Merge tag 'sound-4.15-rc1' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/tiwai/sound

Pull sound updates from Takashi Iwai:
 "There are no big surprising changes in this cycle, yet not too boring,
  either. The biggest change from diffstat POV is the removal of the
  legacy OSS driver codes that have been already disabled for a long
  time. This will bring a few trivial merge conflicts.

  As new features in ASoC side, there are two things: a new AC97 bus
  implementation and AMD Stony platform support. Both include the
  relevant changes shared with other subsystems, e.g. AC97 MFD changes
  and DRM AMD changes.

  Some other highlighted topics are:

   - A bunch of USB-audio drivers got the hardening against the
     malicious device accesses with a new helper code for endpoint
     sanity check

   - Lots of cleanups for ASoC Intel platform code, including support
     for their open source audio firmware

   - Continued ASoC core componentization works

   - Support for scaling MCLK with sample rate in ASoC simple-card

   - Stabler PCM hot-unplug capability, especially for ASoC usages"

* tag 'sound-4.15-rc1' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (302 commits)
  Documentation: sound: hd-audio: notes.rst
  ASoC: bcm2835: Support left/right justified and DSP modes
  ASoC: bcm2835: Enforce full symmetry
  ASoC: bcm2835: Support additional samplerates up to 384kHz
  ASoC: bcm2835: Add support for TDM modes
  ASoC: add mclk-fs support to audio graph card
  ASoC: add mclk-fs to audio graph card binding
  ASoC: rt5514: work around link error
  ASoC: rt5514: mark PM functions as __maybe_unused
  ASoC: rt5663: Check the JD status in the button pushing
  ASoC: amd: Modified DMA transfer Mechanism for Playback
  ASoC: rt5645: Wait for 400msec before concluding on value of RT5645_VENDOR_ID2
  ASoC: sun4i-codec: fixed 32bit audio capture support for H3/H2+
  ASoC: da7213: add support for DSP modes
  ASoC: sun8i-codec: Add a comment on the LRCK inversion
  ASoC: sun8i-codec: Set the BCLK divider
  ASoC: rt5663: Delay and retry reading rt5663 ID register
  ASoC: amd: use do_div rather than 64 bit division to fix 32 bit builds
  ASoC: cs42l56: Fix reset GPIO name in example DT binding
  ASoC: rt5514-spi: check irq status to schedule data copy in resume function
  ...

