmux allOf: - - $ref: "pinctrl.yaml#" + - $ref: pinctrl.yaml# required: - compatible diff --git a/Documentation/devicetree/bindings/pinctrl/mediatek,mt8365-pinctrl.yaml b/Documentation/devicetree/bindings/pinctrl/mediatek,mt8365-pinctrl.yaml index 4b96884a1afc..61b33b5416f5 100644 --- a/Documentation/devicetree/bindings/pinctrl/mediatek,mt8365-pinctrl.yaml +++ b/Documentation/devicetree/bindings/pinctrl/mediatek,mt8365-pinctrl.yaml @@ -4,13 +4,13 @@ $id: http://devicetree.org/schemas/pinctrl/mediatek,mt8365-pinctrl.yaml# $schema: http://devicetree.org/meta-schemas/core.yaml# -title: Mediatek MT8365 Pin Controller +title: MediaTek MT8365 Pin Controller maintainers: - Zhiyong Tao <zhiyong.tao@mediatek.com> - Bernhard Rosenkränzer <bero@baylibre.com> -description: | +description: The MediaTek's MT8365 Pin controller is used to control SoC pins. properties: @@ -26,17 +26,17 @@ properties: maxItems: 1 minItems: 1 maxItems: 2 - description: | + description: Should be phandles of the syscfg node. gpio-controller: true "#gpio-cells": const: 2 - description: | - Number of cells in GPIO specifier. Since the generic GPIO - binding is used, the amount of cells must be specified as 2. See the below - mentioned gpio binding representation for description of particular cells. + description: + Number of cells in GPIO specifier. Since the generic GPIO binding is used, + the amount of cells must be specified as 2. See the below mentioned gpio + binding representation for description of particular cells. interrupt-controller: true @@ -54,7 +54,7 @@ patternProperties: "pins$": type: object additionalProperties: false - description: | + description: A pinctrl node should contain at least one subnode representing the pinctrl groups available on the machine. Each subnode will list the pins it needs, and how they should be configured, with regard to muxer @@ -65,19 +65,42 @@ patternProperties: properties: pinmux: description: - integer array, represents gpio pin number and mux setting. + Integer array, represents gpio pin number and mux setting. Supported pin number and mux varies for different SoCs, and are defined as macros in <soc>-pinfunc.h directly. bias-disable: true bias-pull-up: + oneOf: + - type: boolean + - enum: [100, 101, 102, 103] + description: Pull up R1/R0 type define value. description: | - Besides generic pinconfig options, it can be used as the pull up - settings for 2 pull resistors, R0 and R1. User can configure those - special pins. + For pull up type is normal, it don't need add R1/R0 define. + For pull up type is R1/R0 type, it can add value to set different + resistance. Valid arguments are described as below: + 100: (R1, R0) = (0, 0) which means R1 disabled and R0 disabled. + 101: (R1, R0) = (0, 1) which means R1 disabled and R0 enabled. + 102: (R1, R0) = (1, 0) which means R1 enabled and R0 disabled. + 103: (R1, R0) = (1, 1) which means R1 enabled and R0 enabled. + + bias-pull-down: + oneOf: + - type: boolean + - enum: [100, 101, 102, 103] + description: Pull down R1/R0 type define value. + description: | + For pull down type is normal, it don't need add R1/R0 define. + For pull down type is R1/R0 type, it can add value to set + different resistance. Valid arguments are described as below: + 100: (R1, R0) = (0, 0) which means R1 disabled and R0 disabled. + 101: (R1, R0) = (0, 1) which means R1 disabled and R0 enabled. + 102: (R1, R0) = (1, 0) which means R1 enabled and R0 disabled. + 103: (R1, R0) = (1, 1) which means R1 enabled and R0 enabled. - bias-pull-down: true + drive-strength: + enum: [2, 4, 6, 8, 10, 12, 14, 16] input-enable: true @@ -91,8 +114,13 @@ patternProperties: input-schmitt-disable: true + drive-strength-microamp: + enum: [125, 250, 500, 1000] + mediatek,drive-strength-adv: + deprecated: true description: | + DEPRECATED: Please use drive-strength-microamp instead. Describe the specific driving setup property. For I2C pins, the existing generic driving setup can only support 2/4/6/8/10/12/14/16mA driving. But in specific driving setup, they @@ -118,9 +146,12 @@ patternProperties: enum: [0, 1, 2, 3, 4, 5, 6, 7] mediatek,pull-up-adv: + deprecated: true description: | + DEPRECATED: Please use bias-pull-up instead. Pull up setings for 2 pull resistors, R0 and R1. User can - configure those special pins. Valid arguments are described as below: + configure those special pins. Valid arguments are described as + below: 0: (R1, R0) = (0, 0) which means R1 disabled and R0 disabled. 1: (R1, R0) = (0, 1) which means R1 disabled and R0 enabled. 2: (R1, R0) = (1, 0) which means R1 enabled and R0 disabled. @@ -129,9 +160,12 @@ patternProperties: enum: [0, 1, 2, 3] mediatek,pull-down-adv: + deprecated: true description: | + DEPRECATED: Please use bias-pull-down instead. Pull down settings for 2 pull resistors, R0 and R1. User can - configure those special pins. Valid arguments are described as below: + configure those special pins. Valid arguments are described as + below: 0: (R1, R0) = (0, 0) which means R1 disabled and R0 disabled. 1: (R1, R0) = (0, 1) which means R1 disabled and R0 enabled. 2: (R1, R0) = (1, 0) which means R1 enabled and R0 disabled. @@ -140,14 +174,14 @@ patternProperties: enum: [0, 1, 2, 3] mediatek,tdsel: - description: | + description: An integer describing the steps for output level shifter duty cycle when asserted (high pulse width adjustment). Valid arguments are from 0 to 15. $ref: /schemas/types.yaml#/definitions/uint32 mediatek,rdsel: - description: | + description: An integer describing the steps for input level shifter duty cycle when asserted (high pulse width adjustment). Valid arguments are from 0 to 63. @@ -189,7 +223,6 @@ examples: pins { pinmux = <MT8365_PIN_59_SDA1__FUNC_SDA1_0>, <MT8365_PIN_60_SCL1__FUNC_SCL1_0>; mediatek,pull-up-adv = <3>; - mediatek,drive-strength-adv = <00>; bias-pull-up; }; }; diff --git a/Documentation/devicetree/bindings/pinctrl/meson,pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/meson,pinctrl.txt deleted file mode 100644 index 8146193bd8ac..000000000000 --- a/Documentation/devicetree/bindings/pinctrl/meson,pinctrl.txt +++ /dev/null @@ -1,94 +0,0 @@ -== Amlogic Meson pinmux controller == - -Required properties for the root node: - - compatible: one of "amlogic,meson8-cbus-pinctrl" - "amlogic,meson8b-cbus-pinctrl" - "amlogic,meson8m2-cbus-pinctrl" - "amlogic,meson8-aobus-pinctrl" - "amlogic,meson8b-aobus-pinctrl" - "amlogic,meson8m2-aobus-pinctrl" - "amlogic,meson-gxbb-periphs-pinctrl" - "amlogic,meson-gxbb-aobus-pinctrl" - "amlogic,meson-gxl-periphs-pinctrl" - "amlogic,meson-gxl-aobus-pinctrl" - "amlogic,meson-axg-periphs-pinctrl" - "amlogic,meson-axg-aobus-pinctrl" - "amlogic,meson-g12a-periphs-pinctrl" - "amlogic,meson-g12a-aobus-pinctrl" - "amlogic,meson-a1-periphs-pinctrl" - "amlogic,meson-s4-periphs-pinctrl" - - reg: address and size of registers controlling irq functionality - -=== GPIO sub-nodes === - -The GPIO bank for the controller is represented as a sub-node and it acts as a -GPIO controller. - -Required properties for sub-nodes are: - - reg: should contain a list of address and size, one tuple for each entry - in reg-names. - - reg-names: an array of strings describing the "reg" entries. - Must contain "mux" and "gpio". - May contain "pull", "pull-enable" and "ds" when appropriate. - - gpio-controller: identifies the node as a gpio controller - - #gpio-cells: must be 2 - -=== Other sub-nodes === - -Child nodes without the "gpio-controller" represent some desired -configuration for a pin or a group. Those nodes can be pinmux nodes or -configuration nodes. - -Required properties for pinmux nodes are: - - groups: a list of pinmux groups. The list of all available groups - depends on the SoC and can be found in driver sources. - - function: the name of a function to activate for the specified set - of groups. The list of all available functions depends on the SoC - and can be found in driver sources. - -Required properties for configuration nodes: - - pins: a list of pin names - -Configuration nodes support the following generic properties, as -described in file pinctrl-bindings.txt: - - "bias-disable" - - "bias-pull-up" - - "bias-pull-down" - - "output-enable" - - "output-disable" - - "output-low" - - "output-high" - -Optional properties : - - drive-strength-microamp: Drive strength for the specified pins in uA. - This property is only valid for G12A and newer. - -=== Example === - - pinctrl: pinctrl@c1109880 { - compatible = "amlogic,meson8-cbus-pinctrl"; - reg = <0xc1109880 0x10>; - #address-cells = <1>; - #size-cells = <1>; - ranges; - - gpio: banks@c11080b0 { - reg = <0xc11080b0 0x28>, - <0xc11080e8 0x18>, - <0xc1108120 0x18>, - <0xc1108030 0x30>; - reg-names = "mux", "pull", "pull-enable", "gpio"; - gpio-controller; - #gpio-cells = <2>; - }; - - nand { - mux { - groups = "nand_io", "nand_io_ce0", "nand_io_ce1", - "nand_io_rb0", "nand_ale", "nand_cle", - "nand_wen_clk", "nand_ren_clk", "nand_dqs", - "nand_ce2", "nand_ce3"; - function = "nand"; - }; - }; - }; diff --git a/Documentation/devicetree/bindings/pinctrl/mscc,ocelot-pinctrl.yaml b/Documentation/devicetree/bindings/pinctrl/mscc,ocelot-pinctrl.yaml index 98d547c34ef3..dbb3e1bd58c1 100644 --- a/Documentation/devicetree/bindings/pinctrl/mscc,ocelot-pinctrl.yaml +++ b/Documentation/devicetree/bindings/pinctrl/mscc,ocelot-pinctrl.yaml @@ -54,8 +54,8 @@ patternProperties: '-pins$': type: object allOf: - - $ref: "pinmux-node.yaml" - - $ref: "pincfg-node.yaml" + - $ref: pinmux-node.yaml + - $ref: pincfg-node.yaml properties: function: true @@ -78,7 +78,7 @@ required: - gpio-ranges allOf: - - $ref: "pinctrl.yaml#" + - $ref: pinctrl.yaml# - if: properties: compatible: diff --git a/Documentation/devicetree/bindings/pinctrl/nxp,s32g2-siul2-pinctrl.yaml b/Documentation/devicetree/bindings/pinctrl/nxp,s32g2-siul2-pinctrl.yaml new file mode 100644 index 000000000000..d49aafd8c5f4 --- /dev/null +++ b/Documentation/devicetree/bindings/pinctrl/nxp,s32g2-siul2-pinctrl.yaml @@ -0,0 +1,123 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +# Copyright 2022 NXP +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/pinctrl/nxp,s32g2-siul2-pinctrl.