Merge tag 'dt-5.16' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc

Pull ARM SoC DT updates from Arnd Bergmann:
 "This is a rather large update for the ARM devicetree files, after a
  few quieter releases, with 775 total commits and 47 branches pulled
  into this one.

  There are 5 new SoC types plus some minor variations, and a total of
  60 new machines, so I'm limiting the summary to the main noteworthy
  items:

   - Apple M1 gain support for PCI and pinctrl, getting a bit closer to
     a usable system out of the box.

   - Qualcomm gains support for Snapdragon 690 (aka SM6350) as well as
     SM7225, 11 new smartphones, and three additional Chromebooks, and
     improvements all over the place.

   - Samsung gains support for ExynosAutov9, an automotive version of
     their smartphone SoC, but otherwise no major changes.

   - Microchip adds the SAMA5D29 SoC in the SAMA5 family, and a number
     of improvements for the recently added SAMA7 family. The LAN966 SoC
     that was added in the platform code does not have dts files yet.
     Two board files are added for the older at91sam9g20 SoC

   - Aspeed supports two additional server boards using their AST2600 as
     BMC, and improves support for qemu models

   - Rockchip RK3566/RK3688 gets added, along with six new development
     boards using RK3328/RK3399/RK3566, and one Chromebook tablet.

   - Two NAS boxes are added using the ARMv4 based Gemini platform

   - One new board is added to the Intel Arria SoC FPGA family

   - Marvell adds one network switch based on Armada 381 and the new
     MOCHAbin 7040 development board

   - NXP adds support for the S32G2 automotive SoC, two imx6 based ebook
     readers, and three additional development boards, which is notably
     less than their usual additions, but they also gain improvements to
     their many existing boards

   - STmicroelectronics adds their stm32mp13 SoC family along with a
     reference board

   - Renesas adds new versions of their R-Car Gen3 SoCs and many updates
     for their older generations

   - Broadcom adds support for a number of Cisco Meraki wireless
     controllers, along with two new boards and other updates for
     BCM53xx/BCM47xx networking SoCs and the Raspberry Pi boards

   - Mediatek improves support for the MT81xx SoCs used in Chromebooks
     as well as the MT76xx networking SoCs

   - NVIDIA adds a number of cleanups and additional support for more
     hardware on the already supported machines

   - TI K3 adds support for three new boards along with cleanups

   - Toshiba adds one board for the Visconti family

   - Xilinx adds five new ZynqMP based machines

   - Amlogic support is added for the Radxa Zero and two Jethub home
     automation controllers, along with changes to other machines

   - Rob Herring continues his work on fixing dtc warnings all over the
     tree.

   - Minor updates for TI OMAP, Mstar, Allwinner/sunxi, Hisilicon,
     Ux500, Unisoc"

* tag 'dt-5.16' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (720 commits)
  arm64: dts: apple: j274: Expose PCI node for the Ethernet MAC address
  arm64: dts: apple: t8103: Add root port interrupt routing
  arm64: dts: apple: t8103: Add PCIe DARTs
  arm64: apple: Add PCIe node
  arm64: apple: Add pinctrl nodes
  ARM: dts: arm: Update ICST clock nodes 'reg' and node names
  ARM: dts: arm: Update register-bit-led nodes 'reg' and node names
  arm64: dts: exynos: add chipid node for exynosautov9 SoC
  ARM: dts: qcom: fix typo in IPQ8064 thermal-sensor node
  Revert "arm64: dts: qcom: msm8916-asus-z00l: Add sensors"
  arm64: dts: qcom: ipq6018: Remove unused 'iface_clk' property from dma-controller node
  arm64: dts: qcom: ipq6018: Remove unused 'qcom,config-pipe-trust-reg' property
  arm64: dts: qcom: sm8350: Add CPU topology and idle-states
  arm64: dts: qcom: Drop unneeded extra device-specific includes
  arm64: dts: qcom: msm8916: Drop standalone smem node
  arm64: dts: qcom: Fix node name of rpm-msg-ram device nodes
  arm64: dts: qcom: msm8916-asus-z00l: Add sensors
  arm64: dts: qcom: msm8916-asus-z00l: Add SDCard
  arm64: dts: qcom: msm8916-asus-z00l: Add touchscreen
  arm64: dts: qcom: sdm845-oneplus: remove devinfo-size from ramoops node
  ...

361 files changed, 37780 insertions, 5380 deletions

diff --git a/arch/arm64/boot/dts/allwinner/axp803.dtsi b/arch/arm64/boot/dts/allwinner/axp803.dtsi
index 10e9186a76bf..578ef368e2b4 100644
--- a/arch/arm64/boot/dts/allwinner/axp803.dtsi
+++ b/arch/arm64/boot/dts/allwinner/axp803.dtsi
@@ -10,7 +10,7 @@
 	interrupt-controller;
 	#interrupt-cells = <1>;
 
-	ac_power_supply: ac-power-supply {
+	ac_power_supply: ac-power {
 		compatible = "x-powers,axp803-ac-power-supply",
 			     "x-powers,axp813-ac-power-supply";
 		status = "disabled";
@@ -26,18 +26,18 @@
 		gpio-controller;
 		#gpio-cells = <2>;
 
-		gpio0_ldo: gpio0-ldo {
+		gpio0_ldo: gpio0-ldo-pin {
 			pins = "GPIO0";
 			function = "ldo";
 		};
 
-		gpio1_ldo: gpio1-ldo {
+		gpio1_ldo: gpio1-ldo-pin {
 			pins = "GPIO1";
 			function = "ldo";
 		};
 	};
 
-	battery_power_supply: battery-power-supply {
+	battery_power_supply: battery-power {
 		compatible = "x-powers,axp803-battery-power-supply",
 			     "x-powers,axp813-battery-power-supply";
 		status = "disabled";
@@ -147,7 +147,7 @@
 		};
 	};
 
-	usb_power_supply: usb-power-supply {
+	usb_power_supply: usb-power {
 		compatible = "x-powers,axp803-usb-power-supply",
 			     "x-powers,axp813-usb-power-supply";
 		status = "disabled";
diff --git a/arch/arm64/boot/dts/allwinner/sun50i-a100.dtsi b/arch/arm64/boot/dts/allwinner/sun50i-a100.dtsi
index cc321c04f121..f6d7d7f7fdab 100644
--- a/arch/arm64/boot/dts/allwinner/sun50i-a100.dtsi
+++ b/arch/arm64/boot/dts/allwinner/sun50i-a100.dtsi
@@ -343,19 +343,19 @@
 	};
 
 	thermal-zones {
-		cpu-thermal-zone {
+		cpu-thermal {
 			polling-delay-passive = <0>;
 			polling-delay = <0>;
 			thermal-sensors = <&ths 0>;
 		};
 
-		ddr-thermal-zone {
+		ddr-thermal {
 			polling-delay-passive = <0>;
 			polling-delay = <0>;
 			thermal-sensors = <&ths 2>;
 		};
 
-		gpu-thermal-zone {
+		gpu-thermal {
 			polling-delay-passive = <0>;
 			polling-delay = <0>;
 			thermal-sensors = <&ths 1>;
diff --git a/arch/arm64/boot/dts/allwinner/sun50i-a64-cpu-opp.dtsi b/arch/arm64/boot/dts/allwinner/sun50i-a64-cpu-opp.dtsi
index 578c37490d90..e39db51eb448 100644
--- a/arch/arm64/boot/dts/allwinner/sun50i-a64-cpu-opp.dtsi
+++ b/arch/arm64/boot/dts/allwinner/sun50i-a64-cpu-opp.dtsi
@@ -4,7 +4,7 @@
  */
 
 / {
-	cpu0_opp_table: opp_table0 {
+	cpu0_opp_table: opp-table-cpu {
 		compatible = "operating-points-v2";
 		opp-shared;
 
diff --git a/arch/arm64/boot/dts/allwinner/sun50i-a64-orangepi-win.dts b/arch/arm64/boot/dts/allwinner/sun50i-a64-orangepi-win.dts
index 097a5511523a..c519d9fa6967 100644
--- a/arch/arm64/boot/dts/allwinner/sun50i-a64-orangepi-win.dts
+++ b/arch/arm64/boot/dts/allwinner/sun50i-a64-orangepi-win.dts
@@ -343,7 +343,7 @@
 &spi0 {
 	status = "okay";
 
-	spi-flash@0 {
+	flash@0 {
 		compatible = "mxicy,mx25l1606e", "jedec,spi-nor";
 		reg = <0>;
 		spi-max-frequency = <80000000>;
diff --git a/arch/arm64/boot/dts/allwinner/sun50i-a64-pinetab.dts b/arch/arm64/boot/dts/allwinner/sun50i-a64-pinetab.dts
index 7ef96f9ff7ae..adb0b28b06d8 100644
--- a/arch/arm64/boot/dts/allwinner/sun50i-a64-pinetab.dts
+++ b/arch/arm64/boot/dts/allwinner/sun50i-a64-pinetab.dts
@@ -35,6 +35,17 @@
 		stdout-path = "serial0:115200n8";
 	};
 
+	hdmi-connector {
+		compatible = "hdmi-connector";
+		type = "c";
+
+		port {
+			hdmi_con_in: endpoint {
+				remote-endpoint = <&hdmi_out_con>;
+			};
+		};
+	};
+
 	i2c-csi {
 		compatible = "i2c-gpio";
 		sda-gpios = <&pio 4 13 GPIO_ACTIVE_HIGH>; /* PE13 */
@@ -77,7 +88,7 @@
 		sound-name-prefix = "Speaker Amp";
 	};
 
-	vdd_bl: regulator@0 {
+	vdd_bl: regulator {
 		compatible = "regulator-fixed";
 		regulator-name = "bl-3v3";
 		regulator-min-microvolt = <3300000>;
@@ -410,6 +421,21 @@
 	regulator-name = "vcc-rtc";
 };
 
+&simplefb_hdmi {
+	vcc-hdmi-supply = <&reg_dldo1>;
+};
+
+&hdmi {
+	hvcc-supply = <&reg_dldo1>;
+	status = "okay";
+};
+
+&hdmi_out {
+	hdmi_out_con: endpoint {
+		remote-endpoint = <&hdmi_con_in>;
+	};
+};
+
 &sound {
 	status = "okay";
 	simple-audio-card,aux-devs = <&codec_analog>, <&speaker_amp>;
diff --git a/arch/arm64/boot/dts/allwinner/sun50i-a64-teres-i.dts b/arch/arm64/boot/dts/allwinner/sun50i-a64-teres-i.dts
index 45e1abdf70a0..aef571acd67f 100644
--- a/arch/arm64/boot/dts/allwinner/sun50i-a64-teres-i.dts
+++ b/arch/arm64/boot/dts/allwinner/sun50i-a64-teres-i.dts
@@ -139,6 +139,8 @@
 			#size-cells = <0>;
 
 			port@0 {
+				reg = <0>;
+
 				anx6345_in: endpoint {
 					remote-endpoint = <&tcon0_out_anx6345>;
 				};
@@ -206,7 +208,6 @@
 		reg = <0x3a3>;
 		interrupt-parent = <&r_intc>;
 		interrupts = <GIC_SPI 32 IRQ_TYPE_LEVEL_LOW>;
-		wakeup-source;
 	};
 };
 
diff --git a/arch/arm64/boot/dts/allwinner/sun50i-a64.dtsi b/arch/arm64/boot/dts/allwinner/sun50i-a64.dtsi
index 6ddb717f2f98..5ba379078500 100644
--- a/arch/arm64/boot/dts/allwinner/sun50i-a64.dtsi
+++ b/arch/arm64/boot/dts/allwinner/sun50i-a64.dtsi
@@ -102,6 +102,22 @@
 		status = "disabled";
 	};
 
+	gpu_opp_table: opp-table-gpu {
+		compatible = "operating-points-v2";
+
+		opp-120000000 {
+			opp-hz = /bits/ 64 <120000000>;
+		};
+
+		opp-312000000 {
+			opp-hz = /bits/ 64 <312000000>;
+		};
+
+		opp-432000000 {
+			opp-hz = /bits/ 64 <432000000>;
+		};
+	};
+
 	osc24M: osc24M_clk {
 		#clock-cells = <0>;
 		compatible = "fixed-clock";
@@ -1103,6 +1119,7 @@
 			clocks = <&ccu CLK_BUS_GPU>, <&ccu CLK_GPU>;
 			clock-names = "bus", "core";
 			resets = <&ccu RST_BUS_GPU>;
+			operating-points-v2 = <&gpu_opp_table>;
 		};
 
 		gic: interrupt-controller@1c81000 {
diff --git a/arch/arm64/boot/dts/allwinner/sun50i-h5-cpu-opp.dtsi b/arch/arm64/boot/dts/allwinner/sun50i-h5-cpu-opp.dtsi
index b2657201957e..1afad8b437d7 100644
--- a/arch/arm64/boot/dts/allwinner/sun50i-h5-cpu-opp.dtsi
+++ b/arch/arm64/boot/dts/allwinner/sun50i-h5-cpu-opp.dtsi
@@ -2,7 +2,7 @@
 // Copyright (C) 2020 Chen-Yu Tsai <wens@csie.org>
 
 / {
-	cpu_opp_table: cpu-opp-table {
+	cpu_opp_table: opp-table-cpu {
 		compatible = "operating-points-v2";
 		opp-shared;
 
diff --git a/arch/arm64/boot/dts/allwinner/sun50i-h5-nanopi-r1s-h5.dts b/arch/arm64/boot/dts/allwinner/sun50i-h5-nanopi-r1s-h5.dts
index 55bcdf8d1a07..55b369534a08 100644
--- a/arch/arm64/boot/dts/allwinner/sun50i-h5-nanopi-r1s-h5.dts
+++ b/arch/arm64/boot/dts/allwinner/sun50i-h5-nanopi-r1s-h5.dts
@@ -142,9 +142,16 @@
 	status = "okay";
 
 	eeprom@51 {
-		compatible = "microchip,24c02";
+		compatible = "microchip,24c02", "atmel,24c02";
 		reg = <0x51>;
 		pagesize = <16>;
+		read-only;
+		#address-cells = <1>;
+		#size-cells = <1>;
+
+		eth_mac1: mac-address@fa {
+			reg = <0xfa 0x06>;
+		};
 	};
 };
 
diff --git a/arch/arm64/boot/dts/allwinner/sun50i-h5.dtsi b/arch/arm64/boot/dts/allwinner/sun50i-h5.dtsi
index 578a63dedf46..9988e87ea7b3 100644
--- a/arch/arm64/boot/dts/allwinner/sun50i-h5.dtsi
+++ b/arch/arm64/boot/dts/allwinner/sun50i-h5.dtsi
@@ -217,7 +217,7 @@
 			};
 		};
 
-		gpu_thermal {
+		gpu-thermal {
 			polling-delay-passive = <0>;
 			polling-delay = <0>;
 			thermal-sensors = <&ths 1>;
diff --git a/arch/arm64/boot/dts/allwinner/sun50i-h6-cpu-opp.dtsi b/arch/arm64/boot/dts/allwinner/sun50i-h6-cpu-opp.dtsi
index 8c6e8536b69f..0baf0f8e4d27 100644
--- a/arch/arm64/boot/dts/allwinner/sun50i-h6-cpu-opp.dtsi
+++ b/arch/arm64/boot/dts/allwinner/sun50i-h6-cpu-opp.dtsi
@@ -3,7 +3,7 @@
 // Copyright (C) 2020 Clément Péron <peron.clem@gmail.com>
 
 / {
-	cpu_opp_table: cpu-opp-table {
+	cpu_opp_table: opp-table-cpu {
 		compatible = "allwinner,sun50i-h6-operating-points";
 		nvmem-cells = <&cpu_speed_grade>;
 		opp-shared;
diff --git a/arch/arm64/boot/dts/allwinner/sun50i-h6.dtsi b/arch/arm64/boot/dts/allwinner/sun50i-h6.dtsi
index 30d396e8c762..46ed529a4dc2 100644
--- a/arch/arm64/boot/dts/allwinner/sun50i-h6.dtsi
+++ b/arch/arm64/boot/dts/allwinner/sun50i-h6.dtsi
@@ -119,10 +119,10 @@
 			display_clocks: clock@0 {
 				compatible = "allwinner,sun50i-h6-de3-clk";
 				reg = <0x0 0x10000>;
-				clocks = <&ccu CLK_DE>,
-					 <&ccu CLK_BUS_DE>;
-				clock-names = "mod",
-					      "bus";
+				clocks = <&ccu CLK_BUS_DE>,
+					 <&ccu CLK_DE>;
+				clock-names = "bus",
+					      "mod";
 				resets = <&ccu RST_BUS_DE>;
 				#clock-cells = <1>;
 				#reset-cells = <1>;
diff --git a/arch/arm64/boot/dts/amlogic/Makefile b/arch/arm64/boot/dts/amlogic/Makefile
index faa0a79a34f5..5148cd9e5146 100644
--- a/arch/arm64/boot/dts/amlogic/Makefile
+++ b/arch/arm64/boot/dts/amlogic/Makefile
@@ -1,5 +1,7 @@
 # SPDX-License-Identifier: GPL-2.0
 dtb-$(CONFIG_ARCH_MESON) += meson-axg-s400.dtb
+dtb-$(CONFIG_ARCH_MESON) += meson-axg-jethome-jethub-j100.dtb
+dtb-$(CONFIG_ARCH_MESON) += meson-g12a-radxa-zero.dtb
 dtb-$(CONFIG_ARCH_MESON) += meson-g12a-sei510.dtb
 dtb-$(CONFIG_ARCH_MESON) += meson-g12a-u200.dtb
 dtb-$(CONFIG_ARCH_MESON) += meson-g12a-x96-max.dtb
@@ -38,6 +40,7 @@ dtb-$(CONFIG_ARCH_MESON) += meson-gxl-s805x-p241.dtb
 dtb-$(CONFIG_ARCH_MESON) += meson-gxl-s905w-p281.dtb
 dtb-$(CONFIG_ARCH_MESON) += meson-gxl-s905w-tx3-mini.dtb
 dtb-$(CONFIG_ARCH_MESON) += meson-gxl-s905d-libretech-pc.dtb
+dtb-$(CONFIG_ARCH_MESON) += meson-gxl-s905w-jethome-jethub-j80.dtb
 dtb-$(CONFIG_ARCH_MESON) += meson-gxm-khadas-vim2.dtb
 dtb-$(CONFIG_ARCH_MESON) += meson-gxm-mecool-kiii-pro.dtb
 dtb-$(CONFIG_ARCH_MESON) += meson-gxm-minix-neo-u9h.dtb
diff --git a/arch/arm64/boot/dts/amlogic/meson-axg-jethome-jethub-j100.dts b/arch/arm64/boot/dts/amlogic/meson-axg-jethome-jethub-j100.dts
new file mode 100644
index 000000000000..52ebe371df26
--- /dev/null
+++ b/arch/arm64/boot/dts/amlogic/meson-axg-jethome-jethub-j100.dts
@@ -0,0 +1,362 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright (c) 2021 Vyacheslav Bocharov <adeep@lexina.in>
+ * Copyright (c) 2020 JetHome
+ * Author: Aleksandr Kazantsev <ak@tvip.ru>
+ * Author: Alexey Shevelkin <ash@tvip.ru>
+ * Author: Vyacheslav Bocharov <adeep@lexina.in>
+ */
+
+/dts-v1/;
+
+#include "meson-axg.dtsi"
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/thermal/thermal.h>
+
+/ {
+	compatible = "jethome,jethub-j100", "amlogic,a113d", "amlogic,meson-axg";
+	model = "JetHome JetHub J100";
+	aliases {
+		serial0 = &uart_AO;   /* Console */
+		serial1 = &uart_AO_B; /* External UART (Wireless Module) */
+		ethernet0 = &ethmac;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	/* 1024MB RAM */
+	memory@0 {
+		device_type = "memory";
+		reg = <0x0 0x0 0x0 0x40000000>;
+	};
+
+	reserved-memory {
+		linux,cma {
+			size = <0x0 0x400000>;
+		};
+	};
+
+	emmc_pwrseq: emmc-pwrseq {
+		compatible = "mmc-pwrseq-emmc";
+		reset-gpios = <&gpio BOOT_9 GPIO_ACTIVE_LOW>;
+	};
+
+	vcc_3v3: regulator-vcc_3v3 {
+		compatible = "regulator-fixed";
+		regulator-name = "VCC_3V3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		vin-supply = <&vddao_3v3>;
+		regulator-always-on;
+	};
+
+	vcc_5v: regulator-vcc_5v {
+		compatible = "regulator-fixed";
+		regulator-name = "VCC5V";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		regulator-always-on;
+	};
+
+	vddao_3v3: regulator-vddao_3v3 {
+		compatible = "regulator-fixed";
+		regulator-name = "VDDAO_3V3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		vin-supply = <&vcc_5v>;
+		regulator-always-on;
+	};
+
+	vddio_ao18: regulator-vddio_ao18 {
+		compatible = "regulator-fixed";
+		regulator-name = "VDDIO_AO18";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+		vin-supply = <&vddao_3v3>;
+		regulator-always-on;
+	};
+
+	vddio_boot: regulator-vddio_boot {
+		compatible = "regulator-fixed";
+		regulator-name = "VDDIO_BOOT";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+		vin-supply = <&vddao_3v3>;
+		regulator-always-on;
+	};
+
+	usb_pwr: regulator-usb_pwr {
+		compatible = "regulator-fixed";
+		regulator-name = "USB_PWR";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		vin-supply = <&vcc_5v>;
+		regulator-always-on;
+	};
+
+	sdio_pwrseq: sdio-pwrseq {
+		compatible = "mmc-pwrseq-simple";
+		reset-gpios = <&gpio GPIOX_7 GPIO_ACTIVE_LOW>;
+		clocks = <&wifi32k>;
+		clock-names = "ext_clock";
+	};
+
+	wifi32k: wifi32k {
+		compatible = "pwm-clock";
+		#clock-cells = <0>;
+		clock-frequency = <32768>;
+		pwms = <&pwm_ab 0 30518 0>; /* PWM_A at 32.768KHz */
+	};
+
+	thermal-zones {
+		cpu_thermal: cpu-thermal {
+			polling-delay-passive = <250>;
+			polling-delay = <1000>;
+			thermal-sensors = <&scpi_sensors 0>;
+			trips {
+				cpu_passive: cpu-passive {
+					temperature = <70000>; /* millicelsius */
+					hysteresis = <2000>; /* millicelsius */
+					type = "passive";
+				};
+
+				cpu_hot: cpu-hot {
+					temperature = <80000>; /* millicelsius */
+					hysteresis = <2000>; /* millicelsius */
+					type = "hot";
+				};
+
+				cpu_critical: cpu-critical {
+					temperature = <100000>; /* millicelsius */
+					hysteresis = <2000>; /* millicelsius */
+					type = "critical";
+				};
+			};
+		};
+
+		cpu_cooling_maps: cooling-maps {
+			map0 {
+				trip = <&cpu_passive>;
+				cooling-device = <&cpu0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+						<&cpu1 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+						<&cpu2 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+						<&cpu3 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
+			};
+
+			map1 {
+				trip = <&cpu_hot>;
+				cooling-device = <&cpu0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+						<&cpu1 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+						<&cpu2 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+						<&cpu3 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
+			};
+		};
+	};
+
+	onewire {
+		compatible = "w1-gpio";
+		gpios = <&gpio GPIOA_14 GPIO_ACTIVE_HIGH>;
+		#gpio-cells = <1>;
+	};
+};
+
+&efuse {
+	sn: sn@32 {
+		reg = <0x32 0x20>;
+	};
+
+	eth_mac: eth_mac@0 {
+		reg = <0x0 0x6>;
+	};
+
+	bt_mac: bt_mac@6 {
+		reg = <0x6 0x6>;
+	};
+
+	wifi_mac: wifi_mac@c {
+		reg = <0xc 0x6>;
+	};
+
+	bid: bid@12 {
+		reg = <0x12 0x20>;
+	};
+};
+
+&ethmac {
+	status = "okay";
+	pinctrl-0 = <&eth_rmii_x_pins>;
+	pinctrl-names = "default";
+	phy-handle = <&eth_phy0>;
+	phy-mode = "rmii";
+
+	mdio {
+		compatible = "snps,dwmac-mdio";
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		/* ICPlus IP101A/G Ethernet PHY (vendor_id=0x0243, model_id=0x0c54) */
+		eth_phy0: ethernet-phy@0 {
+			/* compatible = "ethernet-phy-id0243.0c54";*/
+			max-speed = <100>;
+			reg = <0>;
+
+			reset-assert-us = <10000>;
+			reset-deassert-us = <10000>;
+			reset-gpios = <&gpio GPIOZ_5 GPIO_ACTIVE_LOW>;
+		};
+	};
+};
+
+/* Internal I2C bus (on CPU module) */
+&i2c1 {
+	status = "okay";
+	pinctrl-0 = <&i2c1_z_pins>;
+	pinctrl-names = "default";
+
+	/* RTC */
+	pcf8563: pcf8563@51 {
+		compatible = "nxp,pcf8563";
+		reg = <0x51>;
+		status = "okay";
+	};
+};
+
+/* Peripheral I2C bus (on motherboard) */
+&i2c_AO {
+	status = "okay";
+	pinctrl-0 = <&i2c_ao_sck_10_pins>, <&i2c_ao_sda_11_pins>;
+	pinctrl-names = "default";
+};
+
+&pwm_ab {
+	status = "okay";
+	pinctrl-0 = <&pwm_a_x20_pins>;
+	pinctrl-names = "default";
+};
+
+/* wifi module */
+&sd_emmc_b {
+	status = "okay";
+	#address-cells = <1>;
+	#size-cells = <0>;
+
+	pinctrl-0 = <&sdio_pins>;
+	pinctrl-1 = <&sdio_clk_gate_pins>;
+	pinctrl-names = "default", "clk-gate";
+
+	bus-width = <4>;
+	cap-sd-highspeed;
+	sd-uhs-sdr104;
+	max-frequency = <200000000>;
+	non-removable;
+	disable-wp;
+
+	mmc-pwrseq = <&sdio_pwrseq>;
+
+	vmmc-supply = <&vddao_3v3>;
+	vqmmc-supply = <&vddio_boot>;
+
+	brcmf: wifi@1 {
+		reg = <1>;
+		compatible = "brcm,bcm4329-fmac";
+	};
+};
+
+/* emmc storage */
+&sd_emmc_c {
+	status = "okay";
+	pinctrl-0 = <&emmc_pins>, <&emmc_ds_pins>;
+	pinctrl-1 = <&emmc_clk_gate_pins>;
+	pinctrl-names = "default", "clk-gate";
+
+	bus-width = <8>;
+	cap-mmc-highspeed;
+	max-frequency = <200000000>;
+	non-removable;
+	disable-wp;
+	mmc-ddr-1_8v;
+	mmc-hs200-1_8v;
+
+	mmc-pwrseq = <&emmc_pwrseq>;
+
+	vmmc-supply = <&vcc_3v3>;
+	vqmmc-supply = <&vddio_boot>;
+};
+
+/* UART Bluetooth */
+&uart_B {
+	status = "okay";
+	pinctrl-0 = <&uart_b_z_pins>, <&uart_b_z_cts_rts_pins>;
+	pinctrl-names = "default";
+	uart-has-rtscts;
+
+	bluetooth {
+		compatible = "brcm,bcm43438-bt";
+		shutdown-gpios = <&gpio GPIOZ_7 GPIO_ACTIVE_HIGH>;
+	};
+};
+
+/* UART Console */
+&uart_AO {
+	status = "okay";
+	pinctrl-0 = <&uart_ao_a_pins>;
+	pinctrl-names = "default";
+};
+
+/* UART Wireless module */
+&uart_AO_B {
+	status = "okay";
+	pinctrl-0 = <&uart_ao_b_pins>;
+	pinctrl-names = "default";
+};
+
+&usb {
+	status = "okay";
+	phy-supply = <&usb_pwr>;
+};
+
+&spicc1 {
+	status = "okay";
+	pinctrl-0 = <&spi1_x_pins>, <&spi1_ss0_x_pins>;
+	pinctrl-names = "default";
+};
+
+&gpio {
+	gpio-line-names =
+		"", "", "", "", "", // 0 - 4
+		"", "", "", "", "", // 5 - 9
+		"UserButton", "", "", "", "", // 10 - 14
+		"", "", "", "", "", // 15 - 19
+		"", "", "", "", "", // 20 - 24
+		"", "LedRed", "LedGreen", "Output3", "Output2", // 25 - 29
+		"Output1", "", "", "", "", // 30 - 34
+		"", "ZigBeeBOOT", "", "", "", // 35 - 39
+		"1Wire", "ZigBeeRESET", "", "Input4", "Input3", // 40 - 44
+		"Input2", "Input1", "", "", "", // 45 - 49
+		"", "", "", "", "", // 50 - 54
+		"", "", "", "", "", // 55 - 59
+		"", "", "", "", "", // 60 - 64
+		"", "", "", "", "", // 65 - 69
+		"", "", "", "", "", // 70 - 74
+		"", "", "", "", "", // 75 - 79
+		"", "", "", "", "", // 80 - 84
+		"", ""; // 85-86
+};
+
+&cpu0 {
+	#cooling-cells = <2>;
+};
+
+&cpu1 {
+	#cooling-cells = <2>;
+};
+
+&cpu2 {
+	#cooling-cells = <2>;
+};
+
+&cpu3 {
+	#cooling-cells = <2>;
+};
diff --git a/arch/arm64/boot/dts/amlogic/meson-g12a-radxa-zero.dts b/arch/arm64/boot/dts/amlogic/meson-g12a-radxa-zero.dts
new file mode 100644
index 000000000000..e3bb6df42ff3
--- /dev/null
+++ b/arch/arm64/boot/dts/amlogic/meson-g12a-radxa-zero.dts
@@ -0,0 +1,405 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright (c) 2018 BayLibre SAS. All rights reserved.
+ */
+
+/dts-v1/;
+
+#include "meson-g12a.dtsi"
+#include <dt-bindings/gpio/meson-g12a-gpio.h>
+#include <dt-bindings/sound/meson-g12a-tohdmitx.h>
+
+/ {
+	compatible = "radxa,zero", "amlogic,g12a";
+	model = "Radxa Zero";
+
+	aliases {
+		serial0 = &uart_AO;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	memory@0 {
+		device_type = "memory";
+		reg = <0x0 0x0 0x0 0x40000000>;
+	};
+
+	cvbs-connector {
+		status = "disabled";
+		compatible = "composite-video-connector";
+
+		port {
+			cvbs_connector_in: endpoint {
+				remote-endpoint = <&cvbs_vdac_out>;
+			};
+		};
+	};
+
+	hdmi-connector {
+		compatible = "hdmi-connector";
+		type = "a";
+
+		port {
+			hdmi_connector_in: endpoint {
+				remote-endpoint = <&hdmi_tx_tmds_out>;
+			};
+		};
+	};
+
+	emmc_pwrseq: emmc-pwrseq {
+		compatible = "mmc-pwrseq-emmc";
+		reset-gpios = <&gpio BOOT_12 GPIO_ACTIVE_LOW>;
+	};
+
+	sdio_pwrseq: sdio-pwrseq {
+		compatible = "mmc-pwrseq-simple";
+		reset-gpios = <&gpio GPIOX_6 GPIO_ACTIVE_LOW>;
+		clocks = <&wifi32k>;
+		clock-names = "ext_clock";
+	};
+
+	ao_5v: regulator-ao_5v {
+		compatible = "regulator-fixed";
+		regulator-name = "AO_5V";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		regulator-always-on;
+	};
+
+	vcc_1v8: regulator-vcc_1v8 {
+		compatible = "regulator-fixed";
+		regulator-name = "VCC_1V8";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+		vin-supply = <&vcc_3v3>;
+		regulator-always-on;
+	};
+
+	vcc_3v3: regulator-vcc_3v3 {
+		compatible = "regulator-fixed";
+		regulator-name = "VCC_3V3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		vin-supply = <&vddao_3v3>;
+		regulator-always-on;
+	};
+
+	hdmi_pw: regulator-hdmi_pw {
+		compatible = "regulator-fixed";
+		regulator-name = "HDMI_PW";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		vin-supply = <&ao_5v>;
+		regulator-always-on;
+	};
+
+	vddao_1v8: regulator-vddao_1v8 {
+		compatible = "regulator-fixed";
+		regulator-name = "VDDAO_1V8";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+		vin-supply = <&vddao_3v3>;
+		regulator-always-on;
+	};
+
+	vddao_3v3: regulator-vddao_3v3 {
+		compatible = "regulator-fixed";
+		regulator-name = "VDDAO_3V3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		vin-supply = <&ao_5v>;
+		regulator-always-on;
+	};
+
+	vddcpu: regulator-vddcpu {
+		compatible = "pwm-regulator";
+
+		regulator-name = "VDDCPU";
+		regulator-min-microvolt = <721000>;
+		regulator-max-microvolt = <1022000>;
+
+		vin-supply = <&ao_5v>;
+
+		pwms = <&pwm_AO_cd 1 1250 0>;
+		pwm-dutycycle-range = <100 0>;
+
+		regulator-boot-on;
+		regulator-always-on;
+	};
+
+	sound {
+		compatible = "amlogic,axg-sound-card";
+		model = "RADXA-ZERO";
+		audio-aux-devs = <&tdmout_b>;
+		audio-routing = "TDMOUT_B IN 0", "FRDDR_A OUT 1",
+				"TDMOUT_B IN 1", "FRDDR_B OUT 1",
+				"TDMOUT_B IN 2", "FRDDR_C OUT 1",
+				"TDM_B Playback", "TDMOUT_B OUT";
+
+		assigned-clocks = <&clkc CLKID_MPLL2>,
+				  <&clkc CLKID_MPLL0>,
+				  <&clkc CLKID_MPLL1>;
+		assigned-clock-parents = <0>, <0>, <0>;
+		assigned-clock-rates = <294912000>,
+				       <270950400>,
+				       <393216000>;
+		status = "okay";
+
+		dai-link-0 {
+			sound-dai = <&frddr_a>;
+		};
+
+		dai-link-1 {
+			sound-dai = <&frddr_b>;
+		};
+
+		dai-link-2 {
+			sound-dai = <&frddr_c>;
+		};
+
+		/* 8ch hdmi interface */
+		dai-link-3 {
+			sound-dai = <&tdmif_b>;
+			dai-format = "i2s";
+			dai-tdm-slot-tx-mask-0 = <1 1>;
+			dai-tdm-slot-tx-mask-1 = <1 1>;
+			dai-tdm-slot-tx-mask-2 = <1 1>;
+			dai-tdm-slot-tx-mask-3 = <1 1>;
+			mclk-fs = <256>;
+
+			codec {
+				sound-dai = <&tohdmitx TOHDMITX_I2S_IN_B>;
+			};
+		};
+
+		dai-link-4 {
+			sound-dai = <&tohdmitx TOHDMITX_I2S_OUT>;
+
+			codec {
+				sound-dai = <&hdmi_tx>;
+			};
+		};
+	};
+
+	wifi32k: wifi32k {
+		compatible = "pwm-clock";
+		#clock-cells = <0>;
+		clock-frequency = <32768>;
+		pwms = <&pwm_ef 0 30518 0>; /* PWM_E at 32.768KHz */
+	};
+};
+
+&arb {
+	status = "okay";
+};
+
+&cec_AO {
+	pinctrl-0 = <&cec_ao_a_h_pins>;
+	pinctrl-names = "default";
+	status = "disabled";
+	hdmi-phandle = <&hdmi_tx>;
+};
+
+&cecb_AO {
+	pinctrl-0 = <&cec_ao_b_h_pins>;
+	pinctrl-names = "default";
+	status = "okay";
+	hdmi-phandle = <&hdmi_tx>;
+};
+
+&clkc_audio {
+	status = "okay";
+};
+
+&cpu0 {
+	cpu-supply = <&vddcpu>;
+	operating-points-v2 = <&cpu_opp_table>;
+	clocks = <&clkc CLKID_CPU_CLK>;
+	clock-latency = <50000>;
+};
+
+&cpu1 {
+	cpu-supply = <&vddcpu>;
+	operating-points-v2 = <&cpu_opp_table>;
+	clocks = <&clkc CLKID_CPU_CLK>;
+	clock-latency = <50000>;
+};
+
+&cpu2 {
+	cpu-supply = <&vddcpu>;
+	operating-points-v2 = <&cpu_opp_table>;
+	clocks = <&clkc CLKID_CPU_CLK>;
+	clock-latency = <50000>;
+};
+
+&cpu3 {
+	cpu-supply = <&vddcpu>;
+	operating-points-v2 = <&cpu_opp_table>;
+	clocks = <&clkc CLKID_CPU_CLK>;
+	clock-latency = <50000>;
+};
+
+&cvbs_vdac_port {
+	cvbs_vdac_out: endpoint {
+		remote-endpoint = <&cvbs_connector_in>;
+	};
+};
+
+&frddr_a {
+	status = "okay";
+};
+
+&frddr_b {
+	status = "okay";
+};
+
+&frddr_c {
+	status = "okay";
+};
+
+&hdmi_tx {
+	status = "okay";
+	pinctrl-0 = <&hdmitx_hpd_pins>, <&hdmitx_ddc_pins>;
+	pinctrl-names = "default";
+	hdmi-supply = <&hdmi_pw>;
+};
+
+&hdmi_tx_tmds_port {
+	hdmi_tx_tmds_out: endpoint {
+		remote-endpoint = <&hdmi_connector_in>;
+	};
+};
+
+&ir {
+	status = "disabled";
+	pinctrl-0 = <&remote_input_ao_pins>;
+	pinctrl-names = "default";
+};
+
+&pwm_AO_cd {
+	pinctrl-0 = <&pwm_ao_d_e_pins>;
+	pinctrl-names = "default";
+	clocks = <&xtal>;
+	clock-names = "clkin1";
+	status = "okay";
+};
+
+&pwm_ef {
+	status = "okay";
+	pinctrl-0 = <&pwm_e_pins>;
+	pinctrl-names = "default";
+	clocks = <&xtal>;
+	clock-names = "clkin0";
+};
+
+&saradc {
+	status = "okay";
+	vref-supply = <&vddao_1v8>;
+};
+
+/* SDIO */
+&sd_emmc_a {
+	status = "okay";
+	pinctrl-0 = <&sdio_pins>;
+	pinctrl-1 = <&sdio_clk_gate_pins>;
+	pinctrl-names = "default", "clk-gate";
+	#address-cells = <1>;
+	#size-cells = <0>;
+
+	bus-width = <4>;
+	cap-sd-highspeed;
+	sd-uhs-sdr50;
+	max-frequency = <100000000>;
+
+	non-removable;
+	disable-wp;
+
+	/* WiFi firmware requires power to be kept while in suspend */
+	keep-power-in-suspend;
+
+	mmc-pwrseq = <&sdio_pwrseq>;
+
+	vmmc-supply = <&vddao_3v3>;
+	vqmmc-supply = <&vddao_1v8>;
+
+	brcmf: wifi@1 {
+		reg = <1>;
+		compatible = "brcm,bcm4329-fmac";
+	};
+};
+
+/* SD card */
+&sd_emmc_b {
+	status = "okay";
+	pinctrl-0 = <&sdcard_c_pins>;
+	pinctrl-1 = <&sdcard_clk_gate_c_pins>;
+	pinctrl-names = "default", "clk-gate";
+
+	bus-width = <4>;
+	cap-sd-highspeed;
+	max-frequency = <100000000>;
+	disable-wp;
+
+	cd-gpios = <&gpio GPIOC_6 GPIO_ACTIVE_LOW>;
+	vmmc-supply = <&vddao_3v3>;
+	vqmmc-supply = <&vddao_3v3>;
+};
+
+/* eMMC */
+&sd_emmc_c {
+	status = "okay";
+	pinctrl-0 = <&emmc_ctrl_pins>, <&emmc_data_8b_pins>, <&emmc_ds_pins>;
+	pinctrl-1 = <&emmc_clk_gate_pins>;
+	pinctrl-names = "default", "clk-gate";
+
+	bus-width = <8>;
+	cap-mmc-highspeed;
+	mmc-ddr-1_8v;
+	mmc-hs200-1_8v;
+	max-frequency = <200000000>;
+	disable-wp;
+
+	mmc-pwrseq = <&emmc_pwrseq>;
+	vmmc-supply = <&vcc_3v3>;
+	vqmmc-supply = <&vcc_1v8>;
+};
+
+&tdmif_b {
+	status = "okay";
+};
+
+&tdmout_b {
+	status = "okay";
+};
+
+&tohdmitx {
+	status = "okay";
+};
+
+&uart_A {
+	status = "okay";
+	pinctrl-0 = <&uart_a_pins>, <&uart_a_cts_rts_pins>;
+	pinctrl-names = "default";
+	uart-has-rtscts;
+
+	bluetooth {
+		compatible = "brcm,bcm43438-bt";
+		shutdown-gpios = <&gpio GPIOX_17 GPIO_ACTIVE_HIGH>;
+		max-speed = <2000000>;
+		clocks = <&wifi32k>;
+		clock-names = "lpo";
+	};
+};
+
+&uart_AO {
+	status = "okay";
+	pinctrl-0 = <&uart_ao_a_pins>;
+	pinctrl-names = "default";
+};
+
+&usb {
+	status = "okay";
+	dr_mode = "host";
+};
diff --git a/arch/arm64/boot/dts/amlogic/meson-g12a-sei510.dts b/arch/arm64/boot/dts/amlogic/meson-g12a-sei510.dts
index 81269ccc2496..d8838dde0f0f 100644
--- a/arch/arm64/boot/dts/amlogic/meson-g12a-sei510.dts
+++ b/arch/arm64/boot/dts/amlogic/meson-g12a-sei510.dts
@@ -139,7 +139,7 @@
 		regulator-min-microvolt = <721000>;
 		regulator-max-microvolt = <1022000>;
 
-		vin-supply = <&dc_in>;
+		pwm-supply = <&dc_in>;
 
 		pwms = <&pwm_AO_cd 1 1250 0>;
 		pwm-dutycycle-range = <100 0>;
diff --git a/arch/arm64/boot/dts/amlogic/meson-g12a-u200.dts b/arch/arm64/boot/dts/amlogic/meson-g12a-u200.dts
index a26bfe72550f..4b5d11e56364 100644
--- a/arch/arm64/boot/dts/amlogic/meson-g12a-u200.dts
+++ b/arch/arm64/boot/dts/amlogic/meson-g12a-u200.dts
@@ -139,7 +139,7 @@
 		regulator-min-microvolt = <721000>;
 		regulator-max-microvolt = <1022000>;
 
-		vin-supply = <&main_12v>;
+		pwm-supply = <&main_12v>;
 
 		pwms = <&pwm_AO_cd 1 1250 0>;
 		pwm-dutycycle-range = <100 0>;
diff --git a/arch/arm64/boot/dts/amlogic/meson-g12a-x96-max.dts b/arch/arm64/boot/dts/amlogic/meson-g12a-x96-max.dts
index 579f3d02d613..b4e86196e346 100644
--- a/arch/arm64/boot/dts/amlogic/meson-g12a-x96-max.dts
+++ b/arch/arm64/boot/dts/amlogic/meson-g12a-x96-max.dts
@@ -139,7 +139,7 @@
 		regulator-min-microvolt = <721000>;
 		regulator-max-microvolt = <1022000>;
 
-		vin-supply = <&dc_in>;
+		pwm-supply = <&dc_in>;
 
 		pwms = <&pwm_AO_cd 1 1250 0>;
 		pwm-dutycycle-range = <100 0>;
diff --git a/arch/arm64/boot/dts/amlogic/meson-g12b-khadas-vim3.dtsi b/arch/arm64/boot/dts/amlogic/meson-g12b-khadas-vim3.dtsi
index f42cf4b8af2d..16dd409051b4 100644
--- a/arch/arm64/boot/dts/amlogic/meson-g12b-khadas-vim3.dtsi
+++ b/arch/arm64/boot/dts/amlogic/meson-g12b-khadas-vim3.dtsi
@@ -18,7 +18,7 @@
 		regulator-min-microvolt = <690000>;
 		regulator-max-microvolt = <1050000>;
 
-		vin-supply = <&dc_in>;
+		pwm-supply = <&dc_in>;
 
 		pwms = <&pwm_ab 0 1250 0>;
 		pwm-dutycycle-range = <100 0>;
@@ -37,7 +37,7 @@
 		regulator-min-microvolt = <690000>;
 		regulator-max-microvolt = <1050000>;
 
-		vin-supply = <&vsys_3v3>;
+		pwm-supply = <&vsys_3v3>;
 
 		pwms = <&pwm_AO_cd 1 1250 0>;
 		pwm-dutycycle-range = <100 0>;
diff --git a/arch/arm64/boot/dts/amlogic/meson-g12b-odroid-n2.dtsi b/arch/arm64/boot/dts/amlogic/meson-g12b-odroid-n2.dtsi
index 344573e157a7..e8a00a2f8812 100644
--- a/arch/arm64/boot/dts/amlogic/meson-g12b-odroid-n2.dtsi
+++ b/arch/arm64/boot/dts/amlogic/meson-g12b-odroid-n2.dtsi
@@ -99,6 +99,8 @@
 		regulator-max-microvolt = <5000000>;
 		regulator-always-on;
 		vin-supply = <&main_12v>;
+		gpio = <&gpio GPIOH_8 GPIO_OPEN_DRAIN>;
+		enable-active-high;
 	};
 
 	vcc_1v8: regulator-vcc_1v8 {
@@ -130,7 +132,7 @@
 		regulator-min-microvolt = <721000>;
 		regulator-max-microvolt = <1022000>;
 
-		vin-supply = <&main_12v>;
+		pwm-supply = <&main_12v>;
 
 		pwms = <&pwm_ab 0 1250 0>;
 		pwm-dutycycle-range = <100 0>;
@@ -149,7 +151,7 @@
 		regulator-min-microvolt = <721000>;
 		regulator-max-microvolt = <1022000>;
 
-		vin-supply = <&main_12v>;
+		pwm-supply = <&main_12v>;
 
 		pwms = <&pwm_AO_cd 1 1250 0>;
 		pwm-dutycycle-range = <100 0>;
diff --git a/arch/arm64/boot/dts/amlogic/meson-g12b-w400.dtsi b/arch/arm64/boot/dts/amlogic/meson-g12b-w400.dtsi
index feb088504740..b40d2c1002c9 100644
--- a/arch/arm64/boot/dts/amlogic/meson-g12b-w400.dtsi
+++ b/arch/arm64/boot/dts/amlogic/meson-g12b-w400.dtsi
@@ -96,7 +96,7 @@
 		regulator-min-microvolt = <721000>;
 		regulator-max-microvolt = <1022000>;
 
-		vin-supply = <&main_12v>;
+		pwm-supply = <&main_12v>;
 
 		pwms = <&pwm_ab 0 1250 0>;
 		pwm-dutycycle-range = <100 0>;
@@ -115,7 +115,7 @@
 		regulator-min-microvolt = <721000>;
 		regulator-max-microvolt = <1022000>;
 
-		vin-supply = <&main_12v>;
+		pwm-supply = <&main_12v>;
 
 		pwms = <&pwm_AO_cd 1 1250 0>;
 		pwm-dutycycle-range = <100 0>;
diff --git a/arch/arm64/boot/dts/amlogic/meson-gxl-s905w-jethome-jethub-j80.dts b/arch/arm64/boot/dts/amlogic/meson-gxl-s905w-jethome-jethub-j80.dts
new file mode 100644
index 000000000000..6eafb908695f
--- /dev/null
+++ b/arch/arm64/boot/dts/amlogic/meson-gxl-s905w-jethome-jethub-j80.dts
@@ -0,0 +1,241 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright (c) 2021 Vyacheslav Bocharov <adeep@lexina.in>
+ * Copyright (c) 2020 JetHome
+ * Author: Aleksandr Kazantsev <ak@tvip.ru>
+ * Author: Alexey Shevelkin <ash@tvip.ru>
+ * Author: Vyacheslav Bocharov <adeep@lexina.in>
+ */
+
+/dts-v1/;
+
+#include "meson-gxl.dtsi"
+
+/ {
+	compatible = "jethome,jethub-j80", "amlogic,s905w", "amlogic,meson-gxl";
+	model = "JetHome JetHub J80";
+	memory@0 {
+		device_type = "memory";
+		reg = <0x0 0x0 0x0 0x40000000>;
+	};
+
+	reserved-memory {
+		linux,cma {
+			size = <0x0 0x1000000>;
+		};
+	};
+
+	aliases {
+		serial0 = &uart_AO;   /* Console */
+		serial1 = &uart_A;    /* Bluetooth */
+		serial2 = &uart_AO_B; /* Wireless module 1 */
+		serial3 = &uart_C;    /* Wireless module 2 */
+		ethernet0 = &ethmac;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	vddio_ao18: regulator-vddio_ao18 {
+		compatible = "regulator-fixed";
+		regulator-name = "VDDIO_AO18";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+	};
+
+	vddio_boot: regulator-vddio_boot {
+		compatible = "regulator-fixed";
+		regulator-name = "VDDIO_BOOT";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+	};
+
+	vddao_3v3: regulator-vddao_3v3 {
+		compatible = "regulator-fixed";
+		regulator-name = "VDDAO_3V3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+	};
+
+	vcc_3v3: regulator-vcc_3v3 {
+		compatible = "regulator-fixed";
+		regulator-name = "VCC_3V3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+	};
+
+	emmc_pwrseq: emmc-pwrseq {
+		compatible = "mmc-pwrseq-emmc";
+		reset-gpios = <&gpio BOOT_9 GPIO_ACTIVE_LOW>;
+	};
+
+	wifi32k: wifi32k {
+		compatible = "pwm-clock";
+		#clock-cells = <0>;
+		clock-frequency = <32768>;
+		pwms = <&pwm_ef 0 30518 0>; /* PWM_E at 32.768KHz */
+	};
+
+	sdio_pwrseq: sdio-pwrseq {
+		compatible = "mmc-pwrseq-simple";
+		reset-gpios = <&gpio GPIOX_6 GPIO_ACTIVE_LOW>;
+		clocks = <&wifi32k>;
+		clock-names = "ext_clock";
+	};
+};
+
+&efuse {
+	bt_mac: bt_mac@6 {
+		reg = <0x6 0x6>;
+	};
+
+	wifi_mac: wifi_mac@C {
+		reg = <0xc 0x6>;
+	};
+};
+
+&sn {
+	reg = <0x32 0x20>;
+};
+
+&eth_mac {
+	reg = <0x0 0x6>;
+};
+
+&bid {
+	reg = <0x12 0x20>;
+};
+
+&usb {
+	status = "okay";
+	dr_mode = "host";
+};
+
+&pwm_ef {
+	status = "okay";
+	pinctrl-0 = <&pwm_e_pins>;
+	pinctrl-names = "default";
+	clocks = <&clkc CLKID_FCLK_DIV4>;
+	clock-names = "clkin0";
+};
+
+&saradc {
+	status = "okay";
+	vref-supply = <&vddio_ao18>;
+};
+
+/* Wireless SDIO Module */
+&sd_emmc_a {
+	status = "okay";
+	pinctrl-0 = <&sdio_pins>;
+	pinctrl-1 = <&sdio_clk_gate_pins>;
+	pinctrl-names = "default", "clk-gate";
+	#address-cells = <1>;
+	#size-cells = <0>;
+
+	bus-width = <4>;
+	cap-sd-highspeed;
+	max-frequency = <50000000>;
+
+	non-removable;
+	disable-wp;
+
+	/* WiFi firmware requires power to be kept while in suspend */
+	keep-power-in-suspend;
+
+	mmc-pwrseq = <&sdio_pwrseq>;
+
+	vmmc-supply = <&vddao_3v3>;
+	vqmmc-supply = <&vddio_boot>;
+};
+
+/* SD card */
+&sd_emmc_b {
+	status = "okay";
+	pinctrl-0 = <&sdcard_pins>;
+	pinctrl-1 = <&sdcard_clk_gate_pins>;
+	pinctrl-names = "default", "clk-gate";
+
+	bus-width = <4>;
+	cap-sd-highspeed;
+	max-frequency = <50000000>;
+	disable-wp;
+
+	cd-gpios = <&gpio CARD_6 GPIO_ACTIVE_LOW>;
+
+	vmmc-supply = <&vddao_3v3>;
+	vqmmc-supply = <&vddio_boot>;
+};
+
+/* eMMC */
+&sd_emmc_c {
+	status = "okay";
+	pinctrl-0 = <&emmc_pins>, <&emmc_ds_pins>;
+	pinctrl-1 = <&emmc_clk_gate_pins>;
+	pinctrl-names = "default", "clk-gate";
+
+	bus-width = <8>;
+	cap-mmc-highspeed;
+	max-frequency = <200000000>;
+	non-removable;
+	disable-wp;
+	mmc-ddr-1_8v;
+	mmc-hs200-1_8v;
+
+	mmc-pwrseq = <&emmc_pwrseq>;
+	vmmc-supply = <&vcc_3v3>;
+	vqmmc-supply = <&vddio_boot>;
+};
+
+/* Console UART */
+&uart_AO {
+	status = "okay";
+	pinctrl-0 = <&uart_ao_a_pins>;
+	pinctrl-names = "default";
+};
+
+/* S905W only has access to its internal PHY */
+&ethmac {
+	status = "okay";
+	phy-mode = "rmii";
+	phy-handle = <&internal_phy>;
+};
+
+&internal_phy {
+	status = "okay";
+	pinctrl-0 = <&eth_link_led_pins>, <&eth_act_led_pins>;
+	pinctrl-names = "default";
+};
+
+&uart_A {
+	status = "okay";
+	pinctrl-0 = <&uart_a_pins>, <&uart_a_cts_rts_pins>;
+	pinctrl-names = "default";
+	uart-has-rtscts;
+};
+
+&uart_C {
+	status = "okay";
+	pinctrl-0 = <&uart_c_pins>;
+	pinctrl-names = "default";
+};
+
+&uart_AO_B {
+	status = "okay";
+	pinctrl-0 = <&uart_ao_b_pins>, <&uart_ao_b_cts_rts_pins>;
+	pinctrl-names = "default";
+	uart-has-rtscts;
+};
+
+&i2c_B {
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c_b_pins>;
+
+	pcf8563: pcf8563@51 {
+		compatible = "nxp,pcf8563";
+		reg = <0x51>;
+		status = "okay";
+	};
+};
diff --git a/arch/arm64/boot/dts/amlogic/meson-gxm-rbox-pro.dts b/arch/arm64/boot/dts/amlogic/meson-gxm-rbox-pro.dts
index dde7cfe12cff..50137aafab10 100644
--- a/arch/arm64/boot/dts/amlogic/meson-gxm-rbox-pro.dts
+++ b/arch/arm64/boot/dts/amlogic/meson-gxm-rbox-pro.dts
@@ -14,6 +14,7 @@
 /dts-v1/;
 
 #include "meson-gxm.dtsi"
+#include <dt-bindings/sound/meson-aiu.h>
 
 / {
 	compatible = "kingnovel,r-box-pro", "amlogic,s912", "amlogic,meson-gxm";
@@ -33,6 +34,13 @@
 		reg = <0x0 0x0 0x0 0x80000000>; /* 2 GiB or 3 GiB */
 	};
 
+	spdif_dit: audio-codec-0 {
+		#sound-dai-cells = <0>;
+		compatible = "linux,spdif-dit";
+		status = "okay";
+		sound-name-prefix = "DIT";
+	};
+
 	leds {
 		compatible = "gpio-leds";
 
@@ -90,6 +98,59 @@
 		clocks = <&wifi32k>;
 		clock-names = "ext_clock";
 	};
+
+	sound {
+		compatible = "amlogic,gx-sound-card";
+		model = "RBOX-PRO";
+		assigned-clocks = <&clkc CLKID_MPLL0>,
+				  <&clkc CLKID_MPLL1>,
+				  <&clkc CLKID_MPLL2>;
+		assigned-clock-parents = <0>, <0>, <0>;
+		assigned-clock-rates = <294912000>,
+				       <270950400>,
+				       <393216000>;
+		status = "okay";
+
+		dai-link-0 {
+			sound-dai = <&aiu AIU_CPU CPU_I2S_FIFO>;
+		};
+
+		dai-link-1 {
+			sound-dai = <&aiu AIU_CPU CPU_SPDIF_FIFO>;
+		};
+
+		dai-link-2 {
+			sound-dai = <&aiu AIU_CPU CPU_I2S_ENCODER>;
+			dai-format = "i2s";
+			mclk-fs = <256>;
+
+			codec-0 {
+				sound-dai = <&aiu AIU_HDMI CTRL_I2S>;
+			};
+		};
+
+		dai-link-3 {
+			sound-dai = <&aiu AIU_CPU CPU_SPDIF_ENCODER>;
+
+			codec-0 {
+				sound-dai = <&spdif_dit>;
+			};
+		};
+
+		dai-link-4 {
+			sound-dai = <&aiu AIU_HDMI CTRL_OUT>;
+
+			codec-0 {
+				sound-dai = <&hdmi_tx>;
+			};
+		};
+	};
+};
+
+&aiu {
+	status = "okay";
+	pinctrl-0 = <&spdif_out_h_pins>;
+	pinctrl-names = "default";
 };
 
 &ethmac {
diff --git a/arch/arm64/boot/dts/amlogic/meson-sm1-bananapi-m5.dts b/arch/arm64/boot/dts/amlogic/meson-sm1-bananapi-m5.dts
index effaa138b5f9..212c6aa5a3b8 100644
--- a/arch/arm64/boot/dts/amlogic/meson-sm1-bananapi-m5.dts
+++ b/arch/arm64/boot/dts/amlogic/meson-sm1-bananapi-m5.dts
@@ -173,7 +173,7 @@
 		regulator-min-microvolt = <690000>;
 		regulator-max-microvolt = <1050000>;
 
-		vin-supply = <&dc_in>;
+		pwm-supply = <&dc_in>;
 
 		pwms = <&pwm_AO_cd 1 1250 0>;
 		pwm-dutycycle-range = <100 0>;
diff --git a/arch/arm64/boot/dts/amlogic/meson-sm1-khadas-vim3l.dts b/arch/arm64/boot/dts/amlogic/meson-sm1-khadas-vim3l.dts
index f2c098143594..9c0b544e2209 100644
--- a/arch/arm64/boot/dts/amlogic/meson-sm1-khadas-vim3l.dts
+++ b/arch/arm64/boot/dts/amlogic/meson-sm1-khadas-vim3l.dts
@@ -24,7 +24,7 @@
 		regulator-min-microvolt = <690000>;
 		regulator-max-microvolt = <1050000>;
 
-		vin-supply = <&vsys_3v3>;
+		pwm-supply = <&vsys_3v3>;
 
 		pwms = <&pwm_AO_cd 1 1250 0>;
 		pwm-dutycycle-range = <100 0>;
diff --git a/arch/arm64/boot/dts/amlogic/meson-sm1-odroid.dtsi b/arch/arm64/boot/dts/amlogic/meson-sm1-odroid.dtsi
index fd0ad85c165b..5779e70caccd 100644
--- a/arch/arm64/boot/dts/amlogic/meson-sm1-odroid.dtsi
+++ b/arch/arm64/boot/dts/amlogic/meson-sm1-odroid.dtsi
@@ -116,7 +116,7 @@
 		regulator-min-microvolt = <721000>;
 		regulator-max-microvolt = <1022000>;
 
-		vin-supply = <&main_12v>;
+		pwm-supply = <&main_12v>;
 
 		pwms = <&pwm_AO_cd 1 1250 0>;
 		pwm-dutycycle-range = <100 0>;
@@ -263,6 +263,10 @@
 		reg = <0>;
 		max-speed = <1000>;
 
+		reset-assert-us = <10000>;
+		reset-deassert-us = <80000>;
+		reset-gpios = <&gpio GPIOZ_15 (GPIO_ACTIVE_LOW | GPIO_OPEN_DRAIN)>;
+
 		interrupt-parent = <&gpio_intc>;
 		/* MAC_INTR on GPIOZ_14 */
 		interrupts = <26 IRQ_TYPE_LEVEL_LOW>;
diff --git a/arch/arm64/boot/dts/amlogic/meson-sm1-sei610.dts b/arch/arm64/boot/dts/amlogic/meson-sm1-sei610.dts
index 2194a778973f..427475846fc7 100644
--- a/arch/arm64/boot/dts/amlogic/meson-sm1-sei610.dts
+++ b/arch/arm64/boot/dts/amlogic/meson-sm1-sei610.dts
@@ -185,7 +185,7 @@
 		regulator-min-microvolt = <690000>;
 		regulator-max-microvolt = <1050000>;
 
-		vin-supply = <&dc_in>;
+		pwm-supply = <&dc_in>;
 
 		pwms = <&pwm_AO_cd 1 1500 0>;
 		pwm-dutycycle-range = <100 0>;
diff --git a/arch/arm64/boot/dts/apple/t8103-j274.dts b/arch/arm64/boot/dts/apple/t8103-j274.dts
index e0f6775b9878..33a80f9501dc 100644
--- a/arch/arm64/boot/dts/apple/t8103-j274.dts
+++ b/arch/arm64/boot/dts/apple/t8103-j274.dts
@@ -17,6 +17,7 @@
 
 	aliases {
 		serial0 = &serial0;
+		ethernet0 = &ethernet0;
 	};
 
 	chosen {
@@ -43,3 +44,25 @@
 &serial0 {
 	status = "okay";
 };
+
+/*
+ * Force the bus number assignments so that we can declare some of the
+ * on-board devices and properties that are populated by the bootloader
+ * (such as MAC addresses).
+ */
+&port00 {
+	bus-range = <1 1>;
+};
+
+&port01 {
+	bus-range = <2 2>;
+};
+
+&port02 {
+	bus-range = <3 3>;
+	ethernet0: pci@0,0 {
+		reg = <0x30000 0x0 0x0 0x0 0x0>;
+		/* To be filled by the loader */
+		local-mac-address = [00 10 18 00 00 00];
+	};
+};
diff --git a/arch/arm64/boot/dts/apple/t8103.dtsi b/arch/arm64/boot/dts/apple/t8103.dtsi
index a1e22a2ea2e5..fc8b2bb06ffe 100644
--- a/arch/arm64/boot/dts/apple/t8103.dtsi
+++ b/arch/arm64/boot/dts/apple/t8103.dtsi
@@ -9,6 +9,7 @@
 
 #include <dt-bindings/interrupt-controller/apple-aic.h>
 #include <dt-bindings/interrupt-controller/irq.h>
+#include <dt-bindings/pinctrl/apple.h>
 
 / {
 	compatible = "apple,t8103", "apple,arm-platform";
@@ -131,5 +132,211 @@
 			interrupt-controller;
 			reg = <0x2 0x3b100000 0x0 0x8000>;
 		};
+
+		pinctrl_ap: pinctrl@23c100000 {
+			compatible = "apple,t8103-pinctrl", "apple,pinctrl";
+			reg = <0x2 0x3c100000 0x0 0x100000>;
+
+			gpio-controller;
+			#gpio-cells = <2>;
+			gpio-ranges = <&pinctrl_ap 0 0 212>;
+			apple,npins = <212>;
+
+			interrupt-controller;
+			interrupt-parent = <&aic>;
+			interrupts = <AIC_IRQ 190 IRQ_TYPE_LEVEL_HIGH>,
+				     <AIC_IRQ 191 IRQ_TYPE_LEVEL_HIGH>,
+				     <AIC_IRQ 192 IRQ_TYPE_LEVEL_HIGH>,
+				     <AIC_IRQ 193 IRQ_TYPE_LEVEL_HIGH>,
+				     <AIC_IRQ 194 IRQ_TYPE_LEVEL_HIGH>,
+				     <AIC_IRQ 195 IRQ_TYPE_LEVEL_HIGH>,
+				     <AIC_IRQ 196 IRQ_TYPE_LEVEL_HIGH>;
+
+			pcie_pins: pcie-pins {
+				pinmux = <APPLE_PINMUX(150, 1)>,
+					 <APPLE_PINMUX(151, 1)>,
+					 <APPLE_PINMUX(32, 1)>;
+			};
+		};
+
+		pinctrl_aop: pinctrl@24a820000 {
+			compatible = "apple,t8103-pinctrl", "apple,pinctrl";
+			reg = <0x2 0x4a820000 0x0 0x4000>;
+
+			gpio-controller;
+			#gpio-cells = <2>;
+			gpio-ranges = <&pinctrl_aop 0 0 42>;
+			apple,npins = <42>;
+
+			interrupt-controller;
+			interrupt-parent = <&aic>;
+			interrupts = <AIC_IRQ 268 IRQ_TYPE_LEVEL_HIGH>,
+				     <AIC_IRQ 269 IRQ_TYPE_LEVEL_HIGH>,
+				     <AIC_IRQ 270 IRQ_TYPE_LEVEL_HIGH>,
+				     <AIC_IRQ 271 IRQ_TYPE_LEVEL_HIGH>,
+				     <AIC_IRQ 272 IRQ_TYPE_LEVEL_HIGH>,
+				     <AIC_IRQ 273 IRQ_TYPE_LEVEL_HIGH>,
+				     <AIC_IRQ 274 IRQ_TYPE_LEVEL_HIGH>;
+		};
+
+		pinctrl_nub: pinctrl@23d1f0000 {
+			compatible = "apple,t8103-pinctrl", "apple,pinctrl";
+			reg = <0x2 0x3d1f0000 0x0 0x4000>;
+
+			gpio-controller;
+			#gpio-cells = <2>;
+			gpio-ranges = <&pinctrl_nub 0 0 23>;
+			apple,npins = <23>;
+
+			interrupt-controller;
+			interrupt-parent = <&aic>;
+			interrupts = <AIC_IRQ 330 IRQ_TYPE_LEVEL_HIGH>,
+				     <AIC_IRQ 331 IRQ_TYPE_LEVEL_HIGH>,
+				     <AIC_IRQ 332 IRQ_TYPE_LEVEL_HIGH>,
+				     <AIC_IRQ 333 IRQ_TYPE_LEVEL_HIGH>,
+				     <AIC_IRQ 334 IRQ_TYPE_LEVEL_HIGH>,
+				     <AIC_IRQ 335 IRQ_TYPE_LEVEL_HIGH>,
+				     <AIC_IRQ 336 IRQ_TYPE_LEVEL_HIGH>;
+		};
+
+		pinctrl_smc: pinctrl@23e820000 {
+			compatible = "apple,t8103-pinctrl", "apple,pinctrl";
+			reg = <0x2 0x3e820000 0x0 0x4000>;
+
+			gpio-controller;
+			#gpio-cells = <2>;
+			gpio-ranges = <&pinctrl_smc 0 0 16>;
+			apple,npins = <16>;
+
+			interrupt-controller;
+			interrupt-parent = <&aic>;
+			interrupts = <AIC_IRQ 391 IRQ_TYPE_LEVEL_HIGH>,
+				     <AIC_IRQ 392 IRQ_TYPE_LEVEL_HIGH>,
+				     <AIC_IRQ 393 IRQ_TYPE_LEVEL_HIGH>,
+				     <AIC_IRQ 394 IRQ_TYPE_LEVEL_HIGH>,
+				     <AIC_IRQ 395 IRQ_TYPE_LEVEL_HIGH>,
+				     <AIC_IRQ 396 IRQ_TYPE_LEVEL_HIGH>,
+				     <AIC_IRQ 397 IRQ_TYPE_LEVEL_HIGH>;
+		};
+
+		pcie0_dart_0: dart@681008000 {
+			compatible = "apple,t8103-dart";
+			reg = <0x6 0x81008000 0x0 0x4000>;
+			#iommu-cells = <1>;
+			interrupt-parent = <&aic>;
+			interrupts = <AIC_IRQ 696 IRQ_TYPE_LEVEL_HIGH>;
+		};
+
+		pcie0_dart_1: dart@682008000 {
+			compatible = "apple,t8103-dart";
+			reg = <0x6 0x82008000 0x0 0x4000>;
+			#iommu-cells = <1>;
+			interrupt-parent = <&aic>;
+			interrupts = <AIC_IRQ 699 IRQ_TYPE_LEVEL_HIGH>;
+		};
+
+		pcie0_dart_2: dart@683008000 {
+			compatible = "apple,t8103-dart";
+			reg = <0x6 0x83008000 0x0 0x4000>;
+			#iommu-cells = <1>;
+			interrupt-parent = <&aic>;
+			interrupts = <AIC_IRQ 702 IRQ_TYPE_LEVEL_HIGH>;
+		};
+
+		pcie0: pcie@690000000 {
+			compatible = "apple,t8103-pcie", "apple,pcie";
+			device_type = "pci";
+
+			reg = <0x6 0x90000000 0x0 0x1000000>,
+			      <0x6 0x80000000 0x0 0x100000>,
+			      <0x6 0x81000000 0x0 0x4000>,
+			      <0x6 0x82000000 0x0 0x4000>,
+			      <0x6 0x83000000 0x0 0x4000>;
+			reg-names = "config", "rc", "port0", "port1", "port2";
+
+			interrupt-parent = <&aic>;
+			interrupts = <AIC_IRQ 695 IRQ_TYPE_LEVEL_HIGH>,
+				     <AIC_IRQ 698 IRQ_TYPE_LEVEL_HIGH>,
+				     <AIC_IRQ 701 IRQ_TYPE_LEVEL_HIGH>;
+
+			msi-controller;
+			msi-parent = <&pcie0>;
+			msi-ranges = <&aic AIC_IRQ 704 IRQ_TYPE_EDGE_RISING 32>;
+
+
+			iommu-map = <0x100 &pcie0_dart_0 1 1>,
+				    <0x200 &pcie0_dart_1 1 1>,
+				    <0x300 &pcie0_dart_2 1 1>;
+			iommu-map-mask = <0xff00>;
+
+			bus-range = <0 3>;
+			#address-cells = <3>;
+			#size-cells = <2>;
+			ranges = <0x43000000 0x6 0xa0000000 0x6 0xa0000000 0x0 0x20000000>,
+				 <0x02000000 0x0 0xc0000000 0x6 0xc0000000 0x0 0x40000000>;
+
+			pinctrl-0 = <&pcie_pins>;
+			pinctrl-names = "default";
+
+			port00: pci@0,0 {
+				device_type = "pci";
+				reg = <0x0 0x0 0x0 0x0 0x0>;
+				reset-gpios = <&pinctrl_ap 152 0>;
+				max-link-speed = <2>;
+
+				#address-cells = <3>;
+				#size-cells = <2>;
+				ranges;
+
+				interrupt-controller;
+				#interrupt-cells = <1>;
+
+				interrupt-map-mask = <0 0 0 7>;
+				interrupt-map = <0 0 0 1 &port00 0 0 0 0>,
+						<0 0 0 2 &port00 0 0 0 1>,
+						<0 0 0 3 &port00 0 0 0 2>,
+						<0 0 0 4 &port00 0 0 0 3>;
+			};
+
+			port01: pci@1,0 {
+				device_type = "pci";
+				reg = <0x800 0x0 0x0 0x0 0x0>;
+				reset-gpios = <&pinctrl_ap 153 0>;
+				max-link-speed = <2>;
+
+				#address-cells = <3>;
+				#size-cells = <2>;
+				ranges;
+
+				interrupt-controller;
+				#interrupt-cells = <1>;
+
+				interrupt-map-mask = <0 0 0 7>;
+				interrupt-map = <0 0 0 1 &port01 0 0 0 0>,
+						<0 0 0 2 &port01 0 0 0 1>,
+						<0 0 0 3 &port01 0 0 0 2>,
+						<0 0 0 4 &port01 0 0 0 3>;
+			};
+
+			port02: pci@2,0 {
+				device_type = "pci";
+				reg = <0x1000 0x0 0x0 0x0 0x0>;
+				reset-gpios = <&pinctrl_ap 33 0>;
+				max-link-speed = <1>;
+
+				#address-cells = <3>;
+				#size-cells = <2>;
+				ranges;
+
+				interrupt-controller;
+				#interrupt-cells = <1>;
+
+				interrupt-map-mask = <0 0 0 7>;
+				interrupt-map = <0 0 0 1 &port02 0 0 0 0>,
+						<0 0 0 2 &port02 0 0 0 1>,
+						<0 0 0 3 &port02 0 0 0 2>,
+						<0 0 0 4 &port02 0 0 0 3>;
+			};
+		};
 	};
 };
diff --git a/arch/arm64/boot/dts/arm/juno-motherboard.dtsi b/arch/arm64/boot/dts/arm/juno-motherboard.dtsi
index fefd2b5f0176..be42932f7e21 100644
--- a/arch/arm64/boot/dts/arm/juno-motherboard.dtsi
+++ b/arch/arm64/boot/dts/arm/juno-motherboard.dtsi
@@ -160,64 +160,75 @@
 				apbregs@10000 {
 					compatible = "syscon", "simple-mfd";
 					reg = <0x010000 0x1000>;
+					ranges = <0x0 0x10000 0x1000>;
+					#address-cells = <1>;
+					#size-cells = <1>;
 
-					led0 {
+					led@8,0 {
 						compatible = "register-bit-led";
+						reg = <0x08 0x04>;
 						offset = <0x08>;
 						mask = <0x01>;
 						label = "vexpress:0";
 						linux,default-trigger = "heartbeat";
 						default-state = "on";
 					};
-					led1 {
+					led@8,1 {
 						compatible = "register-bit-led";
+						reg = <0x08 0x04>;
 						offset = <0x08>;
 						mask = <0x02>;
 						label = "vexpress:1";
 						linux,default-trigger = "mmc0";
 						default-state = "off";
 					};
-					led2 {
+					led@8,2 {
 						compatible = "register-bit-led";
+						reg = <0x08 0x04>;
 						offset = <0x08>;
 						mask = <0x04>;
 						label = "vexpress:2";
 						linux,default-trigger = "cpu0";
 						default-state = "off";
 					};
-					led3 {
+					led@8,3 {
 						compatible = "register-bit-led";
+						reg = <0x08 0x04>;
 						offset = <0x08>;
 						mask = <0x08>;
 						label = "vexpress:3";
 						linux,default-trigger = "cpu1";
 						default-state = "off";
 					};
-					led4 {
+					led@8,4 {
 						compatible = "register-bit-led";
+						reg = <0x08 0x04>;
 						offset = <0x08>;
 						mask = <0x10>;
 						label = "vexpress:4";
 						linux,default-trigger = "cpu2";
 						default-state = "off";
 					};
-					led5 {
+					led@8,5 {
 						compatible = "register-bit-led";
+						reg = <0x08 0x04>;
 						offset = <0x08>;
 						mask = <0x20>;
 						label = "vexpress:5";
 						linux,default-trigger = "cpu3";
 						default-state = "off";
 					};
-					led6 {
+					led@8,6 {
 						compatible = "register-bit-led";
+						reg = <0x08 0x04>;
 						offset = <0x08>;
 						mask = <0x40>;
 						label = "vexpress:6";
 						default-state = "off";
 					};
-					led7 {
+					led@8,7 {
 						compatible = "register-bit-led";
+						reg = <0x08 0x04>;
 						offset = <0x08>;
 						mask = <0x80>;
 						label = "vexpress:7";
diff --git a/arch/arm64/boot/dts/broadcom/Makefile b/arch/arm64/boot/dts/broadcom/Makefile
index 11eae3e3a944..c6882032a428 100644
--- a/arch/arm64/boot/dts/broadcom/Makefile
+++ b/arch/arm64/boot/dts/broadcom/Makefile
@@ -1,6 +1,7 @@
 # SPDX-License-Identifier: GPL-2.0
 dtb-$(CONFIG_ARCH_BCM2835) += bcm2711-rpi-400.dtb \
 			      bcm2711-rpi-4-b.dtb \
+			      bcm2711-rpi-cm4-io.dtb \
 			      bcm2837-rpi-3-a-plus.dtb \
 			      bcm2837-rpi-3-b.dtb \
 			      bcm2837-rpi-3-b-plus.dtb \
diff --git a/arch/arm64/boot/dts/broadcom/bcm2711-rpi-cm4-io.dts b/arch/arm64/boot/dts/broadcom/bcm2711-rpi-cm4-io.dts
new file mode 100644
index 000000000000..e36d395e3951
--- /dev/null
+++ b/arch/arm64/boot/dts/broadcom/bcm2711-rpi-cm4-io.dts
@@ -0,0 +1,2 @@
+// SPDX-License-Identifier: GPL-2.0
+#include "arm/bcm2711-rpi-cm4-io.dts"
diff --git a/arch/arm64/boot/dts/broadcom/bcm4908/bcm4908.dtsi b/arch/arm64/boot/dts/broadcom/bcm4908/bcm4908.dtsi
index a5a64d17d9ea..984c737fa627 100644
--- a/arch/arm64/boot/dts/broadcom/bcm4908/bcm4908.dtsi
+++ b/arch/arm64/boot/dts/broadcom/bcm4908/bcm4908.dtsi
@@ -292,11 +292,11 @@
 			reg = <0x640 0x18>;
 			interrupts = <GIC_SPI 32 IRQ_TYPE_LEVEL_HIGH>;
 			clocks = <&periph_clk>;
-			clock-names = "periph";
+			clock-names = "refclk";
 			status = "okay";
 		};
 
-		nand@1800 {
+		nand-controller@1800 {
 			#address-cells = <1>;
 			#size-cells = <0>;
 			compatible = "brcm,nand-bcm63138", "brcm,brcmnand-v7.1", "brcm,brcmnand";
@@ -326,12 +326,12 @@
 				#reset-cells = <1>;
 			};
 		};
+	};
 
-		reboot {
-			compatible = "syscon-reboot";
-			regmap = <&timer>;
-			offset = <0x34>;
-			mask = <1>;
-		};
+	reboot {
+		compatible = "syscon-reboot";
+		regmap = <&timer>;
+		offset = <0x34>;
+		mask = <1>;
 	};
 };
diff --git a/arch/arm64/boot/dts/exynos/Makefile b/arch/arm64/boot/dts/exynos/Makefile
index e0a2facde6a2..b41e86df0a84 100644
--- a/arch/arm64/boot/dts/exynos/Makefile
+++ b/arch/arm64/boot/dts/exynos/Makefile
@@ -2,4 +2,5 @@
 dtb-$(CONFIG_ARCH_EXYNOS) += \
 	exynos5433-tm2.dtb	\
 	exynos5433-tm2e.dtb	\
-	exynos7-espresso.dtb
+	exynos7-espresso.dtb	\
+	exynosautov9-sadk.dtb
diff --git a/arch/arm64/boot/dts/exynos/exynos5433-bus.dtsi b/arch/arm64/boot/dts/exynos/exynos5433-bus.dtsi
index 8997f8f2b96c..72ccf18eb9d1 100644
--- a/arch/arm64/boot/dts/exynos/exynos5433-bus.dtsi
+++ b/arch/arm64/boot/dts/exynos/exynos5433-bus.dtsi
@@ -87,7 +87,7 @@
 		status = "disabled";
 	};
 
-	bus_g2d_400_opp_table: opp-table2 {
+	bus_g2d_400_opp_table: opp-table-2 {
 		compatible = "operating-points-v2";
 		opp-shared;
 
@@ -117,7 +117,7 @@
 		};
 	};
 
-	bus_g2d_266_opp_table: opp-table3 {
+	bus_g2d_266_opp_table: opp-table-3 {
 		compatible = "operating-points-v2";
 
 		opp-267000000 {
@@ -137,7 +137,7 @@
 		};
 	};
 
-	bus_gscl_opp_table: opp-table4 {
+	bus_gscl_opp_table: opp-table-4 {
 		compatible = "operating-points-v2";
 
 		opp-333000000 {
@@ -151,7 +151,7 @@
 		};
 	};
 
-	bus_hevc_opp_table: opp-table5 {
+	bus_hevc_opp_table: opp-table-5 {
 		compatible = "operating-points-v2";
 		opp-shared;
 
@@ -175,7 +175,7 @@
 		};
 	};
 
-	bus_noc2_opp_table: opp-table6 {
+	bus_noc2_opp_table: opp-table-6 {
 		compatible = "operating-points-v2";
 
 		opp-400000000 {
diff --git a/arch/arm64/boot/dts/exynos/exynos5433-tm2.dts b/arch/arm64/boot/dts/exynos/exynos5433-tm2.dts
index fdd0796b29d4..aca01709fd29 100644
--- a/arch/arm64/boot/dts/exynos/exynos5433-tm2.dts
+++ b/arch/arm64/boot/dts/exynos/exynos5433-tm2.dts
@@ -13,6 +13,7 @@
 / {
 	model = "Samsung TM2 board";
 	compatible = "samsung,tm2", "samsung,exynos5433";
+	chassis-type = "handset";
 };
 
 &cmu_disp {
diff --git a/arch/arm64/boot/dts/exynos/exynos5433-tm2e.dts b/arch/arm64/boot/dts/exynos/exynos5433-tm2e.dts
index 089fc7a1af67..22d26460f3dd 100644
--- a/arch/arm64/boot/dts/exynos/exynos5433-tm2e.dts
+++ b/arch/arm64/boot/dts/exynos/exynos5433-tm2e.dts
@@ -13,6 +13,7 @@
 / {
 	model = "Samsung TM2E board";
 	compatible = "samsung,tm2e", "samsung,exynos5433";
+	chassis-type = "handset";
 };
 
 &cmu_disp {
diff --git a/arch/arm64/boot/dts/exynos/exynos5433.dtsi b/arch/arm64/boot/dts/exynos/exynos5433.dtsi
index 6a6f7dd1d65c..4422021cf4b2 100644
--- a/arch/arm64/boot/dts/exynos/exynos5433.dtsi
+++ b/arch/arm64/boot/dts/exynos/exynos5433.dtsi
@@ -239,7 +239,7 @@
 		};
 	};
 
-	cluster_a53_opp_table: opp-table0 {
+	cluster_a53_opp_table: opp-table-0 {
 		compatible = "operating-points-v2";
 		opp-shared;
 
@@ -285,7 +285,7 @@
 		};
 	};
 
-	cluster_a57_opp_table: opp-table1 {
+	cluster_a57_opp_table: opp-table-1 {
 		compatible = "operating-points-v2";
 		opp-shared;
 
@@ -1132,7 +1132,7 @@
 		};
 
 		syscon_fsys: syscon@156f0000 {
-			compatible = "syscon";
+			compatible = "samsung,exynos5433-sysreg", "syscon";
 			reg = <0x156f0000 0x1044>;
 		};
 
diff --git a/arch/arm64/boot/dts/exynos/exynosautov9-pinctrl.dtsi b/arch/arm64/boot/dts/exynos/exynosautov9-pinctrl.dtsi
new file mode 100644
index 000000000000..2407b03b5404
--- /dev/null
+++ b/arch/arm64/boot/dts/exynos/exynosautov9-pinctrl.dtsi
@@ -0,0 +1,1189 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Samsung's ExynosAutov9 SoC pin-mux and pin-config device tree source
+ *
+ * Copyright (c) 2021 Samsung Electronics Co., Ltd.
+ *
+ * Samsung's ExynosAutov9 SoC pin-mux and pin-config options are listed as
+ * device tree nodes in this file.
+ */
+
+#include <dt-bindings/pinctrl/samsung.h>
+
+&pinctrl_alive {
+	gpa0: gpa0 {
+		gpio-controller;
+		#gpio-cells = <2>;
+		interrupt-controller;
+		#interrupt-cells = <2>;
+		interrupt-parent = <&gic>;
+		interrupts = <GIC_SPI 13 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 14 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 15 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 16 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 17 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 18 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 19 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 20 IRQ_TYPE_LEVEL_HIGH>;
+	};
+
+	gpa1: gpa1 {
+		gpio-controller;
+		#gpio-cells = <2>;
+		interrupt-controller;
+		#interrupt-cells = <2>;
+		interrupt-parent = <&gic>;
+		interrupts = <GIC_SPI 21 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 22 IRQ_TYPE_LEVEL_HIGH>;
+	};
+
+	dp0_hpd: dp0-hpd-pins {
+		samsung,pins = "gpa1-0";
+		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+	};
+
+	dp1_hpd: dp1-hpd-pins {
+		samsung,pins = "gpa1-1";
+		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+	};
+
+	gpq0: gpq0 {
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		interrupt-controller;
+		#interrupt-cells = <2>;
+	};
+
+	speedy0_bus: speedy0-bus-pins {
+		samsung,pins = "gpq0-0";
+		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
+	};
+
+	speedy1_bus: speedy1-bus-pins {
+		samsung,pins = "gpa0-3";
+		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
+	};
+};
+
+&pinctrl_aud {
+	gpb0: gpb0 {
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		interrupt-controller;
+		#interrupt-cells = <2>;
+	};
+
+	gpb1: gpb1 {
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		interrupt-controller;
+		#interrupt-cells = <2>;
+	};
+
+	gpb2: gpb2 {
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		interrupt-controller;
+		#interrupt-cells = <2>;
+	};
+
+	gpb3: gpb3 {
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		interrupt-controller;
+		#interrupt-cells = <2>;
+	};
+
+	aud_codec_mclk: aud-codec-mclk-pins {
+		samsung,pins = "gpb0-4";
+		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+		samsung,pin-pud = <EXYNOS_PIN_PULL_DOWN>;
+	};
+
+	aud_codec_mclk_idle: aud-codec-mclk-idle-pins {
+		samsung,pins = "gpb0-4";
+		samsung,pin-function = <EXYNOS_PIN_FUNC_INPUT>;
+		samsung,pin-pud = <EXYNOS_PIN_PULL_DOWN>;
+	};
+
+	aud_i2s0_bus: aud-i2s0-pins {
+		samsung,pins = "gpb0-0", "gpb0-1", "gpb0-2", "gpb0-3";
+		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+		samsung,pin-pud = <EXYNOS_PIN_PULL_DOWN>;
+	};
+
+	aud_i2s0_idle: aud-i2s0-idle-pins {
+		samsung,pins = "gpb0-0", "gpb0-1", "gpb0-2", "gpb0-3";
+		samsung,pin-function = <EXYNOS_PIN_FUNC_INPUT>;
+		samsung,pin-pud = <EXYNOS_PIN_PULL_DOWN>;
+	};
+
+	aud_i2s1_bus: aud-i2s1-pins {
+		samsung,pins = "gpb1-0", "gpb1-1", "gpb1-2", "gpb1-3";
+		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+		samsung,pin-pud = <EXYNOS_PIN_PULL_DOWN>;
+	};
+
+	aud_i2s1_idle: aud-i2s1-idle-pins {
+		samsung,pins = "gpb1-0", "gpb1-1", "gpb1-2", "gpb1-3";
+		samsung,pin-function = <EXYNOS_PIN_FUNC_INPUT>;
+		samsung,pin-pud = <EXYNOS_PIN_PULL_DOWN>;
+	};
+
+	aud_i2s2_bus: aud-i2s2-pins {
+		samsung,pins = "gpb1-4", "gpb1-5", "gpb1-6", "gpb1-7";
+		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+		samsung,pin-pud = <EXYNOS_PIN_PULL_DOWN>;
+	};
+
+	aud_i2s2_idle: aud-i2s2-idle-pins {
+		samsung,pins = "gpb1-4", "gpb1-5", "gpb1-6", "gpb1-7";
+		samsung,pin-function = <EXYNOS_PIN_FUNC_INPUT>;
+		samsung,pin-pud = <EXYNOS_PIN_PULL_DOWN>;
+	};
+
+	aud_i2s3_bus: aud-i2s3-pins {
+		samsung,pins = "gpb2-0", "gpb2-1", "gpb2-2", "gpb2-3";
+		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+		samsung,pin-pud = <EXYNOS_PIN_PULL_DOWN>;
+	};
+
+	aud_i2s3_idle: aud-i2s3-idle-pins {
+		samsung,pins = "gpb2-0", "gpb2-1", "gpb2-2", "gpb2-3";
+		samsung,pin-function = <EXYNOS_PIN_FUNC_INPUT>;
+		samsung,pin-pud = <EXYNOS_PIN_PULL_DOWN>;
+	};
+
+	aud_i2s4_bus: aud-i2s4-pins {
+		samsung,pins = "gpb2-4", "gpb2-5", "gpb2-6", "gpb2-7";
+		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+		samsung,pin-pud = <EXYNOS_PIN_PULL_DOWN>;
+	};
+
+	aud_i2s4_idle: aud-i2s4-idle-pins {
+		samsung,pins = "gpb2-4", "gpb2-5", "gpb2-6", "gpb2-7";
+		samsung,pin-function = <EXYNOS_PIN_FUNC_INPUT>;
+		samsung,pin-pud = <EXYNOS_PIN_PULL_DOWN>;
+	};
+
+	aud_i2s5_bus: aud-i2s5-pins {
+		samsung,pins = "gpb3-0", "gpb3-1", "gpb3-2", "gpb3-3";
+		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+		samsung,pin-pud = <EXYNOS_PIN_PULL_DOWN>;
+	};
+
+	aud_i2s5_idle: aaud-i2s5-idle-pins {
+		samsung,pins = "gpb3-0", "gpb3-1", "gpb3-2", "gpb3-3";
+		samsung,pin-function = <EXYNOS_PIN_FUNC_INPUT>;
+		samsung,pin-pud = <EXYNOS_PIN_PULL_DOWN>;
+	};
+
+	aud_i2s6_bus: aud-i2s6-pins {
+		samsung,pins = "gpb3-4", "gpb3-5", "gpb3-6", "gpb3-7";
+		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+		samsung,pin-pud = <EXYNOS_PIN_PULL_DOWN>;
+	};
+
+	aud_i2s6_idle: aaud-i2s6-idle-pins {
+		samsung,pins = "gpb3-4", "gpb3-5", "gpb3-6", "gpb3-7";
+		samsung,pin-function = <EXYNOS_PIN_FUNC_INPUT>;
+		samsung,pin-pud = <EXYNOS_PIN_PULL_DOWN>;
+	};
+};
+
+&pinctrl_fsys0 {
+	gpf0: gpf0 {
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		interrupt-controller;
+		#interrupt-cells = <2>;
+	};
+
+	gpf1: gpf1 {
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		interrupt-controller;
+		#interrupt-cells = <2>;
+	};
+
+	pcie_clkreq0: pcie-clkreq0-pins {
+		samsung,pins = "gpf0-0";
+		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
+		samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV4>;
+		samsung,pin-con-pdn = <EXYNOS_PIN_PDN_PREV>;
+		samsung,pin-pud-pdn = <EXYNOS_PIN_PULL_UP>;
+	};
+
+	pcie_perst0_out: pcie-perst0-out-pins {
+		samsung,pins = "gpf0-1";
+		samsung,pin-function = <EXYNOS_PIN_FUNC_OUTPUT>;
+		samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV4>;
+		samsung,pin-con-pdn = <EXYNOS_PIN_PDN_PREV>;
+	};
+
+	pcie_perst0_in: pcie-perst0-in-pins {
+		samsung,pins = "gpf0-1";
+		samsung,pin-function = <EXYNOS_PIN_FUNC_3>;
+		samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV4>;
+		samsung,pin-con-pdn = <EXYNOS_PIN_PDN_PREV>;
+	};
+
+	pcie_clkreq1: pcie-clkreq1-pins {
+		samsung,pins = "gpf0-2";
+		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
+		samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV4>;
+		samsung,pin-con-pdn = <EXYNOS_PIN_PDN_PREV>;
+		samsung,pin-pud-pdn = <EXYNOS_PIN_PULL_UP>;
+	};
+
+	pcie_perst1_out: pcie-perst1-out-pins {
+		samsung,pins = "gpf0-3";
+		samsung,pin-function = <EXYNOS_PIN_FUNC_OUTPUT>;
+		samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV4>;
+		samsung,pin-con-pdn = <EXYNOS_PIN_PDN_PREV>;
+	};
+
+	pcie_perst1_in: pcie-perst1-in-pins {
+		samsung,pins = "gpf0-3";
+		samsung,pin-function = <EXYNOS_PIN_FUNC_3>;
+		samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV4>;
+		samsung,pin-con-pdn = <EXYNOS_PIN_PDN_PREV>;
+	};
+
+	pcie_clkreq2: pcie-clkreq2-pins {
+		samsung,pins = "gpf0-4";
+		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
+		samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV4>;
+		samsung,pin-con-pdn = <EXYNOS_PIN_PDN_PREV>;
+		samsung,pin-pud-pdn = <EXYNOS_PIN_PULL_UP>;
+	};
+
+	pcie_perst2_out: pcie-perst2-out-pins {
+		samsung,pins = "gpf0-5";
+		samsung,pin-function = <EXYNOS_PIN_FUNC_OUTPUT>;
+		samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV4>;
+		samsung,pin-con-pdn = <EXYNOS_PIN_PDN_PREV>;
+	};
+
+	pcie_perst2_in: pcie-perst2-in-pins {
+		samsung,pins = "gpf0-5";
+		samsung,pin-function = <EXYNOS_PIN_FUNC_3>;
+		samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV4>;
+		samsung,pin-con-pdn = <EXYNOS_PIN_PDN_PREV>;
+	};
+
+	pcie_clkreq3: pcie-clkreq3-pins {
+		samsung,pins = "gpf1-0";
+		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
+		samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV4>;
+		samsung,pin-con-pdn = <EXYNOS_PIN_PDN_PREV>;
+		samsung,pin-pud-pdn = <EXYNOS_PIN_PULL_UP>;
+	};
+
+	pcie_perst3_out: pcie-perst3-out-pins {
+		samsung,pins = "gpf1-1";
+		samsung,pin-function = <EXYNOS_PIN_FUNC_OUTPUT>;
+		samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV4>;
+		samsung,pin-con-pdn = <EXYNOS_PIN_PDN_PREV>;
+	};
+
+	pcie_perst3_in: pcie-perst3-in-pins {
+		samsung,pins = "gpf1-1";
+		samsung,pin-function = <EXYNOS_PIN_FUNC_3>;
+		samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV4>;
+		samsung,pin-con-pdn = <EXYNOS_PIN_PDN_PREV>;
+	};
+
+	pcie_clkreq4: pcie-clkreq4-pins {
+		samsung,pins = "gpf1-2";
+		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
+		samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV4>;
+		samsung,pin-con-pdn = <EXYNOS_PIN_PDN_PREV>;
+		samsung,pin-pud-pdn = <EXYNOS_PIN_PULL_UP>;
+	};
+
+	pcie_perst4_out: pcie-perst4-out-pins {
+		samsung,pins = "gpf1-3";
+		samsung,pin-function = <EXYNOS_PIN_FUNC_OUTPUT>;
+		samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV4>;
+		samsung,pin-con-pdn = <EXYNOS_PIN_PDN_PREV>;
+	};
+
+	pcie_perst4_in: pcie-perst4-in-pins {
+		samsung,pins = "gpf1-1";
+		samsung,pin-function = <EXYNOS_PIN_FUNC_3>;
+		samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV4>;
+		samsung,pin-con-pdn = <EXYNOS_PIN_PDN_PREV>;
+	};
+
+	pcie_clkreq5: pcie-clkreq5-pins {
+		samsung,pins = "gpf1-4";
+		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
+		samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV4>;
+		samsung,pin-con-pdn = <EXYNOS_PIN_PDN_PREV>;
+		samsung,pin-pud-pdn = <EXYNOS_PIN_PULL_UP>;
+	};
+
+	pcie_perst5_out: pcie-perst5-out-pins {
+		samsung,pins = "gpf1-5";
+		samsung,pin-function = <EXYNOS_PIN_FUNC_OUTPUT>;
+		samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV4>;
+		samsung,pin-con-pdn = <EXYNOS_PIN_PDN_PREV>;
+	};
+
+	pcie_perst5_in: pcie-perst5-in-pins {
+		samsung,pins = "gpf1-5";
+		samsung,pin-function = <EXYNOS_PIN_FUNC_3>;
+		samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV4>;
+		samsung,pin-con-pdn = <EXYNOS_PIN_PDN_PREV>;
+	};
+};
+
+&pinctrl_fsys1 {
+	gpf8: gpf8 {
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		interrupt-controller;
+		#interrupt-cells = <2>;
+	};
+
+	sd2_clk: sd2-clk-pins {
+		samsung,pins = "gpf8-0";
+		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
+		samsung,pin-drv = <2>;	/* 2x drive strength */
+	};
+
+	sd2_cmd: sd2-cmd-pins {
+		samsung,pins = "gpf8-1";
+		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
+		samsung,pin-drv = <2>;	/* 2x drive strength */
+	};
+
+	sd2_bus1: sd2-bus-width1-pins {
+		samsung,pins = "gpf8-2";
+		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
+		samsung,pin-drv = <2>;	/* 2x drive strength */
+	};
+
+	sd2_bus4: sd2-bus-width4-pins {
+		samsung,pins = "gpf8-3", "gpf8-4", "gpf8-5";
+		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
+		samsung,pin-drv = <2>;	/* 2x drive strength */
+	};
+};
+
+&pinctrl_fsys2 {
+	gpf2: gpf2 {
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		interrupt-controller;
+		#interrupt-cells = <2>;
+	};
+
+	gpf3: gpf3 {
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		interrupt-controller;
+		#interrupt-cells = <2>;
+	};
+
+	gpf4: gpf4 {
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		interrupt-controller;
+		#interrupt-cells = <2>;
+	};
+
+	gpf5: gpf5 {
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		interrupt-controller;
+		#interrupt-cells = <2>;
+	};
+
+	gpf6: gpf6 {
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		interrupt-controller;
+		#interrupt-cells = <2>;
+	};
+
+	ufs_rst_n: ufs-rst-n-pins {
+		samsung,pins = "gpf2-1";
+		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
+		samsung,pin-con-pdn = <EXYNOS_PIN_PDN_PREV>;
+	};
+
+	ufs_refclk_out: ufs-refclk-out-pins {
+		samsung,pins = "gpf2-0";
+		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
+		samsung,pin-con-pdn = <EXYNOS_PIN_PDN_PREV>;
+	};
+
+	ufs_rst_n_1: ufs-rst-n-1-pins {
+		samsung,pins = "gpf2-3";
+		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
+		samsung,pin-con-pdn = <EXYNOS_PIN_PDN_PREV>;
+	};
+
+	ufs_refclk_out_1: ufs-refclk-out-1-pins {
+		samsung,pins = "gpf2-2";
+		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
+		samsung,pin-con-pdn = <EXYNOS_PIN_PDN_PREV>;
+	};
+
+	eth0_mdc_mdio: eth0-mdc-mdio-pins {
+		samsung,pins = "gpf4-5", "gpf4-6";
+		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+	};
+
+	eth0_rgmii: eth0-rgmii-pins {
+		samsung,pins = "gpf3-1", "gpf3-2", "gpf3-3", "gpf3-4",
+			       "gpf3-5", "gpf3-6", "gpf3-7", "gpf4-0",
+			       "gpf4-1", "gpf4-2", "gpf4-3", "gpf4-4";
+		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+	};
+
+	eth0_pps_out: eth0-pps-out-pins {
+		samsung,pins = "gpf3-0";
+		samsung,pin-function = <EXYNOS_PIN_FUNC_OUTPUT>;
+		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
+	};
+
+	eth1_mdc_mdio: eth1-mdc-mdio-pins {
+		samsung,pins = "gpf6-5", "gpf6-6";
+		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+	};
+
+	eth1_rgmii: eth1-rgmii-pins {
+		samsung,pins = "gpf5-1", "gpf5-2", "gpf5-3", "gpf5-4",
+			       "gpf5-5", "gpf5-6", "gpf5-7", "gpf6-0",
+			       "gpf6-1", "gpf6-2", "gpf6-3", "gpf6-4";
+		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+	};
+
+	eth1_pps_out: eth1-pps-out-pins {
+		samsung,pins = "gpf5-0";
+		samsung,pin-function = <EXYNOS_PIN_FUNC_OUTPUT>;
+		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
+	};
+};
+
+&pinctrl_peric0 {
+	gpp0: gpp0 {
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		interrupt-controller;
+		#interrupt-cells = <2>;
+	};
+
+	gpp1: gpp1 {
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		interrupt-controller;
+		#interrupt-cells = <2>;
+	};
+
+	gpp2: gpp2 {
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		interrupt-controller;
+		#interrupt-cells = <2>;
+	};
+
+	gpg0: gpg0 {
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		interrupt-controller;
+		#interrupt-cells = <2>;
+	};
+
+	pwm_tout0: pwm-tout0-pins {
+		samsung,pins = "gpg0-0";
+		samsung,pin-function = <EXYNOS_PIN_FUNC_4>;
+		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
+	};
+
+	pwm_tout1: pwm-tout1-pins {
+		samsung,pins = "gpg0-1";
+		samsung,pin-function = <EXYNOS_PIN_FUNC_4>;
+		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
+	};
+
+	pwm_tout2: pwm-tout2-pins {
+		samsung,pins = "gpg0-2";
+		samsung,pin-function = <EXYNOS_PIN_FUNC_4>;
+		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
+	};
+
+	pwm_tout3: pwm-tout3-pins {
+		samsung,pins = "gpg0-3";
+		samsung,pin-function = <EXYNOS_PIN_FUNC_4>;
+		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
+	};
+
+	/* PERIC0 USI00  */
+	hsi2c0_bus: hsi2c0-bus-pins {
+		samsung,pins = "gpp0-0", "gpp0-1";
+		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
+	};
+
+	/* PERIC0 USI00_I2C */
+	hsi2c1_bus: hsi2c1-bus-pins {
+		samsung,pins = "gpp0-2", "gpp0-3";
+		samsung,pin-function = <EXYNOS_PIN_FUNC_3>;
+		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
+	};
+
+	/* PERIC0 USI01 */
+	hsi2c2_bus: hsi2c2-bus-pins {
+		samsung,pins = "gpp0-4", "gpp0-5";
+		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
+	};
+
+	/* PERIC0 USI01_I2C */
+	hsi2c3_bus: hsi2c3-bus-pins {
+		samsung,pins = "gpp0-6", "gpp0-7";
+		samsung,pin-function = <EXYNOS_PIN_FUNC_3>;
+		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
+	};
+
+	/* PERIC0 USI02 */
+	hsi2c4_bus: hsi2c4-bus-pins {
+		samsung,pins = "gpp1-0", "gpp1-1";
+		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
+	};
+
+	/* PERIC0 USI02_I2C */
+	hsi2c5_bus: hsi2c5-bus-pins {
+		samsung,pins = "gpp1-2", "gpp1-3";
+		samsung,pin-function = <EXYNOS_PIN_FUNC_3>;
+		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
+	};
+
+	/* PERIC0 USI03 */
+	hsi2c6_bus: hsi2c6-bus-pins {
+		samsung,pins = "gpp1-4", "gpp1-5";
+		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
+	};
+
+	/* PERIC0 USI03_I2C */
+	hsi2c7_bus: hsi2c7-bus-pins {
+		samsung,pins = "gpp1-6", "gpp1-7";
+		samsung,pin-function = <EXYNOS_PIN_FUNC_3>;
+		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
+	};
+
+	/* PERIC0 USI04 */
+	hsi2c8_bus: hsi2c8-bus-pins {
+		samsung,pins = "gpp2-0", "gpp2-1";
+		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
+	};
+
+	/* PERIC0 USI04_I2C */
+	hsi2c9_bus: hsi2c9-bus-pins {
+		samsung,pins = "gpp2-2", "gpp2-3";
+		samsung,pin-function = <EXYNOS_PIN_FUNC_3>;
+		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
+	};
+
+	/* PERIC0 USI05 */
+	hsi2c10_bus: hsi2c10-bus-pins {
+		samsung,pins = "gpp2-4", "gpp2-5";
+		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
+	};
+
+	/* PERIC0 USI05_I2C */
+	hsi2c11_bus: hsi2c11-bus-pins {
+		samsung,pins = "gpp2-6", "gpp2-7";
+		samsung,pin-function = <EXYNOS_PIN_FUNC_3>;
+		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
+	};
+
+	/* SPI USI_PERIC0_USI00_SPI */
+	spi0_bus: spi0-bus-pins {
+		samsung,pins = "gpp0-2", "gpp0-1", "gpp0-0";
+		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
+	};
+
+	spi0_cs: spi0-cs-pins {
+		samsung,pins = "gpp0-3";
+		samsung,pin-function = <EXYNOS_PIN_FUNC_OUTPUT>;
+		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
+	};
+
+	spi0_cs_func: spi0-cs-func-pins {
+		samsung,pins = "gpp0-3";
+		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
+	};
+
+	/* PERIC0 USI01_SPI */
+	spi1_bus: spi1-bus-pins {
+		samsung,pins = "gpp0-6", "gpp0-5", "gpp0-4";
+		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
+	};
+
+	spi1_cs: spi1-cs-pins {
+		samsung,pins = "gpp0-7";
+		samsung,pin-function = <EXYNOS_PIN_FUNC_OUTPUT>;
+		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
+	};
+
+	spi1_cs_func: spi1-cs-func-pins {
+		samsung,pins = "gpp0-7";
+		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
+	};
+
+	/* PERIC0 USI02_SPI */
+	spi2_bus: spi2-bus-pins {
+		samsung,pins = "gpp1-2", "gpp1-1", "gpp1-0";
+		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
+	};
+
+	spi2_cs: spi2-cs-pins {
+		samsung,pins = "gpp1-3";
+		samsung,pin-function = <EXYNOS_PIN_FUNC_OUTPUT>;
+		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
+	};
+
+	spi2_cs_func: spi2-cs-func-pins {
+		samsung,pins = "gpp1-3";
+		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
+	};
+
+	/* PERIC0 USI03_SPI */
+	spi3_bus: spi3-bus-pins {
+		samsung,pins = "gpp1-6", "gpp1-5", "gpp1-4";
+		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
+	};
+
+	spi3_cs: spi3-cs-pins {
+		samsung,pins = "gpp1-7";
+		samsung,pin-function = <EXYNOS_PIN_FUNC_OUTPUT>;
+		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
+	};
+
+	spi3_cs_func: spi3-cs-func-pins {
+		samsung,pins = "gpp1-7";
+		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
+	};
+
+	/* PERIC0 USI04_SPI */
+	spi4_bus: spi4-bus-pins {
+		samsung,pins = "gpp2-2", "gpp2-1", "gpp2-0";
+		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
+	};
+
+	spi4_cs: spi4-cs-pins {
+		samsung,pins = "gpp2-3";
+		samsung,pin-function = <EXYNOS_PIN_FUNC_OUTPUT>;
+		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
+	};
+
+	spi4_cs_func: spi4-cs-func-pins {
+		samsung,pins = "gpp2-3";
+		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
+	};
+
+	/* PERIC0 USI05_SPI */
+	spi5_bus: spi5-bus-pins {
+		samsung,pins = "gpp2-6", "gpp2-5", "gpp2-4";
+		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
+	};
+
+	spi5_cs: spi5-cs-pins {
+		samsung,pins = "gpp2-7";
+		samsung,pin-function = <EXYNOS_PIN_FUNC_OUTPUT>;
+		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
+	};
+
+	spi5_cs_func: spi5-cs-func-pins {
+		samsung,pins = "gpp2-7";
+		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
+	};
+
+	/* USI_PERIC0_USI00_UART */
+	uart0_bus: uart0-bus-pins {
+		samsung,pins = "gpp0-0", "gpp0-1", "gpp0-2", "gpp0-3";
+		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
+	};
+
+	uart0_bus_dual: uart0-bus-dual-pins {
+		samsung,pins = "gpp0-0", "gpp0-1";
+		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
+	};
+
+	/* USI_PERIC0_USI01_UART */
+	uart1_bus: uart1-bus-pins {
+		samsung,pins = "gpp0-4", "gpp0-5", "gpp0-6", "gpp0-7";
+		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
+	};
+
+	uart1_bus_dual: uart1-bus-dual-pins {
+		samsung,pins = "gpp0-4", "gpp0-5";
+		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
+	};
+
+	/* USI_PERIC0_USI02_UART */
+	uart2_bus: uart2-bus-pins {
+		samsung,pins = "gpp1-0", "gpp1-1", "gpp1-2", "gpp1-3";
+		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
+	};
+
+	uart2_bus_dual: uart2-bus-dual-pins {
+		samsung,pins = "gpp1-0", "gpp1-1";
+		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
+	};
+
+	/* USI_PERIC0_USI03_UART */
+	uart3_bus: uart3-bus-pins {
+		samsung,pins = "gpp1-4", "gpp1-5", "gpp1-6", "gpp1-7";
+		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
+	};
+
+	uart3_bus_dual: uart3-bus-dual-pins {
+		samsung,pins = "gpp1-4", "gpp1-5";
+		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
+	};
+
+	/* USI_PERIC0_USI04_UART */
+	uart4_bus: uart4-bus-pins {
+		samsung,pins = "gpp2-0", "gpp2-1", "gpp2-2", "gpp2-3";
+		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
+	};
+
+	uart4_bus_dual: uart4-bus-dual-pins {
+		samsung,pins = "gpp2-0", "gpp2-1";
+		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
+	};
+
+	/* USI_PERIC0_USI05_UART */
+	uart5_bus: uart5-bus-pins {
+		samsung,pins = "gpp2-4", "gpp2-5", "gpp2-6", "gpp2-7";
+		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
+	};
+
+	uart5_bus_dual: uart5-bus-dual-pins {
+		samsung,pins = "gpp2-4", "gpp2-5";
+		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
+	};
+};
+
+&pinctrl_peric1 {
+	gpp3: gpp3 {
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		interrupt-controller;
+		#interrupt-cells = <2>;
+	};
+
+	gpp4: gpp4 {
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		interrupt-controller;
+		#interrupt-cells = <2>;
+	};
+
+	gpp5: gpp5 {
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		interrupt-controller;
+		#interrupt-cells = <2>;
+	};
+
+	gpg1: gpg1 {
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		interrupt-controller;
+		#interrupt-cells = <2>;
+	};
+
+	gpg2: gpg2 {
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		interrupt-controller;
+		#interrupt-cells = <2>;
+	};
+
+	gpg3: gpg3 {
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		interrupt-controller;
+		#interrupt-cells = <2>;
+	};
+
+	/* PERIC1 USI06 */
+	hsi2c12_bus: hsi2c12-bus-pins {
+		samsung,pins = "gpp3-0", "gpp3-1";
+		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
+		samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV1>;
+	};
+
+	/* PERIC1 USI06_I2C */
+	hsi2c13_bus: hsi2c13-bus-pins {
+		samsung,pins = "gpp3-2", "gpp3-3";
+		samsung,pin-function = <EXYNOS_PIN_FUNC_3>;
+		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
+		samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV1>;
+	};
+
+	/* PERIC1 USI07 */
+	hsi2c14_bus: hsi2c14-bus-pins {
+		samsung,pins = "gpp3-4", "gpp3-5";
+		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
+		samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV1>;
+	};
+
+	/* PERIC1 USI07_I2C */
+	hsi2c15_bus: hsi2c15-bus-pins {
+		samsung,pins = "gpp3-6", "gpp3-7";
+		samsung,pin-function = <EXYNOS_PIN_FUNC_3>;
+		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
+		samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV1>;
+	};
+
+	/* PERIC1 USI08 */
+	hsi2c16_bus: hsi2c16-bus-pins {
+		samsung,pins = "gpp4-0", "gpp4-1";
+		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
+		samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV1>;
+	};
+
+	/* PERIC1 USI08_I2C */
+	hsi2c17_bus: hsi2c17-bus-pins {
+		samsung,pins = "gpp4-2", "gpp4-3";
+		samsung,pin-function = <EXYNOS_PIN_FUNC_3>;
+		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
+		samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV1>;
+	};
+
+	/* PERIC1 USI09 */
+	hsi2c18_bus: hsi2c18-bus-pins {
+		samsung,pins = "gpp4-4", "gpp4-5";
+		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
+		samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV1>;
+	};
+
+	/* PERIC1 USI09_I2C */
+	hsi2c19_bus: hsi2c19-bus-pins {
+		samsung,pins = "gpp4-6", "gpp4-7";
+		samsung,pin-function = <EXYNOS_PIN_FUNC_3>;
+		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
+		samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV1>;
+	};
+
+	/* PERIC1 USI10 */
+	hsi2c20_bus: hsi2c20-bus-pins {
+		samsung,pins = "gpp5-0", "gpp5-1";
+		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
+		samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV1>;
+	};
+
+	/* PERIC1 USI10_I2C */
+	hsi2c21_bus: hsi2c21-bus-pins {
+		samsung,pins = "gpp5-2", "gpp5-3";
+		samsung,pin-function = <EXYNOS_PIN_FUNC_3>;
+		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
+		samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV1>;
+	};
+
+	/* PERIC1 USI11 */
+	hsi2c22_bus: hsi2c22-bus-pins {
+		samsung,pins = "gpp5-4", "gpp5-5";
+		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
+		samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV1>;
+	};
+
+	/* PERIC1 USI11_I2C */
+	hsi2c23_bus: hsi2c23-bus-pins {
+		samsung,pins = "gpp5-6", "gpp5-7";
+		samsung,pin-function = <EXYNOS_PIN_FUNC_3>;
+		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
+		samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV1>;
+	};
+
+	/* PERIC1 USI06_SPI */
+	spi6_bus: spi6-bus-pins {
+		samsung,pins = "gpp3-2", "gpp3-1", "gpp3-0";
+		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
+		samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV1>;
+	};
+
+	spi6_cs: spi6-cs-pins {
+		samsung,pins = "gpp3-3";
+		samsung,pin-function = <EXYNOS_PIN_FUNC_OUTPUT>;
+		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
+		samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV1>;
+	};
+
+	spi6_cs_func: spi6-cs-func-pins {
+		samsung,pins = "gpp3-3";
+		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
+		samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV1>;
+	};
+
+	/* PERIC1 USI07_SPI */
+	spi7_bus: spi7-bus-pins {
+		samsung,pins = "gpp3-6", "gpp3-5", "gpp3-4";
+		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
+		samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV1>;
+	};
+
+	spi7_cs: spi7-cs-pins {
+		samsung,pins = "gpp3-7";
+		samsung,pin-function = <EXYNOS_PIN_FUNC_OUTPUT>;
+		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
+		samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV1>;
+	};
+
+	spi7_cs_func: spi7-cs-func-pins {
+		samsung,pins = "gpp3-7";
+		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
+		samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV1>;
+	};
+
+	/* PERIC1 USI08_SPI */
+	spi8_bus: spi8-bus-pins {
+		samsung,pins = "gpp4-2", "gpp4-1", "gpp4-0";
+		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
+		samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV1>;
+	};
+
+	spi8_cs: spi8-cs-pins {
+		samsung,pins = "gpp4-3";
+		samsung,pin-function = <EXYNOS_PIN_FUNC_OUTPUT>;
+		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
+		samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV1>;
+	};
+
+	spi8_cs_func: spi8-cs-func-pins {
+		samsung,pins = "gpp4-3";
+		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
+		samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV1>;
+	};
+
+	/* PERIC1 USI09_SPI */
+	spi9_bus: spi9-bus-pins {
+		samsung,pins = "gpp4-6", "gpp4-5", "gpp4-4";
+		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
+		samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV1>;
+	};
+
+	spi9_cs: spi9-cs-pins {
+		samsung,pins = "gpp4-7";
+		samsung,pin-function = <EXYNOS_PIN_FUNC_OUTPUT>;
+		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
+		samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV1>;
+	};
+
+	spi9_cs_func: spi9-cs-func-pins {
+		samsung,pins = "gpp4-7";
+		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
+		samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV1>;
+	};
+
+	/* PERIC1 USI10_SPI */
+	spi10_bus: spi10-pins {
+		samsung,pins = "gpp5-2", "gpp5-1", "gpp5-0";
+		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
+		samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV1>;
+	};
+
+	spi10_cs: spi10-cs-pins {
+		samsung,pins = "gpp5-3";
+		samsung,pin-function = <EXYNOS_PIN_FUNC_OUTPUT>;
+		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
+		samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV1>;
+	};
+
+	spi10_cs_func: spi10-cs-func-pins {
+		samsung,pins = "gpp5-3";
+		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
+		samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV1>;
+	};
+
+	/* PERIC1 USI11_SPI */
+	spi11_bus: spi11-pins {
+		samsung,pins = "gpp3-6", "gpp3-5", "gpp3-4";
+		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
+		samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV1>;
+	};
+
+	spi11_cs: spi11-cs-pins {
+		samsung,pins = "gpp3-7";
+		samsung,pin-function = <EXYNOS_PIN_FUNC_OUTPUT>;
+		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
+		samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV1>;
+	};
+
+	spi11_cs_func: spi11-cs-func-pins {
+		samsung,pins = "gpp3-7";
+		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
+		samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV1>;
+	};
+
+	/* USI_PERIC1_USI06_UART */
+	uart6_bus: uart6-bus-pins {
+		samsung,pins = "gpp3-3", "gpp3-2", "gpp3-1", "gpp3-0";
+		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
+	};
+
+	uart6_bus_dual: uart6-bus-dual-pins {
+		samsung,pins = "gpp3-0", "gpp3-1";
+		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
+	};
+
+	/* USI_PERIC1_USI07_UART */
+	uart7_bus: uart7-bus-pins {
+		samsung,pins = "gpp3-7", "gpp3-6", "gpp3-5", "gpp3-4";
+		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
+	};
+
+	uart7_bus_dual: uart7-bus-dual-pins {
+		samsung,pins = "gpp3-4", "gpp3-5";
+		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
+	};
+
+	/* USI_PERIC1_USI08_UART */
+	uart8_bus: uart8-bus-pins {
+		samsung,pins = "gpp4-3", "gpp4-2", "gpp4-1", "gpp4-0";
+		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
+	};
+
+	uart8_bus_dual: uart8-bus-dual-pins {
+		samsung,pins = "gpp4-0", "gpp4-1";
+		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
+	};
+
+	/* USI_PERIC1_USI09_UART */
+	uart9_bus: uart9-bus-pins {
+		samsung,pins = "gpp4-7", "gpp4-6", "gpp4-5", "gpp4-4";
+		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
+	};
+
+	uart9_bus_dual: uart9-bus-dual-pins {
+		samsung,pins = "gpp4-4", "gpp4-5";
+		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
+	};
+
+	/* USI_PERIC1_USI10_UART */
+	uart10_bus: uart10-bus-pins {
+		samsung,pins = "gpp5-3", "gpp5-2", "gpp5-1", "gpp5-0";
+		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
+	};
+
+	uart10_bus_dual: uart10-bus-dual-pins {
+		samsung,pins = "gpp5-0", "gpp5-1";
+		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
+	};
+
+	/* USI_PERIC1_USI11_UART */
+	uart11_bus: uart11-bus-pins {
+		samsung,pins = "gpp5-7", "gpp5-6", "gpp5-5", "gpp5-4";
+		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
+	};
+
+	uart11_bus_dual: uart11-bus-dual-pins {
+		samsung,pins = "gpp5-4", "gpp5-5";
+		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
+	};
+};
diff --git a/arch/arm64/boot/dts/exynos/exynosautov9-sadk.dts b/arch/arm64/boot/dts/exynos/exynosautov9-sadk.dts
new file mode 100644
index 000000000000..ef46d7aa6e28
--- /dev/null
+++ b/arch/arm64/boot/dts/exynos/exynosautov9-sadk.dts
@@ -0,0 +1,56 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Samsung ExynosAutov9 SADK board device tree source
+ *
+ * Copyright (c) 2021 Samsung Electronics Co., Ltd.
+ *
+ */
+
+/dts-v1/;
+#include "exynosautov9.dtsi"
+#include <dt-bindings/gpio/gpio.h>
+
+/ {
+	model = "Samsung ExynosAuto v9 SADK board";
+	compatible = "samsung,exynosautov9-sadk", "samsung,exynosautov9";
+
+	#address-cells = <2>;
+	#size-cells = <2>;
+
+	aliases {
+		serial0 = &serial_0;
+	};
+
+	chosen {
+		stdout-path = &serial_0;
+	};
+
+	memory@80000000 {
+		device_type = "memory";
+		reg = <0x0 0x80000000 0x0 0x77000000>,
+		      <0x8 0x80000000 0x1 0x7ba00000>,
+		      <0xa 0x00000000 0x2 0x00000000>;
+	};
+
+	ufs_0_fixed_vcc_reg: regulator-0 {
+		compatible = "regulator-fixed";
+		regulator-name = "ufs-vcc";
+		gpio = <&gpq0 1 GPIO_ACTIVE_HIGH>;
+		regulator-boot-on;
+		enable-active-high;
+	};
+};
+
+&serial_0 {
+	status = "okay";
+};
+
+&ufs_0_phy {
+	status = "okay";
+};
+
+&ufs_0 {
+	status = "okay";
+	vcc-supply = <&ufs_0_fixed_vcc_reg>;
+	vcc-fixed-regulator;
+};
diff --git a/arch/arm64/boot/dts/exynos/exynosautov9.dtsi b/arch/arm64/boot/dts/exynos/exynosautov9.dtsi
new file mode 100644
index 000000000000..3e4727344b4a
--- /dev/null
+++ b/arch/arm64/boot/dts/exynos/exynosautov9.dtsi
@@ -0,0 +1,306 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Samsung's ExynosAuto v9 SoC device tree source
+ *
+ * Copyright (c) 2021 Samsung Electronics Co., Ltd.
+ *
+ */
+
+#include <dt-bindings/interrupt-controller/arm-gic.h>
+
+/ {
+	compatible = "samsung,exynosautov9";
+	#address-cells = <2>;
+	#size-cells = <1>;
+
+	interrupt-parent = <&gic>;
+
+	aliases {
+		pinctrl0 = &pinctrl_alive;
+		pinctrl1 = &pinctrl_aud;
+		pinctrl2 = &pinctrl_fsys0;
+		pinctrl3 = &pinctrl_fsys1;
+		pinctrl4 = &pinctrl_fsys2;
+		pinctrl5 = &pinctrl_peric0;
+		pinctrl6 = &pinctrl_peric1;
+	};
+
+	arm-pmu {
+		compatible = "arm,cortex-a76-pmu";
+		interrupts = <GIC_SPI 84 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 85 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 86 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 87 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 107 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 108 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 109 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 110 IRQ_TYPE_LEVEL_HIGH>;
+		interrupt-affinity = <&cpu0>, <&cpu1>, <&cpu2>, <&cpu3>,
+				     <&cpu4>, <&cpu5>, <&cpu6>, <&cpu7>;
+	};
+
+	cpus {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		cpu-map {
+			cluster0 {
+				core0 {
+					cpu = <&cpu0>;
+				};
+				core1 {
+					cpu = <&cpu1>;
+				};
+				core2 {
+					cpu = <&cpu2>;
+				};
+				core3 {
+					cpu = <&cpu3>;
+				};
+			};
+
+			cluster1 {
+				core0 {
+					cpu = <&cpu4>;
+				};
+				core1 {
+					cpu = <&cpu5>;
+				};
+				core2 {
+					cpu = <&cpu6>;
+				};
+				core3 {
+					cpu = <&cpu7>;
+				};
+			};
+		};
+
+		cpu0: cpu@0 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a76";
+			reg = <0x0>;
+			enable-method = "psci";
+		};
+
+		cpu1: cpu@100 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a76";
+			reg = <0x100>;
+			enable-method = "psci";
+		};
+
+		cpu2: cpu@200 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a76";
+			reg = <0x200>;
+			enable-method = "psci";
+		};
+
+		cpu3: cpu@300 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a76";
+			reg = <0x300>;
+			enable-method = "psci";
+		};
+
+		cpu4: cpu@10000 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a76";
+			reg = <0x10000>;
+			enable-method = "psci";
+		};
+
+		cpu5: cpu@10100 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a76";
+			reg = <0x10100>;
+			enable-method = "psci";
+		};
+
+		cpu6: cpu@10200 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a76";
+			reg = <0x10200>;
+			enable-method = "psci";
+		};
+
+		cpu7: cpu@10300 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a76";
+			reg = <0x10300>;
+			enable-method = "psci";
+		};
+	};
+
+	psci {
+		compatible = "arm,psci-1.0";
+		method = "smc";
+		cpu_suspend = <0xc4000001>;
+		cpu_off = <0x84000002>;
+		cpu_on = <0xc4000003>;
+	};
+
+	timer {
+		compatible = "arm,armv8-timer";
+		interrupts = <GIC_PPI 13 (GIC_CPU_MASK_SIMPLE(8) | IRQ_TYPE_LEVEL_LOW)>,
+			     <GIC_PPI 14 (GIC_CPU_MASK_SIMPLE(8) | IRQ_TYPE_LEVEL_LOW)>,
+			     <GIC_PPI 11 (GIC_CPU_MASK_SIMPLE(8) | IRQ_TYPE_LEVEL_LOW)>,
+			     <GIC_PPI 10 (GIC_CPU_MASK_SIMPLE(8) | IRQ_TYPE_LEVEL_LOW)>;
+	};
+
+	fixed-rate-clocks {
+		xtcxo: clock {
+			compatible = "fixed-clock";
+			#clock-cells = <0>;
+			clock-frequency = <26000000>;
+			clock-output-names = "oscclk";
+		};
+
+		/*
+		 * Keep the stub clock for serial driver, until proper clock
+		 * driver is implemented.
+		 */
+		uart_clock: uart-clock {
+			compatible = "fixed-clock";
+			#clock-cells = <0>;
+			clock-frequency = <133250000>;
+			clock-output-names = "uart";
+		};
+
+		/*
+		 * Keep the stub clock for ufs driver, until proper clock
+		 * driver is implemented.
+		 */
+		ufs_core_clock: ufs-core-clock {
+			compatible = "fixed-clock";
+			#clock-cells = <0>;
+			clock-frequency = <166562500>;
+		};
+	};
+
+	soc: soc@0 {
+		compatible = "simple-bus";
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges = <0x0 0x0 0x0 0x20000000>;
+
+		chipid@10000000 {
+			compatible = "samsung,exynos850-chipid";
+			reg = <0x10000000 0x24>;
+		};
+
+		gic: interrupt-controller@10101000 {
+			compatible = "arm,gic-400";
+			#interrupt-cells = <3>;
+			#address-cells = <0>;
+			interrupt-controller;
+			reg = <0x10101000 0x1000>,
+			      <0x10102000 0x2000>,
+			      <0x10104000 0x2000>,
+			      <0x10106000 0x2000>;
+			interrupts = <GIC_PPI 9 (GIC_CPU_MASK_SIMPLE(8) |
+						 IRQ_TYPE_LEVEL_HIGH)>;
+		};
+
+		pinctrl_alive: pinctrl@10450000 {
+			compatible = "samsung,exynosautov9-pinctrl";
+			reg = <0x10450000 0x1000>;
+
+			wakeup-interrupt-controller {
+				compatible = "samsung,exynos7-wakeup-eint";
+			};
+		};
+
+		pinctrl_aud: pinctrl@19c60000{
+			compatible = "samsung,exynosautov9-pinctrl";
+			reg = <0x19c60000 0x1000>;
+		};
+
+		pinctrl_fsys0: pinctrl@17740000 {
+			compatible = "samsung,exynosautov9-pinctrl";
+			reg = <0x17740000 0x1000>;
+			interrupts = <GIC_SPI 163 IRQ_TYPE_LEVEL_HIGH>;
+		};
+
+		pinctrl_fsys1: pinctrl@17060000 {
+			compatible = "samsung,exynosautov9-pinctrl";
+			reg = <0x17060000 0x1000>;
+			interrupts = <GIC_SPI 188 IRQ_TYPE_LEVEL_HIGH>;
+		};
+
+		pinctrl_fsys2: pinctrl@17c30000 {
+			compatible = "samsung,exynosautov9-pinctrl";
+			reg = <0x17c30000 0x1000>;
+			interrupts = <GIC_SPI 217 IRQ_TYPE_LEVEL_HIGH>;
+		};
+
+		pinctrl_peric0: pinctrl@10230000 {
+			compatible = "samsung,exynosautov9-pinctrl";
+			reg = <0x10230000 0x1000>;
+			interrupts = <GIC_SPI 338 IRQ_TYPE_LEVEL_HIGH>;
+		};
+
+		pinctrl_peric1: pinctrl@10830000 {
+			compatible = "samsung,exynosautov9-pinctrl";
+			reg = <0x10830000 0x1000>;
+			interrupts = <GIC_SPI 356 IRQ_TYPE_LEVEL_HIGH>;
+		};
+
+		pmu_system_controller: system-controller@10460000 {
+			compatible = "samsung,exynos7-pmu", "syscon";
+			reg = <0x10460000 0x10000>;
+		};
+
+		syscon_fsys2: syscon@17c20000 {
+			compatible = "samsung,exynosautov9-sysreg", "syscon";
+			reg = <0x17c20000 0x1000>;
+		};
+
+		/* USI: UART */
+		serial_0: uart@10300000 {
+			compatible = "samsung,exynos850-uart";
+			reg = <0x10300000 0x100>;
+			interrupts = <GIC_SPI 345 IRQ_TYPE_LEVEL_HIGH>;
+			pinctrl-names = "default";
+			pinctrl-0 = <&uart0_bus_dual>;
+			clocks = <&uart_clock>, <&uart_clock>;
+			clock-names = "uart", "clk_uart_baud0";
+			status = "disabled";
+		};
+
+		ufs_0_phy: ufs0-phy@17e04000 {
+			compatible = "samsung,exynosautov9-ufs-phy";
+			reg = <0x17e04000 0xc00>;
+			reg-names = "phy-pma";
+			samsung,pmu-syscon = <&pmu_system_controller>;
+			#phy-cells = <0>;
+			clocks = <&xtcxo>;
+			clock-names = "ref_clk";
+			status = "disabled";
+		};
+
+		ufs_0: ufs0@17e00000 {
+			compatible ="samsung,exynosautov9-ufs";
+
+			reg = <0x17e00000 0x100>,  /* 0: HCI standard */
+				<0x17e01100 0x410>,  /* 1: Vendor-specific */
+				<0x17e80000 0x8000>,  /* 2: UNIPRO */
+				<0x17dc0000 0x2200>;  /* 3: UFS protector */
+			reg-names = "hci", "vs_hci", "unipro", "ufsp";
+			interrupts = <GIC_SPI 227 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&ufs_core_clock>,
+				<&ufs_core_clock>;
+			clock-names = "core_clk", "sclk_unipro_main";
+			freq-table-hz = <0 0>, <0 0>;
+			pinctrl-names = "default";
+			pinctrl-0 = <&ufs_rst_n &ufs_refclk_out>;
+			phys = <&ufs_0_phy>;
+			phy-names = "ufs-phy";
+			samsung,sysreg = <&syscon_fsys2>;
+			samsung,ufs-shareability-reg-offset = <0x710>;
+			status = "disabled";
+		};
+	};
+};
+
+#include "exynosautov9-pinctrl.dtsi"
diff --git a/arch/arm64/boot/dts/freescale/Makefile b/arch/arm64/boot/dts/freescale/Makefile
index db9e36ebe932..a14a6173b765 100644
--- a/arch/arm64/boot/dts/freescale/Makefile
+++ b/arch/arm64/boot/dts/freescale/Makefile
@@ -25,6 +25,8 @@ dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-ls2080a-rdb.dtb
 dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-ls2080a-simu.dtb
 dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-ls2088a-qds.dtb
 dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-ls2088a-rdb.dtb
+dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-lx2160a-bluebox3.dtb
+dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-lx2160a-bluebox3-rev-a.dtb
 dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-lx2160a-clearfog-cx.dtb
 dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-lx2160a-honeycomb.dtb
 dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-lx2160a-qds.dtb
@@ -70,4 +72,6 @@ dtb-$(CONFIG_ARCH_MXC) += imx8qxp-ai_ml.dtb
 dtb-$(CONFIG_ARCH_MXC) += imx8qxp-colibri-eval-v3.dtb
 dtb-$(CONFIG_ARCH_MXC) += imx8qxp-mek.dtb
 
+dtb-$(CONFIG_ARCH_S32) += s32g274a-evb.dtb
+dtb-$(CONFIG_ARCH_S32) += s32g274a-rdb2.dtb
 dtb-$(CONFIG_ARCH_S32) += s32v234-evb.dtb
diff --git a/arch/arm64/boot/dts/freescale/fsl-ls1012a-rdb.dts b/arch/arm64/boot/dts/freescale/fsl-ls1012a-rdb.dts
index 79f155dedb2d..e662677a6e28 100644
--- a/arch/arm64/boot/dts/freescale/fsl-ls1012a-rdb.dts
+++ b/arch/arm64/boot/dts/freescale/fsl-ls1012a-rdb.dts
@@ -15,6 +15,7 @@
 	compatible = "fsl,ls1012a-rdb", "fsl,ls1012a";
 
 	aliases {
+		serial0 = &duart0;
 		mmc0 = &esdhc0;
 		mmc1 = &esdhc1;
 	};
diff --git a/arch/arm64/boot/dts/freescale/fsl-ls1028a-kontron-sl28-var1.dts b/arch/arm64/boot/dts/freescale/fsl-ls1028a-kontron-sl28-var1.dts
index e8d31279b7a3..7cd29ab970d9 100644
--- a/arch/arm64/boot/dts/freescale/fsl-ls1028a-kontron-sl28-var1.dts
+++ b/arch/arm64/boot/dts/freescale/fsl-ls1028a-kontron-sl28-var1.dts
@@ -8,7 +8,7 @@
  * None of the  four SerDes lanes are used by the module, instead they are
  * all led out to the carrier for customer use.
  *
- * Copyright (C) 2020 Michael Walle <michael@walle.cc>
+ * Copyright (C) 2021 Michael Walle <michael@walle.cc>
  *
  */
 
@@ -21,43 +21,39 @@
 	compatible = "kontron,sl28-var1", "kontron,sl28", "fsl,ls1028a";
 };
 
+&enetc_mdio_pf3 {
+	/* Delete unused phy node */
+	/delete-node/ ethernet-phy@5;
+
+	phy0: ethernet-phy@4 {
+		reg = <0x4>;
+		eee-broken-1000t;
+		eee-broken-100tx;
+		qca,clk-out-frequency = <125000000>;
+		qca,clk-out-strength = <AR803X_STRENGTH_FULL>;
+		qca,keep-pll-enabled;
+		vddio-supply = <&vddio>;
+
+		vddio: vddio-regulator {
+			regulator-name = "VDDIO";
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+		};
+
+		vddh: vddh-regulator {
+			regulator-name = "VDDH";
+		};
+	};
+};
+
 &enetc_port0 {
 	status = "disabled";
-	/*
-	 * Delete both the phy-handle to the old phy0 label as well as
-	 * the mdio node with the old phy node with the old phy0 label.
-	 */
+	/* Delete the phy-handle to the old phy0 label */
 	/delete-property/ phy-handle;
-	/delete-node/ mdio;
 };
 
 &enetc_port1 {
 	phy-handle = <&phy0>;
-	phy-connection-type = "rgmii-id";
+	phy-mode = "rgmii-id";
 	status = "okay";
-
-	mdio {
-		#address-cells = <1>;
-		#size-cells = <0>;
-
-		phy0: ethernet-phy@4 {
-			reg = <0x4>;
-			eee-broken-1000t;
-			eee-broken-100tx;
-			qca,clk-out-frequency = <125000000>;
-			qca,clk-out-strength = <AR803X_STRENGTH_FULL>;
-			qca,keep-pll-enabled;
-			vddio-supply = <&vddio>;
-
-			vddio: vddio-regulator {
-				regulator-name = "VDDIO";
-				regulator-min-microvolt = <1800000>;
-				regulator-max-microvolt = <1800000>;
-			};
-
-			vddh: vddh-regulator {
-				regulator-name = "VDDH";
-			};
-		};
-	};
 };
diff --git a/arch/arm64/boot/dts/freescale/fsl-ls1028a-kontron-sl28-var2.dts b/arch/arm64/boot/dts/freescale/fsl-ls1028a-kontron-sl28-var2.dts
index f6a79c8080d1..330e34f933a3 100644
--- a/arch/arm64/boot/dts/freescale/fsl-ls1028a-kontron-sl28-var2.dts
+++ b/arch/arm64/boot/dts/freescale/fsl-ls1028a-kontron-sl28-var2.dts
@@ -5,7 +5,7 @@
  * This is for the network variant 2 which has two ethernet ports. These
  * ports are connected to the internal switch.
  *
- * Copyright (C) 2020 Michael Walle <michael@walle.cc>
+ * Copyright (C) 2021 Michael Walle <michael@walle.cc>
  *
  */
 
@@ -18,12 +18,6 @@
 };
 
 &enetc_mdio_pf3 {
-	phy0: ethernet-phy@5 {
-		reg = <0x5>;
-		eee-broken-1000t;
-		eee-broken-100tx;
-	};
-
 	phy1: ethernet-phy@4 {
 		reg = <0x4>;
 		eee-broken-1000t;
@@ -34,14 +28,11 @@
 &enetc_port0 {
 	status = "disabled";
 	/*
-	 * In the base device tree the PHY was registered in the mdio
-	 * subnode as it is PHY for this port. On this module this PHY
-	 * is connected to a switch port instead and registered above.
-	 * Therefore, delete the mdio subnode as well as the phy-handle
-	 * property here.
+	 * In the base device tree the PHY at address 5 was assigned for
+	 * this port. On this module this PHY is connected to a switch
+	 * port instead. Therefore, delete the phy-handle property here.
 	 */
 	/delete-property/ phy-handle;
-	/delete-node/ mdio;
 };
 
 &enetc_port2 {
diff --git a/arch/arm64/boot/dts/freescale/fsl-ls1028a-kontron-sl28-var4.dts b/arch/arm64/boot/dts/freescale/fsl-ls1028a-kontron-sl28-var4.dts
index e65d1c477e2c..9b5e92fb753e 100644
--- a/arch/arm64/boot/dts/freescale/fsl-ls1028a-kontron-sl28-var4.dts
+++ b/arch/arm64/boot/dts/freescale/fsl-ls1028a-kontron-sl28-var4.dts
@@ -5,7 +5,7 @@
  * This is for the network variant 4 which has two ethernet ports. It
  * extends the base and provides one more port connected via RGMII.
  *
- * Copyright (C) 2019 Michael Walle <michael@walle.cc>
+ * Copyright (C) 2021 Michael Walle <michael@walle.cc>
  *
  */
 
@@ -18,33 +18,30 @@
 	compatible = "kontron,sl28-var4", "kontron,sl28", "fsl,ls1028a";
 };
 
-&enetc_port1 {
-	phy-handle = <&phy1>;
-	phy-connection-type = "rgmii-id";
-	status = "okay";
+&enetc_mdio_pf3 {
+	phy1: ethernet-phy@4 {
+		reg = <0x4>;
+		eee-broken-1000t;
+		eee-broken-100tx;
+		qca,clk-out-frequency = <125000000>;
+		qca,clk-out-strength = <AR803X_STRENGTH_FULL>;
+		qca,keep-pll-enabled;
+		vddio-supply = <&vddio>;
 
-	mdio {
-		#address-cells = <1>;
-		#size-cells = <0>;
-
-		phy1: ethernet-phy@4 {
-			reg = <0x4>;
-			eee-broken-1000t;
-			eee-broken-100tx;
-			qca,clk-out-frequency = <125000000>;
-			qca,clk-out-strength = <AR803X_STRENGTH_FULL>;
-			qca,keep-pll-enabled;
-			vddio-supply = <&vddio>;
-
-			vddio: vddio-regulator {
-				regulator-name = "VDDIO";
-				regulator-min-microvolt = <1800000>;
-				regulator-max-microvolt = <1800000>;
-			};
+		vddio: vddio-regulator {
+			regulator-name = "VDDIO";
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+		};
 
-			vddh: vddh-regulator {
-				regulator-name = "VDDH";
-			};
+		vddh: vddh-regulator {
+			regulator-name = "VDDH";
 		};
 	};
 };
+
+&enetc_port1 {
+	phy-handle = <&phy1>;
+	phy-mode = "rgmii-id";
+	status = "okay";
+};
diff --git a/arch/arm64/boot/dts/freescale/fsl-ls1028a-kontron-sl28.dts b/arch/arm64/boot/dts/freescale/fsl-ls1028a-kontron-sl28.dts
index a92ecb331cdc..d74e738e4070 100644
--- a/arch/arm64/boot/dts/freescale/fsl-ls1028a-kontron-sl28.dts
+++ b/arch/arm64/boot/dts/freescale/fsl-ls1028a-kontron-sl28.dts
@@ -2,7 +2,7 @@
 /*
  * Device Tree file for the Kontron SMARC-sAL28 board.
  *
- * Copyright (C) 2019 Michael Walle <michael@walle.cc>
+ * Copyright (C) 2021 Michael Walle <michael@walle.cc>
  *
  */
 
@@ -80,22 +80,19 @@
 	status = "okay";
 };
 
+&enetc_mdio_pf3 {
+	phy0: ethernet-phy@5 {
+		reg = <0x5>;
+		eee-broken-1000t;
+		eee-broken-100tx;
+	};
+};
+
 &enetc_port0 {
 	phy-handle = <&phy0>;
-	phy-connection-type = "sgmii";
+	phy-mode = "sgmii";
 	managed = "in-band-status";
 	status = "okay";
-
-	mdio {
-		#address-cells = <1>;
-		#size-cells = <0>;
-
-		phy0: ethernet-phy@5 {
-			reg = <0x5>;
-			eee-broken-1000t;
-			eee-broken-100tx;
-		};
-	};
 };
 
 &esdhc {
@@ -309,3 +306,11 @@
 &lpuart1 {
 	status = "okay";
 };
+
+&usb0 {
+	status = "okay";
+};
+
+&usb1 {
+	status = "okay";
+};
diff --git a/arch/arm64/boot/dts/freescale/fsl-ls1028a-qds.dts b/arch/arm64/boot/dts/freescale/fsl-ls1028a-qds.dts
index bfd14b64567e..6e2a1da662fb 100644
--- a/arch/arm64/boot/dts/freescale/fsl-ls1028a-qds.dts
+++ b/arch/arm64/boot/dts/freescale/fsl-ls1028a-qds.dts
@@ -320,7 +320,7 @@
 
 &enetc_port1 {
 	phy-handle = <&qds_phy1>;
-	phy-connection-type = "rgmii-id";
+	phy-mode = "rgmii-id";
 	status = "okay";
 };
 
@@ -335,3 +335,11 @@
 &sata {
 	status = "okay";
 };
+
+&usb0 {
+	status = "okay";
+};
+
+&usb1 {
+	status = "okay";
+};
diff --git a/arch/arm64/boot/dts/freescale/fsl-ls1028a-rdb.dts b/arch/arm64/boot/dts/freescale/fsl-ls1028a-rdb.dts
index d7b527272500..7719f44bcaed 100644
--- a/arch/arm64/boot/dts/freescale/fsl-ls1028a-rdb.dts
+++ b/arch/arm64/boot/dts/freescale/fsl-ls1028a-rdb.dts
@@ -197,6 +197,10 @@
 };
 
 &enetc_mdio_pf3 {
+	sgmii_phy0: ethernet-phy@2 {
+		reg = <0x2>;
+	};
+
 	/* VSC8514 QSGMII quad PHY */
 	qsgmii_phy0: ethernet-phy@10 {
 		reg = <0x10>;
@@ -217,17 +221,9 @@
 
 &enetc_port0 {
 	phy-handle = <&sgmii_phy0>;
-	phy-connection-type = "sgmii";
+	phy-mode = "sgmii";
 	managed = "in-band-status";
 	status = "okay";
-
-	mdio {
-		#address-cells = <1>;
-		#size-cells = <0>;
-		sgmii_phy0: ethernet-phy@2 {
-			reg = <0x2>;
-		};
-	};
 };
 
 &enetc_port2 {
@@ -287,6 +283,11 @@
 	status = "okay";
 };
 
+&usb0 {
+	status = "okay";
+};
+
 &usb1 {
 	dr_mode = "otg";
+	status = "okay";
 };
diff --git a/arch/arm64/boot/dts/freescale/fsl-ls1028a.dtsi b/arch/arm64/boot/dts/freescale/fsl-ls1028a.dtsi
index 06b36cc65865..fd3f3e8bb6ce 100644
--- a/arch/arm64/boot/dts/freescale/fsl-ls1028a.dtsi
+++ b/arch/arm64/boot/dts/freescale/fsl-ls1028a.dtsi
@@ -80,13 +80,6 @@
 		clock-output-names = "phy_27m";
 	};
 
-	dpclk: clock-controller@f1f0000 {
-		compatible = "fsl,ls1028a-plldig";
-		reg = <0x0 0xf1f0000 0x0 0xffff>;
-		#clock-cells = <0>;
-		clocks = <&osc_27m>;
-	};
-
 	firmware {
 		optee: optee  {
 			compatible = "linaro,optee-tz";
@@ -592,6 +585,7 @@
 			snps,dis_rxdet_inp3_quirk;
 			snps,quirk-frame-length-adjustment = <0x20>;
 			snps,incr-burst-type-adjustment = <1>, <4>, <8>, <16>;
+			status = "disabled";
 		};
 
 		usb1: usb@3110000 {
@@ -602,6 +596,7 @@
 			snps,dis_rxdet_inp3_quirk;
 			snps,quirk-frame-length-adjustment = <0x20>;
 			snps,incr-burst-type-adjustment = <1>, <4>, <8>, <16>;
+			status = "disabled";
 		};
 
 		sata: sata@3200000 {
@@ -800,6 +795,38 @@
 			clock-names = "wdog_clk", "apb_pclk";
 		};
 
+		malidp0: display@f080000 {
+			compatible = "arm,mali-dp500";
+			reg = <0x0 0xf080000 0x0 0x10000>;
+			interrupts = <0 222 IRQ_TYPE_LEVEL_HIGH>,
+				     <0 223 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "DE", "SE";
+			clocks = <&dpclk>,
+				 <&clockgen QORIQ_CLK_HWACCEL 2>,
+				 <&clockgen QORIQ_CLK_HWACCEL 2>,
+				 <&clockgen QORIQ_CLK_HWACCEL 2>;
+			clock-names = "pxlclk", "mclk", "aclk", "pclk";
+			arm,malidp-output-port-lines = /bits/ 8 <8 8 8>;
+			arm,malidp-arqos-value = <0xd000d000>;
+
+			port {
+				dpi0_out: endpoint {
+
+				};
+			};
+		};
+
+		gpu: gpu@f0c0000 {
+			compatible = "vivante,gc";
+			reg = <0x0 0xf0c0000 0x0 0x10000>;
+			interrupts = <GIC_SPI 220 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&clockgen QORIQ_CLK_HWACCEL 2>,
+				 <&clockgen QORIQ_CLK_HWACCEL 2>,
+				 <&clockgen QORIQ_CLK_HWACCEL 2>;
+			clock-names = "core", "shader", "bus";
+			#cooling-cells = <2>;
+		};
+
 		sai1: audio-controller@f100000 {
 			#sound-dai-cells = <0>;
 			compatible = "fsl,vf610-sai";
@@ -926,6 +953,13 @@
 			status = "disabled";
 		};
 
+		dpclk: clock-controller@f1f0000 {
+			compatible = "fsl,ls1028a-plldig";
+			reg = <0x0 0xf1f0000 0x0 0x10000>;
+			#clock-cells = <0>;
+			clocks = <&osc_27m>;
+		};
+
 		tmu: tmu@1f80000 {
 			compatible = "fsl,qoriq-tmu";
 			reg = <0x0 0x1f80000 0x0 0x10000>;
@@ -1025,6 +1059,7 @@
 				fixed-link {
 					speed = <2500>;
 					full-duplex;
+					pause;
 				};
 			};
 
@@ -1083,6 +1118,7 @@
 						fixed-link {
 							speed = <2500>;
 							full-duplex;
+							pause;
 						};
 					};
 
@@ -1094,6 +1130,7 @@
 						fixed-link {
 							speed = <1000>;
 							full-duplex;
+							pause;
 						};
 					};
 				};
@@ -1108,6 +1145,7 @@
 				fixed-link {
 					speed = <1000>;
 					full-duplex;
+					pause;
 				};
 			};
 
@@ -1139,24 +1177,4 @@
 		};
 	};
 
-	malidp0: display@f080000 {
-		compatible = "arm,mali-dp500";
-		reg = <0x0 0xf080000 0x0 0x10000>;
-		interrupts = <0 222 IRQ_TYPE_LEVEL_HIGH>,
-			     <0 223 IRQ_TYPE_LEVEL_HIGH>;
-		interrupt-names = "DE", "SE";
-		clocks = <&dpclk>,
-			 <&clockgen QORIQ_CLK_HWACCEL 2>,
-			 <&clockgen QORIQ_CLK_HWACCEL 2>,
-			 <&clockgen QORIQ_CLK_HWACCEL 2>;
-		clock-names = "pxlclk", "mclk", "aclk", "pclk";
-		arm,malidp-output-port-lines = /bits/ 8 <8 8 8>;
-		arm,malidp-arqos-value = <0xd000d000>;
-
-		port {
-			dp0_out: endpoint {
-
-			};
-		};
-	};
 };
diff --git a/arch/arm64/boot/dts/freescale/fsl-ls1088a.dtsi b/arch/arm64/boot/dts/freescale/fsl-ls1088a.dtsi
index f85e437f80b7..f891ef6a3754 100644
--- a/arch/arm64/boot/dts/freescale/fsl-ls1088a.dtsi
+++ b/arch/arm64/boot/dts/freescale/fsl-ls1088a.dtsi
@@ -241,18 +241,18 @@
 				interrupt-controller;
 				reg = <0x14 4>;
 				interrupt-map =
-					<0 0 &gic GIC_SPI 0 IRQ_TYPE_LEVEL_HIGH>,
-					<1 0 &gic GIC_SPI 1 IRQ_TYPE_LEVEL_HIGH>,
-					<2 0 &gic GIC_SPI 2 IRQ_TYPE_LEVEL_HIGH>,
-					<3 0 &gic GIC_SPI 3 IRQ_TYPE_LEVEL_HIGH>,
-					<4 0 &gic GIC_SPI 4 IRQ_TYPE_LEVEL_HIGH>,
-					<5 0 &gic GIC_SPI 5 IRQ_TYPE_LEVEL_HIGH>,
-					<6 0 &gic GIC_SPI 6 IRQ_TYPE_LEVEL_HIGH>,
-					<7 0 &gic GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>,
-					<8 0 &gic GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>,
-					<9 0 &gic GIC_SPI 9 IRQ_TYPE_LEVEL_HIGH>,
-					<10 0 &gic GIC_SPI 10 IRQ_TYPE_LEVEL_HIGH>,
-					<11 0 &gic GIC_SPI 11 IRQ_TYPE_LEVEL_HIGH>;
+					<0 0 &gic 0 0 GIC_SPI 0 IRQ_TYPE_LEVEL_HIGH>,
+					<1 0 &gic 0 0 GIC_SPI 1 IRQ_TYPE_LEVEL_HIGH>,
+					<2 0 &gic 0 0 GIC_SPI 2 IRQ_TYPE_LEVEL_HIGH>,
+					<3 0 &gic 0 0 GIC_SPI 3 IRQ_TYPE_LEVEL_HIGH>,
+					<4 0 &gic 0 0 GIC_SPI 4 IRQ_TYPE_LEVEL_HIGH>,
+					<5 0 &gic 0 0 GIC_SPI 5 IRQ_TYPE_LEVEL_HIGH>,
+					<6 0 &gic 0 0 GIC_SPI 6 IRQ_TYPE_LEVEL_HIGH>,
+					<7 0 &gic 0 0 GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>,
+					<8 0 &gic 0 0 GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>,
+					<9 0 &gic 0 0 GIC_SPI 9 IRQ_TYPE_LEVEL_HIGH>,
+					<10 0 &gic 0 0 GIC_SPI 10 IRQ_TYPE_LEVEL_HIGH>,
+					<11 0 &gic 0 0 GIC_SPI 11 IRQ_TYPE_LEVEL_HIGH>;
 				interrupt-map-mask = <0xffffffff 0x0>;
 			};
 		};
@@ -847,7 +847,7 @@
 		};
 
 		cluster1_core0_watchdog: wdt@c000000 {
-			compatible = "arm,sp805-wdt", "arm,primecell";
+			compatible = "arm,sp805", "arm,primecell";
 			reg = <0x0 0xc000000 0x0 0x1000>;
 			clocks = <&clockgen QORIQ_CLK_PLATFORM_PLL
 					    QORIQ_CLK_PLL_DIV(16)>,
@@ -857,7 +857,7 @@
 		};
 
 		cluster1_core1_watchdog: wdt@c010000 {
-			compatible = "arm,sp805-wdt", "arm,primecell";
+			compatible = "arm,sp805", "arm,primecell";
 			reg = <0x0 0xc010000 0x0 0x1000>;
 			clocks = <&clockgen QORIQ_CLK_PLATFORM_PLL
 					    QORIQ_CLK_PLL_DIV(16)>,
@@ -867,7 +867,7 @@
 		};
 
 		cluster1_core2_watchdog: wdt@c020000 {
-			compatible = "arm,sp805-wdt", "arm,primecell";
+			compatible = "arm,sp805", "arm,primecell";
 			reg = <0x0 0xc020000 0x0 0x1000>;
 			clocks = <&clockgen QORIQ_CLK_PLATFORM_PLL
 					    QORIQ_CLK_PLL_DIV(16)>,
@@ -877,7 +877,7 @@
 		};
 
 		cluster1_core3_watchdog: wdt@c030000 {
-			compatible = "arm,sp805-wdt", "arm,primecell";
+			compatible = "arm,sp805", "arm,primecell";
 			reg = <0x0 0xc030000 0x0 0x1000>;
 			clocks = <&clockgen QORIQ_CLK_PLATFORM_PLL
 					    QORIQ_CLK_PLL_DIV(16)>,
@@ -887,7 +887,7 @@
 		};
 
 		cluster2_core0_watchdog: wdt@c100000 {
-			compatible = "arm,sp805-wdt", "arm,primecell";
+			compatible = "arm,sp805", "arm,primecell";
 			reg = <0x0 0xc100000 0x0 0x1000>;
 			clocks = <&clockgen QORIQ_CLK_PLATFORM_PLL
 					    QORIQ_CLK_PLL_DIV(16)>,
@@ -897,7 +897,7 @@
 		};
 
 		cluster2_core1_watchdog: wdt@c110000 {
-			compatible = "arm,sp805-wdt", "arm,primecell";
+			compatible = "arm,sp805", "arm,primecell";
 			reg = <0x0 0xc110000 0x0 0x1000>;
 			clocks = <&clockgen QORIQ_CLK_PLATFORM_PLL
 					    QORIQ_CLK_PLL_DIV(16)>,
@@ -907,7 +907,7 @@
 		};
 
 		cluster2_core2_watchdog: wdt@c120000 {
-			compatible = "arm,sp805-wdt", "arm,primecell";
+			compatible = "arm,sp805", "arm,primecell";
 			reg = <0x0 0xc120000 0x0 0x1000>;
 			clocks = <&clockgen QORIQ_CLK_PLATFORM_PLL
 					    QORIQ_CLK_PLL_DIV(16)>,
@@ -917,7 +917,7 @@
 		};
 
 		cluster2_core3_watchdog: wdt@c130000 {
-			compatible = "arm,sp805-wdt", "arm,primecell";
+			compatible = "arm,sp805", "arm,primecell";
 			reg = <0x0 0xc130000 0x0 0x1000>;
 			clocks = <&clockgen QORIQ_CLK_PLATFORM_PLL
 					    QORIQ_CLK_PLL_DIV(16)>,
diff --git a/arch/arm64/boot/dts/freescale/fsl-ls208xa.dtsi b/arch/arm64/boot/dts/freescale/fsl-ls208xa.dtsi
index 801ba9612d36..3cb9c21d2775 100644
--- a/arch/arm64/boot/dts/freescale/fsl-ls208xa.dtsi
+++ b/arch/arm64/boot/dts/freescale/fsl-ls208xa.dtsi
@@ -293,18 +293,18 @@
 				interrupt-controller;
 				reg = <0x14 4>;
 				interrupt-map =
-					<0 0 &gic GIC_SPI 0 IRQ_TYPE_LEVEL_HIGH>,
-					<1 0 &gic GIC_SPI 1 IRQ_TYPE_LEVEL_HIGH>,
-					<2 0 &gic GIC_SPI 2 IRQ_TYPE_LEVEL_HIGH>,
-					<3 0 &gic GIC_SPI 3 IRQ_TYPE_LEVEL_HIGH>,
-					<4 0 &gic GIC_SPI 4 IRQ_TYPE_LEVEL_HIGH>,
-					<5 0 &gic GIC_SPI 5 IRQ_TYPE_LEVEL_HIGH>,
-					<6 0 &gic GIC_SPI 6 IRQ_TYPE_LEVEL_HIGH>,
-					<7 0 &gic GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>,
-					<8 0 &gic GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>,
-					<9 0 &gic GIC_SPI 9 IRQ_TYPE_LEVEL_HIGH>,
-					<10 0 &gic GIC_SPI 10 IRQ_TYPE_LEVEL_HIGH>,
-					<11 0 &gic GIC_SPI 11 IRQ_TYPE_LEVEL_HIGH>;
+					<0 0 &gic 0 0 GIC_SPI 0 IRQ_TYPE_LEVEL_HIGH>,
+					<1 0 &gic 0 0 GIC_SPI 1 IRQ_TYPE_LEVEL_HIGH>,
+					<2 0 &gic 0 0 GIC_SPI 2 IRQ_TYPE_LEVEL_HIGH>,
+					<3 0 &gic 0 0 GIC_SPI 3 IRQ_TYPE_LEVEL_HIGH>,
+					<4 0 &gic 0 0 GIC_SPI 4 IRQ_TYPE_LEVEL_HIGH>,
+					<5 0 &gic 0 0 GIC_SPI 5 IRQ_TYPE_LEVEL_HIGH>,
+					<6 0 &gic 0 0 GIC_SPI 6 IRQ_TYPE_LEVEL_HIGH>,
+					<7 0 &gic 0 0 GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>,
+					<8 0 &gic 0 0 GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>,
+					<9 0 &gic 0 0 GIC_SPI 9 IRQ_TYPE_LEVEL_HIGH>,
+					<10 0 &gic 0 0 GIC_SPI 10 IRQ_TYPE_LEVEL_HIGH>,
+					<11 0 &gic 0 0 GIC_SPI 11 IRQ_TYPE_LEVEL_HIGH>;
 				interrupt-map-mask = <0xffffffff 0x0>;
 			};
 		};
@@ -387,7 +387,7 @@
 		};
 
 		cluster1_core0_watchdog: wdt@c000000 {
-			compatible = "arm,sp805-wdt", "arm,primecell";
+			compatible = "arm,sp805", "arm,primecell";
 			reg = <0x0 0xc000000 0x0 0x1000>;
 			clocks = <&clockgen QORIQ_CLK_PLATFORM_PLL
 					    QORIQ_CLK_PLL_DIV(4)>,
@@ -397,7 +397,7 @@
 		};
 
 		cluster1_core1_watchdog: wdt@c010000 {
-			compatible = "arm,sp805-wdt", "arm,primecell";
+			compatible = "arm,sp805", "arm,primecell";
 			reg = <0x0 0xc010000 0x0 0x1000>;
 			clocks = <&clockgen QORIQ_CLK_PLATFORM_PLL
 					    QORIQ_CLK_PLL_DIV(4)>,
@@ -407,7 +407,7 @@
 		};
 
 		cluster2_core0_watchdog: wdt@c100000 {
-			compatible = "arm,sp805-wdt", "arm,primecell";
+			compatible = "arm,sp805", "arm,primecell";
 			reg = <0x0 0xc100000 0x0 0x1000>;
 			clocks = <&clockgen QORIQ_CLK_PLATFORM_PLL
 					    QORIQ_CLK_PLL_DIV(4)>,
@@ -417,7 +417,7 @@
 		};
 
 		cluster2_core1_watchdog: wdt@c110000 {
-			compatible = "arm,sp805-wdt", "arm,primecell";
+			compatible = "arm,sp805", "arm,primecell";
 			reg = <0x0 0xc110000 0x0 0x1000>;
 			clocks = <&clockgen QORIQ_CLK_PLATFORM_PLL
 					    QORIQ_CLK_PLL_DIV(4)>,
@@ -427,7 +427,7 @@
 		};
 
 		cluster3_core0_watchdog: wdt@c200000 {
-			compatible = "arm,sp805-wdt", "arm,primecell";
+			compatible = "arm,sp805", "arm,primecell";
 			reg = <0x0 0xc200000 0x0 0x1000>;
 			clocks = <&clockgen QORIQ_CLK_PLATFORM_PLL
 					    QORIQ_CLK_PLL_DIV(4)>,
@@ -437,7 +437,7 @@
 		};
 
 		cluster3_core1_watchdog: wdt@c210000 {
-			compatible = "arm,sp805-wdt", "arm,primecell";
+			compatible = "arm,sp805", "arm,primecell";
 			reg = <0x0 0xc210000 0x0 0x1000>;
 			clocks = <&clockgen QORIQ_CLK_PLATFORM_PLL
 					    QORIQ_CLK_PLL_DIV(4)>,
@@ -447,7 +447,7 @@
 		};
 
 		cluster4_core0_watchdog: wdt@c300000 {
-			compatible = "arm,sp805-wdt", "arm,primecell";
+			compatible = "arm,sp805", "arm,primecell";
 			reg = <0x0 0xc300000 0x0 0x1000>;
 			clocks = <&clockgen QORIQ_CLK_PLATFORM_PLL
 					    QORIQ_CLK_PLL_DIV(4)>,
@@ -457,7 +457,7 @@
 		};
 
 		cluster4_core1_watchdog: wdt@c310000 {
-			compatible = "arm,sp805-wdt", "arm,primecell";
+			compatible = "arm,sp805", "arm,primecell";
 			reg = <0x0 0xc310000 0x0 0x1000>;
 			clocks = <&clockgen QORIQ_CLK_PLATFORM_PLL
 					    QORIQ_CLK_PLL_DIV(4)>,
diff --git a/arch/arm64/boot/dts/freescale/fsl-lx2160a-bluebox3-rev-a.dts b/arch/arm64/boot/dts/freescale/fsl-lx2160a-bluebox3-rev-a.dts
new file mode 100644
index 000000000000..15d273c93154
--- /dev/null
+++ b/arch/arm64/boot/dts/freescale/fsl-lx2160a-bluebox3-rev-a.dts
@@ -0,0 +1,34 @@
+// SPDX-License-Identifier: (GPL-2.0 OR MIT)
+//
+// Device Tree file for LX2160A BLUEBOX3
+//
+// Copyright 2020-2021 NXP
+
+/dts-v1/;
+
+#include "fsl-lx2160a-bluebox3.dts"
+
+/ {
+	compatible = "fsl,lx2160a-bluebox3-rev-a", "fsl,lx2160a";
+};
+
+/* The RGMII PHYs have a different MDIO address */
+&emdio1 {
+	/delete-node/ ethernet-phy@5;
+
+	sw1_mii3_phy: ethernet-phy@1 {
+		/* AR8035 */
+		compatible = "ethernet-phy-id004d.d072";
+		reg = <0x1>;
+		interrupts-extended = <&extirq 6 IRQ_TYPE_LEVEL_LOW>;
+	};
+
+	/delete-node/ ethernet-phy@6;
+
+	sw2_mii3_phy: ethernet-phy@2 {
+		/* AR8035 */
+		compatible = "ethernet-phy-id004d.d072";
+		reg = <0x2>;
+		interrupts-extended = <&extirq 7 IRQ_TYPE_LEVEL_LOW>;
+	};
+};
diff --git a/arch/arm64/boot/dts/freescale/fsl-lx2160a-bluebox3.dts b/arch/arm64/boot/dts/freescale/fsl-lx2160a-bluebox3.dts
new file mode 100644
index 000000000000..b21be03da0af
--- /dev/null
+++ b/arch/arm64/boot/dts/freescale/fsl-lx2160a-bluebox3.dts
@@ -0,0 +1,658 @@
+// SPDX-License-Identifier: (GPL-2.0 OR MIT)
+//
+// Device Tree file for LX2160A BLUEBOX3
+//
+// Copyright 2020-2021 NXP
+
+/dts-v1/;
+
+#include "fsl-lx2160a.dtsi"
+
+/ {
+	model = "NXP Layerscape LX2160ABLUEBOX3";
+	compatible = "fsl,lx2160a-bluebox3", "fsl,lx2160a";
+
+	aliases {
+		crypto = &crypto;
+		mmc0 = &esdhc0;
+		mmc1 = &esdhc1;
+		serial0 = &uart0;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	sb_3v3: regulator-sb3v3 {
+		compatible = "regulator-fixed";
+		regulator-name = "MC34717-3.3VSB";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-boot-on;
+		regulator-always-on;
+	};
+};
+
+&can0 {
+	status = "okay";
+
+	can-transceiver {
+		max-bitrate = <5000000>;
+	};
+};
+
+&can1 {
+	status = "okay";
+
+	can-transceiver {
+		max-bitrate = <5000000>;
+	};
+};
+
+&crypto {
+	status = "okay";
+};
+
+&dpmac5 {
+	phy-handle = <&aqr113c_phy1>;
+	phy-mode = "usxgmii";
+	managed = "in-band-status";
+};
+
+&dpmac6 {
+	phy-handle = <&aqr113c_phy2>;
+	phy-mode = "usxgmii";
+	managed = "in-band-status";
+};
+
+&dpmac9 {
+	phy-handle = <&aqr113c_phy3>;
+	phy-mode = "usxgmii";
+	managed = "in-band-status";
+};
+
+&dpmac10 {
+	phy-handle = <&aqr113c_phy4>;
+	phy-mode = "usxgmii";
+	managed = "in-band-status";
+};
+
+&dpmac17 {
+	phy-mode = "rgmii";
+	status = "okay";
+
+	fixed-link {
+		speed = <1000>;
+		full-duplex;
+	};
+};
+
+&dpmac18 {
+	phy-mode = "rgmii";
+	status = "okay";
+
+	fixed-link {
+		speed = <1000>;
+		full-duplex;
+	};
+};
+
+&emdio1 {
+	status = "okay";
+
+	aqr113c_phy2: ethernet-phy@0 {
+		compatible = "ethernet-phy-ieee802.3-c45";
+		reg = <0x0>;
+		/* IRQ_10G_PHY2 */
+		interrupts-extended = <&extirq 3 IRQ_TYPE_LEVEL_LOW>;
+	};
+
+	aqr113c_phy1: ethernet-phy@8 {
+		compatible = "ethernet-phy-ieee802.3-c45";
+		reg = <0x8>;
+		/* IRQ_10G_PHY1 */
+		interrupts-extended = <&extirq 2 IRQ_TYPE_LEVEL_LOW>;
+	};
+
+	sw1_mii3_phy: ethernet-phy@5 {
+		/* AR8035 */
+		compatible = "ethernet-phy-id004d.d072";
+		reg = <0x5>;
+		interrupts-extended = <&extirq 6 IRQ_TYPE_LEVEL_LOW>;
+	};
+
+	sw2_mii3_phy: ethernet-phy@6 {
+		/* AR8035 */
+		compatible = "ethernet-phy-id004d.d072";
+		reg = <0x6>;
+		interrupts-extended = <&extirq 7 IRQ_TYPE_LEVEL_LOW>;
+	};
+};
+
+&emdio2 {
+	status = "okay";
+
+	aqr113c_phy4: ethernet-phy@0 {
+		compatible = "ethernet-phy-ieee802.3-c45";
+		reg = <0x0>;
+		/* IRQ_10G_PHY4 */
+		interrupts-extended = <&extirq 5 IRQ_TYPE_LEVEL_LOW>;
+	};
+
+	aqr113c_phy3: ethernet-phy@8 {
+		compatible = "ethernet-phy-ieee802.3-c45";
+		reg = <0x8>;
+		/* IRQ_10G_PHY3 */
+		interrupts-extended = <&extirq 4 IRQ_TYPE_LEVEL_LOW>;
+	};
+};
+
+&esdhc0 {
+	sd-uhs-sdr104;
+	sd-uhs-sdr50;
+	sd-uhs-sdr25;
+	sd-uhs-sdr12;
+	status = "okay";
+};
+
+&esdhc1 {
+	mmc-hs200-1_8v;
+	mmc-hs400-1_8v;
+	bus-width = <8>;
+	status = "okay";
+};
+
+&fspi {
+	status = "okay";
+
+	mt35xu512aba0: flash@0 {
+		compatible = "jedec,spi-nor";
+		#address-cells = <1>;
+		#size-cells = <1>;
+		reg = <0>;
+		m25p,fast-read;
+		spi-max-frequency = <50000000>;
+		spi-rx-bus-width = <8>;
+		spi-tx-bus-width = <8>;
+	};
+
+	mt35xu512aba1: flash@1 {
+		compatible = "jedec,spi-nor";
+		#address-cells = <1>;
+		#size-cells = <1>;
+		reg = <1>;
+		m25p,fast-read;
+		spi-max-frequency = <50000000>;
+		spi-rx-bus-width = <8>;
+		spi-tx-bus-width = <8>;
+	};
+};
+
+&i2c0 {
+	status = "okay";
+
+	i2c-mux@77 {
+		compatible = "nxp,pca9547";
+		reg = <0x77>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		i2c@2 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0x2>;
+
+			power-monitor@40 {
+				compatible = "ti,ina220";
+				reg = <0x40>;
+				shunt-resistor = <500>;
+			};
+		};
+
+		i2c@3 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0x3>;
+
+			temp2: temperature-sensor@48 {
+				compatible = "nxp,sa56004";
+				reg = <0x48>;
+				vcc-supply = <&sb_3v3>;
+				#thermal-sensor-cells = <1>;
+			};
+
+			temp1: temperature-sensor@4c {
+				compatible = "nxp,sa56004";
+				reg = <0x4c>;
+				vcc-supply = <&sb_3v3>;
+				#thermal-sensor-cells = <1>;
+			};
+		};
+
+		i2c@4 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0x4>;
+
+			rtc@51 {
+				compatible = "nxp,pcf2129";
+				reg = <0x51>;
+				interrupts-extended = <&extirq 11 IRQ_TYPE_LEVEL_LOW>;
+			};
+		};
+
+		i2c@7 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0x7>;
+
+			i2c-mux@75 {
+				compatible = "nxp,pca9547";
+				reg = <0x75>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				i2c@0 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <0x0>;
+
+					spi_bridge: spi@28 {
+						compatible = "nxp,sc18is602b";
+						reg = <0x28>;
+						#address-cells = <1>;
+						#size-cells = <0>;
+					};
+				};
+			};
+		};
+	};
+};
+
+&i2c5 {
+	status = "okay";
+
+	i2c-mux@77 {
+		compatible = "nxp,pca9846";
+		reg = <0x77>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		i2c@1 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0x1>;
+
+			/* The I2C multiplexer and temperature sensors are on
+			 * the T6 riser card.
+			 */
+			i2c-mux@70 {
+				compatible = "nxp,pca9548";
+				reg = <0x70>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				i2c@6 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <0x6>;
+
+					q12: temperature-sensor@4c {
+						compatible = "nxp,sa56004";
+						reg = <0x4c>;
+						vcc-supply = <&sb_3v3>;
+						#thermal-sensor-cells = <1>;
+					};
+				};
+
+				i2c@7 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <0x7>;
+
+					q11: temperature-sensor@4c {
+						compatible = "nxp,sa56004";
+						reg = <0x4c>;
+						vcc-supply = <&sb_3v3>;
+						#thermal-sensor-cells = <1>;
+					};
+
+					q13: temperature-sensor@48 {
+						compatible = "nxp,sa56004";
+						reg = <0x48>;
+						vcc-supply = <&sb_3v3>;
+						#thermal-sensor-cells = <1>;
+					};
+
+					q14: temperature-sensor@4a {
+						compatible = "nxp,sa56004";
+						reg = <0x4a>;
+						vcc-supply = <&sb_3v3>;
+						#thermal-sensor-cells = <1>;
+					};
+				};
+			};
+		};
+	};
+};
+
+&pcs_mdio5 {
+	status = "okay";
+};
+
+&pcs_mdio6 {
+	status = "okay";
+};
+
+&pcs_mdio9 {
+	status = "okay";
+};
+
+&pcs_mdio10 {
+	status = "okay";
+};
+
+&spi_bridge {
+	sw1: ethernet-switch@0 {
+		compatible = "nxp,sja1110a";
+		reg = <0>;
+		spi-max-frequency = <4000000>;
+		spi-cpol;
+		dsa,member = <0 0>;
+
+		ethernet-ports {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			/* Microcontroller port */
+			port@0 {
+				reg = <0>;
+				status = "disabled";
+			};
+
+			/* SW1_P1 */
+			port@1 {
+				reg = <1>;
+				label = "con_2x20";
+				phy-mode = "sgmii";
+
+				fixed-link {
+					speed = <1000>;
+					full-duplex;
+				};
+			};
+
+			port@2 {
+				reg = <2>;
+				ethernet = <&dpmac17>;
+				phy-mode = "rgmii-id";
+
+				fixed-link {
+					speed = <1000>;
+					full-duplex;
+				};
+			};
+
+			port@3 {
+				reg = <3>;
+				label = "1ge_p1";
+				phy-mode = "rgmii-id";
+				phy-handle = <&sw1_mii3_phy>;
+			};
+
+			sw1p4: port@4 {
+				reg = <4>;
+				link = <&sw2p1>;
+				phy-mode = "sgmii";
+
+				fixed-link {
+					speed = <1000>;
+					full-duplex;
+				};
+			};
+
+			port@5 {
+				reg = <5>;
+				label = "trx1";
+				phy-mode = "internal";
+				phy-handle = <&sw1_port5_base_t1_phy>;
+			};
+
+			port@6 {
+				reg = <6>;
+				label = "trx2";
+				phy-mode = "internal";
+				phy-handle = <&sw1_port6_base_t1_phy>;
+			};
+
+			port@7 {
+				reg = <7>;
+				label = "trx3";
+				phy-mode = "internal";
+				phy-handle = <&sw1_port7_base_t1_phy>;
+			};
+
+			port@8 {
+				reg = <8>;
+				label = "trx4";
+				phy-mode = "internal";
+				phy-handle = <&sw1_port8_base_t1_phy>;
+			};
+
+			port@9 {
+				reg = <9>;
+				label = "trx5";
+				phy-mode = "internal";
+				phy-handle = <&sw1_port9_base_t1_phy>;
+			};
+
+			port@a {
+				reg = <10>;
+				label = "trx6";
+				phy-mode = "internal";
+				phy-handle = <&sw1_port10_base_t1_phy>;
+			};
+		};
+
+		mdios {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			mdio@0 {
+				compatible = "nxp,sja1110-base-t1-mdio";
+				#address-cells = <1>;
+				#size-cells = <0>;
+				reg = <0>;
+
+				sw1_port5_base_t1_phy: ethernet-phy@1 {
+					compatible = "ethernet-phy-ieee802.3-c45";
+					reg = <0x1>;
+				};
+
+				sw1_port6_base_t1_phy: ethernet-phy@2 {
+					compatible = "ethernet-phy-ieee802.3-c45";
+					reg = <0x2>;
+				};
+
+				sw1_port7_base_t1_phy: ethernet-phy@3 {
+					compatible = "ethernet-phy-ieee802.3-c45";
+					reg = <0x3>;
+				};
+
+				sw1_port8_base_t1_phy: ethernet-phy@4 {
+					compatible = "ethernet-phy-ieee802.3-c45";
+					reg = <0x4>;
+				};
+
+				sw1_port9_base_t1_phy: ethernet-phy@5 {
+					compatible = "ethernet-phy-ieee802.3-c45";
+					reg = <0x5>;
+				};
+
+				sw1_port10_base_t1_phy: ethernet-phy@6 {
+					compatible = "ethernet-phy-ieee802.3-c45";
+					reg = <0x6>;
+				};
+			};
+		};
+	};
+
+	sw2: ethernet-switch@2 {
+		compatible = "nxp,sja1110a";
+		reg = <2>;
+		spi-max-frequency = <4000000>;
+		spi-cpol;
+		dsa,member = <0 1>;
+
+		ethernet-ports {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			/* Microcontroller port */
+			port@0 {
+				reg = <0>;
+				status = "disabled";
+			};
+
+			sw2p1: port@1 {
+				reg = <1>;
+				link = <&sw1p4>;
+				phy-mode = "sgmii";
+
+				fixed-link {
+					speed = <1000>;
+					full-duplex;
+				};
+			};
+
+			port@2 {
+				reg = <2>;
+				ethernet = <&dpmac18>;
+				phy-mode = "rgmii-id";
+
+				fixed-link {
+					speed = <1000>;
+					full-duplex;
+				};
+			};
+
+			port@3 {
+				reg = <3>;
+				label = "1ge_p2";
+				phy-mode = "rgmii-id";
+				phy-handle = <&sw2_mii3_phy>;
+			};
+
+			port@4 {
+				reg = <4>;
+				label = "to_sw3";
+				phy-mode = "2500base-x";
+
+				fixed-link {
+					speed = <2500>;
+					full-duplex;
+				};
+			};
+
+			port@5 {
+				reg = <5>;
+				label = "trx7";
+				phy-mode = "internal";
+				phy-handle = <&sw2_port5_base_t1_phy>;
+			};
+
+			port@6 {
+				reg = <6>;
+				label = "trx8";
+				phy-mode = "internal";
+				phy-handle = <&sw2_port6_base_t1_phy>;
+			};
+
+			port@7 {
+				reg = <7>;
+				label = "trx9";
+				phy-mode = "internal";
+				phy-handle = <&sw2_port7_base_t1_phy>;
+			};
+
+			port@8 {
+				reg = <8>;
+				label = "trx10";
+				phy-mode = "internal";
+				phy-handle = <&sw2_port8_base_t1_phy>;
+			};
+
+			port@9 {
+				reg = <9>;
+				label = "trx11";
+				phy-mode = "internal";
+				phy-handle = <&sw2_port9_base_t1_phy>;
+			};
+
+			port@a {
+				reg = <10>;
+				label = "trx12";
+				phy-mode = "internal";
+				phy-handle = <&sw2_port10_base_t1_phy>;
+			};
+		};
+
+		mdios {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			mdio@0 {
+				compatible = "nxp,sja1110-base-t1-mdio";
+				#address-cells = <1>;
+				#size-cells = <0>;
+				reg = <0>;
+
+				sw2_port5_base_t1_phy: ethernet-phy@1 {
+					compatible = "ethernet-phy-ieee802.3-c45";
+					reg = <0x1>;
+				};
+
+				sw2_port6_base_t1_phy: ethernet-phy@2 {
+					compatible = "ethernet-phy-ieee802.3-c45";
+					reg = <0x2>;
+				};
+
+				sw2_port7_base_t1_phy: ethernet-phy@3 {
+					compatible = "ethernet-phy-ieee802.3-c45";
+					reg = <0x3>;
+				};
+
+				sw2_port8_base_t1_phy: ethernet-phy@4 {
+					compatible = "ethernet-phy-ieee802.3-c45";
+					reg = <0x4>;
+				};
+
+				sw2_port9_base_t1_phy: ethernet-phy@5 {
+					compatible = "ethernet-phy-ieee802.3-c45";
+					reg = <0x5>;
+				};
+
+				sw2_port10_base_t1_phy: ethernet-phy@6 {
+					compatible = "ethernet-phy-ieee802.3-c45";
+					reg = <0x6>;
+				};
+			};
+		};
+	};
+};
+
+&uart0 {
+	status = "okay";
+};
+
+&uart1 {
+	status = "okay";
+};
+
+&usb0 {
+	status = "okay";
+};
+
+&usb1 {
+	status = "okay";
+};
diff --git a/arch/arm64/boot/dts/freescale/fsl-lx2160a.dtsi b/arch/arm64/boot/dts/freescale/fsl-lx2160a.dtsi
index c4b1a59ba424..dc8661ebd1f6 100644
--- a/arch/arm64/boot/dts/freescale/fsl-lx2160a.dtsi
+++ b/arch/arm64/boot/dts/freescale/fsl-lx2160a.dtsi
@@ -680,18 +680,18 @@
 				interrupt-controller;
 				reg = <0x14 4>;
 				interrupt-map =
-					<0 0 &gic GIC_SPI 0 IRQ_TYPE_LEVEL_HIGH>,
-					<1 0 &gic GIC_SPI 1 IRQ_TYPE_LEVEL_HIGH>,
-					<2 0 &gic GIC_SPI 2 IRQ_TYPE_LEVEL_HIGH>,
-					<3 0 &gic GIC_SPI 3 IRQ_TYPE_LEVEL_HIGH>,
-					<4 0 &gic GIC_SPI 4 IRQ_TYPE_LEVEL_HIGH>,
-					<5 0 &gic GIC_SPI 5 IRQ_TYPE_LEVEL_HIGH>,
-					<6 0 &gic GIC_SPI 6 IRQ_TYPE_LEVEL_HIGH>,
-					<7 0 &gic GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>,
-					<8 0 &gic GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>,
-					<9 0 &gic GIC_SPI 9 IRQ_TYPE_LEVEL_HIGH>,
-					<10 0 &gic GIC_SPI 10 IRQ_TYPE_LEVEL_HIGH>,
-					<11 0 &gic GIC_SPI 11 IRQ_TYPE_LEVEL_HIGH>;
+					<0 0 &gic 0 0 GIC_SPI 0 IRQ_TYPE_LEVEL_HIGH>,
+					<1 0 &gic 0 0 GIC_SPI 1 IRQ_TYPE_LEVEL_HIGH>,
+					<2 0 &gic 0 0 GIC_SPI 2 IRQ_TYPE_LEVEL_HIGH>,
+					<3 0 &gic 0 0 GIC_SPI 3 IRQ_TYPE_LEVEL_HIGH>,
+					<4 0 &gic 0 0 GIC_SPI 4 IRQ_TYPE_LEVEL_HIGH>,
+					<5 0 &gic 0 0 GIC_SPI 5 IRQ_TYPE_LEVEL_HIGH>,
+					<6 0 &gic 0 0 GIC_SPI 6 IRQ_TYPE_LEVEL_HIGH>,
+					<7 0 &gic 0 0 GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>,
+					<8 0 &gic 0 0 GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>,
+					<9 0 &gic 0 0 GIC_SPI 9 IRQ_TYPE_LEVEL_HIGH>,
+					<10 0 &gic 0 0 GIC_SPI 10 IRQ_TYPE_LEVEL_HIGH>,
+					<11 0 &gic 0 0 GIC_SPI 11 IRQ_TYPE_LEVEL_HIGH>;
 				interrupt-map-mask = <0xffffffff 0x0>;
 			};
 		};
diff --git a/arch/arm64/boot/dts/freescale/imx8mm-kontron-n801x-s.dts b/arch/arm64/boot/dts/freescale/imx8mm-kontron-n801x-s.dts
index e99e7644ff39..d40caf14ac4a 100644
--- a/arch/arm64/boot/dts/freescale/imx8mm-kontron-n801x-s.dts
+++ b/arch/arm64/boot/dts/freescale/imx8mm-kontron-n801x-s.dts
@@ -123,8 +123,8 @@
 
 		ethphy: ethernet-phy@0 {
 			reg = <0>;
-			reset-assert-us = <100>;
-			reset-deassert-us = <100>;
+			reset-assert-us = <1>;
+			reset-deassert-us = <15000>;
 			reset-gpios = <&gpio4 27 GPIO_ACTIVE_LOW>;
 		};
 	};
@@ -191,8 +191,10 @@
 };
 
