arm64: dts: cn913x: add device trees for topology B boards

The CN913x DB with topology B is similar to a regular setup (A)
boards, but uses NAND flash as a boot device, while topology A
boards are booting from SPI flash.
Since NAND and SPI on CN913x DB boards share some wires, they
cannot be activated simultaneously.
The DTS files for setup "B" are based on setup "A", in which the
CP0 NAND controller enabled and CP0 SPI1 disabled.

Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>

1 files changed, 6 insertions, 191 deletions

diff --git a/arch/arm64/boot/dts/marvell/cn9131-db.dts b/arch/arm64/boot/dts/marvell/cn9131-db.dts
index ba2d4e1da159..a60fdee79bf8 100644
--- a/arch/arm64/boot/dts/marvell/cn9131-db.dts
+++ b/arch/arm64/boot/dts/marvell/cn9131-db.dts
@@ -5,203 +5,18 @@
  * Device tree for the CN9131-DB board.
  */
 
-#include "cn9130-db.dts"
+#include "cn9131-db.dtsi"
 
 / {
-	model = "Marvell Armada CN9131-DB";
-	compatible = "marvell,cn9131", "marvell,cn9130",
-		     "marvell,armada-ap807-quad", "marvell,armada-ap807";
-
-	aliases {
-		gpio3 = &cp1_gpio1;
-		gpio4 = &cp1_gpio2;
-		ethernet3 = &cp1_eth0;
-		ethernet4 = &cp1_eth1;
-	};
-
-	cp1_reg_usb3_vbus0: cp1_usb3_vbus@0 {
-		compatible = "regulator-fixed";
-		pinctrl-names = "default";
-		pinctrl-0 = <&cp1_xhci0_vbus_pins>;
-		regulator-name = "cp1-xhci0-vbus";
-		regulator-min-microvolt = <5000000>;
-		regulator-max-microvolt = <5000000>;
-		enable-active-high;
-		gpio = <&cp1_gpio1 3 GPIO_ACTIVE_HIGH>;
-	};
-
-	cp1_usb3_0_phy0: cp1_usb3_phy0 {
-		compatible = "usb-nop-xceiv";
-		vcc-supply = <&cp1_reg_usb3_vbus0>;
-	};
-
-	cp1_sfp_eth1: sfp-eth1 {
-		compatible = "sff,sfp";
-		i2c-bus = <&cp1_i2c0>;
-		los-gpio = <&cp1_gpio1 11 GPIO_ACTIVE_HIGH>;
-		mod-def0-gpio = <&cp1_gpio1 10 GPIO_ACTIVE_LOW>;
-		tx-disable-gpio = <&cp1_gpio1 9 GPIO_ACTIVE_HIGH>;
-		tx-fault-gpio = <&cp1_gpio1 8 GPIO_ACTIVE_HIGH>;
-		pinctrl-names = "default";
-		pinctrl-0 = <&cp1_sfp_pins>;
-		/*
-		 * SFP cages are unconnected on early PCBs because of an the I2C
-		 * lanes not being connected. Prevent the port for being
-		 * unusable by disabling the SFP node.
-		 */
-		status = "disabled";
-	};
+	model = "Marvell Armada CN9131-DB setup A";
 };
 
-/*
- * Instantiate the first slave CP115
+/* Setup A has SPI1 flash as a boot device, while setup B uses NAND flash.
+ * Since CP0 SPI1 and CP0 NAND are sharing some pins, they cannot be activated
+ * simultaneously. When SPI controller is enabled, NAND should be disabled.
  */
 