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: NXP S32G2 pin controller + +maintainers: + - Ghennadi Procopciuc <Ghennadi.Procopciuc@oss.nxp.com> + - Chester Lin <clin@suse.com> + +description: | + S32G2 pinmux is implemented in SIUL2 (System Integration Unit Lite2), + whose memory map is split into two regions: + SIUL2_0 @ 0x4009c000 + SIUL2_1 @ 0x44010000 + + Every SIUL2 region has multiple register types, and here only MSCR and + IMCR registers need to be revealed for kernel to configure pinmux. + + Please note that some register indexes are reserved in S32G2, such as + MSCR102-MSCR111, MSCR123-MSCR143, IMCR84-IMCR118 and IMCR398-IMCR429. + +properties: + compatible: + enum: + - nxp,s32g2-siul2-pinctrl + + reg: + description: | + A list of MSCR/IMCR register regions to be reserved. + - MSCR (Multiplexed Signal Configuration Register) + An MSCR register can configure the associated pin as either a GPIO pin + or a function output pin depends on the selected signal source. + - IMCR (Input Multiplexed Signal Configuration Register) + An IMCR register can configure the associated pin as function input + pin depends on the selected signal source. + items: + - description: MSCR registers group 0 in SIUL2_0 + - description: MSCR registers group 1 in SIUL2_1 + - description: MSCR registers group 2 in SIUL2_1 + - description: IMCR registers group 0 in SIUL2_0 + - description: IMCR registers group 1 in SIUL2_1 + - description: IMCR registers group 2 in SIUL2_1 + +patternProperties: + '-pins$': + type: object + additionalProperties: false + + patternProperties: + '-grp[0-9]$': + type: object + allOf: + - $ref: pinmux-node.yaml# + - $ref: pincfg-node.yaml# + description: | + Pinctrl node's client devices specify pin muxes using subnodes, + which in turn use the standard properties below. + + properties: + bias-disable: true + bias-high-impedance: true + bias-pull-up: true + bias-pull-down: true + drive-open-drain: true + input-enable: true + output-enable: true + + pinmux: + description: | + An integer array for representing pinmux configurations of + a device. Each integer consists of a PIN_ID and a 4-bit + selected signal source(SSS) as IOMUX setting, which is + calculated as: pinmux = (PIN_ID << 4 | SSS) + + slew-rate: + description: Supported slew rate based on Fmax values (MHz) + enum: [83, 133, 150, 166, 208] + + additionalProperties: false + +required: + - compatible + - reg + +additionalProperties: false + +examples: + - | + pinctrl@4009c240 { + compatible = "nxp,s32g2-siul2-pinctrl"; + + /* MSCR0-MSCR101 registers on siul2_0 */ + reg = <0x4009c240 0x198>, + /* MSCR112-MSCR122 registers on siul2_1 */ + <0x44010400 0x2c>, + /* MSCR144-MSCR190 registers on siul2_1 */ + <0x44010480 0xbc>, + /* IMCR0-IMCR83 registers on siul2_0 */ + <0x4009ca40 0x150>, + /* IMCR119-IMCR397 registers on siul2_1 */ + <0x44010c1c 0x45c>, + /* IMCR430-IMCR495 registers on siul2_1 */ + <0x440110f8 0x108>; + + llce-can0-pins { + llce-can0-grp0 { + pinmux = <0x2b0>; + input-enable; + slew-rate = <208>; + }; + + llce-can0-grp1 { + pinmux = <0x2c2>; + output-enable; + slew-rate = <208>; + }; + }; + }; +... diff --git a/Documentation/devicetree/bindings/pinctrl/qcom,ipq5332-tlmm.yaml b/Documentation/devicetree/bindings/pinctrl/qcom,ipq5332-tlmm.yaml index 300747252a7b..3d3086ae1ba6 100644 --- a/Documentation/devicetree/bindings/pinctrl/qcom,ipq5332-tlmm.yaml +++ b/Documentation/devicetree/bindings/pinctrl/qcom,ipq5332-tlmm.yaml @@ -56,6 +56,7 @@ $defs: Pinctrl node's client devices use subnodes for desired pin configuration. Client device subnodes use below standard properties. $ref: qcom,tlmm-common.yaml#/$defs/qcom-tlmm-state + unevaluatedProperties: false properties: pins: @@ -92,19 +93,9 @@ $defs: rx1, sdc_data, sdc_clk, sdc_cmd, tsens_max, wci_txd, wci_rxd, wsi_clk, wsi_clk3, wsi_data, wsi_data3, wsis_reset, xfem ] - bias-pull-down: true - bias-pull-up: true - bias-disable: true - drive-strength: true - input-enable: true - output-high: true - output-low: true - required: - pins - additionalProperties: false - required: - compatible - reg diff --git a/Documentation/devicetree/bindings/pinctrl/qcom,ipq6018-pinctrl.yaml b/Documentation/devicetree/bindings/pinctrl/qcom,ipq6018-pinctrl.yaml index 28f1b6a07b70..7c3e5e043f07 100644 --- a/Documentation/devicetree/bindings/pinctrl/qcom,ipq6018-pinctrl.yaml +++ b/Documentation/devicetree/bindings/pinctrl/qcom,ipq6018-pinctrl.yaml @@ -43,6 +43,7 @@ $defs: Pinctrl node's client devices use subnodes for desired pin configuration. Client device subnodes use below standard properties. $ref: qcom,tlmm-common.yaml#/$defs/qcom-tlmm-state + unevaluatedProperties: false properties: pins: @@ -89,18 +90,9 @@ $defs: sd_write, sec_mi2s, smb_int, ssbi_wtr0, ssbi_wtr1, uim1, uim2, uim3, uim_batt, wcss_bt, wcss_fm, wcss_wlan, webcam1_rst ] - bias-pull-down: true - bias-pull-up: true - bias-disable: true - drive-strength: true - output-high: true - output-low: true - required: - pins - additionalProperties: false - allOf: - $ref: /schemas/pinctrl/qcom,tlmm-common.yaml# diff --git a/Documentation/devicetree/bindings/pinctrl/qcom,ipq8074-pinctrl.yaml b/Documentation/devicetree/bindings/pinctrl/qcom,ipq8074-pinctrl.yaml index 3137db927fc0..e053fbd588b5 100644 --- a/Documentation/devicetree/bindings/pinctrl/qcom,ipq8074-pinctrl.yaml +++ b/Documentation/devicetree/bindings/pinctrl/qcom,ipq8074-pinctrl.yaml @@ -53,6 +53,7 @@ $defs: Pinctrl node's client devices use subnodes for desired pin configuration. Client device subnodes use below standard properties. $ref: qcom,tlmm-common.yaml#/$defs/qcom-tlmm-state + unevaluatedProperties: false properties: pins: @@ -92,19 +93,9 @@ $defs: qdss_tracedata_b, qpic, rx0, rx1, rx2, sd_card, sd_write, tsens_max, wci2a, wci2b, wci2c, wci2d ] - bias-pull-down: true - bias-pull-up: true - bias-disable: true - drive-strength: true - input-enable: true - output-high: true - output-low: true - required: - pins - additionalProperties: false - allOf: - $ref: /schemas/pinctrl/qcom,tlmm-common.yaml# diff --git a/Documentation/devicetree/bindings/pinctrl/qcom,ipq9574-tlmm.yaml b/Documentation/devicetree/bindings/pinctrl/qcom,ipq9574-tlmm.yaml new file mode 100644 index 000000000000..673713debac2 --- /dev/null +++ b/Documentation/devicetree/bindings/pinctrl/qcom,ipq9574-tlmm.yaml @@ -0,0 +1,130 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/pinctrl/qcom,ipq9574-tlmm.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Qualcomm Technologies, Inc. IPQ9574 TLMM block + +maintainers: + - Bjorn Andersson <andersson@kernel.org> + - Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org> + +description: + Top Level Mode Multiplexer pin controller in Qualcomm IPQ9574 SoC. + +properties: + compatible: + const: qcom,ipq9574-tlmm + + reg: + maxItems: 1 + + interrupts: + maxItems: 1 + + interrupt-controller: true + "#interrupt-cells": true + gpio-controller: true + "#gpio-cells": true + gpio-ranges: true + wakeup-parent: true + + gpio-reserved-ranges: + minItems: 1 + maxItems: 33 + + gpio-line-names: + maxItems: 65 + +patternProperties: + "-state$": + oneOf: + - $ref: "#/$defs/qcom-ipq9574-tlmm-state" + - patternProperties: + "-pins$": + $ref: "#/$defs/qcom-ipq9574-tlmm-state" + additionalProperties: false + +$defs: + qcom-ipq9574-tlmm-state: + type: object + description: + Pinctrl node's client devices use subnodes for desired pin configuration. + Client device subnodes use below standard properties. + $ref: qcom,tlmm-common.yaml#/$defs/qcom-tlmm-state + + properties: + pins: + description: + List of gpio pins affected by the properties specified in this + subnode. + items: + pattern: "^gpio([0-9]|[1-5][0-9]|6[0-4])$" + minItems: 1 + maxItems: 8 + + function: + description: + Specify the alternative function to be configured for the specified + pins. + + enum: [ atest_char, atest_char0, atest_char1, atest_char2, atest_char3, + audio_pdm0, audio_pdm1, audio_pri, audio_sec, blsp0_spi, blsp0_uart, + blsp1_i2c, blsp1_spi, blsp1_uart, blsp2_i2c, blsp2_spi, + blsp2_uart, blsp3_i2c, blsp3_spi, blsp3_uart, blsp4_i2c, + blsp4_spi, blsp4_uart, blsp5_i2c, blsp5_uart, cri_trng0, + cri_trng1, cri_trng2, cri_trng3, cxc0, cxc1, dbg_out, dwc_ddrphy, + gcc_plltest, gcc_tlmm, gpio, mac, mdc, mdio, pcie0_clk, pcie0_wake, + pcie1_clk, pcie1_wake, pcie2_clk, pcie2_wake, pcie3_clk, pcie3_wake, + prng_rosc0, prng_rosc1, prng_rosc2, prng_rosc3, pta, pwm, + qdss_cti_trig_in_a0, qdss_cti_trig_in_a1, qdss_cti_trig_in_b0, + qdss_cti_trig_in_b1, qdss_cti_trig_out_a0, qdss_cti_trig_out_a1, + qdss_cti_trig_out_b0, qdss_cti_trig_out_b1, qdss_traceclk_a, + qdss_traceclk_b, qdss_tracectl_a, qdss_tracectl_b, qdss_tracedata_a, + qdss_tracedata_b, qspi_clk, qspi_cs, qspi_data, + rx0, rx1, sdc_clk, sdc_cmd, sdc_data, sdc_rclk, tsens_max, + wci20, wci21, wsa_swrm ] + + bias-pull-down: true + bias-pull-up: true + bias-disable: true + drive-strength: true + input-enable: true + output-high: true + output-low: true + + required: + - pins + + additionalProperties: false + +allOf: + - $ref: /schemas/pinctrl/qcom,tlmm-common.yaml# + +required: + - compatible + - reg + +additionalProperties: false + +examples: + - | + #include <dt-bindings/interrupt-controller/arm-gic.h> + tlmm: pinctrl@1000000 { + compatible = "qcom,ipq9574-tlmm"; + reg = <0x01000000 0x300000>; + interrupts = <GIC_SPI 208 IRQ_TYPE_LEVEL_HIGH>; + gpio-controller; + #gpio-cells = <2>; + interrupt-controller; + #interrupt-cells = <2>; + gpio-ranges = <&tlmm 0 0 65>; + + uart2-state { + pins = "gpio34", "gpio35"; + function = "blsp2_uart"; + drive-strength = <8>; + bias-pull-down; + }; + }; diff --git a/Documentation/devicetree/bindings/pinctrl/qcom,mdm9607-tlmm.yaml b/Documentation/devicetree/bindings/pinctrl/qcom,mdm9607-tlmm.yaml index 96b598bf9a76..2aedb7e7bc8b 100644 --- a/Documentation/devicetree/bindings/pinctrl/qcom,mdm9607-tlmm.yaml +++ b/Documentation/devicetree/bindings/pinctrl/qcom,mdm9607-tlmm.yaml @@ -54,6 +54,7 @@ $defs: Pinctrl node's client devices use subnodes for desired pin configuration. Client device subnodes use below standard properties. $ref: qcom,tlmm-common.yaml#/$defs/qcom-tlmm-state + unevaluatedProperties: false properties: pins: @@ -105,19 +106,9 @@ $defs: uim1_clk, uim1_data, uim1_present, uim1_reset, uim2_clk, uim2_data, uim2_present, uim2_reset, uim_batt, wlan_en1, ] - bias-disable: true - bias-pull-down: true - bias-pull-up: true - drive-strength: true - input-enable: true - output-high: true - output-low: true - required: - pins - additionalProperties: false - examples: - | #include <dt-bindings/interrupt-controller/arm-gic.h> diff --git a/Documentation/devicetree/bindings/pinctrl/qcom,mdm9615-pinctrl.yaml b/Documentation/devicetree/bindings/pinctrl/qcom,mdm9615-pinctrl.yaml index c7c94d742ed2..5885aee95c98 100644 --- a/Documentation/devicetree/bindings/pinctrl/qcom,mdm9615-pinctrl.yaml +++ b/Documentation/devicetree/bindings/pinctrl/qcom,mdm9615-pinctrl.yaml @@ -51,6 +51,7 @@ $defs: Pinctrl node's client devices use subnodes for desired pin configuration. Client device subnodes use below standard properties. $ref: qcom,tlmm-common.yaml#/$defs/qcom-tlmm-state + unevaluatedProperties: false properties: pins: @@ -70,19 +71,9 @@ $defs: enum: [ gpio, gsbi2_i2c, gsbi3, gsbi4, gsbi5_i2c, gsbi5_uart, sdc2, ebi2_lcdc, ps_hold, prim_audio, sec_audio, cdc_mclk, ] - bias-disable: true - bias-pull-down: true - bias-pull-up: true - drive-strength: true - output-high: true - output-low: true - input-enable: true - required: - pins - additionalProperties: false - examples: - | #include <dt-bindings/interrupt-controller/arm-gic.h> diff --git a/Documentation/devicetree/bindings/pinctrl/qcom,msm8226-pinctrl.yaml