Merge remote-tracking branch 'asoc/topic/msm8916' into asoc-next

3 files changed, 66 insertions, 1 deletions

diff --git a/Documentation/devicetree/bindings/sound/dmic.txt b/Documentation/devicetree/bindings/sound/dmic.txt
new file mode 100644
index 000000000000..54c8ef6498a8
--- /dev/null
+++ b/Documentation/devicetree/bindings/sound/dmic.txt
@@ -0,0 +1,16 @@
+Device-Tree bindings for Digital microphone (DMIC) codec
+
+This device support generic PDM digital microphone.
+
+Required properties:
+	- compatible: should be "dmic-codec".
+
+Optional properties:
+	- dmicen-gpios: GPIO specifier for dmic to control start and stop
+
+Example node:
+
+	dmic_codec: dmic@0 {
+		compatible = "dmic-codec";
+		dmicen-gpios = <&gpio4 3 GPIO_ACTIVE_HIGH>;
+	};
diff --git a/Documentation/devicetree/bindings/sound/qcom,msm8916-wcd-analog.txt b/Documentation/devicetree/bindings/sound/qcom,msm8916-wcd-analog.txt
index ccb401cfef9d..551ecab67efe 100644
--- a/Documentation/devicetree/bindings/sound/qcom,msm8916-wcd-analog.txt
+++ b/Documentation/devicetree/bindings/sound/qcom,msm8916-wcd-analog.txt
@@ -31,8 +31,22 @@ Required properties
  - vdd-cdc-io-supply: phandle to VDD_CDC_IO regulator DT node.
  - vdd-cdc-tx-rx-cx-supply: phandle to VDD_CDC_TX/RX/CX regulator DT node.
  - vdd-micbias-supply: phandle of VDD_MICBIAS supply's regulator DT node.
-
 Optional Properties:
+ - qcom,mbhc-vthreshold-low: Array of 5 threshold voltages in mV for 5 buttons
+			     detection on headset when the mbhc is powered up
+			     by internal current source, this is a low power.
+ - qcom,mbhc-vthreshold-high: Array of 5 thresold voltages in mV for 5 buttons
+			      detection on headset when mbhc is powered up
+			       from micbias.
+- qcom,micbias-lvl:  Voltage (mV) for Mic Bias
+- qcom,hphl-jack-type-normally-open: boolean, present if hphl pin on jack is a
+				     NO (Normally Open). If not specified, then
+				     its assumed that hphl pin on jack is NC
+				     (Normally Closed).
+- qcom,gnd-jack-type-normally-open: boolean, present if gnd pin on jack is
+				    NO (Normally Open). If not specified, then
+				    its assumed that gnd pin on jack is NC
+				    (Normally Closed).
 - qcom,micbias1-ext-cap: boolean, present if micbias1 has external capacitor
 			 connected.
 - qcom,micbias2-ext-cap: boolean, present if micbias2 has external capacitor
@@ -48,6 +62,8 @@ spmi_bus {
 		reg-names = "pmic-codec-core";
 		clocks = <&gcc GCC_CODEC_DIGCODEC_CLK>;
 		clock-names = "mclk";
+		qcom,mbhc-vthreshold-low = <75 150 237 450 500>;
+		qcom,mbhc-vthreshold-high = <75 150 237 450 500>;
 		interrupt-parent = <&spmi_bus>;
 		interrupts = <0x1 0xf0 0x0 IRQ_TYPE_NONE>,
 			     <0x1 0xf0 0x1 IRQ_TYPE_NONE>,
diff --git a/Documentation/devicetree/bindings/sound/rt274.txt b/Documentation/devicetree/bindings/sound/rt274.txt
new file mode 100644
index 000000000000..e9a6178c78cf
--- /dev/null
+++ b/Documentation/devicetree/bindings/sound/rt274.txt
@@ -0,0 +1,33 @@
+RT274 audio CODEC
+
+This device supports I2C only.
+
+Required properties:
+
+- compatible : "realtek,rt274".
+
+- reg : The I2C address of the device.
+
+Optional properties:
+
+- interrupts : The CODEC's interrupt output.
+
+
+Pins on the device (for linking into audio routes) for RT274:
+
+  * DMIC1 Pin
+  * DMIC2 Pin
+  * MIC
+  * LINE1
+  * LINE2
+  * HPO Pin
+  * SPDIF
+  * LINE3
+
+Example:
+
+codec: rt274@1c {
+	compatible = "realtek,rt274";
+	reg = <0x1c>;
+	interrupts = <7 IRQ_TYPE_EDGE_FALLING>;
+};