Merge tag 'pm-4.11-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm

Pull power management updates from Rafael Wysocki:
 "The majority of changes go into the Operating Performance Points (OPP)
  framework and cpufreq this time, followed by devfreq and some
  scattered updates all over.

  The OPP changes are mostly related to switching over from RCU-based
  synchronization, that turned out to be overly complicated and
  problematic, to reference counting using krefs.

  In the cpufreq land there are core cleanups, documentation updates, a
  new driver for Broadcom BMIPS SoCs, a new cpufreq-dt sub-driver for TI
  SoCs that require special handling, ARM64 SoCs support for the qoriq
  driver, intel_pstate updates, powernv driver update and assorted
  fixes.

  The devfreq changes are mostly fixes related to the sysfs interface
  and some Exynos drivers updates.

  Apart from that, the cpuidle menu governor will support per-CPU PM QoS
  constraints for the wakeup latency now, some bugs in the wakeup IRQs
  framework are fixed, the generic power domains framework should handle
  asynchronous invocations of *noirq suspend/resume callbacks from now
  on, the analyze_suspend.py script is updated and there is a new tool
  for intel_pstate diagnostics.

  Specifics:

   - Operating Performance Points (OPP) framework fixes, cleanups and
     switch over from RCU-based synchronization to reference counting
     using krefs (Viresh Kumar, Wei Yongjun, Dave Gerlach)

   - cpufreq core cleanups and documentation updates (Viresh Kumar,
     Rafael Wysocki)

   - New cpufreq driver for Broadcom BMIPS SoCs (Markus Mayer)

   - New cpufreq-dt sub-driver for TI SoCs requiring special handling,
     like in the AM335x, AM437x, DRA7x, and AM57x families, along with
     new DT bindings for it (Dave Gerlach, Paul Gortmaker)

   - ARM64 SoCs support for the qoriq cpufreq driver (Tang Yuantian)

   - intel_pstate driver updates including a new sysfs knob to control
     the driver's operation mode and fixes related to the no_turbo sysfs
     knob and the hardware-managed P-states feature support (Rafael
     Wysocki, Srinivas Pandruvada)

   - New interface to export ultra-turbo frequencies for the powernv
     cpufreq driver (Shilpasri Bhat)

   - Assorted fixes for cpufreq drivers (Arnd Bergmann, Dan Carpenter,
     Wei Yongjun)

   - devfreq core fixes, mostly related to the sysfs interface exported
     by it (Chanwoo Choi, Chris Diamand)

   - Updates of the exynos-bus and exynos-ppmu devfreq drivers (Chanwoo
     Choi)

   - Device PM QoS extension to support CPUs and support for per-CPU
     wakeup (device resume) latency constraints in the cpuidle menu
     governor (Alex Shi)

   - Wakeup IRQs framework fixes (Grygorii Strashko)

   - Generic power domains framework update including a fix to make it
     handle asynchronous invocations of *noirq suspend/resume callbacks
     correctly (Ulf Hansson, Geert Uytterhoeven)

   - Assorted fixes and cleanups in the core suspend/hibernate code, PM
     QoS framework and x86 ACPI idle support code (Corentin Labbe, Geert
     Uytterhoeven, Geliang Tang, John Keeping, Nick Desaulniers)

   - Update of the analyze_suspend.py script is updated to version 4.5
     offering multiple improvements (Todd Brandt)

   - New tool for intel_pstate diagnostics using the pstate_sample
     tracepoint (Doug Smythies)"

* tag 'pm-4.11-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (85 commits)
  MAINTAINERS: cpufreq: add bmips-cpufreq.c
  PM / QoS: Fix memory leak on resume_latency.notifiers
  PM / Documentation: Spelling s/wrtie/write/
  PM / sleep: Fix test_suspend after sleep state rework
  cpufreq: CPPC: add ACPI_PROCESSOR dependency
  cpufreq: make ti-cpufreq explicitly non-modular
  cpufreq: Do not clear real_cpus mask on policy init
  tools/power/x86: Debug utility for intel_pstate driver
  AnalyzeSuspend: fix drag and zoom bug in javascript
  PM / wakeirq: report a wakeup_event on dedicated wekup irq
  PM / wakeirq: Fix spurious wake-up events for dedicated wakeirqs
  PM / wakeirq: Enable dedicated wakeirq for suspend
  cpufreq: dt: Don't use generic platdev driver for ti-cpufreq platforms
  cpufreq: ti: Add cpufreq driver to determine available OPPs at runtime
  Documentation: dt: add bindings for ti-cpufreq
  PM / OPP: Expose _of_get_opp_desc_node as dev_pm_opp API
  cpufreq: qoriq: Don't look at clock implementation details
  cpufreq: qoriq: add ARM64 SoCs support
  PM / Domains: Provide dummy governors if CONFIG_PM_GENERIC_DOMAINS=n
  cpufreq: brcmstb-avs-cpufreq: remove unnecessary platform_set_drvdata()
  ...

12 files changed, 543 insertions, 323 deletions

diff --git a/Documentation/ABI/testing/sysfs-class-devfreq-event b/Documentation/ABI/testing/sysfs-class-devfreq-event
new file mode 100644
index 000000000000..ceaf0f686d4a
--- /dev/null
+++ b/Documentation/ABI/testing/sysfs-class-devfreq-event
@@ -0,0 +1,25 @@
+What:		/sys/class/devfreq-event/event(x)/
+Date:		January 2017
+Contact:	Chanwoo Choi <cw00.choi@samsung.com>
+Description:
+		Provide a place in sysfs for the devfreq-event objects.
+		This allows accessing various devfreq-event specific variables.
+		The name of devfreq-event object denoted as 'event(x)' which
+		includes the unique number of 'x' for each devfreq-event object.
+
+What:		/sys/class/devfreq-event/event(x)/name
+Date:		January 2017
+Contact:	Chanwoo Choi <cw00.choi@samsung.com>
+Description:
+		The /sys/class/devfreq-event/event(x)/name attribute contains
+		the name of the devfreq-event object. This attribute is
+		read-only.
+
+What:		/sys/class/devfreq-event/event(x)/enable_count
+Date:		January 2017
+Contact:	Chanwoo Choi <cw00.choi@samsung.com>
+Description:
+		The /sys/class/devfreq-event/event(x)/enable_count attribute
+		contains the reference count to enable the devfreq-event
+		object. If the device is enabled, the value of attribute is
+		greater than zero.
diff --git a/Documentation/cpu-freq/core.txt b/Documentation/cpu-freq/core.txt
index 4bc7287806de..978463a7c81e 100644
--- a/Documentation/cpu-freq/core.txt
+++ b/Documentation/cpu-freq/core.txt
@@ -8,6 +8,8 @@
 
 		    Dominik Brodowski  <linux@brodo.de>
 		     David Kimdon <dwhedon@debian.org>
+		Rafael J. Wysocki <rafael.j.wysocki@intel.com>
+		   Viresh Kumar <viresh.kumar@linaro.org>
 
 
 
@@ -36,10 +38,11 @@ speed limits (like LCD drivers on ARM architecture). Additionally, the
 kernel "constant" loops_per_jiffy is updated on frequency changes
 here.
 
-Reference counting is done by cpufreq_get_cpu and cpufreq_put_cpu,
-which make sure that the cpufreq processor driver is correctly
-registered with the core, and will not be unloaded until
-cpufreq_put_cpu is called.
+Reference counting of the cpufreq policies is done by cpufreq_cpu_get
+and cpufreq_cpu_put, which make sure that the cpufreq driver is
+correctly registered with the core, and will not be unloaded until
+cpufreq_put_cpu is called. That also ensures that the respective cpufreq
+policy doesn't get freed while being used.
 