b/Documentation/devicetree/bindings/pinctrl/qcom,msm8226-pinctrl.yaml index 6cb667fa8665..9efb76509580 100644 --- a/Documentation/devicetree/bindings/pinctrl/qcom,msm8226-pinctrl.yaml +++ b/Documentation/devicetree/bindings/pinctrl/qcom,msm8226-pinctrl.yaml @@ -48,6 +48,7 @@ $defs: Pinctrl node's client devices use subnodes for desired pin configuration. Client device subnodes use below standard properties. $ref: qcom,tlmm-common.yaml#/$defs/qcom-tlmm-state + unevaluatedProperties: false properties: pins: @@ -71,19 +72,9 @@ $defs: blsp_uart3, blsp_uart4, blsp_uart5, cam_mclk0, cam_mclk1, gp0_clk, gp1_clk, sdc3, wlan ] - bias-pull-down: true - bias-pull-up: true - bias-disable: true - drive-strength: true - input-enable: true - output-high: true - output-low: true - required: - pins - additionalProperties: false - allOf: - $ref: /schemas/pinctrl/qcom,tlmm-common.yaml# diff --git a/Documentation/devicetree/bindings/pinctrl/qcom,msm8660-pinctrl.yaml b/Documentation/devicetree/bindings/pinctrl/qcom,msm8660-pinctrl.yaml index 348d84c3cd21..a05971611780 100644 --- a/Documentation/devicetree/bindings/pinctrl/qcom,msm8660-pinctrl.yaml +++ b/Documentation/devicetree/bindings/pinctrl/qcom,msm8660-pinctrl.yaml @@ -53,6 +53,7 @@ $defs: Pinctrl node's client devices use subnodes for desired pin configuration. Client device subnodes use below standard properties. $ref: qcom,tlmm-common.yaml#/$defs/qcom-tlmm-state + unevaluatedProperties: false properties: pins: @@ -81,20 +82,9 @@ $defs: sdc5, tsif1, tsif2, usb_fs1, usb_fs1_oe_n, usb_fs2, usb_fs2_oe_n, vfe, vsens_alarm, ebi2, ebi2cs ] - - bias-pull-down: true - bias-pull-up: true - bias-disable: true - drive-strength: true - input-enable: true - output-high: true - output-low: true - required: - pins - additionalProperties: false - allOf: - $ref: /schemas/pinctrl/qcom,tlmm-common.yaml# diff --git a/Documentation/devicetree/bindings/pinctrl/qcom,msm8909-tlmm.yaml b/Documentation/devicetree/bindings/pinctrl/qcom,msm8909-tlmm.yaml index 85082adc1811..5095e86fe9a2 100644 --- a/Documentation/devicetree/bindings/pinctrl/qcom,msm8909-tlmm.yaml +++ b/Documentation/devicetree/bindings/pinctrl/qcom,msm8909-tlmm.yaml @@ -55,6 +55,7 @@ $defs: Pinctrl node's client devices use subnodes for desired pin configuration. Client device subnodes use below standard properties. $ref: qcom,tlmm-common.yaml#/$defs/qcom-tlmm-state + unevaluatedProperties: false properties: pins: @@ -104,19 +105,9 @@ $defs: uim3_clk, uim3_data, uim3_present, uim3_reset, uim_batt, wcss_bt, wcss_fm, wcss_wlan ] - bias-disable: true - bias-pull-down: true - bias-pull-up: true - drive-strength: true - input-enable: true - output-high: true - output-low: true - required: - pins - additionalProperties: false - examples: - | #include <dt-bindings/interrupt-controller/arm-gic.h> diff --git a/Documentation/devicetree/bindings/pinctrl/qcom,msm8916-pinctrl.yaml b/Documentation/devicetree/bindings/pinctrl/qcom,msm8916-pinctrl.yaml index 633c9e5ed49e..063d004967bb 100644 --- a/Documentation/devicetree/bindings/pinctrl/qcom,msm8916-pinctrl.yaml +++ b/Documentation/devicetree/bindings/pinctrl/qcom,msm8916-pinctrl.yaml @@ -53,6 +53,7 @@ $defs: Pinctrl node's client devices use subnodes for desired pin configuration. Client device subnodes use below standard properties. $ref: qcom,tlmm-common.yaml#/$defs/qcom-tlmm-state + unevaluatedProperties: false properties: pins: @@ -103,19 +104,9 @@ $defs: uim1, uim2, uim3, uim_batt, wcss_bt, wcss_fm, wcss_wlan, webcam1_rst ] - bias-pull-down: true - bias-pull-up: true - bias-disable: true - drive-strength: true - input-enable: true - output-high: true - output-low: true - required: - pins - additionalProperties: false - allOf: - $ref: /schemas/pinctrl/qcom,tlmm-common.yaml# diff --git a/Documentation/devicetree/bindings/pinctrl/qcom,msm8953-pinctrl.yaml b/Documentation/devicetree/bindings/pinctrl/qcom,msm8953-pinctrl.yaml index ce219827ccc8..798aac9e6e31 100644 --- a/Documentation/devicetree/bindings/pinctrl/qcom,msm8953-pinctrl.yaml +++ b/Documentation/devicetree/bindings/pinctrl/qcom,msm8953-pinctrl.yaml @@ -45,6 +45,7 @@ $defs: Pinctrl node's client devices use subnodes for desired pin configuration. Client device subnodes use below standard properties. $ref: qcom,tlmm-common.yaml#/$defs/qcom-tlmm-state + unevaluatedProperties: false properties: pins: @@ -106,18 +107,9 @@ $defs: uim_batt, us_emitter, us_euro, wcss_bt, wcss_fm, wcss_wlan, wcss_wlan0, wcss_wlan1, wcss_wlan2, wsa_en, wsa_io, wsa_irq ] - bias-pull-down: true - bias-pull-up: true - bias-disable: true - drive-strength: true - output-high: true - output-low: true - required: - pins - additionalProperties: false - allOf: - $ref: /schemas/pinctrl/qcom,tlmm-common.yaml# diff --git a/Documentation/devicetree/bindings/pinctrl/qcom,msm8960-pinctrl.yaml b/Documentation/devicetree/bindings/pinctrl/qcom,msm8960-pinctrl.yaml index cf386f644ccb..9172b50f7a98 100644 --- a/Documentation/devicetree/bindings/pinctrl/qcom,msm8960-pinctrl.yaml +++ b/Documentation/devicetree/bindings/pinctrl/qcom,msm8960-pinctrl.yaml @@ -53,6 +53,7 @@ $defs: Pinctrl node's client devices use subnodes for desired pin configuration. Client device subnodes use below standard properties. $ref: qcom,tlmm-common.yaml#/$defs/qcom-tlmm-state + unevaluatedProperties: false properties: pins: @@ -97,19 +98,9 @@ $defs: vfe_camif_timer7_a, vfe_camif_timer7_b, vfe_camif_timer7_c, wlan ] - bias-pull-down: true - bias-pull-up: true - bias-disable: true - drive-strength: true - input-enable: true - output-high: true - output-low: true - required: - pins - additionalProperties: false - allOf: - $ref: /schemas/pinctrl/qcom,tlmm-common.yaml# diff --git a/Documentation/devicetree/bindings/pinctrl/qcom,msm8974-pinctrl.yaml b/Documentation/devicetree/bindings/pinctrl/qcom,msm8974-pinctrl.yaml index afe4a80f0b79..8a3be65c51ed 100644 --- a/Documentation/devicetree/bindings/pinctrl/qcom,msm8974-pinctrl.yaml +++ b/Documentation/devicetree/bindings/pinctrl/qcom,msm8974-pinctrl.yaml @@ -53,6 +53,7 @@ $defs: Pinctrl node's client devices use subnodes for desired pin configuration. Client device subnodes use below standard properties. $ref: qcom,tlmm-common.yaml#/$defs/qcom-tlmm-state + unevaluatedProperties: false properties: pins: @@ -93,14 +94,6 @@ $defs: tsif1, tsif2, hsic, grfc, audio_ref_clk, qua_mi2s, pri_mi2s, spkr_mi2s, ter_mi2s, sec_mi2s, bt, fm, wlan, slimbus, hsic_ctl ] - bias-pull-down: true - bias-pull-up: true - bias-disable: true - drive-strength: true - input-enable: true - output-high: true - output-low: true - required: - pins @@ -124,8 +117,6 @@ $defs: output-high: false output-low: false - additionalProperties: false - allOf: - $ref: /schemas/pinctrl/qcom,tlmm-common.yaml# diff --git a/Documentation/devicetree/bindings/pinctrl/qcom,msm8976-pinctrl.yaml b/Documentation/devicetree/bindings/pinctrl/qcom,msm8976-pinctrl.yaml index 5dfcc3eadbb0..ca95de0b87a6 100644 --- a/Documentation/devicetree/bindings/pinctrl/qcom,msm8976-pinctrl.yaml +++ b/Documentation/devicetree/bindings/pinctrl/qcom,msm8976-pinctrl.yaml @@ -53,6 +53,7 @@ $defs: Desired pin configuration for a device or its specific state (like sleep or active). $ref: qcom,tlmm-common.yaml#/$defs/qcom-tlmm-state + unevaluatedProperties: false properties: pins: @@ -93,19 +94,9 @@ $defs: wsa_irq, blsp_i2c8, pa_indicator, modem_tsync, ssbi_wtr1, gsm1_tx, gsm0_tx, sdcard_det, sec_mi2s, ss_switch ] - bias-pull-down: true - bias-pull-up: true - bias-disable: true - drive-strength: true - input-enable: true - output-high: true - output-low: true - required: - pins - additionalProperties: false - allOf: - $ref: /schemas/pinctrl/qcom,tlmm-common.yaml# diff --git a/Documentation/devicetree/bindings/pinctrl/qcom,msm8994-pinctrl.yaml b/Documentation/devicetree/bindings/pinctrl/qcom,msm8994-pinctrl.yaml index 0c4936fc35ef..41525ecfa8e3 100644 --- a/Documentation/devicetree/bindings/pinctrl/qcom,msm8994-pinctrl.yaml +++ b/Documentation/devicetree/bindings/pinctrl/qcom,msm8994-pinctrl.yaml @@ -55,6 +55,7 @@ $defs: Pinctrl node's client devices use subnodes for desired pin configuration. Client device subnodes use below standard properties. $ref: qcom,tlmm-common.yaml#/$defs/qcom-tlmm-state + unevaluatedProperties: false properties: pins: @@ -103,19 +104,9 @@ $defs: pri_mi2s, sdc4, sec_mi2s, slimbus, spkr_i2s, ter_mi2s, tsif1, tsif2, uim_batt_alarm, uim1, uim2, uim3, uim4 ] - bias-pull-down: true - bias-pull-up: true - bias-disable: true - drive-strength: true - input-enable: true - output-high: true - output-low: true - required: - pins - additionalProperties: false - allOf: - $ref: /schemas/pinctrl/qcom,tlmm-common.yaml# diff --git a/Documentation/devicetree/bindings/pinctrl/qcom,msm8996-pinctrl.yaml b/Documentation/devicetree/bindings/pinctrl/qcom,msm8996-pinctrl.yaml index 047b4584e3c0..59d406b60957 100644 --- a/Documentation/devicetree/bindings/pinctrl/qcom,msm8996-pinctrl.yaml +++ b/Documentation/devicetree/bindings/pinctrl/qcom,msm8996-pinctrl.yaml @@ -53,6 +53,7 @@ $defs: Pinctrl node's client devices use subnodes for desired pin configuration. Client device subnodes use below standard properties. $ref: qcom,tlmm-common.yaml#/$defs/qcom-tlmm-state + unevaluatedProperties: false properties: pins: @@ -122,19 +123,9 @@ $defs: modem_tsync, nav_dr, nav_pps, pci_e1, gsm_tx, qspi_cs, ssbi2, ssbi1, mss_lte, qspi_clk, qspi0, qspi1, qspi2, qspi3 ] - bias-pull-down: true - bias-pull-up: true - bias-disable: true - drive-strength: true - input-enable: true - output-high: true - output-low: true - required: - pins - additionalProperties: false - allOf: - $ref: /schemas/pinctrl/qcom,tlmm-common.yaml# diff --git a/Documentation/devicetree/bindings/pinctrl/qcom,msm8998-pinctrl.yaml b/Documentation/devicetree/bindings/pinctrl/qcom,msm8998-pinctrl.yaml index c07ee9868046..bd6d7caf499a 100644 --- a/Documentation/devicetree/bindings/pinctrl/qcom,msm8998-pinctrl.yaml +++ b/Documentation/devicetree/bindings/pinctrl/qcom,msm8998-pinctrl.yaml @@ -53,6 +53,7 @@ $defs: Pinctrl node's client devices use subnodes for desired pin configuration. Client device subnodes use below standard properties. $ref: qcom,tlmm-common.yaml#/$defs/qcom-tlmm-state + unevaluatedProperties: false properties: pins: @@ -107,19 +108,9 @@ $defs: vsense_clkout, vsense_data0, vsense_data1, vsense_mode, wlan1_adc0, wlan1_adc1, wlan2_adc0, wlan2_adc1 ] - bias-pull-down: true - bias-pull-up: true - bias-disable: true - drive-strength: true - input-enable: true - output-high: true - output-low: true - required: - pins - additionalProperties: false - allOf: - $ref: /schemas/pinctrl/qcom,tlmm-common.yaml# diff --git a/Documentation/devicetree/bindings/pinctrl/qcom,pmic-gpio.yaml b/Documentation/devicetree/bindings/pinctrl/qcom,pmic-gpio.yaml index db505fdeac86..eaadd5a9a445 100644 --- a/Documentation/devicetree/bindings/pinctrl/qcom,pmic-gpio.yaml +++ b/Documentation/devicetree/bindings/pinctrl/qcom,pmic-gpio.yaml @@ -52,12 +52,14 @@ properties: - qcom,pm8994-gpio - qcom,pm8998-gpio - qcom,pma8084-gpio + - qcom,pmi632-gpio - qcom,pmi8950-gpio - qcom,pmi8994-gpio - qcom,pmi8998-gpio - qcom,pmk8350-gpio - qcom,pmk8550-gpio - qcom,pmm8155au-gpio + - qcom,pmm8654au-gpio - qcom,pmp8074-gpio - qcom,pmr735a-gpio - qcom,pmr735b-gpio @@ -173,6 +175,7 @@ allOf: - qcom,pm8350b-gpio - qcom,pm8550ve-gpio - qcom,pm8950-gpio + - qcom,pmi632-gpio then: properties: gpio-line-names: @@ -395,8 +398,8 @@ $defs: qcom-pmic-gpio-state: type: object allOf: - - $ref: "pinmux-node.yaml" - - $ref: "pincfg-node.yaml" + - $ref: pinmux-node.yaml + - $ref: pincfg-node.yaml properties: pins: description: @@ -434,11 +437,13 @@ $defs: - gpio1-gpio22 for pm8994 - gpio1-gpio26 for pm8998 - gpio1-gpio22 for pma8084 + - gpio1-gpio8 for pmi632 - gpio1-gpio2 for pmi8950 - gpio1-gpio10 for pmi8994 - gpio1-gpio4 for pmk8350 - gpio1-gpio6 for pmk8550 - gpio1-gpio10 for pmm8155au + - gpio1-gpio12 for pmm8654au - gpio1-gpio12 for pmp8074 (holes on gpio1 and gpio12) - gpio1-gpio4 for pmr735a - gpio1-gpio4 for pmr735b diff --git a/Documentation/devicetree/bindings/pinctrl/qcom,pmic-mpp.yaml b/Documentation/devicetree/bindings/pinctrl/qcom,pmic-mpp.yaml index 9412b9362328..c91d3e3a094b 100644 --- a/Documentation/devicetree/bindings/pinctrl/qcom,pmic-mpp.yaml +++ b/Documentation/devicetree/bindings/pinctrl/qcom,pmic-mpp.yaml @@ -82,8 +82,8 @@ $defs: qcom-pmic-mpp-state: type: object allOf: - - $ref: "pinmux-node.yaml" - - $ref: "pincfg-node.yaml" + - $ref: pinmux-node.yaml + - $ref: pincfg-node.yaml properties: pins: description: diff --git a/Documentation/devicetree/bindings/pinctrl/qcom,qcm2290-tlmm.yaml b/Documentation/devicetree/bindings/pinctrl/qcom,qcm2290-tlmm.yaml index 6271fd15e0b6..032763649336 100644 --- a/Documentation/devicetree/bindings/pinctrl/qcom,qcm2290-tlmm.yaml +++ b/Documentation/devicetree/bindings/pinctrl/qcom,qcm2290-tlmm.yaml @@ -85,6 +85,7 @@ $defs: bias-pull-up: true bias-disable: true drive-strength: true + input-enable: true output-high: true output-low: true diff --git a/Documentation/devicetree/bindings/pinctrl/qcom,qcs404-pinctrl.yaml b/Documentation/devicetree/bindings/pinctrl/qcom,qcs404-pinctrl.yaml index 20bc967a17b5..b1b9cd319e50 100644 --- a/Documentation/devicetree/bindings/pinctrl/qcom,qcs404-pinctrl.yaml +++ b/Documentation/devicetree/bindings/pinctrl/qcom,qcs404-pinctrl.yaml @@ -59,6 +59,7 @@ $defs: Pinctrl node's client devices use subnodes for desired pin configuration. Client device subnodes use below standard properties. $ref: qcom,tlmm-common.yaml#/$defs/qcom-tlmm-state + unevaluatedProperties: false properties: pins: @@ -119,19 +120,9 @@ $defs: spdifrx_opt, spi_lcd, spkr_dac0, wlan1_adc0, wlan1_adc1, wlan2_adc0, wlan2_adc1, wsa_en ] - bias-pull-down: true - bias-pull-up: true - bias-disable: true - drive-strength: true - input-enable: true - output-high: true - output-low: true - required: - pins - additionalProperties: false - allOf: - $ref: /schemas/pinctrl/qcom,tlmm-common.yaml# diff --git a/Documentation/devicetree/bindings/pinctrl/qcom,qdu1000-tlmm.yaml b/Documentation/devicetree/bindings/pinctrl/qcom,qdu1000-tlmm.yaml index 7e5fb9a6e7d3..237cac4f6ce1 100644 --- a/Documentation/devicetree/bindings/pinctrl/qcom,qdu1000-tlmm.yaml +++ b/Documentation/devicetree/bindings/pinctrl/qcom,qdu1000-tlmm.yaml @@ -55,6 +55,7 @@ $defs: Pinctrl node's client devices use subnodes for desired pin configuration. Client device subnodes use below standard properties. $ref: qcom,tlmm-common.yaml#/$defs/qcom-tlmm-state + unevaluatedProperties: false properties: pins: @@ -93,19 +94,9 @@ $defs: usb2phy_ac, usb_con_det, usb_dfp_en, usb_phy, vfr_0, vfr_1, vsense_trigger ] - bias-disable: true - bias-pull-down: true - bias-pull-up: true - drive-strength: true - input-enable: true - output-high: true - output-low: true - required: - pins - additionalProperties: false - required: - compatible - reg diff --git a/Documentation/devicetree/bindings/pinctrl/qcom,sa8775p-tlmm.yaml b/Documentation/devicetree/bindings/pinctrl/qcom,sa8775p-tlmm.yaml index 70d9106ad83d..e608a4f1bcae 100644 --- a/Documentation/devicetree/bindings/pinctrl/qcom,sa8775p-tlmm.yaml +++ b/Documentation/devicetree/bindings/pinctrl/qcom,sa8775p-tlmm.yaml @@ -58,6 +58,7 @@ $defs: Pinctrl node's client devices use subnodes for desired pin configuration. Client device subnodes use below standard properties. $ref: qcom,tlmm-common.yaml#/$defs/qcom-tlmm-state + unevaluatedProperties: false properties: pins: @@ -103,19 +104,9 @@ $defs: tgu_ch2, tgu_ch3, tgu_ch4, tgu_ch5, tsense_pwm1, tsense_pwm2, tsense_pwm3, tsense_pwm4, usb2phy_ac, vsense_trigger ] - bias-disable: true - bias-pull-down: true - bias-pull-up: true - drive-strength: true - input-enable: true - output-high: true - output-low: true - required: - pins - additionalProperties: false - examples: - | #include <dt-bindings/interrupt-controller/arm-gic.h> diff --git a/Documentation/devicetree/bindings/pinctrl/qcom,sc7180-pinctrl.yaml b/Documentation/devicetree/bindings/pinctrl/qcom,sc7180-pinctrl.yaml index f33792a1af6c..573e459b1c44 100644 --- a/Documentation/devicetree/bindings/pinctrl/qcom,sc7180-pinctrl.yaml +++ b/Documentation/devicetree/bindings/pinctrl/qcom,sc7180-pinctrl.yaml @@ -59,6 +59,7 @@ $defs: Pinctrl node's client devices use subnodes for desired pin configuration. Client device subnodes use below standard properties. $ref: qcom,tlmm-common.yaml#/$defs/qcom-tlmm-state + unevaluatedProperties: false properties: pins: @@ -100,19 +101,9 @@ $defs: _V_GPIO, _V_PPS_IN, _V_PPS_OUT, vsense_trigger, wlan1_adc0, wlan1_adc1, wlan2_adc0, wlan2_adc1 ] - bias-pull-down: true - bias-pull-up: true - bias-disable: true - drive-strength: true - input-enable: true - output-high: true - output-low: true - required: - pins - additionalProperties: false - allOf: - $ref: /schemas/pinctrl/qcom,tlmm-common.yaml# diff --git a/Documentation/devicetree/bindings/pinctrl/qcom,sc7280-lpass-lpi-pinctrl.yaml b/Documentation/devicetree/bindings/pinctrl/qcom,sc7280-lpass-lpi-pinctrl.yaml index e51feb4c0700..fa51fa9536f7 100644 --- a/Documentation/devicetree/bindings/pinctrl/qcom,sc7280-lpass-lpi-pinctrl.yaml +++ b/Documentation/devicetree/bindings/pinctrl/qcom,sc7280-lpass-lpi-pinctrl.yaml @@ -50,7 +50,7 @@ $defs: description: Pinctrl node's client devices use subnodes for desired pin configuration. Client device subnodes use below standard properties. - $ref: "/schemas/pinctrl/pincfg-node.yaml" + $ref: /schemas/pinctrl/pincfg-node.yaml properties: pins: diff --git a/Documentation/devicetree/bindings/pinctrl/qcom,sc7280-pinctrl.yaml b/Documentation/devicetree/bindings/pinctrl/qcom,sc7280-pinctrl.yaml index 36502173cb79..368d44ff5468 100644 --- a/Documentation/devicetree/bindings/pinctrl/qcom,sc7280-pinctrl.yaml +++ b/Documentation/devicetree/bindings/pinctrl/qcom,sc7280-pinctrl.yaml @@ -62,6 +62,7 @@ $defs: Pinctrl node's client devices use subnodes for desired pin configuration. Client device subnodes use below standard properties. $ref: qcom,tlmm-common.yaml#/$defs/qcom-tlmm-state + unevaluatedProperties: false properties: pins: @@ -110,20 +111,9 @@ $defs: uim1_clk, uim1_data, uim1_present, uim1_reset, usb2phy_ac, usb_phy, vfr_0, vfr_1, vsense_trigger ] - bias-pull-down: true - bias-pull-up: true - bias-bus-hold: true - bias-disable: true - drive-strength: true - input-enable: true - output-high: true - output-low: true - required: - pins - additionalProperties: false - allOf: - $ref: /schemas/pinctrl/qcom,tlmm-common.yaml# diff --git a/Documentation/devicetree/bindings/pinctrl/qcom,sc8180x-tlmm.yaml b/Documentation/devicetree/bindings/pinctrl/qcom,sc8180x-tlmm.yaml index 0ace55c9868e..b086a5184235 100644 --- a/Documentation/devicetree/bindings/pinctrl/qcom,sc8180x-tlmm.yaml +++ b/Documentation/devicetree/bindings/pinctrl/qcom,sc8180x-tlmm.yaml @@ -62,6 +62,7 @@ $defs: Pinctrl node's client devices use subnodes for desired pin configuration. Client device subnodes use below standard properties. $ref: qcom,tlmm-common.yaml#/$defs/qcom-tlmm-state + unevaluatedProperties: false properties: pins: @@ -102,19 +103,9 @@ $defs: usb0_phy, usb1_phy, usb2phy_ac, vfr_1, vsense_trigger, wlan1_adc, wlan2_adc, wmss_reset ] - bias-disable: true - bias-pull-down: true - bias-pull-up: true - drive-strength: true - input-enable: true - output-high: true - output-low: true - required: - pins - additionalProperties: false - examples: - | #include <dt-bindings/interrupt-controller/arm-gic.h> diff --git a/Documentation/devicetree/bindings/pinctrl/qcom,sc8280xp-lpass-lpi-pinctrl.yaml b/Documentation/devicetree/bindings/pinctrl/qcom,sc8280xp-lpass-lpi-pinctrl.yaml index 200b3b6ccd87..a9167dac9ab5 100644 --- a/Documentation/devicetree/bindings/pinctrl/qcom,sc8280xp-lpass-lpi-pinctrl.yaml +++ b/Documentation/devicetree/bindings/pinctrl/qcom,sc8280xp-lpass-lpi-pinctrl.yaml @@ -20,7 +20,7 @@ properties: reg: items: - description: LPASS LPI TLMM Control and Status registers - - description: LPASS LPI pins SLEW registers + - description: LPASS LPI MCC registers clocks: items: diff --git a/Documentation/devicetree/bindings/pinctrl/qcom,sc8280xp-tlmm.yaml b/Documentation/devicetree/bindings/pinctrl/qcom,sc8280xp-tlmm.yaml index 97b27d6835e9..4ae39fc7894a 100644 --- a/Documentation/devicetree/bindings/pinctrl/qcom,sc8280xp-tlmm.yaml +++ b/Documentation/devicetree/bindings/pinctrl/qcom,sc8280xp-tlmm.yaml @@ -104,6 +104,7 @@ $defs: usb1_phy, usb1_sbrx, usb1_sbtx, usb1_usb4, usb2phy_ac, vsense_trigger ] + bias-bus-hold: true bias-disable: true bias-pull-down: true bias-pull-up: true diff --git a/Documentation/devicetree/bindings/pinctrl/qcom,sdm630-pinctrl.yaml b/Documentation/devicetree/bindings/pinctrl/qcom,sdm630-pinctrl.yaml index ea6bd0b44f56..508e0633b253 100644 --- a/Documentation/devicetree/bindings/pinctrl/qcom,sdm630-pinctrl.yaml +++ b/Documentation/devicetree/bindings/pinctrl/qcom,sdm630-pinctrl.yaml @@ -65,6 +65,7 @@ $defs: Pinctrl node's client devices use subnodes for desired pin configuration. Client device subnodes use below standard properties. $ref: qcom,tlmm-common.yaml#/$defs/qcom-tlmm-state + unevaluatedProperties: false properties: pins: @@ -122,19 +123,9 @@ $defs: vsense_data0, vsense_data1, vsense_mode, wlan1_adc0, wlan1_adc1, wlan2_adc0, wlan2_adc1 ] - bias-disable: true - bias-pull-down: true - bias-pull-up: true - drive-strength: true - input-enable: true - output-high: true - output-low: true - required: - pins - additionalProperties: false - required: - compatible - reg diff --git a/Documentation/devicetree/bindings/pinctrl/qcom,sdm670-tlmm.yaml b/Documentation/devicetree/bindings/pinctrl/qcom,sdm670-tlmm.yaml index f586b3aa138e..84a15f77e710 100644 --- a/Documentation/devicetree/bindings/pinctrl/qcom,sdm670-tlmm.yaml +++ b/Documentation/devicetree/bindings/pinctrl/qcom,sdm670-tlmm.yaml @@ -58,6 +58,7 @@ $defs: Pinctrl node's client devices use subnodes for desired pin configuration. Client device subnodes use below standard properties. $ref: qcom,tlmm-common.yaml#/$defs/qcom-tlmm-state + unevaluatedProperties: false properties: pins: @@ -94,20 +95,9 @@ $defs: uim1_reset, uim2_clk, uim2_data, uim2_present, uim2_reset, uim_batt, usb_phy, vfr_1, vsense_trigger, wlan1_adc0, wlan1_adc1, wlan2_adc0, wlan2_adc1, wsa_clk, wsa_data, ] - - bias-disable: true - bias-pull-down: true - bias-pull-up: true - drive-strength: true - input-enable: true - output-high: true - output-low: true - required: - pins - additionalProperties: false - examples: - | #include <dt-bindings/interrupt-controller/arm-gic.h> diff --git a/Documentation/devicetree/bindings/pinctrl/qcom,sdm845-pinctrl.yaml b/Documentation/devicetree/bindings/pinctrl/qcom,sdm845-pinctrl.yaml index 23d7c030fec0..d301881ddfa8 100644 --- a/Documentation/devicetree/bindings/pinctrl/qcom,sdm845-pinctrl.yaml +++ b/Documentation/devicetree/bindings/pinctrl/qcom,sdm845-pinctrl.yaml @@ -61,6 +61,7 @@ $defs: Pinctrl node's client devices use subnodes for desired pin configuration. Client device subnodes use below standard properties. $ref: qcom,tlmm-common.yaml#/$defs/qcom-tlmm-state + unevaluatedProperties: false properties: pins: @@ -102,19 +103,9 @@ $defs: uim_batt, usb_phy, vfr_1, vsense_trigger, wlan1_adc0, wlan1_adc1, wlan2_adc0, wlan2_adc1] - bias-disable: true - bias-pull-down: true - bias-pull-up: true - drive-strength: true - input-enable: true - output-high: true - output-low: true - required: - pins - additionalProperties: false - required: - compatible - reg diff --git a/Documentation/devicetree/bindings/pinctrl/qcom,sdx55-pinctrl.yaml b/Documentation/devicetree/bindings/pinctrl/qcom,sdx55-pinctrl.yaml index a40175258495..67af99dd8f14 100644 --- a/Documentation/devicetree/bindings/pinctrl/qcom,sdx55-pinctrl.yaml +++ b/Documentation/devicetree/bindings/pinctrl/qcom,sdx55-pinctrl.yaml @@ -48,6 +48,7 @@ $defs: Pinctrl node's client devices use subnodes for desired pin configuration. Client device subnodes use below standard properties. $ref: qcom,tlmm-common.yaml#/$defs/qcom-tlmm-state + unevaluatedProperties: false properties: pins: @@ -91,18 +92,9 @@ $defs: uim1_present, uim1_reset, uim2_clk, uim2_data, uim2_present, uim2_reset, usb2phy_ac, vsense_trigger ] - bias-pull-down: true - bias-pull-up: true - bias-disable: true - drive-strength: true - output-high: true - output-low: true - required: - pins - additionalProperties: false - allOf: - $ref: /schemas/pinctrl/qcom,tlmm-common.yaml# diff --git a/Documentation/devicetree/bindings/pinctrl/qcom,sdx65-tlmm.yaml b/Documentation/devicetree/bindings/pinctrl/qcom,sdx65-tlmm.yaml index 89c5562583d1..2ef793ae4038 100644 --- a/Documentation/devicetree/bindings/pinctrl/qcom,sdx65-tlmm.yaml +++ b/Documentation/devicetree/bindings/pinctrl/qcom,sdx65-tlmm.yaml @@ -47,6 +47,7 @@ $defs: Pinctrl node's client devices use subnodes for desired pin configuration. Client device subnodes use below standard properties. $ref: qcom,tlmm-common.yaml#/$defs/qcom-tlmm-state + unevaluatedProperties: false properties: pins: @@ -111,18 +112,9 @@ $defs: qspi_cs, ssbi2, ssbi1, mss_lte, qspi_clk, qspi0, qspi1, qspi2, qspi3, gpio ] - bias-pull-down: true - bias-pull-up: true - bias-disable: true - drive-strength: true - output-high: true - output-low: true - required: - pins - additionalProperties: false - allOf: - $ref: /schemas/pinctrl/qcom,tlmm-common.yaml# diff --git a/Documentation/devicetree/bindings/pinctrl/qcom,sm6115-tlmm.yaml b/Documentation/devicetree/bindings/pinctrl/qcom,sm6115-tlmm.yaml index 29325483cd2b..871df54f69a2 100644 --- a/Documentation/devicetree/bindings/pinctrl/qcom,sm6115-tlmm.yaml +++ b/Documentation/devicetree/bindings/pinctrl/qcom,sm6115-tlmm.yaml @@ -53,6 +53,7 @@ $defs: Pinctrl node's client devices use subnodes for desired pin configuration. Client device subnodes use below standard properties. $ref: qcom,tlmm-common.yaml#/$defs/qcom-tlmm-state + unevaluatedProperties: false properties: pins: @@ -85,18 +86,9 @@ $defs: uim2_present, uim2_reset, usb_phy, vfr_1, vsense_trigger, wlan1_adc0, elan1_adc1 ] - bias-pull-down: true - bias-pull-up: true - bias-disable: true - drive-strength: true - output-high: true - output-low: true - required: - pins - additionalProperties: false - allOf: - $ref: /schemas/pinctrl/qcom,tlmm-common.yaml# diff --git a/Documentation/devicetree/bindings/pinctrl/qcom,sm6125-tlmm.yaml b/Documentation/devicetree/bindings/pinctrl/qcom,sm6125-tlmm.yaml index c9bc4893e8e8..8d77707b02b9 100644 --- a/Documentation/devicetree/bindings/pinctrl/qcom,sm6125-tlmm.yaml +++ b/Documentation/devicetree/bindings/pinctrl/qcom,sm6125-tlmm.yaml @@ -61,6 +61,7 @@ $defs: Pinctrl node's client devices use subnodes for desired pin configuration. Client device subnodes use below standard properties. $ref: qcom,tlmm-common.yaml#/$defs/qcom-tlmm-state + unevaluatedProperties: false properties: pins: @@ -101,19 +102,9 @@ $defs: wlan1_adc0, wlan1_adc1, wlan2_adc0, wlan2_adc1, wsa_clk, wsa_data ] - bias-disable: true - bias-pull-down: true - bias-pull-up: true - drive-strength: true - input-enable: true - output-high: true - output-low: true - required: - pins - additionalProperties: false - examples: - | #include <dt-bindings/interrupt-controller/arm-gic.h> diff --git a/Documentation/devicetree/bindings/pinctrl/qcom,sm6350-tlmm.yaml b/Documentation/devicetree/bindings/pinctrl/qcom,sm6350-tlmm.yaml index d95935fcc8b5..27af379cf791 100644 --- a/Documentation/devicetree/bindings/pinctrl/qcom,sm6350-tlmm.yaml +++ b/Documentation/devicetree/bindings/pinctrl/qcom,sm6350-tlmm.yaml @@ -63,6 +63,7 @@ $defs: Pinctrl node's client devices use subnodes for desired pin configuration. Client device subnodes use below standard properties. $ref: qcom,tlmm-common.yaml#/$defs/qcom-tlmm-state + unevaluatedProperties: false properties: pins: @@ -108,20 +109,9 @@ $defs: uim2_present, uim2_reset, usb_phy, vfr_1, vsense_trigger, wlan1_adc0, wlan1_adc1, wlan2_adc0, wlan2_adc1, ] - - bias-disable: true - bias-pull-down: true - bias-pull-up: true - drive-strength: true - input-enable: true - output-high: true - output-low: true - required: - pins - additionalProperties: false - examples: - | #include <dt-bindings/interrupt-controller/arm-gic.h> diff --git a/Documentation/devicetree/bindings/pinctrl/qcom,sm6375-tlmm.yaml b/Documentation/devicetree/bindings/pinctrl/qcom,sm6375-tlmm.yaml index 66cef48ed59b..6e02ba24825f 100644 --- a/Documentation/devicetree/bindings/pinctrl/qcom,sm6375-tlmm.yaml +++ b/Documentation/devicetree/bindings/pinctrl/qcom,sm6375-tlmm.yaml @@ -55,6 +55,7 @@ $defs: Pinctrl node's client devices use subnodes for desired pin configuration. Client device subnodes use below standard properties. $ref: qcom,tlmm-common.yaml#/$defs/qcom-tlmm-state + unevaluatedProperties: false properties: pins: @@ -109,20 +110,9 @@ $defs: usb_phy, vfr_1, vsense_trigger, wlan1_adc0, wlan1_adc1, wlan2_adc0, wlan2_adc1 ] - - bias-disable: true - bias-pull-down: true - bias-pull-up: true - drive-strength: true - input-enable: true - output-high: true - output-low: true - required: - pins - additionalProperties: false - examples: - | #include <dt-bindings/interrupt-controller/arm-gic.h> diff --git a/Documentation/devicetree/bindings/pinctrl/qcom,sm7150-tlmm.yaml b/Documentation/devicetree/bindings/pinctrl/qcom,sm7150-tlmm.yaml new file mode 100644 index 000000000000..a57d44efe5bd --- /dev/null +++ b/Documentation/devicetree/bindings/pinctrl/qcom,sm7150-tlmm.yaml @@ -0,0 +1,162 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/pinctrl/qcom,sm7150-tlmm.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Qualcomm SM7150 TLMM pin controller + +maintainers: + - Bjorn Andersson <andersson@kernel.org> + - Danila Tikhonov <danila@jiaxyga.com> + +description: + Top Level Mode Multiplexer pin controller in Qualcomm SM7150 SoC. + +allOf: + - $ref: /schemas/pinctrl/qcom,tlmm-common.yaml# + +properties: + compatible: + const: qcom,sm7150-tlmm + + reg: + maxItems: 3 + + reg-names: + items: + - const: west + - const: north + - const: south + + interrupts: + maxItems: 1 + + interrupt-controller: true + "#interrupt-cells": true + gpio-controller: true + "#gpio-cells": true + gpio-ranges: true + wakeup-parent: true + + gpio-reserved-ranges: + minItems: 1 + maxItems: 60 + + gpio-line-names: + maxItems: 119 + +patternProperties: + "-state$": + oneOf: + - $ref: "#/$defs/qcom-sm7150-tlmm-state" + - patternProperties: + "-pins$": + $ref: "#/$defs/qcom-sm7150-tlmm-state" + additionalProperties: false + +$defs: + qcom-sm7150-tlmm-state: + type: object + description: + Pinctrl node's client devices use subnodes for desired pin configuration. + Client device subnodes use below standard properties. + $ref: qcom,tlmm-common.yaml#/$defs/qcom-tlmm-state + + properties: + pins: + description: + List of gpio pins affected by the properties specified in this + subnode. + items: + oneOf: + - pattern: "^gpio([0-9]|[1-9][0-9]|10[0-9]|11[0-8])$" + - enum: [ sdc1_rclk, sdc1_clk, sdc1_cmd, sdc1_data, sdc2_clk, + sdc2_cmd, sdc2_data, ufs_reset ] + minItems: 1 + maxItems: 36 + + function: + description: + Specify the alternative function to be configured for the specified + pins. + + enum: [ gpio, adsp_ext, agera_pll, aoss_cti, atest_char, atest_tsens, + atest_tsens2, atest_usb1, atest_usb2, cam_mclk, cci_async, + cci_i2c, cci_timer0, cci_timer1, cci_timer2, cci_timer3, + cci_timer4, dbg_out, ddr_bist, ddr_pxi0, ddr_pxi1, ddr_pxi2, + ddr_pxi3, edp_hot, edp_lcd, gcc_gp1, gcc_gp2, gcc_gp3, gp_pdm0, + gp_pdm1, gp_pdm2, gps_tx, jitter_bist, ldo_en, ldo_update, + m_voc, mdp_vsync, mdp_vsync0, mdp_vsync1, mdp_vsync2, + mdp_vsync3, mss_lte, nav_pps_in, nav_pps_out, pa_indicator, + pci_e, phase_flag, pll_bist, pll_bypassnl, pll_reset, pri_mi2s, + pri_mi2s_ws, prng_rosc, qdss, qdss_cti, qlink_enable, + qlink_request, qua_mi2s, qup00, qup01, qup02, qup03, qup04, + qup10, qup11, qup12, qup13, qup14, qup15, sd_write, sdc40, + sdc41, sdc42, sdc43, sdc4_clk, sdc4_cmd, sec_mi2s, ter_mi2s, + tgu_ch0, tgu_ch1, tgu_ch2, tgu_ch3, tsif1_clk, tsif1_data, + tsif1_en, tsif1_error, tsif1_sync, tsif2_clk, tsif2_data, + tsif2_en, tsif2_error, tsif2_sync, uim1_clk, uim1_data, + uim1_present, uim1_reset, uim2_clk, uim2_data, uim2_present, + uim2_reset, uim_batt, usb_phy, vfr_1, vsense_trigger, + wlan1_adc0, wlan1_adc1, wlan2_adc0, wlan2_adc1, wsa_clk, + wsa_data ] + + bias-pull-down: true + bias-pull-up: true + bias-disable: true + drive-strength: true + input-enable: true + output-high: true + output-low: true + + required: + - pins + + additionalProperties: false + +required: + - compatible + - reg + - reg-names + +additionalProperties: false + +examples: + - | + #include <dt-bindings/interrupt-controller/arm-gic.h> + + tlmm: pinctrl@3500000 { + compatible = "qcom,sm7150-tlmm"; + reg = <0x03500000 0x300000>, + <0x03900000 