Merge tag 'omap-for-v3.16/pm-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/soc

Merge "ARM: omap pm changes for v3.16 merge window, resend" from Tony Lindgren:

PM related fixes for omap3 that were discovered during omap3
conversion to device tree. This series sets up the PMIC signaling
in a way where we can test for PM regressions easily by
looking at state of the the sys_clkreq and sys_off_mode pins.

Note that this series alone does not make omap3 PM to cut
off core voltage during off-idle, changes to twl4030-power.c
configurations are still needed. Those will be posted
separately.

* tag 'omap-for-v3.16/pm-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
  ARM: OMAP2+: Enable CPUidle in omap2plus_defconfig
  ARM: dts: Enable N900 keyboard sleep leds by default
  ARM: OMAP2+: Fix voltage scaling init for device tree
  ARM: dts: Configure omap3 twl4030 I2C4 pins by default
  ARM: OMAP3: Fix voltage control for deeper idle states
  ARM: OMAP3: Disable broken omap3_set_off_timings function
  ARM: OMAP3: Fix idle mode signaling for sys_clkreq and sys_off_mode
  ARM: dts: Fix omap serial wake-up when booted with device tree
  mfd: twl-core: Fix idle mode signaling for omaps when booted with device tree

Signed-off-by: Olof Johansson <olof@lixom.net>

6 files changed, 184 insertions, 154 deletions

diff --git a/arch/arm/mach-omap2/omap_twl.c b/arch/arm/mach-omap2/omap_twl.c
index 615e5b1fb025..6bf626700557 100644
--- a/arch/arm/mach-omap2/omap_twl.c
+++ b/arch/arm/mach-omap2/omap_twl.c
@@ -46,15 +46,8 @@
 
 static bool is_offset_valid;
 static u8 smps_offset;
-/*
- * Flag to ensure Smartreflex bit in TWL
- * being cleared in board file is not overwritten.
- */
-static bool __initdata twl_sr_enable_autoinit;
 
-#define TWL4030_DCDC_GLOBAL_CFG        0x06
 #define REG_SMPS_OFFSET         0xE0
-#define SMARTREFLEX_ENABLE     BIT(3)
 
 static unsigned long twl4030_vsel_to_uv(const u8 vsel)
 {
@@ -251,18 +244,6 @@ int __init omap3_twl_init(void)
 	if (!cpu_is_omap34xx())
 		return -ENODEV;
 
-	/*
-	 * The smartreflex bit on twl4030 specifies if the setting of voltage
-	 * is done over the I2C_SR path. Since this setting is independent of
-	 * the actual usage of smartreflex AVS module, we enable TWL SR bit
-	 * by default irrespective of whether smartreflex AVS module is enabled
-	 * on the OMAP side or not. This is because without this bit enabled,
-	 * the voltage scaling through vp forceupdate/bypass mechanism of
-	 * voltage scaling will not function on TWL over I2C_SR.
-	 */
-	if (!twl_sr_enable_autoinit)
-		omap3_twl_set_sr_bit(true);
-
 	voltdm = voltdm_lookup("mpu_iva");
 	omap_voltage_register_pmic(voltdm, &omap3_mpu_pmic);
 
@@ -271,44 +252,3 @@ int __init omap3_twl_init(void)
 
 	return 0;
 }
-
-/**
- * omap3_twl_set_sr_bit() - Set/Clear SR bit on TWL
- * @enable: enable SR mode in twl or not
- *
- * If 'enable' is true, enables Smartreflex bit on TWL 4030 to make sure
- * voltage scaling through OMAP SR works. Else, the smartreflex bit
- * on twl4030 is cleared as there are platforms which use OMAP3 and T2 but
- * use Synchronized Scaling Hardware Strategy (ENABLE_VMODE=1) and Direct
- * Strategy Software Scaling Mode (ENABLE_VMODE=0), for setting the voltages,
- * in those scenarios this bit is to be cleared (enable = false).
- *
- * Returns 0 on success, error is returned if I2C read/write fails.
- */
-int __init omap3_twl_set_sr_bit(bool enable)
-{
-	u8 temp;
-	int ret;
-	if (twl_sr_enable_autoinit)
-		pr_warning("%s: unexpected multiple calls\n", __func__);
-
-	ret = twl_i2c_read_u8(TWL_MODULE_PM_RECEIVER, &temp,
-			      TWL4030_DCDC_GLOBAL_CFG);
-	if (ret)
-		goto err;
-
-	if (enable)
-		temp |= SMARTREFLEX_ENABLE;
-	else
-		temp &= ~SMARTREFLEX_ENABLE;
-
-	ret = twl_i2c_write_u8(TWL_MODULE_PM_RECEIVER, temp,
-			       TWL4030_DCDC_GLOBAL_CFG);
-	if (!ret) {
-		twl_sr_enable_autoinit = true;
-		return 0;
-	}
-err:
-	pr_err("%s: Error access to TWL4030 (%d)\n", __func__, ret);
-	return ret;
-}
diff --git a/arch/arm/mach-omap2/pm.c b/arch/arm/mach-omap2/pm.c
index dd31212d5e20..828aee9ea6a8 100644
--- a/arch/arm/mach-omap2/pm.c
+++ b/arch/arm/mach-omap2/pm.c
@@ -298,25 +298,21 @@ omap_postcore_initcall(omap2_common_pm_init);
 