 &usdhc2 {
-	pinctrl-names = "default";
+	pinctrl-names = "default", "state_100mhz", "state_200mhz";
 	pinctrl-0 = <&pinctrl_usdhc2>;
+	pinctrl-1 = <&pinctrl_usdhc2_100mhz>;
+	pinctrl-2 = <&pinctrl_usdhc2_200mhz>;
 	vmmc-supply = <&reg_vdd_3v3>;
 	vqmmc-supply = <&reg_nvcc_sd>;
 	cd-gpios = <&gpio2 12 GPIO_ACTIVE_LOW>;
@@ -321,4 +323,28 @@
 			MX8MM_IOMUXC_SD2_CD_B_GPIO2_IO12		0x019
 		>;
 	};
+
+	pinctrl_usdhc2_100mhz: usdhc2-100mhzgrp {
+		fsl,pins = <
+			MX8MM_IOMUXC_SD2_CLK_USDHC2_CLK			0x194
+			MX8MM_IOMUXC_SD2_CMD_USDHC2_CMD			0x1d4
+			MX8MM_IOMUXC_SD2_DATA0_USDHC2_DATA0		0x1d4
+			MX8MM_IOMUXC_SD2_DATA1_USDHC2_DATA1		0x1d4
+			MX8MM_IOMUXC_SD2_DATA2_USDHC2_DATA2		0x1d4
+			MX8MM_IOMUXC_SD2_DATA3_USDHC2_DATA3		0x1d4
+			MX8MM_IOMUXC_SD2_CD_B_GPIO2_IO12		0x019
+		>;
+	};
+
+	pinctrl_usdhc2_200mhz: usdhc2-200mhzgrp {
+		fsl,pins = <
+			MX8MM_IOMUXC_SD2_CLK_USDHC2_CLK			0x196
+			MX8MM_IOMUXC_SD2_CMD_USDHC2_CMD			0x1d6
+			MX8MM_IOMUXC_SD2_DATA0_USDHC2_DATA0		0x1d6
+			MX8MM_IOMUXC_SD2_DATA1_USDHC2_DATA1		0x1d6
+			MX8MM_IOMUXC_SD2_DATA2_USDHC2_DATA2		0x1d6
+			MX8MM_IOMUXC_SD2_DATA3_USDHC2_DATA3		0x1d6
+			MX8MM_IOMUXC_SD2_CD_B_GPIO2_IO12		0x019
+		>;
+	};
 };
diff --git a/arch/arm64/boot/dts/freescale/imx8mm-kontron-n801x-som.dtsi b/arch/arm64/boot/dts/freescale/imx8mm-kontron-n801x-som.dtsi
index 42bbbb3f532b..22a5ef771d4e 100644
--- a/arch/arm64/boot/dts/freescale/imx8mm-kontron-n801x-som.dtsi
+++ b/arch/arm64/boot/dts/freescale/imx8mm-kontron-n801x-som.dtsi
@@ -63,7 +63,7 @@
 &ecspi1 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_ecspi1>;
-	cs-gpios = <&gpio5 9 GPIO_ACTIVE_HIGH>;
+	cs-gpios = <&gpio5 9 GPIO_ACTIVE_LOW>;
 	status = "okay";
 
 	spi-flash@0 {
@@ -86,6 +86,7 @@
 		pinctrl-0 = <&pinctrl_pmic>;
 		interrupt-parent = <&gpio1>;
 		interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
+		sd-vsel-gpios = <&gpio1 4 GPIO_ACTIVE_HIGH>;
 
 		regulators {
 			reg_vdd_soc: BUCK1 {
@@ -228,6 +229,7 @@
 	pinctrl_pmic: pmicgrp {
 		fsl,pins = <
 			MX8MM_IOMUXC_GPIO1_IO00_GPIO1_IO0		0x141
+			MX8MM_IOMUXC_GPIO1_IO04_GPIO1_IO4		0x141
 		>;
 	};
 
diff --git a/arch/arm64/boot/dts/freescale/imx8mm-venice-gw71xx.dtsi b/arch/arm64/boot/dts/freescale/imx8mm-venice-gw71xx.dtsi
index 8e4a0ce99790..28012279f6f6 100644
--- a/arch/arm64/boot/dts/freescale/imx8mm-venice-gw71xx.dtsi
+++ b/arch/arm64/boot/dts/freescale/imx8mm-venice-gw71xx.dtsi
@@ -57,7 +57,7 @@
 &ecspi2 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_spi2>;
-	cs-gpios = <&gpio5 13 GPIO_ACTIVE_HIGH>;
+	cs-gpios = <&gpio5 13 GPIO_ACTIVE_LOW>;
 	status = "okay";
 };
 
diff --git a/arch/arm64/boot/dts/freescale/imx8mm-venice-gw72xx.dtsi b/arch/arm64/boot/dts/freescale/imx8mm-venice-gw72xx.dtsi
index b7c91bdc21dd..27afa46a253a 100644
--- a/arch/arm64/boot/dts/freescale/imx8mm-venice-gw72xx.dtsi
+++ b/arch/arm64/boot/dts/freescale/imx8mm-venice-gw72xx.dtsi
@@ -76,7 +76,7 @@
 &ecspi2 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_spi2>;
-	cs-gpios = <&gpio5 13 GPIO_ACTIVE_HIGH>;
+	cs-gpios = <&gpio5 13 GPIO_ACTIVE_LOW>;
 	status = "okay";
 };
 
diff --git a/arch/arm64/boot/dts/freescale/imx8mm-venice-gw73xx.dtsi b/arch/arm64/boot/dts/freescale/imx8mm-venice-gw73xx.dtsi
index d2ffd62a3bd4..a59e849c7be2 100644
--- a/arch/arm64/boot/dts/freescale/imx8mm-venice-gw73xx.dtsi
+++ b/arch/arm64/boot/dts/freescale/imx8mm-venice-gw73xx.dtsi
@@ -96,7 +96,7 @@
 &ecspi2 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_spi2>;
-	cs-gpios = <&gpio5 13 GPIO_ACTIVE_HIGH>;
+	cs-gpios = <&gpio5 13 GPIO_ACTIVE_LOW>;
 	status = "okay";
 };
 
diff --git a/arch/arm64/boot/dts/freescale/imx8mm-venice-gw7901.dts b/arch/arm64/boot/dts/freescale/imx8mm-venice-gw7901.dts
index bafd5c8ea4e2..21c546c4628d 100644
--- a/arch/arm64/boot/dts/freescale/imx8mm-venice-gw7901.dts
+++ b/arch/arm64/boot/dts/freescale/imx8mm-venice-gw7901.dts
@@ -255,6 +255,10 @@
 	};
 };
 
+&disp_blk_ctrl {
+	status = "disabled";
+};
+
 &ecspi1 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_spi1>;
@@ -282,6 +286,14 @@
 	};
 };
 
+&gpu_2d {
+	status = "disabled";
+};
+
+&gpu_3d {
+	status = "disabled";
+};
+
 &i2c1 {
 	clock-frequency = <100000>;
 	pinctrl-names = "default";
@@ -632,6 +644,18 @@
 	status = "okay";
 };
 
+&pgc_gpu {
+	status = "disabled";
+};
+
+&pgc_gpumix {
+	status = "disabled";
+};
+
+&pgc_mipi {
+	status = "disabled";
+};
+
 &uart1 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_uart1>, <&pinctrl_uart1_gpio>;
diff --git a/arch/arm64/boot/dts/freescale/imx8mm.dtsi b/arch/arm64/boot/dts/freescale/imx8mm.dtsi
index 2f632e8ca388..c2f3f118f82e 100644
--- a/arch/arm64/boot/dts/freescale/imx8mm.dtsi
+++ b/arch/arm64/boot/dts/freescale/imx8mm.dtsi
@@ -7,6 +7,8 @@
 #include <dt-bindings/gpio/gpio.h>
 #include <dt-bindings/input/input.h>
 #include <dt-bindings/interrupt-controller/arm-gic.h>
+#include <dt-bindings/power/imx8mm-power.h>
+#include <dt-bindings/reset/imx8mq-reset.h>
 #include <dt-bindings/thermal/thermal.h>
 
 #include "imx8mm-pinfunc.h"
@@ -610,6 +612,111 @@
 				interrupts = <GIC_SPI 89 IRQ_TYPE_LEVEL_HIGH>;
 				#reset-cells = <1>;
 			};
+
+			gpc: gpc@303a0000 {
+				compatible = "fsl,imx8mm-gpc";
+				reg = <0x303a0000 0x10000>;
+				interrupts = <GIC_SPI 87 IRQ_TYPE_LEVEL_HIGH>;
+				interrupt-parent = <&gic>;
+				interrupt-controller;
+				#interrupt-cells = <3>;
+
+				pgc {
+					#address-cells = <1>;
+					#size-cells = <0>;
+
+					pgc_hsiomix: power-domain@0 {
+						#power-domain-cells = <0>;
+						reg = <IMX8MM_POWER_DOMAIN_HSIOMIX>;
+						clocks = <&clk IMX8MM_CLK_USB_BUS>;
+						assigned-clocks = <&clk IMX8MM_CLK_USB_BUS>;
+						assigned-clock-parents = <&clk IMX8MM_SYS_PLL2_500M>;
+					};
+
+					pgc_pcie: power-domain@1 {
+						#power-domain-cells = <0>;
+						reg = <IMX8MM_POWER_DOMAIN_PCIE>;
+						power-domains = <&pgc_hsiomix>;
+						clocks = <&clk IMX8MM_CLK_PCIE1_ROOT>;
+					};
+
+					pgc_otg1: power-domain@2 {
+						#power-domain-cells = <0>;
+						reg = <IMX8MM_POWER_DOMAIN_OTG1>;
+						power-domains = <&pgc_hsiomix>;
+					};
+
+					pgc_otg2: power-domain@3 {
+						#power-domain-cells = <0>;
+						reg = <IMX8MM_POWER_DOMAIN_OTG2>;
+						power-domains = <&pgc_hsiomix>;
+					};
+
+					pgc_gpumix: power-domain@4 {
+						#power-domain-cells = <0>;
+						reg = <IMX8MM_POWER_DOMAIN_GPUMIX>;
+						clocks = <&clk IMX8MM_CLK_GPU_BUS_ROOT>,
+							 <&clk IMX8MM_CLK_GPU_AHB>;
+						assigned-clocks = <&clk IMX8MM_CLK_GPU_AXI>,
+								  <&clk IMX8MM_CLK_GPU_AHB>;
+						assigned-clock-parents = <&clk IMX8MM_SYS_PLL1_800M>,
+									 <&clk IMX8MM_SYS_PLL1_800M>;
+						assigned-clock-rates = <800000000>, <400000000>;
+					};
+
+					pgc_gpu: power-domain@5 {
+						#power-domain-cells = <0>;
+						reg = <IMX8MM_POWER_DOMAIN_GPU>;
+						clocks = <&clk IMX8MM_CLK_GPU_AHB>,
+							 <&clk IMX8MM_CLK_GPU_BUS_ROOT>,
+							 <&clk IMX8MM_CLK_GPU2D_ROOT>,
+							 <&clk IMX8MM_CLK_GPU3D_ROOT>;
+						resets = <&src IMX8MQ_RESET_GPU_RESET>;
+						power-domains = <&pgc_gpumix>;
+					};
+
+					pgc_vpumix: power-domain@6 {
+						#power-domain-cells = <0>;
+						reg = <IMX8MM_POWER_DOMAIN_VPUMIX>;
+						clocks = <&clk IMX8MM_CLK_VPU_DEC_ROOT>;
+						assigned-clocks = <&clk IMX8MM_CLK_VPU_BUS>;
+						assigned-clock-parents = <&clk IMX8MM_SYS_PLL1_800M>;
+						resets = <&src IMX8MQ_RESET_VPU_RESET>;
+					};
+
+					pgc_vpu_g1: power-domain@7 {
+						#power-domain-cells = <0>;
+						reg = <IMX8MM_POWER_DOMAIN_VPUG1>;
+					};
+
+					pgc_vpu_g2: power-domain@8 {
+						#power-domain-cells = <0>;
+						reg = <IMX8MM_POWER_DOMAIN_VPUG2>;
+					};
+
+					pgc_vpu_h1: power-domain@9 {
+						#power-domain-cells = <0>;
+						reg = <IMX8MM_POWER_DOMAIN_VPUH1>;
+					};
+
+					pgc_dispmix: power-domain@10 {
+						#power-domain-cells = <0>;
+						reg = <IMX8MM_POWER_DOMAIN_DISPMIX>;
+						clocks = <&clk IMX8MM_CLK_DISP_APB_ROOT>,
+							 <&clk IMX8MM_CLK_DISP_AXI_ROOT>;
+						assigned-clocks = <&clk IMX8MM_CLK_DISP_AXI>,
+								  <&clk IMX8MM_CLK_DISP_APB>;
+						assigned-clock-parents = <&clk IMX8MM_SYS_PLL2_1000M>,
+									 <&clk IMX8MM_SYS_PLL1_800M>;
+						assigned-clock-rates = <500000000>, <200000000>;
+					};
+
+					pgc_mipi: power-domain@11 {
+						#power-domain-cells = <0>;
+						reg = <IMX8MM_POWER_DOMAIN_MIPI>;
+					};
+				};
+			};
 		};
 
 		aips2: bus@30400000 {
@@ -961,6 +1068,33 @@
 			#size-cells = <1>;
 			ranges = <0x32c00000 0x32c00000 0x400000>;
 
+			disp_blk_ctrl: blk-ctrl@32e28000 {
+				compatible = "fsl,imx8mm-disp-blk-ctrl", "syscon";
+				reg = <0x32e28000 0x100>;
+				power-domains = <&pgc_dispmix>, <&pgc_dispmix>,
+						<&pgc_dispmix>, <&pgc_mipi>,
+						<&pgc_mipi>;
+				power-domain-names = "bus", "csi-bridge",
+						     "lcdif", "mipi-dsi",
+						     "mipi-csi";
+				clocks = <&clk IMX8MM_CLK_DISP_AXI_ROOT>,
+					 <&clk IMX8MM_CLK_DISP_APB_ROOT>,
+					 <&clk IMX8MM_CLK_CSI1_ROOT>,
+					 <&clk IMX8MM_CLK_DISP_AXI_ROOT>,
+					 <&clk IMX8MM_CLK_DISP_APB_ROOT>,
+					 <&clk IMX8MM_CLK_DISP_ROOT>,
+					 <&clk IMX8MM_CLK_DSI_CORE>,
+					 <&clk IMX8MM_CLK_DSI_PHY_REF>,
+					 <&clk IMX8MM_CLK_CSI1_CORE>,
+					 <&clk IMX8MM_CLK_CSI1_PHY_REF>;
+				clock-names = "csi-bridge-axi","csi-bridge-apb",
+					      "csi-bridge-core", "lcdif-axi",
+					      "lcdif-apb", "lcdif-pix",
+					      "dsi-pclk", "dsi-ref",
+					      "csi-aclk", "csi-pclk";
+				#power-domain-cells = <1>;
+			};
+
 			usbotg1: usb@32e40000 {
 				compatible = "fsl,imx8mm-usb", "fsl,imx7d-usb";
 				reg = <0x32e40000 0x200>;
@@ -971,6 +1105,7 @@
 				assigned-clock-parents = <&clk IMX8MM_SYS_PLL2_500M>;
 				phys = <&usbphynop1>;
 				fsl,usbmisc = <&usbmisc1 0>;
+				power-domains = <&pgc_otg1>;
 				status = "disabled";
 			};
 
@@ -990,6 +1125,7 @@
 				assigned-clock-parents = <&clk IMX8MM_SYS_PLL2_500M>;
 				phys = <&usbphynop2>;
 				fsl,usbmisc = <&usbmisc2 0>;
+				power-domains = <&pgc_otg2>;
 				status = "disabled";
 			};
 
@@ -1030,6 +1166,50 @@
 			status = "disabled";
 		};
 
+		gpu_3d: gpu@38000000 {
+			compatible = "vivante,gc";
+			reg = <0x38000000 0x8000>;
+			interrupts = <GIC_SPI 3 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&clk IMX8MM_CLK_GPU_AHB>,
+				 <&clk IMX8MM_CLK_GPU_BUS_ROOT>,
+				 <&clk IMX8MM_CLK_GPU3D_ROOT>,
+				 <&clk IMX8MM_CLK_GPU3D_ROOT>;
+			clock-names = "reg", "bus", "core", "shader";
+			assigned-clocks = <&clk IMX8MM_CLK_GPU3D_CORE>,
+					  <&clk IMX8MM_GPU_PLL_OUT>;
+			assigned-clock-parents = <&clk IMX8MM_GPU_PLL_OUT>;
+			assigned-clock-rates = <0>, <1000000000>;
+			power-domains = <&pgc_gpu>;
+		};
+
+		gpu_2d: gpu@38008000 {
+			compatible = "vivante,gc";
+			reg = <0x38008000 0x8000>;
+			interrupts = <GIC_SPI 25 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&clk IMX8MM_CLK_GPU_AHB>,
+				 <&clk IMX8MM_CLK_GPU_BUS_ROOT>,
+				 <&clk IMX8MM_CLK_GPU2D_ROOT>;
+			clock-names = "reg", "bus", "core";
+			assigned-clocks = <&clk IMX8MM_CLK_GPU2D_CORE>,
+					  <&clk IMX8MM_GPU_PLL_OUT>;
+			assigned-clock-parents = <&clk IMX8MM_GPU_PLL_OUT>;
+			assigned-clock-rates = <0>, <1000000000>;
+			power-domains = <&pgc_gpu>;
+		};
+
+		vpu_blk_ctrl: blk-ctrl@38330000 {
+			compatible = "fsl,imx8mm-vpu-blk-ctrl", "syscon";
+			reg = <0x38330000 0x100>;
+			power-domains = <&pgc_vpumix>, <&pgc_vpu_g1>,
+					<&pgc_vpu_g2>, <&pgc_vpu_h1>;
+			power-domain-names = "bus", "g1", "g2", "h1";
+			clocks = <&clk IMX8MM_CLK_VPU_G1_ROOT>,
+				 <&clk IMX8MM_CLK_VPU_G2_ROOT>,
+				 <&clk IMX8MM_CLK_VPU_H1_ROOT>;
+			clock-names = "g1", "g2", "h1";
+			#power-domain-cells = <1>;
+		};
+
 		gic: interrupt-controller@38800000 {
 			compatible = "arm,gic-v3";
 			reg = <0x38800000 0x10000>, /* GIC Dist */
diff --git a/arch/arm64/boot/dts/freescale/imx8mp.dtsi b/arch/arm64/boot/dts/freescale/imx8mp.dtsi
index 9b07b26230a1..04d259de5667 100644
--- a/arch/arm64/boot/dts/freescale/imx8mp.dtsi
+++ b/arch/arm64/boot/dts/freescale/imx8mp.dtsi
@@ -785,7 +785,7 @@
 				interrupts = <GIC_SPI 107 IRQ_TYPE_LEVEL_HIGH>;
 				clocks = <&clk IMX8MP_CLK_QSPI_ROOT>,
 					 <&clk IMX8MP_CLK_QSPI_ROOT>;
-				clock-names = "fspi", "fspi_en";
+				clock-names = "fspi_en", "fspi";
 				assigned-clock-rates = <80000000>;
 				assigned-clocks = <&clk IMX8MP_CLK_QSPI>;
 				#address-cells = <1>;
diff --git a/arch/arm64/boot/dts/freescale/imx8mq-librem5.dtsi b/arch/arm64/boot/dts/freescale/imx8mq-librem5.dtsi
index 460ef0d86540..60d47c71499b 100644
--- a/arch/arm64/boot/dts/freescale/imx8mq-librem5.dtsi
+++ b/arch/arm64/boot/dts/freescale/imx8mq-librem5.dtsi
@@ -40,12 +40,14 @@
 			label = "VOL_DOWN";
 			gpios = <&gpio1 17 GPIO_ACTIVE_LOW>;
 			linux,code = <KEY_VOLUMEDOWN>;
+			debounce-interval = <50>;
 		};
 
 		vol-up {
 			label = "VOL_UP";
 			gpios = <&gpio1 16 GPIO_ACTIVE_LOW>;
 			linux,code = <KEY_VOLUMEUP>;
+			debounce-interval = <50>;
 		};
 	};
 
@@ -138,9 +140,14 @@
 
 	reg_wifi_3v3: regulator-wifi-3v3 {
 		compatible = "regulator-fixed";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_wifi_pwr>;
 		regulator-name = "3V3_WIFI";
 		regulator-min-microvolt = <3300000>;
 		regulator-max-microvolt = <3300000>;
+		gpio = <&gpio3 10 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+		vin-supply = <&reg_vdd_3v3>;
 	};
 
 	sound {
@@ -193,6 +200,14 @@
 		};
 	};
 
+	usdhc2_pwrseq: pwrseq {
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_bt>, <&pinctrl_wifi_disable>;
+		compatible = "mmc-pwrseq-simple";
+		reset-gpios = <&gpio3 25 GPIO_ACTIVE_HIGH>,
+			      <&gpio4 29 GPIO_ACTIVE_HIGH>;
+	};
+
 	bm818_codec: sound-wwan-codec {
 		compatible = "broadmobi,bm818", "option,gtm601";
 		#sound-dai-cells = <0>;
@@ -225,7 +240,7 @@
 &ddrc {
 	operating-points-v2 = <&ddrc_opp_table>;
 
-	ddrc_opp_table: ddrc-opp-table {
+	ddrc_opp_table: opp-table {
 		compatible = "operating-points-v2";
 
 		opp-25M {
@@ -307,6 +322,13 @@
 		>;
 	};
 
+	pinctrl_bt: btgrp {
+		fsl,pins = <
+			/* BT_REG_ON */
+			MX8MQ_IOMUXC_SAI5_MCLK_GPIO3_IO25	0x83
+		>;
+	};
+
 	pinctrl_charger_in: chargeringrp {
 		fsl,pins = <
 			/* CHRG_INT */
@@ -638,6 +660,20 @@
 		>;
 	};
 
+	pinctrl_wifi_disable: wifidisablegrp {
+		fsl,pins = <
+			/* WIFI_REG_ON */
+			MX8MQ_IOMUXC_SAI3_RXC_GPIO4_IO29	0x83
+		>;
+	};
+
+	pinctrl_wifi_pwr: wifipwrgrp {
+		fsl,pins = <
+			/* WIFI3V3_EN */
+			MX8MQ_IOMUXC_NAND_DATA04_GPIO3_IO10	0x83
+		>;
+	};
+
 	pinctrl_wdog: wdoggrp {
 		fsl,pins = <
 			/* nWDOG */
@@ -1010,6 +1046,7 @@
 		vddi-supply = <&reg_lcd_1v8>;
 		backlight = <&backlight_dsi>;
 		reset-gpios = <&gpio1 29 GPIO_ACTIVE_LOW>;
+		mantix,tp-rstn-gpios = <&gpio1 24 GPIO_ACTIVE_LOW>;
 
 		port {
 			panel_in: endpoint {
@@ -1055,13 +1092,13 @@
 
 &pwm3 {
 	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_led_g>;
+	pinctrl-0 = <&pinctrl_led_r>;
 	status = "okay";
 };
 
 &pwm4 {
 	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_led_r>;
+	pinctrl-0 = <&pinctrl_led_g>;
 	status = "okay";
 };
 
@@ -1199,7 +1236,10 @@
 	pinctrl-2 = <&pinctrl_usdhc2_200mhz>;
 	bus-width = <4>;
 	vmmc-supply = <&reg_wifi_3v3>;
+	mmc-pwrseq = <&usdhc2_pwrseq>;
+	post-power-on-delay-ms = <1000>;
 	cd-gpios = <&gpio2 12 GPIO_ACTIVE_LOW>;
+	max-frequency = <50000000>;
 	disable-wp;
 	cap-sdio-irq;
 	keep-power-in-suspend;
diff --git a/arch/arm64/boot/dts/freescale/imx8mq-mnt-reform2.dts b/arch/arm64/boot/dts/freescale/imx8mq-mnt-reform2.dts
index 2535268f0984..4f2db6197b39 100644
--- a/arch/arm64/boot/dts/freescale/imx8mq-mnt-reform2.dts
+++ b/arch/arm64/boot/dts/freescale/imx8mq-mnt-reform2.dts
@@ -202,6 +202,7 @@
 
 	pinctrl_usdhc2: usdhc2grp {
 		fsl,pins = <
+			MX8MQ_IOMUXC_SD2_CD_B_USDHC2_CD_B		0x0
 			MX8MQ_IOMUXC_SD2_CLK_USDHC2_CLK			0x83
 			MX8MQ_IOMUXC_SD2_CMD_USDHC2_CMD			0xc3
 			MX8MQ_IOMUXC_SD2_DATA0_USDHC2_DATA0		0xc3
diff --git a/arch/arm64/boot/dts/freescale/imx8mq-zii-ultra.dtsi b/arch/arm64/boot/dts/freescale/imx8mq-zii-ultra.dtsi
index a08a568c31d9..2222ef7b3eab 100644
--- a/arch/arm64/boot/dts/freescale/imx8mq-zii-ultra.dtsi
+++ b/arch/arm64/boot/dts/freescale/imx8mq-zii-ultra.dtsi
@@ -555,6 +555,7 @@
 	         <&clk IMX8MQ_CLK_PCIE1_PHY>,
 	         <&pcie0_refclk>;
 	clock-names = "pcie", "pcie_aux", "pcie_phy", "pcie_bus";
+	vph-supply = <&vgen5_reg>;
 	status = "okay";
 };
 
@@ -567,6 +568,7 @@
 	         <&clk IMX8MQ_CLK_PCIE2_PHY>,
 	         <&pcie1_refclk>;
 	clock-names = "pcie", "pcie_aux", "pcie_phy", "pcie_bus";
+	vph-supply = <&vgen5_reg>;
 	status = "okay";
 };
 
diff --git a/arch/arm64/boot/dts/freescale/imx8mq.dtsi b/arch/arm64/boot/dts/freescale/imx8mq.dtsi
index 4066b1612655..972766b67a15 100644
--- a/arch/arm64/boot/dts/freescale/imx8mq.dtsi
+++ b/arch/arm64/boot/dts/freescale/imx8mq.dtsi
@@ -1467,10 +1467,9 @@
 			#size-cells = <2>;
 			device_type = "pci";
 			bus-range = <0x00 0xff>;
-			ranges = <0x81000000 0 0x00000000 0x1ff80000 0 0x00010000 /* downstream I/O 64KB */
-			          0x82000000 0 0x18000000 0x18000000 0 0x07f00000>; /* non-prefetchable memory */
+			ranges = <0x81000000 0 0x00000000 0x1ff80000 0 0x00010000>, /* downstream I/O 64KB */
+				 <0x82000000 0 0x18000000 0x18000000 0 0x07f00000>; /* non-prefetchable memory */
 			num-lanes = <1>;
-			num-viewport = <4>;
 			interrupts = <GIC_SPI 122 IRQ_TYPE_LEVEL_HIGH>;
 			interrupt-names = "msi";
 			#interrupt-cells = <1>;
@@ -1505,10 +1504,9 @@
 			#address-cells = <3>;
 			#size-cells = <2>;
 			device_type = "pci";
-			ranges =  <0x81000000 0 0x00000000 0x27f80000 0 0x00010000 /* downstream I/O 64KB */
-				   0x82000000 0 0x20000000 0x20000000 0 0x07f00000>; /* non-prefetchable memory */
+			ranges =  <0x81000000 0 0x00000000 0x27f80000 0 0x00010000>, /* downstream I/O 64KB */
+				  <0x82000000 0 0x20000000 0x20000000 0 0x07f00000>; /* non-prefetchable memory */
 			num-lanes = <1>;
-			num-viewport = <4>;
 			interrupts = <GIC_SPI 74 IRQ_TYPE_LEVEL_HIGH>;
 			interrupt-names = "msi";
 			#interrupt-cells = <1>;
diff --git a/arch/arm64/boot/dts/freescale/s32g2.dtsi b/arch/arm64/boot/dts/freescale/s32g2.dtsi
new file mode 100644
index 000000000000..59ea8a25aa4c
--- /dev/null
+++ b/arch/arm64/boot/dts/freescale/s32g2.dtsi
@@ -0,0 +1,124 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/*
+ * NXP S32G2 SoC family
+ *
+ * Copyright (c) 2021 SUSE LLC
+ * Copyright (c) 2017-2021 NXP
+ */
+
+#include <dt-bindings/interrupt-controller/arm-gic.h>
+
+/ {
+	compatible = "nxp,s32g2";
+	interrupt-parent = <&gic>;
+	#address-cells = <2>;
+	#size-cells = <2>;
+
+	cpus {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		cpu0: cpu@0 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a53";
+			reg = <0x0>;
+			enable-method = "psci";
+			next-level-cache = <&cluster0_l2>;
+		};
+
+		cpu1: cpu@1 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a53";
+			reg = <0x1>;
+			enable-method = "psci";
+			next-level-cache = <&cluster0_l2>;
+		};
+
+		cpu2: cpu@100 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a53";
+			reg = <0x100>;
+			enable-method = "psci";
+			next-level-cache = <&cluster1_l2>;
+		};
+
+		cpu3: cpu@101 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a53";
+			reg = <0x101>;
+			enable-method = "psci";
+			next-level-cache = <&cluster1_l2>;
+		};
+
+		cluster0_l2: l2-cache0 {
+			compatible = "cache";
+		};
+
+		cluster1_l2: l2-cache1 {
+			compatible = "cache";
+		};
+	};
+
+	pmu {
+		compatible = "arm,cortex-a53-pmu";
+		interrupts = <GIC_PPI 7 IRQ_TYPE_LEVEL_HIGH>;
+	};
+
+	timer {
+		compatible = "arm,armv8-timer";
+		interrupts = <GIC_PPI 13 IRQ_TYPE_LEVEL_LOW>,
+			     <GIC_PPI 14 IRQ_TYPE_LEVEL_LOW>,
+			     <GIC_PPI 11 IRQ_TYPE_LEVEL_LOW>,
+			     <GIC_PPI 10 IRQ_TYPE_LEVEL_LOW>;
+	};
+
+	firmware {
+		psci {
+			compatible = "arm,psci-1.0";
+			method = "smc";
+		};
+	};
+
+	soc {
+		compatible = "simple-bus";
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges = <0 0 0 0x80000000>;
+
+		uart0: serial@401c8000 {
+			compatible = "nxp,s32g2-linflexuart",
+				     "fsl,s32v234-linflexuart";
+			reg = <0x401c8000 0x3000>;
+			interrupts = <GIC_SPI 82 IRQ_TYPE_EDGE_RISING>;
+			status = "disabled";
+		};
+
+		uart1: serial@401cc000 {
+			compatible = "nxp,s32g2-linflexuart",
+				     "fsl,s32v234-linflexuart";
+			reg = <0x401cc000 0x3000>;
+			interrupts = <GIC_SPI 83 IRQ_TYPE_EDGE_RISING>;
+			status = "disabled";
+		};
+
+		uart2: serial@402bc000 {
+			compatible = "nxp,s32g2-linflexuart",
+				     "fsl,s32v234-linflexuart";
+			reg = <0x402bc000 0x3000>;
+			interrupts = <GIC_SPI 84 IRQ_TYPE_EDGE_RISING>;
+			status = "disabled";
+		};
+
+		gic: interrupt-controller@50800000 {
+			compatible = "arm,gic-v3";
+			reg = <0x50800000 0x10000>,
+			      <0x50880000 0x80000>,
+			      <0x50400000 0x2000>,
+			      <0x50410000 0x2000>,
+			      <0x50420000 0x2000>;
+			interrupts = <GIC_PPI 9 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-controller;
+			#interrupt-cells = <3>;
+		};
+	};
+};
diff --git a/arch/arm64/boot/dts/freescale/s32g274a-evb.dts b/arch/arm64/boot/dts/freescale/s32g274a-evb.dts
new file mode 100644
index 000000000000..9118d8d2ee01
--- /dev/null
+++ b/arch/arm64/boot/dts/freescale/s32g274a-evb.dts
@@ -0,0 +1,34 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/*
+ * Copyright (c) 2021 SUSE LLC
+ * Copyright (c) 2019-2021 NXP
+ */
+
+/dts-v1/;
+
+#include "s32g2.dtsi"
+
+/ {
+	model = "NXP S32G2 Evaluation Board (S32G-VNP-EVB)";
+	compatible = "nxp,s32g274a-evb", "nxp,s32g2";
+
+	aliases {
+		serial0 = &uart0;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	/* 4GiB RAM */
+	memory@80000000 {
+		device_type = "memory";
+		reg = <0x0 0x80000000 0 0x80000000>,
+		      <0x8 0x80000000 0 0x80000000>;
+	};
+};
+
+/* UART (J58) to Micro USB port */
+&uart0 {
+	status = "okay";
+};
diff --git a/arch/arm64/boot/dts/freescale/s32g274a-rdb2.dts b/arch/arm64/boot/dts/freescale/s32g274a-rdb2.dts
new file mode 100644
index 000000000000..e05ee854cdf5
--- /dev/null
+++ b/arch/arm64/boot/dts/freescale/s32g274a-rdb2.dts
@@ -0,0 +1,40 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/*
+ * Copyright (c) 2021 SUSE LLC
+ * Copyright (c) 2019-2021 NXP
+ */
+
+/dts-v1/;
+
+#include "s32g2.dtsi"
+
+/ {
+	model = "NXP S32G2 Reference Design Board 2 (S32G-VNP-RDB2)";
+	compatible = "nxp,s32g274a-rdb2", "nxp,s32g2";
+
+	aliases {
+		serial0 = &uart0;
+		serial1 = &uart1;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	/* 4GiB RAM */
+	memory@80000000 {
+		device_type = "memory";
+		reg = <0x0 0x80000000 0 0x80000000>,
+		      <0x8 0x80000000 0 0x80000000>;
+	};
+};
+
+/* UART (J2) to Micro USB port */
+&uart0 {
+	status = "okay";
+};
+
+/* UART (J1) to Micro USB port */
+&uart1 {
+	status = "okay";
+};
diff --git a/arch/arm64/boot/dts/hisilicon/hi3660.dtsi b/arch/arm64/boot/dts/hisilicon/hi3660.dtsi
index 2d5c1a348716..8bd6d7e8a474 100644
--- a/arch/arm64/boot/dts/hisilicon/hi3660.dtsi
+++ b/arch/arm64/boot/dts/hisilicon/hi3660.dtsi
@@ -210,7 +210,7 @@
 		};
 	};
 
-	cluster0_opp: opp_table0 {
+	cluster0_opp: opp-table-0 {
 		compatible = "operating-points-v2";
 		opp-shared;
 
@@ -245,7 +245,7 @@
 		};
 	};
 
-	cluster1_opp: opp_table1 {
+	cluster1_opp: opp-table-1 {
 		compatible = "operating-points-v2";
 		opp-shared;
 
@@ -1087,7 +1087,7 @@
 		};
 
 		watchdog0: watchdog@e8a06000 {
-			compatible = "arm,sp805-wdt", "arm,primecell";
+			compatible = "arm,sp805", "arm,primecell";
 			reg = <0x0 0xe8a06000 0x0 0x1000>;
 			interrupts = <GIC_SPI 44 IRQ_TYPE_LEVEL_HIGH>;
 			clocks = <&crg_ctrl HI3660_OSC32K>,
@@ -1096,7 +1096,7 @@
 		};
 
 		watchdog1: watchdog@e8a07000 {
-			compatible = "arm,sp805-wdt", "arm,primecell";
+			compatible = "arm,sp805", "arm,primecell";
 			reg = <0x0 0xe8a07000 0x0 0x1000>;
 			interrupts = <GIC_SPI 45 IRQ_TYPE_LEVEL_HIGH>;
 			clocks = <&crg_ctrl HI3660_OSC32K>,
diff --git a/arch/arm64/boot/dts/hisilicon/hi3670-hikey970.dts b/arch/arm64/boot/dts/hisilicon/hi3670-hikey970.dts
index d8abf442ee7e..7c32f5fd5cc5 100644
--- a/arch/arm64/boot/dts/hisilicon/hi3670-hikey970.dts
+++ b/arch/arm64/boot/dts/hisilicon/hi3670-hikey970.dts
@@ -12,6 +12,7 @@
 
 #include "hi3670.dtsi"
 #include "hikey970-pinctrl.dtsi"
+#include "hikey970-pmic.dtsi"
 
 / {
 	model = "HiKey970";
@@ -39,23 +40,6 @@
 		reg = <0x0 0x0 0x0 0x0>;
 	};
 
-	sd_1v8: regulator-1v8 {
-		compatible = "regulator-fixed";
-		regulator-name = "fixed-1.8V";
-		regulator-min-microvolt = <1800000>;
-		regulator-max-microvolt = <1800000>;
-		regulator-always-on;
-	};
-
-	sd_3v3: regulator-3v3 {
-		compatible = "regulator-fixed";
-		regulator-name = "fixed-3.3V";
-		regulator-min-microvolt = <3300000>;
-		regulator-max-microvolt = <3300000>;
-		regulator-boot-on;
-		regulator-always-on;
-	};
-
 	wlan_en: wlan-en-1-8v {
 		compatible = "regulator-fixed";
 		regulator-name = "wlan-en-regulator";
@@ -402,8 +386,8 @@
 	pinctrl-0 = <&sd_pmx_func
 		     &sd_clk_cfg_func
 		     &sd_cfg_func>;
-	vmmc-supply = <&sd_3v3>;
-	vqmmc-supply = <&sd_1v8>;
+	vmmc-supply = <&ldo16>;
+	vqmmc-supply = <&ldo9>;
 	status = "okay";
 };
 
diff --git a/arch/arm64/boot/dts/hisilicon/hi3670.dtsi b/arch/arm64/boot/dts/hisilicon/hi3670.dtsi
index 20698cfd0637..636c8817df7e 100644
--- a/arch/arm64/boot/dts/hisilicon/hi3670.dtsi
+++ b/arch/arm64/boot/dts/hisilicon/hi3670.dtsi
@@ -669,7 +669,7 @@
 			interrupt-parent = <&gic>;
 			interrupts = <GIC_SPI 278 IRQ_TYPE_LEVEL_HIGH>;
 			clocks = <&crg_ctrl HI3670_CLK_GATE_UFSIO_REF>,
-				<&crg_ctrl HI3670_CLK_GATE_UFS_SUBSYS>;
+				 <&crg_ctrl HI3670_CLK_GATE_UFS_SUBSYS>;
 			clock-names = "ref_clk", "phy_clk";
 			freq-table-hz = <0 0
 					 0 0>;
diff --git a/arch/arm64/boot/dts/hisilicon/hi6220.dtsi b/arch/arm64/boot/dts/hisilicon/hi6220.dtsi
index dde9371dc545..ae0a7cfeeb47 100644
--- a/arch/arm64/boot/dts/hisilicon/hi6220.dtsi
+++ b/arch/arm64/boot/dts/hisilicon/hi6220.dtsi
@@ -193,7 +193,7 @@
 		};
 	};
 
-	cpu_opp_table: cpu_opp_table {
+	cpu_opp_table: opp-table-0 {
 		compatible = "operating-points-v2";
 		opp-shared;
 
@@ -840,7 +840,7 @@
 		};
 
 		watchdog0: watchdog@f8005000 {
-			compatible = "arm,sp805-wdt", "arm,primecell";
+			compatible = "arm,sp805", "arm,primecell";
 			reg = <0x0 0xf8005000 0x0 0x1000>;
 			interrupts = <GIC_SPI 13 IRQ_TYPE_LEVEL_HIGH>;
 			clocks = <&ao_ctrl HI6220_WDT0_PCLK>,
diff --git a/arch/arm64/boot/dts/hisilicon/hikey970-pmic.dtsi b/arch/arm64/boot/dts/hisilicon/hikey970-pmic.dtsi
new file mode 100644
index 000000000000..970047f2dabd
--- /dev/null
+++ b/arch/arm64/boot/dts/hisilicon/hikey970-pmic.dtsi
@@ -0,0 +1,86 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * dts file for Hi6421v600 SPMI PMIC used at the HiKey970 Development Board
+ *
+ * Copyright (C) 2020, Huawei Tech. Co., Ltd.
+ */
+
+#include <dt-bindings/spmi/spmi.h>
+
+/ {
+	spmi: spmi@fff24000 {
+		compatible = "hisilicon,kirin970-spmi-controller";
+		#address-cells = <2>;
+		#size-cells = <0>;
+		status = "okay";
+		reg = <0x0 0xfff24000 0x0 0x1000>;
+		hisilicon,spmi-channel = <2>;
+
+		pmic: pmic@0 {
+			compatible = "hisilicon,hi6421-spmi";
+			reg = <0 SPMI_USID>;
+
+			#interrupt-cells = <2>;
+			interrupt-controller;
+			gpios = <&gpio28 0 0>;
+
+			regulators {
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				ldo3: ldo3 { /* HDMI */
+					regulator-name = "ldo3";
+					regulator-min-microvolt = <1500000>;
+					regulator-max-microvolt = <2000000>;
+					regulator-boot-on;
+				};
+
+				ldo4: ldo4 { /* 40 PIN */
+					regulator-name = "ldo4";
+					regulator-min-microvolt = <1725000>;
+					regulator-max-microvolt = <1900000>;
+					regulator-boot-on;
+				};
+
+				ldo9: ldo9 { /* SDCARD I/O */
+					regulator-name = "ldo9";
+					regulator-min-microvolt = <1750000>;
+					regulator-max-microvolt = <3300000>;
+					regulator-boot-on;
+				};
+
+				ldo15: ldo15 { /* UFS */
+					regulator-name = "ldo15";
+					regulator-min-microvolt = <1800000>;
+					regulator-max-microvolt = <3000000>;
+					regulator-always-on;
+				};
+
+				ldo16: ldo16 { /* SD */
+					regulator-name = "ldo16";
+					regulator-min-microvolt = <1800000>;
+					regulator-max-microvolt = <3000000>;
+					regulator-boot-on;
+				};
+
+				ldo17: ldo17 { /* USB HUB */
+					regulator-name = "ldo17";
+					regulator-min-microvolt = <2500000>;
+					regulator-max-microvolt = <3300000>;
+				};
+
+				ldo33: ldo33 { /* PEX8606 */
+					regulator-name = "ldo33";
+					regulator-min-microvolt = <2500000>;
+					regulator-max-microvolt = <3300000>;
+				};
+
+				ldo34: ldo34 { /* GPS AUX IN VDD */
+					regulator-name = "ldo34";
+					regulator-min-microvolt = <2600000>;
+					regulator-max-microvolt = <3300000>;
+				};
+			};
+		};
+	};
+};
diff --git a/arch/arm64/boot/dts/marvell/Makefile b/arch/arm64/boot/dts/marvell/Makefile
index c686a8dd3ca5..1c794cdcb8e6 100644
--- a/arch/arm64/boot/dts/marvell/Makefile
+++ b/arch/arm64/boot/dts/marvell/Makefile
@@ -9,6 +9,7 @@ dtb-$(CONFIG_ARCH_MVEBU) += armada-3720-espressobin-v7-emmc.dtb
 dtb-$(CONFIG_ARCH_MVEBU) += armada-3720-turris-mox.dtb
 dtb-$(CONFIG_ARCH_MVEBU) += armada-3720-uDPU.dtb
 dtb-$(CONFIG_ARCH_MVEBU) += armada-7040-db.dtb
+dtb-$(CONFIG_ARCH_MVEBU) += armada-7040-mochabin.dtb
 dtb-$(CONFIG_ARCH_MVEBU) += armada-8040-clearfog-gt-8k.dtb
 dtb-$(CONFIG_ARCH_MVEBU) += armada-8040-db.dtb
 dtb-$(CONFIG_ARCH_MVEBU) += armada-8040-mcbin.dtb
diff --git a/arch/arm64/boot/dts/marvell/armada-7040-mochabin.dts b/arch/arm64/boot/dts/marvell/armada-7040-mochabin.dts
new file mode 100644
index 000000000000..f3b0d57a24a3
--- /dev/null
+++ b/arch/arm64/boot/dts/marvell/armada-7040-mochabin.dts
@@ -0,0 +1,458 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/*
+ * Device Tree file for Globalscale MOCHAbin
+ * Copyright (C) 2019 Globalscale technologies, Inc.
+ * Copyright (C) 2021 Sartura Ltd.
+ *
+ */
+
+/dts-v1/;
+
+#include <dt-bindings/gpio/gpio.h>
+#include "armada-7040.dtsi"
+
+/ {
+	model = "Globalscale MOCHAbin";
+	compatible = "globalscale,mochabin", "marvell,armada7040",
+		     "marvell,armada-ap806-quad", "marvell,armada-ap806";
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	aliases {
+		ethernet0 = &cp0_eth0;
+		ethernet1 = &cp0_eth1;
+		ethernet2 = &cp0_eth2;
+		ethernet3 = &swport1;
+		ethernet4 = &swport2;
+		ethernet5 = &swport3;
+		ethernet6 = &swport4;
+	};
+
+	/* SFP+ 10G */
+	sfp_eth0: sfp-eth0 {
+		compatible = "sff,sfp";
+		i2c-bus = <&cp0_i2c1>;
+		los-gpio = <&sfp_gpio 3 GPIO_ACTIVE_HIGH>;
+		mod-def0-gpio = <&sfp_gpio 2 GPIO_ACTIVE_LOW>;
+		tx-disable-gpio = <&sfp_gpio 1 GPIO_ACTIVE_HIGH>;
+		tx-fault-gpio  = <&sfp_gpio 0 GPIO_ACTIVE_HIGH>;
+	};
+
+	/* SFP 1G */
+	sfp_eth2: sfp-eth2 {
+		compatible = "sff,sfp";
+		i2c-bus = <&cp0_i2c0>;
+		los-gpio = <&sfp_gpio 7 GPIO_ACTIVE_HIGH>;
+		mod-def0-gpio = <&sfp_gpio 6 GPIO_ACTIVE_LOW>;
+		tx-disable-gpio = <&sfp_gpio 5 GPIO_ACTIVE_HIGH>;
+		tx-fault-gpio  = <&sfp_gpio 4 GPIO_ACTIVE_HIGH>;
+	};
+};
+
+/* microUSB UART console */
+&uart0 {
+	status = "okay";
+
+	pinctrl-0 = <&uart0_pins>;
+	pinctrl-names = "default";
+};
+
+/* eMMC */
+&ap_sdhci0 {
+	status = "okay";
+
+	bus-width = <4>;
+	non-removable;
+	/delete-property/ marvell,xenon-phy-slow-mode;
+	no-1-8-v;
+};
+
+&cp0_pinctrl {
+	cp0_uart0_pins: cp0-uart0-pins {
+		marvell,pins = "mpp6", "mpp7";
+		marvell,function = "uart0";
+	};
+
+	cp0_spi0_pins: cp0-spi0-pins {
+		marvell,pins = "mpp56", "mpp57", "mpp58", "mpp59";
+		marvell,function = "spi0";
+	};
+
+	cp0_spi1_pins: cp0-spi1-pins {
+		marvell,pins = "mpp13", "mpp14", "mpp15", "mpp16";
+		marvell,function = "spi1";
+	};
+
+	cp0_i2c0_pins: cp0-i2c0-pins {
+		marvell,pins = "mpp37", "mpp38";
+		marvell,function = "i2c0";
+	};
+
+	cp0_i2c1_pins: cp0-i2c1-pins {
+		marvell,pins = "mpp2", "mpp3";
+		marvell,function = "i2c1";
+	};
+
+	pca9554_int_pins: pca9554-int-pins {
+		marvell,pins = "mpp27";
+		marvell,function = "gpio";
+	};
+
+	cp0_rgmii1_pins: cp0-rgmii1-pins {
+		marvell,pins = "mpp44", "mpp45", "mpp46", "mpp47", "mpp48", "mpp49",
+			       "mpp50", "mpp51", "mpp52", "mpp53", "mpp54", "mpp55";
+		marvell,function = "ge1";
+	};
+
+	is31_sdb_pins: is31-sdb-pins {
+		marvell,pins = "mpp30";
+		marvell,function = "gpio";
+	};
+
+	cp0_pcie_reset_pins: cp0-pcie-reset-pins {
+		marvell,pins = "mpp9";
+		marvell,function = "gpio";
+	};
+
+	cp0_pcie_clkreq_pins: cp0-pcie-clkreq-pins {
+		marvell,pins = "mpp5";
+		marvell,function = "pcie1";
+	};
+
+	cp0_switch_pins: cp0-switch-pins {
+		marvell,pins = "mpp0", "mpp1";
+		marvell,function = "gpio";
+	};
+
+	cp0_phy_pins: cp0-phy-pins {
+		marvell,pins = "mpp12";
+		marvell,function = "gpio";
+	};
+};
+
+/* mikroBUS UART */
+&cp0_uart0 {
+	status = "okay";
+
+	pinctrl-names = "default";
+	pinctrl-0 = <&cp0_uart0_pins>;
+};
+
+/* mikroBUS SPI */
+&cp0_spi0 {
+	status = "okay";
+
+	pinctrl-names = "default";
+	pinctrl-0 = <&cp0_spi0_pins>;
+};
+
+/* SPI-NOR */
+&cp0_spi1{
+	status = "okay";
+
+	pinctrl-names = "default";
+	pinctrl-0 = <&cp0_spi1_pins>;
+
+	spi-flash@0 {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		compatible = "jedec,spi-nor";
+		reg = <0>;
+		spi-max-frequency = <20000000>;
+
+		partitions {
+			compatible = "fixed-partitions";
+			#address-cells = <1>;
+			#size-cells = <1>;
+
+			partition@0 {
+				label = "firmware";
+				reg = <0x0 0x3e0000>;
+				read-only;
+			};
+
+			partition@3e0000 {
+				label = "hw-info";
+				reg = <0x3e0000 0x10000>;
+				read-only;
+			};
+
+			partition@3f0000 {
+				label = "u-boot-env";
+				reg = <0x3f0000 0x10000>;
+			};
+		};
+	};
+};
+
+/* mikroBUS, 1G SFP and GPIO expander */
+&cp0_i2c0 {
+	status = "okay";
+
+	pinctrl-names = "default";
+	pinctrl-0 = <&cp0_i2c0_pins>;
+	clock-frequency = <100000>;
+
+	sfp_gpio: pca9554@39 {
+		compatible = "nxp,pca9554";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pca9554_int_pins>;
+		reg = <0x39>;
+
+		interrupt-parent = <&cp0_gpio1>;
+		interrupts = <27 IRQ_TYPE_LEVEL_LOW>;
+		interrupt-controller;
+		#interrupt-cells = <2>;
+
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		/*
+		 * IO0_0: SFP+_TX_FAULT
+		 * IO0_1: SFP+_TX_DISABLE
+		 * IO0_2: SFP+_PRSNT
+		 * IO0_3: SFP+_LOSS
+		 * IO0_4: SFP_TX_FAULT
+		 * IO0_5: SFP_TX_DISABLE
+		 * IO0_6: SFP_PRSNT
+		 * IO0_7: SFP_LOSS
+		 */
+	};
+};
+
+/* IS31FL3199, mini-PCIe and 10G SFP+ */
+&cp0_i2c1 {
+	status = "okay";
+
+	pinctrl-names = "default";
+	pinctrl-0 = <&cp0_i2c1_pins>;
+	clock-frequency = <100000>;
+
+	leds@64 {
+		compatible = "issi,is31fl3199";
+		#address-cells = <1>;
+		#size-cells = <0>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&is31_sdb_pins>;
+		shutdown-gpios = <&cp0_gpio1 30 GPIO_ACTIVE_HIGH>;
+		reg = <0x64>;
+
+		led1_red: led@1 {
+			label = "red:led1";
+			reg = <1>;
+			led-max-microamp = <20000>;
+		};
+
+		led1_green: led@2 {
+			label = "green:led1";
+			reg = <2>;
+		};
+
+		led1_blue: led@3 {
+			label = "blue:led1";
+			reg = <3>;
+		};
+
+		led2_red: led@4 {
+			label = "red:led2";
+			reg = <4>;
+		};
+
+		led2_green: led@5 {
+			label = "green:led2";
+			reg = <5>;
+		};
+
+		led2_blue: led@6 {
+			label = "blue:led2";
+			reg = <6>;
+		};
+
+		led3_red: led@7 {
+			label = "red:led3";
+			reg = <7>;
+		};
+
+		led3_green: led@8 {
+			label = "green:led3";
+			reg = <8>;
+		};
+
+		led3_blue: led@9 {
+			label = "blue:led3";
+			reg = <9>;
+		};
+	};
+};
+
+&cp0_mdio {
+	status = "okay";
+
+	/* 88E1512 PHY */
+	eth2phy: ethernet-phy@1 {
+		reg = <1>;
+		sfp = <&sfp_eth2>;
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&cp0_phy_pins>;
+		reset-gpios = <&cp0_gpio1 12 GPIO_ACTIVE_LOW>;
+	};
+
+	/* 88E6141 Topaz switch */
+	switch: switch@3 {
+		compatible = "marvell,mv88e6085";
+		#address-cells = <1>;
+		#size-cells = <0>;
+		reg = <3>;
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&cp0_switch_pins>;
+		reset-gpios = <&cp0_gpio1 0 GPIO_ACTIVE_LOW>;
+
+		interrupt-parent = <&cp0_gpio1>;
+		interrupts = <1 IRQ_TYPE_LEVEL_LOW>;
+
+		ports {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			swport1: port@1 {
+				reg = <1>;
+				label = "lan0";
+				phy-handle = <&swphy1>;
+			};
+
+			swport2: port@2 {
+				reg = <2>;
+				label = "lan1";
+				phy-handle = <&swphy2>;
+			};
+
+			swport3: port@3 {
+				reg = <3>;
+				label = "lan2";
+				phy-handle = <&swphy3>;
+			};
+
+			swport4: port@4 {
+				reg = <4>;
+				label = "lan3";
+				phy-handle = <&swphy4>;
+			};
+
+			port@5 {
+				reg = <5>;
+				label = "cpu";
+				ethernet = <&cp0_eth1>;
+				phy-mode = "2500base-x";
+				managed = "in-band-status";
+			};
+		};
+
+		mdio {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			swphy1: swphy1@17 {
+				reg = <17>;
+			};
+
+			swphy2: swphy2@18 {
+				reg = <18>;
+			};
+
+			swphy3: swphy3@19 {
+				reg = <19>;
+			};
+
+			swphy4: swphy4@20 {
+				reg = <20>;
+			};
+		};
+	};
+};
+
+&cp0_ethernet {
+	status = "okay";
+};
+
+/* 10G SFP+ */
+&cp0_eth0 {
+	status = "okay";
+
+	phy-mode = "10gbase-r";
+	phys = <&cp0_comphy4 0>;
+	managed = "in-band-status";
+	sfp = <&sfp_eth0>;
+};
+
+/* Topaz switch uplink */
+&cp0_eth1 {
+	status = "okay";
+
+	phy-mode = "2500base-x";
+	phys = <&cp0_comphy0 1>;
+
+	fixed-link {
+		speed = <2500>;
+		full-duplex;
+	};
+};
+
+/* 1G SFP or 1G RJ45 */
+&cp0_eth2 {
+	status = "okay";
+
+	pinctrl-names = "default";
+	pinctrl-0 = <&cp0_rgmii1_pins>;
+
+	phy = <&eth2phy>;
+	phy-mode = "rgmii-id";
+};
+
+&cp0_utmi {
+	status = "okay";
+};
+
+/* SMSC USB5434B hub */
+&cp0_usb3_0 {
+	status = "okay";
+
+	phys = <&cp0_comphy1 0>, <&cp0_utmi0>;
+	phy-names = "cp0-usb3h0-comphy", "utmi";
+};
+
+/* miniPCI-E USB */
+&cp0_usb3_1 {
+	status = "okay";
+};
+
+&cp0_sata0 {
+	status = "okay";
+
+	/* 7 + 12 SATA connector (J24) */
+	sata-port@0 {
+		phys = <&cp0_comphy2 0>;
+		phy-names = "cp0-sata0-0-phy";
+	};
+
+	/* M.2-2250 B-key (J39) */
+	sata-port@1 {
+		phys = <&cp0_comphy3 1>;
+		phy-names = "cp0-sata0-1-phy";
+	};
+};
+
+/* miniPCI-E (J5) */
+&cp0_pcie2 {
+	status = "okay";
+
+	pinctrl-names = "default", "clkreq";
+	pinctrl-0 = <&cp0_pcie_reset_pins>;
+	pinctrl-1 = <&cp0_pcie_clkreq_pins>;
+	phys = <&cp0_comphy5 2>;
+	phy-names = "cp0-pcie2-x1-phy";
+	reset-gpios = <&cp0_gpio1 9 GPIO_ACTIVE_LOW>;
+};
diff --git a/arch/arm64/boot/dts/mediatek/mt2712e.dtsi b/arch/arm64/boot/dts/mediatek/mt2712e.dtsi
index a9cca9c146fd..de16c0d80c30 100644
--- a/arch/arm64/boot/dts/mediatek/mt2712e.dtsi
+++ b/arch/arm64/boot/dts/mediatek/mt2712e.dtsi
@@ -915,64 +915,67 @@
 		};
 	};
 
-	pcie: pcie@11700000 {
+	pcie1: pcie@112ff000 {
 		compatible = "mediatek,mt2712-pcie";
 		device_type = "pci";
-		reg = <0 0x11700000 0 0x1000>,
-		      <0 0x112ff000 0 0x1000>;
-		reg-names = "port0", "port1";
+		reg = <0 0x112ff000 0 0x1000>;
+		reg-names = "port1";
+		linux,pci-domain = <1>;
 		#address-cells = <3>;
 		#size-cells = <2>;
-		interrupts = <GIC_SPI 115 IRQ_TYPE_LEVEL_HIGH>,
-			     <GIC_SPI 117 IRQ_TYPE_LEVEL_HIGH>;
-		clocks = <&topckgen CLK_TOP_PE2_MAC_P0_SEL>,
-			 <&topckgen CLK_TOP_PE2_MAC_P1_SEL>,
-			 <&pericfg CLK_PERI_PCIE0>,
+		interrupts = <GIC_SPI 117 IRQ_TYPE_LEVEL_HIGH>;
+		interrupt-names = "pcie_irq";
+		clocks = <&topckgen CLK_TOP_PE2_MAC_P1_SEL>,
 			 <&pericfg CLK_PERI_PCIE1>;
-		clock-names = "sys_ck0", "sys_ck1", "ahb_ck0", "ahb_ck1";
-		phys = <&u3port0 PHY_TYPE_PCIE>, <&u3port1 PHY_TYPE_PCIE>;
-		phy-names = "pcie-phy0", "pcie-phy1";
+		clock-names = "sys_ck1", "ahb_ck1";
+		phys = <&u3port1 PHY_TYPE_PCIE>;
+		phy-names = "pcie-phy1";
 		bus-range = <0x00 0xff>;
-		ranges = <0x82000000 0 0x20000000  0x0 0x20000000  0 0x10000000>;
+		ranges = <0x82000000 0 0x11400000  0x0 0x11400000  0 0x300000>;
+		status = "disabled";
 
-		pcie0: pcie@0,0 {
-			device_type = "pci";
-			status = "disabled";
-			reg = <0x0000 0 0 0 0>;
-			#address-cells = <3>;
-			#size-cells = <2>;
+		#interrupt-cells = <1>;
+		interrupt-map-mask = <0 0 0 7>;
+		interrupt-map = <0 0 0 1 &pcie_intc1 0>,
+				<0 0 0 2 &pcie_intc1 1>,
+				<0 0 0 3 &pcie_intc1 2>,
+				<0 0 0 4 &pcie_intc1 3>;
+		pcie_intc1: interrupt-controller {
+			interrupt-controller;
+			#address-cells = <0>;
 			#interrupt-cells = <1>;
-			ranges;
-			interrupt-map-mask = <0 0 0 7>;
-			interrupt-map = <0 0 0 1 &pcie_intc0 0>,
-					<0 0 0 2 &pcie_intc0 1>,
-					<0 0 0 3 &pcie_intc0 2>,
-					<0 0 0 4 &pcie_intc0 3>;
-			pcie_intc0: interrupt-controller {
-				interrupt-controller;
-				#address-cells = <0>;
-				#interrupt-cells = <1>;
-			};
 		};
+	};
 
-		pcie1: pcie@1,0 {
-			device_type = "pci";
-			status = "disabled";
-			reg = <0x0800 0 0 0 0>;
-			#address-cells = <3>;
-			#size-cells = <2>;
+	pcie0: pcie@11700000 {
+		compatible = "mediatek,mt2712-pcie";
+		device_type = "pci";
+		reg = <0 0x11700000 0 0x1000>;
+		reg-names = "port0";
+		linux,pci-domain = <0>;
+		#address-cells = <3>;
+		#size-cells = <2>;
+		interrupts = <GIC_SPI 115 IRQ_TYPE_LEVEL_HIGH>;
+		interrupt-names = "pcie_irq";
+		clocks = <&topckgen CLK_TOP_PE2_MAC_P0_SEL>,
+			 <&pericfg CLK_PERI_PCIE0>;
+		clock-names = "sys_ck0", "ahb_ck0";
+		phys = <&u3port0 PHY_TYPE_PCIE>;
+		phy-names = "pcie-phy0";
+		bus-range = <0x00 0xff>;
+		ranges = <0x82000000 0 0x20000000 0x0 0x20000000 0 0x10000000>;
+		status = "disabled";
+
+		#interrupt-cells = <1>;
+		interrupt-map-mask = <0 0 0 7>;
+		interrupt-map = <0 0 0 1 &pcie_intc0 0>,
+				<0 0 0 2 &pcie_intc0 1>,
+				<0 0 0 3 &pcie_intc0 2>,
+				<0 0 0 4 &pcie_intc0 3>;
+		pcie_intc0: interrupt-controller {
+			interrupt-controller;
+			#address-cells = <0>;
 			#interrupt-cells = <1>;
-			ranges;
-			interrupt-map-mask = <0 0 0 7>;
-			interrupt-map = <0 0 0 1 &pcie_intc1 0>,
-					<0 0 0 2 &pcie_intc1 1>,
-					<0 0 0 3 &pcie_intc1 2>,
-					<0 0 0 4 &pcie_intc1 3>;
-			pcie_intc1: interrupt-controller {
-				interrupt-controller;
-				#address-cells = <0>;
-				#interrupt-cells = <1>;
-			};
 		};
 	};
 
diff --git a/arch/arm64/boot/dts/mediatek/mt6358.dtsi b/arch/arm64/boot/dts/mediatek/mt6358.dtsi
index fa159b20379e..95145076b7e6 100644
--- a/arch/arm64/boot/dts/mediatek/mt6358.dtsi
+++ b/arch/arm64/boot/dts/mediatek/mt6358.dtsi
@@ -13,6 +13,7 @@
 
 		mt6358codec: mt6358codec {
 			compatible = "mediatek,mt6358-sound";
+			mediatek,dmic-mode = <0>; /* two-wires */
 		};
 
 		mt6358regulator: mt6358regulator {
diff --git a/arch/arm64/boot/dts/mediatek/mt7622-bananapi-bpi-r64.dts b/arch/arm64/boot/dts/mediatek/mt7622-bananapi-bpi-r64.dts
index 2f77dc40b9b8..2b9bf8dd14ec 100644
--- a/arch/arm64/boot/dts/mediatek/mt7622-bananapi-bpi-r64.dts
+++ b/arch/arm64/boot/dts/mediatek/mt7622-bananapi-bpi-r64.dts
@@ -257,18 +257,16 @@
 	};
 };
 
-&pcie {
+&pcie0 {
 	pinctrl-names = "default";
-	pinctrl-0 = <&pcie0_pins>, <&pcie1_pins>;
+	pinctrl-0 = <&pcie0_pins>;
 	status = "okay";
+};
 
-	pcie@0,0 {
-		status = "okay";
-	};
-
-	pcie@1,0 {
-		status = "okay";
-	};
+&pcie1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pcie1_pins>;
+	status = "okay";
 };
 
 &pio {
diff --git a/arch/arm64/boot/dts/mediatek/mt7622-rfb1.dts b/arch/arm64/boot/dts/mediatek/mt7622-rfb1.dts
index f2dc850010f1..596c073d8b05 100644
--- a/arch/arm64/boot/dts/mediatek/mt7622-rfb1.dts
+++ b/arch/arm64/boot/dts/mediatek/mt7622-rfb1.dts
@@ -234,14 +234,10 @@
 	};
 };
 
-&pcie {
+&pcie0 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pcie0_pins>;
 	status = "okay";
-
-	pcie@0,0 {
-		status = "okay";
-	};
 };
 
 &pio {
diff --git a/arch/arm64/boot/dts/mediatek/mt7622.dtsi b/arch/arm64/boot/dts/mediatek/mt7622.dtsi
index 890a942ec608..6f8cb3ad1e84 100644
--- a/arch/arm64/boot/dts/mediatek/mt7622.dtsi
+++ b/arch/arm64/boot/dts/mediatek/mt7622.dtsi
@@ -781,75 +781,83 @@
 		#reset-cells = <1>;
 	};
 
-	pcie: pcie@1a140000 {
+	pciecfg: pciecfg@1a140000 {
+		compatible = "mediatek,generic-pciecfg", "syscon";
+		reg = <0 0x1a140000 0 0x1000>;
+	};
+
+	pcie0: pcie@1a143000 {
 		compatible = "mediatek,mt7622-pcie";
 		device_type = "pci";
-		reg = <0 0x1a140000 0 0x1000>,
-		      <0 0x1a143000 0 0x1000>,
-		      <0 0x1a145000 0 0x1000>;
-		reg-names = "subsys", "port0", "port1";
+		reg = <0 0x1a143000 0 0x1000>;
+		reg-names = "port0";
+		linux,pci-domain = <0>;
 		#address-cells = <3>;
 		#size-cells = <2>;
-		interrupts = <GIC_SPI 228 IRQ_TYPE_LEVEL_LOW>,
-			     <GIC_SPI 229 IRQ_TYPE_LEVEL_LOW>;
+		interrupts = <GIC_SPI 228 IRQ_TYPE_LEVEL_LOW>;
+		interrupt-names = "pcie_irq";
 		clocks = <&pciesys CLK_PCIE_P0_MAC_EN>,
-			 <&pciesys CLK_PCIE_P1_MAC_EN>,
-			 <&pciesys CLK_PCIE_P0_AHB_EN>,
 			 <&pciesys CLK_PCIE_P0_AHB_EN>,
 			 <&pciesys CLK_PCIE_P0_AUX_EN>,
-			 <&pciesys CLK_PCIE_P1_AUX_EN>,
 			 <&pciesys CLK_PCIE_P0_AXI_EN>,
-			 <&pciesys CLK_PCIE_P1_AXI_EN>,
 			 <&pciesys CLK_PCIE_P0_OBFF_EN>,
-			 <&pciesys CLK_PCIE_P1_OBFF_EN>,
-			 <&pciesys CLK_PCIE_P0_PIPE_EN>,
-			 <&pciesys CLK_PCIE_P1_PIPE_EN>;
-		clock-names = "sys_ck0", "sys_ck1", "ahb_ck0", "ahb_ck1",
-			      "aux_ck0", "aux_ck1", "axi_ck0", "axi_ck1",
-			      "obff_ck0", "obff_ck1", "pipe_ck0", "pipe_ck1";
+			 <&pciesys CLK_PCIE_P0_PIPE_EN>;
+		clock-names = "sys_ck0", "ahb_ck0", "aux_ck0",
+			      "axi_ck0", "obff_ck0", "pipe_ck0";
+
 		power-domains = <&scpsys MT7622_POWER_DOMAIN_HIF0>;
 		bus-range = <0x00 0xff>;
-		ranges = <0x82000000 0 0x20000000 0x0 0x20000000 0 0x10000000>;
+		ranges = <0x82000000 0 0x20000000 0x0 0x20000000 0 0x8000000>;
 		status = "disabled";
 
-		pcie0: pcie@0,0 {
-			reg = <0x0000 0 0 0 0>;
-			#address-cells = <3>;
-			#size-cells = <2>;
+		#interrupt-cells = <1>;
+		interrupt-map-mask = <0 0 0 7>;
+		interrupt-map = <0 0 0 1 &pcie_intc0 0>,
+				<0 0 0 2 &pcie_intc0 1>,
+				<0 0 0 3 &pcie_intc0 2>,
+				<0 0 0 4 &pcie_intc0 3>;
+		pcie_intc0: interrupt-controller {
+			interrupt-controller;
+			#address-cells = <0>;
 			#interrupt-cells = <1>;
-			ranges;
-			status = "disabled";
-
-			interrupt-map-mask = <0 0 0 7>;
-			interrupt-map = <0 0 0 1 &pcie_intc0 0>,
-					<0 0 0 2 &pcie_intc0 1>,
-					<0 0 0 3 &pcie_intc0 2>,
-					<0 0 0 4 &pcie_intc0 3>;
-			pcie_intc0: interrupt-controller {
-				interrupt-controller;
-				#address-cells = <0>;
-				#interrupt-cells = <1>;
-			};
 		};
+	};
 
-		pcie1: pcie@1,0 {
-			reg = <0x0800 0 0 0 0>;
-			#address-cells = <3>;
-			#size-cells = <2>;
+	pcie1: pcie@1a145000 {
+		compatible = "mediatek,mt7622-pcie";
+		device_type = "pci";
+		reg = <0 0x1a145000 0 0x1000>;
+		reg-names = "port1";
+		linux,pci-domain = <1>;
+		#address-cells = <3>;
+		#size-cells = <2>;
+		interrupts = <GIC_SPI 229 IRQ_TYPE_LEVEL_LOW>;
+		interrupt-names = "pcie_irq";
+		clocks = <&pciesys CLK_PCIE_P1_MAC_EN>,
+			 /* designer has connect RC1 with p0_ahb clock */
+			 <&pciesys CLK_PCIE_P0_AHB_EN>,
+			 <&pciesys CLK_PCIE_P1_AUX_EN>,
+			 <&pciesys CLK_PCIE_P1_AXI_EN>,
+			 <&pciesys CLK_PCIE_P1_OBFF_EN>,
+			 <&pciesys CLK_PCIE_P1_PIPE_EN>;
+		clock-names = "sys_ck1", "ahb_ck1", "aux_ck1",
+			      "axi_ck1", "obff_ck1", "pipe_ck1";
+
+		power-domains = <&scpsys MT7622_POWER_DOMAIN_HIF0>;
+		bus-range = <0x00 0xff>;
+		ranges = <0x82000000 0 0x28000000 0x0 0x28000000 0 0x8000000>;
+		status = "disabled";
+
+		#interrupt-cells = <1>;
+		interrupt-map-mask = <0 0 0 7>;
+		interrupt-map = <0 0 0 1 &pcie_intc1 0>,
+				<0 0 0 2 &pcie_intc1 1>,
+				<0 0 0 3 &pcie_intc1 2>,
+				<0 0 0 4 &pcie_intc1 3>;
+		pcie_intc1: interrupt-controller {
+			interrupt-controller;
+			#address-cells = <0>;
 			#interrupt-cells = <1>;
-			ranges;
-			status = "disabled";
-
-			interrupt-map-mask = <0 0 0 7>;
-			interrupt-map = <0 0 0 1 &pcie_intc1 0>,
-					<0 0 0 2 &pcie_intc1 1>,
-					<0 0 0 3 &pcie_intc1 2>,
-					<0 0 0 4 &pcie_intc1 3>;
-			pcie_intc1: interrupt-controller {
-				interrupt-controller;
-				#address-cells = <0>;
-				#interrupt-cells = <1>;
-			};
 		};
 	};
 
diff --git a/arch/arm64/boot/dts/mediatek/mt8173.dtsi b/arch/arm64/boot/dts/mediatek/mt8173.dtsi
index d9e005ae5bb0..dee66e5f054c 100644
--- a/arch/arm64/boot/dts/mediatek/mt8173.dtsi
+++ b/arch/arm64/boot/dts/mediatek/mt8173.dtsi
@@ -996,6 +996,7 @@
 			assigned-clocks = <&topckgen CLK_TOP_MM_SEL>;
 			assigned-clock-rates = <400000000>;
 			#clock-cells = <1>;
+			#reset-cells = <1>;
 			mboxes = <&gce 0 CMDQ_THR_PRIO_HIGHEST>,
 				 <&gce 1 CMDQ_THR_PRIO_HIGHEST>;
 			mediatek,gce-client-reg = <&gce SUBSYS_1400XXXX 0 0x1000>;
@@ -1222,6 +1223,7 @@
 				 <&mmsys CLK_MM_DSI0_DIGITAL>,
 				 <&mipi_tx0>;
 			clock-names = "engine", "digital", "hs";
+			resets = <&mmsys MT8173_MMSYS_SW0_RST_B_DISP_DSI0>;
 			phys = <&mipi_tx0>;
 			phy-names = "dphy";
 			status = "disabled";
diff --git a/arch/arm64/boot/dts/mediatek/mt8183-kukui-audio-da7219-max98357a.dtsi b/arch/arm64/boot/dts/mediatek/mt8183-kukui-audio-da7219-max98357a.dtsi
new file mode 100644
index 000000000000..e4aeea4599f5
--- /dev/null
+++ b/arch/arm64/boot/dts/mediatek/mt8183-kukui-audio-da7219-max98357a.dtsi
@@ -0,0 +1,13 @@
+// SPDX-License-Identifier: (GPL-2.0 OR MIT)
+/*
+ * Google Kukui (and derivatives) da7219-max98357a sound card.
+ *
+ * Copyright 2019 Google LLC.
+ */
+
+#include "mt8183-kukui-audio-da7219.dtsi"
+#include "mt8183-kukui-audio-max98357a.dtsi"
+
+&sound {
+	compatible = "mediatek,mt8183_da7219_max98357";
+};
diff --git a/arch/arm64/boot/dts/mediatek/mt8183-kukui-audio-da7219-rt1015p.dtsi b/arch/arm64/boot/dts/mediatek/mt8183-kukui-audio-da7219-rt1015p.dtsi
new file mode 100644
index 000000000000..16ce5a3612ee
--- /dev/null
+++ b/arch/arm64/boot/dts/mediatek/mt8183-kukui-audio-da7219-rt1015p.dtsi
@@ -0,0 +1,13 @@
+// SPDX-License-Identifier: (GPL-2.0 OR MIT)
+/*
+ * Google Kukui (and derivatives) da7219-rt1015p sound card.
+ *
+ * Copyright 2020 Google LLC.
+ */
+
+#include "mt8183-kukui-audio-da7219.dtsi"
+#include "mt8183-kukui-audio-rt1015p.dtsi"
+
+&sound {
+	compatible = "mediatek,mt8183_da7219_rt1015p";
+};
diff --git a/arch/arm64/boot/dts/mediatek/mt8183-kukui-audio-da7219.dtsi b/arch/arm64/boot/dts/mediatek/mt8183-kukui-audio-da7219.dtsi
new file mode 100644
index 000000000000..2c69e7658dba
--- /dev/null
+++ b/arch/arm64/boot/dts/mediatek/mt8183-kukui-audio-da7219.dtsi
@@ -0,0 +1,54 @@
+// SPDX-License-Identifier: (GPL-2.0 OR MIT)
+/*
+ * Google Kukui (and derivatives) audio fragment for da7219.
+ *
+ * Copyright 2020 Google LLC.
+ */
+
+&i2c5 {
+	da7219: da7219@1a {
+		pinctrl-names = "default";
+		pinctrl-0 = <&da7219_pins>;
+		compatible = "dlg,da7219";
+		reg = <0x1a>;
+		interrupt-parent = <&pio>;
+		interrupts = <165 IRQ_TYPE_LEVEL_LOW 165 0>;
+
+		dlg,micbias-lvl = <2600>;
+		dlg,mic-amp-in-sel = "diff";
+		VDD-supply = <&pp1800_alw>;
+		VDDMIC-supply = <&pp3300_alw>;
+		VDDIO-supply = <&pp1800_alw>;
+
+		status = "okay";
+
+		da7219_aad {
+			dlg,adc-1bit-rpt = <1>;
+			dlg,btn-avg = <4>;
+			dlg,btn-cfg = <50>;
+			dlg,mic-det-thr = <500>;
+			dlg,jack-ins-deb = <20>;
+			dlg,jack-det-rate = "32ms_64ms";
+			dlg,jack-rem-deb = <1>;
+
+			dlg,a-d-btn-thr = <0xa>;
+			dlg,d-b-btn-thr = <0x16>;
+			dlg,b-c-btn-thr = <0x21>;
+			dlg,c-mic-btn-thr = <0x3E>;
+		};
+	};
+};
+
+&pio {
+	da7219_pins: da7219_pins {
+		pins1 {
+			pinmux = <PINMUX_GPIO165__FUNC_GPIO165>;
+			input-enable;
+			bias-pull-up;
+		};
+	};
+};
+
+&sound {
+	mediatek,headset-codec = <&da7219>;
+};
diff --git a/arch/arm64/boot/dts/mediatek/mt8183-kukui-audio-max98357a.dtsi b/arch/arm64/boot/dts/mediatek/mt8183-kukui-audio-max98357a.dtsi
new file mode 100644
index 000000000000..2b60967c0c1c
--- /dev/null
+++ b/arch/arm64/boot/dts/mediatek/mt8183-kukui-audio-max98357a.dtsi
@@ -0,0 +1,13 @@
+// SPDX-License-Identifier: (GPL-2.0 OR MIT)
+/*
+ * Google Kukui (and derivatives) audio fragment for max98357a.
+ *
+ * Copyright 2020 Google LLC.
+ */
+
+/ {
+	max98357a: max98357a {
+		compatible = "maxim,max98357a";
+		sdmode-gpios = <&pio 175 0>;
+	};
+};
diff --git a/arch/arm64/boot/dts/mediatek/mt8183-kukui-audio-rt1015p.dtsi b/arch/arm64/boot/dts/mediatek/mt8183-kukui-audio-rt1015p.dtsi
new file mode 100644
index 000000000000..658a764fe9ee
--- /dev/null
+++ b/arch/arm64/boot/dts/mediatek/mt8183-kukui-audio-rt1015p.dtsi
@@ -0,0 +1,13 @@
+// SPDX-License-Identifier: (GPL-2.0 OR MIT)
+/*
+ * Google Kukui (and derivatives) audio fragment for rt1015p.
+ *
+ * Copyright 2020 Google LLC.
+ */
+
+/ {
+	rt1015p: rt1015p {
+		compatible = "realtek,rt1015p";
+		sdb-gpios = <&pio 175 0>;
+	};
+};
diff --git a/arch/arm64/boot/dts/mediatek/mt8183-kukui-audio-ts3a227e-max98357a.dtsi b/arch/arm64/boot/dts/mediatek/mt8183-kukui-audio-ts3a227e-max98357a.dtsi
new file mode 100644
index 000000000000..260a5f561495
--- /dev/null
+++ b/arch/arm64/boot/dts/mediatek/mt8183-kukui-audio-ts3a227e-max98357a.dtsi
@@ -0,0 +1,13 @@
+// SPDX-License-Identifier: (GPL-2.0 OR MIT)
+/*
+ * Google Kukui (and derivatives) ts3a227e-max98357a sound card.
+ *
+ * Copyright 2020 Google LLC.
+ */
+
+#include "mt8183-kukui-audio-max98357a.dtsi"
+#include "mt8183-kukui-audio-ts3a227e.dtsi"
+
+&sound {
+	compatible = "mediatek,mt8183_mt6358_ts3a227_max98357";
+};
diff --git a/arch/arm64/boot/dts/mediatek/mt8183-kukui-audio-ts3a227e-rt1015p.dtsi b/arch/arm64/boot/dts/mediatek/mt8183-kukui-audio-ts3a227e-rt1015p.dtsi
new file mode 100644
index 000000000000..2f7d1fa1c90f
--- /dev/null
+++ b/arch/arm64/boot/dts/mediatek/mt8183-kukui-audio-ts3a227e-rt1015p.dtsi
@@ -0,0 +1,13 @@
+// SPDX-License-Identifier: (GPL-2.0 OR MIT)
+/*
+ * Google Kukui (and derivatives) mt6358-ts3a227-rt1015p sound card.
+ *
+ * Copyright 2021 Google LLC.
+ */
+
+#include "mt8183-kukui-audio-ts3a227e.dtsi"
+#include "mt8183-kukui-audio-rt1015p.dtsi"
+
+&sound {
+	compatible = "mediatek,mt8183_mt6358_ts3a227_rt1015p";
+};
diff --git a/arch/arm64/boot/dts/mediatek/mt8183-kukui-audio-ts3a227e.dtsi b/arch/arm64/boot/dts/mediatek/mt8183-kukui-audio-ts3a227e.dtsi
new file mode 100644
index 000000000000..0799c48ade19
--- /dev/null
+++ b/arch/arm64/boot/dts/mediatek/mt8183-kukui-audio-ts3a227e.dtsi
@@ -0,0 +1,32 @@
+// SPDX-License-Identifier: (GPL-2.0 OR MIT)
+/*
+ * Google Kukui (and derivatives) audio fragment for ts3a227e.
+ *
+ * Copyright 2019 Google LLC.
+ */
+
+&i2c5 {
+	ts3a227e: ts3a227e@3b {
+		pinctrl-names = "default";
+		pinctrl-0 = <&ts3a227e_pins>;
+		compatible = "ti,ts3a227e";
+		reg = <0x3b>;
+		interrupt-parent = <&pio>;
+		interrupts = <157 IRQ_TYPE_LEVEL_LOW>;
+		status = "okay";
+	};
+};
+
+&pio {
+	ts3a227e_pins: ts3a227e_pins {
+		pins1 {
+			pinmux = <PINMUX_GPIO157__FUNC_GPIO157>;
+			input-enable;
+			bias-pull-up;
+		};
+	};
+};
+
+&sound {
+	mediatek,headset-codec = <&ts3a227e>;
+};
diff --git a/arch/arm64/boot/dts/mediatek/mt8183-kukui-jacuzzi-burnet.dts b/arch/arm64/boot/dts/mediatek/mt8183-kukui-jacuzzi-burnet.dts
index a8d6f32ade8d..1a2ec0787d3c 100644
--- a/arch/arm64/boot/dts/mediatek/mt8183-kukui-jacuzzi-burnet.dts
+++ b/arch/arm64/boot/dts/mediatek/mt8183-kukui-jacuzzi-burnet.dts
@@ -5,6 +5,7 @@
 
 /dts-v1/;
 #include "mt8183-kukui-jacuzzi.dtsi"
+#include "mt8183-kukui-audio-ts3a227e-max98357a.dtsi"
 
 / {
 	model = "Google burnet board";
diff --git a/arch/arm64/boot/dts/mediatek/mt8183-kukui-jacuzzi-damu.dts b/arch/arm64/boot/dts/mediatek/mt8183-kukui-jacuzzi-damu.dts
index 42ba9c00866c..0eca3ff8672a 100644
--- a/arch/arm64/boot/dts/mediatek/mt8183-kukui-jacuzzi-damu.dts
+++ b/arch/arm64/boot/dts/mediatek/mt8183-kukui-jacuzzi-damu.dts
@@ -5,6 +5,7 @@
 
 /dts-v1/;
 #include "mt8183-kukui-jacuzzi.dtsi"
+#include "mt8183-kukui-audio-da7219-max98357a.dtsi"
 
 / {
 	model = "Google damu board";
diff --git a/arch/arm64/boot/dts/mediatek/mt8183-kukui-jacuzzi-fennel.dtsi b/arch/arm64/boot/dts/mediatek/mt8183-kukui-jacuzzi-fennel.dtsi
index bbe6c338f465..577519a775c0 100644
--- a/arch/arm64/boot/dts/mediatek/mt8183-kukui-jacuzzi-fennel.dtsi
+++ b/arch/arm64/boot/dts/mediatek/mt8183-kukui-jacuzzi-fennel.dtsi
@@ -5,6 +5,7 @@
 
 /dts-v1/;
 #include "mt8183-kukui-jacuzzi.dtsi"
+#include "mt8183-kukui-audio-da7219-rt1015p.dtsi"
 
 &mt6358codec {
 	mediatek,dmic-mode = <1>; /* one-wire */
diff --git a/arch/arm64/boot/dts/mediatek/mt8183-kukui-jacuzzi-juniper-sku16.dts b/arch/arm64/boot/dts/mediatek/mt8183-kukui-jacuzzi-juniper-sku16.dts
index 36d2c3b3cadf..bc2c57f0a827 100644
--- a/arch/arm64/boot/dts/mediatek/mt8183-kukui-jacuzzi-juniper-sku16.dts
+++ b/arch/arm64/boot/dts/mediatek/mt8183-kukui-jacuzzi-juniper-sku16.dts
@@ -5,6 +5,7 @@
 
 /dts-v1/;
 #include "mt8183-kukui-jacuzzi-juniper.dtsi"
+#include "mt8183-kukui-audio-ts3a227e-max98357a.dtsi"
 
 / {
 	model = "Google juniper sku16 board";
diff --git a/arch/arm64/boot/dts/mediatek/mt8183-kukui-jacuzzi-kappa.dts b/arch/arm64/boot/dts/mediatek/mt8183-kukui-jacuzzi-kappa.dts
index b3f46c16e5d7..e5bd9191e426 100644
--- a/arch/arm64/boot/dts/mediatek/mt8183-kukui-jacuzzi-kappa.dts
+++ b/arch/arm64/boot/dts/mediatek/mt8183-kukui-jacuzzi-kappa.dts
@@ -5,6 +5,7 @@
 
 /dts-v1/;
 #include "mt8183-kukui-jacuzzi.dtsi"
+#include "mt8183-kukui-audio-ts3a227e-max98357a.dtsi"
 
 / {
 	model = "Google kappa board";
diff --git a/arch/arm64/boot/dts/mediatek/mt8183-kukui-jacuzzi-kenzo.dts b/arch/arm64/boot/dts/mediatek/mt8183-kukui-jacuzzi-kenzo.dts
index 6f1aa692753a..8fa89db03e63 100644
--- a/arch/arm64/boot/dts/mediatek/mt8183-kukui-jacuzzi-kenzo.dts
+++ b/arch/arm64/boot/dts/mediatek/mt8183-kukui-jacuzzi-kenzo.dts
@@ -5,6 +5,7 @@
 
 /dts-v1/;
 #include "mt8183-kukui-jacuzzi-juniper.dtsi"
+#include "mt8183-kukui-audio-ts3a227e-max98357a.dtsi"
 
 / {
 	model = "Google kenzo sku17 board";
diff --git a/arch/arm64/boot/dts/mediatek/mt8183-kukui-jacuzzi-willow-sku0.dts b/arch/arm64/boot/dts/mediatek/mt8183-kukui-jacuzzi-willow-sku0.dts
index 281265f082db..89208b843b27 100644
--- a/arch/arm64/boot/dts/mediatek/mt8183-kukui-jacuzzi-willow-sku0.dts
+++ b/arch/arm64/boot/dts/mediatek/mt8183-kukui-jacuzzi-willow-sku0.dts
@@ -5,6 +5,7 @@
 
 /dts-v1/;
 #include "mt8183-kukui-jacuzzi-willow.dtsi"
+#include "mt8183-kukui-audio-da7219-max98357a.dtsi"
 
 / {
 	model = "Google willow board sku0";
diff --git a/arch/arm64/boot/dts/mediatek/mt8183-kukui-jacuzzi-willow-sku1.dts b/arch/arm64/boot/dts/mediatek/mt8183-kukui-jacuzzi-willow-sku1.dts
index 22e56bdc1ee3..c7b20441d053 100644
--- a/arch/arm64/boot/dts/mediatek/mt8183-kukui-jacuzzi-willow-sku1.dts
+++ b/arch/arm64/boot/dts/mediatek/mt8183-kukui-jacuzzi-willow-sku1.dts
@@ -5,6 +5,7 @@
 
 /dts-v1/;
 #include "mt8183-kukui-jacuzzi-willow.dtsi"
+#include "mt8183-kukui-audio-ts3a227e-max98357a.dtsi"
 
 / {
 	model = "Google willow board sku1";
diff --git a/arch/arm64/boot/dts/mediatek/mt8183-kukui-kakadu.dts b/arch/arm64/boot/dts/mediatek/mt8183-kukui-kakadu.dts
index 20eb0dc68f09..89a139a0ee44 100644
--- a/arch/arm64/boot/dts/mediatek/mt8183-kukui-kakadu.dts
+++ b/arch/arm64/boot/dts/mediatek/mt8183-kukui-kakadu.dts
@@ -5,6 +5,7 @@
 
 /dts-v1/;
 #include "mt8183-kukui-kakadu.dtsi"
+#include "mt8183-kukui-audio-da7219-rt1015p.dtsi"
 
 / {
 	model = "MediaTek kakadu board";
diff --git a/arch/arm64/boot/dts/mediatek/mt8183-kukui-kodama.dtsi b/arch/arm64/boot/dts/mediatek/mt8183-kukui-kodama.dtsi
index 3aa79403c0c2..06f8c80bf553 100644
--- a/arch/arm64/boot/dts/mediatek/mt8183-kukui-kodama.dtsi
+++ b/arch/arm64/boot/dts/mediatek/mt8183-kukui-kodama.dtsi
@@ -5,6 +5,7 @@
 
 /dts-v1/;
 #include "mt8183-kukui.dtsi"
+#include "mt8183-kukui-audio-ts3a227e-max98357a.dtsi"
 
 / {
 	ppvarn_lcd: ppvarn-lcd {
diff --git a/arch/arm64/boot/dts/mediatek/mt8183-kukui-krane.dtsi b/arch/arm64/boot/dts/mediatek/mt8183-kukui-krane.dtsi
index 30c183c96a54..a7b0cb3ff7b0 100644
--- a/arch/arm64/boot/dts/mediatek/mt8183-kukui-krane.dtsi
+++ b/arch/arm64/boot/dts/mediatek/mt8183-kukui-krane.dtsi
@@ -4,6 +4,7 @@
  */
 
 #include "mt8183-kukui.dtsi"
+#include "mt8183-kukui-audio-max98357a.dtsi"
 
 / {
 	ppvarn_lcd: ppvarn-lcd {
@@ -345,3 +346,7 @@
 &qca_wifi {
 	qcom,ath10k-calibration-variant = "LE_Krane";
 };
+
+&sound {
+	compatible = "mediatek,mt8183_mt6358_ts3a227_max98357";
+};
diff --git a/arch/arm64/boot/dts/mediatek/mt8183-kukui.dtsi b/arch/arm64/boot/dts/mediatek/mt8183-kukui.dtsi
index 8e9cf36a9a41..b42d81d26d72 100644
--- a/arch/arm64/boot/dts/mediatek/mt8183-kukui.dtsi
+++ b/arch/arm64/boot/dts/mediatek/mt8183-kukui.dtsi
@@ -115,12 +115,18 @@
 		};
 	};
 
-	max98357a: codec0 {
-		compatible = "maxim,max98357a";
-		sdmode-gpios = <&pio 175 0>;
+	sound: mt8183-sound {
+		mediatek,platform = <&afe>;
+		pinctrl-names = "default",
+				"aud_tdm_out_on",
+				"aud_tdm_out_off";
+		pinctrl-0 = <&aud_pins_default>;
+		pinctrl-1 = <&aud_pins_tdm_out_on>;
+		pinctrl-2 = <&aud_pins_tdm_out_off>;
+		status = "okay";
 	};
 
-	btsco: codec1 {
+	btsco: bt-sco {
 		compatible = "linux,bt-sco";
 	};
 
@@ -215,6 +221,11 @@
 	};
 };
 
+&afe {
+	i2s3-share = "I2S2";
+	i2s0-share = "I2S5";
+};
+
 &auxadc {
 	status = "okay";
 };
@@ -402,6 +413,54 @@
 };
 
 &pio {
+	aud_pins_default: audiopins {
+		pins_bus {
+			pinmux = <PINMUX_GPIO97__FUNC_I2S2_MCK>,
+				<PINMUX_GPIO98__FUNC_I2S2_BCK>,
+				<PINMUX_GPIO101__FUNC_I2S2_LRCK>,
+				<PINMUX_GPIO102__FUNC_I2S2_DI>,
+				<PINMUX_GPIO3__FUNC_I2S3_DO>, /*i2s to da7219/max98357*/
+				<PINMUX_GPIO89__FUNC_I2S5_BCK>,
+				<PINMUX_GPIO90__FUNC_I2S5_LRCK>,
+				<PINMUX_GPIO91__FUNC_I2S5_DO>,
+				<PINMUX_GPIO174__FUNC_I2S0_DI>, /*i2s to wifi/bt*/
+				<PINMUX_GPIO136__FUNC_AUD_CLK_MOSI>,
+				<PINMUX_GPIO137__FUNC_AUD_SYNC_MOSI>,
+				<PINMUX_GPIO138__FUNC_AUD_DAT_MOSI0>,
+				<PINMUX_GPIO139__FUNC_AUD_DAT_MOSI1>,
+				<PINMUX_GPIO140__FUNC_AUD_CLK_MISO>,
+				<PINMUX_GPIO141__FUNC_AUD_SYNC_MISO>,
+				<PINMUX_GPIO142__FUNC_AUD_DAT_MISO0>,
+				<PINMUX_GPIO143__FUNC_AUD_DAT_MISO1>; /*mtkaif3.0*/
+		};
+	};
+
+	aud_pins_tdm_out_on: audiotdmouton {
+		pins_bus {
+			pinmux = <PINMUX_GPIO169__FUNC_TDM_BCK_2ND>,
+				<PINMUX_GPIO170__FUNC_TDM_LRCK_2ND>,
+				<PINMUX_GPIO171__FUNC_TDM_DATA0_2ND>,
+				<PINMUX_GPIO172__FUNC_TDM_DATA1_2ND>,
+				<PINMUX_GPIO173__FUNC_TDM_DATA2_2ND>,
+				<PINMUX_GPIO10__FUNC_TDM_DATA3>; /*8ch-i2s to it6505*/
+			drive-strength = <MTK_DRIVE_6mA>;
+		};
+	};
+
+	aud_pins_tdm_out_off: audiotdmoutoff {
+		pins_bus {
+			pinmux = <PINMUX_GPIO169__FUNC_GPIO169>,
+				<PINMUX_GPIO170__FUNC_GPIO170>,
+				<PINMUX_GPIO171__FUNC_GPIO171>,
+				<PINMUX_GPIO172__FUNC_GPIO172>,
+				<PINMUX_GPIO173__FUNC_GPIO173>,
+				<PINMUX_GPIO10__FUNC_GPIO10>;
+			input-enable;
+			bias-pull-down;
+			drive-strength = <MTK_DRIVE_2mA>;
+		};
+	};
+
 	bt_pins: bt-pins {
 		pins_bt_en {
 			pinmux = <PINMUX_GPIO120__FUNC_GPIO120>;
diff --git a/arch/arm64/boot/dts/mediatek/mt8183.dtsi b/arch/arm64/boot/dts/mediatek/mt8183.dtsi
index 409cf827970c..ba4584faca5a 100644
--- a/arch/arm64/boot/dts/mediatek/mt8183.dtsi
+++ b/arch/arm64/boot/dts/mediatek/mt8183.dtsi
@@ -11,7 +11,7 @@
 #include <dt-bindings/interrupt-controller/irq.h>
 #include <dt-bindings/memory/mt8183-larb-port.h>
 #include <dt-bindings/power/mt8183-power.h>
-#include <dt-bindings/reset-controller/mt8183-resets.h>
+#include <dt-bindings/reset/mt8183-resets.h>
 #include <dt-bindings/phy/phy.h>
 #include <dt-bindings/thermal/thermal.h>
 #include <dt-bindings/pinctrl/mt8183-pinfunc.h>
@@ -1115,10 +1115,102 @@
 			};
 		};
 
-		audiosys: syscon@11220000 {
+		audiosys: audio-controller@11220000 {
 			compatible = "mediatek,mt8183-audiosys", "syscon";
 			reg = <0 0x11220000 0 0x1000>;
 			#clock-cells = <1>;
+			afe: mt8183-afe-pcm {
+				compatible = "mediatek,mt8183-audio";
+				interrupts = <GIC_SPI 161 IRQ_TYPE_LEVEL_LOW>;
+				resets = <&watchdog MT8183_TOPRGU_AUDIO_SW_RST>;
+				reset-names = "audiosys";
+				power-domains =
+					<&spm MT8183_POWER_DOMAIN_AUDIO>;
+				clocks = <&audiosys CLK_AUDIO_AFE>,
+					 <&audiosys CLK_AUDIO_DAC>,
+					 <&audiosys CLK_AUDIO_DAC_PREDIS>,
+					 <&audiosys CLK_AUDIO_ADC>,
+					 <&audiosys CLK_AUDIO_PDN_ADDA6_ADC>,
+					 <&audiosys CLK_AUDIO_22M>,
+					 <&audiosys CLK_AUDIO_24M>,
+					 <&audiosys CLK_AUDIO_APLL_TUNER>,
+					 <&audiosys CLK_AUDIO_APLL2_TUNER>,
+					 <&audiosys CLK_AUDIO_I2S1>,
+					 <&audiosys CLK_AUDIO_I2S2>,
+					 <&audiosys CLK_AUDIO_I2S3>,
+					 <&audiosys CLK_AUDIO_I2S4>,
+					 <&audiosys CLK_AUDIO_TDM>,
+					 <&audiosys CLK_AUDIO_TML>,
+					 <&infracfg CLK_INFRA_AUDIO>,
+					 <&infracfg CLK_INFRA_AUDIO_26M_BCLK>,
+					 <&topckgen CLK_TOP_MUX_AUDIO>,
+					 <&topckgen CLK_TOP_MUX_AUD_INTBUS>,
+					 <&topckgen CLK_TOP_SYSPLL_D2_D4>,
+					 <&topckgen CLK_TOP_MUX_AUD_1>,
+					 <&topckgen CLK_TOP_APLL1_CK>,
+					 <&topckgen CLK_TOP_MUX_AUD_2>,
+					 <&topckgen CLK_TOP_APLL2_CK>,
+					 <&topckgen CLK_TOP_MUX_AUD_ENG1>,
+					 <&topckgen CLK_TOP_APLL1_D8>,
+					 <&topckgen CLK_TOP_MUX_AUD_ENG2>,
+					 <&topckgen CLK_TOP_APLL2_D8>,
+					 <&topckgen CLK_TOP_MUX_APLL_I2S0>,
+					 <&topckgen CLK_TOP_MUX_APLL_I2S1>,
+					 <&topckgen CLK_TOP_MUX_APLL_I2S2>,
+					 <&topckgen CLK_TOP_MUX_APLL_I2S3>,
+					 <&topckgen CLK_TOP_MUX_APLL_I2S4>,
+					 <&topckgen CLK_TOP_MUX_APLL_I2S5>,
+					 <&topckgen CLK_TOP_APLL12_DIV0>,
+					 <&topckgen CLK_TOP_APLL12_DIV1>,
+					 <&topckgen CLK_TOP_APLL12_DIV2>,
+					 <&topckgen CLK_TOP_APLL12_DIV3>,
+					 <&topckgen CLK_TOP_APLL12_DIV4>,
+					 <&topckgen CLK_TOP_APLL12_DIVB>,
+					 /*<&topckgen CLK_TOP_APLL12_DIV5>,*/
+					 <&clk26m>;
+				clock-names = "aud_afe_clk",
+						  "aud_dac_clk",
+						  "aud_dac_predis_clk",
+						  "aud_adc_clk",
+						  "aud_adc_adda6_clk",
+						  "aud_apll22m_clk",
+						  "aud_apll24m_clk",
+						  "aud_apll1_tuner_clk",
+						  "aud_apll2_tuner_clk",
+						  "aud_i2s1_bclk_sw",
+						  "aud_i2s2_bclk_sw",
+						  "aud_i2s3_bclk_sw",
+						  "aud_i2s4_bclk_sw",
+						  "aud_tdm_clk",
+						  "aud_tml_clk",
+						  "aud_infra_clk",
+						  "mtkaif_26m_clk",
+						  "top_mux_audio",
+						  "top_mux_aud_intbus",
+						  "top_syspll_d2_d4",
+						  "top_mux_aud_1",
+						  "top_apll1_ck",
+						  "top_mux_aud_2",
+						  "top_apll2_ck",
+						  "top_mux_aud_eng1",
+						  "top_apll1_d8",
+						  "top_mux_aud_eng2",
+						  "top_apll2_d8",
+						  "top_i2s0_m_sel",
+						  "top_i2s1_m_sel",
+						  "top_i2s2_m_sel",
+						  "top_i2s3_m_sel",
+						  "top_i2s4_m_sel",
+						  "top_i2s5_m_sel",
+						  "top_apll12_div0",
+						  "top_apll12_div1",
+						  "top_apll12_div2",
+						  "top_apll12_div3",
+						  "top_apll12_div4",
+						  "top_apll12_divb",
+						  /*"top_apll12_div5",*/
+						  "top_clk26m_clk";
+			};
 		};
 
 		mmc0: mmc@11230000 {
@@ -1227,6 +1319,7 @@
 			compatible = "mediatek,mt8183-mmsys", "syscon";
 			reg = <0 0x14000000 0 0x1000>;
 			#clock-cells = <1>;
+			#reset-cells = <1>;
 			mboxes = <&gce 0 CMDQ_THR_PRIO_HIGHEST>,
 				 <&gce 1 CMDQ_THR_PRIO_HIGHEST>;
 			mediatek,gce-client-reg = <&gce SUBSYS_1400XXXX 0 0x1000>;
@@ -1341,11 +1434,11 @@
 			reg = <0 0x14014000 0 0x1000>;
 			interrupts = <GIC_SPI 236 IRQ_TYPE_LEVEL_LOW>;
 			power-domains = <&spm MT8183_POWER_DOMAIN_DISP>;
-			mediatek,syscon-dsi = <&mmsys 0x140>;
 			clocks = <&mmsys CLK_MM_DSI0_MM>,
 				 <&mmsys CLK_MM_DSI0_IF>,
 				 <&mipi_tx0>;
 			clock-names = "engine", "digital", "hs";
+			resets = <&mmsys MT8183_MMSYS_SW0_RST_B_DISP_DSI0>;
 			phys = <&mipi_tx0>;
 			phy-names = "dphy";
 		};
diff --git a/arch/arm64/boot/dts/mediatek/mt8192.dtsi b/arch/arm64/boot/dts/mediatek/mt8192.dtsi
index 9757138a8bbd..c7c7d4e017ae 100644
--- a/arch/arm64/boot/dts/mediatek/mt8192.dtsi
+++ b/arch/arm64/boot/dts/mediatek/mt8192.dtsi
@@ -5,6 +5,7 @@
  */
 
 /dts-v1/;
+#include <dt-bindings/clock/mt8192-clk.h>
 #include <dt-bindings/interrupt-controller/arm-gic.h>
 #include <dt-bindings/interrupt-controller/irq.h>
 #include <dt-bindings/pinctrl/mt8192-pinfunc.h>
@@ -257,6 +258,24 @@
 			};
 		};
 
+		topckgen: syscon@10000000 {
+			compatible = "mediatek,mt8192-topckgen", "syscon";
+			reg = <0 0x10000000 0 0x1000>;
+			#clock-cells = <1>;
+		};
+
+		infracfg: syscon@10001000 {
+			compatible = "mediatek,mt8192-infracfg", "syscon";
+			reg = <0 0x10001000 0 0x1000>;
+			#clock-cells = <1>;
+		};
+
+		pericfg: syscon@10003000 {
+			compatible = "mediatek,mt8192-pericfg", "syscon";
+			reg = <0 0x10003000 0 0x1000>;
+			#clock-cells = <1>;
+		};
+
 		pio: pinctrl@10005000 {
 			compatible = "mediatek,mt8192-pinctrl";
 			reg = <0 0x10005000 0 0x1000>,
@@ -282,6 +301,12 @@
 			#interrupt-cells = <2>;
 		};
 
+		apmixedsys: syscon@1000c000 {
+			compatible = "mediatek,mt8192-apmixedsys", "syscon";
+			reg = <0 0x1000c000 0 0x1000>;
+			#clock-cells = <1>;
+		};
+
 		systimer: timer@10017000 {
 			compatible = "mediatek,mt8192-timer",
 				     "mediatek,mt6765-timer";
@@ -291,6 +316,12 @@
 			clock-names = "clk13m";
 		};
 
+		scp_adsp: clock-controller@10720000 {
+			compatible = "mediatek,mt8192-scp_adsp";
+			reg = <0 0x10720000 0 0x1000>;
+			#clock-cells = <1>;
+		};
+
 		uart0: serial@11002000 {
 			compatible = "mediatek,mt8192-uart",
 				     "mediatek,mt6577-uart";
@@ -311,6 +342,12 @@
 			status = "disabled";
 		};
 
+		imp_iic_wrap_c: clock-controller@11007000 {
+			compatible = "mediatek,mt8192-imp_iic_wrap_c";
+			reg = <0 0x11007000 0 0x1000>;
+			#clock-cells = <1>;
+		};
+
 		spi0: spi@1100a000 {
 			compatible = "mediatek,mt8192-spi",
 				     "mediatek,mt6765-spi";
@@ -436,6 +473,12 @@
 			status = "disable";
 		};
 
+		audsys: clock-controller@11210000 {
+			compatible = "mediatek,mt8192-audsys", "syscon";
+			reg = <0 0x11210000 0 0x1000>;
+			#clock-cells = <1>;
+		};
+
 		i2c3: i2c3@11cb0000 {
 			compatible = "mediatek,mt8192-i2c";
 			reg = <0 0x11cb0000 0 0x1000>,
@@ -449,6 +492,12 @@
 			status = "disabled";
 		};
 
+		imp_iic_wrap_e: clock-controller@11cb1000 {
+			compatible = "mediatek,mt8192-imp_iic_wrap_e";
+			reg = <0 0x11cb1000 0 0x1000>;
+			#clock-cells = <1>;
+		};
+
 		i2c7: i2c7@11d00000 {
 			compatible = "mediatek,mt8192-i2c";
 			reg = <0 0x11d00000 0 0x1000>,
@@ -488,6 +537,12 @@
 			status = "disabled";
 		};
 
+		imp_iic_wrap_s: clock-controller@11d03000 {
+			compatible = "mediatek,mt8192-imp_iic_wrap_s";
+			reg = <0 0x11d03000 0 0x1000>;
+			#clock-cells = <1>;
+		};
+
 		i2c1: i2c1@11d20000 {
 			compatible = "mediatek,mt8192-i2c";
 			reg = <0 0x11d20000 0 0x1000>,
@@ -527,6 +582,12 @@
 			status = "disabled";
 		};
 
+		imp_iic_wrap_ws: clock-controller@11d23000 {
+			compatible = "mediatek,mt8192-imp_iic_wrap_ws";
+			reg = <0 0x11d23000 0 0x1000>;
+			#clock-cells = <1>;
+		};
+
 		i2c5: i2c5@11e00000 {
 			compatible = "mediatek,mt8192-i2c";
 			reg = <0 0x11e00000 0 0x1000>,
@@ -540,6 +601,12 @@
 			status = "disabled";
 		};
 
+		imp_iic_wrap_w: clock-controller@11e01000 {
+			compatible = "mediatek,mt8192-imp_iic_wrap_w";
+			reg = <0 0x11e01000 0 0x1000>;
+			#clock-cells = <1>;
+		};
+
 		i2c0: i2c0@11f00000 {
 			compatible = "mediatek,mt8192-i2c";
 			reg = <0 0x11f00000 0 0x1000>,
@@ -565,5 +632,101 @@
 			#size-cells = <0>;
 			status = "disabled";
 		};
+
+		imp_iic_wrap_n: clock-controller@11f02000 {
+			compatible = "mediatek,mt8192-imp_iic_wrap_n";
+			reg = <0 0x11f02000 0 0x1000>;
+			#clock-cells = <1>;
+		};
+
+		msdc_top: clock-controller@11f10000 {
+			compatible = "mediatek,mt8192-msdc_top";
+			reg = <0 0x11f10000 0 0x1000>;
+			#clock-cells = <1>;
+		};
+
+		msdc: clock-controller@11f60000 {
+			compatible = "mediatek,mt8192-msdc";
+			reg = <0 0x11f60000 0 0x1000>;
+			#clock-cells = <1>;
+		};
+
+		mfgcfg: clock-controller@13fbf000 {
+			compatible = "mediatek,mt8192-mfgcfg";
+			reg = <0 0x13fbf000 0 0x1000>;
+			#clock-cells = <1>;
+		};
+
+		mmsys: syscon@14000000 {
+			compatible = "mediatek,mt8192-mmsys", "syscon";
+			reg = <0 0x14000000 0 0x1000>;
+			#clock-cells = <1>;
+		};
+
+		imgsys: clock-controller@15020000 {
+			compatible = "mediatek,mt8192-imgsys";
+			reg = <0 0x15020000 0 0x1000>;
+			#clock-cells = <1>;
+		};
+
+		imgsys2: clock-controller@15820000 {
+			compatible = "mediatek,mt8192-imgsys2";
+			reg = <0 0x15820000 0 0x1000>;
+			#clock-cells = <1>;
+		};
+
+		vdecsys_soc: clock-controller@1600f000 {
+			compatible = "mediatek,mt8192-vdecsys_soc";
+			reg = <0 0x1600f000 0 0x1000>;
+			#clock-cells = <1>;
+		};
+
+		vdecsys: clock-controller@1602f000 {
+			compatible = "mediatek,mt8192-vdecsys";
+			reg = <0 0x1602f000 0 0x1000>;
+			#clock-cells = <1>;
+		};
+
+		vencsys: clock-controller@17000000 {
+			compatible = "mediatek,mt8192-vencsys";
+			reg = <0 0x17000000 0 0x1000>;
+			#clock-cells = <1>;
+		};
+
+		camsys: clock-controller@1a000000 {
+			compatible = "mediatek,mt8192-camsys";
+			reg = <0 0x1a000000 0 0x1000>;
+			#clock-cells = <1>;
+		};
+
+		camsys_rawa: clock-controller@1a04f000 {
+			compatible = "mediatek,mt8192-camsys_rawa";
+			reg = <0 0x1a04f000 0 0x1000>;
+			#clock-cells = <1>;
+		};
+
+		camsys_rawb: clock-controller@1a06f000 {
+			compatible = "mediatek,mt8192-camsys_rawb";
+			reg = <0 0x1a06f000 0 0x1000>;
+			#clock-cells = <1>;
+		};
+
+		camsys_rawc: clock-controller@1a08f000 {
+			compatible = "mediatek,mt8192-camsys_rawc";
+			reg = <0 0x1a08f000 0 0x1000>;
+			#clock-cells = <1>;
+		};
+
+		ipesys: clock-controller@1b000000 {
+			compatible = "mediatek,mt8192-ipesys";
+			reg = <0 0x1b000000 0 0x1000>;
+			#clock-cells = <1>;
+		};
+
+		mdpsys: clock-controller@1f000000 {
+			compatible = "mediatek,mt8192-mdpsys";
+			reg = <0 0x1f000000 0 0x1000>;
+			#clock-cells = <1>;
+		};
 	};
 };
diff --git a/arch/arm64/boot/dts/nvidia/tegra132-norrin.dts b/arch/arm64/boot/dts/nvidia/tegra132-norrin.dts
index 6e5f8465669e..8a51751526ee 100644
--- a/arch/arm64/boot/dts/nvidia/tegra132-norrin.dts
+++ b/arch/arm64/boot/dts/nvidia/tegra132-norrin.dts
@@ -1021,8 +1021,6 @@
 
 		brightness-levels = <0 4 8 16 32 64 128 255>;
 		default-brightness-level = <6>;
-
-		backlight-boot-off;
 	};
 
 	clk32k_in: clock@0 {
diff --git a/arch/arm64/boot/dts/nvidia/tegra132.dtsi b/arch/arm64/boot/dts/nvidia/tegra132.dtsi
index b0bcda8cc51f..63aa3129d8fc 100644
--- a/arch/arm64/boot/dts/nvidia/tegra132.dtsi
+++ b/arch/arm64/boot/dts/nvidia/tegra132.dtsi
@@ -1107,7 +1107,7 @@
 	};
 
 	usb@7d000000 {
-		compatible = "nvidia,tegra124-ehci", "nvidia,tegra30-ehci", "usb-ehci";
+		compatible = "nvidia,tegra124-ehci", "nvidia,tegra30-ehci";
 		reg = <0x0 0x7d000000 0x0 0x4000>;
 		interrupts = <GIC_SPI 20 IRQ_TYPE_LEVEL_HIGH>;
 		phy_type = "utmi";
@@ -1123,6 +1123,7 @@
 		compatible = "nvidia,tegra124-usb-phy", "nvidia,tegra30-usb-phy";
 		reg = <0x0 0x7d000000 0x0 0x4000>,
 		      <0x0 0x7d000000 0x0 0x4000>;
+		interrupts = <GIC_SPI 20 IRQ_TYPE_LEVEL_HIGH>;
 		phy_type = "utmi";
 		clocks = <&tegra_car TEGRA124_CLK_USBD>,
 			 <&tegra_car TEGRA124_CLK_PLL_U>,
@@ -1142,11 +1143,12 @@
 		nvidia,hsdiscon-level = <5>;
 		nvidia,xcvr-hsslew = <12>;
 		nvidia,has-utmi-pad-registers;
+		nvidia,pmc = <&tegra_pmc 0>;
 		status = "disabled";
 	};
 
 	usb@7d004000 {
-		compatible = "nvidia,tegra124-ehci", "nvidia,tegra30-ehci", "usb-ehci";
+		compatible = "nvidia,tegra124-ehci", "nvidia,tegra30-ehci";
 		reg = <0x0 0x7d004000 0x0 0x4000>;
 		interrupts = <GIC_SPI 21 IRQ_TYPE_LEVEL_HIGH>;
 		phy_type = "utmi";
@@ -1162,6 +1164,7 @@
 		compatible = "nvidia,tegra124-usb-phy", "nvidia,tegra30-usb-phy";
 		reg = <0x0 0x7d004000 0x0 0x4000>,
 		      <0x0 0x7d000000 0x0 0x4000>;
+		interrupts = <GIC_SPI 21 IRQ_TYPE_LEVEL_HIGH>;
 		phy_type = "utmi";
 		clocks = <&tegra_car TEGRA124_CLK_USB2>,
 			 <&tegra_car TEGRA124_CLK_PLL_U>,
@@ -1180,11 +1183,12 @@
 		nvidia,hssquelch-level = <2>;
 		nvidia,hsdiscon-level = <5>;
 		nvidia,xcvr-hsslew = <12>;
+		nvidia,pmc = <&tegra_pmc 1>;
 		status = "disabled";
 	};
 
 	usb@7d008000 {
-		compatible = "nvidia,tegra124-ehci", "nvidia,tegra30-ehci", "usb-ehci";
+		compatible = "nvidia,tegra124-ehci", "nvidia,tegra30-ehci";
 		reg = <0x0 0x7d008000 0x0 0x4000>;
 		interrupts = <GIC_SPI 97 IRQ_TYPE_LEVEL_HIGH>;
 		phy_type = "utmi";
@@ -1200,6 +1204,7 @@
 		compatible = "nvidia,tegra124-usb-phy", "nvidia,tegra30-usb-phy";
 		reg = <0x0 0x7d008000 0x0 0x4000>,
 		      <0x0 0x7d000000 0x0 0x4000>;
+		interrupts = <GIC_SPI 97 IRQ_TYPE_LEVEL_HIGH>;
 		phy_type = "utmi";
 		clocks = <&tegra_car TEGRA124_CLK_USB3>,
 			 <&tegra_car TEGRA124_CLK_PLL_U>,
@@ -1218,6 +1223,7 @@
 		nvidia,hssquelch-level = <2>;
 		nvidia,hsdiscon-level = <5>;
 		nvidia,xcvr-hsslew = <12>;
+		nvidia,pmc = <&tegra_pmc 2>;
 		status = "disabled";
 	};
 
diff --git a/arch/arm64/boot/dts/nvidia/tegra186-p2771-0000.dts b/arch/arm64/boot/dts/nvidia/tegra186-p2771-0000.dts
index 74c1a5df3fdb..52fa258533e6 100644
--- a/arch/arm64/boot/dts/nvidia/tegra186-p2771-0000.dts
+++ b/arch/arm64/boot/dts/nvidia/tegra186-p2771-0000.dts
@@ -275,6 +275,542 @@
 						remote-endpoint = <&dspk2_cif_ep>;
 					};
 				};
+
+				xbar_sfc1_in_port: port@20 {
+					reg = <0x20>;
+
+					xbar_sfc1_in_ep: endpoint {
+						remote-endpoint = <&sfc1_cif_in_ep>;
+					};
+				};
+
+				port@21 {
+					reg = <0x21>;
+
+					xbar_sfc1_out_ep: endpoint {
+						remote-endpoint = <&sfc1_cif_out_ep>;
+					};
+				};
+
+				xbar_sfc2_in_port: port@22 {
+					reg = <0x22>;
+
+					xbar_sfc2_in_ep: endpoint {
+						remote-endpoint = <&sfc2_cif_in_ep>;
+					};
+				};
+
+				port@23 {
+					reg = <0x23>;
+
+					xbar_sfc2_out_ep: endpoint {
+						remote-endpoint = <&sfc2_cif_out_ep>;
+					};
+				};
+
+				xbar_sfc3_in_port: port@24 {
+					reg = <0x24>;
+
+					xbar_sfc3_in_ep: endpoint {
+						remote-endpoint = <&sfc3_cif_in_ep>;
+					};
+				};
+
+				port@25 {
+					reg = <0x25>;
+
+					xbar_sfc3_out_ep: endpoint {
+						remote-endpoint = <&sfc3_cif_out_ep>;
+					};
+				};
+
+				xbar_sfc4_in_port: port@26 {
+					reg = <0x26>;
+
+					xbar_sfc4_in_ep: endpoint {
+						remote-endpoint = <&sfc4_cif_in_ep>;
+					};
+				};
+
+				port@27 {
+					reg = <0x27>;
+
+					xbar_sfc4_out_ep: endpoint {
+						remote-endpoint = <&sfc4_cif_out_ep>;
+					};
+				};
+
+				xbar_mvc1_in_port: port@28 {
+					reg = <0x28>;
+
+					xbar_mvc1_in_ep: endpoint {
+						remote-endpoint = <&mvc1_cif_in_ep>;
+					};
+				};
+
+				port@29 {
+					reg = <0x29>;
+
+					xbar_mvc1_out_ep: endpoint {
+						remote-endpoint = <&mvc1_cif_out_ep>;
+					};
+				};
+
+				xbar_mvc2_in_port: port@2a {
+					reg = <0x2a>;
+
+					xbar_mvc2_in_ep: endpoint {
+						remote-endpoint = <&mvc2_cif_in_ep>;
+					};
+				};
+
+				port@2b {
+					reg = <0x2b>;
+
+					xbar_mvc2_out_ep: endpoint {
+						remote-endpoint = <&mvc2_cif_out_ep>;
+					};
+				};
+
+				xbar_amx1_in1_port: port@2c {
+					reg = <0x2c>;
+
+					xbar_amx1_in1_ep: endpoint {
+						remote-endpoint = <&amx1_in1_ep>;
+					};
+				};
+
+				xbar_amx1_in2_port: port@2d {
+					reg = <0x2d>;
+
+					xbar_amx1_in2_ep: endpoint {
+						remote-endpoint = <&amx1_in2_ep>;
+					};
+				};
+
+				xbar_amx1_in3_port: port@2e {
+					reg = <0x2e>;
+
+					xbar_amx1_in3_ep: endpoint {
+						remote-endpoint = <&amx1_in3_ep>;
+					};
+				};
+
+				xbar_amx1_in4_port: port@2f {
+					reg = <0x2f>;
+
+					xbar_amx1_in4_ep: endpoint {
+						remote-endpoint = <&amx1_in4_ep>;
+					};
+				};
+
+				port@30 {
+					reg = <0x30>;
+
+					xbar_amx1_out_ep: endpoint {
+						remote-endpoint = <&amx1_out_ep>;
+					};
+				};
+
+				xbar_amx2_in1_port: port@31 {
+					reg = <0x31>;
+
+					xbar_amx2_in1_ep: endpoint {
+						remote-endpoint = <&amx2_in1_ep>;
+					};
+				};
+
+				xbar_amx2_in2_port: port@32 {
+					reg = <0x32>;
+
+					xbar_amx2_in2_ep: endpoint {
+						remote-endpoint = <&amx2_in2_ep>;
+					};
+				};
+
+				xbar_amx2_in3_port: port@33 {
+					reg = <0x33>;
+
+					xbar_amx2_in3_ep: endpoint {
+						remote-endpoint = <&amx2_in3_ep>;
+					};
+				};
+
+				xbar_amx2_in4_port: port@34 {
+					reg = <0x34>;
+
+					xbar_amx2_in4_ep: endpoint {
+						remote-endpoint = <&amx2_in4_ep>;
+					};
+				};
+
+				port@35 {
+					reg = <0x35>;
+
+					xbar_amx2_out_ep: endpoint {
+						remote-endpoint = <&amx2_out_ep>;
+					};
+				};
+
+				xbar_amx3_in1_port: port@36 {
+					reg = <0x36>;
+
+					xbar_amx3_in1_ep: endpoint {
+						remote-endpoint = <&amx3_in1_ep>;
+					};
+				};
+
+				xbar_amx3_in2_port: port@37 {
+					reg = <0x37>;
+
+					xbar_amx3_in2_ep: endpoint {
+						remote-endpoint = <&amx3_in2_ep>;
+					};
+				};
+
+				xbar_amx3_in3_port: port@38 {
+					reg = <0x38>;
+
+					xbar_amx3_in3_ep: endpoint {
+						remote-endpoint = <&amx3_in3_ep>;
+					};
+				};
+
+				xbar_amx3_in4_port: port@39 {
+					reg = <0x39>;
+
+					xbar_amx3_in4_ep: endpoint {
+						remote-endpoint = <&amx3_in4_ep>;
+					};
+				};
+
+				port@3a {
+					reg = <0x3a>;
+
+					xbar_amx3_out_ep: endpoint {
+						remote-endpoint = <&amx3_out_ep>;
+					};
+				};
+
+				xbar_amx4_in1_port: port@3b {
+					reg = <0x3b>;
+
+					xbar_amx4_in1_ep: endpoint {
+						remote-endpoint = <&amx4_in1_ep>;
+					};
+				};
+
+				xbar_amx4_in2_port: port@3c {
+					reg = <0x3c>;
+
+					xbar_amx4_in2_ep: endpoint {
+						remote-endpoint = <&amx4_in2_ep>;
+					};
+				};
+
+				xbar_amx4_in3_port: port@3d {
+					reg = <0x3d>;
+
+					xbar_amx4_in3_ep: endpoint {
+						remote-endpoint = <&amx4_in3_ep>;
+					};
+				};
+
+				xbar_amx4_in4_port: port@3e {
+					reg = <0x3e>;
+
+					xbar_amx4_in4_ep: endpoint {
+						remote-endpoint = <&amx4_in4_ep>;
+					};
+				};
+
+				port@3f {
+					reg = <0x3f>;
+
+					xbar_amx4_out_ep: endpoint {
+						remote-endpoint = <&amx4_out_ep>;
+					};
+				};
+
+				xbar_adx1_in_port: port@40 {
+					reg = <0x40>;
+
+					xbar_adx1_in_ep: endpoint {
+						remote-endpoint = <&adx1_in_ep>;
+					};
+				};
+
+				port@41 {
+					reg = <0x41>;
+
+					xbar_adx1_out1_ep: endpoint {
+						remote-endpoint = <&adx1_out1_ep>;
+					};
+				};
+
+				port@42 {
+					reg = <0x42>;
+
+					xbar_adx1_out2_ep: endpoint {
+						remote-endpoint = <&adx1_out2_ep>;
+					};
+				};
+
+				port@43 {
+					reg = <0x43>;
+
+					xbar_adx1_out3_ep: endpoint {
+						remote-endpoint = <&adx1_out3_ep>;
+					};
+				};
+
+				port@44 {
+					reg = <0x44>;
+
+					xbar_adx1_out4_ep: endpoint {
+						remote-endpoint = <&adx1_out4_ep>;
+					};
+				};
+
+				xbar_adx2_in_port: port@45 {
+					reg = <0x45>;
+
+					xbar_adx2_in_ep: endpoint {
+						remote-endpoint = <&adx2_in_ep>;
+					};
+				};
+
+				port@46 {
+					reg = <0x46>;
+
+					xbar_adx2_out1_ep: endpoint {
+						remote-endpoint = <&adx2_out1_ep>;
+					};
+				};
+
+				port@47 {
+					reg = <0x47>;
+
+					xbar_adx2_out2_ep: endpoint {
+						remote-endpoint = <&adx2_out2_ep>;
+					};
+				};
+
+				port@48 {
+					reg = <0x48>;
+
+					xbar_adx2_out3_ep: endpoint {
+						remote-endpoint = <&adx2_out3_ep>;
+					};
+				};
+
+				port@49 {
+					reg = <0x49>;
+
+					xbar_adx2_out4_ep: endpoint {
+						remote-endpoint = <&adx2_out4_ep>;
+					};
+				};
+
+				xbar_adx3_in_port: port@4a {
+					reg = <0x4a>;
+
+					xbar_adx3_in_ep: endpoint {
+						remote-endpoint = <&adx3_in_ep>;
+					};
+				};
+
+				port@4b {
+					reg = <0x4b>;
+
+					xbar_adx3_out1_ep: endpoint {
+						remote-endpoint = <&adx3_out1_ep>;
+					};
+				};
+
+				port@4c {
+					reg = <0x4c>;
+
+					xbar_adx3_out2_ep: endpoint {
+						remote-endpoint = <&adx3_out2_ep>;
+					};
+				};
+
+				port@4d {
+					reg = <0x4d>;
+
+					xbar_adx3_out3_ep: endpoint {
+						remote-endpoint = <&adx3_out3_ep>;
+					};
+				};
+
+				port@4e {
+					reg = <0x4e>;
+
+					xbar_adx3_out4_ep: endpoint {
+						remote-endpoint = <&adx3_out4_ep>;
+					};
+				};
+
+				xbar_adx4_in_port: port@4f {
+					reg = <0x4f>;
+
+					xbar_adx4_in_ep: endpoint {
+						remote-endpoint = <&adx4_in_ep>;
+					};
+				};
+
+				port@50 {
+					reg = <0x50>;
+
+					xbar_adx4_out1_ep: endpoint {
+						remote-endpoint = <&adx4_out1_ep>;
+					};
+				};
+
+				port@51 {
+					reg = <0x51>;
+
+					xbar_adx4_out2_ep: endpoint {
+						remote-endpoint = <&adx4_out2_ep>;
+					};
+				};
+
+				port@52 {
+					reg = <0x52>;
+
+					xbar_adx4_out3_ep: endpoint {
+						remote-endpoint = <&adx4_out3_ep>;
+					};
+				};
+
+				port@53 {
+					reg = <0x53>;
+
+					xbar_adx4_out4_ep: endpoint {
+						remote-endpoint = <&adx4_out4_ep>;
+					};
+				};
+
+				xbar_mixer_in1_port: port@54 {
+					reg = <0x54>;
+
+					xbar_mixer_in1_ep: endpoint {
+						remote-endpoint = <&mixer_in1_ep>;
+					};
+				};
+
+				xbar_mixer_in2_port: port@55 {
+					reg = <0x55>;
+
+					xbar_mixer_in2_ep: endpoint {
+						remote-endpoint = <&mixer_in2_ep>;
+					};
+				};
+
+				xbar_mixer_in3_port: port@56 {
+					reg = <0x56>;
+
+					xbar_mixer_in3_ep: endpoint {
+						remote-endpoint = <&mixer_in3_ep>;
+					};
+				};
+
+				xbar_mixer_in4_port: port@57 {
+					reg = <0x57>;
+
+					xbar_mixer_in4_ep: endpoint {
+						remote-endpoint = <&mixer_in4_ep>;
+					};
+				};
+
+				xbar_mixer_in5_port: port@58 {
+					reg = <0x58>;
+
+					xbar_mixer_in5_ep: endpoint {
+						remote-endpoint = <&mixer_in5_ep>;
+					};
+				};
+
+				xbar_mixer_in6_port: port@59 {
+					reg = <0x59>;
+
+					xbar_mixer_in6_ep: endpoint {
+						remote-endpoint = <&mixer_in6_ep>;
+					};
+				};
+
+				xbar_mixer_in7_port: port@5a {
+					reg = <0x5a>;
+
+					xbar_mixer_in7_ep: endpoint {
+						remote-endpoint = <&mixer_in7_ep>;
+					};
+				};
+
+				xbar_mixer_in8_port: port@5b {
+					reg = <0x5b>;
+
+					xbar_mixer_in8_ep: endpoint {
+						remote-endpoint = <&mixer_in8_ep>;
+					};
+				};
+
+				xbar_mixer_in9_port: port@5c {
+					reg = <0x5c>;
+
+					xbar_mixer_in9_ep: endpoint {
+						remote-endpoint = <&mixer_in9_ep>;
+					};
+				};
+
+				xbar_mixer_in10_port: port@5d {
+					reg = <0x5d>;
+
+					xbar_mixer_in10_ep: endpoint {
+						remote-endpoint = <&mixer_in10_ep>;
+					};
+				};
+
+				port@5e {
+					reg = <0x5e>;
+
+					xbar_mixer_out1_ep: endpoint {
+						remote-endpoint = <&mixer_out1_ep>;
+					};
+				};
+
+				port@5f {
+					reg = <0x5f>;
+
+					xbar_mixer_out2_ep: endpoint {
+						remote-endpoint = <&mixer_out2_ep>;
+					};
+				};
+
+				port@60 {
+					reg = <0x60>;
+
+					xbar_mixer_out3_ep: endpoint {
+						remote-endpoint = <&mixer_out3_ep>;
+					};
+				};
+
+				port@61 {
+					reg = <0x61>;
+
+					xbar_mixer_out4_ep: endpoint {
+						remote-endpoint = <&mixer_out4_ep>;
+					};
+				};
+
+				port@62 {
+					reg = <0x62>;
+
+					xbar_mixer_out5_ep: endpoint {
+						remote-endpoint = <&mixer_out5_ep>;
+					};
+				};
 			};
 
 			admaif@290f000 {
@@ -726,6 +1262,679 @@
 					};
 				};
 			};
+
+			sfc@2902000 {
+				status = "okay";
+
+				ports {
+					#address-cells = <1>;
+					#size-cells = <0>;
+
+					port@0 {
+						reg = <0>;
+
+						sfc1_cif_in_ep: endpoint {
+							remote-endpoint = <&xbar_sfc1_in_ep>;
+							convert-rate = <44100>;
+						};
+					};
+
+					sfc1_out_port: port@1 {
+						reg = <1>;
+
+						sfc1_cif_out_ep: endpoint {
+							remote-endpoint = <&xbar_sfc1_out_ep>;
+							convert-rate = <48000>;
+						};
+					};
+				};
+			};
+
+			sfc@2902200 {
+				status = "okay";
+
+				ports {
+					#address-cells = <1>;
+					#size-cells = <0>;
+
+					port@0 {
+						reg = <0>;
+
+						sfc2_cif_in_ep: endpoint {
+							remote-endpoint = <&xbar_sfc2_in_ep>;
+						};
+					};
+
+					sfc2_out_port: port@1 {
+						reg = <1>;
+
+						sfc2_cif_out_ep: endpoint {
+							remote-endpoint = <&xbar_sfc2_out_ep>;
+						};
+					};
+				};
+			};
+
+			sfc@2902400 {
+				status = "okay";
+
+				ports {
+					#address-cells = <1>;
+					#size-cells = <0>;
+
+					port@0 {
+						reg = <0>;
+
+						sfc3_cif_in_ep: endpoint {
+							remote-endpoint = <&xbar_sfc3_in_ep>;
+						};
+					};
+
+					sfc3_out_port: port@1 {
+						reg = <1>;
+
+						sfc3_cif_out_ep: endpoint {
+							remote-endpoint = <&xbar_sfc3_out_ep>;
+						};
+					};
+				};
+			};
+
+			sfc@2902600 {
+				status = "okay";
+
+				ports {
+					#address-cells = <1>;
+					#size-cells = <0>;
+
+					port@0 {
+						reg = <0>;
+
+						sfc4_cif_in_ep: endpoint {
+							remote-endpoint = <&xbar_sfc4_in_ep>;
+						};
+					};
+
+					sfc4_out_port: port@1 {
+						reg = <1>;
+
+						sfc4_cif_out_ep: endpoint {
+							remote-endpoint = <&xbar_sfc4_out_ep>;
+						};
+					};
+				};
+			};
+
+			mvc@290a000 {
+				status = "okay";
+
+				ports {
+					#address-cells = <1>;
+					#size-cells = <0>;
+
+					port@0 {
+						reg = <0>;
+
+						mvc1_cif_in_ep: endpoint {
+							remote-endpoint = <&xbar_mvc1_in_ep>;
+						};
+					};
+
+					mvc1_out_port: port@1 {
+						reg = <1>;
+
+						mvc1_cif_out_ep: endpoint {
+							remote-endpoint = <&xbar_mvc1_out_ep>;
+						};
+					};
+				};
+			};
+
+			mvc@290a200 {
+				status = "okay";
+
+				ports {
+					#address-cells = <1>;
+					#size-cells = <0>;
+
+					port@0 {
+						reg = <0>;
+
+						mvc2_cif_in_ep: endpoint {
+							remote-endpoint = <&xbar_mvc2_in_ep>;
+						};
+					};
+
+					mvc2_out_port: port@1 {
+						reg = <1>;
+
+						mvc2_cif_out_ep: endpoint {
+							remote-endpoint = <&xbar_mvc2_out_ep>;
+						};
+					};
+				};
+			};
+
+			amx@2903000 {
+				status = "okay";
+
+				ports {
+					#address-cells = <1>;
+					#size-cells = <0>;
+
+					port@0 {
+						reg = <0>;
+
+						amx1_in1_ep: endpoint {
+							remote-endpoint = <&xbar_amx1_in1_ep>;
+						};
+					};
+
+					port@1 {
+						reg = <1>;
+
+						amx1_in2_ep: endpoint {
+							remote-endpoint = <&xbar_amx1_in2_ep>;
+						};
+					};
+
+					port@2 {
+						reg = <2>;
+
+						amx1_in3_ep: endpoint {
+							remote-endpoint = <&xbar_amx1_in3_ep>;
+						};
+					};
+
+					port@3 {
+						reg = <3>;
+
+						amx1_in4_ep: endpoint {
+							remote-endpoint = <&xbar_amx1_in4_ep>;
+						};
+					};
+
+					amx1_out_port: port@4 {
+						reg = <4>;
+
+						amx1_out_ep: endpoint {
+							remote-endpoint = <&xbar_amx1_out_ep>;
+						};
+					};
+				};
+			};
+
+			amx@2903100 {
+				status = "okay";
+
+				ports {
+					#address-cells = <1>;
+					#size-cells = <0>;
+
+					port@0 {
+						reg = <0>;
+
+						amx2_in1_ep: endpoint {
+							remote-endpoint = <&xbar_amx2_in1_ep>;
+						};
+					};
+
+					port@1 {
+						reg = <1>;
+
+						amx2_in2_ep: endpoint {
+							remote-endpoint = <&xbar_amx2_in2_ep>;
+						};
+					};
+
+					amx2_in3_port: port@2 {
+						reg = <2>;
+
+						amx2_in3_ep: endpoint {
+							remote-endpoint = <&xbar_amx2_in3_ep>;
+						};
+					};
+
+					amx2_in4_port: port@3 {
+						reg = <3>;
+
+						amx2_in4_ep: endpoint {
+							remote-endpoint = <&xbar_amx2_in4_ep>;
+						};
+					};
+
+					amx2_out_port: port@4 {
+						reg = <4>;
+
+						amx2_out_ep: endpoint {
+							remote-endpoint = <&xbar_amx2_out_ep>;
+						};
+					};
+				};
+			};
+
+			amx@2903200 {
+				status = "okay";
+
+				ports {
+					#address-cells = <1>;
+					#size-cells = <0>;
+
+					port@0 {
+						reg = <0>;
+
+						amx3_in1_ep: endpoint {
+							remote-endpoint = <&xbar_amx3_in1_ep>;
+						};
+					};
+
+					port@1 {
+						reg = <1>;
+
+						amx3_in2_ep: endpoint {
+							remote-endpoint = <&xbar_amx3_in2_ep>;
+						};
+					};
+
+					port@2 {
+						reg = <2>;
+
+						amx3_in3_ep: endpoint {
+							remote-endpoint = <&xbar_amx3_in3_ep>;
+						};
+					};
+
+					port@3 {
+						reg = <3>;
+
+						amx3_in4_ep: endpoint {
+							remote-endpoint = <&xbar_amx3_in4_ep>;
+						};
+					};
+
+					amx3_out_port: port@4 {
+						reg = <4>;
+
+						amx3_out_ep: endpoint {
+							remote-endpoint = <&xbar_amx3_out_ep>;
+						};
+					};
+				};
+			};
+
+			amx@2903300 {
+				status = "okay";
+
+				ports {
+					#address-cells = <1>;
+					#size-cells = <0>;
+
+					port@0 {
+						reg = <0>;
+
+						amx4_in1_ep: endpoint {
+							remote-endpoint = <&xbar_amx4_in1_ep>;
+						};
+					};
+
+					port@1 {
+						reg = <1>;
+
+						amx4_in2_ep: endpoint {
+							remote-endpoint = <&xbar_amx4_in2_ep>;
+						};
+					};
+
+					port@2 {
+						reg = <2>;
+
+						amx4_in3_ep: endpoint {
+							remote-endpoint = <&xbar_amx4_in3_ep>;
+						};
+					};
+
+					port@3 {
+						reg = <3>;
+
+						amx4_in4_ep: endpoint {
+							remote-endpoint = <&xbar_amx4_in4_ep>;
+						};
+					};
+
+					amx4_out_port: port@4 {
+						reg = <4>;
+
+						amx4_out_ep: endpoint {
+							remote-endpoint = <&xbar_amx4_out_ep>;
+						};
+					};
+				};
+			};
+
+			adx@2903800 {
+				status = "okay";
+
+				ports {
+					#address-cells = <1>;
+					#size-cells = <0>;
+
+					port@0 {
+						reg = <0>;
+
+						adx1_in_ep: endpoint {
+							remote-endpoint = <&xbar_adx1_in_ep>;
+						};
+					};
+
+					adx1_out1_port: port@1 {
+						reg = <1>;
+
+						adx1_out1_ep: endpoint {
+							remote-endpoint = <&xbar_adx1_out1_ep>;
+						};
+					};
+
+					adx1_out2_port: port@2 {
+						reg = <2>;
+
+						adx1_out2_ep: endpoint {
+							remote-endpoint = <&xbar_adx1_out2_ep>;
+						};
+					};
+
+					adx1_out3_port: port@3 {
+						reg = <3>;
+
+						adx1_out3_ep: endpoint {
+							remote-endpoint = <&xbar_adx1_out3_ep>;
+						};
+					};
+
+					adx1_out4_port: port@4 {
+						reg = <4>;
+
+						adx1_out4_ep: endpoint {
+							remote-endpoint = <&xbar_adx1_out4_ep>;
+						};
+					};
+				};
+			};
+
+			adx@2903900 {
+				status = "okay";
+
+				ports {
+					#address-cells = <1>;
+					#size-cells = <0>;
+
+					port@0 {
+						reg = <0>;
+
+						adx2_in_ep: endpoint {
+							remote-endpoint = <&xbar_adx2_in_ep>;
+						};
+					};
+
+					adx2_out1_port: port@1 {
+						reg = <1>;
+
+						adx2_out1_ep: endpoint {
+							remote-endpoint = <&xbar_adx2_out1_ep>;
+						};
+					};
+
+					adx2_out2_port: port@2 {
+						reg = <2>;
+
+						adx2_out2_ep: endpoint {
+							remote-endpoint = <&xbar_adx2_out2_ep>;
+						};
+					};
+
+					adx2_out3_port: port@3 {
+						reg = <3>;
+
+						adx2_out3_ep: endpoint {
+							remote-endpoint = <&xbar_adx2_out3_ep>;
+						};
+					};
+
+					adx2_out4_port: port@4 {
+						reg = <4>;
+
+						adx2_out4_ep: endpoint {
+							remote-endpoint = <&xbar_adx2_out4_ep>;
+						};
+					};
+				};
+			};
+
+			adx@2903a00 {
+				status = "okay";
+
+				ports {
+					#address-cells = <1>;
+					#size-cells = <0>;
+
+					port@0 {
+						reg = <0>;
+
+						adx3_in_ep: endpoint {
+							remote-endpoint = <&xbar_adx3_in_ep>;
+						};
+					};
+
+					adx3_out1_port: port@1 {
+						reg = <1>;
+
+						adx3_out1_ep: endpoint {
+							remote-endpoint = <&xbar_adx3_out1_ep>;
+						};
+					};
+
+					adx3_out2_port: port@2 {
+						reg = <2>;
+
+						adx3_out2_ep: endpoint {
+							remote-endpoint = <&xbar_adx3_out2_ep>;
+						};
+					};
+
+					adx3_out3_port: port@3 {
+						reg = <3>;
+
+						adx3_out3_ep: endpoint {
+							remote-endpoint = <&xbar_adx3_out3_ep>;
+						};
+					};
+
+					adx3_out4_port: port@4 {
+						reg = <4>;
+
+						adx3_out4_ep: endpoint {
+							remote-endpoint = <&xbar_adx3_out4_ep>;
+						};
+					};
+				};
+			};
+
+			adx@2903b00 {
+				status = "okay";
+
+				ports {
+					#address-cells = <1>;
+					#size-cells = <0>;
+
+					port@0 {
+						reg = <0>;
+
+						adx4_in_ep: endpoint {
+							remote-endpoint = <&xbar_adx4_in_ep>;
+						};
+					};
+
+					adx4_out1_port: port@1 {
+						reg = <1>;
+
+						adx4_out1_ep: endpoint {
+							remote-endpoint = <&xbar_adx4_out1_ep>;
+						};
+					};
+
+					adx4_out2_port: port@2 {
+						reg = <2>;
+
+						adx4_out2_ep: endpoint {
+							remote-endpoint = <&xbar_adx4_out2_ep>;
+						};
+					};
+
+					adx4_out3_port: port@3 {
+						reg = <3>;
+
+						adx4_out3_ep: endpoint {
+							remote-endpoint = <&xbar_adx4_out3_ep>;
+						};
+					};
+
+					adx4_out4_port: port@4 {
+						reg = <4>;
+
+						adx4_out4_ep: endpoint {
+							remote-endpoint = <&xbar_adx4_out4_ep>;
+						};
+					};
+				};
+			};
+
+			amixer@290bb00 {
+				status = "okay";
+
+				ports {
+					#address-cells = <1>;
+					#size-cells = <0>;
+
+					port@0 {
+						reg = <0x0>;
+
+						mixer_in1_ep: endpoint {
+							remote-endpoint = <&xbar_mixer_in1_ep>;
+						};
+					};
+
+					port@1 {
+						reg = <0x1>;
+
+						mixer_in2_ep: endpoint {
+							remote-endpoint = <&xbar_mixer_in2_ep>;
+						};
+					};
+
+					port@2 {
+						reg = <0x2>;
+
+						mixer_in3_ep: endpoint {
+							remote-endpoint = <&xbar_mixer_in3_ep>;
+						};
+					};
+
+					port@3 {
+						reg = <0x3>;
+
+						mixer_in4_ep: endpoint {
+							remote-endpoint = <&xbar_mixer_in4_ep>;
+						};
+					};
+
+					port@4 {
+						reg = <0x4>;
+
+						mixer_in5_ep: endpoint {
+							remote-endpoint = <&xbar_mixer_in5_ep>;
+						};
+					};
+
+					port@5 {
+						reg = <0x5>;
+
+						mixer_in6_ep: endpoint {
+							remote-endpoint = <&xbar_mixer_in6_ep>;
+						};
+					};
+
+					port@6 {
+						reg = <0x6>;
+
+						mixer_in7_ep: endpoint {
+							remote-endpoint = <&xbar_mixer_in7_ep>;
+						};
+					};
+
+					port@7 {
+						reg = <0x7>;
+
+						mixer_in8_ep: endpoint {
+							remote-endpoint = <&xbar_mixer_in8_ep>;
+						};
+					};
+
+					port@8 {
+						reg = <0x8>;
+
+						mixer_in9_ep: endpoint {
+							remote-endpoint = <&xbar_mixer_in9_ep>;
+						};
+					};
+
+					port@9 {
+						reg = <0x9>;
+
+						mixer_in10_ep: endpoint {
+							remote-endpoint = <&xbar_mixer_in10_ep>;
+						};
+					};
+
+					mixer_out1_port: port@a {
+						reg = <0xa>;
+
+						mixer_out1_ep: endpoint {
+							remote-endpoint = <&xbar_mixer_out1_ep>;
+						};
+					};
+
+					mixer_out2_port: port@b {
+						reg = <0xb>;
+
+						mixer_out2_ep: endpoint {
+							remote-endpoint = <&xbar_mixer_out2_ep>;
+						};
+					};
+
+					mixer_out3_port: port@c {
+						reg = <0xc>;
+
+						mixer_out3_ep: endpoint {
+							remote-endpoint = <&xbar_mixer_out3_ep>;
+						};
+					};
+
+					mixer_out4_port: port@d {
+						reg = <0xd>;
+
+						mixer_out4_ep: endpoint {
+							remote-endpoint = <&xbar_mixer_out4_ep>;
+						};
+					};
+
+					mixer_out5_port: port@e {
+						reg = <0xe>;
+
+						mixer_out5_ep: endpoint {
+							remote-endpoint = <&xbar_mixer_out5_ep>;
+						};
+					};
+				};
+			};
 		};
 	};
 
@@ -1104,6 +2313,41 @@
 		       <&xbar_i2s4_port>, <&xbar_i2s5_port>, <&xbar_i2s6_port>,
 		       <&xbar_dmic1_port>, <&xbar_dmic2_port>, <&xbar_dmic3_port>,
 		       <&xbar_dspk1_port>, <&xbar_dspk2_port>,
+		       <&xbar_sfc1_in_port>, <&xbar_sfc2_in_port>,
+		       <&xbar_sfc3_in_port>, <&xbar_sfc4_in_port>,
+		       <&xbar_mvc1_in_port>, <&xbar_mvc2_in_port>,
+		       <&xbar_amx1_in1_port>, <&xbar_amx1_in2_port>,
+		       <&xbar_amx1_in3_port>, <&xbar_amx1_in4_port>,
+		       <&xbar_amx2_in1_port>, <&xbar_amx2_in2_port>,
+		       <&xbar_amx2_in3_port>, <&xbar_amx2_in4_port>,
+		       <&xbar_amx3_in1_port>, <&xbar_amx3_in2_port>,
+		       <&xbar_amx3_in3_port>, <&xbar_amx3_in4_port>,
+		       <&xbar_amx4_in1_port>, <&xbar_amx4_in2_port>,
+		       <&xbar_amx4_in3_port>, <&xbar_amx4_in4_port>,
+		       <&xbar_adx1_in_port>, <&xbar_adx2_in_port>,
+		       <&xbar_adx3_in_port>, <&xbar_adx4_in_port>,
+		       <&xbar_mixer_in1_port>, <&xbar_mixer_in2_port>,
+		       <&xbar_mixer_in3_port>, <&xbar_mixer_in4_port>,
+		       <&xbar_mixer_in5_port>, <&xbar_mixer_in6_port>,
+		       <&xbar_mixer_in7_port>, <&xbar_mixer_in8_port>,
+		       <&xbar_mixer_in9_port>, <&xbar_mixer_in10_port>,
+		       /* HW accelerators */
+		       <&sfc1_out_port>, <&sfc2_out_port>,
+		       <&sfc3_out_port>, <&sfc4_out_port>,
+		       <&mvc1_out_port>, <&mvc2_out_port>,
+		       <&amx1_out_port>, <&amx2_out_port>,
+		       <&amx3_out_port>, <&amx4_out_port>,
+		       <&adx1_out1_port>, <&adx1_out2_port>,
+		       <&adx1_out3_port>, <&adx1_out4_port>,
+		       <&adx2_out1_port>, <&adx2_out2_port>,
+		       <&adx2_out3_port>, <&adx2_out4_port>,
+		       <&adx3_out1_port>, <&adx3_out2_port>,
+		       <&adx3_out3_port>, <&adx3_out4_port>,
+		       <&adx4_out1_port>, <&adx4_out2_port>,
+		       <&adx4_out3_port>, <&adx4_out4_port>,
+		       <&mixer_out1_port>, <&mixer_out2_port>,
+		       <&mixer_out3_port>, <&mixer_out4_port>,
+		       <&mixer_out5_port>,
 		       /* I/O */
 		       <&i2s1_port>, <&i2s2_port>, <&i2s3_port>, <&i2s4_port>,
 		       <&i2s5_port>, <&i2s6_port>, <&dmic1_port>, <&dmic2_port>,
diff --git a/arch/arm64/boot/dts/nvidia/tegra186-p3509-0000+p3636-0001.dts b/arch/arm64/boot/dts/nvidia/tegra186-p3509-0000+p3636-0001.dts
index 936b106e73db..af33fe93e1d6 100644
--- a/arch/arm64/boot/dts/nvidia/tegra186-p3509-0000+p3636-0001.dts
+++ b/arch/arm64/boot/dts/nvidia/tegra186-p3509-0000+p3636-0001.dts
@@ -124,7 +124,7 @@
 	};
 
 	hda@3510000 {
-		nvidia,model = "jetson-tx2-hda";
+		nvidia,model = "NVIDIA Jetson TX2 NX HDA";
 		status = "okay";
 	};
 
@@ -715,4 +715,508 @@
 			};
 		};
 	};
+
+	aconnect@2900000 {
+		status = "okay";
+
+		dma-controller@2930000 {
+			status = "okay";
+		};
+
+		interrupt-controller@2a40000 {
+			status = "okay";
+		};
+
+		ahub@2900800 {
+			status = "okay";
+
+			ports {
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				port@0 {
+					reg = <0x0>;
+
+					xbar_admaif0_ep: endpoint {
+						remote-endpoint = <&admaif0_ep>;
+					};
+				};
+
+				port@1 {
+					reg = <0x1>;
+
+					xbar_admaif1_ep: endpoint {
+						remote-endpoint = <&admaif1_ep>;
+					};
+				};
+
+				port@2 {
+					reg = <0x2>;
+
+					xbar_admaif2_ep: endpoint {
+						remote-endpoint = <&admaif2_ep>;
+					};
+				};
+
+				port@3 {
+					reg = <0x3>;
+
+					xbar_admaif3_ep: endpoint {
+						remote-endpoint = <&admaif3_ep>;
+					};
+				};
+
+				port@4 {
+					reg = <0x4>;
+
+					xbar_admaif4_ep: endpoint {
+						remote-endpoint = <&admaif4_ep>;
+					};
+				};
+
+				port@5 {
+					reg = <0x5>;
+
+					xbar_admaif5_ep: endpoint {
+						remote-endpoint = <&admaif5_ep>;
+					};
+				};
+
+				port@6 {
+					reg = <0x6>;
+
+					xbar_admaif6_ep: endpoint {
+						remote-endpoint = <&admaif6_ep>;
+					};
+				};
+
+				port@7 {
+					reg = <0x7>;
+
+					xbar_admaif7_ep: endpoint {
+						remote-endpoint = <&admaif7_ep>;
+					};
+				};
+
+				port@8 {
+					reg = <0x8>;
+
+					xbar_admaif8_ep: endpoint {
+						remote-endpoint = <&admaif8_ep>;
+					};
+				};
+
+				port@9 {
+					reg = <0x9>;
+
+					xbar_admaif9_ep: endpoint {
+						remote-endpoint = <&admaif9_ep>;
+					};
+				};
+
+				port@a {
+					reg = <0xa>;
+
+					xbar_admaif10_ep: endpoint {
+						remote-endpoint = <&admaif10_ep>;
+					};
+				};
+
+				port@b {
+					reg = <0xb>;
+
+					xbar_admaif11_ep: endpoint {
+						remote-endpoint = <&admaif11_ep>;
+					};
+				};
+
+				port@c {
+					reg = <0xc>;
+
+					xbar_admaif12_ep: endpoint {
+						remote-endpoint = <&admaif12_ep>;
+					};
+				};
+
+				port@d {
+					reg = <0xd>;
+
+					xbar_admaif13_ep: endpoint {
+						remote-endpoint = <&admaif13_ep>;
+					};
+				};
+
+				port@e {
+					reg = <0xe>;
+
+					xbar_admaif14_ep: endpoint {
+						remote-endpoint = <&admaif14_ep>;
+					};
+				};
+
+				port@f {
+					reg = <0xf>;
+
+					xbar_admaif15_ep: endpoint {
+						remote-endpoint = <&admaif15_ep>;
+					};
+				};
+
+				port@10 {
+					reg = <0x10>;
+
+					xbar_admaif16_ep: endpoint {
+						remote-endpoint = <&admaif16_ep>;
+					};
+				};
+
+				port@11 {
+					reg = <0x11>;
+
+					xbar_admaif17_ep: endpoint {
+						remote-endpoint = <&admaif17_ep>;
+					};
+				};
+
+				port@12 {
+					reg = <0x12>;
+
+					xbar_admaif18_ep: endpoint {
+						remote-endpoint = <&admaif18_ep>;
+					};
+				};
+
+				port@13 {
+					reg = <0x13>;
+
+					xbar_admaif19_ep: endpoint {
+						remote-endpoint = <&admaif19_ep>;
+					};
+				};
+
+				xbar_i2s1_port: port@14 {
+					reg = <0x14>;
+
+					xbar_i2s1_ep: endpoint {
+						remote-endpoint = <&i2s1_cif_ep>;
+					};
+				};
+
+				xbar_i2s3_port: port@16 {
+					reg = <0x16>;
+
+					xbar_i2s3_ep: endpoint {
+						remote-endpoint = <&i2s3_cif_ep>;
+					};
+				};
+
+				xbar_dmic1_port: port@1a {
+					reg = <0x1a>;
+
+					xbar_dmic1_ep: endpoint {
+						remote-endpoint = <&dmic1_cif_ep>;
+					};
+				};
+
+				xbar_dmic2_port: port@1b {
+					reg = <0x1b>;
+
+					xbar_dmic2_ep: endpoint {
+						remote-endpoint = <&dmic2_cif_ep>;
+					};
+				};
+			};
+
+			admaif@290f000 {
+				status = "okay";
+
+				ports {
+					#address-cells = <1>;
+					#size-cells = <0>;
+
+					admaif0_port: port@0 {
+						reg = <0x0>;
+
+						admaif0_ep: endpoint {
+							remote-endpoint = <&xbar_admaif0_ep>;
+						};
+					};
+
+					admaif1_port: port@1 {
+						reg = <0x1>;
+
+						admaif1_ep: endpoint {
+							remote-endpoint = <&xbar_admaif1_ep>;
+						};
+					};
+
+					admaif2_port: port@2 {
+						reg = <0x2>;
+
+						admaif2_ep: endpoint {
+							remote-endpoint = <&xbar_admaif2_ep>;
+						};
+					};
+
+					admaif3_port: port@3 {
+						reg = <0x3>;
+
+						admaif3_ep: endpoint {
+							remote-endpoint = <&xbar_admaif3_ep>;
+						};
+					};
+
+					admaif4_port: port@4 {
+						reg = <0x4>;
+
+						admaif4_ep: endpoint {
+							remote-endpoint = <&xbar_admaif4_ep>;
+						};
+					};
+
+					admaif5_port: port@5 {
+						reg = <0x5>;
+
+						admaif5_ep: endpoint {
+							remote-endpoint = <&xbar_admaif5_ep>;
+						};
+					};
+
+					admaif6_port: port@6 {
+						reg = <0x6>;
+
+						admaif6_ep: endpoint {
+							remote-endpoint = <&xbar_admaif6_ep>;
+						};
+					};
+
+					admaif7_port: port@7 {
+						reg = <0x7>;
+
+						admaif7_ep: endpoint {
+							remote-endpoint = <&xbar_admaif7_ep>;
+						};
+					};
+
+					admaif8_port: port@8 {
+						reg = <0x8>;
+
+						admaif8_ep: endpoint {
+							remote-endpoint = <&xbar_admaif8_ep>;
+						};
+					};
+
+					admaif9_port: port@9 {
+						reg = <0x9>;
+
+						admaif9_ep: endpoint {
+							remote-endpoint = <&xbar_admaif9_ep>;
+						};
+					};
+
+					admaif10_port: port@a {
+						reg = <0xa>;
+
+						admaif10_ep: endpoint {
+							remote-endpoint = <&xbar_admaif10_ep>;
+						};
+					};
+
+					admaif11_port: port@b {
+						reg = <0xb>;
+
+						admaif11_ep: endpoint {
+							remote-endpoint = <&xbar_admaif11_ep>;
+						};
+					};
+
+					admaif12_port: port@c {
+						reg = <0xc>;
+
+						admaif12_ep: endpoint {
+							remote-endpoint = <&xbar_admaif12_ep>;
+						};
+					};
+
+					admaif13_port: port@d {
+						reg = <0xd>;
+
+						admaif13_ep: endpoint {
+							remote-endpoint = <&xbar_admaif13_ep>;
+						};
+					};
+
+					admaif14_port: port@e {
+						reg = <0xe>;
+
+						admaif14_ep: endpoint {
+							remote-endpoint = <&xbar_admaif14_ep>;
+						};
+					};
+
+					admaif15_port: port@f {
+						reg = <0xf>;
+
+						admaif15_ep: endpoint {
+							remote-endpoint = <&xbar_admaif15_ep>;
+						};
+					};
+
+					admaif16_port: port@10 {
+						reg = <0x10>;
+
+						admaif16_ep: endpoint {
+							remote-endpoint = <&xbar_admaif16_ep>;
+						};
+					};
+
+					admaif17_port: port@11 {
+						reg = <0x11>;
+
+						admaif17_ep: endpoint {
+							remote-endpoint = <&xbar_admaif17_ep>;
+						};
+					};
+
+					admaif18_port: port@12 {
+						reg = <0x12>;
+
+						admaif18_ep: endpoint {
+							remote-endpoint = <&xbar_admaif18_ep>;
+						};
+					};
+
+					admaif19_port: port@13 {
+						reg = <0x13>;
+
+						admaif19_ep: endpoint {
+							remote-endpoint = <&xbar_admaif19_ep>;
+						};
+					};
+				};
+			};
+
+			i2s@2901000 {
+				status = "okay";
+
+				ports {
+					#address-cells = <1>;
+					#size-cells = <0>;
+
+					port@0 {
+						reg = <0>;
+
+						i2s1_cif_ep: endpoint {
+							remote-endpoint = <&xbar_i2s1_ep>;
+						};
+					};
+
+					i2s1_port: port@1 {
+						reg = <1>;
+
+						i2s1_dap_ep: endpoint {
+							dai-format = "i2s";
+							/* Placeholder for external Codec */
+						};
+					};
+				};
+			};
+
+			i2s@2901200 {
+				status = "okay";
+
+				ports {
+					#address-cells = <1>;
+					#size-cells = <0>;
+
+					port@0 {
+						reg = <0>;
+
+						i2s3_cif_ep: endpoint {
+							remote-endpoint = <&xbar_i2s3_ep>;
+						};
+					};
+
+					i2s3_port: port@1 {
+						reg = <1>;
+
+						i2s3_dap_ep: endpoint {
+							dai-format = "i2s";
+							/* Placeholder for external Codec */
+						};
+					};
+				};
+			};
+
+			dmic@2904000 {
+				status = "okay";
+
+				ports {
+					#address-cells = <1>;
+					#size-cells = <0>;
+
+					port@0 {
+						reg = <0>;
+
+						dmic1_cif_ep: endpoint {
+							remote-endpoint = <&xbar_dmic1_ep>;
+						};
+					};
+
+					dmic1_port: port@1 {
+						reg = <1>;
+
+						dmic1_dap_ep: endpoint {
+							/* Place holder for external Codec */
+						};
+					};
+				};
+			};
+
+			dmic@2904100 {
+				status = "okay";
+
+				ports {
+					#address-cells = <1>;
+					#size-cells = <0>;
+
+					port@0 {
+						reg = <0>;
+
+						dmic2_cif_ep: endpoint {
+							remote-endpoint = <&xbar_dmic2_ep>;
+						};
+					};
+
+					dmic2_port: port@1 {
+						reg = <1>;
+
+						dmic2_dap_ep: endpoint {
+							/* Place holder for external Codec */
+						};
+					};
+				};
+			};
+		};
+	};
+
+	sound {
+		compatible = "nvidia,tegra186-audio-graph-card";
+		status = "okay";
+
+		dais = /* FE */
+		       <&admaif0_port>, <&admaif1_port>, <&admaif2_port>, <&admaif3_port>,
+		       <&admaif4_port>, <&admaif5_port>, <&admaif6_port>, <&admaif7_port>,
+		       <&admaif8_port>, <&admaif9_port>, <&admaif10_port>, <&admaif11_port>,
+		       <&admaif12_port>, <&admaif13_port>, <&admaif14_port>, <&admaif15_port>,
+		       <&admaif16_port>, <&admaif17_port>, <&admaif18_port>, <&admaif19_port>,
+		       /* Router */
+		       <&xbar_i2s1_port>, <&xbar_i2s3_port>,
+		       <&xbar_dmic1_port>, <&xbar_dmic2_port>,
+		       /* I/O */
+		       <&i2s1_port>, <&i2s3_port>,
+		       <&dmic1_port>, <&dmic2_port>;
+
+		label = "NVIDIA Jetson TX2 NX APE";
+	};
 };
diff --git a/arch/arm64/boot/dts/nvidia/tegra186.dtsi b/arch/arm64/boot/dts/nvidia/tegra186.dtsi
index e94f8add1a40..9ac4f0140700 100644
--- a/arch/arm64/boot/dts/nvidia/tegra186.dtsi
+++ b/arch/arm64/boot/dts/nvidia/tegra186.dtsi
@@ -354,6 +354,126 @@
 				sound-name-prefix = "DSPK2";
 				status = "disabled";
 			};
+
+			tegra_sfc1: sfc@2902000 {
+				compatible = "nvidia,tegra186-sfc",
+					     "nvidia,tegra210-sfc";
+				reg = <0x2902000 0x200>;
+				sound-name-prefix = "SFC1";
+				status = "disabled";
+			};
+
+			tegra_sfc2: sfc@2902200 {
+				compatible = "nvidia,tegra186-sfc",
+					     "nvidia,tegra210-sfc";
+				reg = <0x2902200 0x200>;
+				sound-name-prefix = "SFC2";
+				status = "disabled";
+			};
+
+			tegra_sfc3: sfc@2902400 {
+				compatible = "nvidia,tegra186-sfc",
+					     "nvidia,tegra210-sfc";
+				reg = <0x2902400 0x200>;
+				sound-name-prefix = "SFC3";
+				status = "disabled";
+			};
+
+			tegra_sfc4: sfc@2902600 {
+				compatible = "nvidia,tegra186-sfc",
+					     "nvidia,tegra210-sfc";
+				reg = <0x2902600 0x200>;
+				sound-name-prefix = "SFC4";
+				status = "disabled";
+			};
+
+			tegra_mvc1: mvc@290a000 {
+				compatible = "nvidia,tegra186-mvc",
+					     "nvidia,tegra210-mvc";
+				reg = <0x290a000 0x200>;
+				sound-name-prefix = "MVC1";
+				status = "disabled";
+			};
+
+			tegra_mvc2: mvc@290a200 {
+				compatible = "nvidia,tegra186-mvc",
+					     "nvidia,tegra210-mvc";
+				reg = <0x290a200 0x200>;
+				sound-name-prefix = "MVC2";
+				status = "disabled";
+			};
+
+			tegra_amx1: amx@2903000 {
+				compatible = "nvidia,tegra186-amx",
+					     "nvidia,tegra210-amx";
+				reg = <0x2903000 0x100>;
+				sound-name-prefix = "AMX1";
+				status = "disabled";
+			};
+
+			tegra_amx2: amx@2903100 {
+				compatible = "nvidia,tegra186-amx",
+					     "nvidia,tegra210-amx";
+				reg = <0x2903100 0x100>;
+				sound-name-prefix = "AMX2";
+				status = "disabled";
+			};
+
+			tegra_amx3: amx@2903200 {
+				compatible = "nvidia,tegra186-amx",
+					     "nvidia,tegra210-amx";
+				reg = <0x2903200 0x100>;
+				sound-name-prefix = "AMX3";
+				status = "disabled";
+			};
+
+			tegra_amx4: amx@2903300 {
+				compatible = "nvidia,tegra186-amx",
+					     "nvidia,tegra210-amx";
+				reg = <0x2903300 0x100>;
+				sound-name-prefix = "AMX4";
+				status = "disabled";
+			};
+
+			tegra_adx1: adx@2903800 {
+				compatible = "nvidia,tegra186-adx",
+					     "nvidia,tegra210-adx";
+				reg = <0x2903800 0x100>;
+				sound-name-prefix = "ADX1";
+				status = "disabled";
+			};
+
+			tegra_adx2: adx@2903900 {
+				compatible = "nvidia,tegra186-adx",
+					     "nvidia,tegra210-adx";
+				reg = <0x2903900 0x100>;
+				sound-name-prefix = "ADX2";
+				status = "disabled";
+			};
+
+			tegra_adx3: adx@2903a00 {
+				compatible = "nvidia,tegra186-adx",
+					     "nvidia,tegra210-adx";
+				reg = <0x2903a00 0x100>;
+				sound-name-prefix = "ADX3";
+				status = "disabled";
+			};
+
+			tegra_adx4: adx@2903b00 {
+				compatible = "nvidia,tegra186-adx",
+					     "nvidia,tegra210-adx";
+				reg = <0x2903b00 0x100>;
+				sound-name-prefix = "ADX4";
+				status = "disabled";
+			};
+
+			tegra_amixer: amixer@290bb00 {
+				compatible = "nvidia,tegra186-amixer",
+					     "nvidia,tegra210-amixer";
+				reg = <0x290bb00 0x800>;
+				sound-name-prefix = "MIXER1";
+				status = "disabled";
+			};
 		};
 	};
 
@@ -1433,6 +1553,22 @@
 			power-domains = <&bpmp TEGRA186_POWER_DOMAIN_DISP>;
 		};
 