0x300000>, + <0x03d00000 0x300000>; + reg-names = "west", "north", "south"; + interrupts = <GIC_SPI 208 IRQ_TYPE_LEVEL_HIGH>; + gpio-ranges = <&tlmm 0 0 120>; + gpio-controller; + #gpio-cells = <2>; + interrupt-controller; + #interrupt-cells = <2>; + wakeup-parent = <&pdc>; + + gpio-wo-state { + pins = "gpio1"; + function = "gpio"; + }; + + uart-w-state { + rx-pins { + pins = "gpio44"; + function = "qup12"; + bias-pull-up; + }; + + tx-pins { + pins = "gpio45"; + function = "qup12"; + bias-disable; + }; + }; + }; +... diff --git a/Documentation/devicetree/bindings/pinctrl/qcom,sm8150-pinctrl.yaml b/Documentation/devicetree/bindings/pinctrl/qcom,sm8150-pinctrl.yaml index 4376a9bd4d70..c6439626464e 100644 --- a/Documentation/devicetree/bindings/pinctrl/qcom,sm8150-pinctrl.yaml +++ b/Documentation/devicetree/bindings/pinctrl/qcom,sm8150-pinctrl.yaml @@ -60,6 +60,7 @@ $defs: Pinctrl node's client devices use subnodes for desired pin configuration. Client device subnodes use below standard properties. $ref: qcom,tlmm-common.yaml#/$defs/qcom-tlmm-state + unevaluatedProperties: false properties: pins: @@ -81,7 +82,7 @@ $defs: enum: [ adsp_ext, agera_pll, aoss_cti, ddr_pxi2, atest_char, atest_char0, atest_char1, atest_char2, atest_char3, audio_ref, atest_usb1, atest_usb2, atest_usb10, atest_usb11, atest_usb12, - atest_usb13, atest_usb20, atest_usb21, atest_usb22, atest_usb2, + atest_usb13, atest_usb20, atest_usb21, atest_usb22, atest_usb23, btfm_slimbus, cam_mclk, cci_async, cci_i2c, cci_timer0, cci_timer1, cci_timer2, cci_timer3, cci_timer4, cri_trng, cri_trng0, cri_trng1, dbg_out, ddr_bist, ddr_pxi0, @@ -101,19 +102,9 @@ $defs: usb_phy, vfr_1, vsense_trigger, wlan1_adc0, wlan1_adc1, wlan2_adc0, wlan2_adc1, wmss_reset ] - bias-pull-down: true - bias-pull-up: true - bias-disable: true - drive-strength: true - input-enable: true - output-high: true - output-low: true - required: - pins - additionalProperties: false - allOf: - $ref: /schemas/pinctrl/qcom,tlmm-common.yaml# diff --git a/Documentation/devicetree/bindings/pinctrl/qcom,sm8250-lpass-lpi-pinctrl.yaml b/Documentation/devicetree/bindings/pinctrl/qcom,sm8250-lpass-lpi-pinctrl.yaml index de9d8854c690..4b4be7efc150 100644 --- a/Documentation/devicetree/bindings/pinctrl/qcom,sm8250-lpass-lpi-pinctrl.yaml +++ b/Documentation/devicetree/bindings/pinctrl/qcom,sm8250-lpass-lpi-pinctrl.yaml @@ -55,7 +55,7 @@ $defs: description: Pinctrl node's client devices use subnodes for desired pin configuration. Client device subnodes use below standard properties. - $ref: "/schemas/pinctrl/pincfg-node.yaml" + $ref: /schemas/pinctrl/pincfg-node.yaml properties: pins: diff --git a/Documentation/devicetree/bindings/pinctrl/qcom,sm8250-pinctrl.yaml b/Documentation/devicetree/bindings/pinctrl/qcom,sm8250-pinctrl.yaml index cf561dff8893..021c54708524 100644 --- a/Documentation/devicetree/bindings/pinctrl/qcom,sm8250-pinctrl.yaml +++ b/Documentation/devicetree/bindings/pinctrl/qcom,sm8250-pinctrl.yaml @@ -58,6 +58,7 @@ $defs: Pinctrl node's client devices use subnodes for desired pin configuration. Client device subnodes use below standard properties. $ref: qcom,tlmm-common.yaml#/$defs/qcom-tlmm-state + unevaluatedProperties: false properties: pins: @@ -94,19 +95,9 @@ $defs: tsif0_en, tsif0_error, tsif0_sync, tsif1_clk, tsif1_data, tsif1_en, tsif1_error, tsif1_sync, usb2phy_ac, usb_phy, vsense_trigger ] - bias-pull-down: true - bias-pull-up: true - bias-disable: true - drive-strength: true - input-enable: true - output-high: true - output-low: true - required: - pins - additionalProperties: false - allOf: - $ref: /schemas/pinctrl/qcom,tlmm-common.yaml# diff --git a/Documentation/devicetree/bindings/pinctrl/qcom,sm8350-tlmm.yaml b/Documentation/devicetree/bindings/pinctrl/qcom,sm8350-tlmm.yaml index 797242f68b1c..6e8f41ff0a76 100644 --- a/Documentation/devicetree/bindings/pinctrl/qcom,sm8350-tlmm.yaml +++ b/Documentation/devicetree/bindings/pinctrl/qcom,sm8350-tlmm.yaml @@ -62,6 +62,7 @@ $defs: Pinctrl node's client devices use subnodes for desired pin configuration. Client device subnodes use below standard properties. $ref: qcom,tlmm-common.yaml#/$defs/qcom-tlmm-state + unevaluatedProperties: false properties: pins: @@ -104,21 +105,9 @@ $defs: uim0_present, uim0_reset, uim1_clk, uim1_data, uim1_present, uim1_reset, usb2phy_ac, usb_phy, vfr_0, vfr_1, vsense_trigger ] - - bias-disable: true - bias-pull-down: true - bias-pull-up: true - drive-strength: true - input-disable: true - input-enable: true - output-high: true - output-low: true - required: - pins - additionalProperties: false - examples: - | #include <dt-bindings/interrupt-controller/arm-gic.h> diff --git a/Documentation/devicetree/bindings/pinctrl/qcom,sm8450-lpass-lpi-pinctrl.yaml b/Documentation/devicetree/bindings/pinctrl/qcom,sm8450-lpass-lpi-pinctrl.yaml index 8bf51df0b231..1eefa9aa6a86 100644 --- a/Documentation/devicetree/bindings/pinctrl/qcom,sm8450-lpass-lpi-pinctrl.yaml +++ b/Documentation/devicetree/bindings/pinctrl/qcom,sm8450-lpass-lpi-pinctrl.yaml @@ -20,7 +20,7 @@ properties: reg: items: - description: LPASS LPI TLMM Control and Status registers - - description: LPASS LPI pins SLEW registers + - description: LPASS LPI MCC registers clocks: items: diff --git a/Documentation/devicetree/bindings/pinctrl/qcom,sm8450-tlmm.yaml b/Documentation/devicetree/bindings/pinctrl/qcom,sm8450-tlmm.yaml index 56c8046f1be0..5163fe3f5365 100644 --- a/Documentation/devicetree/bindings/pinctrl/qcom,sm8450-tlmm.yaml +++ b/Documentation/devicetree/bindings/pinctrl/qcom,sm8450-tlmm.yaml @@ -62,6 +62,7 @@ $defs: Pinctrl node's client devices use subnodes for desired pin configuration. Client device subnodes use below standard properties. $ref: qcom,tlmm-common.yaml#/$defs/qcom-tlmm-state + unevaluatedProperties: false properties: pins: @@ -103,19 +104,9 @@ $defs: uim0_reset, uim1_clk, uim1_data, uim1_present, uim1_reset, usb2phy_ac, usb_phy, vfr_0, vfr_1, vsense_trigger ] - bias-disable: true - bias-pull-down: true - bias-pull-up: true - drive-strength: true - input-enable: true - output-high: true - output-low: true - required: - pins - additionalProperties: false - examples: - | #include <dt-bindings/interrupt-controller/arm-gic.h> diff --git a/Documentation/devicetree/bindings/pinctrl/qcom,sm8550-lpass-lpi-pinctrl.yaml b/Documentation/devicetree/bindings/pinctrl/qcom,sm8550-lpass-lpi-pinctrl.yaml index 8f60a9113e7a..ef9743246849 100644 --- a/Documentation/devicetree/bindings/pinctrl/qcom,sm8550-lpass-lpi-pinctrl.yaml +++ b/Documentation/devicetree/bindings/pinctrl/qcom,sm8550-lpass-lpi-pinctrl.yaml @@ -21,7 +21,7 @@ properties: reg: items: - description: LPASS LPI TLMM Control and Status registers - - description: LPASS LPI pins SLEW registers + - description: LPASS LPI MCC registers clocks: items: diff --git a/Documentation/devicetree/bindings/pinctrl/qcom,sm8550-tlmm.yaml b/Documentation/devicetree/bindings/pinctrl/qcom,sm8550-tlmm.yaml index a457425ba112..f789c7753a92 100644 --- a/Documentation/devicetree/bindings/pinctrl/qcom,sm8550-tlmm.yaml +++ b/Documentation/devicetree/bindings/pinctrl/qcom,sm8550-tlmm.yaml @@ -54,6 +54,7 @@ $defs: Pinctrl node's client devices use subnodes for desired pin configuration. Client device subnodes use below standard properties. $ref: qcom,tlmm-common.yaml#/$defs/qcom-tlmm-state + unevaluatedProperties: false properties: pins: @@ -109,19 +110,9 @@ $defs: uim1_clk, uim1_data, uim1_present, uim1_reset, usb1_hs, usb_phy, vfr_0, vfr_1, vsense_trigger_mirnat ] - bias-disable: true - bias-pull-down: true - bias-pull-up: true - drive-strength: true - input-enable: true - output-high: true - output-low: true - required: - pins - additionalProperties: false - required: - compatible - reg diff --git a/Documentation/devicetree/bindings/pinctrl/qcom,tlmm-common.yaml b/Documentation/devicetree/bindings/pinctrl/qcom,tlmm-common.yaml index 90b7d75840c1..aae3dcf6cac8 100644 --- a/Documentation/devicetree/bindings/pinctrl/qcom,tlmm-common.yaml +++ b/Documentation/devicetree/bindings/pinctrl/qcom,tlmm-common.yaml @@ -52,7 +52,7 @@ properties: information. allOf: - - $ref: "pinctrl.yaml#" + - $ref: pinctrl.yaml# required: - interrupts diff --git a/Documentation/devicetree/bindings/pinctrl/ralink,rt2880-pinctrl.yaml b/Documentation/devicetree/bindings/pinctrl/ralink,rt2880-pinctrl.yaml index 7fd0df880a76..43b33dbf115b 100644 --- a/Documentation/devicetree/bindings/pinctrl/ralink,rt2880-pinctrl.yaml +++ b/Documentation/devicetree/bindings/pinctrl/ralink,rt2880-pinctrl.yaml @@ -10,7 +10,7 @@ maintainers: - Arınç ÜNAL <arinc.unal@arinc9.com> - Sergio Paracuellos <sergio.paracuellos@gmail.com> -description: +description: | Ralink RT2880 pin controller for RT2880 SoC. The pin controller can only set the muxing of pin groups. Muxing individual pins is not supported. There is no pinconf support. @@ -22,11 +22,14 @@ properties: patternProperties: '-pins$': type: object + additionalProperties: false + patternProperties: '^(.*-)?pinmux$': type: object description: node for pinctrl. $ref: pinmux-node.yaml# + additionalProperties: false properties: function: @@ -116,12 +119,8 @@ patternProperties: groups: enum: [pci] - additionalProperties: false - - additionalProperties: false - allOf: - - $ref: "pinctrl.yaml#" + - $ref: pinctrl.yaml# required: - compatible diff --git a/Documentation/devicetree/bindings/pinctrl/ralink,rt305x-pinctrl.yaml b/Documentation/devicetree/bindings/pinctrl/ralink,rt305x-pinctrl.yaml index 4d66ca752a30..95a904273009 100644 --- a/Documentation/devicetree/bindings/pinctrl/ralink,rt305x-pinctrl.yaml +++ b/Documentation/devicetree/bindings/pinctrl/ralink,rt305x-pinctrl.yaml @@ -10,9 +10,8 @@ maintainers: - Arınç ÜNAL <arinc.unal@arinc9.com> - Sergio Paracuellos <sergio.paracuellos@gmail.com> -description: - Ralink RT305X pin controller for RT3050, RT3052, RT3350, RT3352 and RT5350 - SoCs. +description: | + Ralink RT305X pin controller for RT3050, RT3052, and RT3350 SoCs. The pin controller can only set the muxing of pin groups. Muxing individual pins is not supported. There is no pinconf support. @@ -23,31 +22,22 @@ properties: patternProperties: '-pins$': type: object + additionalProperties: false + patternProperties: '^(.