 2. CPUFreq notifiers
 ====================
@@ -69,18 +72,16 @@ CPUFreq policy notifier is called twice for a policy transition:
 The phase is specified in the second argument to the notifier.
 
 The third argument, a void *pointer, points to a struct cpufreq_policy
-consisting of five values: cpu, min, max, policy and max_cpu_freq. min 
-and max are the lower and upper frequencies (in kHz) of the new
-policy, policy the new policy, cpu the number of the affected CPU; and 
-max_cpu_freq the maximum supported CPU frequency. This value is given 
-for informational purposes only.
+consisting of several values, including min, max (the lower and upper
+frequencies (in kHz) of the new policy).
 
 
 2.2 CPUFreq transition notifiers
 --------------------------------
 
-These are notified twice when the CPUfreq driver switches the CPU core
-frequency and this change has any external implications.
+These are notified twice for each online CPU in the policy, when the
+CPUfreq driver switches the CPU core frequency and this change has no
+any external implications.
 
 The second argument specifies the phase - CPUFREQ_PRECHANGE or
 CPUFREQ_POSTCHANGE.
@@ -90,6 +91,7 @@ values:
 cpu	- number of the affected CPU
 old	- old frequency
 new	- new frequency
+flags	- flags of the cpufreq driver
 
 3. CPUFreq Table Generation with Operating Performance Point (OPP)
 ==================================================================
diff --git a/Documentation/cpu-freq/cpu-drivers.txt b/Documentation/cpu-freq/cpu-drivers.txt
index 772b94fde264..f71e6be26b83 100644
--- a/Documentation/cpu-freq/cpu-drivers.txt
+++ b/Documentation/cpu-freq/cpu-drivers.txt
@@ -9,6 +9,8 @@
 
 
 		    Dominik Brodowski  <linux@brodo.de>
+		Rafael J. Wysocki <rafael.j.wysocki@intel.com>
+		   Viresh Kumar <viresh.kumar@linaro.org>
 
 
 
@@ -49,49 +51,65 @@ using cpufreq_register_driver()
 
 What shall this struct cpufreq_driver contain? 
 
-cpufreq_driver.name -		The name of this driver.
+ .name - The name of this driver.
 
-cpufreq_driver.init -		A pointer to the per-CPU initialization 
-				function.
+ .init - A pointer to the per-policy initialization function.
 
-cpufreq_driver.verify -		A pointer to a "verification" function.
+ .verify - A pointer to a "verification" function.
 
-cpufreq_driver.setpolicy _or_ 
-cpufreq_driver.target/
-target_index		-	See below on the differences.
+ .setpolicy _or_ .fast_switch _or_ .target _or_ .target_index - See
+ below on the differences.
 
 And optionally
 
-cpufreq_driver.exit -		A pointer to a per-CPU cleanup
-				function called during CPU_POST_DEAD
-				phase of cpu hotplug process.
+ .flags - Hints for the cpufreq core.
 
-cpufreq_driver.stop_cpu -	A pointer to a per-CPU stop function
-				called during CPU_DOWN_PREPARE phase of
-				cpu hotplug process.
+ .driver_data - cpufreq driver specific data.
 
-cpufreq_driver.resume -		A pointer to a per-CPU resume function
-				which is called with interrupts disabled
-				and _before_ the pre-suspend frequency
-				and/or policy is restored by a call to
-				->target/target_index or ->setpolicy.
+ .resolve_freq - Returns the most appropriate frequency for a target
+ frequency. Doesn't change the frequency though.
 
-cpufreq_driver.attr -		A pointer to a NULL-terminated list of
-				"struct freq_attr" which allow to
-				export values to sysfs.
+ .get_intermediate and target_intermediate - Used to switch to stable
+ frequency while changing CPU frequency.
 
-cpufreq_driver.get_intermediate
-and target_intermediate		Used to switch to stable frequency while
-				changing CPU frequency.
+ .get - Returns current frequency of the CPU.
+
+ .bios_limit - Returns HW/BIOS max frequency limitations for the CPU.
+
+ .exit - A pointer to a per-policy cleanup function called during
+ CPU_POST_DEAD phase of cpu hotplug process.
+
+ .stop_cpu - A pointer to a per-policy stop function called during
+ CPU_DOWN_PREPARE phase of cpu hotplug process.
+
+ .suspend - A pointer to a per-policy suspend function which is called
+ with interrupts disabled and _after_ the governor is stopped for the
+ policy.
+
+ .resume - A pointer to a per-policy resume function which is called
+ with interrupts disabled and _before_ the governor is started again.
+
+ .ready - A pointer to a per-policy ready function which is called after
+ the policy is fully initialized.
+
+ .attr - A pointer to a NULL-terminated list of "struct freq_attr" which
+ allow to export values to sysfs.
+
+ .boost_enabled - If set, boost frequencies are enabled.
+
+ .set_boost - A pointer to a per-policy function to enable/disable boost
+ frequencies.
 
 
 1.2 Per-CPU Initialization
 --------------------------
 
 Whenever a new CPU is registered with the device model, or after the
-cpufreq driver registers itself, the per-CPU initialization function 
-cpufreq_driver.init is called. It takes a struct cpufreq_policy
-*policy as argument. What to do now?
+cpufreq driver registers itself, the per-policy initialization function
+cpufreq_driver.init is called if no cpufreq policy existed for the CPU.
+Note that the .init() and .exit() routines are called only once for the
+policy and not for each CPU managed by the policy. It takes a struct
+cpufreq_policy *policy as argument. What to do now?
 
 If necessary, activate the CPUfreq support on your CPU.
 
@@ -117,47 +135,45 @@ policy->governor		must contain the "default policy" for
 				cpufreq_driver.setpolicy or
 				cpufreq_driver.target/target_index is called
 				with these values.
+policy->cpus			Update this with the masks of the
+				(online + offline) CPUs that do DVFS
+				along with this CPU (i.e.  that share
+				clock/voltage rails with it).
 
 For setting some of these values (cpuinfo.min[max]_freq, policy->min[max]), the
 frequency table helpers might be helpful. See the section 2 for more information
 on them.
 
-SMP systems normally have same clock source for a group of cpus. For these the
-.init() would be called only once for the first online cpu. Here the .init()
-routine must initialize policy->cpus with mask of all possible cpus (Online +
-Offline) that share the clock. Then the core would copy this mask onto
-policy->related_cpus and will reset policy->cpus to carry only online cpus.
-
 
 1.3 verify
-------------
+----------
 
 When the user decides a new policy (consisting of
 "policy,governor,min,max") shall be set, this policy must be validated
 so that incompatible values can be corrected. For verifying these
-values, a frequency table helper and/or the
-cpufreq_verify_within_limits(struct cpufreq_policy *policy, unsigned
-int min_freq, unsigned int max_freq) function might be helpful. See
-section 2 for details on frequency table helpers.
+values cpufreq_verify_within_limits(struct cpufreq_policy *policy,
+unsigned int min_freq, unsigned int max_freq) function might be helpful.
+See section 2 for details on frequency table helpers.
 
 You need to make sure that at least one valid frequency (or operating
 range) is within policy->min and policy->max. If necessary, increase
 policy->max first, and only if this is no solution, decrease policy->min.
 
 
-1.4 target/target_index or setpolicy?
-----------------------------
+1.4 target or target_index or setpolicy or fast_switch?
+-------------------------------------------------------
 
 Most cpufreq drivers or even most cpu frequency scaling algorithms 
-only allow the CPU to be set to one frequency. For these, you use the
-->target/target_index call.
+only allow the CPU frequency to be set to predefined fixed values. For
+these, you use the ->target(), ->target_index() or ->fast_switch()
+callbacks.
 