+		nvdec@15480000 {
+			compatible = "nvidia,tegra186-nvdec";
+			reg = <0x15480000 0x40000>;
+			clocks = <&bpmp TEGRA186_CLK_NVDEC>;
+			clock-names = "nvdec";
+			resets = <&bpmp TEGRA186_RESET_NVDEC>;
+			reset-names = "nvdec";
+
+			power-domains = <&bpmp TEGRA186_POWER_DOMAIN_NVDEC>;
+			interconnects = <&mc TEGRA186_MEMORY_CLIENT_NVDECSRD &emc>,
+					<&mc TEGRA186_MEMORY_CLIENT_NVDECSRD1 &emc>,
+					<&mc TEGRA186_MEMORY_CLIENT_NVDECSWR &emc>;
+			interconnect-names = "dma-mem", "read-1", "write";
+			iommus = <&smmu TEGRA186_SID_NVDEC>;
+		};
+
 		sor0: sor@15540000 {
 			compatible = "nvidia,tegra186-sor";
 			reg = <0x15540000 0x10000>;
diff --git a/arch/arm64/boot/dts/nvidia/tegra194-p2972-0000.dts b/arch/arm64/boot/dts/nvidia/tegra194-p2972-0000.dts
index 96bd01cadb18..9f34871b8f60 100644
--- a/arch/arm64/boot/dts/nvidia/tegra194-p2972-0000.dts
+++ b/arch/arm64/boot/dts/nvidia/tegra194-p2972-0000.dts
@@ -228,6 +228,542 @@
 							remote-endpoint = <&dmic3_cif_ep>;
 						};
 					};
+
+					xbar_sfc1_in_port: port@20 {
+						reg = <0x20>;
+
+						xbar_sfc1_in_ep: endpoint {
+							remote-endpoint = <&sfc1_cif_in_ep>;
+						};
+					};
+
+					port@21 {
+						reg = <0x21>;
+
+						xbar_sfc1_out_ep: endpoint {
+							remote-endpoint = <&sfc1_cif_out_ep>;
+						};
+					};
+
+					xbar_sfc2_in_port: port@22 {
+						reg = <0x22>;
+
+						xbar_sfc2_in_ep: endpoint {
+							remote-endpoint = <&sfc2_cif_in_ep>;
+						};
+					};
+
+					port@23 {
+						reg = <0x23>;
+
+						xbar_sfc2_out_ep: endpoint {
+							remote-endpoint = <&sfc2_cif_out_ep>;
+						};
+					};
+
+					xbar_sfc3_in_port: port@24 {
+						reg = <0x24>;
+
+						xbar_sfc3_in_ep: endpoint {
+							remote-endpoint = <&sfc3_cif_in_ep>;
+						};
+					};
+
+					port@25 {
+						reg = <0x25>;
+
+						xbar_sfc3_out_ep: endpoint {
+							remote-endpoint = <&sfc3_cif_out_ep>;
+						};
+					};
+
+					xbar_sfc4_in_port: port@26 {
+						reg = <0x26>;
+
+						xbar_sfc4_in_ep: endpoint {
+							remote-endpoint = <&sfc4_cif_in_ep>;
+						};
+					};
+
+					port@27 {
+						reg = <0x27>;
+
+						xbar_sfc4_out_ep: endpoint {
+							remote-endpoint = <&sfc4_cif_out_ep>;
+						};
+					};
+
+					xbar_mvc1_in_port: port@28 {
+						reg = <0x28>;
+
+						xbar_mvc1_in_ep: endpoint {
+							remote-endpoint = <&mvc1_cif_in_ep>;
+						};
+					};
+
+					port@29 {
+						reg = <0x29>;
+
+						xbar_mvc1_out_ep: endpoint {
+							remote-endpoint = <&mvc1_cif_out_ep>;
+						};
+					};
+
+					xbar_mvc2_in_port: port@2a {
+						reg = <0x2a>;
+
+						xbar_mvc2_in_ep: endpoint {
+							remote-endpoint = <&mvc2_cif_in_ep>;
+						};
+					};
+
+					port@2b {
+						reg = <0x2b>;
+
+						xbar_mvc2_out_ep: endpoint {
+							remote-endpoint = <&mvc2_cif_out_ep>;
+						};
+					};
+
+					xbar_amx1_in1_port: port@2c {
+						reg = <0x2c>;
+
+						xbar_amx1_in1_ep: endpoint {
+							remote-endpoint = <&amx1_in1_ep>;
+						};
+					};
+
+					xbar_amx1_in2_port: port@2d {
+						reg = <0x2d>;
+
+						xbar_amx1_in2_ep: endpoint {
+							remote-endpoint = <&amx1_in2_ep>;
+						};
+					};
+
+					xbar_amx1_in3_port: port@2e {
+						reg = <0x2e>;
+
+						xbar_amx1_in3_ep: endpoint {
+							remote-endpoint = <&amx1_in3_ep>;
+						};
+					};
+
+					xbar_amx1_in4_port: port@2f {
+						reg = <0x2f>;
+
+						xbar_amx1_in4_ep: endpoint {
+							remote-endpoint = <&amx1_in4_ep>;
+						};
+					};
+
+					port@30 {
+						reg = <0x30>;
+
+						xbar_amx1_out_ep: endpoint {
+							remote-endpoint = <&amx1_out_ep>;
+						};
+					};
+
+					xbar_amx2_in1_port: port@31 {
+						reg = <0x31>;
+
+						xbar_amx2_in1_ep: endpoint {
+							remote-endpoint = <&amx2_in1_ep>;
+						};
+					};
+
+					xbar_amx2_in2_port: port@32 {
+						reg = <0x32>;
+
+						xbar_amx2_in2_ep: endpoint {
+							remote-endpoint = <&amx2_in2_ep>;
+						};
+					};
+
+					xbar_amx2_in3_port: port@33 {
+						reg = <0x33>;
+
+						xbar_amx2_in3_ep: endpoint {
+							remote-endpoint = <&amx2_in3_ep>;
+						};
+					};
+
+					xbar_amx2_in4_port: port@34 {
+						reg = <0x34>;
+
+						xbar_amx2_in4_ep: endpoint {
+							remote-endpoint = <&amx2_in4_ep>;
+						};
+					};
+
+					port@35 {
+						reg = <0x35>;
+
+						xbar_amx2_out_ep: endpoint {
+							remote-endpoint = <&amx2_out_ep>;
+						};
+					};
+
+					xbar_amx3_in1_port: port@36 {
+						reg = <0x36>;
+
+						xbar_amx3_in1_ep: endpoint {
+							remote-endpoint = <&amx3_in1_ep>;
+						};
+					};
+
+					xbar_amx3_in2_port: port@37 {
+						reg = <0x37>;
+
+						xbar_amx3_in2_ep: endpoint {
+							remote-endpoint = <&amx3_in2_ep>;
+						};
+					};
+
+					xbar_amx3_in3_port: port@38 {
+						reg = <0x38>;
+
+						xbar_amx3_in3_ep: endpoint {
+							remote-endpoint = <&amx3_in3_ep>;
+						};
+					};
+
+					xbar_amx3_in4_port: port@39 {
+						reg = <0x39>;
+
+						xbar_amx3_in4_ep: endpoint {
+							remote-endpoint = <&amx3_in4_ep>;
+						};
+					};
+
+					port@3a {
+						reg = <0x3a>;
+
+						xbar_amx3_out_ep: endpoint {
+							remote-endpoint = <&amx3_out_ep>;
+						};
+					};
+
+					xbar_amx4_in1_port: port@3b {
+						reg = <0x3b>;
+
+						xbar_amx4_in1_ep: endpoint {
+							remote-endpoint = <&amx4_in1_ep>;
+						};
+					};
+
+					xbar_amx4_in2_port: port@3c {
+						reg = <0x3c>;
+
+						xbar_amx4_in2_ep: endpoint {
+							remote-endpoint = <&amx4_in2_ep>;
+						};
+					};
+
+					xbar_amx4_in3_port: port@3d {
+						reg = <0x3d>;
+
+						xbar_amx4_in3_ep: endpoint {
+							remote-endpoint = <&amx4_in3_ep>;
+						};
+					};
+
+					xbar_amx4_in4_port: port@3e {
+						reg = <0x3e>;
+
+						xbar_amx4_in4_ep: endpoint {
+							remote-endpoint = <&amx4_in4_ep>;
+						};
+					};
+
+					port@3f {
+						reg = <0x3f>;
+
+						xbar_amx4_out_ep: endpoint {
+							remote-endpoint = <&amx4_out_ep>;
+						};
+					};
+
+					xbar_adx1_in_port: port@40 {
+						reg = <0x40>;
+
+						xbar_adx1_in_ep: endpoint {
+							remote-endpoint = <&adx1_in_ep>;
+						};
+					};
+
+					port@41 {
+						reg = <0x41>;
+
+						xbar_adx1_out1_ep: endpoint {
+							remote-endpoint = <&adx1_out1_ep>;
+						};
+					};
+
+					port@42 {
+						reg = <0x42>;
+
+						xbar_adx1_out2_ep: endpoint {
+							remote-endpoint = <&adx1_out2_ep>;
+						};
+					};
+
+					port@43 {
+						reg = <0x43>;
+
+						xbar_adx1_out3_ep: endpoint {
+							remote-endpoint = <&adx1_out3_ep>;
+						};
+					};
+
+					port@44 {
+						reg = <0x44>;
+
+						xbar_adx1_out4_ep: endpoint {
+							remote-endpoint = <&adx1_out4_ep>;
+						};
+					};
+
+					xbar_adx2_in_port: port@45 {
+						reg = <0x45>;
+
+						xbar_adx2_in_ep: endpoint {
+							remote-endpoint = <&adx2_in_ep>;
+						};
+					};
+
+					port@46 {
+						reg = <0x46>;
+
+						xbar_adx2_out1_ep: endpoint {
+							remote-endpoint = <&adx2_out1_ep>;
+						};
+					};
+
+					port@47 {
+						reg = <0x47>;
+
+						xbar_adx2_out2_ep: endpoint {
+							remote-endpoint = <&adx2_out2_ep>;
+						};
+					};
+
+					port@48 {
+						reg = <0x48>;
+
+						xbar_adx2_out3_ep: endpoint {
+							remote-endpoint = <&adx2_out3_ep>;
+						};
+					};
+
+					port@49 {
+						reg = <0x49>;
+
+						xbar_adx2_out4_ep: endpoint {
+							remote-endpoint = <&adx2_out4_ep>;
+						};
+					};
+
+					xbar_adx3_in_port: port@4a {
+						reg = <0x4a>;
+
+						xbar_adx3_in_ep: endpoint {
+							remote-endpoint = <&adx3_in_ep>;
+						};
+					};
+
+					port@4b {
+						reg = <0x4b>;
+
+						xbar_adx3_out1_ep: endpoint {
+							remote-endpoint = <&adx3_out1_ep>;
+						};
+					};
+
+					port@4c {
+						reg = <0x4c>;
+
+						xbar_adx3_out2_ep: endpoint {
+							remote-endpoint = <&adx3_out2_ep>;
+						};
+					};
+
+					port@4d {
+						reg = <0x4d>;
+
+						xbar_adx3_out3_ep: endpoint {
+							remote-endpoint = <&adx3_out3_ep>;
+						};
+					};
+
+					port@4e {
+						reg = <0x4e>;
+
+						xbar_adx3_out4_ep: endpoint {
+							remote-endpoint = <&adx3_out4_ep>;
+						};
+					};
+
+					xbar_adx4_in_port: port@4f {
+						reg = <0x4f>;
+
+						xbar_adx4_in_ep: endpoint {
+							remote-endpoint = <&adx4_in_ep>;
+						};
+					};
+
+					port@50 {
+						reg = <0x50>;
+
+						xbar_adx4_out1_ep: endpoint {
+							remote-endpoint = <&adx4_out1_ep>;
+						};
+					};
+
+					port@51 {
+						reg = <0x51>;
+
+						xbar_adx4_out2_ep: endpoint {
+							remote-endpoint = <&adx4_out2_ep>;
+						};
+					};
+
+					port@52 {
+						reg = <0x52>;
+
+						xbar_adx4_out3_ep: endpoint {
+							remote-endpoint = <&adx4_out3_ep>;
+						};
+					};
+
+					port@53 {
+						reg = <0x53>;
+
+						xbar_adx4_out4_ep: endpoint {
+							remote-endpoint = <&adx4_out4_ep>;
+						};
+					};
+
+					xbar_mixer_in1_port: port@54 {
+						reg = <0x54>;
+
+						xbar_mixer_in1_ep: endpoint {
+							remote-endpoint = <&mixer_in1_ep>;
+						};
+					};
+
+					xbar_mixer_in2_port: port@55 {
+						reg = <0x55>;
+
+						xbar_mixer_in2_ep: endpoint {
+							remote-endpoint = <&mixer_in2_ep>;
+						};
+					};
+
+					xbar_mixer_in3_port: port@56 {
+						reg = <0x56>;
+
+						xbar_mixer_in3_ep: endpoint {
+							remote-endpoint = <&mixer_in3_ep>;
+						};
+					};
+
+					xbar_mixer_in4_port: port@57 {
+						reg = <0x57>;
+
+						xbar_mixer_in4_ep: endpoint {
+							remote-endpoint = <&mixer_in4_ep>;
+						};
+					};
+
+					xbar_mixer_in5_port: port@58 {
+						reg = <0x58>;
+
+						xbar_mixer_in5_ep: endpoint {
+							remote-endpoint = <&mixer_in5_ep>;
+						};
+					};
+
+					xbar_mixer_in6_port: port@59 {
+						reg = <0x59>;
+
+						xbar_mixer_in6_ep: endpoint {
+							remote-endpoint = <&mixer_in6_ep>;
+						};
+					};
+
+					xbar_mixer_in7_port: port@5a {
+						reg = <0x5a>;
+
+						xbar_mixer_in7_ep: endpoint {
+							remote-endpoint = <&mixer_in7_ep>;
+						};
+					};
+
+					xbar_mixer_in8_port: port@5b {
+						reg = <0x5b>;
+
+						xbar_mixer_in8_ep: endpoint {
+							remote-endpoint = <&mixer_in8_ep>;
+						};
+					};
+
+					xbar_mixer_in9_port: port@5c {
+						reg = <0x5c>;
+
+						xbar_mixer_in9_ep: endpoint {
+							remote-endpoint = <&mixer_in9_ep>;
+						};
+					};
+
+					xbar_mixer_in10_port: port@5d {
+						reg = <0x5d>;
+
+						xbar_mixer_in10_ep: endpoint {
+							remote-endpoint = <&mixer_in10_ep>;
+						};
+					};
+
+					port@5e {
+						reg = <0x5e>;
+
+						xbar_mixer_out1_ep: endpoint {
+							remote-endpoint = <&mixer_out1_ep>;
+						};
+					};
+
+					port@5f {
+						reg = <0x5f>;
+
+						xbar_mixer_out2_ep: endpoint {
+							remote-endpoint = <&mixer_out2_ep>;
+						};
+					};
+
+					port@60 {
+						reg = <0x60>;
+
+						xbar_mixer_out3_ep: endpoint {
+							remote-endpoint = <&mixer_out3_ep>;
+						};
+					};
+
+					port@61 {
+						reg = <0x61>;
+
+						xbar_mixer_out4_ep: endpoint {
+							remote-endpoint = <&mixer_out4_ep>;
+						};
+					};
+
+					port@62 {
+						reg = <0x62>;
+
+						xbar_mixer_out5_ep: endpoint {
+							remote-endpoint = <&mixer_out5_ep>;
+						};
+					};
 				};
 
 				admaif@290f000 {
@@ -527,6 +1063,677 @@
 						};
 					};
 				};
+
+				sfc@2902000 {
+					status = "okay";
+
+					ports {
+						#address-cells = <1>;
+						#size-cells = <0>;
+
+						port@0 {
+							reg = <0>;
+
+							sfc1_cif_in_ep: endpoint {
+								remote-endpoint = <&xbar_sfc1_in_ep>;
+							};
+						};
+
+						sfc1_out_port: port@1 {
+							reg = <1>;
+
+							sfc1_cif_out_ep: endpoint {
+								remote-endpoint = <&xbar_sfc1_out_ep>;
+							};
+						};
+					};
+				};
+
+				sfc@2902200 {
+					status = "okay";
+
+					ports {
+						#address-cells = <1>;
+						#size-cells = <0>;
+
+						port@0 {
+							reg = <0>;
+
+							sfc2_cif_in_ep: endpoint {
+								remote-endpoint = <&xbar_sfc2_in_ep>;
+							};
+						};
+
+						sfc2_out_port: port@1 {
+							reg = <1>;
+
+							sfc2_cif_out_ep: endpoint {
+								remote-endpoint = <&xbar_sfc2_out_ep>;
+							};
+						};
+					};
+				};
+
+				sfc@2902400 {
+					status = "okay";
+
+					ports {
+						#address-cells = <1>;
+						#size-cells = <0>;
+
+						port@0 {
+							reg = <0>;
+
+							sfc3_cif_in_ep: endpoint {
+								remote-endpoint = <&xbar_sfc3_in_ep>;
+							};
+						};
+
+						sfc3_out_port: port@1 {
+							reg = <1>;
+
+							sfc3_cif_out_ep: endpoint {
+								remote-endpoint = <&xbar_sfc3_out_ep>;
+							};
+						};
+					};
+				};
+
+				sfc@2902600 {
+					status = "okay";
+
+					ports {
+						#address-cells = <1>;
+						#size-cells = <0>;
+
+						port@0 {
+							reg = <0>;
+
+							sfc4_cif_in_ep: endpoint {
+								remote-endpoint = <&xbar_sfc4_in_ep>;
+							};
+						};
+
+						sfc4_out_port: port@1 {
+							reg = <1>;
+
+							sfc4_cif_out_ep: endpoint {
+								remote-endpoint = <&xbar_sfc4_out_ep>;
+							};
+						};
+					};
+				};
+
+				mvc@290a000 {
+					status = "okay";
+
+					ports {
+						#address-cells = <1>;
+						#size-cells = <0>;
+
+						port@0 {
+							reg = <0>;
+
+							mvc1_cif_in_ep: endpoint {
+								remote-endpoint = <&xbar_mvc1_in_ep>;
+							};
+						};
+
+						mvc1_out_port: port@1 {
+							reg = <1>;
+
+							mvc1_cif_out_ep: endpoint {
+								remote-endpoint = <&xbar_mvc1_out_ep>;
+							};
+						};
+					};
+				};
+
+				mvc@290a200 {
+					status = "okay";
+
+					ports {
+						#address-cells = <1>;
+						#size-cells = <0>;
+
+						port@0 {
+							reg = <0>;
+
+							mvc2_cif_in_ep: endpoint {
+								remote-endpoint = <&xbar_mvc2_in_ep>;
+							};
+						};
+
+						mvc2_out_port: port@1 {
+							reg = <1>;
+
+							mvc2_cif_out_ep: endpoint {
+								remote-endpoint = <&xbar_mvc2_out_ep>;
+							};
+						};
+					};
+				};
+
+				amx@2903000 {
+					status = "okay";
+
+					ports {
+						#address-cells = <1>;
+						#size-cells = <0>;
+
+						port@0 {
+							reg = <0>;
+
+							amx1_in1_ep: endpoint {
+								remote-endpoint = <&xbar_amx1_in1_ep>;
+							};
+						};
+
+						port@1 {
+							reg = <1>;
+
+							amx1_in2_ep: endpoint {
+								remote-endpoint = <&xbar_amx1_in2_ep>;
+							};
+						};
+
+						port@2 {
+							reg = <2>;
+
+							amx1_in3_ep: endpoint {
+								remote-endpoint = <&xbar_amx1_in3_ep>;
+							};
+						};
+
+						port@3 {
+							reg = <3>;
+
+							amx1_in4_ep: endpoint {
+								remote-endpoint = <&xbar_amx1_in4_ep>;
+							};
+						};
+
+						amx1_out_port: port@4 {
+							reg = <4>;
+
+							amx1_out_ep: endpoint {
+								remote-endpoint = <&xbar_amx1_out_ep>;
+							};
+						};
+					};
+				};
+
+				amx@2903100 {
+					status = "okay";
+
+					ports {
+						#address-cells = <1>;
+						#size-cells = <0>;
+
+						port@0 {
+							reg = <0>;
+
+							amx2_in1_ep: endpoint {
+								remote-endpoint = <&xbar_amx2_in1_ep>;
+							};
+						};
+
+						port@1 {
+							reg = <1>;
+
+							amx2_in2_ep: endpoint {
+								remote-endpoint = <&xbar_amx2_in2_ep>;
+							};
+						};
+
+						amx2_in3_port: port@2 {
+							reg = <2>;
+
+							amx2_in3_ep: endpoint {
+								remote-endpoint = <&xbar_amx2_in3_ep>;
+							};
+						};
+
+						amx2_in4_port: port@3 {
+							reg = <3>;
+
+							amx2_in4_ep: endpoint {
+								remote-endpoint = <&xbar_amx2_in4_ep>;
+							};
+						};
+
+						amx2_out_port: port@4 {
+							reg = <4>;
+
+							amx2_out_ep: endpoint {
+								remote-endpoint = <&xbar_amx2_out_ep>;
+							};
+						};
+					};
+				};
+
+				amx@2903200 {
+					status = "okay";
+
+					ports {
+						#address-cells = <1>;
+						#size-cells = <0>;
+
+						port@0 {
+							reg = <0>;
+
+							amx3_in1_ep: endpoint {
+								remote-endpoint = <&xbar_amx3_in1_ep>;
+							};
+						};
+
+						port@1 {
+							reg = <1>;
+
+							amx3_in2_ep: endpoint {
+								remote-endpoint = <&xbar_amx3_in2_ep>;
+							};
+						};
+
+						port@2 {
+							reg = <2>;
+
+							amx3_in3_ep: endpoint {
+								remote-endpoint = <&xbar_amx3_in3_ep>;
+							};
+						};
+
+						port@3 {
+							reg = <3>;
+
+							amx3_in4_ep: endpoint {
+								remote-endpoint = <&xbar_amx3_in4_ep>;
+							};
+						};
+
+						amx3_out_port: port@4 {
+							reg = <4>;
+
+							amx3_out_ep: endpoint {
+								remote-endpoint = <&xbar_amx3_out_ep>;
+							};
+						};
+					};
+				};
+
+				amx@2903300 {
+					status = "okay";
+
+					ports {
+						#address-cells = <1>;
+						#size-cells = <0>;
+
+						port@0 {
+							reg = <0>;
+
+							amx4_in1_ep: endpoint {
+								remote-endpoint = <&xbar_amx4_in1_ep>;
+							};
+						};
+
+						port@1 {
+							reg = <1>;
+
+							amx4_in2_ep: endpoint {
+								remote-endpoint = <&xbar_amx4_in2_ep>;
+							};
+						};
+
+						port@2 {
+							reg = <2>;
+
+							amx4_in3_ep: endpoint {
+								remote-endpoint = <&xbar_amx4_in3_ep>;
+							};
+						};
+
+						port@3 {
+							reg = <3>;
+
+							amx4_in4_ep: endpoint {
+								remote-endpoint = <&xbar_amx4_in4_ep>;
+							};
+						};
+
+						amx4_out_port: port@4 {
+							reg = <4>;
+
+							amx4_out_ep: endpoint {
+								remote-endpoint = <&xbar_amx4_out_ep>;
+							};
+						};
+					};
+				};
+
+				adx@2903800 {
+					status = "okay";
+
+					ports {
+						#address-cells = <1>;
+						#size-cells = <0>;
+
+						port@0 {
+							reg = <0>;
+
+							adx1_in_ep: endpoint {
+								remote-endpoint = <&xbar_adx1_in_ep>;
+							};
+						};
+
+						adx1_out1_port: port@1 {
+							reg = <1>;
+
+							adx1_out1_ep: endpoint {
+								remote-endpoint = <&xbar_adx1_out1_ep>;
+							};
+						};
+
+						adx1_out2_port: port@2 {
+							reg = <2>;
+
+							adx1_out2_ep: endpoint {
+								remote-endpoint = <&xbar_adx1_out2_ep>;
+							};
+						};
+
+						adx1_out3_port: port@3 {
+							reg = <3>;
+
+							adx1_out3_ep: endpoint {
+								remote-endpoint = <&xbar_adx1_out3_ep>;
+							};
+						};
+
+						adx1_out4_port: port@4 {
+							reg = <4>;
+
+							adx1_out4_ep: endpoint {
+								remote-endpoint = <&xbar_adx1_out4_ep>;
+							};
+						};
+					};
+				};
+
+				adx@2903900 {
+					status = "okay";
+
+					ports {
+						#address-cells = <1>;
+						#size-cells = <0>;
+
+						port@0 {
+							reg = <0>;
+
+							adx2_in_ep: endpoint {
+								remote-endpoint = <&xbar_adx2_in_ep>;
+							};
+						};
+
+						adx2_out1_port: port@1 {
+							reg = <1>;
+
+							adx2_out1_ep: endpoint {
+								remote-endpoint = <&xbar_adx2_out1_ep>;
+							};
+						};
+
+						adx2_out2_port: port@2 {
+							reg = <2>;
+
+							adx2_out2_ep: endpoint {
+								remote-endpoint = <&xbar_adx2_out2_ep>;
+							};
+						};
+
+						adx2_out3_port: port@3 {
+							reg = <3>;
+
+							adx2_out3_ep: endpoint {
+								remote-endpoint = <&xbar_adx2_out3_ep>;
+							};
+						};
+
+						adx2_out4_port: port@4 {
+							reg = <4>;
+
+							adx2_out4_ep: endpoint {
+								remote-endpoint = <&xbar_adx2_out4_ep>;
+							};
+						};
+					};
+				};
+
+				adx@2903a00 {
+					status = "okay";
+
+					ports {
+						#address-cells = <1>;
+						#size-cells = <0>;
+
+						port@0 {
+							reg = <0>;
+
+							adx3_in_ep: endpoint {
+								remote-endpoint = <&xbar_adx3_in_ep>;
+							};
+						};
+
+						adx3_out1_port: port@1 {
+							reg = <1>;
+
+							adx3_out1_ep: endpoint {
+								remote-endpoint = <&xbar_adx3_out1_ep>;
+							};
+						};
+
+						adx3_out2_port: port@2 {
+							reg = <2>;
+
+							adx3_out2_ep: endpoint {
+								remote-endpoint = <&xbar_adx3_out2_ep>;
+							};
+						};
+
+						adx3_out3_port: port@3 {
+							reg = <3>;
+
+							adx3_out3_ep: endpoint {
+								remote-endpoint = <&xbar_adx3_out3_ep>;
+							};
+						};
+
+						adx3_out4_port: port@4 {
+							reg = <4>;
+
+							adx3_out4_ep: endpoint {
+								remote-endpoint = <&xbar_adx3_out4_ep>;
+							};
+						};
+					};
+				};
+
+				adx@2903b00 {
+					status = "okay";
+
+					ports {
+						#address-cells = <1>;
+						#size-cells = <0>;
+
+						port@0 {
+							reg = <0>;
+
+							adx4_in_ep: endpoint {
+								remote-endpoint = <&xbar_adx4_in_ep>;
+							};
+						};
+
+						adx4_out1_port: port@1 {
+							reg = <1>;
+
+							adx4_out1_ep: endpoint {
+								remote-endpoint = <&xbar_adx4_out1_ep>;
+							};
+						};
+
+						adx4_out2_port: port@2 {
+							reg = <2>;
+
+							adx4_out2_ep: endpoint {
+								remote-endpoint = <&xbar_adx4_out2_ep>;
+							};
+						};
+
+						adx4_out3_port: port@3 {
+							reg = <3>;
+
+							adx4_out3_ep: endpoint {
+								remote-endpoint = <&xbar_adx4_out3_ep>;
+							};
+						};
+
+						adx4_out4_port: port@4 {
+							reg = <4>;
+
+							adx4_out4_ep: endpoint {
+								remote-endpoint = <&xbar_adx4_out4_ep>;
+							};
+						};
+					};
+				};
+
+				amixer@290bb00 {
+					status = "okay";
+
+					ports {
+						#address-cells = <1>;
+						#size-cells = <0>;
+
+						port@0 {
+							reg = <0x0>;
+
+							mixer_in1_ep: endpoint {
+								remote-endpoint = <&xbar_mixer_in1_ep>;
+							};
+						};
+
+						port@1 {
+							reg = <0x1>;
+
+							mixer_in2_ep: endpoint {
+								remote-endpoint = <&xbar_mixer_in2_ep>;
+							};
+						};
+
+						port@2 {
+							reg = <0x2>;
+
+							mixer_in3_ep: endpoint {
+								remote-endpoint = <&xbar_mixer_in3_ep>;
+							};
+						};
+
+						port@3 {
+							reg = <0x3>;
+
+							mixer_in4_ep: endpoint {
+								remote-endpoint = <&xbar_mixer_in4_ep>;
+							};
+						};
+
+						port@4 {
+							reg = <0x4>;
+
+							mixer_in5_ep: endpoint {
+								remote-endpoint = <&xbar_mixer_in5_ep>;
+							};
+						};
+
+						port@5 {
+							reg = <0x5>;
+
+							mixer_in6_ep: endpoint {
+								remote-endpoint = <&xbar_mixer_in6_ep>;
+							};
+						};
+
+						port@6 {
+							reg = <0x6>;
+
+							mixer_in7_ep: endpoint {
+								remote-endpoint = <&xbar_mixer_in7_ep>;
+							};
+						};
+
+						port@7 {
+							reg = <0x7>;
+
+							mixer_in8_ep: endpoint {
+								remote-endpoint = <&xbar_mixer_in8_ep>;
+							};
+						};
+
+						port@8 {
+							reg = <0x8>;
+
+							mixer_in9_ep: endpoint {
+								remote-endpoint = <&xbar_mixer_in9_ep>;
+							};
+						};
+
+						port@9 {
+							reg = <0x9>;
+
+							mixer_in10_ep: endpoint {
+								remote-endpoint = <&xbar_mixer_in10_ep>;
+							};
+						};
+
+						mixer_out1_port: port@a {
+							reg = <0xa>;
+
+							mixer_out1_ep: endpoint {
+								remote-endpoint = <&xbar_mixer_out1_ep>;
+							};
+						};
+
+						mixer_out2_port: port@b {
+							reg = <0xb>;
+
+							mixer_out2_ep: endpoint {
+								remote-endpoint = <&xbar_mixer_out2_ep>;
+							};
+						};
+
+						mixer_out3_port: port@c {
+							reg = <0xc>;
+
+							mixer_out3_ep: endpoint {
+								remote-endpoint = <&xbar_mixer_out3_ep>;
+							};
+						};
+
+						mixer_out4_port: port@d {
+							reg = <0xd>;
+
+							mixer_out4_ep: endpoint {
+								remote-endpoint = <&xbar_mixer_out4_ep>;
+							};
+						};
+
+						mixer_out5_port: port@e {
+							reg = <0xe>;
+
+							mixer_out5_ep: endpoint {
+								remote-endpoint = <&xbar_mixer_out5_ep>;
+							};
+						};
+					};
+				};
 			};
 		};
 
@@ -764,7 +1971,7 @@
 			    "p2u-5", "p2u-6", "p2u-7";
 	};
 
-	pcie_ep@141a0000 {
+	pcie-ep@141a0000 {
 		status = "disabled";
 
 		vddio-pex-ctl-supply = <&vdd_1v8ao>;
@@ -827,6 +2034,40 @@
 		       /* XBAR Ports */
 		       <&xbar_i2s1_port>, <&xbar_i2s2_port>, <&xbar_i2s4_port>,
 		       <&xbar_i2s6_port>, <&xbar_dmic3_port>,
+		       <&xbar_sfc1_in_port>, <&xbar_sfc2_in_port>,
+		       <&xbar_sfc3_in_port>, <&xbar_sfc4_in_port>,
+		       <&xbar_mvc1_in_port>, <&xbar_mvc2_in_port>,
+		       <&xbar_amx1_in1_port>, <&xbar_amx1_in2_port>,
+		       <&xbar_amx1_in3_port>, <&xbar_amx1_in4_port>,
+		       <&xbar_amx2_in1_port>, <&xbar_amx2_in2_port>,
+		       <&xbar_amx2_in3_port>, <&xbar_amx2_in4_port>,
+		       <&xbar_amx3_in1_port>, <&xbar_amx3_in2_port>,
+		       <&xbar_amx3_in3_port>, <&xbar_amx3_in4_port>,
+		       <&xbar_amx4_in1_port>, <&xbar_amx4_in2_port>,
+		       <&xbar_amx4_in3_port>, <&xbar_amx4_in4_port>,
+		       <&xbar_adx1_in_port>, <&xbar_adx2_in_port>,
+		       <&xbar_adx3_in_port>, <&xbar_adx4_in_port>,
+		       <&xbar_mixer_in1_port>, <&xbar_mixer_in2_port>,
+		       <&xbar_mixer_in3_port>, <&xbar_mixer_in4_port>,
+		       <&xbar_mixer_in5_port>, <&xbar_mixer_in6_port>,
+		       <&xbar_mixer_in7_port>, <&xbar_mixer_in8_port>,
+		       <&xbar_mixer_in9_port>, <&xbar_mixer_in10_port>,
+		       /* HW accelerators */
+		       <&sfc1_out_port>, <&sfc2_out_port>,
+		       <&sfc3_out_port>, <&sfc4_out_port>,
+		       <&mvc1_out_port>, <&mvc2_out_port>,
+		       <&amx1_out_port>, <&amx2_out_port>,
+		       <&amx3_out_port>, <&amx4_out_port>,
+		       <&adx1_out1_port>, <&adx1_out2_port>,
+		       <&adx1_out3_port>, <&adx1_out4_port>,
+		       <&adx2_out1_port>, <&adx2_out2_port>,
+		       <&adx2_out3_port>, <&adx2_out4_port>,
+		       <&adx3_out1_port>, <&adx3_out2_port>,
+		       <&adx3_out3_port>, <&adx3_out4_port>,
+		       <&adx4_out1_port>, <&adx4_out2_port>,
+		       <&adx4_out3_port>, <&adx4_out4_port>,
+		       <&mixer_out1_port>, <&mixer_out2_port>, <&mixer_out3_port>,
+		       <&mixer_out4_port>, <&mixer_out5_port>,
 		       /* BE I/O Ports */
 		       <&i2s1_port>, <&i2s2_port>, <&i2s4_port>, <&i2s6_port>,
 		       <&dmic3_port>;
diff --git a/arch/arm64/boot/dts/nvidia/tegra194-p3509-0000.dtsi b/arch/arm64/boot/dts/nvidia/tegra194-p3509-0000.dtsi
index 836a7e0a4267..a055f17218bb 100644
--- a/arch/arm64/boot/dts/nvidia/tegra194-p3509-0000.dtsi
+++ b/arch/arm64/boot/dts/nvidia/tegra194-p3509-0000.dtsi
@@ -238,6 +238,542 @@
 							remote-endpoint = <&dspk2_cif_ep>;
 						};
 					};
+
+					xbar_sfc1_in_port: port@20 {
+						reg = <0x20>;
+
+						xbar_sfc1_in_ep: endpoint {
+							remote-endpoint = <&sfc1_cif_in_ep>;
+						};
+					};
+
+					port@21 {
+						reg = <0x21>;
+
+						xbar_sfc1_out_ep: endpoint {
+							remote-endpoint = <&sfc1_cif_out_ep>;
+						};
+					};
+
+					xbar_sfc2_in_port: port@22 {
+						reg = <0x22>;
+
+						xbar_sfc2_in_ep: endpoint {
+							remote-endpoint = <&sfc2_cif_in_ep>;
+						};
+					};
+
+					port@23 {
+						reg = <0x23>;
+
+						xbar_sfc2_out_ep: endpoint {
+							remote-endpoint = <&sfc2_cif_out_ep>;
+						};
+					};
+
+					xbar_sfc3_in_port: port@24 {
+						reg = <0x24>;
+
+						xbar_sfc3_in_ep: endpoint {
+							remote-endpoint = <&sfc3_cif_in_ep>;
+						};
+					};
+
+					port@25 {
+						reg = <0x25>;
+
+						xbar_sfc3_out_ep: endpoint {
+							remote-endpoint = <&sfc3_cif_out_ep>;
+						};
+					};
+
+					xbar_sfc4_in_port: port@26 {
+						reg = <0x26>;
+
+						xbar_sfc4_in_ep: endpoint {
+							remote-endpoint = <&sfc4_cif_in_ep>;
+						};
+					};
+
+					port@27 {
+						reg = <0x27>;
+
+						xbar_sfc4_out_ep: endpoint {
+							remote-endpoint = <&sfc4_cif_out_ep>;
+						};
+					};
+
+					xbar_mvc1_in_port: port@28 {
+						reg = <0x28>;
+
+						xbar_mvc1_in_ep: endpoint {
+							remote-endpoint = <&mvc1_cif_in_ep>;
+						};
+					};
+
+					port@29 {
+						reg = <0x29>;
+
+						xbar_mvc1_out_ep: endpoint {
+							remote-endpoint = <&mvc1_cif_out_ep>;
+						};
+					};
+
+					xbar_mvc2_in_port: port@2a {
+						reg = <0x2a>;
+
+						xbar_mvc2_in_ep: endpoint {
+							remote-endpoint = <&mvc2_cif_in_ep>;
+						};
+					};
+
+					port@2b {
+						reg = <0x2b>;
+
+						xbar_mvc2_out_ep: endpoint {
+							remote-endpoint = <&mvc2_cif_out_ep>;
+						};
+					};
+
+					xbar_amx1_in1_port: port@2c {
+						reg = <0x2c>;
+
+						xbar_amx1_in1_ep: endpoint {
+							remote-endpoint = <&amx1_in1_ep>;
+						};
+					};
+
+					xbar_amx1_in2_port: port@2d {
+						reg = <0x2d>;
+
+						xbar_amx1_in2_ep: endpoint {
+							remote-endpoint = <&amx1_in2_ep>;
+						};
+					};
+
+					xbar_amx1_in3_port: port@2e {
+						reg = <0x2e>;
+
+						xbar_amx1_in3_ep: endpoint {
+							remote-endpoint = <&amx1_in3_ep>;
+						};
+					};
+
+					xbar_amx1_in4_port: port@2f {
+						reg = <0x2f>;
+
+						xbar_amx1_in4_ep: endpoint {
+							remote-endpoint = <&amx1_in4_ep>;
+						};
+					};
+
+					port@30 {
+						reg = <0x30>;
+
+						xbar_amx1_out_ep: endpoint {
+							remote-endpoint = <&amx1_out_ep>;
+						};
+					};
+
+					xbar_amx2_in1_port: port@31 {
+						reg = <0x31>;
+
+						xbar_amx2_in1_ep: endpoint {
+							remote-endpoint = <&amx2_in1_ep>;
+						};
+					};
+
+					xbar_amx2_in2_port: port@32 {
+						reg = <0x32>;
+
+						xbar_amx2_in2_ep: endpoint {
+							remote-endpoint = <&amx2_in2_ep>;
+						};
+					};
+
+					xbar_amx2_in3_port: port@33 {
+						reg = <0x33>;
+
+						xbar_amx2_in3_ep: endpoint {
+							remote-endpoint = <&amx2_in3_ep>;
+						};
+					};
+
+					xbar_amx2_in4_port: port@34 {
+						reg = <0x34>;
+
+						xbar_amx2_in4_ep: endpoint {
+							remote-endpoint = <&amx2_in4_ep>;
+						};
+					};
+
+					port@35 {
+						reg = <0x35>;
+
+						xbar_amx2_out_ep: endpoint {
+							remote-endpoint = <&amx2_out_ep>;
+						};
+					};
+
+					xbar_amx3_in1_port: port@36 {
+						reg = <0x36>;
+
+						xbar_amx3_in1_ep: endpoint {
+							remote-endpoint = <&amx3_in1_ep>;
+						};
+					};
+
+					xbar_amx3_in2_port: port@37 {
+						reg = <0x37>;
+
+						xbar_amx3_in2_ep: endpoint {
+							remote-endpoint = <&amx3_in2_ep>;
+						};
+					};
+
+					xbar_amx3_in3_port: port@38 {
+						reg = <0x38>;
+
+						xbar_amx3_in3_ep: endpoint {
+							remote-endpoint = <&amx3_in3_ep>;
+						};
+					};
+
+					xbar_amx3_in4_port: port@39 {
+						reg = <0x39>;
+
+						xbar_amx3_in4_ep: endpoint {
+							remote-endpoint = <&amx3_in4_ep>;
+						};
+					};
+
+					port@3a {
+						reg = <0x3a>;
+
+						xbar_amx3_out_ep: endpoint {
+							remote-endpoint = <&amx3_out_ep>;
+						};
+					};
+
+					xbar_amx4_in1_port: port@3b {
+						reg = <0x3b>;
+
+						xbar_amx4_in1_ep: endpoint {
+							remote-endpoint = <&amx4_in1_ep>;
+						};
+					};
+
+					xbar_amx4_in2_port: port@3c {
+						reg = <0x3c>;
+
+						xbar_amx4_in2_ep: endpoint {
+							remote-endpoint = <&amx4_in2_ep>;
+						};
+					};
+
+					xbar_amx4_in3_port: port@3d {
+						reg = <0x3d>;
+
+						xbar_amx4_in3_ep: endpoint {
+							remote-endpoint = <&amx4_in3_ep>;
+						};
+					};
+
+					xbar_amx4_in4_port: port@3e {
+						reg = <0x3e>;
+
+						xbar_amx4_in4_ep: endpoint {
+							remote-endpoint = <&amx4_in4_ep>;
+						};
+					};
+
+					port@3f {
+						reg = <0x3f>;
+
+						xbar_amx4_out_ep: endpoint {
+							remote-endpoint = <&amx4_out_ep>;
+						};
+					};
+
+					xbar_adx1_in_port: port@40 {
+						reg = <0x40>;
+
+						xbar_adx1_in_ep: endpoint {
+							remote-endpoint = <&adx1_in_ep>;
+						};
+					};
+
+					port@41 {
+						reg = <0x41>;
+
+						xbar_adx1_out1_ep: endpoint {
+							remote-endpoint = <&adx1_out1_ep>;
+						};
+					};
+
+					port@42 {
+						reg = <0x42>;
+
+						xbar_adx1_out2_ep: endpoint {
+							remote-endpoint = <&adx1_out2_ep>;
+						};
+					};
+
+					port@43 {
+						reg = <0x43>;
+
+						xbar_adx1_out3_ep: endpoint {
+							remote-endpoint = <&adx1_out3_ep>;
+						};
+					};
+
+					port@44 {
+						reg = <0x44>;
+
+						xbar_adx1_out4_ep: endpoint {
+							remote-endpoint = <&adx1_out4_ep>;
+						};
+					};
+
+					xbar_adx2_in_port: port@45 {
+						reg = <0x45>;
+
+						xbar_adx2_in_ep: endpoint {
+							remote-endpoint = <&adx2_in_ep>;
+						};
+					};
+
+					port@46 {
+						reg = <0x46>;
+
+						xbar_adx2_out1_ep: endpoint {
+							remote-endpoint = <&adx2_out1_ep>;
+						};
+					};
+
+					port@47 {
+						reg = <0x47>;
+
+						xbar_adx2_out2_ep: endpoint {
+							remote-endpoint = <&adx2_out2_ep>;
+						};
+					};
+
+					port@48 {
+						reg = <0x48>;
+
+						xbar_adx2_out3_ep: endpoint {
+							remote-endpoint = <&adx2_out3_ep>;
+						};
+					};
+
+					port@49 {
+						reg = <0x49>;
+
+						xbar_adx2_out4_ep: endpoint {
+							remote-endpoint = <&adx2_out4_ep>;
+						};
+					};
+
+					xbar_adx3_in_port: port@4a {
+						reg = <0x4a>;
+
+						xbar_adx3_in_ep: endpoint {
+							remote-endpoint = <&adx3_in_ep>;
+						};
+					};
+
+					port@4b {
+						reg = <0x4b>;
+
+						xbar_adx3_out1_ep: endpoint {
+							remote-endpoint = <&adx3_out1_ep>;
+						};
+					};
+
+					port@4c {
+						reg = <0x4c>;
+
+						xbar_adx3_out2_ep: endpoint {
+							remote-endpoint = <&adx3_out2_ep>;
+						};
+					};
+
+					port@4d {
+						reg = <0x4d>;
+
+						xbar_adx3_out3_ep: endpoint {
+							remote-endpoint = <&adx3_out3_ep>;
+						};
+					};
+
+					port@4e {
+						reg = <0x4e>;
+
+						xbar_adx3_out4_ep: endpoint {
+							remote-endpoint = <&adx3_out4_ep>;
+						};
+					};
+
+					xbar_adx4_in_port: port@4f {
+						reg = <0x4f>;
+
+						xbar_adx4_in_ep: endpoint {
+							remote-endpoint = <&adx4_in_ep>;
+						};
+					};
+
+					port@50 {
+						reg = <0x50>;
+
+						xbar_adx4_out1_ep: endpoint {
+							remote-endpoint = <&adx4_out1_ep>;
+						};
+					};
+
+					port@51 {
+						reg = <0x51>;
+
+						xbar_adx4_out2_ep: endpoint {
+							remote-endpoint = <&adx4_out2_ep>;
+						};
+					};
+
+					port@52 {
+						reg = <0x52>;
+
+						xbar_adx4_out3_ep: endpoint {
+							remote-endpoint = <&adx4_out3_ep>;
+						};
+					};
+
+					port@53 {
+						reg = <0x53>;
+
+						xbar_adx4_out4_ep: endpoint {
+							remote-endpoint = <&adx4_out4_ep>;
+						};
+					};
+
+					xbar_mixer_in1_port: port@54 {
+						reg = <0x54>;
+
+						xbar_mixer_in1_ep: endpoint {
+							remote-endpoint = <&mixer_in1_ep>;
+						};
+					};
+
+					xbar_mixer_in2_port: port@55 {
+						reg = <0x55>;
+
+						xbar_mixer_in2_ep: endpoint {
+							remote-endpoint = <&mixer_in2_ep>;
+						};
+					};
+
+					xbar_mixer_in3_port: port@56 {
+						reg = <0x56>;
+
+						xbar_mixer_in3_ep: endpoint {
+							remote-endpoint = <&mixer_in3_ep>;
+						};
+					};
+
+					xbar_mixer_in4_port: port@57 {
+						reg = <0x57>;
+
+						xbar_mixer_in4_ep: endpoint {
+							remote-endpoint = <&mixer_in4_ep>;
+						};
+					};
+
+					xbar_mixer_in5_port: port@58 {
+						reg = <0x58>;
+
+						xbar_mixer_in5_ep: endpoint {
+							remote-endpoint = <&mixer_in5_ep>;
+						};
+					};
+
+					xbar_mixer_in6_port: port@59 {
+						reg = <0x59>;
+
+						xbar_mixer_in6_ep: endpoint {
+							remote-endpoint = <&mixer_in6_ep>;
+						};
+					};
+
+					xbar_mixer_in7_port: port@5a {
+						reg = <0x5a>;
+
+						xbar_mixer_in7_ep: endpoint {
+							remote-endpoint = <&mixer_in7_ep>;
+						};
+					};
+
+					xbar_mixer_in8_port: port@5b {
+						reg = <0x5b>;
+
+						xbar_mixer_in8_ep: endpoint {
+							remote-endpoint = <&mixer_in8_ep>;
+						};
+					};
+
+					xbar_mixer_in9_port: port@5c {
+						reg = <0x5c>;
+
+						xbar_mixer_in9_ep: endpoint {
+							remote-endpoint = <&mixer_in9_ep>;
+						};
+					};
+
+					xbar_mixer_in10_port: port@5d {
+						reg = <0x5d>;
+
+						xbar_mixer_in10_ep: endpoint {
+							remote-endpoint = <&mixer_in10_ep>;
+						};
+					};
+
+					port@5e {
+						reg = <0x5e>;
+
+						xbar_mixer_out1_ep: endpoint {
+							remote-endpoint = <&mixer_out1_ep>;
+						};
+					};
+
+					port@5f {
+						reg = <0x5f>;
+
+						xbar_mixer_out2_ep: endpoint {
+							remote-endpoint = <&mixer_out2_ep>;
+						};
+					};
+
+					port@60 {
+						reg = <0x60>;
+
+						xbar_mixer_out3_ep: endpoint {
+							remote-endpoint = <&mixer_out3_ep>;
+						};
+					};
+
+					port@61 {
+						reg = <0x61>;
+
+						xbar_mixer_out4_ep: endpoint {
+							remote-endpoint = <&mixer_out4_ep>;
+						};
+					};
+
+					port@62 {
+						reg = <0x62>;
+
+						xbar_mixer_out5_ep: endpoint {
+							remote-endpoint = <&mixer_out5_ep>;
+						};
+					};
 				};
 
 				admaif@290f000 {
@@ -585,6 +1121,679 @@
 						};
 					};
 				};
+
+				sfc@2902000 {
+					status = "okay";
+
+					ports {
+						#address-cells = <1>;
+						#size-cells = <0>;
+
+						port@0 {
+							reg = <0>;
+
+							sfc1_cif_in_ep: endpoint {
+								remote-endpoint = <&xbar_sfc1_in_ep>;
+								convert-rate = <44100>;
+							};
+						};
+
+						sfc1_out_port: port@1 {
+							reg = <1>;
+
+							sfc1_cif_out_ep: endpoint {
+								remote-endpoint = <&xbar_sfc1_out_ep>;
+								convert-rate = <48000>;
+							};
+						};
+					};
+				};
+
+				sfc@2902200 {
+					status = "okay";
+
+					ports {
+						#address-cells = <1>;
+						#size-cells = <0>;
+
+						port@0 {
+							reg = <0>;
+
+							sfc2_cif_in_ep: endpoint {
+								remote-endpoint = <&xbar_sfc2_in_ep>;
+							};
+						};
+
+						sfc2_out_port: port@1 {
+							reg = <1>;
+
+							sfc2_cif_out_ep: endpoint {
+								remote-endpoint = <&xbar_sfc2_out_ep>;
+							};
+						};
+					};
+				};
+
+				sfc@2902400 {
+					status = "okay";
+
+					ports {
+						#address-cells = <1>;
+						#size-cells = <0>;
+
+						port@0 {
+							reg = <0>;
+
+							sfc3_cif_in_ep: endpoint {
+								remote-endpoint = <&xbar_sfc3_in_ep>;
+							};
+						};
+
+						sfc3_out_port: port@1 {
+							reg = <1>;
+
+							sfc3_cif_out_ep: endpoint {
+								remote-endpoint = <&xbar_sfc3_out_ep>;
+							};
+						};
+					};
+				};
+
+				sfc@2902600 {
+					status = "okay";
+
+					ports {
+						#address-cells = <1>;
+						#size-cells = <0>;
+
+						port@0 {
+							reg = <0>;
+
+							sfc4_cif_in_ep: endpoint {
+								remote-endpoint = <&xbar_sfc4_in_ep>;
+							};
+						};
+
+						sfc4_out_port: port@1 {
+							reg = <1>;
+
+							sfc4_cif_out_ep: endpoint {
+								remote-endpoint = <&xbar_sfc4_out_ep>;
+							};
+						};
+					};
+				};
+
+				mvc@290a000 {
+					status = "okay";
+
+					ports {
+						#address-cells = <1>;
+						#size-cells = <0>;
+
+						port@0 {
+							reg = <0>;
+
+							mvc1_cif_in_ep: endpoint {
+								remote-endpoint = <&xbar_mvc1_in_ep>;
+							};
+						};
+
+						mvc1_out_port: port@1 {
+							reg = <1>;
+
+							mvc1_cif_out_ep: endpoint {
+								remote-endpoint = <&xbar_mvc1_out_ep>;
+							};
+						};
+					};
+				};
+
+				mvc@290a200 {
+					status = "okay";
+
+					ports {
+						#address-cells = <1>;
+						#size-cells = <0>;
+
+						port@0 {
+							reg = <0>;
+
+							mvc2_cif_in_ep: endpoint {
+								remote-endpoint = <&xbar_mvc2_in_ep>;
+							};
+						};
+
+						mvc2_out_port: port@1 {
+							reg = <1>;
+
+							mvc2_cif_out_ep: endpoint {
+								remote-endpoint = <&xbar_mvc2_out_ep>;
+							};
+						};
+					};
+				};
+
+				amx@2903000 {
+					status = "okay";
+
+					ports {
+						#address-cells = <1>;
+						#size-cells = <0>;
+
+						port@0 {
+							reg = <0>;
+
+							amx1_in1_ep: endpoint {
+								remote-endpoint = <&xbar_amx1_in1_ep>;
+							};
+						};
+
+						port@1 {
+							reg = <1>;
+
+							amx1_in2_ep: endpoint {
+								remote-endpoint = <&xbar_amx1_in2_ep>;
+							};
+						};
+
+						port@2 {
+							reg = <2>;
+
+							amx1_in3_ep: endpoint {
+								remote-endpoint = <&xbar_amx1_in3_ep>;
+							};
+						};
+
+						port@3 {
+							reg = <3>;
+
+							amx1_in4_ep: endpoint {
+								remote-endpoint = <&xbar_amx1_in4_ep>;
+							};
+						};
+
+						amx1_out_port: port@4 {
+							reg = <4>;
+
+							amx1_out_ep: endpoint {
+								remote-endpoint = <&xbar_amx1_out_ep>;
+							};
+						};
+					};
+				};
+
+				amx@2903100 {
+					status = "okay";
+
+					ports {
+						#address-cells = <1>;
+						#size-cells = <0>;
+
+						port@0 {
+							reg = <0>;
+
+							amx2_in1_ep: endpoint {
+								remote-endpoint = <&xbar_amx2_in1_ep>;
+							};
+						};
+
+						port@1 {
+							reg = <1>;
+
+							amx2_in2_ep: endpoint {
+								remote-endpoint = <&xbar_amx2_in2_ep>;
+							};
+						};
+
+						amx2_in3_port: port@2 {
+							reg = <2>;
+
+							amx2_in3_ep: endpoint {
+								remote-endpoint = <&xbar_amx2_in3_ep>;
+							};
+						};
+
+						amx2_in4_port: port@3 {
+							reg = <3>;
+
+							amx2_in4_ep: endpoint {
+								remote-endpoint = <&xbar_amx2_in4_ep>;
+							};
+						};
+
+						amx2_out_port: port@4 {
+							reg = <4>;
+
+							amx2_out_ep: endpoint {
+								remote-endpoint = <&xbar_amx2_out_ep>;
+							};
+						};
+					};
+				};
+
+				amx@2903200 {
+					status = "okay";
+
+					ports {
+						#address-cells = <1>;
+						#size-cells = <0>;
+
+						port@0 {
+							reg = <0>;
+
+							amx3_in1_ep: endpoint {
+								remote-endpoint = <&xbar_amx3_in1_ep>;
+							};
+						};
+
+						port@1 {
+							reg = <1>;
+
+							amx3_in2_ep: endpoint {
+								remote-endpoint = <&xbar_amx3_in2_ep>;
+							};
+						};
+
+						port@2 {
+							reg = <2>;
+
+							amx3_in3_ep: endpoint {
+								remote-endpoint = <&xbar_amx3_in3_ep>;
+							};
+						};
+
+						port@3 {
+							reg = <3>;
+
+							amx3_in4_ep: endpoint {
+								remote-endpoint = <&xbar_amx3_in4_ep>;
+							};
+						};
+
+						amx3_out_port: port@4 {
+							reg = <4>;
+
+							amx3_out_ep: endpoint {
+								remote-endpoint = <&xbar_amx3_out_ep>;
+							};
+						};
+					};
+				};
+
+				amx@2903300 {
+					status = "okay";
+
+					ports {
+						#address-cells = <1>;
+						#size-cells = <0>;
+
+						port@0 {
+							reg = <0>;
+
+							amx4_in1_ep: endpoint {
+								remote-endpoint = <&xbar_amx4_in1_ep>;
+							};
+						};
+
+						port@1 {
+							reg = <1>;
+
+							amx4_in2_ep: endpoint {
+								remote-endpoint = <&xbar_amx4_in2_ep>;
+							};
+						};
+
+						port@2 {
+							reg = <2>;
+
+							amx4_in3_ep: endpoint {
+								remote-endpoint = <&xbar_amx4_in3_ep>;
+							};
+						};
+
+						port@3 {
+							reg = <3>;
+
+							amx4_in4_ep: endpoint {
+								remote-endpoint = <&xbar_amx4_in4_ep>;
+							};
+						};
+
+						amx4_out_port: port@4 {
+							reg = <4>;
+
+							amx4_out_ep: endpoint {
+								remote-endpoint = <&xbar_amx4_out_ep>;
+							};
+						};
+					};
+				};
+
+				adx@2903800 {
+					status = "okay";
+
+					ports {
+						#address-cells = <1>;
+						#size-cells = <0>;
+
+						port@0 {
+							reg = <0>;
+
+							adx1_in_ep: endpoint {
+								remote-endpoint = <&xbar_adx1_in_ep>;
+							};
+						};
+
+						adx1_out1_port: port@1 {
+							reg = <1>;
+
+							adx1_out1_ep: endpoint {
+								remote-endpoint = <&xbar_adx1_out1_ep>;
+							};
+						};
+
+						adx1_out2_port: port@2 {
+							reg = <2>;
+
+							adx1_out2_ep: endpoint {
+								remote-endpoint = <&xbar_adx1_out2_ep>;
+							};
+						};
+
+						adx1_out3_port: port@3 {
+							reg = <3>;
+
+							adx1_out3_ep: endpoint {
+								remote-endpoint = <&xbar_adx1_out3_ep>;
+							};
+						};
+
+						adx1_out4_port: port@4 {
+							reg = <4>;
+
+							adx1_out4_ep: endpoint {
+								remote-endpoint = <&xbar_adx1_out4_ep>;
+							};
+						};
+					};
+				};
+
+				adx@2903900 {
+					status = "okay";
+
+					ports {
+						#address-cells = <1>;
+						#size-cells = <0>;
+
+						port@0 {
+							reg = <0>;
+
+							adx2_in_ep: endpoint {
+								remote-endpoint = <&xbar_adx2_in_ep>;
+							};
+						};
+
+						adx2_out1_port: port@1 {
+							reg = <1>;
+
+							adx2_out1_ep: endpoint {
+								remote-endpoint = <&xbar_adx2_out1_ep>;
+							};
+						};
+
+						adx2_out2_port: port@2 {
+							reg = <2>;
+
+							adx2_out2_ep: endpoint {
+								remote-endpoint = <&xbar_adx2_out2_ep>;
+							};
+						};
+
+						adx2_out3_port: port@3 {
+							reg = <3>;
+
+							adx2_out3_ep: endpoint {
+								remote-endpoint = <&xbar_adx2_out3_ep>;
+							};
+						};
+
+						adx2_out4_port: port@4 {
+							reg = <4>;
+
+							adx2_out4_ep: endpoint {
+								remote-endpoint = <&xbar_adx2_out4_ep>;
+							};
+						};
+					};
+				};
+
+				adx@2903a00 {
+					status = "okay";
+
+					ports {
+						#address-cells = <1>;
+						#size-cells = <0>;
+
+						port@0 {
+							reg = <0>;
+
+							adx3_in_ep: endpoint {
+								remote-endpoint = <&xbar_adx3_in_ep>;
+							};
+						};
+
+						adx3_out1_port: port@1 {
+							reg = <1>;
+
+							adx3_out1_ep: endpoint {
+								remote-endpoint = <&xbar_adx3_out1_ep>;
+							};
+						};
+
+						adx3_out2_port: port@2 {
+							reg = <2>;
+
+							adx3_out2_ep: endpoint {
+								remote-endpoint = <&xbar_adx3_out2_ep>;
+							};
+						};
+
+						adx3_out3_port: port@3 {
+							reg = <3>;
+
+							adx3_out3_ep: endpoint {
+								remote-endpoint = <&xbar_adx3_out3_ep>;
+							};
+						};
+
+						adx3_out4_port: port@4 {
+							reg = <4>;
+
+							adx3_out4_ep: endpoint {
+								remote-endpoint = <&xbar_adx3_out4_ep>;
+							};
+						};
+					};
+				};
+
+				adx@2903b00 {
+					status = "okay";
+
+					ports {
+						#address-cells = <1>;
+						#size-cells = <0>;
+
+						port@0 {
+							reg = <0>;
+
+							adx4_in_ep: endpoint {
+								remote-endpoint = <&xbar_adx4_in_ep>;
+							};
+						};
+
+						adx4_out1_port: port@1 {
+							reg = <1>;
+
+							adx4_out1_ep: endpoint {
+								remote-endpoint = <&xbar_adx4_out1_ep>;
+							};
+						};
+
+						adx4_out2_port: port@2 {
+							reg = <2>;
+
+							adx4_out2_ep: endpoint {
+								remote-endpoint = <&xbar_adx4_out2_ep>;
+							};
+						};
+
+						adx4_out3_port: port@3 {
+							reg = <3>;
+
+							adx4_out3_ep: endpoint {
+								remote-endpoint = <&xbar_adx4_out3_ep>;
+							};
+						};
+
+						adx4_out4_port: port@4 {
+							reg = <4>;
+
+							adx4_out4_ep: endpoint {
+								remote-endpoint = <&xbar_adx4_out4_ep>;
+							};
+						};
+					};
+				};
+
+				amixer@290bb00 {
+					status = "okay";
+
+					ports {
+						#address-cells = <1>;
+						#size-cells = <0>;
+
+						port@0 {
+							reg = <0x0>;
+
+							mixer_in1_ep: endpoint {
+								remote-endpoint = <&xbar_mixer_in1_ep>;
+							};
+						};
+
+						port@1 {
+							reg = <0x1>;
+
+							mixer_in2_ep: endpoint {
+								remote-endpoint = <&xbar_mixer_in2_ep>;
+							};
+						};
+
+						port@2 {
+							reg = <0x2>;
+
+							mixer_in3_ep: endpoint {
+								remote-endpoint = <&xbar_mixer_in3_ep>;
+							};
+						};
+
+						port@3 {
+							reg = <0x3>;
+
+							mixer_in4_ep: endpoint {
+								remote-endpoint = <&xbar_mixer_in4_ep>;
+							};
+						};
+
+						port@4 {
+							reg = <0x4>;
+
+							mixer_in5_ep: endpoint {
+								remote-endpoint = <&xbar_mixer_in5_ep>;
+							};
+						};
+
+						port@5 {
+							reg = <0x5>;
+
+							mixer_in6_ep: endpoint {
+								remote-endpoint = <&xbar_mixer_in6_ep>;
+							};
+						};
+
+						port@6 {
+							reg = <0x6>;
+
+							mixer_in7_ep: endpoint {
+								remote-endpoint = <&xbar_mixer_in7_ep>;
+							};
+						};
+
+						port@7 {
+							reg = <0x7>;
+
+							mixer_in8_ep: endpoint {
+								remote-endpoint = <&xbar_mixer_in8_ep>;
+							};
+						};
+
+						port@8 {
+							reg = <0x8>;
+
+							mixer_in9_ep: endpoint {
+								remote-endpoint = <&xbar_mixer_in9_ep>;
+							};
+						};
+
+						port@9 {
+							reg = <0x9>;
+
+							mixer_in10_ep: endpoint {
+								remote-endpoint = <&xbar_mixer_in10_ep>;
+							};
+						};
+
+						mixer_out1_port: port@a {
+							reg = <0xa>;
+
+							mixer_out1_ep: endpoint {
+								remote-endpoint = <&xbar_mixer_out1_ep>;
+							};
+						};
+
+						mixer_out2_port: port@b {
+							reg = <0xb>;
+
+							mixer_out2_ep: endpoint {
+								remote-endpoint = <&xbar_mixer_out2_ep>;
+							};
+						};
+
+						mixer_out3_port: port@c {
+							reg = <0xc>;
+
+							mixer_out3_ep: endpoint {
+								remote-endpoint = <&xbar_mixer_out3_ep>;
+							};
+						};
+
+						mixer_out4_port: port@d {
+							reg = <0xd>;
+
+							mixer_out4_ep: endpoint {
+								remote-endpoint = <&xbar_mixer_out4_ep>;
+							};
+						};
+
+						mixer_out5_port: port@e {
+							reg = <0xe>;
+
+							mixer_out5_ep: endpoint {
+								remote-endpoint = <&xbar_mixer_out5_ep>;
+							};
+						};
+					};
+				};
 			};
 		};
 
@@ -741,7 +1950,7 @@
 			    "p2u-5", "p2u-6", "p2u-7";
 	};
 
-	pcie_ep@141a0000 {
+	pcie-ep@141a0000 {
 		status = "disabled";
 
 		vddio-pex-ctl-supply = <&vdd_1v8ao>;
@@ -850,6 +2059,41 @@
 		       <&xbar_i2s3_port>, <&xbar_i2s5_port>,
 		       <&xbar_dmic1_port>, <&xbar_dmic2_port>, <&xbar_dmic4_port>,
 		       <&xbar_dspk1_port>, <&xbar_dspk2_port>,
+		       <&xbar_sfc1_in_port>, <&xbar_sfc2_in_port>,
+		       <&xbar_sfc3_in_port>, <&xbar_sfc4_in_port>,
+		       <&xbar_mvc1_in_port>, <&xbar_mvc2_in_port>,
+		       <&xbar_amx1_in1_port>, <&xbar_amx1_in2_port>,
+		       <&xbar_amx1_in3_port>, <&xbar_amx1_in4_port>,
+		       <&xbar_amx2_in1_port>, <&xbar_amx2_in2_port>,
+		       <&xbar_amx2_in3_port>, <&xbar_amx2_in4_port>,
+		       <&xbar_amx3_in1_port>, <&xbar_amx3_in2_port>,
+		       <&xbar_amx3_in3_port>, <&xbar_amx3_in4_port>,
+		       <&xbar_amx4_in1_port>, <&xbar_amx4_in2_port>,
+		       <&xbar_amx4_in3_port>, <&xbar_amx4_in4_port>,
+		       <&xbar_adx1_in_port>, <&xbar_adx2_in_port>,
+		       <&xbar_adx3_in_port>, <&xbar_adx4_in_port>,
+		       <&xbar_mixer_in1_port>, <&xbar_mixer_in2_port>,
+		       <&xbar_mixer_in3_port>, <&xbar_mixer_in4_port>,
+		       <&xbar_mixer_in5_port>, <&xbar_mixer_in6_port>,
+		       <&xbar_mixer_in7_port>, <&xbar_mixer_in8_port>,
+		       <&xbar_mixer_in9_port>, <&xbar_mixer_in10_port>,
+		       /* HW accelerators */
+		       <&sfc1_out_port>, <&sfc2_out_port>,
+		       <&sfc3_out_port>, <&sfc4_out_port>,
+		       <&mvc1_out_port>, <&mvc2_out_port>,
+		       <&amx1_out_port>, <&amx2_out_port>,
+		       <&amx3_out_port>, <&amx4_out_port>,
+		       <&adx1_out1_port>, <&adx1_out2_port>,
+		       <&adx1_out3_port>, <&adx1_out4_port>,
+		       <&adx2_out1_port>, <&adx2_out2_port>,
+		       <&adx2_out3_port>, <&adx2_out4_port>,
+		       <&adx3_out1_port>, <&adx3_out2_port>,
+		       <&adx3_out3_port>, <&adx3_out4_port>,
+		       <&adx4_out1_port>, <&adx4_out2_port>,
+		       <&adx4_out3_port>, <&adx4_out4_port>,
+		       <&mixer_out1_port>, <&mixer_out2_port>,
+		       <&mixer_out3_port>, <&mixer_out4_port>,
+		       <&mixer_out5_port>,
 		       /* BE I/O Ports */
 		       <&i2s3_port>, <&i2s5_port>,
 		       <&dmic1_port>, <&dmic2_port>, <&dmic4_port>,
diff --git a/arch/arm64/boot/dts/nvidia/tegra194.dtsi b/arch/arm64/boot/dts/nvidia/tegra194.dtsi
index c8250a3f7891..851e049b3519 100644
--- a/arch/arm64/boot/dts/nvidia/tegra194.dtsi
+++ b/arch/arm64/boot/dts/nvidia/tegra194.dtsi
@@ -34,11 +34,53 @@
 			reg = <0x2200000 0x10000>,
 			      <0x2210000 0x10000>;
 			interrupts = <GIC_SPI 288 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 289 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 290 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 291 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 292 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 293 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 294 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 295 IRQ_TYPE_LEVEL_HIGH>,
 				     <GIC_SPI 296 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 297 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 298 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 299 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 300 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 301 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 302 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 303 IRQ_TYPE_LEVEL_HIGH>,
 				     <GIC_SPI 304 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 305 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 306 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 307 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 308 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 309 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 310 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 311 IRQ_TYPE_LEVEL_HIGH>,
 				     <GIC_SPI 312 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 313 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 314 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 315 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 316 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 317 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 318 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 319 IRQ_TYPE_LEVEL_HIGH>,
 				     <GIC_SPI 320 IRQ_TYPE_LEVEL_HIGH>,
-				     <GIC_SPI 328 IRQ_TYPE_LEVEL_HIGH>;
+				     <GIC_SPI 321 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 322 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 323 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 324 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 325 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 326 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 327 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 328 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 329 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 330 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 331 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 332 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 333 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 334 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 335 IRQ_TYPE_LEVEL_HIGH>;
 			#interrupt-cells = <2>;
 			interrupt-controller;
 			#gpio-cells = <2>;
@@ -363,6 +405,122 @@
 					sound-name-prefix = "DSPK2";
 					status = "disabled";
 				};
+
+				tegra_sfc1: sfc@2902000 {
+					compatible = "nvidia,tegra194-sfc",
+						     "nvidia,tegra210-sfc";
+					reg = <0x2902000 0x200>;
+					sound-name-prefix = "SFC1";
+					status = "disabled";
+				};
+
+				tegra_sfc2: sfc@2902200 {
+					compatible = "nvidia,tegra194-sfc",
+						     "nvidia,tegra210-sfc";
+					reg = <0x2902200 0x200>;
+					sound-name-prefix = "SFC2";
+					status = "disabled";
+				};
+
+				tegra_sfc3: sfc@2902400 {
+					compatible = "nvidia,tegra194-sfc",
+						     "nvidia,tegra210-sfc";
+					reg = <0x2902400 0x200>;
+					sound-name-prefix = "SFC3";
+					status = "disabled";
+				};
+
+				tegra_sfc4: sfc@2902600 {
+					compatible = "nvidia,tegra194-sfc",
+						     "nvidia,tegra210-sfc";
+					reg = <0x2902600 0x200>;
+					sound-name-prefix = "SFC4";
+					status = "disabled";
+				};
+
+				tegra_mvc1: mvc@290a000 {
+					compatible = "nvidia,tegra194-mvc",
+						     "nvidia,tegra210-mvc";
+					reg = <0x290a000 0x200>;
+					sound-name-prefix = "MVC1";
+					status = "disabled";
+				};
+
+				tegra_mvc2: mvc@290a200 {
+					compatible = "nvidia,tegra194-mvc",
+						     "nvidia,tegra210-mvc";
+					reg = <0x290a200 0x200>;
+					sound-name-prefix = "MVC2";
+					status = "disabled";
+				};
+
+				tegra_amx1: amx@2903000 {
+					compatible = "nvidia,tegra194-amx";
+					reg = <0x2903000 0x100>;
+					sound-name-prefix = "AMX1";
+					status = "disabled";
+				};
+
+				tegra_amx2: amx@2903100 {
+					compatible = "nvidia,tegra194-amx";
+					reg = <0x2903100 0x100>;
+					sound-name-prefix = "AMX2";
+					status = "disabled";
+				};
+
+				tegra_amx3: amx@2903200 {
+					compatible = "nvidia,tegra194-amx";
+					reg = <0x2903200 0x100>;
+					sound-name-prefix = "AMX3";
+					status = "disabled";
+				};
+
+				tegra_amx4: amx@2903300 {
+					compatible = "nvidia,tegra194-amx";
+					reg = <0x2903300 0x100>;
+					sound-name-prefix = "AMX4";
+					status = "disabled";
+				};
+
+				tegra_adx1: adx@2903800 {
+					compatible = "nvidia,tegra194-adx",
+						     "nvidia,tegra210-adx";
+					reg = <0x2903800 0x100>;
+					sound-name-prefix = "ADX1";
+					status = "disabled";
+				};
+
+				tegra_adx2: adx@2903900 {
+					compatible = "nvidia,tegra194-adx",
+						     "nvidia,tegra210-adx";
+					reg = <0x2903900 0x100>;
+					sound-name-prefix = "ADX2";
+					status = "disabled";
+				};
+
+				tegra_adx3: adx@2903a00 {
+					compatible = "nvidia,tegra194-adx",
+						     "nvidia,tegra210-adx";
+					reg = <0x2903a00 0x100>;
+					sound-name-prefix = "ADX3";
+					status = "disabled";
+				};
+
+				tegra_adx4: adx@2903b00 {
+					compatible = "nvidia,tegra194-adx",
+						     "nvidia,tegra210-adx";
+					reg = <0x2903b00 0x100>;
+					sound-name-prefix = "ADX4";
+					status = "disabled";
+				};
+
+				tegra_amixer: amixer@290bb00 {
+					compatible = "nvidia,tegra194-amixer",
+						     "nvidia,tegra210-amixer";
+					reg = <0x290bb00 0x800>;
+					sound-name-prefix = "MIXER1";
+					status = "disabled";
+				};
 			};
 		};
 
@@ -1281,7 +1439,10 @@
 			reg-names = "security", "gpio";
 			reg = <0xc2f0000 0x1000>,
 			      <0xc2f1000 0x1000>;
-			interrupts = <GIC_SPI 56 IRQ_TYPE_LEVEL_HIGH>;
+			interrupts = <GIC_SPI 56 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 57 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 58 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 59 IRQ_TYPE_LEVEL_HIGH>;
 			gpio-controller;
 			#gpio-cells = <2>;
 			interrupt-controller;
@@ -1412,6 +1573,25 @@
 			interconnect-names = "dma-mem";
 			iommus = <&smmu TEGRA194_SID_HOST1X>;
 
+			nvdec@15140000 {
+				compatible = "nvidia,tegra194-nvdec";
+				reg = <0x15140000 0x00040000>;
+				clocks = <&bpmp TEGRA194_CLK_NVDEC1>;
+				clock-names = "nvdec";
+				resets = <&bpmp TEGRA194_RESET_NVDEC1>;
+				reset-names = "nvdec";
+
+				power-domains = <&bpmp TEGRA194_POWER_DOMAIN_NVDECB>;
+				interconnects = <&mc TEGRA194_MEMORY_CLIENT_NVDEC1SRD &emc>,
+						<&mc TEGRA194_MEMORY_CLIENT_NVDEC1SRD1 &emc>,
+						<&mc TEGRA194_MEMORY_CLIENT_NVDEC1SWR &emc>;
+				interconnect-names = "dma-mem", "read-1", "write";
+				iommus = <&smmu TEGRA194_SID_NVDEC1>;
+				dma-coherent;
+
+				nvidia,host1x-class = <0xf5>;
+			};
+
 			display-hub@15200000 {
 				compatible = "nvidia,tegra194-display";
 				reg = <0x15200000 0x00040000>;
@@ -1525,6 +1705,25 @@
 				iommus = <&smmu TEGRA194_SID_VIC>;
 			};
 
+			nvdec@15480000 {
+				compatible = "nvidia,tegra194-nvdec";
+				reg = <0x15480000 0x00040000>;
+				clocks = <&bpmp TEGRA194_CLK_NVDEC>;
+				clock-names = "nvdec";
+				resets = <&bpmp TEGRA194_RESET_NVDEC>;
+				reset-names = "nvdec";
+
+				power-domains = <&bpmp TEGRA194_POWER_DOMAIN_NVDECA>;
+				interconnects = <&mc TEGRA194_MEMORY_CLIENT_NVDECSRD &emc>,
+						<&mc TEGRA194_MEMORY_CLIENT_NVDECSRD1 &emc>,
+						<&mc TEGRA194_MEMORY_CLIENT_NVDECSWR &emc>;
+				interconnect-names = "dma-mem", "read-1", "write";
+				iommus = <&smmu TEGRA194_SID_NVDEC>;
+				dma-coherent;
+
+				nvidia,host1x-class = <0xf0>;
+			};
+
 			dpaux0: dpaux@155c0000 {
 				compatible = "nvidia,tegra194-dpaux";
 				reg = <0x155c0000 0x10000>;
@@ -2121,7 +2320,7 @@
 		dma-coherent;
 	};
 
-	pcie_ep@14160000 {
+	pcie-ep@14160000 {
 		compatible = "nvidia,tegra194-pcie-ep";
 		power-domains = <&bpmp TEGRA194_POWER_DOMAIN_PCIEX4A>;
 		reg = <0x00 0x14160000 0x0 0x00020000>, /* appl registers (128K)      */
@@ -2161,7 +2360,7 @@
 		dma-coherent;
 	};
 
-	pcie_ep@14180000 {
+	pcie-ep@14180000 {
 		compatible = "nvidia,tegra194-pcie-ep";
 		power-domains = <&bpmp TEGRA194_POWER_DOMAIN_PCIEX8B>;
 		reg = <0x00 0x14180000 0x0 0x00020000>, /* appl registers (128K)      */
@@ -2201,7 +2400,7 @@
 		dma-coherent;
 	};
 
-	pcie_ep@141a0000 {
+	pcie-ep@141a0000 {
 		compatible = "nvidia,tegra194-pcie-ep";
 		power-domains = <&bpmp TEGRA194_POWER_DOMAIN_PCIEX8A>;
 		reg = <0x00 0x141a0000 0x0 0x00020000>, /* appl registers (128K)      */
diff --git a/arch/arm64/boot/dts/nvidia/tegra210-p2371-2180.dts b/arch/arm64/boot/dts/nvidia/tegra210-p2371-2180.dts
index 7d3e3634743e..2e17df6f20ad 100644
--- a/arch/arm64/boot/dts/nvidia/tegra210-p2371-2180.dts
+++ b/arch/arm64/boot/dts/nvidia/tegra210-p2371-2180.dts
@@ -339,6 +339,481 @@
 				};
 			};
 
+			sfc@702d2000 {
+				status = "okay";
+
+				ports {
+					#address-cells = <1>;
+					#size-cells = <0>;
+
+					port@0 {
+						reg = <0>;
+
+						sfc1_cif_in_ep: endpoint {
+							remote-endpoint = <&xbar_sfc1_in_ep>;
+						};
+					};
+
+					sfc1_out_port: port@1 {
+						reg = <1>;
+
+						sfc1_cif_out_ep: endpoint {
+							remote-endpoint = <&xbar_sfc1_out_ep>;
+						};
+					};
+				};
+			};
+
+			sfc@702d2200 {
+				status = "okay";
+
+				ports {
+					#address-cells = <1>;
+					#size-cells = <0>;
+
+					port@0 {
+						reg = <0>;
+
+						sfc2_cif_in_ep: endpoint {
+							remote-endpoint = <&xbar_sfc2_in_ep>;
+						};
+					};
+
+					sfc2_out_port: port@1 {
+						reg = <1>;
+
+						sfc2_cif_out_ep: endpoint {
+							remote-endpoint = <&xbar_sfc2_out_ep>;
+						};
+					};
+				};
+			};
+
+			sfc@702d2400 {
+				status = "okay";
+
+				ports {
+					#address-cells = <1>;
+					#size-cells = <0>;
+
+					port@0 {
+						reg = <0>;
+
+						sfc3_cif_in_ep: endpoint {
+							remote-endpoint = <&xbar_sfc3_in_ep>;
+						};
+					};
+
+					sfc3_out_port: port@1 {
+						reg = <1>;
+
+						sfc3_cif_out_ep: endpoint {
+							remote-endpoint = <&xbar_sfc3_out_ep>;
+						};
+					};
+				};
+			};
+
+			sfc@702d2600 {
+				status = "okay";
+
+				ports {
+					#address-cells = <1>;
+					#size-cells = <0>;
+
+					port@0 {
+						reg = <0>;
+
+						sfc4_cif_in_ep: endpoint {
+							remote-endpoint = <&xbar_sfc4_in_ep>;
+						};
+					};
+
+					sfc4_out_port: port@1 {
+						reg = <1>;
+
+						sfc4_cif_out_ep: endpoint {
+							remote-endpoint = <&xbar_sfc4_out_ep>;
+						};
+					};
+				};
+			};
+
+			mvc@702da000 {
+				status = "okay";
+
+				ports {
+					#address-cells = <1>;
+					#size-cells = <0>;
+
+					port@0 {
+						reg = <0>;
+
+						mvc1_cif_in_ep: endpoint {
+							remote-endpoint = <&xbar_mvc1_in_ep>;
+						};
+					};
+
+					mvc1_out_port: port@1 {
+						reg = <1>;
+
+						mvc1_cif_out_ep: endpoint {
+							remote-endpoint = <&xbar_mvc1_out_ep>;
+						};
+					};
+				};
+			};
+
+			mvc@702da200 {
+				status = "okay";
+
+				ports {
+					#address-cells = <1>;
+					#size-cells = <0>;
+
+					port@0 {
+						reg = <0>;
+
+						mvc2_cif_in_ep: endpoint {
+							remote-endpoint = <&xbar_mvc2_in_ep>;
+						};
+					};
+
+					mvc2_out_port: port@1 {
+						reg = <1>;
+
+						mvc2_cif_out_ep: endpoint {
+							remote-endpoint = <&xbar_mvc2_out_ep>;
+						};
+					};
+				};
+			};
+
+			amx@702d3000 {
+				status = "okay";
+
+				ports {
+					#address-cells = <1>;
+					#size-cells = <0>;
+
+					port@0 {
+						reg = <0>;
+
+						amx1_in1_ep: endpoint {
+							remote-endpoint = <&xbar_amx1_in1_ep>;
+						};
+					};
+
+					port@1 {
+						reg = <1>;
+
+						amx1_in2_ep: endpoint {
+							remote-endpoint = <&xbar_amx1_in2_ep>;
+						};
+					};
+
+					port@2 {
+						reg = <2>;
+
+						amx1_in3_ep: endpoint {
+							remote-endpoint = <&xbar_amx1_in3_ep>;
+						};
+					};
+
+					port@3 {
+						reg = <3>;
+
+						amx1_in4_ep: endpoint {
+							remote-endpoint = <&xbar_amx1_in4_ep>;
+						};
+					};
+
+					amx1_out_port: port@4 {
+						reg = <4>;
+
+						amx1_out_ep: endpoint {
+							remote-endpoint = <&xbar_amx1_out_ep>;
+						};
+					};
+				};
+			};
+
+			amx@702d3100 {
+				status = "okay";
+
+				ports {
+					#address-cells = <1>;
+					#size-cells = <0>;
+
+					port@0 {
+						reg = <0>;
+
+						amx2_in1_ep: endpoint {
+							remote-endpoint = <&xbar_amx2_in1_ep>;
+						};
+					};
+
+					port@1 {
+						reg = <1>;
+
+						amx2_in2_ep: endpoint {
+							remote-endpoint = <&xbar_amx2_in2_ep>;
+						};
+					};
+
+					amx2_in3_port: port@2 {
+						reg = <2>;
+
+						amx2_in3_ep: endpoint {
+							remote-endpoint = <&xbar_amx2_in3_ep>;
+						};
+					};
+
+					amx2_in4_port: port@3 {
+						reg = <3>;
+
+						amx2_in4_ep: endpoint {
+							remote-endpoint = <&xbar_amx2_in4_ep>;
+						};
+					};
+
+					amx2_out_port: port@4 {
+						reg = <4>;
+
+						amx2_out_ep: endpoint {
+							remote-endpoint = <&xbar_amx2_out_ep>;
+						};
+					};
+				};
+			};
+
+			adx@702d3800 {
+				status = "okay";
+
+				ports {
+					#address-cells = <1>;
+					#size-cells = <0>;
+
+					port@0 {
+						reg = <0>;
+
+						adx1_in_ep: endpoint {
+							remote-endpoint = <&xbar_adx1_in_ep>;
+						};
+					};
+
+					adx1_out1_port: port@1 {
+						reg = <1>;
+
+						adx1_out1_ep: endpoint {
+							remote-endpoint = <&xbar_adx1_out1_ep>;
+						};
+					};
+
+					adx1_out2_port: port@2 {
+						reg = <2>;
+
+						adx1_out2_ep: endpoint {
+							remote-endpoint = <&xbar_adx1_out2_ep>;
+						};
+					};
+
+					adx1_out3_port: port@3 {
+						reg = <3>;
+
+						adx1_out3_ep: endpoint {
+							remote-endpoint = <&xbar_adx1_out3_ep>;
+						};
+					};
+
+					adx1_out4_port: port@4 {
+						reg = <4>;
+
+						adx1_out4_ep: endpoint {
+							remote-endpoint = <&xbar_adx1_out4_ep>;
+						};
+					};
+				};
+			};
+
+			adx@702d3900 {
+				status = "okay";
+
+				ports {
+					#address-cells = <1>;
+					#size-cells = <0>;
+
+					port@0 {
+						reg = <0>;
+
+						adx2_in_ep: endpoint {
+							remote-endpoint = <&xbar_adx2_in_ep>;
+						};
+					};
+
+					adx2_out1_port: port@1 {
+						reg = <1>;
+
+						adx2_out1_ep: endpoint {
+							remote-endpoint = <&xbar_adx2_out1_ep>;
+						};
+					};
+
+					adx2_out2_port: port@2 {
+						reg = <2>;
+
+						adx2_out2_ep: endpoint {
+							remote-endpoint = <&xbar_adx2_out2_ep>;
+						};
+					};
+
+					adx2_out3_port: port@3 {
+						reg = <3>;
+
+						adx2_out3_ep: endpoint {
+							remote-endpoint = <&xbar_adx2_out3_ep>;
+						};
+					};
+
+					adx2_out4_port: port@4 {
+						reg = <4>;
+
+						adx2_out4_ep: endpoint {
+							remote-endpoint = <&xbar_adx2_out4_ep>;
+						};
+					};
+				};
+			};
+
+			amixer@702dbb00 {
+				status = "okay";
+
+				ports {
+					#address-cells = <1>;
+					#size-cells = <0>;
+
+					port@0 {
+						reg = <0x0>;
+
+						mixer_in1_ep: endpoint {
+							remote-endpoint = <&xbar_mixer_in1_ep>;
+						};
+					};
+
+					port@1 {
+						reg = <0x1>;
+
+						mixer_in2_ep: endpoint {
+							remote-endpoint = <&xbar_mixer_in2_ep>;
+						};
+					};
+
+					port@2 {
+						reg = <0x2>;
+
+						mixer_in3_ep: endpoint {
+							remote-endpoint = <&xbar_mixer_in3_ep>;
+						};
+					};
+
+					port@3 {
+						reg = <0x3>;
+
+						mixer_in4_ep: endpoint {
+							remote-endpoint = <&xbar_mixer_in4_ep>;
+						};
+					};
+
+					port@4 {
+						reg = <0x4>;
+
+						mixer_in5_ep: endpoint {
+							remote-endpoint = <&xbar_mixer_in5_ep>;
+						};
+					};
+
+					port@5 {
+						reg = <0x5>;
+
+						mixer_in6_ep: endpoint {
+							remote-endpoint = <&xbar_mixer_in6_ep>;
+						};
+					};
+
+					port@6 {
+						reg = <0x6>;
+
+						mixer_in7_ep: endpoint {
+							remote-endpoint = <&xbar_mixer_in7_ep>;
+						};
+					};
+
+					port@7 {
+						reg = <0x7>;
+
+						mixer_in8_ep: endpoint {
+							remote-endpoint = <&xbar_mixer_in8_ep>;
+						};
+					};
+
+					port@8 {
+						reg = <0x8>;
+
+						mixer_in9_ep: endpoint {
+							remote-endpoint = <&xbar_mixer_in9_ep>;
+						};
+					};
+
+					port@9 {
+						reg = <0x9>;
+
+						mixer_in10_ep: endpoint {
+							remote-endpoint = <&xbar_mixer_in10_ep>;
+						};
+					};
+
+					mixer_out1_port: port@a {
+						reg = <0xa>;
+
+						mixer_out1_ep: endpoint {
+							remote-endpoint = <&xbar_mixer_out1_ep>;
+						};
+					};
+
+					mixer_out2_port: port@b {
+						reg = <0xb>;
+
+						mixer_out2_ep: endpoint {
+							remote-endpoint = <&xbar_mixer_out2_ep>;
+						};
+					};
+
+					mixer_out3_port: port@c {
+						reg = <0xc>;
+
+						mixer_out3_ep: endpoint {
+							remote-endpoint = <&xbar_mixer_out3_ep>;
+						};
+					};
+
+					mixer_out4_port: port@d {
+						reg = <0xd>;
+
+						mixer_out4_ep: endpoint {
+							remote-endpoint = <&xbar_mixer_out4_ep>;
+						};
+					};
+
+					mixer_out5_port: port@e {
+						reg = <0xe>;
+
+						mixer_out5_ep: endpoint {
+							remote-endpoint = <&xbar_mixer_out5_ep>;
+						};
+					};
+				};
+			};
+
 			ports {
 				xbar_i2s1_port: port@a {
 					reg = <0xa>;
@@ -403,6 +878,382 @@
 						remote-endpoint = <&dmic3_cif_ep>;
 					};
 				};
+
+				xbar_sfc1_in_port: port@12 {
+					reg = <0x12>;
+
+					xbar_sfc1_in_ep: endpoint {
+						remote-endpoint = <&sfc1_cif_in_ep>;
+					};
+				};
+
+				port@13 {
+					reg = <0x13>;
+
+					xbar_sfc1_out_ep: endpoint {
+						remote-endpoint = <&sfc1_cif_out_ep>;
+					};
+				};
+
+				xbar_sfc2_in_port: port@14 {
+					reg = <0x14>;
+
+					xbar_sfc2_in_ep: endpoint {
+						remote-endpoint = <&sfc2_cif_in_ep>;
+					};
+				};
+
+				port@15 {
+					reg = <0x15>;
+
+					xbar_sfc2_out_ep: endpoint {
+						remote-endpoint = <&sfc2_cif_out_ep>;
+					};
+				};
+
+				xbar_sfc3_in_port: port@16 {
+					reg = <0x16>;
+
+					xbar_sfc3_in_ep: endpoint {
+						remote-endpoint = <&sfc3_cif_in_ep>;
+					};
+				};
+
+				port@17 {
+					reg = <0x17>;
+
+					xbar_sfc3_out_ep: endpoint {
+						remote-endpoint = <&sfc3_cif_out_ep>;
+					};
+				};
+
+				xbar_sfc4_in_port: port@18 {
+					reg = <0x18>;
+
+					xbar_sfc4_in_ep: endpoint {
+						remote-endpoint = <&sfc4_cif_in_ep>;
+					};
+				};
+
+				port@19 {
+					reg = <0x19>;
+
+					xbar_sfc4_out_ep: endpoint {
+						remote-endpoint = <&sfc4_cif_out_ep>;
+					};
+				};
+
+				xbar_mvc1_in_port: port@1a {
+					reg = <0x1a>;
+
+					xbar_mvc1_in_ep: endpoint {
+						remote-endpoint = <&mvc1_cif_in_ep>;
+					};
+				};
+
+				port@1b {
+					reg = <0x1b>;
+
+					xbar_mvc1_out_ep: endpoint {
+						remote-endpoint = <&mvc1_cif_out_ep>;
+					};
+				};
+
+				xbar_mvc2_in_port: port@1c {
+					reg = <0x1c>;
+
+					xbar_mvc2_in_ep: endpoint {
+						remote-endpoint = <&mvc2_cif_in_ep>;
+					};
+				};
+
+				port@1d {
+					reg = <0x1d>;
+
+					xbar_mvc2_out_ep: endpoint {
+						remote-endpoint = <&mvc2_cif_out_ep>;
+					};
+				};
+
+				xbar_amx1_in1_port: port@1e {
+					reg = <0x1e>;
+
+					xbar_amx1_in1_ep: endpoint {
+						remote-endpoint = <&amx1_in1_ep>;
+					};
+				};
+
+				xbar_amx1_in2_port: port@1f {
+					reg = <0x1f>;
+
+					xbar_amx1_in2_ep: endpoint {
+						remote-endpoint = <&amx1_in2_ep>;
+					};
+				};
+
+				xbar_amx1_in3_port: port@20 {
+					reg = <0x20>;
+
+					xbar_amx1_in3_ep: endpoint {
+						remote-endpoint = <&amx1_in3_ep>;
+					};
+				};
+
+				xbar_amx1_in4_port: port@21 {
+					reg = <0x21>;
+
+					xbar_amx1_in4_ep: endpoint {
+						remote-endpoint = <&amx1_in4_ep>;
+					};
+				};
+
+				port@22 {
+					reg = <0x22>;
+
+					xbar_amx1_out_ep: endpoint {
+						remote-endpoint = <&amx1_out_ep>;
+					};
+				};
+
+				xbar_amx2_in1_port: port@23 {
+					reg = <0x23>;
+
+					xbar_amx2_in1_ep: endpoint {
+						remote-endpoint = <&amx2_in1_ep>;
+					};
+				};
+
+				xbar_amx2_in2_port: port@24 {
+					reg = <0x24>;
+
+					xbar_amx2_in2_ep: endpoint {
+						remote-endpoint = <&amx2_in2_ep>;
+					};
+				};
+
+				xbar_amx2_in3_port: port@25 {
+					reg = <0x25>;
+
+					xbar_amx2_in3_ep: endpoint {
+						remote-endpoint = <&amx2_in3_ep>;
+					};
+				};
+
+				xbar_amx2_in4_port: port@26 {
+					reg = <0x26>;
+
+					xbar_amx2_in4_ep: endpoint {
+						remote-endpoint = <&amx2_in4_ep>;
+					};
+				};
+
+				port@27 {
+					reg = <0x27>;
+
+					xbar_amx2_out_ep: endpoint {
+						remote-endpoint = <&amx2_out_ep>;
+					};
+				};
+
+				xbar_adx1_in_port: port@28 {
+					reg = <0x28>;
+
+					xbar_adx1_in_ep: endpoint {
+						remote-endpoint = <&adx1_in_ep>;
+					};
+				};
+
+				port@29 {
+					reg = <0x29>;
+
+					xbar_adx1_out1_ep: endpoint {
+						remote-endpoint = <&adx1_out1_ep>;
+					};
+				};
+
+				port@2a {
+					reg = <0x2a>;
+
+					xbar_adx1_out2_ep: endpoint {
+						remote-endpoint = <&adx1_out2_ep>;
+					};
+				};
+
+				port@2b {
+					reg = <0x2b>;
+
+					xbar_adx1_out3_ep: endpoint {
+						remote-endpoint = <&adx1_out3_ep>;
+					};
+				};
+
+				port@2c {
+					reg = <0x2c>;
+
+					xbar_adx1_out4_ep: endpoint {
+						remote-endpoint = <&adx1_out4_ep>;
+					};
+				};
+
+				xbar_adx2_in_port: port@2d {
+					reg = <0x2d>;
+
+					xbar_adx2_in_ep: endpoint {
+						remote-endpoint = <&adx2_in_ep>;
+					};
+				};
+
+				port@2e {
+					reg = <0x2e>;
+
+					xbar_adx2_out1_ep: endpoint {
+						remote-endpoint = <&adx2_out1_ep>;
+					};
+				};
+
+				port@2f {
+					reg = <0x2f>;
+
+					xbar_adx2_out2_ep: endpoint {
+						remote-endpoint = <&adx2_out2_ep>;
+					};
+				};
+
+				port@30 {
+					reg = <0x30>;
+
+					xbar_adx2_out3_ep: endpoint {
+						remote-endpoint = <&adx2_out3_ep>;
+					};
+				};
+
+				port@31 {
+					reg = <0x31>;
+
+					xbar_adx2_out4_ep: endpoint {
+						remote-endpoint = <&adx2_out4_ep>;
+					};
+				};
+
+				xbar_mixer_in1_port: port@32 {
+					reg = <0x32>;
+
+					xbar_mixer_in1_ep: endpoint {
+						remote-endpoint = <&mixer_in1_ep>;
+					};
+				};
+
+				xbar_mixer_in2_port: port@33 {
+					reg = <0x33>;
+
+					xbar_mixer_in2_ep: endpoint {
+						remote-endpoint = <&mixer_in2_ep>;
+					};
+				};
+
+				xbar_mixer_in3_port: port@34 {
+					reg = <0x34>;
+
+					xbar_mixer_in3_ep: endpoint {
+						remote-endpoint = <&mixer_in3_ep>;
+					};
+				};
+
+				xbar_mixer_in4_port: port@35 {
+					reg = <0x35>;
+
+					xbar_mixer_in4_ep: endpoint {
+						remote-endpoint = <&mixer_in4_ep>;
+					};
+				};
+
+				xbar_mixer_in5_port: port@36 {
+					reg = <0x36>;
+
+					xbar_mixer_in5_ep: endpoint {
+						remote-endpoint = <&mixer_in5_ep>;
+					};
+				};
+
+				xbar_mixer_in6_port: port@37 {
+					reg = <0x37>;
+
+					xbar_mixer_in6_ep: endpoint {
+						remote-endpoint = <&mixer_in6_ep>;
+					};
+				};
+
+				xbar_mixer_in7_port: port@38 {
+					reg = <0x38>;
+
+					xbar_mixer_in7_ep: endpoint {
+						remote-endpoint = <&mixer_in7_ep>;
+					};
+				};
+
+				xbar_mixer_in8_port: port@39 {
+					reg = <0x39>;
+
+					xbar_mixer_in8_ep: endpoint {
+						remote-endpoint = <&mixer_in8_ep>;
+					};
+				};
+
+				xbar_mixer_in9_port: port@3a {
+					reg = <0x3a>;
+
+					xbar_mixer_in9_ep: endpoint {
+						remote-endpoint = <&mixer_in9_ep>;
+					};
+				};
+
+				xbar_mixer_in10_port: port@3b {
+					reg = <0x3b>;
+
+					xbar_mixer_in10_ep: endpoint {
+						remote-endpoint = <&mixer_in10_ep>;
+					};
+				};
+
+				port@3c {
+					reg = <0x3c>;
+
+					xbar_mixer_out1_ep: endpoint {
+						remote-endpoint = <&mixer_out1_ep>;
+					};
+				};
+
+				port@3d {
+					reg = <0x3d>;
+
+					xbar_mixer_out2_ep: endpoint {
+						remote-endpoint = <&mixer_out2_ep>;
+					};
+				};
+
+				port@3e {
+					reg = <0x3e>;
+
+					xbar_mixer_out3_ep: endpoint {
+						remote-endpoint = <&mixer_out3_ep>;
+					};
+				};
+
+				port@3f {
+					reg = <0x3f>;
+
+					xbar_mixer_out4_ep: endpoint {
+						remote-endpoint = <&mixer_out4_ep>;
+					};
+				};
+
+				port@40 {
+					reg = <0x40>;
+
+					xbar_mixer_out5_ep: endpoint {
+						remote-endpoint = <&mixer_out5_ep>;
+					};
+				};
 			};
 		};
 	};
@@ -420,6 +1271,31 @@
 		       <&xbar_i2s1_port>, <&xbar_i2s2_port>, <&xbar_i2s3_port>,
 		       <&xbar_i2s4_port>, <&xbar_i2s5_port>, <&xbar_dmic1_port>,
 		       <&xbar_dmic2_port>, <&xbar_dmic3_port>,
+		       <&xbar_sfc1_in_port>, <&xbar_sfc2_in_port>,
+		       <&xbar_sfc3_in_port>, <&xbar_sfc4_in_port>,
+		       <&xbar_mvc1_in_port>, <&xbar_mvc2_in_port>,
+		       <&xbar_amx1_in1_port>, <&xbar_amx1_in2_port>,
+		       <&xbar_amx1_in3_port>, <&xbar_amx1_in4_port>,
+		       <&xbar_amx2_in1_port>, <&xbar_amx2_in2_port>,
+		       <&xbar_amx2_in3_port>, <&xbar_amx2_in4_port>,
+		       <&xbar_adx1_in_port>, <&xbar_adx2_in_port>,
+		       <&xbar_mixer_in1_port>, <&xbar_mixer_in2_port>,
+		       <&xbar_mixer_in3_port>, <&xbar_mixer_in4_port>,
+		       <&xbar_mixer_in5_port>, <&xbar_mixer_in6_port>,
+		       <&xbar_mixer_in7_port>, <&xbar_mixer_in8_port>,
+		       <&xbar_mixer_in9_port>, <&xbar_mixer_in10_port>,
+		       /* HW accelerators */
+		       <&sfc1_out_port>, <&sfc2_out_port>,
+		       <&sfc3_out_port>, <&sfc4_out_port>,
+		       <&mvc1_out_port>, <&mvc2_out_port>,
+		       <&amx1_out_port>, <&amx2_out_port>,
+		       <&adx1_out1_port>, <&adx1_out2_port>,
+		       <&adx1_out3_port>, <&adx1_out4_port>,
+		       <&adx2_out1_port>, <&adx2_out2_port>,
+		       <&adx2_out3_port>, <&adx2_out4_port>,
+		       <&mixer_out1_port>, <&mixer_out2_port>,
+		       <&mixer_out3_port>, <&mixer_out4_port>,
+		       <&mixer_out5_port>,
 		       /* I/O DAP Ports */
 		       <&i2s1_port>, <&i2s2_port>, <&i2s3_port>, <&i2s4_port>,
 		       <&i2s5_port>, <&dmic1_port>, <&dmic2_port>, <&dmic3_port>;
diff --git a/arch/arm64/boot/dts/nvidia/tegra210-p3450-0000.dts b/arch/arm64/boot/dts/nvidia/tegra210-p3450-0000.dts
index 7dbb13f20de7..030f264eccd5 100644
--- a/arch/arm64/boot/dts/nvidia/tegra210-p3450-0000.dts
+++ b/arch/arm64/boot/dts/nvidia/tegra210-p3450-0000.dts
@@ -746,6 +746,481 @@
 				};
 			};
 
+			sfc@702d2000 {
+				status = "okay";
+
+				ports {
+					#address-cells = <1>;
+					#size-cells = <0>;
+
+					port@0 {
+						reg = <0>;
+
+						sfc1_cif_in_ep: endpoint {
+							remote-endpoint = <&xbar_sfc1_in_ep>;
+						};
+					};
+
+					sfc1_out_port: port@1 {
+						reg = <1>;
+
+						sfc1_cif_out_ep: endpoint {
+							remote-endpoint = <&xbar_sfc1_out_ep>;
+						};
+					};
+				};
+			};
+
+			sfc@702d2200 {
+				status = "okay";
+
+				ports {
+					#address-cells = <1>;
+					#size-cells = <0>;
+
+					port@0 {
+						reg = <0>;
+
+						sfc2_cif_in_ep: endpoint {
+							remote-endpoint = <&xbar_sfc2_in_ep>;
+						};
+					};
+
+					sfc2_out_port: port@1 {
+						reg = <1>;
+
+						sfc2_cif_out_ep: endpoint {
+							remote-endpoint = <&xbar_sfc2_out_ep>;
+						};
+					};
+				};
+			};
+
+			sfc@702d2400 {
+				status = "okay";
+
+				ports {
+					#address-cells = <1>;
+					#size-cells = <0>;
+
+					port@0 {
+						reg = <0>;
+
+						sfc3_cif_in_ep: endpoint {
+							remote-endpoint = <&xbar_sfc3_in_ep>;
+						};
+					};
+
+					sfc3_out_port: port@1 {
+						reg = <1>;
+
+						sfc3_cif_out_ep: endpoint {
+							remote-endpoint = <&xbar_sfc3_out_ep>;
+						};
+					};
+				};
+			};
+
+			sfc@702d2600 {
+				status = "okay";
+
+				ports {
+					#address-cells = <1>;
+					#size-cells = <0>;
+
+					port@0 {
+						reg = <0>;
+
+						sfc4_cif_in_ep: endpoint {
+							remote-endpoint = <&xbar_sfc4_in_ep>;
+						};
+					};
+
+					sfc4_out_port: port@1 {
+						reg = <1>;
+
+						sfc4_cif_out_ep: endpoint {
+							remote-endpoint = <&xbar_sfc4_out_ep>;
+						};
+					};
+				};
+			};
+
+			mvc@702da000 {
+				status = "okay";
+
+				ports {
+					#address-cells = <1>;
+					#size-cells = <0>;
+
+					port@0 {
+						reg = <0>;
+
+						mvc1_cif_in_ep: endpoint {
+							remote-endpoint = <&xbar_mvc1_in_ep>;
+						};
+					};
+
+					mvc1_out_port: port@1 {
+						reg = <1>;
+
+						mvc1_cif_out_ep: endpoint {
+							remote-endpoint = <&xbar_mvc1_out_ep>;
+						};
+					};
+				};
+			};
+
+			mvc@702da200 {
+				status = "okay";
+
+				ports {
+					#address-cells = <1>;
+					#size-cells = <0>;
+
+					port@0 {
+						reg = <0>;
+
+						mvc2_cif_in_ep: endpoint {
+							remote-endpoint = <&xbar_mvc2_in_ep>;
+						};
+					};
+
+					mvc2_out_port: port@1 {
+						reg = <1>;
+
+						mvc2_cif_out_ep: endpoint {
+							remote-endpoint = <&xbar_mvc2_out_ep>;
+						};
+					};
+				};
+			};
+
+			amx@702d3000 {
+				status = "okay";
+
+				ports {
+					#address-cells = <1>;
+					#size-cells = <0>;
+
+					port@0 {
+						reg = <0>;
+
+						amx1_in1_ep: endpoint {
+							remote-endpoint = <&xbar_amx1_in1_ep>;
+						};
+					};
+
+					port@1 {
+						reg = <1>;
+
+						amx1_in2_ep: endpoint {
+							remote-endpoint = <&xbar_amx1_in2_ep>;
+						};
+					};
+
+					port@2 {
+						reg = <2>;
+
+						amx1_in3_ep: endpoint {
+							remote-endpoint = <&xbar_amx1_in3_ep>;
+						};
+					};
+
+					port@3 {
+						reg = <3>;
+
+						amx1_in4_ep: endpoint {
+							remote-endpoint = <&xbar_amx1_in4_ep>;
+						};
+					};
+
+					amx1_out_port: port@4 {
+						reg = <4>;
+
+						amx1_out_ep: endpoint {
+							remote-endpoint = <&xbar_amx1_out_ep>;
+						};
+					};
+				};
+			};
+
+			amx@702d3100 {
+				status = "okay";
+
+				ports {
+					#address-cells = <1>;
+					#size-cells = <0>;
+
+					port@0 {
+						reg = <0>;
+
+						amx2_in1_ep: endpoint {
+							remote-endpoint = <&xbar_amx2_in1_ep>;
+						};
+					};
+
+					port@1 {
+						reg = <1>;
+
+						amx2_in2_ep: endpoint {
+							remote-endpoint = <&xbar_amx2_in2_ep>;
+						};
+					};
+
+					amx2_in3_port: port@2 {
+						reg = <2>;
+
+						amx2_in3_ep: endpoint {
+							remote-endpoint = <&xbar_amx2_in3_ep>;
+						};
+					};
+
+					amx2_in4_port: port@3 {
+						reg = <3>;
+
+						amx2_in4_ep: endpoint {
+							remote-endpoint = <&xbar_amx2_in4_ep>;
+						};
+					};
+
+					amx2_out_port: port@4 {
+						reg = <4>;
+
+						amx2_out_ep: endpoint {
+							remote-endpoint = <&xbar_amx2_out_ep>;
+						};
+					};
+				};
+			};
+
+			adx@702d3800 {
+				status = "okay";
+
+				ports {
+					#address-cells = <1>;
+					#size-cells = <0>;
+
+					port@0 {
+						reg = <0>;
+
+						adx1_in_ep: endpoint {
+							remote-endpoint = <&xbar_adx1_in_ep>;
+						};
+					};
+
+					adx1_out1_port: port@1 {
+						reg = <1>;
+
+						adx1_out1_ep: endpoint {
+							remote-endpoint = <&xbar_adx1_out1_ep>;
+						};
+					};
+
+					adx1_out2_port: port@2 {
+						reg = <2>;
+
+						adx1_out2_ep: endpoint {
+							remote-endpoint = <&xbar_adx1_out2_ep>;
+						};
+					};
+
+					adx1_out3_port: port@3 {
+						reg = <3>;
+
+						adx1_out3_ep: endpoint {
+							remote-endpoint = <&xbar_adx1_out3_ep>;
+						};
+					};
+
+					adx1_out4_port: port@4 {
+						reg = <4>;
+
+						adx1_out4_ep: endpoint {
+							remote-endpoint = <&xbar_adx1_out4_ep>;
+						};
+					};
+				};
+			};
+
+			adx@702d3900 {
+				status = "okay";
+
+				ports {
+					#address-cells = <1>;
+					#size-cells = <0>;
+
+					port@0 {
+						reg = <0>;
+
+						adx2_in_ep: endpoint {
+							remote-endpoint = <&xbar_adx2_in_ep>;
+						};
+					};
+
+					adx2_out1_port: port@1 {
+						reg = <1>;
+
+						adx2_out1_ep: endpoint {
+							remote-endpoint = <&xbar_adx2_out1_ep>;
+						};
+					};
+
+					adx2_out2_port: port@2 {
+						reg = <2>;
+
+						adx2_out2_ep: endpoint {
+							remote-endpoint = <&xbar_adx2_out2_ep>;
+						};
+					};
+
+					adx2_out3_port: port@3 {
+						reg = <3>;
+
+						adx2_out3_ep: endpoint {
+							remote-endpoint = <&xbar_adx2_out3_ep>;
+						};
+					};
+
+					adx2_out4_port: port@4 {
+						reg = <4>;
+
+						adx2_out4_ep: endpoint {
+							remote-endpoint = <&xbar_adx2_out4_ep>;
+						};
+					};
+				};
+			};
+
+			amixer@702dbb00 {
+				status = "okay";
+
+				ports {
+					#address-cells = <1>;
+					#size-cells = <0>;
+
+					port@0 {
+						reg = <0x0>;
+
+						mixer_in1_ep: endpoint {
+							remote-endpoint = <&xbar_mixer_in1_ep>;
+						};
+					};
+
+					port@1 {
+						reg = <0x1>;
+
+						mixer_in2_ep: endpoint {
+							remote-endpoint = <&xbar_mixer_in2_ep>;
+						};
+					};
+
+					port@2 {
+						reg = <0x2>;
+
+						mixer_in3_ep: endpoint {
+							remote-endpoint = <&xbar_mixer_in3_ep>;
+						};
+					};
+
+					port@3 {
+						reg = <0x3>;
+
+						mixer_in4_ep: endpoint {
+							remote-endpoint = <&xbar_mixer_in4_ep>;
+						};
+					};
+
+					port@4 {
+						reg = <0x4>;
+
+						mixer_in5_ep: endpoint {
+							remote-endpoint = <&xbar_mixer_in5_ep>;
+						};
+					};
+
+					port@5 {
+						reg = <0x5>;
+
+						mixer_in6_ep: endpoint {
+							remote-endpoint = <&xbar_mixer_in6_ep>;
+						};
+					};
+
+					port@6 {
+						reg = <0x6>;
+
+						mixer_in7_ep: endpoint {
+							remote-endpoint = <&xbar_mixer_in7_ep>;
+						};
+					};
+
+					port@7 {
+						reg = <0x7>;
+
+						mixer_in8_ep: endpoint {
+							remote-endpoint = <&xbar_mixer_in8_ep>;
+						};
+					};
+
+					port@8 {
+						reg = <0x8>;
+
+						mixer_in9_ep: endpoint {
+							remote-endpoint = <&xbar_mixer_in9_ep>;
+						};
+					};
+
+					port@9 {
+						reg = <0x9>;
+
+						mixer_in10_ep: endpoint {
+							remote-endpoint = <&xbar_mixer_in10_ep>;
+						};
+					};
+
+					mixer_out1_port: port@a {
+						reg = <0xa>;
+
+						mixer_out1_ep: endpoint {
+							remote-endpoint = <&xbar_mixer_out1_ep>;
+						};
+					};
+
+					mixer_out2_port: port@b {
+						reg = <0xb>;
+
+						mixer_out2_ep: endpoint {
+							remote-endpoint = <&xbar_mixer_out2_ep>;
+						};
+					};
+
+					mixer_out3_port: port@c {
+						reg = <0xc>;
+
+						mixer_out3_ep: endpoint {
+							remote-endpoint = <&xbar_mixer_out3_ep>;
+						};
+					};
+
+					mixer_out4_port: port@d {
+						reg = <0xd>;
+
+						mixer_out4_ep: endpoint {
+							remote-endpoint = <&xbar_mixer_out4_ep>;
+						};
+					};
+
+					mixer_out5_port: port@e {
+						reg = <0xe>;
+
+						mixer_out5_ep: endpoint {
+							remote-endpoint = <&xbar_mixer_out5_ep>;
+						};
+					};
+				};
+			};
+
 			ports {
 				xbar_i2s3_port: port@c {
 					reg = <0xc>;
@@ -778,6 +1253,382 @@
 						remote-endpoint = <&dmic2_cif_ep>;
 					};
 				};
+
+				xbar_sfc1_in_port: port@12 {
+					reg = <0x12>;
+
+					xbar_sfc1_in_ep: endpoint {
+						remote-endpoint = <&sfc1_cif_in_ep>;
+					};
+				};
+
+				port@13 {
+					reg = <0x13>;
+
+					xbar_sfc1_out_ep: endpoint {
+						remote-endpoint = <&sfc1_cif_out_ep>;
+					};
+				};
+
+				xbar_sfc2_in_port: port@14 {
+					reg = <0x14>;
+
+					xbar_sfc2_in_ep: endpoint {
+						remote-endpoint = <&sfc2_cif_in_ep>;
+					};
+				};
+
+				port@15 {
+					reg = <0x15>;
+
+					xbar_sfc2_out_ep: endpoint {
+						remote-endpoint = <&sfc2_cif_out_ep>;
+					};
+				};
+
+				xbar_sfc3_in_port: port@16 {
+					reg = <0x16>;
+
+					xbar_sfc3_in_ep: endpoint {
+						remote-endpoint = <&sfc3_cif_in_ep>;
+					};
+				};
+
+				port@17 {
+					reg = <0x17>;
+
+					xbar_sfc3_out_ep: endpoint {
+						remote-endpoint = <&sfc3_cif_out_ep>;
+					};
+				};
+
+				xbar_sfc4_in_port: port@18 {
+					reg = <0x18>;
+
+					xbar_sfc4_in_ep: endpoint {
+						remote-endpoint = <&sfc4_cif_in_ep>;
+					};
+				};
+
+				port@19 {
+					reg = <0x19>;
+
+					xbar_sfc4_out_ep: endpoint {
+						remote-endpoint = <&sfc4_cif_out_ep>;
+					};
+				};
+
+				xbar_mvc1_in_port: port@1a {
+					reg = <0x1a>;
+
+					xbar_mvc1_in_ep: endpoint {
+						remote-endpoint = <&mvc1_cif_in_ep>;
+					};
+				};
+
+				port@1b {
+					reg = <0x1b>;
+
+					xbar_mvc1_out_ep: endpoint {
+						remote-endpoint = <&mvc1_cif_out_ep>;
+					};
+				};
+
+				xbar_mvc2_in_port: port@1c {
+					reg = <0x1c>;
+
+					xbar_mvc2_in_ep: endpoint {
+						remote-endpoint = <&mvc2_cif_in_ep>;
+					};
+				};
+
+				port@1d {
+					reg = <0x1d>;
+
+					xbar_mvc2_out_ep: endpoint {
+						remote-endpoint = <&mvc2_cif_out_ep>;
+					};
+				};
+
+				xbar_amx1_in1_port: port@1e {
+					reg = <0x1e>;
+
+					xbar_amx1_in1_ep: endpoint {
+						remote-endpoint = <&amx1_in1_ep>;
+					};
+				};
+
+				xbar_amx1_in2_port: port@1f {
+					reg = <0x1f>;
+
+					xbar_amx1_in2_ep: endpoint {
+						remote-endpoint = <&amx1_in2_ep>;
+					};
+				};
+
+				xbar_amx1_in3_port: port@20 {
+					reg = <0x20>;
+
+					xbar_amx1_in3_ep: endpoint {
+						remote-endpoint = <&amx1_in3_ep>;
+					};
+				};
+
+				xbar_amx1_in4_port: port@21 {
+					reg = <0x21>;
+
+					xbar_amx1_in4_ep: endpoint {
+						remote-endpoint = <&amx1_in4_ep>;
+					};
+				};
+
+				port@22 {
+					reg = <0x22>;
+
+					xbar_amx1_out_ep: endpoint {
+						remote-endpoint = <&amx1_out_ep>;
+					};
+				};
+
+				xbar_amx2_in1_port: port@23 {
+					reg = <0x23>;
+
+					xbar_amx2_in1_ep: endpoint {
+						remote-endpoint = <&amx2_in1_ep>;
+					};
+				};
+
+				xbar_amx2_in2_port: port@24 {
+					reg = <0x24>;
+
+					xbar_amx2_in2_ep: endpoint {
+						remote-endpoint = <&amx2_in2_ep>;
+					};
+				};
+
+				xbar_amx2_in3_port: port@25 {
+					reg = <0x25>;
+
+					xbar_amx2_in3_ep: endpoint {
+						remote-endpoint = <&amx2_in3_ep>;
+					};
+				};
+
+				xbar_amx2_in4_port: port@26 {
+					reg = <0x26>;
+
+					xbar_amx2_in4_ep: endpoint {
+						remote-endpoint = <&amx2_in4_ep>;
+					};
+				};
+
+				port@27 {
+					reg = <0x27>;
+
+					xbar_amx2_out_ep: endpoint {
+						remote-endpoint = <&amx2_out_ep>;
+					};
+				};
+
+				xbar_adx1_in_port: port@28 {
+					reg = <0x28>;
+
+					xbar_adx1_in_ep: endpoint {
+						remote-endpoint = <&adx1_in_ep>;
+					};
+				};
+
+				port@29 {
+					reg = <0x29>;
+
+					xbar_adx1_out1_ep: endpoint {
+						remote-endpoint = <&adx1_out1_ep>;
+					};
+				};
+
+				port@2a {
+					reg = <0x2a>;
+
+					xbar_adx1_out2_ep: endpoint {
+						remote-endpoint = <&adx1_out2_ep>;
+					};
+				};
+
+				port@2b {
+					reg = <0x2b>;
+
+					xbar_adx1_out3_ep: endpoint {
+						remote-endpoint = <&adx1_out3_ep>;
+					};
+				};
+
+				port@2c {
+					reg = <0x2c>;
+
+					xbar_adx1_out4_ep: endpoint {
+						remote-endpoint = <&adx1_out4_ep>;
+					};
+				};
+
+				xbar_adx2_in_port: port@2d {
+					reg = <0x2d>;
+
+					xbar_adx2_in_ep: endpoint {
+						remote-endpoint = <&adx2_in_ep>;
+					};
+				};
+
+				port@2e {
+					reg = <0x2e>;
+
+					xbar_adx2_out1_ep: endpoint {
+						remote-endpoint = <&adx2_out1_ep>;
+					};
+				};
+
+				port@2f {
+					reg = <0x2f>;
+
+					xbar_adx2_out2_ep: endpoint {
+						remote-endpoint = <&adx2_out2_ep>;
+					};
+				};
+
+				port@30 {
+					reg = <0x30>;
+
+					xbar_adx2_out3_ep: endpoint {
+						remote-endpoint = <&adx2_out3_ep>;
+					};
+				};
+
+				port@31 {
+					reg = <0x31>;
+
+					xbar_adx2_out4_ep: endpoint {
+						remote-endpoint = <&adx2_out4_ep>;
+					};
+				};
+
+				xbar_mixer_in1_port: port@32 {
+					reg = <0x32>;
+
+					xbar_mixer_in1_ep: endpoint {
+						remote-endpoint = <&mixer_in1_ep>;
+					};
+				};
+
+				xbar_mixer_in2_port: port@33 {
+					reg = <0x33>;
+
+					xbar_mixer_in2_ep: endpoint {
+						remote-endpoint = <&mixer_in2_ep>;
+					};
+				};
+
+				xbar_mixer_in3_port: port@34 {
+					reg = <0x34>;
+
+					xbar_mixer_in3_ep: endpoint {
+						remote-endpoint = <&mixer_in3_ep>;
+					};
+				};
+
+				xbar_mixer_in4_port: port@35 {
+					reg = <0x35>;
+
+					xbar_mixer_in4_ep: endpoint {
+						remote-endpoint = <&mixer_in4_ep>;
+					};
+				};
+
+				xbar_mixer_in5_port: port@36 {
+					reg = <0x36>;
+
+					xbar_mixer_in5_ep: endpoint {
+						remote-endpoint = <&mixer_in5_ep>;
+					};
+				};
+
+				xbar_mixer_in6_port: port@37 {
+					reg = <0x37>;
+
+					xbar_mixer_in6_ep: endpoint {
+						remote-endpoint = <&mixer_in6_ep>;
+					};
+				};
+
+				xbar_mixer_in7_port: port@38 {
+					reg = <0x38>;
+
+					xbar_mixer_in7_ep: endpoint {
+						remote-endpoint = <&mixer_in7_ep>;
+					};
+				};
+
+				xbar_mixer_in8_port: port@39 {
+					reg = <0x39>;
+
+					xbar_mixer_in8_ep: endpoint {
+						remote-endpoint = <&mixer_in8_ep>;
+					};
+				};
+
+				xbar_mixer_in9_port: port@3a {
+					reg = <0x3a>;
+
+					xbar_mixer_in9_ep: endpoint {
+						remote-endpoint = <&mixer_in9_ep>;
+					};
+				};
+
+				xbar_mixer_in10_port: port@3b {
+					reg = <0x3b>;
+
+					xbar_mixer_in10_ep: endpoint {
+						remote-endpoint = <&mixer_in10_ep>;
+					};
+				};
+
+				port@3c {
+					reg = <0x3c>;
+
+					xbar_mixer_out1_ep: endpoint {
+						remote-endpoint = <&mixer_out1_ep>;
+					};
+				};
+
+				port@3d {
+					reg = <0x3d>;
+
+					xbar_mixer_out2_ep: endpoint {
+						remote-endpoint = <&mixer_out2_ep>;
+					};
+				};
+
+				port@3e {
+					reg = <0x3e>;
+
+					xbar_mixer_out3_ep: endpoint {
+						remote-endpoint = <&mixer_out3_ep>;
+					};
+				};
+
+				port@3f {
+					reg = <0x3f>;
+
+					xbar_mixer_out4_ep: endpoint {
+						remote-endpoint = <&mixer_out4_ep>;
+					};
+				};
+
+				port@40 {
+					reg = <0x40>;
+
+					xbar_mixer_out5_ep: endpoint {
+						remote-endpoint = <&mixer_out5_ep>;
+					};
+				};
 			};
 		};
 	};
@@ -1039,6 +1890,31 @@
 		       /* Router */
 		       <&xbar_i2s3_port>, <&xbar_i2s4_port>,
 		       <&xbar_dmic1_port>, <&xbar_dmic2_port>,
+		       <&xbar_sfc1_in_port>, <&xbar_sfc2_in_port>,
+		       <&xbar_sfc3_in_port>, <&xbar_sfc4_in_port>,
+		       <&xbar_mvc1_in_port>, <&xbar_mvc2_in_port>,
+		       <&xbar_amx1_in1_port>, <&xbar_amx1_in2_port>,
+		       <&xbar_amx1_in3_port>, <&xbar_amx1_in4_port>,
+		       <&xbar_amx2_in1_port>, <&xbar_amx2_in2_port>,
+		       <&xbar_amx2_in3_port>, <&xbar_amx2_in4_port>,
+		       <&xbar_adx1_in_port>, <&xbar_adx2_in_port>,
+		       <&xbar_mixer_in1_port>, <&xbar_mixer_in2_port>,
+		       <&xbar_mixer_in3_port>, <&xbar_mixer_in4_port>,
+		       <&xbar_mixer_in5_port>, <&xbar_mixer_in6_port>,
+		       <&xbar_mixer_in7_port>, <&xbar_mixer_in8_port>,
+		       <&xbar_mixer_in9_port>, <&xbar_mixer_in10_port>,
+		       /* HW accelerators */
+		       <&sfc1_out_port>, <&sfc2_out_port>,
+		       <&sfc3_out_port>, <&sfc4_out_port>,
+		       <&mvc1_out_port>, <&mvc2_out_port>,
+		       <&amx1_out_port>, <&amx2_out_port>,
+		       <&adx1_out1_port>, <&adx1_out2_port>,
+		       <&adx1_out3_port>, <&adx1_out4_port>,
+		       <&adx2_out1_port>, <&adx2_out2_port>,
+		       <&adx2_out3_port>, <&adx2_out4_port>,
+		       <&mixer_out1_port>, <&mixer_out2_port>,
+		       <&mixer_out3_port>, <&mixer_out4_port>,
+		       <&mixer_out5_port>,
 		       /* I/O DAP Ports */
 		       <&i2s3_port>, <&i2s4_port>,
 		       <&dmic1_port>, <&dmic2_port>;
diff --git a/arch/arm64/boot/dts/nvidia/tegra210.dtsi b/arch/arm64/boot/dts/nvidia/tegra210.dtsi
index 26b3f98a211c..ccdc0dec4e59 100644
--- a/arch/arm64/boot/dts/nvidia/tegra210.dtsi
+++ b/arch/arm64/boot/dts/nvidia/tegra210.dtsi
@@ -1641,6 +1641,83 @@
 				status = "disabled";
 			};
 
+			tegra_sfc1: sfc@702d2000 {
+				compatible = "nvidia,tegra210-sfc";
+				reg = <0x702d2000 0x200>;
+				sound-name-prefix = "SFC1";
+				status = "disabled";
+			};
+
+			tegra_sfc2: sfc@702d2200 {
+				compatible = "nvidia,tegra210-sfc";
+				reg = <0x702d2200 0x200>;
+				sound-name-prefix = "SFC2";
+				status = "disabled";
+			};
+
+			tegra_sfc3: sfc@702d2400 {
+				compatible = "nvidia,tegra210-sfc";
+				reg = <0x702d2400 0x200>;
+				sound-name-prefix = "SFC3";
+				status = "disabled";
+			};
+
+			tegra_sfc4: sfc@702d2600 {
+				compatible = "nvidia,tegra210-sfc";
+				reg = <0x702d2600 0x200>;
+				sound-name-prefix = "SFC4";
+				status = "disabled";
+			};
+
+			tegra_mvc1: mvc@702da000 {
+				compatible = "nvidia,tegra210-mvc";
+				reg = <0x702da000 0x200>;
+				sound-name-prefix = "MVC1";
+				status = "disabled";
+			};
+
+			tegra_mvc2: mvc@702da200 {
+				compatible = "nvidia,tegra210-mvc";
+				reg = <0x702da200 0x200>;
+				sound-name-prefix = "MVC2";
+				status = "disabled";
+			};
+
+			tegra_amx1: amx@702d3000 {
+				compatible = "nvidia,tegra210-amx";
+				reg = <0x702d3000 0x100>;
+				sound-name-prefix = "AMX1";
+				status = "disabled";
+			};
+
+			tegra_amx2: amx@702d3100 {
+				compatible = "nvidia,tegra210-amx";
+				reg = <0x702d3100 0x100>;
+				sound-name-prefix = "AMX2";
+				status = "disabled";
+			};
+
+			tegra_adx1: adx@702d3800 {
+				compatible = "nvidia,tegra210-adx";
+				reg = <0x702d3800 0x100>;
+				sound-name-prefix = "ADX1";
+				status = "disabled";
+			};
+
+			tegra_adx2: adx@702d3900 {
+				compatible = "nvidia,tegra210-adx";
+				reg = <0x702d3900 0x100>;
+				sound-name-prefix = "ADX2";
+				status = "disabled";
+			};
+
+			tegra_amixer: amixer@702dbb00 {
+				compatible = "nvidia,tegra210-amixer";
+				reg = <0x702dbb00 0x800>;
+				sound-name-prefix = "MIXER1";
+				status = "disabled";
+			};
+
 			ports {
 				#address-cells = <1>;
 				#size-cells = <0>;
@@ -1743,7 +1820,7 @@
 	};
 
 	usb@7d000000 {
-		compatible = "nvidia,tegra210-ehci", "nvidia,tegra30-ehci", "usb-ehci";
+		compatible = "nvidia,tegra210-ehci", "nvidia,tegra30-ehci";
 		reg = <0x0 0x7d000000 0x0 0x4000>;
 		interrupts = <GIC_SPI 20 IRQ_TYPE_LEVEL_HIGH>;
 		phy_type = "utmi";
@@ -1781,7 +1858,7 @@
 	};
 
 	usb@7d004000 {
-		compatible = "nvidia,tegra210-ehci", "nvidia,tegra30-ehci", "usb-ehci";
+		compatible = "nvidia,tegra210-ehci", "nvidia,tegra30-ehci";
 		reg = <0x0 0x7d004000 0x0 0x4000>;
 		interrupts = <GIC_SPI 21 IRQ_TYPE_LEVEL_HIGH>;
 		phy_type = "utmi";
diff --git a/arch/arm64/boot/dts/qcom/Makefile b/arch/arm64/boot/dts/qcom/Makefile
index 70516508be56..6b816eb33309 100644
--- a/arch/arm64/boot/dts/qcom/Makefile
+++ b/arch/arm64/boot/dts/qcom/Makefile
@@ -15,6 +15,7 @@ dtb-$(CONFIG_ARCH_QCOM)	+= msm8916-longcheer-l8910.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= msm8916-mtp.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= msm8916-samsung-a3u-eur.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= msm8916-samsung-a5u-eur.dtb
+dtb-$(CONFIG_ARCH_QCOM)	+= msm8916-samsung-serranove.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= msm8916-wingtech-wt88047.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= msm8992-bullhead-rev-101.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= msm8992-msft-lumia-octagon-talkman.dtb
@@ -33,12 +34,18 @@ dtb-$(CONFIG_ARCH_QCOM)	+= msm8996-pmi8996-sony-xperia-tone-keyaki.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= msm8996-sony-xperia-tone-dora.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= msm8996-sony-xperia-tone-kagura.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= msm8996-sony-xperia-tone-keyaki.dtb
+dtb-$(CONFIG_ARCH_QCOM)	+= msm8996-xiaomi-gemini.dtb
+dtb-$(CONFIG_ARCH_QCOM)	+= msm8996-xiaomi-scorpio.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= msm8998-asus-novago-tp370ql.dtb
+dtb-$(CONFIG_ARCH_QCOM)	+= msm8998-fxtec-pro1.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= msm8998-hp-envy-x2.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= msm8998-lenovo-miix-630.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= msm8998-mtp.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= msm8998-oneplus-cheeseburger.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= msm8998-oneplus-dumpling.dtb
+dtb-$(CONFIG_ARCH_QCOM)	+= msm8998-sony-xperia-yoshino-lilac.dtb
+dtb-$(CONFIG_ARCH_QCOM)	+= msm8998-sony-xperia-yoshino-maple.dtb
+dtb-$(CONFIG_ARCH_QCOM)	+= msm8998-sony-xperia-yoshino-poplar.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= qcs404-evb-1000.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= qcs404-evb-4000.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= qrb5165-rb5.dtb
@@ -48,6 +55,8 @@ dtb-$(CONFIG_ARCH_QCOM)	+= sc7180-trogdor-coachz-r1.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= sc7180-trogdor-coachz-r1-lte.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= sc7180-trogdor-coachz-r3.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= sc7180-trogdor-coachz-r3-lte.dtb
+dtb-$(CONFIG_ARCH_QCOM)	+= sc7180-trogdor-homestar-r2.dtb
+dtb-$(CONFIG_ARCH_QCOM)	+= sc7180-trogdor-homestar-r3.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= sc7180-trogdor-lazor-r0.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= sc7180-trogdor-lazor-r1.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= sc7180-trogdor-lazor-r1-kb.dtb
@@ -66,6 +75,7 @@ dtb-$(CONFIG_ARCH_QCOM)	+= sc7180-trogdor-pompom-r3.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= sc7180-trogdor-pompom-r3-lte.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= sc7180-trogdor-r1.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= sc7180-trogdor-r1-lte.dtb
+dtb-$(CONFIG_ARCH_QCOM)	+= sc7280-herobrine.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= sc7280-idp.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= sc7280-idp2.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= sdm630-sony-xperia-ganges-kirin.dtb
@@ -84,6 +94,8 @@ dtb-$(CONFIG_ARCH_QCOM)	+= sdm845-oneplus-fajita.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= sdm845-xiaomi-beryllium.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= sdm850-lenovo-yoga-c630.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= sm6125-sony-xperia-seine-pdx201.dtb
+dtb-$(CONFIG_ARCH_QCOM)	+= sm6350-sony-xperia-lena-pdx213.dtb
+dtb-$(CONFIG_ARCH_QCOM)	+= sm7225-fairphone-fp4.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= sm8150-hdk.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= sm8150-microsoft-surface-duo.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= sm8150-mtp.dtb
diff --git a/arch/arm64/boot/dts/qcom/apq8016-sbc.dts b/arch/arm64/boot/dts/qcom/apq8016-sbc.dts
index f3c0dbfd0a23..a5320d6d30e7 100644
--- a/arch/arm64/boot/dts/qcom/apq8016-sbc.dts
+++ b/arch/arm64/boot/dts/qcom/apq8016-sbc.dts
@@ -5,9 +5,839 @@
 
 /dts-v1/;
 
-#include "apq8016-sbc.dtsi"
+#include "msm8916-pm8916.dtsi"
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/pinctrl/qcom,pmic-gpio.h>
+#include <dt-bindings/pinctrl/qcom,pmic-mpp.h>
+#include <dt-bindings/sound/apq8016-lpass.h>
 
 / {
 	model = "Qualcomm Technologies, Inc. APQ 8016 SBC";
 	compatible = "qcom,apq8016-sbc", "qcom,apq8016";
+
+	aliases {
+		serial0 = &blsp1_uart2;
+		serial1 = &blsp1_uart1;
+		usid0 = &pm8916_0;
+		i2c0	= &blsp_i2c2;
+		i2c1	= &blsp_i2c6;
+		i2c3	= &blsp_i2c4;
+		spi0	= &blsp_spi5;
+		spi1	= &blsp_spi3;
+	};
+
+	chosen {
+		stdout-path = "serial0";
+	};
+
+	camera_vdddo_1v8: camera-vdddo-1v8 {
+		compatible = "regulator-fixed";
+		regulator-name = "camera_vdddo";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+		regulator-always-on;
+	};
+
+	camera_vdda_2v8: camera-vdda-2v8 {
+		compatible = "regulator-fixed";
+		regulator-name = "camera_vdda";
+		regulator-min-microvolt = <2800000>;
+		regulator-max-microvolt = <2800000>;
+		regulator-always-on;
+	};
+
+	camera_vddd_1v5: camera-vddd-1v5 {
+		compatible = "regulator-fixed";
+		regulator-name = "camera_vddd";
+		regulator-min-microvolt = <1500000>;
+		regulator-max-microvolt = <1500000>;
+		regulator-always-on;
+	};
+
+	reserved-memory {
+		ramoops@bff00000 {
+			compatible = "ramoops";
+			reg = <0x0 0xbff00000 0x0 0x100000>;
+
+			record-size = <0x20000>;
+			console-size = <0x20000>;
+			ftrace-size = <0x20000>;
+		};
+	};
+
+	usb2513 {
+		compatible = "smsc,usb3503";
+		reset-gpios = <&pm8916_gpios 3 GPIO_ACTIVE_LOW>;
+		initial-mode = <1>;
+	};
+
+	usb_id: usb-id {
+		compatible = "linux,extcon-usb-gpio";
+		id-gpio = <&msmgpio 121 GPIO_ACTIVE_HIGH>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&usb_id_default>;
+	};
+
+	hdmi-out {
+		compatible = "hdmi-connector";
+		type = "a";
+
+		port {
+			hdmi_con: endpoint {
+				remote-endpoint = <&adv7533_out>;
+			};
+		};
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+		#address-cells = <1>;
+		#size-cells = <0>;
+		autorepeat;
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&msm_key_volp_n_default>;
+
+		button@0 {
+			label = "Volume Up";
+			linux,code = <KEY_VOLUMEUP>;
+			gpios = <&msmgpio 107 GPIO_ACTIVE_LOW>;
+		};
+	};
+
+	leds {
+		pinctrl-names = "default";
+		pinctrl-0 = <&msmgpio_leds>,
+			    <&pm8916_gpios_leds>,
+			    <&pm8916_mpps_leds>;
+
+		compatible = "gpio-leds";
+
+		led@1 {
+			label = "apq8016-sbc:green:user1";
+			gpios = <&msmgpio 21 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "heartbeat";
+			default-state = "off";
+		};
+
+		led@2 {
+			label = "apq8016-sbc:green:user2";
+			gpios = <&msmgpio 120 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "mmc0";
+			default-state = "off";
+		};
+
+		led@3 {
+			label = "apq8016-sbc:green:user3";
+			gpios = <&pm8916_gpios 1 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "mmc1";
+			default-state = "off";
+		};
+
+		led@4 {
+			label = "apq8016-sbc:green:user4";
+			gpios = <&pm8916_gpios 2 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "none";
+			panic-indicator;
+			default-state = "off";
+		};
+
+		led@5 {
+			label = "apq8016-sbc:yellow:wlan";
+			gpios = <&pm8916_mpps 2 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "phy0tx";
+			default-state = "off";
+		};
+
+		led@6 {
+			label = "apq8016-sbc:blue:bt";
+			gpios = <&pm8916_mpps 3 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "bluetooth-power";
+			default-state = "off";
+		};
+	};
+};
+
+&blsp_dma {
+	status = "okay";
+};
+
+&blsp_i2c2 {
+	/* On Low speed expansion */
+	status = "okay";
+	label = "LS-I2C0";
+};
+
+&blsp_i2c4 {
+	/* On High speed expansion */
+	status = "okay";
+	label = "HS-I2C2";
+
+	adv_bridge: bridge@39 {
+		status = "okay";
+
+		compatible = "adi,adv7533";
+		reg = <0x39>;
+
+		interrupt-parent = <&msmgpio>;
+		interrupts = <31 IRQ_TYPE_EDGE_FALLING>;
+
+		adi,dsi-lanes = <4>;
+		clocks = <&rpmcc RPM_SMD_BB_CLK2>;
+		clock-names = "cec";
+
+		pd-gpios = <&msmgpio 32 GPIO_ACTIVE_HIGH>;
+
+		avdd-supply = <&pm8916_l6>;
+		v1p2-supply = <&pm8916_l6>;
+		v3p3-supply = <&pm8916_l17>;
+
+		pinctrl-names = "default","sleep";
+		pinctrl-0 = <&adv7533_int_active &adv7533_switch_active>;
+		pinctrl-1 = <&adv7533_int_suspend &adv7533_switch_suspend>;
+		#sound-dai-cells = <1>;
+
+		ports {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			port@0 {
+				reg = <0>;
+				adv7533_in: endpoint {
+					remote-endpoint = <&dsi0_out>;
+				};
+			};
+
+			port@1 {
+				reg = <1>;
+				adv7533_out: endpoint {
+					remote-endpoint = <&hdmi_con>;
+				};
+			};
+		};
+	};
+};
+
+&blsp_i2c6 {
+	/* On Low speed expansion */
+	status = "okay";
+	label = "LS-I2C1";
+};
+
+&blsp_spi3 {
+	/* On High speed expansion */
+	status = "okay";
+	label = "HS-SPI1";
+};
+
+&blsp_spi5 {
+	/* On Low speed expansion */
+	status = "okay";
+	label = "LS-SPI0";
+};
+
+&blsp1_uart1 {
+	status = "okay";
+	label = "LS-UART0";
+};
+
+&blsp1_uart2 {
+	status = "okay";
+	label = "LS-UART1";
+};
+
+&camss {
+	status = "okay";
+	ports {
+		port@0 {
+			reg = <0>;
+			csiphy0_ep: endpoint {
+				clock-lanes = <1>;
+				data-lanes = <0 2>;
+				remote-endpoint = <&ov5640_ep>;
+				status = "okay";
+			};
+		};
+	};
+};
+
+&cci {
+	status = "okay";
+};
+
+&cci_i2c0 {
+	camera_rear@3b {
+		compatible = "ovti,ov5640";
+		reg = <0x3b>;
+
+		enable-gpios = <&msmgpio 34 GPIO_ACTIVE_HIGH>;
+		reset-gpios = <&msmgpio 35 GPIO_ACTIVE_LOW>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&camera_rear_default>;
+
+		clocks = <&gcc GCC_CAMSS_MCLK0_CLK>;
+		clock-names = "xclk";
+		clock-frequency = <23880000>;
+
+		vdddo-supply = <&camera_vdddo_1v8>;
+		vdda-supply = <&camera_vdda_2v8>;
+		vddd-supply = <&camera_vddd_1v5>;
+
+		/* No camera mezzanine by default */
+		status = "disabled";
+
+		port {
+			ov5640_ep: endpoint {
+				clock-lanes = <1>;
+				data-lanes = <0 2>;
+				remote-endpoint = <&csiphy0_ep>;
+			};
+		};
+	};
+};
+
+&dsi0_out {
+	data-lanes = <0 1 2 3>;
+	remote-endpoint = <&adv7533_in>;
+};
+
+&lpass {
+	status = "okay";
+};
+
+&mdss {
+	status = "okay";
+};
+
+&mpss {
+	status = "okay";
+
+	firmware-name = "qcom/apq8016/mba.mbn", "qcom/apq8016/modem.mbn";
+};
+
+&pm8916_resin {
+	status = "okay";
+	linux,code = <KEY_VOLUMEDOWN>;
+};
+
+&pronto {
+	status = "okay";
+
+	firmware-name = "qcom/apq8016/wcnss.mbn";
+};
+
+&sdhc_1 {
+	status = "okay";
+
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&sdc1_clk_on &sdc1_cmd_on &sdc1_data_on>;
+	pinctrl-1 = <&sdc1_clk_off &sdc1_cmd_off &sdc1_data_off>;
+};
+
+&sdhc_2 {
+	status = "okay";
+
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&sdc2_clk_on &sdc2_cmd_on &sdc2_data_on &sdc2_cd_on>;
+	pinctrl-1 = <&sdc2_clk_off &sdc2_cmd_off &sdc2_data_off &sdc2_cd_off>;
+
+	cd-gpios = <&msmgpio 38 GPIO_ACTIVE_LOW>;
+};
+
+&sound {
+	status = "okay";
+
+	pinctrl-0 = <&cdc_pdm_lines_act &ext_sec_tlmm_lines_act &ext_mclk_tlmm_lines_act>;
+	pinctrl-1 = <&cdc_pdm_lines_sus &ext_sec_tlmm_lines_sus &ext_mclk_tlmm_lines_sus>;
+	pinctrl-names = "default", "sleep";
+	qcom,model = "DB410c";
+	qcom,audio-routing =
+		"AMIC2", "MIC BIAS Internal2",
+		"AMIC3", "MIC BIAS External1";
+
+	external-dai-link@0 {
+		link-name = "ADV7533";
+		cpu {
+			sound-dai = <&lpass MI2S_QUATERNARY>;
+		};
+		codec {
+			sound-dai = <&adv_bridge 0>;
+		};
+	};
+
+	internal-codec-playback-dai-link@0 {
+		link-name = "WCD";
+		cpu {
+			sound-dai = <&lpass MI2S_PRIMARY>;
+		};
+		codec {
+			sound-dai = <&lpass_codec 0>, <&wcd_codec 0>;
+		};
+	};
+
+	internal-codec-capture-dai-link@0 {
+		link-name = "WCD-Capture";
+		cpu {
+			sound-dai = <&lpass MI2S_TERTIARY>;
+		};
+		codec {
+			sound-dai = <&lpass_codec 1>, <&wcd_codec 1>;
+		};
+	};
+};
+
+&usb {
+	status = "okay";
+	extcon = <&usb_id>, <&usb_id>;
+
+	pinctrl-names = "default", "device";
+	pinctrl-0 = <&usb_sw_sel_pm &usb_hub_reset_pm>;
+	pinctrl-1 = <&usb_sw_sel_pm_device &usb_hub_reset_pm_device>;
+};
+
+&usb_hs_phy {
+	extcon = <&usb_id>;
+};
+
+&wcd_codec {
+	clocks = <&gcc GCC_CODEC_DIGCODEC_CLK>;
+	clock-names = "mclk";
+	qcom,mbhc-vthreshold-low = <75 150 237 450 500>;
+	qcom,mbhc-vthreshold-high = <75 150 237 450 500>;
+};
+
+&wcnss_ctrl {
+	firmware-name = "qcom/apq8016/WCNSS_qcom_wlan_nv_sbc.bin";
+};
+
+/* Enable CoreSight */
+&cti0 { status = "okay"; };
+&cti1 { status = "okay"; };
+&cti12 { status = "okay"; };
+&cti13 { status = "okay"; };
+&cti14 { status = "okay"; };
+&cti15 { status = "okay"; };
+&debug0 { status = "okay"; };
+&debug1 { status = "okay"; };
+&debug2 { status = "okay"; };
+&debug3 { status = "okay"; };
+&etf { status = "okay"; };
+&etm0 { status = "okay"; };
+&etm1 { status = "okay"; };
+&etm2 { status = "okay"; };
+&etm3 { status = "okay"; };
+&etr { status = "okay"; };
+&funnel0 { status = "okay"; };
+&funnel1 { status = "okay"; };
+&replicator { status = "okay"; };
+&stm { status = "okay"; };
+&tpiu { status = "okay"; };
+
+&smd_rpm_regulators {
+	vdd_l1_l2_l3-supply = <&pm8916_s3>;
+	vdd_l4_l5_l6-supply = <&pm8916_s4>;
+	vdd_l7-supply = <&pm8916_s4>;
+
+	s3 {
+		regulator-min-microvolt = <375000>;
+		regulator-max-microvolt = <1562000>;
+	};
+
+	s4 {
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+
+		regulator-always-on;
+		regulator-boot-on;
+	};
+
+	l1 {
+		regulator-min-microvolt = <375000>;
+		regulator-max-microvolt = <1525000>;
+	};
+
+	l2 {
+		regulator-min-microvolt = <1200000>;
+		regulator-max-microvolt = <1200000>;
+	};
+
+	l4 {
+		regulator-min-microvolt = <1750000>;
+		regulator-max-microvolt = <3337000>;
+	};
+
+	l5 {
+		regulator-min-microvolt = <1750000>;
+		regulator-max-microvolt = <3337000>;
+	};
+
+	l6 {
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+	};
+
+	l7 {
+		regulator-min-microvolt = <1750000>;
+		regulator-max-microvolt = <3337000>;
+	};
+
+	l8 {
+		regulator-min-microvolt = <1750000>;
+		regulator-max-microvolt = <3337000>;
+	};
+
+	l9 {
+		regulator-min-microvolt = <1750000>;
+		regulator-max-microvolt = <3337000>;
+	};
+
+	l10 {
+		regulator-min-microvolt = <1750000>;
+		regulator-max-microvolt = <3337000>;
+	};
+
+	l11 {
+		regulator-min-microvolt = <1750000>;
+		regulator-max-microvolt = <3337000>;
+		regulator-allow-set-load;
+		regulator-system-load = <200000>;
+	};
+
+	l12 {
+		regulator-min-microvolt = <1750000>;
+		regulator-max-microvolt = <3337000>;
+	};
+
+	l13 {
+		regulator-min-microvolt = <1750000>;
+		regulator-max-microvolt = <3337000>;
+	};
+
+	l14 {
+		regulator-min-microvolt = <1750000>;
+		regulator-max-microvolt = <3337000>;
+	};
+
+	/**
+	 * 1.8v required on LS expansion
+	 * for mezzanine boards
+	 */
+	l15 {
+		regulator-min-microvolt = <1750000>;
+		regulator-max-microvolt = <3337000>;
+		regulator-always-on;
+	};
+
+	l16 {
+		regulator-min-microvolt = <1750000>;
+		regulator-max-microvolt = <3337000>;
+	};
+
+	l17 {
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+	};
+
+	l18 {
+		regulator-min-microvolt = <1750000>;
+		regulator-max-microvolt = <3337000>;
+	};
+};
+
+/*
+ * 2mA drive strength is not enough when connecting multiple
+ * I2C devices with different pull up resistors.
+ */
+&i2c2_default {
+	drive-strength = <16>;
+};
+
+&i2c4_default {
+	drive-strength = <16>;
+};
+
+&i2c6_default {
+	drive-strength = <16>;
+};
+
+/*
+ * GPIO name legend: proper name = the GPIO line is used as GPIO
+ *         NC = not connected (pin out but not routed from the chip to
+ *              anything the board)
+ *         "[PER]" = pin is muxed for [peripheral] (not GPIO)
+ *         LSEC = Low Speed External Connector
+ *         HSEC = High Speed External Connector
+ *
+ * Line names are taken from the schematic "DragonBoard410c"
+ * dated monday, august 31, 2015. Page 5 in particular.
+ *
+ * For the lines routed to the external connectors the
+ * lines are named after the 96Boards CE Specification 1.0,
+ * Appendix "Expansion Connector Signal Description".
+ *
+ * When the 96Board naming of a line and the schematic name of
+ * the same line are in conflict, the 96Board specification
+ * takes precedence, which means that the external UART on the
+ * LSEC is named UART0 while the schematic and SoC names this
+ * UART3. This is only for the informational lines i.e. "[FOO]",
+ * the GPIO named lines "GPIO-A" thru "GPIO-L" are the only
+ * ones actually used for GPIO.
+ */
+
+&msmgpio {
+	gpio-line-names =
+		"[UART0_TX]", /* GPIO_0, LSEC pin 5 */
+		"[UART0_RX]", /* GPIO_1, LSEC pin 7 */
+		"[UART0_CTS_N]", /* GPIO_2, LSEC pin 3 */
+		"[UART0_RTS_N]", /* GPIO_3, LSEC pin 9 */
+		"[UART1_TX]", /* GPIO_4, LSEC pin 11 */
+		"[UART1_RX]", /* GPIO_5, LSEC pin 13 */
+		"[I2C0_SDA]", /* GPIO_8, LSEC pin 17 */
+		"[I2C0_SCL]", /* GPIO_7, LSEC pin 15 */
+		"[SPI1_DOUT]", /* SPI1_MOSI, HSEC pin 1 */
+		"[SPI1_DIN]", /* SPI1_MISO, HSEC pin 11 */
+		"[SPI1_CS]", /* SPI1_CS_N, HSEC pin 7 */
+		"[SPI1_SCLK]", /* SPI1_CLK, HSEC pin 9 */
+		"GPIO-B", /* LS_EXP_GPIO_B, LSEC pin 24 */
+		"GPIO-C", /* LS_EXP_GPIO_C, LSEC pin 25 */
+		"[I2C3_SDA]", /* HSEC pin 38 */
+		"[I2C3_SCL]", /* HSEC pin 36 */
+		"[SPI0_MOSI]", /* LSEC pin 14 */
+		"[SPI0_MISO]", /* LSEC pin 10 */
+		"[SPI0_CS_N]", /* LSEC pin 12 */
+		"[SPI0_CLK]", /* LSEC pin 8 */
+		"HDMI_HPD_N", /* GPIO 20 */
+		"USR_LED_1_CTRL",
+		"[I2C1_SDA]", /* GPIO_22, LSEC pin 21 */
+		"[I2C1_SCL]", /* GPIO_23, LSEC pin 19 */
+		"GPIO-G", /* LS_EXP_GPIO_G, LSEC pin 29 */
+		"GPIO-H", /* LS_EXP_GPIO_H, LSEC pin 30 */
+		"[CSI0_MCLK]", /* HSEC pin 15 */
+		"[CSI1_MCLK]", /* HSEC pin 17 */
+		"GPIO-K", /* LS_EXP_GPIO_K, LSEC pin 33 */
+		"[I2C2_SDA]", /* HSEC pin 34 */
+		"[I2C2_SCL]", /* HSEC pin 32 */
+		"DSI2HDMI_INT_N",
+		"DSI_SW_SEL_APQ",
+		"GPIO-L", /* LS_EXP_GPIO_L, LSEC pin 34 */
+		"GPIO-J", /* LS_EXP_GPIO_J, LSEC pin 32 */
+		"GPIO-I", /* LS_EXP_GPIO_I, LSEC pin 31 */
+		"GPIO-A", /* LS_EXP_GPIO_A, LSEC pin 23 */
+		"FORCED_USB_BOOT",
+		"SD_CARD_DET_N",
+		"[WCSS_BT_SSBI]",
+		"[WCSS_WLAN_DATA_2]", /* GPIO 40 */
+		"[WCSS_WLAN_DATA_1]",
+		"[WCSS_WLAN_DATA_0]",
+		"[WCSS_WLAN_SET]",
+		"[WCSS_WLAN_CLK]",
+		"[WCSS_FM_SSBI]",
+		"[WCSS_FM_SDI]",
+		"[WCSS_BT_DAT_CTL]",
+		"[WCSS_BT_DAT_STB]",
+		"NC",
+		"NC", /* GPIO 50 */
+		"NC",
+		"NC",
+		"NC",
+		"NC",
+		"NC",
+		"NC",
+		"NC",
+		"NC",
+		"NC",
+		"NC", /* GPIO 60 */
+		"NC",
+		"NC",
+		"[CDC_PDM0_CLK]",
+		"[CDC_PDM0_SYNC]",
+		"[CDC_PDM0_TX0]",
+		"[CDC_PDM0_RX0]",
+		"[CDC_PDM0_RX1]",
+		"[CDC_PDM0_RX2]",
+		"GPIO-D", /* LS_EXP_GPIO_D, LSEC pin 26 */
+		"NC", /* GPIO 70 */
+		"NC",
+		"NC",
+		"NC",
+		"NC", /* GPIO 74 */
+		"NC",
+		"NC",
+		"NC",
+		"NC",
+		"NC",
+		"BOOT_CONFIG_0", /* GPIO 80 */
+		"BOOT_CONFIG_1",
+		"BOOT_CONFIG_2",
+		"BOOT_CONFIG_3",
+		"NC",
+		"NC",
+		"BOOT_CONFIG_5",
+		"NC",
+		"NC",
+		"NC",
+		"NC", /* GPIO 90 */
+		"NC",
+		"NC",
+		"NC",
+		"NC",
+		"NC",
+		"NC",
+		"NC",
+		"NC",
+		"NC",
+		"NC", /* GPIO 100 */
+		"NC",
+		"NC",
+		"NC",
+		"SSBI_GPS",
+		"NC",
+		"NC",
+		"KEY_VOLP_N",
+		"NC",
+		"NC",
+		"[LS_EXP_MI2S_WS]", /* GPIO 110 */
+		"NC",
+		"NC",
+		"[LS_EXP_MI2S_SCK]",
+		"[LS_EXP_MI2S_DATA0]",
+		"GPIO-E", /* LS_EXP_GPIO_E, LSEC pin 27 */
+		"NC",
+		"[DSI2HDMI_MI2S_WS]",
+		"[DSI2HDMI_MI2S_SCK]",
+		"[DSI2HDMI_MI2S_DATA0]",
+		"USR_LED_2_CTRL", /* GPIO 120 */
+		"SB_HS_ID";
+
+	msmgpio_leds: msmgpio-leds {
+		pins = "gpio21", "gpio120";
+		function = "gpio";
+
+		output-low;
+	};
+
+	usb_id_default: usb-id-default {
+		pins = "gpio121";
+		function = "gpio";
+
+		drive-strength = <8>;
+		input-enable;
+		bias-pull-up;
+	};
+
+	adv7533_int_active: adv533-int-active {
+		pins = "gpio31";
+		function = "gpio";
+
+		drive-strength = <16>;
+		bias-disable;
+	};
+
+	adv7533_int_suspend: adv7533-int-suspend {
+		pins = "gpio31";
+		function = "gpio";
+
+		drive-strength = <2>;
+		bias-disable;
+	};
+
+	adv7533_switch_active: adv7533-switch-active {
+		pins = "gpio32";
+		function = "gpio";
+
+		drive-strength = <16>;
+		bias-disable;
+	};
+
+	adv7533_switch_suspend: adv7533-switch-suspend {
+		pins = "gpio32";
+		function = "gpio";
+
+		drive-strength = <2>;
+		bias-disable;
+	};
+
+	msm_key_volp_n_default: msm-key-volp-n-default {
+		pins = "gpio107";
+		function = "gpio";
+
+		drive-strength = <8>;
+		input-enable;
+		bias-pull-up;
+	};
+};
+
+&pm8916_gpios {
+	gpio-line-names =
+		"USR_LED_3_CTRL",
+		"USR_LED_4_CTRL",
+		"USB_HUB_RESET_N_PM",
+		"USB_SW_SEL_PM";
+
+	usb_hub_reset_pm: usb-hub-reset-pm {
+		pins = "gpio3";
+		function = PMIC_GPIO_FUNC_NORMAL;
+
+		input-disable;
+		output-high;
+	};
+
+	usb_hub_reset_pm_device: usb-hub-reset-pm-device {
+		pins = "gpio3";
+		function = PMIC_GPIO_FUNC_NORMAL;
+
+		output-low;
+	};
+
+	usb_sw_sel_pm: usb-sw-sel-pm {
+		pins = "gpio4";
+		function = PMIC_GPIO_FUNC_NORMAL;
+
+		power-source = <PM8916_GPIO_VPH>;
+		input-disable;
+		output-high;
+	};
+
+	usb_sw_sel_pm_device: usb-sw-sel-pm-device {
+		pins = "gpio4";
+		function = PMIC_GPIO_FUNC_NORMAL;
+
+		power-source = <PM8916_GPIO_VPH>;
+		input-disable;
+		output-low;
+	};
+
+	pm8916_gpios_leds: pm8916-gpios-leds {
+		pins = "gpio1", "gpio2";
+		function = PMIC_GPIO_FUNC_NORMAL;
+
+		output-low;
+	};
+};
+
+&pm8916_mpps {
+	gpio-line-names =
+		"VDD_PX_BIAS",
+		"WLAN_LED_CTRL",
+		"BT_LED_CTRL",
+		"GPIO-F"; /* LS_EXP_GPIO_F, LSEC pin 28 */
+
+	pinctrl-names = "default";
+	pinctrl-0 = <&ls_exp_gpio_f>;
+
+	ls_exp_gpio_f: pm8916-mpp4-state {
+		pins = "mpp4";
+		function = "digital";
+
+		output-low;
+		power-source = <PM8916_MPP_L5>;	// 1.8V
+	};
+
+	pm8916_mpps_leds: pm8916-mpps-state {
+		pins = "mpp2", "mpp3";
+		function = "digital";
+
+		output-low;
+	};
 };
diff --git a/arch/arm64/boot/dts/qcom/apq8016-sbc.dtsi b/arch/arm64/boot/dts/qcom/apq8016-sbc.dtsi
deleted file mode 100644
index f8d8f3e3664e..000000000000
--- a/arch/arm64/boot/dts/qcom/apq8016-sbc.dtsi
+++ /dev/null
@@ -1,826 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0-only
-/*
- * Copyright (c) 2015, The Linux Foundation. All rights reserved.
- */
-
-#include "msm8916-pm8916.dtsi"
-#include <dt-bindings/gpio/gpio.h>
-#include <dt-bindings/input/input.h>
-#include <dt-bindings/pinctrl/qcom,pmic-gpio.h>
-#include <dt-bindings/pinctrl/qcom,pmic-mpp.h>
-#include <dt-bindings/sound/apq8016-lpass.h>
-
-/ {
-	aliases {
-		serial0 = &blsp1_uart2;
-		serial1 = &blsp1_uart1;
-		usid0 = &pm8916_0;
-		i2c0	= &blsp_i2c2;
-		i2c1	= &blsp_i2c6;
-		i2c3	= &blsp_i2c4;
-		spi0	= &blsp_spi5;
-		spi1	= &blsp_spi3;
-	};
-
-	chosen {
-		stdout-path = "serial0";
-	};
-
-	camera_vdddo_1v8: camera-vdddo-1v8 {
-		compatible = "regulator-fixed";
-		regulator-name = "camera_vdddo";
-		regulator-min-microvolt = <1800000>;
-		regulator-max-microvolt = <1800000>;
-		regulator-always-on;
-	};
-
-	camera_vdda_2v8: camera-vdda-2v8 {
-		compatible = "regulator-fixed";
-		regulator-name = "camera_vdda";
-		regulator-min-microvolt = <2800000>;
-		regulator-max-microvolt = <2800000>;
-		regulator-always-on;
-	};
-
-	camera_vddd_1v5: camera-vddd-1v5 {
-		compatible = "regulator-fixed";
-		regulator-name = "camera_vddd";
-		regulator-min-microvolt = <1500000>;
-		regulator-max-microvolt = <1500000>;
-		regulator-always-on;
-	};
-
-	reserved-memory {
-		ramoops@bff00000 {
-			compatible = "ramoops";
-			reg = <0x0 0xbff00000 0x0 0x100000>;
-
-			record-size = <0x20000>;
-			console-size = <0x20000>;
-			ftrace-size = <0x20000>;
-		};
-	};
-
-	usb2513 {
-		compatible = "smsc,usb3503";
-		reset-gpios = <&pm8916_gpios 3 GPIO_ACTIVE_LOW>;
-		initial-mode = <1>;
-	};
-
-	usb_id: usb-id {
-		compatible = "linux,extcon-usb-gpio";
-		id-gpio = <&msmgpio 121 GPIO_ACTIVE_HIGH>;
-		pinctrl-names = "default";
-		pinctrl-0 = <&usb_id_default>;
-	};
-
-	hdmi-out {
-		compatible = "hdmi-connector";
-		type = "a";
-
-		port {
-			hdmi_con: endpoint {
-				remote-endpoint = <&adv7533_out>;
-			};
-		};
-	};
-
-	gpio-keys {
-		compatible = "gpio-keys";
-		#address-cells = <1>;
-		#size-cells = <0>;
-		autorepeat;
-
-		pinctrl-names = "default";
-		pinctrl-0 = <&msm_key_volp_n_default>;
-
-		button@0 {
-			label = "Volume Up";
-			linux,code = <KEY_VOLUMEUP>;
-			gpios = <&msmgpio 107 GPIO_ACTIVE_LOW>;
-		};
-	};
-
-	leds {
-		pinctrl-names = "default";
-		pinctrl-0 = <&msmgpio_leds>,
-			    <&pm8916_gpios_leds>,
-			    <&pm8916_mpps_leds>;
-
-		compatible = "gpio-leds";
-
-		led@1 {
-			label = "apq8016-sbc:green:user1";
-			gpios = <&msmgpio 21 GPIO_ACTIVE_HIGH>;
-			linux,default-trigger = "heartbeat";
-			default-state = "off";
-		};
-
-		led@2 {
-			label = "apq8016-sbc:green:user2";
-			gpios = <&msmgpio 120 GPIO_ACTIVE_HIGH>;
-			linux,default-trigger = "mmc0";
-			default-state = "off";
-		};
-
-		led@3 {
-			label = "apq8016-sbc:green:user3";
-			gpios = <&pm8916_gpios 1 GPIO_ACTIVE_HIGH>;
-			linux,default-trigger = "mmc1";
-			default-state = "off";
-		};
-
-		led@4 {
-			label = "apq8016-sbc:green:user4";
-			gpios = <&pm8916_gpios 2 GPIO_ACTIVE_HIGH>;
-			linux,default-trigger = "none";
-			panic-indicator;
-			default-state = "off";
-		};
-
-		led@5 {
-			label = "apq8016-sbc:yellow:wlan";
-			gpios = <&pm8916_mpps 2 GPIO_ACTIVE_HIGH>;
-			linux,default-trigger = "phy0tx";
-			default-state = "off";
-		};
-
-		led@6 {
-			label = "apq8016-sbc:blue:bt";
-			gpios = <&pm8916_mpps 3 GPIO_ACTIVE_HIGH>;
-			linux,default-trigger = "bluetooth-power";
-			default-state = "off";
-		};
-	};
-};
-
-&blsp_dma {
-	status = "okay";
-};
-
-&blsp_i2c2 {
-	/* On Low speed expansion */
-	status = "okay";
-	label = "LS-I2C0";
-};
-
-&blsp_i2c4 {
-	/* On High speed expansion */
-	status = "okay";
-	label = "HS-I2C2";
-
-	adv_bridge: bridge@39 {
-		status = "okay";
-
-		compatible = "adi,adv7533";
-		reg = <0x39>;
-
-		interrupt-parent = <&msmgpio>;
-		interrupts = <31 IRQ_TYPE_EDGE_FALLING>;
-
-		adi,dsi-lanes = <4>;
-		clocks = <&rpmcc RPM_SMD_BB_CLK2>;
-		clock-names = "cec";
-
-		pd-gpios = <&msmgpio 32 GPIO_ACTIVE_HIGH>;
-
-		avdd-supply = <&pm8916_l6>;
-		v1p2-supply = <&pm8916_l6>;
-		v3p3-supply = <&pm8916_l17>;
-
-		pinctrl-names = "default","sleep";
-		pinctrl-0 = <&adv7533_int_active &adv7533_switch_active>;
-		pinctrl-1 = <&adv7533_int_suspend &adv7533_switch_suspend>;
-		#sound-dai-cells = <1>;
-
-		ports {
-			#address-cells = <1>;
-			#size-cells = <0>;
-
-			port@0 {
-				reg = <0>;
-				adv7533_in: endpoint {
-					remote-endpoint = <&dsi0_out>;
-				};
-			};
-
-			port@1 {
-				reg = <1>;
-				adv7533_out: endpoint {
-					remote-endpoint = <&hdmi_con>;
-				};
-			};
-		};
-	};
-};
-
-&blsp_i2c6 {
-	/* On Low speed expansion */
-	status = "okay";
-	label = "LS-I2C1";
-};
-
-&blsp_spi3 {
-	/* On High speed expansion */
-	status = "okay";
-	label = "HS-SPI1";
-};
-
-&blsp_spi5 {
-	/* On Low speed expansion */
-	status = "okay";
-	label = "LS-SPI0";
-};
-
-&blsp1_uart1 {
-	status = "okay";
-	label = "LS-UART0";
-};
-
-&blsp1_uart2 {
-	status = "okay";
-	label = "LS-UART1";
-};
-
-&camss {
-	status = "okay";
-	ports {
-		port@0 {
-			reg = <0>;
-			csiphy0_ep: endpoint {
-				clock-lanes = <1>;
-				data-lanes = <0 2>;
-				remote-endpoint = <&ov5640_ep>;
-				status = "okay";
-			};
-		};
-	};
-};
-
-&cci {
-	status = "okay";
-};
-
-&cci_i2c0 {
-	camera_rear@3b {
-		compatible = "ovti,ov5640";
-		reg = <0x3b>;
-
-		enable-gpios = <&msmgpio 34 GPIO_ACTIVE_HIGH>;
-		reset-gpios = <&msmgpio 35 GPIO_ACTIVE_LOW>;
-		pinctrl-names = "default";
-		pinctrl-0 = <&camera_rear_default>;
-
-		clocks = <&gcc GCC_CAMSS_MCLK0_CLK>;
-		clock-names = "xclk";
-		clock-frequency = <23880000>;
-
-		vdddo-supply = <&camera_vdddo_1v8>;
-		vdda-supply = <&camera_vdda_2v8>;
-		vddd-supply = <&camera_vddd_1v5>;
-
-		/* No camera mezzanine by default */
-		status = "disabled";
-
-		port {
-			ov5640_ep: endpoint {
-				clock-lanes = <1>;
-				data-lanes = <0 2>;
-				remote-endpoint = <&csiphy0_ep>;
-			};
-		};
-	};
-};
-
-&dsi0_out {
-	data-lanes = <0 1 2 3>;
-	remote-endpoint = <&adv7533_in>;
-};
-
-&lpass {
-	status = "okay";
-};
-
-&mdss {
-	status = "okay";
-};
-
-&pm8916_resin {
-	status = "okay";
-	linux,code = <KEY_VOLUMEDOWN>;
-};
-
-&pronto {
-	status = "okay";
-};
-
-&sdhc_1 {
-	status = "okay";
-
-	pinctrl-names = "default", "sleep";
-	pinctrl-0 = <&sdc1_clk_on &sdc1_cmd_on &sdc1_data_on>;
-	pinctrl-1 = <&sdc1_clk_off &sdc1_cmd_off &sdc1_data_off>;
-};
-
-&sdhc_2 {
-	status = "okay";
-
-	pinctrl-names = "default", "sleep";
-	pinctrl-0 = <&sdc2_clk_on &sdc2_cmd_on &sdc2_data_on &sdc2_cd_on>;
-	pinctrl-1 = <&sdc2_clk_off &sdc2_cmd_off &sdc2_data_off &sdc2_cd_off>;
-
-	cd-gpios = <&msmgpio 38 GPIO_ACTIVE_LOW>;
-};
-
-&sound {
-	status = "okay";
-
-	pinctrl-0 = <&cdc_pdm_lines_act &ext_sec_tlmm_lines_act &ext_mclk_tlmm_lines_act>;
-	pinctrl-1 = <&cdc_pdm_lines_sus &ext_sec_tlmm_lines_sus &ext_mclk_tlmm_lines_sus>;
-	pinctrl-names = "default", "sleep";
-	qcom,model = "DB410c";
-	qcom,audio-routing =
-		"AMIC2", "MIC BIAS Internal2",
-		"AMIC3", "MIC BIAS External1";
-
-	external-dai-link@0 {
-		link-name = "ADV7533";
-		cpu {
-			sound-dai = <&lpass MI2S_QUATERNARY>;
-		};
-		codec {
-			sound-dai = <&adv_bridge 0>;
-		};
-	};
-
-	internal-codec-playback-dai-link@0 {
-		link-name = "WCD";
-		cpu {
-			sound-dai = <&lpass MI2S_PRIMARY>;
-		};
-		codec {
-			sound-dai = <&lpass_codec 0>, <&wcd_codec 0>;
-		};
-	};
-
-	internal-codec-capture-dai-link@0 {
-		link-name = "WCD-Capture";
-		cpu {
-			sound-dai = <&lpass MI2S_TERTIARY>;
-		};
-		codec {
-			sound-dai = <&lpass_codec 1>, <&wcd_codec 1>;
-		};
-	};
-};
-
-&usb {
-	status = "okay";
-	extcon = <&usb_id>, <&usb_id>;
-
-	pinctrl-names = "default", "device";
-	pinctrl-0 = <&usb_sw_sel_pm &usb_hub_reset_pm>;
-	pinctrl-1 = <&usb_sw_sel_pm_device &usb_hub_reset_pm_device>;
-};
-
-&usb_hs_phy {
-	extcon = <&usb_id>;
-};
-
-&wcd_codec {
-	clocks = <&gcc GCC_CODEC_DIGCODEC_CLK>;
-	clock-names = "mclk";
-	qcom,mbhc-vthreshold-low = <75 150 237 450 500>;
-	qcom,mbhc-vthreshold-high = <75 150 237 450 500>;
-};
-
-/* Enable CoreSight */
-&cti0 { status = "okay"; };
-&cti1 { status = "okay"; };
-&cti12 { status = "okay"; };
-&cti13 { status = "okay"; };
-&cti14 { status = "okay"; };
-&cti15 { status = "okay"; };
-&debug0 { status = "okay"; };
-&debug1 { status = "okay"; };
-&debug2 { status = "okay"; };
-&debug3 { status = "okay"; };
-&etf { status = "okay"; };
-&etm0 { status = "okay"; };
-&etm1 { status = "okay"; };
-&etm2 { status = "okay"; };
-&etm3 { status = "okay"; };
-&etr { status = "okay"; };
-&funnel0 { status = "okay"; };
-&funnel1 { status = "okay"; };
-&replicator { status = "okay"; };
-&stm { status = "okay"; };
-&tpiu { status = "okay"; };
-
-&smd_rpm_regulators {
-	vdd_l1_l2_l3-supply = <&pm8916_s3>;
-	vdd_l4_l5_l6-supply = <&pm8916_s4>;
-	vdd_l7-supply = <&pm8916_s4>;
-
-	s3 {
-		regulator-min-microvolt = <375000>;
-		regulator-max-microvolt = <1562000>;
-	};
-
-	s4 {
-		regulator-min-microvolt = <1800000>;
-		regulator-max-microvolt = <1800000>;
-
-		regulator-always-on;
-		regulator-boot-on;
-	};
-
-	l1 {
-		regulator-min-microvolt = <375000>;
-		regulator-max-microvolt = <1525000>;
-	};
-
-	l2 {
-		regulator-min-microvolt = <1200000>;
-		regulator-max-microvolt = <1200000>;
-	};
-
-	l4 {
-		regulator-min-microvolt = <1750000>;
-		regulator-max-microvolt = <3337000>;
-	};
-
-	l5 {
-		regulator-min-microvolt = <1750000>;
-		regulator-max-microvolt = <3337000>;
-	};
-
-	l6 {
-		regulator-min-microvolt = <1800000>;
-		regulator-max-microvolt = <1800000>;
-	};
-
-	l7 {
-		regulator-min-microvolt = <1750000>;
-		regulator-max-microvolt = <3337000>;
-	};
-
-	l8 {
-		regulator-min-microvolt = <1750000>;
-		regulator-max-microvolt = <3337000>;
-	};
-
-	l9 {
-		regulator-min-microvolt = <1750000>;
-		regulator-max-microvolt = <3337000>;
-	};
-
-	l10 {
-		regulator-min-microvolt = <1750000>;
-		regulator-max-microvolt = <3337000>;
-	};
-
-	l11 {
-		regulator-min-microvolt = <1750000>;
-		regulator-max-microvolt = <3337000>;
-		regulator-allow-set-load;
-		regulator-system-load = <200000>;
-	};
-
-	l12 {
-		regulator-min-microvolt = <1750000>;
-		regulator-max-microvolt = <3337000>;
-	};
-
-	l13 {
-		regulator-min-microvolt = <1750000>;
-		regulator-max-microvolt = <3337000>;
-	};
-
-	l14 {
-		regulator-min-microvolt = <1750000>;
-		regulator-max-microvolt = <3337000>;
-	};
-
-	/**
-	 * 1.8v required on LS expansion
-	 * for mezzanine boards
-	 */
-	l15 {
-		regulator-min-microvolt = <1750000>;
-		regulator-max-microvolt = <3337000>;
-		regulator-always-on;
-	};
-
-	l16 {
-		regulator-min-microvolt = <1750000>;
-		regulator-max-microvolt = <3337000>;
-	};
-
-	l17 {
-		regulator-min-microvolt = <3300000>;
-		regulator-max-microvolt = <3300000>;
-	};
-
-	l18 {
-		regulator-min-microvolt = <1750000>;
-		regulator-max-microvolt = <3337000>;
-	};
-};
-
-/*
- * 2mA drive strength is not enough when connecting multiple
- * I2C devices with different pull up resistors.
- */
-&i2c2_default {
-	drive-strength = <16>;
-};
-
-&i2c4_default {
-	drive-strength = <16>;
-};
-
-&i2c6_default {
-	drive-strength = <16>;
-};
-
-/*
- * GPIO name legend: proper name = the GPIO line is used as GPIO
- *         NC = not connected (pin out but not routed from the chip to
- *              anything the board)
- *         "[PER]" = pin is muxed for [peripheral] (not GPIO)
- *         LSEC = Low Speed External Connector
- *         HSEC = High Speed External Connector
- *
- * Line names are taken from the schematic "DragonBoard410c"
- * dated monday, august 31, 2015. Page 5 in particular.
- *
- * For the lines routed to the external connectors the
- * lines are named after the 96Boards CE Specification 1.0,
- * Appendix "Expansion Connector Signal Description".
- *
- * When the 96Board naming of a line and the schematic name of
- * the same line are in conflict, the 96Board specification
- * takes precedence, which means that the external UART on the
- * LSEC is named UART0 while the schematic and SoC names this
- * UART3. This is only for the informational lines i.e. "[FOO]",
- * the GPIO named lines "GPIO-A" thru "GPIO-L" are the only
- * ones actually used for GPIO.
- */
-
-&msmgpio {
-	gpio-line-names =
-		"[UART0_TX]", /* GPIO_0, LSEC pin 5 */
-		"[UART0_RX]", /* GPIO_1, LSEC pin 7 */
-		"[UART0_CTS_N]", /* GPIO_2, LSEC pin 3 */
-		"[UART0_RTS_N]", /* GPIO_3, LSEC pin 9 */
-		"[UART1_TX]", /* GPIO_4, LSEC pin 11 */
-		"[UART1_RX]", /* GPIO_5, LSEC pin 13 */
-		"[I2C0_SDA]", /* GPIO_8, LSEC pin 17 */
-		"[I2C0_SCL]", /* GPIO_7, LSEC pin 15 */
-		"[SPI1_DOUT]", /* SPI1_MOSI, HSEC pin 1 */
-		"[SPI1_DIN]", /* SPI1_MISO, HSEC pin 11 */
-		"[SPI1_CS]", /* SPI1_CS_N, HSEC pin 7 */
-		"[SPI1_SCLK]", /* SPI1_CLK, HSEC pin 9 */
-		"GPIO-B", /* LS_EXP_GPIO_B, LSEC pin 24 */
-		"GPIO-C", /* LS_EXP_GPIO_C, LSEC pin 25 */
-		"[I2C3_SDA]", /* HSEC pin 38 */
-		"[I2C3_SCL]", /* HSEC pin 36 */
-		"[SPI0_MOSI]", /* LSEC pin 14 */
-		"[SPI0_MISO]", /* LSEC pin 10 */
-		"[SPI0_CS_N]", /* LSEC pin 12 */
-		"[SPI0_CLK]", /* LSEC pin 8 */
-		"HDMI_HPD_N", /* GPIO 20 */
-		"USR_LED_1_CTRL",
-		"[I2C1_SDA]", /* GPIO_22, LSEC pin 21 */
-		"[I2C1_SCL]", /* GPIO_23, LSEC pin 19 */
-		"GPIO-G", /* LS_EXP_GPIO_G, LSEC pin 29 */
-		"GPIO-H", /* LS_EXP_GPIO_H, LSEC pin 30 */
-		"[CSI0_MCLK]", /* HSEC pin 15 */
-		"[CSI1_MCLK]", /* HSEC pin 17 */
-		"GPIO-K", /* LS_EXP_GPIO_K, LSEC pin 33 */
-		"[I2C2_SDA]", /* HSEC pin 34 */
-		"[I2C2_SCL]", /* HSEC pin 32 */
-		"DSI2HDMI_INT_N",
-		"DSI_SW_SEL_APQ",
-		"GPIO-L", /* LS_EXP_GPIO_L, LSEC pin 34 */
-		"GPIO-J", /* LS_EXP_GPIO_J, LSEC pin 32 */
-		"GPIO-I", /* LS_EXP_GPIO_I, LSEC pin 31 */
-		"GPIO-A", /* LS_EXP_GPIO_A, LSEC pin 23 */
-		"FORCED_USB_BOOT",
-		"SD_CARD_DET_N",
-		"[WCSS_BT_SSBI]",
-		"[WCSS_WLAN_DATA_2]", /* GPIO 40 */
-		"[WCSS_WLAN_DATA_1]",
-		"[WCSS_WLAN_DATA_0]",
-		"[WCSS_WLAN_SET]",
-		"[WCSS_WLAN_CLK]",
-		"[WCSS_FM_SSBI]",
-		"[WCSS_FM_SDI]",
-		"[WCSS_BT_DAT_CTL]",
-		"[WCSS_BT_DAT_STB]",
-		"NC",
-		"NC", /* GPIO 50 */
-		"NC",
-		"NC",
-		"NC",
-		"NC",
-		"NC",
-		"NC",
-		"NC",
-		"NC",
-		"NC",
-		"NC", /* GPIO 60 */
-		"NC",
-		"NC",
-		"[CDC_PDM0_CLK]",
-		"[CDC_PDM0_SYNC]",
-		"[CDC_PDM0_TX0]",
-		"[CDC_PDM0_RX0]",
-		"[CDC_PDM0_RX1]",
-		"[CDC_PDM0_RX2]",
-		"GPIO-D", /* LS_EXP_GPIO_D, LSEC pin 26 */
-		"NC", /* GPIO 70 */
-		"NC",
-		"NC",
-		"NC",
-		"NC", /* GPIO 74 */
-		"NC",
-		"NC",
-		"NC",
-		"NC",
-		"NC",
-		"BOOT_CONFIG_0", /* GPIO 80 */
-		"BOOT_CONFIG_1",
-		"BOOT_CONFIG_2",
-		"BOOT_CONFIG_3",
-		"NC",
-		"NC",
-		"BOOT_CONFIG_5",
-		"NC",
-		"NC",
-		"NC",
-		"NC", /* GPIO 90 */
-		"NC",
-		"NC",
-		"NC",
-		"NC",
-		"NC",
-		"NC",
-		"NC",
-		"NC",
-		"NC",
-		"NC", /* GPIO 100 */
-		"NC",
-		"NC",
-		"NC",
-		"SSBI_GPS",
-		"NC",
-		"NC",
-		"KEY_VOLP_N",
-		"NC",
-		"NC",
-		"[LS_EXP_MI2S_WS]", /* GPIO 110 */
-		"NC",
-		"NC",
-		"[LS_EXP_MI2S_SCK]",
-		"[LS_EXP_MI2S_DATA0]",
-		"GPIO-E", /* LS_EXP_GPIO_E, LSEC pin 27 */
-		"NC",
-		"[DSI2HDMI_MI2S_WS]",
-		"[DSI2HDMI_MI2S_SCK]",
-		"[DSI2HDMI_MI2S_DATA0]",
-		"USR_LED_2_CTRL", /* GPIO 120 */
-		"SB_HS_ID";
-
-	msmgpio_leds: msmgpio-leds {
-		pins = "gpio21", "gpio120";
-		function = "gpio";
-
-		output-low;
-	};
-
-	usb_id_default: usb-id-default {
-		pins = "gpio121";
-		function = "gpio";
-
-		drive-strength = <8>;
-		input-enable;
-		bias-pull-up;
-	};
-
-	adv7533_int_active: adv533-int-active {
-		pins = "gpio31";
-		function = "gpio";
-
-		drive-strength = <16>;
-		bias-disable;
-	};
-
-	adv7533_int_suspend: adv7533-int-suspend {
-		pins = "gpio31";
-		function = "gpio";
-
-		drive-strength = <2>;
-		bias-disable;
-	};
-
-	adv7533_switch_active: adv7533-switch-active {
-		pins = "gpio32";
-		function = "gpio";
-
-		drive-strength = <16>;
-		bias-disable;
-	};
-
-	adv7533_switch_suspend: adv7533-switch-suspend {
-		pins = "gpio32";
-		function = "gpio";
-
-		drive-strength = <2>;
-		bias-disable;
-	};
-
-	msm_key_volp_n_default: msm-key-volp-n-default {
-		pins = "gpio107";
-		function = "gpio";
-
-		drive-strength = <8>;
-		input-enable;
-		bias-pull-up;
-	};
-};
-
-&pm8916_gpios {
-	gpio-line-names =
-		"USR_LED_3_CTRL",
-		"USR_LED_4_CTRL",
-		"USB_HUB_RESET_N_PM",
-		"USB_SW_SEL_PM";
-
-	usb_hub_reset_pm: usb-hub-reset-pm {
-		pins = "gpio3";
-		function = PMIC_GPIO_FUNC_NORMAL;
-
-		input-disable;
-		output-high;
-	};
-
-	usb_hub_reset_pm_device: usb-hub-reset-pm-device {
-		pins = "gpio3";
-		function = PMIC_GPIO_FUNC_NORMAL;
-
-		output-low;
-	};
-
-	usb_sw_sel_pm: usb-sw-sel-pm {
-		pins = "gpio4";
-		function = PMIC_GPIO_FUNC_NORMAL;
-
-		power-source = <PM8916_GPIO_VPH>;
-		input-disable;
-		output-high;
-	};
-
-	usb_sw_sel_pm_device: usb-sw-sel-pm-device {
-		pins = "gpio4";
-		function = PMIC_GPIO_FUNC_NORMAL;
-
-		power-source = <PM8916_GPIO_VPH>;
-		input-disable;
-		output-low;
-	};
-
-	pm8916_gpios_leds: pm8916-gpios-leds {
-		pins = "gpio1", "gpio2";
-		function = PMIC_GPIO_FUNC_NORMAL;
-
-		output-low;
-	};
-};
-
-&pm8916_mpps {
-	gpio-line-names =
-		"VDD_PX_BIAS",
-		"WLAN_LED_CTRL",
-		"BT_LED_CTRL",
-		"GPIO-F"; /* LS_EXP_GPIO_F, LSEC pin 28 */
-
-	pinctrl-names = "default";
-	pinctrl-0 = <&ls_exp_gpio_f>;
-
-	ls_exp_gpio_f: pm8916-mpp4 {
-		pins = "mpp4";
-		function = "digital";
-
-		output-low;
-		power-source = <PM8916_MPP_L5>;	// 1.8V
-	};
-
-	pm8916_mpps_leds: pm8916-mpps-leds {
-		pins = "mpp2", "mpp3";
-		function = "digital";
-
-		output-low;
-	};
-};
diff --git a/arch/arm64/boot/dts/qcom/apq8094-sony-xperia-kitakami-karin_windy.dts b/arch/arm64/boot/dts/qcom/apq8094-sony-xperia-kitakami-karin_windy.dts
index a8dffc8c64ea..314d2dc4726a 100644
--- a/arch/arm64/boot/dts/qcom/apq8094-sony-xperia-kitakami-karin_windy.dts
+++ b/arch/arm64/boot/dts/qcom/apq8094-sony-xperia-kitakami-karin_windy.dts
@@ -11,6 +11,7 @@
 / {
 	model = "Sony Xperia Z4 Tablet (Wi-Fi)";
 	compatible = "sony,karin_windy", "qcom,apq8094";
+	chassis-type = "tablet";
 
 	/*
 	 * This model uses the APQ variant of MSM8994 (APQ8094).
diff --git a/arch/arm64/boot/dts/qcom/apq8096-db820c.dts b/arch/arm64/boot/dts/qcom/apq8096-db820c.dts
index 757afa27424d..d01a512634cf 100644
--- a/arch/arm64/boot/dts/qcom/apq8096-db820c.dts
+++ b/arch/arm64/boot/dts/qcom/apq8096-db820c.dts
@@ -5,9 +5,1077 @@
 
 /dts-v1/;
 
-#include "apq8096-db820c.dtsi"
+#include "msm8996.dtsi"
+#include "pm8994.dtsi"
+#include "pmi8994.dtsi"
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/pinctrl/qcom,pmic-gpio.h>
+#include <dt-bindings/sound/qcom,q6afe.h>
+#include <dt-bindings/sound/qcom,q6asm.h>
+
+/*
+ * GPIO name legend: proper name = the GPIO line is used as GPIO
+ *         NC      = not connected (pin out but not routed from the chip to
+ *                   anything the board)
+ *         "[PER]" = pin is muxed for [peripheral] (not GPIO)
+ *         LSEC    = Low Speed External Connector
+ *         P HSEC  = Primary High Speed External Connector
+ *         S HSEC  = Secondary High Speed External Connector
+ *         J14     = Camera Connector
+ *         TP      = Test Points
+ *
+ * Line names are taken from the schematic "DragonBoard 820c",
+ * drawing no: LM25-P2751-1
+ *
+ * For the lines routed to the external connectors the
+ * lines are named after the 96Boards CE Specification 1.0,
+ * Appendix "Expansion Connector Signal Description".
+ *
+ * When the 96Board naming of a line and the schematic name of
+ * the same line are in conflict, the 96Board specification
+ * takes precedence, which means that the external UART on the
+ * LSEC is named UART0 while the schematic and SoC names this
+ * UART3. This is only for the informational lines i.e. "[FOO]",
+ * the GPIO named lines "GPIO-A" thru "GPIO-L" are the only
+ * ones actually used for GPIO.
+ */
 