 int __init omap2_common_pm_late_init(void)
 {
-	/*
-	 * In the case of DT, the PMIC and SR initialization will be done using
-	 * a completely different mechanism.
-	 * Disable this part if a DT blob is available.
-	 */
-	if (!of_have_populated_dt()) {
-
-		/* Init the voltage layer */
-		omap_pmic_late_init();
-		omap_voltage_late_init();
+	if (of_have_populated_dt()) {
+		omap3_twl_init();
+		omap4_twl_init();
+	}
 
-		/* Initialize the voltages */
-		omap3_init_voltages();
-		omap4_init_voltages();
+	/* Init the voltage layer */
+	omap_pmic_late_init();
+	omap_voltage_late_init();
 
-		/* Smartreflex device init */
-		omap_devinit_smartreflex();
+	/* Initialize the voltages */
+	omap3_init_voltages();
+	omap4_init_voltages();
 
-	}
+	/* Smartreflex device init */
+	omap_devinit_smartreflex();
 
 	/* cpufreq dummy device instantiation */
 	omap_init_cpufreq();
diff --git a/arch/arm/mach-omap2/pm34xx.c b/arch/arm/mach-omap2/pm34xx.c
index 90ea2d3ab405..507d8eeaab95 100644
--- a/arch/arm/mach-omap2/pm34xx.c
+++ b/arch/arm/mach-omap2/pm34xx.c
@@ -50,6 +50,7 @@
 #include "sdrc.h"
 #include "sram.h"
 #include "control.h"
+#include "vc.h"
 
 /* pm34xx errata defined in pm.h */
 u16 pm34xx_errata;
@@ -288,6 +289,9 @@ void omap_sram_idle(void)
 		}
 	}
 
+	/* Configure PMIC signaling for I2C4 or sys_off_mode */
+	omap3_vc_set_pmic_signaling(core_next_state);
+
 	omap3_intc_prepare_idle();
 
 	/*
diff --git a/arch/arm/mach-omap2/prm-regbits-34xx.h b/arch/arm/mach-omap2/prm-regbits-34xx.h
index cebad565ed37..106132db532b 100644
--- a/arch/arm/mach-omap2/prm-regbits-34xx.h
+++ b/arch/arm/mach-omap2/prm-regbits-34xx.h
@@ -123,8 +123,15 @@
 #define OMAP3430_GLOBAL_SW_RST_SHIFT			1
 #define OMAP3430_GLOBAL_COLD_RST_SHIFT			0
 #define OMAP3430_GLOBAL_COLD_RST_MASK			(1 << 0)
-#define OMAP3430_SEL_OFF_MASK				(1 << 3)
-#define OMAP3430_AUTO_OFF_MASK				(1 << 2)
+#define OMAP3430_PRM_VOLTCTRL_SEL_VMODE			(1 << 4)
+#define OMAP3430_PRM_VOLTCTRL_SEL_OFF			(1 << 3)
+#define OMAP3430_PRM_VOLTCTRL_AUTO_OFF			(1 << 2)
+#define OMAP3430_PRM_VOLTCTRL_AUTO_RET			(1 << 1)
+#define OMAP3430_PRM_VOLTCTRL_AUTO_SLEEP		(1 << 0)
 #define OMAP3430_SETUP_TIME2_MASK			(0xffff << 16)
 #define OMAP3430_SETUP_TIME1_MASK			(0xffff << 0)
+#define OMAP3430_PRM_POLCTRL_OFFMODE_POL		(1 << 3)
+#define OMAP3430_PRM_POLCTRL_CLKOUT_POL			(1 << 2)
+#define OMAP3430_PRM_POLCTRL_CLKREQ_POL			(1 << 1)
+#define OMAP3430_PRM_POLCTRL_EXTVOL_POL			(1 << 0)
 #endif
diff --git a/arch/arm/mach-omap2/vc.c b/arch/arm/mach-omap2/vc.c
index 49ac7977e03e..0d1629c5f84e 100644
--- a/arch/arm/mach-omap2/vc.c
+++ b/arch/arm/mach-omap2/vc.c
@@ -220,10 +220,126 @@ static inline u32 omap_usec_to_32k(u32 usec)
 	return DIV_ROUND_UP_ULL(32768ULL * (u64)usec, 1000000ULL);
 }
 
