diff options
| author | Linus Torvalds <torvalds@linux-foundation.org> | 2023-02-20 15:49:56 -0800 |
|---|---|---|
| committer | Linus Torvalds <torvalds@linux-foundation.org> | 2023-02-20 15:49:56 -0800 |
| commit | 950b6662e26e381cf8834b9b78b08261890ee697 (patch) | |
| tree | f6055bfca2a0c9e02724921e64cbde72905118e7 /arch/arm64/boot/dts/freescale | |
| parent | c72e04c26faefc6650709066a8f019a7fb4cbb84 (diff) | |
| parent | e43efb6d713bca3855909a2f9caec280a2b0a503 (diff) | |
Merge tag 'soc-dt-6.3' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull SoC DT updates from Arnd Bergmann:
"About a quarter of the changes are for 32-bit arm, mostly filling in
device support for existing machines and adding minor cleanups, mostly
for Qualcomm and Samsung based machines.
Two new 32-bit SoCs are added, both are quad-core Cortex-A7 chips from
Rockchips that have been around for a while but were lacking kernel
support so far: RV1126 is a Vision SoC with an NPU and is used in the
Edgeble Neural Compute Module 2(Neu2) board, while RK3128 is design
for TV boxes and so far only comes with a dts for its refernece
design.
The other 32-bit boards that were added are two ASpeed AST2600 based
BMC boards, the Microchip sam9x60_curiosity development board (Armv5
based!), the Enclustra PE1 FPGA-SoM baseboard, and a few more boards
for i.MX53 and i.MX6ULL.
On the RISC-V side, there are fewer patches, but a total of ten new
single-board computers based on variations of the Allwinner D1/T113
chip, plus one more board based on Microchip Polarfire.
As usual, arm64 has by far the most changes here, with over 700
non-merge changesets, among them over 400 alone for Qualcomm. The
newly added SoCs this time are all recent high-end embedded SoCs for
various markets, each on comes with support for its reference board:
- Qualcomm SM8550 (Snapdragon 8 Gen 2) for mobile phones
- Qualcomm QDU1000/QRU1000 5G RAN platform
- Rockchips RK3588/RK3588s for tablets, chromebooks and SBCs
- TI J784S4 for industrial and automotive applications
In total, there are 46 new arm64 machines:
- Reference platforms for each of the five new SoCs
- Three Amlogic based development boards
- Six embedded machines based on NXP i.MX8MM and i.MX8MP
- The Mediatek mt7986a based Banana Pi R3 router
- Six tablets based on Qualcomm MSM8916 (Snapdragon 410), SM6115
(Snapdragon 662) and SM8250 (Snapdragon 865)
- Two LTE dongles, also based on MSM8916
- Seven mobile phones, based on Qualcomm MSM8953 (Snapdragon 610),
SDM450 and SDM632
- Three chromebooks based on Qualcomm SC7280 (Snapdragon 7c)
- Nine development boards based on Rockchips RK3588, RK3568, RK3566
and RK3328.
- Five development machines based on TI K3 (AM642/AM654/AM68/AM69)
The cleanup of dtc warnings continues across all platforms, adding to
the total number of changes"
* tag 'soc-dt-6.3' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (1035 commits)
dt-bindings: riscv: correct starfive visionfive 2 compatibles
ARM: dts: socfpga: Add enclustra PE1 devicetree
dt-bindings: altera: Add enclustra mercury PE1
arm64: dts: qcom: msm8996: align RPM G-Link clock-controller node with bindings
arm64: dts: qcom: qcs404: align RPM G-Link node with bindings
arm64: dts: qcom: ipq6018: align RPM G-Link node with bindings
arm64: dts: qcom: sm8550: remove invalid interconnect property from cryptobam
arm64: dts: qcom: sc7280: Adjust zombie PWM frequency
arm64: dts: qcom: sc8280xp-pmics: Specify interrupt parent explicitly
arm64: dts: qcom: sm7225-fairphone-fp4: enable remaining i2c busses
arm64: dts: qcom: sm7225-fairphone-fp4: move status property down
arm64: dts: qcom: pmk8350: Use the correct PON compatible
arm64: dts: qcom: sc8280xp-x13s: Enable external display
arm64: dts: qcom: sc8280xp-crd: Introduce pmic_glink
arm64: dts: qcom: sc8280xp: Add USB-C-related DP blocks
arm64: dts: qcom: sm8350-hdk: enable GPU
arm64: dts: qcom: sm8350: add GPU, GMU, GPU CC and SMMU nodes
arm64: dts: qcom: sm8350: finish reordering nodes
arm64: dts: qcom: sm8350: move more nodes to correct place
arm64: dts: qcom: sm8350: reorder device nodes
...
Diffstat (limited to 'arch/arm64/boot/dts/freescale')
67 files changed, 2717 insertions, 280 deletions
diff --git a/arch/arm64/boot/dts/freescale/Makefile b/arch/arm64/boot/dts/freescale/Makefile index ef6f364eaa18..198fff3731ae 100644 --- a/arch/arm64/boot/dts/freescale/Makefile +++ b/arch/arm64/boot/dts/freescale/Makefile @@ -75,8 +75,10 @@ dtb-$(CONFIG_ARCH_MXC) += imx8mm-venice-gw7903.dtb dtb-$(CONFIG_ARCH_MXC) += imx8mm-venice-gw7904.dtb dtb-$(CONFIG_ARCH_MXC) += imx8mm-verdin-nonwifi-dahlia.dtb dtb-$(CONFIG_ARCH_MXC) += imx8mm-verdin-nonwifi-dev.dtb +dtb-$(CONFIG_ARCH_MXC) += imx8mm-verdin-nonwifi-yavia.dtb dtb-$(CONFIG_ARCH_MXC) += imx8mm-verdin-wifi-dahlia.dtb dtb-$(CONFIG_ARCH_MXC) += imx8mm-verdin-wifi-dev.dtb +dtb-$(CONFIG_ARCH_MXC) += imx8mm-verdin-wifi-yavia.dtb dtb-$(CONFIG_ARCH_MXC) += imx8mn-beacon-kit.dtb dtb-$(CONFIG_ARCH_MXC) += imx8mn-bsh-smm-s2.dtb dtb-$(CONFIG_ARCH_MXC) += imx8mn-bsh-smm-s2pro.dtb @@ -86,6 +88,8 @@ dtb-$(CONFIG_ARCH_MXC) += imx8mn-ddr4-evk.dtb dtb-$(CONFIG_ARCH_MXC) += imx8mn-tqma8mqnl-mba8mx.dtb dtb-$(CONFIG_ARCH_MXC) += imx8mn-var-som-symphony.dtb dtb-$(CONFIG_ARCH_MXC) += imx8mn-venice-gw7902.dtb +dtb-$(CONFIG_ARCH_MXC) += imx8mp-beacon-kit.dtb +dtb-$(CONFIG_ARCH_MXC) += imx8mp-debix-model-a.dtb dtb-$(CONFIG_ARCH_MXC) += imx8mp-dhcom-pdk2.dtb dtb-$(CONFIG_ARCH_MXC) += imx8mp-evk.dtb dtb-$(CONFIG_ARCH_MXC) += imx8mp-icore-mx8mp-edimm2.2.dtb @@ -95,8 +99,14 @@ dtb-$(CONFIG_ARCH_MXC) += imx8mp-tqma8mpql-mba8mpxl.dtb dtb-$(CONFIG_ARCH_MXC) += imx8mp-venice-gw74xx.dtb dtb-$(CONFIG_ARCH_MXC) += imx8mp-verdin-nonwifi-dahlia.dtb dtb-$(CONFIG_ARCH_MXC) += imx8mp-verdin-nonwifi-dev.dtb +dtb-$(CONFIG_ARCH_MXC) += imx8mp-verdin-nonwifi-yavia.dtb dtb-$(CONFIG_ARCH_MXC) += imx8mp-verdin-wifi-dahlia.dtb dtb-$(CONFIG_ARCH_MXC) += imx8mp-verdin-wifi-dev.dtb +dtb-$(CONFIG_ARCH_MXC) += imx8mp-verdin-wifi-yavia.dtb + +imx8mp-tqma8mpql-mba8mpxl-lvds-dtbs += imx8mp-tqma8mpql-mba8mpxl.dtb imx8mp-tqma8mpql-mba8mpxl-lvds.dtbo +dtb-$(CONFIG_ARCH_MXC) += imx8mp-tqma8mpql-mba8mpxl-lvds.dtb + dtb-$(CONFIG_ARCH_MXC) += imx8mq-evk.dtb dtb-$(CONFIG_ARCH_MXC) += imx8mq-hummingboard-pulse.dtb dtb-$(CONFIG_ARCH_MXC) += imx8mq-kontron-pitx-imx8m.dtb diff --git a/arch/arm64/boot/dts/freescale/fsl-ls1028a-kontron-kbox-a-230-ls.dts b/arch/arm64/boot/dts/freescale/fsl-ls1028a-kontron-kbox-a-230-ls.dts index 73eb6061c73e..af9194eca556 100644 --- a/arch/arm64/boot/dts/freescale/fsl-ls1028a-kontron-kbox-a-230-ls.dts +++ b/arch/arm64/boot/dts/freescale/fsl-ls1028a-kontron-kbox-a-230-ls.dts @@ -56,10 +56,14 @@ }; &enetc_port2 { + nvmem-cells = <&base_mac_address 2>; + nvmem-cell-names = "mac-address"; status = "okay"; }; &enetc_port3 { + nvmem-cells = <&base_mac_address 3>; + nvmem-cell-names = "mac-address"; status = "okay"; }; @@ -80,6 +84,8 @@ managed = "in-band-status"; phy-handle = <&qsgmii_phy0>; phy-mode = "qsgmii"; + nvmem-cells = <&base_mac_address 4>; + nvmem-cell-names = "mac-address"; status = "okay"; }; @@ -88,6 +94,8 @@ managed = "in-band-status"; phy-handle = <&qsgmii_phy1>; phy-mode = "qsgmii"; + nvmem-cells = <&base_mac_address 5>; + nvmem-cell-names = "mac-address"; status = "okay"; }; @@ -96,6 +104,8 @@ managed = "in-band-status"; phy-handle = <&qsgmii_phy2>; phy-mode = "qsgmii"; + nvmem-cells = <&base_mac_address 6>; + nvmem-cell-names = "mac-address"; status = "okay"; }; @@ -104,6 +114,8 @@ managed = "in-band-status"; phy-handle = <&qsgmii_phy3>; phy-mode = "qsgmii"; + nvmem-cells = <&base_mac_address 7>; + nvmem-cell-names = "mac-address"; status = "okay"; }; diff --git a/arch/arm64/boot/dts/freescale/fsl-ls1028a-kontron-sl28-var1.dts b/arch/arm64/boot/dts/freescale/fsl-ls1028a-kontron-sl28-var1.dts index 7cd29ab970d9..1f34c7553459 100644 --- a/arch/arm64/boot/dts/freescale/fsl-ls1028a-kontron-sl28-var1.dts +++ b/arch/arm64/boot/dts/freescale/fsl-ls1028a-kontron-sl28-var1.dts @@ -55,5 +55,7 @@ &enetc_port1 { phy-handle = <&phy0>; phy-mode = "rgmii-id"; + nvmem-cells = <&base_mac_address 0>; + nvmem-cell-names = "mac-address"; status = "okay"; }; diff --git a/arch/arm64/boot/dts/freescale/fsl-ls1028a-kontron-sl28-var2.dts b/arch/arm64/boot/dts/freescale/fsl-ls1028a-kontron-sl28-var2.dts index 113b1df74bf8..aac41192caa1 100644 --- a/arch/arm64/boot/dts/freescale/fsl-ls1028a-kontron-sl28-var2.dts +++ b/arch/arm64/boot/dts/freescale/fsl-ls1028a-kontron-sl28-var2.dts @@ -36,10 +36,14 @@ }; &enetc_port2 { + nvmem-cells = <&base_mac_address 2>; + nvmem-cell-names = "mac-address"; status = "okay"; }; &enetc_port3 { + nvmem-cells = <&base_mac_address 3>; + nvmem-cell-names = "mac-address"; status = "okay"; }; @@ -52,6 +56,8 @@ managed = "in-band-status"; phy-handle = <&phy0>; phy-mode = "sgmii"; + nvmem-cells = <&base_mac_address 0>; + nvmem-cell-names = "mac-address"; status = "okay"; }; @@ -60,6 +66,8 @@ managed = "in-band-status"; phy-handle = <&phy1>; phy-mode = "sgmii"; + nvmem-cells = <&base_mac_address 1>; + nvmem-cell-names = "mac-address"; status = "okay"; }; diff --git a/arch/arm64/boot/dts/freescale/fsl-ls1028a-kontron-sl28-var4.dts b/arch/arm64/boot/dts/freescale/fsl-ls1028a-kontron-sl28-var4.dts index 9b5e92fb753e..a4421db3784e 100644 --- a/arch/arm64/boot/dts/freescale/fsl-ls1028a-kontron-sl28-var4.dts +++ b/arch/arm64/boot/dts/freescale/fsl-ls1028a-kontron-sl28-var4.dts @@ -43,5 +43,7 @@ &enetc_port1 { phy-handle = <&phy1>; phy-mode = "rgmii-id"; + nvmem-cells = <&base_mac_address 1>; + nvmem-cell-names = "mac-address"; status = "okay"; }; diff --git a/arch/arm64/boot/dts/freescale/fsl-ls1028a-kontron-sl28.dts b/arch/arm64/boot/dts/freescale/fsl-ls1028a-kontron-sl28.dts index 4ab17b984b03..8b65af4a7147 100644 --- a/arch/arm64/boot/dts/freescale/fsl-ls1028a-kontron-sl28.dts +++ b/arch/arm64/boot/dts/freescale/fsl-ls1028a-kontron-sl28.dts @@ -92,6 +92,8 @@ phy-handle = <&phy0>; phy-mode = "sgmii"; managed = "in-band-status"; + nvmem-cells = <&base_mac_address 0>; + nvmem-cell-names = "mac-address"; status = "okay"; }; @@ -154,6 +156,21 @@ label = "bootloader environment"; }; }; + + otp-1 { + compatible = "user-otp"; + + nvmem-layout { + compatible = "kontron,sl28-vpd"; + + serial_number: serial-number { + }; + + base_mac_address: base-mac-address { + #nvmem-cell-cells = <1>; + }; + }; + }; }; }; diff --git a/arch/arm64/boot/dts/freescale/fsl-ls1028a.dtsi b/arch/arm64/boot/dts/freescale/fsl-ls1028a.dtsi index 1b33cabb4e14..9e50976bcb8e 100644 --- a/arch/arm64/boot/dts/freescale/fsl-ls1028a.dtsi +++ b/arch/arm64/boot/dts/freescale/fsl-ls1028a.dtsi @@ -713,6 +713,7 @@ reg = <0 0x5000000 0 0x800000>; #global-interrupts = <8>; #iommu-cells = <1>; + dma-coherent; stream-match-mask = <0x7c00>; /* global secure fault */ interrupts = <GIC_SPI 13 IRQ_TYPE_LEVEL_HIGH>, diff --git a/arch/arm64/boot/dts/freescale/fsl-ls1046a-rdb.dts b/arch/arm64/boot/dts/freescale/fsl-ls1046a-rdb.dts index 7025aad8ae89..07f6cc6e354a 100644 --- a/arch/arm64/boot/dts/freescale/fsl-ls1046a-rdb.dts +++ b/arch/arm64/boot/dts/freescale/fsl-ls1046a-rdb.dts @@ -153,8 +153,8 @@ }; ethernet@f2000 { /* 10GEC2 */ - fixed-link = <0 1 1000 0 0>; - phy-connection-type = "xgmii"; + phy-connection-type = "10gbase-r"; + managed = "in-band-status"; }; mdio@fc000 { diff --git a/arch/arm64/boot/dts/freescale/fsl-ls1088a.dtsi b/arch/arm64/boot/dts/freescale/fsl-ls1088a.dtsi index 260d045dbd9a..e5fb137ac02b 100644 --- a/arch/arm64/boot/dts/freescale/fsl-ls1088a.dtsi +++ b/arch/arm64/boot/dts/freescale/fsl-ls1088a.dtsi @@ -674,6 +674,7 @@ reg = <0 0x5000000 0 0x800000>; #iommu-cells = <1>; stream-match-mask = <0x7C00>; + dma-coherent; #global-interrupts = <12>; // global secure fault interrupts = <GIC_SPI 13 IRQ_TYPE_LEVEL_HIGH>, diff --git a/arch/arm64/boot/dts/freescale/imx8dxl-evk.dts b/arch/arm64/boot/dts/freescale/imx8dxl-evk.dts index 280a9c9d8bd9..1bcf228a22b8 100644 --- a/arch/arm64/boot/dts/freescale/imx8dxl-evk.dts +++ b/arch/arm64/boot/dts/freescale/imx8dxl-evk.dts @@ -135,6 +135,7 @@ reg = <0>; eee-broken-1000t; qca,disable-smarteee; + qca,disable-hibernation-mode; vddio-supply = <&vddio0>; vddio0: vddio-regulator { diff --git a/arch/arm64/boot/dts/freescale/imx8dxl-ss-conn.dtsi b/arch/arm64/boot/dts/freescale/imx8dxl-ss-conn.dtsi index 6b416fb760d5..ca195e6d8f37 100644 --- a/arch/arm64/boot/dts/freescale/imx8dxl-ss-conn.dtsi +++ b/arch/arm64/boot/dts/freescale/imx8dxl-ss-conn.dtsi @@ -67,7 +67,7 @@ reg = <0x5b0e0200 0x200>; }; - usbphy2: usbphy@0x5b110000 { + usbphy2: usbphy@5b110000 { compatible = "fsl,imx8dxl-usbphy", "fsl,imx7ulp-usbphy"; reg = <0x5b110000 0x1000>; clocks = <&usb2_2_lpcg IMX_LPCG_CLK_7>; diff --git a/arch/arm64/boot/dts/freescale/imx8mm-beacon-baseboard.dtsi b/arch/arm64/boot/dts/freescale/imx8mm-beacon-baseboard.dtsi index 169f047fbca5..bc531175ff76 100644 --- a/arch/arm64/boot/dts/freescale/imx8mm-beacon-baseboard.dtsi +++ b/arch/arm64/boot/dts/freescale/imx8mm-beacon-baseboard.dtsi @@ -241,9 +241,8 @@ pinctrl-names = "default"; pinctrl-0 = <&pinctrl_pcie0>; reset-gpio = <&gpio4 21 GPIO_ACTIVE_LOW>; - clocks = <&clk IMX8MM_CLK_PCIE1_ROOT>, <&clk IMX8MM_CLK_PCIE1_AUX>, - <&pcie0_refclk_gated>; - clock-names = "pcie", "pcie_aux", "pcie_bus"; + clocks = <&clk IMX8MM_CLK_PCIE1_ROOT>, <&pcie0_refclk_gated>, + <&clk IMX8MM_CLK_PCIE1_AUX>; assigned-clocks = <&clk IMX8MM_CLK_PCIE1_AUX>, <&clk IMX8MM_CLK_PCIE1_CTRL>; assigned-clock-rates = <10000000>, <250000000>; diff --git a/arch/arm64/boot/dts/freescale/imx8mm-data-modul-edm-sbc.dts b/arch/arm64/boot/dts/freescale/imx8mm-data-modul-edm-sbc.dts index 9889319d4f04..b1f2beb40a98 100644 --- a/arch/arm64/boot/dts/freescale/imx8mm-data-modul-edm-sbc.dts +++ b/arch/arm64/boot/dts/freescale/imx8mm-data-modul-edm-sbc.dts @@ -905,9 +905,8 @@ pinctrl-names = "default"; pinctrl-0 = <&pinctrl_pcie0>; reset-gpio = <&gpio1 5 GPIO_ACTIVE_LOW>; - clocks = <&clk IMX8MM_CLK_PCIE1_ROOT>, <&clk IMX8MM_CLK_PCIE1_AUX>, - <&pcieclk 0>; - clock-names = "pcie", "pcie_aux", "pcie_bus"; + clocks = <&clk IMX8MM_CLK_PCIE1_ROOT>, <&pcieclk 0>, + <&clk IMX8MM_CLK_PCIE1_AUX>; assigned-clocks = <&clk IMX8MM_CLK_PCIE1_AUX>, <&clk IMX8MM_CLK_PCIE1_CTRL>; assigned-clock-rates = <10000000>, <250000000>; diff --git a/arch/arm64/boot/dts/freescale/imx8mm-emcon.dtsi