-Some cpufreq-capable processors switch the frequency between certain
-limits on their own. These shall use the ->setpolicy call
+Some cpufreq capable processors switch the frequency between certain
+limits on their own. These shall use the ->setpolicy() callback.
 
 
 1.5. target/target_index
--------------
+------------------------
 
 The target_index call has two arguments: struct cpufreq_policy *policy,
 and unsigned int index (into the exposed frequency table).
@@ -186,9 +202,20 @@ actual frequency must be determined using the following rules:
 Here again the frequency table helper might assist you - see section 2
 for details.
 
+1.6. fast_switch
+----------------
 
-1.6 setpolicy
----------------
+This function is used for frequency switching from scheduler's context.
+Not all drivers are expected to implement it, as sleeping from within
+this callback isn't allowed. This callback must be highly optimized to
+do switching as fast as possible.
+
+This function has two arguments: struct cpufreq_policy *policy and
+unsigned int target_frequency.
+
+
+1.7 setpolicy
+-------------
 
 The setpolicy call only takes a struct cpufreq_policy *policy as
 argument. You need to set the lower limit of the in-processor or
@@ -198,7 +225,7 @@ setting when policy->policy is CPUFREQ_POLICY_PERFORMANCE, and a
 powersaving-oriented setting when CPUFREQ_POLICY_POWERSAVE. Also check
 the reference implementation in drivers/cpufreq/longrun.c
 
-1.7 get_intermediate and target_intermediate
+1.8 get_intermediate and target_intermediate
 --------------------------------------------
 
 Only for drivers with target_index() and CPUFREQ_ASYNC_NOTIFICATION unset.
@@ -222,42 +249,36 @@ failures as core would send notifications for that.
 
 As most cpufreq processors only allow for being set to a few specific
 frequencies, a "frequency table" with some functions might assist in
-some work of the processor driver. Such a "frequency table" consists
-of an array of struct cpufreq_frequency_table entries, with any value in
-"driver_data" you want to use, and the corresponding frequency in
-"frequency". At the end of the table, you need to add a
-cpufreq_frequency_table entry with frequency set to CPUFREQ_TABLE_END. And
-if you want to skip one entry in the table, set the frequency to 
-CPUFREQ_ENTRY_INVALID. The entries don't need to be in ascending
-order.
-
-By calling cpufreq_table_validate_and_show(struct cpufreq_policy *policy,
-					struct cpufreq_frequency_table *table);
-the cpuinfo.min_freq and cpuinfo.max_freq values are detected, and
-policy->min and policy->max are set to the same values. This is
-helpful for the per-CPU initialization stage.
-
-int cpufreq_frequency_table_verify(struct cpufreq_policy *policy,
-                                   struct cpufreq_frequency_table *table);
-assures that at least one valid frequency is within policy->min and
-policy->max, and all other criteria are met. This is helpful for the
-->verify call.
-
-int cpufreq_frequency_table_target(struct cpufreq_policy *policy,
-                                   unsigned int target_freq,
-                                   unsigned int relation);
-
-is the corresponding frequency table helper for the ->target
-stage. Just pass the values to this function, and this function
-returns the number of the frequency table entry which contains
-the frequency the CPU shall be set to.
+some work of the processor driver. Such a "frequency table" consists of
+an array of struct cpufreq_frequency_table entries, with driver specific
+values in "driver_data", the corresponding frequency in "frequency" and
+flags set. At the end of the table, you need to add a
+cpufreq_frequency_table entry with frequency set to CPUFREQ_TABLE_END.
+And if you want to skip one entry in the table, set the frequency to
+CPUFREQ_ENTRY_INVALID. The entries don't need to be in sorted in any
+particular order, but if they are cpufreq core will do DVFS a bit
+quickly for them as search for best match is faster.
+
+By calling cpufreq_table_validate_and_show(), the cpuinfo.min_freq and
+cpuinfo.max_freq values are detected, and policy->min and policy->max
+are set to the same values. This is helpful for the per-CPU
+initialization stage.
+
+cpufreq_frequency_table_verify() assures that at least one valid
+frequency is within policy->min and policy->max, and all other criteria
+are met. This is helpful for the ->verify call.
+
+cpufreq_frequency_table_target() is the corresponding frequency table
+helper for the ->target stage. Just pass the values to this function,
+and this function returns the of the frequency table entry which
+contains the frequency the CPU shall be set to.
 
 The following macros can be used as iterators over cpufreq_frequency_table:
 
 cpufreq_for_each_entry(pos, table) - iterates over all entries of frequency
 table.
 
-cpufreq-for_each_valid_entry(pos, table) - iterates over all entries,
+cpufreq_for_each_valid_entry(pos, table) - iterates over all entries,
 excluding CPUFREQ_ENTRY_INVALID frequencies.
 Use arguments "pos" - a cpufreq_frequency_table * as a loop cursor and
 "table" - the cpufreq_frequency_table * you want to iterate over.
diff --git a/Documentation/cpu-freq/cpufreq-stats.txt b/Documentation/cpu-freq/cpufreq-stats.txt
index 3c355f6ad834..2bbe207354ed 100644
--- a/Documentation/cpu-freq/cpufreq-stats.txt
+++ b/Documentation/cpu-freq/cpufreq-stats.txt
@@ -34,10 +34,10 @@ cpufreq stats provides following statistics (explained in detail below).
 -  total_trans
 -  trans_table
 
-All the statistics will be from the time the stats driver has been inserted 
-to the time when a read of a particular statistic is done. Obviously, stats 
-driver will not have any information about the frequency transitions before
-the stats driver insertion.
+All the statistics will be from the time the stats driver has been inserted
+(or the time the stats were reset) to the time when a read of a particular
+statistic is done. Obviously, stats driver will not have any information
+about the frequency transitions before the stats driver insertion.
 
 --------------------------------------------------------------------------------
 <mysystem>:/sys/devices/system/cpu/cpu0/cpufreq/stats # ls -l
@@ -110,25 +110,13 @@ Config Main Menu
 		CPU Frequency scaling  --->
 			[*] CPU Frequency scaling
 			[*]   CPU frequency translation statistics
-			[*]     CPU frequency translation statistics details
 
 
 "CPU Frequency scaling" (CONFIG_CPU_FREQ) should be enabled to configure
 cpufreq-stats.
 
 "CPU frequency translation statistics" (CONFIG_CPU_FREQ_STAT) provides the
-basic statistics which includes time_in_state and total_trans.
+statistics which includes time_in_state, total_trans and trans_table.
 
-"CPU frequency translation statistics details" (CONFIG_CPU_FREQ_STAT_DETAILS)
-provides fine grained cpufreq stats by trans_table. The reason for having a
-separate config option for trans_table is:
-- trans_table goes against the traditional /sysfs rule of one value per
-  interface. It provides a whole bunch of value in a 2 dimensional matrix
-  form.
-
-Once these two options are enabled and your CPU supports cpufrequency, you
+Once this option is enabled and your CPU supports cpufrequency, you
 will be able to see the CPU frequency statistics in /sysfs.
-
-
-
-
diff --git a/Documentation/cpu-freq/governors.txt b/Documentation/cpu-freq/governors.txt
index c15aa75f5227..61b3184b6c24 100644
--- a/Documentation/cpu-freq/governors.txt
+++ b/Documentation/cpu-freq/governors.txt
@@ -10,6 +10,8 @@
 
 		    Dominik Brodowski  <linux@brodo.de>
             some additions and corrections by Nico Golde <nico@ngolde.de>
+		Rafael J. Wysocki <rafael.j.wysocki@intel.com>
+		   Viresh Kumar <viresh.kumar@linaro.org>
 
 
 
@@ -28,32 +30,27 @@ Contents:
 2.3  Userspace
 2.4  Ondemand
 2.5  Conservative
+2.6  Schedutil
 
 3.   The Governor Interface in the CPUfreq Core
 
+4.   References
 
 
 1. What Is A CPUFreq Governor?
 ==============================
 
 Most cpufreq drivers (except the intel_pstate and longrun) or even most
-cpu frequency scaling algorithms only offer the CPU to be set to one
-frequency. In order to offer dynamic frequency scaling, the cpufreq
-core must be able to tell these drivers of a "target frequency". So
-these specific drivers will be transformed to offer a "->target/target_index"
-call instead of the existing "->setpolicy" call. For "longrun", all
-stays the same, though.
+cpu frequency scaling algorithms only allow the CPU frequency to be set
+to predefined fixed values.  In order to offer dynamic frequency
+scaling, the cpufreq core must be able to tell these drivers of a
+"target frequency". So these specific drivers will be transformed to
+offer a "->target/target_index/fast_switch()" call instead of the
+"->setpolicy()" call. For set_policy drivers, all stays the same,
+though.
 