-/* Set oscillator setup time for omap3 */
-static void omap3_set_clksetup(u32 usec, struct voltagedomain *voltdm)
+struct omap3_vc_timings {
+	u32 voltsetup1;
+	u32 voltsetup2;
+};
+
+struct omap3_vc {
+	struct voltagedomain *vd;
+	u32 voltctrl;
+	u32 voltsetup1;
+	u32 voltsetup2;
+	struct omap3_vc_timings timings[2];
+};
+static struct omap3_vc vc;
+
+void omap3_vc_set_pmic_signaling(int core_next_state)
+{
+	struct voltagedomain *vd = vc.vd;
+	struct omap3_vc_timings *c = vc.timings;
+	u32 voltctrl, voltsetup1, voltsetup2;
+
+	voltctrl = vc.voltctrl;
+	voltsetup1 = vc.voltsetup1;
+	voltsetup2 = vc.voltsetup2;
+
+	switch (core_next_state) {
+	case PWRDM_POWER_OFF:
+		voltctrl &= ~(OMAP3430_PRM_VOLTCTRL_AUTO_RET |
+			      OMAP3430_PRM_VOLTCTRL_AUTO_SLEEP);
+		voltctrl |= OMAP3430_PRM_VOLTCTRL_AUTO_OFF;
+		if (voltctrl & OMAP3430_PRM_VOLTCTRL_SEL_OFF)
+			voltsetup2 = c->voltsetup2;
+		else
+			voltsetup1 = c->voltsetup1;
+		break;
+	case PWRDM_POWER_RET:
+	default:
+		c++;
+		voltctrl &= ~(OMAP3430_PRM_VOLTCTRL_AUTO_OFF |
+			      OMAP3430_PRM_VOLTCTRL_AUTO_SLEEP);
+		voltctrl |= OMAP3430_PRM_VOLTCTRL_AUTO_RET;
+		voltsetup1 = c->voltsetup1;
+		break;
+	}
+
+	if (voltctrl != vc.voltctrl) {
+		vd->write(voltctrl, OMAP3_PRM_VOLTCTRL_OFFSET);
+		vc.voltctrl = voltctrl;
+	}
+	if (voltsetup1 != vc.voltsetup1) {
+		vd->write(c->voltsetup1,
+			  OMAP3_PRM_VOLTSETUP1_OFFSET);
+		vc.voltsetup1 = voltsetup1;
+	}
+	if (voltsetup2 != vc.voltsetup2) {
+		vd->write(c->voltsetup2,
+			  OMAP3_PRM_VOLTSETUP2_OFFSET);
+		vc.voltsetup2 = voltsetup2;
+	}
+}
+
+#define PRM_POLCTRL_TWL_MASK	(OMAP3430_PRM_POLCTRL_CLKREQ_POL | \
+					OMAP3430_PRM_POLCTRL_CLKREQ_POL)
+#define PRM_POLCTRL_TWL_VAL	OMAP3430_PRM_POLCTRL_CLKREQ_POL
+
+/*
+ * Configure signal polarity for sys_clkreq and sys_off_mode pins
+ * as the default values are wrong and can cause the system to hang
+ * if any twl4030 scripts are loaded.
+ */
+static void __init omap3_vc_init_pmic_signaling(struct voltagedomain *voltdm)
+{
+	u32 val;
+
+	if (vc.vd)
+		return;
+
+	vc.vd = voltdm;
+
+	val = voltdm->read(OMAP3_PRM_POLCTRL_OFFSET);
+	if (!(val & OMAP3430_PRM_POLCTRL_CLKREQ_POL) ||
+	    (val & OMAP3430_PRM_POLCTRL_CLKREQ_POL)) {
+		val |= OMAP3430_PRM_POLCTRL_CLKREQ_POL;
+		val &= ~OMAP3430_PRM_POLCTRL_OFFMODE_POL;
+		pr_debug("PM: fixing sys_clkreq and sys_off_mode polarity to 0x%x\n",
+			 val);
+		voltdm->write(val, OMAP3_PRM_POLCTRL_OFFSET);
+	}
+
+	/*
+	 * By default let's use I2C4 signaling for retention idle
+	 * and sys_off_mode pin signaling for off idle. This way we
+	 * have sys_clk_req pin go down for retention and both
+	 * sys_clk_req and sys_off_mode pins will go down for off
+	 * idle. And we can also scale voltages to zero for off-idle.
+	 * Note that no actual voltage scaling during off-idle will
+	 * happen unless the board specific twl4030 PMIC scripts are
+	 * loaded.
+	 */
+	val = voltdm->read(OMAP3_PRM_VOLTCTRL_OFFSET);
+	if (!(val & OMAP3430_PRM_VOLTCTRL_SEL_OFF)) {
+		val |= OMAP3430_PRM_VOLTCTRL_SEL_OFF;
+		pr_debug("PM: setting voltctrl sys_off_mode signaling to 0x%x\n",
+			 val);
+		voltdm->write(val, OMAP3_PRM_VOLTCTRL_OFFSET);
+	}
+	vc.voltctrl = val;
+
+	omap3_vc_set_pmic_signaling(PWRDM_POWER_ON);
+}
+
+static void omap3_init_voltsetup1(struct voltagedomain *voltdm,
+				  struct omap3_vc_timings *c, u32 idle)
 {
-	voltdm->write(omap_usec_to_32k(usec), OMAP3_PRM_CLKSETUP_OFFSET);
+	unsigned long val;
+
+	val = (voltdm->vc_param->on - idle) / voltdm->pmic->slew_rate;
+	val *= voltdm->sys_clk.rate / 8 / 1000000 + 1;
+	val <<= __ffs(voltdm->vfsm->voltsetup_mask);
+	c->voltsetup1 &= ~voltdm->vfsm->voltsetup_mask;
+	c->voltsetup1 |= val;
 }
 
