Merge tag 'gpio-v4.1-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio

Pull GPIO updates from Linus Walleij:
 "This is the bulk of GPIO changes for the v4.1 development cycle:

   - A new GPIO hogging mechanism has been added.  This can be used on
     boards that want to drive some GPIO line high, low, or set it as
     input on boot and then never touch it again.  For some embedded
     systems this is bliss and simplifies things to a great extent.

   - Some API cleanup and closure: gpiod_get_array() and
     gpiod_put_array() has been added to get and put GPIOs in bulk as
     was possible with the non-descriptor API.

   - Encapsulate cross-calls to the pin control subsystem in
     <linux/gpio/driver.h>.  Now this should be the only header any GPIO
     driver needs to include or something is wrong.  Cleanups
     restricting drivers to this include are welcomed if tested.

   - Sort the GPIO Kconfig and split it into submenus, as it was
     becoming and unstructured, illogical and unnavigatable mess.  I
     hope this is easier to follow.  Menus that require a certain
     subsystem like I2C can now be hidden nicely for example, still
     working on others.

   - New drivers:

       - New driver for the Altera Soft GPIO.

       - The F7188x driver now handles the F71869 and F71869A variants.

       - The MIPS Loongson driver has been moved to drivers/gpio for
         consolidation and cleanup.

   - Cleanups:

       - The MAX732x is converted to use the GPIOLIB_IRQCHIP
         infrastructure.

       - The PCF857x is converted to use the GPIOLIB_IRQCHIP
         infrastructure.

       - Radical cleanup of the OMAP driver.

   - Misc:

       - Enable the DWAPB GPIO for all architectures.  This is a "hard
         IP" block from Synopsys which has started to turn up in so
         diverse architectures as X86 Quark, ARC and a slew of ARM
         systems.  So even though it's not an expander, it's generic
         enough to be available for all.

       - We add a mock GPIO on Crystalcove PMIC after a long discussion
         with Daniel Vetter et al, tracing back to the shootout at the
         kernel summit where DRM drivers and sub-componentization was
         discussed.  In this case a mock GPIO is assumed to be the best
         compromise gaining some reuse of infrastructure without making
         DRM drivers overly complex at the same time.  Let's see"

* tag 'gpio-v4.1-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio: (62 commits)
  Revert "gpio: sch: use uapi/linux/pci_ids.h directly"
  gpio: dwapb: remove dependencies
  gpio: dwapb: enable for ARC
  gpio: removing kfree remove functionality
  gpio: mvebu: Fix mask/unmask managment per irq chip type
  gpio: split GPIO drivers in submenus
  gpio: move MFD GPIO drivers under their own comment
  gpio: move BCM Kona Kconfig option
  gpio: arrange SPI Kconfig symbols alphabetically
  gpio: arrange PCI GPIO controllers alphabetically
  gpio: arrange I2C Kconfig symbols alphabetically
  gpio: arrange Kconfig symbols alphabetically
  gpio: ich: Implement get_direction function
  gpio: use (!foo) instead of (foo == NULL)
  gpio: arizona: drop owner assignment from platform_drivers
  gpio: max7300: remove 'ret' variable
  gpio: use devm_kzalloc
  gpio: sch: use uapi/linux/pci_ids.h directly
  gpio: x-gene: fix devm_ioremap_resource() check
  gpio: loongson: Add Loongson-3A/3B GPIO driver support
  ...