 How to decide what frequency within the CPUfreq policy should be used?
-That's done using "cpufreq governors". Two are already in this patch
--- they're the already existing "powersave" and "performance" which
-set the frequency statically to the lowest or highest frequency,
-respectively. At least two more such governors will be ready for
-addition in the near future, but likely many more as there are various
-different theories and models about dynamic frequency scaling
-around. Using such a generic interface as cpufreq offers to scaling
-governors, these can be tested extensively, and the best one can be
-selected for each specific use.
+That's done using "cpufreq governors".
 
 Basically, it's the following flow graph:
 
@@ -71,7 +68,7 @@ CPU can be set to switch independently	 |	   CPU can only be set
 		    /			       the limits of policy->{min,max}
 		   /			            \
 		  /				     \
-	Using the ->setpolicy call,		 Using the ->target/target_index call,
+	Using the ->setpolicy call,		 Using the ->target/target_index/fast_switch call,
 	    the limits and the			  the frequency closest
 	     "policy" is set.			  to target_freq is set.
 						  It is assured that it
@@ -109,114 +106,159 @@ directory.
 2.4 Ondemand
 ------------
 
-The CPUfreq governor "ondemand" sets the CPU depending on the
-current usage. To do this the CPU must have the capability to
-switch the frequency very quickly.  There are a number of sysfs file
-accessible parameters:
-
-sampling_rate: measured in uS (10^-6 seconds), this is how often you
-want the kernel to look at the CPU usage and to make decisions on
-what to do about the frequency.  Typically this is set to values of
-around '10000' or more. It's default value is (cmp. with users-guide.txt):
-transition_latency * 1000
-Be aware that transition latency is in ns and sampling_rate is in us, so you
-get the same sysfs value by default.
-Sampling rate should always get adjusted considering the transition latency
-To set the sampling rate 750 times as high as the transition latency
-in the bash (as said, 1000 is default), do:
-echo `$(($(cat cpuinfo_transition_latency) * 750 / 1000)) \
-    >ondemand/sampling_rate
-
-sampling_rate_min:
-The sampling rate is limited by the HW transition latency:
-transition_latency * 100
-Or by kernel restrictions:
-If CONFIG_NO_HZ_COMMON is set, the limit is 10ms fixed.
-If CONFIG_NO_HZ_COMMON is not set or nohz=off boot parameter is used, the
-limits depend on the CONFIG_HZ option:
-HZ=1000: min=20000us  (20ms)
-HZ=250:  min=80000us  (80ms)
-HZ=100:  min=200000us (200ms)
-The highest value of kernel and HW latency restrictions is shown and
-used as the minimum sampling rate.
-
-up_threshold: defines what the average CPU usage between the samplings
-of 'sampling_rate' needs to be for the kernel to make a decision on
-whether it should increase the frequency.  For example when it is set
-to its default value of '95' it means that between the checking
-intervals the CPU needs to be on average more than 95% in use to then
-decide that the CPU frequency needs to be increased.  
-
-ignore_nice_load: this parameter takes a value of '0' or '1'. When
-set to '0' (its default), all processes are counted towards the
-'cpu utilisation' value.  When set to '1', the processes that are
-run with a 'nice' value will not count (and thus be ignored) in the
-overall usage calculation.  This is useful if you are running a CPU
-intensive calculation on your laptop that you do not care how long it
-takes to complete as you can 'nice' it and prevent it from taking part
-in the deciding process of whether to increase your CPU frequency.
-
-sampling_down_factor: this parameter controls the rate at which the
-kernel makes a decision on when to decrease the frequency while running
-at top speed. When set to 1 (the default) decisions to reevaluate load
-are made at the same interval regardless of current clock speed. But
-when set to greater than 1 (e.g. 100) it acts as a multiplier for the
-scheduling interval for reevaluating load when the CPU is at its top
-speed due to high load. This improves performance by reducing the overhead
-of load evaluation and helping the CPU stay at its top speed when truly
-busy, rather than shifting back and forth in speed. This tunable has no
-effect on behavior at lower speeds/lower CPU loads.
-
-powersave_bias: this parameter takes a value between 0 to 1000. It
-defines the percentage (times 10) value of the target frequency that
-will be shaved off of the target. For example, when set to 100 -- 10%,
-when ondemand governor would have targeted 1000 MHz, it will target
-1000 MHz - (10% of 1000 MHz) = 900 MHz instead. This is set to 0
-(disabled) by default.
-When AMD frequency sensitivity powersave bias driver --
-drivers/cpufreq/amd_freq_sensitivity.c is loaded, this parameter
-defines the workload frequency sensitivity threshold in which a lower
-frequency is chosen instead of ondemand governor's original target.
-The frequency sensitivity is a hardware reported (on AMD Family 16h
-Processors and above) value between 0 to 100% that tells software how
-the performance of the workload running on a CPU will change when
-frequency changes. A workload with sensitivity of 0% (memory/IO-bound)
-will not perform any better on higher core frequency, whereas a
-workload with sensitivity of 100% (CPU-bound) will perform better
-higher the frequency. When the driver is loaded, this is set to 400
-by default -- for CPUs running workloads with sensitivity value below
-40%, a lower frequency is chosen. Unloading the driver or writing 0
-will disable this feature.
+The CPUfreq governor "ondemand" sets the CPU frequency depending on the
+current system load. Load estimation is triggered by the scheduler
+through the update_util_data->func hook; when triggered, cpufreq checks
+the CPU-usage statistics over the last period and the governor sets the
+CPU accordingly.  The CPU must have the capability to switch the
+frequency very quickly.
+
+Sysfs files:
+
+* sampling_rate:
+
+  Measured in uS (10^-6 seconds), this is how often you want the kernel
+  to look at the CPU usage and to make decisions on what to do about the
+  frequency.  Typically this is set to values of around '10000' or more.
+  It's default value is (cmp. with users-guide.txt): transition_latency
+  * 1000.  Be aware that transition latency is in ns and sampling_rate
+  is in us, so you get the same sysfs value by default.  Sampling rate
+  should always get adjusted considering the transition latency to set
+  the sampling rate 750 times as high as the transition latency in the
+  bash (as said, 1000 is default), do:
+
+  $ echo `$(($(cat cpuinfo_transition_latency) * 750 / 1000)) > ondemand/sampling_rate
+
+* sampling_rate_min:
+
+  The sampling rate is limited by the HW transition latency:
+  transition_latency * 100
+
+  Or by kernel restrictions:
+  - If CONFIG_NO_HZ_COMMON is set, the limit is 10ms fixed.
+  - If CONFIG_NO_HZ_COMMON is not set or nohz=off boot parameter is
+    used, the limits depend on the CONFIG_HZ option:
+    HZ=1000: min=20000us  (20ms)
+    HZ=250:  min=80000us  (80ms)
+    HZ=100:  min=200000us (200ms)
+
+  The highest value of kernel and HW latency restrictions is shown and
+  used as the minimum sampling rate.
+
+* up_threshold:
+
+  This defines what the average CPU usage between the samplings of
+  'sampling_rate' needs to be for the kernel to make a decision on
+  whether it should increase the frequency.  For example when it is set
+  to its default value of '95' it means that between the checking
+  intervals the CPU needs to be on average more than 95% in use to then
+  decide that the CPU frequency needs to be increased.
+
+* ignore_nice_load:
+
+  This parameter takes a value of '0' or '1'. When set to '0' (its
+  default), all processes are counted towards the 'cpu utilisation'
+  value.  When set to '1', the processes that are run with a 'nice'
+  value will not count (and thus be ignored) in the overall usage
+  calculation.  This is useful if you are running a CPU intensive
+  calculation on your laptop that you do not care how long it takes to
+  complete as you can 'nice' it and prevent it from taking part in the
+  deciding process of whether to increase your CPU frequency.
+
+* sampling_down_factor:
+
+  This parameter controls the rate at which the kernel makes a decision
+  on when to decrease the frequency while running at top speed. When set
+  to 1 (the default) decisions to reevaluate load are made at the same
+  interval regardless of current clock speed. But when set to greater
+  than 1 (e.g. 100) it acts as a multiplier for the scheduling interval
+  for reevaluating load when the CPU is at its top speed due to high
+  load. This improves performance by reducing the overhead of load
+  evaluation and helping the CPU stay at its top speed when truly busy,
+  rather than shifting back and forth in speed. This tunable has no
+  effect on behavior at lower speeds/lower CPU loads.
+
+* powersave_bias:
+
+  This parameter takes a value between 0 to 1000. It defines the
+  percentage (times 10) value of the target frequency that will be
+  shaved off of the target. For example, when set to 100 -- 10%, when
+  ondemand governor would have targeted 1000 MHz, it will target
+  1000 MHz - (10% of 1000 MHz) = 900 MHz instead. This is set to 0
+  (disabled) by default.
+
+  When AMD frequency sensitivity powersave bias driver --
+  drivers/cpufreq/amd_freq_sensitivity.c is loaded, this parameter
+  defines the workload frequency sensitivity threshold in which a lower
+  frequency is chosen instead of ondemand governor's original target.
+  The frequency sensitivity is a hardware reported (on AMD Family 16h
+  Processors and above) value between 0 to 100% that tells software how
+  the performance of the workload running on a CPU will change when
+  frequency changes. A workload with sensitivity of 0% (memory/IO-bound)
+  will not perform any better on higher core frequency, whereas a
+  workload with sensitivity of 100% (CPU-bound) will perform better
+  higher the frequency. When the driver is loaded, this is set to 400 by
+  default -- for CPUs running workloads with sensitivity value below
+  40%, a lower frequency is chosen. Unloading the driver or writing 0
+  will disable this feature.
 