 / {
 	model = "Qualcomm Technologies, Inc. DB820c";
 	compatible = "arrow,apq8096-db820c", "qcom,apq8096-sbc", "qcom,apq8096";
+
+	aliases {
+		serial0 = &blsp2_uart2;
+		serial1 = &blsp2_uart3;
+		serial2 = &blsp1_uart2;
+		i2c0	= &blsp1_i2c3;
+		i2c1	= &blsp2_i2c1;
+		i2c2	= &blsp2_i2c1;
+		spi0	= &blsp1_spi1;
+		spi1	= &blsp2_spi6;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	clocks {
+		compatible = "simple-bus";
+		divclk4: divclk4 {
+			compatible = "fixed-clock";
+			#clock-cells = <0>;
+			clock-frequency = <32768>;
+			clock-output-names = "divclk4";
+
+			pinctrl-names = "default";
+			pinctrl-0 = <&divclk4_pin_a>;
+		};
+
+		div1_mclk: divclk1 {
+			compatible = "gpio-gate-clock";
+			pinctrl-0 = <&audio_mclk>;
+			pinctrl-names = "default";
+			clocks = <&rpmcc RPM_SMD_DIV_CLK1>;
+			#clock-cells = <0>;
+			enable-gpios = <&pm8994_gpios 15 0>;
+		};
+	};
+
+	gpio_keys {
+		compatible = "gpio-keys";
+		#address-cells = <1>;
+		#size-cells = <0>;
+		autorepeat;
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&volume_up_gpio>;
+
+		button@0 {
+			label = "Volume Up";
+			linux,code = <KEY_VOLUMEUP>;
+			gpios = <&pm8994_gpios 2 GPIO_ACTIVE_LOW>;
+		};
+	};
+
+	usb2_id: usb2-id {
+		compatible = "linux,extcon-usb-gpio";
+		id-gpio = <&pmi8994_gpios 6 GPIO_ACTIVE_HIGH>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&usb2_vbus_det_gpio>;
+	};
+
+	usb3_id: usb3-id {
+		compatible = "linux,extcon-usb-gpio";
+		id-gpio = <&pm8994_gpios 22 GPIO_ACTIVE_HIGH>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&usb3_vbus_det_gpio>;
+	};
+
+	vph_pwr: vph-pwr-regulator {
+		compatible = "regulator-fixed";
+		regulator-name = "vph_pwr";
+		regulator-always-on;
+		regulator-boot-on;
+
+		regulator-min-microvolt = <3700000>;
+		regulator-max-microvolt = <3700000>;
+	};
+
+	wlan_en: wlan-en-1-8v {
+		pinctrl-names = "default";
+		pinctrl-0 = <&wlan_en_gpios>;
+		compatible = "regulator-fixed";
+		regulator-name = "wlan-en-regulator";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+
+		gpio = <&pm8994_gpios 8 0>;
+
+		/* WLAN card specific delay */
+		startup-delay-us = <70000>;
+		enable-active-high;
+	};
+};
+
+&blsp1_i2c3 {
+	/* On Low speed expansion */
+	label = "LS-I2C0";
+	status = "okay";
+};
+
+&blsp1_spi1 {
+	/* On Low speed expansion */
+	label = "LS-SPI0";
+	status = "okay";
+};
+
+&blsp1_uart2 {
+	label = "BT-UART";
+	status = "okay";
+
+	bluetooth {
+		compatible = "qcom,qca6174-bt";
+
+		/* bt_disable_n gpio */
+		enable-gpios = <&pm8994_gpios 19 GPIO_ACTIVE_HIGH>;
+
+		clocks = <&divclk4>;
+	};
+};
+
+&adsp_pil {
+	status = "okay";
+};
+
+&blsp2_i2c1 {
+	/* On High speed expansion */
+	label = "HS-I2C2";
+	status = "okay";
+};
+
+&blsp2_i2c1 {
+	/* On Low speed expansion */
+	label = "LS-I2C1";
+	status = "okay";
+};
+
+&blsp2_spi6 {
+	/* On High speed expansion */
+	label = "HS-SPI1";
+	status = "okay";
+};
+
+&blsp2_uart2 {
+	label = "LS-UART1";
+	status = "okay";
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&blsp2_uart2_2pins_default>;
+	pinctrl-1 = <&blsp2_uart2_2pins_sleep>;
+};
+
+&blsp2_uart3 {
+	label = "LS-UART0";
+	status = "disabled";
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&blsp2_uart3_4pins_default>;
+	pinctrl-1 = <&blsp2_uart3_4pins_sleep>;
+};
+
+&camss {
+	vdda-supply = <&vreg_l2a_1p25>;
+};
+
+&gpu {
+	status = "okay";
+};
+
+&hdmi {
+	status = "okay";
+
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&hdmi_hpd_active &hdmi_ddc_active>;
+	pinctrl-1 = <&hdmi_hpd_suspend &hdmi_ddc_suspend>;
+
+	core-vdda-supply = <&vreg_l12a_1p8>;
+	core-vcc-supply = <&vreg_s4a_1p8>;
+};
+
+&hdmi_phy {
+	status = "okay";
+
+	vddio-supply = <&vreg_l12a_1p8>;
+	vcca-supply = <&vreg_l28a_0p925>;
+	#phy-cells = <0>;
+};
+
+&hsusb_phy1 {
+	status = "okay";
+
+	vdda-pll-supply = <&vreg_l12a_1p8>;
+	vdda-phy-dpdm-supply = <&vreg_l24a_3p075>;
+};
+
+&hsusb_phy2 {
+	status = "okay";
+
+	vdda-pll-supply = <&vreg_l12a_1p8>;
+	vdda-phy-dpdm-supply = <&vreg_l24a_3p075>;
+};
+
+&mdp {
+	status = "okay";
+};
+
+&mdss {
+	status = "okay";
+};
+
+&mmcc {
+	vdd-gfx-supply = <&vdd_gfx>;
+};
+
+&pm8994_resin {
+	status = "okay";
+	linux,code = <KEY_VOLUMEDOWN>;
+};
+
+&tlmm {
+	gpio-line-names =
+		"[SPI0_DOUT]", /* GPIO_0, BLSP1_SPI_MOSI, LSEC pin 14 */
+		"[SPI0_DIN]", /* GPIO_1, BLSP1_SPI_MISO, LSEC pin 10 */
+		"[SPI0_CS]", /* GPIO_2, BLSP1_SPI_CS_N, LSEC pin 12 */
+		"[SPI0_SCLK]", /* GPIO_3, BLSP1_SPI_CLK, LSEC pin 8 */
+		"[UART1_TxD]", /* GPIO_4, BLSP8_UART_TX, LSEC pin 11 */
+		"[UART1_RxD]", /* GPIO_5, BLSP8_UART_RX, LSEC pin 13 */
+		"[I2C1_SDA]", /* GPIO_6, BLSP8_I2C_SDA, LSEC pin 21 */
+		"[I2C1_SCL]", /* GPIO_7, BLSP8_I2C_SCL, LSEC pin 19 */
+		"GPIO-H", /* GPIO_8, LCD0_RESET_N, LSEC pin 30 */
+		"TP93", /* GPIO_9 */
+		"GPIO-G", /* GPIO_10, MDP_VSYNC_P, LSEC pin 29 */
+		"[MDP_VSYNC_S]", /* GPIO_11, S HSEC pin 55 */
+		"NC", /* GPIO_12 */
+		"[CSI0_MCLK]", /* GPIO_13, CAM_MCLK0, P HSEC pin 15 */
+		"[CAM_MCLK1]", /* GPIO_14, J14 pin 11 */
+		"[CSI1_MCLK]", /* GPIO_15, CAM_MCLK2, P HSEC pin 17 */
+		"TP99", /* GPIO_16 */
+		"[I2C2_SDA]", /* GPIO_17, CCI_I2C_SDA0, P HSEC pin 34 */
+		"[I2C2_SCL]", /* GPIO_18, CCI_I2C_SCL0, P HSEC pin 32 */
+		"[CCI_I2C_SDA1]", /* GPIO_19, S HSEC pin 38 */
+		"[CCI_I2C_SCL1]", /* GPIO_20, S HSEC pin 36 */
+		"FLASH_STROBE_EN", /* GPIO_21, S HSEC pin 5 */
+		"FLASH_STROBE_TRIG", /* GPIO_22, S HSEC pin 1 */
+		"GPIO-K", /* GPIO_23, CAM2_RST_N, LSEC pin 33 */
+		"GPIO-D", /* GPIO_24, LSEC pin 26 */
+		"GPIO-I", /* GPIO_25, CAM0_RST_N, LSEC pin 31 */
+		"GPIO-J", /* GPIO_26, CAM0_STANDBY_N, LSEC pin 32 */
+		"BLSP6_I2C_SDA", /* GPIO_27 */
+		"BLSP6_I2C_SCL", /* GPIO_28 */
+		"GPIO-B", /* GPIO_29, TS0_RESET_N, LSEC pin 24 */
+		"GPIO30", /* GPIO_30, S HSEC pin 4 */
+		"HDMI_CEC", /* GPIO_31 */
+		"HDMI_DDC_CLOCK", /* GPIO_32 */
+		"HDMI_DDC_DATA", /* GPIO_33 */
+		"HDMI_HOT_PLUG_DETECT", /* GPIO_34 */
+		"PCIE0_RST_N", /* GPIO_35 */
+		"PCIE0_CLKREQ_N", /* GPIO_36 */
+		"PCIE0_WAKE", /* GPIO_37 */
+		"SD_CARD_DET_N", /* GPIO_38 */
+		"TSIF1_SYNC", /* GPIO_39, S HSEC pin 48 */
+		"W_DISABLE_N", /* GPIO_40 */
+		"[BLSP9_UART_TX]", /* GPIO_41 */
+		"[BLSP9_UART_RX]", /* GPIO_42 */
+		"[BLSP2_UART_CTS_N]", /* GPIO_43 */
+		"[BLSP2_UART_RFR_N]", /* GPIO_44 */
+		"[BLSP3_UART_TX]", /* GPIO_45 */
+		"[BLSP3_UART_RX]", /* GPIO_46 */
+		"[I2C0_SDA]", /* GPIO_47, LS_I2C0_SDA, LSEC pin 17 */
+		"[I2C0_SCL]", /* GPIO_48, LS_I2C0_SCL, LSEC pin 15 */
+		"[UART0_TxD]", /* GPIO_49, BLSP9_UART_TX, LSEC pin 5 */
+		"[UART0_RxD]", /* GPIO_50, BLSP9_UART_RX, LSEC pin 7 */
+		"[UART0_CTS]", /* GPIO_51, BLSP9_UART_CTS_N, LSEC pin 3 */
+		"[UART0_RTS]", /* GPIO_52, BLSP9_UART_RFR_N, LSEC pin 9 */
+		"[CODEC_INT1_N]", /* GPIO_53 */
+		"[CODEC_INT2_N]", /* GPIO_54 */
+		"[BLSP7_I2C_SDA]", /* GPIO_55 */
+		"[BLSP7_I2C_SCL]", /* GPIO_56 */
+		"MI2S_MCLK", /* GPIO_57, S HSEC pin 3 */
+		"[PCM_CLK]", /* GPIO_58, QUA_MI2S_SCK, LSEC pin 18 */
+		"[PCM_FS]", /* GPIO_59, QUA_MI2S_WS, LSEC pin 16 */
+		"[PCM_DO]", /* GPIO_60, QUA_MI2S_DATA0, LSEC pin 20 */
+		"[PCM_DI]", /* GPIO_61, QUA_MI2S_DATA1, LSEC pin 22 */
+		"GPIO-E", /* GPIO_62, LSEC pin 27 */
+		"TP87", /* GPIO_63 */
+		"[CODEC_RST_N]", /* GPIO_64 */
+		"[PCM1_CLK]", /* GPIO_65 */
+		"[PCM1_SYNC]", /* GPIO_66 */
+		"[PCM1_DIN]", /* GPIO_67 */
+		"[PCM1_DOUT]", /* GPIO_68 */
+		"AUDIO_REF_CLK", /* GPIO_69 */
+		"SLIMBUS_CLK", /* GPIO_70 */
+		"SLIMBUS_DATA0", /* GPIO_71 */
+		"SLIMBUS_DATA1", /* GPIO_72 */
+		"NC", /* GPIO_73 */
+		"NC", /* GPIO_74 */
+		"NC", /* GPIO_75 */
+		"NC", /* GPIO_76 */
+		"TP94", /* GPIO_77 */
+		"NC", /* GPIO_78 */
+		"TP95", /* GPIO_79 */
+		"GPIO-A", /* GPIO_80, MEMS_RESET_N, LSEC pin 23 */
+		"TP88", /* GPIO_81 */
+		"TP89", /* GPIO_82 */
+		"TP90", /* GPIO_83 */
+		"TP91", /* GPIO_84 */
+		"[SD_DAT0]", /* GPIO_85, BLSP12_SPI_MOSI, P HSEC pin 1 */
+		"[SD_CMD]", /* GPIO_86, BLSP12_SPI_MISO, P HSEC pin 11 */
+		"[SD_DAT3]", /* GPIO_87, BLSP12_SPI_CS_N, P HSEC pin 7 */
+		"[SD_SCLK]", /* GPIO_88, BLSP12_SPI_CLK, P HSEC pin 9 */
+		"TSIF1_CLK", /* GPIO_89, S HSEC pin 42 */
+		"TSIF1_EN", /* GPIO_90, S HSEC pin 46 */
+		"TSIF1_DATA", /* GPIO_91, S HSEC pin 44 */
+		"NC", /* GPIO_92 */
+		"TSIF2_CLK", /* GPIO_93, S HSEC pin 52 */
+		"TSIF2_EN", /* GPIO_94, S HSEC pin 56 */
+		"TSIF2_DATA", /* GPIO_95, S HSEC pin 54 */
+		"TSIF2_SYNC", /* GPIO_96, S HSEC pin 58 */
+		"NC", /* GPIO_97 */
+		"CAM1_STANDBY_N", /* GPIO_98 */
+		"NC", /* GPIO_99 */
+		"NC", /* GPIO_100 */
+		"[LCD1_RESET_N]", /* GPIO_101, S HSEC pin 51 */
+		"BOOT_CONFIG1", /* GPIO_102 */
+		"USB_HUB_RESET", /* GPIO_103 */
+		"CAM1_RST_N", /* GPIO_104 */
+		"NC", /* GPIO_105 */
+		"NC", /* GPIO_106 */
+		"NC", /* GPIO_107 */
+		"NC", /* GPIO_108 */
+		"NC", /* GPIO_109 */
+		"NC", /* GPIO_110 */
+		"NC", /* GPIO_111 */
+		"NC", /* GPIO_112 */
+		"PMI8994_BUA", /* GPIO_113 */
+		"PCIE2_RST_N", /* GPIO_114 */
+		"PCIE2_CLKREQ_N", /* GPIO_115 */
+		"PCIE2_WAKE", /* GPIO_116 */
+		"SSC_IRQ_0", /* GPIO_117 */
+		"SSC_IRQ_1", /* GPIO_118 */
+		"SSC_IRQ_2", /* GPIO_119 */
+		"NC", /* GPIO_120 */
+		"GPIO121", /* GPIO_121, S HSEC pin 2 */
+		"NC", /* GPIO_122 */
+		"SSC_IRQ_6", /* GPIO_123 */
+		"SSC_IRQ_7", /* GPIO_124 */
+		"GPIO-C", /* GPIO_125, TS_INT0, LSEC pin 25 */
+		"BOOT_CONFIG5", /* GPIO_126 */
+		"NC", /* GPIO_127 */
+		"NC", /* GPIO_128 */
+		"BOOT_CONFIG7", /* GPIO_129 */
+		"PCIE1_RST_N", /* GPIO_130 */
+		"PCIE1_CLKREQ_N", /* GPIO_131 */
+		"PCIE1_WAKE", /* GPIO_132 */
+		"GPIO-L", /* GPIO_133, CAM2_STANDBY_N, LSEC pin 34 */
+		"NC", /* GPIO_134 */
+		"NC", /* GPIO_135 */
+		"BOOT_CONFIG8", /* GPIO_136 */
+		"NC", /* GPIO_137 */
+		"NC", /* GPIO_138 */
+		"GPS_SSBI2", /* GPIO_139 */
+		"GPS_SSBI1", /* GPIO_140 */
+		"NC", /* GPIO_141 */
+		"NC", /* GPIO_142 */
+		"NC", /* GPIO_143 */
+		"BOOT_CONFIG6", /* GPIO_144 */
+		"NC", /* GPIO_145 */
+		"NC", /* GPIO_146 */
+		"NC", /* GPIO_147 */
+		"NC", /* GPIO_148 */
+		"NC"; /* GPIO_149 */
+
+	sdc2_cd_on: sdc2_cd_on {
+		mux {
+			pins = "gpio38";
+			function = "gpio";
+		};
+
+		config {
+			pins = "gpio38";
+			bias-pull-up;		/* pull up */
+			drive-strength = <16>;	/* 16 MA */
+		};
+	};
+
+	sdc2_cd_off: sdc2_cd_off {
+		mux {
+			pins = "gpio38";
+			function = "gpio";
+		};
+
+		config {
+			pins = "gpio38";
+			bias-pull-up;		/* pull up */
+			drive-strength = <2>;	/* 2 MA */
+		};
+	};
+
+	hdmi_hpd_active: hdmi_hpd_active {
+		mux {
+			pins = "gpio34";
+			function = "hdmi_hot";
+		};
+
+		config {
+			pins = "gpio34";
+			bias-pull-down;
+			drive-strength = <16>;
+		};
+	};
+
+	hdmi_hpd_suspend: hdmi_hpd_suspend {
+		mux {
+			pins = "gpio34";
+			function = "hdmi_hot";
+		};
+
+		config {
+			pins = "gpio34";
+			bias-pull-down;
+			drive-strength = <2>;
+		};
+	};
+
+	hdmi_ddc_active: hdmi_ddc_active {
+		mux {
+			pins = "gpio32", "gpio33";
+			function = "hdmi_ddc";
+		};
+
+		config {
+			pins = "gpio32", "gpio33";
+			drive-strength = <2>;
+			bias-pull-up;
+		};
+	};
+
+	hdmi_ddc_suspend: hdmi_ddc_suspend {
+		mux {
+			pins = "gpio32", "gpio33";
+			function = "hdmi_ddc";
+		};
+
+		config {
+			pins = "gpio32", "gpio33";
+			drive-strength = <2>;
+			bias-pull-down;
+		};
+	};
+};
+
+&pcie0 {
+	status = "okay";
+	perst-gpio = <&tlmm 35 GPIO_ACTIVE_LOW>;
+	vddpe-3v3-supply = <&wlan_en>;
+	vdda-supply = <&vreg_l28a_0p925>;
+};
+
+&pcie1 {
+	status = "okay";
+	perst-gpio = <&tlmm 130 GPIO_ACTIVE_LOW>;
+	vdda-supply = <&vreg_l28a_0p925>;
+};
+
+&pcie2 {
+	status = "okay";
+	perst-gpio = <&tlmm 114 GPIO_ACTIVE_LOW>;
+	vdda-supply = <&vreg_l28a_0p925>;
+};
+
+&pcie_phy {
+	status = "okay";
+
+	vdda-phy-supply = <&vreg_l28a_0p925>;
+	vdda-pll-supply = <&vreg_l12a_1p8>;
+};
+
+&pm8994_gpios {
+	gpio-line-names =
+		"NC",
+		"KEY_VOLP_N",
+		"NC",
+		"BL1_PWM",
+		"GPIO-F", /* BL0_PWM, LSEC pin 28 */
+		"BL1_EN",
+		"NC",
+		"WLAN_EN",
+		"NC",
+		"NC",
+		"NC",
+		"NC",
+		"NC",
+		"NC",
+		"DIVCLK1",
+		"DIVCLK2",
+		"DIVCLK3",
+		"DIVCLK4",
+		"BT_EN",
+		"PMIC_SLB",
+		"PMIC_BUA",
+		"USB_VBUS_DET";
+
+	pinctrl-names = "default";
+	pinctrl-0 = <&ls_exp_gpio_f &bt_en_gpios>;
+
+	ls_exp_gpio_f: pm8994_gpio5 {
+		pinconf {
+			pins = "gpio5";
+			output-low;
+			power-source = <2>; // PM8994_GPIO_S4, 1.8V
+		};
+	};
+
+	bt_en_gpios: bt_en_gpios {
+		pinconf {
+			pins = "gpio19";
+			function = PMIC_GPIO_FUNC_NORMAL;
+			output-low;
+			power-source = <PM8994_GPIO_S4>; // 1.8V
+			qcom,drive-strength = <PMIC_GPIO_STRENGTH_LOW>;
+			bias-pull-down;
+		};
+	};
+
+	wlan_en_gpios: wlan_en_gpios {
+		pinconf {
+			pins = "gpio8";
+			function = PMIC_GPIO_FUNC_NORMAL;
+			output-low;
+			power-source = <PM8994_GPIO_S4>; // 1.8V
+			qcom,drive-strength = <PMIC_GPIO_STRENGTH_LOW>;
+			bias-pull-down;
+		};
+	};
+
+	audio_mclk: clk_div1 {
+		pinconf {
+			pins = "gpio15";
+			function = "func1";
+			power-source = <PM8994_GPIO_S4>; // 1.8V
+		};
+	};
+
+	volume_up_gpio: pm8996_gpio2 {
+		pinconf {
+			pins = "gpio2";
+			function = "normal";
+			input-enable;
+			drive-push-pull;
+			bias-pull-up;
+			qcom,drive-strength = <PMIC_GPIO_STRENGTH_NO>;
+			power-source = <PM8994_GPIO_S4>; // 1.8V
+		};
+	};
+
+	divclk4_pin_a: divclk4 {
+		pinconf {
+			pins = "gpio18";
+			function = PMIC_GPIO_FUNC_FUNC2;
+
+			bias-disable;
+			power-source = <PM8994_GPIO_S4>;
+		};
+	};
+
+	usb3_vbus_det_gpio: pm8996_gpio22 {
+		pinconf {
+			pins = "gpio22";
+			function = PMIC_GPIO_FUNC_NORMAL;
+			input-enable;
+			bias-pull-down;
+			qcom,drive-strength = <PMIC_GPIO_STRENGTH_NO>;
+			power-source = <PM8994_GPIO_S4>; // 1.8V
+		};
+	};
+};
+
+&pm8994_mpps {
+	gpio-line-names =
+		"VDDPX_BIAS",
+		"WIFI_LED",
+		"NC",
+		"BT_LED",
+		"PM_MPP05",
+		"PM_MPP06",
+		"PM_MPP07",
+		"NC";
+};
+
+&pm8994_spmi_regulators {
+	qcom,saw-reg = <&saw3>;
+	s9 {
+		qcom,saw-slave;
+	};
+	s10 {
+		qcom,saw-slave;
+	};
+	s11 {
+		qcom,saw-leader;
+		regulator-always-on;
+		regulator-min-microvolt = <980000>;
+		regulator-max-microvolt = <980000>;
+	};
+};
+
+&pmi8994_gpios {
+	gpio-line-names =
+		"NC",
+		"SPKR_AMP_EN1",
+		"SPKR_AMP_EN2",
+		"TP61",
+		"NC",
+		"USB2_VBUS_DET",
+		"NC",
+		"NC",
+		"NC",
+		"NC";
+
+	usb2_vbus_det_gpio: pmi8996_gpio6 {
+		pinconf {
+			pins = "gpio6";
+			function = PMIC_GPIO_FUNC_NORMAL;
+			input-enable;
+			bias-pull-down;
+			qcom,drive-strength = <PMIC_GPIO_STRENGTH_NO>;
+			power-source = <PM8994_GPIO_S4>; // 1.8V
+		};
+	};
+};
+
+&pmi8994_spmi_regulators {
+	vdd_gfx: s2@1700 {
+		reg = <0x1700 0x100>;
+		regulator-name = "VDD_GFX";
+		regulator-min-microvolt = <980000>;
+		regulator-max-microvolt = <980000>;
+	};
+};
+
+&rpm_requests {
+	pm8994-regulators {
+		compatible = "qcom,rpm-pm8994-regulators";
+
+		vdd_s1-supply = <&vph_pwr>;
+		vdd_s2-supply = <&vph_pwr>;
+		vdd_s3-supply = <&vph_pwr>;
+		vdd_s4-supply = <&vph_pwr>;
+		vdd_s5-supply = <&vph_pwr>;
+		vdd_s6-supply = <&vph_pwr>;
+		vdd_s7-supply = <&vph_pwr>;
+		vdd_s8-supply = <&vph_pwr>;
+		vdd_s9-supply = <&vph_pwr>;
+		vdd_s10-supply = <&vph_pwr>;
+		vdd_s11-supply = <&vph_pwr>;
+		vdd_s12-supply = <&vph_pwr>;
+		vdd_l1-supply = <&vreg_s1b_1p025>;
+		vdd_l2_l26_l28-supply = <&vreg_s3a_1p3>;
+		vdd_l3_l11-supply = <&vreg_s3a_1p3>;
+		vdd_l4_l27_l31-supply = <&vreg_s3a_1p3>;
+		vdd_l5_l7-supply = <&vreg_s5a_2p15>;
+		vdd_l6_l12_l32-supply = <&vreg_s5a_2p15>;
+		vdd_l8_l16_l30-supply = <&vph_pwr>;
+		vdd_l9_l10_l18_l22-supply = <&vph_pwr_bbyp>;
+		vdd_l13_l19_l23_l24-supply = <&vph_pwr_bbyp>;
+		vdd_l14_l15-supply = <&vreg_s5a_2p15>;
+		vdd_l17_l29-supply = <&vph_pwr_bbyp>;
+		vdd_l20_l21-supply = <&vph_pwr_bbyp>;
+		vdd_l25-supply = <&vreg_s3a_1p3>;
+		vdd_lvs1_lvs2-supply = <&vreg_s4a_1p8>;
+
+		vreg_s3a_1p3: s3 {
+			regulator-name = "vreg_s3a_1p3";
+			regulator-min-microvolt = <1300000>;
+			regulator-max-microvolt = <1300000>;
+		};
+
+		/**
+		 * 1.8v required on LS expansion
+		 * for mezzanine boards
+		 */
+		vreg_s4a_1p8: s4 {
+			regulator-name = "vreg_s4a_1p8";
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			regulator-always-on;
+		};
+		vreg_s5a_2p15: s5 {
+			regulator-name = "vreg_s5a_2p15";
+			regulator-min-microvolt = <2150000>;
+			regulator-max-microvolt = <2150000>;
+		};
+		vreg_s7a_1p0: s7 {
+			regulator-name = "vreg_s7a_1p0";
+			regulator-min-microvolt = <800000>;
+			regulator-max-microvolt = <800000>;
+		};
+
+		vreg_l1a_1p0: l1 {
+			regulator-name = "vreg_l1a_1p0";
+			regulator-min-microvolt = <1000000>;
+			regulator-max-microvolt = <1000000>;
+		};
+		vreg_l2a_1p25: l2 {
+			regulator-name = "vreg_l2a_1p25";
+			regulator-min-microvolt = <1250000>;
+			regulator-max-microvolt = <1250000>;
+		};
+		vreg_l3a_0p875: l3 {
+			regulator-name = "vreg_l3a_0p875";
+			regulator-min-microvolt = <850000>;
+			regulator-max-microvolt = <850000>;
+		};
+		vreg_l4a_1p225: l4 {
+			regulator-name = "vreg_l4a_1p225";
+			regulator-min-microvolt = <1225000>;
+			regulator-max-microvolt = <1225000>;
+		};
+		vreg_l6a_1p2: l6 {
+			regulator-name = "vreg_l6a_1p2";
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1200000>;
+		};
+		vreg_l8a_1p8: l8 {
+			regulator-name = "vreg_l8a_1p8";
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+		};
+		vreg_l9a_1p8: l9 {
+			regulator-name = "vreg_l9a_1p8";
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+		};
+		vreg_l10a_1p8: l10 {
+			regulator-name = "vreg_l10a_1p8";
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+		};
+		vreg_l11a_1p15: l11 {
+			regulator-name = "vreg_l11a_1p15";
+			regulator-min-microvolt = <1150000>;
+			regulator-max-microvolt = <1150000>;
+		};
+		vreg_l12a_1p8: l12 {
+			regulator-name = "vreg_l12a_1p8";
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+		};
+		vreg_l13a_2p95: l13 {
+			regulator-name = "vreg_l13a_2p95";
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <2950000>;
+		};
+		vreg_l14a_1p8: l14 {
+			regulator-name = "vreg_l14a_1p8";
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+		};
+		vreg_l15a_1p8: l15 {
+			regulator-name = "vreg_l15a_1p8";
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+		};
+		vreg_l16a_2p7: l16 {
+			regulator-name = "vreg_l16a_2p7";
+			regulator-min-microvolt = <2700000>;
+			regulator-max-microvolt = <2700000>;
+		};
+		vreg_l17a_2p8: l17 {
+			regulator-name = "vreg_l17a_2p8";
+			regulator-min-microvolt = <2500000>;
+			regulator-max-microvolt = <2500000>;
+		};
+		vreg_l18a_2p85: l18 {
+			regulator-name = "vreg_l18a_2p85";
+			regulator-min-microvolt = <2700000>;
+			regulator-max-microvolt = <2900000>;
+		};
+		vreg_l19a_2p8: l19 {
+			regulator-name = "vreg_l19a_2p8";
+			regulator-min-microvolt = <3000000>;
+			regulator-max-microvolt = <3000000>;
+		};
+		vreg_l20a_2p95: l20 {
+			regulator-name = "vreg_l20a_2p95";
+			regulator-min-microvolt = <2950000>;
+			regulator-max-microvolt = <2950000>;
+			regulator-allow-set-load;
+		};
+		vreg_l21a_2p95: l21 {
+			regulator-name = "vreg_l21a_2p95";
+			regulator-min-microvolt = <2950000>;
+			regulator-max-microvolt = <2950000>;
+			regulator-allow-set-load;
+			regulator-system-load = <200000>;
+		};
+		vreg_l22a_3p0: l22 {
+			regulator-name = "vreg_l22a_3p0";
+			regulator-min-microvolt = <3300000>;
+			regulator-max-microvolt = <3300000>;
+		};
+		vreg_l23a_2p8: l23 {
+			regulator-name = "vreg_l23a_2p8";
+			regulator-min-microvolt = <2800000>;
+			regulator-max-microvolt = <2800000>;
+		};
+		vreg_l24a_3p075: l24 {
+			regulator-name = "vreg_l24a_3p075";
+			regulator-min-microvolt = <3075000>;
+			regulator-max-microvolt = <3075000>;
+		};
+		vreg_l25a_1p2: l25 {
+			regulator-name = "vreg_l25a_1p2";
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1200000>;
+			regulator-allow-set-load;
+		};
+		vreg_l26a_0p8: l27 {
+			regulator-name = "vreg_l26a_0p8";
+			regulator-min-microvolt = <1000000>;
+			regulator-max-microvolt = <1000000>;
+		};
+		vreg_l28a_0p925: l28 {
+			regulator-name = "vreg_l28a_0p925";
+			regulator-min-microvolt = <925000>;
+			regulator-max-microvolt = <925000>;
+			regulator-allow-set-load;
+		};
+		vreg_l29a_2p8: l29 {
+			regulator-name = "vreg_l29a_2p8";
+			regulator-min-microvolt = <2800000>;
+			regulator-max-microvolt = <2800000>;
+		};
+		vreg_l30a_1p8: l30 {
+			regulator-name = "vreg_l30a_1p8";
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+		};
+		vreg_l32a_1p8: l32 {
+			regulator-name = "vreg_l32a_1p8";
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+		};
+
+		vreg_lvs1a_1p8: lvs1 {
+			regulator-name = "vreg_lvs1a_1p8";
+		};
+
+		vreg_lvs2a_1p8: lvs2 {
+			regulator-name = "vreg_lvs2a_1p8";
+		};
+	};
+
+	pmi8994-regulators {
+		compatible = "qcom,rpm-pmi8994-regulators";
+
+		vdd_s1-supply = <&vph_pwr>;
+		vdd_s2-supply = <&vph_pwr>;
+		vdd_s3-supply = <&vph_pwr>;
+		vdd_bst_byp-supply = <&vph_pwr>;
+
+		vph_pwr_bbyp: boost-bypass {
+			regulator-name = "vph_pwr_bbyp";
+			regulator-min-microvolt = <3300000>;
+			regulator-max-microvolt = <3300000>;
+		};
+
+		vreg_s1b_1p025: s1 {
+			regulator-name = "vreg_s1b_1p025";
+			regulator-min-microvolt = <1025000>;
+			regulator-max-microvolt = <1025000>;
+		};
+	};
+};
+
+&sdhc2 {
+	/* External SD card */
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&sdc2_state_on &sdc2_cd_on>;
+	pinctrl-1 = <&sdc2_state_off &sdc2_cd_off>;
+	cd-gpios = <&tlmm 38 GPIO_ACTIVE_LOW>;
+	vmmc-supply = <&vreg_l21a_2p95>;
+	vqmmc-supply = <&vreg_l13a_2p95>;
+	status = "okay";
+};
+
+&q6asmdai {
+	dai@0 {
+		reg = <0>;
+	};
+
+	dai@1 {
+		reg = <1>;
+	};
+
+	dai@2 {
+		reg = <2>;
+	};
+};
+
+&sound {
+	compatible = "qcom,apq8096-sndcard";
+	model = "DB820c";
+	audio-routing =	"RX_BIAS", "MCLK",
+		"MM_DL1",  "MultiMedia1 Playback",
+		"MM_DL2",  "MultiMedia2 Playback",
+		"MultiMedia3 Capture", "MM_UL3";
+
+	mm1-dai-link {
+		link-name = "MultiMedia1";
+		cpu {
+			sound-dai = <&q6asmdai  MSM_FRONTEND_DAI_MULTIMEDIA1>;
+		};
+	};
+
+	mm2-dai-link {
+		link-name = "MultiMedia2";
+		cpu {
+			sound-dai = <&q6asmdai  MSM_FRONTEND_DAI_MULTIMEDIA2>;
+		};
+	};
+
+	mm3-dai-link {
+		link-name = "MultiMedia3";
+		cpu {
+			sound-dai = <&q6asmdai  MSM_FRONTEND_DAI_MULTIMEDIA3>;
+		};
+	};
+
+	hdmi-dai-link {
+		link-name = "HDMI";
+		cpu {
+			sound-dai = <&q6afedai HDMI_RX>;
+		};
+
+		platform {
+			sound-dai = <&q6routing>;
+		};
+
+		codec {
+			sound-dai = <&hdmi 0>;
+		};
+	};
+
+	slim-dai-link {
+		link-name = "SLIM Playback";
+		cpu {
+			sound-dai = <&q6afedai SLIMBUS_6_RX>;
+		};
+
+		platform {
+			sound-dai = <&q6routing>;
+	};
+
+		codec {
+			sound-dai = <&wcd9335 6>;
+		};
+	};
+
+	slimcap-dai-link {
+		link-name = "SLIM Capture";
+		cpu {
+			sound-dai = <&q6afedai SLIMBUS_0_TX>;
+		};
+
+		platform {
+			sound-dai = <&q6routing>;
+		};
+
+		codec {
+			sound-dai = <&wcd9335 1>;
+		};
+	};
+};
+
+&ufsphy {
+	status = "okay";
+
+	vdda-phy-supply = <&vreg_l28a_0p925>;
+	vdda-pll-supply = <&vreg_l12a_1p8>;
+	vddp-ref-clk-supply = <&vreg_l25a_1p2>;
+};
+
+&ufshc {
+	status = "okay";
+
+	vcc-supply = <&vreg_l20a_2p95>;
+	vccq-supply = <&vreg_l25a_1p2>;
+	vccq2-supply = <&vreg_s4a_1p8>;
+
+	vcc-max-microamp = <600000>;
+	vccq-max-microamp = <450000>;
+	vccq2-max-microamp = <450000>;
+};
+
+&usb2 {
+	status = "okay";
+	extcon = <&usb2_id>;
+
+	dwc3@7600000 {
+		extcon = <&usb2_id>;
+		dr_mode = "otg";
+		maximum-speed = "high-speed";
+	};
+};
+
+&usb3 {
+	status = "okay";
+	extcon = <&usb3_id>;
+
+	dwc3@6a00000 {
+		extcon = <&usb3_id>;
+		dr_mode = "otg";
+	};
+};
+
+&usb3phy {
+	status = "okay";
+
+	vdda-phy-supply = <&vreg_l28a_0p925>;
+	vdda-pll-supply = <&vreg_l12a_1p8>;
+
+};
+
+&venus {
+	status = "okay";
+};
+
+&wcd9335 {
+	clock-names = "mclk", "slimbus";
+	clocks = <&div1_mclk>,
+		 <&rpmcc RPM_SMD_BB_CLK1>;
+
+	vdd-buck-supply = <&vreg_s4a_1p8>;
+	vdd-buck-sido-supply = <&vreg_s4a_1p8>;
+	vdd-tx-supply = <&vreg_s4a_1p8>;
+	vdd-rx-supply = <&vreg_s4a_1p8>;
+	vdd-io-supply = <&vreg_s4a_1p8>;
 };
diff --git a/arch/arm64/boot/dts/qcom/apq8096-db820c.dtsi b/arch/arm64/boot/dts/qcom/apq8096-db820c.dtsi
deleted file mode 100644
index 51e17094d7b1..000000000000
--- a/arch/arm64/boot/dts/qcom/apq8096-db820c.dtsi
+++ /dev/null
@@ -1,1105 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0-only
-/*
- * Copyright (c) 2014-2016, The Linux Foundation. All rights reserved.
- */
-
-#include "msm8996.dtsi"
-#include "pm8994.dtsi"
-#include "pmi8994.dtsi"
-#include <dt-bindings/input/input.h>
-#include <dt-bindings/gpio/gpio.h>
-#include <dt-bindings/pinctrl/qcom,pmic-gpio.h>
-#include <dt-bindings/sound/qcom,q6afe.h>
-#include <dt-bindings/sound/qcom,q6asm.h>
-
-/*
- * GPIO name legend: proper name = the GPIO line is used as GPIO
- *         NC      = not connected (pin out but not routed from the chip to
- *                   anything the board)
- *         "[PER]" = pin is muxed for [peripheral] (not GPIO)
- *         LSEC    = Low Speed External Connector
- *         P HSEC  = Primary High Speed External Connector
- *         S HSEC  = Secondary High Speed External Connector
- *         J14     = Camera Connector
- *         TP      = Test Points
- *
- * Line names are taken from the schematic "DragonBoard 820c",
- * drawing no: LM25-P2751-1
- *
- * For the lines routed to the external connectors the
- * lines are named after the 96Boards CE Specification 1.0,
- * Appendix "Expansion Connector Signal Description".
- *
- * When the 96Board naming of a line and the schematic name of
- * the same line are in conflict, the 96Board specification
- * takes precedence, which means that the external UART on the
- * LSEC is named UART0 while the schematic and SoC names this
- * UART3. This is only for the informational lines i.e. "[FOO]",
- * the GPIO named lines "GPIO-A" thru "GPIO-L" are the only
- * ones actually used for GPIO.
- */
-
-/ {
-	aliases {
-		serial0 = &blsp2_uart2;
-		serial1 = &blsp2_uart3;
-		serial2 = &blsp1_uart2;
-		i2c0	= &blsp1_i2c3;
-		i2c1	= &blsp2_i2c1;
-		i2c2	= &blsp2_i2c1;
-		spi0	= &blsp1_spi1;
-		spi1	= &blsp2_spi6;
-	};
-
-	chosen {
-		stdout-path = "serial0:115200n8";
-	};
-
-	clocks {
-		compatible = "simple-bus";
-		divclk4: divclk4 {
-			compatible = "fixed-clock";
-			#clock-cells = <0>;
-			clock-frequency = <32768>;
-			clock-output-names = "divclk4";
-
-			pinctrl-names = "default";
-			pinctrl-0 = <&divclk4_pin_a>;
-		};
-
-		div1_mclk: divclk1 {
-			compatible = "gpio-gate-clock";
-			pinctrl-0 = <&audio_mclk>;
-			pinctrl-names = "default";
-			clocks = <&rpmcc RPM_SMD_DIV_CLK1>;
-			#clock-cells = <0>;
-			enable-gpios = <&pm8994_gpios 15 0>;
-		};
-	};
-
-	gpio_keys {
-		compatible = "gpio-keys";
-		#address-cells = <1>;
-		#size-cells = <0>;
-		autorepeat;
-
-		pinctrl-names = "default";
-		pinctrl-0 = <&volume_up_gpio>;
-
-		button@0 {
-			label = "Volume Up";
-			linux,code = <KEY_VOLUMEUP>;
-			gpios = <&pm8994_gpios 2 GPIO_ACTIVE_LOW>;
-		};
-	};
-
-	usb2_id: usb2-id {
-		compatible = "linux,extcon-usb-gpio";
-		id-gpio = <&pmi8994_gpios 6 GPIO_ACTIVE_HIGH>;
-		pinctrl-names = "default";
-		pinctrl-0 = <&usb2_vbus_det_gpio>;
-	};
-
-	usb3_id: usb3-id {
-		compatible = "linux,extcon-usb-gpio";
-		id-gpio = <&pm8994_gpios 22 GPIO_ACTIVE_HIGH>;
-		pinctrl-names = "default";
-		pinctrl-0 = <&usb3_vbus_det_gpio>;
-	};
-
-	vph_pwr: vph-pwr-regulator {
-		compatible = "regulator-fixed";
-		regulator-name = "vph_pwr";
-		regulator-always-on;
-		regulator-boot-on;
-
-		regulator-min-microvolt = <3700000>;
-		regulator-max-microvolt = <3700000>;
-	};
-
-	wlan_en: wlan-en-1-8v {
-		pinctrl-names = "default";
-		pinctrl-0 = <&wlan_en_gpios>;
-		compatible = "regulator-fixed";
-		regulator-name = "wlan-en-regulator";
-		regulator-min-microvolt = <1800000>;
-		regulator-max-microvolt = <1800000>;
-
-		gpio = <&pm8994_gpios 8 0>;
-
-		/* WLAN card specific delay */
-		startup-delay-us = <70000>;
-		enable-active-high;
-	};
-};
-
-&blsp1_i2c3 {
-	/* On Low speed expansion */
-	label = "LS-I2C0";
-	status = "okay";
-};
-
-&blsp1_spi1 {
-	/* On Low speed expansion */
-	label = "LS-SPI0";
-	status = "okay";
-};
-
-&blsp1_uart2 {
-	label = "BT-UART";
-	status = "okay";
-	pinctrl-names = "default", "sleep";
-	pinctrl-0 = <&blsp1_uart2_default>;
-	pinctrl-1 = <&blsp1_uart2_sleep>;
-
-	bluetooth {
-		compatible = "qcom,qca6174-bt";
-
-		/* bt_disable_n gpio */
-		enable-gpios = <&pm8994_gpios 19 GPIO_ACTIVE_HIGH>;
-
-		clocks = <&divclk4>;
-	};
-};
-
-&adsp_pil {
-	status = "okay";
-};
-
-&blsp2_i2c1 {
-	/* On High speed expansion */
-	label = "HS-I2C2";
-	status = "okay";
-};
-
-&blsp2_i2c1 {
-	/* On Low speed expansion */
-	label = "LS-I2C1";
-	status = "okay";
-};
-
-&blsp2_spi6 {
-	/* On High speed expansion */
-	label = "HS-SPI1";
-	status = "okay";
-};
-
-&blsp2_uart2 {
-	label = "LS-UART1";
-	status = "okay";
-	pinctrl-names = "default", "sleep";
-	pinctrl-0 = <&blsp2_uart2_2pins_default>;
-	pinctrl-1 = <&blsp2_uart2_2pins_sleep>;
-};
-
-&blsp2_uart3 {
-	label = "LS-UART0";
-	status = "disabled";
-	pinctrl-names = "default", "sleep";
-	pinctrl-0 = <&blsp2_uart3_4pins_default>;
-	pinctrl-1 = <&blsp2_uart3_4pins_sleep>;
-};
-
-&camss {
-	vdda-supply = <&vreg_l2a_1p25>;
-};
-
-&gpu {
-	status = "okay";
-};
-
-&hdmi {
-	status = "okay";
-
-	pinctrl-names = "default", "sleep";
-	pinctrl-0 = <&hdmi_hpd_active &hdmi_ddc_active>;
-	pinctrl-1 = <&hdmi_hpd_suspend &hdmi_ddc_suspend>;
-
-	core-vdda-supply = <&vreg_l12a_1p8>;
-	core-vcc-supply = <&vreg_s4a_1p8>;
-};
-
-&hdmi_phy {
-	status = "okay";
-
-	vddio-supply = <&vreg_l12a_1p8>;
-	vcca-supply = <&vreg_l28a_0p925>;
-	#phy-cells = <0>;
-};
-
-&hsusb_phy1 {
-	status = "okay";
-
-	vdda-pll-supply = <&vreg_l12a_1p8>;
-	vdda-phy-dpdm-supply = <&vreg_l24a_3p075>;
-};
-
-&hsusb_phy2 {
-	status = "okay";
-
-	vdda-pll-supply = <&vreg_l12a_1p8>;
-	vdda-phy-dpdm-supply = <&vreg_l24a_3p075>;
-};
-
-&mdp {
-	status = "okay";
-};
-
-&mdss {
-	status = "okay";
-};
-
-&mmcc {
-	vdd-gfx-supply = <&vdd_gfx>;
-};
-
-&pm8994_resin {
-	status = "okay";
-	linux,code = <KEY_VOLUMEDOWN>;
-};
-
-&tlmm {
-	gpio-line-names =
-		"[SPI0_DOUT]", /* GPIO_0, BLSP1_SPI_MOSI, LSEC pin 14 */
-		"[SPI0_DIN]", /* GPIO_1, BLSP1_SPI_MISO, LSEC pin 10 */
-		"[SPI0_CS]", /* GPIO_2, BLSP1_SPI_CS_N, LSEC pin 12 */
-		"[SPI0_SCLK]", /* GPIO_3, BLSP1_SPI_CLK, LSEC pin 8 */
-		"[UART1_TxD]", /* GPIO_4, BLSP8_UART_TX, LSEC pin 11 */
-		"[UART1_RxD]", /* GPIO_5, BLSP8_UART_RX, LSEC pin 13 */
-		"[I2C1_SDA]", /* GPIO_6, BLSP8_I2C_SDA, LSEC pin 21 */
-		"[I2C1_SCL]", /* GPIO_7, BLSP8_I2C_SCL, LSEC pin 19 */
-		"GPIO-H", /* GPIO_8, LCD0_RESET_N, LSEC pin 30 */
-		"TP93", /* GPIO_9 */
-		"GPIO-G", /* GPIO_10, MDP_VSYNC_P, LSEC pin 29 */
-		"[MDP_VSYNC_S]", /* GPIO_11, S HSEC pin 55 */
-		"NC", /* GPIO_12 */
-		"[CSI0_MCLK]", /* GPIO_13, CAM_MCLK0, P HSEC pin 15 */
-		"[CAM_MCLK1]", /* GPIO_14, J14 pin 11 */
-		"[CSI1_MCLK]", /* GPIO_15, CAM_MCLK2, P HSEC pin 17 */
-		"TP99", /* GPIO_16 */
-		"[I2C2_SDA]", /* GPIO_17, CCI_I2C_SDA0, P HSEC pin 34 */
-		"[I2C2_SCL]", /* GPIO_18, CCI_I2C_SCL0, P HSEC pin 32 */
-		"[CCI_I2C_SDA1]", /* GPIO_19, S HSEC pin 38 */
-		"[CCI_I2C_SCL1]", /* GPIO_20, S HSEC pin 36 */
-		"FLASH_STROBE_EN", /* GPIO_21, S HSEC pin 5 */
-		"FLASH_STROBE_TRIG", /* GPIO_22, S HSEC pin 1 */
-		"GPIO-K", /* GPIO_23, CAM2_RST_N, LSEC pin 33 */
-		"GPIO-D", /* GPIO_24, LSEC pin 26 */
-		"GPIO-I", /* GPIO_25, CAM0_RST_N, LSEC pin 31 */
-		"GPIO-J", /* GPIO_26, CAM0_STANDBY_N, LSEC pin 32 */
-		"BLSP6_I2C_SDA", /* GPIO_27 */
-		"BLSP6_I2C_SCL", /* GPIO_28 */
-		"GPIO-B", /* GPIO_29, TS0_RESET_N, LSEC pin 24 */
-		"GPIO30", /* GPIO_30, S HSEC pin 4 */
-		"HDMI_CEC", /* GPIO_31 */
-		"HDMI_DDC_CLOCK", /* GPIO_32 */
-		"HDMI_DDC_DATA", /* GPIO_33 */
-		"HDMI_HOT_PLUG_DETECT", /* GPIO_34 */
-		"PCIE0_RST_N", /* GPIO_35 */
-		"PCIE0_CLKREQ_N", /* GPIO_36 */
-		"PCIE0_WAKE", /* GPIO_37 */
-		"SD_CARD_DET_N", /* GPIO_38 */
-		"TSIF1_SYNC", /* GPIO_39, S HSEC pin 48 */
-		"W_DISABLE_N", /* GPIO_40 */
-		"[BLSP9_UART_TX]", /* GPIO_41 */
-		"[BLSP9_UART_RX]", /* GPIO_42 */
-		"[BLSP2_UART_CTS_N]", /* GPIO_43 */
-		"[BLSP2_UART_RFR_N]", /* GPIO_44 */
-		"[BLSP3_UART_TX]", /* GPIO_45 */
-		"[BLSP3_UART_RX]", /* GPIO_46 */
-		"[I2C0_SDA]", /* GPIO_47, LS_I2C0_SDA, LSEC pin 17 */
-		"[I2C0_SCL]", /* GPIO_48, LS_I2C0_SCL, LSEC pin 15 */
-		"[UART0_TxD]", /* GPIO_49, BLSP9_UART_TX, LSEC pin 5 */
-		"[UART0_RxD]", /* GPIO_50, BLSP9_UART_RX, LSEC pin 7 */
-		"[UART0_CTS]", /* GPIO_51, BLSP9_UART_CTS_N, LSEC pin 3 */
-		"[UART0_RTS]", /* GPIO_52, BLSP9_UART_RFR_N, LSEC pin 9 */
-		"[CODEC_INT1_N]", /* GPIO_53 */
-		"[CODEC_INT2_N]", /* GPIO_54 */
-		"[BLSP7_I2C_SDA]", /* GPIO_55 */
-		"[BLSP7_I2C_SCL]", /* GPIO_56 */
-		"MI2S_MCLK", /* GPIO_57, S HSEC pin 3 */
-		"[PCM_CLK]", /* GPIO_58, QUA_MI2S_SCK, LSEC pin 18 */
-		"[PCM_FS]", /* GPIO_59, QUA_MI2S_WS, LSEC pin 16 */
-		"[PCM_DO]", /* GPIO_60, QUA_MI2S_DATA0, LSEC pin 20 */
-		"[PCM_DI]", /* GPIO_61, QUA_MI2S_DATA1, LSEC pin 22 */
-		"GPIO-E", /* GPIO_62, LSEC pin 27 */
-		"TP87", /* GPIO_63 */
-		"[CODEC_RST_N]", /* GPIO_64 */
-		"[PCM1_CLK]", /* GPIO_65 */
-		"[PCM1_SYNC]", /* GPIO_66 */
-		"[PCM1_DIN]", /* GPIO_67 */
-		"[PCM1_DOUT]", /* GPIO_68 */
-		"AUDIO_REF_CLK", /* GPIO_69 */
-		"SLIMBUS_CLK", /* GPIO_70 */
-		"SLIMBUS_DATA0", /* GPIO_71 */
-		"SLIMBUS_DATA1", /* GPIO_72 */
-		"NC", /* GPIO_73 */
-		"NC", /* GPIO_74 */
-		"NC", /* GPIO_75 */
-		"NC", /* GPIO_76 */
-		"TP94", /* GPIO_77 */
-		"NC", /* GPIO_78 */
-		"TP95", /* GPIO_79 */
-		"GPIO-A", /* GPIO_80, MEMS_RESET_N, LSEC pin 23 */
-		"TP88", /* GPIO_81 */
-		"TP89", /* GPIO_82 */
-		"TP90", /* GPIO_83 */
-		"TP91", /* GPIO_84 */
-		"[SD_DAT0]", /* GPIO_85, BLSP12_SPI_MOSI, P HSEC pin 1 */
-		"[SD_CMD]", /* GPIO_86, BLSP12_SPI_MISO, P HSEC pin 11 */
-		"[SD_DAT3]", /* GPIO_87, BLSP12_SPI_CS_N, P HSEC pin 7 */
-		"[SD_SCLK]", /* GPIO_88, BLSP12_SPI_CLK, P HSEC pin 9 */
-		"TSIF1_CLK", /* GPIO_89, S HSEC pin 42 */
-		"TSIF1_EN", /* GPIO_90, S HSEC pin 46 */
-		"TSIF1_DATA", /* GPIO_91, S HSEC pin 44 */
-		"NC", /* GPIO_92 */
-		"TSIF2_CLK", /* GPIO_93, S HSEC pin 52 */
-		"TSIF2_EN", /* GPIO_94, S HSEC pin 56 */
-		"TSIF2_DATA", /* GPIO_95, S HSEC pin 54 */
-		"TSIF2_SYNC", /* GPIO_96, S HSEC pin 58 */
-		"NC", /* GPIO_97 */
-		"CAM1_STANDBY_N", /* GPIO_98 */
-		"NC", /* GPIO_99 */
-		"NC", /* GPIO_100 */
-		"[LCD1_RESET_N]", /* GPIO_101, S HSEC pin 51 */
-		"BOOT_CONFIG1", /* GPIO_102 */
-		"USB_HUB_RESET", /* GPIO_103 */
-		"CAM1_RST_N", /* GPIO_104 */
-		"NC", /* GPIO_105 */
-		"NC", /* GPIO_106 */
-		"NC", /* GPIO_107 */
-		"NC", /* GPIO_108 */
-		"NC", /* GPIO_109 */
-		"NC", /* GPIO_110 */
-		"NC", /* GPIO_111 */
-		"NC", /* GPIO_112 */
-		"PMI8994_BUA", /* GPIO_113 */
-		"PCIE2_RST_N", /* GPIO_114 */
-		"PCIE2_CLKREQ_N", /* GPIO_115 */
-		"PCIE2_WAKE", /* GPIO_116 */
-		"SSC_IRQ_0", /* GPIO_117 */
-		"SSC_IRQ_1", /* GPIO_118 */
-		"SSC_IRQ_2", /* GPIO_119 */
-		"NC", /* GPIO_120 */
-		"GPIO121", /* GPIO_121, S HSEC pin 2 */
-		"NC", /* GPIO_122 */
-		"SSC_IRQ_6", /* GPIO_123 */
-		"SSC_IRQ_7", /* GPIO_124 */
-		"GPIO-C", /* GPIO_125, TS_INT0, LSEC pin 25 */
-		"BOOT_CONFIG5", /* GPIO_126 */
-		"NC", /* GPIO_127 */
-		"NC", /* GPIO_128 */
-		"BOOT_CONFIG7", /* GPIO_129 */
-		"PCIE1_RST_N", /* GPIO_130 */
-		"PCIE1_CLKREQ_N", /* GPIO_131 */
-		"PCIE1_WAKE", /* GPIO_132 */
-		"GPIO-L", /* GPIO_133, CAM2_STANDBY_N, LSEC pin 34 */
-		"NC", /* GPIO_134 */
-		"NC", /* GPIO_135 */
-		"BOOT_CONFIG8", /* GPIO_136 */
-		"NC", /* GPIO_137 */
-		"NC", /* GPIO_138 */
-		"GPS_SSBI2", /* GPIO_139 */
-		"GPS_SSBI1", /* GPIO_140 */
-		"NC", /* GPIO_141 */
-		"NC", /* GPIO_142 */
-		"NC", /* GPIO_143 */
-		"BOOT_CONFIG6", /* GPIO_144 */
-		"NC", /* GPIO_145 */
-		"NC", /* GPIO_146 */
-		"NC", /* GPIO_147 */
-		"NC", /* GPIO_148 */
-		"NC"; /* GPIO_149 */
-
-	sdc2_cd_on: sdc2_cd_on {
-		mux {
-			pins = "gpio38";
-			function = "gpio";
-		};
-
-		config {
-			pins = "gpio38";
-			bias-pull-up;		/* pull up */
-			drive-strength = <16>;	/* 16 MA */
-		};
-	};
-
-	sdc2_cd_off: sdc2_cd_off {
-		mux {
-			pins = "gpio38";
-			function = "gpio";
-		};
-
-		config {
-			pins = "gpio38";
-			bias-pull-up;		/* pull up */
-			drive-strength = <2>;	/* 2 MA */
-		};
-	};
-
-	blsp1_uart2_default: blsp1_uart2_default {
-		mux {
-			pins = "gpio41", "gpio42", "gpio43", "gpio44";
-			function = "blsp_uart2";
-		};
-
-		config {
-			pins = "gpio41", "gpio42", "gpio43", "gpio44";
-			drive-strength = <16>;
-			bias-disable;
-		};
-	};
-
-	blsp1_uart2_sleep: blsp1_uart2_sleep {
-		mux {
-			pins = "gpio41", "gpio42", "gpio43", "gpio44";
-			function = "gpio";
-		};
-
-		config {
-			pins = "gpio41", "gpio42", "gpio43", "gpio44";
-			drive-strength = <2>;
-			bias-disable;
-		};
-	};
-
-	hdmi_hpd_active: hdmi_hpd_active {
-		mux {
-			pins = "gpio34";
-			function = "hdmi_hot";
-		};
-
-		config {
-			pins = "gpio34";
-			bias-pull-down;
-			drive-strength = <16>;
-		};
-	};
-
-	hdmi_hpd_suspend: hdmi_hpd_suspend {
-		mux {
-			pins = "gpio34";
-			function = "hdmi_hot";
-		};
-
-		config {
-			pins = "gpio34";
-			bias-pull-down;
-			drive-strength = <2>;
-		};
-	};
-
-	hdmi_ddc_active: hdmi_ddc_active {
-		mux {
-			pins = "gpio32", "gpio33";
-			function = "hdmi_ddc";
-		};
-
-		config {
-			pins = "gpio32", "gpio33";
-			drive-strength = <2>;
-			bias-pull-up;
-		};
-	};
-
-	hdmi_ddc_suspend: hdmi_ddc_suspend {
-		mux {
-			pins = "gpio32", "gpio33";
-			function = "hdmi_ddc";
-		};
-
-		config {
-			pins = "gpio32", "gpio33";
-			drive-strength = <2>;
-			bias-pull-down;
-		};
-	};
-};
-
-&pcie0 {
-	status = "okay";
-	perst-gpio = <&tlmm 35 GPIO_ACTIVE_LOW>;
-	vddpe-3v3-supply = <&wlan_en>;
-	vdda-supply = <&vreg_l28a_0p925>;
-};
-
-&pcie1 {
-	status = "okay";
-	perst-gpio = <&tlmm 130 GPIO_ACTIVE_LOW>;
-	vdda-supply = <&vreg_l28a_0p925>;
-};
-
-&pcie2 {
-	status = "okay";
-	perst-gpio = <&tlmm 114 GPIO_ACTIVE_LOW>;
-	vdda-supply = <&vreg_l28a_0p925>;
-};
-
-&pcie_phy {
-	status = "okay";
-
-	vdda-phy-supply = <&vreg_l28a_0p925>;
-	vdda-pll-supply = <&vreg_l12a_1p8>;
-};
-
-&pm8994_gpios {
-	gpio-line-names =
-		"NC",
-		"KEY_VOLP_N",
-		"NC",
-		"BL1_PWM",
-		"GPIO-F", /* BL0_PWM, LSEC pin 28 */
-		"BL1_EN",
-		"NC",
-		"WLAN_EN",
-		"NC",
-		"NC",
-		"NC",
-		"NC",
-		"NC",
-		"NC",
-		"DIVCLK1",
-		"DIVCLK2",
-		"DIVCLK3",
-		"DIVCLK4",
-		"BT_EN",
-		"PMIC_SLB",
-		"PMIC_BUA",
-		"USB_VBUS_DET";
-
-	pinctrl-names = "default";
-	pinctrl-0 = <&ls_exp_gpio_f &bt_en_gpios>;
-
-	ls_exp_gpio_f: pm8994_gpio5 {
-		pinconf {
-			pins = "gpio5";
-			output-low;
-			power-source = <2>; // PM8994_GPIO_S4, 1.8V
-		};
-	};
-
-	bt_en_gpios: bt_en_gpios {
-		pinconf {
-			pins = "gpio19";
-			function = PMIC_GPIO_FUNC_NORMAL;
-			output-low;
-			power-source = <PM8994_GPIO_S4>; // 1.8V
-			qcom,drive-strength = <PMIC_GPIO_STRENGTH_LOW>;
-			bias-pull-down;
-		};
-	};
-
-	wlan_en_gpios: wlan_en_gpios {
-		pinconf {
-			pins = "gpio8";
-			function = PMIC_GPIO_FUNC_NORMAL;
-			output-low;
-			power-source = <PM8994_GPIO_S4>; // 1.8V
-			qcom,drive-strength = <PMIC_GPIO_STRENGTH_LOW>;
-			bias-pull-down;
-		};
-	};
-
-	audio_mclk: clk_div1 {
-		pinconf {
-			pins = "gpio15";
-			function = "func1";
-			power-source = <PM8994_GPIO_S4>; // 1.8V
-		};
-	};
-
-	volume_up_gpio: pm8996_gpio2 {
-		pinconf {
-			pins = "gpio2";
-			function = "normal";
-			input-enable;
-			drive-push-pull;
-			bias-pull-up;
-			qcom,drive-strength = <PMIC_GPIO_STRENGTH_NO>;
-			power-source = <PM8994_GPIO_S4>; // 1.8V
-		};
-	};
-
-	divclk4_pin_a: divclk4 {
-		pinconf {
-			pins = "gpio18";
-			function = PMIC_GPIO_FUNC_FUNC2;
-
-			bias-disable;
-			power-source = <PM8994_GPIO_S4>;
-		};
-	};
-
-	usb3_vbus_det_gpio: pm8996_gpio22 {
-		pinconf {
-			pins = "gpio22";
-			function = PMIC_GPIO_FUNC_NORMAL;
-			input-enable;
-			bias-pull-down;
-			qcom,drive-strength = <PMIC_GPIO_STRENGTH_NO>;
-			power-source = <PM8994_GPIO_S4>; // 1.8V
-		};
-	};
-};
-
-&pm8994_mpps {
-	gpio-line-names =
-		"VDDPX_BIAS",
-		"WIFI_LED",
-		"NC",
-		"BT_LED",
-		"PM_MPP05",
-		"PM_MPP06",
-		"PM_MPP07",
-		"NC";
-};
-
-&pm8994_spmi_regulators {
-	qcom,saw-reg = <&saw3>;
-	s9 {
-		qcom,saw-slave;
-	};
-	s10 {
-		qcom,saw-slave;
-	};
-	s11 {
-		qcom,saw-leader;
-		regulator-always-on;
-		regulator-min-microvolt = <980000>;
-		regulator-max-microvolt = <980000>;
-	};
-};
-
-&pmi8994_gpios {
-	gpio-line-names =
-		"NC",
-		"SPKR_AMP_EN1",
-		"SPKR_AMP_EN2",
-		"TP61",
-		"NC",
-		"USB2_VBUS_DET",
-		"NC",
-		"NC",
-		"NC",
-		"NC";
-
-	usb2_vbus_det_gpio: pmi8996_gpio6 {
-		pinconf {
-			pins = "gpio6";
-			function = PMIC_GPIO_FUNC_NORMAL;
-			input-enable;
-			bias-pull-down;
-			qcom,drive-strength = <PMIC_GPIO_STRENGTH_NO>;
-			power-source = <PM8994_GPIO_S4>; // 1.8V
-		};
-	};
-};
-
-&pmi8994_spmi_regulators {
-	vdd_gfx: s2@1700 {
-		reg = <0x1700 0x100>;
-		regulator-name = "VDD_GFX";
-		regulator-min-microvolt = <980000>;
-		regulator-max-microvolt = <980000>;
-	};
-};
-
-&rpm_requests {
-	pm8994-regulators {
-		compatible = "qcom,rpm-pm8994-regulators";
-
-		vdd_s1-supply = <&vph_pwr>;
-		vdd_s2-supply = <&vph_pwr>;
-		vdd_s3-supply = <&vph_pwr>;
-		vdd_s4-supply = <&vph_pwr>;
-		vdd_s5-supply = <&vph_pwr>;
-		vdd_s6-supply = <&vph_pwr>;
-		vdd_s7-supply = <&vph_pwr>;
-		vdd_s8-supply = <&vph_pwr>;
-		vdd_s9-supply = <&vph_pwr>;
-		vdd_s10-supply = <&vph_pwr>;
-		vdd_s11-supply = <&vph_pwr>;
-		vdd_s12-supply = <&vph_pwr>;
-		vdd_l1-supply = <&vreg_s1b_1p025>;
-		vdd_l2_l26_l28-supply = <&vreg_s3a_1p3>;
-		vdd_l3_l11-supply = <&vreg_s3a_1p3>;
-		vdd_l4_l27_l31-supply = <&vreg_s3a_1p3>;
-		vdd_l5_l7-supply = <&vreg_s5a_2p15>;
-		vdd_l6_l12_l32-supply = <&vreg_s5a_2p15>;
-		vdd_l8_l16_l30-supply = <&vph_pwr>;
-		vdd_l9_l10_l18_l22-supply = <&vph_pwr_bbyp>;
-		vdd_l13_l19_l23_l24-supply = <&vph_pwr_bbyp>;
-		vdd_l14_l15-supply = <&vreg_s5a_2p15>;
-		vdd_l17_l29-supply = <&vph_pwr_bbyp>;
-		vdd_l20_l21-supply = <&vph_pwr_bbyp>;
-		vdd_l25-supply = <&vreg_s3a_1p3>;
-		vdd_lvs1_lvs2-supply = <&vreg_s4a_1p8>;
-
-		vreg_s3a_1p3: s3 {
-			regulator-name = "vreg_s3a_1p3";
-			regulator-min-microvolt = <1300000>;
-			regulator-max-microvolt = <1300000>;
-		};
-
-		/**
-		 * 1.8v required on LS expansion
-		 * for mezzanine boards
-		 */
-		vreg_s4a_1p8: s4 {
-			regulator-name = "vreg_s4a_1p8";
-			regulator-min-microvolt = <1800000>;
-			regulator-max-microvolt = <1800000>;
-			regulator-always-on;
-		};
-		vreg_s5a_2p15: s5 {
-			regulator-name = "vreg_s5a_2p15";
-			regulator-min-microvolt = <2150000>;
-			regulator-max-microvolt = <2150000>;
-		};
-		vreg_s7a_1p0: s7 {
-			regulator-name = "vreg_s7a_1p0";
-			regulator-min-microvolt = <800000>;
-			regulator-max-microvolt = <800000>;
-		};
-
-		vreg_l1a_1p0: l1 {
-			regulator-name = "vreg_l1a_1p0";
-			regulator-min-microvolt = <1000000>;
-			regulator-max-microvolt = <1000000>;
-		};
-		vreg_l2a_1p25: l2 {
-			regulator-name = "vreg_l2a_1p25";
-			regulator-min-microvolt = <1250000>;
-			regulator-max-microvolt = <1250000>;
-		};
-		vreg_l3a_0p875: l3 {
-			regulator-name = "vreg_l3a_0p875";
-			regulator-min-microvolt = <850000>;
-			regulator-max-microvolt = <850000>;
-		};
-		vreg_l4a_1p225: l4 {
-			regulator-name = "vreg_l4a_1p225";
-			regulator-min-microvolt = <1225000>;
-			regulator-max-microvolt = <1225000>;
-		};
-		vreg_l6a_1p2: l6 {
-			regulator-name = "vreg_l6a_1p2";
-			regulator-min-microvolt = <1200000>;
-			regulator-max-microvolt = <1200000>;
-		};
-		vreg_l8a_1p8: l8 {
-			regulator-name = "vreg_l8a_1p8";
-			regulator-min-microvolt = <1800000>;
-			regulator-max-microvolt = <1800000>;
-		};
-		vreg_l9a_1p8: l9 {
-			regulator-name = "vreg_l9a_1p8";
-			regulator-min-microvolt = <1800000>;
-			regulator-max-microvolt = <1800000>;
-		};
-		vreg_l10a_1p8: l10 {
-			regulator-name = "vreg_l10a_1p8";
-			regulator-min-microvolt = <1800000>;
-			regulator-max-microvolt = <1800000>;
-		};
-		vreg_l11a_1p15: l11 {
-			regulator-name = "vreg_l11a_1p15";
-			regulator-min-microvolt = <1150000>;
-			regulator-max-microvolt = <1150000>;
-		};
-		vreg_l12a_1p8: l12 {
-			regulator-name = "vreg_l12a_1p8";
-			regulator-min-microvolt = <1800000>;
-			regulator-max-microvolt = <1800000>;
-		};
-		vreg_l13a_2p95: l13 {
-			regulator-name = "vreg_l13a_2p95";
-			regulator-min-microvolt = <1800000>;
-			regulator-max-microvolt = <2950000>;
-		};
-		vreg_l14a_1p8: l14 {
-			regulator-name = "vreg_l14a_1p8";
-			regulator-min-microvolt = <1800000>;
-			regulator-max-microvolt = <1800000>;
-		};
-		vreg_l15a_1p8: l15 {
-			regulator-name = "vreg_l15a_1p8";
-			regulator-min-microvolt = <1800000>;
-			regulator-max-microvolt = <1800000>;
-		};
-		vreg_l16a_2p7: l16 {
-			regulator-name = "vreg_l16a_2p7";
-			regulator-min-microvolt = <2700000>;
-			regulator-max-microvolt = <2700000>;
-		};
-		vreg_l17a_2p8: l17 {
-			regulator-name = "vreg_l17a_2p8";
-			regulator-min-microvolt = <2500000>;
-			regulator-max-microvolt = <2500000>;
-		};
-		vreg_l18a_2p85: l18 {
-			regulator-name = "vreg_l18a_2p85";
-			regulator-min-microvolt = <2700000>;
-			regulator-max-microvolt = <2900000>;
-		};
-		vreg_l19a_2p8: l19 {
-			regulator-name = "vreg_l19a_2p8";
-			regulator-min-microvolt = <3000000>;
-			regulator-max-microvolt = <3000000>;
-		};
-		vreg_l20a_2p95: l20 {
-			regulator-name = "vreg_l20a_2p95";
-			regulator-min-microvolt = <2950000>;
-			regulator-max-microvolt = <2950000>;
-			regulator-allow-set-load;
-		};
-		vreg_l21a_2p95: l21 {
-			regulator-name = "vreg_l21a_2p95";
-			regulator-min-microvolt = <2950000>;
-			regulator-max-microvolt = <2950000>;
-			regulator-allow-set-load;
-			regulator-system-load = <200000>;
-		};
-		vreg_l22a_3p0: l22 {
-			regulator-name = "vreg_l22a_3p0";
-			regulator-min-microvolt = <3300000>;
-			regulator-max-microvolt = <3300000>;
-		};
-		vreg_l23a_2p8: l23 {
-			regulator-name = "vreg_l23a_2p8";
-			regulator-min-microvolt = <2800000>;
-			regulator-max-microvolt = <2800000>;
-		};
-		vreg_l24a_3p075: l24 {
-			regulator-name = "vreg_l24a_3p075";
-			regulator-min-microvolt = <3075000>;
-			regulator-max-microvolt = <3075000>;
-		};
-		vreg_l25a_1p2: l25 {
-			regulator-name = "vreg_l25a_1p2";
-			regulator-min-microvolt = <1200000>;
-			regulator-max-microvolt = <1200000>;
-			regulator-allow-set-load;
-		};
-		vreg_l26a_0p8: l27 {
-			regulator-name = "vreg_l26a_0p8";
-			regulator-min-microvolt = <1000000>;
-			regulator-max-microvolt = <1000000>;
-		};
-		vreg_l28a_0p925: l28 {
-			regulator-name = "vreg_l28a_0p925";
-			regulator-min-microvolt = <925000>;
-			regulator-max-microvolt = <925000>;
-			regulator-allow-set-load;
-		};
-		vreg_l29a_2p8: l29 {
-			regulator-name = "vreg_l29a_2p8";
-			regulator-min-microvolt = <2800000>;
-			regulator-max-microvolt = <2800000>;
-		};
-		vreg_l30a_1p8: l30 {
-			regulator-name = "vreg_l30a_1p8";
-			regulator-min-microvolt = <1800000>;
-			regulator-max-microvolt = <1800000>;
-		};
-		vreg_l32a_1p8: l32 {
-			regulator-name = "vreg_l32a_1p8";
-			regulator-min-microvolt = <1800000>;
-			regulator-max-microvolt = <1800000>;
-		};
-
-		vreg_lvs1a_1p8: lvs1 {
-			regulator-name = "vreg_lvs1a_1p8";
-		};
-
-		vreg_lvs2a_1p8: lvs2 {
-			regulator-name = "vreg_lvs2a_1p8";
-		};
-	};
-
-	pmi8994-regulators {
-		compatible = "qcom,rpm-pmi8994-regulators";
-
-		vdd_s1-supply = <&vph_pwr>;
-		vdd_s2-supply = <&vph_pwr>;
-		vdd_s3-supply = <&vph_pwr>;
-		vdd_bst_byp-supply = <&vph_pwr>;
-
-		vph_pwr_bbyp: boost-bypass {
-			regulator-name = "vph_pwr_bbyp";
-			regulator-min-microvolt = <3300000>;
-			regulator-max-microvolt = <3300000>;
-		};
-
-		vreg_s1b_1p025: s1 {
-			regulator-name = "vreg_s1b_1p025";
-			regulator-min-microvolt = <1025000>;
-			regulator-max-microvolt = <1025000>;
-		};
-	};
-};
-
-&sdhc2 {
-	/* External SD card */
-	pinctrl-names = "default", "sleep";
-	pinctrl-0 = <&sdc2_state_on &sdc2_cd_on>;
-	pinctrl-1 = <&sdc2_state_off &sdc2_cd_off>;
-	cd-gpios = <&tlmm 38 GPIO_ACTIVE_LOW>;
-	vmmc-supply = <&vreg_l21a_2p95>;
-	vqmmc-supply = <&vreg_l13a_2p95>;
-	status = "okay";
-};
-
-&q6asmdai {
-	dai@0 {
-		reg = <0>;
-	};
-
-	dai@1 {
-		reg = <1>;
-	};
-
-	dai@2 {
-		reg = <2>;
-	};
-};
-
-&sound {
-	compatible = "qcom,apq8096-sndcard";
-	model = "DB820c";
-	audio-routing =	"RX_BIAS", "MCLK",
-		"MM_DL1",  "MultiMedia1 Playback",
-		"MM_DL2",  "MultiMedia2 Playback",
-		"MultiMedia3 Capture", "MM_UL3";
-
-	mm1-dai-link {
-		link-name = "MultiMedia1";
-		cpu {
-			sound-dai = <&q6asmdai  MSM_FRONTEND_DAI_MULTIMEDIA1>;
-		};
-	};
-
-	mm2-dai-link {
-		link-name = "MultiMedia2";
-		cpu {
-			sound-dai = <&q6asmdai  MSM_FRONTEND_DAI_MULTIMEDIA2>;
-		};
-	};
-
-	mm3-dai-link {
-		link-name = "MultiMedia3";
-		cpu {
-			sound-dai = <&q6asmdai  MSM_FRONTEND_DAI_MULTIMEDIA3>;
-		};
-	};
-
-	hdmi-dai-link {
-		link-name = "HDMI";
-		cpu {
-			sound-dai = <&q6afedai HDMI_RX>;
-		};
-
-		platform {
-			sound-dai = <&q6routing>;
-		};
-
-		codec {
-			sound-dai = <&hdmi 0>;
-		};
-	};
-
-	slim-dai-link {
-		link-name = "SLIM Playback";
-		cpu {
-			sound-dai = <&q6afedai SLIMBUS_6_RX>;
-		};
-
-		platform {
-			sound-dai = <&q6routing>;
-	};
-
-		codec {
-			sound-dai = <&wcd9335 6>;
-		};
-	};
-
-	slimcap-dai-link {
-		link-name = "SLIM Capture";
-		cpu {
-			sound-dai = <&q6afedai SLIMBUS_0_TX>;
-		};
-
-		platform {
-			sound-dai = <&q6routing>;
-		};
-
-		codec {
-			sound-dai = <&wcd9335 1>;
-		};
-	};
-};
-
-&ufsphy {
-	status = "okay";
-
-	vdda-phy-supply = <&vreg_l28a_0p925>;
-	vdda-pll-supply = <&vreg_l12a_1p8>;
-	vddp-ref-clk-supply = <&vreg_l25a_1p2>;
-};
-
-&ufshc {
-	status = "okay";
-
-	vcc-supply = <&vreg_l20a_2p95>;
-	vccq-supply = <&vreg_l25a_1p2>;
-	vccq2-supply = <&vreg_s4a_1p8>;
-
-	vcc-max-microamp = <600000>;
-	vccq-max-microamp = <450000>;
-	vccq2-max-microamp = <450000>;
-};
-
-&usb2 {
-	status = "okay";
-	extcon = <&usb2_id>;
-
-	dwc3@7600000 {
-		extcon = <&usb2_id>;
-		dr_mode = "otg";
-		maximum-speed = "high-speed";
-	};
-};
-
-&usb3 {
-	status = "okay";
-	extcon = <&usb3_id>;
-
-	dwc3@6a00000 {
-		extcon = <&usb3_id>;
-		dr_mode = "otg";
-	};
-};
-
-&usb3phy {
-	status = "okay";
-
-	vdda-phy-supply = <&vreg_l28a_0p925>;
-	vdda-pll-supply = <&vreg_l12a_1p8>;
-
-};
-
-&venus {
-	status = "okay";
-};
-
-&wcd9335 {
-	clock-names = "mclk", "slimbus";
-	clocks = <&div1_mclk>,
-		 <&rpmcc RPM_SMD_BB_CLK1>;
-
-	vdd-buck-supply = <&vreg_s4a_1p8>;
-	vdd-buck-sido-supply = <&vreg_s4a_1p8>;
-	vdd-tx-supply = <&vreg_s4a_1p8>;
-	vdd-rx-supply = <&vreg_s4a_1p8>;
-	vdd-io-supply = <&vreg_s4a_1p8>;
-};
diff --git a/arch/arm64/boot/dts/qcom/apq8096-ifc6640.dts b/arch/arm64/boot/dts/qcom/apq8096-ifc6640.dts
index a57c60070cdc..567b33106556 100644
--- a/arch/arm64/boot/dts/qcom/apq8096-ifc6640.dts
+++ b/arch/arm64/boot/dts/qcom/apq8096-ifc6640.dts
@@ -395,9 +395,6 @@
 
 	vdda-phy-supply = <&vreg_l28a_0p925>;
 	vdda-pll-supply = <&vreg_l12a_1p8>;
-
-	vdda-phy-max-microamp = <18380>;
-	vdda-pll-max-microamp = <9440>;
 };
 
 &venus {
diff --git a/arch/arm64/boot/dts/qcom/ipq6018.dtsi b/arch/arm64/boot/dts/qcom/ipq6018.dtsi
index d2fe58e0eb7a..933b56103a46 100644
--- a/arch/arm64/boot/dts/qcom/ipq6018.dtsi
+++ b/arch/arm64/boot/dts/qcom/ipq6018.dtsi
@@ -200,8 +200,7 @@
 			clock-names = "bam_clk";
 			#dma-cells = <1>;
 			qcom,ee = <1>;
-			qcom,controlled-remotely = <1>;
-			qcom,config-pipe-trust-reg = <0>;
+			qcom,controlled-remotely;
 		};
 
 		crypto: crypto@73a000 {
@@ -347,9 +346,8 @@
 			compatible = "qcom,bam-v1.7.0";
 			reg = <0x0 0x07984000 0x0 0x1a000>;
 			interrupts = <GIC_SPI 146 IRQ_TYPE_LEVEL_HIGH>;
-			clocks = <&gcc GCC_QPIC_CLK>,
-				 <&gcc GCC_QPIC_AHB_CLK>;
-			clock-names = "iface_clk", "bam_clk";
+			clocks = <&gcc GCC_QPIC_AHB_CLK>;
+			clock-names = "bam_clk";
 			#dma-cells = <1>;
 			qcom,ee = <0>;
 			status = "disabled";
@@ -401,7 +399,7 @@
 			reset-names = "phy",
 				      "common";
 
-			pcie_phy0: lane@84200 {
+			pcie_phy0: phy@84200 {
 				reg = <0x0 0x84200 0x0 0x16c>, /* Serdes Tx */
 				      <0x0 0x84400 0x0 0x200>, /* Serdes Rx */
 				      <0x0 0x84800 0x0 0x4f4>; /* PCS: Lane0, COM, PCIE */
@@ -671,6 +669,89 @@
 			};
 		};
 
+		ssphy_0: ssphy@78000 {
+			compatible = "qcom,ipq6018-qmp-usb3-phy";
+			reg = <0x0 0x78000 0x0 0x1C4>;
+			#address-cells = <2>;
+			#size-cells = <2>;
+			#clock-cells = <1>;
+			ranges;
+
+			clocks = <&gcc GCC_USB0_AUX_CLK>,
+				 <&gcc GCC_USB0_PHY_CFG_AHB_CLK>, <&xo>;
+			clock-names = "aux", "cfg_ahb", "ref";
+
+			resets = <&gcc GCC_USB0_PHY_BCR>,
+				 <&gcc GCC_USB3PHY_0_PHY_BCR>;
+			reset-names = "phy","common";
+			status = "disabled";
+
+			usb0_ssphy: lane@78200 {
+				reg = <0x0 0x00078200 0x0 0x130>, /* Tx */
+				      <0x0 0x00078400 0x0 0x200>, /* Rx */
+				      <0x0 0x00078800 0x0 0x1F8>, /* PCS */
+				      <0x0 0x00078600 0x0 0x044>; /* PCS misc */
+				#phy-cells = <0>;
+				clocks = <&gcc GCC_USB0_PIPE_CLK>;
+				clock-names = "pipe0";
+				clock-output-names = "gcc_usb0_pipe_clk_src";
+			};
+		};
+
+		qusb_phy_0: qusb@79000 {
+			compatible = "qcom,ipq6018-qusb2-phy";
+			reg = <0x0 0x079000 0x0 0x180>;
+			#phy-cells = <0>;
+
+			clocks = <&gcc GCC_USB0_PHY_CFG_AHB_CLK>,
+				<&xo>;
+			clock-names = "cfg_ahb", "ref";
+
+			resets = <&gcc GCC_QUSB2_0_PHY_BCR>;
+			status = "disabled";
+		};
+
+		usb3: usb3@8A00000 {
+			compatible = "qcom,ipq6018-dwc3", "qcom,dwc3";
+			reg = <0x0 0x8AF8800 0x0 0x400>;
+			#address-cells = <2>;
+			#size-cells = <2>;
+			ranges;
+
+			clocks = <&gcc GCC_SYS_NOC_USB0_AXI_CLK>,
+				<&gcc GCC_USB0_MASTER_CLK>,
+				<&gcc GCC_USB0_SLEEP_CLK>,
+				<&gcc GCC_USB0_MOCK_UTMI_CLK>;
+			clock-names = "sys_noc_axi",
+				"master",
+				"sleep",
+				"mock_utmi";
+
+			assigned-clocks = <&gcc GCC_SYS_NOC_USB0_AXI_CLK>,
+					  <&gcc GCC_USB0_MASTER_CLK>,
+					  <&gcc GCC_USB0_MOCK_UTMI_CLK>;
+			assigned-clock-rates = <133330000>,
+					       <133330000>,
+					       <20000000>;
+
+			resets = <&gcc GCC_USB0_BCR>;
+			status = "disabled";
+
+			dwc_0: usb@8A00000 {
+				compatible = "snps,dwc3";
+				reg = <0x0 0x8A00000 0x0 0xcd00>;
+				interrupts = <GIC_SPI 140 IRQ_TYPE_LEVEL_HIGH>;
+				phys = <&qusb_phy_0>, <&usb0_ssphy>;
+				phy-names = "usb2-phy", "usb3-phy";
+				tx-fifo-resize;
+				snps,is-utmi-l1-suspend;
+				snps,hird-threshold = /bits/ 8 <0x0>;
+				snps,dis_u2_susphy_quirk;
+				snps,dis_u3_susphy_quirk;
+				snps,ref-clock-period-ns = <0x32>;
+				dr_mode = "host";
+			};
+		};
 	};
 
 	wcss: wcss-smp2p {
diff --git a/arch/arm64/boot/dts/qcom/ipq8074-hk01.dts b/arch/arm64/boot/dts/qcom/ipq8074-hk01.dts
index cc08dc4eb56a..b5e1eaa367bf 100644
--- a/arch/arm64/boot/dts/qcom/ipq8074-hk01.dts
+++ b/arch/arm64/boot/dts/qcom/ipq8074-hk01.dts
@@ -24,6 +24,8 @@
 		device_type = "memory";
 		reg = <0x0 0x40000000 0x0 0x20000000>;
 	};
+
+	vreg_dummy: regulator-dummy { };
 };
 
 &blsp1_i2c2 {
@@ -97,10 +99,14 @@
 
 &ssphy_0 {
 	status = "okay";
+	vdda-phy-supply = <&vreg_dummy>;
+	vdda-pll-supply = <&vreg_dummy>;
 };
 
 &ssphy_1 {
 	status = "okay";
+	vdda-phy-supply = <&vreg_dummy>;
+	vdda-pll-supply = <&vreg_dummy>;
 };
 
 &usb_0 {
diff --git a/arch/arm64/boot/dts/qcom/ipq8074.dtsi b/arch/arm64/boot/dts/qcom/ipq8074.dtsi
index db333001df4d..6c6a0f853669 100644
--- a/arch/arm64/boot/dts/qcom/ipq8074.dtsi
+++ b/arch/arm64/boot/dts/qcom/ipq8074.dtsi
@@ -91,7 +91,6 @@
 		ssphy_1: phy@58000 {
 			compatible = "qcom,ipq8074-qmp-usb3-phy";
 			reg = <0x00058000 0x1c4>;
-			#clock-cells = <1>;
 			#address-cells = <1>;
 			#size-cells = <1>;
 			ranges;
@@ -106,12 +105,13 @@
 			reset-names = "phy","common";
 			status = "disabled";
 
-			usb1_ssphy: lane@58200 {
+			usb1_ssphy: phy@58200 {
 				reg = <0x00058200 0x130>,       /* Tx */
 				      <0x00058400 0x200>,     /* Rx */
 				      <0x00058800 0x1f8>,     /* PCS  */
 				      <0x00058600 0x044>;     /* PCS misc*/
 				#phy-cells = <0>;
+				#clock-cells = <1>;
 				clocks = <&gcc GCC_USB1_PIPE_CLK>;
 				clock-names = "pipe0";
 				clock-output-names = "gcc_usb1_pipe_clk_src";
@@ -134,7 +134,6 @@
 		ssphy_0: phy@78000 {
 			compatible = "qcom,ipq8074-qmp-usb3-phy";
 			reg = <0x00078000 0x1c4>;
-			#clock-cells = <1>;
 			#address-cells = <1>;
 			#size-cells = <1>;
 			ranges;
@@ -149,12 +148,13 @@
 			reset-names = "phy","common";
 			status = "disabled";
 
-			usb0_ssphy: lane@78200 {
+			usb0_ssphy: phy@78200 {
 				reg = <0x00078200 0x130>,       /* Tx */
 				      <0x00078400 0x200>,     /* Rx */
 				      <0x00078800 0x1f8>,     /* PCS  */
 				      <0x00078600 0x044>;     /* PCS misc*/
 				#phy-cells = <0>;
+				#clock-cells = <1>;
 				clocks = <&gcc GCC_USB0_PIPE_CLK>;
 				clock-names = "pipe0";
 				clock-output-names = "gcc_usb0_pipe_clk_src";
@@ -174,34 +174,60 @@
 			status = "disabled";
 		};
 
-		pcie_phy0: phy@86000 {
+		pcie_qmp0: phy@86000 {
 			compatible = "qcom,ipq8074-qmp-pcie-phy";
 			reg = <0x00086000 0x1000>;
-			#phy-cells = <0>;
-			clocks = <&gcc GCC_PCIE0_PIPE_CLK>;
-			clock-names = "pipe_clk";
-			clock-output-names = "pcie20_phy0_pipe_clk";
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges;
 
+			clocks = <&gcc GCC_PCIE0_AUX_CLK>,
+				<&gcc GCC_PCIE0_AHB_CLK>;
+			clock-names = "aux", "cfg_ahb";
 			resets = <&gcc GCC_PCIE0_PHY_BCR>,
 				<&gcc GCC_PCIE0PHY_PHY_BCR>;
 			reset-names = "phy",
 				      "common";
 			status = "disabled";
+
+			pcie_phy0: phy@86200 {
+				reg = <0x86200 0x16c>,
+				      <0x86400 0x200>,
+				      <0x86800 0x4f4>;
+				#phy-cells = <0>;
+				#clock-cells = <0>;
+				clocks = <&gcc GCC_PCIE0_PIPE_CLK>;
+				clock-names = "pipe0";
+				clock-output-names = "pcie_0_pipe_clk";
+			};
 		};
 
-		pcie_phy1: phy@8e000 {
+		pcie_qmp1: phy@8e000 {
 			compatible = "qcom,ipq8074-qmp-pcie-phy";
 			reg = <0x0008e000 0x1000>;
-			#phy-cells = <0>;
-			clocks = <&gcc GCC_PCIE1_PIPE_CLK>;
-			clock-names = "pipe_clk";
-			clock-output-names = "pcie20_phy1_pipe_clk";
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges;
 
+			clocks = <&gcc GCC_PCIE1_AUX_CLK>,
+				<&gcc GCC_PCIE1_AHB_CLK>;
+			clock-names = "aux", "cfg_ahb";
 			resets = <&gcc GCC_PCIE1_PHY_BCR>,
 				<&gcc GCC_PCIE1PHY_PHY_BCR>;
 			reset-names = "phy",
 				      "common";
 			status = "disabled";
+
+			pcie_phy1: phy@8e200 {
+				reg = <0x8e200 0x16c>,
+				      <0x8e400 0x200>,
+				      <0x8e800 0x4f4>;
+				#phy-cells = <0>;
+				#clock-cells = <0>;
+				clocks = <&gcc GCC_PCIE1_PIPE_CLK>;
+				clock-names = "pipe0";
+				clock-output-names = "pcie_1_pipe_clk";
+			};
 		};
 
 		prng: rng@e3000 {
@@ -212,7 +238,7 @@
 			status = "disabled";
 		};
 
-		cryptobam: dma@704000 {
+		cryptobam: dma-controller@704000 {
 			compatible = "qcom,bam-v1.7.0";
 			reg = <0x00704000 0x20000>;
 			interrupts = <GIC_SPI 207 IRQ_TYPE_LEVEL_HIGH>;
@@ -220,7 +246,7 @@
 			clock-names = "bam_clk";
 			#dma-cells = <1>;
 			qcom,ee = <1>;
-			qcom,controlled-remotely = <1>;
+			qcom,controlled-remotely;
 			status = "disabled";
 		};
 
@@ -293,6 +319,25 @@
 			#reset-cells = <0x1>;
 		};
 
+		spmi_bus: spmi@200f000 {
+			compatible = "qcom,spmi-pmic-arb";
+			reg = <0x0200f000 0x001000>,
+			      <0x02400000 0x800000>,
+			      <0x02c00000 0x800000>,
+			      <0x03800000 0x200000>,
+			      <0x0200a000 0x000700>;
+			reg-names = "core", "chnls", "obsrvr", "intr", "cnfg";
+			interrupts = <GIC_SPI 190 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "periph_irq";
+			qcom,ee = <0>;
+			qcom,channel = <0>;
+			#address-cells = <2>;
+			#size-cells = <0>;
+			interrupt-controller;
+			#interrupt-cells = <4>;
+			cell-index = <0>;
+		};
+
 		sdhc_1: sdhci@7824900 {
 			compatible = "qcom,sdhci-msm-v4";
 			reg = <0x7824900 0x500>, <0x7824000 0x800>;
@@ -411,6 +456,21 @@
 			status = "disabled";
 		};
 
+		blsp1_i2c5: i2c@78b9000 {
+			compatible = "qcom,i2c-qup-v2.2.1";
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0x78b9000 0x600>;
+			interrupts = <GIC_SPI 299 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&gcc GCC_BLSP1_AHB_CLK>,
+				 <&gcc GCC_BLSP1_QUP5_I2C_APPS_CLK>;
+			clock-names = "iface", "core";
+			clock-frequency = <400000>;
+			dmas = <&blsp_dma 21>, <&blsp_dma 20>;
+			dma-names = "rx", "tx";
+			status = "disabled";
+		};
+
 		blsp1_i2c6: i2c@78ba000 {
 			compatible = "qcom,i2c-qup-v2.2.1";
 			#address-cells = <1>;
diff --git a/arch/arm64/boot/dts/qcom/msm8916-alcatel-idol347.dts b/arch/arm64/boot/dts/qcom/msm8916-alcatel-idol347.dts
index 670bd1bebd73..265e539e7e99 100644
--- a/arch/arm64/boot/dts/qcom/msm8916-alcatel-idol347.dts
+++ b/arch/arm64/boot/dts/qcom/msm8916-alcatel-idol347.dts
@@ -9,6 +9,7 @@
 / {
 	model = "Alcatel OneTouch Idol 3 (4.7)";
 	compatible = "alcatel,idol347", "qcom,msm8916";
+	chassis-type = "handset";
 
 	aliases {
 		serial0 = &blsp1_uart2;
diff --git a/arch/arm64/boot/dts/qcom/msm8916-asus-z00l.dts b/arch/arm64/boot/dts/qcom/msm8916-asus-z00l.dts
index cee451e59385..d4d33dd3584a 100644
--- a/arch/arm64/boot/dts/qcom/msm8916-asus-z00l.dts
+++ b/arch/arm64/boot/dts/qcom/msm8916-asus-z00l.dts
@@ -4,10 +4,13 @@
 
 #include "msm8916-pm8916.dtsi"
 #include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/interrupt-controller/irq.h>
 
 / {
 	model = "Asus Zenfone 2 Laser";
 	compatible = "asus,z00l", "qcom,msm8916";
+	chassis-type = "handset";
 
 	aliases {
 		serial0 = &blsp1_uart2;
@@ -40,6 +43,21 @@
 		};
 	};
 
+	reg_sd_vmmc: regulator-sdcard-vmmc {
+		compatible = "regulator-fixed";
+		regulator-name = "sdcard-vmmc";
+		regulator-min-microvolt = <2950000>;
+		regulator-max-microvolt = <2950000>;
+
+		gpio = <&msmgpio 87 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+
+		startup-delay-us = <200>;
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&sd_vmmc_en_default>;
+	};
+
 	usb_id: usb-id {
 		compatible = "linux,extcon-usb-gpio";
 		id-gpios = <&msmgpio 110 GPIO_ACTIVE_HIGH>;
@@ -48,6 +66,64 @@
 	};
 };
 
+&blsp_i2c2 {
+	status = "okay";
+
+	magnetometer@c {
+		compatible = "asahi-kasei,ak09911";
+		reg = <0x0c>;
+
+		vdd-supply = <&pm8916_l8>;
+		vid-supply = <&pm8916_l6>;
+
+		reset-gpios = <&msmgpio 112 GPIO_ACTIVE_LOW>;
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&mag_reset_default>;
+	};
+
+	imu@68 {
+		compatible = "invensense,mpu6515";
+		reg = <0x68>;
+
+		interrupt-parent = <&msmgpio>;
+		interrupts = <36 IRQ_TYPE_EDGE_RISING>;
+
+		vdd-supply = <&pm8916_l17>;
+		vddio-supply = <&pm8916_l6>;
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&imu_default>;
+
+		mount-matrix = "1",  "0", "0",
+			       "0", "-1", "0",
+			       "0",  "0", "1";
+	};
+};
+
+&blsp_i2c5 {
+	status = "okay";
+
+	touchscreen@38 {
+		compatible = "edt,edt-ft5306";
+		reg = <0x38>;
+
+		interrupt-parent = <&msmgpio>;
+		interrupts = <13 IRQ_TYPE_EDGE_FALLING>;
+
+		reset-gpios = <&msmgpio 12 GPIO_ACTIVE_LOW>;
+
+		vcc-supply = <&pm8916_l11>;
+		iovcc-supply = <&pm8916_l6>;
+
+		touchscreen-size-x = <720>;
+		touchscreen-size-y = <1280>;
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&touchscreen_default>;
+	};
+};
+
 &blsp1_uart2 {
 	status = "okay";
 };
@@ -64,6 +140,16 @@
 	pinctrl-1 = <&sdc1_clk_off &sdc1_cmd_off &sdc1_data_off>;
 };
 
+&sdhc_2 {
+	status = "okay";
+	vmmc-supply = <&reg_sd_vmmc>;
+
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&sdc2_clk_on &sdc2_cmd_on &sdc2_data_on &sdc2_cd_on>;
+	pinctrl-1 = <&sdc2_clk_off &sdc2_cmd_off &sdc2_data_off &sdc2_cd_off>;
+	cd-gpios = <&msmgpio 38 GPIO_ACTIVE_LOW>;
+};
+
 &usb {
 	status = "okay";
 	extcon = <&usb_id>, <&usb_id>;
@@ -185,6 +271,46 @@
 		bias-pull-up;
 	};
 
+	imu_default: imu-default {
+		pins = "gpio36";
+		function = "gpio";
+
+		drive-strength = <2>;
+		bias-disable;
+	};
+
+	mag_reset_default: mag-reset-default {
+		pins = "gpio112";
+		function = "gpio";
+
+		drive-strength = <2>;
+		bias-disable;
+	};
+
+	sd_vmmc_en_default: sd-vmmc-en-default {
+		pins = "gpio87";
+		function = "gpio";
+
+		drive-strength = <2>;
+		bias-disable;
+	};
+
+	touchscreen_default: touchscreen-default {
+		pins = "gpio13";
+		function = "gpio";
+
+		drive-strength = <2>;
+		bias-pull-up;
+
+		reset {
+			pins = "gpio12";
+			function = "gpio";
+
+			drive-strength = <2>;
+			bias-disable;
+		};
+	};
+
 	usb_id_default: usb-id-default {
 		pins = "gpio110";
 		function = "gpio";
diff --git a/arch/arm64/boot/dts/qcom/msm8916-huawei-g7.dts b/arch/arm64/boot/dts/qcom/msm8916-huawei-g7.dts
index e0075b574190..42d93d3fba36 100644
--- a/arch/arm64/boot/dts/qcom/msm8916-huawei-g7.dts
+++ b/arch/arm64/boot/dts/qcom/msm8916-huawei-g7.dts
@@ -25,6 +25,7 @@
 / {
 	model = "Huawei Ascend G7";
 	compatible = "huawei,g7", "qcom,msm8916";
+	chassis-type = "handset";
 
 	aliases {
 		serial0 = &blsp1_uart2;
diff --git a/arch/arm64/boot/dts/qcom/msm8916-longcheer-l8150.dts b/arch/arm64/boot/dts/qcom/msm8916-longcheer-l8150.dts
index 1e893c0b6fbc..852de624f5af 100644
--- a/arch/arm64/boot/dts/qcom/msm8916-longcheer-l8150.dts
+++ b/arch/arm64/boot/dts/qcom/msm8916-longcheer-l8150.dts
@@ -11,6 +11,7 @@
 / {
 	model = "Longcheer L8150";
 	compatible = "longcheer,l8150", "qcom,msm8916-v1-qrd/9-v1", "qcom,msm8916";
+	chassis-type = "handset";
 
 	aliases {
 		serial0 = &blsp1_uart2;
@@ -30,14 +31,6 @@
 		};
 	};
 
-	// FIXME: Use extcon device provided by charger driver when available
-	usb_vbus: usb-vbus {
-		compatible = "linux,extcon-usb-gpio";
-		vbus-gpio = <&msmgpio 62 GPIO_ACTIVE_HIGH>;
-		pinctrl-names = "default";
-		pinctrl-0 = <&usb_vbus_default>;
-	};
-
 	gpio-keys {
 		compatible = "gpio-keys";
 
@@ -121,9 +114,21 @@
 	status = "okay";
 
 	accelerometer@10 {
-		compatible = "bosch,bmc150_accel";
+		compatible = "bosch,bmc156_accel";
 		reg = <0x10>;
 
+		/*
+		 * For some reason the interrupt line is usually not connected
+		 * to the BMC156. However, there are two pads next to the chip
+		 * that can be shorted to make it work if needed.
+		 *
+		 * interrupt-parent = <&msmgpio>;
+		 * interrupts = <116 IRQ_TYPE_EDGE_RISING>;
+		 */
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&accel_int_default>;
+
 		vdd-supply = <&pm8916_l17>;
 		vddio-supply = <&pm8916_l6>;
 
@@ -133,9 +138,15 @@
 	};
 
 	magnetometer@12 {
-		compatible = "bosch,bmc150_magn";
+		compatible = "bosch,bmc156_magn";
 		reg = <0x12>;
 
+		interrupt-parent = <&msmgpio>;
+		interrupts = <113 IRQ_TYPE_EDGE_RISING>;
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&magn_int_default>;
+
 		vdd-supply = <&pm8916_l17>;
 		vddio-supply = <&pm8916_l6>;
 	};
@@ -145,7 +156,8 @@
 		reg = <0x68>;
 
 		interrupt-parent = <&msmgpio>;
-		interrupts = <23 IRQ_TYPE_EDGE_RISING>;
+		interrupts = <23 IRQ_TYPE_EDGE_RISING>,
+			     <22 IRQ_TYPE_EDGE_RISING>;
 
 		pinctrl-names = "default";
 		pinctrl-0 = <&gyro_int_default>;
@@ -196,6 +208,10 @@
 	linux,code = <KEY_VOLUMEDOWN>;
 };
 
+&pm8916_usbin {
+	status = "okay";
+};
+
 &pm8916_vib {
 	status = "okay";
 };
@@ -225,11 +241,11 @@
 &usb {
 	status = "okay";
 	dr_mode = "peripheral";
-	extcon = <&usb_vbus>;
+	extcon = <&pm8916_usbin>;
 };
 
 &usb_hs_phy {
-	extcon = <&usb_vbus>;
+	extcon = <&pm8916_usbin>;
 };
 
 &smd_rpm_regulators {
@@ -336,6 +352,14 @@
 };
 
 &msmgpio {
+	accel_int_default: accel-int-default {
+		pins = "gpio116";
+		function = "gpio";
+
+		drive-strength = <2>;
+		bias-disable;
+	};
+
 	camera_flash_default: camera-flash-default {
 		pins = "gpio31", "gpio32";
 		function = "gpio";
@@ -361,25 +385,26 @@
 	};
 
 	gyro_int_default: gyro-int-default {
-		pins = "gpio23";
+		pins = "gpio22", "gpio23";
 		function = "gpio";
 
 		drive-strength = <2>;
 		bias-disable;
 	};
 
-	tp_int_default: tp-int-default {
-		pins = "gpio13";
+	magn_int_default: magn-int-default {
+		pins = "gpio113";
 		function = "gpio";
 
 		drive-strength = <2>;
 		bias-disable;
 	};
 
-	usb_vbus_default: usb-vbus-default {
-		pins = "gpio62";
+	tp_int_default: tp-int-default {
+		pins = "gpio13";
 		function = "gpio";
 
-		bias-pull-up;
+		drive-strength = <2>;
+		bias-disable;
 	};
 };
diff --git a/arch/arm64/boot/dts/qcom/msm8916-longcheer-l8910.dts b/arch/arm64/boot/dts/qcom/msm8916-longcheer-l8910.dts
index 27845189ac2b..f9ce123471d4 100644
--- a/arch/arm64/boot/dts/qcom/msm8916-longcheer-l8910.dts
+++ b/arch/arm64/boot/dts/qcom/msm8916-longcheer-l8910.dts
@@ -10,6 +10,7 @@
 / {
 	model = "BQ Aquaris X5 (Longcheer L8910)";
 	compatible = "longcheer,l8910", "qcom,msm8916";
+	chassis-type = "handset";
 
 	aliases {
 		serial0 = &blsp1_uart2;
diff --git a/arch/arm64/boot/dts/qcom/msm8916-mtp.dts b/arch/arm64/boot/dts/qcom/msm8916-mtp.dts
index d66c15538785..7c0ceb3cff45 100644
--- a/arch/arm64/boot/dts/qcom/msm8916-mtp.dts
+++ b/arch/arm64/boot/dts/qcom/msm8916-mtp.dts
@@ -5,9 +5,22 @@
 
 /dts-v1/;
 
-#include "msm8916-mtp.dtsi"
+#include "msm8916-pm8916.dtsi"
 
 / {
 	model = "Qualcomm Technologies, Inc. MSM 8916 MTP";
 	compatible = "qcom,msm8916-mtp", "qcom,msm8916-mtp/1", "qcom,msm8916";
+
+	aliases {
+		serial0 = &blsp1_uart2;
+		usid0 = &pm8916_0;
+	};
+
+	chosen {
+		stdout-path = "serial0";
+	};
+};
+
+&blsp1_uart2 {
+	status = "okay";
 };
diff --git a/arch/arm64/boot/dts/qcom/msm8916-mtp.dtsi b/arch/arm64/boot/dts/qcom/msm8916-mtp.dtsi
deleted file mode 100644
index 1bd05046cdeb..000000000000
--- a/arch/arm64/boot/dts/qcom/msm8916-mtp.dtsi
+++ /dev/null
@@ -1,21 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0-only
-/*
- * Copyright (c) 2014-2015, The Linux Foundation. All rights reserved.
- */
-
-#include "msm8916-pm8916.dtsi"
-
-/ {
-	aliases {
-		serial0 = &blsp1_uart2;
-		usid0 = &pm8916_0;
-	};
-
-	chosen {
-		stdout-path = "serial0";
-	};
-};
-
-&blsp1_uart2 {
-	status = "okay";
-};
diff --git a/arch/arm64/boot/dts/qcom/msm8916-samsung-a3u-eur.dts b/arch/arm64/boot/dts/qcom/msm8916-samsung-a3u-eur.dts
index 6cc2eaeb1d33..4ba11b020f9b 100644
--- a/arch/arm64/boot/dts/qcom/msm8916-samsung-a3u-eur.dts
+++ b/arch/arm64/boot/dts/qcom/msm8916-samsung-a3u-eur.dts
@@ -7,6 +7,7 @@
 / {
 	model = "Samsung Galaxy A3U (EUR)";
 	compatible = "samsung,a3u-eur", "qcom,msm8916";
+	chassis-type = "handset";
 
 	reg_panel_vdd3: regulator-panel-vdd3 {
 		compatible = "regulator-fixed";
diff --git a/arch/arm64/boot/dts/qcom/msm8916-samsung-a5u-eur.dts b/arch/arm64/boot/dts/qcom/msm8916-samsung-a5u-eur.dts
index c2eff5aebf85..d978c9ac179d 100644
--- a/arch/arm64/boot/dts/qcom/msm8916-samsung-a5u-eur.dts
+++ b/arch/arm64/boot/dts/qcom/msm8916-samsung-a5u-eur.dts
@@ -7,6 +7,7 @@
 / {
 	model = "Samsung Galaxy A5U (EUR)";
 	compatible = "samsung,a5u-eur", "qcom,msm8916";
+	chassis-type = "handset";
 
 	reg_touch_key: regulator-touch-key {
 		compatible = "regulator-fixed";
diff --git a/arch/arm64/boot/dts/qcom/msm8916-samsung-serranove.dts b/arch/arm64/boot/dts/qcom/msm8916-samsung-serranove.dts
new file mode 100644
index 000000000000..a78f87a5bf4f
--- /dev/null
+++ b/arch/arm64/boot/dts/qcom/msm8916-samsung-serranove.dts
@@ -0,0 +1,534 @@
+// SPDX-License-Identifier: GPL-2.0-only
+// Copyright (C) 2019 Stephan Gerhold
+
+/dts-v1/;
+
+#include "msm8916-pm8916.dtsi"
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/interrupt-controller/irq.h>
+
+/*
+ * NOTE: The original firmware from Samsung can only boot ARM32 kernels.
+ * Unfortunately, the firmware is signed and cannot be replaced easily.
+ * There seems to be no way to boot ARM64 kernels on this device at the moment,
+ * even though the hardware would support it.
+ *
+ * However, it is possible to use this device tree by compiling an ARM32 kernel
+ * instead. For clarity and build testing this device tree is maintained next
+ * to the other MSM8916 device trees. However, it is actually used through
+ *   arch/arm/boot/dts/qcom-msm8916-samsung-serranove.dts
+ */
+
+/ {
+	model = "Samsung Galaxy S4 Mini Value Edition";
+	compatible = "samsung,serranove", "qcom,msm8916";
+
+	aliases {
+		serial0 = &blsp1_uart2;
+	};
+
+	chosen {
+		stdout-path = "serial0";
+	};
+
+	reserved-memory {
+		/* Additional memory used by Samsung firmware modifications */
+		tz-apps@85500000 {
+			reg = <0x0 0x85500000 0x0 0xb00000>;
+			no-map;
+		};
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&gpio_keys_default>;
+
+		label = "GPIO Buttons";
+
+		volume-up {
+			label = "Volume Up";
+			gpios = <&msmgpio 107 GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_VOLUMEUP>;
+		};
+
+		home {
+			label = "Home";
+			gpios = <&msmgpio 109 GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_HOMEPAGE>;
+		};
+	};
+
+	gpio-hall-sensor {
+		compatible = "gpio-keys";
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&gpio_hall_sensor_default>;
+
+		label = "GPIO Hall Effect Sensor";
+
+		hall-sensor {
+			label = "Hall Effect Sensor";
+			gpios = <&msmgpio 52 GPIO_ACTIVE_LOW>;
+			linux,input-type = <EV_SW>;
+			linux,code = <SW_LID>;
+			linux,can-disable;
+		};
+	};
+
+	reg_vdd_tsp: regulator-vdd-tsp {
+		compatible = "regulator-fixed";
+		regulator-name = "vdd_tsp";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+
+		gpio = <&msmgpio 73 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&tsp_en_default>;
+	};
+
+	reg_touch_key: regulator-touch-key {
+		compatible = "regulator-fixed";
+		regulator-name = "touch_key";
+		regulator-min-microvolt = <2800000>;
+		regulator-max-microvolt = <2800000>;
+
+		gpio = <&msmgpio 86 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&tkey_en_default>;
+	};
+
+	reg_key_led: regulator-key-led {
+		compatible = "regulator-fixed";
+		regulator-name = "key_led";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+
+		gpio = <&msmgpio 60 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&tkey_led_en_default>;
+	};
+
+	i2c-muic {
+		compatible = "i2c-gpio";
+		sda-gpios = <&msmgpio 105 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>;
+		scl-gpios = <&msmgpio 106 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>;
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&muic_i2c_default>;
+
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		muic: extcon@14 {
+			compatible = "siliconmitus,sm5504-muic";
+			reg = <0x14>;
+
+			interrupt-parent = <&msmgpio>;
+			interrupts = <12 IRQ_TYPE_EDGE_FALLING>;
+
+			pinctrl-names = "default";
+			pinctrl-0 = <&muic_irq_default>;
+		};
+	};
+
+	i2c-tkey {
+		compatible = "i2c-gpio";
+		sda-gpios = <&msmgpio 16 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>;
+		scl-gpios = <&msmgpio 17 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>;
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&tkey_i2c_default>;
+
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		touchkey@20 {
+			compatible = "coreriver,tc360-touchkey";
+			reg = <0x20>;
+
+			interrupt-parent = <&msmgpio>;
+			interrupts = <98 IRQ_TYPE_EDGE_FALLING>;
+
+			vcc-supply = <&reg_touch_key>;
+			vdd-supply = <&reg_key_led>;
+			vddio-supply = <&pm8916_l6>;
+
+			linux,keycodes = <KEY_APPSELECT KEY_BACK>;
+
+			pinctrl-names = "default";
+			pinctrl-0 = <&tkey_default>;
+		};
+	};
+
+	i2c-nfc {
+		compatible = "i2c-gpio";
+		sda-gpios = <&msmgpio 0 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>;
+		scl-gpios = <&msmgpio 1 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>;
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&nfc_i2c_default>;
+
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		nfc@2b {
+			compatible = "nxp,pn547", "nxp,nxp-nci-i2c";
+			reg = <0x2b>;
+
+			interrupt-parent = <&msmgpio>;
+			interrupts = <21 IRQ_TYPE_EDGE_RISING>;
+
+			enable-gpios = <&msmgpio 20 GPIO_ACTIVE_HIGH>;
+			firmware-gpios = <&msmgpio 49 GPIO_ACTIVE_HIGH>;
+
+			pinctrl-names = "default";
+			pinctrl-0 = <&nfc_default>;
+		};
+	};
+};
+
+&blsp_i2c2 {
+	status = "okay";
+
+	imu@6b {
+		compatible = "st,lsm6ds3";
+		reg = <0x6b>;
+
+		interrupt-parent = <&msmgpio>;
+		interrupts = <115 IRQ_TYPE_EDGE_RISING>;
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&imu_irq_default>;
+	};
+};
+
+&blsp_i2c4 {
+	status = "okay";
+
+	battery@35 {
+		compatible = "richtek,rt5033-battery";
+		reg = <0x35>;
+
+		interrupt-parent = <&msmgpio>;
+		interrupts = <121 IRQ_TYPE_EDGE_FALLING>;
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&fg_alert_default>;
+	};
+};
+
+&blsp_i2c5 {
+	status = "okay";
+
+	touchscreen@20 {
+		compatible = "zinitix,bt541";
+		reg = <0x20>;
+
+		interrupt-parent = <&msmgpio>;
+		interrupts = <13 IRQ_TYPE_EDGE_FALLING>;
+
+		touchscreen-size-x = <540>;
+		touchscreen-size-y = <960>;
+
+		vdd-supply = <&reg_vdd_tsp>;
+		vddo-supply = <&pm8916_l6>;
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&tsp_irq_default>;
+	};
+};
+
+&blsp1_uart2 {
+	status = "okay";
+};
+
+&pm8916_resin {
+	status = "okay";
+	linux,code = <KEY_VOLUMEDOWN>;
+};
+
+&pm8916_vib {
+	status = "okay";
+};
+
+&pronto {
+	status = "okay";
+
+	iris {
+		compatible = "qcom,wcn3660b";
+	};
+};
+
+&sdhc_1 {
+	status = "okay";
+
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&sdc1_clk_on &sdc1_cmd_on &sdc1_data_on>;
+	pinctrl-1 = <&sdc1_clk_off &sdc1_cmd_off &sdc1_data_off>;
+};
+
+&sdhc_2 {
+	status = "okay";
+
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&sdc2_clk_on &sdc2_cmd_on &sdc2_data_on>;
+	pinctrl-1 = <&sdc2_clk_off &sdc2_cmd_off &sdc2_data_off>;
+
+	non-removable;
+
+	/*
+	 * FIXME: Disable UHS-I modes since tuning fails with:
+	 *
+	 * sdhci_msm 7864900.sdhci: mmc1: No tuning point found
+	 * mmc1: tuning execution failed: -5
+	 * mmc1: error -5 whilst initialising SD card
+	 *
+	 * This is the quirk used on downstream, which suggests this is
+	 * a hardware limitation. However, probing a card using DDR50 works
+	 * (without tuning), so maybe only tuning is broken?
+	 */
+	no-1-8-v;
+};
+
+&usb {
+	status = "okay";
+	extcon = <&muic>, <&muic>;
+};
+
+&usb_hs_phy {
+	extcon = <&muic>;
+};
+
+&smd_rpm_regulators {
+	vdd_l1_l2_l3-supply = <&pm8916_s3>;
+	vdd_l4_l5_l6-supply = <&pm8916_s4>;
+	vdd_l7-supply = <&pm8916_s4>;
+
+	s3 {
+		regulator-min-microvolt = <1200000>;
+		regulator-max-microvolt = <1300000>;
+	};
+
+	s4 {
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <2100000>;
+	};
+
+	l1 {
+		regulator-min-microvolt = <1225000>;
+		regulator-max-microvolt = <1225000>;
+	};
+
+	l2 {
+		regulator-min-microvolt = <1200000>;
+		regulator-max-microvolt = <1200000>;
+	};
+
+	l4 {
+		regulator-min-microvolt = <2050000>;
+		regulator-max-microvolt = <2050000>;
+	};
+
+	l5 {
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+	};
+
+	l6 {
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+	};
+
+	l7 {
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+	};
+
+	l8 {
+		regulator-min-microvolt = <2850000>;
+		regulator-max-microvolt = <2900000>;
+	};
+
+	l9 {
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+	};
+
+	l10 {
+		regulator-min-microvolt = <2700000>;
+		regulator-max-microvolt = <2800000>;
+	};
+
+	l11 {
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <2950000>;
+		regulator-allow-set-load;
+		regulator-system-load = <200000>;
+	};
+
+	l12 {
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <2950000>;
+	};
+
+	l13 {
+		regulator-min-microvolt = <3075000>;
+		regulator-max-microvolt = <3075000>;
+	};
+
+	l14 {
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <3300000>;
+	};
+
+	l15 {
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <3300000>;
+	};
+
+	l16 {
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <3300000>;
+	};
+
+	l17 {
+		regulator-min-microvolt = <2850000>;
+		regulator-max-microvolt = <2850000>;
+	};
+
+	l18 {
+		regulator-min-microvolt = <2700000>;
+		regulator-max-microvolt = <2700000>;
+	};
+};
+
+&msmgpio {
+	fg_alert_default: fg-alert-default {
+		pins = "gpio121";
+		function = "gpio";
+
+		drive-strength = <2>;
+		bias-disable;
+	};
+
+	gpio_keys_default: gpio-keys-default {
+		pins = "gpio107", "gpio109";
+		function = "gpio";
+
+		drive-strength = <2>;
+		bias-pull-up;
+	};
+
+	gpio_hall_sensor_default: gpio-hall-sensor-default {
+		pins = "gpio52";
+		function = "gpio";
+
+		drive-strength = <2>;
+		bias-disable;
+	};
+
+	imu_irq_default: imu-irq-default {
+		pins = "gpio115";
+		function = "gpio";
+
+		drive-strength = <2>;
+		bias-disable;
+	};
+
+	muic_i2c_default: muic-i2c-default {
+		pins = "gpio105", "gpio106";
+		function = "gpio";
+
+		drive-strength = <2>;
+		bias-disable;
+	};
+
+	muic_irq_default: muic-irq-default {
+		pins = "gpio12";
+		function = "gpio";
+
+		drive-strength = <2>;
+		bias-disable;
+	};
+
+	nfc_default: nfc-default {
+		pins = "gpio20", "gpio49";
+		function = "gpio";
+
+		drive-strength = <2>;
+		bias-disable;
+
+		irq {
+			pins = "gpio21";
+			function = "gpio";
+
+			drive-strength = <2>;
+			bias-pull-down;
+		};
+	};
+
+	nfc_i2c_default: nfc-i2c-default {
+		pins = "gpio0", "gpio1";
+		function = "gpio";
+
+		drive-strength = <2>;
+		bias-disable;
+	};
+
+	tkey_default: tkey-default {
+		pins = "gpio98";
+		function = "gpio";
+
+		drive-strength = <2>;
+		bias-disable;
+	};
+
+	tkey_en_default: tkey-en-default {
+		pins = "gpio86";
+		function = "gpio";
+
+		drive-strength = <2>;
+		bias-disable;
+	};
+
+	tkey_i2c_default: tkey-i2c-default {
+		pins = "gpio16", "gpio17";
+		function = "gpio";
+
+		drive-strength = <2>;
+		bias-disable;
+	};
+
+	tkey_led_en_default: tkey-led-en-default {
+		pins = "gpio60";
+		function = "gpio";
+
+		drive-strength = <2>;
+		bias-disable;
+	};
+
+	tsp_en_default: tsp-en-default {
+		pins = "gpio73";
+		function = "gpio";
+
+		drive-strength = <2>;
+		bias-disable;
+	};
+
+	tsp_irq_default: tsp-irq-default {
+		pins = "gpio13";
+		function = "gpio";
+
+		drive-strength = <2>;
+		bias-disable;
+	};
+};
diff --git a/arch/arm64/boot/dts/qcom/msm8916-wingtech-wt88047.dts b/arch/arm64/boot/dts/qcom/msm8916-wingtech-wt88047.dts
index 4e20cc0008f7..69a44c6f57fc 100644
--- a/arch/arm64/boot/dts/qcom/msm8916-wingtech-wt88047.dts
+++ b/arch/arm64/boot/dts/qcom/msm8916-wingtech-wt88047.dts
@@ -11,6 +11,7 @@
 / {
 	model = "Xiaomi Redmi 2 (Wingtech WT88047)";
 	compatible = "wingtech,wt88047", "qcom,msm8916";
+	chassis-type = "handset";
 
 	aliases {
 		serial0 = &blsp1_uart2;
diff --git a/arch/arm64/boot/dts/qcom/msm8916.dtsi b/arch/arm64/boot/dts/qcom/msm8916.dtsi
index 3f85e34a8ce6..c1c42f26b61e 100644
--- a/arch/arm64/boot/dts/qcom/msm8916.dtsi
+++ b/arch/arm64/boot/dts/qcom/msm8916.dtsi
@@ -41,9 +41,13 @@
 			no-map;
 		};
 
-		smem_mem: smem_region@86300000 {
+		smem@86300000 {
+			compatible = "qcom,smem";
 			reg = <0x0 0x86300000 0x0 0x100000>;
 			no-map;
+
+			hwlocks = <&tcsr_mutex 3>;
+			qcom,rpm-msg-ram = <&rpm_msg_ram>;
 		};
 
 		hypervisor@86400000 {
@@ -124,6 +128,8 @@
 			#cooling-cells = <2>;
 			power-domains = <&CPU_PD0>;
 			power-domain-names = "psci";
+			qcom,acc = <&cpu0_acc>;
+			qcom,saw = <&cpu0_saw>;
 		};
 
 		CPU1: cpu@1 {
@@ -137,6 +143,8 @@
 			#cooling-cells = <2>;
 			power-domains = <&CPU_PD1>;
 			power-domain-names = "psci";
+			qcom,acc = <&cpu1_acc>;
+			qcom,saw = <&cpu1_saw>;
 		};
 
 		CPU2: cpu@2 {
@@ -150,6 +158,8 @@
 			#cooling-cells = <2>;
 			power-domains = <&CPU_PD2>;
 			power-domain-names = "psci";
+			qcom,acc = <&cpu2_acc>;
+			qcom,saw = <&cpu2_saw>;
 		};
 
 		CPU3: cpu@3 {
@@ -163,6 +173,8 @@
 			#cooling-cells = <2>;
 			power-domains = <&CPU_PD3>;
 			power-domain-names = "psci";
+			qcom,acc = <&cpu3_acc>;
+			qcom,saw = <&cpu3_saw>;
 		};
 
 		L2_0: l2-cache {
@@ -323,15 +335,6 @@
 		};
 	};
 
-	smem {
-		compatible = "qcom,smem";
-
-		memory-region = <&smem_mem>;
-		qcom,rpm-msg-ram = <&rpm_msg_ram>;
-
-		hwlocks = <&tcsr_mutex 3>;
-	};
-
 	smp2p-hexagon {
 		compatible = "qcom,smp2p";
 		qcom,smem = <435>, <428>;
@@ -414,7 +417,7 @@
 		};
 	};
 
-	soc: soc {
+	soc: soc@0 {
 		#address-cells = <1>;
 		#size-cells = <1>;
 		ranges = <0 0 0 0xffffffff>;
@@ -445,7 +448,7 @@
 			};
 		};
 
-		rpm_msg_ram: memory@60000 {
+		rpm_msg_ram: sram@60000 {
 			compatible = "qcom,rpm-msg-ram";
 			reg = <0x00060000 0x8000>;
 		};
@@ -1384,11 +1387,17 @@
 		lpass: audio-controller@7708000 {
 			status = "disabled";
 			compatible = "qcom,lpass-cpu-apq8016";
+
+			/*
+			 * Note: Unlike the name would suggest, the SEC_I2S_CLK
+			 * is actually only used by Tertiary MI2S while
+			 * Primary/Secondary MI2S both use the PRI_I2S_CLK.
+			 */
 			clocks = <&gcc GCC_ULTAUDIO_AHBFABRIC_IXFABRIC_CLK>,
 				 <&gcc GCC_ULTAUDIO_PCNOC_MPORT_CLK>,
 				 <&gcc GCC_ULTAUDIO_PCNOC_SWAY_CLK>,
 				 <&gcc GCC_ULTAUDIO_LPAIF_PRI_I2S_CLK>,
-				 <&gcc GCC_ULTAUDIO_LPAIF_SEC_I2S_CLK>,
+				 <&gcc GCC_ULTAUDIO_LPAIF_PRI_I2S_CLK>,
 				 <&gcc GCC_ULTAUDIO_LPAIF_SEC_I2S_CLK>,
 				 <&gcc GCC_ULTAUDIO_LPAIF_AUX_I2S_CLK>;
 
@@ -1420,7 +1429,7 @@
 		};
 
 		sdhc_1: sdhci@7824000 {
-			compatible = "qcom,sdhci-msm-v4";
+			compatible = "qcom,msm8916-sdhci", "qcom,sdhci-msm-v4";
 			reg = <0x07824900 0x11c>, <0x07824000 0x800>;
 			reg-names = "hc_mem", "core_mem";
 
@@ -1438,7 +1447,7 @@
 		};
 
 		sdhc_2: sdhci@7864000 {
-			compatible = "qcom,sdhci-msm-v4";
+			compatible = "qcom,msm8916-sdhci", "qcom,sdhci-msm-v4";
 			reg = <0x07864900 0x11c>, <0x07864000 0x800>;
 			reg-names = "hc_mem", "core_mem";
 
@@ -1765,7 +1774,7 @@
 
 				label = "pronto";
 
-				wcnss {
+				wcnss_ctrl: wcnss {
 					compatible = "qcom,wcnss";
 					qcom,smd-channels = "WCNSS_CTRL";
 
@@ -1871,6 +1880,54 @@
 				status = "disabled";
 			};
 		};
+
+		cpu0_acc: power-manager@b088000 {
+			compatible = "qcom,msm8916-acc";
+			reg = <0x0b088000 0x1000>;
+			status = "reserved"; /* Controlled by PSCI firmware */
+		};
+
+		cpu0_saw: power-manager@b089000 {
+			compatible = "qcom,msm8916-saw2-v3.0-cpu", "qcom,saw2";
+			reg = <0x0b089000 0x1000>;
+			status = "reserved"; /* Controlled by PSCI firmware */
+		};
+
+		cpu1_acc: power-manager@b098000 {
+			compatible = "qcom,msm8916-acc";
+			reg = <0x0b098000 0x1000>;
+			status = "reserved"; /* Controlled by PSCI firmware */
+		};
+
+		cpu1_saw: power-manager@b099000 {
+			compatible = "qcom,msm8916-saw2-v3.0-cpu", "qcom,saw2";
+			reg = <0x0b099000 0x1000>;
+			status = "reserved"; /* Controlled by PSCI firmware */
+		};
+
+		cpu2_acc: power-manager@b0a8000 {
+			compatible = "qcom,msm8916-acc";
+			reg = <0x0b0a8000 0x1000>;
+			status = "reserved"; /* Controlled by PSCI firmware */
+		};
+
+		cpu2_saw: power-manager@b0a9000 {
+			compatible = "qcom,msm8916-saw2-v3.0-cpu", "qcom,saw2";
+			reg = <0x0b0a9000 0x1000>;
+			status = "reserved"; /* Controlled by PSCI firmware */
+		};
+
+		cpu3_acc: power-manager@b0b8000 {
+			compatible = "qcom,msm8916-acc";
+			reg = <0x0b0b8000 0x1000>;
+			status = "reserved"; /* Controlled by PSCI firmware */
+		};
+
+		cpu3_saw: power-manager@b0b9000 {
+			compatible = "qcom,msm8916-saw2-v3.0-cpu", "qcom,saw2";
+			reg = <0x0b0b9000 0x1000>;
+			status = "reserved"; /* Controlled by PSCI firmware */
+		};
 	};
 
 	thermal-zones {
diff --git a/arch/arm64/boot/dts/qcom/msm8992-bullhead-rev-101.dts b/arch/arm64/boot/dts/qcom/msm8992-bullhead-rev-101.dts
index 1ccca83292ac..4da6c44bf532 100644
--- a/arch/arm64/boot/dts/qcom/msm8992-bullhead-rev-101.dts
+++ b/arch/arm64/boot/dts/qcom/msm8992-bullhead-rev-101.dts
@@ -16,6 +16,8 @@
 / {
 	model = "LG Nexus 5X";
 	compatible = "lg,bullhead", "qcom,msm8992";
+	chassis-type = "handset";
+
 	/* required for bootloader to select correct board */
 	qcom,msm-id = <251 0>, <252 0>;
 	qcom,board-id = <0xb64 0>;
diff --git a/arch/arm64/boot/dts/qcom/msm8992-msft-lumia-octagon-talkman.dts b/arch/arm64/boot/dts/qcom/msm8992-msft-lumia-octagon-talkman.dts
index 5322b9ce5839..8933b53694e8 100644
--- a/arch/arm64/boot/dts/qcom/msm8992-msft-lumia-octagon-talkman.dts
+++ b/arch/arm64/boot/dts/qcom/msm8992-msft-lumia-octagon-talkman.dts
@@ -12,4 +12,5 @@
 / {
 	model = "Microsoft Lumia 950";
 	compatible = "microsoft,talkman", "qcom,msm8992";
+	chassis-type = "handset";
 };
diff --git a/arch/arm64/boot/dts/qcom/msm8992-xiaomi-libra.dts b/arch/arm64/boot/dts/qcom/msm8992-xiaomi-libra.dts
index 357d55496e75..69fcb6b0398d 100644
--- a/arch/arm64/boot/dts/qcom/msm8992-xiaomi-libra.dts
+++ b/arch/arm64/boot/dts/qcom/msm8992-xiaomi-libra.dts
@@ -14,6 +14,8 @@
 / {
 	model = "Xiaomi Mi 4C";
 	compatible = "xiaomi,libra", "qcom,msm8992";
+	chassis-type = "handset";
+
 	/* required for bootloader to select correct board */
 	qcom,msm-id = <251 0 252 0>;
 	qcom,pmic-id = <65545 65546 0 0>;
diff --git a/arch/arm64/boot/dts/qcom/msm8994-angler-rev-101.dts b/arch/arm64/boot/dts/qcom/msm8994-angler-rev-101.dts
index c096b7758aa0..0e3dd48f0dbf 100644
--- a/arch/arm64/boot/dts/qcom/msm8994-angler-rev-101.dts
+++ b/arch/arm64/boot/dts/qcom/msm8994-angler-rev-101.dts
@@ -14,6 +14,7 @@
 / {
 	model = "Huawei Nexus 6P";
 	compatible = "huawei,angler", "qcom,msm8994";
+	chassis-type = "handset";
 	/* required for bootloader to select correct board */
 	qcom,msm-id = <207 0x20000>;
 	qcom,pmic-id = <0x10009 0x1000A 0x0 0x0>;
diff --git a/arch/arm64/boot/dts/qcom/msm8994-msft-lumia-octagon-cityman.dts b/arch/arm64/boot/dts/qcom/msm8994-msft-lumia-octagon-cityman.dts
index d0aaf5750c21..c593418202b8 100644
--- a/arch/arm64/boot/dts/qcom/msm8994-msft-lumia-octagon-cityman.dts
+++ b/arch/arm64/boot/dts/qcom/msm8994-msft-lumia-octagon-cityman.dts
@@ -12,4 +12,5 @@
 / {
 	model = "Microsoft Lumia 950 XL";
 	compatible = "microsoft,cityman", "qcom,msm8994";
+	chassis-type = "handset";
 };
diff --git a/arch/arm64/boot/dts/qcom/msm8994-sony-xperia-kitakami-ivy.dts b/arch/arm64/boot/dts/qcom/msm8994-sony-xperia-kitakami-ivy.dts
index b5e90c85aaf6..99388b019a11 100644
--- a/arch/arm64/boot/dts/qcom/msm8994-sony-xperia-kitakami-ivy.dts
+++ b/arch/arm64/boot/dts/qcom/msm8994-sony-xperia-kitakami-ivy.dts
@@ -10,6 +10,7 @@
 / {
 	model = "Sony Xperia Z3+/Z4";
 	compatible = "sony,ivy-row", "qcom,msm8994";
+	chassis-type = "handset";
 };
 
 &pm8994_l3 {
diff --git a/arch/arm64/boot/dts/qcom/msm8994-sony-xperia-kitakami-karin.dts b/arch/arm64/boot/dts/qcom/msm8994-sony-xperia-kitakami-karin.dts
index a1d1a075941a..71758d2cfd5e 100644
--- a/arch/arm64/boot/dts/qcom/msm8994-sony-xperia-kitakami-karin.dts
+++ b/arch/arm64/boot/dts/qcom/msm8994-sony-xperia-kitakami-karin.dts
@@ -10,6 +10,7 @@
 / {
 	model = "Sony Xperia Z4 Tablet (LTE)";
 	compatible = "sony,karin-row", "qcom,msm8994";
+	chassis-type = "tablet";
 };
 
 &blsp2_i2c5 {
diff --git a/arch/arm64/boot/dts/qcom/msm8994-sony-xperia-kitakami-satsuki.dts b/arch/arm64/boot/dts/qcom/msm8994-sony-xperia-kitakami-satsuki.dts
index 1385956a69f3..69b7df0ed605 100644
--- a/arch/arm64/boot/dts/qcom/msm8994-sony-xperia-kitakami-satsuki.dts
+++ b/arch/arm64/boot/dts/qcom/msm8994-sony-xperia-kitakami-satsuki.dts
@@ -10,6 +10,7 @@
 / {
 	model = "Sony Xperia Z5 Premium";
 	compatible = "sony,satsuki-row", "qcom,msm8994";
+	chassis-type = "handset";
 };
 
 &pm8994_l14 {
diff --git a/arch/arm64/boot/dts/qcom/msm8994-sony-xperia-kitakami-sumire.dts b/arch/arm64/boot/dts/qcom/msm8994-sony-xperia-kitakami-sumire.dts
index d3ba9867a369..466508cd8234 100644
--- a/arch/arm64/boot/dts/qcom/msm8994-sony-xperia-kitakami-sumire.dts
+++ b/arch/arm64/boot/dts/qcom/msm8994-sony-xperia-kitakami-sumire.dts
@@ -10,6 +10,7 @@
 / {
 	model = "Sony Xperia Z5";
 	compatible = "sony,sumire-row", "qcom,msm8994";
+	chassis-type = "handset";
 };
 
 /delete-node/ &pm8994_l19;
diff --git a/arch/arm64/boot/dts/qcom/msm8994-sony-xperia-kitakami-suzuran.dts b/arch/arm64/boot/dts/qcom/msm8994-sony-xperia-kitakami-suzuran.dts
index f129479bbf95..76bf50191f9a 100644
--- a/arch/arm64/boot/dts/qcom/msm8994-sony-xperia-kitakami-suzuran.dts
+++ b/arch/arm64/boot/dts/qcom/msm8994-sony-xperia-kitakami-suzuran.dts
@@ -10,6 +10,7 @@
 / {
 	model = "Sony Xperia Z5 Compact";
 	compatible = "sony,suzuran-row", "qcom,msm8994";
+	chassis-type = "handset";
 };
 
 &pm8994_l14 {
diff --git a/arch/arm64/boot/dts/qcom/msm8994.dtsi b/arch/arm64/boot/dts/qcom/msm8994.dtsi
index 986fe60dec5f..5a9a5ed0565f 100644
--- a/arch/arm64/boot/dts/qcom/msm8994.dtsi
+++ b/arch/arm64/boot/dts/qcom/msm8994.dtsi
@@ -715,7 +715,7 @@
 			reg = <0xfc400000 0x2000>;
 		};
 
-		rpm_msg_ram: memory@fc428000 {
+		rpm_msg_ram: sram@fc428000 {
 			compatible = "qcom,rpm-msg-ram";
 			reg = <0xfc428000 0x4000>;
 		};
diff --git a/arch/arm64/boot/dts/qcom/msm8996-mtp.dts b/arch/arm64/boot/dts/qcom/msm8996-mtp.dts
index 45ed594c1b9c..7d9fc35bc7a0 100644
--- a/arch/arm64/boot/dts/qcom/msm8996-mtp.dts
+++ b/arch/arm64/boot/dts/qcom/msm8996-mtp.dts
@@ -5,9 +5,31 @@
 
 /dts-v1/;
 
-#include "msm8996-mtp.dtsi"
+#include "msm8996.dtsi"
 
 / {
 	model = "Qualcomm Technologies, Inc. MSM 8996 MTP";
 	compatible = "qcom,msm8996-mtp";
+
+	aliases {
+		serial0 = &blsp2_uart2;
+	};
+
+	chosen {
+		stdout-path = "serial0";
+	};
+
+	soc {
+		serial@75b0000 {
+			status = "okay";
+		};
+	};
+};
+
+&hdmi {
+	status = "okay";
+};
+
+&hdmi_phy {
+	status = "okay";
 };
diff --git a/arch/arm64/boot/dts/qcom/msm8996-mtp.dtsi b/arch/arm64/boot/dts/qcom/msm8996-mtp.dtsi
deleted file mode 100644
index ac43a91f1104..000000000000
--- a/arch/arm64/boot/dts/qcom/msm8996-mtp.dtsi
+++ /dev/null
@@ -1,30 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0-only
-/*
- * Copyright (c) 2014-2015, The Linux Foundation. All rights reserved.
- */
-
-#include "msm8996.dtsi"
-
-/ {
-	aliases {
-		serial0 = &blsp2_uart2;
-	};
-
-	chosen {
-		stdout-path = "serial0";
-	};
-
-	soc {
-		serial@75b0000 {
-			status = "okay";
-		};
-	};
-};
-
-&hdmi {
-	status = "okay";
-};
-
-&hdmi_phy {
-	status = "okay";
-};
diff --git a/arch/arm64/boot/dts/qcom/msm8996-sony-xperia-tone-dora.dts b/arch/arm64/boot/dts/qcom/msm8996-sony-xperia-tone-dora.dts
index b4cca54dcb68..4a0645db0ae1 100644
--- a/arch/arm64/boot/dts/qcom/msm8996-sony-xperia-tone-dora.dts
+++ b/arch/arm64/boot/dts/qcom/msm8996-sony-xperia-tone-dora.dts
@@ -12,6 +12,7 @@
 / {
 	model = "Sony Xperia X Performance";
 	compatible = "sony,dora-row", "qcom,msm8996";
+	chassis-type = "handset";
 };
 
 /delete-node/ &tof_sensor;
diff --git a/arch/arm64/boot/dts/qcom/msm8996-sony-xperia-tone-kagura.dts b/arch/arm64/boot/dts/qcom/msm8996-sony-xperia-tone-kagura.dts
index be6ea855fcce..d3100ddf926f 100644
--- a/arch/arm64/boot/dts/qcom/msm8996-sony-xperia-tone-kagura.dts
+++ b/arch/arm64/boot/dts/qcom/msm8996-sony-xperia-tone-kagura.dts
@@ -12,4 +12,5 @@
 / {
 	model = "Sony Xperia XZ";
 	compatible = "sony,kagura-row", "qcom,msm8996";
+	chassis-type = "handset";
 };
diff --git a/arch/arm64/boot/dts/qcom/msm8996-sony-xperia-tone-keyaki.dts b/arch/arm64/boot/dts/qcom/msm8996-sony-xperia-tone-keyaki.dts
index 1eee7d0fc178..3e5bdaba8378 100644
--- a/arch/arm64/boot/dts/qcom/msm8996-sony-xperia-tone-keyaki.dts
+++ b/arch/arm64/boot/dts/qcom/msm8996-sony-xperia-tone-keyaki.dts
@@ -12,6 +12,7 @@
 / {
 	model = "Sony Xperia XZs";
 	compatible = "sony,keyaki-row", "qcom,msm8996";
+	chassis-type = "handset";
 };
 
 &pm8994_l19 {
diff --git a/arch/arm64/boot/dts/qcom/msm8996-sony-xperia-tone.dtsi b/arch/arm64/boot/dts/qcom/msm8996-sony-xperia-tone.dtsi
index 507396c4d23b..ff7f39d29dd5 100644
--- a/arch/arm64/boot/dts/qcom/msm8996-sony-xperia-tone.dtsi
+++ b/arch/arm64/boot/dts/qcom/msm8996-sony-xperia-tone.dtsi
@@ -620,6 +620,7 @@
 &pmi8994_wled {
 	status = "okay";
 	default-brightness = <512>;
+	qcom,num-strings = <3>;
 };
 
 &rpm_requests {
diff --git a/arch/arm64/boot/dts/qcom/msm8996-xiaomi-common.dtsi b/arch/arm64/boot/dts/qcom/msm8996-xiaomi-common.dtsi
new file mode 100644
index 000000000000..01e573f0dfbf
--- /dev/null
+++ b/arch/arm64/boot/dts/qcom/msm8996-xiaomi-common.dtsi
@@ -0,0 +1,673 @@
+// SPDX-License-Identifier: BSD-3-Clause
+/*
+ * Copyright (c) 2020, Yassine Oudjana <y.oudjana@protonmail.com>
+ */
+
+/dts-v1/;
+
+#include "msm8996.dtsi"
+#include "pm8994.dtsi"
+#include "pmi8994.dtsi"
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/leds/common.h>
+#include <dt-bindings/pinctrl/qcom,pmic-gpio.h>
+
+/ {
+	clocks {
+		compatible = "simple-bus";
+
+		divclk1_cdc: divclk1 {
+			compatible = "gpio-gate-clock";
+			clocks = <&rpmcc RPM_SMD_DIV_CLK1>;
+			#clock-cells = <0>;
+			enable-gpios = <&pm8994_gpios 15 GPIO_ACTIVE_HIGH>;
+
+			pinctrl-names = "default";
+			pinctrl-0 = <&divclk1_default>;
+		};
+
+		divclk4: divclk4 {
+			compatible = "fixed-clock";
+			#clock-cells = <0>;
+			clock-frequency = <32768>;
+			clock-output-names = "divclk4";
+
+			pinctrl-names = "default";
+			pinctrl-0 = <&divclk4_pin_a>;
+		};
+	};
+
+	gpio_keys {
+		compatible = "gpio-keys";
+
+		vol_up {
+			label = "Volume Up";
+			gpios = <&pm8994_gpios 2 GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_VOLUMEUP>;
+			wakeup-source;
+			debounce-interval = <15>;
+		};
+
+		dome {
+			label = "Home";
+			gpios = <&tlmm 34 GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_HOME>;
+			wakeup-source;
+			debounce-interval = <15>;
+		};
+	};
+
+	reserved-memory {
+		memory@88800000 {
+			reg = <0x0 0x88800000 0x0 0x1400000>;
+			no-map;
+		};
+
+		/* This platform has all PIL regions offset by 0x1400000 */
+		/delete-node/ mpss@88800000;
+		mpss_region: mpss@89c00000 {
+			reg = <0x0 0x89c00000 0x0 0x6200000>;
+			no-map;
+		};
+
+		/delete-node/ adsp@8ea00000;
+		adsp_region: adsp@8ea00000 {
+			reg = <0x0 0x8fe00000 0x0 0x1b00000>;
+			no-map;
+		};
+
+		/delete-node/ slpi@90b00000;
+		slpi_region: slpi@91900000 {
+			reg = <0x0 0x91900000 0x0 0xa00000>;
+			no-map;
+		};
+
+		/delete-node/ gpu@8f200000;
+		zap_shader_region: gpu@92300000 {
+			compatible = "shared-dma-pool";
+			reg = <0x0 0x92300000 0x0 0x2000>;
+			no-map;
+		};
+
+		/delete-node/ venus@91000000;
+		venus_region: venus@90400000 {
+			reg = <0x0 0x92400000 0x0 0x500000>;
+			no-map;
+		};
+
+		ramoops@92900000 {
+			compatible = "ramoops";
+			reg = <0x0 0x92900000 0x0 0x100000>;
+			no-map;
+
+			record-size = <0x8000>;
+			console-size = <0x80000>;
+			ftrace-size = <0x20000>;
+			pmsg-size = <0x40000>;
+		};
+
+		/delete-node/ rmtfs@86700000;
+		rmtfs@f6c00000 {
+			compatible = "qcom,rmtfs-mem";
+			reg = <0 0xf6c00000 0 0x200000>;
+			no-map;
+
+			qcom,client-id = <1>;
+			qcom,vmid = <15>;
+		};
+
+		/delete-node/ mba@91500000;
+		mba_region: mba@f6f00000 {
+			reg = <0x0 0xf6f00000 0x0 0x100000>;
+			no-map;
+		};
+	};
+
+	vph_pwr: vph-pwr-regulator {
+		compatible = "regulator-fixed";
+		regulator-name = "vph_pwr";
+		regulator-min-microvolt = <3800000>;
+		regulator-max-microvolt = <3800000>;
+		regulator-always-on;
+		regulator-boot-on;
+	};
+
+	vdd_3v2_tp: vdd-3v2-tp {
+		compatible = "regulator-fixed";
+		regulator-name = "vdd_3v2_tp";
+		regulator-min-microvolt = <3200000>;
+		regulator-max-microvolt = <3200000>;
+		startup-delay-us = <4000>;
+		vin-supply = <&vph_pwr>;
+
+		gpio = <&tlmm 73 0>;
+		enable-active-high;
+	};
+
+	vdd_3v3: rome-vreg {
+		compatible = "regulator-fixed";
+		regulator-name = "vdd_3v3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		startup-delay-us = <4000>;
+		vin-supply = <&vph_pwr_bbyp>;
+
+		gpio = <&pm8994_gpios 9 0>;
+		enable-active-high;
+		pinctrl-names = "default";
+		pinctrl-0 = <&rome_enable_default>;
+
+		/* Required by QCA6174a - vddpe-3v3 */
+		regulator-always-on;
+	};
+
+	/* WL_EN pin defined as a fixed regulator */
+	wlan_en: wlan-en-1-8v {
+		compatible = "regulator-fixed";
+		regulator-name = "wlan-en-regulator";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+
+		gpio = <&pm8994_gpios 8 0>;
+		/* WLAN card specific delay */
+		startup-delay-us = <70000>;
+		enable-active-high;
+		pinctrl-names = "default";
+		pinctrl-0 = <&wlan_en_default>;
+	};
+};
+
+&adsp_pil {
+	status = "okay";
+};
+
+&blsp2_i2c2 {
+	status = "okay";
+	label = "NFC_I2C";
+	clock-frequency = <400000>;
+
+	nfc: pn548@28 {
+		compatible = "nxp,nxp-nci-i2c";
+
+		reg = <0x28>;
+
+		interrupt-parent = <&tlmm>;
+		interrupts = <9 IRQ_TYPE_LEVEL_HIGH>;
+
+		enable-gpios = <&tlmm 12 GPIO_ACTIVE_HIGH>;
+		firmware-gpios = <&tlmm 21 GPIO_ACTIVE_HIGH>;
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&nfc_default>;
+	};
+};
+
+&blsp2_i2c3 {
+	status = "okay";
+	label = "TYPEC_I2C";
+
+	typec: tusb320@47 {
+		compatible = "ti,tusb320";
+		reg = <0x47>;
+		interrupt-parent = <&tlmm>;
+		interrupts = <63 IRQ_TYPE_EDGE_RISING>;
+	};
+};
+
+&blsp2_i2c6 {
+	status = "okay";
+	label = "MSM_TS_I2C";
+};
+
+&blsp1_uart2 {
+	status = "okay";
+	label = "QCA_UART";
+
+	bluetooth: qca6174a {
+		compatible = "qcom,qca6174-bt";
+
+		enable-gpios = <&pm8994_gpios 19 GPIO_ACTIVE_HIGH>;
+		clocks = <&divclk4>;
+	};
+};
+
+&dsi0 {
+	status = "okay";
+
+	vdd-supply = <&vreg_l2a_1p25>;
+	vddio-supply = <&vreg_l14a_1p8>;
+
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&mdss_dsi_default &mdss_te_default>;
+	pinctrl-1 = <&mdss_dsi_sleep &mdss_te_sleep>;
+};
+
+&dsi0_out {
+	status = "okay";
+
+	data-lanes = <0 1 2 3>;
+};
+
+&dsi0_phy {
+	status = "okay";
+
+	vcca-supply = <&vreg_l28a_0p925>;
+};
+
+&gpu {
+	status = "okay";
+};
+
+&mdss {
+	status = "okay";
+};
+
+&mmcc {
+	vdd-gfx-supply = <&vdd_gfx>;
+};
+
+&pcie0 {
+	status = "okay";
+
+	/* Supplied by vdd_3v3, but choose wlan_en to drive enable pin high */
+	vddpe-3v3-supply = <&wlan_en>;
+	vdda-supply = <&vreg_l28a_0p925>;
+
+	perst-gpios = <&tlmm 35 GPIO_ACTIVE_LOW>;
+	wake-gpios = <&tlmm 37 GPIO_ACTIVE_HIGH>;
+};
+
+&pcie_phy {
+	status = "okay";
+
+	vdda-phy-supply = <&vreg_l28a_0p925>;
+	vdda-pll-supply = <&vreg_l12a_1p8>;
+};
+
+&pm8994_resin {
+	status = "okay";
+
+	linux,code = <KEY_VOLUMEDOWN>;
+};
+
+&usb3 {
+	status = "okay";
+	extcon = <&typec>;
+
+	qcom,select-utmi-as-pipe-clk;
+
+	dwc3@6a00000 {
+		extcon = <&typec>;
+
+		/* usb3-phy is not used on this device */
+		phys = <&hsusb_phy1>;
+		phy-names = "usb2-phy";
+
+		maximum-speed = "high-speed";
+		snps,is-utmi-l1-suspend;
+		snps,usb2-gadget-lpm-disable;
+		snps,hird-threshold = /bits/ 8 <0>;
+	};
+};
+
+&hsusb_phy1 {
+	status = "okay";
+	extcon = <&typec>;
+
+	vdda-pll-supply = <&vreg_l12a_1p8>;
+	vdda-phy-dpdm-supply = <&vreg_l24a_3p075>;
+};
+
+&ufshc {
+	status = "okay";
+
+	vcc-supply = <&vreg_l20a_2p95>;
+	vccq-supply = <&vreg_l25a_1p2>;
+	vccq2-supply = <&vreg_s4a_1p8>;
+
+	vcc-max-microamp = <600000>;
+	vccq-max-microamp = <450000>;
+	vccq2-max-microamp = <450000>;
+};
+
+&ufsphy {
+	status = "okay";
+
+	vdda-phy-supply = <&vreg_l28a_0p925>;
+	vdda-pll-supply = <&vreg_l12a_1p8>;
+
+	vdda-phy-max-microamp = <18380>;
+	vdda-pll-max-microamp = <9440>;
+
+	vddp-ref-clk-supply = <&vreg_l25a_1p2>;
+	vddp-ref-clk-max-microamp = <100>;
+	vddp-ref-clk-always-on;
+};
+
+&venus {
+	status = "okay";
+};
+
+&wcd9335 {
+	clock-names = "mclk", "slimbus";
+	clocks = <&divclk1_cdc>,
+		 <&rpmcc RPM_SMD_BB_CLK1>;
+
+	vdd-buck-supply = <&vreg_s4a_1p8>;
+	vdd-buck-sido-supply = <&vreg_s4a_1p8>;
+	vdd-rx-supply = <&vreg_s4a_1p8>;
+	vdd-tx-supply = <&vreg_s4a_1p8>;
+	vdd-vbat-supply = <&vph_pwr>;
+	vdd-micbias-supply = <&vph_pwr_bbyp>;
+	vdd-io-supply = <&vreg_s4a_1p8>;
+};
+
+&rpm_requests {
+	pm8994-regulators {
+		compatible = "qcom,rpm-pm8994-regulators";
+
+		vdd_s1-supply = <&vph_pwr>;
+		vdd_s2-supply = <&vph_pwr>;
+		vdd_s3-supply = <&vph_pwr>;
+		vdd_s4-supply = <&vph_pwr>;
+		vdd_s5-supply = <&vph_pwr>;
+		vdd_s6-supply = <&vph_pwr>;
+		vdd_s7-supply = <&vph_pwr>;
+		vdd_s8-supply = <&vph_pwr>;
+		vdd_s9-supply = <&vph_pwr>;
+		vdd_s10-supply = <&vph_pwr>;
+		vdd_s11-supply = <&vph_pwr>;
+		vdd_s12-supply = <&vph_pwr>;
+		vdd_l1-supply = <&vreg_s1b_1p025>;
+		vdd_l2_l26_l28-supply = <&vreg_s3a_1p3>;
+		vdd_l3_l11-supply = <&vreg_s3a_1p3>;
+		vdd_l4_l27_l31-supply = <&vreg_s3a_1p3>;
+		vdd_l5_l7-supply = <&vreg_s5a_2p15>;
+		vdd_l6_l12_l32-supply = <&vreg_s5a_2p15>;
+		vdd_l8_l16_l30-supply = <&vph_pwr>;
+		vdd_l9_l10_l18_l22-supply = <&vph_pwr_bbyp>;
+		vdd_l13_l19_l23_l24-supply = <&vph_pwr_bbyp>;
+		vdd_l14_l15-supply = <&vreg_s5a_2p15>;
+		vdd_l17_l29-supply = <&vph_pwr_bbyp>;
+		vdd_l20_l21-supply = <&vph_pwr_bbyp>;
+		vdd_l25-supply = <&vreg_s3a_1p3>;
+		vdd_lvs1_2-supply = <&vreg_s4a_1p8>;
+
+		vreg_s3a_1p3: s3 {
+			regulator-name = "vreg_s3a_1p3";
+			regulator-min-microvolt = <1300000>;
+			regulator-max-microvolt = <1300000>;
+
+			/* Required by QCA6174a - vdd-core */
+			regulator-always-on;
+		};
+		vreg_s4a_1p8: s4 {
+			regulator-name = "vreg_s4a_1p8";
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			regulator-allow-set-load;
+
+			/* Required by QCA6174a - vddio */
+			regulator-always-on;
+		};
+		vreg_s5a_2p15: s5 {
+			regulator-name = "vreg_s5a_2p15";
+			regulator-min-microvolt = <2150000>;
+			regulator-max-microvolt = <2150000>;
+		};
+		vreg_s7a_0p8: s7 {
+			regulator-name = "vreg_s7a_0p8";
+			regulator-min-microvolt = <800000>;
+			regulator-max-microvolt = <800000>;
+		};
+		vreg_l1a_1p0: l1 {
+			regulator-name = "vreg_l1a_1p0";
+			regulator-min-microvolt = <1000000>;
+			regulator-max-microvolt = <1000000>;
+		};
+		vreg_l2a_1p25: l2 {
+			regulator-name = "vreg_l2a_1p25";
+			regulator-min-microvolt = <1250000>;
+			regulator-max-microvolt = <1250000>;
+		};
+		vreg_l4a_1p225: l4 {
+			regulator-name = "vreg_l4a_1p225";
+			regulator-min-microvolt = <1225000>;
+			regulator-max-microvolt = <1225000>;
+		};
+		vreg_l6a_1p8: l6 {
+			regulator-name = "vreg_l6a_1p8";
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+		};
+		vreg_l8a_1p8: l8 {
+			regulator-name = "vreg_l8a_1p8";
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+		};
+		vreg_l9a_1p8: l9 {
+			regulator-name = "vreg_l9a_1p8";
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+		};
+		vreg_l10a_1p8: l10 {
+			regulator-name = "vreg_l10a_1p8";
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+		};
+		vreg_l12a_1p8: l12 {
+			regulator-name = "vreg_l12a_1p8";
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			regulator-allow-set-load;
+		};
+		vreg_l13a_2p95: l13 {
+			regulator-name = "vreg_l13a_2p95";
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <2950000>;
+		};
+		vreg_l14a_1p8: l14 {
+			regulator-name = "vreg_l14a_1p8";
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+		};
+		vreg_l15a_1p8: l15 {
+			regulator-name = "vreg_l15a_1p8";
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+		};
+		vreg_l16a_2p7: l16 {
+			regulator-name = "vreg_l16a_2p7";
+			regulator-min-microvolt = <2700000>;
+			regulator-max-microvolt = <2700000>;
+		};
+		vreg_l19a_3p3: l19 {
+			regulator-name = "vreg_l19a_3p3";
+			regulator-min-microvolt = <3000000>;
+			regulator-max-microvolt = <3000000>;
+		};
+		vreg_l20a_2p95: l20 {
+			regulator-name = "vreg_l20a_2p95";
+			regulator-min-microvolt = <2950000>;
+			regulator-max-microvolt = <2950000>;
+			regulator-allow-set-load;
+		};
+		vreg_l21a_2p95: l21 {
+			regulator-name = "vreg_l21a_2p95";
+			regulator-min-microvolt = <3300000>;
+			regulator-max-microvolt = <3300000>;
+			regulator-always-on;
+		};
+		vreg_l23a_2p8: l23 {
+			regulator-name = "vreg_l23a_2p8";
+			regulator-min-microvolt = <2800000>;
+			regulator-max-microvolt = <2800000>;
+		};
+		vreg_l24a_3p075: l24 {
+			regulator-name = "vreg_l24a_3p075";
+			regulator-min-microvolt = <3075000>;
+			regulator-max-microvolt = <3075000>;
+		};
+		vreg_l25a_1p2: l25 {
+			regulator-name = "vreg_l25a_1p2";
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1200000>;
+			regulator-allow-set-load;
+		};
+		vreg_l27a_1p2: l27 {
+			regulator-name = "vreg_l27a_1p2";
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1200000>;
+		};
+		vreg_l28a_0p925: l28 {
+			regulator-name = "vreg_l28a_0p925";
+			regulator-min-microvolt = <925000>;
+			regulator-max-microvolt = <925000>;
+			regulator-allow-set-load;
+		};
+		vreg_l30a_1p8: l30 {
+			regulator-name = "vreg_l30a_1p8";
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+
+			/* Required by QCA6174a - vddio-xtal */
+			regulator-always-on;
+		};
+		vreg_l32a_1p8: l32 {
+			regulator-name = "vreg_l32a_1p8";
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+		};
+		vreg_lvs1a_1p8: lvs1 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+		};
+		vreg_lvs2a_1p8: lvs2 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+		};
+	};
+
+	pmi8994-regulators {
+		compatible = "qcom,rpm-pmi8994-regulators";
+
+		vdd_s1-supply = <&vph_pwr>;
+		vdd_s2-supply = <&vph_pwr>;
+		vdd_s3-supply = <&vph_pwr>;
+		vdd_bst_byp-supply = <&vph_pwr>;
+
+		vreg_s1b_1p025: s1 {
+			regulator-name = "vreg_s1b_1p025";
+			regulator-min-microvolt = <1025000>;
+			regulator-max-microvolt = <1025000>;
+		};
+
+		vph_pwr_bbyp: boost-bypass {
+			regulator-name = "vph_pwr_bbyp";
+			regulator-min-microvolt = <3150000>;
+			regulator-max-microvolt = <3600000>;
+		};
+	};
+};
+
+&pm8994_spmi_regulators {
+	qcom,saw-reg = <&saw3>;
+	s8 {
+		qcom,saw-slave;
+	};
+	s9 {
+		qcom,saw-slave;
+	};
+	s10 {
+		qcom,saw-slave;
+	};
+	vreg_apc_0p8: s11 {
+		qcom,saw-leader;
+		regulator-name = "vreg_apc_0p8";
+		regulator-min-microvolt = <470000>;
+		regulator-max-microvolt = <1140000>;
+		regulator-max-step-microvolt = <150000>;
+		regulator-always-on;
+	};
+};
+
+&pmi8994_spmi_regulators {
+	vdd_gfx: s2 {
+		regulator-name = "vdd_gfx";
+		regulator-min-microvolt = <400000>;
+		regulator-max-microvolt = <1015000>;
+		regulator-enable-ramp-delay = <500>;
+	};
+};
+
+&pm8994_gpios {
+	wlan_en_default: wlan-en-default {
+		pins = "gpio8";
+		function = PMIC_GPIO_FUNC_NORMAL;
+		output-low;
+		qcom,drive-strength = <PMIC_GPIO_STRENGTH_LOW>;
+		power-source = <PM8994_GPIO_S4>;
+		bias-disable;
+	};
+
+	rome_enable_default: rome-enable-default {
+		pins = "gpio9";
+		function = PMIC_GPIO_FUNC_NORMAL;
+		output-high;
+		qcom,drive-strength = <PMIC_GPIO_STRENGTH_LOW>;
+		power-source = <PM8994_GPIO_VPH>;
+	};
+
+	divclk1_default: divclk1_default {
+		pins = "gpio15";
+		function = PMIC_GPIO_FUNC_FUNC1;
+		bias-disable;
+		power-source = <PM8994_GPIO_S4>;
+		qcom,drive-strength = <PMIC_GPIO_STRENGTH_LOW>;
+	};
+
+	divclk4_pin_a: divclk4 {
+		pins = "gpio18";
+		function = PMIC_GPIO_FUNC_FUNC2;
+		bias-disable;
+		power-source = <PM8994_GPIO_S4>;
+	};
+};
+
+&tlmm {
+	mdss_dsi_default: mdss_dsi_default {
+		pins = "gpio8";
+		function = "gpio";
+		drive-strength = <8>;
+		bias-disable;
+	};
+
+	mdss_dsi_sleep: mdss_dsi_sleep {
+		pins = "gpio8";
+		function = "gpio";
+		drive-strength = <2>;
+		bias-pull-down;
+	};
+
+	mdss_te_default: mdss_te_default {
+		pins = "gpio10";
+		function = "mdp_vsync";
+		drive-strength = <2>;
+		bias-pull-down;
+	};
+
+	mdss_te_sleep: mdss_te_sleep {
+		pins = "gpio10";
+		function = "mdp_vsync";
+		drive-strength = <2>;
+		bias-pull-down;
+	};
+
+	nfc_default: nfc_default {
+		pins = "gpio12", "gpio21";
+		function = "gpio";
+		drive-strength = <16>;
+		bias-pull-up;
+	};
+};
diff --git a/arch/arm64/boot/dts/qcom/msm8996-xiaomi-gemini.dts b/arch/arm64/boot/dts/qcom/msm8996-xiaomi-gemini.dts
new file mode 100644
index 000000000000..34f82e06ef53
--- /dev/null
+++ b/arch/arm64/boot/dts/qcom/msm8996-xiaomi-gemini.dts
@@ -0,0 +1,465 @@
+// SPDX-License-Identifier: BSD-3-Clause
+/*
+ * Copyright (c) 2021, Raffaele Tranquillini <raffaele.tranquillini@gmail.com>
+ */
+
+/dts-v1/;
+
+#include "msm8996-xiaomi-common.dtsi"
+#include <dt-bindings/sound/qcom,q6afe.h>
+#include <dt-bindings/sound/qcom,q6asm.h>
+#include <dt-bindings/input/ti-drv260x.h>
+
+/ {
+	model = "Xiaomi Mi 5";
+	compatible = "xiaomi,gemini", "qcom,msm8996";
+	chassis-type = "handset";
+	qcom,msm-id = <246 0x30001>;
+	qcom,pmic-id = <0x20009 0x2000a 0x00 0x00>;
+	qcom,board-id = <31 0>;
+
+	clocks {
+		divclk2_haptics: divclk2 {
+			compatible = "fixed-clock";
+			#clock-cells = <0>;
+			clock-frequency = <32768>;
+			clock-output-names = "divclk2";
+
+			pinctrl-names = "default";
+			pinctrl-0 = <&divclk2_pin_a>;
+		};
+	};
+};
+
+&adsp_pil {
+	firmware-name = "qcom/msm8996/gemini/adsp.mbn";
+};
+
+&blsp2_i2c3 {
+	haptics: drv2604@5a {
+		compatible = "ti,drv2604";
+		reg = <0x5a>;
+		enable-gpio = <&tlmm 93 0x00>;
+		mode = <DRV260X_LRA_MODE>;
+		library-sel = <DRV260X_LIB_LRA>;
+		pinctrl-names = "default","sleep";
+		pinctrl-0 = <&vibrator_default>;
+		pinctrl-1 = <&vibrator_sleep>;
+	};
+
+	lp5562@30 {
+		compatible = "ti,lp5562";
+		reg = <0x30>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		enable-gpio = <&pm8994_gpios 7 1>;
+		clock-mode = /bits/8 <2>;
+		label = "button-backlight";
+
+		led@0 {
+			reg = <0>;
+			chan-name = "button-backlight";
+			led-cur = /bits/ 8 <0x32>;
+			max-cur = /bits/ 8 <0xC8>;
+		};
+
+		led@1 {
+			reg = <0>;
+			chan-name = "button-backlight1";
+			led-cur = /bits/ 8 <0x32>;
+			max-cur = /bits/ 8 <0xC8>;
+		};
+	};
+};
+
+&blsp2_i2c6 {
+	synaptics@20 {
+		compatible = "syna,rmi4-i2c";
+		reg = <0x20>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		interrupt-parent = <&tlmm>;
+		interrupts = <125 IRQ_TYPE_LEVEL_LOW>;
+		vdda-supply = <&vreg_l6a_1p8>;
+		vdd-supply = <&vdd_3v2_tp>;
+		reset-gpios = <&tlmm 89 GPIO_ACTIVE_LOW>;
+
+		pinctrl-names = "default", "sleep";
+		pinctrl-0 = <&touchscreen_default>;
+		pinctrl-1 = <&touchscreen_sleep>;
+	};
+
+};
+
+&dsi0 {
+	status = "okay";
+
+	vdd-supply = <&vreg_l2a_1p25>;
+	vdda-supply = <&vreg_l19a_3p3>;
+	vddio-supply = <&vreg_l14a_1p8>;
+
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&mdss_dsi_default &mdss_te_default>;
+	pinctrl-1 = <&mdss_dsi_sleep &mdss_te_sleep>;
+
+	panel: panel@0 {
+		compatible = "jdi,fhd-r63452";
+		reg = <0>;
+		reset-gpios = <&tlmm 8 GPIO_ACTIVE_LOW>;
+		backlight = <&pmi8994_wled>;
+
+		port {
+			panel_in: endpoint {
+				remote-endpoint = <&dsi0_out>;
+			};
+		};
+	};
+};
+
+&dsi0_out {
+	remote-endpoint = <&panel_in>;
+};
+
+&gpu {
+	zap-shader {
+		firmware-name = "qcom/msm8996/gemini/a530_zap.mbn";
+	};
+};
+
+&pmi8994_wled {
+	status = "okay";
+};
+
+&q6asmdai {
+	dai@0 {
+		reg = <0>;
+	};
+
+	dai@1 {
+		reg = <1>;
+	};
+
+	dai@2 {
+		reg = <2>;
+	};
+};
+
+&sound {
+	compatible = "qcom,apq8096-sndcard";
+	model = "gemini";
+	audio-routing =	"RX_BIAS", "MCLK",
+		"MM_DL1",  "MultiMedia1 Playback",
+		"MM_DL2",  "MultiMedia2 Playback",
+		"MultiMedia3 Capture", "MM_UL3";
+
+	mm1-dai-link {
+		link-name = "MultiMedia1";
+		cpu {
+			sound-dai = <&q6asmdai MSM_FRONTEND_DAI_MULTIMEDIA1>;
+		};
+	};
+
+	mm2-dai-link {
+		link-name = "MultiMedia2";
+		cpu {
+			sound-dai = <&q6asmdai MSM_FRONTEND_DAI_MULTIMEDIA2>;
+		};
+	};
+
+	mm3-dai-link {
+		link-name = "MultiMedia3";
+		cpu {
+			sound-dai = <&q6asmdai MSM_FRONTEND_DAI_MULTIMEDIA3>;
+		};
+	};
+
+	slim-dai-link {
+		link-name = "SLIM Playback";
+		cpu {
+			sound-dai = <&q6afedai SLIMBUS_6_RX>;
+		};
+
+		platform {
+			sound-dai = <&q6routing>;
+		};
+
+		codec {
+			sound-dai = <&wcd9335 6>;
+		};
+	};
+
+	slimcap-dai-link {
+		link-name = "SLIM Capture";
+		cpu {
+			sound-dai = <&q6afedai SLIMBUS_0_TX>;
+		};
+
+		platform {
+			sound-dai = <&q6routing>;
+		};
+
+		codec {
+			sound-dai = <&wcd9335 1>;
+		};
+	};
+};
+
+&venus {
+	firmware-name = "qcom/msm8996/gemini/venus.mbn";
+};
+
+&rpm_requests {
+	pm8994-regulators {
+		vreg_l17a_2p8: l17 {
+			regulator-name = "vreg_l17a_2p8";
+			regulator-min-microvolt = <2500000>;
+			regulator-max-microvolt = <2500000>;
+		};
+		vreg_l29a_2p7: l29 {
+			regulator-name = "vreg_l29a_2p7";
+			regulator-min-microvolt = <2800000>;
+			regulator-max-microvolt = <2800000>;
+		};
+	};
+};
+
+&pm8994_gpios {
+	gpio-line-names =
+		"NC",			/* GPIO_1  */
+		"VOL_UP_N",		/* GPIO_2  */
+		"SPKR_ID",		/* GPIO_3  */
+		"PWM_HAPTICS",		/* GPIO_4  */
+		"INFARED_DRV",		/* GPIO_5  */
+		"NC",			/* GPIO_6  */
+		"KEYPAD_LED_EN",	/* GPIO_7  */
+		"WL_EN",		/* GPIO_8  */
+		"3P3_ENABLE",		/* GPIO_9  */
+		"FP_ID",		/* GPIO_10 */
+		"NC",			/* GPIO_11 */
+		"NC",			/* GPIO_12 */
+		"NC",			/* GPIO_13 */
+		"NC",			/* GPIO_14 */
+		"DIVCLK1_CDC",		/* GPIO_15 */
+		"DIVCLK2_HAPTICS",	/* GPIO_16 */
+		"NC",			/* GPIO_17 */
+		"32KHz_CLK_IN",		/* GPIO_18 */
+		"BT_EN",		/* GPIO_19 */
+		"PMIC_SLB",		/* GPIO_20 */
+		"UIM_BATT_ALARM",	/* GPIO_21 */
+		"NC";			/* GPIO_22 */
+
+	divclk2_pin_a: divclk2 {
+		pins = "gpio16";
+		function = PMIC_GPIO_FUNC_FUNC2;
+		bias-disable;
+		power-source = <PM8994_GPIO_S4>;
+	};
+};
+
+&pm8994_mpps {
+	gpio-line-names =
+		"NC",			/* MPP_1 */
+		"CCI_TIMER1",		/* MPP_2 */
+		"PMIC_SLB",		/* MPP_3 */
+		"EXT_FET_WLED_PWR_EN_N",/* MPP_4 */
+		"NC",			/* MPP_5 */
+		"NC",			/* MPP_6 */
+		"NC",			/* MPP_7 */
+		"NC";			/* MPP_8 */
+};
+
+&pmi8994_gpios {
+	gpio-line-names =
+		"NC",			/* GPIO_1  */
+		"SPKR_PA_RST",		/* GPIO_2  */
+		"NC",			/* GPIO_3  */
+		"NC",			/* GPIO_4  */
+		"NC",			/* GPIO_5  */
+		"NC",			/* GPIO_6  */
+		"NC",			/* GPIO_7  */
+		"NC",			/* GPIO_8  */
+		"NC",			/* GPIO_9  */
+		"NC";			/* GPIO_10 */
+};
+
+&tlmm {
+	gpio-line-names =
+		"ESE_SPI_MOSI",		/* GPIO_0   */
+		"ESE_SPI_MISO",		/* GPIO_1   */
+		"ERR_INT_N",		/* GPIO_2   */
+		"ESE_SPI_CLK",		/* GPIO_3   */
+		"MSM_UART_TX",		/* GPIO_4   */
+		"MSM_UART_RX",		/* GPIO_5   */
+		"NFC_I2C_SDA",		/* GPIO_6   */
+		"NFC_I2C_SCL",		/* GPIO_7   */
+		"LCD0_RESET_N",		/* GPIO_8   */
+		"NFC_IRQ",		/* GPIO_9   */
+		"LCD_TE",		/* GPIO_10  */
+		"LCD_ID_DET1",		/* GPIO_11  */
+		"NFC_DISABLE",		/* GPIO_12  */
+		"CAM_MCLK0",		/* GPIO_13  */
+		"NC",			/* GPIO_14  */
+		"CAM_MCLK2",		/* GPIO_15  */
+		"ESE_PWR_REQ",		/* GPIO_16  */
+		"CCI_I2C_SDA0",		/* GPIO_17  */
+		"CCI_I2C_SCL0",		/* GPIO_18  */
+		"CCI_I2C_SDA1",		/* GPIO_19  */
+		"CCI_I2C_SCL1",		/* GPIO_20  */
+		"NFC_DWL_REQ",		/* GPIO_21  */
+		"CCI_TIMER1",		/* GPIO_22  */
+		"WEBCAM1_RESET_N",	/* GPIO_23  */
+		"ESE_IRQ",		/* GPIO_24  */
+		"NC",			/* GPIO_25  */
+		"WEBCAM1_STANDBY",	/* GPIO_26  */
+		"NC",			/* GPIO_27  */
+		"NC",			/* GPIO_28  */
+		"NC",			/* GPIO_29  */
+		"CAM1_RST_N",		/* GPIO_30  */
+		"NC",			/* GPIO_31  */
+		"NC",			/* GPIO_32  */
+		"NC",			/* GPIO_33  */
+		"FP_DOME_SW",		/* GPIO_34  */
+		"PCI_E0_RST_N",		/* GPIO_35  */
+		"PCI_E0_CLKREQ_N",	/* GPIO_36  */
+		"PCI_E0_WAKE",		/* GPIO_37  */
+		"FM_INT_N",		/* GPIO_38  */
+		"FM_RESET_N",		/* GPIO_39  */
+		"NC",			/* GPIO_40  */
+		"QCA_UART_TXD",		/* GPIO_41  */
+		"QCA_UART_RXD",		/* GPIO_42  */
+		"QCA_UART_CTS",		/* GPIO_43  */
+		"QCA_UART_RTS",		/* GPIO_44  */
+		"MAWC_UART_TX",		/* GPIO_45  */
+		"MAWC_UART_RX",		/* GPIO_46  */
+		"NC",			/* GPIO_47  */
+		"NC",			/* GPIO_48  */
+		"AUDIO_SWITCH_EN",	/* GPIO_49  */
+		"FP_SPI_RST",		/* GPIO_50  */
+		"TYPEC_I2C_SDA",	/* GPIO_51  */
+		"TYPEC_I2C_SCL",	/* GPIO_52  */
+		"CODEC_INT2_N",		/* GPIO_53  */
+		"CODEC_INT1_N",		/* GPIO_54  */
+		"APPS_I2C7_SDA",	/* GPIO_55  */
+		"APPS_I2C7_SCL",	/* GPIO_56  */
+		"FORCE_USB_BOOT",	/* GPIO_57  */
+		"SPKR_I2S_BCK",		/* GPIO_58  */
+		"SPKR_I2S_WS",		/* GPIO_59  */
+		"SPKR_I2S_DOUT",	/* GPIO_60  */
+		"SPKR_I2S_DIN",		/* GPIO_61  */
+		"ESE_RSTN",		/* GPIO_62  */
+		"TYPEC_INT",		/* GPIO_63  */
+		"CODEC_RESET_N",	/* GPIO_64  */
+		"PCM_CLK",		/* GPIO_65  */
+		"PCM_SYNC",		/* GPIO_66  */
+		"PCM_DIN",		/* GPIO_67  */
+		"PCM_DOUT",		/* GPIO_68  */
+		"HIFI_CLK",		/* GPIO_69  */
+		"SLIMBUS_CLK",		/* GPIO_70  */
+		"SLIMBUS_DATA0",	/* GPIO_71  */
+		"SLIMBUS_DATA1",	/* GPIO_72  */
+		"LDO_5V_IN_EN",		/* GPIO_73  */
+		"NC",			/* GPIO_74  */
+		"FM_I2S_CLK",		/* GPIO_75  */
+		"FM_I2S_SYNC",		/* GPIO_76  */
+		"FM_I2S_DATA",		/* GPIO_77  */
+		"FM_STATUS",		/* GPIO_78  */
+		"NC",			/* GPIO_79  */
+		"SENSOR_RESET_N",	/* GPIO_80  */
+		"FP_SPI_MOSI",		/* GPIO_81  */
+		"FP_SPI_MISO",		/* GPIO_82  */
+		"FP_SPI_CS_N",		/* GPIO_83  */
+		"FP_SPI_CLK",		/* GPIO_84  */
+		"NC",			/* GPIO_85  */
+		"CAM_VDD_1P05_EN",	/* GPIO_86  */
+		"MSM_TS_I2C_SDA",	/* GPIO_87  */
+		"MSM_TS_I2C_SCL",	/* GPIO_88  */
+		"TS_RESOUT_N",		/* GPIO_89  */
+		"ESE_SPI_CS_N",		/* GPIO_90  */
+		"NC",			/* GPIO_91  */
+		"NC",			/* GPIO_92  */
+		"HAPTICS_EN",		/* GPIO_93  */
+		"NC",			/* GPIO_94  */
+		"NC",			/* GPIO_95  */
+		"NC",			/* GPIO_96  */
+		"NC",			/* GPIO_97  */
+		"GRFC_1",		/* GPIO_98  */
+		"NC",			/* GPIO_99  */
+		"GRFC_3",		/* GPIO_100 */
+		"GRFC_4",		/* GPIO_101 */
+		"NC",			/* GPIO_102 */
+		"NC",			/* GPIO_103 */
+		"GRFC_7",		/* GPIO_104 */
+		"UIM2_DATA",		/* GPIO_105 */
+		"UIM2_CLK",		/* GPIO_106 */
+		"UIM2_RESET",		/* GPIO_107 */
+		"UIM2_PRESENT",		/* GPIO_108 */
+		"UIM1_DATA",		/* GPIO_109 */
+		"UIM1_CLK",		/* GPIO_110 */
+		"UIM1_RESET",		/* GPIO_111 */
+		"UIM1_PRESENT",		/* GPIO_112 */
+		"UIM_BATT_ALARM",	/* GPIO_113 */
+		"GRFC_8",		/* GPIO_114 */
+		"GRFC_9",		/* GPIO_115 */
+		"TX_GTR_THRES",		/* GPIO_116 */
+		"ACCEL_INT",		/* GPIO_117 */
+		"GYRO_INT",		/* GPIO_118 */
+		"COMPASS_INT",		/* GPIO_119 */
+		"PROXIMITY_INT_N",	/* GPIO_120 */
+		"FP_IRQ",		/* GPIO_121 */
+		"NC",			/* GPIO_122 */
+		"HALL_INTR2",		/* GPIO_123 */
+		"HALL_INTR1",		/* GPIO_124 */
+		"TS_INT_N",		/* GPIO_125 */
+		"NC",			/* GPIO_126 */
+		"GRFC_11",		/* GPIO_127 */
+		"NC",			/* GPIO_128 */
+		"EXT_GPS_LNA_EN",	/* GPIO_129 */
+		"NC",			/* GPIO_130 */
+		"NC",			/* GPIO_131 */
+		"NC",			/* GPIO_132 */
+		"GRFC_14",		/* GPIO_133 */
+		"GSM_TX2_PHASE_D",	/* GPIO_134 */
+		"NC",			/* GPIO_135 */
+		"NC",			/* GPIO_136 */
+		"RFFE3_DATA",		/* GPIO_137 */
+		"RFFE3_CLK",		/* GPIO_138 */
+		"NC",			/* GPIO_139 */
+		"NC",			/* GPIO_140 */
+		"RFFE5_DATA",		/* GPIO_141 */
+		"RFFE5_CLK",		/* GPIO_142 */
+		"NC",			/* GPIO_143 */
+		"COEX_UART_TX",		/* GPIO_144 */
+		"COEX_UART_RX",		/* GPIO_145 */
+		"RFFE2_DATA",		/* GPIO_146 */
+		"RFFE2_CLK",		/* GPIO_147 */
+		"RFFE1_DATA",		/* GPIO_148 */
+		"RFFE1_CLK";		/* GPIO_149 */
+
+	touchscreen_default: touchscreen_default {
+		pins = "gpio89", "gpio125";
+		function = "gpio";
+		drive-strength = <10>;
+		bias-pull-up;
+	};
+
+	touchscreen_sleep: touchscreen_sleep {
+		pins = "gpio89", "gpio125";
+		function = "gpio";
+		drive-strength = <2>;
+		bias-disable;
+	};
+
+	vibrator_default: vibrator_default {
+		pins = "gpio93";
+		function = "gpio";
+		drive-strength = <8>;
+		bias-pull-up;
+	};
+
+	vibrator_sleep: vibrator_sleep {
+		pins = "gpio93";
+		function = "gpio";
+		drive-strength = <2>;
+		bias-disable;
+	};
+};
diff --git a/arch/arm64/boot/dts/qcom/msm8996-xiaomi-scorpio.dts b/arch/arm64/boot/dts/qcom/msm8996-xiaomi-scorpio.dts
new file mode 100644
index 000000000000..e5b8402b1ed6
--- /dev/null
+++ b/arch/arm64/boot/dts/qcom/msm8996-xiaomi-scorpio.dts
@@ -0,0 +1,432 @@
+// SPDX-License-Identifier: BSD-3-Clause
+/*
+ * Copyright (c) 2020, Yassine Oudjana <y.oudjana@protonmail.com>
+ */
+
+/dts-v1/;
+
+#include "msm8996-xiaomi-common.dtsi"
+#include "pmi8996.dtsi"
+#include <dt-bindings/sound/qcom,q6afe.h>
+#include <dt-bindings/sound/qcom,q6asm.h>
+
+/ {
+	model = "Xiaomi Mi Note 2";
+	compatible = "xiaomi,scorpio", "qcom,msm8996";
+	chassis-type = "handset";
+	qcom,msm-id = <305 0x10000>;
+	qcom,board-id = <34 0>;
+
+	chosen {
+		#address-cells = <2>;
+		#size-cells = <2>;
+		ranges;
+
+		framebuffer0: framebuffer@83401000 {
+			compatible = "simple-framebuffer";
+			reg = <0x00 0x83401000 0x00 (1080 * 1920 * 3)>;
+			width = <1080>;
+			height = <1920>;
+			stride = <(1080 * 3)>;
+			format = "r8g8b8";
+
+			/* DSI0 and MDP SMMU clocks */
+			clocks = <&mmcc MDSS_MDP_CLK>,
+				 <&mmcc MMSS_MMAGIC_AHB_CLK>,
+				 <&mmcc MDSS_AHB_CLK>,
+				 <&mmcc MDSS_AXI_CLK>,
+				 <&mmcc MMSS_MISC_AHB_CLK>,
+				 <&mmcc MDSS_BYTE0_CLK>,
+				 <&mmcc MDSS_PCLK0_CLK>,
+				 <&mmcc MDSS_ESC0_CLK>,
+				 <&mmcc SMMU_MDP_AHB_CLK>,
+				 <&mmcc SMMU_MDP_AXI_CLK>;
+
+			/* MDSS power domain */
+			power-domains = <&mmcc MDSS_GDSC>;
+		};
+	};
+
+	reserved-memory {
+		cont_splash_mem: memory@83401000 {
+			reg = <0x0 0x83401000 0x0 (1080 * 1920 * 3)>;
+			no-map;
+		};
+	};
+};
+
+&adsp_pil {
+	firmware-name = "qcom/msm8996/scorpio/adsp.mbn";
+};
+
+&blsp2_i2c6 {
+	touchscreen: atmel-mxt-ts@4a {
+		compatible = "atmel,maxtouch";
+		reg = <0x4a>;
+		interrupt-parent = <&tlmm>;
+		interrupts = <125 IRQ_TYPE_LEVEL_LOW>;
+		vdda-supply = <&vreg_l6a_1p8>;
+		vdd-supply = <&vdd_3v2_tp>;
+		reset-gpios = <&tlmm 75 GPIO_ACTIVE_LOW>;
+
+		pinctrl-names = "default", "sleep";
+		pinctrl-0 = <&touchscreen_default>;
+		pinctrl-1 = <&touchscreen_sleep>;
+	};
+};
+
+&gpu {
+	zap-shader {
+		firmware-name = "qcom/msm8996/scorpio/a530_zap.mbn";
+	};
+};
+
+&mdp_smmu {
+	/*
+	 * Probing this SMMU causes a crash due to writing to some secure
+	 * registers. Disable it for now.
+	 */
+	status = "disabled";
+};
+
+&mdss {
+	/*
+	 * MDSS depends on the MDP SMMU, and probing it alters the bootloader
+	 * configured framebuffer used by simplefb. Disable it for now.
+	 */
+	status = "disabled";
+};
+
+&q6asmdai {
+	dai@0 {
+		reg = <0>;
+	};
+
+	dai@1 {
+		reg = <1>;
+	};
+
+	dai@2 {
+		reg = <2>;
+	};
+};
+
+&sound {
+	compatible = "qcom,apq8096-sndcard";
+	model = "scorpio";
+	audio-routing =	"RX_BIAS", "MCLK";
+
+	mm1-dai-link {
+		link-name = "MultiMedia1";
+		cpu {
+			sound-dai = <&q6asmdai MSM_FRONTEND_DAI_MULTIMEDIA1>;
+		};
+	};
+
+	mm2-dai-link {
+		link-name = "MultiMedia2";
+		cpu {
+			sound-dai = <&q6asmdai MSM_FRONTEND_DAI_MULTIMEDIA2>;
+		};
+	};
+
+	mm3-dai-link {
+		link-name = "MultiMedia3";
+		cpu {
+			sound-dai = <&q6asmdai MSM_FRONTEND_DAI_MULTIMEDIA3>;
+		};
+	};
+
+	slim-dai-link {
+		link-name = "SLIM Playback";
+		cpu {
+			sound-dai = <&q6afedai SLIMBUS_6_RX>;
+		};
+
+		platform {
+			sound-dai = <&q6routing>;
+		};
+
+		codec {
+			sound-dai = <&wcd9335 6>;
+		};
+	};
+
+	slimcap-dai-link {
+		link-name = "SLIM Capture";
+		cpu {
+			sound-dai = <&q6afedai SLIMBUS_0_TX>;
+		};
+
+		platform {
+			sound-dai = <&q6routing>;
+		};
+
+		codec {
+			sound-dai = <&wcd9335 1>;
+		};
+	};
+};
+
+&venus {
+	firmware-name = "qcom/msm8996/scorpio/venus.mbn";
+};
+
+&rpm_requests {
+	pm8994-regulators {
+		vreg_l3a_0p875: l3 {
+			regulator-name = "vreg_l3a_0p875";
+			regulator-min-microvolt = <850000>;
+			regulator-max-microvolt = <1300000>;
+		};
+		vreg_l11a_1p1: l11 {
+			regulator-name = "vreg_l11a_1p1";
+			regulator-min-microvolt = <1100000>;
+			regulator-max-microvolt = <1100000>;
+		};
+		vreg_l17a_2p8: l17 {
+			regulator-name = "vreg_l17a_2p8";
+			regulator-min-microvolt = <2800000>;
+			regulator-max-microvolt = <2800000>;
+		};
+		vreg_l18a_2p8: l18 {
+			regulator-name = "vreg_l18a_2p8";
+			regulator-min-microvolt = <2800000>;
+			regulator-max-microvolt = <2800000>;
+		};
+		vreg_l22a_3p0: l22 {
+			regulator-name = "vreg_l22a_3p0";
+			regulator-min-microvolt = <2950000>;
+			regulator-max-microvolt = <3500000>;
+		};
+		vreg_l29a_2p7: l29 {
+			regulator-name = "vreg_l29a_2p7";
+			regulator-min-microvolt = <2700000>;
+			regulator-max-microvolt = <2700000>;
+		};
+	};
+};
+
+&vdd_gfx {
+	regulator-max-microvolt = <1065000>;
+};
+
+&pm8994_gpios {
+	gpio-line-names =
+		"NC",			/* GPIO_1  */
+		"VOL_UP_N",		/* GPIO_2  */
+		"SPKR_ID",		/* GPIO_3  */
+		"PWM_HAPTICS",		/* GPIO_4  */
+		"INFARED_DRV",		/* GPIO_5  */
+		"NC",			/* GPIO_6  */
+		"KEYPAD_LED_EN_A",	/* GPIO_7  */
+		"WL_EN",		/* GPIO_8  */
+		"3P3_ENABLE",		/* GPIO_9  */
+		"KEYPAD_LED_EN_B",	/* GPIO_10 */
+		"FP_ID",		/* GPIO_11 */
+		"NC",			/* GPIO_12 */
+		"NC",			/* GPIO_13 */
+		"NC",			/* GPIO_14 */
+		"DIVCLK1_CDC",		/* GPIO_15 */
+		"DIVCLK2_HAPTICS",	/* GPIO_16 */
+		"NC",			/* GPIO_17 */
+		"32KHz_CLK_IN",		/* GPIO_18 */
+		"BT_EN",		/* GPIO_19 */
+		"PMIC_SLB",		/* GPIO_20 */
+		"UIM_BATT_ALARM",	/* GPIO_21 */
+		"NC";			/* GPIO_22 */
+};
+
+&pm8994_mpps {
+	gpio-line-names =
+		"VREF_SDC_UIM_APC",	/* MPP_1 */
+		"NC",			/* MPP_2 */
+		"VREF_DACX",		/* MPP_3 */
+		"NC",			/* MPP_4 */
+		"NC",			/* MPP_5 */
+		"STAT_SMB1351",		/* MPP_6 */
+		"NC",			/* MPP_7 */
+		"NC";			/* MPP_8 */
+};
+
+&pmi8994_gpios {
+	gpio-line-names =
+		"NC",			/* GPIO_1  */
+		"SPKR_PA_RST",		/* GPIO_2  */
+		"NC",			/* GPIO_3  */
+		"NC",			/* GPIO_4  */
+		"NC",			/* GPIO_5  */
+		"NC",			/* GPIO_6  */
+		"NC",			/* GPIO_7  */
+		"NC",			/* GPIO_8  */
+		"NC",			/* GPIO_9  */
+		"NC";			/* GPIO_10 */
+};
+
+&tlmm {
+	gpio-line-names =
+		"ESE_SPI_MOSI",		/* GPIO_0   */
+		"ESE_SPI_MISO",		/* GPIO_1   */
+		"NC",			/* GPIO_2   */
+		"ESE_SPI_CLK",		/* GPIO_3   */
+		"MSM_UART_TX",		/* GPIO_4   */
+		"MSM_UART_RX",		/* GPIO_5   */
+		"NFC_I2C_SDA",		/* GPIO_6   */
+		"NFC_I2C_SCL",		/* GPIO_7   */
+		"OLED_RESET_N",		/* GPIO_8   */
+		"NFC_IRQ",		/* GPIO_9   */
+		"OLED_TE",		/* GPIO_10  */
+		"OLED_ID_DET1",		/* GPIO_11  */
+		"NFC_DISABLE",		/* GPIO_12  */
+		"CAM_MCLK0",		/* GPIO_13  */
+		"OLED_ID_DET2",		/* GPIO_14  */
+		"CAM_MCLK2",		/* GPIO_15  */
+		"ESE_PWR_REQ",		/* GPIO_16  */
+		"CCI_I2C_SDA0",		/* GPIO_17  */
+		"CCI_I2C_SCL0",		/* GPIO_18  */
+		"CCI_I2C_SDA1",		/* GPIO_19  */
+		"CCI_I2C_SCL1",		/* GPIO_20  */
+		"NFC_DWL_REQ",		/* GPIO_21  */
+		"CCI_TIMER1",		/* GPIO_22  */
+		"WEBCAM1_RESET_N",	/* GPIO_23  */
+		"ESE_IRQ",		/* GPIO_24  */
+		"NC",			/* GPIO_25  */
+		"WEBCAM1_STANDBY",	/* GPIO_26  */
+		"NC",			/* GPIO_27  */
+		"NC",			/* GPIO_28  */
+		"OLED_ERR_FG",		/* GPIO_29  */
+		"CAM1_RST_N",		/* GPIO_30  */
+		"HIFI_SW_MUTE",		/* GPIO_31  */
+		"NC",			/* GPIO_32  */
+		"NC",			/* GPIO_33  */
+		"FP_DOME_SW",		/* GPIO_34  */
+		"PCI_E0_RST_N",		/* GPIO_35  */
+		"PCI_E0_CLKREQ_N",	/* GPIO_36  */
+		"PCI_E0_WAKE",		/* GPIO_37  */
+		"OV_PWDN",		/* GPIO_38  */
+		"NC",			/* GPIO_39  */
+		"VDDR_1P6_EN",		/* GPIO_40  */
+		"QCA_UART_TXD",		/* GPIO_41  */
+		"QCA_UART_RXD",		/* GPIO_42  */
+		"QCA_UART_CTS",		/* GPIO_43  */
+		"QCA_UART_RTS",		/* GPIO_44  */
+		"MAWC_UART_TX",		/* GPIO_45  */
+		"MAWC_UART_RX",		/* GPIO_46  */
+		"NC",			/* GPIO_47  */
+		"NC",			/* GPIO_48  */
+		"AUDIO_SWITCH_EN",	/* GPIO_49  */
+		"FP_SPI_RST",		/* GPIO_50  */
+		"TYPEC_I2C_SDA",	/* GPIO_51  */
+		"TYPEC_I2C_SCL",	/* GPIO_52  */
+		"CODEC_INT2_N",		/* GPIO_53  */
+		"CODEC_INT1_N",		/* GPIO_54  */
+		"APPS_I2C7_SDA",	/* GPIO_55  */
+		"APPS_I2C7_SCL",	/* GPIO_56  */
+		"FORCE_USB_BOOT",	/* GPIO_57  */
+		"SPKR_I2S_BCK",		/* GPIO_58  */
+		"SPKR_I2S_WS",		/* GPIO_59  */
+		"SPKR_I2S_DOUT",	/* GPIO_60  */
+		"SPKR_I2S_DIN",		/* GPIO_61  */
+		"ESE_RSTN",		/* GPIO_62  */
+		"TYPEC_INT",		/* GPIO_63  */
+		"CODEC_RESET_N",	/* GPIO_64  */
+		"PCM_CLK",		/* GPIO_65  */
+		"PCM_SYNC",		/* GPIO_66  */
+		"PCM_DIN",		/* GPIO_67  */
+		"PCM_DOUT",		/* GPIO_68  */
+		"CDC_44K1_CLK",		/* GPIO_69  */
+		"SLIMBUS_CLK",		/* GPIO_70  */
+		"SLIMBUS_DATA0",	/* GPIO_71  */
+		"SLIMBUS_DATA1",	/* GPIO_72  */
+		"LDO_5V_IN_EN",		/* GPIO_73  */
+		"NC",			/* GPIO_74  */
+		"TSP_RST_N",		/* GPIO_75  */
+		"NC",			/* GPIO_76  */
+		"TOUCHKEY_INT",		/* GPIO_77  */
+		"SPKR_I2S_MCLK",	/* GPIO_78  */
+		"SPKR_PA_INT",		/* GPIO_79  */
+		"SENSOR_RESET_N",	/* GPIO_80  */
+		"FP_SPI_MOSI",		/* GPIO_81  */
+		"FP_SPI_MISO",		/* GPIO_82  */
+		"FP_SPI_CS_N",		/* GPIO_83  */
+		"FP_SPI_CLK",		/* GPIO_84  */
+		"HIFI_SD",		/* GPIO_85  */
+		"CAM_VDD_1P05_EN",	/* GPIO_86  */
+		"MSM_TS_I2C_SDA",	/* GPIO_87  */
+		"MSM_TS_I2C_SCL",	/* GPIO_88  */
+		"NC",			/* GPIO_89  */
+		"ESE_SPI_CS_N",		/* GPIO_90  */
+		"NC",			/* GPIO_91  */
+		"NC",			/* GPIO_92  */
+		"NC",			/* GPIO_93  */
+		"NC",			/* GPIO_94  */
+		"NC",			/* GPIO_95  */
+		"NC",			/* GPIO_96  */
+		"GRFC_0",		/* GPIO_97  */
+		"GRFC_1",		/* GPIO_98  */
+		"NC",			/* GPIO_99  */
+		"GRFC_3",		/* GPIO_100 */
+		"GRFC_4",		/* GPIO_101 */
+		"NC",			/* GPIO_102 */
+		"NC",			/* GPIO_103 */
+		"GRFC_7",		/* GPIO_104 */
+		"UIM2_DATA",		/* GPIO_105 */
+		"UIM2_CLK",		/* GPIO_106 */
+		"UIM2_RESET",		/* GPIO_107 */
+		"UIM2_PRESENT",		/* GPIO_108 */
+		"UIM1_DATA",		/* GPIO_109 */
+		"UIM1_CLK",		/* GPIO_110 */
+		"UIM1_RESET",		/* GPIO_111 */
+		"UIM1_PRESENT",		/* GPIO_112 */
+		"UIM_BATT_ALARM",	/* GPIO_113 */
+		"GRFC_8",		/* GPIO_114 */
+		"GRFC_9",		/* GPIO_115 */
+		"TX_GTR_THRES",		/* GPIO_116 */
+		"ACC_INT",		/* GPIO_117 */
+		"GYRO_INT",		/* GPIO_118 */
+		"COMPASS_INT",		/* GPIO_119 */
+		"PROXIMITY_INT_N",	/* GPIO_120 */
+		"FP_IRQ",		/* GPIO_121 */
+		"TSP_TA",		/* GPIO_122 */
+		"HALL_INTR2",		/* GPIO_123 */
+		"HALL_INTR1",		/* GPIO_124 */
+		"TS_INT_N",		/* GPIO_125 */
+		"NC",			/* GPIO_126 */
+		"GRFC_11",		/* GPIO_127 */
+		"HIFI_PWR_EN",		/* GPIO_128 */
+		"EXT_GPS_LNA_EN",	/* GPIO_129 */
+		"NC",			/* GPIO_130 */
+		"NC",			/* GPIO_131 */
+		"NC",			/* GPIO_132 */
+		"GRFC_14",		/* GPIO_133 */
+		"GSM_TX2_PHASE_D",	/* GPIO_134 */
+		"HIFI_SW_SEL",		/* GPIO_135 */
+		"GRFC_15",		/* GPIO_136 */
+		"RFFE3_DATA",		/* GPIO_137 */
+		"RFFE3_CLK",		/* GPIO_138 */
+		"NC",			/* GPIO_139 */
+		"NC",			/* GPIO_140 */
+		"RFFE5_DATA",		/* GPIO_141 */
+		"RFFE5_CLK",		/* GPIO_142 */
+		"NC",			/* GPIO_143 */
+		"COEX_UART_TX",		/* GPIO_144 */
+		"COEX_UART_RX",		/* GPIO_145 */
+		"RFFE2_DATA",		/* GPIO_146 */
+		"RFFE2_CLK",		/* GPIO_147 */
+		"RFFE1_DATA",		/* GPIO_148 */
+		"RFFE1_CLK";		/* GPIO_149 */
+
+	touchscreen_default: touchscreen_default {
+		pins = "gpio75", "gpio125";
+		function = "gpio";
+		drive-strength = <10>;
+		bias-pull-up;
+	};
+
+	touchscreen_sleep: touchscreen_sleep {
+		pins = "gpio75", "gpio125";
+		function = "gpio";
+		drive-strength = <2>;
+		bias-disable;
+	};
+};
diff --git a/arch/arm64/boot/dts/qcom/msm8996.dtsi b/arch/arm64/boot/dts/qcom/msm8996.dtsi
index 52df22ab3f6a..bccc2d0b35a8 100644
--- a/arch/arm64/boot/dts/qcom/msm8996.dtsi
+++ b/arch/arm64/boot/dts/qcom/msm8996.dtsi
@@ -582,7 +582,6 @@
 		pcie_phy: phy@34000 {
 			compatible = "qcom,msm8996-qmp-pcie-phy";
 			reg = <0x00034000 0x488>;
-			#clock-cells = <1>;
 			#address-cells = <1>;
 			#size-cells = <1>;
 			ranges;
@@ -598,12 +597,13 @@
 			reset-names = "phy", "common", "cfg";
 			status = "disabled";
 