-#define CP11X_NAME		cp1
-#define CP11X_BASE		f4000000
-#define CP11X_PCIEx_MEM_BASE(iface) (0xe2000000 + (iface * 0x1000000))
-#define CP11X_PCIEx_MEM_SIZE(iface) 0xf00000
-#define CP11X_PCIE0_BASE	f4600000
-#define CP11X_PCIE1_BASE	f4620000
-#define CP11X_PCIE2_BASE	f4640000
-
-#include "armada-cp115.dtsi"
-
-#undef CP11X_NAME
-#undef CP11X_BASE
-#undef CP11X_PCIEx_MEM_BASE
-#undef CP11X_PCIEx_MEM_SIZE
-#undef CP11X_PCIE0_BASE
-#undef CP11X_PCIE1_BASE
-#undef CP11X_PCIE2_BASE
-
-&cp1_crypto {
-	status = "disabled";
-};
-
-&cp1_ethernet {
-	status = "okay";
-};
-
-/* CON50 */
-&cp1_eth0 {
-	status = "disabled";
-	phy-mode = "10gbase-kr";
-	/* Generic PHY, providing serdes lanes */
-	phys = <&cp1_comphy4 0>;
-	managed = "in-band-status";
-	sfp = <&cp1_sfp_eth1>;
-};
-
-&cp1_gpio1 {
-	status = "okay";
-};
-
-&cp1_gpio2 {
-	status = "okay";
-};
-
-&cp1_i2c0 {
-	status = "okay";
-	pinctrl-names = "default";
-	pinctrl-0 = <&cp1_i2c0_pins>;
-	clock-frequency = <100000>;
-};
-
-/* CON40 */
-&cp1_pcie0 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&cp1_pcie_reset_pins>;
-	num-lanes = <2>;
-	num-viewport = <8>;
-	marvell,reset-gpio = <&cp1_gpio1 0 GPIO_ACTIVE_HIGH>;
-	status = "okay";
-	/* Generic PHY, providing serdes lanes */
-	phys = <&cp1_comphy0 0
-		&cp1_comphy1 0>;
-};
-
-&cp1_sata0 {
-	status = "okay";
-
-	/* CON32 */
-	sata-port@1 {
-		/* Generic PHY, providing serdes lanes */
-		phys = <&cp1_comphy5 1>;
-	};
-};
-
-/* U24 */
-&cp1_spi1 {
-	status = "okay";
-	pinctrl-names = "default";
-	pinctrl-0 = <&cp1_spi0_pins>;
-	reg = <0x700680 0x50>;
-
-	spi-flash@0 {
-		#address-cells = <0x1>;
-		#size-cells = <0x1>;
-		compatible = "jedec,spi-nor";
-		reg = <0x0>;
-		/* On-board MUX does not allow higher frequencies */
-		spi-max-frequency = <40000000>;
-
-		partitions {
-			compatible = "fixed-partitions";
-			#address-cells = <1>;
-			#size-cells = <1>;
-
-			partition@0 {
-				label = "U-Boot-1";
-				reg = <0x0 0x200000>;
-			};
-
-			partition@400000 {
-				label = "Filesystem-1";
-				reg = <0x200000 0xe00000>;
-			};
-		};
-	};
-
-};
-
-&cp1_syscon0 {
-	cp1_pinctrl: pinctrl {
-		compatible = "marvell,cp115-standalone-pinctrl";
-
-		cp1_i2c0_pins: cp1-i2c-pins-0 {
-			marvell,pins = "mpp37", "mpp38";
-			marvell,function = "i2c0";
-		};
-		cp1_spi0_pins: cp1-spi-pins-0 {
-			marvell,pins = "mpp13", "mpp14", "mpp15", "mpp16";
-			marvell,function = "spi1";
-		};
-		cp1_xhci0_vbus_pins: cp1-xhci0-vbus-pins {
-			marvell,pins = "mpp3";
-			marvell,function = "gpio";
-		};
-		cp1_sfp_pins: sfp-pins {
-			marvell,pins = "mpp8", "mpp9", "mpp10", "mpp11";
-			marvell,function = "gpio";
-		};
-		cp1_pcie_reset_pins: cp1-pcie-reset-pins {
-			marvell,pins = "mpp0";
-			marvell,function = "gpio";
-		};
-	};
-};
-
-/* CON58 */
-&cp1_utmi {
+&cp0_spi1 {
 	status = "okay";
 };
 
-&cp1_usb3_1 {
-	status = "okay";
-	usb-phy = <&cp1_usb3_0_phy0>;
-	/* Generic PHY, providing serdes lanes */
-	phys = <&cp1_comphy3 1>, <&cp1_utmi1>;
-	phy-names = "usb", "utmi";
-	dr_mode = "host";
-};