*-)?pinmux$': type: object description: node for pinctrl. $ref: pinmux-node.yaml# + additionalProperties: false properties: function: description: A string containing the name of the function to mux to the group. - anyOf: - - description: For RT3050, RT3052 and RT3350 SoCs - enum: [gpio, gpio i2s, gpio uartf, i2c, i2s uartf, jtag, mdio, - pcm gpio, pcm i2s, pcm uartf, rgmii, sdram, spi, uartf, - uartlite] - - - description: For RT3352 SoC - enum: [gpio, gpio i2s, gpio uartf, i2c, i2s uartf, jtag, led, - lna, mdio, pa, pcm gpio, pcm i2s, pcm uartf, rgmii, spi, - spi_cs1, uartf, uartlite, wdg_cs1] - - - description: For RT5350 SoC - enum: [gpio, gpio i2s, gpio uartf, i2c, i2s uartf, jtag, led, - pcm gpio, pcm i2s, pcm uartf, spi, spi_cs1, uartf, - uartlite, wdg_cs1] + enum: [gpio, gpio i2s, gpio uartf, i2c, i2s uartf, jtag, mdio, + pcm gpio, pcm i2s, pcm uartf, rgmii, sdram, spi, uartf, + uartlite] groups: description: @@ -66,17 +56,7 @@ patternProperties: then: properties: groups: - anyOf: - - description: For RT3050, RT3052 and RT3350 SoCs - enum: [i2c, jtag, mdio, rgmii, sdram, spi, uartf, - uartlite] - - - description: For RT3352 SoC - enum: [i2c, jtag, led, lna, mdio, pa, rgmii, spi, spi_cs1, - uartf, uartlite] - - - description: For RT5350 SoC - enum: [i2c, jtag, led, spi, spi_cs1, uartf, uartlite] + enum: [i2c, jtag, mdio, rgmii, sdram, spi, uartf, uartlite] - if: properties: @@ -126,24 +106,6 @@ patternProperties: - if: properties: function: - const: led - then: - properties: - groups: - enum: [led] - - - if: - properties: - function: - const: lna - then: - properties: - groups: - enum: [lna] - - - if: - properties: - function: const: mdio then: properties: @@ -153,15 +115,6 @@ patternProperties: - if: properties: function: - const: pa - then: - properties: - groups: - enum: [pa] - - - if: - properties: - function: const: pcm gpio then: properties: @@ -216,15 +169,6 @@ patternProperties: - if: properties: function: - const: spi_cs1 - then: - properties: - groups: - enum: [spi_cs1] - - - if: - properties: - function: const: uartf then: properties: @@ -240,21 +184,8 @@ patternProperties: groups: enum: [uartlite] - - if: - properties: - function: - const: wdg_cs1 - then: - properties: - groups: - enum: [spi_cs1] - - additionalProperties: false - - additionalProperties: false - allOf: - - $ref: "pinctrl.yaml#" + - $ref: pinctrl.yaml# required: - compatible diff --git a/Documentation/devicetree/bindings/pinctrl/ralink,rt3352-pinctrl.yaml b/Documentation/devicetree/bindings/pinctrl/ralink,rt3352-pinctrl.yaml new file mode 100644 index 000000000000..c9bc6cfd834c --- /dev/null +++ b/Documentation/devicetree/bindings/pinctrl/ralink,rt3352-pinctrl.yaml @@ -0,0 +1,243 @@ +# SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/pinctrl/ralink,rt3352-pinctrl.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Ralink RT3352 Pin Controller + +maintainers: + - Arınç ÜNAL <arinc.unal@arinc9.com> + - Sergio Paracuellos <sergio.paracuellos@gmail.com> + +description: | + Ralink RT3352 pin controller for RT3352 SoC. + The pin controller can only set the muxing of pin groups. Muxing individual + pins is not supported. There is no pinconf support. + +properties: + compatible: + const: ralink,rt3352-pinctrl + +patternProperties: + '-pins$': + type: object + additionalProperties: false + + patternProperties: + '^(.*-)?pinmux$': + type: object + description: node for pinctrl. + $ref: pinmux-node.yaml# + additionalProperties: false + + properties: + function: + description: + A string containing the name of the function to mux to the group. + enum: [gpio, gpio i2s, gpio uartf, i2c, i2s uartf, jtag, led, lna, + mdio, pa, pcm gpio, pcm i2s, pcm uartf, rgmii, spi, spi_cs1, + uartf, uartlite, wdg_cs1] + + groups: + description: + An array of strings. Each string contains the name of a group. + maxItems: 1 + + required: + - groups + - function + + allOf: + - if: + properties: + function: + const: gpio + then: + properties: + groups: + enum: [i2c, jtag, led, lna, mdio, pa, rgmii, spi, spi_cs1, + uartf, uartlite] + + - if: + properties: + function: + const: gpio i2s + then: + properties: + groups: + enum: [uartf] + + - if: + properties: + function: + const: gpio uartf + then: + properties: + groups: + enum: [uartf] + + - if: + properties: + function: + const: i2c + then: + properties: + groups: + enum: [i2c] + + - if: + properties: + function: + const: i2s uartf + then: + properties: + groups: + enum: [uartf] + + - if: + properties: + function: + const: jtag + then: + properties: + groups: + enum: [jtag] + + - if: + properties: + function: + const: led + then: + properties: + groups: + enum: [led] + + - if: + properties: + function: + const: lna + then: + properties: + groups: + enum: [lna] + + - if: + properties: + function: + const: mdio + then: + properties: + groups: + enum: [mdio] + + - if: + properties: + function: + const: pa + then: + properties: + groups: + enum: [pa] + + - if: + properties: + function: + const: pcm gpio + then: + properties: + groups: + enum: [uartf] + + - if: + properties: + function: + const: pcm i2s + then: + properties: + groups: + enum: [uartf] + + - if: + properties: + function: + const: pcm uartf + then: + properties: + groups: + enum: [uartf] + + - if: + properties: + function: + const: rgmii + then: + properties: + groups: + enum: [rgmii] + + - if: + properties: + function: + const: spi + then: + properties: + groups: + enum: [spi] + + - if: + properties: + function: + const: spi_cs1 + then: + properties: + groups: + enum: [spi_cs1] + + - if: + properties: + function: + const: uartf + then: + properties: + groups: + enum: [uartf] + + - if: + properties: + function: + const: uartlite + then: + properties: + groups: + enum: [uartlite] + + - if: + properties: + function: + const: wdg_cs1 + then: + properties: + groups: + enum: [spi_cs1] + +allOf: + - $ref: pinctrl.yaml# + +required: + - compatible + +additionalProperties: false + +examples: + - | + pinctrl { + compatible = "ralink,rt3352-pinctrl"; + + i2c_pins: i2c0-pins { + pinmux { + groups = "i2c"; + function = "i2c"; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/pinctrl/ralink,rt3883-pinctrl.yaml b/Documentation/devicetree/bindings/pinctrl/ralink,rt3883-pinctrl.yaml index 008d93181aea..8d14e525b25e 100644 --- a/Documentation/devicetree/bindings/pinctrl/ralink,rt3883-pinctrl.yaml +++ b/Documentation/devicetree/bindings/pinctrl/ralink,rt3883-pinctrl.yaml @@ -10,7 +10,7 @@ maintainers: - Arınç ÜNAL <arinc.unal@arinc9.com> - Sergio Paracuellos <sergio.paracuellos@gmail.com> -description: +description: | Ralink RT3883 pin controller for RT3883 SoC. The pin controller can only set the muxing of pin groups. Muxing individual pins is not supported. There is no pinconf support. @@ -22,11 +22,14 @@ properties: patternProperties: '-pins$': type: object + additionalProperties: false + patternProperties: '^(.*-)?pinmux$': type: object description: node for pinctrl. $ref: pinmux-node.yaml# + additionalProperties: false properties: function: @@ -236,12 +239,8 @@ patternProperties: groups: enum: [uartlite] - additionalProperties: false - - additionalProperties: false - allOf: - - $ref: "pinctrl.yaml#" + - $ref: pinctrl.yaml# required: - compatible diff --git a/Documentation/devicetree/bindings/pinctrl/ralink,rt5350-pinctrl.yaml b/Documentation/devicetree/bindings/pinctrl/ralink,rt5350-pinctrl.yaml new file mode 100644 index 000000000000..f248202ce866 --- /dev/null +++ b/Documentation/devicetree/bindings/pinctrl/ralink,rt5350-pinctrl.yaml @@ -0,0 +1,206 @@ +# SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/pinctrl/ralink,rt5350-pinctrl.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Ralink RT5350 Pin Controller + +maintainers: + - Arınç ÜNAL <arinc.unal@arinc9.com> + - Sergio Paracuellos <sergio.paracuellos@gmail.com> + +description: | + Ralink RT5350 pin controller for RT5350 SoC. + The pin controller can only set the muxing of pin groups. Muxing individual + pins is not supported. There is no pinconf support. + +properties: + compatible: + const: ralink,rt5350-pinctrl + +patternProperties: + '-pins$': + type: object + additionalProperties: false + + patternProperties: + '^(.*-)?pinmux$': + type: object + description: node for pinctrl. + $ref: pinmux-node.yaml# + additionalProperties: false + + properties: + function: + description: + A string containing the name of the function to mux to the group. + enum: [gpio, gpio i2s, gpio uartf, i2c, i2s uartf, jtag, led, + pcm gpio, pcm i2s, pcm uartf, spi, spi_cs1, uartf, uartlite, + wdg_cs1] + + groups: + description: + An array of strings. Each string contains the name of a group. + maxItems: 1 + + required: + - groups + - function + + allOf: + - if: + properties: + function: + const: gpio + then: + properties: + groups: + enum: [i2c, jtag, led, spi, spi_cs1, uartf, uartlite] + + - if: + properties: + function: + const: gpio i2s + then: + properties: + groups: + enum: [uartf] + + - if: + properties: + function: + const: gpio uartf + then: + properties: + groups: + enum: [uartf] + + - if: + properties: + function: + const: i2c + then: + properties: + groups: + enum: [i2c] + + - if: + properties: + function: + const: i2s uartf + then: + properties: + groups: + enum: [uartf] + + - if: + properties: + function: + const: jtag + then: + properties: + groups: + enum: [jtag] + + - if: + properties: + function: + const: led + then: + properties: + groups: + enum: [led] + + - if: + properties: + function: + const: pcm gpio + then: + properties: + groups: + enum: [uartf] + + - if: + properties: + function: + const: pcm i2s + then: + properties: + groups: + enum: [uartf] + + - if: + properties: + function: + const: pcm uartf + then: + properties: + groups: + enum: [uartf] + + - if: + properties: + function: + const: spi + then: + properties: + groups: + enum: [spi] + + - if: + properties: + function: + const: spi_cs1 + then: + properties: + groups: + enum: [spi_cs1] + + - if: + properties: + function: + const: uartf + then: + properties: + groups: + enum: [uartf] + + - if: + properties: + function: + const: uartlite + then: + properties: + groups: + enum: [uartlite] + + - if: + properties: + function: + const: wdg_cs1 + then: + properties: + groups: + enum: [spi_cs1] + +allOf: + - $ref: pinctrl.yaml# + +required: + - compatible + +additionalProperties: false + +examples: + - | + pinctrl { + compatible = "ralink,rt5350-pinctrl"; + + i2c_pins: i2c0-pins { + pinmux { + groups = "i2c"; + function = "i2c"; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/pinctrl/renesas,pfc.yaml b/Documentation/devicetree/bindings/pinctrl/renesas,pfc.yaml index 4fc758fea7e6..0fc3c0f52c19 100644 --- a/Documentation/devicetree/bindings/pinctrl/renesas,pfc.yaml +++ b/Documentation/devicetree/bindings/pinctrl/renesas,pfc.yaml @@ -73,7 +73,7 @@ properties: maxItems: 1 allOf: - - $ref: "pinctrl.yaml#" + - $ref: pinctrl.yaml# required: - compatible diff --git a/Documentation/devicetree/bindings/pinctrl/renesas,rza1-ports.yaml b/Documentation/devicetree/bindings/pinctrl/renesas,rza1-ports.yaml index 9083040c996a..83800fcf0ce4 100644 --- a/Documentation/devicetree/bindings/pinctrl/renesas,rza1-ports.yaml +++ b/Documentation/devicetree/bindings/pinctrl/renesas,rza1-ports.yaml @@ -32,7 +32,7 @@ properties: maxItems: 1 allOf: - - $ref: "pinctrl.yaml#" + - $ref: pinctrl.yaml# required: - compatible diff --git a/Documentation/devicetree/bindings/pinctrl/renesas,rza2-pinctrl.yaml b/Documentation/devicetree/bindings/pinctrl/renesas,rza2-pinctrl.yaml index d761fddc2206..37173a64fed2 100644 --- a/Documentation/devicetree/bindings/pinctrl/renesas,rza2-pinctrl.yaml +++ b/Documentation/devicetree/bindings/pinctrl/renesas,rza2-pinctrl.yaml @@ -73,7 +73,7 @@ patternProperties: additionalProperties: false allOf: - - $ref: "pinctrl.yaml#" + - $ref: pinctrl.yaml# required: - compatible diff --git a/Documentation/devicetree/bindings/pinctrl/renesas,rzg2l-pinctrl.yaml b/Documentation/devicetree/bindings/pinctrl/renesas,rzg2l-pinctrl.yaml index f081acb7ba04..9ce1a07fc015 100644 --- a/Documentation/devicetree/bindings/pinctrl/renesas,rzg2l-pinctrl.yaml +++ b/Documentation/devicetree/bindings/pinctrl/renesas,rzg2l-pinctrl.yaml @@ -113,7 +113,7 @@ additionalProperties: $ref: "#/additionalProperties/anyOf/0" allOf: - - $ref: "pinctrl.yaml#" + - $ref: pinctrl.yaml# required: - compatible diff --git a/Documentation/devicetree/bindings/pinctrl/renesas,rzn1-pinctrl.yaml b/Documentation/devicetree/bindings/pinctrl/renesas,rzn1-pinctrl.yaml index 70b1788ab594..f3b85b7eae31 100644 --- a/Documentation/devicetree/bindings/pinctrl/renesas,rzn1-pinctrl.yaml +++ b/Documentation/devicetree/bindings/pinctrl/renesas,rzn1-pinctrl.yaml @@ -32,7 +32,7 @@ properties: The bus clock, sometimes described as pclk, for register accesses. allOf: - - $ref: "pinctrl.yaml#" + - $ref: pinctrl.yaml# required: - compatible diff --git a/Documentation/devicetree/bindings/pinctrl/renesas,rzv2m-pinctrl.yaml b/Documentation/devicetree/bindings/pinctrl/renesas,rzv2m-pinctrl.yaml index eac6245db7dc..03f084292d68 100644 --- a/Documentation/devicetree/bindings/pinctrl/renesas,rzv2m-pinctrl.yaml +++ b/Documentation/devicetree/bindings/pinctrl/renesas,rzv2m-pinctrl.yaml @@ -94,7 +94,7 @@ additionalProperties: $ref: "#/additionalProperties/anyOf/0" allOf: - - $ref: "pinctrl.yaml#" + - $ref: pinctrl.yaml# required: - compatible diff --git a/Documentation/devicetree/bindings/pinctrl/rockchip,pinctrl.yaml b/Documentation/devicetree/bindings/pinctrl/rockchip,pinctrl.yaml index 45b767986a87..10c335efe619 100644 --- a/Documentation/devicetree/bindings/pinctrl/rockchip,pinctrl.yaml +++ b/Documentation/devicetree/bindings/pinctrl/rockchip,pinctrl.yaml @@ -50,12 +50,12 @@ properties: - rockchip,rv1126-pinctrl rockchip,grf: - $ref: "/schemas/types.yaml#/definitions/phandle" + $ref: /schemas/types.yaml#/definitions/phandle description: The phandle of the syscon node for the GRF registers. rockchip,pmu: - $ref: "/schemas/types.yaml#/definitions/phandle" + $ref: /schemas/types.yaml#/definitions/phandle description: The phandle of the syscon node for the PMU registers, as some SoCs carry parts of the iomux controller registers there. @@ -71,7 +71,7 @@ properties: ranges: true allOf: - - $ref: "pinctrl.yaml#" + - $ref: pinctrl.yaml# required: - compatible @@ -81,7 +81,7 @@ patternProperties: "gpio@[0-9a-f]+$": type: object - $ref: "/schemas/gpio/rockchip,gpio-bank.yaml#" + $ref: /schemas/gpio/rockchip,gpio-bank.yaml# deprecated: true unevaluatedProperties: false @@ -117,7 +117,7 @@ additionalProperties: type: object properties: rockchip,pins: - $ref: "/schemas/types.yaml#/definitions/uint32-matrix" + $ref: /schemas/types.yaml#/definitions/uint32-matrix minItems: 1 items: items: diff --git a/Documentation/devicetree/bindings/pinctrl/samsung,pinctrl.yaml b/Documentation/devicetree/bindings/pinctrl/samsung,pinctrl.yaml index eb2b2692607d..26614621774a 100644 --- a/Documentation/devicetree/bindings/pinctrl/samsung,pinctrl.yaml +++ b/Documentation/devicetree/bindings/pinctrl/samsung,pinctrl.yaml @@ -117,7 +117,7 @@ required: - reg allOf: - - $ref: "pinctrl.yaml#" + - $ref: pinctrl.yaml# - if: properties: compatible: diff --git a/Documentation/devicetree/bindings/pinctrl/semtech,sx1501q.yaml b/Documentation/devicetree/bindings/pinctrl/semtech,sx1501q.yaml index 0719c03d6f4b..4214d7311f6b 100644 --- a/Documentation/devicetree/bindings/pinctrl/semtech,sx1501q.yaml +++ b/Documentation/devicetree/bindings/pinctrl/semtech,sx1501q.yaml @@ -62,8 +62,8 @@ patternProperties: - pins allOf: - - $ref: "pincfg-node.yaml#" - - $ref: "pinmux-node.yaml#" + - $ref: pincfg-node.yaml# + - $ref: pinmux-node.yaml# - if: properties: pins: @@ -86,7 +86,7 @@ required: - gpio-controller allOf: - - $ref: "pinctrl.yaml#" + - $ref: pinctrl.yaml# - if: not: properties: diff --git a/Documentation/devicetree/bindings/pinctrl/socionext,uniphier-pinctrl.yaml b/Documentation/devicetree/bindings/pinctrl/socionext,uniphier-pinctrl.yaml index bc34e2c872bc..a6f34df82e90 100644 --- a/Documentation/devicetree/bindings/pinctrl/socionext,uniphier-pinctrl.yaml +++ b/Documentation/devicetree/bindings/pinctrl/socionext,uniphier-pinctrl.yaml @@ -61,7 +61,7 @@ additionalProperties: unevaluatedProperties: false allOf: - - $ref: "pinctrl.yaml#" + - $ref: pinctrl.yaml# required: - compatible diff --git a/Documentation/devicetree/bindings/pinctrl/st,stm32-pinctrl.yaml b/Documentation/devicetree/bindings/pinctrl/st,stm32-pinctrl.yaml index eeb29b4ad4d1..1ab0f8dde477 100644 --- a/Documentation/devicetree/bindings/pinctrl/st,stm32-pinctrl.yaml +++ b/Documentation/devicetree/bindings/pinctrl/st,stm32-pinctrl.yaml @@ -44,7 +44,7 @@ properties: st,syscfg: description: Phandle+args to the syscon node which includes IRQ mux selection. - $ref: "/schemas/types.yaml#/definitions/phandle-array" + $ref: /schemas/types.yaml#/definitions/phandle-array items: - items: - description: syscon node which includes IRQ mux selection @@ -89,7 +89,7 @@ patternProperties: st,bank-name: description: Should be a name string for this bank as specified in the datasheet. - $ref: "/schemas/types.yaml#/definitions/string" + $ref: /schemas/types.yaml#/definitions/string enum: - GPIOA - GPIOB @@ -108,7 +108,7 @@ patternProperties: description: Should correspond to the EXTI IOport selection (EXTI line used to select GPIOs as interrupts). - $ref: "/schemas/types.yaml#/definitions/uint32" + $ref: /schemas/types.yaml#/definitions/uint32 minimum: 0 maximum: 11 @@ -140,7 +140,7 @@ patternProperties: configuration, pullups, drive, output high/low and output speed. properties: pinmux: - $ref: "/schemas/types.yaml#/definitions/uint32-array" + $ref: /schemas/types.yaml#/definitions/uint32-array description: | Integer array, represents gpio pin number and mux setting. Supported pin number and mux varies for different SoCs, and are @@ -201,7 +201,7 @@ patternProperties: - pinmux allOf: - - $ref: "pinctrl.yaml#" + - $ref: pinctrl.yaml# required: - compatible diff --git a/Documentation/devicetree/bindings/pinctrl/starfive,jh7100-pinctrl.yaml b/Documentation/devicetree/bindings/pinctrl/starfive,jh7100-pinctrl.yaml index d78c3cd0c295..f3258f2fd3a4 100644 --- a/Documentation/devicetree/bindings/pinctrl/starfive,jh7100-pinctrl.yaml +++ b/Documentation/devicetree/bindings/pinctrl/starfive,jh7100-pinctrl.yaml @@ -111,7 +111,7 @@ patternProperties: pins it needs, and how they should be configured, with regard to muxer configuration, bias, input enable/disable, input schmitt trigger enable/disable, slew-rate and drive strength. - $ref: "/schemas/pinctrl/pincfg-node.yaml" + $ref: /schemas/pinctrl/pincfg-node.yaml properties: pins: @@ -120,14 +120,14 @@ patternProperties: This should be set using either the PAD_GPIO or PAD_FUNC_SHARE macros. Either this or "pinmux" has to be specified, but not both. - $ref: "/schemas/pinctrl/pinmux-node.yaml#/properties/pins" + $ref: /schemas/pinctrl/pinmux-node.yaml#/properties/pins pinmux: description: | The list of GPIOs and their mux settings that properties in the node apply to. This should be set using the GPIOMUX macro. Either this or "pins" has to be specified, but not both. - $ref: "/schemas/pinctrl/pinmux-node.yaml#/properties/pinmux" + $ref: /schemas/pinctrl/pinmux-node.yaml#/properties/pinmux bias-disable: true diff --git a/Documentation/devicetree/bindings/pinctrl/sunplus,sp7021-pinctrl.yaml b/Documentation/devicetree/bindings/pinctrl/sunplus,sp7021-pinctrl.yaml index 347061eece9e..94b868c7ceb1 100644 --- a/Documentation/devicetree/bindings/pinctrl/sunplus,sp7021-pinctrl.yaml +++ b/Documentation/devicetree/bindings/pinctrl/sunplus,sp7021-pinctrl.yaml @@ -138,7 +138,7 @@ patternProperties: description: | Define pin-function which is used by pinctrl node's client device. The name should be one of string in the following enumeration. - $ref: "/schemas/types.yaml#/definitions/string" + $ref: /schemas/types.yaml#/definitions/string enum: [ SPI_FLASH, SPI_FLASH_4BIT, SPI_NAND, CARD0_EMMC, SD_CARD, UA0, FPGA_IFX, HDMI_TX, LCDIF, USB0_OTG, USB1_OTG ] @@ -146,7 +146,7 @@ patternProperties: description: | Define pin-group in a specified pin-function. The name should be one of string in the following enumeration. - $ref: "/schemas/types.yaml#/definitions/string" + $ref: /schemas/types.yaml#/definitions/string enum: [ SPI_FLASH1, SPI_FLASH2, SPI_FLASH_4BIT1, SPI_FLASH_4BIT2, SPI_NAND, CARD0_EMMC, SD_CARD, UA0, FPGA_IFX, HDMI_TX1, HDMI_TX2, HDMI_TX3, LCDIF, USB0_OTG, USB1_OTG ] @@ -289,7 +289,7 @@ required: additionalProperties: false allOf: - - $ref: "pinctrl.yaml#" + - $ref: pinctrl.yaml# examples: - | diff --git a/Documentation/devicetree/bindings/pinctrl/toshiba,visconti-pinctrl.yaml b/Documentation/devicetree/bindings/pinctrl/toshiba,visconti-pinctrl.yaml index 98b4663f9766..19d47fd414bc 100644 --- a/Documentation/devicetree/bindings/pinctrl/toshiba,visconti-pinctrl.yaml +++ b/Documentation/devicetree/bindings/pinctrl/toshiba,visconti-pinctrl.yaml @@ -21,7 +21,7 @@ properties: maxItems: 1 allOf: - - $ref: "pinctrl.yaml#" + - $ref: pinctrl.yaml# required: - compatible @@ -35,14 +35,14 @@ patternProperties: pinctrl groups available on the machine. Each subnode will list the pins it needs, and how they should be configured, with regard to muxer configuration, pullups, drive strength. - $ref: "pinmux-node.yaml" + $ref: pinmux-node.yaml additionalProperties: false properties: function: description: Function to mux. - $ref: "/schemas/types.yaml#/definitions/string" + $ref: /schemas/types.yaml#/definitions/string enum: [i2c0, i2c1, i2c2, i2c3, i2c4, i2c5, i2c6, i2c7, i2c8, spi0, spi1, spi2, spi3, spi4, spi5, spi6, uart0, uart1, uart2, uart3, pwm, pcmif_out, pcmif_in] @@ -50,7 +50,7 @@ patternProperties: groups: description: Name of the pin group to use for the functions. - $ref: "/schemas/types.yaml#/definitions/string" + $ref: /schemas/types.yaml#/definitions/string enum: [i2c0_grp, i2c1_grp, i2c2_grp, i2c3_grp, i2c4_grp, i2c5_grp, i2c6_grp, i2c7_grp, i2c8_grp, spi0_grp, spi0_cs0_grp, spi0_cs1_grp, spi0_cs2_grp, diff --git a/Documentation/devicetree/bindings/pinctrl/xlnx,zynq-pinctrl.yaml b/Documentation/devicetree/bindings/pinctrl/xlnx,zynq-pinctrl.yaml index cfd0cc549a7b..598a042850b8 100644 --- a/Documentation/devicetree/bindings/pinctrl/xlnx,zynq-pinctrl.yaml +++ b/Documentation/devicetree/bindings/pinctrl/xlnx,zynq-pinctrl.yaml @@ -168,7 +168,7 @@ patternProperties: additionalProperties: false allOf: - - $ref: "pinctrl.yaml#" + - $ref: pinctrl.yaml# required: - compatible |