-			pciephy_0: lane@35000 {
+			pciephy_0: phy@35000 {
 				reg = <0x00035000 0x130>,
 				      <0x00035200 0x200>,
 				      <0x00035400 0x1dc>;
 				#phy-cells = <0>;
 
+				#clock-cells = <1>;
 				clock-output-names = "pcie_0_pipe_clk_src";
 				clocks = <&gcc GCC_PCIE_0_PIPE_CLK>;
 				clock-names = "pipe0";
@@ -611,7 +611,7 @@
 				reset-names = "lane0";
 			};
 
-			pciephy_1: lane@36000 {
+			pciephy_1: phy@36000 {
 				reg = <0x00036000 0x130>,
 				      <0x00036200 0x200>,
 				      <0x00036400 0x1dc>;
@@ -624,7 +624,7 @@
 				reset-names = "lane1";
 			};
 
-			pciephy_2: lane@37000 {
+			pciephy_2: phy@37000 {
 				reg = <0x00037000 0x130>,
 				      <0x00037200 0x200>,
 				      <0x00037400 0x1dc>;
@@ -638,7 +638,7 @@
 			};
 		};
 
-		rpm_msg_ram: memory@68000 {
+		rpm_msg_ram: sram@68000 {
 			compatible = "qcom,rpm-msg-ram";
 			reg = <0x00068000 0x6000>;
 		};
@@ -705,6 +705,28 @@
 			#thermal-sensor-cells = <1>;
 		};
 
+		cryptobam: dma@644000 {
+			compatible = "qcom,bam-v1.7.0";
+			reg = <0x00644000 0x24000>;
+			interrupts = <GIC_SPI 206 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&gcc GCC_CE1_CLK>;
+			clock-names = "bam_clk";
+			#dma-cells = <1>;
+			qcom,ee = <0>;
+			qcom,controlled-remotely = <1>;
+		};
+
+		crypto: crypto@67a000 {
+			compatible = "qcom,crypto-v5.4";
+			reg = <0x0067a000 0x6000>;
+			clocks = <&gcc GCC_CE1_AHB_CLK>,
+				 <&gcc GCC_CE1_AXI_CLK>,
+				 <&gcc GCC_CE1_CLK>;
+			clock-names = "iface", "bus", "core";
+			dmas = <&cryptobam 6>, <&cryptobam 7>;
+			dma-names = "rx", "tx";
+		};
+
 		tcsr_mutex_regs: syscon@740000 {
 			compatible = "syscon";
 			reg = <0x00740000 0x40000>;
@@ -1211,6 +1233,20 @@
 				};
 			};
 
+			blsp1_uart2_default: blsp1-uart2-default {
+				pins = "gpio41", "gpio42", "gpio43", "gpio44";
+				function = "blsp_uart2";
+				drive-strength = <16>;
+				bias-disable;
+			};
+
+			blsp1_uart2_sleep: blsp1-uart2-sleep {
+				pins = "gpio41", "gpio42", "gpio43", "gpio44";
+				function = "gpio";
+				drive-strength = <2>;
+				bias-disable;
+			};
+
 			blsp1_i2c3_default: blsp1-i2c2-default {
 				pins = "gpio47", "gpio48";
 				function = "blsp_i2c3";
@@ -1239,6 +1275,20 @@
 				bias-disable;
 			};
 
+			blsp2_i2c3_default: blsp2-i2c3 {
+				pins = "gpio51", "gpio52";
+				function = "blsp_i2c9";
+				drive-strength = <16>;
+				bias-disable;
+			};
+
+			blsp2_i2c3_sleep: blsp2-i2c3-sleep {
+				pins = "gpio51", "gpio52";
+				function = "gpio";
+				drive-strength = <2>;
+				bias-disable;
+			};
+
 			wcd_intr_default: wcd-intr-default{
 				pins = "gpio54";
 				function = "gpio";
@@ -1495,6 +1545,11 @@
 			};
 		};
 
+		sram@290000 {
+			compatible = "qcom,rpm-stats";
+			reg = <0x00290000 0x10000>;
+		};
+
 		spmi_bus: qcom,spmi@400f000 {
 			compatible = "qcom,spmi-pmic-arb";
 			reg = <0x0400f000 0x1000>,
@@ -1746,7 +1801,7 @@
 			reset-names = "ufsphy";
 			status = "disabled";
 
-			ufsphy_lane: lanes@627400 {
+			ufsphy_lane: phy@627400 {
 				reg = <0x627400 0x12c>,
 				      <0x627600 0x200>,
 				      <0x627c00 0x1b4>;
@@ -2586,7 +2641,6 @@
 		usb3phy: phy@7410000 {
 			compatible = "qcom,msm8996-qmp-usb3-phy";
 			reg = <0x07410000 0x1c4>;
-			#clock-cells = <1>;
 			#address-cells = <1>;
 			#size-cells = <1>;
 			ranges;
@@ -2601,12 +2655,13 @@
 			reset-names = "phy", "common";
 			status = "disabled";
 
-			ssusb_phy_0: lane@7410200 {
+			ssusb_phy_0: phy@7410200 {
 				reg = <0x07410200 0x200>,
 				      <0x07410400 0x130>,
 				      <0x07410600 0x1a8>;
 				#phy-cells = <0>;
 
+				#clock-cells = <1>;
 				clock-output-names = "usb3_phy_pipe_clk_src";
 				clocks = <&gcc GCC_USB3_PHY_PIPE_CLK>;
 				clock-names = "pipe0";
@@ -2686,7 +2741,7 @@
 			status = "disabled";
 		 };
 
-		blsp1_dma: dma@7544000 {
+		blsp1_dma: dma-controller@7544000 {
 			compatible = "qcom,bam-v1.7.0";
 			reg = <0x07544000 0x2b000>;
 			interrupts = <GIC_SPI 238 IRQ_TYPE_LEVEL_HIGH>;
@@ -2704,6 +2759,9 @@
 			clocks = <&gcc GCC_BLSP1_UART2_APPS_CLK>,
 				 <&gcc GCC_BLSP1_AHB_CLK>;
 			clock-names = "core", "iface";
+			pinctrl-names = "default", "sleep";
+			pinctrl-0 = <&blsp1_uart2_default>;
+			pinctrl-1 = <&blsp1_uart2_sleep>;
 			dmas = <&blsp1_dma 2>, <&blsp1_dma 3>;
 			dma-names = "tx", "rx";
 			status = "disabled";
@@ -2743,7 +2801,7 @@
 			status = "disabled";
 		};
 
-		blsp2_dma: dma@7584000 {
+		blsp2_dma: dma-controller@7584000 {
 			compatible = "qcom,bam-v1.7.0";
 			reg = <0x07584000 0x2b000>;
 			interrupts = <GIC_SPI 239 IRQ_TYPE_LEVEL_HIGH>;
@@ -2808,6 +2866,24 @@
 			status = "disabled";
 		};
 
+		blsp2_i2c3: i2c@75b7000 {
+			compatible = "qcom,i2c-qup-v2.2.1";
+			reg = <0x075b7000 0x1000>;
+			interrupts = <GIC_SPI 103 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&gcc GCC_BLSP2_AHB_CLK>,
+				<&gcc GCC_BLSP2_QUP3_I2C_APPS_CLK>;
+			clock-names = "iface", "core";
+			clock-frequency = <400000>;
+			pinctrl-names = "default", "sleep";
+			pinctrl-0 = <&blsp2_i2c3_default>;
+			pinctrl-1 = <&blsp2_i2c3_sleep>;
+			dmas = <&blsp2_dma 16>, <&blsp2_dma 17>;
+			dma-names = "tx", "rx";
+			#address-cells = <1>;
+			#size-cells = <0>;
+			status = "disabled";
+		};
+
 		blsp2_i2c5: i2c@75b9000 {
 			compatible = "qcom,i2c-qup-v2.2.1";
 			reg = <0x75b9000 0x1000>;
diff --git a/arch/arm64/boot/dts/qcom/msm8998-asus-novago-tp370ql.dts b/arch/arm64/boot/dts/qcom/msm8998-asus-novago-tp370ql.dts
index db5821be1e2f..e204b7050441 100644
--- a/arch/arm64/boot/dts/qcom/msm8998-asus-novago-tp370ql.dts
+++ b/arch/arm64/boot/dts/qcom/msm8998-asus-novago-tp370ql.dts
@@ -8,6 +8,7 @@
 / {
 	model = "Asus NovaGo TP370QL";
 	compatible = "asus,novago-tp370ql", "qcom,msm8998";
+	chassis-type = "convertible";
 };
 
 &blsp1_i2c6 {
diff --git a/arch/arm64/boot/dts/qcom/msm8998-clamshell.dtsi b/arch/arm64/boot/dts/qcom/msm8998-clamshell.dtsi
index 125d7923d713..3f60575a351c 100644
--- a/arch/arm64/boot/dts/qcom/msm8998-clamshell.dtsi
+++ b/arch/arm64/boot/dts/qcom/msm8998-clamshell.dtsi
@@ -313,6 +313,8 @@
 
 &ufsphy {
 	status = "okay";
+	vdda-phy-supply = <&vreg_l1a_0p875>;
+	vdda-pll-supply = <&vreg_l2a_1p2>;
 };
 
 &usb3 {
diff --git a/arch/arm64/boot/dts/qcom/msm8998-fxtec-pro1.dts b/arch/arm64/boot/dts/qcom/msm8998-fxtec-pro1.dts
new file mode 100644
index 000000000000..3d495ce3f46a
--- /dev/null
+++ b/arch/arm64/boot/dts/qcom/msm8998-fxtec-pro1.dts
@@ -0,0 +1,320 @@
+// SPDX-License-Identifier: BSD-3-Clause
+/*
+ * Copyright (c) 2021, AngeloGioacchino Del Regno
+ *                     <angelogioacchino.delregno@somainline.org>
+ */
+
+/dts-v1/;
+
+#include "msm8998-mtp.dtsi"
+
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/leds/common.h>
+#include <dt-bindings/pinctrl/qcom,pmic-gpio.h>
+
+/ {
+	model = "F(x)tec Pro1 (QX1000)";
+	compatible = "fxtec,pro1", "qcom,msm8998";
+	chassis-type = "handset";
+	qcom,board-id = <0x02000b 0x10>;
+
+	/*
+	 * Until we hook up type-c detection, we
+	 * have to stick with this. But it works.
+	 */
+	extcon_usb: extcon-usb {
+		compatible = "linux,extcon-usb-gpio";
+		id-gpio = <&tlmm 38 GPIO_ACTIVE_HIGH>;
+	};
+
+	gpio-hall-sensors {
+		compatible = "gpio-keys";
+		input-name = "hall-sensors";
+		label = "Hall sensors";
+		pinctrl-names = "default";
+		pinctrl-0 = <&hall_sensor1_default>;
+
+		hall-sensor1 {
+			label = "Keyboard Hall Sensor";
+			gpios = <&tlmm 124 GPIO_ACTIVE_HIGH>;
+			debounce-interval = <15>;
+			gpio-key,wakeup;
+			linux,input-type = <EV_SW>;
+			linux,code = <SW_KEYPAD_SLIDE>;
+		};
+	};
+
+	gpio-kb-extra-keys {
+		compatible = "gpio-keys";
+		input-name = "extra-kb-keys";
+		label = "Keyboard extra keys";
+		pinctrl-names = "default";
+		pinctrl-0 = <&gpio_kb_pins_extra>;
+
+		home {
+			label = "Home";
+			gpios = <&tlmm 21 GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_HOMEPAGE>;
+			debounce-interval = <15>;
+			linux,can-disable;
+		};
+
+		super-l {
+			label = "Super Left";
+			gpios = <&tlmm 32 GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_FN>;
+			debounce-interval = <15>;
+			linux,can-disable;
+		};
+
+		super-r {
+			label = "Super Right";
+			gpios = <&tlmm 33 GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_FN>;
+			debounce-interval = <15>;
+			linux,can-disable;
+		};
+
+		shift {
+			label = "Shift";
+			gpios = <&tlmm 114 GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_RIGHTSHIFT>;
+			debounce-interval = <15>;
+			linux,can-disable;
+		};
+
+		ctrl {
+			label = "Ctrl";
+			gpios = <&tlmm 128 GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_LEFTCTRL>;
+			debounce-interval = <15>;
+			linux,can-disable;
+		};
+
+		alt {
+			label = "Alt";
+			gpios = <&tlmm 129 GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_LEFTALT>;
+			debounce-interval = <15>;
+			linux,can-disable;
+		};
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+		input-name = "side-buttons";
+		label = "Side buttons";
+		#address-cells = <1>;
+		#size-cells = <0>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&vol_up_pin_a>, <&cam_focus_pin_a>,
+			    <&cam_snapshot_pin_a>;
+		vol-up {
+			label = "Volume Up";
+			gpios = <&pm8998_gpio 6 GPIO_ACTIVE_LOW>;
+			linux,input-type = <EV_KEY>;
+			linux,code = <KEY_VOLUMEUP>;
+			gpio-key,wakeup;
+			debounce-interval = <15>;
+		};
+
+		camera-snapshot {
+			label = "Camera Snapshot";
+			gpios = <&pm8998_gpio 7 GPIO_ACTIVE_LOW>;
+			linux,input-type = <EV_KEY>;
+			linux,code = <KEY_CAMERA>;
+			debounce-interval = <15>;
+		};
+
+		camera-focus {
+			label = "Camera Focus";
+			gpios = <&pm8998_gpio 8 GPIO_ACTIVE_LOW>;
+			linux,input-type = <EV_KEY>;
+			linux,code = <KEY_CAMERA_FOCUS>;
+			debounce-interval = <15>;
+		};
+	};
+
+	keyboard-leds {
+		compatible = "gpio-leds";
+
+		backlight {
+			color = <LED_COLOR_ID_WHITE>;
+			default-state = "off";
+			function = LED_FUNCTION_KBD_BACKLIGHT;
+			gpios = <&tlmm 16 GPIO_ACTIVE_HIGH>;
+			label = "white:kbd_backlight";
+			retain-state-suspended;
+		};
+
+		caps-lock {
+			color = <LED_COLOR_ID_YELLOW>;
+			default-state = "off";
+			function = LED_FUNCTION_CAPSLOCK;
+			gpios = <&tlmm 26 GPIO_ACTIVE_HIGH>;
+			label = "yellow:capslock";
+			linux,default-trigger = "kbd-capslock";
+		};
+	};
+
+	reserved-memory {
+		cont_splash_mem: memory@9d400000 {
+			reg = <0x0 0x9d400000 0x0 0x2000000>;
+			no-map;
+		};
+
+		zap_shader_region: memory@f6400000 {
+			compatible = "shared-dma-pool";
+			reg = <0x0 0xf6400000 0x0 0x2000>;
+			no-map;
+		};
+
+		ramoops@ffc00000 {
+			compatible = "ramoops";
+			reg = <0x0 0xffc00000 0x0 0x100000>;
+			console-size = <0x60000>;
+			ecc-size = <16>;
+			ftrace-size = <0x10000>;
+			pmsg-size = <0x20000>;
+			record-size = <0x10000>;
+		};
+	};
+
+	ts_vio_vreg: ts-vio-vreg {
+		compatible = "regulator-fixed";
+		regulator-name = "ts_vio_reg";
+		startup-delay-us = <2>;
+		enable-active-high;
+		gpio = <&tlmm 81 GPIO_ACTIVE_HIGH>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&ts_vio_default>;
+		regulator-always-on;
+	};
+};
+
+&blsp2_i2c1 {
+	status = "ok";
+
+	touchscreen@14 {
+		compatible = "goodix,gt9286";
+		reg = <0x14>;
+		interrupt-parent = <&tlmm>;
+		interrupts = <125 IRQ_TYPE_LEVEL_LOW>;
+		reset-gpios = <&tlmm 89 GPIO_ACTIVE_HIGH>;
+		AVDD28-supply = <&vreg_l28_3p0>;
+		VDDIO-supply = <&ts_vio_vreg>;
+		pinctrl-names = "active";
+		pinctrl-0 = <&ts_rst_n>, <&ts_int_n>;
+	};
+};
+
+&mmcc {
+	status = "ok";
+};
+
+&mmss_smmu {
+	status = "ok";
+};
+
+&pm8998_gpio {
+	vol_up_pin_a: vol-up-active {
+		pins = "gpio6";
+		function = "normal";
+		bias-pull-up;
+		input-enable;
+		qcom,drive-strength = <PMIC_GPIO_STRENGTH_NO>;
+	};
+
+	cam_focus_pin_a: cam-focus-btn-active {
+		pins = "gpio7";
+		function = "normal";
+		bias-pull-up;
+		input-enable;
+		qcom,drive-strength = <PMIC_GPIO_STRENGTH_NO>;
+	};
+
+	cam_snapshot_pin_a: cam-snapshot-btn-active {
+		pins = "gpio8";
+		function = "normal";
+		bias-pull-up;
+		input-enable;
+		qcom,drive-strength = <PMIC_GPIO_STRENGTH_NO>;
+	};
+};
+
+&pm8998_pon {
+	resin {
+		compatible = "qcom,pm8941-resin";
+		interrupts = <GIC_SPI 0x8 1 IRQ_TYPE_EDGE_BOTH>;
+		bias-pull-up;
+		debounce = <15625>;
+		linux,code = <KEY_VOLUMEDOWN>;
+	};
+};
+
+&tlmm {
+	gpio-reserved-ranges = <0 4>;
+
+	mdp_vsync_n: mdp-vsync-n {
+		pins = "gpio10";
+		function = "mdp_vsync_a";
+		bias-pull-down;
+		drive-strength = <2>;
+	};
+
+	gpio_kb_pins_extra: gpio-kb-pins-extra {
+		pins = "gpio21", "gpio32", "gpio33", "gpio114",
+		       "gpio128", "gpio129";
+		function = "gpio";
+		drive-strength = <2>;
+		bias-pull-up;
+	};
+
+	ts_vio_default: ts-vio-def {
+		pins = "gpio81";
+		function = "gpio";
+		bias-disable;
+		drive-strength = <2>;
+	};
+
+	ts_rst_n: ts-rst-n {
+		pins = "gpio89";
+		function = "gpio";
+		bias-pull-up;
+		drive-strength = <8>;
+	};
+
+	hall_sensor1_default: hall-sensor1-def {
+		pins = "gpio124";
+		function = "gpio";
+		bias-disable;
+		drive-strength = <2>;
+		input-enable;
+	};
+
+	ts_int_n: ts-int-n {
+		pins = "gpio125";
+		function = "gpio";
+		bias-disable;
+		drive-strength = <8>;
+	};
+};
+
+&ufshc {
+	status = "ok";
+};
+
+&ufsphy {
+	status = "ok";
+};
+
+&usb3_dwc3 {
+	dr_mode = "peripheral";
+	extcon = <&extcon_usb>;
+};
+
+/* GT9286 analog supply */
+&vreg_l28_3p0 {
+	regulator-min-microvolt = <2800000>;
+	regulator-max-microvolt = <2800000>;
+};
diff --git a/arch/arm64/boot/dts/qcom/msm8998-hp-envy-x2.dts b/arch/arm64/boot/dts/qcom/msm8998-hp-envy-x2.dts
index 24073127091f..1eb406b43fd7 100644
--- a/arch/arm64/boot/dts/qcom/msm8998-hp-envy-x2.dts
+++ b/arch/arm64/boot/dts/qcom/msm8998-hp-envy-x2.dts
@@ -8,6 +8,7 @@
 / {
 	model = "HP Envy x2";
 	compatible = "hp,envy-x2", "qcom,msm8998";
+	chassis-type = "convertible";
 };
 
 &blsp1_i2c6 {
diff --git a/arch/arm64/boot/dts/qcom/msm8998-lenovo-miix-630.dts b/arch/arm64/boot/dts/qcom/msm8998-lenovo-miix-630.dts
index 89492ed5196c..f55f6f3e3e5d 100644
--- a/arch/arm64/boot/dts/qcom/msm8998-lenovo-miix-630.dts
+++ b/arch/arm64/boot/dts/qcom/msm8998-lenovo-miix-630.dts
@@ -8,6 +8,7 @@
 / {
 	model = "Lenovo Miix 630";
 	compatible = "lenovo,miix-630", "qcom,msm8998";
+	chassis-type = "convertible";
 };
 
 &blsp1_i2c6 {
diff --git a/arch/arm64/boot/dts/qcom/msm8998-mtp.dtsi b/arch/arm64/boot/dts/qcom/msm8998-mtp.dtsi
index a1d15eab8553..af67c641df4e 100644
--- a/arch/arm64/boot/dts/qcom/msm8998-mtp.dtsi
+++ b/arch/arm64/boot/dts/qcom/msm8998-mtp.dtsi
@@ -371,10 +371,6 @@
 	vdda-phy-supply = <&vreg_l1a_0p875>;
 	vdda-pll-supply = <&vreg_l2a_1p2>;
 	vddp-ref-clk-supply = <&vreg_l26a_1p2>;
-	vdda-phy-max-microamp = <51400>;
-	vdda-pll-max-microamp = <14600>;
-	vddp-ref-clk-max-microamp = <100>;
-	vddp-ref-clk-always-on;
 };
 
 &usb3 {
diff --git a/arch/arm64/boot/dts/qcom/msm8998-oneplus-cheeseburger.dts b/arch/arm64/boot/dts/qcom/msm8998-oneplus-cheeseburger.dts
index 66b9297588ab..9563eb62db88 100644
--- a/arch/arm64/boot/dts/qcom/msm8998-oneplus-cheeseburger.dts
+++ b/arch/arm64/boot/dts/qcom/msm8998-oneplus-cheeseburger.dts
@@ -11,6 +11,7 @@
 / {
 	model = "OnePlus 5";
 	compatible = "oneplus,cheeseburger", "qcom,msm8998";
+	chassis-type = "handset";
 	/* Required for bootloader to select correct board */
 	qcom,board-id = <8 0 16859 23>;
 
diff --git a/arch/arm64/boot/dts/qcom/msm8998-oneplus-common.dtsi b/arch/arm64/boot/dts/qcom/msm8998-oneplus-common.dtsi
index 0f5c7828a901..654188027f79 100644
--- a/arch/arm64/boot/dts/qcom/msm8998-oneplus-common.dtsi
+++ b/arch/arm64/boot/dts/qcom/msm8998-oneplus-common.dtsi
@@ -480,10 +480,6 @@
 	vdda-phy-supply = <&vreg_l1a_0p875>;
 	vdda-pll-supply = <&vreg_l2a_1p2>;
 	vddp-ref-clk-supply = <&vreg_l26a_1p2>;
-	vdda-phy-max-microamp = <51400>;
-	vdda-pll-max-microamp = <14600>;
-	vddp-ref-clk-max-microamp = <100>;
-	vddp-ref-clk-always-on;
 };
 
 &usb3 {
diff --git a/arch/arm64/boot/dts/qcom/msm8998-oneplus-dumpling.dts b/arch/arm64/boot/dts/qcom/msm8998-oneplus-dumpling.dts
index 544b9b0ae44b..5d0dabbaee4e 100644
--- a/arch/arm64/boot/dts/qcom/msm8998-oneplus-dumpling.dts
+++ b/arch/arm64/boot/dts/qcom/msm8998-oneplus-dumpling.dts
@@ -10,6 +10,7 @@
 / {
 	model = "OnePlus 5T";
 	compatible = "oneplus,dumpling", "qcom,msm8998";
+	chassis-type = "handset";
 	/* Required for bootloader to select correct board */
 	qcom,board-id = <8 0 17801 43>;
 };
diff --git a/arch/arm64/boot/dts/qcom/msm8998-sony-xperia-yoshino-lilac.dts b/arch/arm64/boot/dts/qcom/msm8998-sony-xperia-yoshino-lilac.dts
new file mode 100644
index 000000000000..caacb7c28402
--- /dev/null
+++ b/arch/arm64/boot/dts/qcom/msm8998-sony-xperia-yoshino-lilac.dts
@@ -0,0 +1,31 @@
+// SPDX-License-Identifier: BSD-3-Clause
+/*
+ * Copyright (c) 2021, AngeloGioacchino Del Regno
+ *                     <angelogioacchino.delregno@somainline.org>
+ */
+
+/dts-v1/;
+
+#include "msm8998-sony-xperia-yoshino.dtsi"
+
+/ {
+	model = "Sony Xperia XZ1 Compact";
+	compatible = "sony,xperia-lilac", "qcom,msm8998";
+	chassis-type = "handset";
+};
+
+&ibb {
+	regulator-min-microvolt = <5500000>;
+	regulator-max-microvolt = <5500000>;
+};
+
+&lab {
+	regulator-min-microvolt = <5500000>;
+	regulator-max-microvolt = <5500000>;
+	qcom,soft-start-us = <800>;
+};
+
+&vreg_l22a_2p85 {
+	regulator-min-microvolt = <2800000>;
+	regulator-max-microvolt = <2800000>;
+};
diff --git a/arch/arm64/boot/dts/qcom/msm8998-sony-xperia-yoshino-maple.dts b/arch/arm64/boot/dts/qcom/msm8998-sony-xperia-yoshino-maple.dts
new file mode 100644
index 000000000000..978495a8a6b9
--- /dev/null
+++ b/arch/arm64/boot/dts/qcom/msm8998-sony-xperia-yoshino-maple.dts
@@ -0,0 +1,55 @@
+// SPDX-License-Identifier: BSD-3-Clause
+/*
+ * Copyright (c) 2021, AngeloGioacchino Del Regno
+ *                     <angelogioacchino.delregno@somainline.org>
+ */
+
+/dts-v1/;
+
+#include "msm8998-sony-xperia-yoshino.dtsi"
+
+/ {
+	model = "Sony Xperia XZ Premium";
+	compatible = "sony,xperia-maple", "qcom,msm8998";
+	chassis-type = "handset";
+
+	disp_dvdd_vreg: disp-dvdd-vreg {
+		compatible = "regulator-fixed";
+		regulator-name = "disp_dvdd_en";
+		regulator-min-microvolt = <1350000>;
+		regulator-max-microvolt = <1350000>;
+		startup-delay-us = <0>;
+		enable-active-high;
+		gpio = <&pmi8998_gpio 10 GPIO_ACTIVE_HIGH>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&disp_dvdd_en>;
+	};
+};
+
+&ibb {
+	regulator-min-microvolt = <5600000>;
+	regulator-max-microvolt = <5600000>;
+};
+
+&lab {
+	regulator-min-microvolt = <5800000>;
+	regulator-max-microvolt = <5800000>;
+	qcom,soft-start-us = <200>;
+};
+
+&pmi8998_gpio {
+	disp_dvdd_en: disp-dvdd-en-active {
+		pins = "gpio10";
+		function = "normal";
+		bias-disable;
+		drive-push-pull;
+		output-high;
+		power-source = <0>;
+		qcom,drive-strength = <1>;
+	};
+};
+
+&vreg_l22a_2p85 {
+	regulator-min-microvolt = <2704000>;
+	regulator-max-microvolt = <2704000>;
+};
diff --git a/arch/arm64/boot/dts/qcom/msm8998-sony-xperia-yoshino-poplar.dts b/arch/arm64/boot/dts/qcom/msm8998-sony-xperia-yoshino-poplar.dts
new file mode 100644
index 000000000000..4a1f98a21031
--- /dev/null
+++ b/arch/arm64/boot/dts/qcom/msm8998-sony-xperia-yoshino-poplar.dts
@@ -0,0 +1,36 @@
+// SPDX-License-Identifier: BSD-3-Clause
+/*
+ * Copyright (c) 2021, AngeloGioacchino Del Regno
+ *                     <angelogioacchino.delregno@somainline.org>
+ */
+
+/dts-v1/;
+
+#include "msm8998-sony-xperia-yoshino.dtsi"
+
+/ {
+	model = "Sony Xperia XZ1";
+	compatible = "sony,xperia-poplar", "qcom,msm8998";
+	chassis-type = "handset";
+};
+
+&ibb {
+	regulator-min-microvolt = <5600000>;
+	regulator-max-microvolt = <5600000>;
+};
+
+&lab {
+	regulator-min-microvolt = <5600000>;
+	regulator-max-microvolt = <5600000>;
+	qcom,soft-start-us = <800>;
+};
+
+&vreg_l18a_2p85 {
+	regulator-min-microvolt = <2850000>;
+	regulator-max-microvolt = <2850000>;
+};
+
+&vreg_l22a_2p85 {
+	regulator-min-microvolt = <2700000>;
+	regulator-max-microvolt = <2700000>;
+};
diff --git a/arch/arm64/boot/dts/qcom/msm8998-sony-xperia-yoshino.dtsi b/arch/arm64/boot/dts/qcom/msm8998-sony-xperia-yoshino.dtsi
new file mode 100644
index 000000000000..91e391282181
--- /dev/null
+++ b/arch/arm64/boot/dts/qcom/msm8998-sony-xperia-yoshino.dtsi
@@ -0,0 +1,670 @@
+// SPDX-License-Identifier: BSD-3-Clause
+/*
+ * Copyright (c) 2021, AngeloGioacchino Del Regno
+ *                     <angelogioacchino.delregno@somainline.org>
+ * Copyright (c) 2021, Konrad Dybcio <konrad.dybcio@somainline.org>
+ */
+
+#include "msm8998.dtsi"
+#include "pm8005.dtsi"
+#include "pm8998.dtsi"
+#include "pmi8998.dtsi"
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/leds/common.h>
+#include <dt-bindings/pinctrl/qcom,pmic-gpio.h>
+#include <dt-bindings/sound/qcom,q6afe.h>
+#include <dt-bindings/sound/qcom,q6asm.h>
+
+/ {
+	/* required for bootloader to select correct board */
+	qcom,msm-id = <0x124 0x20000>, <0x124 0x20001>; /* 8998v2, v2.1 */
+	qcom,board-id = <8 0>;
+
+	clocks {
+		compatible = "simple-bus";
+
+		div1_mclk: divclk1 {
+			compatible = "gpio-gate-clock";
+			pinctrl-0 = <&audio_mclk_pin>;
+			pinctrl-names = "default";
+			clocks = <&rpmcc RPM_SMD_DIV_CLK1>;
+			#clock-cells = <0>;
+			enable-gpios = <&pm8998_gpio 13 GPIO_ACTIVE_HIGH>;
+		};
+	};
+
+	board_vbat: vbat-regulator {
+		compatible = "regulator-fixed";
+		regulator-name = "VBAT";
+
+		regulator-min-microvolt = <4000000>;
+		regulator-max-microvolt = <4000000>;
+		regulator-always-on;
+		regulator-boot-on;
+	};
+
+	cam0_vdig_vreg: cam0-vdig {
+		compatible = "regulator-fixed";
+		regulator-name = "cam0_vdig";
+		startup-delay-us = <0>;
+		enable-active-high;
+		gpio = <&tlmm 21 GPIO_ACTIVE_HIGH>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&cam0_vdig_default>;
+	};
+
+	cam1_vdig_vreg: cam1-vdig {
+		compatible = "regulator-fixed";
+		regulator-name = "cam1_vdig";
+		startup-delay-us = <0>;
+		enable-active-high;
+		gpio = <&tlmm 25 GPIO_ACTIVE_HIGH>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&cam1_vdig_default>;
+		vin-supply = <&vreg_s3a_1p35>;
+	};
+
+	cam_vio_vreg: cam-vio-vreg {
+		compatible = "regulator-fixed";
+		regulator-name = "cam_vio_vreg";
+		startup-delay-us = <0>;
+		enable-active-high;
+		gpio = <&pmi8998_gpio 1 GPIO_ACTIVE_HIGH>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&cam_vio_default>;
+		vin-supply = <&vreg_lvs1a_1p8>;
+	};
+
+	touch_vddio_vreg: touch-vddio-vreg {
+		compatible = "regulator-fixed";
+		regulator-name = "touch_vddio_vreg";
+		startup-delay-us = <10000>;
+		gpio = <&tlmm 133 GPIO_ACTIVE_HIGH>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&ts_vddio_en>;
+	};
+
+	vph_pwr: vph-pwr-regulator {
+		compatible = "regulator-fixed";
+		regulator-name = "vph_pwr";
+		regulator-always-on;
+		regulator-boot-on;
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+		input-name = "gpio-keys";
+		label = "Side buttons";
+		pinctrl-names = "default";
+		pinctrl-0 = <&vol_down_pin_a>, <&cam_focus_pin_a>,
+			    <&cam_snapshot_pin_a>;
+		vol-down {
+			label = "Volume Down";
+			gpios = <&pm8998_gpio 5 GPIO_ACTIVE_LOW>;
+			linux,input-type = <EV_KEY>;
+			linux,code = <KEY_VOLUMEDOWN>;
+			gpio-key,wakeup;
+			debounce-interval = <15>;
+		};
+
+		camera-snapshot {
+			label = "Camera Snapshot";
+			gpios = <&pm8998_gpio 7 GPIO_ACTIVE_LOW>;
+			linux,input-type = <EV_KEY>;
+			linux,code = <KEY_CAMERA>;
+			debounce-interval = <15>;
+		};
+
+		camera-focus {
+			label = "Camera Focus";
+			gpios = <&pm8998_gpio 8 GPIO_ACTIVE_LOW>;
+			linux,input-type = <EV_KEY>;
+			linux,code = <KEY_CAMERA_FOCUS>;
+			debounce-interval = <15>;
+		};
+	};
+
+	gpio-hall-sensor {
+		compatible = "gpio-keys";
+		input-name = "hall-sensors";
+		label = "Hall sensors";
+		pinctrl-names = "default";
+		pinctrl-0 = <&hall_sensor0_default>;
+
+		hall-sensor0 {
+			label = "Cover Hall Sensor";
+			gpios = <&tlmm 124 GPIO_ACTIVE_LOW>;
+			linux,input-type = <EV_SW>;
+			linux,code = <SW_LID>;
+			gpio-key,wakeup;
+			debounce-interval = <30>;
+		};
+	};
+
+	reserved-memory {
+		#address-cells = <2>;
+		#size-cells = <2>;
+		ranges;
+
+		hyp_mem: memory@85800000 {
+			reg = <0x0 0x85800000 0x0 0x3700000>;
+			no-map;
+		};
+
+		cont_splash_mem: memory@9d400000 {
+			reg = <0x0 0x9d400000 0x0 0x2400000>;
+			no-map;
+		};
+
+		zap_shader_region: memory@f6400000 {
+			compatible = "shared-dma-pool";
+			reg = <0x0 0xf6400000 0x0 0x2000>;
+			no-map;
+		};
+
+		adsp_region: memory@fe000000 {
+			reg = <0x0 0xfe000000 0x0 0x800000>;
+			no-map;
+		};
+
+		qseecom_region: memory@fe800000 {
+			reg = <0x0 0xfe800000 0x0 0x1400000>;
+			no-map;
+		};
+
+		ramoops@ffc00000 {
+			compatible = "ramoops";
+			reg = <0x0 0xffc00000 0x0 0x100000>;
+			record-size = <0x10000>;
+			console-size = <0x60000>;
+			ftrace-size = <0x10000>;
+			pmsg-size = <0x20000>;
+			ecc-size = <16>;
+		};
+	};
+
+	vibrator {
+		compatible = "gpio-vibrator";
+		enable-gpios = <&pmi8998_gpio 5 GPIO_ACTIVE_HIGH>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&vib_default>;
+	};
+};
+
+&blsp1_i2c5 {
+	status = "okay";
+	clock-frequency = <355000>;
+
+	touchscreen@2c {
+		compatible = "syna,rmi4-i2c";
+		reg = <0x2c>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		interrupts-extended = <&tlmm 125 IRQ_TYPE_EDGE_FALLING>;
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&ts_int_n>;
+
+		vdd-supply = <&vreg_l28_3p0>;
+		vio-supply = <&touch_vddio_vreg>;
+
+		syna,reset-delay-ms = <220>;
+		syna,startup-delay-ms = <1000>;
+
+		rmi4-f01@1 {
+			reg = <0x01>;
+			syna,nosleep-mode = <1>;
+		};
+
+		rmi4-f11@11 {
+			reg = <0x11>;
+			syna,sensor-type = <1>;
+		};
+	};
+};
+
+&blsp1_i2c5_sleep {
+	bias-disable;
+};
+
+&blsp1_uart3 {
+	status = "okay";
+
+	bluetooth {
+		compatible = "qcom,wcn3990-bt";
+
+		vddio-supply = <&vreg_s4a_1p8>;
+		vddxo-supply = <&vreg_l7a_1p8>;
+		vddrf-supply = <&vreg_l17a_1p3>;
+		vddch0-supply = <&vreg_l25a_3p3>;
+		max-speed = <3200000>;
+
+		clocks = <&rpmcc RPM_SMD_RF_CLK2_PIN>;
+	};
+};
+
+&blsp2_uart1 {
+	status = "okay";
+};
+
+&ibb {
+	regulator-min-microamp = <800000>;
+	regulator-max-microamp = <800000>;
+	regulator-enable-ramp-delay = <200>;
+	regulator-over-current-protection;
+	regulator-pull-down;
+	regulator-ramp-delay = <1>;
+	regulator-settling-time-up-us = <600>;
+	regulator-settling-time-down-us = <1000>;
+	regulator-soft-start;
+	qcom,discharge-resistor-kohms = <300>;
+};
+
+&lab {
+	regulator-min-microamp = <200000>;
+	regulator-max-microamp = <200000>;
+	regulator-enable-ramp-delay = <500>;
+	regulator-over-current-protection;
+	regulator-pull-down;
+	regulator-ramp-delay = <1>;
+	regulator-settling-time-up-us = <50000>;
+	regulator-settling-time-down-us = <3000>;
+	regulator-soft-start;
+};
+
+&mmcc {
+	status = "ok";
+};
+
+&mmss_smmu {
+	status = "ok";
+};
+
+&pm8005_lsid1 {
+	pm8005-regulators {
+		compatible = "qcom,pm8005-regulators";
+
+		vdd_s1-supply = <&vph_pwr>;
+
+		/* VDD_GFX supply */
+		pm8005_s1: s1 {
+			regulator-min-microvolt = <524000>;
+			regulator-max-microvolt = <1088000>;
+			regulator-enable-ramp-delay = <500>;
+			regulator-always-on;
+		};
+	};
+};
+
+&pm8998_gpio {
+	vol_down_pin_a: vol-down-active {
+		pins = "gpio5";
+		function = PMIC_GPIO_FUNC_NORMAL;
+		bias-pull-up;
+		input-enable;
+		qcom,drive-strength = <PMIC_GPIO_STRENGTH_NO>;
+	};
+
+	cam_focus_pin_a: cam-focus-btn-active {
+		pins = "gpio7";
+		function = PMIC_GPIO_FUNC_NORMAL;
+		bias-pull-up;
+		input-enable;
+		qcom,drive-strength = <PMIC_GPIO_STRENGTH_NO>;
+	};
+
+	cam_snapshot_pin_a: cam-snapshot-btn-active {
+		pins = "gpio8";
+		function = PMIC_GPIO_FUNC_NORMAL;
+		bias-pull-up;
+		input-enable;
+		qcom,drive-strength = <PMIC_GPIO_STRENGTH_NO>;
+	};
+
+	audio_mclk_pin: audio-mclk-pin-active {
+		pins = "gpio13";
+		function = "func2";
+		power-source = <0>;
+	};
+};
+
+&pmi8998_gpio {
+	cam_vio_default: cam-vio-active {
+		pins = "gpio1";
+		function = PMIC_GPIO_FUNC_NORMAL;
+		bias-disable;
+		drive-push-pull;
+		output-low;
+		qcom,drive-strength = <PMIC_GPIO_STRENGTH_HIGH>;
+		power-source = <1>;
+	};
+
+	vib_default: vib-en {
+		pins = "gpio5";
+		function = PMIC_GPIO_FUNC_NORMAL;
+		bias-disable;
+		drive-push-pull;
+		output-low;
+		qcom,drive-strength = <PMIC_GPIO_STRENGTH_NO>;
+		power-source = <0>;
+	};
+};
+
+&pm8998_pon {
+	resin {
+		compatible = "qcom,pm8941-resin";
+		interrupts = <GIC_SPI 0x8 1 IRQ_TYPE_EDGE_BOTH>;
+		debounce = <15625>;
+		bias-pull-up;
+		linux,code = <KEY_VOLUMEUP>;
+	};
+};
+
+&qusb2phy {
+	status = "okay";
+
+	vdda-pll-supply = <&vreg_l12a_1p8>;
+	vdda-phy-dpdm-supply = <&vreg_l24a_3p075>;
+};
+
+&rpm_requests {
+	pm8998-regulators {
+		compatible = "qcom,rpm-pm8998-regulators";
+
+		vdd_s1-supply = <&vph_pwr>;
+		vdd_s2-supply = <&vph_pwr>;
+		vdd_s3-supply = <&vph_pwr>;
+		vdd_s4-supply = <&vph_pwr>;
+		vdd_s5-supply = <&vph_pwr>;
+		vdd_s6-supply = <&vph_pwr>;
+		vdd_s7-supply = <&vph_pwr>;
+		vdd_s8-supply = <&vph_pwr>;
+		vdd_s9-supply = <&vph_pwr>;
+		vdd_s10-supply = <&vph_pwr>;
+		vdd_s11-supply = <&vph_pwr>;
+		vdd_s12-supply = <&vph_pwr>;
+		vdd_s13-supply = <&vph_pwr>;
+		vdd_l1_l27-supply = <&vreg_s7a_1p025>;
+		vdd_l2_l8_l17-supply = <&vreg_s3a_1p35>;
+		vdd_l3_l11-supply = <&vreg_s7a_1p025>;
+		vdd_l4_l5-supply = <&vreg_s7a_1p025>;
+		vdd_l6-supply = <&vreg_s5a_2p04>;
+		vdd_l7_l12_l14_l15-supply = <&vreg_s5a_2p04>;
+		vdd_l9-supply = <&vreg_bob>;
+		vdd_l10_l23_l25-supply = <&vreg_bob>;
+		vdd_l13_l19_l21-supply = <&vreg_bob>;
+		vdd_l16_l28-supply = <&vreg_bob>;
+		vdd_l18_l22-supply = <&vreg_bob>;
+		vdd_l20_l24-supply = <&vreg_bob>;
+		vdd_l26-supply = <&vreg_s3a_1p35>;
+		vdd_lvs1_lvs2-supply = <&vreg_s4a_1p8>;
+
+		vreg_s3a_1p35: s3 {
+			regulator-min-microvolt = <1352000>;
+			regulator-max-microvolt = <1352000>;
+		};
+		vreg_s4a_1p8: s4 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			regulator-system-load = <100000>;
+			regulator-allow-set-load;
+		};
+		vreg_s5a_2p04: s5 {
+			regulator-min-microvolt = <1904000>;
+			regulator-max-microvolt = <2032000>;
+		};
+		vreg_s7a_1p025: s7 {
+			regulator-min-microvolt = <900000>;
+			regulator-max-microvolt = <1028000>;
+		};
+		vreg_l1a_0p875: l1 {
+			regulator-min-microvolt = <880000>;
+			regulator-max-microvolt = <880000>;
+			regulator-system-load = <73400>;
+			regulator-allow-set-load;
+		};
+		vreg_l2a_1p2: l2 {
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1200000>;
+			regulator-system-load = <12560>;
+			regulator-allow-set-load;
+		};
+		vreg_l3a_1p0: l3 {
+			regulator-min-microvolt = <1000000>;
+			regulator-max-microvolt = <1000000>;
+		};
+		vreg_l5a_0p8: l5 {
+			regulator-min-microvolt = <800000>;
+			regulator-max-microvolt = <800000>;
+		};
+		vreg_l6a_1p8: l6 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+		};
+		vreg_l7a_1p8: l7 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+		};
+		vreg_l8a_1p2: l8 {
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1200000>;
+		};
+		vreg_l9a_1p8: l9 {
+			regulator-min-microvolt = <1808000>;
+			regulator-max-microvolt = <2960000>;
+		};
+		vreg_l10a_1p8: l10 {
+			regulator-min-microvolt = <1808000>;
+			regulator-max-microvolt = <2960000>;
+		};
+		vreg_l11a_1p0: l11 {
+			regulator-min-microvolt = <1000000>;
+			regulator-max-microvolt = <1000000>;
+		};
+		vreg_l12a_1p8: l12 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+		};
+		vreg_l13a_2p95: l13 {
+			regulator-min-microvolt = <1808000>;
+			regulator-max-microvolt = <2960000>;
+			regulator-allow-set-load;
+		};
+		vreg_l14a_1p85: l14 {
+			regulator-min-microvolt = <1848000>;
+			regulator-max-microvolt = <1856000>;
+			regulator-system-load = <32000>;
+			regulator-allow-set-load;
+		};
+		vreg_l15a_1p8: l15 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+		};
+		vreg_l16a_2p7: l16 {
+			regulator-min-microvolt = <2704000>;
+			regulator-max-microvolt = <2704000>;
+		};
+		vreg_l17a_1p3: l17 {
+			regulator-min-microvolt = <1304000>;
+			regulator-max-microvolt = <1304000>;
+		};
+		vreg_l18a_2p85: l18 {};
+		vreg_l19a_2p7: l19 {
+			regulator-min-microvolt = <2696000>;
+			regulator-max-microvolt = <2704000>;
+		};
+		vreg_l20a_2p95: l20 {
+			regulator-min-microvolt = <2960000>;
+			regulator-max-microvolt = <2960000>;
+			regulator-system-load = <10000>;
+			regulator-allow-set-load;
+		};
+		vreg_l21a_2p95: l21 {
+			regulator-min-microvolt = <2960000>;
+			regulator-max-microvolt = <2960000>;
+			regulator-system-load = <800000>;
+			regulator-allow-set-load;
+		};
+		vreg_l22a_2p85: l22 { };
+		vreg_l23a_3p3: l23 {
+			regulator-min-microvolt = <3312000>;
+			regulator-max-microvolt = <3312000>;
+		};
+		vreg_l24a_3p075: l24 {
+			regulator-min-microvolt = <3088000>;
+			regulator-max-microvolt = <3088000>;
+		};
+		vreg_l25a_3p3: l25 {
+			regulator-min-microvolt = <3104000>;
+			regulator-max-microvolt = <3312000>;
+		};
+		vreg_l26a_1p2: l26 {
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1200000>;
+			regulator-allow-set-load;
+		};
+		vreg_l28_3p0: l28 {
+			regulator-min-microvolt = <3000000>;
+			regulator-max-microvolt = <3000000>;
+		};
+		vreg_lvs1a_1p8: lvs1 { };
+		vreg_lvs2a_1p8: lvs2 { };
+	};
+
+	pmi8998-regulators {
+		compatible = "qcom,rpm-pmi8998-regulators";
+
+		vdd_bob-supply = <&vph_pwr>;
+
+		vreg_bob: bob {
+			regulator-min-microvolt = <3312000>;
+			regulator-max-microvolt = <3600000>;
+		};
+	};
+};
+
+&sdhc2 {
+	status = "okay";
+	cd-gpios = <&tlmm 95 GPIO_ACTIVE_HIGH>;
+
+	vmmc-supply = <&vreg_l21a_2p95>;
+	vqmmc-supply = <&vreg_l13a_2p95>;
+
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&sdc2_clk_on  &sdc2_cmd_on  &sdc2_data_on  &sdc2_cd_on>;
+	pinctrl-1 = <&sdc2_clk_off &sdc2_cmd_off &sdc2_data_off &sdc2_cd_off>;
+};
+
+&tlmm {
+	gpio-reserved-ranges = <0 4>, <81 4>;
+
+	mdp_vsync_n: mdp-vsync-n {
+		pins = "gpio10";
+		function = "mdp_vsync_a";
+		drive-strength = <2>;
+		bias-pull-down;
+	};
+
+	nfc_ven: nfc-ven {
+		pins = "gpio12";
+		function = "gpio";
+		bias-disable;
+		drive-strength = <2>;
+		output-low;
+	};
+
+	msm_mclk0_default: msm-mclk0-active {
+		pins = "gpio13";
+		function = "cam_mclk";
+		drive-strength = <2>;
+		bias-disable;
+	};
+
+	msm_mclk1_default: msm-mclk1-active {
+		pins = "gpio14";
+		function = "cam_mclk";
+		drive-strength = <2>;
+		bias-disable;
+	};
+
+	cci0_default: cci0-default {
+		pins = "gpio18", "gpio19";
+		function = "cci_i2c";
+		bias-disable;
+		drive-strength = <2>;
+	};
+
+	cci1_default: cci1-default {
+		pins = "gpio19", "gpio20";
+		function = "cci_i2c";
+		bias-disable;
+		drive-strength = <2>;
+	};
+
+	cam0_vdig_default: cam0-vdig-default {
+		pins = "gpio21";
+		function = "gpio";
+		bias-disable;
+		drive-strength = <2>;
+	};
+
+	cam1_vdig_default: cam1-vdig-default {
+		pins = "gpio25";
+		function = "gpio";
+		bias-disable;
+		drive-strength = <2>;
+	};
+
+	hall_sensor0_default: acc-cover-open {
+		pins = "gpio124";
+		function = "gpio";
+		bias-disable;
+		drive-strength = <2>;
+		input-enable;
+	};
+
+	ts_int_n: ts-int-n {
+		pins = "gpio125";
+		function = "gpio";
+		drive-strength = <8>;
+		bias-pull-up;
+	};
+
+	ts_vddio_en: ts-vddio-en-default {
+		pins = "gpio133";
+		function = "gpio";
+		bias-disable;
+		drive-strength = <2>;
+		output-low;
+	};
+};
+
+/*
+ * WARNING:
+ * Disable UFS until card quirks are in to avoid unrecoverable hard-brick
+ * that would happen as soon as the UFS card gets probed as, without the
+ * required quirks, the bootloader will be erased right after card probe.
+ */
+&ufshc {
+	status = "disabled";
+};
+
+&ufsphy {
+	status = "disabled";
+};
+
+&usb3 {
+	status = "okay";
+};
+
+&usb3_dwc3 {
+	/* Force to peripheral until we have Type-C hooked up */
+	dr_mode = "peripheral";
+};
+
+&usb3phy {
+	status = "okay";
+
+	vdda-phy-supply = <&vreg_l1a_0p875>;
+	vdda-pll-supply = <&vreg_l2a_1p2>;
+};
diff --git a/arch/arm64/boot/dts/qcom/msm8998.dtsi b/arch/arm64/boot/dts/qcom/msm8998.dtsi
index 34039b5c8017..408f265e277b 100644
--- a/arch/arm64/boot/dts/qcom/msm8998.dtsi
+++ b/arch/arm64/boot/dts/qcom/msm8998.dtsi
@@ -4,6 +4,7 @@
 #include <dt-bindings/interrupt-controller/arm-gic.h>
 #include <dt-bindings/clock/qcom,gcc-msm8998.h>
 #include <dt-bindings/clock/qcom,gpucc-msm8998.h>
+#include <dt-bindings/clock/qcom,mmcc-msm8998.h>
 #include <dt-bindings/clock/qcom,rpmcc.h>
 #include <dt-bindings/power/qcom-rpmpd.h>
 #include <dt-bindings/gpio/gpio.h>
@@ -117,7 +118,7 @@
 			clock-output-names = "xo_board";
 		};
 
-		sleep_clk {
+		sleep_clk: sleep-clk {
 			compatible = "fixed-clock";
 			#clock-cells = <0>;
 			clock-frequency = <32764>;
@@ -308,38 +309,42 @@
 			LITTLE_CPU_SLEEP_0: cpu-sleep-0-0 {
 				compatible = "arm,idle-state";
 				idle-state-name = "little-retention";
+				/* CPU Retention (C2D), L2 Active */
 				arm,psci-suspend-param = <0x00000002>;
 				entry-latency-us = <81>;
 				exit-latency-us = <86>;
-				min-residency-us = <200>;
+				min-residency-us = <504>;
 			};
 
 			LITTLE_CPU_SLEEP_1: cpu-sleep-0-1 {
 				compatible = "arm,idle-state";
 				idle-state-name = "little-power-collapse";
+				/* CPU + L2 Power Collapse (C3, D4) */
 				arm,psci-suspend-param = <0x40000003>;
-				entry-latency-us = <273>;
-				exit-latency-us = <612>;
-				min-residency-us = <1000>;
+				entry-latency-us = <814>;
+				exit-latency-us = <4562>;
+				min-residency-us = <9183>;
 				local-timer-stop;
 			};
 
 			BIG_CPU_SLEEP_0: cpu-sleep-1-0 {
 				compatible = "arm,idle-state";
 				idle-state-name = "big-retention";
+				/* CPU Retention (C2D), L2 Active */
 				arm,psci-suspend-param = <0x00000002>;
 				entry-latency-us = <79>;
 				exit-latency-us = <82>;
-				min-residency-us = <200>;
+				min-residency-us = <1302>;
 			};
 
 			BIG_CPU_SLEEP_1: cpu-sleep-1-1 {
 				compatible = "arm,idle-state";
 				idle-state-name = "big-power-collapse";
+				/* CPU + L2 Power Collapse (C3, D4) */
 				arm,psci-suspend-param = <0x40000003>;
-				entry-latency-us = <336>;
-				exit-latency-us = <525>;
-				min-residency-us = <1000>;
+				entry-latency-us = <724>;
+				exit-latency-us = <2027>;
+				min-residency-us = <9419>;
 				local-timer-stop;
 			};
 		};
@@ -855,21 +860,24 @@
 			#reset-cells = <1>;
 			#power-domain-cells = <1>;
 			reg = <0x00100000 0xb0000>;
+
+			clock-names = "xo", "sleep_clk";
+			clocks = <&xo>, <&sleep_clk>;
 		};
 
-		rpm_msg_ram: memory@778000 {
+		rpm_msg_ram: sram@778000 {
 			compatible = "qcom,rpm-msg-ram";
 			reg = <0x00778000 0x7000>;
 		};
 
-		qfprom: qfprom@780000 {
+		qfprom: qfprom@784000 {
 			compatible = "qcom,qfprom";
-			reg = <0x00780000 0x621c>;
+			reg = <0x00784000 0x621c>;
 			#address-cells = <1>;
 			#size-cells = <1>;
 
-			qusb2_hstx_trim: hstx-trim@423a {
-				reg = <0x423a 0x1>;
+			qusb2_hstx_trim: hstx-trim@23a {
+				reg = <0x23a 0x1>;
 				bits = <0 4>;
 			};
 		};
@@ -954,10 +962,10 @@
 			interrupts = <GIC_SPI 405 IRQ_TYPE_LEVEL_HIGH>;
 			interrupt-names = "msi";
 			interrupt-map-mask = <0 0 0 0x7>;
-			interrupt-map =	<0 0 0 1 &intc 0 135 IRQ_TYPE_LEVEL_HIGH>,
-					<0 0 0 2 &intc 0 136 IRQ_TYPE_LEVEL_HIGH>,
-					<0 0 0 3 &intc 0 138 IRQ_TYPE_LEVEL_HIGH>,
-					<0 0 0 4 &intc 0 139 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-map =	<0 0 0 1 &intc 0 0 135 IRQ_TYPE_LEVEL_HIGH>,
+					<0 0 0 2 &intc 0 0 136 IRQ_TYPE_LEVEL_HIGH>,
+					<0 0 0 3 &intc 0 0 138 IRQ_TYPE_LEVEL_HIGH>,
+					<0 0 0 4 &intc 0 0 139 IRQ_TYPE_LEVEL_HIGH>;
 
 			clocks = <&gcc GCC_PCIE_0_PIPE_CLK>,
 				 <&gcc GCC_PCIE_0_MSTR_AXI_CLK>,
@@ -990,7 +998,7 @@
 			vdda-phy-supply = <&vreg_l1a_0p875>;
 			vdda-pll-supply = <&vreg_l2a_1p2>;
 
-			pciephy: lane@1c06800 {
+			pciephy: phy@1c06800 {
 				reg = <0x01c06200 0x128>, <0x01c06400 0x1fc>, <0x01c06800 0x20c>;
 				#phy-cells = <0>;
 
@@ -1062,7 +1070,7 @@
 			reset-names = "ufsphy";
 			resets = <&ufshc 0>;
 
-			ufsphy_lanes: lanes@1da7400 {
+			ufsphy_lanes: phy@1da7400 {
 				reg = <0x01da7400 0x128>,
 				      <0x01da7600 0x1fc>,
 				      <0x01da7c00 0x1dc>,
@@ -1416,6 +1424,103 @@
 			};
 		};
 
+		adreno_gpu: gpu@5000000 {
+			compatible = "qcom,adreno-540.1", "qcom,adreno";
+			reg = <0x05000000 0x40000>;
+			reg-names = "kgsl_3d0_reg_memory";
+
+			clocks = <&gcc GCC_GPU_CFG_AHB_CLK>,
+				<&gpucc RBBMTIMER_CLK>,
+				<&gcc GCC_BIMC_GFX_CLK>,
+				<&gcc GCC_GPU_BIMC_GFX_CLK>,
+				<&gpucc RBCPR_CLK>,
+				<&gpucc GFX3D_CLK>;
+			clock-names = "iface",
+				"rbbmtimer",
+				"mem",
+				"mem_iface",
+				"rbcpr",
+				"core";
+
+			interrupts = <0 300 IRQ_TYPE_LEVEL_HIGH>;
+			iommus = <&adreno_smmu 0>;
+			operating-points-v2 = <&gpu_opp_table>;
+			power-domains = <&rpmpd MSM8998_VDDMX>;
+			#stream-id-cells = <16>;
+			status = "disabled";
+
+			gpu_opp_table: opp-table {
+				compatible  = "operating-points-v2";
+				opp-710000097 {
+					opp-hz = /bits/ 64 <710000097>;
+					opp-level = <RPM_SMD_LEVEL_TURBO>;
+					opp-supported-hw = <0xFF>;
+				};
+
+				opp-670000048 {
+					opp-hz = /bits/ 64 <670000048>;
+					opp-level = <RPM_SMD_LEVEL_NOM_PLUS>;
+					opp-supported-hw = <0xFF>;
+				};
+
+				opp-596000097 {
+					opp-hz = /bits/ 64 <596000097>;
+					opp-level = <RPM_SMD_LEVEL_NOM>;
+					opp-supported-hw = <0xFF>;
+				};
+
+				opp-515000097 {
+					opp-hz = /bits/ 64 <515000097>;
+					opp-level = <RPM_SMD_LEVEL_SVS_PLUS>;
+					opp-supported-hw = <0xFF>;
+				};
+
+				opp-414000000 {
+					opp-hz = /bits/ 64 <414000000>;
+					opp-level = <RPM_SMD_LEVEL_SVS>;
+					opp-supported-hw = <0xFF>;
+				};
+
+				opp-342000000 {
+					opp-hz = /bits/ 64 <342000000>;
+					opp-level = <RPM_SMD_LEVEL_LOW_SVS>;
+					opp-supported-hw = <0xFF>;
+				};
+
+				opp-257000000 {
+					opp-hz = /bits/ 64 <257000000>;
+					opp-level = <RPM_SMD_LEVEL_MIN_SVS>;
+					opp-supported-hw = <0xFF>;
+				};
+			};
+		};
+
+		adreno_smmu: iommu@5040000 {
+			compatible = "qcom,msm8998-smmu-v2", "qcom,smmu-v2";
+			reg = <0x05040000 0x10000>;
+			clocks = <&gcc GCC_GPU_CFG_AHB_CLK>,
+				 <&gcc GCC_BIMC_GFX_CLK>,
+				 <&gcc GCC_GPU_BIMC_GFX_CLK>;
+			clock-names = "iface", "mem", "mem_iface";
+
+			#global-interrupts = <0>;
+			#iommu-cells = <1>;
+			interrupts =
+				<GIC_SPI 329 IRQ_TYPE_LEVEL_HIGH>,
+				<GIC_SPI 330 IRQ_TYPE_LEVEL_HIGH>,
+				<GIC_SPI 331 IRQ_TYPE_LEVEL_HIGH>;
+			/*
+			 * GPU-GX GDSC's parent is GPU-CX. We need to bring up the
+			 * GPU-CX for SMMU but we need both of them up for Adreno.
+			 * Contemporarily, we also need to manage the VDDMX rpmpd
+			 * domain in the Adreno driver.
+			 * Enable GPU CX/GX GDSCs here so that we can manage the
+			 * SoC VDDMX RPM Power Domain in the Adreno driver.
+			 */
+			power-domains = <&gpucc GPU_GX_GDSC>;
+			status = "disabled";
+		};
+
 		gpucc: clock-controller@5065000 {
 			compatible = "qcom,msm8998-gpucc";
 			#clock-cells = <1>;
@@ -1917,6 +2022,11 @@
 			};
 		};
 
+		sram@290000 {
+			compatible = "qcom,rpm-stats";
+			reg = <0x00290000 0x10000>;
+		};
+
 		spmi_bus: spmi@800f000 {
 			compatible = "qcom,spmi-pmic-arb";
 			reg =	<0x0800f000 0x1000>,
@@ -1981,7 +2091,6 @@
 			compatible = "qcom,msm8998-qmp-usb3-phy";
 			reg = <0x0c010000 0x18c>;
 			status = "disabled";
-			#clock-cells = <1>;
 			#address-cells = <1>;
 			#size-cells = <1>;
 			ranges;
@@ -1995,13 +2104,14 @@
 				 <&gcc GCC_USB3PHY_PHY_BCR>;
 			reset-names = "phy", "common";
 
-			usb1_ssphy: lane@c010200 {
+			usb1_ssphy: phy@c010200 {
 				reg = <0xc010200 0x128>,
 				      <0xc010400 0x200>,
 				      <0xc010c00 0x20c>,
 				      <0xc010600 0x128>,
 				      <0xc010800 0x200>;
 				#phy-cells = <0>;
+				#clock-cells = <1>;
 				clocks = <&gcc GCC_USB3_PHY_PIPE_CLK>;
 				clock-names = "pipe0";
 				clock-output-names = "usb3_phy_pipe_clk_src";
@@ -2187,7 +2297,7 @@
 			#size-cells = <0>;
 		};
 
-		blsp2_dma: dma@c184000 {
+		blsp2_dma: dma-controller@c184000 {
 			compatible = "qcom,bam-v1.7.0";
 			reg = <0x0c184000 0x25000>;
 			interrupts = <GIC_SPI 239 IRQ_TYPE_LEVEL_HIGH>;
@@ -2330,6 +2440,73 @@
 			#size-cells = <0>;
 		};
 
+		mmcc: clock-controller@c8c0000 {
+			compatible = "qcom,mmcc-msm8998";
+			#clock-cells = <1>;
+			#reset-cells = <1>;
+			#power-domain-cells = <1>;
+			reg = <0xc8c0000 0x40000>;
+			status = "disabled";
+
+			clock-names = "xo",
+				      "gpll0",
+				      "dsi0dsi",
+				      "dsi0byte",
+				      "dsi1dsi",
+				      "dsi1byte",
+				      "hdmipll",
+				      "dplink",
+				      "dpvco",
+				      "core_bi_pll_test_se";
+			clocks = <&rpmcc RPM_SMD_XO_CLK_SRC>,
+				 <&gcc GCC_MMSS_GPLL0_CLK>,
+				 <0>,
+				 <0>,
+				 <0>,
+				 <0>,
+				 <0>,
+				 <0>,
+				 <0>,
+				 <0>;
+		};
+
+		mmss_smmu: iommu@cd00000 {
+			compatible = "qcom,msm8998-smmu-v2", "qcom,smmu-v2";
+			reg = <0x0cd00000 0x40000>;
+			#iommu-cells = <1>;
+
+			clocks = <&mmcc MNOC_AHB_CLK>,
+				 <&mmcc BIMC_SMMU_AHB_CLK>,
+				 <&rpmcc RPM_SMD_MMAXI_CLK>,
+				 <&mmcc BIMC_SMMU_AXI_CLK>;
+			clock-names = "iface-mm", "iface-smmu",
+				      "bus-mm", "bus-smmu";
+			status = "disabled";
+
+			#global-interrupts = <0>;
+			interrupts =
+				<GIC_SPI 263 IRQ_TYPE_LEVEL_HIGH>,
+				<GIC_SPI 266 IRQ_TYPE_LEVEL_HIGH>,
+				<GIC_SPI 267 IRQ_TYPE_LEVEL_HIGH>,
+				<GIC_SPI 268 IRQ_TYPE_LEVEL_HIGH>,
+				<GIC_SPI 244 IRQ_TYPE_LEVEL_HIGH>,
+				<GIC_SPI 245 IRQ_TYPE_LEVEL_HIGH>,
+				<GIC_SPI 247 IRQ_TYPE_LEVEL_HIGH>,
+				<GIC_SPI 248 IRQ_TYPE_LEVEL_HIGH>,
+				<GIC_SPI 249 IRQ_TYPE_LEVEL_HIGH>,
+				<GIC_SPI 250 IRQ_TYPE_LEVEL_HIGH>,
+				<GIC_SPI 251 IRQ_TYPE_LEVEL_HIGH>,
+				<GIC_SPI 252 IRQ_TYPE_LEVEL_HIGH>,
+				<GIC_SPI 253 IRQ_TYPE_LEVEL_HIGH>,
+				<GIC_SPI 254 IRQ_TYPE_LEVEL_HIGH>,
+				<GIC_SPI 255 IRQ_TYPE_LEVEL_HIGH>,
+				<GIC_SPI 256 IRQ_TYPE_LEVEL_HIGH>,
+				<GIC_SPI 260 IRQ_TYPE_LEVEL_HIGH>,
+				<GIC_SPI 261 IRQ_TYPE_LEVEL_HIGH>,
+				<GIC_SPI 262 IRQ_TYPE_LEVEL_HIGH>,
+				<GIC_SPI 272 IRQ_TYPE_LEVEL_HIGH>;
+		};
+
 		remoteproc_adsp: remoteproc@17300000 {
 			compatible = "qcom,msm8998-adsp-pas";
 			reg = <0x17300000 0x4040>;
diff --git a/arch/arm64/boot/dts/qcom/pm6150l.dtsi b/arch/arm64/boot/dts/qcom/pm6150l.dtsi
index b49860cd1387..3ca2860bb0cf 100644
--- a/arch/arm64/boot/dts/qcom/pm6150l.dtsi
+++ b/arch/arm64/boot/dts/qcom/pm6150l.dtsi
@@ -1,6 +1,7 @@
 // SPDX-License-Identifier: BSD-3-Clause
 // Copyright (c) 2019, The Linux Foundation. All rights reserved.
 
+#include <dt-bindings/iio/qcom,spmi-vadc.h>
 #include <dt-bindings/interrupt-controller/irq.h>
 #include <dt-bindings/spmi/spmi.h>
 
diff --git a/arch/arm64/boot/dts/qcom/pm6350.dtsi b/arch/arm64/boot/dts/qcom/pm6350.dtsi
new file mode 100644
index 000000000000..c5d85064562b
--- /dev/null
+++ b/arch/arm64/boot/dts/qcom/pm6350.dtsi
@@ -0,0 +1,54 @@
+// SPDX-License-Identifier: BSD-3-Clause
+/*
+ * Copyright (c) 2021, Luca Weiss <luca@z3ntu.xyz>
+ */
+
+#include <dt-bindings/spmi/spmi.h>
+
+&spmi_bus {
+	pmic@0 {
+		compatible = "qcom,pm6350", "qcom,spmi-pmic";
+		reg = <0x0 SPMI_USID>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		pm6350_pon: pon@800 {
+			compatible = "qcom,pm8998-pon";
+			reg = <0x800>;
+			mode-bootloader = <0x2>;
+			mode-recovery = <0x1>;
+
+			pm6350_pwrkey: pwrkey {
+				compatible = "qcom,pm8941-pwrkey";
+				interrupts = <0x0 0x8 0x0 IRQ_TYPE_EDGE_BOTH>;
+				debounce = <15625>;
+				bias-pull-up;
+				linux,code = <KEY_POWER>;
+			};
+
+			pm6350_resin: resin {
+				compatible = "qcom,pm8941-resin";
+				interrupts = <0x0 0x8 0x1 IRQ_TYPE_EDGE_BOTH>;
+				debounce = <15625>;
+				bias-pull-up;
+				status = "disabled";
+			};
+		};
+
+		pm6350_gpios: gpios@c000 {
+			compatible = "qcom,pm6350-gpio";
+			reg = <0xc000>;
+			gpio-controller;
+			#gpio-cells = <2>;
+			interrupt-controller;
+			#interrupt-cells = <2>;
+		};
+	};
+
+	pmic@1 {
+		compatible = "qcom,pm6350", "qcom,spmi-pmic";
+		reg = <0x1 SPMI_USID>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+	};
+};
diff --git a/arch/arm64/boot/dts/qcom/pm660.dtsi b/arch/arm64/boot/dts/qcom/pm660.dtsi
index e847d7209afc..d0ef8a1675e2 100644
--- a/arch/arm64/boot/dts/qcom/pm660.dtsi
+++ b/arch/arm64/boot/dts/qcom/pm660.dtsi
@@ -49,9 +49,10 @@
 		};
 
 		pon: pon@800 {
-			compatible = "qcom,pm8916-pon";
-
+			compatible = "qcom,pm8998-pon";
 			reg = <0x800>;
+			mode-bootloader = <0x2>;
+			mode-recovery = <0x1>;
 
 			pwrkey {
 				compatible = "qcom,pm8941-pwrkey";
diff --git a/arch/arm64/boot/dts/qcom/pm660l.dtsi b/arch/arm64/boot/dts/qcom/pm660l.dtsi
index 05086cbe573b..cfef42353611 100644
--- a/arch/arm64/boot/dts/qcom/pm660l.dtsi
+++ b/arch/arm64/boot/dts/qcom/pm660l.dtsi
@@ -72,13 +72,6 @@
 			interrupt-names = "ovp";
 			label = "backlight";
 
-			qcom,switching-freq = <800>;
-			qcom,ovp-millivolt = <29600>;
-			qcom,current-boost-limit = <970>;
-			qcom,current-limit-microamp = <20000>;
-			qcom,num-strings = <2>;
-			qcom,enabled-strings = <0 1>;
-
 			status = "disabled";
 		};
 
diff --git a/arch/arm64/boot/dts/qcom/pm8916.dtsi b/arch/arm64/boot/dts/qcom/pm8916.dtsi
index f931cb0de231..d58902432812 100644
--- a/arch/arm64/boot/dts/qcom/pm8916.dtsi
+++ b/arch/arm64/boot/dts/qcom/pm8916.dtsi
@@ -41,6 +41,14 @@
 			};
 		};
 
+		pm8916_usbin: extcon@1300 {
+			compatible = "qcom,pm8941-misc";
+			reg = <0x1300>;
+			interrupts = <0x0 0x13 1 IRQ_TYPE_EDGE_BOTH>;
+			interrupt-names = "usb_vbus";
+			status = "disabled";
+		};
+
 		pm8916_temp: temp-alarm@2400 {
 			compatible = "qcom,spmi-temp-alarm";
 			reg = <0x2400>;
@@ -86,19 +94,17 @@
 		rtc@6000 {
 			compatible = "qcom,pm8941-rtc";
 			reg = <0x6000>;
-			reg-names = "rtc", "alarm";
 			interrupts = <0x0 0x61 0x1 IRQ_TYPE_EDGE_RISING>;
 		};
 
 		pm8916_mpps: mpps@a000 {
-			compatible = "qcom,pm8916-mpp";
+			compatible = "qcom,pm8916-mpp", "qcom,spmi-mpp";
 			reg = <0xa000>;
 			gpio-controller;
 			#gpio-cells = <2>;
-			interrupts = <0 0xa0 0 IRQ_TYPE_NONE>,
-				     <0 0xa1 0 IRQ_TYPE_NONE>,
-				     <0 0xa2 0 IRQ_TYPE_NONE>,
-				     <0 0xa3 0 IRQ_TYPE_NONE>;
+			gpio-ranges = <&pm8916_mpps 0 0 4>;
+			interrupt-controller;
+			#interrupt-cells = <2>;
 		};
 
 		pm8916_gpios: gpios@c000 {
diff --git a/arch/arm64/boot/dts/qcom/pm8994.dtsi b/arch/arm64/boot/dts/qcom/pm8994.dtsi
index ad19016df047..5ab46117d737 100644
--- a/arch/arm64/boot/dts/qcom/pm8994.dtsi
+++ b/arch/arm64/boot/dts/qcom/pm8994.dtsi
@@ -119,18 +119,13 @@
 		};
 
 		pm8994_mpps: mpps@a000 {
-			compatible = "qcom,pm8994-mpp";
+			compatible = "qcom,pm8994-mpp", "qcom,spmi-mpp";
 			reg = <0xa000>;
 			gpio-controller;
 			#gpio-cells = <2>;
-			interrupts = <0 0xa0 0 IRQ_TYPE_NONE>,
-				     <0 0xa1 0 IRQ_TYPE_NONE>,
-				     <0 0xa2 0 IRQ_TYPE_NONE>,
-				     <0 0xa3 0 IRQ_TYPE_NONE>,
-				     <0 0xa4 0 IRQ_TYPE_NONE>,
-				     <0 0xa5 0 IRQ_TYPE_NONE>,
-				     <0 0xa6 0 IRQ_TYPE_NONE>,
-				     <0 0xa7 0 IRQ_TYPE_NONE>;
+			gpio-ranges = <&pm8994_mpps 0 0 8>;
+			interrupt-controller;
+			#interrupt-cells = <2>;
 		};
 	};
 
diff --git a/arch/arm64/boot/dts/qcom/pmi8994.dtsi b/arch/arm64/boot/dts/qcom/pmi8994.dtsi
index b4ac900ab115..6e7c252568e6 100644
--- a/arch/arm64/boot/dts/qcom/pmi8994.dtsi
+++ b/arch/arm64/boot/dts/qcom/pmi8994.dtsi
@@ -38,11 +38,8 @@
 			reg = <0xd800 0xd900>;
 			interrupts = <3 0xd8 0x02 IRQ_TYPE_EDGE_RISING>;
 			interrupt-names = "short";
-			qcom,num-strings = <3>;
-			/* Yes, all four strings *have to* be defined or things won't work. */
-			qcom,enabled-strings = <0 1 2 3>;
 			qcom,cabc;
-			qcom,eternal-pfet;
+			qcom,external-pfet;
 			status = "disabled";
 		};
 	};
diff --git a/arch/arm64/boot/dts/qcom/pmi8998.dtsi b/arch/arm64/boot/dts/qcom/pmi8998.dtsi
index d230c510d4b7..0fef5f113f05 100644
--- a/arch/arm64/boot/dts/qcom/pmi8998.dtsi
+++ b/arch/arm64/boot/dts/qcom/pmi8998.dtsi
@@ -41,5 +41,17 @@
 				interrupt-names = "sc-err", "ocp";
 			};
 		};
+
+		pmi8998_wled: leds@d800 {
+			compatible = "qcom,pmi8998-wled";
+			reg = <0xd800 0xd900>;
+			interrupts = <0x3 0xd8 0x1 IRQ_TYPE_EDGE_RISING>,
+				     <0x3 0xd8 0x2 IRQ_TYPE_EDGE_RISING>;
+			interrupt-names = "ovp", "short";
+			label = "backlight";
+
+			status = "disabled";
+		};
+
 	};
 };
diff --git a/arch/arm64/boot/dts/qcom/pmk8350.dtsi b/arch/arm64/boot/dts/qcom/pmk8350.dtsi
index 04fc2632a0b2..769f9726806f 100644
--- a/arch/arm64/boot/dts/qcom/pmk8350.dtsi
+++ b/arch/arm64/boot/dts/qcom/pmk8350.dtsi
@@ -59,6 +59,7 @@
 			reg = <0x6100>, <0x6200>;
 			reg-names = "rtc", "alarm";
 			interrupts = <0x0 0x62 0x1 IRQ_TYPE_EDGE_RISING>;
+			status = "disabled";
 		};
 
 		pmk8350_gpios: gpio@b000 {
diff --git a/arch/arm64/boot/dts/qcom/qcs404.dtsi b/arch/arm64/boot/dts/qcom/qcs404.dtsi
index 339790ba585d..6db753b49326 100644
--- a/arch/arm64/boot/dts/qcom/qcs404.dtsi
+++ b/arch/arm64/boot/dts/qcom/qcs404.dtsi
@@ -318,7 +318,7 @@
 			status = "disabled";
 		};
 
-		rpm_msg_ram: memory@60000 {
+		rpm_msg_ram: sram@60000 {
 			compatible = "qcom,rpm-msg-ram";
 			reg = <0x00060000 0x6000>;
 		};
@@ -719,6 +719,11 @@
 			reg = <0x01937000 0x25000>;
 		};
 
+		sram@290000 {
+			compatible = "qcom,rpm-stats";
+			reg = <0x00290000 0x10000>;
+		};
+
 		spmi_bus: spmi@200f000 {
 			compatible = "qcom,spmi-pmic-arb";
 			reg = <0x0200f000 0x001000>,
diff --git a/arch/arm64/boot/dts/qcom/qrb5165-rb5.dts b/arch/arm64/boot/dts/qcom/qrb5165-rb5.dts
index 28d5b5528516..845eb7a6bf92 100644
--- a/arch/arm64/boot/dts/qcom/qrb5165-rb5.dts
+++ b/arch/arm64/boot/dts/qcom/qrb5165-rb5.dts
@@ -16,6 +16,8 @@
 / {
 	model = "Qualcomm Technologies, Inc. Robotics RB5";
 	compatible = "qcom,qrb5165-rb5", "qcom,sm8250";
+	qcom,msm-id = <455 0x20001>;
+	qcom,board-id = <11 3>;
 
 	aliases {
 		serial0 = &uart12;
@@ -1222,9 +1224,7 @@
 	status = "okay";
 
 	vdda-phy-supply = <&vreg_l5a_0p88>;
-	vdda-max-microamp = <89900>;
 	vdda-pll-supply = <&vreg_l9a_1p2>;
-	vdda-pll-max-microamp = <18800>;
 };
 
 &usb_1 {
diff --git a/arch/arm64/boot/dts/qcom/sa8155p-adp.dts b/arch/arm64/boot/dts/qcom/sa8155p-adp.dts
index 5ae2ddc65f7e..8756c2b25c7e 100644
--- a/arch/arm64/boot/dts/qcom/sa8155p-adp.dts
+++ b/arch/arm64/boot/dts/qcom/sa8155p-adp.dts
@@ -307,6 +307,16 @@
 	status = "okay";
 };
 
+&remoteproc_adsp {
+	status = "okay";
+	firmware-name = "qcom/sa8155p/adsp.mdt";
+};
+
+&remoteproc_cdsp {
+	status = "okay";
+	firmware-name = "qcom/sa8155p/cdsp.mdt";
+};
+
 &uart2 {
 	status = "okay";
 };
@@ -328,9 +338,7 @@
 	status = "okay";
 
 	vdda-phy-supply = <&vreg_l8c_1p2>;
-	vdda-max-microamp = <87100>;
 	vdda-pll-supply = <&vreg_l5a_0p88>;
-	vdda-pll-max-microamp = <18300>;
 };
 
 &usb_1 {
diff --git a/arch/arm64/boot/dts/qcom/sc7180-trogdor-coachz-r1.dts b/arch/arm64/boot/dts/qcom/sc7180-trogdor-coachz-r1.dts
index 21b516e0694a..8290d036044a 100644
--- a/arch/arm64/boot/dts/qcom/sc7180-trogdor-coachz-r1.dts
+++ b/arch/arm64/boot/dts/qcom/sc7180-trogdor-coachz-r1.dts
@@ -23,6 +23,20 @@
 	status = "disabled";
 };
 
+&pm6150_adc {
+	status = "disabled";
+
+	/delete-node/ skin-temp-thermistor@4e;
+	/delete-node/ charger-thermistor@4f;
+};
+
+&pm6150_adc_tm {
+	status = "disabled";
+
+	/delete-node/ charger-thermistor@0;
+	/delete-node/ skin-temp-thermistor@1;
+};
+
 /*
  * CoachZ rev1 is stuffed with a 47k NTC as thermistor for skin temperature,
  * which currently is not supported by the PM6150 ADC driver. Disable the
diff --git a/arch/arm64/boot/dts/qcom/sc7180-trogdor-coachz.dtsi b/arch/arm64/boot/dts/qcom/sc7180-trogdor-coachz.dtsi
index a758e4d22612..14ed09f30a73 100644
--- a/arch/arm64/boot/dts/qcom/sc7180-trogdor-coachz.dtsi
+++ b/arch/arm64/boot/dts/qcom/sc7180-trogdor-coachz.dtsi
@@ -11,6 +11,7 @@ ap_ec_spi: &spi6 {};
 ap_h1_spi: &spi0 {};
 
 #include "sc7180-trogdor.dtsi"
+#include "sc7180-trogdor-ti-sn65dsi86.dtsi"
 
 /* Deleted nodes from trogdor.dtsi */
 
@@ -33,7 +34,7 @@ ap_h1_spi: &spi0 {};
 			polling-delay = <0>;
 
 			thermal-sensors = <&pm6150_adc_tm 1>;
-			sustainable-power = <814>;
+			sustainable-power = <965>;
 
 			trips {
 				skin_temp_alert0: trip-point0 {
diff --git a/arch/arm64/boot/dts/qcom/sc7180-trogdor-homestar-r2.dts b/arch/arm64/boot/dts/qcom/sc7180-trogdor-homestar-r2.dts
new file mode 100644
index 000000000000..db6c2da67cea
--- /dev/null
+++ b/arch/arm64/boot/dts/qcom/sc7180-trogdor-homestar-r2.dts
@@ -0,0 +1,20 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Google Homestar board device tree source
+ *
+ * Copyright 2021 Google LLC.
+ */
+
+/dts-v1/;
+
+#include "sc7180-trogdor-homestar.dtsi"
+
+/ {
+	model = "Google Homestar (rev2)";
+	compatible = "google,homestar-rev2","google,homestar-rev23", "qcom,sc7180";
+};
+
+&panel {
+	/delete-property/hpd-gpios;
+	no-hpd;
+};
diff --git a/arch/arm64/boot/dts/qcom/sc7180-trogdor-homestar-r3.dts b/arch/arm64/boot/dts/qcom/sc7180-trogdor-homestar-r3.dts
new file mode 100644
index 000000000000..3fd8aa5bb7a6
--- /dev/null
+++ b/arch/arm64/boot/dts/qcom/sc7180-trogdor-homestar-r3.dts
@@ -0,0 +1,15 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Google Homestar board device tree source
+ *
+ * Copyright 2021 Google LLC.
+ */
+
+/dts-v1/;
+
+#include "sc7180-trogdor-homestar.dtsi"
+
+/ {
+	model = "Google Homestar (rev3+)";
+	compatible = "google,homestar", "qcom,sc7180";
+};
diff --git a/arch/arm64/boot/dts/qcom/sc7180-trogdor-homestar.dtsi b/arch/arm64/boot/dts/qcom/sc7180-trogdor-homestar.dtsi
new file mode 100644
index 000000000000..4ab890b2a1d4
--- /dev/null
+++ b/arch/arm64/boot/dts/qcom/sc7180-trogdor-homestar.dtsi
@@ -0,0 +1,336 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Google Homestar board device tree source
+ *
+ * Copyright 2021 Google LLC.
+ */
+
+#include "sc7180.dtsi"
+
+ap_ec_spi: &spi6 {};
+ap_h1_spi: &spi0 {};
+
+#include "sc7180-trogdor.dtsi"
+#include "sc7180-trogdor-ti-sn65dsi86.dtsi"
+
+/ {
+	/* BOARD-SPECIFIC TOP LEVEL NODES */
+
+	max98360a_1: max98360a_1 {
+		compatible = "maxim,max98360a";
+		#sound-dai-cells = <0>;
+	};
+
+	max98360a_2: max98360a_2 {
+		compatible = "maxim,max98360a";
+		#sound-dai-cells = <0>;
+	};
+
+	max98360a_3: max98360a_3 {
+		compatible = "maxim,max98360a";
+		#sound-dai-cells = <0>;
+	};
+
+	pp3300_touch: pp3300-touch {
+		compatible = "regulator-fixed";
+		regulator-name = "pp3300_touch";
+
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+
+		gpio = <&tlmm 87 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+		pinctrl-names = "default";
+		pinctrl-0 = <&en_pp3300_touch>;
+
+		vin-supply = <&pp3300_a>;
+	};
+
+	thermal-zones {
+		skin_temp_thermal: skin-temp-thermal {
+			polling-delay-passive = <250>;
+			polling-delay = <0>;
+
+			thermal-sensors = <&pm6150_adc_tm 1>;
+			sustainable-power = <965>;
+
+			trips {
+				skin_temp_alert0: trip-point0 {
+					temperature = <55000>;
+					hysteresis = <1000>;
+					type = "passive";
+				};
+
+				skin_temp_alert1: trip-point1 {
+					temperature = <58000>;
+					hysteresis = <1000>;
+					type = "passive";
+				};
+
+				skin-temp-crit {
+					temperature = <73000>;
+					hysteresis = <1000>;
+					type = "critical";
+				};
+			};
+
+			cooling-maps {
+				map0 {
+					trip = <&skin_temp_alert0>;
+					cooling-device = <&CPU6 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+							 <&CPU7 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
+				};
+
+				map1 {
+					trip = <&skin_temp_alert1>;
+					cooling-device = <&CPU6 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+							 <&CPU7 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
+				};
+			};
+		};
+	};
+};
+
+&ap_tp_i2c {
+	status = "disabled";
+};
+
+ap_ts_pen_1v8: &i2c4 {
+	status = "okay";
+	clock-frequency = <400000>;
+
+	ap_ts: touchscreen@14 {
+		compatible = "goodix,gt7375p";
+		reg = <0x14>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&ts_int_l>, <&ts_reset_l>;
+
+		interrupt-parent = <&tlmm>;
+		interrupts = <9 IRQ_TYPE_LEVEL_LOW>;
+
+		reset-gpios = <&tlmm 8 GPIO_ACTIVE_LOW>;
+
+		vdd-supply = <&pp3300_touch>;
+	};
+};
+
+/* Panel controls backlight over aux channel */
+
+&backlight {
+	status = "disabled";
+};
+
+&camcc {
+	status = "okay";
+};
+
+&panel {
+	compatible = "samsung,atna33xc20";
+	enable-gpios = <&tlmm 12 GPIO_ACTIVE_HIGH>;
+	/delete-property/ backlight;
+};
+
+&pm6150_adc {
+	skin-temp-thermistor@4d {
+		reg = <ADC5_AMUX_THM1_100K_PU>;
+		qcom,ratiometric;
+		qcom,hw-settle-time = <200>;
+	};
+};
+
+&pm6150_adc_tm {
+	status = "okay";
+
+	skin-temp-thermistor@1 {
+		reg = <1>;
+		io-channels = <&pm6150_adc ADC5_AMUX_THM1_100K_PU>;
+		qcom,ratiometric;
+		qcom,hw-settle-time-us = <200>;
+	};
+};
+
+&pp3300_dx_edp {
+	gpio = <&tlmm 67 GPIO_ACTIVE_HIGH>;
+};
+
+&secondary_mi2s {
+	qcom,playback-sd-lines = <0 1>;
+};
+
+&sound_multimedia1_codec {
+	sound-dai = <&max98360a>, <&max98360a_1>, <&max98360a_2>, <&max98360a_3> ;
+};
+
+&wifi {
+	qcom,ath10k-calibration-variant = "GO_HOMESTAR";
+};
+
+/* PINCTRL - modifications to sc7180-trogdor.dtsi */
+
+&en_pp3300_dx_edp {
+	pinmux {
+		pins = "gpio67";
+	};
+
+	pinconf {
+		pins = "gpio67";
+	};
+};
+
+&sec_mi2s_active{
+	pinmux {
+		pins = "gpio49", "gpio50", "gpio51", "gpio52";
+		function = "mi2s_1";
+	};
+};
+
+&ts_reset_l {
+	pinconf {
+		/*
+		 * We want reset state by default and it will be up to the
+		 * driver to disable this when it's ready.
+		 */
+		output-low;
+	};
+};
+
+/* PINCTRL - board-specific pinctrl */
+
+&tlmm {
+	gpio-line-names = "HUB_RST_L",
+			  "AP_RAM_ID0",
+			  "AP_SKU_ID2",
+			  "AP_RAM_ID1",
+			  "",
+			  "AP_RAM_ID2",
+			  "UF_CAM_EN",
+			  "WF_CAM_EN",
+			  "TS_RESET_L",
+			  "TS_INT_L",
+			  "",
+			  "EDP_BRIJ_IRQ",
+			  "AP_EDP_BKLTEN",
+			  "UF_CAM_MCLK",
+			  "WF_CAM_CLK",
+			  "EDP_BRIJ_I2C_SDA",
+			  "EDP_BRIJ_I2C_SCL",
+			  "UF_CAM_SDA",
+			  "UF_CAM_SCL",
+			  "WF_CAM_SDA",
+			  "WF_CAM_SCL",
+			  "AVEE_LCD_EN",
+			  "",
+			  "AMP_EN",
+			  "AMP_EN2",
+			  "AP_SAR_SENSOR_SDA",
+			  "AP_SAR_SENSOR_SCL",
+			  "SEL_LCM",
+			  "HP_IRQ",
+			  "WF_CAM_RST_L",
+			  "UF_CAM_RST_L",
+			  "AP_BRD_ID2",
+			  "BRIJ_SUSPEND",
+			  "AP_BRD_ID0",
+			  "AP_H1_SPI_MISO",
+			  "AP_H1_SPI_MOSI",
+			  "AP_H1_SPI_CLK",
+			  "AP_H1_SPI_CS_L",
+			  "BT_UART_CTS",
+			  "BT_UART_RTS",
+			  "BT_UART_TXD",
+			  "BT_UART_RXD",
+			  "H1_AP_INT_ODL",
+			  "",
+			  "UART_AP_TX_DBG_RX",
+			  "UART_DBG_TX_AP_RX",
+			  "HP_I2C_SDA",
+			  "HP_I2C_SCL",
+			  "FORCED_USB_BOOT",
+			  "AMP_BCLK",
+			  "AMP_LRCLK",
+			  "AMP_DIN",
+			  "AMP_DIN_2",
+			  "HP_BCLK",
+			  "HP_LRCLK",
+			  "HP_DOUT",
+			  "HP_DIN",
+			  "HP_MCLK",
+			  "AP_SKU_ID0",
+			  "AP_EC_SPI_MISO",
+			  "AP_EC_SPI_MOSI",
+			  "AP_EC_SPI_CLK",
+			  "AP_EC_SPI_CS_L",
+			  "AP_SPI_CLK",
+			  "AP_SPI_MOSI",
+			  "AP_SPI_MISO",
+			  /*
+			   * AP_FLASH_WP_L is crossystem ABI. Schematics
+			   * call it BIOS_FLASH_WP_L.
+			   */
+			  "AP_FLASH_WP_L",
+			  "EN_PP3300_DX_EDP",
+			  "AP_SPI_CS0_L",
+			  "SD_CD_ODL",
+			  "",
+			  "",
+			  "",
+			  "WLAN_SW_CTRL",
+			  "",
+			  "REPORT_E",
+			  "VDD_RESET_1.8V",
+			  "ID0",
+			  "",
+			  "ID1",
+			  "AVDD_LCD_EN",
+			  "MIPI_1.8V_EN",
+			  "",
+			  "CODEC_PWR_EN",
+			  "HUB_EN",
+			  "",
+			  "PP1800_MIPI_SW_EN",
+			  "EN_PP3300_TOUCH",
+			  "",
+			  "",
+			  "AP_SKU_ID1",
+			  "AP_RST_REQ",
+			  "",
+			  "AP_BRD_ID1",
+			  "AP_EC_INT_L",
+			  "SDM_GRFC_3",
+			  "",
+			  "",
+			  "BOOT_CONFIG_4",
+			  "BOOT_CONFIG_2",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "EDP_BRIJ_EN",
+			  "",
+			  "",
+			  "BOOT_CONFIG_3",
+			  "WCI2_LTE_COEX_TXD",
+			  "WCI2_LTE_COEX_RXD",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "FORCED_USB_BOOT_POL",
+			  "AP_TS_PEN_I2C_SDA",
+			  "AP_TS_PEN_I2C_SCL",
+			  "DP_HOT_PLUG_DET",
+			  "EC_IN_RW_ODL";
+
+	en_pp3300_touch: en-pp3300-touch {
+		pinmux {
+			pins = "gpio87";
+			function = "gpio";
+		};
+
+		pinconf {
+			pins = "gpio87";
+			drive-strength = <2>;
+			bias-disable;
+		};
+	};
+};
diff --git a/arch/arm64/boot/dts/qcom/sc7180-trogdor-lazor.dtsi b/arch/arm64/boot/dts/qcom/sc7180-trogdor-lazor.dtsi
index 00535aaa43c9..8b79fbb75756 100644
--- a/arch/arm64/boot/dts/qcom/sc7180-trogdor-lazor.dtsi
+++ b/arch/arm64/boot/dts/qcom/sc7180-trogdor-lazor.dtsi
@@ -11,6 +11,7 @@ ap_ec_spi: &spi6 {};
 ap_h1_spi: &spi0 {};
 
 #include "sc7180-trogdor.dtsi"
+#include "sc7180-trogdor-ti-sn65dsi86.dtsi"
 
 &ap_sar_sensor {
 	semtech,cs0-ground;
@@ -54,6 +55,18 @@ ap_ts_pen_1v8: &i2c4 {
 	compatible = "boe,nv133fhm-n62";
 };
 
+&pm6150_adc {
+	status = "disabled";
+
+	/delete-node/ charger-thermistor@4f;
+};
+
+&pm6150_adc_tm {
+	status = "disabled";
+
+	/delete-node/ charger-thermistor@0;
+};
+
 &trackpad {
 	interrupts = <58 IRQ_TYPE_EDGE_FALLING>;
 };
diff --git a/arch/arm64/boot/dts/qcom/sc7180-trogdor-lte-sku.dtsi b/arch/arm64/boot/dts/qcom/sc7180-trogdor-lte-sku.dtsi
index 469aad4e5948..fd4b71203754 100644
--- a/arch/arm64/boot/dts/qcom/sc7180-trogdor-lte-sku.dtsi
+++ b/arch/arm64/boot/dts/qcom/sc7180-trogdor-lte-sku.dtsi
@@ -17,3 +17,14 @@
 	firmware-name = "qcom/sc7180-trogdor/modem/mba.mbn",
 			"qcom/sc7180-trogdor/modem/qdsp6sw.mbn";
 };
+
+&ipa {
+	status = "okay";
+
+	/*
+	 * Trogdor doesn't have QHEE (Qualcomm's EL2 blob), so the
+	 * modem needs to cover certain init steps (GSI init), and
+	 * the AP needs to wait for it.
+	 */
+	modem-init;
+};
diff --git a/arch/arm64/boot/dts/qcom/sc7180-trogdor-parade-ps8640.dtsi b/arch/arm64/boot/dts/qcom/sc7180-trogdor-parade-ps8640.dtsi
new file mode 100644
index 000000000000..a3d69540d4e4
--- /dev/null
+++ b/arch/arm64/boot/dts/qcom/sc7180-trogdor-parade-ps8640.dtsi
@@ -0,0 +1,109 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Google Trogdor dts fragment for the boards with Parade ps8640 edp bridge
+ *
+ * Copyright 2021 Google LLC.
+ */
+
+/ {
+	pp3300_brij_ps8640: pp3300-brij-ps8640 {
+		compatible = "regulator-fixed";
+		status = "okay";
+		regulator-name = "pp3300_brij_ps8640";
+
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+
+		gpio = <&tlmm 32 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&en_pp3300_edp_brij_ps8640>;
+
+		vin-supply = <&pp3300_a>;
+	};
+};
+
+&dsi0_out {
+	remote-endpoint = <&ps8640_in>;
+};
+
+edp_brij_i2c: &i2c2 {
+	status = "okay";
+	clock-frequency = <400000>;
+
+	ps8640_bridge: bridge@8 {
+		compatible = "parade,ps8640";
+		reg = <0x8>;
+
+		powerdown-gpios = <&tlmm 104 GPIO_ACTIVE_LOW>;
+		reset-gpios = <&tlmm 11 GPIO_ACTIVE_LOW>;
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&edp_brij_en>, <&edp_brij_ps8640_rst>;
+
+		vdd12-supply = <&pp1200_brij>;
+		vdd33-supply = <&pp3300_brij_ps8640>;
+
+		ports {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			port@0 {
+				reg = <0>;
+				ps8640_in: endpoint {
+					remote-endpoint = <&dsi0_out>;
+				};
+			};
+
+			port@1 {
+				reg = <1>;
+				ps8640_out: endpoint {
+					remote-endpoint = <&panel_in_edp>;
+				};
+			};
+		};
+
+		aux-bus {
+			panel: panel {
+				/* Compatible will be filled in per-board */
+				power-supply = <&pp3300_dx_edp>;
+				backlight = <&backlight>;
+
+				port {
+					panel_in_edp: endpoint {
+						remote-endpoint = <&ps8640_out>;
+					};
+				};
+			};
+		};
+	};
+};
+
+&tlmm {
+	edp_brij_ps8640_rst: edp-brij-ps8640-rst {
+		pinmux {
+			pins = "gpio11";
+			function = "gpio";
+		};
+
+		pinconf {
+			pins = "gpio11";
+			drive-strength = <2>;
+			bias-disable;
+		};
+	};
+
+	en_pp3300_edp_brij_ps8640: en-pp3300-edp-brij-ps8640 {
+		pinmux {
+			pins = "gpio32";
+			function = "gpio";
+		};
+
+		pinconf {
+			pins = "gpio32";
+			drive-strength = <2>;
+			bias-disable;
+		};
+	};
+};
diff --git a/arch/arm64/boot/dts/qcom/sc7180-trogdor-pompom-r1.dts b/arch/arm64/boot/dts/qcom/sc7180-trogdor-pompom-r1.dts
index e122a6b481ff..76a130bad60a 100644
--- a/arch/arm64/boot/dts/qcom/sc7180-trogdor-pompom-r1.dts
+++ b/arch/arm64/boot/dts/qcom/sc7180-trogdor-pompom-r1.dts
@@ -26,6 +26,14 @@
 	status = "disabled";
 };
 
+&pm6150_adc {
+	/delete-node/ charger-thermistor@4f;
+};
+
+&pm6150_adc_tm {
+	/delete-node/ charger-thermistor@0;
+};
+
 &pp3300_hub {
 	/* pp3300_l7c is used to power the USB hub */
 	/delete-property/regulator-always-on;
diff --git a/arch/arm64/boot/dts/qcom/sc7180-trogdor-pompom-r2.dts b/arch/arm64/boot/dts/qcom/sc7180-trogdor-pompom-r2.dts
index 4f32e6733f4c..88cf2246c18a 100644
--- a/arch/arm64/boot/dts/qcom/sc7180-trogdor-pompom-r2.dts
+++ b/arch/arm64/boot/dts/qcom/sc7180-trogdor-pompom-r2.dts
@@ -22,3 +22,11 @@
 &charger_thermal {
 	status = "disabled";
 };
+
+&pm6150_adc {
+	/delete-node/ charger-thermistor@4f;
+};
+
+&pm6150_adc_tm {
+	/delete-node/ charger-thermistor@0;
+};
diff --git a/arch/arm64/boot/dts/qcom/sc7180-trogdor-pompom.dtsi b/arch/arm64/boot/dts/qcom/sc7180-trogdor-pompom.dtsi
index a246dbd74cc1..e90f99ef5323 100644
--- a/arch/arm64/boot/dts/qcom/sc7180-trogdor-pompom.dtsi
+++ b/arch/arm64/boot/dts/qcom/sc7180-trogdor-pompom.dtsi
@@ -11,6 +11,7 @@ ap_ec_spi: &spi6 {};
 ap_h1_spi: &spi0 {};
 
 #include "sc7180-trogdor.dtsi"
+#include "sc7180-trogdor-ti-sn65dsi86.dtsi"
 
 / {
 	thermal-zones {
@@ -44,7 +45,7 @@ ap_h1_spi: &spi0 {};
 };
 
 &cpu6_thermal {
-	sustainable-power = <948>;
+	sustainable-power = <1124>;
 };
 
 &cpu7_alert0 {
@@ -56,7 +57,7 @@ ap_h1_spi: &spi0 {};
 };
 
 &cpu7_thermal {
-	sustainable-power = <948>;
+	sustainable-power = <1124>;
 };
 
 &cpu8_alert0 {
@@ -68,7 +69,7 @@ ap_h1_spi: &spi0 {};
 };
 
 &cpu8_thermal {
-	sustainable-power = <948>;
+	sustainable-power = <1124>;
 };
 
 &cpu9_alert0 {
@@ -80,7 +81,7 @@ ap_h1_spi: &spi0 {};
 };
 
 &cpu9_thermal {
-	sustainable-power = <948>;
+	sustainable-power = <1124>;
 };
 
 &gpio_keys {
diff --git a/arch/arm64/boot/dts/qcom/sc7180-trogdor-r1.dts b/arch/arm64/boot/dts/qcom/sc7180-trogdor-r1.dts
index 2b522f9e0d8f..457c25499863 100644
--- a/arch/arm64/boot/dts/qcom/sc7180-trogdor-r1.dts
+++ b/arch/arm64/boot/dts/qcom/sc7180-trogdor-r1.dts
@@ -13,6 +13,7 @@ ap_ec_spi: &spi6 {};
 ap_h1_spi: &spi0 {};
 
 #include "sc7180-trogdor.dtsi"
+#include "sc7180-trogdor-ti-sn65dsi86.dtsi"
 
 / {
 	model = "Google Trogdor (rev1+)";
diff --git a/arch/arm64/boot/dts/qcom/sc7180-trogdor-ti-sn65dsi86.dtsi b/arch/arm64/boot/dts/qcom/sc7180-trogdor-ti-sn65dsi86.dtsi
new file mode 100644
index 000000000000..97d5e45abd1d
--- /dev/null
+++ b/arch/arm64/boot/dts/qcom/sc7180-trogdor-ti-sn65dsi86.dtsi
@@ -0,0 +1,90 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Google Trogdor dts fragment for the boards with TI sn65dsi86 edp bridge
+ *
+ * Copyright 2021 Google LLC.
+ */
+
+&dsi0_out {
+	remote-endpoint = <&sn65dsi86_in>;
+	data-lanes = <0 1 2 3>;
+};
+
+edp_brij_i2c: &i2c2 {
+	status = "okay";
+	clock-frequency = <400000>;
+
+	sn65dsi86_bridge: bridge@2d {
+		compatible = "ti,sn65dsi86";
+		reg = <0x2d>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&edp_brij_en>, <&edp_brij_irq>;
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		interrupt-parent = <&tlmm>;
+		interrupts = <11 IRQ_TYPE_LEVEL_HIGH>;
+
+		enable-gpios = <&tlmm 104 GPIO_ACTIVE_HIGH>;
+
+		vpll-supply = <&pp1800_edp_vpll>;
+		vccio-supply = <&pp1800_brij_vccio>;
+		vcca-supply = <&pp1200_brij>;
+		vcc-supply = <&pp1200_brij>;
+
+		clocks = <&rpmhcc RPMH_LN_BB_CLK3>;
+		clock-names = "refclk";
+
+		no-hpd;
+
+		ports {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			port@0 {
+				reg = <0>;
+				sn65dsi86_in: endpoint {
+					remote-endpoint = <&dsi0_out>;
+				};
+			};
+
+			port@1 {
+				reg = <1>;
+				sn65dsi86_out: endpoint {
+					data-lanes = <0 1>;
+					remote-endpoint = <&panel_in_edp>;
+				};
+			};
+		};
+
+		aux-bus {
+			panel: panel {
+				/* Compatible will be filled in per-board */
+				power-supply = <&pp3300_dx_edp>;
+				backlight = <&backlight>;
+				hpd-gpios = <&sn65dsi86_bridge 2 GPIO_ACTIVE_HIGH>;
+
+				port {
+					panel_in_edp: endpoint {
+						remote-endpoint = <&sn65dsi86_out>;
+					};
+				};
+			};
+		};
+	};
+};
+
+&tlmm {
+	edp_brij_irq: edp-brij-irq {
+		pinmux {
+			pins = "gpio11";
+			function = "gpio";
+		};
+
+		pinconf {
+			pins = "gpio11";
+			drive-strength = <2>;
+			bias-pull-down;
+		};
+	};
+};
diff --git a/arch/arm64/boot/dts/qcom/sc7180-trogdor.dtsi b/arch/arm64/boot/dts/qcom/sc7180-trogdor.dtsi
index 70c88c37de32..d4f4441179fc 100644
--- a/arch/arm64/boot/dts/qcom/sc7180-trogdor.dtsi
+++ b/arch/arm64/boot/dts/qcom/sc7180-trogdor.dtsi
@@ -601,15 +601,6 @@
 &dsi0 {
 	status = "okay";
 	vdda-supply = <&vdda_mipi_dsi0_1p2>;
-
-	ports {
-		port@1 {
-			endpoint {
-				remote-endpoint = <&sn65dsi86_in>;
-				data-lanes = <0 1 2 3>;
-			};
-		};
-	};
 };
 
 &dsi_phy {
@@ -617,70 +608,6 @@
 	vdds-supply = <&vdda_mipi_dsi0_pll>;
 };
 
-edp_brij_i2c: &i2c2 {
-	status = "okay";
-	clock-frequency = <400000>;
-
-	sn65dsi86_bridge: bridge@2d {
-		compatible = "ti,sn65dsi86";
-		reg = <0x2d>;
-		pinctrl-names = "default";
-		pinctrl-0 = <&edp_brij_en>, <&edp_brij_irq>;
-		gpio-controller;
-		#gpio-cells = <2>;
-
-		interrupt-parent = <&tlmm>;
-		interrupts = <11 IRQ_TYPE_LEVEL_HIGH>;
-
-		enable-gpios = <&tlmm 104 GPIO_ACTIVE_HIGH>;
-
-		vpll-supply = <&pp1800_edp_vpll>;
-		vccio-supply = <&pp1800_brij_vccio>;
-		vcca-supply = <&pp1200_brij>;
-		vcc-supply = <&pp1200_brij>;
-
-		clocks = <&rpmhcc RPMH_LN_BB_CLK3>;
-		clock-names = "refclk";
-
-		no-hpd;
-
-		ports {
-			#address-cells = <1>;
-			#size-cells = <0>;
-
-			port@0 {
-				reg = <0>;
-				sn65dsi86_in: endpoint {
-					remote-endpoint = <&dsi0_out>;
-				};
-			};
-
-			port@1 {
-				reg = <1>;
-				sn65dsi86_out: endpoint {
-					data-lanes = <0 1>;
-					remote-endpoint = <&panel_in_edp>;
-				};
-			};
-		};
-
-		aux-bus {
-			panel: panel {
-				/* Compatible will be filled in per-board */
-				power-supply = <&pp3300_dx_edp>;
-				backlight = <&backlight>;
-				hpd-gpios = <&sn65dsi86_bridge 2 GPIO_ACTIVE_HIGH>;
-
-				port {
-					panel_in_edp: endpoint {
-						remote-endpoint = <&sn65dsi86_out>;
-					};
-				};
-			};
-		};
-	};
-};
-
 ap_sar_sensor_i2c: &i2c5 {
 	clock-frequency = <400000>;
 
@@ -750,17 +677,6 @@ hp_i2c: &i2c9 {
 	};
 };
 
-&ipa {
-	status = "okay";
-
-	/*
-	 * Trogdor doesn't have QHEE (Qualcomm's EL2 blob), so the
-	 * modem needs to cover certain init steps (GSI init), and
-	 * the AP needs to wait for it.
-	 */
-	modem-init;
-};
-
 &lpass_cpu {
 	status = "okay";
 
@@ -1244,19 +1160,6 @@ ap_spi_fp: &spi10 {
 		};
 	};
 
-	edp_brij_irq: edp-brij-irq {
-		pinmux {
-			pins = "gpio11";
-			function = "gpio";
-		};
-
-		pinconf {
-			pins = "gpio11";
-			drive-strength = <2>;
-			bias-pull-down;
-		};
-	};
-
 	en_pp3300_codec: en-pp3300-codec {
 		pinmux {
 			pins = "gpio83";
@@ -1523,13 +1426,13 @@ ap_spi_fp: &spi10 {
 		pinconf-cmd {
 			pins = "sdc1_cmd";
 			bias-pull-up;
-			drive-strength = <10>;
+			drive-strength = <16>;
 		};
 
 		pinconf-data {
 			pins = "sdc1_data";
 			bias-pull-up;
-			drive-strength = <10>;
+			drive-strength = <16>;
 		};
 
 		pinconf-rclk {
diff --git a/arch/arm64/boot/dts/qcom/sc7180.dtsi b/arch/arm64/boot/dts/qcom/sc7180.dtsi
index c8921e2d6480..faf8b807d0ff 100644
--- a/arch/arm64/boot/dts/qcom/sc7180.dtsi
+++ b/arch/arm64/boot/dts/qcom/sc7180.dtsi
@@ -15,7 +15,6 @@
 #include <dt-bindings/interconnect/qcom,sc7180.h>
 #include <dt-bindings/interrupt-controller/arm-gic.h>
 #include <dt-bindings/phy/phy-qcom-qusb2.h>
-#include <dt-bindings/power/qcom-aoss-qmp.h>
 #include <dt-bindings/power/qcom-rpmpd.h>
 #include <dt-bindings/reset/qcom,sdm845-aoss.h>
 #include <dt-bindings/reset/qcom,sdm845-pdc.h>
@@ -137,8 +136,8 @@
 			cpu-idle-states = <&LITTLE_CPU_SLEEP_0
 					   &LITTLE_CPU_SLEEP_1
 					   &CLUSTER_SLEEP_0>;
-			capacity-dmips-mhz = <1024>;
-			dynamic-power-coefficient = <100>;
+			capacity-dmips-mhz = <415>;
+			dynamic-power-coefficient = <137>;
 			operating-points-v2 = <&cpu0_opp_table>;
 			interconnects = <&gem_noc MASTER_APPSS_PROC 3 &mc_virt SLAVE_EBI1 3>,
 					<&osm_l3 MASTER_OSM_L3_APPS &osm_l3 SLAVE_OSM_L3>;
@@ -162,8 +161,8 @@
 			cpu-idle-states = <&LITTLE_CPU_SLEEP_0
 					   &LITTLE_CPU_SLEEP_1
 					   &CLUSTER_SLEEP_0>;
-			capacity-dmips-mhz = <1024>;
-			dynamic-power-coefficient = <100>;
+			capacity-dmips-mhz = <415>;
+			dynamic-power-coefficient = <137>;
 			next-level-cache = <&L2_100>;
 			operating-points-v2 = <&cpu0_opp_table>;
 			interconnects = <&gem_noc MASTER_APPSS_PROC 3 &mc_virt SLAVE_EBI1 3>,
@@ -184,8 +183,8 @@
 			cpu-idle-states = <&LITTLE_CPU_SLEEP_0
 					   &LITTLE_CPU_SLEEP_1
 					   &CLUSTER_SLEEP_0>;
-			capacity-dmips-mhz = <1024>;
-			dynamic-power-coefficient = <100>;
+			capacity-dmips-mhz = <415>;
+			dynamic-power-coefficient = <137>;
 			next-level-cache = <&L2_200>;
 			operating-points-v2 = <&cpu0_opp_table>;
 			interconnects = <&gem_noc MASTER_APPSS_PROC 3 &mc_virt SLAVE_EBI1 3>,
@@ -206,8 +205,8 @@
 			cpu-idle-states = <&LITTLE_CPU_SLEEP_0
 					   &LITTLE_CPU_SLEEP_1
 					   &CLUSTER_SLEEP_0>;
-			capacity-dmips-mhz = <1024>;
-			dynamic-power-coefficient = <100>;
+			capacity-dmips-mhz = <415>;
+			dynamic-power-coefficient = <137>;
 			next-level-cache = <&L2_300>;
 			operating-points-v2 = <&cpu0_opp_table>;
 			interconnects = <&gem_noc MASTER_APPSS_PROC 3 &mc_virt SLAVE_EBI1 3>,
@@ -228,8 +227,8 @@
 			cpu-idle-states = <&LITTLE_CPU_SLEEP_0
 					   &LITTLE_CPU_SLEEP_1
 					   &CLUSTER_SLEEP_0>;
-			capacity-dmips-mhz = <1024>;
-			dynamic-power-coefficient = <100>;
+			capacity-dmips-mhz = <415>;
+			dynamic-power-coefficient = <137>;
 			next-level-cache = <&L2_400>;
 			operating-points-v2 = <&cpu0_opp_table>;
 			interconnects = <&gem_noc MASTER_APPSS_PROC 3 &mc_virt SLAVE_EBI1 3>,
@@ -250,8 +249,8 @@
 			cpu-idle-states = <&LITTLE_CPU_SLEEP_0
 					   &LITTLE_CPU_SLEEP_1
 					   &CLUSTER_SLEEP_0>;
-			capacity-dmips-mhz = <1024>;
-			dynamic-power-coefficient = <100>;
+			capacity-dmips-mhz = <415>;
+			dynamic-power-coefficient = <137>;
 			next-level-cache = <&L2_500>;
 			operating-points-v2 = <&cpu0_opp_table>;
 			interconnects = <&gem_noc MASTER_APPSS_PROC 3 &mc_virt SLAVE_EBI1 3>,
@@ -272,8 +271,8 @@
 			cpu-idle-states = <&BIG_CPU_SLEEP_0
 					   &BIG_CPU_SLEEP_1
 					   &CLUSTER_SLEEP_0>;
-			capacity-dmips-mhz = <1740>;
-			dynamic-power-coefficient = <405>;
+			capacity-dmips-mhz = <1024>;
+			dynamic-power-coefficient = <480>;
 			next-level-cache = <&L2_600>;
 			operating-points-v2 = <&cpu6_opp_table>;
 			interconnects = <&gem_noc MASTER_APPSS_PROC 3 &mc_virt SLAVE_EBI1 3>,
@@ -294,8 +293,8 @@
 			cpu-idle-states = <&BIG_CPU_SLEEP_0
 					   &BIG_CPU_SLEEP_1
 					   &CLUSTER_SLEEP_0>;
-			capacity-dmips-mhz = <1740>;
-			dynamic-power-coefficient = <405>;
+			capacity-dmips-mhz = <1024>;
+			dynamic-power-coefficient = <480>;
 			next-level-cache = <&L2_700>;
 			operating-points-v2 = <&cpu6_opp_table>;
 			interconnects = <&gem_noc MASTER_APPSS_PROC 3 &mc_virt SLAVE_EBI1 3>,
@@ -1922,14 +1921,15 @@
 			clock-names = "iface", "bus", "nav", "snoc_axi",
 				      "mnoc_axi", "xo";
 
-			power-domains = <&aoss_qmp AOSS_QMP_LS_MODEM>,
-					<&rpmhpd SC7180_CX>,
+			power-domains = <&rpmhpd SC7180_CX>,
 					<&rpmhpd SC7180_MX>,
 					<&rpmhpd SC7180_MSS>;
-			power-domain-names = "load_state", "cx", "mx", "mss";
+			power-domain-names = "cx", "mx", "mss";
 
 			memory-region = <&mpss_mem>;
 
+			qcom,qmp = <&aoss_qmp>;
+
 			qcom,smem-states = <&modem_smp2p_out 0>;
 			qcom,smem-state-names = "stop";
 
@@ -2647,7 +2647,7 @@
 		};
 
 		qspi: spi@88dc000 {
-			compatible = "qcom,qspi-v1";
+			compatible = "qcom,sc7180-qspi", "qcom,qspi-v1";
 			reg = <0 0x088dc000 0 0x600>;
 			#address-cells = <1>;
 			#size-cells = <0>;
@@ -3219,12 +3219,16 @@
 
 		aoss_qmp: power-controller@c300000 {
 			compatible = "qcom,sc7180-aoss-qmp";
-			reg = <0 0x0c300000 0 0x100000>;
+			reg = <0 0x0c300000 0 0x400>;
 			interrupts = <GIC_SPI 389 IRQ_TYPE_EDGE_RISING>;
 			mboxes = <&apss_shared 0>;
 
 			#clock-cells = <0>;
-			#power-domain-cells = <1>;
+		};
+
+		sram@c3f0000 {
+			compatible = "qcom,rpmh-stats";
+			reg = <0 0x0c3f0000 0 0x400>;
 		};
 
 		spmi_bus: spmi@c440000 {
@@ -3246,6 +3250,21 @@
 			cell-index = <0>;
 		};
 
+		imem@146aa000 {
+			compatible = "simple-mfd";
+			reg = <0 0x146aa000 0 0x2000>;
+
+			#address-cells = <1>;
+			#size-cells = <1>;
+
+			ranges = <0 0 0x146aa000 0x2000>;
+
+			pil-reloc@94c {
+				compatible = "qcom,pil-reloc-info";
+				reg = <0x94c 0xc8>;
+			};
+		};
+
 		apps_smmu: iommu@15000000 {
 			compatible = "qcom,sc7180-smmu-500", "arm,mmu-500";
 			reg = <0 0x15000000 0 0x100000>;
@@ -3616,7 +3635,7 @@
 			polling-delay = <0>;
 
 			thermal-sensors = <&tsens0 1>;
-			sustainable-power = <768>;
+			sustainable-power = <1052>;
 
 			trips {
 				cpu0_alert0: trip-point0 {
@@ -3665,7 +3684,7 @@
 			polling-delay = <0>;
 
 			thermal-sensors = <&tsens0 2>;
-			sustainable-power = <768>;
+			sustainable-power = <1052>;
 
 			trips {
 				cpu1_alert0: trip-point0 {
@@ -3714,7 +3733,7 @@
 			polling-delay = <0>;
 
 			thermal-sensors = <&tsens0 3>;
-			sustainable-power = <768>;
+			sustainable-power = <1052>;
 
 			trips {
 				cpu2_alert0: trip-point0 {
@@ -3763,7 +3782,7 @@
 			polling-delay = <0>;
 
 			thermal-sensors = <&tsens0 4>;
-			sustainable-power = <768>;
+			sustainable-power = <1052>;
 
 			trips {
 				cpu3_alert0: trip-point0 {
@@ -3812,7 +3831,7 @@
 			polling-delay = <0>;
 
 			thermal-sensors = <&tsens0 5>;
-			sustainable-power = <768>;
+			sustainable-power = <1052>;
 
 			trips {
 				cpu4_alert0: trip-point0 {
@@ -3861,7 +3880,7 @@
 			polling-delay = <0>;
 
 			thermal-sensors = <&tsens0 6>;
-			sustainable-power = <768>;
+			sustainable-power = <1052>;
 
 			trips {
 				cpu5_alert0: trip-point0 {
@@ -3910,7 +3929,7 @@
 			polling-delay = <0>;
 
 			thermal-sensors = <&tsens0 9>;
-			sustainable-power = <1202>;
+			sustainable-power = <1425>;
 
 			trips {
 				cpu6_alert0: trip-point0 {
@@ -3951,7 +3970,7 @@
 			polling-delay = <0>;
 
 			thermal-sensors = <&tsens0 10>;
-			sustainable-power = <1202>;
+			sustainable-power = <1425>;
 
 			trips {
 				cpu7_alert0: trip-point0 {
@@ -3992,7 +4011,7 @@
 			polling-delay = <0>;
 
 			thermal-sensors = <&tsens0 11>;
-			sustainable-power = <1202>;
+			sustainable-power = <1425>;
 
 			trips {
 				cpu8_alert0: trip-point0 {
@@ -4033,7 +4052,7 @@
 			polling-delay = <0>;
 
 			thermal-sensors = <&tsens0 12>;
-			sustainable-power = <1202>;
+			sustainable-power = <1425>;
 
 			trips {
 				cpu9_alert0: trip-point0 {
diff --git a/arch/arm64/boot/dts/qcom/sc7280-herobrine.dts b/arch/arm64/boot/dts/qcom/sc7280-herobrine.dts
new file mode 100644
index 000000000000..7a92679a688b
--- /dev/null
+++ b/arch/arm64/boot/dts/qcom/sc7280-herobrine.dts
@@ -0,0 +1,14 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Google Herobrine board device tree source
+ *
+ * Copyright 2021 Google LLC.
+ */
+
+#include "sc7280-herobrine.dtsi"
+
+/ {
+	model = "Google Herobrine";
+	compatible = "google,herobrine",
+		     "qcom,sc7280";
+};
diff --git a/arch/arm64/boot/dts/qcom/sc7280-herobrine.dtsi b/arch/arm64/boot/dts/qcom/sc7280-herobrine.dtsi
new file mode 100644
index 000000000000..4619fa9fcacd
--- /dev/null
+++ b/arch/arm64/boot/dts/qcom/sc7280-herobrine.dtsi
@@ -0,0 +1,1412 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Google Herobrine board device tree source
+ *
+ * Copyright 2021 Google LLC.
+ */
+
+/dts-v1/;
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/iio/qcom,spmi-adc7-pmk8350.h>
+#include <dt-bindings/iio/qcom,spmi-adc7-pmr735a.h>
+#include <dt-bindings/input/gpio-keys.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/pinctrl/qcom,pmic-gpio.h>
+#include <dt-bindings/regulator/qcom,rpmh-regulator.h>
+
+#include "sc7280.dtsi"
+
+/* PMICs depend on spmi_bus label and so must come after SoC */
+#include "pm7325.dtsi"
+#include "pm8350c.dtsi"
+#include "pmk8350.dtsi"
+
+/*
+ * Reserved memory changes
+ *
+ * Delete all unused memory nodes and define the peripheral memory regions
+ * required by the board dts.
+ *
+ */
+
+/delete-node/ &hyp_mem;
+/delete-node/ &xbl_mem;
+/delete-node/ &sec_apps_mem;
+
+/* Increase the size from 2MB to 8MB */
+&rmtfs_mem {
+	reg = <0x0 0x83600000 0x0 0x800000>;
+};
+
+/ {
+	reserved-memory {
+		adsp_mem: memory@86700000 {
+			reg = <0x0 0x86700000 0x0 0x2800000>;
+			no-map;
+		};
+
+		camera_mem: memory@8ad00000 {
+			reg = <0x0 0x8ad00000 0x0 0x500000>;
+			no-map;
+		};
+
+		venus_mem: memory@8b200000 {
+			reg = <0x0 0x8b200000 0x0 0x500000>;
+			no-map;
+		};
+
+		mpss_mem: memory@8b800000 {
+			reg = <0x0 0x8b800000 0x0 0xf600000>;
+			no-map;
+		};
+
+		wpss_mem: memory@9ae00000 {
+			reg = <0x0 0x9ae00000 0x0 0x1900000>;
+			no-map;
+		};
+
+		mba_mem: memory@9c700000 {
+			reg = <0x0 0x9c700000 0x0 0x200000>;
+			no-map;
+		};
+	};
+
+	aliases {
+		serial0 = &uart5;
+		serial1 = &uart7;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	/* FIXED REGULATORS - parents above children */
+
+	/* This is the top level supply and variable voltage */
+	ppvar_sys: ppvar-sys-regulator {
+		compatible = "regulator-fixed";
+		regulator-name = "ppvar_sys";
+		regulator-always-on;
+		regulator-boot-on;
+	};
+
+	/* This divides ppvar_sys by 2, so voltage is variable */
+	src_vph_pwr: src-vph-pwr-regulator {
+		compatible = "regulator-fixed";
+		regulator-name = "src_vph_pwr";
+
+		/* EC turns on with switchcap_on; always on for AP */
+		regulator-always-on;
+		regulator-boot-on;
+
+		vin-supply = <&ppvar_sys>;
+	};
+
+	pp5000_s3: pp5000-s3-regulator {
+		compatible = "regulator-fixed";
+		regulator-name = "pp5000_s3";
+
+		/* EC turns on with en_pp5000_s3; always on for AP */
+		regulator-always-on;
+		regulator-boot-on;
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+
+		vin-supply = <&ppvar_sys>;
+	};
+
+	pp3300_z1: pp3300-z1-regulator {
+		compatible = "regulator-fixed";
+		regulator-name = "pp3300_z1";
+
+		/* EC turns on with en_pp3300_z1; always on for AP */
+		regulator-always-on;
+		regulator-boot-on;
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+
+		vin-supply = <&ppvar_sys>;
+	};
+
+	pp3300_audio:
+	pp3300_codec: pp3300-codec-regulator {
+		compatible = "regulator-fixed";
+		regulator-name = "pp3300_codec";
+
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+
+		gpio = <&tlmm 67 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+		pinctrl-names = "default";
+		pinctrl-0 = <&en_pp3300_codec>;
+
+		vin-supply = <&pp3300_z1>;
+	};
+
+	pp3300_cam:
+	pp3300_edp:
+	pp3300_ts: pp3300-edp-regulator {
+		compatible = "regulator-fixed";
+		regulator-name = "pp3300_edp";
+
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+
+		gpio = <&tlmm 80 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+		pinctrl-names = "default";
+		pinctrl-0 = <&en_pp3300_dx_edp>;
+
+		vin-supply = <&pp3300_z1>;
+	};
+
+	pp3300_fp:
+	pp3300_fp_ls:
+	pp3300_mcu: pp3300-fp-regulator {
+		compatible = "regulator-fixed";
+		regulator-name = "pp3300_fp";
+
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+
+		regulator-boot-on;
+		regulator-always-on;
+
+		/*
+		 * WARNING: it is intentional that GPIO 42 isn't listed here.
+		 * The userspace script for updating the fingerprint firmware
+		 * needs to control the FP regulators during a FW update,
+		 * hence the signal can't be owned by the kernel regulator.
+		 */
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&en_fp_rails>;
+
+		vin-supply = <&pp3300_z1>;
+	};
+
+	pp3300_hub: pp3300-hub-regulator {
+		compatible = "regulator-fixed";
+		regulator-name = "pp3300_hub";
+
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+
+		regulator-boot-on;
+		regulator-always-on;
+
+		gpio = <&tlmm 24 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+		pinctrl-names = "default";
+		pinctrl-0 = <&en_pp3300_hub>;
+
+		vin-supply = <&pp3300_z1>;
+	};
+
+	pp3300_tp: pp3300-tp-regulator {
+		compatible = "regulator-fixed";
+		regulator-name = "pp3300_tp";
+
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+
+		/* AP turns on with PP1800_L18B_S0; always on for AP */
+		regulator-always-on;
+		regulator-boot-on;
+
+		vin-supply = <&pp3300_z1>;
+	};
+
+	pp2850_uf_cam: pp2850-uf-cam {
+		compatible = "regulator-fixed";
+		regulator-name = "pp2850_uf_cam";
+
+		regulator-min-microvolt = <2850000>;
+		regulator-max-microvolt = <2850000>;
+
+		gpio = <&tlmm 6 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+		pinctrl-names = "default";
+		pinctrl-0 = <&uf_cam_en>;
+
+		vin-supply = <&pp3300_cam>;
+	};
+
+	pp2850_vcm_wf_cam: pp2850-vcm-wf-cam {
+		compatible = "regulator-fixed";
+		regulator-name = "pp2850_vcm_wf_cam";
+
+		regulator-min-microvolt = <2850000>;
+		regulator-max-microvolt = <2850000>;
+
+		gpio = <&tlmm 7 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+		pinctrl-names = "default";
+		pinctrl-0 = <&wf_cam_en>;
+
+		vin-supply = <&pp3300_cam>;
+	};
+
+	pp2850_wf_cam: pp2850-wf-cam {
+		compatible = "regulator-fixed";
+		regulator-name = "pp2850_wf_cam";
+
+		regulator-min-microvolt = <2850000>;
+		regulator-max-microvolt = <2850000>;
+
+		gpio = <&tlmm 7 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+		/*
+		 * The pinconf can only be referenced once so we put it on the
+		 * first regulator and comment it out here.
+		 *
+		 * pinctrl-names = "default";
+		 * pinctrl-0 = <&wf_cam_en>;
+		 */
+
+		vin-supply = <&pp3300_cam>;
+	};
+
+	pp1800_fp: pp1800-fp-regulator {
+		compatible = "regulator-fixed";
+		regulator-name = "pp1800_fp";
+
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+
+		regulator-boot-on;
+		regulator-always-on;
+
+		/*
+		 * WARNING: it is intentional that GPIO 42 isn't listed here.
+		 * The userspace script for updating the fingerprint firmware
+		 * needs to control the FP regulators during a FW update,
+		 * hence the signal can't be owned by the kernel regulator.
+		 */
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&en_fp_rails>;
+
+		vin-supply = <&pp1800_l18b_s0>;
+		status = "disabled";
+	};
+
+	pp1800_uf_cam: pp1800-uf-cam {
+		compatible = "regulator-fixed";
+		regulator-name = "pp1800_uf_cam";
+
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+
+		gpio = <&tlmm 6 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+		/*
+		 * The pinconf can only be referenced once so we put it on the
+		 * first regulator and comment it out here.
+		 *
+		 * pinctrl-names = "default";
+		 * pinctrl-0 = <&uf_cam_en>;
+		 */
+
+		vin-supply = <&pp1800_l19b>;
+	};
+
+	pp1800_wf_cam: pp1800-wf-cam {
+		compatible = "regulator-fixed";
+		regulator-name = "pp1800_wf_cam";
+
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+
+		gpio = <&tlmm 7 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+		/*
+		 * The pinconf can only be referenced once so we put it on the
+		 * first regulator and comment it out here.
+		 *
+		 * pinctrl-names = "default";
+		 * pinctrl-0 = <&wf_cam_en>;
+		 */
+
+		vin-supply = <&pp1800_l19b>;
+	};
+
+	pp1200_wf_cam: pp1200-wf-cam {
+		compatible = "regulator-fixed";
+		regulator-name = "pp1200_wf_cam";
+
+		regulator-min-microvolt = <1200000>;
+		regulator-max-microvolt = <1200000>;
+
+		gpio = <&tlmm 7 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+		/*
+		 * The pinconf can only be referenced once so we put it on the
+		 * first regulator and comment it out here.
+		 *
+		 * pinctrl-names = "default";
+		 * pinctrl-0 = <&wf_cam_en>;
+		 */
+
+		vin-supply = <&pp1200_l6b>;
+	};
+
+	/* BOARD-SPECIFIC TOP LEVEL NODES */
+
+	gpio_keys: gpio-keys {
+		compatible = "gpio-keys";
+		status = "disabled";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pen_pdct_l>;
+
+		pen_insert: pen-insert {
+			label = "Pen Insert";
+
+			/* Insert = low, eject = high */
+			gpios = <&tlmm 39 GPIO_ACTIVE_LOW>;
+			linux,code = <SW_PEN_INSERTED>;
+			linux,input-type = <EV_SW>;
+			wakeup-event-action = <EV_ACT_DEASSERTED>;
+			wakeup-source;
+		};
+	};
+
+	pwmleds {
+		compatible = "pwm-leds";
+		status = "disabled";
+		keyboard_backlight: keyboard-backlight {
+			status = "disabled";
+			label = "cros_ec::kbd_backlight";
+			pwms = <&cros_ec_pwm 0>;
+			max-brightness = <1023>;
+		};
+	};
+};
+
+&apps_rsc {
+	pm7325-regulators {
+		compatible = "qcom,pm7325-rpmh-regulators";
+		qcom,pmic-id = "b";
+
+		vdd19_pmu_pcie_i:
+		vdd19_pmu_rfa_i:
+		vreg_s1b_wlan:
+		vreg_s1b: smps1 {
+			regulator-min-microvolt = <1856000>;
+			regulator-max-microvolt = <2040000>;
+		};
+
+		vdd_pmu_aon_i:
+		vreg_s7b_wlan:
+		vreg_s7b: smps7 {
+			regulator-min-microvolt = <535000>;
+			regulator-max-microvolt = <1120000>;
+		};
+
+		vdd13_pmu_pcie_i:
+		vdd13_pmu_rfa_i:
+		vreg_s8b_wlan:
+		vreg_s8b: smps8 {
+			regulator-min-microvolt = <1256000>;
+			regulator-max-microvolt = <1500000>;
+		};
+
+		vdda_usb_ss_dp_core:
+		vreg_l1b: ldo1 {
+			regulator-min-microvolt = <825000>;
+			regulator-max-microvolt = <925000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vdda_usb_hs0_3p1:
+		vreg_l2b: ldo2 {
+			regulator-min-microvolt = <2700000>;
+			regulator-max-microvolt = <3544000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		pp1200_l6b:
+		vdd_ufs_1p2:
+		vdd_vref:
+		vdda_csi01_1p2:
+		vdda_csi23_1p2:
+		vdda_csi4_1p2:
+		vdda_dsi0_1p2:
+		vdda_pcie0_1p2:
+		vdda_pcie1_1p2:
+		vdda_usb_ss_dp_1p2:
+		vdda_qlink0_1p2_ck:
+		vdda_qlink1_1p2_ck:
+		vreg_l6b_1p2:
+		vreg_l6b: ldo6 {
+			regulator-min-microvolt = <1120000>;
+			regulator-max-microvolt = <1408000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		pp2950_l7b:
+		vreg_l7b: ldo7 {
+			regulator-min-microvolt = <2960000>;
+			regulator-max-microvolt = <2960000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		codec_vcc:
+		pp1800_l18b_s0:
+		pp1800_ts:
+		vdd1:
+		vddpx_0:
+		vddpx_3:
+		vddpx_7:
+		vreg_l18b: ldo18 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <2000000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		pp1800_l19b:
+		vddpx_ts:
+		vddpx_wl4otp:
+		vreg_l19b: ldo19 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+	};
+
+	pm8350c-regulators {
+		compatible = "qcom,pm8350c-rpmh-regulators";
+		qcom,pmic-id = "c";
+
+		vreg_s1c: smps1 {
+			regulator-min-microvolt = <2190000>;
+			regulator-max-microvolt = <2210000>;
+		};
+
+		vddpx_1:
+		vreg_s9c: smps9 {
+			regulator-min-microvolt = <1010000>;
+			regulator-max-microvolt = <1170000>;
+		};
+
+		pp1800_l1c:
+		pp1800_pen:
+		vdd_a_gfx_cs_1p1:
+		vdd_a_cxo_1p8:
+		vdd_qfprom:
+		vdda_apc_cs_1p8:
+		vdda_qrefs_1p8:
+		vdda_turing_q6_cs_1p8:
+		vdda_usb_hs0_1p8:
+		vreg_l1c: ldo1 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1980000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		dmic_vdd:
+		pp1800_alc5682:
+		pp1800_l2c:
+		pp1800_vreg_alc5682:
+		vreg_l2c: ldo2 {
+			regulator-min-microvolt = <1620000>;
+			regulator-max-microvolt = <1980000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		pp3300_sar:
+		pp3300_sensor:
+		vreg_l3c: ldo3 {
+			regulator-min-microvolt = <2800000>;
+			regulator-max-microvolt = <3540000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		ppvar_uim1:
+		vddpx_5:
+		vreg_l4c: ldo4 {
+			regulator-min-microvolt = <1620000>;
+			regulator-max-microvolt = <3300000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		pp2950_l5c:
+		uim_vcc:
+		vddpx_6:
+		vreg_l5c: ldo5 {
+			regulator-min-microvolt = <1620000>;
+			regulator-max-microvolt = <3300000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		ppvar_l6c:
+		vddpx_2:
+		vreg_l6c: ldo6 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <2950000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l7c: ldo7 {
+			regulator-min-microvolt = <3000000>;
+			regulator-max-microvolt = <3544000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		pp1800_prox:
+		pp1800_sar:
+		vreg_l8c: ldo8 {
+			regulator-min-microvolt = <1620000>;
+			regulator-max-microvolt = <2000000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		pp2950_l9c:
+		vreg_l9c: ldo9 {
+			regulator-min-microvolt = <2960000>;
+			regulator-max-microvolt = <2960000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vdd_a_gnss_0p9:
+		vdd_ufs_core:
+		vdd_usb_hs0_core:
+		vdd_vref_0p9:
+		vdda_csi01_0p9:
+		vdda_csi23_0p9:
+		vdda_csi4_0p9:
+		vdda_dsi0_pll_0p9:
+		vdda_dsi0_0p9:
+		vdda_pcie0_core:
+		vdda_pcie1_core:
+		vdda_qlink0_0p9:
+		vdda_qlink1_0p9:
+		vdda_qlink0_0p9_ck:
+		vdda_qlink1_0p9_ck:
+		vdda_qrefs_0p875:
+		vreg_l10c_0p8:
+		vreg_l10c: ldo10 {
+			regulator-min-microvolt = <720000>;
+			regulator-max-microvolt = <1050000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		pp2800_l11c:
+		vreg_l11c: ldo11 {
+			regulator-min-microvolt = <2800000>;
+			regulator-max-microvolt = <3544000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		pp1800_l12c:
+		vreg_l12c: ldo12 {
+			regulator-min-microvolt = <1650000>;
+			regulator-max-microvolt = <2000000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		pp3300_l13c:
+		vreg_l13c: ldo13 {
+			regulator-min-microvolt = <2700000>;
+			regulator-max-microvolt = <3544000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_bob: bob {
+			regulator-min-microvolt = <3008000>;
+			regulator-max-microvolt = <3960000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_AUTO>;
+		};
+	};
+};
+
+ap_tp_i2c: &i2c1 {
+	status = "okay";
+	clock-frequency = <400000>;
+
+	trackpad: trackpad@15 {
+		compatible = "elan,ekth3000";
+		reg = <0x15>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&tp_int_odl>;
+
+		interrupt-parent = <&tlmm>;
+		interrupts = <102 IRQ_TYPE_EDGE_FALLING>;
+
+		vcc-supply = <&pp3300_z1>;
+
+		wakeup-source;
+	};
+};
+
+ap_h1_i2c: &i2c12 {
+	status = "okay";
+	clock-frequency = <400000>;
+
+	tpm@50 {
+		compatible = "google,cr50";
+		reg = <0x50>;
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&h1_ap_int_odl>;
+
+		interrupt-parent = <&tlmm>;
+		interrupts = <54 IRQ_TYPE_EDGE_RISING>;
+	};
+};
+
+ap_ts_pen: &i2c13 {
+	status = "okay";
+	clock-frequency = <400000>;
+
+	ap_ts: touchscreen@10 {
+		compatible = "hid-over-i2c";
+		reg = <0x10>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&ts_int_l>, <&ts_reset_l>;
+
+		interrupt-parent = <&tlmm>;
+		interrupts = <81 IRQ_TYPE_LEVEL_LOW>;
+
+		post-power-on-delay-ms = <20>;
+		hid-descr-addr = <0x0001>;
+
+		vdd-supply = <&pp3300_ts>;
+	};
+};
+
+&pm7325_gpios {
+	status = "disabled"; /* No GPIOs are connected */
+};
+
+&pmk8350_gpios {
+	status = "disabled"; /* No GPIOs are connected */
+};
+
+&pmk8350_pon {
+	status = "disabled";
+};
+
+&pmk8350_rtc {
+	status = "disabled";
+};
+
+&pmk8350_vadc {
+	pmk8350_die_temp {
+		reg = <PMK8350_ADC7_DIE_TEMP>;
+		label = "pmk8350_die_temp";
+		qcom,pre-scaling = <1 1>;
+	};
+
+	pmr735a_die_temp {
+		reg = <PMR735A_ADC7_DIE_TEMP>;
+		label = "pmr735a_die_temp";
+		qcom,pre-scaling = <1 1>;
+	};
+};
+
+&qfprom {
+	vcc-supply = <&vdd_qfprom>;
+};
+
+&qspi {
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&qspi_clk>, <&qspi_cs0>, <&qspi_data01>;
+
+	flash@0 {
+		compatible = "jedec,spi-nor";
+		reg = <0>;
+
+		spi-max-frequency = <37500000>;
+		spi-tx-bus-width = <2>;
+		spi-rx-bus-width = <2>;
+	};
+};
+
+&qupv3_id_0 {
+	status = "okay";
+};
+
+&qupv3_id_1 {
+	status = "okay";
+};
+
+&sdhc_1 {
+	status = "okay";
+
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&sdc1_on>;
+	pinctrl-1 = <&sdc1_off>;
+	vmmc-supply = <&pp2950_l7b>;
+	vqmmc-supply = <&pp1800_l19b>;
+};
+
+&sdhc_2 {
+	status = "okay";
+
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&sdc2_on>;
+	pinctrl-1 = <&sdc2_off>;
+	vmmc-supply = <&pp2950_l9c>;
+	vqmmc-supply = <&ppvar_l6c>;
+
+	cd-gpios = <&tlmm 91 GPIO_ACTIVE_LOW>;
+};
+
+ap_ec_spi: &spi8 {
+	status = "okay";
+
+	pinctrl-0 = <&qup_spi8_data_clk>, <&qup_spi8_cs_gpio_init_high>, <&qup_spi8_cs_gpio>;
+	cs-gpios = <&tlmm 35 GPIO_ACTIVE_LOW>;
+
+	cros_ec: ec@0 {
+		compatible = "google,cros-ec-spi";
+		reg = <0>;
+		interrupt-parent = <&tlmm>;
+		interrupts = <142 IRQ_TYPE_LEVEL_LOW>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&ap_ec_int_l>;
+		spi-max-frequency = <3000000>;
+
+		cros_ec_pwm: ec-pwm {
+			compatible = "google,cros-ec-pwm";
+			#pwm-cells = <1>;
+		};
+
+		i2c_tunnel: i2c-tunnel {
+			compatible = "google,cros-ec-i2c-tunnel";
+			google,remote-bus = <0>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+
+		typec {
+			compatible = "google,cros-ec-typec";
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			usb_c0: connector@0 {
+				compatible = "usb-c-connector";
+				reg = <0>;
+				label = "left";
+				power-role = "dual";
+				data-role = "host";
+				try-power-role = "source";
+			};
+
+			usb_c1: connector@1 {
+				compatible = "usb-c-connector";
+				reg = <1>;
+				label = "right";
+				power-role = "dual";
+				data-role = "host";
+				try-power-role = "source";
+			};
+		};
+	};
+};
+
+#include <arm/cros-ec-keyboard.dtsi>
+#include <arm/cros-ec-sbs.dtsi>
+
+&keyboard_controller {
+	function-row-physmap = <
+		MATRIX_KEY(0x00, 0x02, 0)	/* T1 */
+		MATRIX_KEY(0x03, 0x02, 0)	/* T2 */
+		MATRIX_KEY(0x02, 0x02, 0)	/* T3 */
+		MATRIX_KEY(0x01, 0x02, 0)	/* T4 */
+		MATRIX_KEY(0x03, 0x04, 0)	/* T5 */
+		MATRIX_KEY(0x02, 0x04, 0)	/* T6 */
+		MATRIX_KEY(0x01, 0x04, 0)	/* T7 */
+		MATRIX_KEY(0x02, 0x09, 0)	/* T8 */
+		MATRIX_KEY(0x01, 0x09, 0)	/* T9 */
+		MATRIX_KEY(0x00, 0x04, 0)	/* T10 */
+	>;
+	linux,keymap = <
+		MATRIX_KEY(0x00, 0x02, KEY_BACK)
+		MATRIX_KEY(0x03, 0x02, KEY_REFRESH)
+		MATRIX_KEY(0x02, 0x02, KEY_ZOOM)
+		MATRIX_KEY(0x01, 0x02, KEY_SCALE)
+		MATRIX_KEY(0x03, 0x04, KEY_SYSRQ)
+		MATRIX_KEY(0x02, 0x04, KEY_BRIGHTNESSDOWN)
+		MATRIX_KEY(0x01, 0x04, KEY_BRIGHTNESSUP)
+		MATRIX_KEY(0x02, 0x09, KEY_MUTE)
+		MATRIX_KEY(0x01, 0x09, KEY_VOLUMEDOWN)
+		MATRIX_KEY(0x00, 0x04, KEY_VOLUMEUP)
+
+		CROS_STD_MAIN_KEYMAP
+	>;
+};
+
+&uart5 {
+	compatible = "qcom,geni-debug-uart";
+	status = "okay";
+};
+
+&uart7 {
+	status = "okay";
+};
+
+&usb_1 {
+	status = "okay";
+};
+
+&usb_1_dwc3 {
+	dr_mode = "host";
+};
+
+&usb_1_hsphy {
+	status = "okay";
+
+	vdda-pll-supply = <&vdd_usb_hs0_core>;
+	vdda33-supply = <&vdda_usb_hs0_3p1>;
+	vdda18-supply = <&vdda_usb_hs0_1p8>;
+};
+
+&usb_1_qmpphy {
+	status = "okay";
+
+	vdda-phy-supply = <&vdda_usb_ss_dp_1p2>;
+	vdda-pll-supply = <&vdda_usb_ss_dp_core>;
+};
+
+&usb_2 {
+	status = "okay";
+};
+
+&usb_2_dwc3 {
+	dr_mode = "host";
+};
+
+&usb_2_hsphy {
+	status = "okay";
+
+	vdda-pll-supply = <&vdd_usb_hs0_core>;
+	vdda33-supply = <&vdda_usb_hs0_3p1>;
+	vdda18-supply = <&vdda_usb_hs0_1p8>;
+};
+
+/* PINCTRL - additions to nodes defined in sc7280.dtsi */
+
+&qspi_cs0 {
+	bias-disable;
+};
+
+&qspi_clk {
+	bias-disable;
+};
+
+&qspi_data01 {
+	/* High-Z when no transfers; nice to park the lines */
+	bias-pull-up;
+};
+
+&qup_uart5_rx {
+	drive-strength = <2>;
+	bias-pull-up;
+};
+
+&qup_uart5_tx {
+	drive-strength = <2>;
+	bias-disable;
+};
+
+&qup_uart7_cts {
+	/*
+	 * Configure a pull-down on CTS to match the pull of
+	 * the Bluetooth module.
+	 */
+	bias-pull-down;
+};
+
+&qup_uart7_rts {
+	/* We'll drive RTS, so no pull */
+	drive-strength = <2>;
+	bias-disable;
+};
+
+&qup_uart7_tx {
+	/* We'll drive TX, so no pull */
+	drive-strength = <2>;
+	bias-disable;
+};
+
+&qup_uart7_rx {
+	/*
+	 * Configure a pull-up on RX. This is needed to avoid
+	 * garbage data when the TX pin of the Bluetooth module is
+	 * in tri-state (module powered off or not driving the
+	 * signal yet).
+	 */
+	bias-pull-up;
+};
+
+&sdc1_on {
+	clk {
+		bias-disable;
+		drive-strength = <16>;
+	};
+
+	cmd {
+		bias-pull-up;
+		drive-strength = <10>;
+	};
+
+	data {
+		bias-pull-up;
+		drive-strength = <10>;
+	};
+
+	rclk {
+		bias-pull-down;
+	};
+};
+
+&sdc2_on {
+	clk {
+		bias-disable;
+		drive-strength = <16>;
+	};
+
+	cmd {
+		bias-pull-up;
+		drive-strength = <10>;
+	};
+
+	data {
+		bias-pull-up;
+		drive-strength = <10>;
+	};
+
+	sd-cd {
+		pins = "gpio91";
+		bias-pull-up;
+	};
+};
+
+/* PINCTRL - board-specific pinctrl */
+
+&pm8350c_gpios {
+	gpio-line-names = "AP_SUSPEND",
+			  "",
+			  "",
+			  "AP_BL_EN",
+			  "",
+			  "SD_CD_ODL",
+			  "",
+			  "",
+			  "AP_BL_PWM";
+
+	ap_bl_en: ap-bl-en {
+		pins = "gpio4";
+		function = "normal";
+		qcom,drive-strength = <PMIC_GPIO_STRENGTH_LOW>;
+		bias-disable;
+
+		/* Force backlight to be disabled to match state at boot. */
+		output-low;
+	};
+};
+
+&tlmm {
+	gpio-line-names = "HP_I2C_SDA",			/* 0 */
+			  "HP_I2C_SCL",
+			  "SSD_RST_L",
+			  "PE_WAKE_ODL",
+			  "AP_TP_I2C_SDA",
+			  "AP_TP_I2C_SCL",
+			  "UF_CAM_EN",
+			  "WF_CAM_EN",
+			  "AP_SAR_SENSOR_SDA",
+			  "AP_SAR_SENSOR_SCL",
+
+			  "",				/* 10 */
+			  "",
+			  "AP_SPI_MOSI",
+			  "AP_SPI_MISO",
+			  "AP_SPI_CLK",
+			  "AP_SPI_CS0_L",
+			  "",
+			  "",
+			  "EDP_HPD",
+			  "",
+
+			  "UF_CAM_RST_L",		/* 20 */
+			  "WF_CAM_RST_L",
+			  "UART_AP_TX_DBG_RX",
+			  "UART_DBG_TX_AP_RX",
+			  "EN_PP3300_HUB",
+			  "",
+			  "HOST2WLAN_SOL",
+			  "WLAN2HOST_SOL",
+			  "BT_UART_CTS",
+			  "BT_UART_RTS",
+
+			  "BT_UART_TXD",		/* 30 */
+			  "BT_UART_RXD",
+			  "AP_EC_SPI_MISO",
+			  "AP_EC_SPI_MOSI",
+			  "AP_EC_SPI_CLK",
+			  "AP_EC_SPI_CS_L",
+			  "",
+			  "",
+			  "",
+			  "PEN_PDCT_L",
+
+			  "IO_BRD_ID0",			/* 40 */
+			  "IO_BRD_ID1",
+			  "EN_FP_RAILS",
+			  "PEN_IRQ_L",
+			  "AP_SPI_FP_MISO",
+			  "AP_SPI_FP_MOSI",
+			  "AP_SPI_FP_CLK",
+			  "AP_SPI_FP_CS_L",
+			  "AP_H1_SPI_MISO",
+			  "AP_H1_SPI_MOSI",
+
+			  "AP_H1_SPI_CLK",		/* 50 */
+			  "AP_H1_SPI_CS_L",
+			  "AP_TS_PEN_I2C_SDA",
+			  "AP_TS_PEN_I2C_SCL",
+			  "H1_AP_INT_ODL",
+			  "",
+			  "LCM_RST_1V8_L",
+			  "AMP_EN",
+			  "",
+			  "DP_HOT_PLUG_DET",
+
+			  "HUB_RST_L",			/* 60 */
+			  "FP_TO_AP_IRQ_L",
+			  "",
+			  "",
+			  "UF_CAM_MCLK",
+			  "WF_CAM_MCLK",
+			  "IO_BRD_ID2",
+			  "EN_PP3300_CODEC",
+			  "EC_IN_RW_ODL",
+			  "UF_CAM_SDA",
+
+			  "UF_CAM_SCL",			/* 70 */
+			  "WF_CAM_SDA",
+			  "WF_CAM_SCL",
+			  "AP_BRD_ID0",
+			  "AP_BRD_ID1",
+			  "AP_BRD_ID2",
+			  "",
+			  "FPMCU_BOOT0",
+			  "FP_RST_L",
+			  "PE_CLKREQ_ODL",
+
+			  "EN_EDP_PP3300",		/* 80 */
+			  "TS_INT_L",
+			  "FORCE_USB_BOOT",
+			  "WCD_RST_L",
+			  "WLAN_EN",
+			  "BT_EN",
+			  "WLAN_SW_CTRL",
+			  "PCIE0_RESET_L",
+			  "PCIE0_CLK_REQ_L",
+			  "PCIE0_WAKE_L",
+
+			  "AS_EN",			/* 90 */
+			  "SD_CD_ODL",
+			  "",
+			  /*
+			   * AP_FLASH_WP_L is crossystem ABI. Schematics
+			   * call it BIOS_FLASH_WP_L.
+			   */
+			  "AP_FLASH_WP_L",
+			  "BT_WLAN_SB_CLK",
+			  "BT_WLAN_SB_DATA",
+			  "HP_MCLK",
+			  "HP_BCLK",
+			  "HP_DOUT",
+			  "HP_DIN",
+
+			  "HP_LRCLK",			/* 100 */
+			  "HP_IRQ",
+			  "TP_INT_ODL",
+			  "",
+			  "IO_SKU_ID2",
+			  "TS_RESET_L",
+			  "AMP_BCLK",
+			  "AMP_DIN",
+			  "AMP_LRCLK",
+			  "UIM2_DATA",
+
+			  "UIM2_CLK",			/* 110 */
+			  "UIM2_RST",
+			  "UIM2_PRESENT",
+			  "UIM1_DATA",
+			  "UIM1_CLK",
+			  "UIM1_RST",
+			  "",
+			  "RFFE0_CLK",
+			  "RFFE0_DATA/BOOT_CONFIG_0",
+			  "RFFE1_CLK",
+
+			  "RFFE1_DATA/BOOT_CONFIG_1",	/* 120 */
+			  "RFFE2_CLK",
+			  "RFFE2_DATA/BOOT_CONFIG_2",
+			  "RFFE3_CLK",
+			  "RFFE3_DATA/BOOT_CONFIG_3",
+			  "RFFE4_CLK",
+			  "RFFE4_DATA",
+			  "WCI2_LTE_COEX_RXD",
+			  "WCI2_LTE_COEX_TXD",
+			  "IO_SKU_ID0",
+
+			  "IO_SKU_ID1",			/* 130 */
+			  "",
+			  "",
+			  "QLINK0_REQ",
+			  "QLINK0_EN",
+			  "QLINK0_WMSS_RESET_L",
+			  "QLINK1_REQ",
+			  "QLINK1_EN",
+			  "QLINK1_WMSS_RESET_L",
+			  "FORCED_USB_BOOT_POL",
+
+			  "",				/* 140 */
+			  "P_SENSOR_INT_L",
+			  "AP_EC_INT_L",
+			  "",
+			  "WCD_SWR_TX_CLK",
+			  "WCD_SWR_TX_DATA_0",
+			  "WCD_SWR_TX_DATA_1",
+			  "WCD_SWR_RX_CLK",
+			  "WCD_SWR_RX_DATA_0",
+			  "WCD_SWR_RX_DATA_1",
+
+			  "",				/* 150 */
+			  "",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "WCD_SWR_TX_DATA_2",
+			  "",
+
+			  "",				/* 160 */
+			  "",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "",
+
+			  "",				/* 170 */
+			  "SENS_UART_TXD",
+			  "SENS_UART_RXD",
+			  "",
+			  "",
+			  "";
+
+	/*
+	 * pinctrl settings for pins that have no real owners.
+	 */
+	pinctrl-names = "default";
+	pinctrl-0 = <&bios_flash_wp_l>;
+
+	amp_en: amp-en {
+		pins = "gpio57";
+		function = "gpio";
+		bias-pull-down;
+	};
+
+	ap_ec_int_l: ap-ec-int-l {
+		pins = "gpio142";
+		input-enable;
+		bias-pull-up;
+	};
+
+	bios_flash_wp_l: bios-flash-wp-l {
+		pins = "gpio93";
+		function = "gpio";
+		input-enable;
+		bias-disable;
+	};
+
+	bt_en: bt-en {
+		pins = "gpio85";
+		function = "gpio";
+		drive-strength = <2>;
+		output-low;
+		bias-pull-down;
+	};
+
+	en_fp_rails: en-fp-rails {
+		pins = "gpio42";
+		drive-strength = <2>;
+		output-high;
+		bias-disable;
+	};
+
+	en_pp3300_codec: en-pp3300-codec {
+		pins = "gpio67";
+		drive-strength = <2>;
+		bias-disable;
+	};
+
+	en_pp3300_dx_edp: en-pp3300-dx-edp {
+		pins = "gpio80";
+		function = "gpio";
+		drive-strength = <2>;
+		/* Has external pulldown */
+		bias-disable;
+	};
+
+	en_pp3300_hub: en-pp3300-hub {
+		pins = "gpio24";
+		function = "gpio";
+		drive-strength = <2>;
+		/* Has external pulldown */
+		bias-disable;
+	};
+
+	fp_to_ap_irq_l: fp-to-ap-irq-l {
+		pins = "gpio61";
+		function = "gpio";
+		input-enable;
+		/* Has external pullup */
+		bias-disable;
+	};
+
+	h1_ap_int_odl: h1-ap-int-odl {
+		pins = "gpio54";
+		function = "gpio";
+		input-enable;
+		bias-pull-up;
+	};
+
+	hp_irq: hp-irq {
+		pins = "gpio101";
+		function = "gpio";
+		bias-pull-up;
+	};
+
+	p_sensor_int_l: p-sensor-int-l {
+		pins = "gpio141";
+		function = "gpio";
+		input-enable;
+		bias-pull-up;
+	};
+
+	pen_irq_l: pen-irq-l {
+		pins = "gpio43";
+		function = "gpio";
+		/* Has external pullup */
+		bias-disable;
+	};
+
+	pen_pdct_l: pen-pdct-l {
+		pins = "gpio39";
+		function = "gpio";
+		/* Has external pullup */
+		bias-disable;
+	};
+
+	qup_spi8_cs_gpio_init_high: qup-spi8-cs-gpio-init-high {
+		pins = "gpio35";
+		output-high;
+	};
+
+	qup_spi11_cs_gpio_init_high: qup-spi11-cs-gpio-init-high {
+		pins = "gpio47";
+		output-high;
+	};
+
+	qup_spi12_cs_gpio_init_high: qup-spi12-cs-gpio-init-high {
+		pins = "gpio51";
+		output-high;
+	};
+
+	qup_uart7_sleep_cts: qup-uart7-sleep-cts {
+		pins = "gpio28";
+		function = "gpio";
+		/*
+		 * Configure a pull-down on CTS to match the pull of
+		 * the Bluetooth module.
+		 */
+		bias-pull-down;
+	};
+
+	qup_uart7_sleep_rts: qup-uart7-sleep-rts {
+		pins = "gpio29";
+		function = "gpio";
+		/*
+		 * Configure pull-down on RTS. As RTS is active low
+		 * signal, pull it low to indicate the BT SoC that it
+		 * can wakeup the system anytime from suspend state by
+		 * pulling RX low (by sending wakeup bytes).
+		 */
+		bias-pull-down;
+	};
+
+	qup_uart7_sleep_rx: qup-uart7-sleep-rx {
+		pins = "gpio31";
+		function = "gpio";
+		/*
+		 * Configure a pull-up on RX. This is needed to avoid
+		 * garbage data when the TX pin of the Bluetooth module
+		 * is floating which may cause spurious wakeups.
+		 */
+		bias-pull-up;
+	};
+
+	qup_uart7_sleep_tx: qup-uart7-sleep-tx {
+		pins = "gpio30";
+		function = "gpio";
+		/*
+		 * Configure pull-up on TX when it isn't actively driven
+		 * to prevent BT SoC from receiving garbage during sleep.
+		 */
+		bias-pull-up;
+	};
+
+	tp_int_odl: tp-int-odl {
+		pins = "gpio102";
+		function = "gpio";
+		/* Has external pullup */
+		bias-disable;
+	};
+
+	ts_int_l: ts-int-l {
+		pins = "gpio81";
+		function = "gpio";
+		/* Has external pullup */
+		bias-pull-up;
+	};
+
+	ts_reset_l: ts-reset-l {
+		pins = "gpio105";
+		function = "gpio";
+		/* Has external pullup */
+		bias-disable;
+		drive-strength = <2>;
+	};
+
+	uf_cam_en: uf-cam-en {
+		pins = "gpio6";
+		function = "gpio";
+		drive-strength = <2>;
+		/* Has external pulldown */
+		bias-disable;
+	};
+
+	wf_cam_en: wf-cam-en {
+		pins = "gpio7";
+		function = "gpio";
+		drive-strength = <2>;
+		/* Has external pulldown */
+		bias-disable;
+	};
+};
diff --git a/arch/arm64/boot/dts/qcom/sc7280-idp.dts b/arch/arm64/boot/dts/qcom/sc7280-idp.dts
index 64fc22aff33d..9b991ba5daaf 100644
--- a/arch/arm64/boot/dts/qcom/sc7280-idp.dts
+++ b/arch/arm64/boot/dts/qcom/sc7280-idp.dts
@@ -61,6 +61,18 @@
 	modem-init;
 };
 
+&pmk8350_rtc {
+	status = "okay";
+};
+
+&nvme_pwren {
+	pins = "gpio19";
+};
+
+&nvme_3v3_regulator {
+	gpio = <&tlmm 19 GPIO_ACTIVE_HIGH>;
+};
+
 &pmk8350_vadc {
 	pmr735a_die_temp {
 		reg = <PMR735A_ADC7_DIE_TEMP>;
diff --git a/arch/arm64/boot/dts/qcom/sc7280-idp.dtsi b/arch/arm64/boot/dts/qcom/sc7280-idp.dtsi
index 371a2a9dcf7a..d623d71d8bd4 100644
--- a/arch/arm64/boot/dts/qcom/sc7280-idp.dtsi
+++ b/arch/arm64/boot/dts/qcom/sc7280-idp.dtsi
@@ -7,11 +7,96 @@
 
 #include <dt-bindings/gpio/gpio.h>
 #include <dt-bindings/iio/qcom,spmi-adc7-pmk8350.h>
+#include <dt-bindings/input/linux-event-codes.h>
 #include "sc7280.dtsi"
 #include "pm7325.dtsi"
 #include "pm8350c.dtsi"
 #include "pmk8350.dtsi"
 
+/ {
+	gpio-keys {
+		compatible = "gpio-keys";
+		label = "gpio-keys";
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&key_vol_up_default>;
+
+		volume-up {
+			label = "volume_up";
+			gpios = <&pm7325_gpios 6 GPIO_ACTIVE_LOW>;
+			linux,input-type = <1>;
+			linux,code = <KEY_VOLUMEUP>;
+			gpio-key,wakeup;
+			debounce-interval = <15>;
+			linux,can-disable;
+		};
+	};
+
+	nvme_3v3_regulator: nvme-3v3-regulator {
+		compatible = "regulator-fixed";
+		regulator-name = "VLDO_3V3";
+
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+
+		enable-active-high;
+		pinctrl-names = "default";
+		pinctrl-0 = <&nvme_pwren>;
+	};
+};
+
+/*
+ * Reserved memory changes
+ *
+ * Delete all unused memory nodes and define the peripheral memory regions
+ * required by the board dts.
+ *
+ */
+
+/delete-node/ &hyp_mem;
+/delete-node/ &xbl_mem;
+/delete-node/ &reserved_xbl_uefi_log;
+/delete-node/ &sec_apps_mem;
+
+/* Increase the size from 2.5MB to 8MB */
+&rmtfs_mem {
+	reg = <0x0 0x9c900000 0x0 0x800000>;
+};
+
+/ {
+	reserved-memory {
+		adsp_mem: memory@86700000 {
+			reg = <0x0 0x86700000 0x0 0x2800000>;
+			no-map;
+		};
+
+		camera_mem: memory@8ad00000 {
+			reg = <0x0 0x8ad00000 0x0 0x500000>;
+			no-map;
+		};
+
+		venus_mem: memory@8b200000 {
+			reg = <0x0 0x8b200000 0x0 0x500000>;
+			no-map;
+		};
+
+		mpss_mem: memory@8b800000 {
+			reg = <0x0 0x8b800000 0x0 0xf600000>;
+			no-map;
+		};
+
+		wpss_mem: memory@9ae00000 {
+			reg = <0x0 0x9ae00000 0x0 0x1900000>;
+			no-map;
+		};
+
+		mba_mem: memory@9c700000 {
+			reg = <0x0 0x9c700000 0x0 0x200000>;
+			no-map;
+		};
+	};
+};
+
 &apps_rsc {
 	pm7325-regulators {
 		compatible = "qcom,pm7325-rpmh-regulators";
@@ -199,6 +284,23 @@
 	modem-init;
 };
 
+&pcie1 {
+	status = "okay";
+	perst-gpio = <&tlmm 2 GPIO_ACTIVE_LOW>;
+
+	vddpe-3v3-supply = <&nvme_3v3_regulator>;
+
+	pinctrl-names = "default";
+	pinctrl-0 = <&pcie1_reset_n>, <&pcie1_wake_n>;
+};
+
+&pcie1_phy {
+	status = "okay";
+
+	vdda-phy-supply = <&vreg_l10c_0p8>;
+	vdda-pll-supply = <&vreg_l6b_1p2>;
+};
+
 &pmk8350_vadc {
 	pmk8350_die_temp {
 		reg = <PMK8350_ADC7_DIE_TEMP>;
@@ -207,10 +309,39 @@
 	};
 };
 
+&qfprom {
+	vcc-supply = <&vreg_l1c_1p8>;
+};
+
+&qspi {
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&qspi_clk>, <&qspi_cs0>, <&qspi_data01>;
+
+	flash@0 {
+		compatible = "jedec,spi-nor";
+		reg = <0>;
+		spi-max-frequency = <37500000>;
+		spi-tx-bus-width = <2>;
+		spi-rx-bus-width = <2>;
+	};
+};
+
 &qupv3_id_0 {
 	status = "okay";
 };
 
+&qupv3_id_1 {
+	status = "okay";
+};
+
+&remoteproc_mpss {
+	status = "okay";
+	compatible = "qcom,sc7280-mss-pil";
+	iommus = <&apps_smmu 0x124 0x0>, <&apps_smmu 0x488 0x7>;
+	memory-region = <&mba_mem &mpss_mem>;
+};
+
 &sdhc_1 {
 	status = "okay";
 
@@ -240,6 +371,7 @@
 };
 
 &uart5 {
+	compatible = "qcom,geni-debug-uart";
 	status = "okay";
 };
 
@@ -282,20 +414,146 @@
 	vdda18-supply = <&vreg_l1c_1p8>;
 };
 
+&uart7 {
+	status = "okay";
+
+	/delete-property/interrupts;
+	interrupts-extended = <&intc GIC_SPI 608 IRQ_TYPE_LEVEL_HIGH>,
+				<&tlmm 31 IRQ_TYPE_EDGE_FALLING>;
+	pinctrl-names = "default", "sleep";
+	pinctrl-1 = <&qup_uart7_sleep_cts>, <&qup_uart7_sleep_rts>, <&qup_uart7_sleep_tx>, <&qup_uart7_sleep_rx>;
+};
+
 /* PINCTRL - additions to nodes defined in sc7280.dtsi */
 
