arm64: dts: cn913x: add device trees for topology B boards

The CN913x DB with topology B is similar to a regular setup (A)
boards, but uses NAND flash as a boot device, while topology A
boards are booting from SPI flash.
Since NAND and SPI on CN913x DB boards share some wires, they
cannot be activated simultaneously.
The DTS files for setup "B" are based on setup "A", in which the
CP0 NAND controller enabled and CP0 SPI1 disabled.

Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>

1 files changed, 6 insertions, 397 deletions

diff --git a/arch/arm64/boot/dts/marvell/cn9130-db.dts b/arch/arm64/boot/dts/marvell/cn9130-db.dts
index 9758609541c7..994f347f2973 100644
--- a/arch/arm64/boot/dts/marvell/cn9130-db.dts
+++ b/arch/arm64/boot/dts/marvell/cn9130-db.dts
@@ -5,409 +5,18 @@
  * Device tree for the CN9130-DB board.
  */
 
-#include "cn9130.dtsi"
-
-#include <dt-bindings/gpio/gpio.h>
+#include "cn9130-db.dtsi"
 
 / {
-	model = "Marvell Armada CN9130-DB";
-
-	chosen {
-		stdout-path = "serial0:115200n8";
-	};
-
-	aliases {
-		gpio1 = &cp0_gpio1;
-		gpio2 = &cp0_gpio2;
-		i2c0 = &cp0_i2c0;
-		ethernet0 = &cp0_eth0;
-		ethernet1 = &cp0_eth1;
-		ethernet2 = &cp0_eth2;
-		spi1 = &cp0_spi0;
-		spi2 = &cp0_spi1;
-	};
-
-	memory@00000000 {
-		device_type = "memory";
-		reg = <0x0 0x0 0x0 0x80000000>;
-	};
-
-	ap0_reg_sd_vccq: ap0_sd_vccq@0 {
-		compatible = "regulator-gpio";
-		regulator-name = "ap0_sd_vccq";
-		regulator-min-microvolt = <1800000>;
-		regulator-max-microvolt = <3300000>;
-		gpios = <&expander0 8 GPIO_ACTIVE_HIGH>;
-		states = <1800000 0x1 3300000 0x0>;
-	};
-
-	cp0_reg_usb3_vbus0: cp0_usb3_vbus@0 {
-		compatible = "regulator-fixed";
-		regulator-name = "cp0-xhci0-vbus";
-		regulator-min-microvolt = <5000000>;
-		regulator-max-microvolt = <5000000>;
-		enable-active-high;
-		gpio = <&expander0 0 GPIO_ACTIVE_HIGH>;
-	};
-
-	cp0_usb3_0_phy0: cp0_usb3_phy@0 {
-		compatible = "usb-nop-xceiv";
-		vcc-supply = <&cp0_reg_usb3_vbus0>;
-	};
-
-	cp0_reg_usb3_vbus1: cp0_usb3_vbus@1 {
-		compatible = "regulator-fixed";
-		regulator-name = "cp0-xhci1-vbus";
-		regulator-min-microvolt = <5000000>;
-		regulator-max-microvolt = <5000000>;
-		enable-active-high;
-		gpio = <&expander0 1 GPIO_ACTIVE_HIGH>;
-	};
-
-	cp0_usb3_0_phy1: cp0_usb3_phy@1 {
-		compatible = "usb-nop-xceiv";
-		vcc-supply = <&cp0_reg_usb3_vbus1>;
-	};
-
-	cp0_reg_sd_vccq: cp0_sd_vccq@0 {
-		compatible = "regulator-gpio";
-		regulator-name = "cp0_sd_vccq";
-		regulator-min-microvolt = <1800000>;
-		regulator-max-microvolt = <3300000>;
-		gpios = <&expander0 15 GPIO_ACTIVE_HIGH>;
-		states = <1800000 0x1
-			  3300000 0x0>;
-	};
-
-	cp0_reg_sd_vcc: cp0_sd_vcc@0 {
-		compatible = "regulator-fixed";
-		regulator-name = "cp0_sd_vcc";
-		regulator-min-microvolt = <3300000>;
-		regulator-max-microvolt = <3300000>;
-		gpio = <&expander0 14 GPIO_ACTIVE_HIGH>;
-		enable-active-high;
-		regulator-always-on;
-	};
-
-	cp0_sfp_eth0: sfp-eth@0 {
-		compatible = "sff,sfp";
-		i2c-bus = <&cp0_sfpp0_i2c>;
-		los-gpio = <&cp0_module_expander1 11 GPIO_ACTIVE_HIGH>;
-		mod-def0-gpio = <&cp0_module_expander1 10 GPIO_ACTIVE_LOW>;
-		tx-disable-gpio = <&cp0_module_expander1 9 GPIO_ACTIVE_HIGH>;
-		tx-fault-gpio = <&cp0_module_expander1 8 GPIO_ACTIVE_HIGH>;
-		/*
-		 * SFP cages are unconnected on early PCBs because of an the I2C