 /**
@@ -236,37 +352,21 @@ static void omap3_set_clksetup(u32 usec, struct voltagedomain *voltdm)
  * or retention. Off mode has additionally an option to use sys_off_mode
  * pad, which uses a global signal to program the whole power IC to
  * off-mode.
+ *
+ * Note that pmic is not controlling the voltage scaling during
+ * retention signaled over I2C4, so we can keep voltsetup2 as 0.
+ * And the oscillator is not shut off over I2C4, so no need to
+ * set clksetup.
  */
-static void omap3_set_i2c_timings(struct voltagedomain *voltdm, bool off_mode)
+static void omap3_set_i2c_timings(struct voltagedomain *voltdm)
 {
-	unsigned long voltsetup1;
-	u32 tgt_volt;
-
-	/*
-	 * Oscillator is shut down only if we are using sys_off_mode pad,
-	 * thus we set a minimal setup time here
-	 */
-	omap3_set_clksetup(1, voltdm);
+	struct omap3_vc_timings *c = vc.timings;
 
-	if (off_mode)
-		tgt_volt = voltdm->vc_param->off;
-	else
-		tgt_volt = voltdm->vc_param->ret;
-
-	voltsetup1 = (voltdm->vc_param->on - tgt_volt) /
-			voltdm->pmic->slew_rate;
-
-	voltsetup1 = voltsetup1 * voltdm->sys_clk.rate / 8 / 1000000 + 1;
-
-	voltdm->rmw(voltdm->vfsm->voltsetup_mask,
-		voltsetup1 << __ffs(voltdm->vfsm->voltsetup_mask),
-		voltdm->vfsm->voltsetup_reg);
-
-	/*
-	 * pmic is not controlling the voltage scaling during retention,
-	 * thus set voltsetup2 to 0
-	 */
-	voltdm->write(0, OMAP3_PRM_VOLTSETUP2_OFFSET);
+	/* Configure PRWDM_POWER_OFF over I2C4 */
+	omap3_init_voltsetup1(voltdm, c, voltdm->vc_param->off);
+	c++;
+	/* Configure PRWDM_POWER_RET over I2C4 */
+	omap3_init_voltsetup1(voltdm, c, voltdm->vc_param->ret);
 }
 
 /**
@@ -275,69 +375,49 @@ static void omap3_set_i2c_timings(struct voltagedomain *voltdm, bool off_mode)
  *
  * Calculates and sets up off-mode timings for a channel. Off-mode
  * can use either I2C based voltage scaling, or alternatively
- * sys_off_mode pad can be used to send a global command to power IC.
- * This function first checks which mode is being used, and calls
- * omap3_set_i2c_timings() if the system is using I2C control mode.
+ * sys_off_mode pad can be used to send a global command to power IC.n,
  * sys_off_mode has the additional benefit that voltages can be
  * scaled to zero volt level with TWL4030 / TWL5030, I2C can only
  * scale to 600mV.
+ *
+ * Note that omap is not controlling the voltage scaling during
+ * off idle signaled by sys_off_mode, so we can keep voltsetup1
+ * as 0.
  */
 static void omap3_set_off_timings(struct voltagedomain *voltdm)
 {
-	unsigned long clksetup;
-	unsigned long voltsetup2;
-	unsigned long voltsetup2_old;
-	u32 val;
-	u32 tstart, tshut;
+	struct omap3_vc_timings *c = vc.timings;
+	u32 tstart, tshut, clksetup, voltoffset;
 