 
 2.5 Conservative
 ----------------
 
 The CPUfreq governor "conservative", much like the "ondemand"
-governor, sets the CPU depending on the current usage.  It differs in
-behaviour in that it gracefully increases and decreases the CPU speed
-rather than jumping to max speed the moment there is any load on the
-CPU.  This behaviour more suitable in a battery powered environment.
-The governor is tweaked in the same manner as the "ondemand" governor
-through sysfs with the addition of:
-
-freq_step: this describes what percentage steps the cpu freq should be
-increased and decreased smoothly by.  By default the cpu frequency will
-increase in 5% chunks of your maximum cpu frequency.  You can change this
-value to anywhere between 0 and 100 where '0' will effectively lock your
-CPU at a speed regardless of its load whilst '100' will, in theory, make
-it behave identically to the "ondemand" governor.
-
-down_threshold: same as the 'up_threshold' found for the "ondemand"
-governor but for the opposite direction.  For example when set to its
-default value of '20' it means that if the CPU usage needs to be below
-20% between samples to have the frequency decreased.
-
-sampling_down_factor: similar functionality as in "ondemand" governor.
-But in "conservative", it controls the rate at which the kernel makes
-a decision on when to decrease the frequency while running in any
-speed. Load for frequency increase is still evaluated every
-sampling rate.
+governor, sets the CPU frequency depending on the current usage.  It
+differs in behaviour in that it gracefully increases and decreases the
+CPU speed rather than jumping to max speed the moment there is any load
+on the CPU. This behaviour is more suitable in a battery powered
+environment.  The governor is tweaked in the same manner as the
+"ondemand" governor through sysfs with the addition of:
+
+* freq_step:
+
+  This describes what percentage steps the cpu freq should be increased
+  and decreased smoothly by.  By default the cpu frequency will increase
+  in 5% chunks of your maximum cpu frequency.  You can change this value
+  to anywhere between 0 and 100 where '0' will effectively lock your CPU
+  at a speed regardless of its load whilst '100' will, in theory, make
+  it behave identically to the "ondemand" governor.
+
+* down_threshold:
+
+  Same as the 'up_threshold' found for the "ondemand" governor but for
+  the opposite direction.  For example when set to its default value of
+  '20' it means that if the CPU usage needs to be below 20% between
+  samples to have the frequency decreased.
+
+* sampling_down_factor:
+
+  Similar functionality as in "ondemand" governor.  But in
+  "conservative", it controls the rate at which the kernel makes a
+  decision on when to decrease the frequency while running in any speed.
+  Load for frequency increase is still evaluated every sampling rate.
+
+
+2.6 Schedutil
+-------------
+
+The "schedutil" governor aims at better integration with the Linux
+kernel scheduler.  Load estimation is achieved through the scheduler's
+Per-Entity Load Tracking (PELT) mechanism, which also provides
+information about the recent load [1].  This governor currently does
+load based DVFS only for tasks managed by CFS. RT and DL scheduler tasks
+are always run at the highest frequency.  Unlike all the other
+governors, the code is located under the kernel/sched/ directory.
+
+Sysfs files:
+
+* rate_limit_us:
+
+  This contains a value in microseconds. The governor waits for
+  rate_limit_us time before reevaluating the load again, after it has
+  evaluated the load once.
+
+For an in-depth comparison with the other governors refer to [2].
+
 
 3. The Governor Interface in the CPUfreq Core
 =============================================
@@ -225,26 +267,10 @@ A new governor must register itself with the CPUfreq core using
 "cpufreq_register_governor". The struct cpufreq_governor, which has to
 be passed to that function, must contain the following values:
 
-governor->name -	    A unique name for this governor
-governor->governor -	    The governor callback function
-governor->owner	-	    .THIS_MODULE for the governor module (if 
-			    appropriate)
-
-The governor->governor callback is called with the current (or to-be-set)
-cpufreq_policy struct for that CPU, and an unsigned int event. The
-following events are currently defined:
-
-CPUFREQ_GOV_START:   This governor shall start its duty for the CPU
-		     policy->cpu
-CPUFREQ_GOV_STOP:    This governor shall end its duty for the CPU
-		     policy->cpu
-CPUFREQ_GOV_LIMITS:  The limits for CPU policy->cpu have changed to
-		     policy->min and policy->max.
-
-If you need other "events" externally of your driver, _only_ use the
-cpufreq_governor_l(unsigned int cpu, unsigned int event) call to the
-CPUfreq core to ensure proper locking.
+governor->name - A unique name for this governor.
+governor->owner - .THIS_MODULE for the governor module (if appropriate).
 
+plus a set of hooks to the functions implementing the governor's logic.
 