b/arch/arm64/boot/dts/freescale/imx8mm-emcon.dtsi index 0dbdc9ec3fe5..3d859a350bd5 100644 --- a/arch/arm64/boot/dts/freescale/imx8mm-emcon.dtsi +++ b/arch/arm64/boot/dts/freescale/imx8mm-emcon.dtsi @@ -18,14 +18,14 @@ pinctrl-names = "default"; pinctrl-0 = <&pinctrl_gpio_led>; - green { + led-green { label = "som:green"; gpios = <&gpio3 4 GPIO_ACTIVE_HIGH>; default-state = "on"; linux,default-trigger = "heartbeat"; }; - red { + led-red { label = "som:red"; gpios = <&gpio5 10 GPIO_ACTIVE_HIGH>; default-state = "off"; diff --git a/arch/arm64/boot/dts/freescale/imx8mm-evk.dtsi b/arch/arm64/boot/dts/freescale/imx8mm-evk.dtsi index e0b604ac0da4..d1a6390976a9 100644 --- a/arch/arm64/boot/dts/freescale/imx8mm-evk.dtsi +++ b/arch/arm64/boot/dts/freescale/imx8mm-evk.dtsi @@ -340,7 +340,7 @@ status = "okay"; pca6416: gpio@20 { - compatible = "ti,tca6416"; + compatible = "nxp,pca6416"; reg = <0x20>; gpio-controller; #gpio-cells = <2>; @@ -360,9 +360,8 @@ pinctrl-names = "default"; pinctrl-0 = <&pinctrl_pcie0>; reset-gpio = <&gpio4 21 GPIO_ACTIVE_LOW>; - clocks = <&clk IMX8MM_CLK_PCIE1_ROOT>, <&clk IMX8MM_CLK_PCIE1_AUX>, - <&pcie0_refclk>; - clock-names = "pcie", "pcie_aux", "pcie_bus"; + clocks = <&clk IMX8MM_CLK_PCIE1_ROOT>, <&pcie0_refclk>, + <&clk IMX8MM_CLK_PCIE1_AUX>; assigned-clocks = <&clk IMX8MM_CLK_PCIE1_AUX>, <&clk IMX8MM_CLK_PCIE1_CTRL>; assigned-clock-rates = <10000000>, <250000000>; diff --git a/arch/arm64/boot/dts/freescale/imx8mm-innocomm-wb15.dtsi b/arch/arm64/boot/dts/freescale/imx8mm-innocomm-wb15.dtsi index 44e87b1568e7..299752aa8277 100644 --- a/arch/arm64/boot/dts/freescale/imx8mm-innocomm-wb15.dtsi +++ b/arch/arm64/boot/dts/freescale/imx8mm-innocomm-wb15.dtsi @@ -210,9 +210,6 @@ pinctrl-names = "default"; pinctrl-0 = <&pinctrl_pcie0>; reset-gpio = <&gpio5 21 GPIO_ACTIVE_LOW>; - clocks = <&clk IMX8MM_CLK_PCIE1_ROOT>, <&clk IMX8MM_CLK_PCIE1_PHY>, - <&clk IMX8MM_CLK_PCIE1_AUX>; - clock-names = "pcie", "pcie_bus", "pcie_aux"; fsl,max-link-speed = <1>; assigned-clocks = <&clk IMX8MM_CLK_PCIE1_AUX>, <&clk IMX8MM_CLK_PCIE1_CTRL>; assigned-clock-rates = <10000000>, <250000000>; diff --git a/arch/arm64/boot/dts/freescale/imx8mm-kontron-bl.dts b/arch/arm64/boot/dts/freescale/imx8mm-kontron-bl.dts index a079322a3793..dcec57c20399 100644 --- a/arch/arm64/boot/dts/freescale/imx8mm-kontron-bl.dts +++ b/arch/arm64/boot/dts/freescale/imx8mm-kontron-bl.dts @@ -13,6 +13,8 @@ aliases { ethernet1 = &usbnet; + rtc0 = &rx8900; + rtc1 = &snvs_rtc; }; /* fixed crystal dedicated to mcp2515 */ @@ -136,7 +138,7 @@ pinctrl-0 = <&pinctrl_i2c4>; status = "okay"; - rtc@32 { + rx8900: rtc@32 { compatible = "epson,rx8900"; reg = <0x32>; }; diff --git a/arch/arm64/boot/dts/freescale/imx8mm-kontron-osm-s.dtsi b/arch/arm64/boot/dts/freescale/imx8mm-kontron-osm-s.dtsi index 5172883717d1..6e75ab879bf5 100644 --- a/arch/arm64/boot/dts/freescale/imx8mm-kontron-osm-s.dtsi +++ b/arch/arm64/boot/dts/freescale/imx8mm-kontron-osm-s.dtsi @@ -10,6 +10,11 @@ model = "Kontron OSM-S i.MX8MM (N802X SOM)"; compatible = "kontron,imx8mm-osm-s", "fsl,imx8mm"; + aliases { + rtc0 = &rv3028; + rtc1 = &snvs_rtc; + }; + memory@40000000 { device_type = "memory"; /* @@ -200,7 +205,7 @@ }; }; - rtc@52 { + rv3028: rtc@52 { compatible = "microcrystal,rv3028"; reg = <0x52>; pinctrl-names = "default"; diff --git a/arch/arm64/boot/dts/freescale/imx8mm-mx8menlo.dts b/arch/arm64/boot/dts/freescale/imx8mm-mx8menlo.dts index 43e89859c044..0b123a84018b 100644 --- a/arch/arm64/boot/dts/freescale/imx8mm-mx8menlo.dts +++ b/arch/arm64/boot/dts/freescale/imx8mm-mx8menlo.dts @@ -10,6 +10,7 @@ / { model = "MENLO MX8MM EMBEDDED DEVICE"; compatible = "menlo,mx8menlo", + "toradex,verdin-imx8mm-nonwifi", "toradex,verdin-imx8mm", "fsl,imx8mm"; diff --git a/arch/arm64/boot/dts/freescale/imx8mm-phyboard-polis-rdk.dts b/arch/arm64/boot/dts/freescale/imx8mm-phyboard-polis-rdk.dts index 4a3df2b77b0b..266129b4a70d 100644 --- a/arch/arm64/boot/dts/freescale/imx8mm-phyboard-polis-rdk.dts +++ b/arch/arm64/boot/dts/freescale/imx8mm-phyboard-polis-rdk.dts @@ -175,9 +175,6 @@ assigned-clock-parents = <&clk IMX8MM_SYS_PLL2_50M>, <&clk IMX8MM_SYS_PLL2_250M>; assigned-clock-rates = <10000000>, <250000000>; - clocks = <&clk IMX8MM_CLK_PCIE1_ROOT>, <&clk IMX8MM_CLK_PCIE1_AUX>, - <&clk IMX8MM_CLK_PCIE1_PHY>; - clock-names = "pcie", "pcie_aux", "pcie_bus"; pinctrl-names = "default"; pinctrl-0 = <&pinctrl_pcie>; reset-gpio = <&gpio4 9 GPIO_ACTIVE_LOW>; diff --git a/arch/arm64/boot/dts/freescale/imx8mm-tqma8mqml-mba8mx.dts b/arch/arm64/boot/dts/freescale/imx8mm-tqma8mqml-mba8mx.dts index a0aeac619929..156d793a0c97 100644 --- a/arch/arm64/boot/dts/freescale/imx8mm-tqma8mqml-mba8mx.dts +++ b/arch/arm64/boot/dts/freescale/imx8mm-tqma8mqml-mba8mx.dts @@ -79,9 +79,8 @@ &pcie0 { reset-gpio = <&expander0 14 GPIO_ACTIVE_LOW>; - clocks = <&clk IMX8MM_CLK_PCIE1_ROOT>, <&clk IMX8MM_CLK_PCIE1_AUX>, - <&pcie0_refclk>; - clock-names = "pcie", "pcie_aux", "pcie_bus"; + clocks = <&clk IMX8MM_CLK_PCIE1_ROOT>, <&pcie0_refclk>, + <&clk IMX8MM_CLK_PCIE1_AUX>; assigned-clocks = <&clk IMX8MM_CLK_PCIE1_AUX>, <&clk IMX8MM_CLK_PCIE1_CTRL>; assigned-clock-rates = <10000000>, <250000000>; diff --git a/arch/arm64/boot/dts/freescale/imx8mm-tqma8mqml.dtsi b/arch/arm64/boot/dts/freescale/imx8mm-tqma8mqml.dtsi index f649dfacb4b6..12260290c109 100644 --- a/arch/arm64/boot/dts/freescale/imx8mm-tqma8mqml.dtsi +++ b/arch/arm64/boot/dts/freescale/imx8mm-tqma8mqml.dtsi @@ -87,8 +87,8 @@ sda-gpios = <&gpio5 15 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>; status = "okay"; - sensor0: temperature-sensor-eeprom@1b { - compatible = "nxp,se97", "jedec,jc-42.4-temp"; + sensor0: temperature-sensor@1b { + compatible = "nxp,se97b", "jedec,jc-42.4-temp"; reg = <0x1b>; }; diff --git a/arch/arm64/boot/dts/freescale/imx8mm-var-som.dtsi b/arch/arm64/boot/dts/freescale/imx8mm-var-som.dtsi index ae0721b807e1..2b83a5258ec6 100644 --- a/arch/arm64/boot/dts/freescale/imx8mm-var-som.dtsi +++ b/arch/arm64/boot/dts/freescale/imx8mm-var-som.dtsi @@ -231,7 +231,6 @@ }; ldo5_reg: LDO5 { - regulator-compatible = "ldo5"; regulator-min-microvolt = <1800000>; regulator-max-microvolt = <1800000>; regulator-always-on; diff --git a/arch/arm64/boot/dts/freescale/imx8mm-venice-gw71xx.dtsi b/arch/arm64/boot/dts/freescale/imx8mm-venice-gw71xx.dtsi index c557dbf4dcd6..0ce60ad9c7d5 100644 --- a/arch/arm64/boot/dts/freescale/imx8mm-venice-gw71xx.dtsi +++ b/arch/arm64/boot/dts/freescale/imx8mm-venice-gw71xx.dtsi @@ -120,9 +120,8 @@ pinctrl-names = "default"; pinctrl-0 = <&pinctrl_pcie0>; reset-gpio = <&gpio4 6 GPIO_ACTIVE_LOW>; - clocks = <&clk IMX8MM_CLK_PCIE1_ROOT>, <&clk IMX8MM_CLK_PCIE1_AUX>, - <&pcie0_refclk>; - clock-names = "pcie", "pcie_aux", "pcie_bus"; + clocks = <&clk IMX8MM_CLK_PCIE1_ROOT>, <&pcie0_refclk>, + <&clk IMX8MM_CLK_PCIE1_AUX>; assigned-clocks = <&clk IMX8MM_CLK_PCIE1_AUX>, <&clk IMX8MM_CLK_PCIE1_CTRL>; assigned-clock-rates = <10000000>, <250000000>; diff --git a/arch/arm64/boot/dts/freescale/imx8mm-venice-gw72xx.dtsi b/arch/arm64/boot/dts/freescale/imx8mm-venice-gw72xx.dtsi index 41d0de6a7027..570992a52b75 100644 --- a/arch/arm64/boot/dts/freescale/imx8mm-venice-gw72xx.dtsi +++ b/arch/arm64/boot/dts/freescale/imx8mm-venice-gw72xx.dtsi @@ -142,9 +142,8 @@ pinctrl-names = "default"; pinctrl-0 = <&pinctrl_pcie0>; reset-gpio = <&gpio4 6 GPIO_ACTIVE_LOW>; - clocks = <&clk IMX8MM_CLK_PCIE1_ROOT>, <&clk IMX8MM_CLK_PCIE1_AUX>, - <&pcie0_refclk>; - clock-names = "pcie", "pcie_aux", "pcie_bus"; + clocks = <&clk IMX8MM_CLK_PCIE1_ROOT>, <&pcie0_refclk>, + <&clk IMX8MM_CLK_PCIE1_AUX>; assigned-clocks = <&clk IMX8MM_CLK_PCIE1_AUX>, <&clk IMX8MM_CLK_PCIE1_CTRL>; assigned-clock-rates = <10000000>, <250000000>; diff --git a/arch/arm64/boot/dts/freescale/imx8mm-venice-gw73xx.dtsi b/arch/arm64/boot/dts/freescale/imx8mm-venice-gw73xx.dtsi index 7761d5671cb1..1800c6a4b1fc 100644 --- a/arch/arm64/boot/dts/freescale/imx8mm-venice-gw73xx.dtsi +++ b/arch/arm64/boot/dts/freescale/imx8mm-venice-gw73xx.dtsi @@ -162,9 +162,8 @@ pinctrl-names = "default"; pinctrl-0 = <&pinctrl_pcie0>; reset-gpio = <&gpio4 6 GPIO_ACTIVE_LOW>; - clocks = <&clk IMX8MM_CLK_PCIE1_ROOT>, <&clk IMX8MM_CLK_PCIE1_AUX>, - <&pcie0_refclk>; - clock-names = "pcie", "pcie_aux", "pcie_bus"; + clocks = <&clk IMX8MM_CLK_PCIE1_ROOT>, <&pcie0_refclk>, + <&clk IMX8MM_CLK_PCIE1_AUX>; assigned-clocks = <&clk IMX8MM_CLK_PCIE1_AUX>, <&clk IMX8MM_CLK_PCIE1_CTRL>; assigned-clock-rates = <10000000>, <250000000>; diff --git a/arch/arm64/boot/dts/freescale/imx8mm-venice-gw7901.dts b/arch/arm64/boot/dts/freescale/imx8mm-venice-gw7901.dts index 64b366e83fa1..df3b2c93d2d5 100644 --- a/arch/arm64/boot/dts/freescale/imx8mm-venice-gw7901.dts +++ b/arch/arm64/boot/dts/freescale/imx8mm-venice-gw7901.dts @@ -702,9 +702,8 @@ pinctrl-names = "default"; pinctrl-0 = <&pinctrl_pcie0>; reset-gpio = <&gpio5 2 GPIO_ACTIVE_LOW>; - clocks = <&clk IMX8MM_CLK_PCIE1_ROOT>, <&clk IMX8MM_CLK_PCIE1_AUX>, - <&pcie0_refclk>; - clock-names = "pcie", "pcie_aux", "pcie_bus"; + clocks = <&clk IMX8MM_CLK_PCIE1_ROOT>, <&pcie0_refclk>, + <&clk IMX8MM_CLK_PCIE1_AUX>; assigned-clocks = <&clk IMX8MM_CLK_PCIE1_AUX>, <&clk IMX8MM_CLK_PCIE1_CTRL>; assigned-clock-rates = <10000000>, <250000000>; diff --git a/arch/arm64/boot/dts/freescale/imx8mm-venice-gw7902.dts b/arch/arm64/boot/dts/freescale/imx8mm-venice-gw7902.dts index e8bc1fccc47b..c33ec6826d32 100644 --- a/arch/arm64/boot/dts/freescale/imx8mm-venice-gw7902.dts +++ b/arch/arm64/boot/dts/freescale/imx8mm-venice-gw7902.dts @@ -623,9 +623,8 @@ pinctrl-names = "default"; pinctrl-0 = <&pinctrl_pcie0>; reset-gpio = <&gpio4 5 GPIO_ACTIVE_LOW>; - clocks = <&clk IMX8MM_CLK_PCIE1_ROOT>, <&clk IMX8MM_CLK_PCIE1_AUX>, - <&pcie0_refclk>; - clock-names = "pcie", "pcie_aux", "pcie_bus"; + clocks = <&clk IMX8MM_CLK_PCIE1_ROOT>, <&pcie0_refclk>, + <&clk IMX8MM_CLK_PCIE1_AUX>; assigned-clocks = <&clk IMX8MM_CLK_PCIE1_AUX>, <&clk IMX8MM_CLK_PCIE1_CTRL>; assigned-clock-rates = <10000000>, <250000000>; diff --git a/arch/arm64/boot/dts/freescale/imx8mm-venice-gw7903.dts b/arch/arm64/boot/dts/freescale/imx8mm-venice-gw7903.dts index acc2ba8e00a8..363020a08c9b 100644 --- a/arch/arm64/boot/dts/freescale/imx8mm-venice-gw7903.dts +++ b/arch/arm64/boot/dts/freescale/imx8mm-venice-gw7903.dts @@ -557,9 +557,8 @@ pinctrl-names = "default"; pinctrl-0 = <&pinctrl_pcie0>; reset-gpio = <&gpio5 11 GPIO_ACTIVE_LOW>; - clocks = <&clk IMX8MM_CLK_PCIE1_ROOT>, <&clk IMX8MM_CLK_PCIE1_AUX>, - <&pcie0_refclk>; - clock-names = "pcie", "pcie_aux", "pcie_bus"; + clocks = <&clk IMX8MM_CLK_PCIE1_ROOT>, <&pcie0_refclk>, + <&clk IMX8MM_CLK_PCIE1_AUX>; assigned-clocks = <&clk IMX8MM_CLK_PCIE1_AUX>, <&clk IMX8MM_CLK_PCIE1_CTRL>; assigned-clock-rates = <10000000>, <250000000>; diff --git a/arch/arm64/boot/dts/freescale/imx8mm-venice-gw7904.dts b/arch/arm64/boot/dts/freescale/imx8mm-venice-gw7904.dts index eceed9816f5d..93088fa1c3b9 100644 --- a/arch/arm64/boot/dts/freescale/imx8mm-venice-gw7904.dts +++ b/arch/arm64/boot/dts/freescale/imx8mm-venice-gw7904.dts @@ -618,9 +618,8 @@ pinctrl-names = "default"; pinctrl-0 = <&pinctrl_pcie0>; reset-gpio = <&gpio5 11 GPIO_ACTIVE_LOW>; - clocks = <&clk IMX8MM_CLK_PCIE1_ROOT>, <&clk IMX8MM_CLK_PCIE1_AUX>, - <&pcie0_refclk>; - clock-names = "pcie", "pcie_aux", "pcie_bus"; + clocks = <&clk IMX8MM_CLK_PCIE1_ROOT>, <&pcie0_refclk>, + <&clk IMX8MM_CLK_PCIE1_AUX>; assigned-clocks = <&clk IMX8MM_CLK_PCIE1_AUX>, <&clk IMX8MM_CLK_PCIE1_CTRL>; assigned-clock-rates = <10000000>, <250000000>; diff --git a/arch/arm64/boot/dts/freescale/imx8mm-verdin-dahlia.dtsi b/arch/arm64/boot/dts/freescale/imx8mm-verdin-dahlia.dtsi index 7c3f5c54f040..1cff0b829357 100644 --- a/arch/arm64/boot/dts/freescale/imx8mm-verdin-dahlia.dtsi +++ b/arch/arm64/boot/dts/freescale/imx8mm-verdin-dahlia.dtsi @@ -137,11 +137,13 @@ /* Verdin USB_1 */ &usbotg1 { + disable-over-current; status = "okay"; }; /* Verdin USB_2 */ &usbotg2 { + disable-over-current; status = "okay"; }; diff --git a/arch/arm64/boot/dts/freescale/imx8mm-verdin-dev.dtsi b/arch/arm64/boot/dts/freescale/imx8mm-verdin-dev.dtsi index b2bcd2282170..3c4b8ca125e3 100644 --- a/arch/arm64/boot/dts/freescale/imx8mm-verdin-dev.dtsi +++ b/arch/arm64/boot/dts/freescale/imx8mm-verdin-dev.dtsi @@ -3,8 +3,6 @@ * Copyright 2022 Toradex */ -#include "imx8mm-verdin-dahlia.dtsi" - / { sound_card: sound-card { compatible = "simple-audio-card"; @@ -42,27 +40,121 @@ }; }; +/* Verdin SPI_1 */ +&ecspi2 { + status = "okay"; +}; + +/* EEPROM on display adapter boards */ +&eeprom_display_adapter { + status = "okay"; +}; + +/* EEPROM on Verdin Development board */ +&eeprom_carrier_board { + status = "okay"; +}; + +&fec1 { + status = "okay"; +}; + +/* Verdin QSPI_1 */ +&flexspi { + status = "okay"; +}; + +/* Current measurement into module VCC */ +&hwmon { + status = "okay"; +}; + +&hwmon_temp { + vs-supply = <®_1p8v>; + status = "okay"; +}; + +&i2c3 { + status = "okay"; +}; + &gpio_expander_21 { status = "okay"; }; /* Verdin I2C_1 */ &i2c4 { + status = "okay"; + /* Audio Codec */ nau8822_1a: audio-codec@1a { compatible = "nuvoton,nau8822"; reg = <0x1a>; + #sound-dai-cells = <0>; }; }; +/* Verdin PCIE_1 */ +&pcie0 { + status = "okay"; +}; + +&pcie_phy { + status = "okay"; +}; + +/* Verdin PWM_3_DSI */ +&pwm1 { + status = "okay"; +}; + +/* Verdin PWM_1 */ +&pwm2 { + status = "okay"; +}; + +/* Verdin PWM_2 */ +&pwm3 { + status = "okay"; +}; + +/* Verdin I2S_1 */ +&sai2 { + status = "okay"; +}; + +/* Verdin UART_3 */ +&uart1 { + status = "okay"; +}; + /* Verdin UART_1, connector X50 through RS485 transceiver */ &uart2 { linux,rs485-enabled-at-boot-time; rs485-rts-active-low; rs485-rx-during-tx; + status = "okay"; +}; + +/* Verdin UART_2 */ +&uart3 { + status = "okay"; +}; + +/* Verdin USB_1 */ +&usbotg1 { + disable-over-current; + status = "okay"; +}; + +/* Verdin USB_2 */ +&usbotg2 { + disable-over-current; + status = "okay"; }; /* Limit frequency on dev board due to long traces and bad signal integrity */ &usdhc2 { max-frequency = <100000000>; + status = "okay"; }; diff --git a/arch/arm64/boot/dts/freescale/imx8mm-verdin-nonwifi-yavia.dts b/arch/arm64/boot/dts/freescale/imx8mm-verdin-nonwifi-yavia.dts new file mode 100644 index 000000000000..c71825ecf2ea --- /dev/null +++ b/arch/arm64/boot/dts/freescale/imx8mm-verdin-nonwifi-yavia.dts @@ -0,0 +1,18 @@ +// SPDX-License-Identifier: GPL-2.0-or-later OR MIT +/* + * Copyright 2023 Toradex + */ + +/dts-v1/; + +#include "imx8mm-verdin.dtsi" +#include "imx8mm-verdin-nonwifi.dtsi" +#include "imx8mm-verdin-yavia.dtsi" + +/ { + model = "Toradex Verdin iMX8M Mini on Yavia Board"; + compatible = "toradex,verdin-imx8mm-nonwifi-yavia", + "toradex,verdin-imx8mm-nonwifi", + "toradex,verdin-imx8mm", + "fsl,imx8mm"; +}; diff --git a/arch/arm64/boot/dts/freescale/imx8mm-verdin-wifi-yavia.dts b/arch/arm64/boot/dts/freescale/imx8mm-verdin-wifi-yavia.dts new file mode 100644 index 000000000000..fe39de9310d6 --- /dev/null +++ b/arch/arm64/boot/dts/freescale/imx8mm-verdin-wifi-yavia.dts @@ -0,0 +1,18 @@ +// SPDX-License-Identifier: GPL-2.0-or-later OR MIT +/* + * Copyright 2023 Toradex + */ + +/dts-v1/; + +#include "imx8mm-verdin.dtsi" +#include "imx8mm-verdin-wifi.dtsi" +#include "imx8mm-verdin-yavia.dtsi" + +/ { + model = "Toradex Verdin iMX8M Mini WB on Yavia Board"; + compatible = "toradex,verdin-imx8mm-wifi-yavia", + "toradex,verdin-imx8mm-wifi", + "toradex,verdin-imx8mm", + "fsl,imx8mm"; +}; diff --git a/arch/arm64/boot/dts/freescale/imx8mm-verdin-yavia.dtsi b/arch/arm64/boot/dts/freescale/imx8mm-verdin-yavia.dtsi new file mode 100644 index 000000000000..1e28c78e381f --- /dev/null +++ b/arch/arm64/boot/dts/freescale/imx8mm-verdin-yavia.dtsi @@ -0,0 +1,169 @@ +// SPDX-License-Identifier: GPL-2.0-or-later OR MIT +/* + * Copyright 2023 Toradex + */ + +#include <dt-bindings/leds/common.h> + +/ { + leds { + compatible = "gpio-leds"; + + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_leds_yavia>; + + /* SODIMM 52 - LD1_RED */ + led-0 { + color = <LED_COLOR_ID_RED>; + function = LED_FUNCTION_DEBUG; + function-enumerator = <1>; + gpios = <&gpio3 0 GPIO_ACTIVE_HIGH>; + }; + /* SODIMM 54 - LD1_GREEN */ + led-1 { + color = <LED_COLOR_ID_GREEN>; + function = LED_FUNCTION_DEBUG; + function-enumerator = <1>; + gpios = <&gpio3 1 GPIO_ACTIVE_HIGH>; + }; + /* SODIMM 56 - LD1_BLUE */ + led-2 { + color = <LED_COLOR_ID_BLUE>; + function = LED_FUNCTION_DEBUG; + function-enumerator = <1>; + gpios = <&gpio3 6 GPIO_ACTIVE_HIGH>; + }; + /* SODIMM 58 - LD2_RED */ + led-3 { + color = <LED_COLOR_ID_RED>; + function = LED_FUNCTION_DEBUG; + function-enumerator = <2>; + gpios = <&gpio3 7 GPIO_ACTIVE_HIGH>; + }; + /* SODIMM 60 - LD2_GREEN */ + led-4 { + color = <LED_COLOR_ID_GREEN>; + function = LED_FUNCTION_DEBUG; + function-enumerator = <2>; + gpios = <&gpio3 8 GPIO_ACTIVE_HIGH>; + }; + /* SODIMM 62 - LD2_BLUE */ + led-5 { + color = <LED_COLOR_ID_BLUE>; + function = LED_FUNCTION_DEBUG; + function-enumerator = <2>; + gpios = <&gpio3 9 GPIO_ACTIVE_HIGH>; + }; + }; +}; + +/* Verdin SPI_1 */ +&ecspi2 { + status = "okay"; +}; + +/* EEPROM on display adapter boards */ +&eeprom_display_adapter { + status = "okay"; +}; + +/* EEPROM on Verdin yavia board */ +&eeprom_carrier_board { + status = "okay"; +}; + +&fec1 { + status = "okay"; +}; + +&gpio3 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_gpios_ext_yavia>; +}; + +&hwmon_temp { + status = "okay"; +}; + +&i2c3 { + status = "okay"; +}; + +/* Verdin I2C_1 */ +&i2c4 { + status = "okay"; +}; + +/* Verdin PCIE_1 */ +&pcie0 { + status = "okay"; +}; + +&pcie_phy { + status = "okay"; +}; + +/* Verdin PWM_3_DSI */ +&pwm1 { + status = "okay"; +}; + +/* Verdin PWM_1 */ +&pwm2 { + status = "okay"; +}; + +/* Verdin PWM_2 */ +&pwm3 { + status = "okay"; +}; + +/* Verdin UART_3 */ +&uart1 { + status = "okay"; +}; + +/* Verdin UART_1 */ +&uart2 { + status = "okay"; +}; + +/* Verdin UART_2 */ +&uart3 { + status = "okay"; +}; + +/* Verdin USB_1 */ +&usbotg1 { + status = "okay"; +}; + +/* Verdin USB_2 */ +&usbotg2 { + status = "okay"; +}; + +/* Verdin SD_1 */ +&usdhc2 { + status = "okay"; +}; + +&iomuxc { + pinctrl_leds_yavia: ledsyaviagrp { + fsl,pins = < + MX8MM_IOMUXC_NAND_ALE_GPIO3_IO0 0x106 /* SODIMM 52 */ + MX8MM_IOMUXC_NAND_CE0_B_GPIO3_IO1 0x106 /* SODIMM 54 */ + MX8MM_IOMUXC_NAND_DATA00_GPIO3_IO6 0x106 /* SODIMM 56 */ + MX8MM_IOMUXC_NAND_DATA01_GPIO3_IO7 0x106 /* SODIMM 58 */ + MX8MM_IOMUXC_NAND_DATA02_GPIO3_IO8 0x106 /* SODIMM 60 */ + MX8MM_IOMUXC_NAND_DATA03_GPIO3_IO9 0x106 /* SODIMM 62 */ + >; + }; + + pinctrl_gpios_ext_yavia: gpiosextyaviagrp { + fsl,pins = < + MX8MM_IOMUXC_NAND_CE1_B_GPIO3_IO2 0x106 /* SODIMM 64 */ + MX8MM_IOMUXC_NAND_DQS_GPIO3_IO14 0x106 /* SODIMM 66 */ + >; + }; +}; diff --git a/arch/arm64/boot/dts/freescale/imx8mm-verdin.dtsi b/arch/arm64/boot/dts/freescale/imx8mm-verdin.dtsi index 702d87621bb4..88321b5b0693 100644 --- a/arch/arm64/boot/dts/freescale/imx8mm-verdin.dtsi +++ b/arch/arm64/boot/dts/freescale/imx8mm-verdin.dtsi @@ -56,7 +56,11 @@ hdmi_connector: hdmi-connector { compatible = "hdmi-connector"; ddc-i2c-bus = <&i2c2>; + /* Verdin PWM_3_DSI (SODIMM 19) */ + hpd-gpios = <&gpio1 1 GPIO_ACTIVE_HIGH>; label = "hdmi"; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_pwm_3_dsi_hpd_gpio>; type = "a"; status = "disabled"; }; @@ -359,7 +363,6 @@ pinctrl-names = "default"; pinctrl-0 = <&pinctrl_pmic>; reg = <0x25>; - sd-vsel-gpios = <&gpio1 4 GPIO_ACTIVE_HIGH>; /* * The bootloader is expected to switch on the I2C level shifter for the TLA2024 ADC @@ -599,7 +602,7 @@ hdmi_lontium_lt8912: hdmi@48 { compatible = "lontium,lt8912b"; pinctrl-names = "default"; - pinctrl-0 = <&pinctrl_gpio_10_dsi>, <&pinctrl_pwm_3_dsi_hpd_gpio>; + pinctrl-0 = <&pinctrl_gpio_10_dsi>; reg = <0x48>; /* Verdin GPIO_9_DSI (LT8912 INT, SODIMM 17, unused) */ /* Verdin GPIO_10_DSI (SODIMM 21) */ @@ -654,10 +657,6 @@ assigned-clock-parents = <&clk IMX8MM_SYS_PLL2_50M>, <&clk IMX8MM_SYS_PLL2_250M>; assigned-clock-rates = <10000000>, <250000000>; - clocks = <&clk IMX8MM_CLK_PCIE1_ROOT>, - <&clk IMX8MM_CLK_PCIE1_AUX>, - <&clk IMX8MM_CLK_PCIE1_PHY>; - clock-names = "pcie", "pcie_aux", "pcie_bus"; pinctrl-names = "default"; pinctrl-0 = <&pinctrl_pcie0>; /* PCIE_1_RESET# (SODIMM 244) */ @@ -742,7 +741,6 @@ adp-disable; dr_mode = "otg"; hnp-disable; - over-current-active-low; samsung,picophy-dc-vol-level-adjust = <7>; samsung,picophy-pre-emp-curr-control = <3>; srp-disable; @@ -752,7 +750,6 @@ /* Verdin USB_2 */ &usbotg2 { dr_mode = "host"; - over-current-active-low; samsung,picophy-dc-vol-level-adjust = <7>; samsung,picophy-pre-emp-curr-control = <3>; vbus-supply = <®_usb_otg2_vbus>; diff --git a/arch/arm64/boot/dts/freescale/imx8mm.dtsi b/arch/arm64/boot/dts/freescale/imx8mm.dtsi index 4ee89fdcf59b..31f4548f85cf 100644 --- a/arch/arm64/boot/dts/freescale/imx8mm.dtsi +++ b/arch/arm64/boot/dts/freescale/imx8mm.dtsi @@ -496,6 +496,8 @@ compatible = "fsl,imx8mm-tmu"; reg = <0x30260000 0x10000>; clocks = <&clk IMX8MM_CLK_TMU_ROOT>; + nvmem-cells = <&tmu_calib>; + nvmem-cell-names = "calib"; #thermal-sensor-cells = <0>; }; @@ -550,8 +552,8 @@ reg = <0x30330000 0x10000>; }; - gpr: iomuxc-gpr@30340000 { - compatible = "fsl,imx8mm-iomuxc-gpr", "fsl,imx6q-iomuxc-gpr", "syscon"; + gpr: syscon@30340000 { + compatible = "fsl,imx8mm-iomuxc-gpr", "syscon"; reg = <0x30340000 0x10000>; }; @@ -563,15 +565,32 @@ #address-cells = <1>; #size-cells = <1>; - imx8mm_uid: unique-id@410 { + /* + * The register address below maps to the MX8M + * Fusemap Description Table entries this way. + * Assuming + * reg = <ADDR SIZE>; + * then + * Fuse Address = (ADDR * 4) + 0x400 + * Note that if SIZE is greater than 4, then + * each subsequent fuse is located at offset + * +0x10 in Fusemap Description Table (e.g. + * reg = <0x4 0x8> describes fuses 0x410 and + * 0x420). + */ + imx8mm_uid: unique-id@4 { /* 0x410-0x420 */ reg = <0x4 0x8>; }; - cpu_speed_grade: speed-grade@10 { + cpu_speed_grade: speed-grade@10 { /* 0x440 */ reg = <0x10 4>; }; - fec_mac_address: mac-address@90 { + tmu_calib: calib@3c { /* 0x4f0 */ + reg = <0x3c 4>; + }; + + fec_mac_address: mac-address@90 { /* 0x640 */ reg = <0x90 6>; }; }; @@ -1240,7 +1259,6 @@ <GIC_SPI 12 IRQ_TYPE_LEVEL_HIGH>, <GIC_SPI 12 IRQ_TYPE_LEVEL_HIGH>, <GIC_SPI 12 IRQ_TYPE_LEVEL_HIGH>; - interrupt-names = "gpmi0", "gpmi1", "gpmi2", "gpmi3"; #dma-cells = <1>; dma-channels = <4>; clocks = <&clk IMX8MM_CLK_NAND_USDHC_BUS_RAWNAND_CLK>; @@ -1284,6 +1302,10 @@ <0 0 0 4 &gic GIC_SPI 122 IRQ_TYPE_LEVEL_HIGH>; fsl,max-link-speed = <2>; linux,pci-domain = <0>; + clocks = <&clk IMX8MM_CLK_PCIE1_ROOT>, + <&clk IMX8MM_CLK_PCIE1_PHY>, + <&clk IMX8MM_CLK_PCIE1_AUX>; + clock-names = "pcie", "pcie_bus", "pcie_aux"; power-domains = <&pgc_pcie>; resets = <&src IMX8MQ_RESET_PCIE_CTRL_APPS_EN>, <&src IMX8MQ_RESET_PCIE_CTRL_APPS_TURNOFF>; diff --git a/arch/arm64/boot/dts/freescale/imx8mn-tqma8mqnl.dtsi b/arch/arm64/boot/dts/freescale/imx8mn-tqma8mqnl.dtsi index 9ea28941068d..31ae338b7ed9 100644 --- a/arch/arm64/boot/dts/freescale/imx8mn-tqma8mqnl.dtsi +++ b/arch/arm64/boot/dts/freescale/imx8mn-tqma8mqnl.dtsi @@ -77,8 +77,8 @@ sda-gpios = <&gpio5 15 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>; status = "okay"; - sensor0: temperature-sensor-eeprom@1b { - compatible = "nxp,se97", "jedec,jc-42.4-temp"; + sensor0: temperature-sensor@1b { + compatible = "nxp,se97b", "jedec,jc-42.4-temp"; reg = <0x1b>; }; diff --git a/arch/arm64/boot/dts/freescale/imx8mn-var-som.dtsi b/arch/arm64/boot/dts/freescale/imx8mn-var-som.dtsi index 87b5e23c766f..67072e6c77d5 100644 --- a/arch/arm64/boot/dts/freescale/imx8mn-var-som.dtsi +++ b/arch/arm64/boot/dts/freescale/imx8mn-var-som.dtsi @@ -207,7 +207,7 @@ }; ldo5_reg: LDO5 { - regulator-compatible = "ldo5"; + regulator-name = "ldo5"; regulator-min-microvolt = <1800000>; regulator-max-microvolt = <1800000>; regulator-always-on; diff --git a/arch/arm64/boot/dts/freescale/imx8mn.dtsi b/arch/arm64/boot/dts/freescale/imx8mn.dtsi index b7d91df71cc2..ed9ac6c5047c 100644 --- a/arch/arm64/boot/dts/freescale/imx8mn.dtsi +++ b/arch/arm64/boot/dts/freescale/imx8mn.dtsi @@ -498,6 +498,8 @@ compatible = "fsl,imx8mn-tmu", "fsl,imx8mm-tmu"; reg = <0x30260000 0x10000>; clocks = <&clk IMX8MN_CLK_TMU_ROOT>; + nvmem-cells = <&tmu_calib>; + nvmem-cell-names = "calib"; #thermal-sensor-cells = <0>; }; @@ -552,7 +554,7 @@ reg = <0x30330000 0x10000>; }; - gpr: iomuxc-gpr@30340000 { + gpr: syscon@30340000 { compatible = "fsl,imx8mn-iomuxc-gpr", "syscon"; reg = <0x30340000 0x10000>; }; @@ -564,15 +566,32 @@ #address-cells = <1>; #size-cells = <1>; - imx8mn_uid: unique-id@410 { + /* + * The register address below maps to the MX8M + * Fusemap Description Table entries this way. + * Assuming + * reg = <ADDR SIZE>; + * then + * Fuse Address = (ADDR * 4) + 0x400 + * Note that if SIZE is greater than 4, then + * each subsequent fuse is located at offset + * +0x10 in Fusemap Description Table (e.g. + * reg = <0x4 0x8> describes fuses 0x410 and + * 0x420). + */ + imx8mn_uid: unique-id@4 { /* 0x410-0x420 */ reg = <0x4 0x8>; }; - cpu_speed_grade: speed-grade@10 { + cpu_speed_grade: speed-grade@10 { /* 0x440 */ reg = <0x10 4>; }; - fec_mac_address: mac-address@90 { + tmu_calib: calib@3c { /* 0x4f0 */ + reg = <0x3c 4>; + }; + + fec_mac_address: mac-address@90 { /* 0x640 */ reg = <0x90 6>; }; }; @@ -1094,7 +1113,6 @@ <GIC_SPI 12 IRQ_TYPE_LEVEL_HIGH>, <GIC_SPI 12 IRQ_TYPE_LEVEL_HIGH>, <GIC_SPI 12 IRQ_TYPE_LEVEL_HIGH>; - interrupt-names = "gpmi0", "gpmi1", "gpmi2", "gpmi3"; #dma-cells = <1>; dma-channels = <4>; clocks = <&clk IMX8MN_CLK_NAND_USDHC_BUS_RAWNAND_CLK>; diff --git a/arch/arm64/boot/dts/freescale/imx8mp-beacon-kit.dts b/arch/arm64/boot/dts/freescale/imx8mp-beacon-kit.dts new file mode 100644 index 000000000000..cdae45a48c2c --- /dev/null +++ b/arch/arm64/boot/dts/freescale/imx8mp-beacon-kit.dts @@ -0,0 +1,550 @@ +// SPDX-License-Identifier: (GPL-2.0+ OR MIT) +/* + * Copyright 2023 Logic PD, Inc dba Beacon EmbeddedWorks + */ + +/dts-v1/; + +#include <dt-bindings/usb/pd.h> +#include <dt-bindings/phy/phy-imx8-pcie.h> +#include "imx8mp.dtsi" +#include "imx8mp-beacon-som.dtsi" + +/ { + model = "Beacon EmbeddedWorks i.MX8MPlus Development kit"; + compatible = "beacon,imx8mp-beacon-kit", "fsl,imx8mp"; + + aliases { + ethernet0 = &eqos; + ethernet1 = &fec; + }; + + chosen { + stdout-path = &uart2; + }; + + connector { + compatible = "usb-c-connector"; + label = "USB-C"; + data-role = "dual"; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + + hs_ep: endpoint { + remote-endpoint = <&usb3_hs_ep>; + }; + }; + port@1 { + reg = <1>; + + ss_ep: endpoint { + remote-endpoint = <&hd3ss3220_in_ep>; + }; + }; + }; + }; + + gpio-keys { + compatible = "gpio-keys"; + autorepeat; + + button-0 { + label = "btn0"; + linux,code = <BTN_0>; + gpios = <&pca6416_1 12 (GPIO_ACTIVE_LOW | GPIO_PULL_UP)>; + wakeup-source; + }; + + button-1 { + label = "btn1"; + linux,code = <BTN_1>; + gpios = <&pca6416_1 13 (GPIO_ACTIVE_LOW | GPIO_PULL_UP)>; + wakeup-source; + }; + + button-2 { + label = "btn2"; + linux,code = <BTN_2>; + gpios = <&pca6416_1 14 (GPIO_ACTIVE_LOW | GPIO_PULL_UP)>; + wakeup-source; + }; + + button-3 { + label = "btn3"; + linux,code = <BTN_3>; + gpios = <&pca6416_1 15 (GPIO_ACTIVE_LOW | GPIO_PULL_UP)>; + wakeup-source; + }; + }; + + leds { + compatible = "gpio-leds"; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_led3>; + + led-0 { + label = "gen_led0"; + gpios = <&pca6416_1 4 GPIO_ACTIVE_HIGH>; + default-state = "off"; + }; + + led-1 { + label = "gen_led1"; + gpios = <&pca6416_1 5 GPIO_ACTIVE_HIGH>; + default-state = "off"; + }; + + led-2 { + label = "gen_led2"; + gpios = <&pca6416_1 6 GPIO_ACTIVE_HIGH>; + default-state = "off"; + }; + + led-3 { + label = "heartbeat"; + gpios = <&gpio4 28 GPIO_ACTIVE_HIGH>; + linux,default-trigger = "heartbeat"; + }; + }; + + pcie0_refclk: clock-pcie { + compatible = "fixed-clock"; + #clock-cells = <0>; + clock-frequency = <100000000>; + }; + + reg_usdhc2_vmmc: regulator-usdhc2 { + compatible = "regulator-fixed"; + regulator-name = "VSD_3V3"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + gpio = <&gpio2 19 GPIO_ACTIVE_HIGH>; + enable-active-high; + startup-delay-us = <100>; + off-on-delay-us = <20000>; + }; + + reg_usb1_host_vbus: regulator-usb1-vbus { + compatible = "regulator-fixed"; + regulator-name = "usb1_host_vbus"; + regulator-max-microvolt = <5000000>; + regulator-min-microvolt = <5000000>; + gpio = <&pca6416_1 0 GPIO_ACTIVE_HIGH>; + enable-active-high; + }; +}; + +&ecspi2 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_ecspi2>; + cs-gpios = <&gpio5 