-	/* check if sys_off_mode is used to control off-mode voltages */
-	val = voltdm->read(OMAP3_PRM_VOLTCTRL_OFFSET);
-	if (!(val & OMAP3430_SEL_OFF_MASK)) {
-		/* No, omap is controlling them over I2C */
-		omap3_set_i2c_timings(voltdm, true);
+	if (c->voltsetup2)
 		return;
-	}
 
 	omap_pm_get_oscillator(&tstart, &tshut);
-	omap3_set_clksetup(tstart, voltdm);
-
-	clksetup = voltdm->read(OMAP3_PRM_CLKSETUP_OFFSET);
-
-	/* voltsetup 2 in us */
-	voltsetup2 = voltdm->vc_param->on / voltdm->pmic->slew_rate;
-
-	/* convert to 32k clk cycles */
-	voltsetup2 = DIV_ROUND_UP(voltsetup2 * 32768, 1000000);
-
-	voltsetup2_old = voltdm->read(OMAP3_PRM_VOLTSETUP2_OFFSET);
-
-	/*
-	 * Update voltsetup2 if higher than current value (needed because
-	 * we have multiple channels with different ramp times), also
-	 * update voltoffset always to value recommended by TRM
-	 */
-	if (voltsetup2 > voltsetup2_old) {
-		voltdm->write(voltsetup2, OMAP3_PRM_VOLTSETUP2_OFFSET);
-		voltdm->write(clksetup - voltsetup2,
-			OMAP3_PRM_VOLTOFFSET_OFFSET);
-	} else
-		voltdm->write(clksetup - voltsetup2_old,
-			OMAP3_PRM_VOLTOFFSET_OFFSET);
+	if (tstart == ULONG_MAX) {
+		pr_debug("PM: oscillator start-up time not initialized, using 10ms\n");
+		clksetup = omap_usec_to_32k(10000);
+	} else {
+		clksetup = omap_usec_to_32k(tstart);
+	}
 
 	/*
-	 * omap is not controlling voltage scaling during off-mode,
-	 * thus set voltsetup1 to 0
+	 * For twl4030 errata 27, we need to allow minimum ~488.32 us wait to
+	 * switch from HFCLKIN to internal oscillator. That means timings
+	 * have voltoffset fixed to 0xa in rounded up 32 KiHz cycles. And
+	 * that means we can calculate the value based on the oscillator
+	 * start-up time since voltoffset2 = clksetup - voltoffset.
 	 */
-	voltdm->rmw(voltdm->vfsm->voltsetup_mask, 0,
-		voltdm->vfsm->voltsetup_reg);
-
-	/* voltoffset must be clksetup minus voltsetup2 according to TRM */
-	voltdm->write(clksetup - voltsetup2, OMAP3_PRM_VOLTOFFSET_OFFSET);
+	voltoffset = omap_usec_to_32k(488);
+	c->voltsetup2 = clksetup - voltoffset;
+	voltdm->write(clksetup, OMAP3_PRM_CLKSETUP_OFFSET);
+	voltdm->write(voltoffset, OMAP3_PRM_VOLTOFFSET_OFFSET);
 }
 
 static void __init omap3_vc_init_channel(struct voltagedomain *voltdm)
 {
+	omap3_vc_init_pmic_signaling(voltdm);
 	omap3_set_off_timings(voltdm);
+	omap3_set_i2c_timings(voltdm);
 }
 
 /**
diff --git a/arch/arm/mach-omap2/vc.h b/arch/arm/mach-omap2/vc.h
index 91c8d75bf2ea..cdbdd78e755e 100644
--- a/arch/arm/mach-omap2/vc.h
+++ b/arch/arm/mach-omap2/vc.h
@@ -117,6 +117,9 @@ extern struct omap_vc_param omap4_mpu_vc_data;
 extern struct omap_vc_param omap4_iva_vc_data;
 extern struct omap_vc_param omap4_core_vc_data;
 
+void omap3_vc_set_pmic_signaling(int core_next_state);
+
+
 void omap_vc_init_channel(struct voltagedomain *voltdm);
 int omap_vc_pre_scale(struct voltagedomain *voltdm,
 		      unsigned long target_volt,