 The CPUfreq governor may call the CPU processor driver using one of
 these two functions:
@@ -258,12 +284,18 @@ int __cpufreq_driver_target(struct cpufreq_policy *policy,
                                    unsigned int relation);
 
 target_freq must be within policy->min and policy->max, of course.
-What's the difference between these two functions? When your governor
-still is in a direct code path of a call to governor->governor, the
-per-CPU cpufreq lock is still held in the cpufreq core, and there's
-no need to lock it again (in fact, this would cause a deadlock). So
-use __cpufreq_driver_target only in these cases. In all other cases 
-(for example, when there's a "daemonized" function that wakes up 
-every second), use cpufreq_driver_target to lock the cpufreq per-CPU
-lock before the command is passed to the cpufreq processor driver.
+What's the difference between these two functions? When your governor is
+in a direct code path of a call to governor callbacks, like
+governor->start(), the policy->rwsem is still held in the cpufreq core,
+and there's no need to lock it again (in fact, this would cause a
+deadlock). So use __cpufreq_driver_target only in these cases. In all
+other cases (for example, when there's a "daemonized" function that
+wakes up every second), use cpufreq_driver_target to take policy->rwsem
+before the command is passed to the cpufreq driver.
+
+4. References
+=============
+
+[1] Per-entity load tracking: https://lwn.net/Articles/531853/
+[2] Improvements in CPU frequency management: https://lwn.net/Articles/682391/
 
diff --git a/Documentation/cpu-freq/index.txt b/Documentation/cpu-freq/index.txt
index dc024ab4054f..ef1d39247b05 100644
--- a/Documentation/cpu-freq/index.txt
+++ b/Documentation/cpu-freq/index.txt
@@ -18,16 +18,29 @@
 
 Documents in this directory:
 ----------------------------
+
+amd-powernow.txt -	AMD powernow driver specific file.
+
+boost.txt -		Frequency boosting support.
+
 core.txt	-	General description of the CPUFreq core and
-			of CPUFreq notifiers
+			of CPUFreq notifiers.
+
+cpu-drivers.txt -	How to implement a new cpufreq processor driver.
 
-cpu-drivers.txt -	How to implement a new cpufreq processor driver
+cpufreq-nforce2.txt -	nVidia nForce2 platform specific file.
+
+cpufreq-stats.txt -	General description of sysfs cpufreq stats.
 
 governors.txt	-	What are cpufreq governors and how to
 			implement them?
 
 index.txt	-	File index, Mailing list and Links (this document)
 
+intel-pstate.txt -	Intel pstate cpufreq driver specific file.
+
+pcc-cpufreq.txt -	PCC cpufreq driver specific file.
+
 user-guide.txt	-	User Guide to CPUFreq
 
 
@@ -35,9 +48,7 @@ Mailing List
 ------------
 There is a CPU frequency changing CVS commit and general list where
 you can report bugs, problems or submit patches. To post a message,
-send an email to linux-pm@vger.kernel.org, to subscribe go to
-http://vger.kernel.org/vger-lists.html#linux-pm and follow the
-instructions there.
+send an email to linux-pm@vger.kernel.org.
 
 Links
 -----
@@ -48,7 +59,7 @@ how to access the CVS repository:
 * http://cvs.arm.linux.org.uk/
 
 the CPUFreq Mailing list:
-* http://vger.kernel.org/vger-lists.html#cpufreq
+* http://vger.kernel.org/vger-lists.html#linux-pm
 
 Clock and voltage scaling for the SA-1100:
 * http://www.lartmaker.nl/projects/scaling
diff --git a/Documentation/cpu-freq/intel-pstate.txt b/Documentation/cpu-freq/intel-pstate.txt
index 1953994ef5e6..3fdcdfd968ba 100644
--- a/Documentation/cpu-freq/intel-pstate.txt
+++ b/Documentation/cpu-freq/intel-pstate.txt
@@ -85,6 +85,21 @@ Sysfs will show :
 Refer to "Intel® 64 and IA-32 Architectures Software Developer’s Manual
 Volume 3: System Programming Guide" to understand ratios.
 
+There is one more sysfs attribute in /sys/devices/system/cpu/intel_pstate/
+that can be used for controlling the operation mode of the driver:
+
+      status: Three settings are possible:
+      "off"     - The driver is not in use at this time.
+      "active"  - The driver works as a P-state governor (default).
+      "passive" - The driver works as a regular cpufreq one and collaborates
+                  with the generic cpufreq governors (it sets P-states as
+                  requested by those governors).
+      The current setting is returned by reads from this attribute.  Writing one
+      of the above strings to it changes the operation mode as indicated by that
+      string, if possible.  If HW-managed P-states (HWP) are enabled, it is not
+      possible to change the driver's operation mode and attempts to write to
+      this attribute will fail.
+
 cpufreq sysfs for Intel P-State
 
 Since this driver registers with cpufreq, cpufreq sysfs is also presented.
diff --git a/Documentation/cpu-freq/user-guide.txt b/Documentation/cpu-freq/user-guide.txt
index 109e97bbab77..107f6fdd7d14 100644
--- a/Documentation/cpu-freq/user-guide.txt
+++ b/Documentation/cpu-freq/user-guide.txt
@@ -18,7 +18,7 @@
 Contents:
 ---------
 1. Supported Architectures and Processors
-1.1 ARM
+1.1 ARM and ARM64
 1.2 x86
 1.3 sparc64
 1.4 ppc
@@ -37,16 +37,10 @@ Contents:
 1. Supported Architectures and Processors
 =========================================
 
-1.1 ARM
--------
-
-The following ARM processors are supported by cpufreq:
-
-ARM Integrator
-ARM-SA1100
-ARM-SA1110
-Intel PXA
+1.1 ARM and ARM64
+-----------------
 
+Almost all ARM and ARM64 platforms support CPU frequency scaling.
 
 1.2 x86
 -------
@@ -69,6 +63,7 @@ Transmeta Crusoe
 Transmeta Efficeon
 VIA Cyrix 3 / C3
 various processors on some ACPI 2.0-compatible systems [*]
+And many more
 
 [*] Only if "ACPI Processor Performance States" are available
 to the ACPI<->BIOS interface.
@@ -147,10 +142,19 @@ mounted it at /sys, the cpufreq interface is located in a subdirectory
 "cpufreq" within the cpu-device directory
 (e.g. /sys/devices/system/cpu/cpu0/cpufreq/ for the first CPU).
 
+affected_cpus :			List of Online CPUs that require software
+				coordination of frequency.
+
+cpuinfo_cur_freq :		Current frequency of the CPU as obtained from
+				the hardware, in KHz. This is the frequency
+				the CPU actually runs at.
+
 cpuinfo_min_freq :		this file shows the minimum operating
 				frequency the processor can run at(in kHz) 
+
 cpuinfo_max_freq :		this file shows the maximum operating
 				frequency the processor can run at(in kHz) 
+
 cpuinfo_transition_latency	The time it takes on this CPU to
 				switch between two frequencies in nano
 				seconds. If unknown or known to be
@@ -163,25 +167,30 @@ cpuinfo_transition_latency	The time it takes on this CPU to
 				userspace daemon. Make sure to not
 				switch the frequency too often
 				resulting in performance loss.
-scaling_driver :		this file shows what cpufreq driver is
-				used to set the frequency on this CPU
+
+related_cpus :			List of Online + Offline CPUs that need software
+				coordination of frequency.
+
+scaling_available_frequencies : List of available frequencies, in KHz.
 
 scaling_available_governors :	this file shows the CPUfreq governors
 				available in this kernel. You can see the
 				currently activated governor in
 
+scaling_cur_freq :		Current frequency of the CPU as determined by
+				the governor and cpufreq core, in KHz. This is
+				the frequency the kernel thinks the CPU runs
+				at.
+
+scaling_driver :		this file shows what cpufreq driver is
+				used to set the frequency on this CPU
+
 scaling_governor,		and by "echoing" the name of another
 				governor you can change it. Please note
 				that some governors won't load - they only
 				work on some specific architectures or
 				processors.
 