-		 * lanes not being connected. Prevent the port for being
-		 * unusable by disabling the SFP node.
-		 */
-		status = "disabled";
-	};
-};
-
-&uart0 {
-	status = "okay";
-};
-
-/* on-board eMMC - U9 */
-&ap_sdhci0 {
-	pinctrl-names = "default";
-	bus-width = <8>;
-	mmc-ddr-1_8v;
-	mmc-hs400-1_8v;
-	vqmmc-supply = <&ap0_reg_sd_vccq>;
-	status = "okay";
-};
-
-&cp0_crypto {
-	status = "disabled";
-};
-
-&cp0_ethernet {
-	status = "okay";
-};
-
-/* SLM-1521-V2, CON9 */
-&cp0_eth0 {
-	status = "disabled";
-	phy-mode = "10gbase-kr";
-	/* Generic PHY, providing serdes lanes */
-	phys = <&cp0_comphy4 0>;
-	managed = "in-band-status";
-	sfp = <&cp0_sfp_eth0>;
-};
-
-/* CON56 */
-&cp0_eth1 {
-	status = "okay";
-	phy = <&phy0>;
-	phy-mode = "rgmii-id";
-};
-
-/* CON57 */
-&cp0_eth2 {
-	status = "okay";
-	phy = <&phy1>;
-	phy-mode = "rgmii-id";
-};
-
-&cp0_gpio1 {
-	status = "okay";
-};
-
-&cp0_gpio2 {
-	status = "okay";
-};
-
-&cp0_i2c0 {
-	status = "okay";
-	pinctrl-names = "default";
-	pinctrl-0 = <&cp0_i2c0_pins>;
-	clock-frequency = <100000>;
-
-	/* U36 */
-	expander0: pca953x@21 {
-		compatible = "nxp,pca9555";
-		pinctrl-names = "default";
-		gpio-controller;
-		#gpio-cells = <2>;
-		reg = <0x21>;
-		status = "okay";
-	};
-
-	/* U42 */
-	eeprom0: eeprom@50 {
-		compatible = "atmel,24c64";
-		reg = <0x50>;
-		pagesize = <0x20>;
-	};
-
-	/* U38 */
-	eeprom1: eeprom@57 {
-		compatible = "atmel,24c64";
-		reg = <0x57>;
-		pagesize = <0x20>;
-	};
-};
-
-&cp0_i2c1 {
-	status = "okay";
-	clock-frequency = <100000>;
-
-	/* SLM-1521-V2 - U3 */
-	i2c-mux@72 { /* verify address - depends on dpr */
-		compatible = "nxp,pca9544";
-		#address-cells = <1>;
-		#size-cells = <0>;
-		reg = <0x72>;
-		cp0_sfpp0_i2c: i2c@0 {
-			#address-cells = <1>;
-			#size-cells = <0>;
-			reg = <0>;
-		};
-
-		i2c@1 {
-			#address-cells = <1>;
-			#size-cells = <0>;
-			reg = <1>;
-			/* U12 */
-			cp0_module_expander1: pca9555@21 {
-				compatible = "nxp,pca9555";
-				pinctrl-names = "default";
-				gpio-controller;
-				#gpio-cells = <2>;
-				reg = <0x21>;
-			};
-
-		};
-	};
-};
-
-&cp0_mdio {
-	status = "okay";
-
-	phy0: ethernet-phy@0 {
-		reg = <0>;
-	};
-
-	phy1: ethernet-phy@1 {
-		reg = <1>;
-	};
-};
-
-/* U54 */
-&cp0_nand_controller {
-	pinctrl-names = "default";
-	pinctrl-0 = <&nand_pins &nand_rb>;
-
-	nand@0 {
-		reg = <0>;
-		label = "main-storage";
-		nand-rb = <0>;
-		nand-ecc-mode = "hw";
-		nand-on-flash-bbt;
-		nand-ecc-strength = <8>;
-		nand-ecc-step-size = <512>;
-
-		partitions {
-			compatible = "fixed-partitions";
-			#address-cells = <1>;
-			#size-cells = <1>;
-
-			partition@0 {
-				label = "U-Boot";
-				reg = <0 0x200000>;
-			};
-			partition@200000 {
-				label = "Linux";
-				reg = <0x200000 0xe00000>;
-			};
-			partition@1000000 {
-				label = "Filesystem";
-				reg = <0x1000000 0x3f000000>;
-			};
-		};
-	};
-};
-
-/* SLM-1521-V2, CON6 */
-&cp0_pcie0 {
-	status = "okay";
-	num-lanes = <4>;
-	num-viewport = <8>;
-	/* Generic PHY, providing serdes lanes */
-	phys = <&cp0_comphy0 0
-		&cp0_comphy1 0
-		&cp0_comphy2 0
-		&cp0_comphy3 0>;
-};
-
-&cp0_sata0 {
-	status = "okay";
-
-	/* SLM-1521-V2, CON2 */
-	sata-port@1 {
-		status = "okay";
-		/* Generic PHY, providing serdes lanes */
-		phys = <&cp0_comphy5 1>;
-	};
+	model = "Marvell Armada CN9130-DB setup A";
 };
 