1 files changed, 0 insertions, 152 deletions

diff --git a/Documentation/sound/oss/CMI8330 b/Documentation/sound/oss/CMI8330
deleted file mode 100644
index 8a5fd1611c6f..000000000000
--- a/Documentation/sound/oss/CMI8330
+++ /dev/null
@@ -1,152 +0,0 @@
-Documentation for CMI 8330 (SoundPRO) 
--------------------------------------
-Alessandro Zummo <azummo@ita.flashnet.it>
-
-( Be sure to read Documentation/sound/oss/SoundPro too )
-
-
-This adapter is now directly supported by the sb driver.
-
- The only thing you have to do is to compile the kernel sound
-support as a module and to enable kernel ISAPnP support,
-as shown below.
-
-
-CONFIG_SOUND=m
-CONFIG_SOUND_SB=m
-
-CONFIG_PNP=y
-CONFIG_ISAPNP=y
-
-
-and optionally:
-
-
-CONFIG_SOUND_MPU401=m
-
- for MPU401 support.
-
-
-(I suggest you to use "make menuconfig" or "make xconfig" 
- for a more comfortable configuration editing)
-
-
-
-Then you can do
-
- modprobe sb
-
-and everything will be (hopefully) configured.
-
-You should get something similar in syslog:
-
-sb: CMI8330 detected.
-sb: CMI8330 sb base located at 0x220
-sb: CMI8330 mpu base located at 0x330
-sb: CMI8330 mail reports to Alessandro Zummo <azummo@ita.flashnet.it>
-sb: ISAPnP reports CMI 8330 SoundPRO at i/o 0x220, irq 7, dma 1,5
-
-
-
-
-The old documentation file follows for reference
-purposes.
-
-
-How to enable CMI 8330 (SOUNDPRO) soundchip on Linux
-------------------------------------------
-Stefan Laudat <Stefan.Laudat@asit.ro>
-
-[Note: The CMI 8338 is unrelated and is supported by cmpci.o]
-
-	
-	In order to use CMI8330 under Linux  you just have to use a proper isapnp.conf, a good isapnp and a little bit of patience.  I use isapnp 1.17, but
-you may get a better one I guess at http://www.roestock.demon.co.uk/isapnptools/.
-
-	Of course you will have to compile kernel sound support as module, as shown below:
-
-CONFIG_SOUND=m
-CONFIG_SOUND_OSS=m
-CONFIG_SOUND_SB=m
-CONFIG_SOUND_ADLIB=m
-CONFIG_SOUND_MPU401=m
-# Mikro$chaft sound system (kinda useful here ;))	
-CONFIG_SOUND_MSS=m
-
-	The /etc/isapnp.conf file will be:
-
-<snip below>
-
-
-(READPORT 0x0203)
-(ISOLATE PRESERVE)
-(IDENTIFY *)
-(VERBOSITY 2)
-(CONFLICT (IO FATAL)(IRQ FATAL)(DMA FATAL)(MEM FATAL)) # or WARNING
-(VERIFYLD N)
-
-
-# WSS 
-
-(CONFIGURE CMI0001/16777472 (LD 0
-(IO 0 (SIZE 8) (BASE 0x0530))
-(IO 1 (SIZE 8) (BASE 0x0388))
-(INT 0 (IRQ 7 (MODE +E)))
-(DMA 0 (CHANNEL 0))
-(NAME "CMI0001/16777472[0]{CMI8330/C3D Audio Adapter}")
-(ACT Y)
-))
-
-# MPU
-
-(CONFIGURE CMI0001/16777472 (LD 1
-(IO 0 (SIZE 2) (BASE 0x0330))
-(INT 0 (IRQ 11 (MODE +E)))
-(NAME "CMI0001/16777472[1]{CMI8330/C3D Audio Adapter}")
-(ACT Y)
-))
-
-# Joystick
-
-(CONFIGURE CMI0001/16777472 (LD 2
-(IO 0 (SIZE 8) (BASE 0x0200))
-(NAME "CMI0001/16777472[2]{CMI8330/C3D Audio Adapter}")
-(ACT Y)
-))
-
-# SoundBlaster 
- 
-(CONFIGURE CMI0001/16777472 (LD 3
-(IO 0 (SIZE 16) (BASE 0x0220))
-(INT 0 (IRQ 5 (MODE +E)))
-(DMA 0 (CHANNEL 1))
-(DMA 1 (CHANNEL 5))
-(NAME "CMI0001/16777472[3]{CMI8330/C3D Audio Adapter}")
-(ACT Y)
-))
-
-
-(WAITFORKEY)
-
-<end of snip>
-
-	The module sequence is trivial:
-
-/sbin/insmod soundcore
-/sbin/insmod sound
-/sbin/insmod uart401
-# insert this first
-/sbin/insmod ad1848 io=0x530 irq=7 dma=0 soundpro=1
-# The sb module is an alternative to the ad1848 (Microsoft Sound System)
-# Anyhow, this is full duplex and has MIDI
-/sbin/insmod sb io=0x220 dma=1 dma16=5 irq=5 mpu_io=0x330
-
-
-
-Alma Chao <elysian@ethereal.torsion.org> suggests the following in
-a /etc/modprobe.d/*conf file:
-
-alias sound ad1848
-alias synth0 opl3
-options ad1848 io=0x530 irq=7 dma=0 soundpro=1
-options opl3 io=0x388