-cpuinfo_cur_freq :		Current frequency of the CPU as obtained from
-				the hardware, in KHz. This is the frequency
-				the CPU actually runs at.
-
-scaling_available_frequencies : List of available frequencies, in KHz.
-
 scaling_min_freq and
 scaling_max_freq		show the current "policy limits" (in
 				kHz). By echoing new values into these
@@ -190,16 +199,11 @@ scaling_max_freq		show the current "policy limits" (in
 				first set scaling_max_freq, then
 				scaling_min_freq.
 
-affected_cpus :			List of Online CPUs that require software
-				coordination of frequency.
-
-related_cpus :			List of Online + Offline CPUs that need software
-				coordination of frequency.
-
-scaling_cur_freq :		Current frequency of the CPU as determined by
-				the governor and cpufreq core, in KHz. This is
-				the frequency the kernel thinks the CPU runs
-				at.
+scaling_setspeed		This can be read to get the currently programmed
+				value by the governor. This can be written to
+				change the current frequency for a group of
+				CPUs, represented by a policy. This is supported
+				currently only by the userspace governor.
 
 bios_limit :			If the BIOS tells the OS to limit a CPU to
 				lower frequencies, the user can read out the
diff --git a/Documentation/devicetree/bindings/cpufreq/ti-cpufreq.txt b/Documentation/devicetree/bindings/cpufreq/ti-cpufreq.txt
new file mode 100644
index 000000000000..ba0e15ad5bd9
--- /dev/null
+++ b/Documentation/devicetree/bindings/cpufreq/ti-cpufreq.txt
@@ -0,0 +1,128 @@
+TI CPUFreq and OPP bindings
+================================
+
+Certain TI SoCs, like those in the am335x, am437x, am57xx, and dra7xx
+families support different OPPs depending on the silicon variant in use.
+The ti-cpufreq driver can use revision and an efuse value from the SoC to
+provide the OPP framework with supported hardware information. This is
+used to determine which OPPs from the operating-points-v2 table get enabled
+when it is parsed by the OPP framework.
+
+Required properties:
+--------------------
+In 'cpus' nodes:
+- operating-points-v2: Phandle to the operating-points-v2 table to use.
+
+In 'operating-points-v2' table:
+- compatible: Should be
+	- 'operating-points-v2-ti-cpu' for am335x, am43xx, and dra7xx/am57xx SoCs
+- syscon: A phandle pointing to a syscon node representing the control module
+	  register space of the SoC.
+
+Optional properties:
+--------------------
+For each opp entry in 'operating-points-v2' table:
+- opp-supported-hw: Two bitfields indicating:
+	1. Which revision of the SoC the OPP is supported by
+	2. Which eFuse bits indicate this OPP is available
+
+	A bitwise AND is performed against these values and if any bit
+	matches, the OPP gets enabled.
+
+Example:
+--------
+
+/* From arch/arm/boot/dts/am33xx.dtsi */
+cpus {
+	#address-cells = <1>;
+	#size-cells = <0>;
+	cpu@0 {
+		compatible = "arm,cortex-a8";
+		device_type = "cpu";
+		reg = <0>;
+
+		operating-points-v2 = <&cpu0_opp_table>;
+
+		clocks = <&dpll_mpu_ck>;
+		clock-names = "cpu";
+
+		clock-latency = <300000>; /* From omap-cpufreq driver */
+	};
+};
+
+/*
+ * cpu0 has different OPPs depending on SoC revision and some on revisions
+ * 0x2 and 0x4 have eFuse bits that indicate if they are available or not
+ */
+cpu0_opp_table: opp-table {
+	compatible = "operating-points-v2-ti-cpu";
+	syscon = <&scm_conf>;
+
+	/*
+	 * The three following nodes are marked with opp-suspend
+	 * because they can not be enabled simultaneously on a
+	 * single SoC.
+	 */
+	opp50@300000000 {
+		opp-hz = /bits/ 64 <300000000>;
+		opp-microvolt = <950000 931000 969000>;
+		opp-supported-hw = <0x06 0x0010>;
+		opp-suspend;
+	};
+
+	opp100@275000000 {
+		opp-hz = /bits/ 64 <275000000>;
+		opp-microvolt = <1100000 1078000 1122000>;
+		opp-supported-hw = <0x01 0x00FF>;
+		opp-suspend;
+	};
+
+	opp100@300000000 {
+		opp-hz = /bits/ 64 <300000000>;
+		opp-microvolt = <1100000 1078000 1122000>;
+		opp-supported-hw = <0x06 0x0020>;
+		opp-suspend;
+	};
+
+	opp100@500000000 {
+		opp-hz = /bits/ 64 <500000000>;
+		opp-microvolt = <1100000 1078000 1122000>;
+		opp-supported-hw = <0x01 0xFFFF>;
+	};
+
+	opp100@600000000 {
+		opp-hz = /bits/ 64 <600000000>;
+		opp-microvolt = <1100000 1078000 1122000>;
+		opp-supported-hw = <0x06 0x0040>;
+	};
+
+	opp120@600000000 {
+		opp-hz = /bits/ 64 <600000000>;
+		opp-microvolt = <1200000 1176000 1224000>;
+		opp-supported-hw = <0x01 0xFFFF>;
+	};
+
+	opp120@720000000 {
+		opp-hz = /bits/ 64 <720000000>;
+		opp-microvolt = <1200000 1176000 1224000>;
+		opp-supported-hw = <0x06 0x0080>;
+	};
+
+	oppturbo@720000000 {
+		opp-hz = /bits/ 64 <720000000>;
+		opp-microvolt = <1260000 1234800 1285200>;
+		opp-supported-hw = <0x01 0xFFFF>;
+	};
+
+	oppturbo@800000000 {
+		opp-hz = /bits/ 64 <800000000>;
+		opp-microvolt = <1260000 1234800 1285200>;
+		opp-supported-hw = <0x06 0x0100>;
+	};
+
+	oppnitro@1000000000 {
+		opp-hz = /bits/ 64 <1000000000>;
+		opp-microvolt = <1325000 1298500 1351500>;
+		opp-supported-hw = <0x04 0x0200>;
+	};
+};
diff --git a/Documentation/devicetree/bindings/devfreq/exynos-bus.txt b/Documentation/devicetree/bindings/devfreq/exynos-bus.txt
index d3ec8e676b6b..d085ef90d27c 100644
--- a/Documentation/devicetree/bindings/devfreq/exynos-bus.txt
+++ b/Documentation/devicetree/bindings/devfreq/exynos-bus.txt
@@ -123,6 +123,20 @@ Detailed correlation between sub-blocks and power line according to Exynos SoC:
 		|--- FSYS
 		|--- FSYS2
 
+- In case of Exynos5433, there is VDD_INT power line as following:
+	VDD_INT |--- G2D (parent device)
+		|--- MSCL
+		|--- GSCL
+		|--- JPEG
+		|--- MFC
+		|--- HEVC
+		|--- BUS0
+		|--- BUS1
+		|--- BUS2
+		|--- PERIS (Fixed clock rate)
+		|--- PERIC (Fixed clock rate)
+		|--- FSYS  (Fixed clock rate)
+
 Example1:
 	Show the AXI buses of Exynos3250 SoC. Exynos3250 divides the buses to
 	power line (regulator). The MIF (Memory Interface) AXI bus is used to
diff --git a/Documentation/power/opp.txt b/Documentation/power/opp.txt
index c6279c2be47c..0c007e250cd1 100644
--- a/Documentation/power/opp.txt
+++ b/Documentation/power/opp.txt
@@ -79,22 +79,6 @@ dependent subsystems such as cpufreq are left to the discretion of the SoC
 specific framework which uses the OPP library. Similar care needs to be taken
 care to refresh the cpufreq table in cases of these operations.
 