-/* CON 28 */
-&cp0_sdhci0 {
-	status = "okay";
-	pinctrl-names = "default";
-	pinctrl-0 = <&cp0_sdhci_pins
-		     &cp0_sdhci_cd_pins>;
-	bus-width = <4>;
-	cd-gpios = <&cp0_gpio2 11 GPIO_ACTIVE_LOW>;
-	no-1-8-v;
-	vqmmc-supply = <&cp0_reg_sd_vccq>;
-	vmmc-supply = <&cp0_reg_sd_vcc>;
-};
+/* Setup A has SPI1 flash as a boot device, while setup B uses NAND flash.
+ * Since CP0 SPI1 and CP0 NAND are sharing some pins, they cannot be activated
+ * simultaneously. When SPI controller is enabled, NAND should be disabled.
+ */
 
-/* U55 */
 &cp0_spi1 {
 	status = "okay";
-	pinctrl-names = "default";
-	pinctrl-0 = <&cp0_spi0_pins>;
-	reg = <0x700680 0x50>;
-
-	spi-flash@0 {
-		#address-cells = <0x1>;
-		#size-cells = <0x1>;
-		compatible = "jedec,spi-nor";
-		reg = <0x0>;
-		/* On-board MUX does not allow higher frequencies */
-		spi-max-frequency = <40000000>;
-
-		partitions {
-			compatible = "fixed-partitions";
-			#address-cells = <1>;
-			#size-cells = <1>;
-
-			partition@0 {
-				label = "U-Boot-0";
-				reg = <0x0 0x200000>;
-			};
-
-			partition@400000 {
-				label = "Filesystem-0";
-				reg = <0x200000 0xe00000>;
-			};
-		};
-	};
 };
 
-&cp0_syscon0 {
-	cp0_pinctrl: pinctrl {
-		compatible = "marvell,cp115-standalone-pinctrl";
-
-		cp0_i2c0_pins: cp0-i2c-pins-0 {
-			marvell,pins = "mpp37", "mpp38";
-			marvell,function = "i2c0";
-		};
-		cp0_i2c1_pins: cp0-i2c-pins-1 {
-			marvell,pins = "mpp35", "mpp36";
-			marvell,function = "i2c1";
-		};
-		cp0_ge1_rgmii_pins: cp0-ge-rgmii-pins-0 {
-			marvell,pins = "mpp0", "mpp1", "mpp2",
-				       "mpp3", "mpp4", "mpp5",
-				       "mpp6", "mpp7", "mpp8",
-				       "mpp9", "mpp10", "mpp11";
-			marvell,function = "ge0";
-		};
-		cp0_ge2_rgmii_pins: cp0-ge-rgmii-pins-1 {
-			marvell,pins = "mpp44", "mpp45", "mpp46",
-				       "mpp47", "mpp48", "mpp49",
-				       "mpp50", "mpp51", "mpp52",
-				       "mpp53", "mpp54", "mpp55";
-			marvell,function = "ge1";
-		};
-		cp0_sdhci_cd_pins: cp0-sdhci-cd-pins-0 {
-			marvell,pins = "mpp43";
-			marvell,function = "gpio";
-		};
-		cp0_sdhci_pins: cp0-sdhi-pins-0 {
-			marvell,pins = "mpp56", "mpp57", "mpp58",
-				       "mpp59", "mpp60", "mpp61";
-			marvell,function = "sdio";
-		};
-		cp0_spi0_pins: cp0-spi-pins-0 {
-			marvell,pins = "mpp13", "mpp14", "mpp15", "mpp16";
-			marvell,function = "spi1";
-		};
-		nand_pins: nand-pins {
-			marvell,pins = "mpp15", "mpp16", "mpp17", "mpp18",
-				       "mpp19", "mpp20", "mpp21", "mpp22",
-				       "mpp23", "mpp24", "mpp25", "mpp26",
-				       "mpp27";
-			marvell,function = "dev";
-		};
-		nand_rb: nand-rb {
-			marvell,pins = "mpp13";
-			marvell,function = "nf";
-		};
-	};
-};
-
-&cp0_utmi {
-	status = "okay";
-};
-
-&cp0_usb3_0 {
-	status = "okay";
-	usb-phy = <&cp0_usb3_0_phy0>;
-	phys = <&cp0_utmi0>;
-	phy-names = "utmi";
-	dr_mode = "host";
-};
-
-&cp0_usb3_1 {
-	status = "okay";
-	usb-phy = <&cp0_usb3_0_phy1>;
-	phys =  <&cp0_utmi1>;
-	phy-names = "utmi";
-	dr_mode = "host";
-};