13 GPIO_ACTIVE_LOW>; + status = "okay"; + + tpm: tpm@0 { + compatible = "infineon,slb9670"; + reg = <0>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_tpm>; + reset-gpios = <&gpio4 0 GPIO_ACTIVE_LOW>; + spi-max-frequency = <18500000>; + }; +}; + +&fec { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_fec>; + phy-mode = "rgmii-id"; + phy-handle = <ðphy1>; + fsl,magic-packet; + status = "okay"; + + mdio { + #address-cells = <1>; + #size-cells = <0>; + + ethphy1: ethernet-phy@3 { + compatible = "ethernet-phy-id0022.1640", + "ethernet-phy-ieee802.3-c22"; + reg = <3>; + reset-gpios = <&gpio4 18 GPIO_ACTIVE_LOW>; + reset-assert-us = <10000>; + reset-deassert-us = <150000>; + interrupt-parent = <&gpio4>; + interrupts = <2 IRQ_TYPE_LEVEL_LOW>; + }; + }; +}; + +&flexcan1 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_flexcan1>; + status = "okay"; +}; + +&gpio2 { + usb-mux-hog { + gpio-hog; + gpios = <20 0>; + output-low; + line-name = "USB-C Mux En"; + }; +}; + +&i2c2 { + clock-frequency = <384000>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_i2c2>; + status = "okay"; + + pca6416_3: gpio@20 { + compatible = "nxp,pcal6416"; + reg = <0x20>; + gpio-controller; + #gpio-cells = <2>; + interrupt-parent = <&gpio4>; + interrupts = <27 IRQ_TYPE_EDGE_FALLING>; + interrupt-controller; + #interrupt-cells = <2>; + }; +}; + +&i2c3 { + /* Connected to USB Hub */ + usb-typec@52 { + compatible = "nxp,ptn5110"; + reg = <0x52>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_typec>; + interrupt-parent = <&gpio4>; + interrupts = <1 IRQ_TYPE_LEVEL_LOW>; + + connector { + compatible = "usb-c-connector"; + label = "USB-C"; + power-role = "source"; + data-role = "host"; + source-pdos = <PDO_FIXED(5000, 3000, PDO_FIXED_USB_COMM)>; + }; + }; +}; + +&i2c4 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_i2c4>; + clock-frequency = <384000>; + status = "okay"; + + pca6416: gpio@20 { + compatible = "nxp,pcal6416"; + reg = <0x20>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_pcal6414>; + gpio-controller; + #gpio-cells = <2>; + interrupt-parent = <&gpio4>; + interrupts = <27 IRQ_TYPE_EDGE_FALLING>; + interrupt-controller; + #interrupt-cells = <2>; + }; + + pca6416_1: gpio@21 { + compatible = "nxp,pcal6416"; + reg = <0x21>; + gpio-controller; + #gpio-cells = <2>; + interrupt-parent = <&gpio4>; + interrupts = <27 IRQ_TYPE_EDGE_FALLING>; + interrupt-controller; + #interrupt-cells = <2>; + + usb-hub-hog { + gpio-hog; + gpios = <7 0>; + output-low; + line-name = "USB Hub Enable"; + }; + }; + + usb-typec@47 { + compatible = "ti,hd3ss3220"; + reg = <0x47>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_hd3ss3220>; + interrupt-parent = <&gpio4>; + interrupts = <19 IRQ_TYPE_LEVEL_LOW>; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + + hd3ss3220_in_ep: endpoint { + remote-endpoint = <&ss_ep>; + }; + }; + + port@1 { + reg = <1>; + + hd3ss3220_out_ep: endpoint { + remote-endpoint = <&usb3_role_switch>; + }; + }; + }; + }; +}; + +&pcie { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_pcie>; + reset-gpio = <&gpio4 21 GPIO_ACTIVE_LOW>; + status = "okay"; +}; + +&pcie_phy { + fsl,refclk-pad-mode = <IMX8_PCIE_REFCLK_PAD_INPUT>; + clocks = <&pcie0_refclk>; + clock-names = "ref"; + status = "okay"; +}; + +&snvs_pwrkey { + status = "okay"; +}; + +&uart2 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_uart2>; + status = "okay"; +}; + +&uart3 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_uart3>; + assigned-clocks = <&clk IMX8MP_CLK_UART3>; + assigned-clock-parents = <&clk IMX8MP_SYS_PLL1_80M>; + uart-has-rtscts; + status = "okay"; +}; + +&usb3_0 { + status = "okay"; +}; + +&usb_dwc3_0 { + dr_mode = "otg"; + hnp-disable; + srp-disable; + adp-disable; + usb-role-switch; + status = "okay"; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + usb3_hs_ep: endpoint { + remote-endpoint = <&hs_ep>; + }; + }; + port@1 { + reg = <1>; + usb3_role_switch: endpoint { + remote-endpoint = <&hd3ss3220_out_ep>; + }; + }; + }; +}; + +&usb3_phy0 { + vbus-supply = <®_usb1_host_vbus>; + status = "okay"; +}; + +&usb3_1 { + status = "okay"; +}; + +&usb_dwc3_1 { + dr_mode = "host"; + status = "okay"; +}; + +&usb3_phy1 { + status = "okay"; +}; + +&usdhc2 { + pinctrl-names = "default", "state_100mhz", "state_200mhz"; + pinctrl-0 = <&pinctrl_usdhc2>, <&pinctrl_usdhc2_gpio>; + pinctrl-1 = <&pinctrl_usdhc2_100mhz>, <&pinctrl_usdhc2_gpio>; + pinctrl-2 = <&pinctrl_usdhc2_200mhz>, <&pinctrl_usdhc2_gpio>; + cd-gpios = <&gpio2 12 GPIO_ACTIVE_LOW>; + vmmc-supply = <®_usdhc2_vmmc>; + bus-width = <4>; + status = "okay"; +}; + +&iomuxc { + pinctrl_ecspi2: ecspi2grp { + fsl,pins = < + MX8MP_IOMUXC_ECSPI2_SCLK__ECSPI2_SCLK 0x82 + MX8MP_IOMUXC_ECSPI2_MOSI__ECSPI2_MOSI 0x82 + MX8MP_IOMUXC_ECSPI2_MISO__ECSPI2_MISO 0x82 + MX8MP_IOMUXC_ECSPI2_SS0__GPIO5_IO13 0x40000 + >; + }; + + pinctrl_fec: fecgrp { + fsl,pins = < + MX8MP_IOMUXC_SAI1_RXD2__ENET1_MDC 0x2 + MX8MP_IOMUXC_SAI1_RXD3__ENET1_MDIO 0x2 + MX8MP_IOMUXC_SAI1_RXD4__ENET1_RGMII_RD0 0x90 + MX8MP_IOMUXC_SAI1_RXD5__ENET1_RGMII_RD1 0x90 + MX8MP_IOMUXC_SAI1_RXD6__ENET1_RGMII_RD2 0x90 + MX8MP_IOMUXC_SAI1_RXD7__ENET1_RGMII_RD3 0x90 + MX8MP_IOMUXC_SAI1_TXC__ENET1_RGMII_RXC 0x90 + MX8MP_IOMUXC_SAI1_TXFS__ENET1_RGMII_RX_CTL 0x90 + MX8MP_IOMUXC_SAI1_TXD0__ENET1_RGMII_TD0 0x16 + MX8MP_IOMUXC_SAI1_TXD1__ENET1_RGMII_TD1 0x16 + MX8MP_IOMUXC_SAI1_TXD2__ENET1_RGMII_TD2 0x16 + MX8MP_IOMUXC_SAI1_TXD3__ENET1_RGMII_TD3 0x16 + MX8MP_IOMUXC_SAI1_TXD4__ENET1_RGMII_TX_CTL 0x16 + MX8MP_IOMUXC_SAI1_TXD5__ENET1_RGMII_TXC 0x16 + MX8MP_IOMUXC_SAI1_RXD0__GPIO4_IO02 0x140 + MX8MP_IOMUXC_SAI1_TXD6__GPIO4_IO18 0x10 + >; + }; + + pinctrl_flexcan1: flexcan1grp { + fsl,pins = < + MX8MP_IOMUXC_SPDIF_RX__CAN1_RX 0x154 + MX8MP_IOMUXC_SPDIF_TX__CAN1_TX 0x154 + >; + }; + + pinctrl_hd3ss3220: hd3ss3220grp { + fsl,pins = < + MX8MP_IOMUXC_SAI1_TXD7__GPIO4_IO19 0x140 + >; + }; + + pinctrl_i2c2: i2c2grp { + fsl,pins = < + MX8MP_IOMUXC_I2C2_SCL__I2C2_SCL 0x400001c2 + MX8MP_IOMUXC_I2C2_SDA__I2C2_SDA 0x400001c2 + >; + }; + + pinctrl_i2c4: i2c4grp { + fsl,pins = < + MX8MP_IOMUXC_I2C4_SCL__I2C4_SCL 0x400001c2 + MX8MP_IOMUXC_I2C4_SDA__I2C4_SDA 0x400001c2 + >; + }; + + pinctrl_led3: led3grp { + fsl,pins = < + MX8MP_IOMUXC_SAI3_RXFS__GPIO4_IO28 0x41 + >; + }; + + pinctrl_pcal6414: pcal6414-gpiogrp { + fsl,pins = < + MX8MP_IOMUXC_SAI2_MCLK__GPIO4_IO27 0x10 + >; + }; + + pinctrl_pcie: pciegrp { + fsl,pins = < + MX8MP_IOMUXC_GPIO1_IO05__GPIO1_IO05 0x10 /* PCIe_nDIS */ + MX8MP_IOMUXC_SAI2_RXFS__GPIO4_IO21 0x10 /* PCIe_nRST */ + >; + }; + + pinctrl_reg_usdhc2_vmmc: regusdhc2vmmcgrp { + fsl,pins = < + MX8MP_IOMUXC_SD2_RESET_B__GPIO2_IO19 0x40 + >; + }; + + pinctrl_tpm: tpmgrp { + fsl,pins = < + MX8MP_IOMUXC_SAI1_RXFS__GPIO4_IO00 0x19 /* Reset */ + MX8MP_IOMUXC_SAI3_RXC__GPIO4_IO29 0x1d6 /* IRQ */ + >; + }; + + pinctrl_typec: typec1grp { + fsl,pins = < + MX8MP_IOMUXC_SAI1_RXC__GPIO4_IO01 0xc4 + >; + }; + + pinctrl_uart2: uart2grp { + fsl,pins = < + MX8MP_IOMUXC_UART2_RXD__UART2_DCE_RX 0x140 + MX8MP_IOMUXC_UART2_TXD__UART2_DCE_TX 0x140 + >; + }; + + pinctrl_uart3: uart3grp { + fsl,pins = < + MX8MP_IOMUXC_ECSPI1_SCLK__UART3_DCE_RX 0x140 + MX8MP_IOMUXC_ECSPI1_MOSI__UART3_DCE_TX 0x140 + MX8MP_IOMUXC_ECSPI1_SS0__UART3_DCE_RTS 0x140 + MX8MP_IOMUXC_ECSPI1_MISO__UART3_DCE_CTS 0x140 + >; + }; + + pinctrl_usdhc2: usdhc2grp { + fsl,pins = < + MX8MP_IOMUXC_SD2_CLK__USDHC2_CLK 0x190 + MX8MP_IOMUXC_SD2_CMD__USDHC2_CMD 0x1d0 + MX8MP_IOMUXC_SD2_DATA0__USDHC2_DATA0 0x1d0 + MX8MP_IOMUXC_SD2_DATA1__USDHC2_DATA1 0x1d0 + MX8MP_IOMUXC_SD2_DATA2__USDHC2_DATA2 0x1d0 + MX8MP_IOMUXC_SD2_DATA3__USDHC2_DATA3 0x1d0 + MX8MP_IOMUXC_GPIO1_IO04__USDHC2_VSELECT 0xc0 + >; + }; + + pinctrl_usdhc2_100mhz: usdhc2-100mhzgrp { + fsl,pins = < + MX8MP_IOMUXC_SD2_CLK__USDHC2_CLK 0x194 + MX8MP_IOMUXC_SD2_CMD__USDHC2_CMD 0x1d4 + MX8MP_IOMUXC_SD2_DATA0__USDHC2_DATA0 0x1d4 + MX8MP_IOMUXC_SD2_DATA1__USDHC2_DATA1 0x1d4 + MX8MP_IOMUXC_SD2_DATA2__USDHC2_DATA2 0x1d4 + MX8MP_IOMUXC_SD2_DATA3__USDHC2_DATA3 0x1d4 + MX8MP_IOMUXC_GPIO1_IO04__USDHC2_VSELECT 0xc0 + >; + }; + + pinctrl_usdhc2_200mhz: usdhc2-200mhzgrp { + fsl,pins = < + MX8MP_IOMUXC_SD2_CLK__USDHC2_CLK 0x196 + MX8MP_IOMUXC_SD2_CMD__USDHC2_CMD 0x1d6 + MX8MP_IOMUXC_SD2_DATA0__USDHC2_DATA0 0x1d6 + MX8MP_IOMUXC_SD2_DATA1__USDHC2_DATA1 0x1d6 + MX8MP_IOMUXC_SD2_DATA2__USDHC2_DATA2 0x1d6 + MX8MP_IOMUXC_SD2_DATA3__USDHC2_DATA3 0x1d6 + MX8MP_IOMUXC_GPIO1_IO04__USDHC2_VSELECT 0xc0 + >; + }; + + pinctrl_usdhc2_gpio: usdhc2gpiogrp { + fsl,pins = < + MX8MP_IOMUXC_SD2_CD_B__GPIO2_IO12 0x1c4 + >; + }; +}; diff --git a/arch/arm64/boot/dts/freescale/imx8mp-beacon-som.dtsi b/arch/arm64/boot/dts/freescale/imx8mp-beacon-som.dtsi new file mode 100644 index 000000000000..e5da90804780 --- /dev/null +++ b/arch/arm64/boot/dts/freescale/imx8mp-beacon-som.dtsi @@ -0,0 +1,416 @@ +// SPDX-License-Identifier: (GPL-2.0+ OR MIT) +/* + * Copyright 2023 LogicPD, Inc. dba Beacon EmbeddedWorks + */ + +/ { + aliases { + rtc0 = &rtc; + rtc1 = &snvs_rtc; + }; + + memory@40000000 { + device_type = "memory"; + reg = <0x0 0x40000000 0 0xc0000000>, + <0x1 0x00000000 0 0xc0000000>; + }; + + reg_wl_bt: regulator-wifi-bt { + compatible = "regulator-fixed"; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_reg_wl_bt>; + regulator-name = "wl-bt-pow-dwn"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + gpio = <&gpio2 6 GPIO_ACTIVE_LOW>; + startup-delay-us = <70000>; + regulator-always-on; + }; +}; + +&A53_0 { + cpu-supply = <&buck2>; +}; + +&A53_1 { + cpu-supply = <&buck2>; +}; + +&A53_2 { + cpu-supply = <&buck2>; +}; + +&A53_3 { + cpu-supply = <&buck2>; +}; + +&eqos { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_eqos>; + phy-mode = "rgmii-id"; + phy-handle = <ðphy0>; + snps,force_thresh_dma_mode; + status = "okay"; + + mdio { + compatible = "snps,dwmac-mdio"; + #address-cells = <1>; + #size-cells = <0>; + + ethphy0: ethernet-phy@3 { + compatible = "ethernet-phy-id0022.1640", + "ethernet-phy-ieee802.3-c22"; + reg = <3>; + reset-gpios = <&gpio4 10 GPIO_ACTIVE_LOW>; + interrupt-parent = <&gpio1>; + interrupts = <10 IRQ_TYPE_LEVEL_LOW>; + }; + }; +}; + +&flexspi { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_flexspi0>; + status = "okay"; + + flash0: flash@0 { + compatible = "jedec,spi-nor"; + reg = <0>; + spi-max-frequency = <80000000>; + spi-tx-bus-width = <1>; + spi-rx-bus-width = <4>; + }; +}; + +&i2c1 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_i2c1>; + clock-frequency = <384000>; + status = "okay"; + + pmic@25 { + compatible = "nxp,pca9450c"; + reg = <0x25>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_pmic>; + interrupt-parent = <&gpio1>; + interrupts = <3 IRQ_TYPE_LEVEL_LOW>; + + regulators { + buck1: BUCK1 { + regulator-name = "BUCK1"; + regulator-min-microvolt = <600000>; + regulator-max-microvolt = <2187500>; + regulator-boot-on; + regulator-always-on; + regulator-ramp-delay = <3125>; + }; + + buck2: BUCK2 { + regulator-name = "BUCK2"; + regulator-min-microvolt = <600000>; + regulator-max-microvolt = <2187500>; + regulator-boot-on; + regulator-always-on; + regulator-ramp-delay = <3125>; + nxp,dvs-run-voltage = <950000>; + nxp,dvs-standby-voltage = <850000>; + }; + + buck4: BUCK4 { + regulator-name = "BUCK4"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-boot-on; + regulator-always-on; + }; + + buck5: BUCK5 { + regulator-name = "BUCK5"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-boot-on; + regulator-always-on; + }; + + buck6: BUCK6 { + regulator-name = "BUCK6"; + regulator-min-microvolt = <600000>; + regulator-max-microvolt = <3400000>; + regulator-boot-on; + regulator-always-on; + }; + + ldo1: LDO1 { + regulator-name = "LDO1"; + regulator-min-microvolt = <1600000>; + regulator-max-microvolt = <1800000>; + regulator-boot-on; + regulator-always-on; + }; + + ldo3: LDO3 { + regulator-name = "LDO3"; + regulator-min-microvolt = <800000>; + regulator-max-microvolt = <1800000>; + regulator-boot-on; + regulator-always-on; + }; + + ldo4: LDO4 { + regulator-name = "LDO4"; + regulator-min-microvolt = <800000>; + regulator-max-microvolt = <3300000>; + regulator-boot-on; + regulator-always-on; + }; + + ldo5: LDO5 { + regulator-name = "LDO5"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <3300000>; + regulator-boot-on; + regulator-always-on; + }; + }; + }; +}; + +&i2c3 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_i2c3>; + clock-frequency = <384000>; + status = "okay"; + + eeprom@50 { + compatible = "atmel,24c64"; + reg = <0x50>; + pagesize = <32>; + read-only; /* Manufacturing EEPROM programmed at factory */ + }; + + rtc: rtc@51 { + compatible = "nxp,pcf85263"; + reg = <0x51>; + }; +}; + +&snvs_pwrkey { + status = "okay"; +}; + +&uart1 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_uart1>; + assigned-clocks = <&clk IMX8MP_CLK_UART1>; + assigned-clock-parents = <&clk IMX8MP_SYS_PLL1_80M>; + uart-has-rtscts; + status = "okay"; +}; + +&usdhc1 { + pinctrl-names = "default", "state_100mhz", "state_200mhz"; + pinctrl-0 = <&pinctrl_usdhc1>; + pinctrl-1 = <&pinctrl_usdhc1_100mhz>; + pinctrl-2 = <&pinctrl_usdhc1_200mhz>; + bus-width = <4>; + vmmc-supply = <®_wl_bt>; + cap-sd-highspeed; + sd-uhs-sdr50; + sd-uhs-sdr104; + keep-power-in-suspend; + wakeup-source; + non-removable; + cap-power-off-card; + #address-cells = <1>; + #size-cells = <0>; + status = "okay"; + + mwifiex: wifi@1 { + compatible = "marvell,sd8997"; + reg = <1>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_wlan>; + interrupt-parent = <&gpio2>; + interrupts = <9 IRQ_TYPE_LEVEL_LOW>; + }; +}; + +&usdhc3 { + pinctrl-names = "default", "state_100mhz", "state_200mhz"; + pinctrl-0 = <&pinctrl_usdhc3>; + pinctrl-1 = <&pinctrl_usdhc3_100mhz>; + pinctrl-2 = <&pinctrl_usdhc3_200mhz>; + bus-width = <8>; + non-removable; + status = "okay"; +}; + +&wdog1 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_wdog>; + fsl,ext-reset-output; + status = "okay"; +}; + +&iomuxc { + pinctrl_eqos: eqosgrp { + fsl,pins = < + MX8MP_IOMUXC_ENET_MDC__ENET_QOS_MDC 0x2 + MX8MP_IOMUXC_ENET_MDIO__ENET_QOS_MDIO 0x2 + MX8MP_IOMUXC_ENET_RD0__ENET_QOS_RGMII_RD0 0x90 + MX8MP_IOMUXC_ENET_RD1__ENET_QOS_RGMII_RD1 0x90 + MX8MP_IOMUXC_ENET_RD2__ENET_QOS_RGMII_RD2 0x90 + MX8MP_IOMUXC_ENET_RD3__ENET_QOS_RGMII_RD3 0x90 + MX8MP_IOMUXC_ENET_RXC__CCM_ENET_QOS_CLOCK_GENERATE_RX_CLK 0x90 + MX8MP_IOMUXC_ENET_RX_CTL__ENET_QOS_RGMII_RX_CTL 0x90 + MX8MP_IOMUXC_ENET_TD0__ENET_QOS_RGMII_TD0 0x16 + MX8MP_IOMUXC_ENET_TD1__ENET_QOS_RGMII_TD1 0x16 + MX8MP_IOMUXC_ENET_TD2__ENET_QOS_RGMII_TD2 0x16 + MX8MP_IOMUXC_ENET_TD3__ENET_QOS_RGMII_TD3 0x16 + MX8MP_IOMUXC_ENET_TX_CTL__ENET_QOS_RGMII_TX_CTL 0x16 + MX8MP_IOMUXC_ENET_TXC__CCM_ENET_QOS_CLOCK_GENERATE_TX_CLK 0x16 + MX8MP_IOMUXC_SAI2_RXC__GPIO4_IO22 0x10 + MX8MP_IOMUXC_GPIO1_IO10__GPIO1_IO10 0x10 + >; + }; + + pinctrl_flexspi0: flexspi0grp { + fsl,pins = < + MX8MP_IOMUXC_NAND_ALE__FLEXSPI_A_SCLK 0x1c2 + MX8MP_IOMUXC_NAND_CE0_B__FLEXSPI_A_SS0_B 0x82 + MX8MP_IOMUXC_NAND_DATA00__FLEXSPI_A_DATA00 0x82 + MX8MP_IOMUXC_NAND_DATA01__FLEXSPI_A_DATA01 0x82 + MX8MP_IOMUXC_NAND_DATA02__FLEXSPI_A_DATA02 0x82 + MX8MP_IOMUXC_NAND_DATA03__FLEXSPI_A_DATA03 0x82 + >; + }; + + pinctrl_i2c1: i2c1grp { + fsl,pins = < + MX8MP_IOMUXC_I2C1_SCL__I2C1_SCL 0x400001c2 + MX8MP_IOMUXC_I2C1_SDA__I2C1_SDA 0x400001c2 + >; + }; + + pinctrl_i2c3: i2c3grp { + fsl,pins = < + MX8MP_IOMUXC_I2C3_SCL__I2C3_SCL 0x400001c2 + MX8MP_IOMUXC_I2C3_SDA__I2C3_SDA 0x400001c2 + >; + }; + + pinctrl_pmic: pmicgrp { + fsl,pins = < + MX8MP_IOMUXC_GPIO1_IO03__GPIO1_IO03 0x1c0 + >; + }; + + pinctrl_reg_wl_bt: reg-wl-btgrp { + fsl,pins = < + MX8MP_IOMUXC_SD1_DATA4__GPIO2_IO06 0x40 + >; + }; + + pinctrl_uart1: uart1grp { + fsl,pins = < + MX8MP_IOMUXC_UART1_RXD__UART1_DCE_RX 0x140 + MX8MP_IOMUXC_UART1_TXD__UART1_DCE_TX 0x140 + MX8MP_IOMUXC_UART3_RXD__UART1_DCE_CTS 0x140 + MX8MP_IOMUXC_UART3_TXD__UART1_DCE_RTS 0x140 + >; + }; + + pinctrl_usdhc1: usdhc1grp { + fsl,pins = < + MX8MP_IOMUXC_SD1_CLK__USDHC1_CLK 0x190 + MX8MP_IOMUXC_SD1_CMD__USDHC1_CMD 0x1d0 + MX8MP_IOMUXC_SD1_DATA0__USDHC1_DATA0 0x1d0 + MX8MP_IOMUXC_SD1_DATA1__USDHC1_DATA1 0x1d0 + MX8MP_IOMUXC_SD1_DATA2__USDHC1_DATA2 0x1d0 + MX8MP_IOMUXC_SD1_DATA3__USDHC1_DATA3 0x1d0 + >; + }; + + pinctrl_usdhc1_100mhz: usdhc1-100mhzgrp { + fsl,pins = < + MX8MP_IOMUXC_SD1_CLK__USDHC1_CLK 0x194 + MX8MP_IOMUXC_SD1_CMD__USDHC1_CMD 0x1d4 + MX8MP_IOMUXC_SD1_DATA0__USDHC1_DATA0 0x1d4 + MX8MP_IOMUXC_SD1_DATA1__USDHC1_DATA1 0x1d4 + MX8MP_IOMUXC_SD1_DATA2__USDHC1_DATA2 0x1d4 + MX8MP_IOMUXC_SD1_DATA3__USDHC1_DATA3 0x1d4 + >; + }; + + pinctrl_usdhc1_200mhz: usdhc1-200mhzgrp { + fsl,pins = < + MX8MP_IOMUXC_SD1_CLK__USDHC1_CLK 0x196 + MX8MP_IOMUXC_SD1_CMD__USDHC1_CMD 0x1d6 + MX8MP_IOMUXC_SD1_DATA0__USDHC1_DATA0 0x1d6 + MX8MP_IOMUXC_SD1_DATA1__USDHC1_DATA1 0x1d6 + MX8MP_IOMUXC_SD1_DATA2__USDHC1_DATA2 0x1d6 + MX8MP_IOMUXC_SD1_DATA3__USDHC1_DATA3 0x1d6 + >; + }; + + pinctrl_usdhc3: usdhc3grp { + fsl,pins = < + MX8MP_IOMUXC_NAND_WE_B__USDHC3_CLK 0x190 + MX8MP_IOMUXC_NAND_WP_B__USDHC3_CMD 0x1d0 + MX8MP_IOMUXC_NAND_DATA04__USDHC3_DATA0 0x1d0 + MX8MP_IOMUXC_NAND_DATA05__USDHC3_DATA1 0x1d0 + MX8MP_IOMUXC_NAND_DATA06__USDHC3_DATA2 0x1d0 + MX8MP_IOMUXC_NAND_DATA07__USDHC3_DATA3 0x1d0 + MX8MP_IOMUXC_NAND_RE_B__USDHC3_DATA4 0x1d0 + MX8MP_IOMUXC_NAND_CE2_B__USDHC3_DATA5 0x1d0 + MX8MP_IOMUXC_NAND_CE3_B__USDHC3_DATA6 0x1d0 + MX8MP_IOMUXC_NAND_CLE__USDHC3_DATA7 0x1d0 + MX8MP_IOMUXC_NAND_CE1_B__USDHC3_STROBE 0x190 + >; + }; + + pinctrl_usdhc3_100mhz: usdhc3-100mhzgrp { + fsl,pins = < + MX8MP_IOMUXC_NAND_WE_B__USDHC3_CLK 0x194 + MX8MP_IOMUXC_NAND_WP_B__USDHC3_CMD 0x1d4 + MX8MP_IOMUXC_NAND_DATA04__USDHC3_DATA0 0x1d4 + MX8MP_IOMUXC_NAND_DATA05__USDHC3_DATA1 0x1d4 + MX8MP_IOMUXC_NAND_DATA06__USDHC3_DATA2 0x1d4 + MX8MP_IOMUXC_NAND_DATA07__USDHC3_DATA3 0x1d4 + MX8MP_IOMUXC_NAND_RE_B__USDHC3_DATA4 0x1d4 + MX8MP_IOMUXC_NAND_CE2_B__USDHC3_DATA5 0x1d4 + MX8MP_IOMUXC_NAND_CE3_B__USDHC3_DATA6 0x1d4 + MX8MP_IOMUXC_NAND_CLE__USDHC3_DATA7 0x1d4 + MX8MP_IOMUXC_NAND_CE1_B__USDHC3_STROBE 0x194 + >; + }; + + pinctrl_usdhc3_200mhz: usdhc3-200mhzgrp { + fsl,pins = < + MX8MP_IOMUXC_NAND_WE_B__USDHC3_CLK 0x196 + MX8MP_IOMUXC_NAND_WP_B__USDHC3_CMD 0x1d6 + MX8MP_IOMUXC_NAND_DATA04__USDHC3_DATA0 0x1d6 + MX8MP_IOMUXC_NAND_DATA05__USDHC3_DATA1 0x1d6 + MX8MP_IOMUXC_NAND_DATA06__USDHC3_DATA2 0x1d6 + MX8MP_IOMUXC_NAND_DATA07__USDHC3_DATA3 0x1d6 + MX8MP_IOMUXC_NAND_RE_B__USDHC3_DATA4 0x1d6 + MX8MP_IOMUXC_NAND_CE2_B__USDHC3_DATA5 0x1d6 + MX8MP_IOMUXC_NAND_CE3_B__USDHC3_DATA6 0x1d6 + MX8MP_IOMUXC_NAND_CLE__USDHC3_DATA7 0x1d6 + MX8MP_IOMUXC_NAND_CE1_B__USDHC3_STROBE 0x196 + >; + }; + + pinctrl_wdog: wdoggrp { + fsl,pins = < + MX8MP_IOMUXC_GPIO1_IO02__WDOG1_WDOG_B 0x166 + >; + }; + + pinctrl_wlan: wlangrp { + fsl,pins = < + MX8MP_IOMUXC_SD1_DATA7__GPIO2_IO09 0x140 + >; + }; +}; diff --git a/arch/arm64/boot/dts/freescale/imx8mp-debix-model-a.dts b/arch/arm64/boot/dts/freescale/imx8mp-debix-model-a.dts new file mode 100644 index 000000000000..2876d18f2a38 --- /dev/null +++ b/arch/arm64/boot/dts/freescale/imx8mp-debix-model-a.dts @@ -0,0 +1,506 @@ +// SPDX-License-Identifier: (GPL-2.0+ OR MIT) +/* + * Copyright 2019 NXP + * Copyright 2022 Ideas on Board Oy + */ + +/dts-v1/; + +#include <dt-bindings/gpio/gpio.h> +#include <dt-bindings/leds/common.h> +#include <dt-bindings/usb/pd.h> + +#include "imx8mp.dtsi" + +/ { + model = "Polyhex Debix Model A i.MX8MPlus board"; + compatible = "polyhex,imx8mp-debix-model-a", "polyhex,imx8mp-debix", "fsl,imx8mp"; + + chosen { + stdout-path = &uart2; + }; + + leds { + compatible = "gpio-leds"; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_gpio_led>; + + led-0 { + function = LED_FUNCTION_POWER; + color = <LED_COLOR_ID_RED>; + gpios = <&gpio3 16 GPIO_ACTIVE_HIGH>; + default-state = "on"; + }; + }; + + reg_usdhc2_vmmc: regulator-usdhc2 { + compatible = "regulator-fixed"; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_reg_usdhc2_vmmc>; + regulator-name = "VSD_3V3"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + gpio = <&gpio2 19 GPIO_ACTIVE_HIGH>; + enable-active-high; + }; +}; + +&A53_0 { + cpu-supply = <&buck2>; +}; + +&A53_1 { + cpu-supply = <&buck2>; +}; + +&A53_2 { + cpu-supply = <&buck2>; +}; + +&A53_3 { + cpu-supply = <&buck2>; +}; + +&eqos { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_eqos>; + phy-connection-type = "rgmii-id"; + phy-handle = <ðphy0>; + status = "okay"; + + mdio { + compatible = "snps,dwmac-mdio"; + #address-cells = <1>; + #size-cells = <0>; + + ethphy0: ethernet-phy@0 { /* RTL8211E */ + compatible = "ethernet-phy-ieee802.3-c22"; + reg = <0>; + reset-gpios = <&gpio4 18 GPIO_ACTIVE_LOW>; + reset-assert-us = <20>; + reset-deassert-us = <200000>; + }; + }; +}; + +&i2c1 { + clock-frequency = <400000>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_i2c1>; + status = "okay"; + + pmic@25 { + compatible = "nxp,pca9450c"; + reg = <0x25>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_pmic>; + interrupt-parent = <&gpio1>; + interrupts = <3 IRQ_TYPE_EDGE_RISING>; + + regulators { + buck1: BUCK1 { + regulator-name = "BUCK1"; + regulator-min-microvolt = <600000>; + regulator-max-microvolt = <2187500>; + regulator-boot-on; + regulator-always-on; + regulator-ramp-delay = <3125>; + }; + + buck2: BUCK2 { + regulator-name = "BUCK2"; + regulator-min-microvolt = <600000>; + regulator-max-microvolt = <2187500>; + regulator-boot-on; + regulator-always-on; + regulator-ramp-delay = <3125>; + nxp,dvs-run-voltage = <950000>; + nxp,dvs-standby-voltage = <850000>; + }; + + buck4: BUCK4{ + regulator-name = "BUCK4"; + regulator-min-microvolt = <600000>; + regulator-max-microvolt = <3400000>; + regulator-boot-on; + regulator-always-on; + }; + + buck5: BUCK5{ + regulator-name = "BUCK5"; + regulator-min-microvolt = <600000>; + regulator-max-microvolt = <3400000>; + regulator-boot-on; + regulator-always-on; + }; + + buck6: BUCK6 { + regulator-name = "BUCK6"; + regulator-min-microvolt = <600000>; + regulator-max-microvolt = <3400000>; + regulator-boot-on; + regulator-always-on; + }; + + ldo1: LDO1 { + regulator-name = "LDO1"; + regulator-min-microvolt = <1600000>; + regulator-max-microvolt = <3300000>; + regulator-boot-on; + regulator-always-on; + }; + + ldo2: LDO2 { + regulator-name = "LDO2"; + regulator-min-microvolt = <800000>; + regulator-max-microvolt = <1150000>; + regulator-boot-on; + regulator-always-on; + }; + + ldo3: LDO3 { + regulator-name = "LDO3"; + regulator-min-microvolt = <800000>; + regulator-max-microvolt = <3300000>; + regulator-boot-on; + regulator-always-on; + }; + + ldo4: LDO4 { + regulator-name = "LDO4"; + regulator-min-microvolt = <800000>; + regulator-max-microvolt = <3300000>; + regulator-boot-on; + regulator-always-on; + }; + + ldo5: LDO5 { + regulator-name = "LDO5"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <3300000>; + regulator-boot-on; + regulator-always-on; + }; + }; + }; +}; + +&i2c2 { + clock-frequency = <100000>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_i2c2>; + status = "okay"; +}; + +&i2c3 { + clock-frequency = <400000>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_i2c3>; + status = "okay"; +}; + +&i2c4 { + clock-frequency = <100000>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_i2c4>; + status = "okay"; + + eeprom@50 { + compatible = "atmel,24c02"; + reg = <0x50>; + pagesize = <16>; + }; + + rtc@51 { + compatible = "haoyu,hym8563"; + reg = <0x51>; + #clock-cells = <0>; + clock-frequency = <32768>; + clock-output-names = "xin32k"; + interrupt-parent = <&gpio2>; + interrupts = <11 IRQ_TYPE_EDGE_FALLING>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_rtc_int>; + }; +}; + +&i2c6 { + clock-frequency = <400000>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_i2c6>; + status = "okay"; +}; + +&snvs_pwrkey { + status = "okay"; +}; + +&uart2 { + /* console */ + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_uart2>; + status = "okay"; +}; + +&uart3 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_uart3>; + status = "okay"; +}; + +&uart4 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_uart4>; + status = "okay"; +}; + +/* SD Card */ +&usdhc2 { + pinctrl-names = "default", "state_100mhz", "state_200mhz"; + pinctrl-0 = <&pinctrl_usdhc2>, <&pinctrl_usdhc2_gpio>; + pinctrl-1 = <&pinctrl_usdhc2_100mhz>, <&pinctrl_usdhc2_gpio>; + pinctrl-2 = <&pinctrl_usdhc2_200mhz>, <&pinctrl_usdhc2_gpio>; + cd-gpios = <&gpio2 12 GPIO_ACTIVE_LOW>; + vmmc-supply = <®_usdhc2_vmmc>; + bus-width = <4>; + status = "okay"; +}; + +/* eMMC */ +&usdhc3 { + assigned-clocks = <&clk IMX8MP_CLK_USDHC3>; + assigned-clock-rates = <400000000>; + pinctrl-names = "default", "state_100mhz", "state_200mhz"; + pinctrl-0 = <&pinctrl_usdhc3>; + pinctrl-1 = <&pinctrl_usdhc3_100mhz>; + pinctrl-2 = <&pinctrl_usdhc3_200mhz>; + bus-width = <8>; + non-removable; + status = "okay"; +}; + +&wdog1 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_wdog>; + fsl,ext-reset-output; + status = "okay"; +}; + +&iomuxc { + pinctrl_eqos: eqosgrp { + fsl,pins = < + MX8MP_IOMUXC_ENET_MDC__ENET_QOS_MDC 0x3 + MX8MP_IOMUXC_ENET_MDIO__ENET_QOS_MDIO 0x3 + MX8MP_IOMUXC_ENET_RD0__ENET_QOS_RGMII_RD0 0x91 + MX8MP_IOMUXC_ENET_RD1__ENET_QOS_RGMII_RD1 0x91 + MX8MP_IOMUXC_ENET_RD2__ENET_QOS_RGMII_RD2 0x91 + MX8MP_IOMUXC_ENET_RD3__ENET_QOS_RGMII_RD3 0x91 + MX8MP_IOMUXC_ENET_RXC__CCM_ENET_QOS_CLOCK_GENERATE_RX_CLK 0x91 + MX8MP_IOMUXC_ENET_RX_CTL__ENET_QOS_RGMII_RX_CTL 0x91 + MX8MP_IOMUXC_ENET_TD0__ENET_QOS_RGMII_TD0 0x1f + MX8MP_IOMUXC_ENET_TD1__ENET_QOS_RGMII_TD1 0x1f + MX8MP_IOMUXC_ENET_TD2__ENET_QOS_RGMII_TD2 0x1f + MX8MP_IOMUXC_ENET_TD3__ENET_QOS_RGMII_TD3 0x1f + MX8MP_IOMUXC_ENET_TX_CTL__ENET_QOS_RGMII_TX_CTL 0x1f + MX8MP_IOMUXC_ENET_TXC__CCM_ENET_QOS_CLOCK_GENERATE_TX_CLK 0x1f + MX8MP_IOMUXC_SAI1_RXFS__ENET1_1588_EVENT0_IN 0x1f + MX8MP_IOMUXC_SAI1_RXC__ENET1_1588_EVENT0_OUT 0x1f + MX8MP_IOMUXC_SAI1_TXD6__GPIO4_IO18 0x19 + >; + }; + + pinctrl_fec: fecgrp { + fsl,pins = < + MX8MP_IOMUXC_SAI1_RXD2__ENET1_MDC 0x3 + MX8MP_IOMUXC_SAI1_RXD3__ENET1_MDIO 0x3 + MX8MP_IOMUXC_SAI1_RXD4__ENET1_RGMII_RD0 0x91 + MX8MP_IOMUXC_SAI1_RXD5__ENET1_RGMII_RD1 0x91 + MX8MP_IOMUXC_SAI1_RXD6__ENET1_RGMII_RD2 0x91 + MX8MP_IOMUXC_SAI1_RXD7__ENET1_RGMII_RD3 0x91 + MX8MP_IOMUXC_SAI1_TXC__ENET1_RGMII_RXC 0x91 + MX8MP_IOMUXC_SAI1_TXFS__ENET1_RGMII_RX_CTL 0x91 + MX8MP_IOMUXC_SAI1_TXD0__ENET1_RGMII_TD0 0x1f + MX8MP_IOMUXC_SAI1_TXD1__ENET1_RGMII_TD1 0x1f + MX8MP_IOMUXC_SAI1_TXD2__ENET1_RGMII_TD2 0x1f + MX8MP_IOMUXC_SAI1_TXD3__ENET1_RGMII_TD3 0x1f + MX8MP_IOMUXC_SAI1_TXD4__ENET1_RGMII_TX_CTL 0x1f + MX8MP_IOMUXC_SAI1_TXD5__ENET1_RGMII_TXC 0x1f + MX8MP_IOMUXC_SAI1_RXD1__ENET1_1588_EVENT1_OUT 0x1f + MX8MP_IOMUXC_SAI1_RXD0__ENET1_1588_EVENT1_IN 0x1f + MX8MP_IOMUXC_SAI1_TXD7__GPIO4_IO19 0x19 + >; + }; + + pinctrl_gpio_led: gpioledgrp { + fsl,pins = < + MX8MP_IOMUXC_NAND_READY_B__GPIO3_IO16 0x19 + >; + }; + + pinctrl_i2c1: i2c1grp { + fsl,pins = < + MX8MP_IOMUXC_I2C1_SCL__I2C1_SCL 0x400001c2 + MX8MP_IOMUXC_I2C1_SDA__I2C1_SDA 0x400001c2 + >; + }; + + pinctrl_i2c2: i2c2grp { + fsl,pins = < + MX8MP_IOMUXC_I2C2_SCL__I2C2_SCL 0x400001c2 + MX8MP_IOMUXC_I2C2_SDA__I2C2_SDA 0x400001c2 + >; + }; + + pinctrl_i2c3: i2c3grp { + fsl,pins = < + MX8MP_IOMUXC_I2C3_SCL__I2C3_SCL 0x400001c2 + MX8MP_IOMUXC_I2C3_SDA__I2C3_SDA 0x400001c2 + >; + }; + + pinctrl_i2c4: i2c4grp { + fsl,pins = < + MX8MP_IOMUXC_I2C4_SCL__I2C4_SCL 0x400001c3 + MX8MP_IOMUXC_I2C4_SDA__I2C4_SDA 0x400001c3 + >; + }; + + pinctrl_i2c6: i2c6grp { + fsl,pins = < + MX8MP_IOMUXC_SAI5_RXFS__I2C6_SCL 0x400001c3 + MX8MP_IOMUXC_SAI5_RXC__I2C6_SDA 0x400001c3 + >; + }; + + pinctrl_pmic: pmicirqgrp { + fsl,pins = < + MX8MP_IOMUXC_GPIO1_IO03__GPIO1_IO03 0x41 + >; + }; + + pinctrl_reg_usdhc2_vmmc: regusdhc2vmmcgrp { + fsl,pins = < + MX8MP_IOMUXC_SD2_RESET_B__GPIO2_IO19 0x41 + >; + }; + + pinctrl_rtc_int: rtcintgrp { + fsl,pins = < + MX8MP_IOMUXC_SD1_STROBE__GPIO2_IO11 0x140 + >; + }; + + pinctrl_uart2: uart2grp { + fsl,pins = < + MX8MP_IOMUXC_UART2_RXD__UART2_DCE_RX 0x14f + MX8MP_IOMUXC_UART2_TXD__UART2_DCE_TX 0x14f + >; + }; + + pinctrl_uart3: uart3grp { + fsl,pins = < + MX8MP_IOMUXC_UART3_RXD__UART3_DCE_RX 0x49 + MX8MP_IOMUXC_UART3_TXD__UART3_DCE_TX 0x49 + >; + }; + + pinctrl_uart4: uart4grp { + fsl,pins = < + MX8MP_IOMUXC_UART4_RXD__UART4_DCE_RX 0x49 + MX8MP_IOMUXC_UART4_TXD__UART4_DCE_TX 0x49 + >; + }; + + pinctrl_usdhc2: usdhc2grp { + fsl,pins = < + MX8MP_IOMUXC_SD2_CLK__USDHC2_CLK 0x190 + MX8MP_IOMUXC_SD2_CMD__USDHC2_CMD 0x1d0 + MX8MP_IOMUXC_SD2_DATA0__USDHC2_DATA0 0x1d0 + MX8MP_IOMUXC_SD2_DATA1__USDHC2_DATA1 0x1d0 + MX8MP_IOMUXC_SD2_DATA2__USDHC2_DATA2 0x1d0 + MX8MP_IOMUXC_SD2_DATA3__USDHC2_DATA3 0x1d0 + >; + }; + + pinctrl_usdhc2_100mhz: usdhc2-100mhzgrp { + fsl,pins = < + MX8MP_IOMUXC_SD2_CLK__USDHC2_CLK 0x194 + MX8MP_IOMUXC_SD2_CMD__USDHC2_CMD 0x1d4 + MX8MP_IOMUXC_SD2_DATA0__USDHC2_DATA0 0x1d4 + MX8MP_IOMUXC_SD2_DATA1__USDHC2_DATA1 0x1d4 + MX8MP_IOMUXC_SD2_DATA2__USDHC2_DATA2 0x1d4 + MX8MP_IOMUXC_SD2_DATA3__USDHC2_DATA3 0x1d4 + >; + }; + + pinctrl_usdhc2_200mhz: usdhc2-200mhzgrp { + fsl,pins = < + MX8MP_IOMUXC_SD2_CLK__USDHC2_CLK 0x196 + MX8MP_IOMUXC_SD2_CMD__USDHC2_CMD 0x1d6 + MX8MP_IOMUXC_SD2_DATA0__USDHC2_DATA0 0x1d6 + MX8MP_IOMUXC_SD2_DATA1__USDHC2_DATA1 0x1d6 + MX8MP_IOMUXC_SD2_DATA2__USDHC2_DATA2 0x1d6 + MX8MP_IOMUXC_SD2_DATA3__USDHC2_DATA3 0x1d6 + >; + }; + + pinctrl_usdhc2_gpio: usdhc2gpiogrp { + fsl,pins = < + MX8MP_IOMUXC_SD2_CD_B__GPIO2_IO12 0x1c4 + >; + }; + + pinctrl_usdhc3: usdhc3grp { + fsl,pins = < + MX8MP_IOMUXC_NAND_WE_B__USDHC3_CLK 0x190 + MX8MP_IOMUXC_NAND_WP_B__USDHC3_CMD 0x1d0 + MX8MP_IOMUXC_NAND_DATA04__USDHC3_DATA0 0x1d0 + MX8MP_IOMUXC_NAND_DATA05__USDHC3_DATA1 0x1d0 + MX8MP_IOMUXC_NAND_DATA06__USDHC3_DATA2 0x1d0 + MX8MP_IOMUXC_NAND_DATA07__USDHC3_DATA3 0x1d0 + MX8MP_IOMUXC_NAND_RE_B__USDHC3_DATA4 0x1d0 + MX8MP_IOMUXC_NAND_CE2_B__USDHC3_DATA5 0x1d0 + MX8MP_IOMUXC_NAND_CE3_B__USDHC3_DATA6 0x1d0 + MX8MP_IOMUXC_NAND_CLE__USDHC3_DATA7 0x1d0 + MX8MP_IOMUXC_NAND_CE1_B__USDHC3_STROBE 0x190 + >; + }; + + pinctrl_usdhc3_100mhz: usdhc3-100mhzgrp { + fsl,pins = < + MX8MP_IOMUXC_NAND_WE_B__USDHC3_CLK 0x194 + MX8MP_IOMUXC_NAND_WP_B__USDHC3_CMD 0x1d4 + MX8MP_IOMUXC_NAND_DATA04__USDHC3_DATA0 0x1d4 + MX8MP_IOMUXC_NAND_DATA05__USDHC3_DATA1 0x1d4 + MX8MP_IOMUXC_NAND_DATA06__USDHC3_DATA2 0x1d4 + MX8MP_IOMUXC_NAND_DATA07__USDHC3_DATA3 0x1d4 + MX8MP_IOMUXC_NAND_RE_B__USDHC3_DATA4 0x1d4 + MX8MP_IOMUXC_NAND_CE2_B__USDHC3_DATA5 0x1d4 + MX8MP_IOMUXC_NAND_CE3_B__USDHC3_DATA6 0x1d4 + MX8MP_IOMUXC_NAND_CLE__USDHC3_DATA7 0x1d4 + MX8MP_IOMUXC_NAND_CE1_B__USDHC3_STROBE 0x194 + >; + }; + + pinctrl_usdhc3_200mhz: usdhc3-200mhzgrp { + fsl,pins = < + MX8MP_IOMUXC_NAND_WE_B__USDHC3_CLK 0x196 + MX8MP_IOMUXC_NAND_WP_B__USDHC3_CMD 0x1d6 + MX8MP_IOMUXC_NAND_DATA04__USDHC3_DATA0 0x1d6 + MX8MP_IOMUXC_NAND_DATA05__USDHC3_DATA1 0x1d6 + MX8MP_IOMUXC_NAND_DATA06__USDHC3_DATA2 0x1d6 + MX8MP_IOMUXC_NAND_DATA07__USDHC3_DATA3 0x1d6 + MX8MP_IOMUXC_NAND_RE_B__USDHC3_DATA4 0x1d6 + MX8MP_IOMUXC_NAND_CE2_B__USDHC3_DATA5 0x1d6 + MX8MP_IOMUXC_NAND_CE3_B__USDHC3_DATA6 0x1d6 + MX8MP_IOMUXC_NAND_CLE__USDHC3_DATA7 0x1d6 + MX8MP_IOMUXC_NAND_CE1_B__USDHC3_STROBE 0x196 + >; + }; + + pinctrl_wdog: wdoggrp { + fsl,pins = < + MX8MP_IOMUXC_GPIO1_IO02__WDOG1_WDOG_B 0xc6 + >; + }; +}; diff --git a/arch/arm64/boot/dts/freescale/imx8mp-dhcom-som.dtsi b/arch/arm64/boot/dts/freescale/imx8mp-dhcom-som.dtsi index 6e1192e751f8..9cdd4234c4ca 100644 --- a/arch/arm64/boot/dts/freescale/imx8mp-dhcom-som.dtsi +++ b/arch/arm64/boot/dts/freescale/imx8mp-dhcom-som.dtsi @@ -239,7 +239,6 @@ pinctrl-0 = <&pinctrl_pmic>; interrupt-parent = <&gpio1>; interrupts = <3 IRQ_TYPE_LEVEL_LOW>; - sd-vsel-gpios = <&gpio1 4 GPIO_ACTIVE_HIGH>; /* * i.MX 8M Plus Data Sheet for Consumer Products @@ -248,7 +247,6 @@ */ regulators { buck1: BUCK1 { /* VDD_SOC (dual-phase with BUCK3) */ - regulator-compatible = "BUCK1"; regulator-min-microvolt = <850000>; regulator-max-microvolt = <1000000>; regulator-ramp-delay = <3125>; @@ -257,7 +255,6 @@ }; buck2: BUCK2 { /* VDD_ARM */ - regulator-compatible = "BUCK2"; regulator-min-microvolt = <850000>; regulator-max-microvolt = <1000000>; regulator-ramp-delay = <3125>; @@ -266,7 +263,6 @@ }; buck4: BUCK4 { /* VDD_3V3 */ - regulator-compatible = "BUCK4"; regulator-min-microvolt = <3300000>; regulator-max-microvolt = <3300000>; regulator-always-on; @@ -274,7 +270,6 @@ }; buck5: BUCK5 { /* VDD_1V8 */ - regulator-compatible = "BUCK5"; regulator-min-microvolt = <1800000>; regulator-max-microvolt = <1800000>; regulator-always-on; @@ -282,7 +277,6 @@ }; buck6: BUCK6 { /* NVCC_DRAM_1V1 */ - regulator-compatible = "BUCK6"; regulator-min-microvolt = <1100000>; regulator-max-microvolt = <1100000>; regulator-always-on; @@ -290,7 +284,6 @@ }; ldo1: LDO1 { /* NVCC_SNVS_1V8 */ - regulator-compatible = "LDO1"; regulator-min-microvolt = <1800000>; regulator-max-microvolt = <1800000>; regulator-always-on; @@ -298,7 +291,6 @@ }; ldo3: LDO3 { /* VDDA_1V8 */ - regulator-compatible = "LDO3"; regulator-min-microvolt = <1800000>; regulator-max-microvolt = <1800000>; regulator-always-on; @@ -306,13 +298,11 @@ }; ldo4: LDO4 { /* PMIC_LDO4 */ - regulator-compatible = "LDO4"; regulator-min-microvolt = <3300000>; regulator-max-microvolt = <3300000>; }; ldo5: LDO5 { /* NVCC_SD2 */ - regulator-compatible = "LDO5"; regulator-min-microvolt = <1800000>; regulator-max-microvolt = <3300000>; }; @@ -429,14 +419,15 @@ status = "okay"; /* - * PLL3 at 320 MHz supplies UART2 root with 64 MHz clock, - * which with 16x oversampling yields 4 Mbdps baud base, + * PLL1 at 80 MHz supplies UART2 root with 80 MHz clock, + * which with 16x oversampling yields 5 Mbdps baud base, + * which can be well divided by 5/4 to achieve 4 Mbdps, * which is exactly the maximum rate supported by muRata * 2AE bluetooth UART. */ - assigned-clocks = <&clk IMX8MP_SYS_PLL3>, <&clk IMX8MP_CLK_UART2>; - assigned-clock-parents = <0>, <&clk IMX8MP_SYS_PLL3_OUT>; - assigned-clock-rates = <320000000>, <64000000>; + assigned-clocks = <&clk IMX8MP_CLK_UART2>; + assigned-clock-parents = <&clk IMX8MP_SYS_PLL1_80M>; + assigned-clock-rates = <80000000>; bluetooth { pinctrl-names = "default"; diff --git a/arch/arm64/boot/dts/freescale/imx8mp-evk.dts b/arch/arm64/boot/dts/freescale/imx8mp-evk.dts index f2d93437084b..7816853162b3 100644 --- a/arch/arm64/boot/dts/freescale/imx8mp-evk.dts +++ b/arch/arm64/boot/dts/freescale/imx8mp-evk.dts @@ -400,13 +400,6 @@ pinctrl-names = "default"; pinctrl-0 = <&pinctrl_pcie0>; reset-gpio = <&gpio2 7 GPIO_ACTIVE_LOW>; - clocks = <&clk IMX8MP_CLK_HSIO_ROOT>, - <&clk IMX8MP_CLK_PCIE_ROOT>, - <&clk IMX8MP_CLK_HSIO_AXI>; - clock-names = "pcie", "pcie_aux", "pcie_bus"; - assigned-clocks = <&clk IMX8MP_CLK_PCIE_AUX>; - assigned-clock-rates = <10000000>; - assigned-clock-parents = <&clk IMX8MP_SYS_PLL2_50M>; vpcie-supply = <®_pcie0>; status = "okay"; }; diff --git a/arch/arm64/boot/dts/freescale/imx8mp-tqma8mpql-mba8mpxl-lvds.dtso b/arch/arm64/boot/dts/freescale/imx8mp-tqma8mpql-mba8mpxl-lvds.dtso new file mode 100644 index 000000000000..ea44d605342b --- /dev/null +++ b/arch/arm64/boot/dts/freescale/imx8mp-tqma8mpql-mba8mpxl-lvds.dtso @@ -0,0 +1,61 @@ +// SPDX-License-Identifier: (GPL-2.0-or-later OR MIT) +/* + * Copyright (c) 2022 TQ-Systems GmbH <linux@ew.tq-group.com>, + * D-82229 Seefeld, Germany. + * Author: Alexander Stein + */ + +/dts-v1/; +/plugin/; + +&{/} { + compatible = "tq,imx8mp-tqma8mpql-mba8mpxl", "tq,imx8mp-tqma8mpql", "fsl,imx8mp"; +}; + +&backlight_lvds { + status = "okay"; +}; + +&display { + compatible = "tianma,tm070jvhg33"; + status = "okay"; + + panel-timing { + clock-frequency = <74250000>; + hactive = <1280>; + vactive = <800>; + hfront-porch = <64>; + hback-porch = <5>; + hsync-len = <1>; + vfront-porch = <40>; + vback-porch = <2>; + vsync-len = <1>; + de-active = <1>; + }; + + port { + panel_in_lvds0: endpoint { + remote-endpoint = <&ldb_lvds_ch0>; + }; + }; +}; + +&lcdif2 { + status = "okay"; +}; + +&lvds_bridge { + status = "okay"; + + ports { + port@1 { + ldb_lvds_ch0: endpoint { + remote-endpoint = <&panel_in_lvds0>; + }; + }; + }; +}; + +&pwm2 { + status = "okay"; +}; diff --git a/arch/arm64/boot/dts/freescale/imx8mp-tqma8mpql-mba8mpxl.dts b/arch/arm64/boot/dts/freescale/imx8mp-tqma8mpql-mba8mpxl.dts index 6357f3d96ccd..3fa6cca9a043 100644 --- a/arch/arm64/boot/dts/freescale/imx8mp-tqma8mpql-mba8mpxl.dts +++ b/arch/arm64/boot/dts/freescale/imx8mp-tqma8mpql-mba8mpxl.dts @@ -447,9 +447,8 @@ sda-gpios = <&gpio5 17 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>; status = "okay"; - /* NXP SE97BTP with temperature sensor + eeprom */ - se97_1c: temperature-sensor-eeprom@1c { - compatible = "nxp,se97", "jedec,jc-42.4-temp"; + se97_1c: temperature-sensor@1c { + compatible = "nxp,se97b", "jedec,jc-42.4-temp"; reg = <0x1c>; }; diff --git a/arch/arm64/boot/dts/freescale/imx8mp-tqma8mpql.dtsi b/arch/arm64/boot/dts/freescale/imx8mp-tqma8mpql.dtsi index 7bd680a926ce..ebc29a950ba9 100644 --- a/arch/arm64/boot/dts/freescale/imx8mp-tqma8mpql.dtsi +++ b/arch/arm64/boot/dts/freescale/imx8mp-tqma8mpql.dtsi @@ -63,9 +63,8 @@ sda-gpios = <&gpio5 15 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>; status = "okay"; - /* NXP SE97BTP with temperature sensor + eeprom */ - se97: temperature-sensor-eeprom@1b { - compatible = "nxp,se97", "jedec,jc-42.4-temp"; + se97: temperature-sensor@1b { + compatible = "nxp,se97b", "jedec,jc-42.4-temp"; reg = <0x1b>; }; diff --git a/arch/arm64/boot/dts/freescale/imx8mp-venice-gw74xx.dts b/arch/arm64/boot/dts/freescale/imx8mp-venice-gw74xx.dts index 8eb7d5ee38da..eb51d648359b 100644 --- a/arch/arm64/boot/dts/freescale/imx8mp-venice-gw74xx.dts +++ b/arch/arm64/boot/dts/freescale/imx8mp-venice-gw74xx.dts @@ -593,13 +593,6 @@ pinctrl-names = "default"; pinctrl-0 = <&pinctrl_pcie0>; reset-gpio = <&gpio2 17 GPIO_ACTIVE_LOW>; - clocks = <&clk IMX8MP_CLK_HSIO_ROOT>, - <&clk IMX8MP_CLK_PCIE_ROOT>, - <&clk IMX8MP_CLK_HSIO_AXI>; - clock-names = "pcie", "pcie_aux", "pcie_bus"; - assigned-clocks = <&clk IMX8MP_CLK_PCIE_AUX>; - assigned-clock-rates = <10000000>; - assigned-clock-parents = <&clk IMX8MP_SYS_PLL2_50M>; status = "okay"; }; diff --git a/arch/arm64/boot/dts/freescale/imx8mp-verdin-dev.dtsi b/arch/arm64/boot/dts/freescale/imx8mp-verdin-dev.dtsi index cefabe65b252..361426c0da0a 100644 --- a/arch/arm64/boot/dts/freescale/imx8mp-verdin-dev.dtsi +++ b/arch/arm64/boot/dts/freescale/imx8mp-verdin-dev.dtsi @@ -3,8 +3,6 @@ * Copyright 2022 Toradex */ -#include "imx8mp-verdin-dahlia.dtsi" - / { /* TODO: Audio Codec */ @@ -21,16 +19,99 @@ }; }; +&backlight { + power-supply = <®_3p3v>; +}; + +/* Verdin SPI_1 */ +&ecspi1 { + status = "okay"; +}; + +/* EEPROM on display adapter boards */ +&eeprom_display_adapter { + status = "okay"; +}; + +/* EEPROM on Verdin Development board */ +&eeprom_carrier_board { + status = "okay"; +}; + +&eqos { + status = "okay"; +}; + &fec { phy-supply = <®_eth2phy>; status = "okay"; }; +&flexcan1 { + status = "okay"; +}; + +&flexcan2 { + status = "okay"; +}; + +/* Verdin QSPI_1 */ +&flexspi { + status = "okay"; +}; + &gpio_expander_21 { status = "okay"; vcc-supply = <®_1p8v>; }; +/* Current measurement into module VCC */ +&hwmon { + status = "okay"; +}; + +&hwmon_temp { + vs-supply = <®_1p8v>; + status = "okay"; +}; + +/* Verdin I2C_2_DSI */ +&i2c2 { + status = "okay"; +}; + +&i2c3 { + status = "okay"; +}; + +/* Verdin I2C_1 */ +&i2c4 { + status = "okay"; + + /* TODO: Audio Codec */ +}; + +/* TODO: Verdin PCIE_1 */ + +/* Verdin PWM_1 */ +&pwm1 { + status = "okay"; +}; + +/* Verdin PWM_2 */ +&pwm2 { + status = "okay"; +}; + +/* Verdin PWM_3_DSI */ +&pwm3 { + status = "okay"; +}; + +®_usdhc2_vmmc { + vin-supply = <®_3p3v>; +}; + /* TODO: Verdin I2C_1 with Audio Codec */ /* Verdin UART_1, connector X50 through RS485 transceiver */ @@ -38,9 +119,40 @@ linux,rs485-enabled-at-boot-time; rs485-rts-active-low; rs485-rx-during-tx; + status = "okay"; +}; + +/* Verdin UART_2 */ +&uart2 { + status = "okay"; +}; + +/* Verdin UART_3, used as the Linux Console */ +&uart3 { + status = "okay"; +}; + +/* Verdin USB_1 */ +&usb3_0 { + status = "okay"; +}; + +&usb3_phy0 { + status = "okay"; +}; + +/* Verdin USB_2 */ +&usb3_1 { + fsl,permanently-attached; + status = "okay"; +}; + +&usb3_phy1 { + status = "okay"; }; /* Limit frequency on dev board due to long traces and bad signal integrity */ &usdhc2 { max-frequency = <100000000>; + status = "okay"; }; diff --git a/arch/arm64/boot/dts/freescale/imx8mp-verdin-nonwifi-yavia.dts b/arch/arm64/boot/dts/freescale/imx8mp-verdin-nonwifi-yavia.dts new file mode 100644 index 000000000000..b28477df1ec6 --- /dev/null +++ b/arch/arm64/boot/dts/freescale/imx8mp-verdin-nonwifi-yavia.dts @@ -0,0 +1,18 @@ +// SPDX-License-Identifier: GPL-2.0-or-later OR MIT +/* + * Copyright 2023 Toradex + */ + +/dts-v1/; + +#include "imx8mp-verdin.dtsi" +#include "imx8mp-verdin-nonwifi.dtsi" +#include "imx8mp-verdin-yavia.dtsi" + +/ { + model = "Toradex Verdin iMX8M Plus on Yavia Board"; + compatible = "toradex,verdin-imx8mp-nonwifi-yavia", + "toradex,verdin-imx8mp-nonwifi", + "toradex,verdin-imx8mp", + "fsl,imx8mp"; +}; diff --git a/arch/arm64/boot/dts/freescale/imx8mp-verdin-wifi-yavia.dts b/arch/arm64/boot/dts/freescale/imx8mp-verdin-wifi-yavia.dts new file mode 100644 index 000000000000..100bef12089c --- /dev/null +++ b/arch/arm64/boot/dts/freescale/imx8mp-verdin-wifi-yavia.dts @@ -0,0 +1,18 @@ +// SPDX-License-Identifier: GPL-2.0-or-later OR MIT +/* + * Copyright 2023 Toradex + */ + +/dts-v1/; + +#include "imx8mp-verdin.dtsi" +#include "imx8mp-verdin-wifi.dtsi" +#include "imx8mp-verdin-yavia.dtsi" + +/ { + model = "Toradex Verdin iMX8M Plus WB on Yavia Board"; + compatible = "toradex,verdin-imx8mp-wifi-yavia", + "toradex,verdin-imx8mp-wifi", + "toradex,verdin-imx8mp", + "fsl,imx8mp"; +}; diff --git a/arch/arm64/boot/dts/freescale/imx8mp-verdin-yavia.dtsi b/arch/arm64/boot/dts/freescale/imx8mp-verdin-yavia.dtsi new file mode 100644 index 000000000000..bd7b31cc3760 --- /dev/null +++ b/arch/arm64/boot/dts/freescale/imx8mp-verdin-yavia.dtsi @@ -0,0 +1,213 @@ +// SPDX-License-Identifier: GPL-2.0-or-later OR MIT +/* + * Copyright 2023 Toradex + */ + +#include <dt-bindings/leds/common.h> + +/ { + /* Carrier Board Supply +V1.8 */ + reg_1p8v: regulator-1p8v { + compatible = "regulator-fixed"; + regulator-max-microvolt = <1800000>; + regulator-min-microvolt = <1800000>; + regulator-name = "+V1.8_SW"; + }; + + /* Carrier Board Supply +V3.3 */ + reg_3p3v: regulator-3p3v { + compatible = "regulator-fixed"; + regulator-max-microvolt = <3300000>; + regulator-min-microvolt = <3300000>; + regulator-name = "+V3.3_SW"; + }; + + leds { + compatible = "gpio-leds"; + + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_leds_yavia>; + + /* SODIMM 52 - LD1_RED */ + led-0 { + color = <LED_COLOR_ID_RED>; + function = LED_FUNCTION_DEBUG; + function-enumerator = <1>; + gpios = <&gpio3 0 GPIO_ACTIVE_HIGH>; + }; + /* SODIMM 54 - LD1_GREEN */ + led-1 { + color = <LED_COLOR_ID_GREEN>; + function = LED_FUNCTION_DEBUG; + function-enumerator = <1>; + gpios = <&gpio3 1 GPIO_ACTIVE_HIGH>; + }; + /* SODIMM 56 - LD1_BLUE */ + led-2 { + color = <LED_COLOR_ID_BLUE>; + function = LED_FUNCTION_DEBUG; + function-enumerator = <1>; + gpios = <&gpio3 6 GPIO_ACTIVE_HIGH>; + }; + /* SODIMM 58 - LD2_RED */ + led-3 { + color = <LED_COLOR_ID_RED>; + function = LED_FUNCTION_DEBUG; + function-enumerator = <2>; + gpios = <&gpio3 7 GPIO_ACTIVE_HIGH>; + }; + /* SODIMM 60 - LD2_GREEN */ + led-4 { + color = <LED_COLOR_ID_GREEN>; + function = LED_FUNCTION_DEBUG; + function-enumerator = <2>; + gpios = <&gpio3 8 GPIO_ACTIVE_HIGH>; + }; + /* SODIMM 62 - LD2_BLUE */ + led-5 { + color = <LED_COLOR_ID_BLUE>; + function = LED_FUNCTION_DEBUG; + function-enumerator = <2>; + gpios = <&gpio3 9 GPIO_ACTIVE_HIGH>; + }; + }; +}; + +&backlight { + power-supply = <®_3p3v>; +}; + +/* Verdin SPI_1 */ +&ecspi1 { + status = "okay"; +}; + +/* EEPROM on display adapter boards */ +&eeprom_display_adapter { + status = "okay"; +}; + +/* EEPROM on Verdin yavia board */ +&eeprom_carrier_board { + status = "okay"; +}; + +&eqos { + status = "okay"; +}; + +&flexcan1 { + status = "okay"; +}; + +&hwmon_temp { + status = "okay"; +}; + +/* Verdin I2C_2_DSI */ +&i2c2 { + status = "okay"; +}; + +&i2c3 { + status = "okay"; +}; + +&i2c4 { + status = "okay"; +}; + +/* Verdin PCIE_1 */ +&pcie { + status = "okay"; +}; + +&pcie_phy{ + status = "okay"; +}; + +/* Verdin PWM_1 */ +&pwm1 { + status = "okay"; +}; + +/* Verdin PWM_2 */ +&pwm2 { + status = "okay"; +}; + +/* Verdin PWM_3_DSI */ +&pwm3 { + status = "okay"; +}; + +®_usdhc2_vmmc { + vin-supply = <®_3p3v>; +}; + +/* Verdin UART_1 */ +&uart1 { + status = "okay"; +}; + +/* Verdin UART_2 */ +&uart2 { + status = "okay"; +}; + +/* Verdin UART_3, used as the Linux Console */ +&uart3 { + status = "okay"; +}; + +/* Verdin USB_1 */ +&usb3_phy0 { + status = "okay"; +}; + +&usb3_0 { + status = "okay"; +}; + +&usb_dwc3_0 { + status = "okay"; +}; + +/* Verdin USB_2 */ +&usb3_phy1 { + status = "okay"; +}; + +&usb3_1 { + status = "okay"; +}; + +&usb_dwc3_1 { + disable-over-current; + status = "okay"; +}; + +/* Verdin SD_1 */ +&usdhc2 { + status = "okay"; +}; + +&iomuxc { + pinctrl_leds_yavia: ledsyaviagrp { + fsl,pins = < + MX8MP_IOMUXC_NAND_ALE__GPIO3_IO00 0x106 /* SODIMM 52 */ + MX8MP_IOMUXC_NAND_CE0_B__GPIO3_IO01 0x106 /* SODIMM 54 */ + MX8MP_IOMUXC_NAND_DATA00__GPIO3_IO06 0x106 /* SODIMM 56 */ + MX8MP_IOMUXC_NAND_DATA01__GPIO3_IO07 0x106 /* SODIMM 58 */ + MX8MP_IOMUXC_NAND_DATA02__GPIO3_IO08 0x106 /* SODIMM 60 */ + MX8MP_IOMUXC_NAND_DATA03__GPIO3_IO09 0x106 /* SODIMM 62 */ + >; + }; + + pinctrl_gpios_ext_yavia: gpiosextyaviagrp { + fsl,pins = < + MX8MP_IOMUXC_NAND_CE1_B__GPIO3_IO02 0x106 /* SODIMM 64 */ + MX8MP_IOMUXC_NAND_DQS__GPIO3_IO14 0x106 /* SODIMM 66 */ + >; + }; +}; diff --git a/arch/arm64/boot/dts/freescale/imx8mp-verdin.dtsi b/arch/arm64/boot/dts/freescale/imx8mp-verdin.dtsi index 6a1890a4b5d8..0dd6180a8e39 100644 --- a/arch/arm64/boot/dts/freescale/imx8mp-verdin.dtsi +++ b/arch/arm64/boot/dts/freescale/imx8mp-verdin.dtsi @@ -50,7 +50,7 @@ pinctrl-names = "default"; pinctrl-0 = <&pinctrl_gpio_keys>; - button-wakeup { + key-wakeup { debounce-interval = <10>; /* Verdin CTRL_WAKE1_MICO# (SODIMM 252) */ gpios = <&gpio4 0 GPIO_ACTIVE_LOW>; @@ -453,7 +453,6 @@ pinctrl-names = "default"; pinctrl-0 = <&pinctrl_pmic>; reg = <0x25>; - sd-vsel-gpios = <&gpio1 4 GPIO_ACTIVE_HIGH>; /* * The bootloader is expected to switch on LDO4 for the on-module +V3.3_ADC and the diff --git a/arch/arm64/boot/dts/freescale/imx8mp.dtsi b/arch/arm64/boot/dts/freescale/imx8mp.dtsi index 03034b439c1f..a19224fe1a6a 100644 --- a/arch/arm64/boot/dts/freescale/imx8mp.dtsi +++ b/arch/arm64/boot/dts/freescale/imx8mp.dtsi @@ -380,6 +380,8 @@ compatible = "fsl,imx8mp-tmu"; reg = <0x30260000 0x10000>; clocks = <&clk IMX8MP_CLK_TSENSOR_ROOT>; + nvmem-cells = <&tmu_calib>; + nvmem-cell-names = "calib"; #thermal-sensor-cells = <1>; }; @@ -412,7 +414,7 @@ reg = <0x30330000 0x10000>; }; - gpr: iomuxc-gpr@30340000 { + gpr: syscon@30340000 { compatible = "fsl,imx8mp-iomuxc-gpr", "syscon"; reg = <0x30340000 0x10000>; }; @@ -425,21 +427,38 @@ #address-cells = <1>; #size-cells = <1>; - imx8mp_uid: unique-id@420 { + /* + * The register address below maps to the MX8M + * Fusemap Description Table entries this way. + * Assuming + * reg = <ADDR SIZE>; + * then + * Fuse Address = (ADDR * 4) + 0x400 + * Note that if SIZE is greater than 4, then + * each subsequent fuse is located at offset + * +0x10 in Fusemap Description Table (e.g. + * reg = <0x8 0x8> describes fuses 0x420 and + * 0x430). + */ + imx8mp_uid: unique-id@8 { /* 0x420-0x430 */ reg = <0x8 0x8>; }; - cpu_speed_grade: speed-grade@10 { + cpu_speed_grade: speed-grade@10 { /* 0x440 */ reg = <0x10 4>; }; - eth_mac1: mac-address@90 { + eth_mac1: mac-address@90 { /* 0x640 */ reg = <0x90 6>; }; - eth_mac2: mac-address@96 { + eth_mac2: mac-address@96 { /* 0x658 */ reg = <0x96 6>; }; + + tmu_calib: calib@264 { /* 0xd90-0xdc0 */ + reg = <0x264 0x10>; + }; }; anatop: clock-controller@30360000 { @@ -712,121 +731,129 @@ #size-cells = <1>; ranges; - ecspi1: spi@30820000 { + spba-bus@30800000 { + compatible = "fsl,spba-bus", "simple-bus"; + reg = <0x30800000 0x100000>; #address-cells = <1>; - #size-cells = <0>; - compatible = "fsl,imx8mp-ecspi", "fsl,imx6ul-ecspi"; - reg = <0x30820000 0x10000>; - interrupts = <GIC_SPI 31 IRQ_TYPE_LEVEL_HIGH>; - clocks = <&clk IMX8MP_CLK_ECSPI1_ROOT>, - <&clk IMX8MP_CLK_ECSPI1_ROOT>; - clock-names = "ipg", "per"; - assigned-clock-rates = <80000000>; - assigned-clocks = <&clk IMX8MP_CLK_ECSPI1>; - assigned-clock-parents = <&clk IMX8MP_SYS_PLL1_800M>; - dmas = <&sdma1 0 7 1>, <&sdma1 1 7 2>; - dma-names = "rx", "tx"; - status = "disabled"; - }; + #size-cells = <1>; + ranges; - ecspi2: spi@30830000 { - #address-cells = <1>; - #size-cells = <0>; - compatible = "fsl,imx8mp-ecspi", "fsl,imx6ul-ecspi"; - reg = <0x30830000 0x10000>; - interrupts = <GIC_SPI 32 IRQ_TYPE_LEVEL_HIGH>; - clocks = <&clk IMX8MP_CLK_ECSPI2_ROOT>, - <&clk IMX8MP_CLK_ECSPI2_ROOT>; - clock-names = "ipg", "per"; - assigned-clock-rates = <80000000>; - assigned-clocks = <&clk IMX8MP_CLK_ECSPI2>; - assigned-clock-parents = <&clk IMX8MP_SYS_PLL1_800M>; - dmas = <&sdma1 2 7 1>, <&sdma1 3 7 2>; - dma-names = "rx", "tx"; - status = "disabled"; - }; + ecspi1: spi@30820000 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "fsl,imx8mp-ecspi", "fsl,imx6ul-ecspi"; + reg = <0x30820000 0x10000>; + interrupts = <GIC_SPI 31 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&clk IMX8MP_CLK_ECSPI1_ROOT>, + <&clk IMX8MP_CLK_ECSPI1_ROOT>; + clock-names = "ipg", "per"; + assigned-clock-rates = <80000000>; + assigned-clocks = <&clk IMX8MP_CLK_ECSPI1>; + assigned-clock-parents = <&clk IMX8MP_SYS_PLL1_800M>; + dmas = <&sdma1 0 7 1>, <&sdma1 1 7 2>; + dma-names = "rx", "tx"; + status = "disabled"; + }; - ecspi3: spi@30840000 { - #address-cells = <1>; - #size-cells = <0>; - compatible = "fsl,imx8mp-ecspi", "fsl,imx6ul-ecspi"; - reg = <0x30840000 0x10000>; - interrupts = <GIC_SPI 33 IRQ_TYPE_LEVEL_HIGH>; - clocks = <&clk IMX8MP_CLK_ECSPI3_ROOT>, - <&clk IMX8MP_CLK_ECSPI3_ROOT>; - clock-names = "ipg", "per"; - assigned-clock-rates = <80000000>; - assigned-clocks = <&clk IMX8MP_CLK_ECSPI3>; - assigned-clock-parents = <&clk IMX8MP_SYS_PLL1_800M>; - dmas = <&sdma1 4 7 1>, <&sdma1 5 7 2>; - dma-names = "rx", "tx"; - status = "disabled"; - }; + ecspi2: spi@30830000 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "fsl,imx8mp-ecspi", "fsl,imx6ul-ecspi"; + reg = <0x30830000 0x10000>; + interrupts = <GIC_SPI 32 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&clk IMX8MP_CLK_ECSPI2_ROOT>, + <&clk IMX8MP_CLK_ECSPI2_ROOT>; + clock-names = "ipg", "per"; + assigned-clock-rates = <80000000>; + assigned-clocks = <&clk IMX8MP_CLK_ECSPI2>; + assigned-clock-parents = <&clk IMX8MP_SYS_PLL1_800M>; + dmas = <&sdma1 2 7 1>, <&sdma1 3 7 2>; + dma-names = "rx", "tx"; + status = "disabled"; + }; - uart1: serial@30860000 { - compatible = "fsl,imx8mp-uart", "fsl,imx6q-uart"; - reg = <0x30860000 0x10000>; - interrupts = <GIC_SPI 26 IRQ_TYPE_LEVEL_HIGH>; - clocks = <&clk IMX8MP_CLK_UART1_ROOT>, - <&clk IMX8MP_CLK_UART1_ROOT>; - clock-names = "ipg", "per"; - dmas = <&sdma1 22 4 0>, <&sdma1 23 4 0>; - dma-names = "rx", "tx"; - status = "disabled"; - }; + ecspi3: spi@30840000 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "fsl,imx8mp-ecspi", "fsl,imx6ul-ecspi"; + reg = <0x30840000 0x10000>; + interrupts = <GIC_SPI 33 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&clk IMX8MP_CLK_ECSPI3_ROOT>, + <&clk IMX8MP_CLK_ECSPI3_ROOT>; + clock-names = "ipg", "per"; + assigned-clock-rates = <80000000>; + assigned-clocks = <&clk IMX8MP_CLK_ECSPI3>; + assigned-clock-parents = <&clk IMX8MP_SYS_PLL1_800M>; + dmas = <&sdma1 4 7 1>, <&sdma1 5 7 2>; + dma-names = "rx", "tx"; + status = "disabled"; + }; - uart3: serial@30880000 { - compatible = "fsl,imx8mp-uart", "fsl,imx6q-uart"; - reg = <0x30880000 0x10000>; - interrupts = <GIC_SPI 28 IRQ_TYPE_LEVEL_HIGH>; - clocks = <&clk IMX8MP_CLK_UART3_ROOT>, - <&clk IMX8MP_CLK_UART3_ROOT>; - clock-names = "ipg", "per"; - dmas = <&sdma1 26 4 0>, <&sdma1 27 4 0>; - dma-names = "rx", "tx"; - status = "disabled"; - }; + uart1: serial@30860000 { + compatible = "fsl,imx8mp-uart", "fsl,imx6q-uart"; + reg = <0x30860000 0x10000>; + interrupts = <GIC_SPI 26 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&clk IMX8MP_CLK_UART1_ROOT>, + <&clk IMX8MP_CLK_UART1_ROOT>; + clock-names = "ipg", "per"; + dmas = <&sdma1 22 4 0>, <&sdma1 23 4 0>; + dma-names = "rx", "tx"; + status = "disabled"; + }; - uart2: serial@30890000 { - compatible = "fsl,imx8mp-uart", "fsl,imx6q-uart"; - reg = <0x30890000 0x10000>; - interrupts = <GIC_SPI 27 IRQ_TYPE_LEVEL_HIGH>; - clocks = <&clk IMX8MP_CLK_UART2_ROOT>, - <&clk IMX8MP_CLK_UART2_ROOT>; - clock-names = "ipg", "per"; - dmas = <&sdma1 24 4 0>, <&sdma1 25 4 0>; - dma-names = "rx", "tx"; - status = "disabled"; - }; + uart3: serial@30880000 { + compatible = "fsl,imx8mp-uart", "fsl,imx6q-uart"; + reg = <0x30880000 0x10000>; + interrupts = <GIC_SPI 28 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&clk IMX8MP_CLK_UART3_ROOT>, + <&clk IMX8MP_CLK_UART3_ROOT>; + clock-names = "ipg", "per"; + dmas = <&sdma1 26 4 0>, <&sdma1 27 4 0>; + dma-names = "rx", "tx"; + status = "disabled"; + }; - flexcan1: can@308c0000 { - compatible = "fsl,imx8mp-flexcan"; - reg = <0x308c0000 0x10000>; - interrupts = <GIC_SPI 142 IRQ_TYPE_LEVEL_HIGH>; - clocks = <&clk IMX8MP_CLK_IPG_ROOT>, - <&clk IMX8MP_CLK_CAN1_ROOT>; - clock-names = "ipg", "per"; - assigned-clocks = <&clk IMX8MP_CLK_CAN1>; - assigned-clock-parents = <&clk IMX8MP_SYS_PLL1_40M>; - assigned-clock-rates = <40000000>; - fsl,clk-source = /bits/ 8 <0>; - fsl,stop-mode = <&gpr 0x10 4>; - status = "disabled"; - }; + uart2: serial@30890000 { + compatible = "fsl,imx8mp-uart", "fsl,imx6q-uart"; + reg = <0x30890000 0x10000>; + interrupts = <GIC_SPI 27 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&clk IMX8MP_CLK_UART2_ROOT>, + <&clk IMX8MP_CLK_UART2_ROOT>; + clock-names = "ipg", "per"; + dmas = <&sdma1 24 4 0>, <&sdma1 25 4 0>; + dma-names = "rx", "tx"; + status = "disabled"; + }; - flexcan2: can@308d0000 { - compatible = "fsl,imx8mp-flexcan"; - reg = <0x308d0000 0x10000>; - interrupts = <GIC_SPI 144 IRQ_TYPE_LEVEL_HIGH>; - clocks = <&clk IMX8MP_CLK_IPG_ROOT>, - <&clk IMX8MP_CLK_CAN2_ROOT>; - clock-names = "ipg", "per"; - assigned-clocks = <&clk IMX8MP_CLK_CAN2>; - assigned-clock-parents = <&clk IMX8MP_SYS_PLL1_40M>; - assigned-clock-rates = <40000000>; - fsl,clk-source = /bits/ 8 <0>; - fsl,stop-mode = <&gpr 0x10 5>; - status = "disabled"; + flexcan1: can@308c0000 { + compatible = "fsl,imx8mp-flexcan"; + reg = <0x308c0000 0x10000>; + interrupts = <GIC_SPI 142 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&clk IMX8MP_CLK_IPG_ROOT>, + <&clk IMX8MP_CLK_CAN1_ROOT>; + clock-names = "ipg", "per"; + assigned-clocks = <&clk IMX8MP_CLK_CAN1>; + assigned-clock-parents = <&clk IMX8MP_SYS_PLL1_40M>; + assigned-clock-rates = <40000000>; + fsl,clk-source = /bits/ 8 <0>; + fsl,stop-mode = <&gpr 0x10 4>; + status = "disabled"; + }; + + flexcan2: can@308d0000 { + compatible = "fsl,imx8mp-flexcan"; + reg = <0x308d0000 0x10000>; + interrupts = <GIC_SPI 144 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&clk IMX8MP_CLK_IPG_ROOT>, + <&clk IMX8MP_CLK_CAN2_ROOT>; + clock-names = "ipg", "per"; + assigned-clocks = <&clk IMX8MP_CLK_CAN2>; + assigned-clock-parents = <&clk IMX8MP_SYS_PLL1_40M>; + assigned-clock-rates = <40000000>; + fsl,clk-source = /bits/ 8 <0>; + fsl,stop-mode = <&gpr 0x10 5>; + status = "disabled"; + }; }; crypto: crypto@30900000 { @@ -1099,10 +1126,35 @@ #size-cells = <1>; ranges; + lcdif2: display-controller@32e90000 { + compatible = "fsl,imx8mp-lcdif"; + reg = <0x32e90000 0x238>; + interrupts = <GIC_SPI 6 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&clk IMX8MP_CLK_MEDIA_DISP2_PIX_ROOT>, + <&clk IMX8MP_CLK_MEDIA_AXI_ROOT>, + <&clk IMX8MP_CLK_MEDIA_APB_ROOT>; + clock-names = "pix", "axi", "disp_axi"; + assigned-clocks = <&clk IMX8MP_CLK_MEDIA_DISP2_PIX>, + <&clk IMX8MP_VIDEO_PLL1>; + assigned-clock-parents = <&clk IMX8MP_VIDEO_PLL1_OUT>, + <&clk IMX8MP_VIDEO_PLL1_REF_SEL>; + assigned-clock-rates = <0>, <1039500000>; + power-domains = <&media_blk_ctrl IMX8MP_MEDIABLK_PD_LCDIF_2>; + status = "disabled"; + + port { + lcdif2_to_ldb: endpoint { + remote-endpoint = <&ldb_from_lcdif2>; + }; + }; + }; + media_blk_ctrl: blk-ctrl@32ec0000 { compatible = "fsl,imx8mp-media-blk-ctrl", - "syscon"; + "simple-bus", "syscon"; reg = <0x32ec0000 0x10000>; + #address-cells = <1>; + #size-cells = <1>; power-domains = <&pgc_mediamix>, <&pgc_mipi_phy1>, <&pgc_mipi_phy1>, @@ -1147,6 +1199,44 @@ assigned-clock-rates = <500000000>, <200000000>; #power-domain-cells = <1>; + + lvds_bridge: bridge@5c { + compatible = "fsl,imx8mp-ldb"; + clocks = <&clk IMX8MP_CLK_MEDIA_LDB>; + clock-names = "ldb"; + reg = <0x5c 0x4>, <0x128 0x4>; + reg-names = "ldb", "lvds"; + assigned-clocks = <&clk IMX8MP_CLK_MEDIA_LDB>; + assigned-clock-parents = <&clk IMX8MP_VIDEO_PLL1_OUT>; + status = "disabled"; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + + ldb_from_lcdif2: endpoint { + remote-endpoint = <&lcdif2_to_ldb>; + }; + }; + + port@1 { + reg = <1>; + + ldb_lvds_ch0: endpoint { + }; + }; + + port@2 { + reg = <2>; + + ldb_lvds_ch1: endpoint { + }; + }; + }; + }; }; pcie_phy: pcie-phy@32f00000 { @@ -1177,6 +1267,7 @@ <&noc IMX8MP_ICM_PCIE &noc IMX8MP_ICN_HSIO>; interconnect-names = "noc-pcie", "usb1", "usb2", "pcie"; #power-domain-cells = <1>; + #clock-cells = <0>; }; }; @@ -1184,6 +1275,13 @@ compatible = "fsl,imx8mp-pcie"; reg = <0x33800000 0x400000>, <0x1ff00000 0x80000>; reg-names = "dbi", "config"; + clocks = <&clk IMX8MP_CLK_HSIO_ROOT>, + <&clk IMX8MP_CLK_HSIO_AXI>, + <&clk IMX8MP_CLK_PCIE_ROOT>; + clock-names = "pcie", "pcie_bus", "pcie_aux"; + assigned-clocks = <&clk IMX8MP_CLK_PCIE_AUX>; + assigned-clock-rates = <10000000>; + assigned-clock-parents = <&clk IMX8MP_SYS_PLL2_50M>; #address-cells = <3>; #size-cells = <2>; device_type = "pci"; @@ -1242,6 +1340,28 @@ power-domains = <&pgc_gpu2d>; }; + vpu_g1: video-codec@38300000 { + compatible = "nxp,imx8mm-vpu-g1"; + reg = <0x38300000 0x10000>; + interrupts = <GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&clk IMX8MP_CLK_VPU_G1_ROOT>; + assigned-clocks = <&clk IMX8MP_CLK_VPU_G1>; + assigned-clock-parents = <&clk IMX8MP_VPU_PLL_OUT>; + assigned-clock-rates = <600000000>; + power-domains = <&vpumix_blk_ctrl IMX8MP_VPUBLK_PD_G1>; + }; + + vpu_g2: video-codec@38310000 { + compatible = "nxp,imx8mq-vpu-g2"; + reg = <0x38310000 0x10000>; + interrupts = <GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&clk IMX8MP_CLK_VPU_G2_ROOT>; + assigned-clocks = <&clk IMX8MP_CLK_VPU_G2>; + assigned-clock-parents = <&clk IMX8MP_SYS_PLL2_1000M>; + assigned-clock-rates = <500000000>; + power-domains = <&vpumix_blk_ctrl IMX8MP_VPUBLK_PD_G2>; + }; + vpumix_blk_ctrl: blk-ctrl@38330000 { compatible = "fsl,imx8mp-vpu-blk-ctrl", "syscon"; reg = <0x38330000 0x100>; @@ -1253,6 +1373,9 @@ <&clk IMX8MP_CLK_VPU_G2_ROOT>, <&clk IMX8MP_CLK_VPU_VC8KE_ROOT>; clock-names = "g1", "g2", "vc8000e"; + assigned-clocks = <&clk IMX8MP_CLK_VPU_BUS>, <&clk IMX8MP_VPU_PLL>; + assigned-clock-parents = <&clk IMX8MP_VPU_PLL_OUT>; + assigned-clock-rates = <600000000>, <600000000>; interconnects = <&noc IMX8MP_ICM_VPU_G1 &noc IMX8MP_ICN_VIDEO>, <&noc IMX8MP_ICM_VPU_G2 &noc IMX8MP_ICN_VIDEO>, <&noc IMX8MP_ICM_VPU_H1 &noc IMX8MP_ICN_VIDEO>; diff --git a/arch/arm64/boot/dts/freescale/imx8mq-evk.dts b/arch/arm64/boot/dts/freescale/imx8mq-evk.dts index 78937910f403..7507548cdb16 100644 --- a/arch/arm64/boot/dts/freescale/imx8mq-evk.dts +++ b/arch/arm64/boot/dts/freescale/imx8mq-evk.dts @@ -356,10 +356,9 @@ pinctrl-0 = <&pinctrl_pcie0>; reset-gpio = <&gpio5 28 GPIO_ACTIVE_LOW>; clocks = <&clk IMX8MQ_CLK_PCIE1_ROOT>, - <&clk IMX8MQ_CLK_PCIE1_AUX>, + <&pcie0_refclk>, <&clk IMX8MQ_CLK_PCIE1_PHY>, - <&pcie0_refclk>; - clock-names = "pcie", "pcie_aux", "pcie_phy", "pcie_bus"; + <&clk IMX8MQ_CLK_PCIE1_AUX>; vph-supply = <&vgen5_reg>; status = "okay"; }; @@ -369,10 +368,9 @@ pinctrl-0 = <&pinctrl_pcie1>; reset-gpio = <&gpio5 12 GPIO_ACTIVE_LOW>; clocks = <&clk IMX8MQ_CLK_PCIE2_ROOT>, - <&clk IMX8MQ_CLK_PCIE2_AUX>, + <&pcie0_refclk>, <&clk IMX8MQ_CLK_PCIE2_PHY>, - <&pcie0_refclk>; - clock-names = "pcie", "pcie_aux", "pcie_phy", "pcie_bus"; + <&clk IMX8MQ_CLK_PCIE2_AUX>; vpcie-supply = <®_pcie1>; vph-supply = <&vgen5_reg>; status = "okay"; diff --git a/arch/arm64/boot/dts/freescale/imx8mq-kontron-pitx-imx8m.dts b/arch/arm64/boot/dts/freescale/imx8mq-kontron-pitx-imx8m.dts index a91c136797f6..6376417e918c 100644 --- a/arch/arm64/boot/dts/freescale/imx8mq-kontron-pitx-imx8m.dts +++ b/arch/arm64/boot/dts/freescale/imx8mq-kontron-pitx-imx8m.dts @@ -245,20 +245,18 @@ pinctrl-0 = <&pinctrl_pcie0>; reset-gpio = <&gpio1 9 GPIO_ACTIVE_LOW>; clocks = <&clk IMX8MQ_CLK_PCIE1_ROOT>, - <&clk IMX8MQ_CLK_PCIE1_AUX>, + <&pcie0_refclk>, <&clk IMX8MQ_CLK_PCIE1_PHY>, - <&pcie0_refclk>; - clock-names = "pcie", "pcie_aux", "pcie_phy", "pcie_bus"; + <&clk IMX8MQ_CLK_PCIE1_AUX>; status = "okay"; }; /* Intel Ethernet Controller I210/I211 */ &pcie1 { clocks = <&clk IMX8MQ_CLK_PCIE2_ROOT>, - <&clk IMX8MQ_CLK_PCIE2_AUX>, + <&pcie1_refclk>, <&clk IMX8MQ_CLK_PCIE2_PHY>, - <&pcie1_refclk>; - clock-names = "pcie", "pcie_aux", "pcie_phy", "pcie_bus"; + <&clk IMX8MQ_CLK_PCIE2_AUX>; fsl,max-link-speed = <1>; status = "okay"; }; diff --git a/arch/arm64/boot/dts/freescale/imx8mq-librem5-devkit.dts b/arch/arm64/boot/dts/freescale/imx8mq-librem5-devkit.dts index 4c8904fba1c1..7605802f294d 100644 --- a/arch/arm64/boot/dts/freescale/imx8mq-librem5-devkit.dts +++ b/arch/arm64/boot/dts/freescale/imx8mq-librem5-devkit.dts @@ -64,7 +64,7 @@ leds { compatible = "pwm-leds"; - led1 { + led-1 { function = LED_FUNCTION_STATUS; color = <LED_COLOR_ID_RED>; max-brightness = <248>; diff --git a/arch/arm64/boot/dts/freescale/imx8mq-librem5.dtsi b/arch/arm64/boot/dts/freescale/imx8mq-librem5.dtsi index ddf0e330dc7c..6895bcc12165 100644 --- a/arch/arm64/boot/dts/freescale/imx8mq-librem5.dtsi +++ b/arch/arm64/boot/dts/freescale/imx8mq-librem5.dtsi @@ -56,27 +56,27 @@ }; led-controller { - compatible = "pwm-leds"; + compatible = "pwm-leds-multicolor"; - led-0 { + multi-led { + color = <LED_COLOR_ID_RGB>; function = LED_FUNCTION_STATUS; - color = <LED_COLOR_ID_BLUE>; max-brightness = <248>; - pwms = <&pwm2 0 50000 0>; - }; - led-1 { - function = LED_FUNCTION_STATUS; - color = <LED_COLOR_ID_GREEN>; - max-brightness = <248>; - pwms = <&pwm4 0 50000 0>; - }; + led-0 { + color = <LED_COLOR_ID_BLUE>; + pwms = <&pwm2 0 50000 0>; + }; - led-2 { - function = LED_FUNCTION_STATUS; - color = <LED_COLOR_ID_RED>; - max-brightness = <248>; - pwms = <&pwm3 0 50000 0>; + led-1 { + color = <LED_COLOR_ID_GREEN>; + pwms = <&pwm4 0 50000 0>; + }; + + led-2 { + color = <LED_COLOR_ID_RED>; + pwms = <&pwm3 0 50000 0>; + }; }; }; diff --git a/arch/arm64/boot/dts/freescale/imx8mq-mnt-reform2.dts b/arch/arm64/boot/dts/freescale/imx8mq-mnt-reform2.dts index 055031bba8c4..200268660518 100644 --- a/arch/arm64/boot/dts/freescale/imx8mq-mnt-reform2.dts +++ b/arch/arm64/boot/dts/freescale/imx8mq-mnt-reform2.dts @@ -197,10 +197,9 @@ pinctrl-0 = <&pinctrl_pcie1>; reset-gpio = <&gpio3 23 GPIO_ACTIVE_LOW>; clocks = <&clk IMX8MQ_CLK_PCIE2_ROOT>, - <&clk IMX8MQ_CLK_PCIE2_AUX>, + <&pcie1_refclk>, <&clk IMX8MQ_CLK_PCIE2_PHY>, - <&pcie1_refclk>; - clock-names = "pcie", "pcie_aux", "pcie_phy", "pcie_bus"; + <&clk IMX8MQ_CLK_PCIE2_AUX>; status = "okay"; }; diff --git a/arch/arm64/boot/dts/freescale/imx8mq-tqma8mq-mba8mx.dts b/arch/arm64/boot/dts/freescale/imx8mq-tqma8mq-mba8mx.dts index d7660eab68b9..344cfdaeb1d5 100644 --- a/arch/arm64/boot/dts/freescale/imx8mq-tqma8mq-mba8mx.dts +++ b/arch/arm64/boot/dts/freescale/imx8mq-tqma8mq-mba8mx.dts @@ -105,10 +105,9 @@ &pcie0 { reset-gpio = <&expander0 14 GPIO_ACTIVE_LOW>; clocks = <&clk IMX8MQ_CLK_PCIE1_ROOT>, - <&clk IMX8MQ_CLK_PCIE1_AUX>, + <&pcie0_refclk>, <&clk IMX8MQ_CLK_PCIE1_PHY>, - <&pcie0_refclk>; - clock-names = "pcie", "pcie_aux", "pcie_phy", "pcie_bus"; + <&clk IMX8MQ_CLK_PCIE1_AUX>; epdev_on-supply = <®_vcc_3v3>; hard-wired = <1>; status = "okay"; @@ -120,10 +119,9 @@ */ &pcie1 { clocks = <&clk IMX8MQ_CLK_PCIE2_ROOT>, - <&clk IMX8MQ_CLK_PCIE2_AUX>, + <&pcie1_refclk>, <&clk IMX8MQ_CLK_PCIE2_PHY>, - <&pcie1_refclk>; - clock-names = "pcie", "pcie_aux", "pcie_phy", "pcie_bus"; + <&clk IMX8MQ_CLK_PCIE2_AUX>; epdev_on-supply = <®_vcc_3v3>; hard-wired = <1>; status = "okay"; diff --git a/arch/arm64/boot/dts/freescale/imx8mq-tqma8mq.dtsi b/arch/arm64/boot/dts/freescale/imx8mq-tqma8mq.dtsi index 9a95e30fb42d..5ca6b2252546 100644 --- a/arch/arm64/boot/dts/freescale/imx8mq-tqma8mq.dtsi +++ b/arch/arm64/boot/dts/freescale/imx8mq-tqma8mq.dtsi @@ -194,8 +194,8 @@ }; }; - sensor0: temperature-sensor-eeprom@1b { - compatible = "nxp,se97", "jedec,jc-42.4-temp"; + sensor0: temperature-sensor@1b { + compatible = "nxp,se97b", "jedec,jc-42.4-temp"; reg = <0x1b>; }; diff --git a/arch/arm64/boot/dts/freescale/imx8mq-zii-ultra.dtsi b/arch/arm64/boot/dts/freescale/imx8mq-zii-ultra.dtsi index 4e05120c62d4..3a52679ecd68 100644 --- a/arch/arm64/boot/dts/freescale/imx8mq-zii-ultra.dtsi +++ b/arch/arm64/boot/dts/freescale/imx8mq-zii-ultra.dtsi @@ -490,7 +490,7 @@ pinctrl-0 = <&pinctrl_uart2>; status = "okay"; - rave-sp { + mcu { compatible = "zii,rave-sp-rdu2"; current-speed = <1000000>; #address-cells = <1>; @@ -551,10 +551,9 @@ pinctrl-0 = <&pinctrl_pcie0>; reset-gpio = <&gpio1 3 GPIO_ACTIVE_LOW>; clocks = <&clk IMX8MQ_CLK_PCIE1_ROOT>, - <&clk IMX8MQ_CLK_PCIE1_AUX>, + <&pcie0_refclk>, <&clk IMX8MQ_CLK_PCIE1_PHY>, - <&pcie0_refclk>; - clock-names = "pcie", "pcie_aux", "pcie_phy", "pcie_bus"; + <&clk IMX8MQ_CLK_PCIE1_AUX>; vph-supply = <&vgen5_reg>; status = "okay"; }; @@ -564,10 +563,9 @@ pinctrl-0 = <&pinctrl_pcie1>; reset-gpio = <&gpio1 6 GPIO_ACTIVE_LOW>; clocks = <&clk IMX8MQ_CLK_PCIE2_ROOT>, - <&clk IMX8MQ_CLK_PCIE2_AUX>, + <&pcie1_refclk>, <&clk IMX8MQ_CLK_PCIE2_PHY>, - <&pcie1_refclk>; - clock-names = "pcie", "pcie_aux", "pcie_phy", "pcie_bus"; + <&clk IMX8MQ_CLK_PCIE2_AUX>; vph-supply = <&vgen5_reg>; status = "okay"; }; diff --git a/arch/arm64/boot/dts/freescale/imx8mq.dtsi b/arch/arm64/boot/dts/freescale/imx8mq.dtsi index 7ce99c084e54..98fbba4c99a9 100644 --- a/arch/arm64/boot/dts/freescale/imx8mq.dtsi +++ b/arch/arm64/boot/dts/freescale/imx8mq.dtsi @@ -575,8 +575,7 @@ }; iomuxc_gpr: syscon@30340000 { - compatible = "fsl,imx8mq-iomuxc-gpr", "fsl,imx6q-iomuxc-gpr", - "syscon", "simple-mfd"; + compatible = "fsl,imx8mq-iomuxc-gpr", "syscon", "simple-mfd"; reg = <0x30340000 0x10000>; mux: mux-controller { @@ -593,15 +592,28 @@ #address-cells = <1>; #size-cells = <1>; - imx8mq_uid: soc-uid@410 { + /* + * The register address below maps to the MX8M + * Fusemap Description Table entries this way. + * Assuming + * reg = <ADDR SIZE>; + * then + * Fuse Address = (ADDR * 4) + 0x400 + * Note that if SIZE is greater than 4, then + * each subsequent fuse is located at offset + * +0x10 in Fusemap Description Table (e.g. + * reg = <0x4 0x8> describes fuses 0x410 and + * 0x420). + */ + imx8mq_uid: soc-uid@4 { /* 0x410-0x420 */ reg = <0x4 0x8>; }; - cpu_speed_grade: speed-grade@10 { + cpu_speed_grade: speed-grade@10 { /* 0x440 */ reg = <0x10 4>; }; - fec_mac_address: mac-address@90 { + fec_mac_address: mac-address@90 { /* 0x640 */ reg = <0x90 6>; }; }; @@ -1530,6 +1542,11 @@ <0 0 0 4 &gic GIC_SPI 122 IRQ_TYPE_LEVEL_HIGH>; fsl,max-link-speed = <2>; linux,pci-domain = <0>; + clocks = <&clk IMX8MQ_CLK_PCIE1_ROOT>, + <&clk IMX8MQ_CLK_PCIE1_PHY>, + <&clk IMX8MQ_CLK_PCIE1_PHY>, + <&clk IMX8MQ_CLK_PCIE1_AUX>; + clock-names = "pcie", "pcie_bus", "pcie_phy", "pcie_aux"; power-domains = <&pgc_pcie>; resets = <&src IMX8MQ_RESET_PCIEPHY>, <&src IMX8MQ_RESET_PCIE_CTRL_APPS_EN>, @@ -1567,6 +1584,11 @@ <0 0 0 4 &gic GIC_SPI 74 IRQ_TYPE_LEVEL_HIGH>; fsl,max-link-speed = <2>; linux,pci-domain = <1>; + clocks = <&clk IMX8MQ_CLK_PCIE2_ROOT>, + <&clk IMX8MQ_CLK_PCIE2_PHY>, + <&clk IMX8MQ_CLK_PCIE2_PHY>, + <&clk IMX8MQ_CLK_PCIE2_AUX>; + clock-names = "pcie", "pcie_bus", "pcie_phy", "pcie_aux"; power-domains = <&pgc_pcie>; resets = <&src IMX8MQ_RESET_PCIEPHY2>, <&src IMX8MQ_RESET_PCIE2_CTRL_APPS_EN>, diff --git a/arch/arm64/boot/dts/freescale/imx93-11x11-evk.dts b/arch/arm64/boot/dts/freescale/imx93-11x11-evk.dts index 27f9a9f33134..c928b6824e41 100644 --- a/arch/arm64/boot/dts/freescale/imx93-11x11-evk.dts +++ b/arch/arm64/boot/dts/freescale/imx93-11x11-evk.dts @@ -15,6 +15,13 @@ stdout-path = &lpuart1; }; + reg_vref_1v8: regulator-adc-vref { + compatible = "regulator-fixed"; + regulator-name = "vref_1v8"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + }; + reg_usdhc2_vmmc: regulator-usdhc2 { compatible = "regulator-fixed"; pinctrl-names = "default"; @@ -27,6 +34,11 @@ }; }; +&adc1 { + vref-supply = <®_vref_1v8>; + status = "okay"; +}; + &mu1 { status = "okay"; }; diff --git a/arch/arm64/boot/dts/freescale/imx93.dtsi b/arch/arm64/boot/dts/freescale/imx93.dtsi index 5d79663b3b84..abb3fbe4ba22 100644 --- a/arch/arm64/boot/dts/freescale/imx93.dtsi +++ b/arch/arm64/boot/dts/freescale/imx93.dtsi @@ -223,6 +223,20 @@ status = "disabled"; }; + flexcan1: can@443a0000 { + compatible = "fsl,imx93-flexcan"; + reg = <0x443a0000 0x10000>; + interrupts = <GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&clk IMX93_CLK_BUS_AON>, + <&clk IMX93_CLK_CAN1_GATE>; + clock-names = "ipg", "per"; + assigned-clocks = <&clk IMX93_CLK_CAN1>; + assigned-clock-parents = <&clk IMX93_CLK_SYS_PLL_PFD1_DIV2>; + assigned-clock-rates = <40000000>; + fsl,clk-source = /bits/ 8 <0>; + status = "disabled"; + }; + iomuxc: pinctrl@443c0000 { compatible = "fsl,imx93-iomuxc"; reg = <0x443c0000 0x10000>; @@ -266,6 +280,19 @@ compatible = "fsl,imx93-anatop", "syscon"; reg = <0x44480000 0x10000>; }; + + adc1: adc@44530000 { + compatible = "nxp,imx93-adc"; + reg = <0x44530000 0x10000>; + interrupts = <GIC_SPI 217 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 218 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 219 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 268 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&clk IMX93_CLK_ADC1_GATE>; + clock-names = "ipg"; + #io-channel-cells = <1>; + status = "disabled"; + }; }; aips2: bus@42000000 { @@ -393,6 +420,20 @@ status = "disabled"; }; + flexcan2: can@425b0000 { + compatible = "fsl,imx93-flexcan"; + reg = <0x425b0000 0x10000>; + interrupts = <GIC_SPI 51 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&clk IMX93_CLK_BUS_WAKEUP>, + <&clk IMX93_CLK_CAN2_GATE>; + clock-names = "ipg", "per"; + assigned-clocks = <&clk IMX93_CLK_CAN2>; + assigned-clock-parents = <&clk IMX93_CLK_SYS_PLL_PFD1_DIV2>; + assigned-clock-rates = <40000000>; + fsl,clk-source = /bits/ 8 <0>; + status = "disabled"; + }; + lpuart7: serial@42690000 { compatible = "fsl,imx93-lpuart", "fsl,imx7ulp-lpuart"; reg = <0x42690000 0x1000>; diff --git a/arch/arm64/boot/dts/freescale/mba8mx.dtsi b/arch/arm64/boot/dts/freescale/mba8mx.dtsi index daa37adeff3b..8a9fe5cdcc98 100644 --- a/arch/arm64/boot/dts/freescale/mba8mx.dtsi +++ b/arch/arm64/boot/dts/freescale/mba8mx.dtsi @@ -206,8 +206,8 @@ ldoin-supply = <®_vcc_3v3>; }; - sensor1: sensor@1f { - compatible = "nxp,se97", "jedec,jc-42.4-temp"; + sensor1: temperator-sensor@1f { + compatible = "nxp,se97b", "jedec,jc-42.4-temp"; reg = <0x1f>; }; |