-WARNING on OPP List locking mechanism:
--------------------------------------------------
-OPP library uses RCU for exclusivity. RCU allows the query functions to operate
-in multiple contexts and this synchronization mechanism is optimal for a read
-intensive operations on data structure as the OPP library caters to.
-
-To ensure that the data retrieved are sane, the users such as SoC framework
-should ensure that the section of code operating on OPP queries are locked
-using RCU read locks. The opp_find_freq_{exact,ceil,floor},
-opp_get_{voltage, freq, opp_count} fall into this category.
-
-opp_{add,enable,disable} are updaters which use mutex and implement it's own
-RCU locking mechanisms. These functions should *NOT* be called under RCU locks
-and other contexts that prevent blocking functions in RCU or mutex operations
-from working.
-
 2. Initial OPP List Registration
 ================================
 The SoC implementation calls dev_pm_opp_add function iteratively to add OPPs per
@@ -137,15 +121,18 @@ functions return the matching pointer representing the opp if a match is
 found, else returns error. These errors are expected to be handled by standard
 error checks such as IS_ERR() and appropriate actions taken by the caller.
 
+Callers of these functions shall call dev_pm_opp_put() after they have used the
+OPP. Otherwise the memory for the OPP will never get freed and result in
+memleak.
+
 dev_pm_opp_find_freq_exact - Search for an OPP based on an *exact* frequency and
 	availability. This function is especially useful to enable an OPP which
 	is not available by default.
 	Example: In a case when SoC framework detects a situation where a
 	higher frequency could be made available, it can use this function to
 	find the OPP prior to call the dev_pm_opp_enable to actually make it available.
-	 rcu_read_lock();
 	 opp = dev_pm_opp_find_freq_exact(dev, 1000000000, false);
-	 rcu_read_unlock();
+	 dev_pm_opp_put(opp);
 	 /* dont operate on the pointer.. just do a sanity check.. */
 	 if (IS_ERR(opp)) {
 		pr_err("frequency not disabled!\n");
@@ -163,9 +150,8 @@ dev_pm_opp_find_freq_floor - Search for an available OPP which is *at most* the
 	frequency.
 	Example: To find the highest opp for a device:
 	 freq = ULONG_MAX;
-	 rcu_read_lock();
-	 dev_pm_opp_find_freq_floor(dev, &freq);
-	 rcu_read_unlock();
+	 opp = dev_pm_opp_find_freq_floor(dev, &freq);
+	 dev_pm_opp_put(opp);
 
 dev_pm_opp_find_freq_ceil - Search for an available OPP which is *at least* the
 	provided frequency. This function is useful while searching for a
@@ -173,17 +159,15 @@ dev_pm_opp_find_freq_ceil - Search for an available OPP which is *at least* the
 	frequency.
 	Example 1: To find the lowest opp for a device:
 	 freq = 0;
-	 rcu_read_lock();
-	 dev_pm_opp_find_freq_ceil(dev, &freq);
-	 rcu_read_unlock();
+	 opp = dev_pm_opp_find_freq_ceil(dev, &freq);
+	 dev_pm_opp_put(opp);
 	Example 2: A simplified implementation of a SoC cpufreq_driver->target:
 	 soc_cpufreq_target(..)
 	 {
 		/* Do stuff like policy checks etc. */
 		/* Find the best frequency match for the req */
-		rcu_read_lock();
 		opp = dev_pm_opp_find_freq_ceil(dev, &freq);
-		rcu_read_unlock();
+		dev_pm_opp_put(opp);
 		if (!IS_ERR(opp))
 			soc_switch_to_freq_voltage(freq);
 		else
@@ -208,9 +192,8 @@ dev_pm_opp_enable - Make a OPP available for operation.
 	implementation might choose to do something as follows:
 	 if (cur_temp < temp_low_thresh) {
 		/* Enable 1GHz if it was disabled */
-		rcu_read_lock();
 		opp = dev_pm_opp_find_freq_exact(dev, 1000000000, false);
-		rcu_read_unlock();
+		dev_pm_opp_put(opp);
 		/* just error check */
 		if (!IS_ERR(opp))
 			ret = dev_pm_opp_enable(dev, 1000000000);
@@ -224,9 +207,8 @@ dev_pm_opp_disable - Make an OPP to be not available for operation
 	choose to do something as follows:
 	 if (cur_temp > temp_high_thresh) {
 		/* Disable 1GHz if it was enabled */
-		rcu_read_lock();
 		opp = dev_pm_opp_find_freq_exact(dev, 1000000000, true);
-		rcu_read_unlock();
+		dev_pm_opp_put(opp);
 		/* just error check */
 		if (!IS_ERR(opp))
 			ret = dev_pm_opp_disable(dev, 1000000000);
@@ -249,10 +231,9 @@ dev_pm_opp_get_voltage - Retrieve the voltage represented by the opp pointer.
 	 soc_switch_to_freq_voltage(freq)
 	 {
 		/* do things */
-		rcu_read_lock();
 		opp = dev_pm_opp_find_freq_ceil(dev, &freq);
 		v = dev_pm_opp_get_voltage(opp);
-		rcu_read_unlock();
+		dev_pm_opp_put(opp);
 		if (v)
 			regulator_set_voltage(.., v);
 		/* do other things */
@@ -266,12 +247,12 @@ dev_pm_opp_get_freq - Retrieve the freq represented by the opp pointer.
 	 {
 		/* do things.. */
 		 max_freq = ULONG_MAX;
-		 rcu_read_lock();
 		 max_opp = dev_pm_opp_find_freq_floor(dev,&max_freq);
 		 requested_opp = dev_pm_opp_find_freq_ceil(dev,&freq);
 		 if (!IS_ERR(max_opp) && !IS_ERR(requested_opp))
 			r = soc_test_validity(max_opp, requested_opp);
-		 rcu_read_unlock();
+		 dev_pm_opp_put(max_opp);
+		 dev_pm_opp_put(requested_opp);
 		/* do other things */
 	 }
 	 soc_test_validity(..)
@@ -289,7 +270,6 @@ dev_pm_opp_get_opp_count - Retrieve the number of available opps for a device
 	 soc_notify_coproc_available_frequencies()
 	 {
 		/* Do things */
-		rcu_read_lock();
 		num_available = dev_pm_opp_get_opp_count(dev);
 		speeds = kzalloc(sizeof(u32) * num_available, GFP_KERNEL);
 		/* populate the table in increasing order */
@@ -298,8 +278,8 @@ dev_pm_opp_get_opp_count - Retrieve the number of available opps for a device
 			speeds[i] = freq;
 			freq++;
 			i++;
+			dev_pm_opp_put(opp);
 		}
-		rcu_read_unlock();
 
 		soc_notify_coproc(AVAILABLE_FREQs, speeds, num_available);
 		/* Do other things */
diff --git a/Documentation/power/states.txt b/Documentation/power/states.txt
index 008ecb588317..bc4548245a24 100644
--- a/Documentation/power/states.txt
+++ b/Documentation/power/states.txt
@@ -25,7 +25,7 @@ to be used subsequently to change to the one represented by that string.
 Consequently, there are two ways to cause the system to go into the
 Suspend-To-Idle sleep state.  The first one is to write "freeze" directly to
 /sys/power/state.  The second one is to write "s2idle" to /sys/power/mem_sleep
-and then to wrtie "mem" to /sys/power/state.  Similarly, there are two ways
+and then to write "mem" to /sys/power/state.  Similarly, there are two ways
 to cause the system to go into the Power-On Suspend sleep state (the strings to
 write to the control files in that case are "standby" or "shallow" and "mem",
 respectively) if that state is supported by the platform.  In turn, there is