-&qup_uart5_default {
-	tx {
-		pins = "gpio46";
-		drive-strength = <2>;
+&pm7325_gpios {
+	key_vol_up_default: key-vol-up-default {
+		pins = "gpio6";
+		function = "normal";
+		input-enable;
+		bias-pull-up;
+		power-source = <0>;
+		qcom,drive-strength = <3>;
+	};
+};
+
+&qspi_cs0 {
+	bias-disable;
+};
+
+&qspi_clk {
+	bias-disable;
+};
+
+&qspi_data01 {
+	/* High-Z when no transfers; nice to park the lines */
+	bias-pull-up;
+};
+
+&qup_uart5_tx {
+	drive-strength = <2>;
+	bias-disable;
+};
+
+&qup_uart5_rx {
+	drive-strength = <2>;
+	bias-pull-up;
+};
+
+&qup_uart7_cts {
+	/*
+	 * Configure a pull-down on CTS to match the pull of
+	 * the Bluetooth module.
+	 */
+	bias-pull-down;
+};
+
+&qup_uart7_rts {
+	/* We'll drive RTS, so no pull */
+	drive-strength = <2>;
+	bias-disable;
+};
+
+&qup_uart7_tx {
+	/* We'll drive TX, so no pull */
+	drive-strength = <2>;
+	bias-disable;
+};
+
+&qup_uart7_rx {
+	/*
+	 * Configure a pull-up on RX. This is needed to avoid
+	 * garbage data when the TX pin of the Bluetooth module is
+	 * in tri-state (module powered off or not driving the
+	 * signal yet).
+	 */
+	bias-pull-up;
+};
+
+&tlmm {
+	nvme_pwren: nvme-pwren {
+		function = "gpio";
+	};
+
+	pcie1_reset_n: pcie1-reset-n {
+		pins = "gpio2";
+		function = "gpio";
+
+		drive-strength = <16>;
+		output-low;
 		bias-disable;
 	};
 
-	rx {
-		pins = "gpio47";
+	pcie1_wake_n: pcie1-wake-n {
+		pins = "gpio3";
+		function = "gpio";
+
 		drive-strength = <2>;
 		bias-pull-up;
 	};
+
+	qup_uart7_sleep_cts: qup-uart7-sleep-cts {
+		pins = "gpio28";
+		function = "gpio";
+		/*
+		 * Configure a pull-down on CTS to match the pull of
+		 * the Bluetooth module.
+		 */
+		bias-pull-down;
+	};
+
+	qup_uart7_sleep_rts: qup-uart7-sleep-rts {
+		pins = "gpio29";
+		function = "gpio";
+		/*
+		 * Configure pull-down on RTS. As RTS is active low
+		 * signal, pull it low to indicate the BT SoC that it
+		 * can wakeup the system anytime from suspend state by
+		 * pulling RX low (by sending wakeup bytes).
+		 */
+		bias-pull-down;
+	};
+
+	qup_uart7_sleep_tx: qup-uart7-sleep-tx {
+		pins = "gpio30";
+		function = "gpio";
+		/*
+		 * Configure pull-up on TX when it isn't actively driven
+		 * to prevent BT SoC from receiving garbage during sleep.
+		 */
+		bias-pull-up;
+	};
+
+	qup_uart7_sleep_rx: qup-uart7-sleep-rx {
+		pins = "gpio31";
+		function = "gpio";
+		/*
+		 * Configure a pull-up on RX. This is needed to avoid
+		 * garbage data when the TX pin of the Bluetooth module
+		 * is floating which may cause spurious wakeups.
+		 */
+		bias-pull-up;
+	};
 };
 
 &sdc1_on {
@@ -336,6 +594,7 @@
 	};
 
 	sd-cd {
+		pins = "gpio91";
 		bias-pull-up;
 	};
 };
diff --git a/arch/arm64/boot/dts/qcom/sc7280-idp2.dts b/arch/arm64/boot/dts/qcom/sc7280-idp2.dts
index 1fc2addc8ab6..3ae99697d893 100644
--- a/arch/arm64/boot/dts/qcom/sc7280-idp2.dts
+++ b/arch/arm64/boot/dts/qcom/sc7280-idp2.dts
@@ -21,3 +21,11 @@
 		stdout-path = "serial0:115200n8";
 	};
 };
+
+&nvme_pwren {
+	pins = "gpio51";
+};
+
+&nvme_3v3_regulator {
+	gpio = <&tlmm 51 GPIO_ACTIVE_HIGH>;
+};
diff --git a/arch/arm64/boot/dts/qcom/sc7280.dtsi b/arch/arm64/boot/dts/qcom/sc7280.dtsi
index fd78f16181dd..365a2e04e285 100644
--- a/arch/arm64/boot/dts/qcom/sc7280.dtsi
+++ b/arch/arm64/boot/dts/qcom/sc7280.dtsi
@@ -5,12 +5,14 @@
  * Copyright (c) 2020-2021, The Linux Foundation. All rights reserved.
  */
 
+#include <dt-bindings/clock/qcom,dispcc-sc7280.h>
 #include <dt-bindings/clock/qcom,gcc-sc7280.h>
+#include <dt-bindings/clock/qcom,gpucc-sc7280.h>
 #include <dt-bindings/clock/qcom,rpmh.h>
+#include <dt-bindings/clock/qcom,videocc-sc7280.h>
 #include <dt-bindings/interconnect/qcom,sc7280.h>
 #include <dt-bindings/interrupt-controller/arm-gic.h>
 #include <dt-bindings/mailbox/qcom-ipcc.h>
-#include <dt-bindings/power/qcom-aoss-qmp.h>
 #include <dt-bindings/power/qcom-rpmpd.h>
 #include <dt-bindings/reset/qcom,sdm845-aoss.h>
 #include <dt-bindings/reset/qcom,sdm845-pdc.h>
@@ -26,8 +28,40 @@
 	chosen { };
 
 	aliases {
+		i2c0 = &i2c0;
+		i2c1 = &i2c1;
+		i2c2 = &i2c2;
+		i2c3 = &i2c3;
+		i2c4 = &i2c4;
+		i2c5 = &i2c5;
+		i2c6 = &i2c6;
+		i2c7 = &i2c7;
+		i2c8 = &i2c8;
+		i2c9 = &i2c9;
+		i2c10 = &i2c10;
+		i2c11 = &i2c11;
+		i2c12 = &i2c12;
+		i2c13 = &i2c13;
+		i2c14 = &i2c14;
+		i2c15 = &i2c15;
 		mmc1 = &sdhc_1;
 		mmc2 = &sdhc_2;
+		spi0 = &spi0;
+		spi1 = &spi1;
+		spi2 = &spi2;
+		spi3 = &spi3;
+		spi4 = &spi4;
+		spi5 = &spi5;
+		spi6 = &spi6;
+		spi7 = &spi7;
+		spi8 = &spi8;
+		spi9 = &spi9;
+		spi10 = &spi10;
+		spi11 = &spi11;
+		spi12 = &spi12;
+		spi13 = &spi13;
+		spi14 = &spi14;
+		spi15 = &spi15;
 	};
 
 	clocks {
@@ -49,6 +83,16 @@
 		#size-cells = <2>;
 		ranges;
 
+		hyp_mem: memory@80000000 {
+			reg = <0x0 0x80000000 0x0 0x600000>;
+			no-map;
+		};
+
+		xbl_mem: memory@80600000 {
+			reg = <0x0 0x80600000 0x0 0x200000>;
+			no-map;
+		};
+
 		aop_mem: memory@80800000 {
 			reg = <0x0 0x80800000 0x0 0x60000>;
 			no-map;
@@ -60,6 +104,16 @@
 			no-map;
 		};
 
+		reserved_xbl_uefi_log: memory@80880000 {
+			reg = <0x0 0x80884000 0x0 0x10000>;
+			no-map;
+		};
+
+		sec_apps_mem: memory@808ff000 {
+			reg = <0x0 0x808ff000 0x0 0x1000>;
+			no-map;
+		};
+
 		smem_mem: memory@80900000 {
 			reg = <0x0 0x80900000 0x0 0x200000>;
 			no-map;
@@ -70,10 +124,24 @@
 			reg = <0x0 0x80b00000 0x0 0x100000>;
 		};
 
+		wlan_fw_mem: memory@80c00000 {
+			reg = <0x0 0x80c00000 0x0 0xc00000>;
+			no-map;
+		};
+
 		ipa_fw_mem: memory@8b700000 {
 			reg = <0 0x8b700000 0 0x10000>;
 			no-map;
 		};
+
+		rmtfs_mem: memory@9c900000 {
+			compatible = "qcom,rmtfs-mem";
+			reg = <0x0 0x9c900000 0x0 0x280000>;
+			no-map;
+
+			qcom,client-id = <1>;
+			qcom,vmid = <15>;
+		};
 	};
 
 	cpus {
@@ -219,6 +287,42 @@
 			};
 		};
 
+		cpu-map {
+			cluster0 {
+				core0 {
+					cpu = <&CPU0>;
+				};
+
+				core1 {
+					cpu = <&CPU1>;
+				};
+
+				core2 {
+					cpu = <&CPU2>;
+				};
+
+				core3 {
+					cpu = <&CPU3>;
+				};
+
+				core4 {
+					cpu = <&CPU4>;
+				};
+
+				core5 {
+					cpu = <&CPU5>;
+				};
+
+				core6 {
+					cpu = <&CPU6>;
+				};
+
+				core7 {
+					cpu = <&CPU7>;
+				};
+			};
+		};
+
 		idle-states {
 			entry-method = "psci";
 
@@ -415,6 +519,49 @@
 		method = "smc";
 	};
 
+	qspi_opp_table: qspi-opp-table {
+		compatible = "operating-points-v2";
+
+		opp-75000000 {
+			opp-hz = /bits/ 64 <75000000>;
+			required-opps = <&rpmhpd_opp_low_svs>;
+		};
+
+		opp-150000000 {
+			opp-hz = /bits/ 64 <150000000>;
+			required-opps = <&rpmhpd_opp_svs>;
+		};
+
+		opp-200000000 {
+			opp-hz = /bits/ 64 <200000000>;
+			required-opps = <&rpmhpd_opp_svs_l1>;
+		};
+
+		opp-300000000 {
+			opp-hz = /bits/ 64 <300000000>;
+			required-opps = <&rpmhpd_opp_nom>;
+		};
+	};
+
+	qup_opp_table: qup-opp-table {
+		compatible = "operating-points-v2";
+
+		opp-75000000 {
+			opp-hz = /bits/ 64 <75000000>;
+			required-opps = <&rpmhpd_opp_low_svs>;
+		};
+
+		opp-100000000 {
+			opp-hz = /bits/ 64 <100000000>;
+			required-opps = <&rpmhpd_opp_svs>;
+		};
+
+		opp-128000000 {
+			opp-hz = /bits/ 64 <128000000>;
+			required-opps = <&rpmhpd_opp_nom>;
+		};
+	};
+
 	soc: soc@0 {
 		#address-cells = <2>;
 		#size-cells = <2>;
@@ -517,22 +664,857 @@
 		qupv3_id_0: geniqup@9c0000 {
 			compatible = "qcom,geni-se-qup";
 			reg = <0 0x009c0000 0 0x2000>;
-			clock-names = "m-ahb", "s-ahb";
 			clocks = <&gcc GCC_QUPV3_WRAP_0_M_AHB_CLK>,
 				 <&gcc GCC_QUPV3_WRAP_0_S_AHB_CLK>;
+			clock-names = "m-ahb", "s-ahb";
 			#address-cells = <2>;
 			#size-cells = <2>;
 			ranges;
+			iommus = <&apps_smmu 0x123 0x0>;
 			status = "disabled";
 
-			uart5: serial@994000 {
-				compatible = "qcom,geni-debug-uart";
+			i2c0: i2c@980000 {
+				compatible = "qcom,geni-i2c";
+				reg = <0 0x00980000 0 0x4000>;
+				clocks = <&gcc GCC_QUPV3_WRAP0_S0_CLK>;
+				clock-names = "se";
+				pinctrl-names = "default";
+				pinctrl-0 = <&qup_i2c0_data_clk>;
+				interrupts = <GIC_SPI 601 IRQ_TYPE_LEVEL_HIGH>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+				interconnects = <&clk_virt MASTER_QUP_CORE_0 0 &clk_virt SLAVE_QUP_CORE_0 0>,
+						<&gem_noc MASTER_APPSS_PROC 0 &cnoc2 SLAVE_QUP_0 0>,
+						<&aggre1_noc MASTER_QUP_0 0 &mc_virt SLAVE_EBI1 0>;
+				interconnect-names = "qup-core", "qup-config",
+							"qup-memory";
+				status = "disabled";
+			};
+
+			spi0: spi@980000 {
+				compatible = "qcom,geni-spi";
+				reg = <0 0x00980000 0 0x4000>;
+				clocks = <&gcc GCC_QUPV3_WRAP0_S0_CLK>;
+				clock-names = "se";
+				pinctrl-names = "default";
+				pinctrl-0 = <&qup_spi0_data_clk>, <&qup_spi0_cs>;
+				interrupts = <GIC_SPI 601 IRQ_TYPE_LEVEL_HIGH>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+				power-domains = <&rpmhpd SC7280_CX>;
+				operating-points-v2 = <&qup_opp_table>;
+				interconnects = <&clk_virt MASTER_QUP_CORE_0 0 &clk_virt SLAVE_QUP_CORE_0 0>,
+						<&gem_noc MASTER_APPSS_PROC 0 &cnoc2 SLAVE_QUP_0 0>;
+				interconnect-names = "qup-core", "qup-config";
+				status = "disabled";
+			};
+
+			uart0: serial@980000 {
+				compatible = "qcom,geni-uart";
+				reg = <0 0x00980000 0 0x4000>;
+				clocks = <&gcc GCC_QUPV3_WRAP0_S0_CLK>;
+				clock-names = "se";
+				pinctrl-names = "default";
+				pinctrl-0 = <&qup_uart0_cts>, <&qup_uart0_rts>, <&qup_uart0_tx>, <&qup_uart0_rx>;
+				interrupts = <GIC_SPI 601 IRQ_TYPE_LEVEL_HIGH>;
+				power-domains = <&rpmhpd SC7280_CX>;
+				operating-points-v2 = <&qup_opp_table>;
+				interconnects = <&clk_virt MASTER_QUP_CORE_0 0 &clk_virt SLAVE_QUP_CORE_0 0>,
+						<&gem_noc MASTER_APPSS_PROC 0 &cnoc2 SLAVE_QUP_0 0>;
+				interconnect-names = "qup-core", "qup-config";
+				status = "disabled";
+			};
+
+			i2c1: i2c@984000 {
+				compatible = "qcom,geni-i2c";
+				reg = <0 0x00984000 0 0x4000>;
+				clocks = <&gcc GCC_QUPV3_WRAP0_S1_CLK>;
+				clock-names = "se";
+				pinctrl-names = "default";
+				pinctrl-0 = <&qup_i2c1_data_clk>;
+				interrupts = <GIC_SPI 602 IRQ_TYPE_LEVEL_HIGH>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+				interconnects = <&clk_virt MASTER_QUP_CORE_0 0 &clk_virt SLAVE_QUP_CORE_0 0>,
+						<&gem_noc MASTER_APPSS_PROC 0 &cnoc2 SLAVE_QUP_0 0>,
+						<&aggre1_noc MASTER_QUP_0 0 &mc_virt SLAVE_EBI1 0>;
+				interconnect-names = "qup-core", "qup-config",
+							"qup-memory";
+				status = "disabled";
+			};
+
+			spi1: spi@984000 {
+				compatible = "qcom,geni-spi";
+				reg = <0 0x00984000 0 0x4000>;
+				clocks = <&gcc GCC_QUPV3_WRAP0_S1_CLK>;
+				clock-names = "se";
+				pinctrl-names = "default";
+				pinctrl-0 = <&qup_spi1_data_clk>, <&qup_spi1_cs>;
+				interrupts = <GIC_SPI 602 IRQ_TYPE_LEVEL_HIGH>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+				power-domains = <&rpmhpd SC7280_CX>;
+				operating-points-v2 = <&qup_opp_table>;
+				interconnects = <&clk_virt MASTER_QUP_CORE_0 0 &clk_virt SLAVE_QUP_CORE_0 0>,
+						<&gem_noc MASTER_APPSS_PROC 0 &cnoc2 SLAVE_QUP_0 0>;
+				interconnect-names = "qup-core", "qup-config";
+				status = "disabled";
+			};
+
+			uart1: serial@984000 {
+				compatible = "qcom,geni-uart";
+				reg = <0 0x00984000 0 0x4000>;
+				clocks = <&gcc GCC_QUPV3_WRAP0_S1_CLK>;
+				clock-names = "se";
+				pinctrl-names = "default";
+				pinctrl-0 = <&qup_uart1_cts>, <&qup_uart1_rts>, <&qup_uart1_tx>, <&qup_uart1_rx>;
+				interrupts = <GIC_SPI 602 IRQ_TYPE_LEVEL_HIGH>;
+				power-domains = <&rpmhpd SC7280_CX>;
+				operating-points-v2 = <&qup_opp_table>;
+				interconnects = <&clk_virt MASTER_QUP_CORE_0 0 &clk_virt SLAVE_QUP_CORE_0 0>,
+						<&gem_noc MASTER_APPSS_PROC 0 &cnoc2 SLAVE_QUP_0 0>;
+				interconnect-names = "qup-core", "qup-config";
+				status = "disabled";
+			};
+
+			i2c2: i2c@988000 {
+				compatible = "qcom,geni-i2c";
+				reg = <0 0x00988000 0 0x4000>;
+				clocks = <&gcc GCC_QUPV3_WRAP0_S2_CLK>;
+				clock-names = "se";
+				pinctrl-names = "default";
+				pinctrl-0 = <&qup_i2c2_data_clk>;
+				interrupts = <GIC_SPI 603 IRQ_TYPE_LEVEL_HIGH>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+				interconnects = <&clk_virt MASTER_QUP_CORE_0 0 &clk_virt SLAVE_QUP_CORE_0 0>,
+						<&gem_noc MASTER_APPSS_PROC 0 &cnoc2 SLAVE_QUP_0 0>,
+						<&aggre1_noc MASTER_QUP_0 0 &mc_virt SLAVE_EBI1 0>;
+				interconnect-names = "qup-core", "qup-config",
+							"qup-memory";
+				status = "disabled";
+			};
+
+			spi2: spi@988000 {
+				compatible = "qcom,geni-spi";
+				reg = <0 0x00988000 0 0x4000>;
+				clocks = <&gcc GCC_QUPV3_WRAP0_S2_CLK>;
+				clock-names = "se";
+				pinctrl-names = "default";
+				pinctrl-0 = <&qup_spi2_data_clk>, <&qup_spi2_cs>;
+				interrupts = <GIC_SPI 603 IRQ_TYPE_LEVEL_HIGH>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+				power-domains = <&rpmhpd SC7280_CX>;
+				operating-points-v2 = <&qup_opp_table>;
+				interconnects = <&clk_virt MASTER_QUP_CORE_0 0 &clk_virt SLAVE_QUP_CORE_0 0>,
+						<&gem_noc MASTER_APPSS_PROC 0 &cnoc2 SLAVE_QUP_0 0>;
+				interconnect-names = "qup-core", "qup-config";
+				status = "disabled";
+			};
+
+			uart2: serial@988000 {
+				compatible = "qcom,geni-uart";
+				reg = <0 0x00988000 0 0x4000>;
+				clocks = <&gcc GCC_QUPV3_WRAP0_S2_CLK>;
+				clock-names = "se";
+				pinctrl-names = "default";
+				pinctrl-0 = <&qup_uart2_cts>, <&qup_uart2_rts>, <&qup_uart2_tx>, <&qup_uart2_rx>;
+				interrupts = <GIC_SPI 603 IRQ_TYPE_LEVEL_HIGH>;
+				power-domains = <&rpmhpd SC7280_CX>;
+				operating-points-v2 = <&qup_opp_table>;
+				interconnects = <&clk_virt MASTER_QUP_CORE_0 0 &clk_virt SLAVE_QUP_CORE_0 0>,
+						<&gem_noc MASTER_APPSS_PROC 0 &cnoc2 SLAVE_QUP_0 0>;
+				interconnect-names = "qup-core", "qup-config";
+				status = "disabled";
+			};
+
+			i2c3: i2c@98c000 {
+				compatible = "qcom,geni-i2c";
+				reg = <0 0x0098c000 0 0x4000>;
+				clocks = <&gcc GCC_QUPV3_WRAP0_S3_CLK>;
+				clock-names = "se";
+				pinctrl-names = "default";
+				pinctrl-0 = <&qup_i2c3_data_clk>;
+				interrupts = <GIC_SPI 604 IRQ_TYPE_LEVEL_HIGH>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+				interconnects = <&clk_virt MASTER_QUP_CORE_0 0 &clk_virt SLAVE_QUP_CORE_0 0>,
+						<&gem_noc MASTER_APPSS_PROC 0 &cnoc2 SLAVE_QUP_0 0>,
+						<&aggre1_noc MASTER_QUP_0 0 &mc_virt SLAVE_EBI1 0>;
+				interconnect-names = "qup-core", "qup-config",
+							"qup-memory";
+				status = "disabled";
+			};
+
+			spi3: spi@98c000 {
+				compatible = "qcom,geni-spi";
+				reg = <0 0x0098c000 0 0x4000>;
+				clocks = <&gcc GCC_QUPV3_WRAP0_S3_CLK>;
+				clock-names = "se";
+				pinctrl-names = "default";
+				pinctrl-0 = <&qup_spi3_data_clk>, <&qup_spi3_cs>;
+				interrupts = <GIC_SPI 604 IRQ_TYPE_LEVEL_HIGH>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+				power-domains = <&rpmhpd SC7280_CX>;
+				operating-points-v2 = <&qup_opp_table>;
+				interconnects = <&clk_virt MASTER_QUP_CORE_0 0 &clk_virt SLAVE_QUP_CORE_0 0>,
+						<&gem_noc MASTER_APPSS_PROC 0 &cnoc2 SLAVE_QUP_0 0>;
+				interconnect-names = "qup-core", "qup-config";
+				status = "disabled";
+			};
+
+			uart3: serial@98c000 {
+				compatible = "qcom,geni-uart";
+				reg = <0 0x0098c000 0 0x4000>;
+				clocks = <&gcc GCC_QUPV3_WRAP0_S3_CLK>;
+				clock-names = "se";
+				pinctrl-names = "default";
+				pinctrl-0 = <&qup_uart3_cts>, <&qup_uart3_rts>, <&qup_uart3_tx>, <&qup_uart3_rx>;
+				interrupts = <GIC_SPI 604 IRQ_TYPE_LEVEL_HIGH>;
+				power-domains = <&rpmhpd SC7280_CX>;
+				operating-points-v2 = <&qup_opp_table>;
+				interconnects = <&clk_virt MASTER_QUP_CORE_0 0 &clk_virt SLAVE_QUP_CORE_0 0>,
+						<&gem_noc MASTER_APPSS_PROC 0 &cnoc2 SLAVE_QUP_0 0>;
+				interconnect-names = "qup-core", "qup-config";
+				status = "disabled";
+			};
+
+			i2c4: i2c@990000 {
+				compatible = "qcom,geni-i2c";
+				reg = <0 0x00990000 0 0x4000>;
+				clocks = <&gcc GCC_QUPV3_WRAP0_S4_CLK>;
+				clock-names = "se";
+				pinctrl-names = "default";
+				pinctrl-0 = <&qup_i2c4_data_clk>;
+				interrupts = <GIC_SPI 605 IRQ_TYPE_LEVEL_HIGH>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+				interconnects = <&clk_virt MASTER_QUP_CORE_0 0 &clk_virt SLAVE_QUP_CORE_0 0>,
+						<&gem_noc MASTER_APPSS_PROC 0 &cnoc2 SLAVE_QUP_0 0>,
+						<&aggre1_noc MASTER_QUP_0 0 &mc_virt SLAVE_EBI1 0>;
+				interconnect-names = "qup-core", "qup-config",
+							"qup-memory";
+				status = "disabled";
+			};
+
+			spi4: spi@990000 {
+				compatible = "qcom,geni-spi";
+				reg = <0 0x00990000 0 0x4000>;
+				clocks = <&gcc GCC_QUPV3_WRAP0_S4_CLK>;
+				clock-names = "se";
+				pinctrl-names = "default";
+				pinctrl-0 = <&qup_spi4_data_clk>, <&qup_spi4_cs>;
+				interrupts = <GIC_SPI 605 IRQ_TYPE_LEVEL_HIGH>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+				power-domains = <&rpmhpd SC7280_CX>;
+				operating-points-v2 = <&qup_opp_table>;
+				interconnects = <&clk_virt MASTER_QUP_CORE_0 0 &clk_virt SLAVE_QUP_CORE_0 0>,
+						<&gem_noc MASTER_APPSS_PROC 0 &cnoc2 SLAVE_QUP_0 0>;
+				interconnect-names = "qup-core", "qup-config";
+				status = "disabled";
+			};
+
+			uart4: serial@990000 {
+				compatible = "qcom,geni-uart";
+				reg = <0 0x00990000 0 0x4000>;
+				clocks = <&gcc GCC_QUPV3_WRAP0_S4_CLK>;
+				clock-names = "se";
+				pinctrl-names = "default";
+				pinctrl-0 = <&qup_uart4_cts>, <&qup_uart4_rts>, <&qup_uart4_tx>, <&qup_uart4_rx>;
+				interrupts = <GIC_SPI 605 IRQ_TYPE_LEVEL_HIGH>;
+				power-domains = <&rpmhpd SC7280_CX>;
+				operating-points-v2 = <&qup_opp_table>;
+				interconnects = <&clk_virt MASTER_QUP_CORE_0 0 &clk_virt SLAVE_QUP_CORE_0 0>,
+						<&gem_noc MASTER_APPSS_PROC 0 &cnoc2 SLAVE_QUP_0 0>;
+				interconnect-names = "qup-core", "qup-config";
+				status = "disabled";
+			};
+
+			i2c5: i2c@994000 {
+				compatible = "qcom,geni-i2c";
 				reg = <0 0x00994000 0 0x4000>;
+				clocks = <&gcc GCC_QUPV3_WRAP0_S5_CLK>;
 				clock-names = "se";
+				pinctrl-names = "default";
+				pinctrl-0 = <&qup_i2c5_data_clk>;
+				interrupts = <GIC_SPI 606 IRQ_TYPE_LEVEL_HIGH>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+				interconnects = <&clk_virt MASTER_QUP_CORE_0 0 &clk_virt SLAVE_QUP_CORE_0 0>,
+						<&gem_noc MASTER_APPSS_PROC 0 &cnoc2 SLAVE_QUP_0 0>,
+						<&aggre1_noc MASTER_QUP_0 0 &mc_virt SLAVE_EBI1 0>;
+				interconnect-names = "qup-core", "qup-config",
+							"qup-memory";
+				status = "disabled";
+			};
+
+			spi5: spi@994000 {
+				compatible = "qcom,geni-spi";
+				reg = <0 0x00994000 0 0x4000>;
 				clocks = <&gcc GCC_QUPV3_WRAP0_S5_CLK>;
+				clock-names = "se";
 				pinctrl-names = "default";
-				pinctrl-0 = <&qup_uart5_default>;
+				pinctrl-0 = <&qup_spi5_data_clk>, <&qup_spi5_cs>;
 				interrupts = <GIC_SPI 606 IRQ_TYPE_LEVEL_HIGH>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+				power-domains = <&rpmhpd SC7280_CX>;
+				operating-points-v2 = <&qup_opp_table>;
+				interconnects = <&clk_virt MASTER_QUP_CORE_0 0 &clk_virt SLAVE_QUP_CORE_0 0>,
+						<&gem_noc MASTER_APPSS_PROC 0 &cnoc2 SLAVE_QUP_0 0>;
+				interconnect-names = "qup-core", "qup-config";
+				status = "disabled";
+			};
+
+			uart5: serial@994000 {
+				compatible = "qcom,geni-uart";
+				reg = <0 0x00994000 0 0x4000>;
+				clocks = <&gcc GCC_QUPV3_WRAP0_S5_CLK>;
+				clock-names = "se";
+				pinctrl-names = "default";
+				pinctrl-0 = <&qup_uart5_cts>, <&qup_uart5_rts>, <&qup_uart5_tx>, <&qup_uart5_rx>;
+				interrupts = <GIC_SPI 606 IRQ_TYPE_LEVEL_HIGH>;
+				power-domains = <&rpmhpd SC7280_CX>;
+				operating-points-v2 = <&qup_opp_table>;
+				interconnects = <&clk_virt MASTER_QUP_CORE_0 0 &clk_virt SLAVE_QUP_CORE_0 0>,
+						<&gem_noc MASTER_APPSS_PROC 0 &cnoc2 SLAVE_QUP_0 0>;
+				interconnect-names = "qup-core", "qup-config";
+				status = "disabled";
+			};
+
+			i2c6: i2c@998000 {
+				compatible = "qcom,geni-i2c";
+				reg = <0 0x00998000 0 0x4000>;
+				clocks = <&gcc GCC_QUPV3_WRAP0_S6_CLK>;
+				clock-names = "se";
+				pinctrl-names = "default";
+				pinctrl-0 = <&qup_i2c6_data_clk>;
+				interrupts = <GIC_SPI 607 IRQ_TYPE_LEVEL_HIGH>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+				interconnects = <&clk_virt MASTER_QUP_CORE_0 0 &clk_virt SLAVE_QUP_CORE_0 0>,
+						<&gem_noc MASTER_APPSS_PROC 0 &cnoc2 SLAVE_QUP_0 0>,
+						<&aggre1_noc MASTER_QUP_0 0 &mc_virt SLAVE_EBI1 0>;
+				interconnect-names = "qup-core", "qup-config",
+							"qup-memory";
+				status = "disabled";
+			};
+
+			spi6: spi@998000 {
+				compatible = "qcom,geni-spi";
+				reg = <0 0x00998000 0 0x4000>;
+				clocks = <&gcc GCC_QUPV3_WRAP0_S6_CLK>;
+				clock-names = "se";
+				pinctrl-names = "default";
+				pinctrl-0 = <&qup_spi6_data_clk>, <&qup_spi6_cs>;
+				interrupts = <GIC_SPI 607 IRQ_TYPE_LEVEL_HIGH>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+				power-domains = <&rpmhpd SC7280_CX>;
+				operating-points-v2 = <&qup_opp_table>;
+				interconnects = <&clk_virt MASTER_QUP_CORE_0 0 &clk_virt SLAVE_QUP_CORE_0 0>,
+						<&gem_noc MASTER_APPSS_PROC 0 &cnoc2 SLAVE_QUP_0 0>;
+				interconnect-names = "qup-core", "qup-config";
+				status = "disabled";
+			};
+
+			uart6: serial@998000 {
+				compatible = "qcom,geni-uart";
+				reg = <0 0x00998000 0 0x4000>;
+				clocks = <&gcc GCC_QUPV3_WRAP0_S6_CLK>;
+				clock-names = "se";
+				pinctrl-names = "default";
+				pinctrl-0 = <&qup_uart6_cts>, <&qup_uart6_rts>, <&qup_uart6_tx>, <&qup_uart6_rx>;
+				interrupts = <GIC_SPI 607 IRQ_TYPE_LEVEL_HIGH>;
+				power-domains = <&rpmhpd SC7280_CX>;
+				operating-points-v2 = <&qup_opp_table>;
+				interconnects = <&clk_virt MASTER_QUP_CORE_0 0 &clk_virt SLAVE_QUP_CORE_0 0>,
+						<&gem_noc MASTER_APPSS_PROC 0 &cnoc2 SLAVE_QUP_0 0>;
+				interconnect-names = "qup-core", "qup-config";
+				status = "disabled";
+			};
+
+			i2c7: i2c@99c000 {
+				compatible = "qcom,geni-i2c";
+				reg = <0 0x0099c000 0 0x4000>;
+				clocks = <&gcc GCC_QUPV3_WRAP0_S7_CLK>;
+				clock-names = "se";
+				pinctrl-names = "default";
+				pinctrl-0 = <&qup_i2c7_data_clk>;
+				interrupts = <GIC_SPI 608 IRQ_TYPE_LEVEL_HIGH>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+				interconnects = <&clk_virt MASTER_QUP_CORE_0 0 &clk_virt SLAVE_QUP_CORE_0 0>,
+						<&gem_noc MASTER_APPSS_PROC 0 &cnoc2 SLAVE_QUP_0 0>,
+						<&aggre1_noc MASTER_QUP_0 0 &mc_virt SLAVE_EBI1 0>;
+				interconnect-names = "qup-core", "qup-config",
+							"qup-memory";
+				status = "disabled";
+			};
+
+			spi7: spi@99c000 {
+				compatible = "qcom,geni-spi";
+				reg = <0 0x0099c000 0 0x4000>;
+				clocks = <&gcc GCC_QUPV3_WRAP0_S7_CLK>;
+				clock-names = "se";
+				pinctrl-names = "default";
+				pinctrl-0 = <&qup_spi7_data_clk>, <&qup_spi7_cs>;
+				interrupts = <GIC_SPI 608 IRQ_TYPE_LEVEL_HIGH>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+				power-domains = <&rpmhpd SC7280_CX>;
+				operating-points-v2 = <&qup_opp_table>;
+				interconnects = <&clk_virt MASTER_QUP_CORE_0 0 &clk_virt SLAVE_QUP_CORE_0 0>,
+						<&gem_noc MASTER_APPSS_PROC 0 &cnoc2 SLAVE_QUP_0 0>;
+				interconnect-names = "qup-core", "qup-config";
+				status = "disabled";
+			};
+
+			uart7: serial@99c000 {
+				compatible = "qcom,geni-uart";
+				reg = <0 0x0099c000 0 0x4000>;
+				clocks = <&gcc GCC_QUPV3_WRAP0_S7_CLK>;
+				clock-names = "se";
+				pinctrl-names = "default";
+				pinctrl-0 = <&qup_uart7_cts>, <&qup_uart7_rts>, <&qup_uart7_tx>, <&qup_uart7_rx>;
+				interrupts = <GIC_SPI 608 IRQ_TYPE_LEVEL_HIGH>;
+				power-domains = <&rpmhpd SC7280_CX>;
+				operating-points-v2 = <&qup_opp_table>;
+				interconnects = <&clk_virt MASTER_QUP_CORE_0 0 &clk_virt SLAVE_QUP_CORE_0 0>,
+						<&gem_noc MASTER_APPSS_PROC 0 &cnoc2 SLAVE_QUP_0 0>;
+				interconnect-names = "qup-core", "qup-config";
+				status = "disabled";
+			};
+		};
+
+		qupv3_id_1: geniqup@ac0000 {
+			compatible = "qcom,geni-se-qup";
+			reg = <0 0x00ac0000 0 0x2000>;
+			clocks = <&gcc GCC_QUPV3_WRAP_1_M_AHB_CLK>,
+				 <&gcc GCC_QUPV3_WRAP_1_S_AHB_CLK>;
+			clock-names = "m-ahb", "s-ahb";
+			#address-cells = <2>;
+			#size-cells = <2>;
+			ranges;
+			iommus = <&apps_smmu 0x43 0x0>;
+			status = "disabled";
+
+			i2c8: i2c@a80000 {
+				compatible = "qcom,geni-i2c";
+				reg = <0 0x00a80000 0 0x4000>;
+				clocks = <&gcc GCC_QUPV3_WRAP1_S0_CLK>;
+				clock-names = "se";
+				pinctrl-names = "default";
+				pinctrl-0 = <&qup_i2c8_data_clk>;
+				interrupts = <GIC_SPI 353 IRQ_TYPE_LEVEL_HIGH>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+				interconnects = <&clk_virt MASTER_QUP_CORE_1 0 &clk_virt SLAVE_QUP_CORE_1 0>,
+						<&gem_noc MASTER_APPSS_PROC 0 &cnoc2 SLAVE_QUP_1 0>,
+						<&aggre2_noc MASTER_QUP_1 0 &mc_virt SLAVE_EBI1 0>;
+				interconnect-names = "qup-core", "qup-config",
+							"qup-memory";
+				status = "disabled";
+			};
+
+			spi8: spi@a80000 {
+				compatible = "qcom,geni-spi";
+				reg = <0 0x00a80000 0 0x4000>;
+				clocks = <&gcc GCC_QUPV3_WRAP1_S0_CLK>;
+				clock-names = "se";
+				pinctrl-names = "default";
+				pinctrl-0 = <&qup_spi8_data_clk>, <&qup_spi8_cs>;
+				interrupts = <GIC_SPI 353 IRQ_TYPE_LEVEL_HIGH>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+				power-domains = <&rpmhpd SC7280_CX>;
+				operating-points-v2 = <&qup_opp_table>;
+				interconnects = <&clk_virt MASTER_QUP_CORE_1 0 &clk_virt SLAVE_QUP_CORE_1 0>,
+						<&gem_noc MASTER_APPSS_PROC 0 &cnoc2 SLAVE_QUP_1 0>;
+				interconnect-names = "qup-core", "qup-config";
+				status = "disabled";
+			};
+
+			uart8: serial@a80000 {
+				compatible = "qcom,geni-uart";
+				reg = <0 0x00a80000 0 0x4000>;
+				clocks = <&gcc GCC_QUPV3_WRAP1_S0_CLK>;
+				clock-names = "se";
+				pinctrl-names = "default";
+				pinctrl-0 = <&qup_uart8_cts>, <&qup_uart8_rts>, <&qup_uart8_tx>, <&qup_uart8_rx>;
+				interrupts = <GIC_SPI 353 IRQ_TYPE_LEVEL_HIGH>;
+				power-domains = <&rpmhpd SC7280_CX>;
+				operating-points-v2 = <&qup_opp_table>;
+				interconnects = <&clk_virt MASTER_QUP_CORE_1 0 &clk_virt SLAVE_QUP_CORE_1 0>,
+						<&gem_noc MASTER_APPSS_PROC 0 &cnoc2 SLAVE_QUP_1 0>;
+				interconnect-names = "qup-core", "qup-config";
+				status = "disabled";
+			};
+
+			i2c9: i2c@a84000 {
+				compatible = "qcom,geni-i2c";
+				reg = <0 0x00a84000 0 0x4000>;
+				clocks = <&gcc GCC_QUPV3_WRAP1_S1_CLK>;
+				clock-names = "se";
+				pinctrl-names = "default";
+				pinctrl-0 = <&qup_i2c9_data_clk>;
+				interrupts = <GIC_SPI 354 IRQ_TYPE_LEVEL_HIGH>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+				interconnects = <&clk_virt MASTER_QUP_CORE_1 0 &clk_virt SLAVE_QUP_CORE_1 0>,
+						<&gem_noc MASTER_APPSS_PROC 0 &cnoc2 SLAVE_QUP_1 0>,
+						<&aggre2_noc MASTER_QUP_1 0 &mc_virt SLAVE_EBI1 0>;
+				interconnect-names = "qup-core", "qup-config",
+							"qup-memory";
+				status = "disabled";
+			};
+
+			spi9: spi@a84000 {
+				compatible = "qcom,geni-spi";
+				reg = <0 0x00a84000 0 0x4000>;
+				clocks = <&gcc GCC_QUPV3_WRAP1_S1_CLK>;
+				clock-names = "se";
+				pinctrl-names = "default";
+				pinctrl-0 = <&qup_spi9_data_clk>, <&qup_spi9_cs>;
+				interrupts = <GIC_SPI 354 IRQ_TYPE_LEVEL_HIGH>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+				power-domains = <&rpmhpd SC7280_CX>;
+				operating-points-v2 = <&qup_opp_table>;
+				interconnects = <&clk_virt MASTER_QUP_CORE_1 0 &clk_virt SLAVE_QUP_CORE_1 0>,
+						<&gem_noc MASTER_APPSS_PROC 0 &cnoc2 SLAVE_QUP_1 0>;
+				interconnect-names = "qup-core", "qup-config";
+				status = "disabled";
+			};
+
+			uart9: serial@a84000 {
+				compatible = "qcom,geni-uart";
+				reg = <0 0x00a84000 0 0x4000>;
+				clocks = <&gcc GCC_QUPV3_WRAP1_S1_CLK>;
+				clock-names = "se";
+				pinctrl-names = "default";
+				pinctrl-0 = <&qup_uart9_cts>, <&qup_uart9_rts>, <&qup_uart9_tx>, <&qup_uart9_rx>;
+				interrupts = <GIC_SPI 354 IRQ_TYPE_LEVEL_HIGH>;
+				power-domains = <&rpmhpd SC7280_CX>;
+				operating-points-v2 = <&qup_opp_table>;
+				interconnects = <&clk_virt MASTER_QUP_CORE_1 0 &clk_virt SLAVE_QUP_CORE_1 0>,
+						<&gem_noc MASTER_APPSS_PROC 0 &cnoc2 SLAVE_QUP_1 0>;
+				interconnect-names = "qup-core", "qup-config";
+				status = "disabled";
+			};
+
+			i2c10: i2c@a88000 {
+				compatible = "qcom,geni-i2c";
+				reg = <0 0x00a88000 0 0x4000>;
+				clocks = <&gcc GCC_QUPV3_WRAP1_S2_CLK>;
+				clock-names = "se";
+				pinctrl-names = "default";
+				pinctrl-0 = <&qup_i2c10_data_clk>;
+				interrupts = <GIC_SPI 355 IRQ_TYPE_LEVEL_HIGH>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+				interconnects = <&clk_virt MASTER_QUP_CORE_1 0 &clk_virt SLAVE_QUP_CORE_1 0>,
+						<&gem_noc MASTER_APPSS_PROC 0 &cnoc2 SLAVE_QUP_1 0>,
+						<&aggre2_noc MASTER_QUP_1 0 &mc_virt SLAVE_EBI1 0>;
+				interconnect-names = "qup-core", "qup-config",
+							"qup-memory";
+				status = "disabled";
+			};
+
+			spi10: spi@a88000 {
+				compatible = "qcom,geni-spi";
+				reg = <0 0x00a88000 0 0x4000>;
+				clocks = <&gcc GCC_QUPV3_WRAP1_S2_CLK>;
+				clock-names = "se";
+				pinctrl-names = "default";
+				pinctrl-0 = <&qup_spi10_data_clk>, <&qup_spi10_cs>;
+				interrupts = <GIC_SPI 355 IRQ_TYPE_LEVEL_HIGH>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+				power-domains = <&rpmhpd SC7280_CX>;
+				operating-points-v2 = <&qup_opp_table>;
+				interconnects = <&clk_virt MASTER_QUP_CORE_1 0 &clk_virt SLAVE_QUP_CORE_1 0>,
+						<&gem_noc MASTER_APPSS_PROC 0 &cnoc2 SLAVE_QUP_1 0>;
+				interconnect-names = "qup-core", "qup-config";
+				status = "disabled";
+			};
+
+			uart10: serial@a88000 {
+				compatible = "qcom,geni-uart";
+				reg = <0 0x00a88000 0 0x4000>;
+				clocks = <&gcc GCC_QUPV3_WRAP1_S2_CLK>;
+				clock-names = "se";
+				pinctrl-names = "default";
+				pinctrl-0 = <&qup_uart10_cts>, <&qup_uart10_rts>, <&qup_uart10_tx>, <&qup_uart10_rx>;
+				interrupts = <GIC_SPI 355 IRQ_TYPE_LEVEL_HIGH>;
+				power-domains = <&rpmhpd SC7280_CX>;
+				operating-points-v2 = <&qup_opp_table>;
+				interconnects = <&clk_virt MASTER_QUP_CORE_1 0 &clk_virt SLAVE_QUP_CORE_1 0>,
+						<&gem_noc MASTER_APPSS_PROC 0 &cnoc2 SLAVE_QUP_1 0>;
+				interconnect-names = "qup-core", "qup-config";
+				status = "disabled";
+			};
+
+			i2c11: i2c@a8c000 {
+				compatible = "qcom,geni-i2c";
+				reg = <0 0x00a8c000 0 0x4000>;
+				clocks = <&gcc GCC_QUPV3_WRAP1_S3_CLK>;
+				clock-names = "se";
+				pinctrl-names = "default";
+				pinctrl-0 = <&qup_i2c11_data_clk>;
+				interrupts = <GIC_SPI 356 IRQ_TYPE_LEVEL_HIGH>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+				interconnects = <&clk_virt MASTER_QUP_CORE_1 0 &clk_virt SLAVE_QUP_CORE_1 0>,
+						<&gem_noc MASTER_APPSS_PROC 0 &cnoc2 SLAVE_QUP_1 0>,
+						<&aggre2_noc MASTER_QUP_1 0 &mc_virt SLAVE_EBI1 0>;
+				interconnect-names = "qup-core", "qup-config",
+							"qup-memory";
+				status = "disabled";
+			};
+
+			spi11: spi@a8c000 {
+				compatible = "qcom,geni-spi";
+				reg = <0 0x00a8c000 0 0x4000>;
+				clocks = <&gcc GCC_QUPV3_WRAP1_S3_CLK>;
+				clock-names = "se";
+				pinctrl-names = "default";
+				pinctrl-0 = <&qup_spi11_data_clk>, <&qup_spi11_cs>;
+				interrupts = <GIC_SPI 356 IRQ_TYPE_LEVEL_HIGH>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+				power-domains = <&rpmhpd SC7280_CX>;
+				operating-points-v2 = <&qup_opp_table>;
+				interconnects = <&clk_virt MASTER_QUP_CORE_1 0 &clk_virt SLAVE_QUP_CORE_1 0>,
+						<&gem_noc MASTER_APPSS_PROC 0 &cnoc2 SLAVE_QUP_1 0>;
+				interconnect-names = "qup-core", "qup-config";
+				status = "disabled";
+			};
+
+			uart11: serial@a8c000 {
+				compatible = "qcom,geni-uart";
+				reg = <0 0x00a8c000 0 0x4000>;
+				clocks = <&gcc GCC_QUPV3_WRAP1_S3_CLK>;
+				clock-names = "se";
+				pinctrl-names = "default";
+				pinctrl-0 = <&qup_uart11_cts>, <&qup_uart11_rts>, <&qup_uart11_tx>, <&qup_uart11_rx>;
+				interrupts = <GIC_SPI 356 IRQ_TYPE_LEVEL_HIGH>;
+				power-domains = <&rpmhpd SC7280_CX>;
+				operating-points-v2 = <&qup_opp_table>;
+				interconnects = <&clk_virt MASTER_QUP_CORE_1 0 &clk_virt SLAVE_QUP_CORE_1 0>,
+						<&gem_noc MASTER_APPSS_PROC 0 &cnoc2 SLAVE_QUP_1 0>;
+				interconnect-names = "qup-core", "qup-config";
+				status = "disabled";
+			};
+
+			i2c12: i2c@a90000 {
+				compatible = "qcom,geni-i2c";
+				reg = <0 0x00a90000 0 0x4000>;
+				clocks = <&gcc GCC_QUPV3_WRAP1_S4_CLK>;
+				clock-names = "se";
+				pinctrl-names = "default";
+				pinctrl-0 = <&qup_i2c12_data_clk>;
+				interrupts = <GIC_SPI 357 IRQ_TYPE_LEVEL_HIGH>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+				interconnects = <&clk_virt MASTER_QUP_CORE_1 0 &clk_virt SLAVE_QUP_CORE_1 0>,
+						<&gem_noc MASTER_APPSS_PROC 0 &cnoc2 SLAVE_QUP_1 0>,
+						<&aggre2_noc MASTER_QUP_1 0 &mc_virt SLAVE_EBI1 0>;
+				interconnect-names = "qup-core", "qup-config",
+							"qup-memory";
+				status = "disabled";
+			};
+
+			spi12: spi@a90000 {
+				compatible = "qcom,geni-spi";
+				reg = <0 0x00a90000 0 0x4000>;
+				clocks = <&gcc GCC_QUPV3_WRAP1_S4_CLK>;
+				clock-names = "se";
+				pinctrl-names = "default";
+				pinctrl-0 = <&qup_spi12_data_clk>, <&qup_spi12_cs>;
+				interrupts = <GIC_SPI 357 IRQ_TYPE_LEVEL_HIGH>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+				power-domains = <&rpmhpd SC7280_CX>;
+				operating-points-v2 = <&qup_opp_table>;
+				interconnects = <&clk_virt MASTER_QUP_CORE_1 0 &clk_virt SLAVE_QUP_CORE_1 0>,
+						<&gem_noc MASTER_APPSS_PROC 0 &cnoc2 SLAVE_QUP_1 0>;
+				interconnect-names = "qup-core", "qup-config";
+				status = "disabled";
+			};
+
+			uart12: serial@a90000 {
+				compatible = "qcom,geni-uart";
+				reg = <0 0x00a90000 0 0x4000>;
+				clocks = <&gcc GCC_QUPV3_WRAP1_S4_CLK>;
+				clock-names = "se";
+				pinctrl-names = "default";
+				pinctrl-0 = <&qup_uart12_cts>, <&qup_uart12_rts>, <&qup_uart12_tx>, <&qup_uart12_rx>;
+				interrupts = <GIC_SPI 357 IRQ_TYPE_LEVEL_HIGH>;
+				power-domains = <&rpmhpd SC7280_CX>;
+				operating-points-v2 = <&qup_opp_table>;
+				interconnects = <&clk_virt MASTER_QUP_CORE_1 0 &clk_virt SLAVE_QUP_CORE_1 0>,
+						<&gem_noc MASTER_APPSS_PROC 0 &cnoc2 SLAVE_QUP_1 0>;
+				interconnect-names = "qup-core", "qup-config";
+				status = "disabled";
+			};
+
+			i2c13: i2c@a94000 {
+				compatible = "qcom,geni-i2c";
+				reg = <0 0x00a94000 0 0x4000>;
+				clocks = <&gcc GCC_QUPV3_WRAP1_S5_CLK>;
+				clock-names = "se";
+				pinctrl-names = "default";
+				pinctrl-0 = <&qup_i2c13_data_clk>;
+				interrupts = <GIC_SPI 358 IRQ_TYPE_LEVEL_HIGH>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+				interconnects = <&clk_virt MASTER_QUP_CORE_1 0 &clk_virt SLAVE_QUP_CORE_1 0>,
+						<&gem_noc MASTER_APPSS_PROC 0 &cnoc2 SLAVE_QUP_1 0>,
+						<&aggre2_noc MASTER_QUP_1 0 &mc_virt SLAVE_EBI1 0>;
+				interconnect-names = "qup-core", "qup-config",
+							"qup-memory";
+				status = "disabled";
+			};
+
+			spi13: spi@a94000 {
+				compatible = "qcom,geni-spi";
+				reg = <0 0x00a94000 0 0x4000>;
+				clocks = <&gcc GCC_QUPV3_WRAP1_S5_CLK>;
+				clock-names = "se";
+				pinctrl-names = "default";
+				pinctrl-0 = <&qup_spi13_data_clk>, <&qup_spi13_cs>;
+				interrupts = <GIC_SPI 358 IRQ_TYPE_LEVEL_HIGH>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+				power-domains = <&rpmhpd SC7280_CX>;
+				operating-points-v2 = <&qup_opp_table>;
+				interconnects = <&clk_virt MASTER_QUP_CORE_1 0 &clk_virt SLAVE_QUP_CORE_1 0>,
+						<&gem_noc MASTER_APPSS_PROC 0 &cnoc2 SLAVE_QUP_1 0>;
+				interconnect-names = "qup-core", "qup-config";
+				status = "disabled";
+			};
+
+			uart13: serial@a94000 {
+				compatible = "qcom,geni-uart";
+				reg = <0 0x00a94000 0 0x4000>;
+				clocks = <&gcc GCC_QUPV3_WRAP1_S5_CLK>;
+				clock-names = "se";
+				pinctrl-names = "default";
+				pinctrl-0 = <&qup_uart13_cts>, <&qup_uart13_rts>, <&qup_uart13_tx>, <&qup_uart13_rx>;
+				interrupts = <GIC_SPI 358 IRQ_TYPE_LEVEL_HIGH>;
+				power-domains = <&rpmhpd SC7280_CX>;
+				operating-points-v2 = <&qup_opp_table>;
+				interconnects = <&clk_virt MASTER_QUP_CORE_1 0 &clk_virt SLAVE_QUP_CORE_1 0>,
+						<&gem_noc MASTER_APPSS_PROC 0 &cnoc2 SLAVE_QUP_1 0>;
+				interconnect-names = "qup-core", "qup-config";
+				status = "disabled";
+			};
+
+			i2c14: i2c@a98000 {
+				compatible = "qcom,geni-i2c";
+				reg = <0 0x00a98000 0 0x4000>;
+				clocks = <&gcc GCC_QUPV3_WRAP1_S6_CLK>;
+				clock-names = "se";
+				pinctrl-names = "default";
+				pinctrl-0 = <&qup_i2c14_data_clk>;
+				interrupts = <GIC_SPI 368 IRQ_TYPE_LEVEL_HIGH>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+				interconnects = <&clk_virt MASTER_QUP_CORE_1 0 &clk_virt SLAVE_QUP_CORE_1 0>,
+						<&gem_noc MASTER_APPSS_PROC 0 &cnoc2 SLAVE_QUP_1 0>,
+						<&aggre2_noc MASTER_QUP_1 0 &mc_virt SLAVE_EBI1 0>;
+				interconnect-names = "qup-core", "qup-config",
+							"qup-memory";
+				status = "disabled";
+			};
+
+			spi14: spi@a98000 {
+				compatible = "qcom,geni-spi";
+				reg = <0 0x00a98000 0 0x4000>;
+				clocks = <&gcc GCC_QUPV3_WRAP1_S6_CLK>;
+				clock-names = "se";
+				pinctrl-names = "default";
+				pinctrl-0 = <&qup_spi14_data_clk>, <&qup_spi14_cs>;
+				interrupts = <GIC_SPI 368 IRQ_TYPE_LEVEL_HIGH>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+				power-domains = <&rpmhpd SC7280_CX>;
+				operating-points-v2 = <&qup_opp_table>;
+				interconnects = <&clk_virt MASTER_QUP_CORE_1 0 &clk_virt SLAVE_QUP_CORE_1 0>,
+						<&gem_noc MASTER_APPSS_PROC 0 &cnoc2 SLAVE_QUP_1 0>;
+				interconnect-names = "qup-core", "qup-config";
+				status = "disabled";
+			};
+
+			uart14: serial@a98000 {
+				compatible = "qcom,geni-uart";
+				reg = <0 0x00a98000 0 0x4000>;
+				clocks = <&gcc GCC_QUPV3_WRAP1_S6_CLK>;
+				clock-names = "se";
+				pinctrl-names = "default";
+				pinctrl-0 = <&qup_uart14_cts>, <&qup_uart14_rts>, <&qup_uart14_tx>, <&qup_uart14_rx>;
+				interrupts = <GIC_SPI 368 IRQ_TYPE_LEVEL_HIGH>;
+				power-domains = <&rpmhpd SC7280_CX>;
+				operating-points-v2 = <&qup_opp_table>;
+				interconnects = <&clk_virt MASTER_QUP_CORE_1 0 &clk_virt SLAVE_QUP_CORE_1 0>,
+						<&gem_noc MASTER_APPSS_PROC 0 &cnoc2 SLAVE_QUP_1 0>;
+				interconnect-names = "qup-core", "qup-config";
+				status = "disabled";
+			};
+
+			i2c15: i2c@a9c000 {
+				compatible = "qcom,geni-i2c";
+				reg = <0 0x00a9c000 0 0x4000>;
+				clocks = <&gcc GCC_QUPV3_WRAP1_S7_CLK>;
+				clock-names = "se";
+				pinctrl-names = "default";
+				pinctrl-0 = <&qup_i2c15_data_clk>;
+				interrupts = <GIC_SPI 369 IRQ_TYPE_LEVEL_HIGH>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+				interconnects = <&clk_virt MASTER_QUP_CORE_1 0 &clk_virt SLAVE_QUP_CORE_1 0>,
+						<&gem_noc MASTER_APPSS_PROC 0 &cnoc2 SLAVE_QUP_1 0>,
+						<&aggre2_noc MASTER_QUP_1 0 &mc_virt SLAVE_EBI1 0>;
+				interconnect-names = "qup-core", "qup-config",
+							"qup-memory";
+				status = "disabled";
+			};
+
+			spi15: spi@a9c000 {
+				compatible = "qcom,geni-spi";
+				reg = <0 0x00a9c000 0 0x4000>;
+				clocks = <&gcc GCC_QUPV3_WRAP1_S7_CLK>;
+				clock-names = "se";
+				pinctrl-names = "default";
+				pinctrl-0 = <&qup_spi15_data_clk>, <&qup_spi15_cs>;
+				interrupts = <GIC_SPI 369 IRQ_TYPE_LEVEL_HIGH>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+				power-domains = <&rpmhpd SC7280_CX>;
+				operating-points-v2 = <&qup_opp_table>;
+				interconnects = <&clk_virt MASTER_QUP_CORE_1 0 &clk_virt SLAVE_QUP_CORE_1 0>,
+						<&gem_noc MASTER_APPSS_PROC 0 &cnoc2 SLAVE_QUP_1 0>;
+				interconnect-names = "qup-core", "qup-config";
+				status = "disabled";
+			};
+
+			uart15: serial@a9c000 {
+				compatible = "qcom,geni-uart";
+				reg = <0 0x00a9c000 0 0x4000>;
+				clocks = <&gcc GCC_QUPV3_WRAP1_S7_CLK>;
+				clock-names = "se";
+				pinctrl-names = "default";
+				pinctrl-0 = <&qup_uart15_cts>, <&qup_uart15_rts>, <&qup_uart15_tx>, <&qup_uart15_rx>;
+				interrupts = <GIC_SPI 369 IRQ_TYPE_LEVEL_HIGH>;
+				power-domains = <&rpmhpd SC7280_CX>;
+				operating-points-v2 = <&qup_opp_table>;
+				interconnects = <&clk_virt MASTER_QUP_CORE_1 0 &clk_virt SLAVE_QUP_CORE_1 0>,
+						<&gem_noc MASTER_APPSS_PROC 0 &cnoc2 SLAVE_QUP_1 0>;
+				interconnect-names = "qup-core", "qup-config";
 				status = "disabled";
 			};
 		};
@@ -586,6 +1568,117 @@
 			qcom,bcm-voters = <&apps_bcm_voter>;
 		};
 
+		pcie1: pci@1c08000 {
+			compatible = "qcom,pcie-sc7280";
+			reg = <0 0x01c08000 0 0x3000>,
+			      <0 0x40000000 0 0xf1d>,
+			      <0 0x40000f20 0 0xa8>,
+			      <0 0x40001000 0 0x1000>,
+			      <0 0x40100000 0 0x100000>;
+
+			reg-names = "parf", "dbi", "elbi", "atu", "config";
+			device_type = "pci";
+			linux,pci-domain = <1>;
+			bus-range = <0x00 0xff>;
+			num-lanes = <2>;
+
+			#address-cells = <3>;
+			#size-cells = <2>;
+
+			ranges = <0x01000000 0x0 0x40200000 0x0 0x40200000 0x0 0x100000>,
+				 <0x02000000 0x0 0x40300000 0x0 0x40300000 0x0 0x1fd00000>;
+
+			interrupts = <GIC_SPI 307 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "msi";
+			#interrupt-cells = <1>;
+			interrupt-map-mask = <0 0 0 0x7>;
+			interrupt-map = <0 0 0 1 &intc 0 434 IRQ_TYPE_LEVEL_HIGH>,
+					<0 0 0 2 &intc 0 435 IRQ_TYPE_LEVEL_HIGH>,
+					<0 0 0 3 &intc 0 438 IRQ_TYPE_LEVEL_HIGH>,
+					<0 0 0 4 &intc 0 439 IRQ_TYPE_LEVEL_HIGH>;
+
+			clocks = <&gcc GCC_PCIE_1_PIPE_CLK>,
+				 <&gcc GCC_PCIE_1_PIPE_CLK_SRC>,
+				 <&pcie1_lane 0>,
+				 <&rpmhcc RPMH_CXO_CLK>,
+				 <&gcc GCC_PCIE_1_AUX_CLK>,
+				 <&gcc GCC_PCIE_1_CFG_AHB_CLK>,
+				 <&gcc GCC_PCIE_1_MSTR_AXI_CLK>,
+				 <&gcc GCC_PCIE_1_SLV_AXI_CLK>,
+				 <&gcc GCC_PCIE_1_SLV_Q2A_AXI_CLK>,
+				 <&gcc GCC_AGGRE_NOC_PCIE_TBU_CLK>,
+				 <&gcc GCC_DDRSS_PCIE_SF_CLK>;
+
+			clock-names = "pipe",
+				      "pipe_mux",
+				      "phy_pipe",
+				      "ref",
+				      "aux",
+				      "cfg",
+				      "bus_master",
+				      "bus_slave",
+				      "slave_q2a",
+				      "tbu",
+				      "ddrss_sf_tbu";
+
+			assigned-clocks = <&gcc GCC_PCIE_1_AUX_CLK>;
+			assigned-clock-rates = <19200000>;
+
+			resets = <&gcc GCC_PCIE_1_BCR>;
+			reset-names = "pci";
+
+			power-domains = <&gcc GCC_PCIE_1_GDSC>;
+
+			phys = <&pcie1_lane>;
+			phy-names = "pciephy";
+
+			pinctrl-names = "default";
+			pinctrl-0 = <&pcie1_clkreq_n>;
+
+			iommus = <&apps_smmu 0x1c80 0x1>;
+
+			iommu-map = <0x0 &apps_smmu 0x1c80 0x1>,
+				    <0x100 &apps_smmu 0x1c81 0x1>;
+
+			status = "disabled";
+		};
+
+		pcie1_phy: phy@1c0e000 {
+			compatible = "qcom,sm8250-qmp-gen3x2-pcie-phy";
+			reg = <0 0x01c0e000 0 0x1c0>;
+			#address-cells = <2>;
+			#size-cells = <2>;
+			ranges;
+			clocks = <&gcc GCC_PCIE_1_AUX_CLK>,
+				 <&gcc GCC_PCIE_1_CFG_AHB_CLK>,
+				 <&gcc GCC_PCIE_CLKREF_EN>,
+				 <&gcc GCC_PCIE1_PHY_RCHNG_CLK>;
+			clock-names = "aux", "cfg_ahb", "ref", "refgen";
+
+			resets = <&gcc GCC_PCIE_1_PHY_BCR>;
+			reset-names = "phy";
+
+			assigned-clocks = <&gcc GCC_PCIE1_PHY_RCHNG_CLK>;
+			assigned-clock-rates = <100000000>;
+
+			status = "disabled";
+
+			pcie1_lane: lanes@1c0e200 {
+				reg = <0 0x01c0e200 0 0x170>,
+				      <0 0x01c0e400 0 0x200>,
+				      <0 0x01c0ea00 0 0x1f0>,
+				      <0 0x01c0e600 0 0x170>,
+				      <0 0x01c0e800 0 0x200>,
+				      <0 0x01c0ee00 0 0xf4>;
+				clocks = <&gcc GCC_PCIE_1_PIPE_CLK>;
+				clock-names = "pipe0";
+
+				#phy-cells = <0>;
+				#clock-cells = <1>;
+				clock-output-names = "pcie_1_pipe_clk";
+			};
+		};
+
 		ipa: ipa@1e40000 {
 			compatible = "qcom,sc7280-ipa";
 
@@ -598,8 +1691,8 @@
 				    "ipa-shared",
 				    "gsi";
 
-			interrupts-extended = <&intc 0 654 IRQ_TYPE_EDGE_RISING>,
-					      <&intc 0 432 IRQ_TYPE_LEVEL_HIGH>,
+			interrupts-extended = <&intc GIC_SPI 654 IRQ_TYPE_EDGE_RISING>,
+					      <&intc GIC_SPI 432 IRQ_TYPE_LEVEL_HIGH>,
 					      <&ipa_smp2p_in 0 IRQ_TYPE_EDGE_RISING>,
 					      <&ipa_smp2p_in 1 IRQ_TYPE_EDGE_RISING>;
 			interrupt-names = "ipa",
@@ -629,6 +1722,11 @@
 			#hwlock-cells = <1>;
 		};
 
+		tcsr: syscon@1fc0000 {
+			compatible = "qcom,sc7280-tcsr", "syscon";
+			reg = <0 0x01fc0000 0 0x30000>;
+		};
+
 		lpasscc: lpasscc@3000000 {
 			compatible = "qcom,sc7280-lpasscc";
 			reg = <0 0x03000000 0 0x40>,
@@ -647,6 +1745,86 @@
 			qcom,bcm-voters = <&apps_bcm_voter>;
 		};
 
+		gpu: gpu@3d00000 {
+			compatible = "qcom,adreno-635.0", "qcom,adreno";
+			#stream-id-cells = <16>;
+			reg = <0 0x03d00000 0 0x40000>,
+			      <0 0x03d9e000 0 0x1000>,
+			      <0 0x03d61000 0 0x800>;
+			reg-names = "kgsl_3d0_reg_memory",
+				    "cx_mem",
+				    "cx_dbgc";
+			interrupts = <GIC_SPI 300 IRQ_TYPE_LEVEL_HIGH>;
+			iommus = <&adreno_smmu 0 0x401>;
+			operating-points-v2 = <&gpu_opp_table>;
+			qcom,gmu = <&gmu>;
+			interconnects = <&gem_noc MASTER_GFX3D 0 &mc_virt SLAVE_EBI1 0>;
+			interconnect-names = "gfx-mem";
+			#cooling-cells = <2>;
+
+			gpu_opp_table: opp-table {
+				compatible = "operating-points-v2";
+
+				opp-315000000 {
+					opp-hz = /bits/ 64 <315000000>;
+					opp-level = <RPMH_REGULATOR_LEVEL_LOW_SVS>;
+					opp-peak-kBps = <1804000>;
+				};
+
+				opp-450000000 {
+					opp-hz = /bits/ 64 <450000000>;
+					opp-level = <RPMH_REGULATOR_LEVEL_SVS>;
+					opp-peak-kBps = <4068000>;
+				};
+
+				opp-550000000 {
+					opp-hz = /bits/ 64 <550000000>;
+					opp-level = <RPMH_REGULATOR_LEVEL_SVS_L1>;
+					opp-peak-kBps = <6832000>;
+				};
+			};
+		};
+
+		gmu: gmu@3d69000 {
+			compatible="qcom,adreno-gmu-635.0", "qcom,adreno-gmu";
+			reg = <0 0x03d6a000 0 0x34000>,
+				<0 0x3de0000 0 0x10000>,
+				<0 0x0b290000 0 0x10000>;
+			reg-names = "gmu", "rscc", "gmu_pdc";
+			interrupts = <GIC_SPI 304 IRQ_TYPE_LEVEL_HIGH>,
+					<GIC_SPI 305 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "hfi", "gmu";
+			clocks = <&gpucc 5>,
+					<&gpucc 8>,
+					<&gcc GCC_DDRSS_GPU_AXI_CLK>,
+					<&gcc GCC_GPU_MEMNOC_GFX_CLK>,
+					<&gpucc 2>,
+					<&gpucc 15>,
+					<&gpucc 11>;
+			clock-names = "gmu",
+				      "cxo",
+				      "axi",
+				      "memnoc",
+				      "ahb",
+				      "hub",
+				      "smmu_vote";
+			power-domains = <&gpucc 0>,
+					<&gpucc 1>;
+			power-domain-names = "cx",
+					     "gx";
+			iommus = <&adreno_smmu 5 0x400>;
+			operating-points-v2 = <&gmu_opp_table>;
+
+			gmu_opp_table: opp-table {
+				compatible = "operating-points-v2";
+
+				opp-200000000 {
+					opp-hz = /bits/ 64 <200000000>;
+					opp-level = <RPMH_REGULATOR_LEVEL_MIN_SVS>;
+				};
+			};
+		};
+
 		gpucc: clock-controller@3d90000 {
 			compatible = "qcom,sc7280-gpucc";
 			reg = <0 0x03d90000 0 0x9000>;
@@ -661,6 +1839,95 @@
 			#power-domain-cells = <1>;
 		};
 
+		adreno_smmu: iommu@3da0000 {
+			compatible = "qcom,sc7280-smmu-500", "qcom,adreno-smmu", "arm,mmu-500";
+			reg = <0 0x03da0000 0 0x20000>;
+			#iommu-cells = <2>;
+			#global-interrupts = <2>;
+			interrupts = <GIC_SPI 673 IRQ_TYPE_LEVEL_HIGH>,
+					<GIC_SPI 675 IRQ_TYPE_LEVEL_HIGH>,
+					<GIC_SPI 678 IRQ_TYPE_LEVEL_HIGH>,
+					<GIC_SPI 679 IRQ_TYPE_LEVEL_HIGH>,
+					<GIC_SPI 680 IRQ_TYPE_LEVEL_HIGH>,
+					<GIC_SPI 681 IRQ_TYPE_LEVEL_HIGH>,
+					<GIC_SPI 682 IRQ_TYPE_LEVEL_HIGH>,
+					<GIC_SPI 683 IRQ_TYPE_LEVEL_HIGH>,
+					<GIC_SPI 684 IRQ_TYPE_LEVEL_HIGH>,
+					<GIC_SPI 685 IRQ_TYPE_LEVEL_HIGH>,
+					<GIC_SPI 686 IRQ_TYPE_LEVEL_HIGH>,
+					<GIC_SPI 687 IRQ_TYPE_LEVEL_HIGH>;
+
+			clocks = <&gcc GCC_GPU_MEMNOC_GFX_CLK>,
+					<&gcc GCC_GPU_SNOC_DVM_GFX_CLK>,
+					<&gpucc 2>,
+					<&gpucc 11>,
+					<&gpucc 5>,
+					<&gpucc 15>,
+					<&gpucc 13>;
+			clock-names = "gcc_gpu_memnoc_gfx_clk",
+					"gcc_gpu_snoc_dvm_gfx_clk",
+					"gpu_cc_ahb_clk",
+					"gpu_cc_hlos1_vote_gpu_smmu_clk",
+					"gpu_cc_cx_gmu_clk",
+					"gpu_cc_hub_cx_int_clk",
+					"gpu_cc_hub_aon_clk";
+
+			power-domains = <&gpucc 0>;
+		};
+
+		remoteproc_mpss: remoteproc@4080000 {
+			compatible = "qcom,sc7280-mpss-pas";
+			reg = <0 0x04080000 0 0x10000>, <0 0x04180000 0 0x48>;
+			reg-names = "qdsp6", "rmb";
+
+			interrupts-extended = <&intc GIC_SPI 264 IRQ_TYPE_EDGE_RISING>,
+					      <&modem_smp2p_in 0 IRQ_TYPE_EDGE_RISING>,
+					      <&modem_smp2p_in 1 IRQ_TYPE_EDGE_RISING>,
+					      <&modem_smp2p_in 2 IRQ_TYPE_EDGE_RISING>,
+					      <&modem_smp2p_in 3 IRQ_TYPE_EDGE_RISING>,
+					      <&modem_smp2p_in 7 IRQ_TYPE_EDGE_RISING>;
+			interrupt-names = "wdog", "fatal", "ready", "handover",
+					  "stop-ack", "shutdown-ack";
+
+			clocks = <&gcc GCC_MSS_CFG_AHB_CLK>,
+				 <&gcc GCC_MSS_OFFLINE_AXI_CLK>,
+				 <&gcc GCC_MSS_SNOC_AXI_CLK>,
+				 <&rpmhcc RPMH_PKA_CLK>,
+				 <&rpmhcc RPMH_CXO_CLK>;
+			clock-names = "iface", "offline", "snoc_axi", "pka", "xo";
+
+			power-domains = <&rpmhpd SC7280_CX>,
+					<&rpmhpd SC7280_MSS>;
+			power-domain-names = "cx", "mss";
+
+			memory-region = <&mpss_mem>;
+
+			qcom,qmp = <&aoss_qmp>;
+
+			qcom,smem-states = <&modem_smp2p_out 0>;
+			qcom,smem-state-names = "stop";
+
+			resets = <&aoss_reset AOSS_CC_MSS_RESTART>,
+				 <&pdc_reset PDC_MODEM_SYNC_RESET>;
+			reset-names = "mss_restart", "pdc_reset";
+
+			qcom,halt-regs = <&tcsr_mutex 0x23000 0x25000 0x28000 0x33000>;
+			qcom,ext-regs = <&tcsr 0x10000 0x10004 &tcsr_mutex 0x26004 0x26008>;
+			qcom,qaccept-regs = <&tcsr_mutex 0x23030 0x23040 0x23020>;
+
+			status = "disabled";
+
+			glink-edge {
+				interrupts-extended = <&ipcc IPCC_CLIENT_MPSS
+							     IPCC_MPROC_SIGNAL_GLINK_QMP
+							     IRQ_TYPE_EDGE_RISING>;
+				mboxes = <&ipcc IPCC_CLIENT_MPSS
+						IPCC_MPROC_SIGNAL_GLINK_QMP>;
+				label = "modem";
+				qcom,remote-pid = <1>;
+			};
+		};
+
 		stm@6002000 {
 			compatible = "arm,coresight-stm", "arm,primecell";
 			reg = <0 0x06002000 0 0x1000>,
@@ -1258,15 +2525,11 @@
 			dp_phy: dp-phy@88ea200 {
 				reg = <0 0x088ea200 0 0x200>,
 				      <0 0x088ea400 0 0x200>,
-				      <0 0x088eac00 0 0x400>,
+				      <0 0x088eaa00 0 0x200>,
 				      <0 0x088ea600 0 0x200>,
-				      <0 0x088ea800 0 0x200>,
-				      <0 0x088eaa00 0 0x100>;
+				      <0 0x088ea800 0 0x200>;
 				#phy-cells = <0>;
 				#clock-cells = <1>;
-				clocks = <&gcc GCC_USB3_PRIM_PHY_PIPE_CLK>;
-				clock-names = "pipe0";
-				clock-output-names = "usb3_phy_pipe_clk_src";
 			};
 		};
 
@@ -1318,6 +2581,23 @@
 			};
 		};
 
+		qspi: spi@88dc000 {
+			compatible = "qcom,sc7280-qspi", "qcom,qspi-v1";
+			reg = <0 0x088dc000 0 0x1000>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			interrupts = <GIC_SPI 82 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&gcc GCC_QSPI_CNOC_PERIPH_AHB_CLK>,
+				 <&gcc GCC_QSPI_CORE_CLK>;
+			clock-names = "iface", "core";
+			interconnects = <&gem_noc MASTER_APPSS_PROC 0
+					&cnoc2 SLAVE_QSPI_0 0>;
+			interconnect-names = "qspi-config";
+			power-domains = <&rpmhpd SC7280_CX>;
+			operating-points-v2 = <&qspi_opp_table>;
+			status = "disabled";
+		};
+
 		dc_noc: interconnect@90e0000 {
 			reg = <0 0x090e0000 0 0x5080>;
 			compatible = "qcom,sc7280-dc-noc";
@@ -1473,7 +2753,7 @@
 
 		aoss_qmp: power-controller@c300000 {
 			compatible = "qcom,sc7280-aoss-qmp";
-			reg = <0 0x0c300000 0 0x100000>;
+			reg = <0 0x0c300000 0 0x400>;
 			interrupts-extended = <&ipcc IPCC_CLIENT_AOP
 						     IPCC_MPROC_SIGNAL_GLINK_QMP
 						     IRQ_TYPE_EDGE_RISING>;
@@ -1481,7 +2761,11 @@
 					IPCC_MPROC_SIGNAL_GLINK_QMP>;
 
 			#clock-cells = <0>;
-			#power-domain-cells = <1>;
+		};
+
+		sram@c3f0000 {
+			compatible = "qcom,rpmh-stats";
+			reg = <0 0x0c3f0000 0 0x400>;
 		};
 
 		spmi_bus: spmi@c440000 {
@@ -1513,11 +2797,518 @@
 			gpio-ranges = <&tlmm 0 0 175>;
 			wakeup-parent = <&pdc>;
 
-			qup_uart5_default: qup-uart5-default {
-				pins = "gpio46", "gpio47";
+			pcie1_clkreq_n: pcie1-clkreq-n {
+				pins = "gpio79";
+				function = "pcie1_clkreqn";
+				drive-strength = <2>;
+				bias-pull-up;
+			};
+
+			qspi_clk: qspi-clk {
+				pins = "gpio14";
+				function = "qspi_clk";
+			};
+
+			qspi_cs0: qspi-cs0 {
+				pins = "gpio15";
+				function = "qspi_cs";
+			};
+
+			qspi_cs1: qspi-cs1 {
+				pins = "gpio19";
+				function = "qspi_cs";
+			};
+
+			qspi_data01: qspi-data01 {
+				pins = "gpio12", "gpio13";
+				function = "qspi_data";
+			};
+
+			qspi_data12: qspi-data12 {
+				pins = "gpio16", "gpio17";
+				function = "qspi_data";
+			};
+
+			qup_i2c0_data_clk: qup-i2c0-data-clk {
+				pins = "gpio0", "gpio1";
+				function = "qup00";
+			};
+
+			qup_i2c1_data_clk: qup-i2c1-data-clk {
+				pins = "gpio4", "gpio5";
+				function = "qup01";
+			};
+
+			qup_i2c2_data_clk: qup-i2c2-data-clk {
+				pins = "gpio8", "gpio9";
+				function = "qup02";
+			};
+
+			qup_i2c3_data_clk: qup-i2c3-data-clk {
+				pins = "gpio12", "gpio13";
+				function = "qup03";
+			};
+
+			qup_i2c4_data_clk: qup-i2c4-data-clk {
+				pins = "gpio16", "gpio17";
+				function = "qup04";
+			};
+
+			qup_i2c5_data_clk: qup-i2c5-data-clk {
+				pins = "gpio20", "gpio21";
+				function = "qup05";
+			};
+
+			qup_i2c6_data_clk: qup-i2c6-data-clk {
+				pins = "gpio24", "gpio25";
+				function = "qup06";
+			};
+
+			qup_i2c7_data_clk: qup-i2c7-data-clk {
+				pins = "gpio28", "gpio29";
+				function = "qup07";
+			};
+
+			qup_i2c8_data_clk: qup-i2c8-data-clk {
+				pins = "gpio32", "gpio33";
+				function = "qup10";
+			};
+
+			qup_i2c9_data_clk: qup-i2c9-data-clk {
+				pins = "gpio36", "gpio37";
+				function = "qup11";
+			};
+
+			qup_i2c10_data_clk: qup-i2c10-data-clk {
+				pins = "gpio40", "gpio41";
+				function = "qup12";
+			};
+
+			qup_i2c11_data_clk: qup-i2c11-data-clk {
+				pins = "gpio44", "gpio45";
+				function = "qup13";
+			};
+
+			qup_i2c12_data_clk: qup-i2c12-data-clk {
+				pins = "gpio48", "gpio49";
+				function = "qup14";
+			};
+
+			qup_i2c13_data_clk: qup-i2c13-data-clk {
+				pins = "gpio52", "gpio53";
+				function = "qup15";
+			};
+
+			qup_i2c14_data_clk: qup-i2c14-data-clk {
+				pins = "gpio56", "gpio57";
+				function = "qup16";
+			};
+
+			qup_i2c15_data_clk: qup-i2c15-data-clk {
+				pins = "gpio60", "gpio61";
+				function = "qup17";
+			};
+
+			qup_spi0_data_clk: qup-spi0-data-clk {
+				pins = "gpio0", "gpio1", "gpio2";
+				function = "qup00";
+			};
+
+			qup_spi0_cs: qup-spi0-cs {
+				pins = "gpio3";
+				function = "qup00";
+			};
+
+			qup_spi0_cs_gpio: qup-spi0-cs-gpio {
+				pins = "gpio3";
+				function = "gpio";
+			};
+
+			qup_spi1_data_clk: qup-spi1-data-clk {
+				pins = "gpio4", "gpio5", "gpio6";
+				function = "qup01";
+			};
+
+			qup_spi1_cs: qup-spi1-cs {
+				pins = "gpio7";
+				function = "qup01";
+			};
+
+			qup_spi1_cs_gpio: qup-spi1-cs-gpio {
+				pins = "gpio7";
+				function = "gpio";
+			};
+
+			qup_spi2_data_clk: qup-spi2-data-clk {
+				pins = "gpio8", "gpio9", "gpio10";
+				function = "qup02";
+			};
+
+			qup_spi2_cs: qup-spi2-cs {
+				pins = "gpio11";
+				function = "qup02";
+			};
+
+			qup_spi2_cs_gpio: qup-spi2-cs-gpio {
+				pins = "gpio11";
+				function = "gpio";
+			};
+
+			qup_spi3_data_clk: qup-spi3-data-clk {
+				pins = "gpio12", "gpio13", "gpio14";
+				function = "qup03";
+			};
+
+			qup_spi3_cs: qup-spi3-cs {
+				pins = "gpio15";
+				function = "qup03";
+			};
+
+			qup_spi3_cs_gpio: qup-spi3-cs-gpio {
+				pins = "gpio15";
+				function = "gpio";
+			};
+
+			qup_spi4_data_clk: qup-spi4-data-clk {
+				pins = "gpio16", "gpio17", "gpio18";
+				function = "qup04";
+			};
+
+			qup_spi4_cs: qup-spi4-cs {
+				pins = "gpio19";
+				function = "qup04";
+			};
+
+			qup_spi4_cs_gpio: qup-spi4-cs-gpio {
+				pins = "gpio19";
+				function = "gpio";
+			};
+
+			qup_spi5_data_clk: qup-spi5-data-clk {
+				pins = "gpio20", "gpio21", "gpio22";
+				function = "qup05";
+			};
+
+			qup_spi5_cs: qup-spi5-cs {
+				pins = "gpio23";
+				function = "qup05";
+			};
+
+			qup_spi5_cs_gpio: qup-spi5-cs-gpio {
+				pins = "gpio23";
+				function = "gpio";
+			};
+
+			qup_spi6_data_clk: qup-spi6-data-clk {
+				pins = "gpio24", "gpio25", "gpio26";
+				function = "qup06";
+			};
+
+			qup_spi6_cs: qup-spi6-cs {
+				pins = "gpio27";
+				function = "qup06";
+			};
+
+			qup_spi6_cs_gpio: qup-spi6-cs-gpio {
+				pins = "gpio27";
+				function = "gpio";
+			};
+
+			qup_spi7_data_clk: qup-spi7-data-clk {
+				pins = "gpio28", "gpio29", "gpio30";
+				function = "qup07";
+			};
+
+			qup_spi7_cs: qup-spi7-cs {
+				pins = "gpio31";
+				function = "qup07";
+			};
+
+			qup_spi7_cs_gpio: qup-spi7-cs-gpio {
+				pins = "gpio31";
+				function = "gpio";
+			};
+
+			qup_spi8_data_clk: qup-spi8-data-clk {
+				pins = "gpio32", "gpio33", "gpio34";
+				function = "qup10";
+			};
+
+			qup_spi8_cs: qup-spi8-cs {
+				pins = "gpio35";
+				function = "qup10";
+			};
+
+			qup_spi8_cs_gpio: qup-spi8-cs-gpio {
+				pins = "gpio35";
+				function = "gpio";
+			};
+
+			qup_spi9_data_clk: qup-spi9-data-clk {
+				pins = "gpio36", "gpio37", "gpio38";
+				function = "qup11";
+			};
+
+			qup_spi9_cs: qup-spi9-cs {
+				pins = "gpio39";
+				function = "qup11";
+			};
+
+			qup_spi9_cs_gpio: qup-spi9-cs-gpio {
+				pins = "gpio39";
+				function = "gpio";
+			};
+
+			qup_spi10_data_clk: qup-spi10-data-clk {
+				pins = "gpio40", "gpio41", "gpio42";
+				function = "qup12";
+			};
+
+			qup_spi10_cs: qup-spi10-cs {
+				pins = "gpio43";
+				function = "qup12";
+			};
+
+			qup_spi10_cs_gpio: qup-spi10-cs-gpio {
+				pins = "gpio43";
+				function = "gpio";
+			};
+
+			qup_spi11_data_clk: qup-spi11-data-clk {
+				pins = "gpio44", "gpio45", "gpio46";
 				function = "qup13";
 			};
 
+			qup_spi11_cs: qup-spi11-cs {
+				pins = "gpio47";
+				function = "qup13";
+			};
+
+			qup_spi11_cs_gpio: qup-spi11-cs-gpio {
+				pins = "gpio47";
+				function = "gpio";
+			};
+
+			qup_spi12_data_clk: qup-spi12-data-clk {
+				pins = "gpio48", "gpio49", "gpio50";
+				function = "qup14";
+			};
+
+			qup_spi12_cs: qup-spi12-cs {
+				pins = "gpio51";
+				function = "qup14";
+			};
+
+			qup_spi12_cs_gpio: qup-spi12-cs-gpio {
+				pins = "gpio51";
+				function = "gpio";
+			};
+
+			qup_spi13_data_clk: qup-spi13-data-clk {
+				pins = "gpio52", "gpio53", "gpio54";
+				function = "qup15";
+			};
+
+			qup_spi13_cs: qup-spi13-cs {
+				pins = "gpio55";
+				function = "qup15";
+			};
+
+			qup_spi13_cs_gpio: qup-spi13-cs-gpio {
+				pins = "gpio55";
+				function = "gpio";
+			};
+
+			qup_spi14_data_clk: qup-spi14-data-clk {
+				pins = "gpio56", "gpio57", "gpio58";
+				function = "qup16";
+			};
+
+			qup_spi14_cs: qup-spi14-cs {
+				pins = "gpio59";
+				function = "qup16";
+			};
+
+			qup_spi14_cs_gpio: qup-spi14-cs-gpio {
+				pins = "gpio59";
+				function = "gpio";
+			};
+
+			qup_spi15_data_clk: qup-spi15-data-clk {
+				pins = "gpio60", "gpio61", "gpio62";
+				function = "qup17";
+			};
+
+			qup_spi15_cs: qup-spi15-cs {
+				pins = "gpio63";
+				function = "qup17";
+			};
+
+			qup_spi15_cs_gpio: qup-spi15-cs-gpio {
+				pins = "gpio63";
+				function = "gpio";
+			};
+
+			qup_uart0_cts: qup-uart0-cts {
+				pins = "gpio0";
+				function = "qup00";
+			};
+
+			qup_uart0_rts: qup-uart0-rts {
+				pins = "gpio1";
+				function = "qup00";
+			};
+
+			qup_uart0_tx: qup-uart0-tx {
+				pins = "gpio2";
+				function = "qup00";
+			};
+
+			qup_uart0_rx: qup-uart0-rx {
+				pins = "gpio3";
+				function = "qup00";
+			};
+
+			qup_uart1_cts: qup-uart1-cts {
+				pins = "gpio4";
+				function = "qup01";
+			};
+
+			qup_uart1_rts: qup-uart1-rts {
+				pins = "gpio5";
+				function = "qup01";
+			};
+
+			qup_uart1_tx: qup-uart1-tx {
+				pins = "gpio6";
+				function = "qup01";
+			};
+
+			qup_uart1_rx: qup-uart1-rx {
+				pins = "gpio7";
+				function = "qup01";
+			};
+
+			qup_uart2_cts: qup-uart2-cts {
+				pins = "gpio8";
+				function = "qup02";
+			};
+
+			qup_uart2_rts: qup-uart2-rts {
+				pins = "gpio9";
+				function = "qup02";
+			};
+
+			qup_uart2_tx: qup-uart2-tx {
+				pins = "gpio10";
+				function = "qup02";
+			};
+
+			qup_uart2_rx: qup-uart2-rx {
+				pins = "gpio11";
+				function = "qup02";
+			};
+
+			qup_uart3_cts: qup-uart3-cts {
+				pins = "gpio12";
+				function = "qup03";
+			};
+
+			qup_uart3_rts: qup-uart3-rts {
+				pins = "gpio13";
+				function = "qup03";
+			};
+
+			qup_uart3_tx: qup-uart3-tx {
+				pins = "gpio14";
+				function = "qup03";
+			};
+
+			qup_uart3_rx: qup-uart3-rx {
+				pins = "gpio15";
+				function = "qup03";
+			};
+
+			qup_uart4_cts: qup-uart4-cts {
+				pins = "gpio16";
+				function = "qup04";
+			};
+
+			qup_uart4_rts: qup-uart4-rts {
+				pins = "gpio17";
+				function = "qup04";
+			};
+
+			qup_uart4_tx: qup-uart4-tx {
+				pins = "gpio18";
+				function = "qup04";
+			};
+
+			qup_uart4_rx: qup-uart4-rx {
+				pins = "gpio19";
+				function = "qup04";
+			};
+
+			qup_uart5_cts: qup-uart5-cts {
+				pins = "gpio20";
+				function = "qup05";
+			};
+
+			qup_uart5_rts: qup-uart5-rts {
+				pins = "gpio21";
+				function = "qup05";
+			};
+
+			qup_uart5_tx: qup-uart5-tx {
+				pins = "gpio22";
+				function = "qup05";
+			};
+
+			qup_uart5_rx: qup-uart5-rx {
+				pins = "gpio23";
+				function = "qup05";
+			};
+
+			qup_uart6_cts: qup-uart6-cts {
+				pins = "gpio24";
+				function = "qup06";
+			};
+
+			qup_uart6_rts: qup-uart6-rts {
+				pins = "gpio25";
+				function = "qup06";
+			};
+
+			qup_uart6_tx: qup-uart6-tx {
+				pins = "gpio26";
+				function = "qup06";
+			};
+
+			qup_uart6_rx: qup-uart6-rx {
+				pins = "gpio27";
+				function = "qup06";
+			};
+
+			qup_uart7_cts: qup-uart7-cts {
+				pins = "gpio28";
+				function = "qup07";
+			};
+
+			qup_uart7_rts: qup-uart7-rts {
+				pins = "gpio29";
+				function = "qup07";
+			};
+
+			qup_uart7_tx: qup-uart7-tx {
+				pins = "gpio30";
+				function = "qup07";
+			};
+
+			qup_uart7_rx: qup-uart7-rx {
+				pins = "gpio31";
+				function = "qup07";
+			};
+
 			sdc1_on: sdc1-on {
 				clk {
 					pins = "sdc1_clk";
@@ -1573,10 +3364,6 @@
 				data {
 					pins = "sdc2_data";
 				};
-
-				sd-cd {
-					pins = "gpio91";
-				};
 			};
 
 			sdc2_off: sdc2-off {
@@ -1598,6 +3385,181 @@
 					bias-bus-hold;
 				};
 			};
+
+			qup_uart8_cts: qup-uart8-cts {
+				pins = "gpio32";
+				function = "qup10";
+			};
+
+			qup_uart8_rts: qup-uart8-rts {
+				pins = "gpio33";
+				function = "qup10";
+			};
+
+			qup_uart8_tx: qup-uart8-tx {
+				pins = "gpio34";
+				function = "qup10";
+			};
+
+			qup_uart8_rx: qup-uart8-rx {
+				pins = "gpio35";
+				function = "qup10";
+			};
+
+			qup_uart9_cts: qup-uart9-cts {
+				pins = "gpio36";
+				function = "qup11";
+			};
+
+			qup_uart9_rts: qup-uart9-rts {
+				pins = "gpio37";
+				function = "qup11";
+			};
+
+			qup_uart9_tx: qup-uart9-tx {
+				pins = "gpio38";
+				function = "qup11";
+			};
+
+			qup_uart9_rx: qup-uart9-rx {
+				pins = "gpio39";
+				function = "qup11";
+			};
+
+			qup_uart10_cts: qup-uart10-cts {
+				pins = "gpio40";
+				function = "qup12";
+			};
+
+			qup_uart10_rts: qup-uart10-rts {
+				pins = "gpio41";
+				function = "qup12";
+			};
+
+			qup_uart10_tx: qup-uart10-tx {
+				pins = "gpio42";
+				function = "qup12";
+			};
+
+			qup_uart10_rx: qup-uart10-rx {
+				pins = "gpio43";
+				function = "qup12";
+			};
+
+			qup_uart11_cts: qup-uart11-cts {
+				pins = "gpio44";
+				function = "qup13";
+			};
+
+			qup_uart11_rts: qup-uart11-rts {
+				pins = "gpio45";
+				function = "qup13";
+			};
+
+			qup_uart11_tx: qup-uart11-tx {
+				pins = "gpio46";
+				function = "qup13";
+			};
+
+			qup_uart11_rx: qup-uart11-rx {
+				pins = "gpio47";
+				function = "qup13";
+			};
+
+			qup_uart12_cts: qup-uart12-cts {
+				pins = "gpio48";
+				function = "qup14";
+			};
+
+			qup_uart12_rts: qup-uart12-rts {
+				pins = "gpio49";
+				function = "qup14";
+			};
+
+			qup_uart12_tx: qup-uart12-tx {
+				pins = "gpio50";
+				function = "qup14";
+			};
+
+			qup_uart12_rx: qup-uart12-rx {
+				pins = "gpio51";
+				function = "qup14";
+			};
+
+			qup_uart13_cts: qup-uart13-cts {
+				pins = "gpio52";
+				function = "qup15";
+			};
+
+			qup_uart13_rts: qup-uart13-rts {
+				pins = "gpio53";
+				function = "qup15";
+			};
+
+			qup_uart13_tx: qup-uart13-tx {
+				pins = "gpio54";
+				function = "qup15";
+			};
+
+			qup_uart13_rx: qup-uart13-rx {
+				pins = "gpio55";
+				function = "qup15";
+			};
+
+			qup_uart14_cts: qup-uart14-cts {
+				pins = "gpio56";
+				function = "qup16";
+			};
+
+			qup_uart14_rts: qup-uart14-rts {
+				pins = "gpio57";
+				function = "qup16";
+			};
+
+			qup_uart14_tx: qup-uart14-tx {
+				pins = "gpio58";
+				function = "qup16";
+			};
+
+			qup_uart14_rx: qup-uart14-rx {
+				pins = "gpio59";
+				function = "qup16";
+			};
+
+			qup_uart15_cts: qup-uart15-cts {
+				pins = "gpio60";
+				function = "qup17";
+			};
+
+			qup_uart15_rts: qup-uart15-rts {
+				pins = "gpio61";
+				function = "qup17";
+			};
+
+			qup_uart15_tx: qup-uart15-tx {
+				pins = "gpio62";
+				function = "qup17";
+			};
+
+			qup_uart15_rx: qup-uart15-rx {
+				pins = "gpio63";
+				function = "qup17";
+			};
+		};
+
+		imem@146a5000 {
+			compatible = "qcom,sc7280-imem", "syscon";
+			reg = <0 0x146a5000 0 0x6000>;
+
+			#address-cells = <1>;
+			#size-cells = <1>;
+
+			ranges = <0 0 0x146a5000 0x6000>;
+
+			pil-reloc@594c {
+				compatible = "qcom,pil-reloc-info";
+				reg = <0x594c 0xc8>;
+			};
 		};
 
 		apps_smmu: iommu@15000000 {
@@ -2471,16 +4433,16 @@
 		};
 
 		gpuss0-thermal {
-			polling-delay-passive = <0>;
+			polling-delay-passive = <100>;
 			polling-delay = <0>;
 
 			thermal-sensors = <&tsens1 1>;
 
 			trips {
 				gpuss0_alert0: trip-point0 {
-					temperature = <90000>;
+					temperature = <95000>;
 					hysteresis = <2000>;
-					type = "hot";
+					type = "passive";
 				};
 
 				gpuss0_crit: gpuss0-crit {
@@ -2489,19 +4451,26 @@
 					type = "critical";
 				};
 			};
+
+			cooling-maps {
+				map0 {
+					trip = <&gpuss0_alert0>;
+					cooling-device = <&gpu THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
+				};
+			};
 		};
 
 		gpuss1-thermal {
-			polling-delay-passive = <0>;
+			polling-delay-passive = <100>;
 			polling-delay = <0>;
 
 			thermal-sensors = <&tsens1 2>;
 
 			trips {
 				gpuss1_alert0: trip-point0 {
-					temperature = <90000>;
+					temperature = <95000>;
 					hysteresis = <2000>;
-					type = "hot";
+					type = "passive";
 				};
 
 				gpuss1_crit: gpuss1-crit {
@@ -2510,6 +4479,13 @@
 					type = "critical";
 				};
 			};
+
+			cooling-maps {
+				map0 {
+					trip = <&gpuss1_alert0>;
+					cooling-device = <&gpu THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
+				};
+			};
 		};
 
 		nspss0-thermal {
diff --git a/arch/arm64/boot/dts/qcom/sdm630-sony-xperia-ganges-kirin.dts b/arch/arm64/boot/dts/qcom/sdm630-sony-xperia-ganges-kirin.dts
index a4e1fb8ca52d..71b448978e88 100644
--- a/arch/arm64/boot/dts/qcom/sdm630-sony-xperia-ganges-kirin.dts
+++ b/arch/arm64/boot/dts/qcom/sdm630-sony-xperia-ganges-kirin.dts
@@ -11,6 +11,7 @@
 / {
 	model = "Sony Xperia 10";
 	compatible = "sony,kirin-row", "qcom,sdm630";
+	chassis-type = "handset";
 
 	chosen {
 		framebuffer@9d400000 {
diff --git a/arch/arm64/boot/dts/qcom/sdm630-sony-xperia-nile-discovery.dts b/arch/arm64/boot/dts/qcom/sdm630-sony-xperia-nile-discovery.dts
index c574e430ba67..dd484a9bc7cd 100644
--- a/arch/arm64/boot/dts/qcom/sdm630-sony-xperia-nile-discovery.dts
+++ b/arch/arm64/boot/dts/qcom/sdm630-sony-xperia-nile-discovery.dts
@@ -11,4 +11,5 @@
 / {
 	model = "Sony Xperia XA2 Ultra";
 	compatible = "sony,discovery-row", "qcom,sdm630";
+	chassis-type = "handset";
 };
diff --git a/arch/arm64/boot/dts/qcom/sdm630-sony-xperia-nile-pioneer.dts b/arch/arm64/boot/dts/qcom/sdm630-sony-xperia-nile-pioneer.dts
index a93ff3ab1b6d..2da83cd41187 100644
--- a/arch/arm64/boot/dts/qcom/sdm630-sony-xperia-nile-pioneer.dts
+++ b/arch/arm64/boot/dts/qcom/sdm630-sony-xperia-nile-pioneer.dts
@@ -11,4 +11,5 @@
 / {
 	model = "Sony Xperia XA2";
 	compatible = "sony,pioneer-row", "qcom,sdm630";
+	chassis-type = "handset";
 };
diff --git a/arch/arm64/boot/dts/qcom/sdm630-sony-xperia-nile-voyager.dts b/arch/arm64/boot/dts/qcom/sdm630-sony-xperia-nile-voyager.dts
index 59a679c205e0..a679d4acee29 100644
--- a/arch/arm64/boot/dts/qcom/sdm630-sony-xperia-nile-voyager.dts
+++ b/arch/arm64/boot/dts/qcom/sdm630-sony-xperia-nile-voyager.dts
@@ -11,6 +11,7 @@
 / {
 	model = "Sony Xperia XA2 Plus";
 	compatible = "sony,voyager-row", "qcom,sdm630";
+	chassis-type = "handset";
 
 	chosen {
 		framebuffer@9d400000 {
diff --git a/arch/arm64/boot/dts/qcom/sdm630-sony-xperia-nile.dtsi b/arch/arm64/boot/dts/qcom/sdm630-sony-xperia-nile.dtsi
index 849900e8b80e..11d0a8c1cf35 100644
--- a/arch/arm64/boot/dts/qcom/sdm630-sony-xperia-nile.dtsi
+++ b/arch/arm64/boot/dts/qcom/sdm630-sony-xperia-nile.dtsi
@@ -308,7 +308,7 @@
 			regulator-allow-set-load;
 		};
 
-		vreg_l4b_29p5: l4 {
+		vreg_l4b_2p95: l4 {
 			regulator-min-microvolt = <2944000>;
 			regulator-max-microvolt = <2952000>;
 			regulator-enable-ramp-delay = <250>;
@@ -327,7 +327,7 @@
 		 * Tighten the range to 1.8-3.328 (closest to 3.3) to
 		 * make the mmc driver happy.
 		 */
-		vreg_l5b_29p5: l5 {
+		vreg_l5b_2p95: l5 {
 			regulator-min-microvolt = <1800000>;
 			regulator-max-microvolt = <3328000>;
 			regulator-enable-ramp-delay = <250>;
@@ -559,14 +559,14 @@
 	mmc-hs400-1_8v;
 	mmc-hs400-enhanced-strobe;
 
-	vmmc-supply = <&vreg_l4b_29p5>;
+	vmmc-supply = <&vreg_l4b_2p95>;
 	vqmmc-supply = <&vreg_l8a_1p8>;
 };
 
 &sdhc_2 {
 	status = "okay";
 
-	vmmc-supply = <&vreg_l5b_29p5>;
+	vmmc-supply = <&vreg_l5b_2p95>;
 	vqmmc-supply = <&vreg_l2b_2p95>;
 };
 
diff --git a/arch/arm64/boot/dts/qcom/sdm630.dtsi b/arch/arm64/boot/dts/qcom/sdm630.dtsi
index 9c7f87e42fcc..3e0165bb61c5 100644
--- a/arch/arm64/boot/dts/qcom/sdm630.dtsi
+++ b/arch/arm64/boot/dts/qcom/sdm630.dtsi
@@ -541,7 +541,7 @@
 					<&sleep_clk>;
 		};
 
-		rpm_msg_ram: memory@778000 {
+		rpm_msg_ram: sram@778000 {
 			compatible = "qcom,rpm-msg-ram";
 			reg = <0x00778000 0x7000>;
 		};
@@ -1176,6 +1176,11 @@
 			status = "disabled";
 		};
 
+		sram@290000 {
+			compatible = "qcom,rpm-stats";
+			reg = <0x00290000 0x10000>;
+		};
+
 		spmi_bus: spmi@800f000 {
 			compatible = "qcom,spmi-pmic-arb";
 			reg =	<0x0800f000 0x1000>,
@@ -2020,6 +2025,57 @@
 			};
 		};
 
+		venus: video-codec@cc00000 {
+			compatible = "qcom,sdm660-venus";
+			reg = <0x0cc00000 0xff000>;
+			clocks = <&mmcc VIDEO_CORE_CLK>,
+				 <&mmcc VIDEO_AHB_CLK>,
+				 <&mmcc VIDEO_AXI_CLK>,
+				 <&mmcc THROTTLE_VIDEO_AXI_CLK>;
+			clock-names = "core", "iface", "bus", "bus_throttle";
+			interconnects = <&gnoc 0 &mnoc 13>,
+					<&mnoc 4 &bimc 5>;
+			interconnect-names = "cpu-cfg", "video-mem";
+			interrupts = <GIC_SPI 287 IRQ_TYPE_LEVEL_HIGH>;
+			iommus = <&mmss_smmu 0x400>,
+				 <&mmss_smmu 0x401>,
+				 <&mmss_smmu 0x40a>,
+				 <&mmss_smmu 0x407>,
+				 <&mmss_smmu 0x40e>,
+				 <&mmss_smmu 0x40f>,
+				 <&mmss_smmu 0x408>,
+				 <&mmss_smmu 0x409>,
+				 <&mmss_smmu 0x40b>,
+				 <&mmss_smmu 0x40c>,
+				 <&mmss_smmu 0x40d>,
+				 <&mmss_smmu 0x410>,
+				 <&mmss_smmu 0x421>,
+				 <&mmss_smmu 0x428>,
+				 <&mmss_smmu 0x429>,
+				 <&mmss_smmu 0x42b>,
+				 <&mmss_smmu 0x42c>,
+				 <&mmss_smmu 0x42d>,
+				 <&mmss_smmu 0x411>,
+				 <&mmss_smmu 0x431>;
+			memory-region = <&venus_region>;
+			power-domains = <&mmcc VENUS_GDSC>;
+			status = "disabled";
+
+			video-decoder {
+				compatible = "venus-decoder";
+				clocks = <&mmcc VIDEO_SUBCORE0_CLK>;
+				clock-names = "vcodec0_core";
+				power-domains = <&mmcc VENUS_CORE0_GDSC>;
+			};
+
+			video-encoder {
+				compatible = "venus-encoder";
+				clocks = <&mmcc VIDEO_SUBCORE0_CLK>;
+				clock-names = "vcodec0_core";
+				power-domains = <&mmcc VENUS_CORE0_GDSC>;
+			};
+		};
+
 		mmss_smmu: iommu@cd00000 {
 			compatible = "qcom,sdm630-smmu-v2", "qcom,smmu-v2";
 			reg = <0x0cd00000 0x40000>;
diff --git a/arch/arm64/boot/dts/qcom/sdm660-xiaomi-lavender.dts b/arch/arm64/boot/dts/qcom/sdm660-xiaomi-lavender.dts
index 3e677fb7cfea..1edc53fd6941 100644
--- a/arch/arm64/boot/dts/qcom/sdm660-xiaomi-lavender.dts
+++ b/arch/arm64/boot/dts/qcom/sdm660-xiaomi-lavender.dts
@@ -10,6 +10,7 @@
 / {
 	model = "Xiaomi Redmi Note 7";
 	compatible = "xiaomi,lavender", "qcom,sdm660";
+	chassis-type = "handset";
 
 	aliases {
 		serial0 = &blsp1_uart2;
diff --git a/arch/arm64/boot/dts/qcom/sdm845-cheza.dtsi b/arch/arm64/boot/dts/qcom/sdm845-cheza.dtsi
index dfd1b42c07fd..4a6285a25f77 100644
--- a/arch/arm64/boot/dts/qcom/sdm845-cheza.dtsi
+++ b/arch/arm64/boot/dts/qcom/sdm845-cheza.dtsi
@@ -5,7 +5,6 @@
  * Copyright 2018 Google LLC.
  */
 
-#include <dt-bindings/gpio/gpio.h>
 #include <dt-bindings/input/input.h>
 #include <dt-bindings/regulator/qcom,rpmh-regulator.h>
 #include "sdm845.dtsi"
@@ -616,6 +615,14 @@ ap_ts_i2c: &i2c14 {
 	};
 };
 
+&gmu {
+	status = "okay";
+};
+
+&gpu {
+	status = "okay";
+};
+
 &ipa {
 	status = "okay";
 	modem-init;
@@ -629,10 +636,6 @@ ap_ts_i2c: &i2c14 {
 	status = "okay";
 };
 
-&mdss_mdp {
-	status = "okay";
-};
-
 /*
  * Cheza fw does not properly program the GPU aperture to allow the
  * GPU to update the SMMU pagetables for context switches.  Work
@@ -643,6 +646,8 @@ ap_ts_i2c: &i2c14 {
 };
 
 &mss_pil {
+	status = "okay";
+
 	iommus = <&apps_smmu 0x781 0x0>,
 		 <&apps_smmu 0x724 0x3>;
 };
@@ -1317,6 +1322,8 @@ ap_ts_i2c: &i2c14 {
 };
 
 &venus {
+	status = "okay";
+
 	video-firmware {
 		iommus = <&apps_smmu 0x10b2 0x0>;
 	};
diff --git a/arch/arm64/boot/dts/qcom/sdm845-db845c.dts b/arch/arm64/boot/dts/qcom/sdm845-db845c.dts
index 2d5533dd4ec2..13f80a0b6faa 100644
--- a/arch/arm64/boot/dts/qcom/sdm845-db845c.dts
+++ b/arch/arm64/boot/dts/qcom/sdm845-db845c.dts
@@ -5,7 +5,6 @@
 
 /dts-v1/;
 
-#include <dt-bindings/gpio/gpio.h>
 #include <dt-bindings/pinctrl/qcom,pmic-gpio.h>
 #include <dt-bindings/regulator/qcom,rpmh-regulator.h>
 #include <dt-bindings/sound/qcom,q6afe.h>
@@ -17,6 +16,8 @@
 / {
 	model = "Thundercomm Dragonboard 845c";
 	compatible = "thundercomm,db845c", "qcom,sdm845";
+	qcom,msm-id = <341 0x20001>;
+	qcom,board-id = <8 0>;
 
 	aliases {
 		serial0 = &uart9;
@@ -420,7 +421,12 @@
 			   <GCC_LPASS_SWAY_CLK>;
 };
 
+&gmu {
+	status = "okay";
+};
+
 &gpu {
+	status = "okay";
 	zap-shader {
 		memory-region = <&gpu_mem>;
 		firmware-name = "qcom/sdm845/a630_zap.mbn";
@@ -485,10 +491,6 @@
 	status = "okay";
 };
 
-&mdss_mdp {
-	status = "okay";
-};
-
 &mss_pil {
 	status = "okay";
 	firmware-name = "qcom/sdm845/mba.mbn", "qcom/sdm845/modem.mbn";
@@ -999,6 +1001,10 @@
 	vdda-pll-supply = <&vreg_l26a_1p2>;
 };
 
+&venus {
+	status = "okay";
+};
+
 &wcd9340{
 	pinctrl-0 = <&wcd_intr_default>;
 	pinctrl-names = "default";
diff --git a/arch/arm64/boot/dts/qcom/sdm845-mtp.dts b/arch/arm64/boot/dts/qcom/sdm845-mtp.dts
index 52dd7a858231..5e6e8f4fb5be 100644
--- a/arch/arm64/boot/dts/qcom/sdm845-mtp.dts
+++ b/arch/arm64/boot/dts/qcom/sdm845-mtp.dts
@@ -7,7 +7,6 @@
 
 /dts-v1/;
 
-#include <dt-bindings/gpio/gpio.h>
 #include <dt-bindings/regulator/qcom,rpmh-regulator.h>
 #include "sdm845.dtsi"
 
@@ -361,9 +360,6 @@
 	qcom,dual-dsi-mode;
 	qcom,master-dsi;
 
-	#address-cells = <1>;
-	#size-cells = <0>;
-
 	ports {
 		port@1 {
 			endpoint {
@@ -439,7 +435,13 @@
 			   <GCC_LPASS_SWAY_CLK>;
 };
 
+&gmu {
+	status = "okay";
+};
+
 &gpu {
+	status = "okay";
+
 	zap-shader {
 		memory-region = <&gpu_mem>;
 		firmware-name = "qcom/sdm845/a630_zap.mbn";
@@ -460,10 +462,6 @@
 	status = "okay";
 };
 
-&mdss_mdp {
-	status = "okay";
-};
-
 &mss_pil {
 	status = "okay";
 	firmware-name = "qcom/sdm845/mba.mbn", "qcom/sdm845/modem.mbn";
@@ -566,6 +564,10 @@
 	vdda-pll-supply = <&vdda_usb2_ss_core>;
 };
 
+&venus {
+	status = "okay";
+};
+
 &wifi {
 	status = "okay";
 	vdd-0.8-cx-mx-supply = <&vreg_l5a_0p8>;
diff --git a/arch/arm64/boot/dts/qcom/sdm845-oneplus-common.dtsi b/arch/arm64/boot/dts/qcom/sdm845-oneplus-common.dtsi
index d4355522374a..3e04aeb479d1 100644
--- a/arch/arm64/boot/dts/qcom/sdm845-oneplus-common.dtsi
+++ b/arch/arm64/boot/dts/qcom/sdm845-oneplus-common.dtsi
@@ -7,7 +7,6 @@
 
 /dts-v1/;
 
-#include <dt-bindings/gpio/gpio.h>
 #include <dt-bindings/input/linux-event-codes.h>
 #include <dt-bindings/regulator/qcom,rpmh-regulator.h>
 
@@ -93,7 +92,6 @@
 			console-size = <0x40000>;
 			ftrace-size = <0x40000>;
 			pmsg-size = <0x200000>;
-			devinfo-size = <0x1000>;
 			ecc-size = <16>;
 		};
 	};
@@ -248,6 +246,12 @@
 			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
 		};
 
+		vreg_l23a_3p3: ldo23 {
+			regulator-min-microvolt = <3300000>;
+			regulator-max-microvolt = <3312000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
 		vdda_qusb_hs0_3p1:
 		vreg_l24a_3p075: ldo24 {
 			regulator-min-microvolt = <3088000>;
@@ -315,9 +319,6 @@
 	status = "okay";
 	vdda-supply = <&vdda_mipi_dsi0_1p2>;
 
-	#address-cells = <1>;
-	#size-cells = <0>;
-
 	/*
 	 * Both devices use different panels but all other properties
 	 * are common. Compatible line is declared in device dts.
@@ -362,7 +363,13 @@
 				<GCC_LPASS_SWAY_CLK>;
 };
 
+&gmu {
+	status = "okay";
+};
+
 &gpu {
+	status = "okay";
+
 	zap-shader {
 		memory-region = <&gpu_mem>;
 		firmware-name = "qcom/sdm845/oneplus6/a630_zap.mbn";
@@ -415,10 +422,6 @@
 	status = "okay";
 };
 
-&mdss_mdp {
-	status = "okay";
-};
-
 /* Modem/wifi*/
 &mss_pil {
 	status = "okay";
@@ -641,12 +644,17 @@
 	};
 };
 
+&venus {
+	status = "okay";
+};
+
 &wifi {
 	status = "okay";
 	vdd-0.8-cx-mx-supply = <&vreg_l5a_0p8>;
 	vdd-1.8-xo-supply = <&vreg_l7a_1p8>;
 	vdd-1.3-rfa-supply = <&vreg_l17a_1p3>;
 	vdd-3.3-ch0-supply = <&vreg_l25a_3p3>;
+	vdd-3.3-ch1-supply = <&vreg_l23a_3p3>;
 
 	qcom,snoc-host-cap-8bit-quirk;
 };
diff --git a/arch/arm64/boot/dts/qcom/sdm845-oneplus-enchilada.dts b/arch/arm64/boot/dts/qcom/sdm845-oneplus-enchilada.dts
index 72842c887617..73493079d13e 100644
--- a/arch/arm64/boot/dts/qcom/sdm845-oneplus-enchilada.dts
+++ b/arch/arm64/boot/dts/qcom/sdm845-oneplus-enchilada.dts
@@ -10,6 +10,7 @@
 / {
 	model = "OnePlus 6";
 	compatible = "oneplus,enchilada", "qcom,sdm845";
+	chassis-type = "handset";
 };
 
 &display_panel {
diff --git a/arch/arm64/boot/dts/qcom/sdm845-oneplus-fajita.dts b/arch/arm64/boot/dts/qcom/sdm845-oneplus-fajita.dts
index 969b36dc9e2c..b63ebc48f62f 100644
--- a/arch/arm64/boot/dts/qcom/sdm845-oneplus-fajita.dts
+++ b/arch/arm64/boot/dts/qcom/sdm845-oneplus-fajita.dts
@@ -10,6 +10,7 @@
 / {
 	model = "OnePlus 6T";
 	compatible = "oneplus,fajita", "qcom,sdm845";
+	chassis-type = "handset";
 };
 
 &display_panel {
diff --git a/arch/arm64/boot/dts/qcom/sdm845-xiaomi-beryllium.dts b/arch/arm64/boot/dts/qcom/sdm845-xiaomi-beryllium.dts
index c60c8c640e17..580d4cc1296f 100644
--- a/arch/arm64/boot/dts/qcom/sdm845-xiaomi-beryllium.dts
+++ b/arch/arm64/boot/dts/qcom/sdm845-xiaomi-beryllium.dts
@@ -2,7 +2,6 @@
 
 /dts-v1/;
 
-#include <dt-bindings/gpio/gpio.h>
 #include <dt-bindings/pinctrl/qcom,pmic-gpio.h>
 #include <dt-bindings/regulator/qcom,rpmh-regulator.h>
 #include <dt-bindings/sound/qcom,q6afe.h>
@@ -29,6 +28,7 @@
 / {
 	model = "Xiaomi Pocophone F1";
 	compatible = "xiaomi,beryllium", "qcom,sdm845";
+	chassis-type = "handset";
 
 	/* required for bootloader to select correct board */
 	qcom,board-id = <69 0>;
@@ -215,9 +215,6 @@
 	status = "okay";
 	vdda-supply = <&vreg_l26a_1p2>;
 
-	#address-cells = <1>;
-	#size-cells = <0>;
-
 	panel@0 {
 		compatible = "tianma,fhd-video";
 		reg = <0>;
@@ -256,7 +253,13 @@
 			   <GCC_LPASS_SWAY_CLK>;
 };
 
+&gmu {
+	status = "okay";
+};
+
 &gpu {
+	status = "okay";
+
 	zap-shader {
 		memory-region = <&gpu_mem>;
 		firmware-name = "qcom/sdm845/a630_zap.mbn";
@@ -284,10 +287,6 @@
 	status = "okay";
 };
 
-&mdss_mdp {
-	status = "okay";
-};
-
 &mss_pil {
 	status = "okay";
 	firmware-name = "qcom/sdm845/mba.mbn", "qcom/sdm845/modem.mdt";
@@ -513,6 +512,10 @@
 	vdda-pll-supply = <&vreg_l1a_0p875>;
 };
 
+&venus {
+	status = "okay";
+};
+
 &wcd9340{
 	pinctrl-0 = <&wcd_intr_default>;
 	pinctrl-names = "default";
diff --git a/arch/arm64/boot/dts/qcom/sdm845.dtsi b/arch/arm64/boot/dts/qcom/sdm845.dtsi
index b3b911926184..526087586ba4 100644
--- a/arch/arm64/boot/dts/qcom/sdm845.dtsi
+++ b/arch/arm64/boot/dts/qcom/sdm845.dtsi
@@ -12,6 +12,7 @@
 #include <dt-bindings/clock/qcom,lpass-sdm845.h>
 #include <dt-bindings/clock/qcom,rpmh.h>
 #include <dt-bindings/clock/qcom,videocc-sdm845.h>
+#include <dt-bindings/gpio/gpio.h>
 #include <dt-bindings/interconnect/qcom,osm-l3.h>
 #include <dt-bindings/interconnect/qcom,sdm845.h>
 #include <dt-bindings/interrupt-controller/arm-gic.h>
@@ -99,9 +100,11 @@
 			no-map;
 		};
 
-		smem_mem: memory@86000000 {
+		smem@86000000 {
+			compatible = "qcom,smem";
 			reg = <0x0 0x86000000 0 0x200000>;
 			no-map;
+			hwlocks = <&tcsr_mutex 3>;
 		};
 
 		tz_mem: memory@86200000 {
@@ -768,6 +771,8 @@
 
 		memory-region = <&adsp_mem>;
 
+		qcom,qmp = <&aoss_qmp>;
+
 		qcom,smem-states = <&adsp_smp2p_out 0>;
 		qcom,smem-state-names = "stop";
 
@@ -867,6 +872,8 @@
 
 		memory-region = <&cdsp_mem>;
 
+		qcom,qmp = <&aoss_qmp>;
+
 		qcom,smem-states = <&cdsp_smp2p_out 0>;
 		qcom,smem-state-names = "stop";
 
@@ -941,12 +948,6 @@
 		#hwlock-cells = <1>;
 	};
 
-	smem {
-		compatible = "qcom,smem";
-		memory-region = <&smem_mem>;
-		hwlocks = <&tcsr_mutex 3>;
-	};
-
 	smp2p-cdsp {
 		compatible = "qcom,smp2p";
 		qcom,smem = <94>, <432>;
@@ -1995,10 +1996,10 @@
 			interrupt-names = "msi";
 			#interrupt-cells = <1>;
 			interrupt-map-mask = <0 0 0 0x7>;
-			interrupt-map = <0 0 0 1 &intc 0 149 IRQ_TYPE_LEVEL_HIGH>, /* int_a */
-					<0 0 0 2 &intc 0 150 IRQ_TYPE_LEVEL_HIGH>, /* int_b */
-					<0 0 0 3 &intc 0 151 IRQ_TYPE_LEVEL_HIGH>, /* int_c */
-					<0 0 0 4 &intc 0 152 IRQ_TYPE_LEVEL_HIGH>; /* int_d */
+			interrupt-map = <0 0 0 1 &intc 0 0 0 149 IRQ_TYPE_LEVEL_HIGH>, /* int_a */
+					<0 0 0 2 &intc 0 0 0 150 IRQ_TYPE_LEVEL_HIGH>, /* int_b */
+					<0 0 0 3 &intc 0 0 0 151 IRQ_TYPE_LEVEL_HIGH>, /* int_c */
+					<0 0 0 4 &intc 0 0 0 152 IRQ_TYPE_LEVEL_HIGH>; /* int_d */
 
 			clocks = <&gcc GCC_PCIE_0_PIPE_CLK>,
 				 <&gcc GCC_PCIE_0_AUX_CLK>,
@@ -2064,7 +2065,7 @@
 
 			status = "disabled";
 
-			pcie0_lane: lanes@1c06200 {
+			pcie0_lane: phy@1c06200 {
 				reg = <0 0x01c06200 0 0x128>,
 				      <0 0x01c06400 0 0x1fc>,
 				      <0 0x01c06800 0 0x218>,
@@ -2100,10 +2101,10 @@
 			interrupt-names = "msi";
 			#interrupt-cells = <1>;
 			interrupt-map-mask = <0 0 0 0x7>;
-			interrupt-map = <0 0 0 1 &intc 0 434 IRQ_TYPE_LEVEL_HIGH>, /* int_a */
-					<0 0 0 2 &intc 0 435 IRQ_TYPE_LEVEL_HIGH>, /* int_b */
-					<0 0 0 3 &intc 0 438 IRQ_TYPE_LEVEL_HIGH>, /* int_c */
-					<0 0 0 4 &intc 0 439 IRQ_TYPE_LEVEL_HIGH>; /* int_d */
+			interrupt-map = <0 0 0 1 &intc 0 0 0 434 IRQ_TYPE_LEVEL_HIGH>, /* int_a */
+					<0 0 0 2 &intc 0 0 0 435 IRQ_TYPE_LEVEL_HIGH>, /* int_b */
+					<0 0 0 3 &intc 0 0 0 438 IRQ_TYPE_LEVEL_HIGH>, /* int_c */
+					<0 0 0 4 &intc 0 0 0 439 IRQ_TYPE_LEVEL_HIGH>; /* int_d */
 
 			clocks = <&gcc GCC_PCIE_1_PIPE_CLK>,
 				 <&gcc GCC_PCIE_1_AUX_CLK>,
@@ -2174,7 +2175,7 @@
 
 			status = "disabled";
 
-			pcie1_lane: lanes@1c06200 {
+			pcie1_lane: phy@1c06200 {
 				reg = <0 0x01c0a800 0 0x800>,
 				      <0 0x01c0a800 0 0x800>,
 				      <0 0x01c0b800 0 0x400>;
@@ -2302,7 +2303,7 @@
 			reset-names = "ufsphy";
 			status = "disabled";
 
-			ufs_mem_phy_lanes: lanes@1d87400 {
+			ufs_mem_phy_lanes: phy@1d87400 {
 				reg = <0 0x01d87400 0 0x108>,
 				      <0 0x01d87600 0 0x1e0>,
 				      <0 0x01d87c00 0 0x1dc>,
@@ -2312,15 +2313,15 @@
 			};
 		};
 
-		cryptobam: dma@1dc4000 {
+		cryptobam: dma-controller@1dc4000 {
 			compatible = "qcom,bam-v1.7.0";
 			reg = <0 0x01dc4000 0 0x24000>;
 			interrupts = <GIC_SPI 272 IRQ_TYPE_LEVEL_HIGH>;
-			clocks = <&rpmhcc 15>;
+			clocks = <&rpmhcc RPMH_CE_CLK>;
 			clock-names = "bam_clk";
 			#dma-cells = <1>;
 			qcom,ee = <0>;
-			qcom,controlled-remotely = <1>;
+			qcom,controlled-remotely;
 			iommus = <&apps_smmu 0x704 0x1>,
 				 <&apps_smmu 0x706 0x1>,
 				 <&apps_smmu 0x714 0x1>,
@@ -2331,8 +2332,8 @@
 			compatible = "qcom,crypto-v5.4";
 			reg = <0 0x01dfa000 0 0x6000>;
 			clocks = <&gcc GCC_CE1_AHB_CLK>,
-				 <&gcc GCC_CE1_AHB_CLK>,
-				 <&rpmhcc 15>;
+				 <&gcc GCC_CE1_AXI_CLK>,
+				 <&rpmhcc RPMH_CE_CLK>;
 			clock-names = "iface", "bus", "core";
 			dmas = <&cryptobam 6>, <&cryptobam 7>;
 			dma-names = "rx", "tx";
@@ -2984,6 +2985,8 @@
 			clock-names = "iface", "bus", "mem", "gpll0_mss",
 				      "snoc_axi", "mnoc_axi", "prng", "xo";
 
+			qcom,qmp = <&aoss_qmp>;
+
 			qcom,smem-states = <&modem_smp2p_out 0>;
 			qcom,smem-state-names = "stop";
 
@@ -2993,11 +2996,12 @@
 
 			qcom,halt-regs = <&tcsr_mutex_regs 0x23000 0x25000 0x24000>;
 
-			power-domains = <&aoss_qmp 2>,
-					<&rpmhpd SDM845_CX>,
+			power-domains = <&rpmhpd SDM845_CX>,
 					<&rpmhpd SDM845_MX>,
 					<&rpmhpd SDM845_MSS>;
-			power-domain-names = "load_state", "cx", "mx", "mss";
+			power-domain-names = "cx", "mx", "mss";
+
+			status = "disabled";
 
 			mba {
 				memory-region = <&mba_region>;
@@ -3497,8 +3501,9 @@
 			interrupt-names = "hc_irq", "pwr_irq";
 
 			clocks = <&gcc GCC_SDCC2_AHB_CLK>,
-				 <&gcc GCC_SDCC2_APPS_CLK>;
-			clock-names = "iface", "core";
+				 <&gcc GCC_SDCC2_APPS_CLK>,
+				 <&rpmhcc RPMH_CXO_CLK>;
+			clock-names = "iface", "core", "xo";
 			iommus = <&apps_smmu 0xa0 0xf>;
 			power-domains = <&rpmhpd SDM845_CX>;
 			operating-points-v2 = <&sdhc2_opp_table>;
@@ -3646,6 +3651,30 @@
 			};
 		};
 
+		lmh_cluster1: lmh@17d70800 {
+			compatible = "qcom,sdm845-lmh";
+			reg = <0 0x17d70800 0 0x400>;
+			interrupts = <GIC_SPI 33 IRQ_TYPE_LEVEL_HIGH>;
+			cpus = <&CPU4>;
+			qcom,lmh-temp-arm-millicelsius = <65000>;
+			qcom,lmh-temp-low-millicelsius = <94500>;
+			qcom,lmh-temp-high-millicelsius = <95000>;
+			interrupt-controller;
+			#interrupt-cells = <1>;
+		};
+
+		lmh_cluster0: lmh@17d78800 {
+			compatible = "qcom,sdm845-lmh";
+			reg = <0 0x17d78800 0 0x400>;
+			interrupts = <GIC_SPI 32 IRQ_TYPE_LEVEL_HIGH>;
+			cpus = <&CPU0>;
+			qcom,lmh-temp-arm-millicelsius = <65000>;
+			qcom,lmh-temp-low-millicelsius = <94500>;
+			qcom,lmh-temp-high-millicelsius = <95000>;
+			interrupt-controller;
+			#interrupt-cells = <1>;
+		};
+
 		sound: sound {
 		};
 
@@ -3683,7 +3712,6 @@
 			compatible = "qcom,sdm845-qmp-usb3-phy";
 			reg = <0 0x088e9000 0 0x18c>,
 			      <0 0x088e8000 0 0x10>;
-			reg-names = "reg-base", "dp_com";
 			status = "disabled";
 			#address-cells = <2>;
 			#size-cells = <2>;
@@ -3699,7 +3727,7 @@
 				 <&gcc GCC_USB3_PHY_PRIM_BCR>;
 			reset-names = "phy", "common";
 
-			usb_1_ssphy: lanes@88e9200 {
+			usb_1_ssphy: phy@88e9200 {
 				reg = <0 0x088e9200 0 0x128>,
 				      <0 0x088e9400 0 0x200>,
 				      <0 0x088e9c00 0 0x218>,
@@ -3732,7 +3760,7 @@
 				 <&gcc GCC_USB3_PHY_SEC_BCR>;
 			reset-names = "phy", "common";
 
-			usb_2_ssphy: lane@88eb200 {
+			usb_2_ssphy: phy@88eb200 {
 				reg = <0 0x088eb200 0 0x128>,
 				      <0 0x088eb400 0 0x1fc>,
 				      <0 0x088eb800 0 0x218>,
@@ -3868,6 +3896,8 @@
 					<&gladiator_noc MASTER_APPSS_PROC 0 &config_noc SLAVE_VENUS_CFG 0>;
 			interconnect-names = "video-mem", "cpu-cfg";
 
+			status = "disabled";
+
 			video-core0 {
 				compatible = "venus-decoder";
 			};
@@ -4194,8 +4224,6 @@
 				interrupt-parent = <&mdss>;
 				interrupts = <0 IRQ_TYPE_LEVEL_HIGH>;
 
-				status = "disabled";
-
 				ports {
 					#address-cells = <1>;
 					#size-cells = <0>;
@@ -4271,6 +4299,9 @@
 
 				status = "disabled";
 
+				#address-cells = <1>;
+				#size-cells = <0>;
+
 				ports {
 					#address-cells = <1>;
 					#size-cells = <0>;
@@ -4340,6 +4371,9 @@
 
 				status = "disabled";
 
+				#address-cells = <1>;
+				#size-cells = <0>;
+
 				ports {
 					#address-cells = <1>;
 					#size-cells = <0>;
@@ -4402,6 +4436,8 @@
 			interconnects = <&mem_noc MASTER_GFX3D 0 &mem_noc SLAVE_EBI1 0>;
 			interconnect-names = "gfx-mem";
 
+			status = "disabled";
+
 			gpu_opp_table: opp-table {
 				compatible = "operating-points-v2";
 
@@ -4497,6 +4533,8 @@
 
 			operating-points-v2 = <&gmu_opp_table>;
 
+			status = "disabled";
+
 			gmu_opp_table: opp-table {
 				compatible = "operating-points-v2";
 
@@ -4588,7 +4626,6 @@
 			mboxes = <&apss_shared 0>;
 
 			#clock-cells = <0>;
-			#power-domain-cells = <1>;
 
 			cx_cdev: cx {
 				#cooling-cells = <2>;
@@ -4917,6 +4954,8 @@
 			reg = <0 0x17d43000 0 0x1400>, <0 0x17d45800 0 0x1400>;
 			reg-names = "freq-domain0", "freq-domain1";
 
+			interrupts-extended = <&lmh_cluster0 0>, <&lmh_cluster1 0>;
+
 			clocks = <&rpmhcc RPMH_CXO_CLK>, <&gcc GPLL0>;
 			clock-names = "xo", "alternate";
 
@@ -4974,23 +5013,6 @@
 					type = "critical";
 				};
 			};
-
-			cooling-maps {
-				map0 {
-					trip = <&cpu0_alert0>;
-					cooling-device = <&CPU0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
-							 <&CPU1 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
-							 <&CPU2 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
-							 <&CPU3 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
-				};
-				map1 {
-					trip = <&cpu0_alert1>;
-					cooling-device = <&CPU0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
-							 <&CPU1 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
-							 <&CPU2 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
-							 <&CPU3 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
-				};
-			};
 		};
 
 		cpu1-thermal {
@@ -5018,23 +5040,6 @@
 					type = "critical";
 				};
 			};
-
-			cooling-maps {
-				map0 {
-					trip = <&cpu1_alert0>;
-					cooling-device = <&CPU0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
-							 <&CPU1 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
-							 <&CPU2 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
-							 <&CPU3 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
-				};
-				map1 {
-					trip = <&cpu1_alert1>;
-					cooling-device = <&CPU0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
-							 <&CPU1 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
-							 <&CPU2 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
-							 <&CPU3 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
-				};
-			};
 		};
 
 		cpu2-thermal {
@@ -5062,23 +5067,6 @@
 					type = "critical";
 				};
 			};
-
-			cooling-maps {
-				map0 {
-					trip = <&cpu2_alert0>;
-					cooling-device = <&CPU0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
-							 <&CPU1 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
-							 <&CPU2 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
-							 <&CPU3 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
-				};
-				map1 {
-					trip = <&cpu2_alert1>;
-					cooling-device = <&CPU0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
-							 <&CPU1 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
-							 <&CPU2 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
-							 <&CPU3 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
-				};
-			};
 		};
 
 		cpu3-thermal {
@@ -5106,23 +5094,6 @@
 					type = "critical";
 				};
 			};
-
-			cooling-maps {
-				map0 {
-					trip = <&cpu3_alert0>;
-					cooling-device = <&CPU0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
-							 <&CPU1 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
-							 <&CPU2 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
-							 <&CPU3 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
-				};
-				map1 {
-					trip = <&cpu3_alert1>;
-					cooling-device = <&CPU0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
-							 <&CPU1 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
-							 <&CPU2 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
-							 <&CPU3 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
-				};
-			};
 		};
 
 		cpu4-thermal {
@@ -5150,23 +5121,6 @@
 					type = "critical";
 				};
 			};
-
-			cooling-maps {
-				map0 {
-					trip = <&cpu4_alert0>;
-					cooling-device = <&CPU4 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
-							 <&CPU5 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
-							 <&CPU6 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
-							 <&CPU7 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
-				};
-				map1 {
-					trip = <&cpu4_alert1>;
-					cooling-device = <&CPU4 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
-							 <&CPU5 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
-							 <&CPU6 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
-							 <&CPU7 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
-				};
-			};
 		};
 
 		cpu5-thermal {
@@ -5194,23 +5148,6 @@
 					type = "critical";
 				};
 			};
-
-			cooling-maps {
-				map0 {
-					trip = <&cpu5_alert0>;
-					cooling-device = <&CPU4 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
-							 <&CPU5 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
-							 <&CPU6 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
-							 <&CPU7 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
-				};
-				map1 {
-					trip = <&cpu5_alert1>;
-					cooling-device = <&CPU4 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
-							 <&CPU5 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
-							 <&CPU6 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
-							 <&CPU7 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
-				};
-			};
 		};
 
 		cpu6-thermal {
@@ -5238,23 +5175,6 @@
 					type = "critical";
 				};
 			};
-
-			cooling-maps {
-				map0 {
-					trip = <&cpu6_alert0>;
-					cooling-device = <&CPU4 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
-							 <&CPU5 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
-							 <&CPU6 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
-							 <&CPU7 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
-				};
-				map1 {
-					trip = <&cpu6_alert1>;
-					cooling-device = <&CPU4 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
-							 <&CPU5 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
-							 <&CPU6 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
-							 <&CPU7 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
-				};
-			};
 		};
 
 		cpu7-thermal {
@@ -5282,23 +5202,6 @@
 					type = "critical";
 				};
 			};
-
-			cooling-maps {
-				map0 {
-					trip = <&cpu7_alert0>;
-					cooling-device = <&CPU4 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
-							 <&CPU5 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
-							 <&CPU6 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
-							 <&CPU7 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
-				};
-				map1 {
-					trip = <&cpu7_alert1>;
-					cooling-device = <&CPU4 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
-							 <&CPU5 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
-							 <&CPU6 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
-							 <&CPU7 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
-				};
-			};
 		};
 
 		aoss0-thermal {
diff --git a/arch/arm64/boot/dts/qcom/sdm850-lenovo-yoga-c630.dts b/arch/arm64/boot/dts/qcom/sdm850-lenovo-yoga-c630.dts
index 2ba23aa582a1..d6b2ba4396f6 100644
--- a/arch/arm64/boot/dts/qcom/sdm850-lenovo-yoga-c630.dts
+++ b/arch/arm64/boot/dts/qcom/sdm850-lenovo-yoga-c630.dts
@@ -7,7 +7,6 @@
 
 /dts-v1/;
 
-#include <dt-bindings/gpio/gpio.h>
 #include <dt-bindings/input/gpio-keys.h>
 #include <dt-bindings/input/input.h>
 #include <dt-bindings/regulator/qcom,rpmh-regulator.h>
@@ -30,6 +29,7 @@
 / {
 	model = "Lenovo Yoga C630";
 	compatible = "lenovo,yoga-c630", "qcom,sdm845";
+	chassis-type = "convertible";
 
 	aliases {
 		hsuart0 = &uart6;
@@ -264,6 +264,9 @@
 		};
 
 		vreg_l23a_3p3: ldo23 {
+			regulator-min-microvolt = <3300000>;
+			regulator-max-microvolt = <3312000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
 		};
 
 		vdda_qusb_hs0_3p1:
@@ -341,7 +344,12 @@
 			   <GCC_LPASS_SWAY_CLK>;
 };
 
+&gmu {
+	status = "okay";
+};
+
 &gpu {
+	status = "okay";
 	zap-shader {
 		memory-region = <&gpu_mem>;
 		firmware-name = "qcom/LENOVO/81JL/qcdxkmsuc850.mbn";
@@ -458,11 +466,8 @@
 	status = "okay";
 };
 
-&mdss_mdp {
-	status = "okay";
-};
-
 &mss_pil {
+	status = "okay";
 	firmware-name = "qcom/LENOVO/81JL/qcdsp1v2850.mbn", "qcom/LENOVO/81JL/qcdsp2850.mbn";
 };
 
@@ -649,6 +654,7 @@
 		vddxo-supply = <&vreg_l7a_1p8>;
 		vddrf-supply = <&vreg_l17a_1p3>;
 		vddch0-supply = <&vreg_l25a_3p3>;
+		vddch1-supply = <&vreg_l23a_3p3>;
 		max-speed = <3200000>;
 	};
 };
@@ -723,6 +729,10 @@
 	vdda-pll-supply = <&vdda_usb2_ss_core>;
 };
 
+&venus {
+	status = "okay";
+};
+
 &wcd9340{
 	pinctrl-0 = <&wcd_intr_default>;
 	pinctrl-names = "default";
@@ -763,6 +773,7 @@
 	vdd-1.8-xo-supply = <&vreg_l7a_1p8>;
 	vdd-1.3-rfa-supply = <&vreg_l17a_1p3>;
 	vdd-3.3-ch0-supply = <&vreg_l25a_3p3>;
+	vdd-3.3-ch1-supply = <&vreg_l23a_3p3>;
 
 	qcom,snoc-host-cap-8bit-quirk;
 };
diff --git a/arch/arm64/boot/dts/qcom/sm6125-sony-xperia-seine-pdx201.dts b/arch/arm64/boot/dts/qcom/sm6125-sony-xperia-seine-pdx201.dts
index 58b6b2742d3f..45eab0235d66 100644
--- a/arch/arm64/boot/dts/qcom/sm6125-sony-xperia-seine-pdx201.dts
+++ b/arch/arm64/boot/dts/qcom/sm6125-sony-xperia-seine-pdx201.dts
@@ -17,6 +17,7 @@
 
 	model = "Sony Xperia 10 II";
 	compatible = "sony,pdx201", "qcom,sm6125";
+	chassis-type = "handset";
 
 	chosen {
 		#address-cells = <2>;
diff --git a/arch/arm64/boot/dts/qcom/sm6125.dtsi b/arch/arm64/boot/dts/qcom/sm6125.dtsi
index 2b37ce6a9f9c..51286ddbdb10 100644
--- a/arch/arm64/boot/dts/qcom/sm6125.dtsi
+++ b/arch/arm64/boot/dts/qcom/sm6125.dtsi
@@ -326,8 +326,8 @@
 		tlmm: pinctrl@500000 {
 			compatible = "qcom,sm6125-tlmm";
 			reg = <0x00500000 0x400000>,
-				<0x00900000 0x400000>,
-				<0x00d00000 0x400000>;
+			      <0x00900000 0x400000>,
+			      <0x00d00000 0x400000>;
 			reg-names = "west", "south", "east";
 			interrupts = <GIC_SPI 227 IRQ_TYPE_LEVEL_HIGH>;
 			gpio-controller;
@@ -380,7 +380,7 @@
 			status = "disabled";
 		};
 
-		rpm_msg_ram: memory@45f0000 {
+		rpm_msg_ram: sram@45f0000 {
 			compatible = "qcom,rpm-msg-ram";
 			reg = <0x045f0000 0x7000>;
 		};
@@ -391,12 +391,12 @@
 			reg-names = "hc", "core";
 
 			interrupts = <GIC_SPI 348 IRQ_TYPE_LEVEL_HIGH>,
-				<GIC_SPI 352 IRQ_TYPE_LEVEL_HIGH>;
+				     <GIC_SPI 352 IRQ_TYPE_LEVEL_HIGH>;
 			interrupt-names = "hc_irq", "pwr_irq";
 
 			clocks = <&gcc GCC_SDCC1_AHB_CLK>,
-				<&gcc GCC_SDCC1_APPS_CLK>,
-				<&xo_board>;
+				 <&gcc GCC_SDCC1_APPS_CLK>,
+				 <&xo_board>;
 			clock-names = "iface", "core", "xo";
 			bus-width = <8>;
 			non-removable;
@@ -409,12 +409,12 @@
 			reg-names = "hc";
 
 			interrupts = <GIC_SPI 350 IRQ_TYPE_LEVEL_HIGH>,
-				<GIC_SPI 353 IRQ_TYPE_LEVEL_HIGH>;
+				     <GIC_SPI 353 IRQ_TYPE_LEVEL_HIGH>;
 			interrupt-names = "hc_irq", "pwr_irq";
 
 			clocks = <&gcc GCC_SDCC2_AHB_CLK>,
-				<&gcc GCC_SDCC2_APPS_CLK>,
-				<&xo_board>;
+				 <&gcc GCC_SDCC2_APPS_CLK>,
+				 <&xo_board>;
 			clock-names = "iface", "core", "xo";
 
 			pinctrl-0 = <&sdc2_state_on>;
@@ -433,11 +433,11 @@
 			ranges;
 
 			clocks = <&gcc GCC_USB30_PRIM_MASTER_CLK>,
-				<&gcc GCC_SYS_NOC_USB3_PRIM_AXI_CLK>,
-				<&gcc GCC_CFG_NOC_USB3_PRIM_AXI_CLK>,
-				<&gcc GCC_USB3_PRIM_CLKREF_CLK>,
-				<&gcc GCC_USB30_PRIM_SLEEP_CLK>,
-				<&gcc GCC_USB30_PRIM_MOCK_UTMI_CLK>;
+				 <&gcc GCC_SYS_NOC_USB3_PRIM_AXI_CLK>,
+				 <&gcc GCC_CFG_NOC_USB3_PRIM_AXI_CLK>,
+				 <&gcc GCC_USB3_PRIM_CLKREF_CLK>,
+				 <&gcc GCC_USB30_PRIM_SLEEP_CLK>,
+				 <&gcc GCC_USB30_PRIM_MOCK_UTMI_CLK>;
 
 			assigned-clocks = <&gcc GCC_USB30_PRIM_MOCK_UTMI_CLK>,
 					  <&gcc GCC_USB30_PRIM_MASTER_CLK>;
@@ -460,13 +460,18 @@
 			};
 		};
 
+		sram@4690000 {
+			compatible = "qcom,rpm-stats";
+			reg = <0x04690000 0x10000>;
+		};
+
 		spmi_bus: spmi@1c40000 {
 			compatible = "qcom,spmi-pmic-arb";
-			reg =	<0x01c40000 0x1100>,
-				<0x01e00000 0x2000000>,
-				<0x03e00000 0x100000>,
-				<0x03f00000 0xa0000>,
-				<0x01c0a000 0x26000>;
+			reg = <0x01c40000 0x1100>,
+			      <0x01e00000 0x2000000>,
+			      <0x03e00000 0x100000>,
+			      <0x03f00000 0xa0000>,
+			      <0x01c0a000 0x26000>;
 			reg-names = "core", "chnls", "obsrvr", "intr", "cnfg";
 			interrupt-names = "periph_irq";
 			interrupts = <GIC_SPI 183 IRQ_TYPE_LEVEL_HIGH>;
@@ -494,22 +499,22 @@
 			reg = <0x0f120000 0x1000>;
 			clock-frequency = <19200000>;
 
-			frame@0f121000 {
+			frame@f121000 {
 				frame-number = <0>;
 				interrupts = <GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>,
-						<GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>;
+					     <GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>;
 				reg = <0x0f121000 0x1000>,
 				      <0x0f122000 0x1000>;
 			};
 
-			frame@0f123000 {
+			frame@f123000 {
 				frame-number = <1>;
 				interrupts = <GIC_SPI 9 IRQ_TYPE_LEVEL_HIGH>;
 				reg = <0x0f123000 0x1000>;
 				status = "disabled";
 			};
 
-			frame@0f124000 {
+			frame@f124000 {
 				frame-number = <2>;
 				interrupts = <GIC_SPI 10 IRQ_TYPE_LEVEL_HIGH>;
 				reg = <0x0f124000 0x1000>;
@@ -548,7 +553,7 @@
 		intc: interrupt-controller@f200000 {
 			compatible = "arm,gic-v3";
 			reg = <0x0f200000 0x20000>,
-				<0x0f300000 0x100000>;
+			      <0x0f300000 0x100000>;
 			#interrupt-cells = <3>;
 			interrupt-controller;
 			interrupts = <GIC_PPI 9 IRQ_TYPE_LEVEL_HIGH>;
@@ -558,9 +563,9 @@
 	timer {
 		compatible = "arm,armv8-timer";
 		interrupts = <GIC_PPI 1 0xf08
-				GIC_PPI 2 0xf08
-				GIC_PPI 3 0xf08
-				GIC_PPI 0 0xf08>;
+			      GIC_PPI 2 0xf08
+			      GIC_PPI 3 0xf08
+			      GIC_PPI 0 0xf08>;
 		clock-frequency = <19200000>;
 	};
 };
diff --git a/arch/arm64/boot/dts/qcom/sm6350-sony-xperia-lena-pdx213.dts b/arch/arm64/boot/dts/qcom/sm6350-sony-xperia-lena-pdx213.dts
new file mode 100644
index 000000000000..36911b9a5c04
--- /dev/null
+++ b/arch/arm64/boot/dts/qcom/sm6350-sony-xperia-lena-pdx213.dts
@@ -0,0 +1,58 @@
+// SPDX-License-Identifier: BSD-3-Clause
+/*
+ * Copyright (c) 2021, Konrad Dybcio <konrad.dybcio@somainline.org>
+ */
+/dts-v1/;
+
+#include "sm6350.dtsi"
+
+/ {
+	model = "Sony Xperia 10 III";
+	compatible = "sony,pdx213", "qcom,sm6350";
+	chassis-type = "handset";
+	qcom,msm-id = <434 0x10000>, <459 0x10000>;
+	qcom,board-id = <0x1000B 0>;
+
+	chosen {
+		#address-cells = <2>;
+		#size-cells = <2>;
+		ranges;
+
+		framebuffer: framebuffer@a0000000 {
+			compatible = "simple-framebuffer";
+			reg = <0 0xa0000000 0 0x2300000>;
+			width = <1080>;
+			height = <2520>;
+			stride = <(1080 * 4)>;
+			format = "a8r8g8b8";
+			clocks = <&gcc GCC_DISP_AXI_CLK>;
+		};
+	};
+};
+
+&sdhc_2 {
+	status = "okay";
+
+	cd-gpios = <&tlmm 94 GPIO_ACTIVE_HIGH>;
+};
+
+&tlmm {
+	gpio-reserved-ranges = <13 4>, <45 2>, <56 2>;
+};
+
+&usb_1 {
+	status = "okay";
+};
+
+&usb_1_dwc3 {
+	maximum-speed = "super-speed";
+	dr_mode = "peripheral";
+};
+
+&usb_1_hsphy {
+	status = "okay";
+};
+
+&usb_1_qmpphy {
+	status = "okay";
+};
diff --git a/arch/arm64/boot/dts/qcom/sm6350.dtsi b/arch/arm64/boot/dts/qcom/sm6350.dtsi
new file mode 100644
index 000000000000..973e18fe3b67
--- /dev/null
+++ b/arch/arm64/boot/dts/qcom/sm6350.dtsi
@@ -0,0 +1,965 @@
+// SPDX-License-Identifier: BSD-3-Clause
+/*
+ * Copyright (c) 2021, Konrad Dybcio <konrad.dybcio@somainline.org>
+ */
+
+#include <dt-bindings/clock/qcom,gcc-sm6350.h>
+#include <dt-bindings/clock/qcom,rpmh.h>
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/interrupt-controller/arm-gic.h>
+#include <dt-bindings/mailbox/qcom-ipcc.h>
+#include <dt-bindings/power/qcom-rpmpd.h>
+#include <dt-bindings/soc/qcom,rpmh-rsc.h>
+
+/ {
+	interrupt-parent = <&intc>;
+	#address-cells = <2>;
+	#size-cells = <2>;
+
+	clocks {
+		xo_board: xo-board {
+			compatible = "fixed-clock";
+			#clock-cells = <0>;
+			clock-frequency = <76800000>;
+			clock-output-names = "xo_board";
+		};
+
+		sleep_clk: sleep-clk {
+			compatible = "fixed-clock";
+			clock-frequency = <32764>;
+			#clock-cells = <0>;
+		};
+	};
+
+	cpus {
+		#address-cells = <2>;
+		#size-cells = <0>;
+
+		CPU0: cpu@0 {
+			device_type = "cpu";
+			compatible = "qcom,kryo560";
+			reg = <0x0 0x0>;
+			enable-method = "psci";
+			capacity-dmips-mhz = <1024>;
+			dynamic-power-coefficient = <100>;
+			next-level-cache = <&L2_0>;
+			qcom,freq-domain = <&cpufreq_hw 0>;
+			#cooling-cells = <2>;
+			L2_0: l2-cache {
+				compatible = "cache";
+				next-level-cache = <&L3_0>;
+				L3_0: l3-cache {
+					compatible = "cache";
+				};
+			};
+		};
+
+		CPU1: cpu@100 {
+			device_type = "cpu";
+			compatible = "qcom,kryo560";
+			reg = <0x0 0x100>;
+			enable-method = "psci";
+			capacity-dmips-mhz = <1024>;
+			dynamic-power-coefficient = <100>;
+			next-level-cache = <&L2_100>;
+			qcom,freq-domain = <&cpufreq_hw 0>;
+			#cooling-cells = <2>;
+			L2_100: l2-cache {
+				compatible = "cache";
+				next-level-cache = <&L3_0>;
+			};
+		};
+
+		CPU2: cpu@200 {
+			device_type = "cpu";
+			compatible = "qcom,kryo560";
+			reg = <0x0 0x200>;
+			enable-method = "psci";
+			capacity-dmips-mhz = <1024>;
+			dynamic-power-coefficient = <100>;
+			next-level-cache = <&L2_200>;
+			qcom,freq-domain = <&cpufreq_hw 0>;
+			#cooling-cells = <2>;
+			L2_200: l2-cache {
+				compatible = "cache";
+				next-level-cache = <&L3_0>;
+			};
+		};
+
+		CPU3: cpu@300 {
+			device_type = "cpu";
+			compatible = "qcom,kryo560";
+			reg = <0x0 0x300>;
+			enable-method = "psci";
+			capacity-dmips-mhz = <1024>;
+			dynamic-power-coefficient = <100>;
+			next-level-cache = <&L2_300>;
+			qcom,freq-domain = <&cpufreq_hw 0>;
+			#cooling-cells = <2>;
+			L2_300: l2-cache {
+				compatible = "cache";
+				next-level-cache = <&L3_0>;
+			};
+		};
+
+		CPU4: cpu@400 {
+			device_type = "cpu";
+			compatible = "qcom,kryo560";
+			reg = <0x0 0x400>;
+			enable-method = "psci";
+			capacity-dmips-mhz = <1024>;
+			dynamic-power-coefficient = <100>;
+			next-level-cache = <&L2_400>;
+			qcom,freq-domain = <&cpufreq_hw 0>;
+			#cooling-cells = <2>;
+			L2_400: l2-cache {
+				compatible = "cache";
+				next-level-cache = <&L3_0>;
+			};
+		};
+
+		CPU5: cpu@500 {
+			device_type = "cpu";
+			compatible = "qcom,kryo560";
+			reg = <0x0 0x500>;
+			enable-method = "psci";
+			capacity-dmips-mhz = <1024>;
+			dynamic-power-coefficient = <100>;
+			next-level-cache = <&L2_500>;
+			qcom,freq-domain = <&cpufreq_hw 0>;
+			#cooling-cells = <2>;
+			L2_500: l2-cache {
+				compatible = "cache";
+				next-level-cache = <&L3_0>;
+			};
+
+		};
+
+		CPU6: cpu@600 {
+			device_type = "cpu";
+			compatible = "qcom,kryo560";
+			reg = <0x0 0x600>;
+			enable-method = "psci";
+			capacity-dmips-mhz = <1894>;
+			dynamic-power-coefficient = <703>;
+			next-level-cache = <&L2_600>;
+			qcom,freq-domain = <&cpufreq_hw 1>;
+			#cooling-cells = <2>;
+			L2_600: l2-cache {
+				compatible = "cache";
+				next-level-cache = <&L3_0>;
+			};
+		};
+
+		CPU7: cpu@700 {
+			device_type = "cpu";
+			compatible = "qcom,kryo560";
+			reg = <0x0 0x700>;
+			enable-method = "psci";
+			capacity-dmips-mhz = <1894>;
+			dynamic-power-coefficient = <703>;
+			next-level-cache = <&L2_700>;
+			qcom,freq-domain = <&cpufreq_hw 1>;
+			#cooling-cells = <2>;
+			L2_700: l2-cache {
+				compatible = "cache";
+				next-level-cache = <&L3_0>;
+			};
+		};
+
+		cpu-map {
+			cluster0 {
+				core0 {
+					cpu = <&CPU0>;
+				};
+
+				core1 {
+					cpu = <&CPU1>;
+				};
+
+				core2 {
+					cpu = <&CPU2>;
+				};
+
+				core3 {
+					cpu = <&CPU3>;
+				};
+
+				core4 {
+					cpu = <&CPU4>;
+				};
+
+				core5 {
+					cpu = <&CPU5>;
+				};
+
+				core6 {
+					cpu = <&CPU6>;
+				};
+
+				core7 {
+					cpu = <&CPU7>;
+				};
+			};
+		};
+	};
+
+	firmware {
+		scm: scm {
+			compatible = "qcom,scm-sm6350", "qcom,scm";
+			#reset-cells = <1>;
+		};
+	};
+
+	memory@80000000 {
+		device_type = "memory";
+		/* We expect the bootloader to fill in the size */
+		reg = <0x0 0x80000000 0x0 0x0>;
+	};
+
+	pmu {
+		compatible = "arm,armv8-pmuv3";
+		interrupts = <GIC_PPI 5 IRQ_TYPE_LEVEL_LOW>;
+	};
+
+	psci {
+		compatible = "arm,psci-1.0";
+		method = "smc";
+	};
+
+	reserved_memory: reserved-memory {
+		#address-cells = <2>;
+		#size-cells = <2>;
+		ranges;
+
+		hyp_mem: memory@80000000 {
+			reg = <0 0x80000000 0 0x600000>;
+			no-map;
+		};
+
+		xbl_aop_mem: memory@80700000 {
+			reg = <0 0x80700000 0 0x160000>;
+			no-map;
+		};
+
+		cmd_db: memory@80860000 {
+			compatible = "qcom,cmd-db";
+			reg = <0 0x80860000 0 0x20000>;
+			no-map;
+		};
+
+		sec_apps_mem: memory@808ff000 {
+			reg = <0 0x808ff000 0 0x1000>;
+			no-map;
+		};
+
+		smem_mem: memory@80900000 {
+			reg = <0 0x80900000 0 0x200000>;
+			no-map;
+		};
+
+		cdsp_sec_mem: memory@80b00000 {
+			reg = <0 0x80b00000 0 0x1e00000>;
+			no-map;
+		};
+
+		pil_camera_mem: memory@86000000 {
+			reg = <0 0x86000000 0 0x500000>;
+			no-map;
+		};
+
+		pil_npu_mem: memory@86500000 {
+			reg = <0 0x86500000 0 0x500000>;
+			no-map;
+		};
+
+		pil_video_mem: memory@86a00000 {
+			reg = <0 0x86a00000 0 0x500000>;
+			no-map;
+		};
+
+		pil_cdsp_mem: memory@86f00000 {
+			reg = <0 0x86f00000 0 0x1e00000>;
+			no-map;
+		};
+
+		pil_adsp_mem: memory@88d00000 {
+			reg = <0 0x88d00000 0 0x2800000>;
+			no-map;
+		};
+
+		wlan_fw_mem: memory@8b500000 {
+			reg = <0 0x8b500000 0 0x200000>;
+			no-map;
+		};
+
+		pil_ipa_fw_mem: memory@8b700000 {
+			reg = <0 0x8b700000 0 0x10000>;
+			no-map;
+		};
+
+		pil_ipa_gsi_mem: memory@8b710000 {
+			reg = <0 0x8b710000 0 0x5400>;
+			no-map;
+		};
+
+		pil_gpu_mem: memory@8b715400 {
+			reg = <0 0x8b715400 0 0x2000>;
+			no-map;
+		};
+
+		pil_modem_mem: memory@8b800000 {
+			reg = <0 0x8b800000 0 0xf800000>;
+			no-map;
+		};
+
+		cont_splash_memory: memory@a0000000 {
+			reg = <0 0xa0000000 0 0x2300000>;
+			no-map;
+		};
+
+		dfps_data_memory: memory@a2300000 {
+			reg = <0 0xa2300000 0 0x100000>;
+			no-map;
+		};
+
+		removed_region: memory@c0000000 {
+			reg = <0 0xc0000000 0 0x3900000>;
+			no-map;
+		};
+
+		debug_region: memory@ffb00000 {
+			reg = <0 0xffb00000 0 0xc0000>;
+			no-map;
+		};
+
+		last_log_region: memory@ffbc0000 {
+			reg = <0 0xffbc0000 0 0x40000>;
+			no-map;
+		};
+
+		ramoops: ramoops@ffc00000 {
+			compatible = "removed-dma-pool", "ramoops";
+			reg = <0 0xffc00000 0 0x00100000>;
+			record-size = <0x1000>;
+			console-size = <0x40000>;
+			ftrace-size = <0x0>;
+			msg-size = <0x20000 0x20000>;
+			cc-size = <0x0>;
+			no-map;
+		};
+
+		cmdline_region: memory@ffd00000 {
+			reg = <0 0xffd00000 0 0x1000>;
+			no-map;
+		};
+	};
+
+	smem {
+		compatible = "qcom,smem";
+		memory-region = <&smem_mem>;
+		hwlocks = <&tcsr_mutex 3>;
+	};
+
+	soc: soc@0 {
+		#address-cells = <2>;
+		#size-cells = <2>;
+		ranges = <0 0 0 0 0x10 0>;
+		dma-ranges = <0 0 0 0 0x10 0>;
+		compatible = "simple-bus";
+
+		gcc: clock-controller@100000 {
+			compatible = "qcom,gcc-sm6350";
+			reg = <0 0x00100000 0 0x1f0000>;
+			#clock-cells = <1>;
+			#reset-cells = <1>;
+			#power-domain-cells = <1>;
+			clock-names = "bi_tcxo",
+				      "bi_tcxo_ao",
+				      "sleep_clk";
+			clocks = <&rpmhcc RPMH_CXO_CLK>,
+				 <&rpmhcc RPMH_CXO_CLK_A>,
+				 <&sleep_clk>;
+		};
+
+		ipcc: mailbox@408000 {
+			compatible = "qcom,sm6350-ipcc", "qcom,ipcc";
+			reg = <0 0x00408000 0 0x1000>;
+			interrupts = <GIC_SPI 228 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-controller;
+			#interrupt-cells = <3>;
+			#mbox-cells = <2>;
+		};
+
+		rng: rng@793000 {
+			compatible = "qcom,prng-ee";
+			reg = <0 0x00793000 0 0x1000>;
+			clocks = <&gcc GCC_PRNG_AHB_CLK>;
+			clock-names = "core";
+		};
+
+		sdhc_1: sdhci@7c4000 {
+			compatible = "qcom,sm6350-sdhci", "qcom,sdhci-msm-v5";
+			reg = <0 0x007c4000 0 0x1000>,
+				<0 0x007c5000 0 0x1000>,
+				<0 0x007c8000 0 0x8000>;
+			reg-names = "hc", "cqhci", "ice";
+
+			interrupts = <GIC_SPI 641 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 644 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "hc_irq", "pwr_irq";
+
+			clocks = <&gcc GCC_SDCC1_AHB_CLK>,
+				 <&gcc GCC_SDCC1_APPS_CLK>,
+				 <&rpmhcc RPMH_CXO_CLK>;
+			clock-names = "iface", "core", "xo";
+			qcom,dll-config = <0x000f642c>;
+			qcom,ddr-config = <0x80040868>;
+			power-domains = <&rpmhpd 0>;
+			operating-points-v2 = <&sdhc1_opp_table>;
+			bus-width = <8>;
+			non-removable;
+			supports-cqe;
+
+			status = "disabled";
+
+			sdhc1_opp_table: sdhc1-opp-table {
+				compatible = "operating-points-v2";
+
+				opp-19200000 {
+					opp-hz = /bits/ 64 <19200000>;
+					required-opps = <&rpmhpd_opp_min_svs>;
+				};
+
+				opp-100000000 {
+					opp-hz = /bits/ 64 <100000000>;
+					required-opps = <&rpmhpd_opp_low_svs>;
+				};
+
+				opp-384000000 {
+					opp-hz = /bits/ 64 <384000000>;
+					required-opps = <&rpmhpd_opp_svs_l1>;
+				};
+			};
+		};
+
+		qupv3_id_1: geniqup@9c0000 {
+			compatible = "qcom,geni-se-qup";
+			reg = <0x0 0x9c0000 0x0 0x2000>;
+			clock-names = "m-ahb", "s-ahb";
+			clocks = <&gcc GCC_QUPV3_WRAP_1_M_AHB_CLK>,
+				 <&gcc GCC_QUPV3_WRAP_1_S_AHB_CLK>;
+			#address-cells = <2>;
+			#size-cells = <2>;
+			iommus = <&apps_smmu 0x4c3 0x0>;
+			ranges;
+			status = "disabled";
+
+			uart2: serial@98c000 {
+				compatible = "qcom,geni-debug-uart";
+				reg = <0 0x98c000 0 0x4000>;
+				clock-names = "se";
+				clocks = <&gcc GCC_QUPV3_WRAP1_S3_CLK>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&qup_uart2_default>;
+				interrupts = <GIC_SPI 356 IRQ_TYPE_LEVEL_HIGH>;
+				status = "disabled";
+			};
+		};
+
+		tcsr_mutex: hwlock@1f40000 {
+			compatible = "qcom,tcsr-mutex";
+			reg = <0x0 0x01f40000 0x0 0x40000>;
+			#hwlock-cells = <1>;
+		};
+
+		sdhc_2: sdhci@8804000 {
+			compatible = "qcom,sm6350-sdhci", "qcom,sdhci-msm-v5";
+			reg = <0 0x08804000 0 0x1000>;
+
+			interrupts = <GIC_SPI 204 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 222 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "hc_irq", "pwr_irq";
+
+			clocks = <&gcc GCC_SDCC2_AHB_CLK>,
+				 <&gcc GCC_SDCC2_APPS_CLK>,
+				 <&rpmhcc RPMH_CXO_CLK>;
+			clock-names = "iface", "core", "xo";
+			qcom,dll-config = <0x0007642c>;
+			qcom,ddr-config = <0x80040868>;
+			power-domains = <&rpmhpd 0>;
+			operating-points-v2 = <&sdhc2_opp_table>;
+			bus-width = <4>;
+
+			status = "disabled";
+
+			sdhc2_opp_table: sdhc2-opp-table {
+				compatible = "operating-points-v2";
+
+				opp-100000000 {
+					opp-hz = /bits/ 64 <100000000>;
+					required-opps = <&rpmhpd_opp_svs_l1>;
+				};
+
+				opp-202000000 {
+					opp-hz = /bits/ 64 <202000000>;
+					required-opps = <&rpmhpd_opp_nom>;
+				};
+			};
+		};
+
+		usb_1_hsphy: phy@88e3000 {
+			compatible = "qcom,sm6350-qusb2-phy", "qcom,qusb2-v2-phy";
+			reg = <0 0x088e3000 0 0x400>;
+			status = "disabled";
+			#phy-cells = <0>;
+
+			clocks = <&xo_board>, <&rpmhcc RPMH_CXO_CLK>;
+			clock-names = "cfg_ahb", "ref";
+
+			resets = <&gcc GCC_QUSB2PHY_PRIM_BCR>;
+		};
+
+		usb_1_qmpphy: phy@88e9000 {
+			compatible = "qcom,sc7180-qmp-usb3-dp-phy";
+			reg = <0 0x088e9000 0 0x200>,
+			      <0 0x088e8000 0 0x40>,
+			      <0 0x088ea000 0 0x200>;
+			status = "disabled";
+			#address-cells = <2>;
+			#size-cells = <2>;
+			ranges;
+
+			clocks = <&gcc GCC_USB3_PRIM_PHY_AUX_CLK>,
+				 <&rpmhcc RPMH_QLINK_CLK>,
+				 <&gcc GCC_USB3_PRIM_PHY_COM_AUX_CLK>,
+				 <&xo_board>;
+			clock-names = "aux", "ref", "com_aux", "cfg_ahb";
+
+			resets = <&gcc GCC_USB3_DP_PHY_PRIM_BCR>,
+				 <&gcc GCC_USB3_PHY_PRIM_BCR>;
+			reset-names = "phy", "common";
+
+			usb_1_ssphy: usb3-phy@88e9200 {
+				reg = <0 0x088e9200 0 0x200>,
+				      <0 0x088e9400 0 0x200>,
+				      <0 0x088e9c00 0 0x400>,
+				      <0 0x088e9600 0 0x200>,
+				      <0 0x088e9800 0 0x200>,
+				      <0 0x088e9a00 0 0x100>;
+				#clock-cells = <0>;
+				#phy-cells = <0>;
+				clocks = <&gcc GCC_USB3_PRIM_PHY_PIPE_CLK>;
+				clock-names = "pipe0";
+				clock-output-names = "usb3_phy_pipe_clk_src";
+			};
+
+			dp_phy: dp-phy@88ea200 {
+				reg = <0 0x088ea200 0 0x200>,
+				      <0 0x088ea400 0 0x200>,
+				      <0 0x088eac00 0 0x400>,
+				      <0 0x088ea600 0 0x200>,
+				      <0 0x088ea800 0 0x200>,
+				      <0 0x088eaa00 0 0x100>;
+				#phy-cells = <0>;
+				#clock-cells = <1>;
+				clocks = <&gcc GCC_USB3_PRIM_PHY_PIPE_CLK>;
+				clock-names = "pipe0";
+				clock-output-names = "usb3_phy_pipe_clk_src";
+			};
+		};
+
+		system-cache-controller@9200000 {
+			compatible = "qcom,sm6350-llcc";
+			reg = <0 0x09200000 0 0x50000>, <0 0x09600000 0 0x50000>;
+			reg-names = "llcc_base", "llcc_broadcast_base";
+		};
+
+		usb_1: usb@a6f8800 {
+			compatible = "qcom,sm6350-dwc3", "qcom,dwc3";
+			reg = <0 0x0a6f8800 0 0x400>;
+			status = "disabled";
+			#address-cells = <2>;
+			#size-cells = <2>;
+			ranges;
+
+			clocks = <&gcc GCC_CFG_NOC_USB3_PRIM_AXI_CLK>,
+				 <&gcc GCC_USB30_PRIM_MASTER_CLK>,
+				 <&gcc GCC_AGGRE_USB3_PRIM_AXI_CLK>,
+				 <&gcc GCC_USB30_PRIM_MOCK_UTMI_CLK>,
+				 <&gcc GCC_USB30_PRIM_SLEEP_CLK>;
+			clock-names = "cfg_noc", "core", "iface", "mock_utmi",
+				      "sleep";
+
+			interrupts-extended = <&intc GIC_SPI 130 IRQ_TYPE_LEVEL_HIGH>,
+					      <&pdc 14 IRQ_TYPE_EDGE_BOTH>,
+					      <&pdc 15 IRQ_TYPE_EDGE_BOTH>,
+					      <&pdc 17 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "hs_phy_irq", "dp_hs_phy_irq",
+					  "dm_hs_phy_irq", "ss_phy_irq";
+
+			power-domains = <&gcc USB30_PRIM_GDSC>;
+
+			resets = <&gcc GCC_USB30_PRIM_BCR>;
+
+			usb_1_dwc3: usb@a600000 {
+				compatible = "snps,dwc3";
+				reg = <0 0x0a600000 0 0xcd00>;
+				interrupts = <GIC_SPI 133 IRQ_TYPE_LEVEL_HIGH>;
+				iommus = <&apps_smmu 0x540 0x0>;
+				snps,dis_u2_susphy_quirk;
+				snps,dis_enblslpm_quirk;
+				snps,has-lpm-erratum;
+				snps,hird-threshold = /bits/ 8 <0x10>;
+				phys = <&usb_1_hsphy>, <&usb_1_ssphy>;
+				phy-names = "usb2-phy", "usb3-phy";
+			};
+		};
+
+		pdc: interrupt-controller@b220000 {
+			compatible = "qcom,sm6350-pdc", "qcom,pdc";
+			reg = <0 0x0b220000 0 0x30000>, <0 0x17c000f0 0 0x64>;
+			qcom,pdc-ranges = <0 480 94>, <94 609 31>,
+					  <125 63 1>, <126 655 12>, <138 139 15>;
+			#interrupt-cells = <2>;
+			interrupt-parent = <&intc>;
+			interrupt-controller;
+		};
+
+		tsens0: thermal-sensor@c263000 {
+			compatible = "qcom,sm6350-tsens", "qcom,tsens-v2";
+			reg = <0 0x0c263000 0 0x1ff>, /* TM */
+			      <0 0x0c222000 0 0x8>; /* SROT */
+			#qcom,sensors = <16>;
+			interrupts = <&pdc 26 IRQ_TYPE_LEVEL_HIGH>,
+				     <&pdc 28 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "uplow", "critical";
+			#thermal-sensor-cells = <1>;
+		};
+
+		tsens1: thermal-sensor@c265000 {
+			compatible = "qcom,sm6350-tsens", "qcom,tsens-v2";
+			reg = <0 0x0c265000 0 0x1ff>, /* TM */
+			      <0 0x0c223000 0 0x8>; /* SROT */
+			#qcom,sensors = <16>;
+			interrupts = <&pdc 27 IRQ_TYPE_LEVEL_HIGH>,
+				     <&pdc 29 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "uplow", "critical";
+			#thermal-sensor-cells = <1>;
+		};
+
+		aoss_qmp: power-controller@c300000 {
+			compatible = "qcom,sm6350-aoss-qmp", "qcom,aoss-qmp";
+			reg = <0 0x0c300000 0 0x1000>;
+			interrupts-extended = <&ipcc IPCC_CLIENT_AOP IPCC_MPROC_SIGNAL_GLINK_QMP
+						     IRQ_TYPE_EDGE_RISING>;
+			mboxes = <&ipcc IPCC_CLIENT_AOP IPCC_MPROC_SIGNAL_GLINK_QMP>;
+
+			#clock-cells = <0>;
+			#power-domain-cells = <1>;
+		};
+
+		spmi_bus: spmi@c440000 {
+			compatible = "qcom,spmi-pmic-arb";
+			reg = <0 0xc440000 0 0x1100>,
+			      <0 0xc600000 0 0x2000000>,
+			      <0 0xe600000 0 0x100000>,
+			      <0 0xe700000 0 0xa0000>,
+			      <0 0xc40a000 0 0x26000>;
+			reg-names = "core", "chnls", "obsrvr", "intr", "cnfg";
+			interrupt-names = "periph_irq";
+			interrupts-extended = <&pdc 1 IRQ_TYPE_LEVEL_HIGH>;
+			qcom,ee = <0>;
+			qcom,channel = <0>;
+			#address-cells = <2>;
+			#size-cells = <0>;
+			interrupt-controller;
+			#interrupt-cells = <4>;
+		};
+
+		tlmm: pinctrl@f100000 {
+			compatible = "qcom,sm6350-tlmm";
+			reg = <0 0x0f100000 0 0x300000>;
+			interrupts = <GIC_SPI 208 IRQ_TYPE_LEVEL_HIGH>,
+					<GIC_SPI 209 IRQ_TYPE_LEVEL_HIGH>,
+					<GIC_SPI 210 IRQ_TYPE_LEVEL_HIGH>,
+					<GIC_SPI 211 IRQ_TYPE_LEVEL_HIGH>,
+					<GIC_SPI 212 IRQ_TYPE_LEVEL_HIGH>,
+					<GIC_SPI 213 IRQ_TYPE_LEVEL_HIGH>,
+					<GIC_SPI 214 IRQ_TYPE_LEVEL_HIGH>,
+					<GIC_SPI 215 IRQ_TYPE_LEVEL_HIGH>,
+					<GIC_SPI 216 IRQ_TYPE_LEVEL_HIGH>;
+			gpio-controller;
+			#gpio-cells = <2>;
+			interrupt-controller;
+			#interrupt-cells = <2>;
+			gpio-ranges = <&tlmm 0 0 157>;
+
+			qup_uart2_default: qup-uart2-default {
+				pins = "gpio25", "gpio26";
+				function = "qup13_f2";
+				drive-strength = <2>;
+				bias-disable;
+			};
+		};
+
+		apps_smmu: iommu@15000000 {
+			compatible = "qcom,sm6350-smmu-500", "arm,mmu-500";
+			reg = <0 0x15000000 0 0x100000>;
+			#iommu-cells = <2>;
+			#global-interrupts = <1>;
+			interrupts = <GIC_SPI 65 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 95 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 96 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 97 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 98 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 99 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 100 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 101 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 102 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 103 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 104 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 105 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 106 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 107 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 108 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 109 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 110 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 111 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 112 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 113 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 114 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 115 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 116 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 117 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 118 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 181 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 182 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 183 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 184 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 185 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 186 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 187 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 188 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 189 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 190 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 191 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 192 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 315 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 316 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 317 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 318 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 319 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 320 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 321 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 322 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 323 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 324 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 325 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 326 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 327 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 328 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 329 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 330 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 331 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 332 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 333 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 334 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 335 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 336 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 337 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 338 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 339 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 340 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 341 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 342 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 343 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 344 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 345 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 401 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 402 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 403 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 404 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 405 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 406 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 407 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 408 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 409 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 410 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 411 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 412 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 413 IRQ_TYPE_LEVEL_HIGH>;
+		};
+
+		intc: interrupt-controller@17a00000 {
+			compatible = "arm,gic-v3";
+			#interrupt-cells = <3>;
+			interrupt-controller;
+			reg = <0x0 0x17a00000 0x0 0x10000>,     /* GICD */
+			      <0x0 0x17a60000 0x0 0x100000>;    /* GICR * 8 */
+			interrupts = <GIC_PPI 8 IRQ_TYPE_LEVEL_HIGH>;
+		};
+
+		watchdog@17c10000 {
+			compatible = "qcom,apss-wdt-sm6350", "qcom,kpss-wdt";
+			reg = <0 0x17c10000 0 0x1000>;
+			clocks = <&sleep_clk>;
+			interrupts = <GIC_SPI 0 IRQ_TYPE_LEVEL_HIGH>;
+		};
+
+		timer@17c20000 {
+			compatible = "arm,armv7-timer-mem";
+			reg = <0x0 0x17c20000 0x0 0x1000>;
+			clock-frequency = <19200000>;
+			#address-cells = <2>;
+			#size-cells = <2>;
+			ranges;
+
+			frame@17c21000 {
+				frame-number = <0>;
+				interrupts = <GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>,
+					     <GIC_SPI 6 IRQ_TYPE_LEVEL_HIGH>;
+				reg = <0x0 0x17c21000 0x0 0x1000>,
+				      <0x0 0x17c22000 0x0 0x1000>;
+			};
+
+			frame@17c23000 {
+				frame-number = <1>;
+				interrupts = <GIC_SPI 9 IRQ_TYPE_LEVEL_HIGH>;
+				reg = <0x0 0x17c23000 0x0 0x1000>;
+				status = "disabled";
+			};
+
+			frame@17c25000 {
+				frame-number = <2>;
+				interrupts = <GIC_SPI 10 IRQ_TYPE_LEVEL_HIGH>;
+				reg = <0x0 0x17c25000 0x0 0x1000>;
+				status = "disabled";
+			};
+
+			frame@17c27000 {
+				frame-number = <3>;
+				interrupts = <GIC_SPI 11 IRQ_TYPE_LEVEL_HIGH>;
+				reg = <0x0 0x17c27000 0x0 0x1000>;
+				status = "disabled";
+			};
+
+			frame@17c29000 {
+				frame-number = <4>;
+				interrupts = <GIC_SPI 12 IRQ_TYPE_LEVEL_HIGH>;
+				reg = <0x0 0x17c29000 0x0 0x1000>;
+				status = "disabled";
+			};
+
+			frame@17c2b000 {
+				frame-number = <5>;
+				interrupts = <GIC_SPI 13 IRQ_TYPE_LEVEL_HIGH>;
+				reg = <0x0 0x17c2b000 0x0 0x1000>;
+				status = "disabled";
+			};
+
+			frame@17c2d000 {
+				frame-number = <6>;
+				interrupts = <GIC_SPI 14 IRQ_TYPE_LEVEL_HIGH>;
+				reg = <0x0 0x17c2d000 0x0 0x1000>;
+				status = "disabled";
+			};
+		};
+
+		apps_rsc: rsc@18200000 {
+			compatible = "qcom,rpmh-rsc";
+			label = "apps_rsc";
+			reg = <0x0 0x18200000 0x0 0x10000>,
+				<0x0 0x18210000 0x0 0x10000>,
+				<0x0 0x18220000 0x0 0x10000>;
+			reg-names = "drv-0", "drv-1", "drv-2";
+			interrupts = <GIC_SPI 3 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 4 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 5 IRQ_TYPE_LEVEL_HIGH>;
+			qcom,tcs-offset = <0xd00>;
+			qcom,drv-id = <2>;
+			qcom,tcs-config = <ACTIVE_TCS 2>, <SLEEP_TCS 3>,
+					  <WAKE_TCS 3>, <CONTROL_TCS 1>;
+
+			rpmhcc: clock-controller {
+				compatible = "qcom,sm6350-rpmh-clk";
+				#clock-cells = <1>;
+				clock-names = "xo";
+				clocks = <&xo_board>;
+			};
+
+			rpmhpd: power-controller {
+				compatible = "qcom,sm6350-rpmhpd";
+				#power-domain-cells = <1>;
+				operating-points-v2 = <&rpmhpd_opp_table>;
+
+				rpmhpd_opp_table: opp-table {
+					compatible = "operating-points-v2";
+
+					rpmhpd_opp_ret: opp1 {
+						opp-level = <RPMH_REGULATOR_LEVEL_RETENTION>;
+					};
+
+					rpmhpd_opp_min_svs: opp2 {
+						opp-level = <RPMH_REGULATOR_LEVEL_MIN_SVS>;
+					};
+
+					rpmhpd_opp_low_svs: opp3 {
+						opp-level = <RPMH_REGULATOR_LEVEL_LOW_SVS>;
+					};
+
+					rpmhpd_opp_svs: opp4 {
+						opp-level = <RPMH_REGULATOR_LEVEL_SVS>;
+					};
+
+					rpmhpd_opp_svs_l1: opp5 {
+						opp-level = <RPMH_REGULATOR_LEVEL_SVS_L1>;
+					};
+
+					rpmhpd_opp_nom: opp6 {
+						opp-level = <RPMH_REGULATOR_LEVEL_NOM>;
+					};
+
+					rpmhpd_opp_nom_l1: opp7 {
+						opp-level = <RPMH_REGULATOR_LEVEL_NOM_L1>;
+					};
+
+					rpmhpd_opp_nom_l2: opp8 {
+						opp-level = <RPMH_REGULATOR_LEVEL_NOM_L2>;
+					};
+
+					rpmhpd_opp_turbo: opp9 {
+						opp-level = <RPMH_REGULATOR_LEVEL_TURBO>;
+					};
+
+					rpmhpd_opp_turbo_l1: opp10 {
+						opp-level = <RPMH_REGULATOR_LEVEL_TURBO_L1>;
+					};
+				};
+			};
+
+			apps_bcm_voter: bcm_voter {
+				compatible = "qcom,bcm-voter";
+			};
+		};
+
+		cpufreq_hw: cpufreq@18323000 {
+			compatible = "qcom,cpufreq-hw";
+			reg = <0 0x18323000 0 0x1000>, <0 0x18325800 0 0x1000>;
+			reg-names = "freq-domain0", "freq-domain1";
+			clocks = <&rpmhcc RPMH_CXO_CLK>, <&gcc GPLL0>;
+			clock-names = "xo", "alternate";
+
+			#freq-domain-cells = <1>;
+		};
+	};
+
+	timer {
+		compatible = "arm,armv8-timer";
+		clock-frequency = <19200000>;
+		interrupts = <GIC_PPI 1 (GIC_CPU_MASK_SIMPLE(8) | IRQ_TYPE_LEVEL_LOW)>,
+			     <GIC_PPI 2 (GIC_CPU_MASK_SIMPLE(8) | IRQ_TYPE_LEVEL_LOW)>,
+			     <GIC_PPI 3 (GIC_CPU_MASK_SIMPLE(8) | IRQ_TYPE_LEVEL_LOW)>,
+			     <GIC_PPI 0 (GIC_CPU_MASK_SIMPLE(8) | IRQ_TYPE_LEVEL_LOW)>;
+	};
+};
diff --git a/arch/arm64/boot/dts/qcom/sm7225-fairphone-fp4.dts b/arch/arm64/boot/dts/qcom/sm7225-fairphone-fp4.dts
new file mode 100644
index 000000000000..8d6fd22873e0
--- /dev/null
+++ b/arch/arm64/boot/dts/qcom/sm7225-fairphone-fp4.dts
@@ -0,0 +1,320 @@
+// SPDX-License-Identifier: BSD-3-Clause
+/*
+ * Copyright (c) 2021, Luca Weiss <luca@z3ntu.xyz>
+ */
+
+/dts-v1/;
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/pinctrl/qcom,pmic-gpio.h>
+#include <dt-bindings/regulator/qcom,rpmh-regulator.h>
+#include "sm7225.dtsi"
+#include "pm6350.dtsi"
+
+/ {
+	model = "Fairphone 4";
+	compatible = "fairphone,fp4", "qcom,sm7225";
+
+	/* required for bootloader to select correct board */
+	qcom,msm-id = <434 0x10000>, <459 0x10000>;
+	qcom,board-id = <8 32>;
+
+	aliases {
+		serial0 = &uart2;
+	};
+
+	chosen {
+		#address-cells = <2>;
+		#size-cells = <2>;
+		ranges;
+
+		stdout-path = "serial0:115200n8";
+
+		framebuffer0: framebuffer@a000000 {
+			compatible = "simple-framebuffer";
+			reg = <0 0xa0000000 0 (2340 * 1080 * 4)>;
+			width = <1080>;
+			height = <2340>;
+			stride = <(1080 * 4)>;
+			format = "a8r8g8b8";
+		};
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+		pinctrl-names = "default";
+		pinctrl-0 = <&gpio_keys_pin>;
+
+		volume-up {
+			label = "volume_up";
+			linux,code = <KEY_VOLUMEUP>;
+			gpios = <&pm6350_gpios 2 GPIO_ACTIVE_LOW>;
+		};
+	};
+};
+
+&apps_rsc {
+	pm6350-rpmh-regulators {
+		compatible = "qcom,pm6350-rpmh-regulators";
+		qcom,pmic-id = "a";
+
+		vreg_s1a: smps1 {
+			regulator-min-microvolt = <1000000>;
+			regulator-max-microvolt = <1200000>;
+		};
+
+		vreg_s2a: smps2 {
+			regulator-min-microvolt = <1503000>;
+			regulator-max-microvolt = <2048000>;
+		};
+
+		vreg_l2a: ldo2 {
+			regulator-min-microvolt = <1503000>;
+			regulator-max-microvolt = <1980000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l3a: ldo3 {
+			regulator-min-microvolt = <2700000>;
+			regulator-max-microvolt = <3300000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l4a: ldo4 {
+			regulator-min-microvolt = <352000>;
+			regulator-max-microvolt = <801000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l5a: ldo5 {
+			regulator-min-microvolt = <1503000>;
+			regulator-max-microvolt = <1980000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l6a: ldo6 {
+			regulator-min-microvolt = <1710000>;
+			regulator-max-microvolt = <3544000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l7a: ldo7 {
+			regulator-min-microvolt = <1620000>;
+			regulator-max-microvolt = <1980000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l8a: ldo8 {
+			regulator-min-microvolt = <2800000>;
+			regulator-max-microvolt = <2800000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l9a: ldo9 {
+			regulator-min-microvolt = <1650000>;
+			regulator-max-microvolt = <3401000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l11a: ldo11 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <2000000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l12a: ldo12 {
+			regulator-min-microvolt = <1620000>;
+			regulator-max-microvolt = <1980000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l13a: ldo13 {
+			regulator-min-microvolt = <570000>;
+			regulator-max-microvolt = <650000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l14a: ldo14 {
+			regulator-min-microvolt = <1700000>;
+			regulator-max-microvolt = <1900000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l15a: ldo15 {
+			regulator-min-microvolt = <1100000>;
+			regulator-max-microvolt = <1305000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l16a: ldo16 {
+			regulator-min-microvolt = <830000>;
+			regulator-max-microvolt = <921000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l18a: ldo18 {
+			regulator-min-microvolt = <788000>;
+			regulator-max-microvolt = <1049000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l19a: ldo19 {
+			regulator-min-microvolt = <1080000>;
+			regulator-max-microvolt = <1305000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l20a: ldo20 {
+			regulator-min-microvolt = <530000>;
+			regulator-max-microvolt = <801000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l21a: ldo21 {
+			regulator-min-microvolt = <751000>;
+			regulator-max-microvolt = <825000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l22a: ldo22 {
+			regulator-min-microvolt = <1080000>;
+			regulator-max-microvolt = <1305000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+	};
+
+	pm6150l-rpmh-regulators {
+		compatible = "qcom,pm6150l-rpmh-regulators";
+		qcom,pmic-id = "e";
+
+		vreg_s8e: smps8 {
+			regulator-min-microvolt = <313000>;
+			regulator-max-microvolt = <1395000>;
+		};
+
+		vreg_l1e: ldo1 {
+			regulator-min-microvolt = <1620000>;
+			regulator-max-microvolt = <1980000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l2e: ldo2 {
+			regulator-min-microvolt = <1170000>;
+			regulator-max-microvolt = <1305000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l3e: ldo3 {
+			regulator-min-microvolt = <1100000>;
+			regulator-max-microvolt = <1299000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l4e: ldo4 {
+			regulator-min-microvolt = <1620000>;
+			regulator-max-microvolt = <3300000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l5e: ldo5 {
+			regulator-min-microvolt = <1620000>;
+			regulator-max-microvolt = <3300000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l6e: ldo6 {
+			regulator-min-microvolt = <1700000>;
+			regulator-max-microvolt = <3544000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l7e: ldo7 {
+			regulator-min-microvolt = <2700000>;
+			regulator-max-microvolt = <3544000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l8e: ldo8 {
+			regulator-min-microvolt = <1620000>;
+			regulator-max-microvolt = <2000000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l9e: ldo9 {
+			regulator-min-microvolt = <2700000>;
+			regulator-max-microvolt = <3544000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l10e: ldo10 {
+			regulator-min-microvolt = <3000000>;
+			regulator-max-microvolt = <3401000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l11e: ldo11 {
+			regulator-min-microvolt = <3000000>;
+			regulator-max-microvolt = <3401000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_bob: bob {
+			regulator-min-microvolt = <1620000>;
+			regulator-max-microvolt = <5492000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_AUTO>;
+			regulator-allow-bypass;
+		};
+	};
+};
+
+&pm6350_gpios {
+	gpio_keys_pin: gpio-keys-pin {
+		pins = "gpio2";
+		function = PMIC_GPIO_FUNC_NORMAL;
+		bias-pull-up;
+		input-enable;
+		power-source = <0>;
+	};
+};
+
+&pm6350_resin {
+	status = "okay";
+	linux,code = <KEY_VOLUMEDOWN>;
+};
+
+&qupv3_id_1 {
+	status = "okay";
+};
+
+&tlmm {
+	gpio-reserved-ranges = <13 4>, <56 2>;
+};
+
+&uart2 {
+	status = "okay";
+};
+
+&usb_1 {
+	status = "okay";
+};
+
+&usb_1_dwc3 {
+	maximum-speed = "super-speed";
+	dr_mode = "peripheral";
+};
+
+&usb_1_hsphy {
+	status = "okay";
+
+	vdd-supply = <&vreg_l18a>;
+	vdda-pll-supply = <&vreg_l2a>;
+	vdda-phy-dpdm-supply = <&vreg_l3a>;
+};
+
+&usb_1_qmpphy {
+	status = "okay";
+
+	vdda-phy-supply = <&vreg_l22a>;
+	vdda-pll-supply = <&vreg_l16a>;
+};
diff --git a/arch/arm64/boot/dts/qcom/sm7225.dtsi b/arch/arm64/boot/dts/qcom/sm7225.dtsi
new file mode 100644
index 000000000000..7b2a002ca7ff
--- /dev/null
+++ b/arch/arm64/boot/dts/qcom/sm7225.dtsi
@@ -0,0 +1,16 @@
+// SPDX-License-Identifier: BSD-3-Clause
+/*
+ * Copyright (c) 2021, Luca Weiss <luca@z3ntu.xyz>
+ */
+
+#include "sm6350.dtsi"
+
+/* SM7225 uses Kryo 570 instead of Kryo 560 */
+&CPU0 { compatible = "qcom,kryo570"; };
+&CPU1 { compatible = "qcom,kryo570"; };
+&CPU2 { compatible = "qcom,kryo570"; };
+&CPU3 { compatible = "qcom,kryo570"; };
+&CPU4 { compatible = "qcom,kryo570"; };
+&CPU5 { compatible = "qcom,kryo570"; };
+&CPU6 { compatible = "qcom,kryo570"; };
+&CPU7 { compatible = "qcom,kryo570"; };
diff --git a/arch/arm64/boot/dts/qcom/sm8150-hdk.dts b/arch/arm64/boot/dts/qcom/sm8150-hdk.dts
index 335aa0753fc0..37ddca0f0223 100644
--- a/arch/arm64/boot/dts/qcom/sm8150-hdk.dts
+++ b/arch/arm64/boot/dts/qcom/sm8150-hdk.dts
@@ -419,9 +419,7 @@
 	status = "okay";
 
 	vdda-phy-supply = <&vdda_ufs_2ln_core_1>;
-	vdda-max-microamp = <90200>;
 	vdda-pll-supply = <&vreg_l3c_1p2>;
-	vdda-pll-max-microamp = <19000>;
 };
 