3 files changed, 74 insertions, 1 deletions

diff --git a/Documentation/devicetree/bindings/gpio/gpio-altera.txt b/Documentation/devicetree/bindings/gpio/gpio-altera.txt
new file mode 100644
index 000000000000..12f50149e1ed
--- /dev/null
+++ b/Documentation/devicetree/bindings/gpio/gpio-altera.txt
@@ -0,0 +1,43 @@
+Altera GPIO controller bindings
+
+Required properties:
+- compatible:
+  - "altr,pio-1.0"
+- reg: Physical base address and length of the controller's registers.
+- #gpio-cells : Should be 2
+  - The first cell is the gpio offset number.
+  - The second cell is reserved and is currently unused.
+- gpio-controller : Marks the device node as a GPIO controller.
+- interrupt-controller: Mark the device node as an interrupt controller
+- #interrupt-cells : Should be 1. The interrupt type is fixed in the hardware.
+  - The first cell is the GPIO offset number within the GPIO controller.
+- interrupts: Specify the interrupt.
+- altr,interrupt-trigger: Specifies the interrupt trigger type the GPIO
+  hardware is synthesized. This field is required if the Altera GPIO controller
+  used has IRQ enabled as the interrupt type is not software controlled,
+  but hardware synthesized. Required if GPIO is used as an interrupt
+  controller. The value is defined in <dt-bindings/interrupt-controller/irq.h>
+  Only the following flags are supported:
+    IRQ_TYPE_EDGE_RISING
+    IRQ_TYPE_EDGE_FALLING
+    IRQ_TYPE_EDGE_BOTH
+    IRQ_TYPE_LEVEL_HIGH
+
+Optional properties:
+- altr,ngpio: Width of the GPIO bank. This defines how many pins the
+  GPIO device has. Ranges between 1-32. Optional and defaults to 32 if not
+  specified.
+
+Example:
+
+gpio_altr: gpio@0xff200000 {
+	compatible = "altr,pio-1.0";
+	reg = <0xff200000 0x10>;
+	interrupts = <0 45 4>;
+	altr,ngpio = <32>;
+	altr,interrupt-trigger = <IRQ_TYPE_EDGE_RISING>;
+	#gpio-cells = <2>;
+	gpio-controller;
+	#interrupt-cells = <1>;
+	interrupt-controller;
+};
diff --git a/Documentation/devicetree/bindings/gpio/gpio.txt b/Documentation/devicetree/bindings/gpio/gpio.txt
index f7a158d85862..5788d5cf1252 100644
--- a/Documentation/devicetree/bindings/gpio/gpio.txt
+++ b/Documentation/devicetree/bindings/gpio/gpio.txt
@@ -116,6 +116,29 @@ Every GPIO controller node must contain both an empty "gpio-controller"
 property, and a #gpio-cells integer property, which indicates the number of
 cells in a gpio-specifier.
 
+The GPIO chip may contain GPIO hog definitions. GPIO hogging is a mechanism
+providing automatic GPIO request and configuration as part of the
+gpio-controller's driver probe function.
+
+Each GPIO hog definition is represented as a child node of the GPIO controller.
+Required properties:
+- gpio-hog:   A property specifying that this child node represent a GPIO hog.
+- gpios:      Store the GPIO information (id, flags, ...). Shall contain the
+	      number of cells specified in its parent node (GPIO controller
+	      node).
+Only one of the following properties scanned in the order shown below.
+This means that when multiple properties are present they will be searched
+in the order presented below and the first match is taken as the intended
+configuration.
+- input:      A property specifying to set the GPIO direction as input.
+- output-low  A property specifying to set the GPIO direction as output with
+	      the value low.
+- output-high A property specifying to set the GPIO direction as output with
+	      the value high.
+
+Optional properties:
+- line-name:  The GPIO label name. If not present the node name is used.
+
 Example of two SOC GPIO banks defined as gpio-controller nodes:
 
 	qe_pio_a: gpio-controller@1400 {
@@ -123,6 +146,13 @@ Example of two SOC GPIO banks defined as gpio-controller nodes:
 		reg = <0x1400 0x18>;
 		gpio-controller;
 		#gpio-cells = <2>;
+
+		line_b {
+			gpio-hog;
+			gpios = <6 0>;
+			output-low;
+			line-name = "foo-bar-gpio";
+		};
 	};
 
 	qe_pio_e: gpio-controller@1460 {
diff --git a/Documentation/devicetree/bindings/gpio/mrvl-gpio.txt b/Documentation/devicetree/bindings/gpio/mrvl-gpio.txt
index 67a2e4e414a5..98d198396956 100644
--- a/Documentation/devicetree/bindings/gpio/mrvl-gpio.txt
+++ b/Documentation/devicetree/bindings/gpio/mrvl-gpio.txt
@@ -12,7 +12,7 @@ Required properties:
   gpio_mux.
 - interrupt-names : Should be the names of irq resources. Each interrupt
   uses its own interrupt name, so there should be as many interrupt names
-  as referenced interrups.
+  as referenced interrupts.
 - interrupt-controller : Identifies the node as an interrupt controller.
 - #interrupt-cells: Specifies the number of cells needed to encode an
   interrupt source.