 &usb_1_hsphy {
diff --git a/arch/arm64/boot/dts/qcom/sm8150-microsoft-surface-duo.dts b/arch/arm64/boot/dts/qcom/sm8150-microsoft-surface-duo.dts
index 736da9af44e0..5901c28e6696 100644
--- a/arch/arm64/boot/dts/qcom/sm8150-microsoft-surface-duo.dts
+++ b/arch/arm64/boot/dts/qcom/sm8150-microsoft-surface-duo.dts
@@ -15,6 +15,7 @@
 / {
 	model = "Microsoft Surface Duo";
 	compatible = "microsoft,surface-duo", "qcom,sm8150";
+	chassis-type = "handset";
 
 	aliases {
 		serial0 = &uart2;
@@ -507,9 +508,7 @@
 	status = "okay";
 
 	vdda-phy-supply = <&vdda_ufs_2ln_core_1>;
-	vdda-max-microamp = <90200>;
 	vdda-pll-supply = <&vreg_l3c_1p2>;
-	vdda-pll-max-microamp = <19000>;
 };
 
 &usb_1_hsphy {
diff --git a/arch/arm64/boot/dts/qcom/sm8150-mtp.dts b/arch/arm64/boot/dts/qcom/sm8150-mtp.dts
index b484371a6044..46b5cf9a1192 100644
--- a/arch/arm64/boot/dts/qcom/sm8150-mtp.dts
+++ b/arch/arm64/boot/dts/qcom/sm8150-mtp.dts
@@ -416,9 +416,7 @@
 	status = "okay";
 
 	vdda-phy-supply = <&vdda_ufs_2ln_core_1>;
-	vdda-max-microamp = <90200>;
 	vdda-pll-supply = <&vreg_l3c_1p2>;
-	vdda-pll-max-microamp = <19000>;
 };
 
 &usb_1_hsphy {
diff --git a/arch/arm64/boot/dts/qcom/sm8150-sony-xperia-kumano-bahamut.dts b/arch/arm64/boot/dts/qcom/sm8150-sony-xperia-kumano-bahamut.dts
index 3b55fdda767a..b2780403255e 100644
--- a/arch/arm64/boot/dts/qcom/sm8150-sony-xperia-kumano-bahamut.dts
+++ b/arch/arm64/boot/dts/qcom/sm8150-sony-xperia-kumano-bahamut.dts
@@ -10,6 +10,7 @@
 / {
 	model = "Sony Xperia 5";
 	compatible = "sony,bahamut-generic", "qcom,sm8150";
+	chassis-type = "handset";
 };
 
 &framebuffer {
diff --git a/arch/arm64/boot/dts/qcom/sm8150-sony-xperia-kumano-griffin.dts b/arch/arm64/boot/dts/qcom/sm8150-sony-xperia-kumano-griffin.dts
index 6f490ec284bd..0d6deceedf46 100644
--- a/arch/arm64/boot/dts/qcom/sm8150-sony-xperia-kumano-griffin.dts
+++ b/arch/arm64/boot/dts/qcom/sm8150-sony-xperia-kumano-griffin.dts
@@ -10,4 +10,5 @@
 / {
 	model = "Sony Xperia 1";
 	compatible = "sony,griffin-generic", "qcom,sm8150";
+	chassis-type = "handset";
 };
diff --git a/arch/arm64/boot/dts/qcom/sm8150.dtsi b/arch/arm64/boot/dts/qcom/sm8150.dtsi
index ef0232c2cf45..81b4ff2cc4cd 100644
--- a/arch/arm64/boot/dts/qcom/sm8150.dtsi
+++ b/arch/arm64/boot/dts/qcom/sm8150.dtsi
@@ -6,7 +6,6 @@
 
 #include <dt-bindings/dma/qcom-gpi.h>
 #include <dt-bindings/interrupt-controller/arm-gic.h>
-#include <dt-bindings/power/qcom-aoss-qmp.h>
 #include <dt-bindings/power/qcom-rpmpd.h>
 #include <dt-bindings/soc/qcom,rpmh-rsc.h>
 #include <dt-bindings/clock/qcom,rpmh.h>
@@ -1692,7 +1691,7 @@
 			reset-names = "ufsphy";
 			status = "disabled";
 
-			ufs_mem_phy_lanes: lanes@1d87400 {
+			ufs_mem_phy_lanes: phy@1d87400 {
 				reg = <0 0x01d87400 0 0x108>,
 				      <0 0x01d87600 0 0x1e0>,
 				      <0 0x01d87c00 0 0x1dc>,
@@ -1729,13 +1728,14 @@
 			clocks = <&rpmhcc RPMH_CXO_CLK>;
 			clock-names = "xo";
 
-			power-domains = <&aoss_qmp AOSS_QMP_LS_SLPI>,
-					<&rpmhpd 3>,
+			power-domains = <&rpmhpd 3>,
 					<&rpmhpd 2>;
-			power-domain-names = "load_state", "lcx", "lmx";
+			power-domain-names = "lcx", "lmx";
 
 			memory-region = <&slpi_mem>;
 
+			qcom,qmp = <&aoss_qmp>;
+
 			qcom,smem-states = <&slpi_smp2p_out 0>;
 			qcom,smem-state-names = "stop";
 
@@ -1746,6 +1746,33 @@
 				label = "dsps";
 				qcom,remote-pid = <3>;
 				mboxes = <&apss_shared 24>;
+
+				fastrpc {
+					compatible = "qcom,fastrpc";
+					qcom,glink-channels = "fastrpcglink-apps-dsp";
+					label = "sdsp";
+					#address-cells = <1>;
+					#size-cells = <0>;
+
+					compute-cb@1 {
+						compatible = "qcom,fastrpc-compute-cb";
+						reg = <1>;
+						iommus = <&apps_smmu 0x05a1 0x0>;
+					};
+
+					compute-cb@2 {
+						compatible = "qcom,fastrpc-compute-cb";
+						reg = <2>;
+						iommus = <&apps_smmu 0x05a2 0x0>;
+					};
+
+					compute-cb@3 {
+						compatible = "qcom,fastrpc-compute-cb";
+						reg = <3>;
+						iommus = <&apps_smmu 0x05a3 0x0>;
+						/* note: shared-cb = <4> in downstream */
+					};
+				};
 			};
 		};
 
@@ -2319,13 +2346,14 @@
 			clocks = <&rpmhcc RPMH_CXO_CLK>;
 			clock-names = "xo";
 
-			power-domains = <&aoss_qmp AOSS_QMP_LS_MODEM>,
-					<&rpmhpd 7>,
+			power-domains = <&rpmhpd 7>,
 					<&rpmhpd 0>;
-			power-domain-names = "load_state", "cx", "mss";
+			power-domain-names = "cx", "mss";
 
 			memory-region = <&mpss_mem>;
 
+			qcom,qmp = <&aoss_qmp>;
+
 			qcom,smem-states = <&modem_smp2p_out 0>;
 			qcom,smem-state-names = "stop";
 
@@ -2945,12 +2973,12 @@
 			clocks = <&rpmhcc RPMH_CXO_CLK>;
 			clock-names = "xo";
 
-			power-domains = <&aoss_qmp AOSS_QMP_LS_CDSP>,
-					<&rpmhpd 7>;
-			power-domain-names = "load_state", "cx";
+			power-domains = <&rpmhpd 7>;
 
 			memory-region = <&cdsp_mem>;
 
+			qcom,qmp = <&aoss_qmp>;
+
 			qcom,smem-states = <&cdsp_smp2p_out 0>;
 			qcom,smem-state-names = "stop";
 
@@ -2961,6 +2989,72 @@
 				label = "cdsp";
 				qcom,remote-pid = <5>;
 				mboxes = <&apss_shared 4>;
+
+				fastrpc {
+					compatible = "qcom,fastrpc";
+					qcom,glink-channels = "fastrpcglink-apps-dsp";
+					label = "cdsp";
+					#address-cells = <1>;
+					#size-cells = <0>;
+
+					compute-cb@1 {
+						compatible = "qcom,fastrpc-compute-cb";
+						reg = <1>;
+						iommus = <&apps_smmu 0x1401 0x2040>,
+							 <&apps_smmu 0x1421 0x0>,
+							 <&apps_smmu 0x2001 0x420>,
+							 <&apps_smmu 0x2041 0x0>;
+					};
+
+					compute-cb@2 {
+						compatible = "qcom,fastrpc-compute-cb";
+						reg = <2>;
+						iommus = <&apps_smmu 0x2 0x3440>,
+							 <&apps_smmu 0x22 0x3400>;
+					};
+
+					compute-cb@3 {
+						compatible = "qcom,fastrpc-compute-cb";
+						reg = <3>;
+						iommus = <&apps_smmu 0x3 0x3440>,
+							 <&apps_smmu 0x1423 0x0>,
+							 <&apps_smmu 0x2023 0x0>;
+					};
+
+					compute-cb@4 {
+						compatible = "qcom,fastrpc-compute-cb";
+						reg = <4>;
+						iommus = <&apps_smmu 0x4 0x3440>,
+							 <&apps_smmu 0x24 0x3400>;
+					};
+
+					compute-cb@5 {
+						compatible = "qcom,fastrpc-compute-cb";
+						reg = <5>;
+						iommus = <&apps_smmu 0x5 0x3440>,
+							 <&apps_smmu 0x25 0x3400>;
+					};
+
+					compute-cb@6 {
+						compatible = "qcom,fastrpc-compute-cb";
+						reg = <6>;
+						iommus = <&apps_smmu 0x6 0x3460>;
+					};
+
+					compute-cb@7 {
+						compatible = "qcom,fastrpc-compute-cb";
+						reg = <7>;
+						iommus = <&apps_smmu 0x7 0x3460>;
+					};
+
+					compute-cb@8 {
+						compatible = "qcom,fastrpc-compute-cb";
+						reg = <8>;
+						iommus = <&apps_smmu 0x8 0x3460>;
+					};
+
+					/* note: secure cb9 in downstream */
+				};
 			};
 		};
 
@@ -2994,7 +3088,6 @@
 			compatible = "qcom,sm8150-qmp-usb3-phy";
 			reg = <0 0x088e9000 0 0x18c>,
 			      <0 0x088e8000 0 0x10>;
-			reg-names = "reg-base", "dp_com";
 			status = "disabled";
 			#address-cells = <2>;
 			#size-cells = <2>;
@@ -3010,7 +3103,7 @@
 				 <&gcc GCC_USB3_PHY_PRIM_BCR>;
 			reset-names = "phy", "common";
 
-			usb_1_ssphy: lanes@88e9200 {
+			usb_1_ssphy: phy@88e9200 {
 				reg = <0 0x088e9200 0 0x200>,
 				      <0 0x088e9400 0 0x200>,
 				      <0 0x088e9c00 0 0x218>,
@@ -3043,7 +3136,7 @@
 				 <&gcc GCC_USB3_PHY_SEC_BCR>;
 			reset-names = "phy", "common";
 
-			usb_2_ssphy: lane@88eb200 {
+			usb_2_ssphy: phy@88eb200 {
 				reg = <0 0x088eb200 0 0x200>,
 				      <0 0x088eb400 0 0x200>,
 				      <0 0x088eb800 0 0x800>,
@@ -3169,12 +3262,16 @@
 
 		aoss_qmp: power-controller@c300000 {
 			compatible = "qcom,sm8150-aoss-qmp";
-			reg = <0x0 0x0c300000 0x0 0x100000>;
+			reg = <0x0 0x0c300000 0x0 0x400>;
 			interrupts = <GIC_SPI 389 IRQ_TYPE_EDGE_RISING>;
 			mboxes = <&apss_shared 0>;
 
 			#clock-cells = <0>;
-			#power-domain-cells = <1>;
+		};
+
+		sram@c3f0000 {
+			compatible = "qcom,rpmh-stats";
+			reg = <0 0x0c3f0000 0 0x400>;
 		};
 
 		tsens0: thermal-sensor@c263000 {
@@ -3321,12 +3418,12 @@
 			clocks = <&rpmhcc RPMH_CXO_CLK>;
 			clock-names = "xo";
 
-			power-domains = <&aoss_qmp AOSS_QMP_LS_LPASS>,
-					<&rpmhpd 7>;
-			power-domain-names = "load_state", "cx";
+			power-domains = <&rpmhpd 7>;
 
 			memory-region = <&adsp_mem>;
 
+			qcom,qmp = <&aoss_qmp>;
+
 			qcom,smem-states = <&adsp_smp2p_out 0>;
 			qcom,smem-state-names = "stop";
 
@@ -3337,6 +3434,32 @@
 				label = "lpass";
 				qcom,remote-pid = <2>;
 				mboxes = <&apss_shared 8>;
+
+				fastrpc {
+					compatible = "qcom,fastrpc";
+					qcom,glink-channels = "fastrpcglink-apps-dsp";
+					label = "adsp";
+					#address-cells = <1>;
+					#size-cells = <0>;
+
+					compute-cb@3 {
+						compatible = "qcom,fastrpc-compute-cb";
+						reg = <3>;
+						iommus = <&apps_smmu 0x1b23 0x0>;
+					};
+
+					compute-cb@4 {
+						compatible = "qcom,fastrpc-compute-cb";
+						reg = <4>;
+						iommus = <&apps_smmu 0x1b24 0x0>;
+					};
+
+					compute-cb@5 {
+						compatible = "qcom,fastrpc-compute-cb";
+						reg = <5>;
+						iommus = <&apps_smmu 0x1b25 0x0>;
+					};
+				};
 			};
 		};
 
diff --git a/arch/arm64/boot/dts/qcom/sm8250-hdk.dts b/arch/arm64/boot/dts/qcom/sm8250-hdk.dts
index 47742816ac2f..3b082472062b 100644
--- a/arch/arm64/boot/dts/qcom/sm8250-hdk.dts
+++ b/arch/arm64/boot/dts/qcom/sm8250-hdk.dts
@@ -409,9 +409,7 @@
 	status = "okay";
 
 	vdda-phy-supply = <&vreg_l5a_0p88>;
-	vdda-max-microamp = <89900>;
 	vdda-pll-supply = <&vreg_l9a_1p2>;
-	vdda-pll-max-microamp = <18800>;
 };
 
 &usb_1_hsphy {
diff --git a/arch/arm64/boot/dts/qcom/sm8250-mtp.dts b/arch/arm64/boot/dts/qcom/sm8250-mtp.dts
index 062b944be91d..5ffbcdd387ba 100644
--- a/arch/arm64/boot/dts/qcom/sm8250-mtp.dts
+++ b/arch/arm64/boot/dts/qcom/sm8250-mtp.dts
@@ -647,9 +647,7 @@
 	status = "okay";
 
 	vdda-phy-supply = <&vreg_l5a_0p875>;
-	vdda-max-microamp = <90200>;
 	vdda-pll-supply = <&vreg_l9a_1p2>;
-	vdda-pll-max-microamp = <19000>;
 };
 
 &usb_1 {
diff --git a/arch/arm64/boot/dts/qcom/sm8250-sony-xperia-edo-pdx203.dts b/arch/arm64/boot/dts/qcom/sm8250-sony-xperia-edo-pdx203.dts
index 79afeb07f4a2..356a81698731 100644
--- a/arch/arm64/boot/dts/qcom/sm8250-sony-xperia-edo-pdx203.dts
+++ b/arch/arm64/boot/dts/qcom/sm8250-sony-xperia-edo-pdx203.dts
@@ -10,6 +10,7 @@
 / {
 	model = "Sony Xperia 1 II";
 	compatible = "sony,pdx203-generic", "qcom,sm8250";
+	chassis-type = "handset";
 };
 
 /delete-node/ &vreg_l7f_1p8;
diff --git a/arch/arm64/boot/dts/qcom/sm8250-sony-xperia-edo-pdx206.dts b/arch/arm64/boot/dts/qcom/sm8250-sony-xperia-edo-pdx206.dts
index 16c96e838534..5ecf7dafb2ec 100644
--- a/arch/arm64/boot/dts/qcom/sm8250-sony-xperia-edo-pdx206.dts
+++ b/arch/arm64/boot/dts/qcom/sm8250-sony-xperia-edo-pdx206.dts
@@ -10,6 +10,7 @@
 / {
 	model = "Sony Xperia 5 II";
 	compatible = "sony,pdx206-generic", "qcom,sm8250";
+	chassis-type = "handset";
 };
 
 &framebuffer {
diff --git a/arch/arm64/boot/dts/qcom/sm8250.dtsi b/arch/arm64/boot/dts/qcom/sm8250.dtsi
index d12e4cbfc852..6f6129b39c9c 100644
--- a/arch/arm64/boot/dts/qcom/sm8250.dtsi
+++ b/arch/arm64/boot/dts/qcom/sm8250.dtsi
@@ -13,7 +13,6 @@
 #include <dt-bindings/interconnect/qcom,osm-l3.h>
 #include <dt-bindings/interconnect/qcom,sm8250.h>
 #include <dt-bindings/mailbox/qcom-ipcc.h>
-#include <dt-bindings/power/qcom-aoss-qmp.h>
 #include <dt-bindings/power/qcom-rpmpd.h>
 #include <dt-bindings/soc/qcom,apr.h>
 #include <dt-bindings/soc/qcom,rpmh-rsc.h>
@@ -273,13 +272,6 @@
 		reg = <0x0 0x80000000 0x0 0x0>;
 	};
 
-	mmcx_reg: mmcx-reg {
-		compatible = "regulator-fixed-domain";
-		power-domains = <&rpmhpd SM8250_MMCX>;
-		required-opps = <&rpmhpd_opp_low_svs>;
-		regulator-name = "MMCX";
-	};
-
 	pmu {
 		compatible = "arm,armv8-pmuv3";
 		interrupts = <GIC_PPI 7 IRQ_TYPE_LEVEL_LOW>;
@@ -1463,7 +1455,7 @@
 
 			status = "disabled";
 
-			pcie0_lane: lanes@1c06200 {
+			pcie0_lane: phy@1c06200 {
 				reg = <0 0x1c06200 0 0x170>, /* tx */
 				      <0 0x1c06400 0 0x200>, /* rx */
 				      <0 0x1c06800 0 0x1f0>, /* pcs */
@@ -1567,7 +1559,7 @@
 
 			status = "disabled";
 
-			pcie1_lane: lanes@1c0e200 {
+			pcie1_lane: phy@1c0e200 {
 				reg = <0 0x1c0e200 0 0x170>, /* tx0 */
 				      <0 0x1c0e400 0 0x200>, /* rx0 */
 				      <0 0x1c0ea00 0 0x1f0>, /* pcs */
@@ -1673,7 +1665,7 @@
 
 			status = "disabled";
 
-			pcie2_lane: lanes@1c16200 {
+			pcie2_lane: phy@1c16200 {
 				reg = <0 0x1c16200 0 0x170>, /* tx0 */
 				      <0 0x1c16400 0 0x200>, /* rx0 */
 				      <0 0x1c16a00 0 0x1f0>, /* pcs */
@@ -1750,7 +1742,7 @@
 			reset-names = "ufsphy";
 			status = "disabled";
 
-			ufs_mem_phy_lanes: lanes@1d87400 {
+			ufs_mem_phy_lanes: phy@1d87400 {
 				reg = <0 0x01d87400 0 0x108>,
 				      <0 0x01d87600 0 0x1e0>,
 				      <0 0x01d87c00 0 0x1dc>,
@@ -2088,13 +2080,14 @@
 			clocks = <&rpmhcc RPMH_CXO_CLK>;
 			clock-names = "xo";
 
-			power-domains = <&aoss_qmp AOSS_QMP_LS_SLPI>,
-					<&rpmhpd SM8250_LCX>,
+			power-domains = <&rpmhpd SM8250_LCX>,
 					<&rpmhpd SM8250_LMX>;
-			power-domain-names = "load_state", "lcx", "lmx";
+			power-domain-names = "lcx", "lmx";
 
 			memory-region = <&slpi_mem>;
 
+			qcom,qmp = <&aoss_qmp>;
+
 			qcom,smem-states = <&smp2p_slpi_out 0>;
 			qcom,smem-state-names = "stop";
 
@@ -2154,12 +2147,12 @@
 			clocks = <&rpmhcc RPMH_CXO_CLK>;
 			clock-names = "xo";
 
-			power-domains = <&aoss_qmp AOSS_QMP_LS_CDSP>,
-					<&rpmhpd SM8250_CX>;
-			power-domain-names = "load_state", "cx";
+			power-domains = <&rpmhpd SM8250_CX>;
 
 			memory-region = <&cdsp_mem>;
 
+			qcom,qmp = <&aoss_qmp>;
+
 			qcom,smem-states = <&smp2p_cdsp_out 0>;
 			qcom,smem-state-names = "stop";
 
@@ -2330,7 +2323,7 @@
 				 <&gcc GCC_USB3_PHY_SEC_BCR>;
 			reset-names = "phy", "common";
 
-			usb_2_ssphy: lanes@88eb200 {
+			usb_2_ssphy: phy@88eb200 {
 				reg = <0 0x088eb200 0 0x200>,
 				      <0 0x088eb400 0 0x200>,
 				      <0 0x088eb800 0 0x800>;
@@ -2571,7 +2564,8 @@
 			clocks = <&gcc GCC_VIDEO_AHB_CLK>,
 				 <&rpmhcc RPMH_CXO_CLK>,
 				 <&rpmhcc RPMH_CXO_CLK_A>;
-			mmcx-supply = <&mmcx_reg>;
+			power-domains = <&rpmhpd SM8250_MMCX>;
+			required-opps = <&rpmhpd_opp_low_svs>;
 			clock-names = "iface", "bi_tcxo", "bi_tcxo_ao";
 			#clock-cells = <1>;
 			#reset-cells = <1>;
@@ -2846,7 +2840,8 @@
 		dispcc: clock-controller@af00000 {
 			compatible = "qcom,sm8250-dispcc";
 			reg = <0 0x0af00000 0 0x10000>;
-			mmcx-supply = <&mmcx_reg>;
+			power-domains = <&rpmhpd SM8250_MMCX>;
+			required-opps = <&rpmhpd_opp_low_svs>;
 			clocks = <&rpmhcc RPMH_CXO_CLK>,
 				 <&dsi0_phy 0>,
 				 <&dsi0_phy 1>,
@@ -2900,7 +2895,7 @@
 
 		aoss_qmp: power-controller@c300000 {
 			compatible = "qcom,sm8250-aoss-qmp";
-			reg = <0 0x0c300000 0 0x100000>;
+			reg = <0 0x0c300000 0 0x400>;
 			interrupts-extended = <&ipcc IPCC_CLIENT_AOP
 						     IPCC_MPROC_SIGNAL_GLINK_QMP
 						     IRQ_TYPE_EDGE_RISING>;
@@ -2908,7 +2903,11 @@
 					IPCC_MPROC_SIGNAL_GLINK_QMP>;
 
 			#clock-cells = <0>;
-			#power-domain-cells = <1>;
+		};
+
+		sram@c3f0000 {
+			compatible = "qcom,rpmh-stats";
+			reg = <0 0x0c3f0000 0 0x400>;
 		};
 
 		spmi_bus: spmi@c440000 {
@@ -3825,13 +3824,14 @@
 			clocks = <&rpmhcc RPMH_CXO_CLK>;
 			clock-names = "xo";
 
-			power-domains = <&aoss_qmp AOSS_QMP_LS_LPASS>,
-					<&rpmhpd SM8250_LCX>,
+			power-domains = <&rpmhpd SM8250_LCX>,
 					<&rpmhpd SM8250_LMX>;
-			power-domain-names = "load_state", "lcx", "lmx";
+			power-domain-names = "lcx", "lmx";
 
 			memory-region = <&adsp_mem>;
 
+			qcom,qmp = <&aoss_qmp>;
+
 			qcom,smem-states = <&smp2p_adsp_out 0>;
 			qcom,smem-state-names = "stop";
 
diff --git a/arch/arm64/boot/dts/qcom/sm8350-hdk.dts b/arch/arm64/boot/dts/qcom/sm8350-hdk.dts
index 56093e260ddf..be062377c936 100644
--- a/arch/arm64/boot/dts/qcom/sm8350-hdk.dts
+++ b/arch/arm64/boot/dts/qcom/sm8350-hdk.dts
@@ -251,9 +251,7 @@
 	status = "okay";
 
 	vdda-phy-supply = <&vreg_l5b_0p88>;
-	vdda-max-microamp = <91600>;
 	vdda-pll-supply = <&vreg_l6b_1p2>;
-	vdda-pll-max-microamp = <19000>;
 };
 
 &usb_1 {
diff --git a/arch/arm64/boot/dts/qcom/sm8350-mtp.dts b/arch/arm64/boot/dts/qcom/sm8350-mtp.dts
index bd95009c1875..06eedbe52c42 100644
--- a/arch/arm64/boot/dts/qcom/sm8350-mtp.dts
+++ b/arch/arm64/boot/dts/qcom/sm8350-mtp.dts
@@ -286,6 +286,10 @@
 	firmware-name = "qcom/sm8350/modem.mbn";
 };
 
+&pmk8350_rtc {
+	status = "okay";
+};
+
 &qupv3_id_0 {
 	status = "okay";
 };
@@ -318,9 +322,7 @@
 	status = "okay";
 
 	vdda-phy-supply = <&vreg_l5b_0p88>;
-	vdda-max-microamp = <91600>;
 	vdda-pll-supply = <&vreg_l6b_1p2>;
-	vdda-pll-max-microamp = <19000>;
 };
 
 &usb_1 {
diff --git a/arch/arm64/boot/dts/qcom/sm8350.dtsi b/arch/arm64/boot/dts/qcom/sm8350.dtsi
index e91cd8a5e535..d134280e2939 100644
--- a/arch/arm64/boot/dts/qcom/sm8350.dtsi
+++ b/arch/arm64/boot/dts/qcom/sm8350.dtsi
@@ -8,7 +8,6 @@
 #include <dt-bindings/clock/qcom,rpmh.h>
 #include <dt-bindings/interconnect/qcom,sm8350.h>
 #include <dt-bindings/mailbox/qcom-ipcc.h>
-#include <dt-bindings/power/qcom-aoss-qmp.h>
 #include <dt-bindings/power/qcom-rpmpd.h>
 #include <dt-bindings/soc/qcom,rpmh-rsc.h>
 #include <dt-bindings/thermal/thermal.h>
@@ -48,6 +47,8 @@
 			enable-method = "psci";
 			next-level-cache = <&L2_0>;
 			qcom,freq-domain = <&cpufreq_hw 0>;
+			power-domains = <&CPU_PD0>;
+			power-domain-names = "psci";
 			#cooling-cells = <2>;
 			L2_0: l2-cache {
 			      compatible = "cache";
@@ -65,6 +66,8 @@
 			enable-method = "psci";
 			next-level-cache = <&L2_100>;
 			qcom,freq-domain = <&cpufreq_hw 0>;
+			power-domains = <&CPU_PD1>;
+			power-domain-names = "psci";
 			#cooling-cells = <2>;
 			L2_100: l2-cache {
 			      compatible = "cache";
@@ -79,6 +82,8 @@
 			enable-method = "psci";
 			next-level-cache = <&L2_200>;
 			qcom,freq-domain = <&cpufreq_hw 0>;
+			power-domains = <&CPU_PD2>;
+			power-domain-names = "psci";
 			#cooling-cells = <2>;
 			L2_200: l2-cache {
 			      compatible = "cache";
@@ -93,6 +98,8 @@
 			enable-method = "psci";
 			next-level-cache = <&L2_300>;
 			qcom,freq-domain = <&cpufreq_hw 0>;
+			power-domains = <&CPU_PD3>;
+			power-domain-names = "psci";
 			#cooling-cells = <2>;
 			L2_300: l2-cache {
 			      compatible = "cache";
@@ -107,6 +114,8 @@
 			enable-method = "psci";
 			next-level-cache = <&L2_400>;
 			qcom,freq-domain = <&cpufreq_hw 1>;
+			power-domains = <&CPU_PD4>;
+			power-domain-names = "psci";
 			#cooling-cells = <2>;
 			L2_400: l2-cache {
 			      compatible = "cache";
@@ -121,6 +130,8 @@
 			enable-method = "psci";
 			next-level-cache = <&L2_500>;
 			qcom,freq-domain = <&cpufreq_hw 1>;
+			power-domains = <&CPU_PD5>;
+			power-domain-names = "psci";
 			#cooling-cells = <2>;
 			L2_500: l2-cache {
 			      compatible = "cache";
@@ -136,6 +147,8 @@
 			enable-method = "psci";
 			next-level-cache = <&L2_600>;
 			qcom,freq-domain = <&cpufreq_hw 1>;
+			power-domains = <&CPU_PD6>;
+			power-domain-names = "psci";
 			#cooling-cells = <2>;
 			L2_600: l2-cache {
 			      compatible = "cache";
@@ -150,12 +163,86 @@
 			enable-method = "psci";
 			next-level-cache = <&L2_700>;
 			qcom,freq-domain = <&cpufreq_hw 2>;
+			power-domains = <&CPU_PD7>;
+			power-domain-names = "psci";
 			#cooling-cells = <2>;
 			L2_700: l2-cache {
 			      compatible = "cache";
 			      next-level-cache = <&L3_0>;
 			};
 		};
+
+		cpu-map {
+			cluster0 {
+				core0 {
+					cpu = <&CPU0>;
+				};
+
+				core1 {
+					cpu = <&CPU1>;
+				};
+
+				core2 {
+					cpu = <&CPU2>;
+				};
+
+				core3 {
+					cpu = <&CPU3>;
+				};
+
+				core4 {
+					cpu = <&CPU4>;
+				};
+
+				core5 {
+					cpu = <&CPU5>;
+				};
+
+				core6 {
+					cpu = <&CPU6>;
+				};
+
+				core7 {
+					cpu = <&CPU7>;
+				};
+			};
+		};
+
+		idle-states {
+			entry-method = "psci";
+
+			LITTLE_CPU_SLEEP_0: cpu-sleep-0-0 {
+				compatible = "arm,idle-state";
+				idle-state-name = "silver-rail-power-collapse";
+				arm,psci-suspend-param = <0x40000004>;
+				entry-latency-us = <355>;
+				exit-latency-us = <909>;
+				min-residency-us = <3934>;
+				local-timer-stop;
+			};
+
+			BIG_CPU_SLEEP_0: cpu-sleep-1-0 {
+				compatible = "arm,idle-state";
+				idle-state-name = "gold-rail-power-collapse";
+				arm,psci-suspend-param = <0x40000004>;
+				entry-latency-us = <241>;
+				exit-latency-us = <1461>;
+				min-residency-us = <4488>;
+				local-timer-stop;
+			};
+		};
+
+		domain-idle-states {
+			CLUSTER_SLEEP_0: cluster-sleep-0 {
+				compatible = "domain-idle-state";
+				idle-state-name = "cluster-power-collapse";
+				arm,psci-suspend-param = <0x4100c344>;
+				entry-latency-us = <3263>;
+				exit-latency-us = <6562>;
+				min-residency-us = <9987>;
+				local-timer-stop;
+			};
+		};
 	};
 
 	firmware {
@@ -179,6 +266,59 @@
 	psci {
 		compatible = "arm,psci-1.0";
 		method = "smc";
+
+		CPU_PD0: cpu0 {
+			#power-domain-cells = <0>;
+			power-domains = <&CLUSTER_PD>;
+			domain-idle-states = <&LITTLE_CPU_SLEEP_0>;
+		};
+
+		CPU_PD1: cpu1 {
+			#power-domain-cells = <0>;
+			power-domains = <&CLUSTER_PD>;
+			domain-idle-states = <&LITTLE_CPU_SLEEP_0>;
+		};
+
+		CPU_PD2: cpu2 {
+			#power-domain-cells = <0>;
+			power-domains = <&CLUSTER_PD>;
+			domain-idle-states = <&LITTLE_CPU_SLEEP_0>;
+		};
+
+		CPU_PD3: cpu3 {
+			#power-domain-cells = <0>;
+			power-domains = <&CLUSTER_PD>;
+			domain-idle-states = <&LITTLE_CPU_SLEEP_0>;
+		};
+
+		CPU_PD4: cpu4 {
+			#power-domain-cells = <0>;
+			power-domains = <&CLUSTER_PD>;
+			domain-idle-states = <&BIG_CPU_SLEEP_0>;
+		};
+
+		CPU_PD5: cpu5 {
+			#power-domain-cells = <0>;
+			power-domains = <&CLUSTER_PD>;
+			domain-idle-states = <&BIG_CPU_SLEEP_0>;
+		};
+
+		CPU_PD6: cpu6 {
+			#power-domain-cells = <0>;
+			power-domains = <&CLUSTER_PD>;
+			domain-idle-states = <&BIG_CPU_SLEEP_0>;
+		};
+
+		CPU_PD7: cpu7 {
+			#power-domain-cells = <0>;
+			power-domains = <&CLUSTER_PD>;
+			domain-idle-states = <&BIG_CPU_SLEEP_0>;
+		};
+
+		CLUSTER_PD: cpu-cluster0 {
+			#power-domain-cells = <0>;
+			domain-idle-states = <&CLUSTER_SLEEP_0>;
+		};
 	};
 
 	reserved_memory: reserved-memory {
@@ -726,15 +866,16 @@
 			clocks = <&rpmhcc RPMH_CXO_CLK>;
 			clock-names = "xo";
 
-			power-domains = <&aoss_qmp AOSS_QMP_LS_MODEM>,
-					<&rpmhpd 0>,
+			power-domains = <&rpmhpd 0>,
 					<&rpmhpd 12>;
-			power-domain-names = "load_state", "cx", "mss";
+			power-domain-names = "cx", "mss";
 
 			interconnects = <&mc_virt MASTER_LLCC &mc_virt SLAVE_EBI1>;
 
 			memory-region = <&pil_modem_mem>;
 
+			qcom,qmp = <&aoss_qmp>;
+
 			qcom,smem-states = <&smp2p_modem_out 0>;
 			qcom,smem-state-names = "stop";
 
@@ -788,13 +929,17 @@
 
 		aoss_qmp: power-controller@c300000 {
 			compatible = "qcom,sm8350-aoss-qmp";
-			reg = <0 0x0c300000 0 0x100000>;
+			reg = <0 0x0c300000 0 0x400>;
 			interrupts-extended = <&ipcc IPCC_CLIENT_AOP IPCC_MPROC_SIGNAL_GLINK_QMP
 						     IRQ_TYPE_EDGE_RISING>;
 			mboxes = <&ipcc IPCC_CLIENT_AOP IPCC_MPROC_SIGNAL_GLINK_QMP>;
 
 			#clock-cells = <0>;
-			#power-domain-cells = <1>;
+		};
+
+		sram@c3f0000 {
+			compatible = "qcom,rpmh-stats";
+			reg = <0 0x0c3f0000 0 0x400>;
 		};
 
 		spmi_bus: spmi@c440000 {
@@ -1070,7 +1215,6 @@
 			reg = <0 0x01d87000 0 0xe10>;
 			#address-cells = <2>;
 			#size-cells = <2>;
-			#clock-cells = <1>;
 			ranges;
 			clock-names = "ref",
 				      "ref_aux";
@@ -1081,7 +1225,7 @@
 			reset-names = "ufsphy";
 			status = "disabled";
 
-			ufs_mem_phy_lanes: lanes@1d87400 {
+			ufs_mem_phy_lanes: phy@1d87400 {
 				reg = <0 0x01d87400 0 0x108>,
 				      <0 0x01d87600 0 0x1e0>,
 				      <0 0x01d87c00 0 0x1dc>,
@@ -1107,13 +1251,14 @@
 			clocks = <&rpmhcc RPMH_CXO_CLK>;
 			clock-names = "xo";
 
-			power-domains = <&aoss_qmp AOSS_QMP_LS_SLPI>,
-					<&rpmhpd 4>,
+			power-domains = <&rpmhpd 4>,
 					<&rpmhpd 5>;
-			power-domain-names = "load_state", "lcx", "lmx";
+			power-domain-names = "lcx", "lmx";
 
 			memory-region = <&pil_slpi_mem>;
 
+			qcom,qmp = <&aoss_qmp>;
+
 			qcom,smem-states = <&smp2p_slpi_out 0>;
 			qcom,smem-state-names = "stop";
 
@@ -1129,6 +1274,32 @@
 				label = "slpi";
 				qcom,remote-pid = <3>;
 
+				fastrpc {
+					compatible = "qcom,fastrpc";
+					qcom,glink-channels = "fastrpcglink-apps-dsp";
+					label = "sdsp";
+					#address-cells = <1>;
+					#size-cells = <0>;
+
+					compute-cb@1 {
+						compatible = "qcom,fastrpc-compute-cb";
+						reg = <1>;
+						iommus = <&apps_smmu 0x0541 0x0>;
+					};
+
+					compute-cb@2 {
+						compatible = "qcom,fastrpc-compute-cb";
+						reg = <2>;
+						iommus = <&apps_smmu 0x0542 0x0>;
+					};
+
+					compute-cb@3 {
+						compatible = "qcom,fastrpc-compute-cb";
+						reg = <3>;
+						iommus = <&apps_smmu 0x0543 0x0>;
+						/* note: shared-cb = <4> in downstream */
+					};
+				};
 			};
 		};
 
@@ -1147,15 +1318,16 @@
 			clocks = <&rpmhcc RPMH_CXO_CLK>;
 			clock-names = "xo";
 
-			power-domains = <&aoss_qmp AOSS_QMP_LS_CDSP>,
-					<&rpmhpd 0>,
+			power-domains = <&rpmhpd 0>,
 					<&rpmhpd 10>;
-			power-domain-names = "load_state", "cx", "mxc";
+			power-domain-names = "cx", "mxc";
 
 			interconnects = <&compute_noc MASTER_CDSP_PROC &mc_virt SLAVE_EBI1>;
 
 			memory-region = <&pil_cdsp_mem>;
 
+			qcom,qmp = <&aoss_qmp>;
+
 			qcom,smem-states = <&smp2p_cdsp_out 0>;
 			qcom,smem-state-names = "stop";
 
@@ -1170,6 +1342,72 @@
 
 				label = "cdsp";
 				qcom,remote-pid = <5>;
+
+				fastrpc {
+					compatible = "qcom,fastrpc";
+					qcom,glink-channels = "fastrpcglink-apps-dsp";
+					label = "cdsp";
+					#address-cells = <1>;
+					#size-cells = <0>;
+
+					compute-cb@1 {
+						compatible = "qcom,fastrpc-compute-cb";
+						reg = <1>;
+						iommus = <&apps_smmu 0x2161 0x0400>,
+							 <&apps_smmu 0x1181 0x0420>;
+					};
+
+					compute-cb@2 {
+						compatible = "qcom,fastrpc-compute-cb";
+						reg = <2>;
+						iommus = <&apps_smmu 0x2162 0x0400>,
+							 <&apps_smmu 0x1182 0x0420>;
+					};
+
+					compute-cb@3 {
+						compatible = "qcom,fastrpc-compute-cb";
+						reg = <3>;
+						iommus = <&apps_smmu 0x2163 0x0400>,
+							 <&apps_smmu 0x1183 0x0420>;
+					};
+
+					compute-cb@4 {
+						compatible = "qcom,fastrpc-compute-cb";
+						reg = <4>;
+						iommus = <&apps_smmu 0x2164 0x0400>,
+							 <&apps_smmu 0x1184 0x0420>;
+					};
+
+					compute-cb@5 {
+						compatible = "qcom,fastrpc-compute-cb";
+						reg = <5>;
+						iommus = <&apps_smmu 0x2165 0x0400>,
+							 <&apps_smmu 0x1185 0x0420>;
+					};
+
+					compute-cb@6 {
+						compatible = "qcom,fastrpc-compute-cb";
+						reg = <6>;
+						iommus = <&apps_smmu 0x2166 0x0400>,
+							 <&apps_smmu 0x1186 0x0420>;
+					};
+
+					compute-cb@7 {
+						compatible = "qcom,fastrpc-compute-cb";
+						reg = <7>;
+						iommus = <&apps_smmu 0x2167 0x0400>,
+							 <&apps_smmu 0x1187 0x0420>;
+					};
+
+					compute-cb@8 {
+						compatible = "qcom,fastrpc-compute-cb";
+						reg = <8>;
+						iommus = <&apps_smmu 0x2168 0x0400>,
+							 <&apps_smmu 0x1188 0x0420>;
+					};
+
+					/* note: secure cb9 in downstream */
+				};
 			};
 		};
 
@@ -1203,9 +1441,7 @@
 			compatible = "qcom,sm8350-qmp-usb3-phy";
 			reg = <0 0x088e9000 0 0x200>,
 			      <0 0x088e8000 0 0x20>;
-			reg-names = "reg-base", "dp_com";
 			status = "disabled";
-			#clock-cells = <1>;
 			#address-cells = <2>;
 			#size-cells = <2>;
 			ranges;
@@ -1238,7 +1474,6 @@
 			compatible = "qcom,sm8350-qmp-usb3-uni-phy";
 			reg = <0 0x088eb000 0 0x200>;
 			status = "disabled";
-			#clock-cells = <1>;
 			#address-cells = <2>;
 			#size-cells = <2>;
 			ranges;
@@ -1381,13 +1616,14 @@
 			clocks = <&rpmhcc RPMH_CXO_CLK>;
 			clock-names = "xo";
 
-			power-domains = <&aoss_qmp AOSS_QMP_LS_LPASS>,
-					<&rpmhpd 4>,
+			power-domains = <&rpmhpd 4>,
 					<&rpmhpd 5>;
-			power-domain-names = "load_state", "lcx", "lmx";
+			power-domain-names = "lcx", "lmx";
 
 			memory-region = <&pil_adsp_mem>;
 
+			qcom,qmp = <&aoss_qmp>;
+
 			qcom,smem-states = <&smp2p_adsp_out 0>;
 			qcom,smem-state-names = "stop";
 
@@ -1402,6 +1638,32 @@
 
 				label = "lpass";
 				qcom,remote-pid = <2>;
+
+				fastrpc {
+					compatible = "qcom,fastrpc";
+					qcom,glink-channels = "fastrpcglink-apps-dsp";
+					label = "adsp";
+					#address-cells = <1>;
+					#size-cells = <0>;
+
+					compute-cb@3 {
+						compatible = "qcom,fastrpc-compute-cb";
+						reg = <3>;
+						iommus = <&apps_smmu 0x1803 0x0>;
+					};
+
+					compute-cb@4 {
+						compatible = "qcom,fastrpc-compute-cb";
+						reg = <4>;
+						iommus = <&apps_smmu 0x1804 0x0>;
+					};
+
+					compute-cb@5 {
+						compatible = "qcom,fastrpc-compute-cb";
+						reg = <5>;
+						iommus = <&apps_smmu 0x1805 0x0>;
+					};
+				};
 			};
 		};
 	};
diff --git a/arch/arm64/boot/dts/renesas/Makefile b/arch/arm64/boot/dts/renesas/Makefile
index 15a53b513966..d1c5c21d8d14 100644
--- a/arch/arm64/boot/dts/renesas/Makefile
+++ b/arch/arm64/boot/dts/renesas/Makefile
@@ -71,4 +71,6 @@ dtb-$(CONFIG_ARCH_R8A77961) += r8a779m3-salvator-xs.dtb
 dtb-$(CONFIG_ARCH_R8A77961) += r8a779m3-ulcb.dtb
 dtb-$(CONFIG_ARCH_R8A77961) += r8a779m3-ulcb-kf.dtb
 
+dtb-$(CONFIG_ARCH_R8A77965) += r8a779m5-salvator-xs.dtb
+
 dtb-$(CONFIG_ARCH_R9A07G044) += r9a07g044l2-smarc.dtb
diff --git a/arch/arm64/boot/dts/renesas/beacon-renesom-som.dtsi b/arch/arm64/boot/dts/renesas/beacon-renesom-som.dtsi
index 090dc9c4f57b..0d136809eb96 100644
--- a/arch/arm64/boot/dts/renesas/beacon-renesom-som.dtsi
+++ b/arch/arm64/boot/dts/renesas/beacon-renesom-som.dtsi
@@ -50,6 +50,7 @@
 &avb {
 	pinctrl-0 = <&avb_pins>;
 	pinctrl-names = "default";
+	phy-mode = "rgmii-rxid";
 	phy-handle = <&phy0>;
 	rx-internal-delay-ps = <1800>;
 	tx-internal-delay-ps = <2000>;
@@ -58,6 +59,8 @@
 	status = "okay";
 
 	phy0: ethernet-phy@0 {
+		compatible = "ethernet-phy-id004d.d074",
+			     "ethernet-phy-ieee802.3-c22";
 		reg = <0>;
 		interrupt-parent = <&gpio2>;
 		interrupts = <11 IRQ_TYPE_LEVEL_LOW>;
diff --git a/arch/arm64/boot/dts/renesas/cat875.dtsi b/arch/arm64/boot/dts/renesas/cat875.dtsi
index 801ea54b027c..a69d24e9c61d 100644
--- a/arch/arm64/boot/dts/renesas/cat875.dtsi
+++ b/arch/arm64/boot/dts/renesas/cat875.dtsi
@@ -21,6 +21,8 @@
 	status = "okay";
 
 	phy0: ethernet-phy@0 {
+		compatible = "ethernet-phy-id001c.c915",
+			     "ethernet-phy-ieee802.3-c22";
 		reg = <0>;
 		interrupt-parent = <&gpio2>;
 		interrupts = <21 IRQ_TYPE_LEVEL_LOW>;
diff --git a/arch/arm64/boot/dts/renesas/draak.dtsi b/arch/arm64/boot/dts/renesas/draak.dtsi
new file mode 100644
index 000000000000..eb0327c0df48
--- /dev/null
+++ b/arch/arm64/boot/dts/renesas/draak.dtsi
@@ -0,0 +1,686 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Device Tree Source for the Draak board
+ *
+ * Copyright (C) 2016-2018 Renesas Electronics Corp.
+ * Copyright (C) 2017 Glider bvba
+ */
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+
+/ {
+	model = "Renesas Draak board";
+	compatible = "renesas,draak";
+
+	aliases {
+		serial0 = &scif2;
+		ethernet0 = &avb;
+	};
+
+	audio_clkout: audio-clkout {
+		/*
+		 * This is same as <&rcar_sound 0>
+		 * but needed to avoid cs2000/rcar_sound probe dead-lock
+		 */
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <12288000>;
+	};
+
+	backlight: backlight {
+		compatible = "pwm-backlight";
+		pwms = <&pwm1 0 50000>;
+
+		brightness-levels = <512 511 505 494 473 440 392 327 241 133 0>;
+		default-brightness-level = <10>;
+
+		power-supply = <&reg_12p0v>;
+		enable-gpios = <&gpio4 0 GPIO_ACTIVE_HIGH>;
+	};
+
+	chosen {
+		bootargs = "ignore_loglevel rw root=/dev/nfs ip=on";
+		stdout-path = "serial0:115200n8";
+	};
+
+	composite-in {
+		compatible = "composite-video-connector";
+
+		port {
+			composite_con_in: endpoint {
+				remote-endpoint = <&adv7180_in>;
+			};
+		};
+	};
+
+	hdmi-in {
+		compatible = "hdmi-connector";
+		type = "a";
+
+		port {
+			hdmi_con_in: endpoint {
+				remote-endpoint = <&adv7612_in>;
+			};
+		};
+	};
+
+	hdmi-out {
+		compatible = "hdmi-connector";
+		type = "a";
+
+		port {
+			hdmi_con_out: endpoint {
+				remote-endpoint = <&adv7511_out>;
+			};
+		};
+	};
+
+	keys {
+		compatible = "gpio-keys";
+
+		pinctrl-0 = <&keys_pins>;
+		pinctrl-names = "default";
+
+		key-1 {
+			gpios = <&gpio4 12 GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_1>;
+			label = "SW56-1";
+			wakeup-source;
+			debounce-interval = <20>;
+		};
+		key-2 {
+			gpios = <&gpio4 13 GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_2>;
+			label = "SW56-2";
+			wakeup-source;
+			debounce-interval = <20>;
+		};
+		key-3 {
+			gpios = <&gpio4 14 GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_3>;
+			label = "SW56-3";
+			wakeup-source;
+			debounce-interval = <20>;
+		};
+		key-4 {
+			gpios = <&gpio4 15 GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_4>;
+			label = "SW56-4";
+			wakeup-source;
+			debounce-interval = <20>;
+		};
+	};
+
+	lvds-decoder {
+		compatible = "thine,thc63lvd1024";
+		vcc-supply = <&reg_3p3v>;
+
+		ports {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			port@0 {
+				reg = <0>;
+				thc63lvd1024_in: endpoint {
+					remote-endpoint = <&lvds0_out>;
+				};
+			};
+
+			port@2 {
+				reg = <2>;
+				thc63lvd1024_out: endpoint {
+					remote-endpoint = <&adv7511_in>;
+				};
+			};
+		};
+	};
+
+	memory@48000000 {
+		device_type = "memory";
+		/* first 128MB is reserved for secure area. */
+		reg = <0x0 0x48000000 0x0 0x18000000>;
+	};
+
+	reg_1p8v: regulator-1p8v {
+		compatible = "regulator-fixed";
+		regulator-name = "fixed-1.8V";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+		regulator-boot-on;
+		regulator-always-on;
+	};
+
+	reg_3p3v: regulator-3p3v {
+		compatible = "regulator-fixed";
+		regulator-name = "fixed-3.3V";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-boot-on;
+		regulator-always-on;
+	};
+
+	reg_12p0v: regulator-12p0v {
+		compatible = "regulator-fixed";
+		regulator-name = "D12.0V";
+		regulator-min-microvolt = <12000000>;
+		regulator-max-microvolt = <12000000>;
+		regulator-boot-on;
+		regulator-always-on;
+	};
+
+	sound_card: sound {
+		compatible = "audio-graph-card";
+
+		dais = <&rsnd_port0	/* ak4613 */
+			/* HDMI is not yet supported */
+		>;
+	};
+
+	vga {
+		compatible = "vga-connector";
+
+		port {
+			vga_in: endpoint {
+				remote-endpoint = <&adv7123_out>;
+			};
+		};
+	};
+
+	vga-encoder {
+		compatible = "adi,adv7123";
+
+		ports {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			port@0 {
+				reg = <0>;
+				adv7123_in: endpoint {
+					remote-endpoint = <&du_out_rgb>;
+				};
+			};
+			port@1 {
+				reg = <1>;
+				adv7123_out: endpoint {
+					remote-endpoint = <&vga_in>;
+				};
+			};
+		};
+	};
+
+	x12_clk: x12 {
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <74250000>;
+	};
+
+	x19_clk: x19 {
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <24576000>;
+	};
+};
+
+&audio_clk_b {
+	/*
+	 * X11 is connected to VI4_FIELD/SCIF_CLK/AUDIO_CLKB,
+	 * and R-Car Sound uses AUDIO_CLKB.
+	 * Note is that schematic indicates VI4_FIELD conection only
+	 * not AUDIO_CLKB at SoC page.
+	 * And this VI4_FIELD/SCIF_CLK/AUDIO_CLKB is connected to SW60.
+	 * SW60 should be 1-2.
+	 */
+
+	clock-frequency = <22579200>;
+};
+
+&avb {
+	pinctrl-0 = <&avb0_pins>;
+	pinctrl-names = "default";
+	renesas,no-ether-link;
+	phy-handle = <&phy0>;
+	status = "okay";
+
+	phy0: ethernet-phy@0 {
+		compatible = "ethernet-phy-id0022.1622",
+			     "ethernet-phy-ieee802.3-c22";
+		rxc-skew-ps = <1500>;
+		reg = <0>;
+		interrupt-parent = <&gpio5>;
+		interrupts = <19 IRQ_TYPE_LEVEL_LOW>;
+		reset-gpios = <&gpio5 18 GPIO_ACTIVE_LOW>;
+		/*
+		 * TX clock internal delay mode is required for reliable
+		 * 1Gbps communication using the KSZ9031RNX phy present on
+		 * the Draak board, however, TX clock internal delay mode
+		 * isn't supported on R-Car D3(e).  Thus, limit speed to
+		 * 100Mbps for reliable communication.
+		 */
+		max-speed = <100>;
+	};
+};
+
+&can0 {
+	pinctrl-0 = <&can0_pins>;
+	pinctrl-names = "default";
+	status = "okay";
+};
+
+&can1 {
+	pinctrl-0 = <&can1_pins>;
+	pinctrl-names = "default";
+	status = "okay";
+};
+
+&du {
+	pinctrl-0 = <&du_pins>;
+	pinctrl-names = "default";
+	status = "okay";
+
+	clocks = <&cpg CPG_MOD 724>,
+		 <&cpg CPG_MOD 723>,
+		 <&x12_clk>;
+	clock-names = "du.0", "du.1", "dclkin.0";
+
+	ports {
+		port@0 {
+			endpoint {
+				remote-endpoint = <&adv7123_in>;
+			};
+		};
+	};
+};
+
+&ehci0 {
+	dr_mode = "host";
+	status = "okay";
+};
+
+&extal_clk {
+	clock-frequency = <48000000>;
+};
+
+&hsusb {
+	dr_mode = "host";
+	status = "okay";
+};
+
+&i2c0 {
+	pinctrl-0 = <&i2c0_pins>;
+	pinctrl-names = "default";
+	status = "okay";
+
+	ak4613: codec@10 {
+		compatible = "asahi-kasei,ak4613";
+		#sound-dai-cells = <0>;
+		reg = <0x10>;
+		clocks = <&rcar_sound 0>; /* audio_clkout */
+
+		asahi-kasei,in1-single-end;
+		asahi-kasei,in2-single-end;
+		asahi-kasei,out1-single-end;
+		asahi-kasei,out2-single-end;
+		asahi-kasei,out3-single-end;
+		asahi-kasei,out4-single-end;
+		asahi-kasei,out5-single-end;
+		asahi-kasei,out6-single-end;
+
+		port {
+			ak4613_endpoint: endpoint {
+				remote-endpoint = <&rsnd_for_ak4613>;
+			};
+		};
+	};
+
+	composite-in@20 {
+		compatible = "adi,adv7180cp";
+		reg = <0x20>;
+
+		ports {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			port@0 {
+				reg = <0>;
+				adv7180_in: endpoint {
+					remote-endpoint = <&composite_con_in>;
+				};
+			};
+
+			port@3 {
+				reg = <3>;
+
+				/*
+				 * The VIN4 video input path is shared between
+				 * CVBS and HDMI inputs through SW[49-53]
+				 * switches.
+				 *
+				 * CVBS is the default selection, link it to
+				 * VIN4 here.
+				 */
+				adv7180_out: endpoint {
+					remote-endpoint = <&vin4_in>;
+				};
+			};
+		};
+
+	};
+
+	hdmi-encoder@39 {
+		compatible = "adi,adv7511w";
+		reg = <0x39>, <0x3f>, <0x3c>, <0x38>;
+		reg-names = "main", "edid", "cec", "packet";
+		interrupt-parent = <&gpio1>;
+		interrupts = <28 IRQ_TYPE_LEVEL_LOW>;
+
+		adi,input-depth = <8>;
+		adi,input-colorspace = "rgb";
+		adi,input-clock = "1x";
+
+		ports {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			port@0 {
+				reg = <0>;
+				adv7511_in: endpoint {
+					remote-endpoint = <&thc63lvd1024_out>;
+				};
+			};
+
+			port@1 {
+				reg = <1>;
+				adv7511_out: endpoint {
+					remote-endpoint = <&hdmi_con_out>;
+				};
+			};
+		};
+	};
+
+	hdmi-decoder@4c {
+		compatible = "adi,adv7612";
+		reg = <0x4c>;
+		default-input = <0>;
+
+		ports {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			port@0 {
+				reg = <0>;
+
+				adv7612_in: endpoint {
+					remote-endpoint = <&hdmi_con_in>;
+				};
+			};
+
+			port@2 {
+				reg = <2>;
+
+				/*
+				 * The VIN4 video input path is shared between
+				 * CVBS and HDMI inputs through SW[49-53]
+				 * switches.
+				 *
+				 * CVBS is the default selection, leave HDMI
+				 * not connected here.
+				 */
+				adv7612_out: endpoint {
+					pclk-sample = <0>;
+					hsync-active = <0>;
+					vsync-active = <0>;
+				};
+			};
+		};
+	};
+
+	cs2000: clk-multiplier@4f {
+		#clock-cells = <0>;
+		compatible = "cirrus,cs2000-cp";
+		reg = <0x4f>;
+		clocks = <&audio_clkout>, <&x19_clk>; /* audio_clkout_1, x19 */
+		clock-names = "clk_in", "ref_clk";
+
+		assigned-clocks = <&cs2000>;
+		assigned-clock-rates = <24576000>; /* 1/1 divide */
+	};
+
+	eeprom@50 {
+		compatible = "rohm,br24t01", "atmel,24c01";
+		reg = <0x50>;
+		pagesize = <8>;
+	};
+};
+
+&i2c1 {
+	pinctrl-0 = <&i2c1_pins>;
+	pinctrl-names = "default";
+	status = "okay";
+};
+
+&lvds0 {
+	status = "okay";
+
+	clocks = <&cpg CPG_MOD 727>,
+		 <&x12_clk>,
+		 <&extal_clk>;
+	clock-names = "fck", "dclkin.0", "extal";
+
+	ports {
+		port@1 {
+			lvds0_out: endpoint {
+				remote-endpoint = <&thc63lvd1024_in>;
+			};
+		};
+	};
+};
+
+&lvds1 {
+	/*
+	 * Even though the LVDS1 output is not connected, the encoder must be
+	 * enabled to supply a pixel clock to the DU for the DPAD output when
+	 * LVDS0 is in use.
+	 */
+	status = "okay";
+
+	clocks = <&cpg CPG_MOD 727>,
+		 <&x12_clk>,
+		 <&extal_clk>;
+	clock-names = "fck", "dclkin.0", "extal";
+};
+
+&ohci0 {
+	dr_mode = "host";
+	status = "okay";
+};
+
+&pfc {
+	avb0_pins: avb {
+		groups = "avb0_link", "avb0_mdio", "avb0_mii";
+		function = "avb0";
+	};
+
+	can0_pins: can0 {
+		groups = "can0_data_a";
+		function = "can0";
+	};
+
+	can1_pins: can1 {
+		groups = "can1_data_a";
+		function = "can1";
+	};
+
+	du_pins: du {
+		groups = "du_rgb888", "du_sync", "du_disp", "du_clk_out_0";
+		function = "du";
+	};
+
+	i2c0_pins: i2c0 {
+		groups = "i2c0";
+		function = "i2c0";
+	};
+
+	i2c1_pins: i2c1 {
+		groups = "i2c1";
+		function = "i2c1";
+	};
+
+	keys_pins: keys {
+		pins = "GP_4_12", "GP_4_13", "GP_4_14", "GP_4_15";
+		bias-pull-up;
+	};
+
+	pwm0_pins: pwm0 {
+		groups = "pwm0_c";
+		function = "pwm0";
+	};
+
+	pwm1_pins: pwm1 {
+		groups = "pwm1_c";
+		function = "pwm1";
+	};
+
+	scif2_pins: scif2 {
+		groups = "scif2_data";
+		function = "scif2";
+	};
+
+	sdhi2_pins: sd2 {
+		groups = "mmc_data8", "mmc_ctrl";
+		function = "mmc";
+		power-source = <1800>;
+	};
+
+	sdhi2_pins_uhs: sd2_uhs {
+		groups = "mmc_data8", "mmc_ctrl";
+		function = "mmc";
+		power-source = <1800>;
+	};
+
+	sound_pins: sound {
+		groups = "ssi34_ctrl", "ssi3_data", "ssi4_data_a";
+		function = "ssi";
+	};
+
+	sound_clk_pins: sound-clk {
+		groups = "audio_clk_a", "audio_clk_b",
+			 "audio_clkout", "audio_clkout1";
+		function = "audio_clk";
+	};
+
+	usb0_pins: usb0 {
+		groups = "usb0";
+		function = "usb0";
+	};
+
+	vin4_pins_cvbs: vin4 {
+		groups = "vin4_data8", "vin4_sync", "vin4_clk";
+		function = "vin4";
+	};
+};
+
+&pwm0 {
+	pinctrl-0 = <&pwm0_pins>;
+	pinctrl-names = "default";
+
+	status = "okay";
+};
+
+&pwm1 {
+	pinctrl-0 = <&pwm1_pins>;
+	pinctrl-names = "default";
+
+	status = "okay";
+};
+
+&rcar_sound {
+	pinctrl-0 = <&sound_pins>, <&sound_clk_pins>;
+	pinctrl-names = "default";
+
+	/* Single DAI */
+	#sound-dai-cells = <0>;
+
+	/* audio_clkout0/1 */
+	#clock-cells = <1>;
+	clock-frequency = <12288000 11289600>;
+
+	status = "okay";
+
+	clocks = <&cpg CPG_MOD 1005>,
+		 <&cpg CPG_MOD 1011>, <&cpg CPG_MOD 1012>,
+		 <&cpg CPG_MOD 1025>, <&cpg CPG_MOD 1026>,
+		 <&cpg CPG_MOD 1020>, <&cpg CPG_MOD 1021>,
+		 <&cpg CPG_MOD 1020>, <&cpg CPG_MOD 1021>,
+		 <&cpg CPG_MOD 1019>, <&cpg CPG_MOD 1018>,
+		 <&cs2000>, <&audio_clk_b>,
+		 <&cpg CPG_CORE R8A77995_CLK_ZA2>;
+
+	ports {
+		rsnd_port0: port {
+			rsnd_for_ak4613: endpoint {
+				remote-endpoint = <&ak4613_endpoint>;
+				dai-format = "left_j";
+				bitclock-master = <&rsnd_for_ak4613>;
+				frame-master = <&rsnd_for_ak4613>;
+				playback = <&ssi3>, <&src5>, <&dvc0>;
+				capture  = <&ssi4>, <&src6>, <&dvc1>;
+			};
+		};
+	};
+};
+
+&rwdt {
+	timeout-sec = <60>;
+	status = "okay";
+};
+
+&scif2 {
+	pinctrl-0 = <&scif2_pins>;
+	pinctrl-names = "default";
+
+	status = "okay";
+};
+
+&sdhi2 {
+	/* used for on-board eMMC */
+	pinctrl-0 = <&sdhi2_pins>;
+	pinctrl-1 = <&sdhi2_pins_uhs>;
+	pinctrl-names = "default", "state_uhs";
+
+	vmmc-supply = <&reg_3p3v>;
+	vqmmc-supply = <&reg_1p8v>;
+	bus-width = <8>;
+	mmc-hs200-1_8v;
+	no-sd;
+	no-sdio;
+	non-removable;
+	status = "okay";
+};
+
+&ssi4 {
+	shared-pin;
+};
+
+&usb2_phy0 {
+	pinctrl-0 = <&usb0_pins>;
+	pinctrl-names = "default";
+
+	renesas,no-otg-pins;
+	status = "okay";
+};
+
+&vin4 {
+	pinctrl-0 = <&vin4_pins_cvbs>;
+	pinctrl-names = "default";
+
+	status = "okay";
+
+	ports {
+		port {
+			vin4_in: endpoint {
+				remote-endpoint = <&adv7180_out>;
+			};
+		};
+	};
+};
diff --git a/arch/arm64/boot/dts/renesas/ebisu.dtsi b/arch/arm64/boot/dts/renesas/ebisu.dtsi
new file mode 100644
index 000000000000..67231c8576c5
--- /dev/null
+++ b/arch/arm64/boot/dts/renesas/ebisu.dtsi
@@ -0,0 +1,803 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Device Tree Source for the Ebisu board
+ *
+ * Copyright (C) 2018 Renesas Electronics Corp.
+ */
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+
+/ {
+	model = "Renesas Ebisu board";
+	compatible = "renesas,ebisu";
+
+	aliases {
+		serial0 = &scif2;
+		ethernet0 = &avb;
+		mmc0 = &sdhi3;
+		mmc1 = &sdhi0;
+		mmc2 = &sdhi1;
+	};
+
+	chosen {
+		bootargs = "ignore_loglevel rw root=/dev/nfs ip=on";
+		stdout-path = "serial0:115200n8";
+	};
+
+	audio_clkout: audio-clkout {
+		/*
+		 * This is same as <&rcar_sound 0>
+		 * but needed to avoid cs2000/rcar_sound probe dead-lock
+		 */
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <11289600>;
+	};
+
+	backlight: backlight {
+		compatible = "pwm-backlight";
+		pwms = <&pwm3 0 50000>;
+
+		brightness-levels = <512 511 505 494 473 440 392 327 241 133 0>;
+		default-brightness-level = <10>;
+
+		power-supply = <&reg_12p0v>;
+	};
+
+	cvbs-in {
+		compatible = "composite-video-connector";
+		label = "CVBS IN";
+
+		port {
+			cvbs_con: endpoint {
+				remote-endpoint = <&adv7482_ain7>;
+			};
+		};
+	};
+
+	hdmi-in {
+		compatible = "hdmi-connector";
+		label = "HDMI IN";
+		type = "a";
+
+		port {
+			hdmi_in_con: endpoint {
+				remote-endpoint = <&adv7482_hdmi>;
+			};
+		};
+	};
+
+	hdmi-out {
+		compatible = "hdmi-connector";
+		type = "a";
+
+		port {
+			hdmi_con_out: endpoint {
+				remote-endpoint = <&adv7511_out>;
+			};
+		};
+	};
+
+	keys {
+		compatible = "gpio-keys";
+
+		pinctrl-0 = <&keys_pins>;
+		pinctrl-names = "default";
+
+		key-1 {
+			gpios = <&gpio5 10 GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_1>;
+			label = "SW4-1";
+			wakeup-source;
+			debounce-interval = <20>;
+		};
+		key-2 {
+			gpios = <&gpio5 11 GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_2>;
+			label = "SW4-2";
+			wakeup-source;
+			debounce-interval = <20>;
+		};
+		key-3 {
+			gpios = <&gpio5 12 GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_3>;
+			label = "SW4-3";
+			wakeup-source;
+			debounce-interval = <20>;
+		};
+		key-4 {
+			gpios = <&gpio5 13 GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_4>;
+			label = "SW4-4";
+			wakeup-source;
+			debounce-interval = <20>;
+		};
+	};
+
+	lvds-decoder {
+		compatible = "thine,thc63lvd1024";
+		vcc-supply = <&reg_3p3v>;
+
+		ports {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			port@0 {
+				reg = <0>;
+				thc63lvd1024_in: endpoint {
+					remote-endpoint = <&lvds0_out>;
+				};
+			};
+
+			port@2 {
+				reg = <2>;
+				thc63lvd1024_out: endpoint {
+					remote-endpoint = <&adv7511_in>;
+				};
+			};
+		};
+	};
+
+	memory@48000000 {
+		device_type = "memory";
+		/* first 128MB is reserved for secure area. */
+		reg = <0x0 0x48000000 0x0 0x38000000>;
+	};
+
+	reg_1p8v: regulator0 {
+		compatible = "regulator-fixed";
+		regulator-name = "fixed-1.8V";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+		regulator-boot-on;
+		regulator-always-on;
+	};
+
+	reg_3p3v: regulator1 {
+		compatible = "regulator-fixed";
+		regulator-name = "fixed-3.3V";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-boot-on;
+		regulator-always-on;
+	};
+
+	reg_12p0v: regulator2 {
+		compatible = "regulator-fixed";
+		regulator-name = "D12.0V";
+		regulator-min-microvolt = <12000000>;
+		regulator-max-microvolt = <12000000>;
+		regulator-boot-on;
+		regulator-always-on;
+	};
+
+	rsnd_ak4613: sound {
+		compatible = "simple-audio-card";
+
+		simple-audio-card,name = "rsnd-ak4613";
+		simple-audio-card,format = "left_j";
+		simple-audio-card,bitclock-master = <&sndcpu>;
+		simple-audio-card,frame-master = <&sndcpu>;
+
+		sndcodec: simple-audio-card,codec {
+			sound-dai = <&ak4613>;
+		};
+
+		sndcpu: simple-audio-card,cpu {
+			sound-dai = <&rcar_sound>;
+		};
+	};
+
+	vbus0_usb2: regulator-vbus0-usb2 {
+		compatible = "regulator-fixed";
+
+		regulator-name = "USB20_VBUS_CN";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+
+		gpio = <&gpio6 4 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+	};
+
+	vcc_sdhi0: regulator-vcc-sdhi0 {
+		compatible = "regulator-fixed";
+
+		regulator-name = "SDHI0 Vcc";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+
+		gpio = <&gpio5 17 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+	};
+
+	vccq_sdhi0: regulator-vccq-sdhi0 {
+		compatible = "regulator-gpio";
+
+		regulator-name = "SDHI0 VccQ";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <3300000>;
+
+		gpios = <&gpio5 18 GPIO_ACTIVE_HIGH>;
+		gpios-states = <1>;
+		states = <3300000 1>, <1800000 0>;
+	};
+
+	vcc_sdhi1: regulator-vcc-sdhi1 {
+		compatible = "regulator-fixed";
+
+		regulator-name = "SDHI1 Vcc";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+
+		gpio = <&gpio0 4 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+	};
+
+	vccq_sdhi1: regulator-vccq-sdhi1 {
+		compatible = "regulator-gpio";
+
+		regulator-name = "SDHI1 VccQ";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <3300000>;
+
+		gpios = <&gpio3 15 GPIO_ACTIVE_HIGH>;
+		gpios-states = <1>;
+		states = <3300000 1>, <1800000 0>;
+	};
+
+	vga {
+		compatible = "vga-connector";
+
+		port {
+			vga_in: endpoint {
+				remote-endpoint = <&adv7123_out>;
+			};
+		};
+	};
+
+	vga-encoder {
+		compatible = "adi,adv7123";
+
+		ports {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			port@0 {
+				reg = <0>;
+				adv7123_in: endpoint {
+					remote-endpoint = <&du_out_rgb>;
+				};
+			};
+			port@1 {
+				reg = <1>;
+				adv7123_out: endpoint {
+					remote-endpoint = <&vga_in>;
+				};
+			};
+		};
+	};
+
+	x12_clk: x12 {
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <24576000>;
+	};
+
+	x13_clk: x13 {
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <74250000>;
+	};
+};
+
+&audio_clk_a {
+	clock-frequency = <22579200>;
+};
+
+&avb {
+	pinctrl-0 = <&avb_pins>;
+	pinctrl-names = "default";
+	phy-handle = <&phy0>;
+	status = "okay";
+
+	phy0: ethernet-phy@0 {
+		compatible = "ethernet-phy-id0022.1622",
+			     "ethernet-phy-ieee802.3-c22";
+		rxc-skew-ps = <1500>;
+		reg = <0>;
+		interrupt-parent = <&gpio2>;
+		interrupts = <21 IRQ_TYPE_LEVEL_LOW>;
+		reset-gpios = <&gpio1 20 GPIO_ACTIVE_LOW>;
+		/*
+		 * TX clock internal delay mode is required for reliable
+		 * 1Gbps communication using the KSZ9031RNX phy present on
+		 * the Ebisu board, however, TX clock internal delay mode
+		 * isn't supported on R-Car E3(e).  Thus, limit speed to
+		 * 100Mbps for reliable communication.
+		 */
+		max-speed = <100>;
+	};
+};
+
+&canfd {
+	pinctrl-0 = <&canfd0_pins>;
+	pinctrl-names = "default";
+	status = "okay";
+
+	channel0 {
+		status = "okay";
+	};
+};
+
+&csi40 {
+	status = "okay";
+
+	ports {
+		port@0 {
+			csi40_in: endpoint {
+				clock-lanes = <0>;
+				data-lanes = <1 2>;
+				remote-endpoint = <&adv7482_txa>;
+			};
+		};
+	};
+};
+
+&du {
+	pinctrl-0 = <&du_pins>;
+	pinctrl-names = "default";
+	status = "okay";
+
+	clocks = <&cpg CPG_MOD 724>,
+		 <&cpg CPG_MOD 723>,
+		 <&x13_clk>;
+	clock-names = "du.0", "du.1", "dclkin.0";
+
+	ports {
+		port@0 {
+			endpoint {
+				remote-endpoint = <&adv7123_in>;
+			};
+		};
+	};
+};
+
+&ehci0 {
+	dr_mode = "otg";
+	status = "okay";
+};
+
+&extal_clk {
+	clock-frequency = <48000000>;
+};
+
+&hsusb {
+	dr_mode = "otg";
+	status = "okay";
+};
+
+&i2c0 {
+	status = "okay";
+
+	io_expander: gpio@20 {
+		compatible = "onnn,pca9654";
+		reg = <0x20>;
+		gpio-controller;
+		#gpio-cells = <2>;
+		interrupt-parent = <&gpio2>;
+		interrupts = <22 IRQ_TYPE_LEVEL_LOW>;
+	};
+
+	hdmi-encoder@39 {
+		compatible = "adi,adv7511w";
+		reg = <0x39>;
+		interrupt-parent = <&gpio1>;
+		interrupts = <1 IRQ_TYPE_LEVEL_LOW>;
+
+		adi,input-depth = <8>;
+		adi,input-colorspace = "rgb";
+		adi,input-clock = "1x";
+
+		ports {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			port@0 {
+				reg = <0>;
+				adv7511_in: endpoint {
+					remote-endpoint = <&thc63lvd1024_out>;
+				};
+			};
+
+			port@1 {
+				reg = <1>;
+				adv7511_out: endpoint {
+					remote-endpoint = <&hdmi_con_out>;
+				};
+			};
+		};
+	};
+
+	video-receiver@70 {
+		compatible = "adi,adv7482";
+		reg = <0x70>;
+
+		interrupt-parent = <&gpio0>;
+		interrupt-names = "intrq1", "intrq2";
+		interrupts = <7 IRQ_TYPE_LEVEL_LOW>,
+			     <17 IRQ_TYPE_LEVEL_LOW>;
+
+		ports {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			port@7 {
+				reg = <7>;
+
+				adv7482_ain7: endpoint {
+					remote-endpoint = <&cvbs_con>;
+				};
+			};
+
+			port@8 {
+				reg = <8>;
+
+				adv7482_hdmi: endpoint {
+					remote-endpoint = <&hdmi_in_con>;
+				};
+			};
+
+			port@a {
+				reg = <10>;
+
+				adv7482_txa: endpoint {
+					clock-lanes = <0>;
+					data-lanes = <1 2>;
+					remote-endpoint = <&csi40_in>;
+				};
+			};
+		};
+	};
+};
+
+&i2c3 {
+	status = "okay";
+
+	ak4613: codec@10 {
+		compatible = "asahi-kasei,ak4613";
+		#sound-dai-cells = <0>;
+		reg = <0x10>;
+		clocks = <&rcar_sound 3>;
+
+		asahi-kasei,in1-single-end;
+		asahi-kasei,in2-single-end;
+		asahi-kasei,out1-single-end;
+		asahi-kasei,out2-single-end;
+		asahi-kasei,out3-single-end;
+		asahi-kasei,out4-single-end;
+		asahi-kasei,out5-single-end;
+		asahi-kasei,out6-single-end;
+	};
+
+	cs2000: clk-multiplier@4f {
+		#clock-cells = <0>;
+		compatible = "cirrus,cs2000-cp";
+		reg = <0x4f>;
+		clocks = <&audio_clkout>, <&x12_clk>;
+		clock-names = "clk_in", "ref_clk";
+
+		assigned-clocks = <&cs2000>;
+		assigned-clock-rates = <24576000>; /* 1/1 divide */
+	};
+};
+
+&i2c_dvfs {
+	status = "okay";
+
+	clock-frequency = <400000>;
+
+	pmic: pmic@30 {
+		pinctrl-0 = <&irq0_pins>;
+		pinctrl-names = "default";
+
+		compatible = "rohm,bd9571mwv";
+		reg = <0x30>;
+		interrupt-parent = <&intc_ex>;
+		interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
+		interrupt-controller;
+		#interrupt-cells = <2>;
+		gpio-controller;
+		#gpio-cells = <2>;
+		rohm,ddr-backup-power = <0x1>;
+		rohm,rstbmode-level;
+	};
+
+	eeprom@50 {
+		compatible = "rohm,br24t01", "atmel,24c01";
+		reg = <0x50>;
+		pagesize = <8>;
+	};
+};
+
+&lvds0 {
+	status = "okay";
+
+	clocks = <&cpg CPG_MOD 727>,
+		 <&x13_clk>,
+		 <&extal_clk>;
+	clock-names = "fck", "dclkin.0", "extal";
+
+	ports {
+		port@1 {
+			lvds0_out: endpoint {
+				remote-endpoint = <&thc63lvd1024_in>;
+			};
+		};
+	};
+};
+
+&lvds1 {
+	/*
+	 * Even though the LVDS1 output is not connected, the encoder must be
+	 * enabled to supply a pixel clock to the DU for the DPAD output when
+	 * LVDS0 is in use.
+	 */
+	status = "okay";
+
+	clocks = <&cpg CPG_MOD 727>,
+		 <&x13_clk>,
+		 <&extal_clk>;
+	clock-names = "fck", "dclkin.0", "extal";
+};
+
+&ohci0 {
+	dr_mode = "otg";
+	status = "okay";
+};
+
+&pcie_bus_clk {
+	clock-frequency = <100000000>;
+};
+
+&pciec0 {
+	status = "okay";
+};
+
+&pfc {
+	avb_pins: avb {
+		groups = "avb_link", "avb_mii";
+		function = "avb";
+	};
+
+	canfd0_pins: canfd0 {
+		groups = "canfd0_data";
+		function = "canfd0";
+	};
+
+	du_pins: du {
+		groups = "du_rgb888", "du_sync", "du_disp", "du_clk_out_0";
+		function = "du";
+	};
+
+	irq0_pins: irq0 {
+		groups = "intc_ex_irq0";
+		function = "intc_ex";
+	};
+
+	keys_pins: keys {
+		pins = "GP_5_10", "GP_5_11", "GP_5_12", "GP_5_13";
+		bias-pull-up;
+	};
+
+	pwm3_pins: pwm3 {
+		groups = "pwm3_b";
+		function = "pwm3";
+	};
+
+	pwm5_pins: pwm5 {
+		groups = "pwm5_a";
+		function = "pwm5";
+	};
+
+	scif2_pins: scif2 {
+		groups = "scif2_data_a";
+		function = "scif2";
+	};
+
+	sdhi0_pins: sd0 {
+		groups = "sdhi0_data4", "sdhi0_ctrl";
+		function = "sdhi0";
+		power-source = <3300>;
+	};
+
+	sdhi0_pins_uhs: sd0_uhs {
+		groups = "sdhi0_data4", "sdhi0_ctrl";
+		function = "sdhi0";
+		power-source = <1800>;
+	};
+
+	sdhi1_pins: sd1 {
+		groups = "sdhi1_data4", "sdhi1_ctrl";
+		function = "sdhi1";
+		power-source = <3300>;
+	};
+
+	sdhi1_pins_uhs: sd1_uhs {
+		groups = "sdhi1_data4", "sdhi1_ctrl";
+		function = "sdhi1";
+		power-source = <1800>;
+	};
+
+	sdhi3_pins: sd3 {
+		groups = "sdhi3_data8", "sdhi3_ctrl", "sdhi3_ds";
+		function = "sdhi3";
+		power-source = <1800>;
+	};
+
+	sound_clk_pins: sound_clk {
+		groups = "audio_clk_a", "audio_clk_b_a", "audio_clk_c_a",
+			 "audio_clkout_a", "audio_clkout1_a";
+		function = "audio_clk";
+	};
+
+	sound_pins: sound {
+		groups = "ssi01239_ctrl", "ssi0_data", "ssi1_data";
+		function = "ssi";
+	};
+
+	usb0_pins: usb {
+		groups = "usb0_b", "usb0_id";
+		function = "usb0";
+	};
+
+	usb30_pins: usb30 {
+		groups = "usb30";
+		function = "usb30";
+	};
+};
+
+&pwm3 {
+	pinctrl-0 = <&pwm3_pins>;
+	pinctrl-names = "default";
+
+	status = "okay";
+};
+
+&pwm5 {
+	pinctrl-0 = <&pwm5_pins>;
+	pinctrl-names = "default";
+
+	status = "okay";
+};
+
+&rcar_sound {
+	pinctrl-0 = <&sound_pins>, <&sound_clk_pins>;
+	pinctrl-names = "default";
+
+	/* Single DAI */
+	#sound-dai-cells = <0>;
+
+	/* audio_clkout0/1/2/3 */
+	#clock-cells = <1>;
+	clock-frequency = <12288000 11289600>;
+
+	status = "okay";
+
+	/* update <audio_clk_b> to <cs2000> */
+	clocks = <&cpg CPG_MOD 1005>,
+		 <&cpg CPG_MOD 1006>, <&cpg CPG_MOD 1007>,
+		 <&cpg CPG_MOD 1008>, <&cpg CPG_MOD 1009>,
+		 <&cpg CPG_MOD 1010>, <&cpg CPG_MOD 1011>,
+		 <&cpg CPG_MOD 1012>, <&cpg CPG_MOD 1013>,
+		 <&cpg CPG_MOD 1014>, <&cpg CPG_MOD 1015>,
+		 <&cpg CPG_MOD 1022>, <&cpg CPG_MOD 1023>,
+		 <&cpg CPG_MOD 1024>, <&cpg CPG_MOD 1025>,
+		 <&cpg CPG_MOD 1026>, <&cpg CPG_MOD 1027>,
+		 <&cpg CPG_MOD 1028>, <&cpg CPG_MOD 1029>,
+		 <&cpg CPG_MOD 1030>, <&cpg CPG_MOD 1031>,
+		 <&cpg CPG_MOD 1020>, <&cpg CPG_MOD 1021>,
+		 <&cpg CPG_MOD 1020>, <&cpg CPG_MOD 1021>,
+		 <&cpg CPG_MOD 1019>, <&cpg CPG_MOD 1018>,
+		 <&audio_clk_a>, <&cs2000>, <&audio_clk_c>,
+		 <&cpg CPG_CORE R8A77990_CLK_ZA2>;
+
+	rcar_sound,dai {
+		dai0 {
+			playback = <&ssi0>, <&src0>, <&dvc0>;
+			capture  = <&ssi1>, <&src1>, <&dvc1>;
+		};
+	};
+
+};
+
+&rwdt {
+	timeout-sec = <60>;
+	status = "okay";
+};
+
+&scif2 {
+	pinctrl-0 = <&scif2_pins>;
+	pinctrl-names = "default";
+
+	status = "okay";
+};
+
+&sdhi0 {
+	pinctrl-0 = <&sdhi0_pins>;
+	pinctrl-1 = <&sdhi0_pins_uhs>;
+	pinctrl-names = "default", "state_uhs";
+
+	vmmc-supply = <&vcc_sdhi0>;
+	vqmmc-supply = <&vccq_sdhi0>;
+	cd-gpios = <&gpio3 12 GPIO_ACTIVE_LOW>;
+	wp-gpios = <&gpio3 13 GPIO_ACTIVE_HIGH>;
+	bus-width = <4>;
+	sd-uhs-sdr50;
+	sd-uhs-sdr104;
+	status = "okay";
+};
+
+&sdhi1 {
+	pinctrl-0 = <&sdhi1_pins>;
+	pinctrl-1 = <&sdhi1_pins_uhs>;
+	pinctrl-names = "default", "state_uhs";
+
+	vmmc-supply = <&vcc_sdhi1>;
+	vqmmc-supply = <&vccq_sdhi1>;
+	cd-gpios = <&gpio3 14 GPIO_ACTIVE_LOW>;
+	bus-width = <4>;
+	sd-uhs-sdr50;
+	sd-uhs-sdr104;
+	status = "okay";
+};
+
+&sdhi3 {
+	/* used for on-board 8bit eMMC */
+	pinctrl-0 = <&sdhi3_pins>;
+	pinctrl-1 = <&sdhi3_pins>;
+	pinctrl-names = "default", "state_uhs";
+
+	vmmc-supply = <&reg_3p3v>;
+	vqmmc-supply = <&reg_1p8v>;
+	mmc-hs200-1_8v;
+	mmc-hs400-1_8v;
+	bus-width = <8>;
+	no-sd;
+	no-sdio;
+	non-removable;
+	full-pwr-cycle-in-suspend;
+	status = "okay";
+};
+
+&ssi1 {
+	shared-pin;
+};
+
+&usb2_phy0 {
+	pinctrl-0 = <&usb0_pins>;
+	pinctrl-names = "default";
+
+	vbus-supply = <&vbus0_usb2>;
+	status = "okay";
+};
+
+&usb3_peri0 {
+	companion = <&xhci0>;
+	status = "okay";
+};
+
+&vin4 {
+	status = "okay";
+};
+
+&vin5 {
+	status = "okay";
+};
+
+&xhci0 {
+	pinctrl-0 = <&usb30_pins>;
+	pinctrl-names = "default";
+
+	status = "okay";
+};
diff --git a/arch/arm64/boot/dts/renesas/hihope-rzg2-ex.dtsi b/arch/arm64/boot/dts/renesas/hihope-rzg2-ex.dtsi
index dde3a07bc417..ad898c6db4e6 100644
--- a/arch/arm64/boot/dts/renesas/hihope-rzg2-ex.dtsi
+++ b/arch/arm64/boot/dts/renesas/hihope-rzg2-ex.dtsi
@@ -24,6 +24,8 @@
 	status = "okay";
 
 	phy0: ethernet-phy@0 {
+		compatible = "ethernet-phy-id001c.c915",
+			     "ethernet-phy-ieee802.3-c22";
 		reg = <0>;
 		interrupt-parent = <&gpio2>;
 		interrupts = <11 IRQ_TYPE_LEVEL_LOW>;
diff --git a/arch/arm64/boot/dts/renesas/r8a77961.dtsi b/arch/arm64/boot/dts/renesas/r8a77961.dtsi
index 041473aa5cd0..86d59e7e1a87 100644
--- a/arch/arm64/boot/dts/renesas/r8a77961.dtsi
+++ b/arch/arm64/boot/dts/renesas/r8a77961.dtsi
@@ -1392,6 +1392,17 @@
 			status = "disabled";
 		};
 
+		tpu: pwm@e6e80000 {
+			compatible = "renesas,tpu-r8a77961", "renesas,tpu";
+			reg = <0 0xe6e80000 0 0x148>;
+			interrupts = <GIC_SPI 135 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&cpg CPG_MOD 304>;
+			power-domains = <&sysc R8A77961_PD_ALWAYS_ON>;
+			resets = <&cpg 304>;
+			#pwm-cells = <3>;
+			status = "disabled";
+		};
+
 		msiof0: spi@e6e90000 {
 			compatible = "renesas,msiof-r8a77961",
 				     "renesas,rcar-gen3-msiof";
diff --git a/arch/arm64/boot/dts/renesas/r8a77970-eagle.dts b/arch/arm64/boot/dts/renesas/r8a77970-eagle.dts
index d24da54f312b..b579d3189a93 100644
--- a/arch/arm64/boot/dts/renesas/r8a77970-eagle.dts
+++ b/arch/arm64/boot/dts/renesas/r8a77970-eagle.dts
@@ -8,6 +8,7 @@
 
 /dts-v1/;
 #include "r8a77970.dtsi"
+#include <dt-bindings/gpio/gpio.h>
 
 / {
 	model = "Renesas Eagle board based on r8a77970";
@@ -92,10 +93,13 @@
 	status = "okay";
 
 	phy0: ethernet-phy@0 {
+		compatible = "ethernet-phy-id0022.1622",
+			     "ethernet-phy-ieee802.3-c22";
 		rxc-skew-ps = <1500>;
 		reg = <0>;
 		interrupt-parent = <&gpio1>;
 		interrupts = <17 IRQ_TYPE_LEVEL_LOW>;
+		reset-gpios = <&gpio1 16 GPIO_ACTIVE_LOW>;
 	};
 };
 
diff --git a/arch/arm64/boot/dts/renesas/r8a77970-v3msk.dts b/arch/arm64/boot/dts/renesas/r8a77970-v3msk.dts
index 2426e533128c..39f3e6cbba3d 100644
--- a/arch/arm64/boot/dts/renesas/r8a77970-v3msk.dts
+++ b/arch/arm64/boot/dts/renesas/r8a77970-v3msk.dts
@@ -8,6 +8,7 @@
 
 /dts-v1/;
 #include "r8a77970.dtsi"
+#include <dt-bindings/gpio/gpio.h>
 
 / {
 	model = "Renesas V3M Starter Kit board";
@@ -107,10 +108,13 @@
 	status = "okay";
 
 	phy0: ethernet-phy@0 {
+		compatible = "ethernet-phy-id0022.1622",
+			     "ethernet-phy-ieee802.3-c22";
 		rxc-skew-ps = <1500>;
 		reg = <0>;
 		interrupt-parent = <&gpio1>;
 		interrupts = <17 IRQ_TYPE_LEVEL_LOW>;
+		reset-gpios = <&gpio1 16 GPIO_ACTIVE_LOW>;
 	};
 };
 
diff --git a/arch/arm64/boot/dts/renesas/r8a77980-condor.dts b/arch/arm64/boot/dts/renesas/r8a77980-condor.dts
index edf7f2a2f958..3d6d10c82f48 100644
--- a/arch/arm64/boot/dts/renesas/r8a77980-condor.dts
+++ b/arch/arm64/boot/dts/renesas/r8a77980-condor.dts
@@ -8,6 +8,7 @@
 
 /dts-v1/;
 #include "r8a77980.dtsi"
+#include <dt-bindings/gpio/gpio.h>
 
 / {
 	model = "Renesas Condor board based on r8a77980";
@@ -132,10 +133,13 @@
 	status = "okay";
 
 	phy0: ethernet-phy@0 {
+		compatible = "ethernet-phy-id0022.1622",
+			     "ethernet-phy-ieee802.3-c22";
 		rxc-skew-ps = <1500>;
 		reg = <0>;
 		interrupt-parent = <&gpio4>;
 		interrupts = <23 IRQ_TYPE_LEVEL_LOW>;
+		reset-gpios = <&gpio4 22 GPIO_ACTIVE_LOW>;
 	};
 };
 
diff --git a/arch/arm64/boot/dts/renesas/r8a77980-v3hsk.dts b/arch/arm64/boot/dts/renesas/r8a77980-v3hsk.dts
index 7838dcee3136..1d09d8867651 100644
--- a/arch/arm64/boot/dts/renesas/r8a77980-v3hsk.dts
+++ b/arch/arm64/boot/dts/renesas/r8a77980-v3hsk.dts
@@ -8,6 +8,7 @@
 
 /dts-v1/;
 #include "r8a77980.dtsi"
+#include <dt-bindings/gpio/gpio.h>
 
 / {
 	model = "Renesas V3H Starter Kit board";
@@ -113,9 +114,12 @@
 	status = "okay";
 
 	phy0: ethernet-phy@0 {
+		compatible = "ethernet-phy-id0022.1622",
+			     "ethernet-phy-ieee802.3-c22";
 		reg = <0>;
 		interrupt-parent = <&gpio4>;
 		interrupts = <23 IRQ_TYPE_LEVEL_LOW>;
+		reset-gpios = <&gpio4 22 GPIO_ACTIVE_LOW>;
 	};
 };
 
diff --git a/arch/arm64/boot/dts/renesas/r8a77990-ebisu.dts b/arch/arm64/boot/dts/renesas/r8a77990-ebisu.dts
index 9c7146084ea1..9da0fd08f8c4 100644
--- a/arch/arm64/boot/dts/renesas/r8a77990-ebisu.dts
+++ b/arch/arm64/boot/dts/renesas/r8a77990-ebisu.dts
@@ -7,795 +7,9 @@
 
 /dts-v1/;
 #include "r8a77990.dtsi"
-#include <dt-bindings/gpio/gpio.h>
-#include <dt-bindings/input/input.h>
+#include "ebisu.dtsi"
 
 / {
 	model = "Renesas Ebisu board based on r8a77990";
 	compatible = "renesas,ebisu", "renesas,r8a77990";
-
-	aliases {
-		serial0 = &scif2;
-		ethernet0 = &avb;
-		mmc0 = &sdhi3;
-		mmc1 = &sdhi0;
-		mmc2 = &sdhi1;
-	};
-
-	chosen {
-		bootargs = "ignore_loglevel rw root=/dev/nfs ip=on";
-		stdout-path = "serial0:115200n8";
-	};
-
-	audio_clkout: audio-clkout {
-		/*
-		 * This is same as <&rcar_sound 0>
-		 * but needed to avoid cs2000/rcar_sound probe dead-lock
-		 */
-		compatible = "fixed-clock";
-		#clock-cells = <0>;
-		clock-frequency = <11289600>;
-	};
-
-	backlight: backlight {
-		compatible = "pwm-backlight";
-		pwms = <&pwm3 0 50000>;
-
-		brightness-levels = <512 511 505 494 473 440 392 327 241 133 0>;
-		default-brightness-level = <10>;
-
-		power-supply = <&reg_12p0v>;
-	};
-
-	cvbs-in {
-		compatible = "composite-video-connector";
-		label = "CVBS IN";
-
-		port {
-			cvbs_con: endpoint {
-				remote-endpoint = <&adv7482_ain7>;
-			};
-		};
-	};
-
-	hdmi-in {
-		compatible = "hdmi-connector";
-		label = "HDMI IN";
-		type = "a";
-
-		port {
-			hdmi_in_con: endpoint {
-				remote-endpoint = <&adv7482_hdmi>;
-			};
-		};
-	};
-
-	hdmi-out {
-		compatible = "hdmi-connector";
-		type = "a";
-
-		port {
-			hdmi_con_out: endpoint {
-				remote-endpoint = <&adv7511_out>;
-			};
-		};
-	};
-
-	keys {
-		compatible = "gpio-keys";
-
-		pinctrl-0 = <&keys_pins>;
-		pinctrl-names = "default";
-
-		key-1 {
-			gpios = <&gpio5 10 GPIO_ACTIVE_LOW>;
-			linux,code = <KEY_1>;
-			label = "SW4-1";
-			wakeup-source;
-			debounce-interval = <20>;
-		};
-		key-2 {
-			gpios = <&gpio5 11 GPIO_ACTIVE_LOW>;
-			linux,code = <KEY_2>;
-			label = "SW4-2";
-			wakeup-source;
-			debounce-interval = <20>;
-		};
-		key-3 {
-			gpios = <&gpio5 12 GPIO_ACTIVE_LOW>;
-			linux,code = <KEY_3>;
-			label = "SW4-3";
-			wakeup-source;
-			debounce-interval = <20>;
-		};
-		key-4 {
-			gpios = <&gpio5 13 GPIO_ACTIVE_LOW>;
-			linux,code = <KEY_4>;
-			label = "SW4-4";
-			wakeup-source;
-			debounce-interval = <20>;
-		};
-	};
-
-	lvds-decoder {
-		compatible = "thine,thc63lvd1024";
-		vcc-supply = <&reg_3p3v>;
-
-		ports {
-			#address-cells = <1>;
-			#size-cells = <0>;
-
-			port@0 {
-				reg = <0>;
-				thc63lvd1024_in: endpoint {
-					remote-endpoint = <&lvds0_out>;
-				};
-			};
-
-			port@2 {
-				reg = <2>;
-				thc63lvd1024_out: endpoint {
-					remote-endpoint = <&adv7511_in>;
-				};
-			};
-		};
-	};
-
-	memory@48000000 {
-		device_type = "memory";
-		/* first 128MB is reserved for secure area. */
-		reg = <0x0 0x48000000 0x0 0x38000000>;
-	};
-
-	reg_1p8v: regulator0 {
-		compatible = "regulator-fixed";
-		regulator-name = "fixed-1.8V";
-		regulator-min-microvolt = <1800000>;
-		regulator-max-microvolt = <1800000>;
-		regulator-boot-on;
-		regulator-always-on;
-	};
-
-	reg_3p3v: regulator1 {
-		compatible = "regulator-fixed";
-		regulator-name = "fixed-3.3V";
-		regulator-min-microvolt = <3300000>;
-		regulator-max-microvolt = <3300000>;
-		regulator-boot-on;
-		regulator-always-on;
-	};
-
-	reg_12p0v: regulator2 {
-		compatible = "regulator-fixed";
-		regulator-name = "D12.0V";
-		regulator-min-microvolt = <12000000>;
-		regulator-max-microvolt = <12000000>;
-		regulator-boot-on;
-		regulator-always-on;
-	};
-
-	rsnd_ak4613: sound {
-		compatible = "simple-audio-card";
-
-		simple-audio-card,name = "rsnd-ak4613";
-		simple-audio-card,format = "left_j";
-		simple-audio-card,bitclock-master = <&sndcpu>;
-		simple-audio-card,frame-master = <&sndcpu>;
-
-		sndcodec: simple-audio-card,codec {
-			sound-dai = <&ak4613>;
-		};
-
-		sndcpu: simple-audio-card,cpu {
-			sound-dai = <&rcar_sound>;
-		};
-	};
-
-	vbus0_usb2: regulator-vbus0-usb2 {
-		compatible = "regulator-fixed";
-
-		regulator-name = "USB20_VBUS_CN";
-		regulator-min-microvolt = <5000000>;
-		regulator-max-microvolt = <5000000>;
-
-		gpio = <&gpio6 4 GPIO_ACTIVE_HIGH>;
-		enable-active-high;
-	};
-
-	vcc_sdhi0: regulator-vcc-sdhi0 {
-		compatible = "regulator-fixed";
-
-		regulator-name = "SDHI0 Vcc";
-		regulator-min-microvolt = <3300000>;
-		regulator-max-microvolt = <3300000>;
-
-		gpio = <&gpio5 17 GPIO_ACTIVE_HIGH>;
-		enable-active-high;
-	};
-
-	vccq_sdhi0: regulator-vccq-sdhi0 {
-		compatible = "regulator-gpio";
-
-		regulator-name = "SDHI0 VccQ";
-		regulator-min-microvolt = <1800000>;
-		regulator-max-microvolt = <3300000>;
-
-		gpios = <&gpio5 18 GPIO_ACTIVE_HIGH>;
-		gpios-states = <1>;
-		states = <3300000 1>, <1800000 0>;
-	};
-
-	vcc_sdhi1: regulator-vcc-sdhi1 {
-		compatible = "regulator-fixed";
-
-		regulator-name = "SDHI1 Vcc";
-		regulator-min-microvolt = <3300000>;
-		regulator-max-microvolt = <3300000>;
-
-		gpio = <&gpio0 4 GPIO_ACTIVE_HIGH>;
-		enable-active-high;
-	};
-
-	vccq_sdhi1: regulator-vccq-sdhi1 {
-		compatible = "regulator-gpio";
-
-		regulator-name = "SDHI1 VccQ";
-		regulator-min-microvolt = <1800000>;
-		regulator-max-microvolt = <3300000>;
-
-		gpios = <&gpio3 15 GPIO_ACTIVE_HIGH>;
-		gpios-states = <1>;
-		states = <3300000 1>, <1800000 0>;
-	};
-
-	vga {
-		compatible = "vga-connector";
-
-		port {
-			vga_in: endpoint {
-				remote-endpoint = <&adv7123_out>;
-			};
-		};
-	};
-
-	vga-encoder {
-		compatible = "adi,adv7123";
-
-		ports {
-			#address-cells = <1>;
-			#size-cells = <0>;
-
-			port@0 {
-				reg = <0>;
-				adv7123_in: endpoint {
-					remote-endpoint = <&du_out_rgb>;
-				};
-			};
-			port@1 {
-				reg = <1>;
-				adv7123_out: endpoint {
-					remote-endpoint = <&vga_in>;
-				};
-			};
-		};
-	};
-
-	x12_clk: x12 {
-		compatible = "fixed-clock";
-		#clock-cells = <0>;
-		clock-frequency = <24576000>;
-	};
-
-	x13_clk: x13 {
-		compatible = "fixed-clock";
-		#clock-cells = <0>;
-		clock-frequency = <74250000>;
-	};
-};
-
-&audio_clk_a {
-	clock-frequency = <22579200>;
-};
-
-&avb {
-	pinctrl-0 = <&avb_pins>;
-	pinctrl-names = "default";
-	phy-handle = <&phy0>;
-	status = "okay";
-
-	phy0: ethernet-phy@0 {
-		rxc-skew-ps = <1500>;
-		reg = <0>;
-		interrupt-parent = <&gpio2>;
-		interrupts = <21 IRQ_TYPE_LEVEL_LOW>;
-		reset-gpios = <&gpio1 20 GPIO_ACTIVE_LOW>;
-		/*
-		 * TX clock internal delay mode is required for reliable
-		 * 1Gbps communication using the KSZ9031RNX phy present on
-		 * the Ebisu board, however, TX clock internal delay mode
-		 * isn't supported on r8a77990.  Thus, limit speed to
-		 * 100Mbps for reliable communication.
-		 */
-		max-speed = <100>;
-	};
-};
-
-&canfd {
-	pinctrl-0 = <&canfd0_pins>;
-	pinctrl-names = "default";
-	status = "okay";
-
-	channel0 {
-		status = "okay";
-	};
-};
-
-&csi40 {
-	status = "okay";
-
-	ports {
-		port@0 {
-			csi40_in: endpoint {
-				clock-lanes = <0>;
-				data-lanes = <1 2>;
-				remote-endpoint = <&adv7482_txa>;
-			};
-		};
-	};
-};
-
-&du {
-	pinctrl-0 = <&du_pins>;
-	pinctrl-names = "default";
-	status = "okay";
-
-	clocks = <&cpg CPG_MOD 724>,
-		 <&cpg CPG_MOD 723>,
-		 <&x13_clk>;
-	clock-names = "du.0", "du.1", "dclkin.0";
-
-	ports {
-		port@0 {
-			endpoint {
-				remote-endpoint = <&adv7123_in>;
-			};
-		};
-	};
-};
-
-&ehci0 {
-	dr_mode = "otg";
-	status = "okay";
-};
-
-&extal_clk {
-	clock-frequency = <48000000>;
-};
-
-&hsusb {
-	dr_mode = "otg";
-	status = "okay";
-};
-
-&i2c0 {
-	status = "okay";
-
-	io_expander: gpio@20 {
-		compatible = "onnn,pca9654";
-		reg = <0x20>;
-		gpio-controller;
-		#gpio-cells = <2>;
-		interrupt-parent = <&gpio2>;
-		interrupts = <22 IRQ_TYPE_LEVEL_LOW>;
-	};
-
-	hdmi-encoder@39 {
-		compatible = "adi,adv7511w";
-		reg = <0x39>;
-		interrupt-parent = <&gpio1>;
-		interrupts = <1 IRQ_TYPE_LEVEL_LOW>;
-
-		adi,input-depth = <8>;
-		adi,input-colorspace = "rgb";
-		adi,input-clock = "1x";
-
-		ports {
-			#address-cells = <1>;
-			#size-cells = <0>;
-
-			port@0 {
-				reg = <0>;
-				adv7511_in: endpoint {
-					remote-endpoint = <&thc63lvd1024_out>;
-				};
-			};
-
-			port@1 {
-				reg = <1>;
-				adv7511_out: endpoint {
-					remote-endpoint = <&hdmi_con_out>;
-				};
-			};
-		};
-	};
-
-	video-receiver@70 {
-		compatible = "adi,adv7482";
-		reg = <0x70>;
-
-		#address-cells = <1>;
-		#size-cells = <0>;
-
-		interrupt-parent = <&gpio0>;
-		interrupt-names = "intrq1", "intrq2";
-		interrupts = <7 IRQ_TYPE_LEVEL_LOW>,
-			     <17 IRQ_TYPE_LEVEL_LOW>;
-
-		port@7 {
-			reg = <7>;
-
-			adv7482_ain7: endpoint {
-				remote-endpoint = <&cvbs_con>;
-			};
-		};
-
-		port@8 {
-			reg = <8>;
-
-			adv7482_hdmi: endpoint {
-				remote-endpoint = <&hdmi_in_con>;
-			};
-		};
-
-		port@a {
-			reg = <10>;
-
-			adv7482_txa: endpoint {
-				clock-lanes = <0>;
-				data-lanes = <1 2>;
-				remote-endpoint = <&csi40_in>;
-			};
-		};
-	};
-};
-
-&i2c3 {
-	status = "okay";
-
-	ak4613: codec@10 {
-		compatible = "asahi-kasei,ak4613";
-		#sound-dai-cells = <0>;
-		reg = <0x10>;
-		clocks = <&rcar_sound 3>;
-
-		asahi-kasei,in1-single-end;
-		asahi-kasei,in2-single-end;
-		asahi-kasei,out1-single-end;
-		asahi-kasei,out2-single-end;
-		asahi-kasei,out3-single-end;
-		asahi-kasei,out4-single-end;
-		asahi-kasei,out5-single-end;
-		asahi-kasei,out6-single-end;
-	};
-
-	cs2000: clk-multiplier@4f {
-		#clock-cells = <0>;
-		compatible = "cirrus,cs2000-cp";
-		reg = <0x4f>;
-		clocks = <&audio_clkout>, <&x12_clk>;
-		clock-names = "clk_in", "ref_clk";
-
-		assigned-clocks = <&cs2000>;
-		assigned-clock-rates = <24576000>; /* 1/1 divide */
-	};
-};
-
-&i2c_dvfs {
-	status = "okay";
-
-	clock-frequency = <400000>;
-
-	pmic: pmic@30 {
-		pinctrl-0 = <&irq0_pins>;
-		pinctrl-names = "default";
-
-		compatible = "rohm,bd9571mwv";
-		reg = <0x30>;
-		interrupt-parent = <&intc_ex>;
-		interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
-		interrupt-controller;
-		#interrupt-cells = <2>;
-		gpio-controller;
-		#gpio-cells = <2>;
-		rohm,ddr-backup-power = <0x1>;
-		rohm,rstbmode-level;
-	};
-
-	eeprom@50 {
-		compatible = "rohm,br24t01", "atmel,24c01";
-		reg = <0x50>;
-		pagesize = <8>;
-	};
-};
-
-&lvds0 {
-	status = "okay";
-
-	clocks = <&cpg CPG_MOD 727>,
-		 <&x13_clk>,
-		 <&extal_clk>;
-	clock-names = "fck", "dclkin.0", "extal";
-
-	ports {
-		port@1 {
-			lvds0_out: endpoint {
-				remote-endpoint = <&thc63lvd1024_in>;
-			};
-		};
-	};
-};
-
-&lvds1 {
-	/*
-	 * Even though the LVDS1 output is not connected, the encoder must be
-	 * enabled to supply a pixel clock to the DU for the DPAD output when
-	 * LVDS0 is in use.
-	 */
-	status = "okay";
-
-	clocks = <&cpg CPG_MOD 727>,
-		 <&x13_clk>,
-		 <&extal_clk>;
-	clock-names = "fck", "dclkin.0", "extal";
-};
-
-&ohci0 {
-	dr_mode = "otg";
-	status = "okay";
-};
-
-&pcie_bus_clk {
-	clock-frequency = <100000000>;
-};
-
-&pciec0 {
-	status = "okay";
-};
-
-&pfc {
-	avb_pins: avb {
-		groups = "avb_link", "avb_mii";
-		function = "avb";
-	};
-
-	canfd0_pins: canfd0 {
-		groups = "canfd0_data";
-		function = "canfd0";
-	};
-
-	du_pins: du {
-		groups = "du_rgb888", "du_sync", "du_disp", "du_clk_out_0";
-		function = "du";
-	};
-
-	irq0_pins: irq0 {
-		groups = "intc_ex_irq0";
-		function = "intc_ex";
-	};
-
-	keys_pins: keys {
-		pins = "GP_5_10", "GP_5_11", "GP_5_12", "GP_5_13";
-		bias-pull-up;
-	};
-
-	pwm3_pins: pwm3 {
-		groups = "pwm3_b";
-		function = "pwm3";
-	};
-
-	pwm5_pins: pwm5 {
-		groups = "pwm5_a";
-		function = "pwm5";
-	};
-
-	scif2_pins: scif2 {
-		groups = "scif2_data_a";
-		function = "scif2";
-	};
-
-	sdhi0_pins: sd0 {
-		groups = "sdhi0_data4", "sdhi0_ctrl";
-		function = "sdhi0";
-		power-source = <3300>;
-	};
-
-	sdhi0_pins_uhs: sd0_uhs {
-		groups = "sdhi0_data4", "sdhi0_ctrl";
-		function = "sdhi0";
-		power-source = <1800>;
-	};
-
-	sdhi1_pins: sd1 {
-		groups = "sdhi1_data4", "sdhi1_ctrl";
-		function = "sdhi1";
-		power-source = <3300>;
-	};
-
-	sdhi1_pins_uhs: sd1_uhs {
-		groups = "sdhi1_data4", "sdhi1_ctrl";
-		function = "sdhi1";
-		power-source = <1800>;
-	};
-
-	sdhi3_pins: sd3 {
-		groups = "sdhi3_data8", "sdhi3_ctrl", "sdhi3_ds";
-		function = "sdhi3";
-		power-source = <1800>;
-	};
-
-	sound_clk_pins: sound_clk {
-		groups = "audio_clk_a", "audio_clk_b_a", "audio_clk_c_a",
-			 "audio_clkout_a", "audio_clkout1_a";
-		function = "audio_clk";
-	};
-
-	sound_pins: sound {
-		groups = "ssi01239_ctrl", "ssi0_data", "ssi1_data";
-		function = "ssi";
-	};
-
-	usb0_pins: usb {
-		groups = "usb0_b", "usb0_id";
-		function = "usb0";
-	};
-
-	usb30_pins: usb30 {
-		groups = "usb30";
-		function = "usb30";
-	};
-};
-
-&pwm3 {
-	pinctrl-0 = <&pwm3_pins>;
-	pinctrl-names = "default";
-
-	status = "okay";
-};
-
-&pwm5 {
-	pinctrl-0 = <&pwm5_pins>;
-	pinctrl-names = "default";
-
-	status = "okay";
-};
-
-&rcar_sound {
-	pinctrl-0 = <&sound_pins>, <&sound_clk_pins>;
-	pinctrl-names = "default";
-
-	/* Single DAI */
-	#sound-dai-cells = <0>;
-
-	/* audio_clkout0/1/2/3 */
-	#clock-cells = <1>;
-	clock-frequency = <12288000 11289600>;
-
-	status = "okay";
-
-	/* update <audio_clk_b> to <cs2000> */
-	clocks = <&cpg CPG_MOD 1005>,
-		 <&cpg CPG_MOD 1006>, <&cpg CPG_MOD 1007>,
-		 <&cpg CPG_MOD 1008>, <&cpg CPG_MOD 1009>,
-		 <&cpg CPG_MOD 1010>, <&cpg CPG_MOD 1011>,
-		 <&cpg CPG_MOD 1012>, <&cpg CPG_MOD 1013>,
-		 <&cpg CPG_MOD 1014>, <&cpg CPG_MOD 1015>,
-		 <&cpg CPG_MOD 1022>, <&cpg CPG_MOD 1023>,
-		 <&cpg CPG_MOD 1024>, <&cpg CPG_MOD 1025>,
-		 <&cpg CPG_MOD 1026>, <&cpg CPG_MOD 1027>,
-		 <&cpg CPG_MOD 1028>, <&cpg CPG_MOD 1029>,
-		 <&cpg CPG_MOD 1030>, <&cpg CPG_MOD 1031>,
-		 <&cpg CPG_MOD 1020>, <&cpg CPG_MOD 1021>,
-		 <&cpg CPG_MOD 1020>, <&cpg CPG_MOD 1021>,
-		 <&cpg CPG_MOD 1019>, <&cpg CPG_MOD 1018>,
-		 <&audio_clk_a>, <&cs2000>, <&audio_clk_c>,
-		 <&cpg CPG_CORE R8A77990_CLK_ZA2>;
-
-	rcar_sound,dai {
-		dai0 {
-			playback = <&ssi0>, <&src0>, <&dvc0>;
-			capture  = <&ssi1>, <&src1>, <&dvc1>;
-		};
-	};
-
-};
-
-&rwdt {
-	timeout-sec = <60>;
-	status = "okay";
-};
-
-&scif2 {
-	pinctrl-0 = <&scif2_pins>;
-	pinctrl-names = "default";
-
-	status = "okay";
-};
-
-&sdhi0 {
-	pinctrl-0 = <&sdhi0_pins>;
-	pinctrl-1 = <&sdhi0_pins_uhs>;
-	pinctrl-names = "default", "state_uhs";
-
-	vmmc-supply = <&vcc_sdhi0>;
-	vqmmc-supply = <&vccq_sdhi0>;
-	cd-gpios = <&gpio3 12 GPIO_ACTIVE_LOW>;
-	wp-gpios = <&gpio3 13 GPIO_ACTIVE_HIGH>;
-	bus-width = <4>;
-	sd-uhs-sdr50;
-	sd-uhs-sdr104;
-	status = "okay";
-};
-
-&sdhi1 {
-	pinctrl-0 = <&sdhi1_pins>;
-	pinctrl-1 = <&sdhi1_pins_uhs>;
-	pinctrl-names = "default", "state_uhs";
-
-	vmmc-supply = <&vcc_sdhi1>;
-	vqmmc-supply = <&vccq_sdhi1>;
-	cd-gpios = <&gpio3 14 GPIO_ACTIVE_LOW>;
-	bus-width = <4>;
-	sd-uhs-sdr50;
-	sd-uhs-sdr104;
-	status = "okay";
-};
-
-&sdhi3 {
-	/* used for on-board 8bit eMMC */
-	pinctrl-0 = <&sdhi3_pins>;
-	pinctrl-1 = <&sdhi3_pins>;
-	pinctrl-names = "default", "state_uhs";
-
-	vmmc-supply = <&reg_3p3v>;
-	vqmmc-supply = <&reg_1p8v>;
-	mmc-hs200-1_8v;
-	mmc-hs400-1_8v;
-	bus-width = <8>;
-	no-sd;
-	no-sdio;
-	non-removable;
-	full-pwr-cycle-in-suspend;
-	status = "okay";
-};
-
-&ssi1 {
-	shared-pin;
-};
-
-&usb2_phy0 {
-	pinctrl-0 = <&usb0_pins>;
-	pinctrl-names = "default";
-
-	vbus-supply = <&vbus0_usb2>;
-	status = "okay";
-};
-
-&usb3_peri0 {
-	companion = <&xhci0>;
-	status = "okay";
-};
-
-&vin4 {
-	status = "okay";
-};
-
-&vin5 {
-	status = "okay";
-};
-
-&xhci0 {
-	pinctrl-0 = <&usb30_pins>;
-	pinctrl-names = "default";
-
-	status = "okay";
 };
diff --git a/arch/arm64/boot/dts/renesas/r8a77995-draak.dts b/arch/arm64/boot/dts/renesas/r8a77995-draak.dts
index 1ac15aa05b82..384825617fcf 100644
--- a/arch/arm64/boot/dts/renesas/r8a77995-draak.dts
+++ b/arch/arm64/boot/dts/renesas/r8a77995-draak.dts
@@ -8,678 +8,9 @@
 
 /dts-v1/;
 #include "r8a77995.dtsi"
-#include <dt-bindings/gpio/gpio.h>
-#include <dt-bindings/input/input.h>
+#include "draak.dtsi"
 
 / {
 	model = "Renesas Draak board based on r8a77995";
 	compatible = "renesas,draak", "renesas,r8a77995";
-
-	aliases {
-		serial0 = &scif2;
-		ethernet0 = &avb;
-	};
-
-	audio_clkout: audio-clkout {
-		/*
-		 * This is same as <&rcar_sound 0>
-		 * but needed to avoid cs2000/rcar_sound probe dead-lock
-		 */
-		compatible = "fixed-clock";
-		#clock-cells = <0>;
-		clock-frequency = <12288000>;
-	};
-
-	backlight: backlight {
-		compatible = "pwm-backlight";
-		pwms = <&pwm1 0 50000>;
-
-		brightness-levels = <512 511 505 494 473 440 392 327 241 133 0>;
-		default-brightness-level = <10>;
-
-		power-supply = <&reg_12p0v>;
-		enable-gpios = <&gpio4 0 GPIO_ACTIVE_HIGH>;
-	};
-
-	chosen {
-		bootargs = "ignore_loglevel rw root=/dev/nfs ip=on";
-		stdout-path = "serial0:115200n8";
-	};
-
-	composite-in {
-		compatible = "composite-video-connector";
-
-		port {
-			composite_con_in: endpoint {
-				remote-endpoint = <&adv7180_in>;
-			};
-		};
-	};
-
-	hdmi-in {
-		compatible = "hdmi-connector";
-		type = "a";
-
-		port {
-			hdmi_con_in: endpoint {
-				remote-endpoint = <&adv7612_in>;
-			};
-		};
-	};
-
-	hdmi-out {
-		compatible = "hdmi-connector";
-		type = "a";
-
-		port {
-			hdmi_con_out: endpoint {
-				remote-endpoint = <&adv7511_out>;
-			};
-		};
-	};
-
-	keys {
-		compatible = "gpio-keys";
-
-		pinctrl-0 = <&keys_pins>;
-		pinctrl-names = "default";
-
-		key-1 {
-			gpios = <&gpio4 12 GPIO_ACTIVE_LOW>;
-			linux,code = <KEY_1>;
-			label = "SW56-1";
-			wakeup-source;
-			debounce-interval = <20>;
-		};
-		key-2 {
-			gpios = <&gpio4 13 GPIO_ACTIVE_LOW>;
-			linux,code = <KEY_2>;
-			label = "SW56-2";
-			wakeup-source;
-			debounce-interval = <20>;
-		};
-		key-3 {
-			gpios = <&gpio4 14 GPIO_ACTIVE_LOW>;
-			linux,code = <KEY_3>;
-			label = "SW56-3";
-			wakeup-source;
-			debounce-interval = <20>;
-		};
-		key-4 {
-			gpios = <&gpio4 15 GPIO_ACTIVE_LOW>;
-			linux,code = <KEY_4>;
-			label = "SW56-4";
-			wakeup-source;
-			debounce-interval = <20>;
-		};
-	};
-
-	lvds-decoder {
-		compatible = "thine,thc63lvd1024";
-		vcc-supply = <&reg_3p3v>;
-
-		ports {
-			#address-cells = <1>;
-			#size-cells = <0>;
-
-			port@0 {
-				reg = <0>;
-				thc63lvd1024_in: endpoint {
-					remote-endpoint = <&lvds0_out>;
-				};
-			};
-
-			port@2 {
-				reg = <2>;
-				thc63lvd1024_out: endpoint {
-					remote-endpoint = <&adv7511_in>;
-				};
-			};
-		};
-	};
-
-	memory@48000000 {
-		device_type = "memory";
-		/* first 128MB is reserved for secure area. */
-		reg = <0x0 0x48000000 0x0 0x18000000>;
-	};
-
-	reg_1p8v: regulator-1p8v {
-		compatible = "regulator-fixed";
-		regulator-name = "fixed-1.8V";
-		regulator-min-microvolt = <1800000>;
-		regulator-max-microvolt = <1800000>;
-		regulator-boot-on;
-		regulator-always-on;
-	};
-
-	reg_3p3v: regulator-3p3v {
-		compatible = "regulator-fixed";
-		regulator-name = "fixed-3.3V";
-		regulator-min-microvolt = <3300000>;
-		regulator-max-microvolt = <3300000>;
-		regulator-boot-on;
-		regulator-always-on;
-	};
-
-	reg_12p0v: regulator-12p0v {
-		compatible = "regulator-fixed";
-		regulator-name = "D12.0V";
-		regulator-min-microvolt = <12000000>;
-		regulator-max-microvolt = <12000000>;
-		regulator-boot-on;
-		regulator-always-on;
-	};
-
-	sound_card: sound {
-		compatible = "audio-graph-card";
-
-		dais = <&rsnd_port0	/* ak4613 */
-			/* HDMI is not yet supported */
-		>;
-	};
-
-	vga {
-		compatible = "vga-connector";
-
-		port {
-			vga_in: endpoint {
-				remote-endpoint = <&adv7123_out>;
-			};
-		};
-	};
-
-	vga-encoder {
-		compatible = "adi,adv7123";
-
-		ports {
-			#address-cells = <1>;
-			#size-cells = <0>;
-
-			port@0 {
-				reg = <0>;
-				adv7123_in: endpoint {
-					remote-endpoint = <&du_out_rgb>;
-				};
-			};
-			port@1 {
-				reg = <1>;
-				adv7123_out: endpoint {
-					remote-endpoint = <&vga_in>;
-				};
-			};
-		};
-	};
-
-	x12_clk: x12 {
-		compatible = "fixed-clock";
-		#clock-cells = <0>;
-		clock-frequency = <74250000>;
-	};
-
-	x19_clk: x19 {
-		compatible = "fixed-clock";
-		#clock-cells = <0>;
-		clock-frequency = <24576000>;
-	};
-};
-
-&audio_clk_b {
-	/*
-	 * X11 is connected to VI4_FIELD/SCIF_CLK/AUDIO_CLKB,
-	 * and R-Car Sound uses AUDIO_CLKB.
-	 * Note is that schematic indicates VI4_FIELD conection only
-	 * not AUDIO_CLKB at SoC page.
-	 * And this VI4_FIELD/SCIF_CLK/AUDIO_CLKB is connected to SW60.
-	 * SW60 should be 1-2.
-	 */
-
-	clock-frequency = <22579200>;
-};
-
-&avb {
-	pinctrl-0 = <&avb0_pins>;
-	pinctrl-names = "default";
-	renesas,no-ether-link;
-	phy-handle = <&phy0>;
-	status = "okay";
-
-	phy0: ethernet-phy@0 {
-		rxc-skew-ps = <1500>;
-		reg = <0>;
-		interrupt-parent = <&gpio5>;
-		interrupts = <19 IRQ_TYPE_LEVEL_LOW>;
-		/*
-		 * TX clock internal delay mode is required for reliable
-		 * 1Gbps communication using the KSZ9031RNX phy present on
-		 * the Draak board, however, TX clock internal delay mode
-		 * isn't supported on r8a77995.  Thus, limit speed to
-		 * 100Mbps for reliable communication.
-		 */
-		max-speed = <100>;
-	};
-};
-
-&can0 {
-	pinctrl-0 = <&can0_pins>;
-	pinctrl-names = "default";
-	status = "okay";
-};
-
-&can1 {
-	pinctrl-0 = <&can1_pins>;
-	pinctrl-names = "default";
-	status = "okay";
-};
-
-&du {
-	pinctrl-0 = <&du_pins>;
-	pinctrl-names = "default";
-	status = "okay";
-
-	clocks = <&cpg CPG_MOD 724>,
-		 <&cpg CPG_MOD 723>,
-		 <&x12_clk>;
-	clock-names = "du.0", "du.1", "dclkin.0";
-
-	ports {
-		port@0 {
-			endpoint {
-				remote-endpoint = <&adv7123_in>;
-			};
-		};
-	};
-};
-
-&ehci0 {
-	dr_mode = "host";
-	status = "okay";
-};
-
-&extal_clk {
-	clock-frequency = <48000000>;
-};
-
-&hsusb {
-	dr_mode = "host";
-	status = "okay";
-};
-
-&i2c0 {
-	pinctrl-0 = <&i2c0_pins>;
-	pinctrl-names = "default";
-	status = "okay";
-
-	ak4613: codec@10 {
-		compatible = "asahi-kasei,ak4613";
-		#sound-dai-cells = <0>;
-		reg = <0x10>;
-		clocks = <&rcar_sound 0>; /* audio_clkout */
-
-		asahi-kasei,in1-single-end;
-		asahi-kasei,in2-single-end;
-		asahi-kasei,out1-single-end;
-		asahi-kasei,out2-single-end;
-		asahi-kasei,out3-single-end;
-		asahi-kasei,out4-single-end;
-		asahi-kasei,out5-single-end;
-		asahi-kasei,out6-single-end;
-
-		port {
-			ak4613_endpoint: endpoint {
-				remote-endpoint = <&rsnd_for_ak4613>;
-			};
-		};
-	};
-
-	composite-in@20 {
-		compatible = "adi,adv7180cp";
-		reg = <0x20>;
-
-		ports {
-			#address-cells = <1>;
-			#size-cells = <0>;
-
-			port@0 {
-				reg = <0>;
-				adv7180_in: endpoint {
-					remote-endpoint = <&composite_con_in>;
-				};
-			};
-
-			port@3 {
-				reg = <3>;
-
-				/*
-				 * The VIN4 video input path is shared between
-				 * CVBS and HDMI inputs through SW[49-53]
-				 * switches.
-				 *
-				 * CVBS is the default selection, link it to
-				 * VIN4 here.
-				 */
-				adv7180_out: endpoint {
-					remote-endpoint = <&vin4_in>;
-				};
-			};
-		};
-
-	};
-
-	hdmi-encoder@39 {
-		compatible = "adi,adv7511w";
-		reg = <0x39>, <0x3f>, <0x3c>, <0x38>;
-		reg-names = "main", "edid", "cec", "packet";
-		interrupt-parent = <&gpio1>;
-		interrupts = <28 IRQ_TYPE_LEVEL_LOW>;
-
-		adi,input-depth = <8>;
-		adi,input-colorspace = "rgb";
-		adi,input-clock = "1x";
-
-		ports {
-			#address-cells = <1>;
-			#size-cells = <0>;
-
-			port@0 {
-				reg = <0>;
-				adv7511_in: endpoint {
-					remote-endpoint = <&thc63lvd1024_out>;
-				};
-			};
-
-			port@1 {
-				reg = <1>;
-				adv7511_out: endpoint {
-					remote-endpoint = <&hdmi_con_out>;
-				};
-			};
-		};
-	};
-
-	hdmi-decoder@4c {
-		compatible = "adi,adv7612";
-		reg = <0x4c>;
-		default-input = <0>;
-
-		ports {
-			#address-cells = <1>;
-			#size-cells = <0>;
-
-			port@0 {
-				reg = <0>;
-
-				adv7612_in: endpoint {
-					remote-endpoint = <&hdmi_con_in>;
-				};
-			};
-
-			port@2 {
-				reg = <2>;
-
-				/*
-				 * The VIN4 video input path is shared between
-				 * CVBS and HDMI inputs through SW[49-53]
-				 * switches.
-				 *
-				 * CVBS is the default selection, leave HDMI
-				 * not connected here.
-				 */
-				adv7612_out: endpoint {
-					pclk-sample = <0>;
-					hsync-active = <0>;
-					vsync-active = <0>;
-				};
-			};
-		};
-	};
-
-	cs2000: clk-multiplier@4f {
-		#clock-cells = <0>;
-		compatible = "cirrus,cs2000-cp";
-		reg = <0x4f>;
-		clocks = <&audio_clkout>, <&x19_clk>; /* audio_clkout_1, x19 */
-		clock-names = "clk_in", "ref_clk";
-
-		assigned-clocks = <&cs2000>;
-		assigned-clock-rates = <24576000>; /* 1/1 divide */
-	};
-
-	eeprom@50 {
-		compatible = "rohm,br24t01", "atmel,24c01";
-		reg = <0x50>;
-		pagesize = <8>;
-	};
-};
-
-&i2c1 {
-	pinctrl-0 = <&i2c1_pins>;
-	pinctrl-names = "default";
-	status = "okay";
-};
-
-&lvds0 {
-	status = "okay";
-
-	clocks = <&cpg CPG_MOD 727>,
-		 <&x12_clk>,
-		 <&extal_clk>;
-	clock-names = "fck", "dclkin.0", "extal";
-
-	ports {
-		port@1 {
-			lvds0_out: endpoint {
-				remote-endpoint = <&thc63lvd1024_in>;
-			};
-		};
-	};
-};
-
-&lvds1 {
-	/*
-	 * Even though the LVDS1 output is not connected, the encoder must be
-	 * enabled to supply a pixel clock to the DU for the DPAD output when
-	 * LVDS0 is in use.
-	 */
-	status = "okay";
-
-	clocks = <&cpg CPG_MOD 727>,
-		 <&x12_clk>,
-		 <&extal_clk>;
-	clock-names = "fck", "dclkin.0", "extal";
-};
-
-&ohci0 {
-	dr_mode = "host";
-	status = "okay";
-};
-
-&pfc {
-	avb0_pins: avb {
-		groups = "avb0_link", "avb0_mdio", "avb0_mii";
-		function = "avb0";
-	};
-
-	can0_pins: can0 {
-		groups = "can0_data_a";
-		function = "can0";
-	};
-
-	can1_pins: can1 {
-		groups = "can1_data_a";
-		function = "can1";
-	};
-
-	du_pins: du {
-		groups = "du_rgb888", "du_sync", "du_disp", "du_clk_out_0";
-		function = "du";
-	};
-
-	i2c0_pins: i2c0 {
-		groups = "i2c0";
-		function = "i2c0";
-	};
-
-	i2c1_pins: i2c1 {
-		groups = "i2c1";
-		function = "i2c1";
-	};
-
-	keys_pins: keys {
-		pins = "GP_4_12", "GP_4_13", "GP_4_14", "GP_4_15";
-		bias-pull-up;
-	};
-
-	pwm0_pins: pwm0 {
-		groups = "pwm0_c";
-		function = "pwm0";
-	};
-
-	pwm1_pins: pwm1 {
-		groups = "pwm1_c";
-		function = "pwm1";
-	};
-
-	scif2_pins: scif2 {
-		groups = "scif2_data";
-		function = "scif2";
-	};
-
-	sdhi2_pins: sd2 {
-		groups = "mmc_data8", "mmc_ctrl";
-		function = "mmc";
-		power-source = <1800>;
-	};
-
-	sdhi2_pins_uhs: sd2_uhs {
-		groups = "mmc_data8", "mmc_ctrl";
-		function = "mmc";
-		power-source = <1800>;
-	};
-
-	sound_pins: sound {
-		groups = "ssi34_ctrl", "ssi3_data", "ssi4_data_a";
-		function = "ssi";
-	};
-
-	sound_clk_pins: sound-clk {
-		groups = "audio_clk_a", "audio_clk_b",
-			 "audio_clkout", "audio_clkout1";
-		function = "audio_clk";
-	};
-
-	usb0_pins: usb0 {
-		groups = "usb0";
-		function = "usb0";
-	};
-
-	vin4_pins_cvbs: vin4 {
-		groups = "vin4_data8", "vin4_sync", "vin4_clk";
-		function = "vin4";
-	};
-};
-
-&pwm0 {
-	pinctrl-0 = <&pwm0_pins>;
-	pinctrl-names = "default";
-
-	status = "okay";
-};
-
-&pwm1 {
-	pinctrl-0 = <&pwm1_pins>;
-	pinctrl-names = "default";
-
-	status = "okay";
-};
-
-&rcar_sound {
-	pinctrl-0 = <&sound_pins>, <&sound_clk_pins>;
-	pinctrl-names = "default";
-
-	/* Single DAI */
-	#sound-dai-cells = <0>;
-
-	/* audio_clkout0/1 */
-	#clock-cells = <1>;
-	clock-frequency = <12288000 11289600>;
-
-	status = "okay";
-
-	clocks = <&cpg CPG_MOD 1005>,
-		 <&cpg CPG_MOD 1011>, <&cpg CPG_MOD 1012>,
-		 <&cpg CPG_MOD 1025>, <&cpg CPG_MOD 1026>,
-		 <&cpg CPG_MOD 1020>, <&cpg CPG_MOD 1021>,
-		 <&cpg CPG_MOD 1020>, <&cpg CPG_MOD 1021>,
-		 <&cpg CPG_MOD 1019>, <&cpg CPG_MOD 1018>,
-		 <&cs2000>, <&audio_clk_b>,
-		 <&cpg CPG_CORE R8A77995_CLK_ZA2>;
-
-	ports {
-		rsnd_port0: port {
-			rsnd_for_ak4613: endpoint {
-				remote-endpoint = <&ak4613_endpoint>;
-				dai-format = "left_j";
-				bitclock-master = <&rsnd_for_ak4613>;
-				frame-master = <&rsnd_for_ak4613>;
-				playback = <&ssi3>, <&src5>, <&dvc0>;
-				capture  = <&ssi4>, <&src6>, <&dvc1>;
-			};
-		};
-	};
-};
-
-&rwdt {
-	timeout-sec = <60>;
-	status = "okay";
-};
-
-&scif2 {
-	pinctrl-0 = <&scif2_pins>;
-	pinctrl-names = "default";
-
-	status = "okay";
-};
-
-&sdhi2 {
-	/* used for on-board eMMC */
-	pinctrl-0 = <&sdhi2_pins>;
-	pinctrl-1 = <&sdhi2_pins_uhs>;
-	pinctrl-names = "default", "state_uhs";
-
-	vmmc-supply = <&reg_3p3v>;
-	vqmmc-supply = <&reg_1p8v>;
-	bus-width = <8>;
-	mmc-hs200-1_8v;
-	no-sd;
-	no-sdio;
-	non-removable;
-	status = "okay";
-};
-
-&ssi4 {
-	shared-pin;
-};
-
-&usb2_phy0 {
-	pinctrl-0 = <&usb0_pins>;
-	pinctrl-names = "default";
-
-	renesas,no-otg-pins;
-	status = "okay";
-};
-
-&vin4 {
-	pinctrl-0 = <&vin4_pins_cvbs>;
-	pinctrl-names = "default";
-
-	status = "okay";
-
-	ports {
-		port {
-			vin4_in: endpoint {
-				remote-endpoint = <&adv7180_out>;
-			};
-		};
-	};
 };
diff --git a/arch/arm64/boot/dts/renesas/r8a779a0-falcon-cpu.dtsi b/arch/arm64/boot/dts/renesas/r8a779a0-falcon-cpu.dtsi
index a0a1a1da0d87..cd2f0d60f21a 100644
--- a/arch/arm64/boot/dts/renesas/r8a779a0-falcon-cpu.dtsi
+++ b/arch/arm64/boot/dts/renesas/r8a779a0-falcon-cpu.dtsi
@@ -6,6 +6,7 @@
  */
 
 #include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
 #include <dt-bindings/leds/common.h>
 
 #include "r8a779a0.dtsi"
@@ -22,6 +23,37 @@
 		stdout-path = "serial0:115200n8";
 	};
 
+	keys {
+		compatible = "gpio-keys";
+
+		pinctrl-0 = <&keys_pins>;
+		pinctrl-names = "default";
+
+		key-1 {
+			gpios = <&gpio6 18 GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_1>;
+			label = "SW47";
+			wakeup-source;
+			debounce-interval = <20>;
+		};
+
+		key-2 {
+			gpios = <&gpio6 19 GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_2>;
+			label = "SW48";
+			wakeup-source;
+			debounce-interval = <20>;
+		};
+
+		key-3 {
+			gpios = <&gpio6 20 GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_3>;
+			label = "SW49";
+			wakeup-source;
+			debounce-interval = <20>;
+		};
+	};
+
 	leds {
 		compatible = "gpio-leds";
 
@@ -160,12 +192,22 @@
 		function = "i2c6";
 	};
 
+	keys_pins: keys {
+		pins = "GP_6_18", "GP_6_19", "GP_6_20";
+		bias-pull-up;
+	};
+
 	mmc_pins: mmc {
 		groups = "mmc_data8", "mmc_ctrl", "mmc_ds";
 		function = "mmc";
 		power-source = <1800>;
 	};
 
+	qspi0_pins: qspi0 {
+		groups = "qspi0_ctrl", "qspi0_data4";
+		function = "qspi0";
+	};
+
 	scif0_pins: scif0 {
 		groups = "scif0_data", "scif0_ctrl";
 		function = "scif0";
@@ -177,6 +219,34 @@
 	};
 };
 
+&rpc {
+	pinctrl-0 = <&qspi0_pins>;
+	pinctrl-names = "default";
+
+	status = "okay";
+
+	flash@0 {
+		compatible = "spansion,s25fs512s", "jedec,spi-nor";
+		reg = <0>;
+		spi-max-frequency = <40000000>;
+		spi-rx-bus-width = <4>;
+
+		partitions {
+			compatible = "fixed-partitions";
+			#address-cells = <1>;
+			#size-cells = <1>;
+
+			boot@0 {
+				reg = <0x0 0xcc0000>;
+				read-only;
+			};
+			user@cc0000 {
+				reg = <0xcc0000 0x3340000>;
+			};
+		};
+	};
+};
+
 &rwdt {
 	timeout-sec = <60>;
 	status = "okay";
diff --git a/arch/arm64/boot/dts/renesas/r8a779a0-falcon.dts b/arch/arm64/boot/dts/renesas/r8a779a0-falcon.dts
index dc671ff57ec7..e46dc9aa0a43 100644
--- a/arch/arm64/boot/dts/renesas/r8a779a0-falcon.dts
+++ b/arch/arm64/boot/dts/renesas/r8a779a0-falcon.dts
@@ -27,6 +27,8 @@
 	status = "okay";
 
 	phy0: ethernet-phy@0 {
+		compatible = "ethernet-phy-id0022.1622",
+			     "ethernet-phy-ieee802.3-c22";
 		rxc-skew-ps = <1500>;
 		reg = <0>;
 		interrupt-parent = <&gpio4>;
diff --git a/arch/arm64/boot/dts/renesas/r8a779a0.dtsi b/arch/arm64/boot/dts/renesas/r8a779a0.dtsi
index 631d520cebee..43bf2cbfbd8f 100644
--- a/arch/arm64/boot/dts/renesas/r8a779a0.dtsi
+++ b/arch/arm64/boot/dts/renesas/r8a779a0.dtsi
@@ -933,6 +933,17 @@
 			status = "disabled";
 		};
 
+		tpu: pwm@e6e80000 {
+			compatible = "renesas,tpu-r8a779a0", "renesas,tpu";
+			reg = <0 0xe6e80000 0 0x148>;
+			interrupts = <GIC_SPI 515 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&cpg CPG_MOD 718>;
+			power-domains = <&sysc R8A779A0_PD_ALWAYS_ON>;
+			resets = <&cpg 718>;
+			#pwm-cells = <3>;
+			status = "disabled";
+		};
+
 		msiof0: spi@e6e90000 {
 			compatible = "renesas,msiof-r8a779a0",
 				     "renesas,rcar-gen3-msiof";
@@ -1023,6 +1034,902 @@
 			status = "disabled";
 		};
 
+		vin00: video@e6ef0000 {
+			compatible = "renesas,vin-r8a779a0";
+			reg = <0 0xe6ef0000 0 0x1000>;
+			interrupts = <GIC_SPI 160 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&cpg CPG_MOD 730>;
+			power-domains = <&sysc R8A779A0_PD_ALWAYS_ON>;
+			resets = <&cpg 730>;
+			renesas,id = <0>;
+			status = "disabled";
+
+			ports {
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				port@2 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+
+					reg = <2>;
+
+					vin00isp0: endpoint@0 {
+						reg = <0>;
+						remote-endpoint = <&isp0vin00>;
+					};
+				};
+			};
+		};
+
+		vin01: video@e6ef1000 {
+			compatible = "renesas,vin-r8a779a0";
+			reg = <0 0xe6ef1000 0 0x1000>;
+			interrupts = <GIC_SPI 161 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&cpg CPG_MOD 731>;
+			power-domains = <&sysc R8A779A0_PD_ALWAYS_ON>;
+			resets = <&cpg 731>;
+			renesas,id = <1>;
+			status = "disabled";
+
+			ports {
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				port@2 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+
+					reg = <2>;
+
+					vin01isp0: endpoint@0 {
+						reg = <0>;
+						remote-endpoint = <&isp0vin01>;
+					};
+				};
+			};
+		};
+
+		vin02: video@e6ef2000 {
+			compatible = "renesas,vin-r8a779a0";
+			reg = <0 0xe6ef2000 0 0x1000>;
+			interrupts = <GIC_SPI 162 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&cpg CPG_MOD 800>;
+			power-domains = <&sysc R8A779A0_PD_ALWAYS_ON>;
+			resets = <&cpg 800>;
+			renesas,id = <2>;
+			status = "disabled";
+
+			ports {
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				port@2 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+
+					reg = <2>;
+
+					vin02isp0: endpoint@0 {
+						reg = <0>;
+						remote-endpoint = <&isp0vin02>;
+					};
+				};
+			};
+		};
+
+		vin03: video@e6ef3000 {
+			compatible = "renesas,vin-r8a779a0";
+			reg = <0 0xe6ef3000 0 0x1000>;
+			interrupts = <GIC_SPI 163 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&cpg CPG_MOD 801>;
+			power-domains = <&sysc R8A779A0_PD_ALWAYS_ON>;
+			resets = <&cpg 801>;
+			renesas,id = <3>;
+			status = "disabled";
+
+			ports {
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				port@2 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+
+					reg = <2>;
+
+					vin03isp0: endpoint@0 {
+						reg = <0>;
+						remote-endpoint = <&isp0vin03>;
+					};
+				};
+			};
+		};
+
+		vin04: video@e6ef4000 {
+			compatible = "renesas,vin-r8a779a0";
+			reg = <0 0xe6ef4000 0 0x1000>;
+			interrupts = <GIC_SPI 164 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&cpg CPG_MOD 802>;
+			power-domains = <&sysc R8A779A0_PD_ALWAYS_ON>;
+			resets = <&cpg 802>;
+			renesas,id = <4>;
+			status = "disabled";
+
+			ports {
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				port@2 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+
+					reg = <2>;
+
+					vin04isp0: endpoint@0 {
+						reg = <0>;
+						remote-endpoint = <&isp0vin04>;
+					};
+				};
+			};
+		};
+
+		vin05: video@e6ef5000 {
+			compatible = "renesas,vin-r8a779a0";
+			reg = <0 0xe6ef5000 0 0x1000>;
+			interrupts = <GIC_SPI 165 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&cpg CPG_MOD 803>;
+			power-domains = <&sysc R8A779A0_PD_ALWAYS_ON>;
+			resets = <&cpg 803>;
+			renesas,id = <5>;
+			status = "disabled";
+
+			ports {
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				port@2 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+
+					reg = <2>;
+
+					vin05isp0: endpoint@0 {
+						reg = <0>;
+						remote-endpoint = <&isp0vin05>;
+					};
+				};
+			};
+		};
+
+		vin06: video@e6ef6000 {
+			compatible = "renesas,vin-r8a779a0";
+			reg = <0 0xe6ef6000 0 0x1000>;
+			interrupts = <GIC_SPI 166 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&cpg CPG_MOD 804>;
+			power-domains = <&sysc R8A779A0_PD_ALWAYS_ON>;
+			resets = <&cpg 804>;
+			renesas,id = <6>;
+			status = "disabled";
+
+			ports {
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				port@2 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+
+					reg = <2>;
+
+					vin06isp0: endpoint@0 {
+						reg = <0>;
+						remote-endpoint = <&isp0vin06>;
+					};
+				};
+			};
+		};
+
+		vin07: video@e6ef7000 {
+			compatible = "renesas,vin-r8a779a0";
+			reg = <0 0xe6ef7000 0 0x1000>;
+			interrupts = <GIC_SPI 167 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&cpg CPG_MOD 805>;
+			power-domains = <&sysc R8A779A0_PD_ALWAYS_ON>;
+			resets = <&cpg 805>;
+			renesas,id = <7>;
+			status = "disabled";
+
+			ports {
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				port@2 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+
+					reg = <2>;
+
+					vin07isp0: endpoint@0 {
+						reg = <0>;
+						remote-endpoint = <&isp0vin07>;
+					};
+				};
+			};
+		};
+
+		vin08: video@e6ef8000 {
+			compatible = "renesas,vin-r8a779a0";
+			reg = <0 0xe6ef8000 0 0x1000>;
+			interrupts = <GIC_SPI 168 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&cpg CPG_MOD 806>;
+			power-domains = <&sysc R8A779A0_PD_ALWAYS_ON>;
+			resets = <&cpg 806>;
+			renesas,id = <8>;
+			status = "disabled";
+
+			ports {
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				port@2 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+
+					reg = <2>;
+
+					vin08isp1: endpoint@1 {
+						reg = <1>;
+						remote-endpoint = <&isp1vin08>;
+					};
+				};
+			};
+		};
+
+		vin09: video@e6ef9000 {
+			compatible = "renesas,vin-r8a779a0";
+			reg = <0 0xe6ef9000 0 0x1000>;
+			interrupts = <GIC_SPI 169 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&cpg CPG_MOD 807>;
+			power-domains = <&sysc R8A779A0_PD_ALWAYS_ON>;
+			resets = <&cpg 807>;
+			renesas,id = <9>;
+			status = "disabled";
+
+			ports {
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				port@2 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+
+					reg = <2>;
+
+					vin09isp1: endpoint@1 {
+						reg = <1>;
+						remote-endpoint = <&isp1vin09>;
+					};
+				};
+			};
+		};
+
+		vin10: video@e6efa000 {
+			compatible = "renesas,vin-r8a779a0";
+			reg = <0 0xe6efa000 0 0x1000>;
+			interrupts = <GIC_SPI 170 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&cpg CPG_MOD 808>;
+			power-domains = <&sysc R8A779A0_PD_ALWAYS_ON>;
+			resets = <&cpg 808>;
+			renesas,id = <10>;
+			status = "disabled";
+
+			ports {
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				port@2 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+
+					reg = <2>;
+
+					vin10isp1: endpoint@1 {
+						reg = <1>;
+						remote-endpoint = <&isp1vin10>;
+					};
+				};
+			};
+		};
+
+		vin11: video@e6efb000 {
+			compatible = "renesas,vin-r8a779a0";
+			reg = <0 0xe6efb000 0 0x1000>;
+			interrupts = <GIC_SPI 171 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&cpg CPG_MOD 809>;
+			power-domains = <&sysc R8A779A0_PD_ALWAYS_ON>;
+			resets = <&cpg 809>;
+			renesas,id = <11>;
+			status = "disabled";
+
+			ports {
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				port@2 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+
+					reg = <2>;
+
+					vin11isp1: endpoint@1 {
+						reg = <1>;
+						remote-endpoint = <&isp1vin11>;
+					};
+				};
+			};
+		};
+
+		vin12: video@e6efc000 {
+			compatible = "renesas,vin-r8a779a0";
+			reg = <0 0xe6efc000 0 0x1000>;
+			interrupts = <GIC_SPI 172 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&cpg CPG_MOD 810>;
+			power-domains = <&sysc R8A779A0_PD_ALWAYS_ON>;
+			resets = <&cpg 810>;
+			renesas,id = <12>;
+			status = "disabled";
+
+			ports {
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				port@2 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+
+					reg = <2>;
+
+					vin12isp1: endpoint@1 {
+						reg = <1>;
+						remote-endpoint = <&isp1vin12>;
+					};
+				};
+			};
+		};
+
+		vin13: video@e6efd000 {
+			compatible = "renesas,vin-r8a779a0";
+			reg = <0 0xe6efd000 0 0x1000>;
+			interrupts = <GIC_SPI 173 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&cpg CPG_MOD 811>;
+			power-domains = <&sysc R8A779A0_PD_ALWAYS_ON>;
+			resets = <&cpg 811>;
+			renesas,id = <13>;
+			status = "disabled";
+
+			ports {
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				port@2 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+
+					reg = <2>;
+
+					vin13isp1: endpoint@1 {
+						reg = <1>;
+						remote-endpoint = <&isp1vin13>;
+					};
+				};
+			};
+		};
+
+		vin14: video@e6efe000 {
+			compatible = "renesas,vin-r8a779a0";
+			reg = <0 0xe6efe000 0 0x1000>;
+			interrupts = <GIC_SPI 174 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&cpg CPG_MOD 812>;
+			power-domains = <&sysc R8A779A0_PD_ALWAYS_ON>;
+			resets = <&cpg 812>;
+			renesas,id = <14>;
+			status = "disabled";
+
+			ports {
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				port@2 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+
+					reg = <2>;
+
+					vin14isp1: endpoint@1 {
+						reg = <1>;
+						remote-endpoint = <&isp1vin14>;
+					};
+				};
+			};
+		};
+
+		vin15: video@e6eff000 {
+			compatible = "renesas,vin-r8a779a0";
+			reg = <0 0xe6eff000 0 0x1000>;
+			interrupts = <GIC_SPI 175 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&cpg CPG_MOD 813>;
+			power-domains = <&sysc R8A779A0_PD_ALWAYS_ON>;
+			resets = <&cpg 813>;
+			renesas,id = <15>;
+			status = "disabled";
+
+			ports {
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				port@2 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+
+					reg = <2>;
+
+					vin15isp1: endpoint@1 {
+						reg = <1>;
+						remote-endpoint = <&isp1vin15>;
+					};
+				};
+			};
+		};
+
+		vin16: video@e6ed0000 {
+			compatible = "renesas,vin-r8a779a0";
+			reg = <0 0xe6ed0000 0 0x1000>;
+			interrupts = <GIC_SPI 176 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&cpg CPG_MOD 814>;
+			power-domains = <&sysc R8A779A0_PD_ALWAYS_ON>;
+			resets = <&cpg 814>;
+			renesas,id = <16>;
+			status = "disabled";
+
+			ports {
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				port@2 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+
+					reg = <2>;
+
+					vin16isp2: endpoint@2 {
+						reg = <2>;
+						remote-endpoint = <&isp2vin16>;
+					};
+				};
+			};
+		};
+
+		vin17: video@e6ed1000 {
+			compatible = "renesas,vin-r8a779a0";
+			reg = <0 0xe6ed1000 0 0x1000>;
+			interrupts = <GIC_SPI 177 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&cpg CPG_MOD 815>;
+			power-domains = <&sysc R8A779A0_PD_ALWAYS_ON>;
+			resets = <&cpg 815>;
+			renesas,id = <17>;
+			status = "disabled";
+
+			ports {
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				port@2 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+
+					reg = <2>;
+
+					vin17isp2: endpoint@2 {
+						reg = <2>;
+						remote-endpoint = <&isp2vin17>;
+					};
+				};
+			};
+		};
+
+		vin18: video@e6ed2000 {
+			compatible = "renesas,vin-r8a779a0";
+			reg = <0 0xe6ed2000 0 0x1000>;
+			interrupts = <GIC_SPI 178 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&cpg CPG_MOD 816>;
+			power-domains = <&sysc R8A779A0_PD_ALWAYS_ON>;
+			resets = <&cpg 816>;
+			renesas,id = <18>;
+			status = "disabled";
+
+			ports {
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				port@2 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+
+					reg = <2>;
+
+					vin18isp2: endpoint@2 {
+						reg = <2>;
+						remote-endpoint = <&isp2vin18>;
+					};
+				};
+			};
+		};
+
+		vin19: video@e6ed3000 {
+			compatible = "renesas,vin-r8a779a0";
+			reg = <0 0xe6ed3000 0 0x1000>;
+			interrupts = <GIC_SPI 179 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&cpg CPG_MOD 817>;
+			power-domains = <&sysc R8A779A0_PD_ALWAYS_ON>;
+			resets = <&cpg 817>;
+			renesas,id = <19>;
+			status = "disabled";
+
+			ports {
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				port@2 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+
+					reg = <2>;
+
+					vin19isp2: endpoint@2 {
+						reg = <2>;
+						remote-endpoint = <&isp2vin19>;
+					};
+				};
+			};
+		};
+
+		vin20: video@e6ed4000 {
+			compatible = "renesas,vin-r8a779a0";
+			reg = <0 0xe6ed4000 0 0x1000>;
+			interrupts = <GIC_SPI 180 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&cpg CPG_MOD 818>;
+			power-domains = <&sysc R8A779A0_PD_ALWAYS_ON>;
+			resets = <&cpg 818>;
+			renesas,id = <20>;
+			status = "disabled";
+
+			ports {
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				port@2 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+
+					reg = <2>;
+
+					vin20isp2: endpoint@2 {
+						reg = <2>;
+						remote-endpoint = <&isp2vin20>;
+					};
+				};
+			};
+		};
+
+		vin21: video@e6ed5000 {
+			compatible = "renesas,vin-r8a779a0";
+			reg = <0 0xe6ed5000 0 0x1000>;
+			interrupts = <GIC_SPI 181 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&cpg CPG_MOD 819>;
+			power-domains = <&sysc R8A779A0_PD_ALWAYS_ON>;
+			resets = <&cpg 819>;
+			renesas,id = <21>;
+			status = "disabled";
+
+			ports {
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				port@2 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+
+					reg = <2>;
+
+					vin21isp2: endpoint@2 {
+						reg = <2>;
+						remote-endpoint = <&isp2vin21>;
+					};
+				};
+			};
+		};
+
+		vin22: video@e6ed6000 {
+			compatible = "renesas,vin-r8a779a0";
+			reg = <0 0xe6ed6000 0 0x1000>;
+			interrupts = <GIC_SPI 182 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&cpg CPG_MOD 820>;
+			power-domains = <&sysc R8A779A0_PD_ALWAYS_ON>;
+			resets = <&cpg 820>;
+			renesas,id = <22>;
+			status = "disabled";
+
+			ports {
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				port@2 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+
+					reg = <2>;
+
+					vin22isp2: endpoint@2 {
+						reg = <2>;
+						remote-endpoint = <&isp2vin22>;
+					};
+				};
+			};
+		};
+
+		vin23: video@e6ed7000 {
+			compatible = "renesas,vin-r8a779a0";
+			reg = <0 0xe6ed7000 0 0x1000>;
+			interrupts = <GIC_SPI 183 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&cpg CPG_MOD 821>;
+			power-domains = <&sysc R8A779A0_PD_ALWAYS_ON>;
+			resets = <&cpg 821>;
+			renesas,id = <23>;
+			status = "disabled";
+
+			ports {
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				port@2 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+
+					reg = <2>;
+
+					vin23isp2: endpoint@2 {
+						reg = <2>;
+						remote-endpoint = <&isp2vin23>;
+					};
+				};
+			};
+		};
+
+		vin24: video@e6ed8000 {
+			compatible = "renesas,vin-r8a779a0";
+			reg = <0 0xe6ed8000 0 0x1000>;
+			interrupts = <GIC_SPI 184 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&cpg CPG_MOD 822>;
+			power-domains = <&sysc R8A779A0_PD_ALWAYS_ON>;
+			resets = <&cpg 822>;
+			renesas,id = <24>;
+			status = "disabled";
+
+			ports {
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				port@2 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+
+					reg = <2>;
+
+					vin24isp3: endpoint@3 {
+						reg = <3>;
+						remote-endpoint = <&isp3vin24>;
+					};
+				};
+			};
+		};
+
+		vin25: video@e6ed9000 {
+			compatible = "renesas,vin-r8a779a0";
+			reg = <0 0xe6ed9000 0 0x1000>;
+			interrupts = <GIC_SPI 185 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&cpg CPG_MOD 823>;
+			power-domains = <&sysc R8A779A0_PD_ALWAYS_ON>;
+			resets = <&cpg 823>;
+			renesas,id = <25>;
+			status = "disabled";
+
+			ports {
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				port@2 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+
+					reg = <2>;
+
+					vin25isp3: endpoint@3 {
+						reg = <3>;
+						remote-endpoint = <&isp3vin25>;
+					};
+				};
+			};
+		};
+
+		vin26: video@e6eda000 {
+			compatible = "renesas,vin-r8a779a0";
+			reg = <0 0xe6eda000 0 0x1000>;
+			interrupts = <GIC_SPI 186 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&cpg CPG_MOD 824>;
+			power-domains = <&sysc R8A779A0_PD_ALWAYS_ON>;
+			resets = <&cpg 824>;
+			renesas,id = <26>;
+			status = "disabled";
+
+			ports {
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				port@2 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+
+					reg = <2>;
+
+					vin26isp3: endpoint@3 {
+						reg = <3>;
+						remote-endpoint = <&isp3vin26>;
+					};
+				};
+			};
+		};
+
+		vin27: video@e6edb000 {
+			compatible = "renesas,vin-r8a779a0";
+			reg = <0 0xe6edb000 0 0x1000>;
+			interrupts = <GIC_SPI 187 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&cpg CPG_MOD 825>;
+			power-domains = <&sysc R8A779A0_PD_ALWAYS_ON>;
+			resets = <&cpg 825>;
+			renesas,id = <27>;
+			status = "disabled";
+
+			ports {
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				port@2 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+
+					reg = <2>;
+
+					vin27isp3: endpoint@3 {
+						reg = <3>;
+						remote-endpoint = <&isp3vin27>;
+					};
+				};
+			};
+		};
+
+		vin28: video@e6edc000 {
+			compatible = "renesas,vin-r8a779a0";
+			reg = <0 0xe6edc000 0 0x1000>;
+			interrupts = <GIC_SPI 188 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&cpg CPG_MOD 826>;
+			power-domains = <&sysc R8A779A0_PD_ALWAYS_ON>;
+			resets = <&cpg 826>;
+			renesas,id = <28>;
+			status = "disabled";
+
+			ports {
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				port@2 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+
+					reg = <2>;
+
+					vin28isp3: endpoint@3 {
+						reg = <3>;
+						remote-endpoint = <&isp3vin28>;
+					};
+				};
+			};
+		};
+
+		vin29: video@e6edd000 {
+			compatible = "renesas,vin-r8a779a0";
+			reg = <0 0xe6edd000 0 0x1000>;
+			interrupts = <GIC_SPI 189 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&cpg CPG_MOD 827>;
+			power-domains = <&sysc R8A779A0_PD_ALWAYS_ON>;
+			resets = <&cpg 827>;
+			renesas,id = <29>;
+			status = "disabled";
+
+			ports {
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				port@2 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+
+					reg = <2>;
+
+					vin29isp3: endpoint@3 {
+						reg = <3>;
+						remote-endpoint = <&isp3vin29>;
+					};
+				};
+			};
+		};
+
+		vin30: video@e6ede000 {
+			compatible = "renesas,vin-r8a779a0";
+			reg = <0 0xe6ede000 0 0x1000>;
+			interrupts = <GIC_SPI 190 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&cpg CPG_MOD 828>;
+			power-domains = <&sysc R8A779A0_PD_ALWAYS_ON>;
+			resets = <&cpg 828>;
+			renesas,id = <30>;
+			status = "disabled";
+
+			ports {
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				port@2 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+
+					reg = <2>;
+
+					vin30isp3: endpoint@3 {
+						reg = <3>;
+						remote-endpoint = <&isp3vin30>;
+					};
+				};
+			};
+		};
+
+		vin31: video@e6edf000 {
+			compatible = "renesas,vin-r8a779a0";
+			reg = <0 0xe6edf000 0 0x1000>;
+			interrupts = <GIC_SPI 191 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&cpg CPG_MOD 829>;
+			power-domains = <&sysc R8A779A0_PD_ALWAYS_ON>;
+			resets = <&cpg 829>;
+			renesas,id = <31>;
+			status = "disabled";
+
+			ports {
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				port@2 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+
+					reg = <2>;
+
+					vin31isp3: endpoint@3 {
+						reg = <3>;
+						remote-endpoint = <&isp3vin31>;
+					};
+				};
+			};
+		};
+
 		dmac1: dma-controller@e7350000 {
 			compatible = "renesas,dmac-r8a779a0";
 			reg = <0 0xe7350000 0 0x1000>,
@@ -1090,9 +1997,124 @@
 			power-domains = <&sysc R8A779A0_PD_ALWAYS_ON>;
 			resets = <&cpg 706>;
 			max-frequency = <200000000>;
+			iommus = <&ipmmu_ds0 32>;
 			status = "disabled";
 		};
 
+		rpc: spi@ee200000 {
+			compatible = "renesas,r8a779a0-rpc-if",
+				     "renesas,rcar-gen3-rpc-if";
+			reg = <0 0xee200000 0 0x200>,
+			      <0 0x08000000 0 0x04000000>,
+			      <0 0xee208000 0 0x100>;
+			reg-names = "regs", "dirmap", "wbuf";
+			interrupts = <GIC_SPI 135 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&cpg CPG_MOD 629>;
+			clock-names = "rpc";
+			power-domains = <&sysc R8A779A0_PD_ALWAYS_ON>;
+			resets = <&cpg 629>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			status = "disabled";
+		};
+
+		ipmmu_rt0: iommu@ee480000 {
+			compatible = "renesas,ipmmu-r8a779a0";
+			reg = <0 0xee480000 0 0x20000>;
+			renesas,ipmmu-main = <&ipmmu_mm 10>;
+			power-domains = <&sysc R8A779A0_PD_ALWAYS_ON>;
+			#iommu-cells = <1>;
+		};
+
+		ipmmu_rt1: iommu@ee4c0000 {
+			compatible = "renesas,ipmmu-r8a779a0";
+			reg = <0 0xee4c0000 0 0x20000>;
+			renesas,ipmmu-main = <&ipmmu_mm 19>;
+			power-domains = <&sysc R8A779A0_PD_ALWAYS_ON>;
+			#iommu-cells = <1>;
+		};
+
+		ipmmu_ds0: iommu@eed00000 {
+			compatible = "renesas,ipmmu-r8a779a0";
+			reg = <0 0xeed00000 0 0x20000>;
+			renesas,ipmmu-main = <&ipmmu_mm 0>;
+			power-domains = <&sysc R8A779A0_PD_ALWAYS_ON>;
+			#iommu-cells = <1>;
+		};
+
+		ipmmu_ds1: iommu@eed40000 {
+			compatible = "renesas,ipmmu-r8a779a0";
+			reg = <0 0xeed40000 0 0x20000>;
+			renesas,ipmmu-main = <&ipmmu_mm 1>;
+			power-domains = <&sysc R8A779A0_PD_ALWAYS_ON>;
+			#iommu-cells = <1>;
+		};
+
+		ipmmu_ir: iommu@eed80000 {
+			compatible = "renesas,ipmmu-r8a779a0";
+			reg = <0 0xeed80000 0 0x20000>;
+			renesas,ipmmu-main = <&ipmmu_mm 3>;
+			power-domains = <&sysc R8A779A0_PD_A3IR>;
+			#iommu-cells = <1>;
+		};
+
+		ipmmu_vc0: iommu@eedc0000 {
+			compatible = "renesas,ipmmu-r8a779a0";
+			reg = <0 0xeedc0000 0 0x20000>;
+			renesas,ipmmu-main = <&ipmmu_mm 12>;
+			power-domains = <&sysc R8A779A0_PD_ALWAYS_ON>;
+			#iommu-cells = <1>;
+		};
+
+		ipmmu_vi0: iommu@eee80000 {
+			compatible = "renesas,ipmmu-r8a779a0";
+			reg = <0 0xeee80000 0 0x20000>;
+			renesas,ipmmu-main = <&ipmmu_mm 14>;
+			power-domains = <&sysc R8A779A0_PD_ALWAYS_ON>;
+			#iommu-cells = <1>;
+		};
+
+		ipmmu_vi1: iommu@eeec0000 {
+			compatible = "renesas,ipmmu-r8a779a0";
+			reg = <0 0xeeec0000 0 0x20000>;
+			renesas,ipmmu-main = <&ipmmu_mm 15>;
+			power-domains = <&sysc R8A779A0_PD_ALWAYS_ON>;
+			#iommu-cells = <1>;
+		};
+
+		ipmmu_3dg: iommu@eee00000 {
+			compatible = "renesas,ipmmu-r8a779a0";
+			reg = <0 0xeee00000 0 0x20000>;
+			renesas,ipmmu-main = <&ipmmu_mm 6>;
+			power-domains = <&sysc R8A779A0_PD_ALWAYS_ON>;
+			#iommu-cells = <1>;
+		};
+
+		ipmmu_vip0: iommu@eef00000 {
+			compatible = "renesas,ipmmu-r8a779a0";
+			reg = <0 0xeef00000 0 0x20000>;
+			renesas,ipmmu-main = <&ipmmu_mm 5>;
+			power-domains = <&sysc R8A779A0_PD_ALWAYS_ON>;
+			#iommu-cells = <1>;
+		};
+
+		ipmmu_vip1: iommu@eef40000 {
+			compatible = "renesas,ipmmu-r8a779a0";
+			reg = <0 0xeef40000 0 0x20000>;
+			renesas,ipmmu-main = <&ipmmu_mm 11>;
+			power-domains = <&sysc R8A779A0_PD_ALWAYS_ON>;
+			#iommu-cells = <1>;
+		};
+
+		ipmmu_mm: iommu@eefc0000 {
+			compatible = "renesas,ipmmu-r8a779a0";
+			reg = <0 0xeefc0000 0 0x20000>;
+			interrupts = <GIC_SPI 21 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 22 IRQ_TYPE_LEVEL_HIGH>;
+			power-domains = <&sysc R8A779A0_PD_ALWAYS_ON>;
+			#iommu-cells = <1>;
+		};
+
 		gic: interrupt-controller@f1000000 {
 			compatible = "arm,gic-v3";
 			#interrupt-cells = <3>;
@@ -1142,6 +2164,442 @@
 			renesas,fcp = <&fcpvd1>;
 		};
 
+		csi40: csi2@feaa0000 {
+			compatible = "renesas,r8a779a0-csi2";
+			reg = <0 0xfeaa0000 0 0x10000>;
+			interrupts = <GIC_SPI 192 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&cpg CPG_MOD 331>;
+			power-domains = <&sysc R8A779A0_PD_ALWAYS_ON>;
+			resets = <&cpg 331>;
+			status = "disabled";
+
+			ports {
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				port@0 {
+					reg = <0>;
+				};
+
+				port@1 {
+					reg = <1>;
+					csi40isp0: endpoint {
+						remote-endpoint = <&isp0csi40>;
+					};
+				};
+			};
+		};
+
+		csi41: csi2@feab0000 {
+			compatible = "renesas,r8a779a0-csi2";
+			reg = <0 0xfeab0000 0 0x10000>;
+			interrupts = <GIC_SPI 193 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&cpg CPG_MOD 400>;
+			power-domains = <&sysc R8A779A0_PD_ALWAYS_ON>;
+			resets = <&cpg 400>;
+			status = "disabled";
+
+			ports {
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				port@0 {
+					reg = <0>;
+				};
+
+				port@1 {
+					reg = <1>;
+					csi41isp1: endpoint {
+						remote-endpoint = <&isp1csi41>;
+					};
+				};
+			};
+		};
+
+		csi42: csi2@fed60000 {
+			compatible = "renesas,r8a779a0-csi2";
+			reg = <0 0xfed60000 0 0x10000>;
+			interrupts = <GIC_SPI 194 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&cpg CPG_MOD 401>;
+			power-domains = <&sysc R8A779A0_PD_ALWAYS_ON>;
+			resets = <&cpg 401>;
+			status = "disabled";
+
+			ports {
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				port@0 {
+					reg = <0>;
+				};
+
+				port@1 {
+					reg = <1>;
+					csi42isp2: endpoint {
+						remote-endpoint = <&isp2csi42>;
+					};
+				};
+			};
+		};
+
+		csi43: csi2@fed70000 {
+			compatible = "renesas,r8a779a0-csi2";
+			reg = <0 0xfed70000 0 0x10000>;
+			interrupts = <GIC_SPI 195 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&cpg CPG_MOD 402>;
+			power-domains = <&sysc R8A779A0_PD_ALWAYS_ON>;
+			resets = <&cpg 402>;
+			status = "disabled";
+
+			ports {
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				port@0 {
+					reg = <0>;
+				};
+
+				port@1 {
+					reg = <1>;
+					csi43isp3: endpoint {
+						remote-endpoint = <&isp3csi43>;
+					};
+				};
+			};
+		};
+
+		isp0: isp@fed00000 {
+			compatible = "renesas,r8a779a0-isp";
+			reg = <0 0xfed00000 0 0x10000>;
+			interrupts = <GIC_SPI 153 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&cpg CPG_MOD 612>;
+			power-domains = <&sysc R8A779A0_PD_A3ISP01>;
+			resets = <&cpg 612>;
+			status = "disabled";
+
+			ports {
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				port@0 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+
+					reg = <0>;
+
+					isp0csi40: endpoint@0 {
+						reg = <0>;
+						remote-endpoint = <&csi40isp0>;
+					};
+				};
+
+				port@1 {
+					reg = <1>;
+					isp0vin00: endpoint {
+						remote-endpoint = <&vin00isp0>;
+					};
+				};
+
+				port@2 {
+					reg = <2>;
+					isp0vin01: endpoint {
+						remote-endpoint = <&vin01isp0>;
+					};
+				};
+
+				port@3 {
+					reg = <3>;
+					isp0vin02: endpoint {
+						remote-endpoint = <&vin02isp0>;
+					};
+				};
+
+				port@4 {
+					reg = <4>;
+					isp0vin03: endpoint {
+						remote-endpoint = <&vin03isp0>;
+					};
+				};
+
+				port@5 {
+					reg = <5>;
+					isp0vin04: endpoint {
+						remote-endpoint = <&vin04isp0>;
+					};
+				};
+
+				port@6 {
+					reg = <6>;
+					isp0vin05: endpoint {
+						remote-endpoint = <&vin05isp0>;
+					};
+				};
+
+				port@7 {
+					reg = <7>;
+					isp0vin06: endpoint {
+						remote-endpoint = <&vin06isp0>;
+					};
+				};
+
+				port@8 {
+					reg = <8>;
+					isp0vin07: endpoint {
+						remote-endpoint = <&vin07isp0>;
+					};
+				};
+			};
+		};
+
+		isp1: isp@fed20000 {
+			compatible = "renesas,r8a779a0-isp";
+			reg = <0 0xfed20000 0 0x10000>;
+			interrupts = <GIC_SPI 155 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&cpg CPG_MOD 613>;
+			power-domains = <&sysc R8A779A0_PD_A3ISP01>;
+			resets = <&cpg 613>;
+			status = "disabled";
+
+			ports {
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				port@0 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+
+					reg = <0>;
+
+					isp1csi41: endpoint@1 {
+						reg = <1>;
+						remote-endpoint = <&csi41isp1>;
+					};
+				};
+
+				port@1 {
+					reg = <1>;
+					isp1vin08: endpoint {
+						remote-endpoint = <&vin08isp1>;
+					};
+				};
+
+				port@2 {
+					reg = <2>;
+					isp1vin09: endpoint {
+						remote-endpoint = <&vin09isp1>;
+					};
+				};
+
+				port@3 {
+					reg = <3>;
+					isp1vin10: endpoint {
+						remote-endpoint = <&vin10isp1>;
+					};
+				};
+
+				port@4 {
+					reg = <4>;
+					isp1vin11: endpoint {
+						remote-endpoint = <&vin11isp1>;
+					};
+				};
+
+				port@5 {
+					reg = <5>;
+					isp1vin12: endpoint {
+						remote-endpoint = <&vin12isp1>;
+					};
+				};
+
+				port@6 {
+					reg = <6>;
+					isp1vin13: endpoint {
+						remote-endpoint = <&vin13isp1>;
+					};
+				};
+
+				port@7 {
+					reg = <7>;
+					isp1vin14: endpoint {
+						remote-endpoint = <&vin14isp1>;
+					};
+				};
+
+				port@8 {
+					reg = <8>;
+					isp1vin15: endpoint {
+						remote-endpoint = <&vin15isp1>;
+					};
+				};
+			};
+		};
+
+		isp2: isp@fed30000 {
+			compatible = "renesas,r8a779a0-isp";
+			reg = <0 0xfed30000 0 0x10000>;
+			interrupts = <GIC_SPI 157 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&cpg CPG_MOD 614>;
+			power-domains = <&sysc R8A779A0_PD_A3ISP23>;
+			resets = <&cpg 614>;
+			status = "disabled";
+
+			ports {
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				port@0 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+
+					reg = <0>;
+
+					isp2csi42: endpoint@0 {
+						reg = <0>;
+						remote-endpoint = <&csi42isp2>;
+					};
+				};
+
+				port@1 {
+					reg = <1>;
+					isp2vin16: endpoint {
+						remote-endpoint = <&vin16isp2>;
+					};
+				};
+
+				port@2 {
+					reg = <2>;
+					isp2vin17: endpoint {
+						remote-endpoint = <&vin17isp2>;
+					};
+				};
+
+				port@3 {
+					reg = <3>;
+					isp2vin18: endpoint {
+						remote-endpoint = <&vin18isp2>;
+					};
+				};
+
+				port@4 {
+					reg = <4>;
+					isp2vin19: endpoint {
+						remote-endpoint = <&vin19isp2>;
+					};
+				};
+
+				port@5 {
+					reg = <5>;
+					isp2vin20: endpoint {
+						remote-endpoint = <&vin20isp2>;
+					};
+				};
+
+				port@6 {
+					reg = <6>;
+					isp2vin21: endpoint {
+						remote-endpoint = <&vin21isp2>;
+					};
+				};
+
+				port@7 {
+					reg = <7>;
+					isp2vin22: endpoint {
+						remote-endpoint = <&vin22isp2>;
+					};
+				};
+
+				port@8 {
+					reg = <8>;
+					isp2vin23: endpoint {
+						remote-endpoint = <&vin23isp2>;
+					};
+				};
+			};
+		};
+
+		isp3: isp@fed40000 {
+			compatible = "renesas,r8a779a0-isp";
+			reg = <0 0xfed40000 0 0x10000>;
+			interrupts = <GIC_SPI 159 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&cpg CPG_MOD 615>;
+			power-domains = <&sysc R8A779A0_PD_A3ISP23>;
+			resets = <&cpg 615>;
+			status = "disabled";
+
+			ports {
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				port@0 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+
+					reg = <0>;
+
+					isp3csi43: endpoint@1 {
+						reg = <1>;
+						remote-endpoint = <&csi43isp3>;
+					};
+				};
+
+				port@1 {
+					reg = <1>;
+					isp3vin24: endpoint {
+						remote-endpoint = <&vin24isp3>;
+					};
+				};
+
+				port@2 {
+					reg = <2>;
+					isp3vin25: endpoint {
+						remote-endpoint = <&vin25isp3>;
+					};
+				};
+
+				port@3 {
+					reg = <3>;
+					isp3vin26: endpoint {
+						remote-endpoint = <&vin26isp3>;
+					};
+				};
+
+				port@4 {
+					reg = <4>;
+					isp3vin27: endpoint {
+						remote-endpoint = <&vin27isp3>;
+					};
+				};
+
+				port@5 {
+					reg = <5>;
+					isp3vin28: endpoint {
+						remote-endpoint = <&vin28isp3>;
+					};
+				};
+
+				port@6 {
+					reg = <6>;
+					isp3vin29: endpoint {
+						remote-endpoint = <&vin29isp3>;
+					};
+				};
+
+				port@7 {
+					reg = <7>;
+					isp3vin30: endpoint {
+						remote-endpoint = <&vin30isp3>;
+					};
+				};
+
+				port@8 {
+					reg = <8>;
+					isp3vin31: endpoint {
+						remote-endpoint = <&vin31isp3>;
+					};
+				};
+			};
+		};
+
 		prr: chipid@fff00044 {
 			compatible = "renesas,prr";
 			reg = <0 0xfff00044 0 4>;
diff --git a/arch/arm64/boot/dts/renesas/r8a779m0.dtsi b/arch/arm64/boot/dts/renesas/r8a779m0.dtsi
new file mode 100644
index 000000000000..6fb1979cc041
--- /dev/null
+++ b/arch/arm64/boot/dts/renesas/r8a779m0.dtsi
@@ -0,0 +1,12 @@
+// SPDX-License-Identifier: (GPL-2.0 or MIT)
+/*
+ * Device Tree Source for the R-Car H3e (R8A779M0) SoC
+ *
+ * Copyright (C) 2021 Glider bv
+ */
+
+#include "r8a77951.dtsi"
+
+/ {
+	compatible = "renesas,r8a779m0", "renesas,r8a7795";
+};
diff --git a/arch/arm64/boot/dts/renesas/r8a779m1.dtsi b/arch/arm64/boot/dts/renesas/r8a779m1.dtsi
index 0e9b04469b83..b6e855f52adf 100644
--- a/arch/arm64/boot/dts/renesas/r8a779m1.dtsi
+++ b/arch/arm64/boot/dts/renesas/r8a779m1.dtsi
@@ -10,3 +10,12 @@
 / {
 	compatible = "renesas,r8a779m1", "renesas,r8a7795";
 };
+
+&cluster0_opp {
+	opp-2000000000 {
+		opp-hz = /bits/ 64 <2000000000>;
+		opp-microvolt = <960000>;
+		clock-latency-ns = <300000>;
+		turbo-mode;
+	};
+};
diff --git a/arch/arm64/boot/dts/renesas/r8a779m2.dtsi b/arch/arm64/boot/dts/renesas/r8a779m2.dtsi
new file mode 100644
index 000000000000..324627340b86
--- /dev/null
+++ b/arch/arm64/boot/dts/renesas/r8a779m2.dtsi
@@ -0,0 +1,12 @@
+// SPDX-License-Identifier: (GPL-2.0 or MIT)
+/*
+ * Device Tree Source for the R-Car M3e (R8A779M2) SoC
+ *
+ * Copyright (C) 2021 Glider bv
+ */
+
+#include "r8a77961.dtsi"
+
+/ {
+	compatible = "renesas,r8a779m2", "renesas,r8a77961";
+};
diff --git a/arch/arm64/boot/dts/renesas/r8a779m3.dtsi b/arch/arm64/boot/dts/renesas/r8a779m3.dtsi
index 65bb6188ccf5..6cff38a6d20b 100644
--- a/arch/arm64/boot/dts/renesas/r8a779m3.dtsi
+++ b/arch/arm64/boot/dts/renesas/r8a779m3.dtsi
@@ -10,3 +10,12 @@
 / {
 	compatible = "renesas,r8a779m3", "renesas,r8a77961";
 };
+
+&cluster0_opp {
+	opp-2000000000 {
+		opp-hz = /bits/ 64 <2000000000>;
+		opp-microvolt = <960000>;
+		clock-latency-ns = <300000>;
+		turbo-mode;
+	};
+};
diff --git a/arch/arm64/boot/dts/renesas/r8a779m4.dtsi b/arch/arm64/boot/dts/renesas/r8a779m4.dtsi
new file mode 100644
index 000000000000..d7fbb6c05502
--- /dev/null
+++ b/arch/arm64/boot/dts/renesas/r8a779m4.dtsi
@@ -0,0 +1,12 @@
+// SPDX-License-Identifier: (GPL-2.0 or MIT)
+/*
+ * Device Tree Source for the R-Car M3Ne (R8A779M4) SoC
+ *
+ * Copyright (C) 2021 Glider bv
+ */
+
+#include "r8a77965.dtsi"
+
+/ {
+	compatible = "renesas,r8a779m4", "renesas,r8a77965";
+};
diff --git a/arch/arm64/boot/dts/renesas/r8a779m5-salvator-xs.dts b/arch/arm64/boot/dts/renesas/r8a779m5-salvator-xs.dts
new file mode 100644
index 000000000000..c0341a88d641
--- /dev/null
+++ b/arch/arm64/boot/dts/renesas/r8a779m5-salvator-xs.dts
@@ -0,0 +1,36 @@
+// SPDX-License-Identifier: (GPL-2.0 or MIT)
+/*
+ * Device Tree Source for the Salvator-X 2nd version board with R-Car M3Ne-2G
+ *
+ * Copyright (C) 2021 Glider bv
+ *
+ * Based on r8a77965-salvator-xs.dts
+ * Copyright (C) 2017 Renesas Electronics Corp.
+ */
+
+/dts-v1/;
+#include "r8a779m5.dtsi"
+#include "salvator-xs.dtsi"
+
+/ {
+	model = "Renesas Salvator-X 2nd version board based on r8a779m5";
+	compatible = "renesas,salvator-xs", "renesas,r8a779m5",
+		     "renesas,r8a77965";
+
+	memory@48000000 {
+		device_type = "memory";
+		/* first 128MB is reserved for secure area. */
+		reg = <0x0 0x48000000 0x0 0x78000000>;
+	};
+};
+
+&du {
+	clocks = <&cpg CPG_MOD 724>,
+		 <&cpg CPG_MOD 723>,
+		 <&cpg CPG_MOD 721>,
+		 <&versaclock6 1>,
+		 <&x21_clk>,
+		 <&versaclock6 2>;
+	clock-names = "du.0", "du.1", "du.3",
+		      "dclkin.0", "dclkin.1", "dclkin.3";
+};
diff --git a/arch/arm64/boot/dts/renesas/r8a779m5.dtsi b/arch/arm64/boot/dts/renesas/r8a779m5.dtsi
new file mode 100644
index 000000000000..8c9c0557fe77
--- /dev/null
+++ b/arch/arm64/boot/dts/renesas/r8a779m5.dtsi
@@ -0,0 +1,21 @@
+// SPDX-License-Identifier: (GPL-2.0 or MIT)
+/*
+ * Device Tree Source for the R-Car M3Ne-2G (R8A779M5) SoC
+ *
+ * Copyright (C) 2021 Glider bv
+ */
+
+#include "r8a77965.dtsi"
+
+/ {
+	compatible = "renesas,r8a779m5", "renesas,r8a77965";
+};
+
+&cluster0_opp {
+	opp-2000000000 {
+		opp-hz = /bits/ 64 <2000000000>;
+		opp-microvolt = <960000>;
+		clock-latency-ns = <300000>;
+		turbo-mode;
+	};
+};
diff --git a/arch/arm64/boot/dts/renesas/r8a779m6.dtsi b/arch/arm64/boot/dts/renesas/r8a779m6.dtsi
new file mode 100644
index 000000000000..afe3cabfb898
--- /dev/null
+++ b/arch/arm64/boot/dts/renesas/r8a779m6.dtsi
@@ -0,0 +1,12 @@
+// SPDX-License-Identifier: (GPL-2.0 or MIT)
+/*
+ * Device Tree Source for the R-Car E3e (R8A779M6) SoC
+ *
+ * Copyright (C) 2021 Glider bv
+ */
+
+#include "r8a77990.dtsi"
+
+/ {
+	compatible = "renesas,r8a779m6", "renesas,r8a77990";
+};
diff --git a/arch/arm64/boot/dts/renesas/r8a779m7.dtsi b/arch/arm64/boot/dts/renesas/r8a779m7.dtsi
new file mode 100644
index 000000000000..4958babc52fd
--- /dev/null
+++ b/arch/arm64/boot/dts/renesas/r8a779m7.dtsi
@@ -0,0 +1,12 @@
+// SPDX-License-Identifier: (GPL-2.0 or MIT)
+/*
+ * Device Tree Source for the R-Car D3e (R8A779M7) SoC
+ *
+ * Copyright (C) 2021 Glider bv
+ */
+
+#include "r8a77995.dtsi"
+
+/ {
+	compatible = "renesas,r8a779m7", "renesas,r8a77995";
+};
diff --git a/arch/arm64/boot/dts/renesas/r8a779m8.dtsi b/arch/arm64/boot/dts/renesas/r8a779m8.dtsi
new file mode 100644
index 000000000000..752440b0c40f
--- /dev/null
+++ b/arch/arm64/boot/dts/renesas/r8a779m8.dtsi
@@ -0,0 +1,12 @@
+// SPDX-License-Identifier: (GPL-2.0 or MIT)
+/*
+ * Device Tree Source for the R-Car H3Ne (R8A779M8) SoC
+ *
+ * Copyright (C) 2021 Glider bv
+ */
+
+#include "r8a77951.dtsi"
+
+/ {
+	compatible = "renesas,r8a779m8", "renesas,r8a7795";
+};
diff --git a/arch/arm64/boot/dts/renesas/r9a07g044.dtsi b/arch/arm64/boot/dts/renesas/r9a07g044.dtsi
index 5f3bc2898daf..485ef5f0fea1 100644
--- a/arch/arm64/boot/dts/renesas/r9a07g044.dtsi
+++ b/arch/arm64/boot/dts/renesas/r9a07g044.dtsi
@@ -13,6 +13,20 @@
 	#address-cells = <2>;
 	#size-cells = <2>;
 
+	audio_clk1: audio_clk1 {
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		/* This value must be overridden by boards that provide it */
+		clock-frequency = <0>;
+	};
+
+	audio_clk2: audio_clk2 {
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		/* This value must be overridden by boards that provide it */
+		clock-frequency = <0>;
+	};
+
 	/* External CAN clock - to be overridden by boards that provide it */
 	can_clk: can {
 		compatible = "fixed-clock";
@@ -78,6 +92,90 @@
 		#size-cells = <2>;
 		ranges;
 
+		ssi0: ssi@10049c00 {
+			compatible = "renesas,r9a07g044-ssi",
+				     "renesas,rz-ssi";
+			reg = <0 0x10049c00 0 0x400>;
+			interrupts = <GIC_SPI 326 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 327 IRQ_TYPE_EDGE_RISING>,
+				     <GIC_SPI 328 IRQ_TYPE_EDGE_RISING>,
+				     <GIC_SPI 329 IRQ_TYPE_EDGE_RISING>;
+			interrupt-names = "int_req", "dma_rx", "dma_tx", "dma_rt";
+			clocks = <&cpg CPG_MOD R9A07G044_SSI0_PCLK2>,
+				 <&cpg CPG_MOD R9A07G044_SSI0_PCLK_SFR>,
+				 <&audio_clk1>, <&audio_clk2>;
+			clock-names = "ssi", "ssi_sfr", "audio_clk1", "audio_clk2";
+			resets = <&cpg R9A07G044_SSI0_RST_M2_REG>;
+			dmas = <&dmac 0x2655>, <&dmac 0x2656>;
+			dma-names = "tx", "rx";
+			power-domains = <&cpg>;
+			#sound-dai-cells = <0>;
+			status = "disabled";
+		};
+
+		ssi1: ssi@1004a000 {
+			compatible = "renesas,r9a07g044-ssi",
+				     "renesas,rz-ssi";
+			reg = <0 0x1004a000 0 0x400>;
+			interrupts = <GIC_SPI 330 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 331 IRQ_TYPE_EDGE_RISING>,
+				     <GIC_SPI 332 IRQ_TYPE_EDGE_RISING>,
+				     <GIC_SPI 333 IRQ_TYPE_EDGE_RISING>;
+			interrupt-names = "int_req", "dma_rx", "dma_tx", "dma_rt";
+			clocks = <&cpg CPG_MOD R9A07G044_SSI1_PCLK2>,
+				 <&cpg CPG_MOD R9A07G044_SSI1_PCLK_SFR>,
+				 <&audio_clk1>, <&audio_clk2>;
+			clock-names = "ssi", "ssi_sfr", "audio_clk1", "audio_clk2";
+			resets = <&cpg R9A07G044_SSI1_RST_M2_REG>;
+			dmas = <&dmac 0x2659>, <&dmac 0x265a>;
+			dma-names = "tx", "rx";
+			power-domains = <&cpg>;
+			#sound-dai-cells = <0>;
+			status = "disabled";
+		};
+
+		ssi2: ssi@1004a400 {
+			compatible = "renesas,r9a07g044-ssi",
+				     "renesas,rz-ssi";
+			reg = <0 0x1004a400 0 0x400>;
+			interrupts = <GIC_SPI 334 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 335 IRQ_TYPE_EDGE_RISING>,
+				     <GIC_SPI 336 IRQ_TYPE_EDGE_RISING>,
+				     <GIC_SPI 337 IRQ_TYPE_EDGE_RISING>;
+			interrupt-names = "int_req", "dma_rx", "dma_tx", "dma_rt";
+			clocks = <&cpg CPG_MOD R9A07G044_SSI2_PCLK2>,
+				 <&cpg CPG_MOD R9A07G044_SSI2_PCLK_SFR>,
+				 <&audio_clk1>, <&audio_clk2>;
+			clock-names = "ssi", "ssi_sfr", "audio_clk1", "audio_clk2";
+			resets = <&cpg R9A07G044_SSI2_RST_M2_REG>;
+			dmas = <&dmac 0x265f>;
+			dma-names = "rt";
+			power-domains = <&cpg>;
+			#sound-dai-cells = <0>;
+			status = "disabled";
+		};
+
+		ssi3: ssi@1004a800 {
+			compatible = "renesas,r9a07g044-ssi",
+				     "renesas,rz-ssi";
+			reg = <0 0x1004a800 0 0x400>;
+			interrupts = <GIC_SPI 338 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 339 IRQ_TYPE_EDGE_RISING>,
+				     <GIC_SPI 340 IRQ_TYPE_EDGE_RISING>,
+				     <GIC_SPI 341 IRQ_TYPE_EDGE_RISING>;
+			interrupt-names = "int_req", "dma_rx", "dma_tx", "dma_rt";
+			clocks = <&cpg CPG_MOD R9A07G044_SSI3_PCLK2>,
+				 <&cpg CPG_MOD R9A07G044_SSI3_PCLK_SFR>,
+				 <&audio_clk1>, <&audio_clk2>;
+			clock-names = "ssi", "ssi_sfr", "audio_clk1", "audio_clk2";
+			resets = <&cpg R9A07G044_SSI3_RST_M2_REG>;
+			dmas = <&dmac 0x2661>, <&dmac 0x2662>;
+			dma-names = "tx", "rx";
+			power-domains = <&cpg>;
+			#sound-dai-cells = <0>;
+			status = "disabled";
+		};
+
 		scif0: serial@1004b800 {
 			compatible = "renesas,scif-r9a07g044";
 			reg = <0 0x1004b800 0 0x400>;
@@ -260,6 +358,23 @@
 			};
 		};
 
+		sbc: spi@10060000 {
+			compatible = "renesas,r9a07g044-rpc-if",
+				     "renesas,rzg2l-rpc-if";
+			reg = <0 0x10060000 0 0x10000>,
+			      <0 0x20000000 0 0x10000000>,
+			      <0 0x10070000 0 0x10000>;
+			reg-names = "regs", "dirmap", "wbuf";
+			interrupts = <GIC_SPI 41 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&cpg CPG_MOD R9A07G044_SPI_CLK2>,
+				 <&cpg CPG_MOD R9A07G044_SPI_CLK>;
+			resets = <&cpg R9A07G044_SPI_RST>;
+			power-domains = <&cpg>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			status = "disabled";
+		};
+
 		cpg: clock-controller@11010000 {
 			compatible = "renesas,r9a07g044-cpg";
 			reg = <0 0x11010000 0 0x10000>;
@@ -295,6 +410,42 @@
 				 <&cpg R9A07G044_GPIO_SPARE_RESETN>;
 		};
 
+		dmac: dma-controller@11820000 {
+			compatible = "renesas,r9a07g044-dmac",
+				     "renesas,rz-dmac";
+			reg = <0 0x11820000 0 0x10000>,
+			      <0 0x11830000 0 0x10000>;
+			interrupts = <GIC_SPI 141 IRQ_TYPE_EDGE_RISING>,
+				     <GIC_SPI 125 IRQ_TYPE_EDGE_RISING>,
+				     <GIC_SPI 126 IRQ_TYPE_EDGE_RISING>,
+				     <GIC_SPI 127 IRQ_TYPE_EDGE_RISING>,
+				     <GIC_SPI 128 IRQ_TYPE_EDGE_RISING>,
+				     <GIC_SPI 129 IRQ_TYPE_EDGE_RISING>,
+				     <GIC_SPI 130 IRQ_TYPE_EDGE_RISING>,
+				     <GIC_SPI 131 IRQ_TYPE_EDGE_RISING>,
+				     <GIC_SPI 132 IRQ_TYPE_EDGE_RISING>,
+				     <GIC_SPI 133 IRQ_TYPE_EDGE_RISING>,
+				     <GIC_SPI 134 IRQ_TYPE_EDGE_RISING>,
+				     <GIC_SPI 135 IRQ_TYPE_EDGE_RISING>,
+				     <GIC_SPI 136 IRQ_TYPE_EDGE_RISING>,
+				     <GIC_SPI 137 IRQ_TYPE_EDGE_RISING>,
+				     <GIC_SPI 138 IRQ_TYPE_EDGE_RISING>,
+				     <GIC_SPI 139 IRQ_TYPE_EDGE_RISING>,
+				     <GIC_SPI 140 IRQ_TYPE_EDGE_RISING>;
+			interrupt-names = "error",
+					  "ch0", "ch1", "ch2", "ch3",
+					  "ch4", "ch5", "ch6", "ch7",
+					  "ch8", "ch9", "ch10", "ch11",
+					  "ch12", "ch13", "ch14", "ch15";
+			clocks = <&cpg CPG_MOD R9A07G044_DMAC_ACLK>,
+				 <&cpg CPG_MOD R9A07G044_DMAC_PCLK>;
+			power-domains = <&cpg>;
+			resets = <&cpg R9A07G044_DMAC_ARESETN>,
+				 <&cpg R9A07G044_DMAC_RST_ASYNC>;
+			#dma-cells = <1>;
+			dma-channels = <16>;
+		};
+
 		gic: interrupt-controller@11900000 {
 			compatible = "arm,gic-v3";
 			#interrupt-cells = <3>;
@@ -304,6 +455,192 @@
 			      <0x0 0x11940000 0 0x60000>;
 			interrupts = <GIC_PPI 9 IRQ_TYPE_LEVEL_LOW>;
 		};
+
+		sdhi0: mmc@11c00000  {
+			compatible = "renesas,sdhi-r9a07g044",
+				     "renesas,rcar-gen3-sdhi";
+			reg = <0x0 0x11c00000 0 0x10000>;
+			interrupts = <GIC_SPI 104 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 105 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&cpg CPG_MOD R9A07G044_SDHI0_IMCLK>,
+				 <&cpg CPG_MOD R9A07G044_SDHI0_IMCLK2>,
+				 <&cpg CPG_MOD R9A07G044_SDHI0_CLK_HS>,
+				 <&cpg CPG_MOD R9A07G044_SDHI0_ACLK>;
+			clock-names = "imclk", "imclk2", "clk_hs", "aclk";
+			resets = <&cpg R9A07G044_SDHI0_IXRST>;
+			power-domains = <&cpg>;
+			status = "disabled";
+		};
+
+		sdhi1: mmc@11c10000 {
+			compatible = "renesas,sdhi-r9a07g044",
+				     "renesas,rcar-gen3-sdhi";
+			reg = <0x0 0x11c10000 0 0x10000>;
+			interrupts = <GIC_SPI 106 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 107 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&cpg CPG_MOD R9A07G044_SDHI1_IMCLK>,
+				 <&cpg CPG_MOD R9A07G044_SDHI1_IMCLK2>,
+				 <&cpg CPG_MOD R9A07G044_SDHI1_CLK_HS>,
+				 <&cpg CPG_MOD R9A07G044_SDHI1_ACLK>;
+			clock-names = "imclk", "imclk2", "clk_hs", "aclk";
+			resets = <&cpg R9A07G044_SDHI1_IXRST>;
+			power-domains = <&cpg>;
+			status = "disabled";
+		};
+
+		eth0: ethernet@11c20000 {
+			compatible = "renesas,r9a07g044-gbeth",
+				     "renesas,rzg2l-gbeth";
+			reg = <0 0x11c20000 0 0x10000>;
+			interrupts = <GIC_SPI 84 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 85 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 86 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "mux", "fil", "arp_ns";
+			phy-mode = "rgmii";
+			clocks = <&cpg CPG_MOD R9A07G044_ETH0_CLK_AXI>,
+				 <&cpg CPG_MOD R9A07G044_ETH0_CLK_CHI>,
+				 <&cpg CPG_CORE R9A07G044_CLK_HP>;
+			clock-names = "axi", "chi", "refclk";
+			resets = <&cpg R9A07G044_ETH0_RST_HW_N>;
+			power-domains = <&cpg>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			status = "disabled";
+		};
+
+		eth1: ethernet@11c30000 {
+			compatible = "renesas,r9a07g044-gbeth",
+				     "renesas,rzg2l-gbeth";
+			reg = <0 0x11c30000 0 0x10000>;
+			interrupts = <GIC_SPI 87 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 88 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 89 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "mux", "fil", "arp_ns";
+			phy-mode = "rgmii";
+			clocks = <&cpg CPG_MOD R9A07G044_ETH1_CLK_AXI>,
+				 <&cpg CPG_MOD R9A07G044_ETH1_CLK_CHI>,
+				 <&cpg CPG_CORE R9A07G044_CLK_HP>;
+			clock-names = "axi", "chi", "refclk";
+			resets = <&cpg R9A07G044_ETH1_RST_HW_N>;
+			power-domains = <&cpg>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			status = "disabled";
+		};
+
+		phyrst: usbphy-ctrl@11c40000 {
+			compatible = "renesas,r9a07g044-usbphy-ctrl",
+				     "renesas,rzg2l-usbphy-ctrl";
+			reg = <0 0x11c40000 0 0x10000>;
+			clocks = <&cpg CPG_MOD R9A07G044_USB_PCLK>;
+			resets = <&cpg R9A07G044_USB_PRESETN>;
+			power-domains = <&cpg>;
+			#reset-cells = <1>;
+			status = "disabled";
+		};
+
+		ohci0: usb@11c50000 {
+			compatible = "generic-ohci";
+			reg = <0 0x11c50000 0 0x100>;
+			interrupts = <GIC_SPI 91 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&cpg CPG_MOD R9A07G044_USB_PCLK>,
+				 <&cpg CPG_MOD R9A07G044_USB_U2H0_HCLK>;
+			resets = <&phyrst 0>,
+				 <&cpg R9A07G044_USB_U2H0_HRESETN>;
+			phys = <&usb2_phy0 1>;
+			phy-names = "usb";
+			power-domains = <&cpg>;
+			status = "disabled";
+		};
+
+		ohci1: usb@11c70000 {
+			compatible = "generic-ohci";
+			reg = <0 0x11c70000 0 0x100>;
+			interrupts = <GIC_SPI 96 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&cpg CPG_MOD R9A07G044_USB_PCLK>,
+				 <&cpg CPG_MOD R9A07G044_USB_U2H1_HCLK>;
+			resets = <&phyrst 1>,
+				 <&cpg R9A07G044_USB_U2H1_HRESETN>;
+			phys = <&usb2_phy1 1>;
+			phy-names = "usb";
+			power-domains = <&cpg>;
+			status = "disabled";
+		};
+
+		ehci0: usb@11c50100 {
+			compatible = "generic-ehci";
+			reg = <0 0x11c50100 0 0x100>;
+			interrupts = <GIC_SPI 92 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&cpg CPG_MOD R9A07G044_USB_PCLK>,
+				 <&cpg CPG_MOD R9A07G044_USB_U2H0_HCLK>;
+			resets = <&phyrst 0>,
+				 <&cpg R9A07G044_USB_U2H0_HRESETN>;
+			phys = <&usb2_phy0 2>;
+			phy-names = "usb";
+			companion = <&ohci0>;
+			power-domains = <&cpg>;
+			status = "disabled";
+		};
+
+		ehci1: usb@11c70100 {
+			compatible = "generic-ehci";
+			reg = <0 0x11c70100 0 0x100>;
+			interrupts = <GIC_SPI 97 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&cpg CPG_MOD R9A07G044_USB_PCLK>,
+				 <&cpg CPG_MOD R9A07G044_USB_U2H1_HCLK>;
+			resets = <&phyrst 1>,
+				 <&cpg R9A07G044_USB_U2H1_HRESETN>;
+			phys = <&usb2_phy1 2>;
+			phy-names = "usb";
+			companion = <&ohci1>;
+			power-domains = <&cpg>;
+			status = "disabled";
+		};
+
+		usb2_phy0: usb-phy@11c50200 {
+			compatible = "renesas,usb2-phy-r9a07g044",
+				     "renesas,rzg2l-usb2-phy";
+			reg = <0 0x11c50200 0 0x700>;
+			interrupts = <GIC_SPI 94 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&cpg CPG_MOD R9A07G044_USB_PCLK>,
+				 <&cpg CPG_MOD R9A07G044_USB_U2H0_HCLK>;
+			resets = <&phyrst 0>;
+			#phy-cells = <1>;
+			power-domains = <&cpg>;
+			status = "disabled";
+		};
+
+		usb2_phy1: usb-phy@11c70200 {
+			compatible = "renesas,usb2-phy-r9a07g044",
+				     "renesas,rzg2l-usb2-phy";
+			reg = <0 0x11c70200 0 0x700>;
+			interrupts = <GIC_SPI 99 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&cpg CPG_MOD R9A07G044_USB_PCLK>,
+				 <&cpg CPG_MOD R9A07G044_USB_U2H1_HCLK>;
+			resets = <&phyrst 1>;
+			#phy-cells = <1>;
+			power-domains = <&cpg>;
+			status = "disabled";
+		};
+
+		hsusb: usb@11c60000 {
+			compatible = "renesas,usbhs-r9a07g044",
+				     "renesas,rza2-usbhs";
+			reg = <0 0x11c60000 0 0x10000>;
+			interrupts = <GIC_SPI 100 IRQ_TYPE_EDGE_RISING>,
+				     <GIC_SPI 101 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 102 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 103 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&cpg CPG_MOD R9A07G044_USB_PCLK>,
+				 <&cpg CPG_MOD R9A07G044_USB_U2P_EXR_CPUCLK>;
+			resets = <&phyrst 0>,
+				 <&cpg R9A07G044_USB_U2P_EXL_SYSRST>;
+			renesas,buswait = <7>;
+			phys = <&usb2_phy0 3>;
+			phy-names = "usb";
+			power-domains = <&cpg>;
+			status = "disabled";
+		};
 	};
 
 	timer {
diff --git a/arch/arm64/boot/dts/renesas/r9a07g044l2-smarc.dts b/arch/arm64/boot/dts/renesas/r9a07g044l2-smarc.dts
index d3f72ec62f03..247b0b3f1b58 100644
--- a/arch/arm64/boot/dts/renesas/r9a07g044l2-smarc.dts
+++ b/arch/arm64/boot/dts/renesas/r9a07g044l2-smarc.dts
@@ -7,15 +7,10 @@
 
 /dts-v1/;
 #include "r9a07g044l2.dtsi"
+#include "rzg2l-smarc-som.dtsi"
 #include "rzg2l-smarc.dtsi"
 
 / {
 	model = "Renesas SMARC EVK based on r9a07g044l2";
 	compatible = "renesas,smarc-evk", "renesas,r9a07g044l2", "renesas,r9a07g044";
-
-	memory@48000000 {
-		device_type = "memory";
-		/* first 128MB is reserved for secure area. */
-		reg = <0x0 0x48000000 0x0 0x78000000>;
-	};
 };
diff --git a/arch/arm64/boot/dts/renesas/rzg2l-smarc-som.dtsi b/arch/arm64/boot/dts/renesas/rzg2l-smarc-som.dtsi
new file mode 100644
index 000000000000..7e84a29dddfa
--- /dev/null
+++ b/arch/arm64/boot/dts/renesas/rzg2l-smarc-som.dtsi
@@ -0,0 +1,275 @@
+// SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+/*
+ * Device Tree Source for the RZ/G2L SMARC SOM common parts
+ *
+ * Copyright (C) 2021 Renesas Electronics Corp.
+ */
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/pinctrl/rzg2l-pinctrl.h>
+
+/* SW1[2] should be at position 2/OFF to enable 64 GB eMMC */
+#define EMMC	1
+
+/*
+ * To enable uSD card on CN3,
+ * SW1[2] should be at position 3/ON.
+ * Disable eMMC by setting "#define EMMC	0" above.
+ */
+#define SDHI	(!EMMC)
+
+/ {
+	aliases {
+		ethernet0 = &eth0;
+		ethernet1 = &eth1;
+	};
+
+	chosen {
+		bootargs = "ignore_loglevel rw root=/dev/nfs ip=on";
+	};
+
+	memory@48000000 {
+		device_type = "memory";
+		/* first 128MB is reserved for secure area. */
+		reg = <0x0 0x48000000 0x0 0x78000000>;
+	};
+
+	reg_1p8v: regulator0 {
+		compatible = "regulator-fixed";
+		regulator-name = "fixed-1.8V";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+		regulator-boot-on;
+		regulator-always-on;
+	};
+
+	reg_3p3v: regulator1 {
+		compatible = "regulator-fixed";
+		regulator-name = "fixed-3.3V";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-boot-on;
+		regulator-always-on;
+	};
+
+	vccq_sdhi0: regulator-vccq-sdhi0 {
+		compatible = "regulator-gpio";
+
+		regulator-name = "SDHI0 VccQ";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <3300000>;
+		states = <3300000 1>, <1800000 0>;
+		regulator-boot-on;
+		gpios = <&pinctrl RZG2L_GPIO(39, 0) GPIO_ACTIVE_HIGH>;
+		regulator-always-on;
+	};
+};
+
+&adc {
+	pinctrl-0 = <&adc_pins>;
+	pinctrl-names = "default";
+	status = "okay";
+
+	/delete-node/ channel@6;
+	/delete-node/ channel@7;
+};
+
+&eth0 {
+	pinctrl-0 = <&eth0_pins>;
+	pinctrl-names = "default";
+	phy-handle = <&phy0>;
+	phy-mode = "rgmii-id";
+	status = "okay";
+
+	phy0: ethernet-phy@7 {
+		compatible = "ethernet-phy-id0022.1640",
+			     "ethernet-phy-ieee802.3-c22";
+		reg = <7>;
+		rxc-skew-psec = <2400>;
+		txc-skew-psec = <2400>;
+		rxdv-skew-psec = <0>;
+		txdv-skew-psec = <0>;
+		rxd0-skew-psec = <0>;
+		rxd1-skew-psec = <0>;
+		rxd2-skew-psec = <0>;
+		rxd3-skew-psec = <0>;
+		txd0-skew-psec = <0>;
+		txd1-skew-psec = <0>;
+		txd2-skew-psec = <0>;
+		txd3-skew-psec = <0>;
+	};
+};
+
+&eth1 {
+	pinctrl-0 = <&eth1_pins>;
+	pinctrl-names = "default";
+	phy-handle = <&phy1>;
+	phy-mode = "rgmii-id";
+	status = "okay";
+
+	phy1: ethernet-phy@7 {
+		compatible = "ethernet-phy-id0022.1640",
+			     "ethernet-phy-ieee802.3-c22";
+		reg = <7>;
+		rxc-skew-psec = <2400>;
+		txc-skew-psec = <2400>;
+		rxdv-skew-psec = <0>;
+		txdv-skew-psec = <0>;
+		rxd0-skew-psec = <0>;
+		rxd1-skew-psec = <0>;
+		rxd2-skew-psec = <0>;
+		rxd3-skew-psec = <0>;
+		txd0-skew-psec = <0>;
+		txd1-skew-psec = <0>;
+		txd2-skew-psec = <0>;
+		txd3-skew-psec = <0>;
+	};
+};
+
+&extal_clk {
+	clock-frequency = <24000000>;
+};
+
+&pinctrl {
+	adc_pins: adc {
+		pinmux = <RZG2L_PORT_PINMUX(9, 0, 2)>; /* ADC_TRG */
+	};
+
+	eth0_pins: eth0 {
+		pinmux = <RZG2L_PORT_PINMUX(28, 1, 1)>, /* ET0_LINKSTA */
+			 <RZG2L_PORT_PINMUX(27, 1, 1)>, /* ET0_MDC */
+			 <RZG2L_PORT_PINMUX(28, 0, 1)>, /* ET0_MDIO */
+			 <RZG2L_PORT_PINMUX(20, 0, 1)>, /* ET0_TXC */
+			 <RZG2L_PORT_PINMUX(20, 1, 1)>, /* ET0_TX_CTL */
+			 <RZG2L_PORT_PINMUX(20, 2, 1)>, /* ET0_TXD0 */
+			 <RZG2L_PORT_PINMUX(21, 0, 1)>, /* ET0_TXD1 */
+			 <RZG2L_PORT_PINMUX(21, 1, 1)>, /* ET0_TXD2 */
+			 <RZG2L_PORT_PINMUX(22, 0, 1)>, /* ET0_TXD3 */
+			 <RZG2L_PORT_PINMUX(24, 0, 1)>, /* ET0_RXC */
+			 <RZG2L_PORT_PINMUX(24, 1, 1)>, /* ET0_RX_CTL */
+			 <RZG2L_PORT_PINMUX(25, 0, 1)>, /* ET0_RXD0 */
+			 <RZG2L_PORT_PINMUX(25, 1, 1)>, /* ET0_RXD1 */
+			 <RZG2L_PORT_PINMUX(26, 0, 1)>, /* ET0_RXD2 */
+			 <RZG2L_PORT_PINMUX(26, 1, 1)>; /* ET0_RXD3 */
+	};
+
+	eth1_pins: eth1 {
+		pinmux = <RZG2L_PORT_PINMUX(37, 2, 1)>, /* ET1_LINKSTA */
+			 <RZG2L_PORT_PINMUX(37, 0, 1)>, /* ET1_MDC */
+			 <RZG2L_PORT_PINMUX(37, 1, 1)>, /* ET1_MDIO */
+			 <RZG2L_PORT_PINMUX(29, 0, 1)>, /* ET1_TXC */
+			 <RZG2L_PORT_PINMUX(29, 1, 1)>, /* ET1_TX_CTL */
+			 <RZG2L_PORT_PINMUX(30, 0, 1)>, /* ET1_TXD0 */
+			 <RZG2L_PORT_PINMUX(30, 1, 1)>, /* ET1_TXD1 */
+			 <RZG2L_PORT_PINMUX(31, 0, 1)>, /* ET1_TXD2 */
+			 <RZG2L_PORT_PINMUX(31, 1, 1)>, /* ET1_TXD3 */
+			 <RZG2L_PORT_PINMUX(33, 1, 1)>, /* ET1_RXC */
+			 <RZG2L_PORT_PINMUX(34, 0, 1)>, /* ET1_RX_CTL */
+			 <RZG2L_PORT_PINMUX(34, 1, 1)>, /* ET1_RXD0 */
+			 <RZG2L_PORT_PINMUX(35, 0, 1)>, /* ET1_RXD1 */
+			 <RZG2L_PORT_PINMUX(35, 1, 1)>, /* ET1_RXD2 */
+			 <RZG2L_PORT_PINMUX(36, 0, 1)>; /* ET1_RXD3 */
+	};
+
+	gpio-sd0-pwr-en-hog {
+		gpio-hog;
+		gpios = <RZG2L_GPIO(4, 1) GPIO_ACTIVE_HIGH>;
+		output-high;
+		line-name = "gpio_sd0_pwr_en";
+	};
+
+	/*
+	 * SD0 device selection is XOR between GPIO_SD0_DEV_SEL and SW1[2]
+	 * The below switch logic can be used to select the device between
+	 * eMMC and microSD, after setting GPIO_SD0_DEV_SEL to high in DT.
+	 * SW1[2] should be at position 2/OFF to enable 64 GB eMMC
+	 * SW1[2] should be at position 3/ON to enable uSD card CN3
+	 */
+	sd0-dev-sel-hog {
+		gpio-hog;
+		gpios = <RZG2L_GPIO(41, 1) GPIO_ACTIVE_HIGH>;
+		output-high;
+		line-name = "sd0_dev_sel";
+	};
+
+	sdhi0_emmc_pins: sd0emmc {
+		sd0_emmc_data {
+			pins = "SD0_DATA0", "SD0_DATA1", "SD0_DATA2", "SD0_DATA3",
+			       "SD0_DATA4", "SD0_DATA5", "SD0_DATA6", "SD0_DATA7";
+			power-source = <1800>;
+		};
+
+		sd0_emmc_ctrl {
+			pins = "SD0_CLK", "SD0_CMD";
+			power-source = <1800>;
+		};
+
+		sd0_emmc_rst {
+			pins = "SD0_RST#";
+			power-source = <1800>;
+		};
+	};
+
+	sdhi0_pins: sd0 {
+		sd0_data {
+			pins = "SD0_DATA0", "SD0_DATA1", "SD0_DATA2", "SD0_DATA3";
+			power-source = <3300>;
+		};
+
+		sd0_ctrl {
+			pins = "SD0_CLK", "SD0_CMD";
+			power-source = <3300>;
+		};
+
+		sd0_mux {
+			pinmux = <RZG2L_PORT_PINMUX(47, 0, 2)>; /* SD0_CD */
+		};
+	};
+
+	sdhi0_pins_uhs: sd0_uhs {
+		sd0_data_uhs {
+			pins = "SD0_DATA0", "SD0_DATA1", "SD0_DATA2", "SD0_DATA3";
+			power-source = <1800>;
+		};
+
+		sd0_ctrl_uhs {
+			pins = "SD0_CLK", "SD0_CMD";
+			power-source = <1800>;
+		};
+
+		sd0_mux_uhs {
+			pinmux = <RZG2L_PORT_PINMUX(47, 0, 2)>; /* SD0_CD */
+		};
+	};
+};
+
+#if SDHI
+&sdhi0 {
+	pinctrl-0 = <&sdhi0_pins>;
+	pinctrl-1 = <&sdhi0_pins_uhs>;
+	pinctrl-names = "default", "state_uhs";
+
+	vmmc-supply = <&reg_3p3v>;
+	vqmmc-supply = <&vccq_sdhi0>;
+	bus-width = <4>;
+	sd-uhs-sdr50;
+	sd-uhs-sdr104;
+	status = "okay";
+};
+#endif
+
+#if EMMC
+&sdhi0 {
+	pinctrl-0 = <&sdhi0_emmc_pins>;
+	pinctrl-1 = <&sdhi0_emmc_pins>;
+	pinctrl-names = "default", "state_uhs";
+
+	vmmc-supply = <&reg_3p3v>;
+	vqmmc-supply = <&reg_1p8v>;
+	bus-width = <8>;
+	mmc-hs200-1_8v;
+	non-removable;
+	fixed-emmc-driver-type = <1>;
+	status = "okay";
+};
+#endif
diff --git a/arch/arm64/boot/dts/renesas/rzg2l-smarc.dtsi b/arch/arm64/boot/dts/renesas/rzg2l-smarc.dtsi
index adcd4f50519e..2863e487a640 100644
--- a/arch/arm64/boot/dts/renesas/rzg2l-smarc.dtsi
+++ b/arch/arm64/boot/dts/renesas/rzg2l-smarc.dtsi
@@ -6,22 +6,308 @@
  */
 
 #include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/pinctrl/rzg2l-pinctrl.h>
+
+/*
+ * SSI-WM8978
+ *
+ * This command is required when Playback/Capture
+ *
+ *	amixer cset name='Left Input Mixer L2 Switch' on
+ *	amixer cset name='Right Input Mixer R2 Switch' on
+ *	amixer cset name='Headphone Playback Volume' 100
+ *	amixer cset name='PCM Volume' 100%
+ *	amixer cset name='Input PGA Volume' 25
+ *
+ */
 
 / {
 	aliases {
 		serial0 = &scif0;
+		i2c0 = &i2c0;
+		i2c1 = &i2c1;
+		i2c3 = &i2c3;
 	};
 
 	chosen {
-		bootargs = "ignore_loglevel";
 		stdout-path = "serial0:115200n8";
 	};
+
+	audio_mclock: audio_mclock {
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <11289600>;
+	};
+
+	snd_rzg2l: sound {
+		compatible = "simple-audio-card";
+		simple-audio-card,format = "i2s";
+		simple-audio-card,bitclock-master = <&cpu_dai>;
+		simple-audio-card,frame-master = <&cpu_dai>;
+		simple-audio-card,mclk-fs = <256>;
+
+		simple-audio-card,widgets = "Microphone", "Microphone Jack";
+		simple-audio-card,routing =
+			    "L2", "Mic Bias",
+			    "R2", "Mic Bias",
+			    "Mic Bias", "Microphone Jack";
+
+		cpu_dai: simple-audio-card,cpu {
+			sound-dai = <&ssi0>;
+		};
+
+		codec_dai: simple-audio-card,codec {
+			clocks = <&audio_mclock>;
+			sound-dai = <&wm8978>;
+		};
+	};
+
+	usb0_vbus_otg: regulator-usb0-vbus-otg {
+		compatible = "regulator-fixed";
+
+		regulator-name = "USB0_VBUS_OTG";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+	};
+
+	vccq_sdhi1: regulator-vccq-sdhi1 {
+		compatible = "regulator-gpio";
+		regulator-name = "SDHI1 VccQ";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <3300000>;
+		gpios = <&pinctrl RZG2L_GPIO(39, 1) GPIO_ACTIVE_HIGH>;
+		gpios-states = <1>;
+		states = <3300000 1>, <1800000 0>;
+	};
+};
+
+&audio_clk1{
+	clock-frequency = <11289600>;
+};
+
+&audio_clk2{
+	clock-frequency = <12288000>;
+};
+
+&canfd {
+	pinctrl-0 = <&can0_pins &can1_pins>;
+	pinctrl-names = "default";
+	status = "okay";
+
+	channel0 {
+		status = "okay";
+	};
+
+	channel1 {
+		status = "okay";
+	};
+};
+
+&ehci0 {
+	dr_mode = "otg";
+	status = "okay";
+};
+
+&ehci1 {
+	status = "okay";
+};
+
+&hsusb {
+	dr_mode = "otg";
+	status = "okay";
+};
+
+&i2c0 {
+	pinctrl-0 = <&i2c0_pins>;
+	pinctrl-names = "default";
+
+	status = "okay";
+};
+
+&i2c1 {
+	pinctrl-0 = <&i2c1_pins>;
+	pinctrl-names = "default";
+
+	status = "okay";
+};
+
+&i2c3 {
+	pinctrl-0 = <&i2c3_pins>;
+	pinctrl-names = "default";
+	clock-frequency = <400000>;
+
+	status = "okay";
+
+	wm8978: codec@1a {
+		compatible = "wlf,wm8978";
+		#sound-dai-cells = <0>;
+		reg = <0x1a>;
+	};
 };
 
-&extal_clk {
-	clock-frequency = <24000000>;
+&ohci0 {
+	dr_mode = "otg";
+	status = "okay";
+};
+
+&ohci1 {
+	status = "okay";
+};
+
+&phyrst {
+	status = "okay";
+};
+
+&pinctrl {
+	pinctrl-0 = <&sound_clk_pins>;
+	pinctrl-names = "default";
+
+	can0_pins: can0 {
+		pinmux = <RZG2L_PORT_PINMUX(10, 1, 2)>, /* TX */
+			 <RZG2L_PORT_PINMUX(11, 0, 2)>; /* RX */
+	};
+
+	/* SW7 should be at position 2->3 so that GPIO8_CAN0_STB line is activated */
+	can0-stb {
+		gpio-hog;
+		gpios = <RZG2L_GPIO(42, 2) GPIO_ACTIVE_HIGH>;
+		output-low;
+		line-name = "can0_stb";
+	};
+
+	can1_pins: can1 {
+		pinmux = <RZG2L_PORT_PINMUX(12, 1, 2)>, /* TX */
+			 <RZG2L_PORT_PINMUX(13, 0, 2)>; /* RX */
+	};
+
+	/* SW8 should be at position 2->3 so that GPIO9_CAN1_STB line is activated */
+	can1-stb {
+		gpio-hog;
+		gpios = <RZG2L_GPIO(42, 3) GPIO_ACTIVE_HIGH>;
+		output-low;
+		line-name = "can1_stb";
+	};
+
+	i2c0_pins: i2c0 {
+		pins = "RIIC0_SDA", "RIIC0_SCL";
+		input-enable;
+	};
+
+	i2c1_pins: i2c1 {
+		pins = "RIIC1_SDA", "RIIC1_SCL";
+		input-enable;
+	};
+
+	i2c3_pins: i2c3 {
+		pinmux = <RZG2L_PORT_PINMUX(18, 0, 3)>, /* SDA */
+			 <RZG2L_PORT_PINMUX(18, 1, 3)>; /* SCL */
+	};
+
+	scif0_pins: scif0 {
+		pinmux = <RZG2L_PORT_PINMUX(38, 0, 1)>,	/* TxD */
+			 <RZG2L_PORT_PINMUX(38, 1, 1)>;	/* RxD */
+	};
+
+	sd1-pwr-en-hog {
+		gpio-hog;
+		gpios = <RZG2L_GPIO(39, 2) GPIO_ACTIVE_HIGH>;
+		output-high;
+		line-name = "sd1_pwr_en";
+	};
+
+	sdhi1_pins: sd1 {
+		sd1_data {
+			pins = "SD1_DATA0", "SD1_DATA1", "SD1_DATA2", "SD1_DATA3";
+			power-source = <3300>;
+		};
+
+		sd1_ctrl {
+			pins = "SD1_CLK", "SD1_CMD";
+			power-source = <3300>;
+		};
+
+		sd1_mux {
+			pinmux = <RZG2L_PORT_PINMUX(19, 0, 1)>; /* SD1_CD */
+		};
+	};
+
+	sdhi1_pins_uhs: sd1_uhs {
+		sd1_data_uhs {
+			pins = "SD1_DATA0", "SD1_DATA1", "SD1_DATA2", "SD1_DATA3";
+			power-source = <1800>;
+		};
+
+		sd1_ctrl_uhs {
+			pins = "SD1_CLK", "SD1_CMD";
+			power-source = <1800>;
+		};
+
+		sd1_mux_uhs {
+			pinmux = <RZG2L_PORT_PINMUX(19, 0, 1)>; /* SD1_CD */
+		};
+	};
+
+	sound_clk_pins: sound_clk {
+		pins = "AUDIO_CLK1", "AUDIO_CLK2";
+		input-enable;
+	};
+
+	ssi0_pins: ssi0 {
+		pinmux = <RZG2L_PORT_PINMUX(45, 0, 1)>, /* BCK */
+			 <RZG2L_PORT_PINMUX(45, 1, 1)>, /* RCK */
+			 <RZG2L_PORT_PINMUX(45, 2, 1)>, /* TXD */
+			 <RZG2L_PORT_PINMUX(45, 3, 1)>; /* RXD */
+	};
+
+	usb0_pins: usb0 {
+		pinmux = <RZG2L_PORT_PINMUX(4, 0, 1)>, /* VBUS */
+			 <RZG2L_PORT_PINMUX(5, 0, 1)>, /* OVC */
+			 <RZG2L_PORT_PINMUX(5, 1, 1)>; /* OTG_ID */
+	};
+
+	usb1_pins: usb1 {
+		pinmux = <RZG2L_PORT_PINMUX(42, 0, 1)>, /* VBUS */
+			 <RZG2L_PORT_PINMUX(42, 1, 1)>; /* OVC */
+	};
 };
 
 &scif0 {
+	pinctrl-0 = <&scif0_pins>;
+	pinctrl-names = "default";
+	status = "okay";
+};
+
+&sdhi1 {
+	pinctrl-0 = <&sdhi1_pins>;
+	pinctrl-1 = <&sdhi1_pins_uhs>;
+	pinctrl-names = "default", "state_uhs";
+
+	vmmc-supply = <&reg_3p3v>;
+	vqmmc-supply = <&vccq_sdhi1>;
+	bus-width = <4>;
+	sd-uhs-sdr50;
+	sd-uhs-sdr104;
+	status = "okay";
+};
+
+&ssi0 {
+	pinctrl-0 = <&ssi0_pins>;
+	pinctrl-names = "default";
+
+	status = "okay";
+};
+
+&usb2_phy0 {
+	pinctrl-0 = <&usb0_pins>;
+	pinctrl-names = "default";
+
+	vbus-supply = <&usb0_vbus_otg>;
+	status = "okay";
+};
+
+&usb2_phy1 {
+	pinctrl-0 = <&usb1_pins>;
+	pinctrl-names = "default";
+
 	status = "okay";
 };
diff --git a/arch/arm64/boot/dts/renesas/salvator-common.dtsi b/arch/arm64/boot/dts/renesas/salvator-common.dtsi
index eb1f3b82300b..bf37777dca31 100644
--- a/arch/arm64/boot/dts/renesas/salvator-common.dtsi
+++ b/arch/arm64/boot/dts/renesas/salvator-common.dtsi
@@ -340,6 +340,8 @@
 	status = "okay";
 
 	phy0: ethernet-phy@0 {
+		compatible = "ethernet-phy-id0022.1622",
+			     "ethernet-phy-ieee802.3-c22";
 		rxc-skew-ps = <1500>;
 		reg = <0>;
 		interrupt-parent = <&gpio2>;
@@ -524,47 +526,49 @@
 		reg-names = "main", "dpll", "cp", "hdmi", "edid", "repeater",
 			    "infoframe", "cbus", "cec", "sdp", "txa", "txb" ;
 
-		#address-cells = <1>;
-		#size-cells = <0>;
-
 		interrupt-parent = <&gpio6>;
 		interrupt-names = "intrq1", "intrq2";
 		interrupts = <30 IRQ_TYPE_LEVEL_LOW>,
 			     <31 IRQ_TYPE_LEVEL_LOW>;
 
-		port@7 {
-			reg = <7>;
+		ports {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			port@7 {
+				reg = <7>;
 
-			adv7482_ain7: endpoint {
-				remote-endpoint = <&cvbs_con>;
+				adv7482_ain7: endpoint {
+					remote-endpoint = <&cvbs_con>;
+				};
 			};
-		};
 
-		port@8 {
-			reg = <8>;
+			port@8 {
+				reg = <8>;
 
-			adv7482_hdmi: endpoint {
-				remote-endpoint = <&hdmi_in_con>;
+				adv7482_hdmi: endpoint {
+					remote-endpoint = <&hdmi_in_con>;
+				};
 			};
-		};
 
-		port@a {
-			reg = <10>;
+			port@a {
+				reg = <10>;
 
-			adv7482_txa: endpoint {
-				clock-lanes = <0>;
-				data-lanes = <1 2 3 4>;
-				remote-endpoint = <&csi40_in>;
+				adv7482_txa: endpoint {
+					clock-lanes = <0>;
+					data-lanes = <1 2 3 4>;
+					remote-endpoint = <&csi40_in>;
+				};
 			};
-		};
 
-		port@b {
-			reg = <11>;
+			port@b {
+				reg = <11>;
 
-			adv7482_txb: endpoint {
-				clock-lanes = <0>;
-				data-lanes = <1>;
-				remote-endpoint = <&csi20_in>;
+				adv7482_txb: endpoint {
+					clock-lanes = <0>;
+					data-lanes = <1>;
+					remote-endpoint = <&csi20_in>;
+				};
 			};
 		};
 	};
diff --git a/arch/arm64/boot/dts/renesas/ulcb.dtsi b/arch/arm64/boot/dts/renesas/ulcb.dtsi
index 1f177af3eb9d..7edffe7f8cfa 100644
--- a/arch/arm64/boot/dts/renesas/ulcb.dtsi
+++ b/arch/arm64/boot/dts/renesas/ulcb.dtsi
@@ -154,6 +154,8 @@
 	status = "okay";
 
 	phy0: ethernet-phy@0 {
+		compatible = "ethernet-phy-id0022.1622",
+			     "ethernet-phy-ieee802.3-c22";
 		rxc-skew-ps = <1500>;
 		reg = <0>;
 		interrupt-parent = <&gpio2>;
diff --git a/arch/arm64/boot/dts/rockchip/Makefile b/arch/arm64/boot/dts/rockchip/Makefile
index 7fdb41de01ec..479906f3ad7b 100644
--- a/arch/arm64/boot/dts/rockchip/Makefile
+++ b/arch/arm64/boot/dts/rockchip/Makefile
@@ -13,6 +13,7 @@ dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3328-nanopi-r2s.dtb
 dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3328-rock64.dtb
 dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3328-rock-pi-e.dtb
 dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3328-roc-cc.dtb
+dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3328-roc-pc.dtb
 dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3368-evb-act8846.dtb
 dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3368-geekbox.dtb
 dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3368-lion-haikou.dtb
@@ -24,6 +25,7 @@ dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3399-ficus.dtb
 dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3399-firefly.dtb
 dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3399-gru-bob.dtb
 dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3399-gru-kevin.dtb
+dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3399-gru-scarlet-dumo.dtb
 dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3399-gru-scarlet-inx.dtb
 dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3399-gru-scarlet-kd.dtb
 dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3399-hugsun-x99.dtb
@@ -42,8 +44,11 @@ dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3399-pinebook-pro.dtb
 dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3399-puma-haikou.dtb
 dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3399-roc-pc.dtb
 dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3399-roc-pc-mezzanine.dtb
+dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3399-roc-pc-plus.dtb
 dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3399-rock-pi-4a.dtb
+dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3399-rock-pi-4a-plus.dtb
 dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3399-rock-pi-4b.dtb
+dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3399-rock-pi-4b-plus.dtb
 dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3399-rock-pi-4c.dtb
 dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3399-rock960.dtb
 dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3399-rockpro64-v2.dtb
@@ -51,4 +56,5 @@ dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3399-rockpro64.dtb
 dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3399-sapphire.dtb
 dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3399-sapphire-excavator.dtb
 dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3399pro-rock-pi-n10.dtb
+dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3566-quartz64-a.dtb
 dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3568-evb1-v10.dtb
diff --git a/arch/arm64/boot/dts/rockchip/px30-evb.dts b/arch/arm64/boot/dts/rockchip/px30-evb.dts
index c1ce9c295e5b..848bc39cf86a 100644
--- a/arch/arm64/boot/dts/rockchip/px30-evb.dts
+++ b/arch/arm64/boot/dts/rockchip/px30-evb.dts
@@ -114,6 +114,10 @@
 	cpu-supply = <&vdd_arm>;
 };
 
+&csi_dphy {
+	status = "okay";
+};
+
 &display_subsystem {
 	status = "okay";
 };
@@ -428,6 +432,36 @@
 	};
 };
 
+&i2c2 {
+	status = "okay";
+
+	clock-frequency = <100000>;
+
+	/* These are relatively safe rise/fall times; TODO: measure */
+	i2c-scl-falling-time-ns = <50>;
+	i2c-scl-rising-time-ns = <300>;
+
+	ov5695: ov5695@36 {
+		compatible = "ovti,ov5695";
+		reg = <0x36>;
+		avdd-supply = <&vcc2v8_dvp>;
+		clocks = <&cru SCLK_CIF_OUT>;
+		clock-names = "xvclk";
+		dvdd-supply = <&vcc1v5_dvp>;
+		dovdd-supply = <&vcc1v8_dvp>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&cif_clkout_m0>;
+		reset-gpios = <&gpio2 14 GPIO_ACTIVE_LOW>;
+
+		port {
+			ucam_out: endpoint {
+				remote-endpoint = <&mipi_in_ucam>;
+				data-lanes = <1 2>;
+			};
+		};
+	};
+};
+
 &i2s1_2ch {
 	status = "okay";
 };
@@ -443,6 +477,24 @@
 	vccio6-supply = <&vccio_flash>;
 };
 
+&isp {
+	status = "okay";
+
+	ports {
+		port@0 {
+			mipi_in_ucam: endpoint@0 {
+				reg = <0>;
+				data-lanes = <1 2>;
+				remote-endpoint = <&ucam_out>;
+			};
+		};
+	};
+};
+
+&isp_mmu {
+	status = "okay";
+};
+
 &pinctrl {
 	headphone {
 		hp_det: hp-det {
diff --git a/arch/arm64/boot/dts/rockchip/px30.dtsi b/arch/arm64/boot/dts/rockchip/px30.dtsi
index 248ebb61aa79..00f50b05d55a 100644
--- a/arch/arm64/boot/dts/rockchip/px30.dtsi
+++ b/arch/arm64/boot/dts/rockchip/px30.dtsi
@@ -110,7 +110,7 @@
 		};
 	};
 
-	cpu0_opp_table: cpu0-opp-table {
+	cpu0_opp_table: opp-table-0 {
 		compatible = "operating-points-v2";
 		opp-shared;
 
@@ -864,6 +864,19 @@
 		status = "disabled";
 	};
 
+	csi_dphy: phy@ff2f0000 {
+		compatible = "rockchip,px30-csi-dphy";
+		reg = <0x0 0xff2f0000 0x0 0x4000>;
+		clocks = <&cru PCLK_MIPICSIPHY>;
+		clock-names = "pclk";
+		#phy-cells = <0>;
+		power-domains = <&power PX30_PD_VI>;
+		resets = <&cru SRST_MIPICSIPHY_P>;
+		reset-names = "apb";
+		rockchip,grf = <&grf>;
+		status = "disabled";
+	};
+
 	usb20_otg: usb@ff300000 {
 		compatible = "rockchip,px30-usb", "rockchip,rk3066-usb",
 			     "snps,dwc2";
@@ -974,6 +987,18 @@
 		status = "disabled";
 	};
 
+	sfc: spi@ff3a0000 {
+		compatible = "rockchip,sfc";
+		reg = <0x0 0xff3a0000 0x0 0x4000>;
+		interrupts = <GIC_SPI 56 IRQ_TYPE_LEVEL_HIGH>;
+		clocks = <&cru SCLK_SFC>, <&cru HCLK_SFC>;
+		clock-names = "clk_sfc", "hclk_sfc";
+		pinctrl-0 = <&sfc_clk &sfc_cs0 &sfc_bus4>;
+		pinctrl-names = "default";
+		power-domains = <&power PX30_PD_MMC_NAND>;
+		status = "disabled";
+	};
+
 	nfc: nand-controller@ff3b0000 {
 		compatible = "rockchip,px30-nfc";
 		reg = <0x0 0xff3b0000 0x0 0x4000>;
@@ -989,7 +1014,7 @@
 		status = "disabled";
 	};
 
-	gpu_opp_table: opp-table2 {
+	gpu_opp_table: opp-table-1 {
 		compatible = "operating-points-v2";
 
 		opp-200000000 {
@@ -1024,6 +1049,28 @@
 		status = "disabled";
 	};
 
+	vpu: video-codec@ff442000 {
+		compatible = "rockchip,px30-vpu";
+		reg = <0x0 0xff442000 0x0 0x800>;
+		interrupts = <GIC_SPI 80 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 79 IRQ_TYPE_LEVEL_HIGH>;
+		interrupt-names = "vepu", "vdpu";
+		clocks = <&cru ACLK_VPU>, <&cru HCLK_VPU>;
+		clock-names = "aclk", "hclk";
+		iommus = <&vpu_mmu>;
+		power-domains = <&power PX30_PD_VPU>;
+	};
+
+	vpu_mmu: iommu@ff442800 {
+		compatible = "rockchip,iommu";
+		reg = <0x0 0xff442800 0x0 0x100>;
+		interrupts = <GIC_SPI 81 IRQ_TYPE_LEVEL_HIGH>;
+		clocks = <&cru ACLK_VPU>, <&cru HCLK_VPU>;
+		clock-names = "aclk", "iface";
+		#iommu-cells = <0>;
+		power-domains = <&power PX30_PD_VPU>;
+	};
+
 	dsi: dsi@ff450000 {
 		compatible = "rockchip,px30-mipi-dsi";
 		reg = <0x0 0xff450000 0x0 0x10000>;
@@ -1142,6 +1189,47 @@
 		status = "disabled";
 	};
 
+	isp: isp@ff4a0000 {
+		compatible = "rockchip,px30-cif-isp"; /*rk3326-rkisp1*/
+		reg = <0x0 0xff4a0000 0x0 0x8000>;
+		interrupts = <GIC_SPI 70 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 73 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 74 IRQ_TYPE_LEVEL_HIGH>;
+		interrupt-names = "isp", "mi", "mipi";
+		clocks = <&cru SCLK_ISP>,
+			 <&cru ACLK_ISP>,
+			 <&cru HCLK_ISP>,
+			 <&cru PCLK_ISP>;
+		clock-names = "isp", "aclk", "hclk", "pclk";
+		iommus = <&isp_mmu>;
+		phys = <&csi_dphy>;
+		phy-names = "dphy";
+		power-domains = <&power PX30_PD_VI>;
+		status = "disabled";
+
+		ports {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			port@0 {
+				reg = <0>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+			};
+		};
+	};
+
+	isp_mmu: iommu@ff4a8000 {
+		compatible = "rockchip,iommu";
+		reg = <0x0 0xff4a8000 0x0 0x100>;
+		interrupts = <GIC_SPI 70 IRQ_TYPE_LEVEL_HIGH>;
+		clocks = <&cru ACLK_ISP>, <&cru HCLK_ISP>;
+		clock-names = "aclk", "iface";
+		power-domains = <&power PX30_PD_VI>;
+		rockchip,disable-mmu-reset;
+		#iommu-cells = <0>;
+	};
+
 	qos_gmac: qos@ff518000 {
 		compatible = "rockchip,px30-qos", "syscon";
 		reg = <0x0 0xff518000 0x0 0x20>;
@@ -1250,7 +1338,7 @@
 		#size-cells = <2>;
 		ranges;
 
-		gpio0: gpio0@ff040000 {
+		gpio0: gpio@ff040000 {
 			compatible = "rockchip,gpio-bank";
 			reg = <0x0 0xff040000 0x0 0x100>;
 			interrupts = <GIC_SPI 3 IRQ_TYPE_LEVEL_HIGH>;
@@ -1262,7 +1350,7 @@
 			#interrupt-cells = <2>;
 		};
 
-		gpio1: gpio1@ff250000 {
+		gpio1: gpio@ff250000 {
 			compatible = "rockchip,gpio-bank";
 			reg = <0x0 0xff250000 0x0 0x100>;
 			interrupts = <GIC_SPI 4 IRQ_TYPE_LEVEL_HIGH>;
@@ -1274,7 +1362,7 @@
 			#interrupt-cells = <2>;
 		};
 
-		gpio2: gpio2@ff260000 {
+		gpio2: gpio@ff260000 {
 			compatible = "rockchip,gpio-bank";
 			reg = <0x0 0xff260000 0x0 0x100>;
 			interrupts = <GIC_SPI 5 IRQ_TYPE_LEVEL_HIGH>;
@@ -1286,7 +1374,7 @@
 			#interrupt-cells = <2>;
 		};
 
-		gpio3: gpio3@ff270000 {
+		gpio3: gpio@ff270000 {
 			compatible = "rockchip,gpio-bank";
 			reg = <0x0 0xff270000 0x0 0x100>;
 			interrupts = <GIC_SPI 6 IRQ_TYPE_LEVEL_HIGH>;
@@ -1973,6 +2061,32 @@
 			};
 		};
 
+		sfc {
+			sfc_bus4: sfc-bus4 {
+				rockchip,pins =
+					<1 RK_PA0 3 &pcfg_pull_none>,
+					<1 RK_PA1 3 &pcfg_pull_none>,
+					<1 RK_PA2 3 &pcfg_pull_none>,
+					<1 RK_PA3 3 &pcfg_pull_none>;
+			};
+
+			sfc_bus2: sfc-bus2 {
+				rockchip,pins =
+					<1 RK_PA0 3 &pcfg_pull_none>,
+					<1 RK_PA1 3 &pcfg_pull_none>;
+			};
+
+			sfc_cs0: sfc-cs0 {
+				rockchip,pins =
+					<1 RK_PA4 3 &pcfg_pull_none>;
+			};
+
+			sfc_clk: sfc-clk {
+				rockchip,pins =
+					<1 RK_PB1 3 &pcfg_pull_none>;
+			};
+		};
+
 		lcdc {
 			lcdc_rgb_dclk_pin: lcdc-rgb-dclk-pin {
 				rockchip,pins =
diff --git a/arch/arm64/boot/dts/rockchip/rk3308.dtsi b/arch/arm64/boot/dts/rockchip/rk3308.dtsi
index a185901aba9a..1cbe2126186e 100644
--- a/arch/arm64/boot/dts/rockchip/rk3308.dtsi
+++ b/arch/arm64/boot/dts/rockchip/rk3308.dtsi
@@ -99,7 +99,7 @@
 		};
 	};
 
-	cpu0_opp_table: cpu0-opp-table {
+	cpu0_opp_table: opp-table-0 {
 		compatible = "operating-points-v2";
 		opp-shared;
 
@@ -731,6 +731,17 @@
 		status = "disabled";
 	};
 
+	sfc: spi@ff4c0000 {
+		compatible = "rockchip,sfc";
+		reg = <0x0 0xff4c0000 0x0 0x4000>;
+		interrupts = <GIC_SPI 82 IRQ_TYPE_LEVEL_HIGH>;
+		clocks = <&cru SCLK_SFC>, <&cru HCLK_SFC>;
+		clock-names = "clk_sfc", "hclk_sfc";
+		pinctrl-0 = <&sfc_clk &sfc_cs0 &sfc_bus4>;
+		pinctrl-names = "default";
+		status = "disabled";
+	};
+
 	cru: clock-controller@ff500000 {
 		compatible = "rockchip,rk3308-cru";
 		reg = <0x0 0xff500000 0x0 0x1000>;
@@ -779,7 +790,7 @@
 		#size-cells = <2>;
 		ranges;
 
-		gpio0: gpio0@ff220000 {
+		gpio0: gpio@ff220000 {
 			compatible = "rockchip,gpio-bank";
 			reg = <0x0 0xff220000 0x0 0x100>;
 			interrupts = <GIC_SPI 40 IRQ_TYPE_LEVEL_HIGH>;
@@ -790,7 +801,7 @@
 			#interrupt-cells = <2>;
 		};
 
-		gpio1: gpio1@ff230000 {
+		gpio1: gpio@ff230000 {
 			compatible = "rockchip,gpio-bank";
 			reg = <0x0 0xff230000 0x0 0x100>;
 			interrupts = <GIC_SPI 41 IRQ_TYPE_LEVEL_HIGH>;
@@ -801,7 +812,7 @@
 			#interrupt-cells = <2>;
 		};
 
-		gpio2: gpio2@ff240000 {
+		gpio2: gpio@ff240000 {
 			compatible = "rockchip,gpio-bank";
 			reg = <0x0 0xff240000 0x0 0x100>;
 			interrupts = <GIC_SPI 42 IRQ_TYPE_LEVEL_HIGH>;
@@ -812,7 +823,7 @@
 			#interrupt-cells = <2>;
 		};
 
-		gpio3: gpio3@ff250000 {
+		gpio3: gpio@ff250000 {
 			compatible = "rockchip,gpio-bank";
 			reg = <0x0 0xff250000 0x0 0x100>;
 			interrupts = <GIC_SPI 43 IRQ_TYPE_LEVEL_HIGH>;
@@ -823,7 +834,7 @@
 			#interrupt-cells = <2>;
 		};
 
-		gpio4: gpio4@ff260000 {
+		gpio4: gpio@ff260000 {
 			compatible = "rockchip,gpio-bank";
 			reg = <0x0 0xff260000 0x0 0x100>;
 			interrupts = <GIC_SPI 44 IRQ_TYPE_LEVEL_HIGH>;
@@ -1004,6 +1015,32 @@
 			};
 		};
 
+		sfc {
+			sfc_bus4: sfc-bus4 {
+				rockchip,pins =
+					<3 RK_PA0 3 &pcfg_pull_none>,
+					<3 RK_PA1 3 &pcfg_pull_none>,
+					<3 RK_PA2 3 &pcfg_pull_none>,
+					<3 RK_PA3 3 &pcfg_pull_none>;
+			};
+
+			sfc_bus2: sfc-bus2 {
+				rockchip,pins =
+					<3 RK_PA0 3 &pcfg_pull_none>,
+					<3 RK_PA1 3 &pcfg_pull_none>;
+			};
+
+			sfc_cs0: sfc-cs0 {
+				rockchip,pins =
+					<3 RK_PA4 3 &pcfg_pull_none>;
+			};
+
+			sfc_clk: sfc-clk {
+				rockchip,pins =
+					<3 RK_PA5 3 &pcfg_pull_none>;
+			};
+		};
+
 		gmac {
 			rmii_pins: rmii-pins {
 				rockchip,pins =
diff --git a/arch/arm64/boot/dts/rockchip/rk3318-a95x-z2.dts b/arch/arm64/boot/dts/rockchip/rk3318-a95x-z2.dts
index 763cf9b4620e..43c928ac98f0 100644
--- a/arch/arm64/boot/dts/rockchip/rk3318-a95x-z2.dts
+++ b/arch/arm64/boot/dts/rockchip/rk3318-a95x-z2.dts
@@ -185,7 +185,6 @@
 	assigned-clock-parents = <&cru SCLK_MAC2PHY_SRC>;
 	assigned-clock-rate = <50000000>;
 	assigned-clocks = <&cru SCLK_MAC2PHY>;
-	clock_in_out = "output";
 	status = "okay";
 };
 
@@ -194,8 +193,6 @@
 };
 
 &hdmi {
-	ddc-i2c-scl-high-time-ns = <9625>;
-	ddc-i2c-scl-low-time-ns = <10000>;
 	status = "okay";
 };
 
diff --git a/arch/arm64/boot/dts/rockchip/rk3326-odroid-go2.dts b/arch/arm64/boot/dts/rockchip/rk3326-odroid-go2.dts
index 7fc674a99a6c..ea0695b51ecd 100644
--- a/arch/arm64/boot/dts/rockchip/rk3326-odroid-go2.dts
+++ b/arch/arm64/boot/dts/rockchip/rk3326-odroid-go2.dts
@@ -207,7 +207,8 @@
 		gpio = <&gpio0 RK_PB7 GPIO_ACTIVE_HIGH>;
 		enable-active-high;
 		regulator-always-on;
-		vin-supply = <&vccsys>;
+		regulator-boot-on;
+		vin-supply = <&usb_midu>;
 	};
 };
 
@@ -311,6 +312,7 @@
 		vcc5-supply = <&vccsys>;
 		vcc6-supply = <&vccsys>;
 		vcc7-supply = <&vccsys>;
+		vcc8-supply = <&vccsys>;
 
 		regulators {
 			vdd_logic: DCDC_REG1 {
@@ -460,6 +462,14 @@
 					regulator-suspend-microvolt = <3000000>;
 				};
 			};
+
+			usb_midu: BOOST {
+				regulator-name = "usb_midu";
+				regulator-min-microvolt = <5000000>;
+				regulator-max-microvolt = <5400000>;
+				regulator-always-on;
+				regulator-boot-on;
+			};
 		};
 
 		rk817_codec: codec {
@@ -517,6 +527,22 @@
 	status = "okay";
 };
 
+&sfc {
+	pinctrl-0 = <&sfc_clk &sfc_cs0 &sfc_bus2>;
+	pinctrl-names = "default";
+	#address-cells = <1>;
+	#size-cells = <0>;
+	status = "okay";
+
+	flash@0 {
+		compatible = "jedec,spi-nor";
+		reg = <0>;
+		spi-max-frequency = <108000000>;
+		spi-rx-bus-width = <2>;
+		spi-tx-bus-width = <1>;
+	};
+};
+
 &tsadc {
 	status = "okay";
 };
diff --git a/arch/arm64/boot/dts/rockchip/rk3328-roc-pc.dts b/arch/arm64/boot/dts/rockchip/rk3328-roc-pc.dts
new file mode 100644
index 000000000000..e3e3984d01d4
--- /dev/null
+++ b/arch/arm64/boot/dts/rockchip/rk3328-roc-pc.dts
@@ -0,0 +1,110 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+// Copyright (c) 2021 T-Chip Intelligent Technology Co., Ltd
+
+/dts-v1/;
+
+#include <dt-bindings/input/input.h>
+
+#include "rk3328-roc-cc.dts"
+
+/ {
+	model = "Firefly ROC-RK3328-PC";
+	compatible = "firefly,roc-rk3328-pc", "rockchip,rk3328";
+
+	adc-keys {
+		compatible = "adc-keys";
+		io-channels = <&saradc 0>;
+		io-channel-names = "buttons";
+		keyup-threshold-microvolt = <1750000>;
+
+		/* This button is unpopulated out of the factory. */
+		button-recovery {
+			label = "Recovery";
+			linux,code = <KEY_VENDOR>;
+			press-threshold-microvolt = <10000>;
+		};
+	};
+
+	ir-receiver {
+		compatible = "gpio-ir-receiver";
+		gpios = <&gpio2 RK_PA2 GPIO_ACTIVE_LOW>;
+		linux,rc-map-name = "rc-khadas";
+		pinctrl-names = "default";
+		pinctrl-0 = <&ir_int>;
+	};
+
+	sdio_pwrseq: sdio-pwrseq {
+		compatible = "mmc-pwrseq-simple";
+		pinctrl-names = "default";
+		pinctrl-0 = <&wifi_en>, <&wifi_host_wake>;
+		reset-gpios = <&gpio3 RK_PB0 GPIO_ACTIVE_LOW>;
+	};
+};
+
+&codec {
+	mute-gpios = <&grf_gpio 0 GPIO_ACTIVE_LOW>;
+};
+
+&gpu {
+	mali-supply = <&vdd_logic>;
+};
+
+&pinctrl {
+	ir {
+		ir_int: ir-int {
+			rockchip,pins = <2 RK_PA2 RK_FUNC_GPIO &pcfg_pull_none>;
+		};
+	};
+
+	sdmmcio {
+		sdio_per_pin: sdio-per-pin {
+			rockchip,pins = <0 RK_PD3 RK_FUNC_GPIO &pcfg_pull_down>;
+		};
+	};
+
+	wifi {
+		wifi_en: wifi-en {
+			rockchip,pins = <3 RK_PB0 RK_FUNC_GPIO &pcfg_pull_none>;
+		};
+
+		wifi_host_wake: wifi-host-wake {
+			rockchip,pins = <3 RK_PA1 RK_FUNC_GPIO &pcfg_pull_none_4ma>;
+		};
+
+		bt_rst: bt-rst {
+			rockchip,pins = <1 RK_PD0 RK_FUNC_GPIO &pcfg_pull_none>;
+		};
+
+		bt_en: bt-en {
+			rockchip,pins = <1 RK_PD2 RK_FUNC_GPIO &pcfg_pull_none>;
+		};
+	};
+};
+
+&pmic_int_l {
+	rockchip,pins = <0 RK_PA2 RK_FUNC_GPIO &pcfg_pull_up>;
+};
+
+&rk805 {
+	interrupt-parent = <&gpio0>;
+	interrupts = <RK_PA2 IRQ_TYPE_LEVEL_LOW>;
+};
+
+&saradc {
+	vref-supply = <&vcc_18>;
+	status = "okay";
+};
+
+&usb20_host_drv {
+	rockchip,pins = <0 RK_PA0 RK_FUNC_GPIO &pcfg_pull_up>;
+};
+
+&vcc_host1_5v {
+	gpio = <&gpio0 RK_PA0 GPIO_ACTIVE_HIGH>;
+};
+
+&vcc_sdio {
+	gpios = <&gpio0 RK_PD3 GPIO_ACTIVE_HIGH>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&sdio_per_pin>;
+};
diff --git a/arch/arm64/boot/dts/rockchip/rk3328-rock64.dts b/arch/arm64/boot/dts/rockchip/rk3328-rock64.dts
index 1b0f7e4551ea..f69a38f42d2d 100644
--- a/arch/arm64/boot/dts/rockchip/rk3328-rock64.dts
+++ b/arch/arm64/boot/dts/rockchip/rk3328-rock64.dts
@@ -345,7 +345,7 @@
 &spi0 {
 	status = "okay";
 
-	spiflash@0 {
+	flash@0 {
 		compatible = "jedec,spi-nor";
 		reg = <0>;
 
diff --git a/arch/arm64/boot/dts/rockchip/rk3328.dtsi b/arch/arm64/boot/dts/rockchip/rk3328.dtsi
index 8c821acb21ff..39db0b85b4da 100644
--- a/arch/arm64/boot/dts/rockchip/rk3328.dtsi
+++ b/arch/arm64/boot/dts/rockchip/rk3328.dtsi
@@ -105,7 +105,7 @@
 		};
 	};
 
-	cpu0_opp_table: opp_table0 {
+	cpu0_opp_table: opp-table-0 {
 		compatible = "operating-points-v2";
 		opp-shared;
 
@@ -599,7 +599,7 @@
 
 	gpu: gpu@ff300000 {
 		compatible = "rockchip,rk3328-mali", "arm,mali-450";
-		reg = <0x0 0xff300000 0x0 0x40000>;
+		reg = <0x0 0xff300000 0x0 0x30000>;
 		interrupts = <GIC_SPI 90 IRQ_TYPE_LEVEL_HIGH>,
 			     <GIC_SPI 87 IRQ_TYPE_LEVEL_HIGH>,
 			     <GIC_SPI 93 IRQ_TYPE_LEVEL_HIGH>,
@@ -623,7 +623,6 @@
 		compatible = "rockchip,iommu";
 		reg = <0x0 0xff330200 0 0x100>;
 		interrupts = <GIC_SPI 96 IRQ_TYPE_LEVEL_HIGH>;
-		interrupt-names = "h265e_mmu";
 		clocks = <&cru ACLK_H265>, <&cru PCLK_H265>;
 		clock-names = "aclk", "iface";
 		#iommu-cells = <0>;
@@ -634,7 +633,6 @@
 		compatible = "rockchip,iommu";
 		reg = <0x0 0xff340800 0x0 0x40>;
 		interrupts = <GIC_SPI 98 IRQ_TYPE_LEVEL_HIGH>;
-		interrupt-names = "vepu_mmu";
 		clocks = <&cru ACLK_VPU>, <&cru HCLK_VPU>;
 		clock-names = "aclk", "iface";
 		#iommu-cells = <0>;
@@ -656,7 +654,6 @@
 		compatible = "rockchip,iommu";
 		reg = <0x0 0xff350800 0x0 0x40>;
 		interrupts = <GIC_SPI 11 IRQ_TYPE_LEVEL_HIGH>;
-		interrupt-names = "vpu_mmu";
 		clocks = <&cru ACLK_VPU>, <&cru HCLK_VPU>;
 		clock-names = "aclk", "iface";
 		#iommu-cells = <0>;
@@ -667,7 +664,6 @@
 		compatible = "rockchip,iommu";
 		reg = <0x0 0xff360480 0x0 0x40>, <0x0 0xff3604c0 0x0 0x40>;
 		interrupts = <GIC_SPI 74 IRQ_TYPE_LEVEL_HIGH>;
-		interrupt-names = "rkvdec_mmu";
 		clocks = <&cru ACLK_RKVDEC>, <&cru HCLK_RKVDEC>;
 		clock-names = "aclk", "iface";
 		#iommu-cells = <0>;
@@ -700,7 +696,6 @@
 		compatible = "rockchip,iommu";
 		reg = <0x0 0xff373f00 0x0 0x100>;
 		interrupts = <GIC_SPI 32 IRQ_TYPE_LEVEL_HIGH>;
-		interrupt-names = "vop_mmu";
 		clocks = <&cru ACLK_VOP>, <&cru HCLK_VOP>;
 		clock-names = "aclk", "iface";
 		#iommu-cells = <0>;
@@ -1019,7 +1014,7 @@
 		#size-cells = <2>;
 		ranges;
 
-		gpio0: gpio0@ff210000 {
+		gpio0: gpio@ff210000 {
 			compatible = "rockchip,gpio-bank";
 			reg = <0x0 0xff210000 0x0 0x100>;
 			interrupts = <GIC_SPI 51 IRQ_TYPE_LEVEL_HIGH>;
@@ -1032,7 +1027,7 @@
 			#interrupt-cells = <2>;
 		};
 
-		gpio1: gpio1@ff220000 {
+		gpio1: gpio@ff220000 {
 			compatible = "rockchip,gpio-bank";
 			reg = <0x0 0xff220000 0x0 0x100>;
 			interrupts = <GIC_SPI 52 IRQ_TYPE_LEVEL_HIGH>;
@@ -1045,7 +1040,7 @@
 			#interrupt-cells = <2>;
 		};
 
-		gpio2: gpio2@ff230000 {
+		gpio2: gpio@ff230000 {
 			compatible = "rockchip,gpio-bank";
 			reg = <0x0 0xff230000 0x0 0x100>;
 			interrupts = <GIC_SPI 53 IRQ_TYPE_LEVEL_HIGH>;
@@ -1058,7 +1053,7 @@
 			#interrupt-cells = <2>;
 		};
 
-		gpio3: gpio3@ff240000 {
+		gpio3: gpio@ff240000 {
 			compatible = "rockchip,gpio-bank";
 			reg = <0x0 0xff240000 0x0 0x100>;
 			interrupts = <GIC_SPI 54 IRQ_TYPE_LEVEL_HIGH>;
diff --git a/arch/arm64/boot/dts/rockchip/rk3368-lion.dtsi b/arch/arm64/boot/dts/rockchip/rk3368-lion.dtsi
index bcd7977fb0f8..5753e57fd716 100644
--- a/arch/arm64/boot/dts/rockchip/rk3368-lion.dtsi
+++ b/arch/arm64/boot/dts/rockchip/rk3368-lion.dtsi
@@ -29,15 +29,15 @@
 		i2c-parent = <&i2c1>;
 		mux-gpios = <&gpio1 RK_PA7 GPIO_ACTIVE_HIGH>;
 
-		/* Q7_GPO_I2C */
-		i2c@0 {
+		/* Q7_GP0_I2C */
+		i2c_gp0: i2c@0 {
 			reg = <0>;
 			#address-cells = <1>;
 			#size-cells = <0>;
 		};
 
 		/* Q7_SMB */
-		i2c@1 {
+		i2c_smb: i2c@1 {
 			reg = <1>;
 			#address-cells = <1>;
 			#size-cells = <0>;
@@ -52,7 +52,7 @@
 		mux-gpios = <&gpio1 RK_PB4 GPIO_ACTIVE_HIGH>;
 
 		/* Q7_LVDS_BLC_I2C */
-		i2c@0 {
+		i2c_lvds_blc: i2c@0 {
 			reg = <0>;
 			#address-cells = <1>;
 			#size-cells = <0>;
@@ -69,8 +69,8 @@
 			};
 		};
 
-		/* Q7_GP2_I2C */
-		i2c@1 {
+		/* Q7_GP2_I2C = LVDS_DID_CLK/DAT */
+		i2c_gp2: i2c@1 {
 			reg = <1>;
 			#address-cells = <1>;
 			#size-cells = <0>;
@@ -144,7 +144,7 @@
 	mmc-hs200-1_8v;
 	non-removable;
 	vmmc-supply = <&vcc33_io>;
-	vqmmc-supply = <&vcc18_io>;
+	vqmmc-supply = <&vcc_18>;
 	pinctrl-names = "default";
 	pinctrl-0 = <&emmc_clk>, <&emmc_cmd>, <&emmc_bus8>;
 	status = "okay";
@@ -238,13 +238,6 @@
 				regulator-boot-on;
 			};
 
-			vcc18_io: LDO_REG4 {
-				regulator-name = "vcc18_io";
-				regulator-min-microvolt = <1800000>;
-				regulator-max-microvolt = <1800000>;
-				regulator-boot-on;
-			};
-
 			vdd10_video: LDO_REG6 {
 				regulator-name = "vdd10_video";
 				regulator-min-microvolt = <1000000>;
@@ -253,6 +246,14 @@
 				regulator-boot-on;
 			};
 
+			vcc_18: LDO_REG7 {
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+				regulator-name = "vcc_18";
+			};
+
 			vcc18_video: LDO_REG8 {
 				regulator-name = "vcc18_video";
 				regulator-min-microvolt = <1800000>;
@@ -272,6 +273,18 @@
 	status = "okay";
 };
 
+/* The RK3368-uQ7 "Lion" has most IO voltages hardwired to 3.3V. */
+&io_domains {
+	audio-supply = <&vcc33_io>;
+	dvp-supply = <&vcc33_io>;
+	flash0-supply = <&vcc_18>;
+	gpio30-supply = <&vcc33_io>;
+	gpio1830-supply = <&vcc33_io>;
+	sdcard-supply = <&vcc33_io>;
+	wifi-supply = <&vcc33_io>;
+	status = "okay";
+};
+
 &pinctrl {
 	leds {
 		module_led_pins: module-led-pins {
@@ -291,6 +304,12 @@
 	};
 };
 
+&pmu_io_domains {
+	pmu-supply = <&vcc33_io>;
+	vop-supply = <&vcc33_io>;
+	status = "okay";
+};
+
 &spi1 {
 	status = "okay";
 
diff --git a/arch/arm64/boot/dts/rockchip/rk3368.dtsi b/arch/arm64/boot/dts/rockchip/rk3368.dtsi
index 4c64fbefb483..c99da90328e9 100644
--- a/arch/arm64/boot/dts/rockchip/rk3368.dtsi
+++ b/arch/arm64/boot/dts/rockchip/rk3368.dtsi
@@ -8,6 +8,7 @@
 #include <dt-bindings/interrupt-controller/irq.h>
 #include <dt-bindings/interrupt-controller/arm-gic.h>
 #include <dt-bindings/pinctrl/rockchip.h>
+#include <dt-bindings/power/rk3368-power.h>
 #include <dt-bindings/soc/rockchip,boot-mode.h>
 #include <dt-bindings/thermal/thermal.h>
 
@@ -615,6 +616,115 @@
 		status = "disabled";
 	};
 
+	pmu: power-management@ff730000 {
+		compatible = "rockchip,rk3368-pmu", "syscon", "simple-mfd";
+		reg = <0x0 0xff730000 0x0 0x1000>;
+
+		power: power-controller {
+			compatible = "rockchip,rk3368-power-controller";
+			#power-domain-cells = <1>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			/*
+			 * Note: Although SCLK_* are the working clocks
+			 * of device without including on the NOC, needed for
+			 * synchronous reset.
+			 *
+			 * The clocks on the which NOC:
+			 * ACLK_IEP/ACLK_VIP/ACLK_VOP0 are on ACLK_VIO0_NIU.
+			 * ACLK_ISP/ACLK_VOP1 are on ACLK_VIO1_NIU.
+			 * ACLK_RGA is on ACLK_RGA_NIU.
+			 * The others (HCLK_*,PLCK_*) are on HCLK_VIO_NIU.
+			 *
+			 * Which clock are device clocks:
+			 *	clocks		devices
+			 *	*_IEP		IEP:Image Enhancement Processor
+			 *	*_ISP		ISP:Image Signal Processing
+			 *	*_VIP		VIP:Video Input Processor
+			 *	*_VOP*		VOP:Visual Output Processor
+			 *	*_RGA		RGA
+			 *	*_EDP*		EDP
+			 *	*_DPHY*		LVDS
+			 *	*_HDMI		HDMI
+			 *	*_MIPI_*	MIPI
+			 */
+			power-domain@RK3368_PD_VIO {
+				reg = <RK3368_PD_VIO>;
+				clocks = <&cru ACLK_IEP>,
+					 <&cru ACLK_ISP>,
+					 <&cru ACLK_VIP>,
+					 <&cru ACLK_RGA>,
+					 <&cru ACLK_VOP>,
+					 <&cru ACLK_VOP_IEP>,
+					 <&cru DCLK_VOP>,
+					 <&cru HCLK_IEP>,
+					 <&cru HCLK_ISP>,
+					 <&cru HCLK_RGA>,
+					 <&cru HCLK_VIP>,
+					 <&cru HCLK_VOP>,
+					 <&cru HCLK_VIO_HDCPMMU>,
+					 <&cru PCLK_EDP_CTRL>,
+					 <&cru PCLK_HDMI_CTRL>,
+					 <&cru PCLK_HDCP>,
+					 <&cru PCLK_ISP>,
+					 <&cru PCLK_VIP>,
+					 <&cru PCLK_DPHYRX>,
+					 <&cru PCLK_DPHYTX0>,
+					 <&cru PCLK_MIPI_CSI>,
+					 <&cru PCLK_MIPI_DSI0>,
+					 <&cru SCLK_VOP0_PWM>,
+					 <&cru SCLK_EDP_24M>,
+					 <&cru SCLK_EDP>,
+					 <&cru SCLK_HDCP>,
+					 <&cru SCLK_ISP>,
+					 <&cru SCLK_RGA>,
+					 <&cru SCLK_HDMI_CEC>,
+					 <&cru SCLK_HDMI_HDCP>;
+				pm_qos = <&qos_iep>,
+					 <&qos_isp_r0>,
+					 <&qos_isp_r1>,
+					 <&qos_isp_w0>,
+					 <&qos_isp_w1>,
+					 <&qos_vip>,
+					 <&qos_vop>,
+					 <&qos_rga_r>,
+					 <&qos_rga_w>;
+				#power-domain-cells = <0>;
+			};
+
+			/*
+			 * Note: ACLK_VCODEC/HCLK_VCODEC are VCODEC
+			 * (video endecoder & decoder) clocks that on the
+			 * ACLK_VCODEC_NIU and HCLK_VCODEC_NIU (NOC).
+			 */
+			power-domain@RK3368_PD_VIDEO {
+				reg = <RK3368_PD_VIDEO>;
+				clocks = <&cru ACLK_VIDEO>,
+					 <&cru HCLK_VIDEO>,
+					 <&cru SCLK_HEVC_CABAC>,
+					 <&cru SCLK_HEVC_CORE>;
+				pm_qos = <&qos_hevc_r>,
+					 <&qos_vpu_r>,
+					 <&qos_vpu_w>;
+				#power-domain-cells = <0>;
+			};
+
+			/*
+			 * Note: ACLK_GPU is the GPU clock,
+			 * and on the ACLK_GPU_NIU (NOC).
+			 */
+			power-domain@RK3368_PD_GPU_1 {
+				reg = <RK3368_PD_GPU_1>;
+				clocks = <&cru ACLK_GPU_CFG>,
+					 <&cru ACLK_GPU_MEM>,
+					 <&cru SCLK_GPU_CORE>;
+				pm_qos = <&qos_gpu>;
+				#power-domain-cells = <0>;
+			};
+		};
+	};
+
 	pmugrf: syscon@ff738000 {
 		compatible = "rockchip,rk3368-pmugrf", "syscon", "simple-mfd";
 		reg = <0x0 0xff738000 0x0 0x1000>;
@@ -709,9 +819,9 @@
 		compatible = "rockchip,iommu";
 		reg = <0x0 0xff900800 0x0 0x100>;
 		interrupts = <GIC_SPI 17 IRQ_TYPE_LEVEL_HIGH>;
-		interrupt-names = "iep_mmu";
 		clocks = <&cru ACLK_IEP>, <&cru HCLK_IEP>;
 		clock-names = "aclk", "iface";
+		power-domains = <&power RK3368_PD_VIO>;
 		#iommu-cells = <0>;
 		status = "disabled";
 	};
@@ -721,10 +831,10 @@
 		reg = <0x0 0xff914000 0x0 0x100>,
 		      <0x0 0xff915000 0x0 0x100>;
 		interrupts = <GIC_SPI 14 IRQ_TYPE_LEVEL_HIGH>;
-		interrupt-names = "isp_mmu";
 		clocks = <&cru ACLK_ISP>, <&cru HCLK_ISP>;
 		clock-names = "aclk", "iface";
 		#iommu-cells = <0>;
+		power-domains = <&power RK3368_PD_VIO>;
 		rockchip,disable-mmu-reset;
 		status = "disabled";
 	};
@@ -733,9 +843,9 @@
 		compatible = "rockchip,iommu";
 		reg = <0x0 0xff930300 0x0 0x100>;
 		interrupts = <GIC_SPI 15 IRQ_TYPE_LEVEL_HIGH>;
-		interrupt-names = "vop_mmu";
 		clocks = <&cru ACLK_VOP>, <&cru HCLK_VOP>;
 		clock-names = "aclk", "iface";
+		power-domains = <&power RK3368_PD_VIO>;
 		#iommu-cells = <0>;
 		status = "disabled";
 	};
@@ -745,7 +855,6 @@
 		reg = <0x0 0xff9a0440 0x0 0x40>,
 		      <0x0 0xff9a0480 0x0 0x40>;
 		interrupts = <GIC_SPI 12 IRQ_TYPE_LEVEL_HIGH>;
-		interrupt-names = "hevc_mmu";
 		clocks = <&cru ACLK_VIDEO>, <&cru HCLK_VIDEO>;
 		clock-names = "aclk", "iface";
 		#iommu-cells = <0>;
@@ -757,13 +866,77 @@
 		reg = <0x0 0xff9a0800 0x0 0x100>;
 		interrupts = <GIC_SPI 9 IRQ_TYPE_LEVEL_HIGH>,
 			     <GIC_SPI 10 IRQ_TYPE_LEVEL_HIGH>;
-		interrupt-names = "vepu_mmu", "vdpu_mmu";
 		clocks = <&cru ACLK_VIDEO>, <&cru HCLK_VIDEO>;
 		clock-names = "aclk", "iface";
 		#iommu-cells = <0>;
 		status = "disabled";
 	};
 
+	qos_iep: qos@ffad0000 {
+		compatible = "rockchip,rk3368-qos", "syscon";
+		reg = <0x0 0xffad0000 0x0 0x20>;
+	};
+
+	qos_isp_r0: qos@ffad0080 {
+		compatible = "rockchip,rk3368-qos", "syscon";
+		reg = <0x0 0xffad0080 0x0 0x20>;
+	};
+
+	qos_isp_r1: qos@ffad0100 {
+		compatible = "rockchip,rk3368-qos", "syscon";
+		reg = <0x0 0xffad0100 0x0 0x20>;
+	};
+
+	qos_isp_w0: qos@ffad0180 {
+		compatible = "rockchip,rk3368-qos", "syscon";
+		reg = <0x0 0xffad0180 0x0 0x20>;
+	};
+
+	qos_isp_w1: qos@ffad0200 {
+		compatible = "rockchip,rk3368-qos", "syscon";
+		reg = <0x0 0xffad0200 0x0 0x20>;
+	};
+
+	qos_vip: qos@ffad0280 {
+		compatible = "rockchip,rk3368-qos", "syscon";
+		reg = <0x0 0xffad0280 0x0 0x20>;
+	};
+
+	qos_vop: qos@ffad0300 {
+		compatible = "rockchip,rk3368-qos", "syscon";
+		reg = <0x0 0xffad0300 0x0 0x20>;
+	};
+
+	qos_rga_r: qos@ffad0380 {
+		compatible = "rockchip,rk3368-qos", "syscon";
+		reg = <0x0 0xffad0380 0x0 0x20>;
+	};
+
+	qos_rga_w: qos@ffad0400 {
+		compatible = "rockchip,rk3368-qos", "syscon";
+		reg = <0x0 0xffad0400 0x0 0x20>;
+	};
+
+	qos_hevc_r: qos@ffae0000 {
+		compatible = "rockchip,rk3368-qos", "syscon";
+		reg = <0x0 0xffae0000 0x0 0x20>;
+	};
+
+	qos_vpu_r: qos@ffae0100 {
+		compatible = "rockchip,rk3368-qos", "syscon";
+		reg = <0x0 0xffae0100 0x0 0x20>;
+	};
+
+	qos_vpu_w: qos@ffae0180 {
+		compatible = "rockchip,rk3368-qos", "syscon";
+		reg = <0x0 0xffae0180 0x0 0x20>;
+	};
+
+	qos_gpu: qos@ffaf0000 {
+		compatible = "rockchip,rk3368-qos", "syscon";
+		reg = <0x0 0xffaf0000 0x0 0x20>;
+	};
+
 	efuse256: efuse@ffb00000 {
 		compatible = "rockchip,rk3368-efuse";
 		reg = <0x0 0xffb00000 0x0 0x20>;
@@ -802,7 +975,7 @@
 		#size-cells = <0x2>;
 		ranges;
 
-		gpio0: gpio0@ff750000 {
+		gpio0: gpio@ff750000 {
 			compatible = "rockchip,gpio-bank";
 			reg = <0x0 0xff750000 0x0 0x100>;
 			clocks = <&cru PCLK_GPIO0>;
@@ -815,7 +988,7 @@
 			#interrupt-cells = <0x2>;
 		};
 
-		gpio1: gpio1@ff780000 {
+		gpio1: gpio@ff780000 {
 			compatible = "rockchip,gpio-bank";
 			reg = <0x0 0xff780000 0x0 0x100>;
 			clocks = <&cru PCLK_GPIO1>;
@@ -828,7 +1001,7 @@
 			#interrupt-cells = <0x2>;
 		};
 
-		gpio2: gpio2@ff790000 {
+		gpio2: gpio@ff790000 {
 			compatible = "rockchip,gpio-bank";
 			reg = <0x0 0xff790000 0x0 0x100>;
 			clocks = <&cru PCLK_GPIO2>;
@@ -841,7 +1014,7 @@
 			#interrupt-cells = <0x2>;
 		};
 
-		gpio3: gpio3@ff7a0000 {
+		gpio3: gpio@ff7a0000 {
 			compatible = "rockchip,gpio-bank";
 			reg = <0x0 0xff7a0000 0x0 0x100>;
 			clocks = <&cru PCLK_GPIO3>;
diff --git a/arch/arm64/boot/dts/rockchip/rk3399-gru-bob.dts b/arch/arm64/boot/dts/rockchip/rk3399-gru-bob.dts
index e6c1c94c8d69..31ebb4e5fd33 100644
--- a/arch/arm64/boot/dts/rockchip/rk3399-gru-bob.dts
+++ b/arch/arm64/boot/dts/rockchip/rk3399-gru-bob.dts
@@ -16,6 +16,7 @@
 		     "google,bob-rev7", "google,bob-rev6",
 		     "google,bob-rev5", "google,bob-rev4",
 		     "google,bob", "google,gru", "rockchip,rk3399";
+	chassis-type = "convertible";
 
 	edp_panel: edp-panel {
 		compatible = "boe,nv101wxmn51";
diff --git a/arch/arm64/boot/dts/rockchip/rk3399-gru-chromebook.dtsi b/arch/arm64/boot/dts/rockchip/rk3399-gru-chromebook.dtsi
index 1384dabbdf40..9b2c679f5eca 100644
--- a/arch/arm64/boot/dts/rockchip/rk3399-gru-chromebook.dtsi
+++ b/arch/arm64/boot/dts/rockchip/rk3399-gru-chromebook.dtsi
@@ -251,6 +251,182 @@
 	};
 };
 
+&gpio0 {
+	gpio-line-names = /* GPIO0 A 0-7 */
+			  "AP_RTC_CLK_IN",
+			  "EC_AP_INT_L",
+			  "PP1800_AUDIO_EN",
+			  "BT_HOST_WAKE_L",
+			  "WLAN_MODULE_PD_L",
+			  "H1_INT_OD_L",
+			  "CENTERLOGIC_DVS_PWM",
+			  "",
+
+			  /* GPIO0 B 0-4 */
+			  "WIFI_HOST_WAKE_L",
+			  "PMUIO2_33_18_L",
+			  "PP1500_EN",
+			  "AP_EC_WARM_RESET_REQ",
+			  "PP3000_EN";
+};
+
+&gpio1 {
+	gpio-line-names = /* GPIO1 A 0-7 */
+			  "",
+			  "",
+			  "SPK_PA_EN",
+			  "",
+			  "TRACKPAD_INT_L",
+			  "AP_EC_S3_S0_L",
+			  "AP_EC_OVERTEMP",
+			  "AP_SPI_FLASH_MISO",
+
+			  /* GPIO1 B 0-7 */
+			  "AP_SPI_FLASH_MOSI_R",
+			  "AP_SPI_FLASH_CLK_R",
+			  "AP_SPI_FLASH_CS_L_R",
+			  "WLAN_MODULE_RESET_L",
+			  "WIFI_DISABLE_L",
+			  "MIC_INT",
+			  "",
+			  "AP_I2C_DVS_SDA",
+
+			  /* GPIO1 C 0-7 */
+			  "AP_I2C_DVS_SCL",
+			  "AP_BL_EN",
+			  /*
+			   * AP_FLASH_WP is crossystem ABI. Schematics call it
+			   * AP_FW_WP or CPU1_FW_WP, depending on the variant.
+			   */
+			  "AP_FLASH_WP",
+			  "LITCPU_DVS_PWM",
+			  "AP_I2C_AUDIO_SDA",
+			  "AP_I2C_AUDIO_SCL",
+			  "",
+			  "HEADSET_INT_L";
+};
+
+&gpio2 {
+	gpio-line-names = /* GPIO2 A 0-7 */
+			  "",
+			  "",
+			  "SD_IO_PWR_EN",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "",
+
+			  /* GPIO2 B 0-7 */
+			  "",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "",
+
+			  /* GPIO2 C 0-7 */
+			  "",
+			  "",
+			  "",
+			  "",
+			  "AP_SPI_EC_MISO",
+			  "AP_SPI_EC_MOSI",
+			  "AP_SPI_EC_CLK",
+			  "AP_SPI_EC_CS_L",
+
+			  /* GPIO2 D 0-4 */
+			  "BT_DEV_WAKE_L",
+			  "",
+			  "WIFI_PCIE_CLKREQ_L",
+			  "WIFI_PERST_L",
+			  "SD_PWR_3000_1800_L";
+};
+
+&gpio3 {
+	gpio-line-names = /* GPIO3 A 0-7 */
+			  "",
+			  "",
+			  "",
+			  "",
+			  "AP_SPI_TPM_MISO",
+			  "AP_SPI_TPM_MOSI_R",
+			  "AP_SPI_TPM_CLK_R",
+			  "AP_SPI_TPM_CS_L_R",
+
+			  /* GPIO3 B 0-7 */
+			  "EC_IN_RW",
+			  "",
+			  "AP_I2C_TP_SDA",
+			  "AP_I2C_TP_SCL",
+			  "AP_I2C_TP_PU_EN",
+			  "TOUCH_INT_L",
+			  "",
+			  "",
+
+			  /* GPIO3 C 0-7 */
+			  "",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "",
+
+			  /* GPIO3 D 0-7 */
+			  "I2S0_SCLK",
+			  "I2S0_LRCK_RX",
+			  "I2S0_LRCK_TX",
+			  "I2S0_SDI_0",
+			  "I2S0_SDI_1",
+			  "",
+			  "I2S0_SDO_1",
+			  "I2S0_SDO_0";
+};
+
+&gpio4 {
+	gpio-line-names = /* GPIO4 A 0-7 */
+			  "I2S_MCLK",
+			  "AP_I2C_MIC_SDA",
+			  "AP_I2C_MIC_SCL",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "",
+
+			  /* GPIO4 B 0-7 */
+			  "",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "",
+
+			  /* GPIO4 C 0-7 */
+			  "AP_I2C_TS_SDA",
+			  "AP_I2C_TS_SCL",
+			  "GPU_DVS_PWM",
+			  "UART_DBG_TX_AP_RX",
+			  "UART_AP_TX_DBG_RX",
+			  "",
+			  "BIGCPU_DVS_PWM",
+			  "EDP_HPD_3V0",
+
+			  /* GPIO4 D 0-5 */
+			  "SD_CARD_DET_L",
+			  "USB_DP_HPD",
+			  "TOUCH_RESET_L",
+			  "PP3300_DISP_EN",
+			  "",
+			  "SD_SLOT_PWR_EN";
+};
+
 ap_i2c_mic: &i2c1 {
 	status = "okay";
 
diff --git a/arch/arm64/boot/dts/rockchip/rk3399-gru-kevin.dts b/arch/arm64/boot/dts/rockchip/rk3399-gru-kevin.dts
index 2bbef9fcbe27..6863689df06f 100644
--- a/arch/arm64/boot/dts/rockchip/rk3399-gru-kevin.dts
+++ b/arch/arm64/boot/dts/rockchip/rk3399-gru-kevin.dts
@@ -24,6 +24,7 @@
 		     "google,kevin-rev9", "google,kevin-rev8",
 		     "google,kevin-rev7", "google,kevin-rev6",
 		     "google,kevin", "google,gru", "rockchip,rk3399";
+	chassis-type = "convertible";
 
 	/* Power tree */
 
diff --git a/arch/arm64/boot/dts/rockchip/rk3399-gru-scarlet-dumo.dts b/arch/arm64/boot/dts/rockchip/rk3399-gru-scarlet-dumo.dts
new file mode 100644
index 000000000000..853e88455e75
--- /dev/null
+++ b/arch/arm64/boot/dts/rockchip/rk3399-gru-scarlet-dumo.dts
@@ -0,0 +1,41 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Google Gru-Scarlet Rev5+ (SKU-0) board device tree source
+ *
+ * Copyright 2021 Google LLC.
+ */
+
+/dts-v1/;
+
+#include "rk3399-gru-scarlet.dtsi"
+
+/ {
+	model = "Google Scarlet";
+	compatible = "google,scarlet-rev15-sku0", "google,scarlet-rev15",
+		     "google,scarlet-rev14-sku0", "google,scarlet-rev14",
+		     "google,scarlet-rev13-sku0", "google,scarlet-rev13",
+		     "google,scarlet-rev12-sku0", "google,scarlet-rev12",
+		     "google,scarlet-rev11-sku0", "google,scarlet-rev11",
+		     "google,scarlet-rev10-sku0", "google,scarlet-rev10",
+		     "google,scarlet-rev9-sku0",  "google,scarlet-rev9",
+		     "google,scarlet-rev8-sku0",  "google,scarlet-rev8",
+		     "google,scarlet-rev7-sku0",  "google,scarlet-rev7",
+		     "google,scarlet-rev6-sku0",  "google,scarlet-rev6",
+		     "google,scarlet-rev5-sku0",  "google,scarlet-rev5",
+		     "google,scarlet", "google,gru", "rockchip,rk3399";
+};
+
+&mipi_panel {
+	compatible = "innolux,p097pfg";
+	avdd-supply = <&ppvarp_lcd>;
+	avee-supply = <&ppvarn_lcd>;
+};
+
+&pci_rootport {
+	wifi@0,0 {
+		compatible = "qcom,ath10k";
+		reg = <0x00010000 0x0 0x00000000 0x0 0x00000000>,
+		      <0x03010010 0x0 0x00000000 0x0 0x00200000>;
+		qcom,ath10k-calibration-variant = "GO_DUMO";
+	};
+};
diff --git a/arch/arm64/boot/dts/rockchip/rk3399-gru-scarlet.dtsi b/arch/arm64/boot/dts/rockchip/rk3399-gru-scarlet.dtsi
index 5d7a9d96d163..a9817b3d7edc 100644
--- a/arch/arm64/boot/dts/rockchip/rk3399-gru-scarlet.dtsi
+++ b/arch/arm64/boot/dts/rockchip/rk3399-gru-scarlet.dtsi
@@ -8,6 +8,8 @@
 #include "rk3399-gru.dtsi"
 
 /{
+	chassis-type = "tablet";
+
 	/* Power tree */
 
 	/* ppvar_sys children, sorted by name */
@@ -389,6 +391,186 @@ camera: &i2c7 {
 		<400000000>;
 };
 
+&gpio0 {
+	gpio-line-names = /* GPIO0 A 0-7 */
+			  "CLK_32K_AP",
+			  "EC_IN_RW_OD",
+			  "SPK_PA_EN",
+			  "WLAN_PERST_1V8_L",
+			  "WLAN_PD_1V8_L",
+			  "WLAN_RF_KILL_1V8_L",
+			  "BIGCPU_DVS_PWM",
+			  "SD_CD_L_JTAG_EN",
+
+			  /* GPIO0 B 0-5 */
+			  "BT_EN_BT_RF_KILL_1V8_L",
+			  "PMUIO2_33_18_L_PP3300_S0_EN",
+			  "TOUCH_RESET_L",
+			  "AP_EC_WARM_RESET_REQ",
+			  "PEN_RESET_L",
+			  /*
+			   * AP_FLASH_WP_L is crossystem ABI. Schematics call
+			   * it AP_FLASH_WP_R_ODL.
+			   */
+			  "AP_FLASH_WP_L";
+};
+
+&gpio1 {
+	gpio-line-names = /* GPIO1 A 0-7 */
+			  "PEN_INT_ODL",
+			  "PEN_EJECT_ODL",
+			  "BT_HOST_WAKE_1V8_L",
+			  "WLAN_HOST_WAKE_1V8_L",
+			  "TOUCH_INT_ODL",
+			  "AP_EC_S3_S0_L",
+			  "AP_EC_OVERTEMP",
+			  "AP_SPI_FLASH_MISO",
+
+			  /* GPIO1 B 0-7 */
+			  "AP_SPI_FLASH_MOSI_R",
+			  "AP_SPI_FLASH_CLK_R",
+			  "AP_SPI_FLASH_CS_L_R",
+			  "SD_CARD_DET_ODL",
+			  "",
+			  "AP_EXPANSION_IO1",
+			  "AP_EXPANSION_IO2",
+			  "AP_I2C_DISP_SDA",
+
+			  /* GPIO1 C 0-7 */
+			  "AP_I2C_DISP_SCL",
+			  "H1_INT_ODL",
+			  "EC_AP_INT_ODL",
+			  "LITCPU_DVS_PWM",
+			  "AP_I2C_AUDIO_SDA",
+			  "AP_I2C_AUDIO_SCL",
+			  "AP_EXPANSION_IO3",
+			  "HEADSET_INT_ODL",
+
+			  /* GPIO1 D0 */
+			  "AP_EXPANSION_IO4";
+};
+
+&gpio2 {
+	gpio-line-names = /* GPIO2 A 0-7 */
+			  "AP_I2C_PEN_SDA",
+			  "AP_I2C_PEN_SCL",
+			  "SD_IO_PWR_EN",
+			  "UCAM_RST_L",
+			  "PP1250_CAM_EN",
+			  "WCAM_RST_L",
+			  "AP_EXPANSION_IO5",
+			  "AP_I2C_CAM_SDA",
+
+			  /* GPIO2 B 0-7 */
+			  "AP_I2C_CAM_SCL",
+			  "AP_H1_SPI_MISO",
+			  "AP_H1_SPI_MOSI",
+			  "AP_H1_SPI_CLK",
+			  "AP_H1_SPI_CS_L",
+			  "",
+			  "",
+			  "",
+
+			  /* GPIO2 C 0-7 */
+			  "UART_EXPANSION_TX_AP_RX",
+			  "UART_AP_TX_EXPANSION_RX",
+			  "UART_EXPANSION_RTS_AP_CTS",
+			  "UART_AP_RTS_EXPANSION_CTS",
+			  "AP_SPI_EC_MISO",
+			  "AP_SPI_EC_MOSI",
+			  "AP_SPI_EC_CLK",
+			  "AP_SPI_EC_CS_L",
+
+			  /* GPIO2 D 0-4 */
+			  "PP2800_CAM_EN",
+			  "CLK_24M_CAM",
+			  "WLAN_PCIE_CLKREQ_1V8_L",
+			  "",
+			  "SD_PWR_3000_1800_L";
+};
+
+&gpio3 {
+	gpio-line-names = /* GPIO3 A 0-7 */
+			  "",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "",
+
+			  /* GPIO3 B 0-7 */
+			  "",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "",
+
+			  /* GPIO3 C 0-7 */
+			  "",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "",
+
+			  /* GPIO3 D 0-7 */
+			  "I2S0_SCLK",
+			  "I2S0_LRCK_RX",
+			  "I2S0_LRCK_TX",
+			  "I2S0_SDI_0",
+			  "STRAP_LCDBIAS_L",
+			  "STRAP_FEATURE_1",
+			  "STRAP_FEATURE_2",
+			  "I2S0_SDO_0";
+};
+
+&gpio4 {
+	gpio-line-names = /* GPIO4 A 0-7 */
+			  "I2S_MCLK",
+			  "AP_I2C_EXPANSION_SDA",
+			  "AP_I2C_EXPANSION_SCL",
+			  "DMIC_EN",
+			  "",
+			  "",
+			  "",
+			  "",
+
+			  /* GPIO4 B 0-7 */
+			  "",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "",
+
+			  /* GPIO4 C 0-7 */
+			  "AP_I2C_TS_SDA",
+			  "AP_I2C_TS_SCL",
+			  "GPU_DVS_PWM",
+			  "UART_DBG_TX_AP_RX",
+			  "UART_AP_TX_DBG_RX",
+			  "BL_EN",
+			  "BL_PWM",
+			  "",
+
+			  /* GPIO4 D 0-5 */
+			  "",
+			  "DISPLAY_RST_L",
+			  "",
+			  "PPVARP_LCD_EN",
+			  "PPVARN_LCD_EN",
+			  "SD_SLOT_PWR_EN";
+};
+
 &i2c_tunnel {
 	google,remote-bus = <0>;
 };
diff --git a/arch/arm64/boot/dts/rockchip/rk3399-gru.dtsi b/arch/arm64/boot/dts/rockchip/rk3399-gru.dtsi
index c1bcc8ca3769..45a5ae5d2027 100644
--- a/arch/arm64/boot/dts/rockchip/rk3399-gru.dtsi
+++ b/arch/arm64/boot/dts/rockchip/rk3399-gru.dtsi
@@ -461,7 +461,7 @@ ap_i2c_audio: &i2c8 {
 	vpcie0v9-supply = <&pp900_pcie>;
 
 	pci_rootport: pcie@0,0 {
-		reg = <0x83000000 0x0 0x00000000 0x0 0x00000000>;
+		reg = <0x0000 0 0 0 0>;
 		#address-cells = <3>;
 		#size-cells = <2>;
 		ranges;
@@ -543,7 +543,7 @@ ap_i2c_audio: &i2c8 {
 	pinctrl-names = "default", "sleep";
 	pinctrl-1 = <&spi1_sleep>;
 
-	spiflash@0 {
+	flash@0 {
 		compatible = "jedec,spi-nor";
 		reg = <0>;
 
diff --git a/arch/arm64/boot/dts/rockchip/rk3399-kobol-helios64.dts b/arch/arm64/boot/dts/rockchip/rk3399-kobol-helios64.dts
index 738cfd21df3e..63c7681843da 100644
--- a/arch/arm64/boot/dts/rockchip/rk3399-kobol-helios64.dts
+++ b/arch/arm64/boot/dts/rockchip/rk3399-kobol-helios64.dts
@@ -21,6 +21,9 @@
 	aliases {
 		mmc0 = &sdmmc;
 		mmc1 = &sdhci;
+		spi1 = &spi1;
+		spi2 = &spi2;
+		spi5 = &spi5;
 	};
 
 	avdd_0v9_s0: avdd-0v9-s0 {
@@ -43,6 +46,10 @@
 		vin-supply = <&vcc3v3_sys_s3>;
 	};
 
+	chosen {
+		stdout-path = "serial2:1500000n8";
+	};
+
 	clkin_gmac: external-gmac-clock {
 		compatible = "fixed-clock";
 		clock-frequency = <125000000>;
@@ -469,11 +476,40 @@
 	status = "okay";
 };
 
+&spi1 {
+	status = "okay";
+
+	spiflash: flash@0 {
+		compatible = "jedec,spi-nor";
+		reg = <0x0>;
+		spi-max-frequency = <25000000>;
+		status = "okay";
+		m25p,fast-read;
+	};
+};
+
+/* UEXT connector */
+&spi2 {
+	status = "okay";
+};
+
+&spi5 {
+	status = "okay";
+};
+
 &tcphy1 {
 	/* phy for &usbdrd_dwc3_1 */
 	status = "okay";
 };
 
+&tsadc {
+	/* tshut mode 0:CRU 1:GPIO */
+	rockchip,hw-tshut-mode = <1>;
+	/* tshut polarity 0:LOW 1:HIGH */
+	rockchip,hw-tshut-polarity = <1>;
+	status = "okay";
+};
+
 &u2phy1 {
 	status = "okay";
 
diff --git a/arch/arm64/boot/dts/rockchip/rk3399-op1-opp.dtsi b/arch/arm64/boot/dts/rockchip/rk3399-op1-opp.dtsi
index 69cc9b05baa5..2180e0f75003 100644
--- a/arch/arm64/boot/dts/rockchip/rk3399-op1-opp.dtsi
+++ b/arch/arm64/boot/dts/rockchip/rk3399-op1-opp.dtsi
@@ -4,7 +4,7 @@
  */
 
 / {
-	cluster0_opp: opp-table0 {
+	cluster0_opp: opp-table-0 {
 		compatible = "operating-points-v2";
 		opp-shared;
 
@@ -39,7 +39,7 @@
 		};
 	};
 
-	cluster1_opp: opp-table1 {
+	cluster1_opp: opp-table-1 {
 		compatible = "operating-points-v2";
 		opp-shared;
 
@@ -82,7 +82,7 @@
 		};
 	};
 
-	gpu_opp_table: opp-table2 {
+	gpu_opp_table: opp-table-2 {
 		compatible = "operating-points-v2";
 
 		opp00 {
diff --git a/arch/arm64/boot/dts/rockchip/rk3399-opp.dtsi b/arch/arm64/boot/dts/rockchip/rk3399-opp.dtsi
index da41cd81ebb7..fee5e7111279 100644
--- a/arch/arm64/boot/dts/rockchip/rk3399-opp.dtsi
+++ b/arch/arm64/boot/dts/rockchip/rk3399-opp.dtsi
@@ -4,7 +4,7 @@
  */
 
 / {
-	cluster0_opp: opp-table0 {
+	cluster0_opp: opp-table-0 {
 		compatible = "operating-points-v2";
 		opp-shared;
 
@@ -35,7 +35,7 @@
 		};
 	};
 
-	cluster1_opp: opp-table1 {
+	cluster1_opp: opp-table-1 {
 		compatible = "operating-points-v2";
 		opp-shared;
 
@@ -74,7 +74,7 @@
 		};
 	};
 
-	gpu_opp_table: opp-table2 {
+	gpu_opp_table: opp-table-2 {
 		compatible = "operating-points-v2";
 
 		opp00 {
diff --git a/arch/arm64/boot/dts/rockchip/rk3399-pinebook-pro.dts b/arch/arm64/boot/dts/rockchip/rk3399-pinebook-pro.dts
index 2b5f001ff4a6..c2f021a1a18f 100644
--- a/arch/arm64/boot/dts/rockchip/rk3399-pinebook-pro.dts
+++ b/arch/arm64/boot/dts/rockchip/rk3399-pinebook-pro.dts
@@ -17,6 +17,7 @@
 / {
 	model = "Pine64 Pinebook Pro";
 	compatible = "pine64,pinebook-pro", "rockchip,rk3399";
+	chassis-type = "laptop";
 
 	aliases {
 		mmc0 = &sdio0;
@@ -385,10 +386,6 @@
 	};
 };
 
-&cdn_dp {
-	status = "okay";
-};
-
 &cpu_b0 {
 	cpu-supply = <&vdd_cpu_b>;
 };
@@ -711,7 +708,7 @@
 
 		connector {
 			compatible = "usb-c-connector";
-			data-role = "host";
+			data-role = "dual";
 			label = "USB-C";
 			op-sink-microwatt = <1000000>;
 			power-role = "dual";
diff --git a/arch/arm64/boot/dts/rockchip/rk3399-roc-pc-plus.dts b/arch/arm64/boot/dts/rockchip/rk3399-roc-pc-plus.dts
new file mode 100644
index 000000000000..5a2661ae0131
--- /dev/null
+++ b/arch/arm64/boot/dts/rockchip/rk3399-roc-pc-plus.dts
@@ -0,0 +1,218 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright (c) 2017 T-Chip Intelligent Technology Co., Ltd
+ */
+
+/dts-v1/;
+#include "rk3399-roc-pc.dtsi"
+
+/*
+ * Notice:
+ * 1. rk3399-roc-pc-plus is powered by dc_12v directly.
+ * 2. rk3399-roc-pc-plus has only vcc_bus_typec0 in schematic, which is coresponding
+ *    to vcc_vbus_typec1 in rk3399-roc-pc.
+ *    For simplicity, reserve the node name of vcc_vbus_typec1.
+ * 3. vcc5v0_host is actually 2 regulators (host0, 1) controlled by the same gpio.
+ */
+
+/delete-node/ &fusb1;
+/delete-node/ &hub_rst;
+/delete-node/ &mp8859;
+/delete-node/ &vcc_sys_en;
+/delete-node/ &vcc_vbus_typec0;
+/delete-node/ &yellow_led;
+
+/ {
+	model = "Firefly ROC-RK3399-PC-PLUS Board";
+	compatible = "firefly,roc-rk3399-pc-plus", "rockchip,rk3399";
+
+	dc_12v: dc-12v {
+		compatible = "regulator-fixed";
+		regulator-name = "dc_12v";
+		regulator-always-on;
+		regulator-boot-on;
+		regulator-min-microvolt = <12000000>;
+		regulator-max-microvolt = <12000000>;
+	};
+
+	es8388-sound {
+		compatible = "simple-audio-card";
+		pinctrl-names = "default";
+		pinctrl-0 = <&hp_det_pin>;
+		simple-audio-card,name = "rockchip,es8388-codec";
+		simple-audio-card,format = "i2s";
+		simple-audio-card,mclk-fs = <256>;
+		simple-audio-card,widgets =
+			"Microphone", "Mic Jack",
+			"Headphone", "Headphones";
+		simple-audio-card,routing =
+			"LINPUT1", "Mic Jack",
+			"Headphone Amp INL", "LOUT2",
+			"Headphone Amp INR", "ROUT2",
+			"Headphones", "Headphone Amp OUTL",
+			"Headphones", "Headphone Amp OUTR";
+		simple-audio-card,hp-det-gpio = <&gpio2 RK_PA6 GPIO_ACTIVE_HIGH>;
+		simple-audio-card,aux-devs = <&headphones_amp>;
+		simple-audio-card,pin-switches = "Headphones";
+
+		simple-audio-card,codec {
+			sound-dai = <&es8388>;
+		};
+
+		simple-audio-card,cpu {
+			sound-dai = <&i2s1>;
+		};
+	};
+
+	gpio-fan {
+		#cooling-cells = <2>;
+		compatible = "gpio-fan";
+		gpio-fan,speed-map = <0 0 3000 1>;
+		gpios = <&gpio1 RK_PA1 GPIO_ACTIVE_HIGH>;
+	};
+
+	/delete-node/ gpio-keys;
+
+	/* not amplifier, used as switcher only */
+	headphones_amp: headphones-amp {
+		compatible = "simple-audio-amplifier";
+		pinctrl-names = "default";
+		pinctrl-0 = <&ear_ctl_pin>;
+		enable-gpios = <&gpio0 RK_PA2 GPIO_ACTIVE_HIGH>;
+		sound-name-prefix = "Headphone Amp";
+		VCC-supply = <&vcca3v0_codec>;
+	};
+
+	ir-receiver {
+		linux,rc-map-name = "rc-khadas";
+	};
+
+	leds {
+		pinctrl-names = "default";
+		pinctrl-0 = <&work_led_pin>, <&diy_led_pin>;
+	};
+};
+
+&fusb0 {
+	vbus-supply = <&vcc_vbus_typec1>;
+};
+
+&i2c0 {
+	hym8563: hym8563@51 {
+		compatible = "haoyu,hym8563";
+		reg = <0x51>;
+		interrupt-parent = <&gpio0>;
+		interrupts = <RK_PA5 IRQ_TYPE_EDGE_FALLING>;
+		#clock-cells = <0>;
+		clock-frequency = <32768>;
+		clock-output-names = "xin32k";
+		pinctrl-names = "default";
+		pinctrl-0 = <&hym8563_int>;
+	};
+};
+
+&i2c1 {
+	es8388: es8388@11 {
+		compatible = "everest,es8388";
+		reg = <0x11>;
+		clock-names = "mclk";
+		clocks = <&cru SCLK_I2S_8CH_OUT>;
+		#sound-dai-cells = <0>;
+	};
+};
+
+/* <4 RK_PA0 1 &pcfg_pull_none> is used as i2s_8ch_mclk_pin */
+&i2s0_8ch_bus {
+	rockchip,pins =
+		<3 RK_PD0 1 &pcfg_pull_none>,
+		<3 RK_PD1 1 &pcfg_pull_none>,
+		<3 RK_PD2 1 &pcfg_pull_none>,
+		<3 RK_PD3 1 &pcfg_pull_none>,
+		<3 RK_PD4 1 &pcfg_pull_none>,
+		<3 RK_PD5 1 &pcfg_pull_none>,
+		<3 RK_PD6 1 &pcfg_pull_none>,
+		<3 RK_PD7 1 &pcfg_pull_none>;
+};
+
+&i2s1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2s_8ch_mclk_pin>, <&i2s1_2ch_bus>;
+	rockchip,playback-channels = <2>;
+	rockchip,capture-channels = <2>;
+	status = "okay";
+};
+
+&pinctrl {
+	es8388 {
+		ear_ctl_pin: ear-ctl-pin {
+			rockchip,pins = <0 RK_PA2 RK_FUNC_GPIO &pcfg_output_high>;
+		};
+
+		hp_det_pin: hp-det-pin {
+			rockchip,pins = <2 RK_PA6 RK_FUNC_GPIO &pcfg_pull_down>;
+		};
+	};
+
+	hym8563 {
+		hym8563_int: hym8563-int {
+			rockchip,pins = <0 RK_PA5 RK_FUNC_GPIO &pcfg_pull_up>;
+		};
+	};
+
+	i2s1 {
+		i2s_8ch_mclk_pin: i2s-8ch-mclk-pin {
+			rockchip,pins = <4 RK_PA0 1 &pcfg_pull_none>;
+		};
+	};
+};
+
+&u2phy0 {
+	status = "okay";
+
+	u2phy0_otg: otg-port {
+		phy-supply = <&vcc_vbus_typec1>;
+		status = "okay";
+	};
+
+	u2phy0_host: host-port {
+		phy-supply = <&vcc5v0_host>;
+		status = "okay";
+	};
+};
+
+&u2phy1 {
+	status = "okay";
+
+	u2phy1_otg: otg-port {
+		phy-supply = <&vcc5v0_host>;
+		status = "okay";
+	};
+
+	u2phy1_host: host-port {
+		phy-supply = <&vcc5v0_host>;
+		status = "okay";
+	};
+};
+
+&uart0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart0_xfer &uart0_cts &uart0_rts>;
+	status = "okay";
+};
+
+&usbdrd_dwc3_0 {
+	dr_mode = "host";
+	status = "okay";
+};
+
+&vcc_sys {
+	/* vcc_sys is fixed, not controlled by any gpio */
+	/delete-property/ gpio;
+	/delete-property/ pinctrl-names;
+	/delete-property/ pinctrl-0;
+};
+
+&vcc5v0_host {
+	pinctrl-names = "default";
+	pinctrl-0 = <&vcc5v0_host_en>;
+};
diff --git a/arch/arm64/boot/dts/rockchip/rk3399-rock-pi-4.dtsi b/arch/arm64/boot/dts/rockchip/rk3399-rock-pi-4.dtsi
index b28888ea9262..98136c88fa49 100644
--- a/arch/arm64/boot/dts/rockchip/rk3399-rock-pi-4.dtsi
+++ b/arch/arm64/boot/dts/rockchip/rk3399-rock-pi-4.dtsi
@@ -36,6 +36,29 @@
 		reset-gpios = <&gpio0 RK_PB2 GPIO_ACTIVE_LOW>;
 	};
 
+	sound {
+		compatible = "audio-graph-card";
+		label = "Analog";
+		dais = <&i2s0_p0>;
+	};
+
+	sound-dit {
+		compatible = "audio-graph-card";
+		label = "SPDIF";
+		dais = <&spdif_p0>;
+	};
+
+	spdif-dit {
+		compatible = "linux,spdif-dit";
+		#sound-dai-cells = <0>;
+
+		port {
+			dit_p0_0: endpoint {
+				remote-endpoint = <&spdif_p0_0>;
+			};
+		};
+	};
+
 	vcc12v_dcin: dc-12v {
 		compatible = "regulator-fixed";
 		regulator-name = "vcc12v_dcin";
@@ -422,6 +445,20 @@
 	i2c-scl-rising-time-ns = <300>;
 	i2c-scl-falling-time-ns = <15>;
 	status = "okay";
+
+	es8316: codec@11 {
+		compatible = "everest,es8316";
+		reg = <0x11>;
+		clocks = <&cru SCLK_I2S_8CH_OUT>;
+		clock-names = "mclk";
+		#sound-dai-cells = <0>;
+
+		port {
+			es8316_p0_0: endpoint {
+				remote-endpoint = <&i2s0_p0_0>;
+			};
+		};
+	};
 };
 
 &i2c3 {
@@ -441,6 +478,14 @@
 	rockchip,capture-channels = <2>;
 	rockchip,playback-channels = <2>;
 	status = "okay";
+
+	i2s0_p0: port {
+		i2s0_p0_0: endpoint {
+			dai-format = "i2s";
+			mclk-fs = <256>;
+			remote-endpoint = <&es8316_p0_0>;
+		};
+	};
 };
 
 &i2s1 {
@@ -603,6 +648,15 @@
 	status = "okay";
 };
 
+&spdif {
+
+	spdif_p0: port {
+		spdif_p0_0: endpoint {
+			remote-endpoint = <&dit_p0_0>;
+		};
+	};
+};
+
 &tcphy0 {
 	status = "okay";
 };
diff --git a/arch/arm64/boot/dts/rockchip/rk3399-rock-pi-4a-plus.dts b/arch/arm64/boot/dts/rockchip/rk3399-rock-pi-4a-plus.dts
new file mode 100644
index 000000000000..281a04b2f5e9
--- /dev/null
+++ b/arch/arm64/boot/dts/rockchip/rk3399-rock-pi-4a-plus.dts
@@ -0,0 +1,14 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright (c) 2019 Akash Gajjar <Akash_Gajjar@mentor.com>
+ * Copyright (c) 2019 Pragnesh Patel <Pragnesh_Patel@mentor.com>
+ */
+
+/dts-v1/;
+#include "rk3399-rock-pi-4.dtsi"
+#include "rk3399-op1-opp.dtsi"
+
+/ {
+	model = "Radxa ROCK Pi 4A+";
+	compatible = "radxa,rockpi4a-plus", "radxa,rockpi4", "rockchip,rk3399";
+};
diff --git a/arch/arm64/boot/dts/rockchip/rk3399-rock-pi-4b-plus.dts b/arch/arm64/boot/dts/rockchip/rk3399-rock-pi-4b-plus.dts
new file mode 100644
index 000000000000..dfad13d2ab24
--- /dev/null
+++ b/arch/arm64/boot/dts/rockchip/rk3399-rock-pi-4b-plus.dts
@@ -0,0 +1,47 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright (c) 2019 Akash Gajjar <Akash_Gajjar@mentor.com>
+ * Copyright (c) 2019 Pragnesh Patel <Pragnesh_Patel@mentor.com>
+ */
+
+/dts-v1/;
+#include "rk3399-rock-pi-4.dtsi"
+#include "rk3399-op1-opp.dtsi"
+
+/ {
+	model = "Radxa ROCK Pi 4B+";
+	compatible = "radxa,rockpi4b-plus", "radxa,rockpi4", "rockchip,rk3399";
+
+	aliases {
+		mmc2 = &sdio0;
+	};
+};
+
+&sdio0 {
+	status = "okay";
+
+	brcmf: wifi@1 {
+		compatible = "brcm,bcm4329-fmac";
+		reg = <1>;
+		interrupt-parent = <&gpio0>;
+		interrupts = <RK_PA3 GPIO_ACTIVE_HIGH>;
+		interrupt-names = "host-wake";
+		pinctrl-names = "default";
+		pinctrl-0 = <&wifi_host_wake_l>;
+	};
+};
+
+&uart0 {
+	status = "okay";
+
+	bluetooth {
+		compatible = "brcm,bcm43438-bt";
+		clocks = <&rk808 1>;
+		clock-names = "ext_clock";
+		device-wakeup-gpios = <&gpio2 RK_PD3 GPIO_ACTIVE_HIGH>;
+		host-wakeup-gpios = <&gpio0 RK_PA4 GPIO_ACTIVE_HIGH>;
+		shutdown-gpios = <&gpio0 RK_PB1 GPIO_ACTIVE_HIGH>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&bt_host_wake_l &bt_wake_l &bt_enable_h>;
+	};
+};
diff --git a/arch/arm64/boot/dts/rockchip/rk3399-rockpro64.dtsi b/arch/arm64/boot/dts/rockchip/rk3399-rockpro64.dtsi
index 6bff8db7d33e..83db4ca67334 100644
--- a/arch/arm64/boot/dts/rockchip/rk3399-rockpro64.dtsi
+++ b/arch/arm64/boot/dts/rockchip/rk3399-rockpro64.dtsi
@@ -69,6 +69,7 @@
 
 	fan: pwm-fan {
 		compatible = "pwm-fan";
+		cooling-levels = <0 100 150 200 255>;
 		#cooling-cells = <2>;
 		fan-supply = <&vcc12v_dcin>;
 		pwms = <&pwm1 0 50000 0>;
@@ -245,6 +246,34 @@
 	cpu-supply = <&vdd_cpu_b>;
 };
 
+&cpu_thermal {
+	trips {
+		cpu_warm: cpu_warm {
+			temperature = <55000>;
+			hysteresis = <2000>;
+			type = "active";
+		};
+
+		cpu_hot: cpu_hot {
+			temperature = <65000>;
+			hysteresis = <2000>;
+			type = "active";
+		};
+	};
+
+	cooling-maps {
+		map2 {
+			trip = <&cpu_warm>;
+			cooling-device = <&fan THERMAL_NO_LIMIT 1>;
+		};
+
+		map3 {
+			trip = <&cpu_hot>;
+			cooling-device = <&fan 2 THERMAL_NO_LIMIT>;
+		};
+	};
+};
+
 &emmc_phy {
 	status = "okay";
 };
diff --git a/arch/arm64/boot/dts/rockchip/rk3399.dtsi b/arch/arm64/boot/dts/rockchip/rk3399.dtsi
index 3871c7fd83b0..d3cdf6f42a30 100644
--- a/arch/arm64/boot/dts/rockchip/rk3399.dtsi
+++ b/arch/arm64/boot/dts/rockchip/rk3399.dtsi
@@ -124,6 +124,12 @@
 			#cooling-cells = <2>; /* min followed by max */
 			dynamic-power-coefficient = <436>;
 			cpu-idle-states = <&CPU_SLEEP &CLUSTER_SLEEP>;
+
+			thermal-idle {
+				#cooling-cells = <2>;
+				duration-us = <10000>;
+				exit-latency-us = <500>;
+			};
 		};
 
 		cpu_b1: cpu@101 {
@@ -136,6 +142,12 @@
 			#cooling-cells = <2>; /* min followed by max */
 			dynamic-power-coefficient = <436>;
 			cpu-idle-states = <&CPU_SLEEP &CLUSTER_SLEEP>;
+
+			thermal-idle {
+				#cooling-cells = <2>;
+				duration-us = <10000>;
+				exit-latency-us = <500>;
+			};
 		};
 
 		idle-states {
@@ -361,6 +373,54 @@
 		status = "disabled";
 	};
 
+	debug@fe430000 {
+		compatible = "arm,coresight-cpu-debug", "arm,primecell";
+		reg = <0 0xfe430000 0 0x1000>;
+		clocks = <&cru PCLK_COREDBG_L>;
+		clock-names = "apb_pclk";
+		cpu = <&cpu_l0>;
+	};
+
+	debug@fe432000 {
+		compatible = "arm,coresight-cpu-debug", "arm,primecell";
+		reg = <0 0xfe432000 0 0x1000>;
+		clocks = <&cru PCLK_COREDBG_L>;
+		clock-names = "apb_pclk";
+		cpu = <&cpu_l1>;
+	};
+
+	debug@fe434000 {
+		compatible = "arm,coresight-cpu-debug", "arm,primecell";
+		reg = <0 0xfe434000 0 0x1000>;
+		clocks = <&cru PCLK_COREDBG_L>;
+		clock-names = "apb_pclk";
+		cpu = <&cpu_l2>;
+	};
+
+	debug@fe436000 {
+		compatible = "arm,coresight-cpu-debug", "arm,primecell";
+		reg = <0 0xfe436000 0 0x1000>;
+		clocks = <&cru PCLK_COREDBG_L>;
+		clock-names = "apb_pclk";
+		cpu = <&cpu_l3>;
+	};
+
+	debug@fe610000 {
+		compatible = "arm,coresight-cpu-debug", "arm,primecell";
+		reg = <0 0xfe610000 0 0x1000>;
+		clocks = <&cru PCLK_COREDBG_B>;
+		clock-names = "apb_pclk";
+		cpu = <&cpu_b0>;
+	};
+
+	debug@fe710000 {
+		compatible = "arm,coresight-cpu-debug", "arm,primecell";
+		reg = <0 0xfe710000 0 0x1000>;
+		clocks = <&cru PCLK_COREDBG_B>;
+		clock-names = "apb_pclk";
+		cpu = <&cpu_b1>;
+	};
+
 	usbdrd3_0: usb@fe800000 {
 		compatible = "rockchip,rk3399-dwc3";
 		#address-cells = <2>;
@@ -1251,7 +1311,6 @@
 		compatible = "rockchip,iommu";
 		reg = <0x0 0xff650800 0x0 0x40>;
 		interrupts = <GIC_SPI 115 IRQ_TYPE_LEVEL_HIGH 0>;
-		interrupt-names = "vpu_mmu";
 		clocks = <&cru ACLK_VCODEC>, <&cru HCLK_VCODEC>;
 		clock-names = "aclk", "iface";
 		#iommu-cells = <0>;
@@ -1273,7 +1332,6 @@
 		compatible = "rockchip,iommu";
 		reg = <0x0 0xff660480 0x0 0x40>, <0x0 0xff6604c0 0x0 0x40>;
 		interrupts = <GIC_SPI 117 IRQ_TYPE_LEVEL_HIGH 0>;
-		interrupt-names = "vdec_mmu";
 		clocks = <&cru ACLK_VDU>, <&cru HCLK_VDU>;
 		clock-names = "aclk", "iface";
 		power-domains = <&power RK3399_PD_VDU>;
@@ -1284,7 +1342,6 @@
 		compatible = "rockchip,iommu";
 		reg = <0x0 0xff670800 0x0 0x40>;
 		interrupts = <GIC_SPI 42 IRQ_TYPE_LEVEL_HIGH 0>;
-		interrupt-names = "iep_mmu";
 		clocks = <&cru ACLK_IEP>, <&cru HCLK_IEP>;
 		clock-names = "aclk", "iface";
 		#iommu-cells = <0>;
@@ -1666,7 +1723,6 @@
 		compatible = "rockchip,iommu";
 		reg = <0x0 0xff8f3f00 0x0 0x100>;
 		interrupts = <GIC_SPI 119 IRQ_TYPE_LEVEL_HIGH 0>;
-		interrupt-names = "vopl_mmu";
 		clocks = <&cru ACLK_VOP1>, <&cru HCLK_VOP1>;
 		clock-names = "aclk", "iface";
 		power-domains = <&power RK3399_PD_VOPL>;
@@ -1723,7 +1779,6 @@
 		compatible = "rockchip,iommu";
 		reg = <0x0 0xff903f00 0x0 0x100>;
 		interrupts = <GIC_SPI 118 IRQ_TYPE_LEVEL_HIGH 0>;
-		interrupt-names = "vopb_mmu";
 		clocks = <&cru ACLK_VOP0>, <&cru HCLK_VOP0>;
 		clock-names = "aclk", "iface";
 		power-domains = <&power RK3399_PD_VOPB>;
@@ -1761,7 +1816,6 @@
 		compatible = "rockchip,iommu";
 		reg = <0x0 0xff914000 0x0 0x100>, <0x0 0xff915000 0x0 0x100>;
 		interrupts = <GIC_SPI 43 IRQ_TYPE_LEVEL_HIGH 0>;
-		interrupt-names = "isp0_mmu";
 		clocks = <&cru ACLK_ISP0_WRAPPER>, <&cru HCLK_ISP0_WRAPPER>;
 		clock-names = "aclk", "iface";
 		#iommu-cells = <0>;
@@ -1769,11 +1823,36 @@
 		rockchip,disable-mmu-reset;
 	};
 
+	isp1: isp1@ff920000 {
+		compatible = "rockchip,rk3399-cif-isp";
+		reg = <0x0 0xff920000 0x0 0x4000>;
+		interrupts = <GIC_SPI 44 IRQ_TYPE_LEVEL_HIGH 0>;
+		clocks = <&cru SCLK_ISP1>,
+			 <&cru ACLK_ISP1_WRAPPER>,
+			 <&cru HCLK_ISP1_WRAPPER>;
+		clock-names = "isp", "aclk", "hclk";
+		iommus = <&isp1_mmu>;
+		phys = <&mipi_dsi1>;
+		phy-names = "dphy";
+		power-domains = <&power RK3399_PD_ISP1>;
+		status = "disabled";
+
+		ports {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			port@0 {
+				reg = <0>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+			};
+		};
+	};
+
 	isp1_mmu: iommu@ff924000 {
 		compatible = "rockchip,iommu";
 		reg = <0x0 0xff924000 0x0 0x100>, <0x0 0xff925000 0x0 0x100>;
 		interrupts = <GIC_SPI 44 IRQ_TYPE_LEVEL_HIGH 0>;
-		interrupt-names = "isp1_mmu";
 		clocks = <&cru ACLK_ISP1_WRAPPER>, <&cru HCLK_ISP1_WRAPPER>;
 		clock-names = "aclk", "iface";
 		#iommu-cells = <0>;
@@ -1878,6 +1957,7 @@
 		rockchip,grf = <&grf>;
 		#address-cells = <1>;
 		#size-cells = <0>;
+		#phy-cells = <0>;
 		status = "disabled";
 
 		ports {
@@ -1958,7 +2038,7 @@
 		#size-cells = <2>;
 		ranges;
 
-		gpio0: gpio0@ff720000 {
+		gpio0: gpio@ff720000 {
 			compatible = "rockchip,gpio-bank";
 			reg = <0x0 0xff720000 0x0 0x100>;
 			clocks = <&pmucru PCLK_GPIO0_PMU>;
@@ -1971,7 +2051,7 @@
 			#interrupt-cells = <0x2>;
 		};
 
-		gpio1: gpio1@ff730000 {
+		gpio1: gpio@ff730000 {
 			compatible = "rockchip,gpio-bank";
 			reg = <0x0 0xff730000 0x0 0x100>;
 			clocks = <&pmucru PCLK_GPIO1_PMU>;
@@ -1984,7 +2064,7 @@
 			#interrupt-cells = <0x2>;
 		};
 
-		gpio2: gpio2@ff780000 {
+		gpio2: gpio@ff780000 {
 			compatible = "rockchip,gpio-bank";
 			reg = <0x0 0xff780000 0x0 0x100>;
 			clocks = <&cru PCLK_GPIO2>;
@@ -1997,7 +2077,7 @@
 			#interrupt-cells = <0x2>;
 		};
 
-		gpio3: gpio3@ff788000 {
+		gpio3: gpio@ff788000 {
 			compatible = "rockchip,gpio-bank";
 			reg = <0x0 0xff788000 0x0 0x100>;
 			clocks = <&cru PCLK_GPIO3>;
@@ -2010,7 +2090,7 @@
 			#interrupt-cells = <0x2>;
 		};
 
-		gpio4: gpio4@ff790000 {
+		gpio4: gpio@ff790000 {
 			compatible = "rockchip,gpio-bank";
 			reg = <0x0 0xff790000 0x0 0x100>;
 			clocks = <&cru PCLK_GPIO4>;
@@ -2114,6 +2194,18 @@
 			};
 		};
 
+		cif {
+			cif_clkin: cif-clkin {
+				rockchip,pins =
+					<2 RK_PB2 3 &pcfg_pull_none>;
+			};
+
+			cif_clkouta: cif-clkouta {
+				rockchip,pins =
+					<2 RK_PB3 3 &pcfg_pull_none>;
+			};
+		};
+
 		edp {
 			edp_hpd: edp-hpd {
 				rockchip,pins =
diff --git a/arch/arm64/boot/dts/rockchip/rk3566-quartz64-a.dts b/arch/arm64/boot/dts/rockchip/rk3566-quartz64-a.dts
new file mode 100644
index 000000000000..4d4b2a301b1a
--- /dev/null
+++ b/arch/arm64/boot/dts/rockchip/rk3566-quartz64-a.dts
@@ -0,0 +1,548 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+
+/dts-v1/;
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/pinctrl/rockchip.h>
+#include "rk3566.dtsi"
+
+/ {
+	model = "Pine64 RK3566 Quartz64-A Board";
+	compatible = "pine64,quartz64-a", "rockchip,rk3566";
+
+	aliases {
+		ethernet0 = &gmac1;
+		mmc0 = &sdmmc0;
+		mmc1 = &sdhci;
+	};
+
+	chosen: chosen {
+		stdout-path = "serial2:1500000n8";
+	};
+
+	gmac1_clkin: external-gmac1-clock {
+		compatible = "fixed-clock";
+		clock-frequency = <125000000>;
+		clock-output-names = "gmac1_clkin";
+		#clock-cells = <0>;
+	};
+
+	fan: gpio_fan {
+		compatible = "gpio-fan";
+		gpios = <&gpio0 RK_PD5 GPIO_ACTIVE_HIGH>;
+		gpio-fan,speed-map = <0    0
+				      4500 1>;
+		#cooling-cells = <2>;
+	};
+
+	leds {
+		compatible = "gpio-leds";
+
+		led-work {
+			label = "work-led";
+			default-state = "off";
+			gpios = <&gpio0 RK_PD3 GPIO_ACTIVE_HIGH>;
+			pinctrl-names = "default";
+			pinctrl-0 = <&work_led_enable_h>;
+			retain-state-suspended;
+		};
+
+		led-diy {
+			label = "diy-led";
+			default-state = "on";
+			gpios = <&gpio0 RK_PD4 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "heartbeat";
+			pinctrl-names = "default";
+			pinctrl-0 = <&diy_led_enable_h>;
+			retain-state-suspended;
+		};
+	};
+
+	rk817-sound {
+		compatible = "simple-audio-card";
+		simple-audio-card,format = "i2s";
+		simple-audio-card,name = "Analog RK817";
+		simple-audio-card,mclk-fs = <256>;
+
+		simple-audio-card,cpu {
+			sound-dai = <&i2s1_8ch>;
+		};
+
+		simple-audio-card,codec {
+			sound-dai = <&rk817>;
+		};
+	};
+
+	spdif_dit: spdif-dit {
+		compatible = "linux,spdif-dit";
+		#sound-dai-cells = <0>;
+	};
+
+	spdif_sound: spdif-sound {
+		compatible = "simple-audio-card";
+		simple-audio-card,name = "SPDIF";
+
+		simple-audio-card,cpu {
+			sound-dai = <&spdif>;
+		};
+
+		simple-audio-card,codec {
+			sound-dai = <&spdif_dit>;
+		};
+	};
+
+	vcc12v_dcin: vcc12v_dcin {
+		compatible = "regulator-fixed";
+		regulator-name = "vcc12v_dcin";
+		regulator-always-on;
+		regulator-boot-on;
+		regulator-min-microvolt = <12000000>;
+		regulator-max-microvolt = <12000000>;
+	};
+
+	/* vbus feeds the rk817 usb input.
+	 * With no battery attached, also feeds vcc_bat+
+	 * via ON/OFF_BAT jumper
+	 */
+	vbus: vbus {
+		compatible = "regulator-fixed";
+		regulator-name = "vbus";
+		regulator-always-on;
+		regulator-boot-on;
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		vin-supply = <&vcc12v_dcin>;
+	};
+
+	vcc5v0_usb: vcc5v0_usb {
+		compatible = "regulator-fixed";
+		regulator-name = "vcc5v0_usb";
+		regulator-always-on;
+		regulator-boot-on;
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		vin-supply = <&vcc12v_dcin>;
+	};
+
+	vcc3v3_sd: vcc3v3_sd {
+		compatible = "regulator-fixed";
+		enable-active-low;
+		gpio = <&gpio0 RK_PA5 GPIO_ACTIVE_LOW>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&vcc_sd_h>;
+		regulator-boot-on;
+		regulator-name = "vcc3v3_sd";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		vin-supply = <&vcc_3v3>;
+	};
+
+	/* sourced from vbus and vcc_bat+ via rk817 sw5 */
+	vcc_sys: vcc_sys {
+		compatible = "regulator-fixed";
+		regulator-name = "vcc_sys";
+		regulator-always-on;
+		regulator-boot-on;
+		regulator-min-microvolt = <4400000>;
+		regulator-max-microvolt = <4400000>;
+		vin-supply = <&vbus>;
+	};
+};
+
+&cpu0 {
+	cpu-supply = <&vdd_cpu>;
+};
+
+&cpu1 {
+	cpu-supply = <&vdd_cpu>;
+};
+
+&cpu2 {
+	cpu-supply = <&vdd_cpu>;
+};
+
+&cpu3 {
+	cpu-supply = <&vdd_cpu>;
+};
+
+&cpu_thermal {
+	trips {
+		cpu_hot: cpu_hot {
+			temperature = <55000>;
+			hysteresis = <2000>;
+			type = "active";
+		};
+	};
+
+	cooling-maps {
+		map1 {
+			trip = <&cpu_hot>;
+			cooling-device = <&fan THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
+		};
+	};
+};
+
+&gmac1 {
+	assigned-clocks = <&cru SCLK_GMAC1_RX_TX>, <&cru SCLK_GMAC1_RGMII_SPEED>, <&cru SCLK_GMAC1>;
+	assigned-clock-parents = <&cru SCLK_GMAC1_RGMII_SPEED>, <&cru SCLK_GMAC1>, <&gmac1_clkin>;
+	clock_in_out = "input";
+	phy-supply = <&vcc_3v3>;
+	phy-mode = "rgmii";
+	pinctrl-names = "default";
+	pinctrl-0 = <&gmac1m0_miim
+		     &gmac1m0_tx_bus2
+		     &gmac1m0_rx_bus2
+		     &gmac1m0_rgmii_clk
+		     &gmac1m0_clkinout
+		     &gmac1m0_rgmii_bus>;
+	snps,reset-gpio = <&gpio0 RK_PC3 GPIO_ACTIVE_LOW>;
+	snps,reset-active-low;
+	/* Reset time is 20ms, 100ms for rtl8211f */
+	snps,reset-delays-us = <0 20000 100000>;
+	tx_delay = <0x30>;
+	rx_delay = <0x10>;
+	phy-handle = <&rgmii_phy1>;
+	status = "okay";
+};
+
+&i2c0 {
+	status = "okay";
+
+	vdd_cpu: regulator@1c {
+		compatible = "tcs,tcs4525";
+		reg = <0x1c>;
+		fcs,suspend-voltage-selector = <1>;
+		regulator-name = "vdd_cpu";
+		regulator-min-microvolt = <800000>;
+		regulator-max-microvolt = <1150000>;
+		regulator-ramp-delay = <2300>;
+		regulator-always-on;
+		regulator-boot-on;
+		vin-supply = <&vcc_sys>;
+
+		regulator-state-mem {
+			regulator-off-in-suspend;
+		};
+	};
+
+	rk817: pmic@20 {
+		compatible = "rockchip,rk817";
+		reg = <0x20>;
+		interrupt-parent = <&gpio0>;
+		interrupts = <RK_PA3 IRQ_TYPE_LEVEL_LOW>;
+		assigned-clocks = <&cru I2S1_MCLKOUT_TX>;
+		assigned-clock-parents = <&cru CLK_I2S1_8CH_TX>;
+		clock-names = "mclk";
+		clocks = <&cru I2S1_MCLKOUT_TX>;
+		clock-output-names = "rk808-clkout1", "rk808-clkout2";
+		#clock-cells = <1>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pmic_int_l>, <&i2s1m0_mclk>;
+		rockchip,system-power-controller;
+		#sound-dai-cells = <0>;
+		wakeup-source;
+
+		vcc1-supply = <&vcc_sys>;
+		vcc2-supply = <&vcc_sys>;
+		vcc3-supply = <&vcc_sys>;
+		vcc4-supply = <&vcc_sys>;
+		vcc5-supply = <&vcc_sys>;
+		vcc6-supply = <&vcc_sys>;
+		vcc7-supply = <&vcc_sys>;
+		vcc8-supply = <&vcc_sys>;
+		vcc9-supply = <&dcdc_boost>;
+
+		regulators {
+			vdd_logic: DCDC_REG1 {
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <500000>;
+				regulator-max-microvolt = <1350000>;
+				regulator-init-microvolt = <900000>;
+				regulator-ramp-delay = <6001>;
+				regulator-initial-mode = <0x2>;
+				regulator-name = "vdd_logic";
+				regulator-state-mem {
+					regulator-on-in-suspend;
+					regulator-suspend-microvolt = <900000>;
+				};
+			};
+
+			vdd_gpu: DCDC_REG2 {
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <500000>;
+				regulator-max-microvolt = <1350000>;
+				regulator-init-microvolt = <900000>;
+				regulator-ramp-delay = <6001>;
+				regulator-initial-mode = <0x2>;
+				regulator-name = "vdd_gpu";
+					regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			vcc_ddr: DCDC_REG3 {
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <1100000>;
+				regulator-max-microvolt = <1100000>;
+				regulator-initial-mode = <0x2>;
+				regulator-name = "vcc_ddr";
+				regulator-state-mem {
+					regulator-on-in-suspend;
+				};
+			};
+
+			vcc_3v3: DCDC_REG4 {
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-initial-mode = <0x2>;
+				regulator-name = "vcc_3v3";
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			vcca1v8_pmu: LDO_REG1 {
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+				regulator-name = "vcca1v8_pmu";
+				regulator-state-mem {
+					regulator-on-in-suspend;
+					regulator-suspend-microvolt = <1800000>;
+				};
+			};
+
+			vdda_0v9: LDO_REG2 {
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <900000>;
+				regulator-max-microvolt = <900000>;
+				regulator-name = "vdda_0v9";
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			vdda0v9_pmu: LDO_REG3 {
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <900000>;
+				regulator-max-microvolt = <900000>;
+				regulator-name = "vdda0v9_pmu";
+				regulator-state-mem {
+					regulator-on-in-suspend;
+					regulator-suspend-microvolt = <900000>;
+				};
+			};
+
+			vccio_acodec: LDO_REG4 {
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-name = "vccio_acodec";
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			vccio_sd: LDO_REG5 {
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-name = "vccio_sd";
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			vcc3v3_pmu: LDO_REG6 {
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-name = "vcc3v3_pmu";
+				regulator-state-mem {
+					regulator-on-in-suspend;
+					regulator-suspend-microvolt = <3300000>;
+				};
+			};
+
+			vcc_1v8: LDO_REG7 {
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+				regulator-name = "vcc_1v8";
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			vcc1v8_dvp: LDO_REG8 {
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+				regulator-name = "vcc1v8_dvp";
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			vcc2v8_dvp: LDO_REG9 {
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <2800000>;
+				regulator-max-microvolt = <2800000>;
+				regulator-name = "vcc2v8_dvp";
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			dcdc_boost: BOOST {
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <5000000>;
+				regulator-max-microvolt = <5000000>;
+				regulator-name = "boost";
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			otg_switch: OTG_SWITCH {
+				regulator-name = "otg_switch";
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+		};
+	};
+};
+
+&i2s1_8ch {
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2s1m0_sclktx
+		     &i2s1m0_lrcktx
+		     &i2s1m0_sdi0
+		     &i2s1m0_sdo0>;
+	rockchip,trcm-sync-tx-only;
+	status = "okay";
+};
+
+&mdio1 {
+	rgmii_phy1: ethernet-phy@0 {
+		compatible = "ethernet-phy-ieee802.3-c22";
+		reg = <0>;
+	};
+};
+
+&pinctrl {
+	bt {
+		bt_enable_h: bt-enable-h {
+			rockchip,pins = <2 RK_PB7 RK_FUNC_GPIO &pcfg_pull_none>;
+		};
+
+		bt_host_wake_l: bt-host-wake-l {
+			rockchip,pins = <2 RK_PC0 RK_FUNC_GPIO &pcfg_pull_down>;
+		};
+
+		bt_wake_l: bt-wake-l {
+			rockchip,pins = <2 RK_PC1 RK_FUNC_GPIO &pcfg_pull_none>;
+		};
+	};
+
+	leds {
+		work_led_enable_h: work-led-enable-h {
+			rockchip,pins = <0 RK_PD3 RK_FUNC_GPIO &pcfg_pull_none>;
+		};
+
+		diy_led_enable_h: diy-led-enable-h {
+			rockchip,pins = <0 RK_PD4 RK_FUNC_GPIO &pcfg_pull_none>;
+		};
+	};
+
+	pmic {
+		pmic_int_l: pmic-int-l {
+			rockchip,pins = <0 RK_PA3 RK_FUNC_GPIO &pcfg_pull_up>;
+		};
+	};
+
+	vcc_sd {
+		vcc_sd_h: vcc-sd-h {
+			rockchip,pins = <0 RK_PA5 RK_FUNC_GPIO &pcfg_pull_none>;
+		};
+	};
+};
+
+&sdhci {
+	bus-width = <8>;
+	mmc-hs200-1_8v;
+	non-removable;
+	vmmc-supply = <&vcc_3v3>;
+	vqmmc-supply = <&vcc_1v8>;
+	status = "okay";
+};
+
+&sdmmc0 {
+	bus-width = <4>;
+	cap-sd-highspeed;
+	cd-gpios = <&gpio0 RK_PA4 GPIO_ACTIVE_LOW>;
+	disable-wp;
+	pinctrl-names = "default";
+	pinctrl-0 = <&sdmmc0_bus4 &sdmmc0_clk &sdmmc0_cmd &sdmmc0_det>;
+	vmmc-supply = <&vcc3v3_sd>;
+	vqmmc-supply = <&vccio_sd>;
+	status = "okay";
+};
+
+&spdif {
+	status = "okay";
+};
+
+&tsadc {
+	/* tshut mode 0:CRU 1:GPIO */
+	rockchip,hw-tshut-mode = <1>;
+	/* tshut polarity 0:LOW 1:HIGH */
+	rockchip,hw-tshut-polarity = <0>;
+	status = "okay";
+};
+
+&uart0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart0_xfer>;
+	status = "okay";
+};
+
+&uart1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart1m0_xfer &uart1m0_ctsn>;
+	status = "okay";
+	uart-has-rtscts;
+
+	bluetooth {
+		compatible = "brcm,bcm43438-bt";
+		clocks = <&rk817 1>;
+		clock-names = "lpo";
+		device-wake-gpios = <&gpio2 RK_PC1 GPIO_ACTIVE_HIGH>;
+		host-wake-gpios = <&gpio2 RK_PC0 GPIO_ACTIVE_HIGH>;
+		shutdown-gpios = <&gpio2 RK_PB7 GPIO_ACTIVE_HIGH>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&bt_host_wake_l &bt_wake_l &bt_enable_h>;
+		vbat-supply = <&vcc_sys>;
+		vddio-supply = <&vcca1v8_pmu>;
+	};
+};
+
+&uart2 {
+	status = "okay";
+};
diff --git a/arch/arm64/boot/dts/rockchip/rk3566.dtsi b/arch/arm64/boot/dts/rockchip/rk3566.dtsi
new file mode 100644
index 000000000000..3839eef5e4f7
--- /dev/null
+++ b/arch/arm64/boot/dts/rockchip/rk3566.dtsi
@@ -0,0 +1,20 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+
+#include "rk356x.dtsi"
+
+/ {
+	compatible = "rockchip,rk3566";
+};
+
+&power {
+	power-domain@RK3568_PD_PIPE {
+		reg = <RK3568_PD_PIPE>;
+		clocks = <&cru PCLK_PIPE>;
+		pm_qos = <&qos_pcie2x1>,
+			 <&qos_sata1>,
+			 <&qos_sata2>,
+			 <&qos_usb3_0>,
+			 <&qos_usb3_1>;
+		#power-domain-cells = <0>;
+	};
+};
diff --git a/arch/arm64/boot/dts/rockchip/rk3568-evb1-v10.dts b/arch/arm64/boot/dts/rockchip/rk3568-evb1-v10.dts
index 69786557093d..184e2aa2416a 100644
--- a/arch/arm64/boot/dts/rockchip/rk3568-evb1-v10.dts
+++ b/arch/arm64/boot/dts/rockchip/rk3568-evb1-v10.dts
@@ -13,6 +13,13 @@
 	model = "Rockchip RK3568 EVB1 DDR4 V10 Board";
 	compatible = "rockchip,rk3568-evb1-v10", "rockchip,rk3568";
 
+	aliases {
+		ethernet0 = &gmac0;
+		ethernet1 = &gmac1;
+		mmc0 = &sdmmc0;
+		mmc1 = &sdhci;
+	};
+
 	chosen: chosen {
 		stdout-path = "serial2:1500000n8";
 	};
@@ -67,10 +74,316 @@
 	};
 };
 
+&gmac0 {
+	assigned-clocks = <&cru SCLK_GMAC0_RX_TX>, <&cru SCLK_GMAC0>;
+	assigned-clock-parents = <&cru SCLK_GMAC0_RGMII_SPEED>;
+	assigned-clock-rates = <0>, <125000000>;
+	clock_in_out = "output";
+	phy-handle = <&rgmii_phy0>;
+	phy-mode = "rgmii-id";
+	pinctrl-names = "default";
+	pinctrl-0 = <&gmac0_miim
+		     &gmac0_tx_bus2
+		     &gmac0_rx_bus2
+		     &gmac0_rgmii_clk
+		     &gmac0_rgmii_bus>;
+	status = "okay";
+};
+
+&gmac1 {
+	assigned-clocks = <&cru SCLK_GMAC1_RX_TX>, <&cru SCLK_GMAC1>;
+	assigned-clock-parents = <&cru SCLK_GMAC1_RGMII_SPEED>;
+	assigned-clock-rates = <0>, <125000000>;
+	clock_in_out = "output";
+	phy-handle = <&rgmii_phy1>;
+	phy-mode = "rgmii-id";
+	pinctrl-names = "default";
+	pinctrl-0 = <&gmac1m1_miim
+		     &gmac1m1_tx_bus2
+		     &gmac1m1_rx_bus2
+		     &gmac1m1_rgmii_clk
+		     &gmac1m1_rgmii_bus>;
+	status = "okay";
+};
+
+&i2c0 {
+	status = "okay";
+
+	rk809: pmic@20 {
+		compatible = "rockchip,rk809";
+		reg = <0x20>;
+		interrupt-parent = <&gpio0>;
+		interrupts = <RK_PA3 IRQ_TYPE_LEVEL_LOW>;
+		#clock-cells = <1>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pmic_int>;
+		rockchip,system-power-controller;
+		vcc1-supply = <&vcc3v3_sys>;
+		vcc2-supply = <&vcc3v3_sys>;
+		vcc3-supply = <&vcc3v3_sys>;
+		vcc4-supply = <&vcc3v3_sys>;
+		vcc5-supply = <&vcc3v3_sys>;
+		vcc6-supply = <&vcc3v3_sys>;
+		vcc7-supply = <&vcc3v3_sys>;
+		vcc8-supply = <&vcc3v3_sys>;
+		vcc9-supply = <&vcc3v3_sys>;
+		wakeup-source;
+
+		regulators {
+			vdd_logic: DCDC_REG1 {
+				regulator-name = "vdd_logic";
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-init-microvolt = <900000>;
+				regulator-initial-mode = <0x2>;
+				regulator-min-microvolt = <500000>;
+				regulator-max-microvolt = <1350000>;
+				regulator-ramp-delay = <6001>;
+
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			vdd_gpu: DCDC_REG2 {
+				regulator-name = "vdd_gpu";
+				regulator-init-microvolt = <900000>;
+				regulator-initial-mode = <0x2>;
+				regulator-min-microvolt = <500000>;
+				regulator-max-microvolt = <1350000>;
+				regulator-ramp-delay = <6001>;
+
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			vcc_ddr: DCDC_REG3 {
+				regulator-name = "vcc_ddr";
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-initial-mode = <0x2>;
+
+				regulator-state-mem {
+					regulator-on-in-suspend;
+				};
+			};
+
+			vdd_npu: DCDC_REG4 {
+				regulator-name = "vdd_npu";
+				regulator-init-microvolt = <900000>;
+				regulator-initial-mode = <0x2>;
+				regulator-min-microvolt = <500000>;
+				regulator-max-microvolt = <1350000>;
+				regulator-ramp-delay = <6001>;
+
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			vcc_1v8: DCDC_REG5 {
+				regulator-name = "vcc_1v8";
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			vdda0v9_image: LDO_REG1 {
+				regulator-name = "vdda0v9_image";
+				regulator-min-microvolt = <900000>;
+				regulator-max-microvolt = <900000>;
+
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			vdda_0v9: LDO_REG2 {
+				regulator-name = "vdda_0v9";
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <900000>;
+				regulator-max-microvolt = <900000>;
+
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			vdda0v9_pmu: LDO_REG3 {
+				regulator-name = "vdda0v9_pmu";
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <900000>;
+				regulator-max-microvolt = <900000>;
+
+				regulator-state-mem {
+					regulator-on-in-suspend;
+					regulator-suspend-microvolt = <900000>;
+				};
+			};
+
+			vccio_acodec: LDO_REG4 {
+				regulator-name = "vccio_acodec";
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
+
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			vccio_sd: LDO_REG5 {
+				regulator-name = "vccio_sd";
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <3300000>;
+
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			vcc3v3_pmu: LDO_REG6 {
+				regulator-name = "vcc3v3_pmu";
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
+
+				regulator-state-mem {
+					regulator-on-in-suspend;
+					regulator-suspend-microvolt = <3300000>;
+				};
+			};
+
+			vcca_1v8: LDO_REG7 {
+				regulator-name = "vcca_1v8";
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			vcca1v8_pmu: LDO_REG8 {
+				regulator-name = "vcca1v8_pmu";
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+
+				regulator-state-mem {
+					regulator-on-in-suspend;
+					regulator-suspend-microvolt = <1800000>;
+				};
+			};
+
+			vcca1v8_image: LDO_REG9 {
+				regulator-name = "vcca1v8_image";
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			vcc_3v3: SWITCH_REG1 {
+				regulator-name = "vcc_3v3";
+				regulator-always-on;
+				regulator-boot-on;
+
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			vcc3v3_sd: SWITCH_REG2 {
+				regulator-name = "vcc3v3_sd";
+
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+		};
+	};
+};
+
+&mdio0 {
+	rgmii_phy0: ethernet-phy@0 {
+		compatible = "ethernet-phy-ieee802.3-c22";
+		reg = <0x0>;
+		reset-assert-us = <20000>;
+		reset-deassert-us = <100000>;
+		reset-gpios = <&gpio2 RK_PD3 GPIO_ACTIVE_LOW>;
+	};
+};
+
+&mdio1 {
+	rgmii_phy1: ethernet-phy@0 {
+		compatible = "ethernet-phy-ieee802.3-c22";
+		reg = <0x0>;
+		reset-assert-us = <20000>;
+		reset-deassert-us = <100000>;
+		reset-gpios = <&gpio2 RK_PD1 GPIO_ACTIVE_LOW>;
+	};
+};
+
+&pinctrl {
+	pmic {
+		pmic_int: pmic_int {
+			rockchip,pins =
+				<0 RK_PA3 RK_FUNC_GPIO &pcfg_pull_up>;
+		};
+	};
+};
+
+&pmu_io_domains {
+	pmuio1-supply = <&vcc3v3_pmu>;
+	pmuio2-supply = <&vcc3v3_pmu>;
+	vccio1-supply = <&vccio_acodec>;
+	vccio2-supply = <&vcc_1v8>;
+	vccio3-supply = <&vccio_sd>;
+	vccio4-supply = <&vcc_1v8>;
+	vccio5-supply = <&vcc_3v3>;
+	vccio6-supply = <&vcc_1v8>;
+	vccio7-supply = <&vcc_3v3>;
+	status = "okay";
+};
+
+&saradc {
+	vref-supply = <&vcca_1v8>;
+	status = "okay";
+};
+
 &sdhci {
 	bus-width = <8>;
 	max-frequency = <200000000>;
 	non-removable;
+	pinctrl-names = "default";
+	pinctrl-0 = <&emmc_bus8 &emmc_clk &emmc_cmd &emmc_datastrobe>;
+	status = "okay";
+};
+
+&sdmmc0 {
+	bus-width = <4>;
+	cap-sd-highspeed;
+	cd-gpios = <&gpio0 RK_PA4 GPIO_ACTIVE_LOW>;
+	disable-wp;
+	pinctrl-names = "default";
+	pinctrl-0 = <&sdmmc0_bus4 &sdmmc0_clk &sdmmc0_cmd &sdmmc0_det>;
+	sd-uhs-sdr104;
+	vmmc-supply = <&vcc3v3_sd>;
+	vqmmc-supply = <&vccio_sd>;
 	status = "okay";
 };
 
diff --git a/arch/arm64/boot/dts/rockchip/rk3568-pinctrl.dtsi b/arch/arm64/boot/dts/rockchip/rk3568-pinctrl.dtsi
index a588ca95ace2..8f90c66dd9e9 100644
--- a/arch/arm64/boot/dts/rockchip/rk3568-pinctrl.dtsi
+++ b/arch/arm64/boot/dts/rockchip/rk3568-pinctrl.dtsi
@@ -3108,4 +3108,13 @@
 				<4 RK_PA0 3 &pcfg_pull_none_drv_level_2>;
 		};
 	};
+
+	tsadc {
+		/omit-if-no-ref/
+		tsadc_pin: tsadc-pin {
+			rockchip,pins =
+				/* tsadc_pin */
+				<0 RK_PA1 0 &pcfg_pull_none>;
+		};
+	};
 };
diff --git a/arch/arm64/boot/dts/rockchip/rk3568.dtsi b/arch/arm64/boot/dts/rockchip/rk3568.dtsi
index d225e6a45d5c..2fd313a295f8 100644
--- a/arch/arm64/boot/dts/rockchip/rk3568.dtsi
+++ b/arch/arm64/boot/dts/rockchip/rk3568.dtsi
@@ -3,591 +3,95 @@
  * Copyright (c) 2021 Rockchip Electronics Co., Ltd.
  */
 
-#include <dt-bindings/clock/rk3568-cru.h>
-#include <dt-bindings/interrupt-controller/arm-gic.h>
-#include <dt-bindings/interrupt-controller/irq.h>
-#include <dt-bindings/phy/phy.h>
-#include <dt-bindings/pinctrl/rockchip.h>
-#include <dt-bindings/soc/rockchip,boot-mode.h>
-#include <dt-bindings/thermal/thermal.h>
+#include "rk356x.dtsi"
 
 / {
 	compatible = "rockchip,rk3568";
 
-	interrupt-parent = <&gic>;
-	#address-cells = <2>;
-	#size-cells = <2>;
-
-	aliases {
-		gpio0 = &gpio0;
-		gpio1 = &gpio1;
-		gpio2 = &gpio2;
-		gpio3 = &gpio3;
-		gpio4 = &gpio4;
-		i2c0 = &i2c0;
-		i2c1 = &i2c1;
-		i2c2 = &i2c2;
-		i2c3 = &i2c3;
-		i2c4 = &i2c4;
-		i2c5 = &i2c5;
-		serial0 = &uart0;
-		serial1 = &uart1;
-		serial2 = &uart2;
-		serial3 = &uart3;
-		serial4 = &uart4;
-		serial5 = &uart5;
-		serial6 = &uart6;
-		serial7 = &uart7;
-		serial8 = &uart8;
-		serial9 = &uart9;
-	};
-
-	cpus {
-		#address-cells = <2>;
-		#size-cells = <0>;
-
-		cpu0: cpu@0 {
-			device_type = "cpu";
-			compatible = "arm,cortex-a55";
-			reg = <0x0 0x0>;
-			clocks = <&scmi_clk 0>;
-			enable-method = "psci";
-			operating-points-v2 = <&cpu0_opp_table>;
-		};
-
-		cpu1: cpu@100 {
-			device_type = "cpu";
-			compatible = "arm,cortex-a55";
-			reg = <0x0 0x100>;
-			enable-method = "psci";
-			operating-points-v2 = <&cpu0_opp_table>;
-		};
-
-		cpu2: cpu@200 {
-			device_type = "cpu";
-			compatible = "arm,cortex-a55";
-			reg = <0x0 0x200>;
-			enable-method = "psci";
-			operating-points-v2 = <&cpu0_opp_table>;
-		};
-
-		cpu3: cpu@300 {
-			device_type = "cpu";
-			compatible = "arm,cortex-a55";
-			reg = <0x0 0x300>;
-			enable-method = "psci";
-			operating-points-v2 = <&cpu0_opp_table>;
-		};
-	};
-
-	cpu0_opp_table: cpu0-opp-table {
-		compatible = "operating-points-v2";
-		opp-shared;
-
-		opp-408000000 {
-			opp-hz = /bits/ 64 <408000000>;
-			opp-microvolt = <900000 900000 1150000>;
-			clock-latency-ns = <40000>;
-		};
-
-		opp-600000000 {
-			opp-hz = /bits/ 64 <600000000>;
-			opp-microvolt = <900000 900000 1150000>;
-		};
-
-		opp-816000000 {
-			opp-hz = /bits/ 64 <816000000>;
-			opp-microvolt = <900000 900000 1150000>;
-			opp-suspend;
-		};
-
-		opp-1104000000 {
-			opp-hz = /bits/ 64 <1104000000>;
-			opp-microvolt = <900000 900000 1150000>;
-		};
-
-		opp-1416000000 {
-			opp-hz = /bits/ 64 <1416000000>;
-			opp-microvolt = <900000 900000 1150000>;
-		};
-
-		opp-1608000000 {
-			opp-hz = /bits/ 64 <1608000000>;
-			opp-microvolt = <975000 975000 1150000>;
-		};
+	qos_pcie3x1: qos@fe190080 {
+		compatible = "rockchip,rk3568-qos", "syscon";
+		reg = <0x0 0xfe190080 0x0 0x20>;
+	};
+
+	qos_pcie3x2: qos@fe190100 {
+		compatible = "rockchip,rk3568-qos", "syscon";
+		reg = <0x0 0xfe190100 0x0 0x20>;
+	};
+
+	qos_sata0: qos@fe190200 {
+		compatible = "rockchip,rk3568-qos", "syscon";
+		reg = <0x0 0xfe190200 0x0 0x20>;
+	};
+
+	gmac0: ethernet@fe2a0000 {
+		compatible = "rockchip,rk3568-gmac", "snps,dwmac-4.20a";
+		reg = <0x0 0xfe2a0000 0x0 0x10000>;
+		interrupts = <GIC_SPI 27 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 24 IRQ_TYPE_LEVEL_HIGH>;
+		interrupt-names = "macirq", "eth_wake_irq";
+		clocks = <&cru SCLK_GMAC0>, <&cru SCLK_GMAC0_RX_TX>,
+			 <&cru SCLK_GMAC0_RX_TX>, <&cru CLK_MAC0_REFOUT>,
+			 <&cru ACLK_GMAC0>, <&cru PCLK_GMAC0>,
+			 <&cru SCLK_GMAC0_RX_TX>, <&cru CLK_GMAC0_PTP_REF>,
+			 <&cru PCLK_XPCS>;
+		clock-names = "stmmaceth", "mac_clk_rx",
+			      "mac_clk_tx", "clk_mac_refout",
+			      "aclk_mac", "pclk_mac",
+			      "clk_mac_speed", "ptp_ref",
+			      "pclk_xpcs";
+		resets = <&cru SRST_A_GMAC0>;
+		reset-names = "stmmaceth";
+		rockchip,grf = <&grf>;
+		snps,axi-config = <&gmac0_stmmac_axi_setup>;
+		snps,mixed-burst;
+		snps,mtl-rx-config = <&gmac0_mtl_rx_setup>;
+		snps,mtl-tx-config = <&gmac0_mtl_tx_setup>;
+		snps,tso;
+		status = "disabled";
 
-		opp-1800000000 {
-			opp-hz = /bits/ 64 <1800000000>;
-			opp-microvolt = <1050000 1050000 1150000>;
+		mdio0: mdio {
+			compatible = "snps,dwmac-mdio";
+			#address-cells = <0x1>;
+			#size-cells = <0x0>;
 		};
 
-		opp-1992000000 {
-			opp-hz = /bits/ 64 <1992000000>;
-			opp-microvolt = <1150000 1150000 1150000>;
+		gmac0_stmmac_axi_setup: stmmac-axi-config {
+			snps,blen = <0 0 0 0 16 8 4>;
+			snps,rd_osr_lmt = <8>;
+			snps,wr_osr_lmt = <4>;
 		};
-	};
 
-	firmware {
-		scmi: scmi {
-			compatible = "arm,scmi-smc";
-			arm,smc-id = <0x82000010>;
-			shmem = <&scmi_shmem>;
-			#address-cells = <1>;
-			#size-cells = <0>;
-
-			scmi_clk: protocol@14 {
-				reg = <0x14>;
-				#clock-cells = <1>;
-			};
+		gmac0_mtl_rx_setup: rx-queues-config {
+			snps,rx-queues-to-use = <1>;
+			queue0 {};
 		};
-	};
-
-	pmu {
-		compatible = "arm,cortex-a55-pmu";
-		interrupts = <GIC_SPI 228 IRQ_TYPE_LEVEL_HIGH>,
-			     <GIC_SPI 229 IRQ_TYPE_LEVEL_HIGH>,
-			     <GIC_SPI 230 IRQ_TYPE_LEVEL_HIGH>,
-			     <GIC_SPI 231 IRQ_TYPE_LEVEL_HIGH>;
-		interrupt-affinity = <&cpu0>, <&cpu1>, <&cpu2>, <&cpu3>;
-	};
 
-	psci {
-		compatible = "arm,psci-1.0";
-		method = "smc";
-	};
-
-	timer {
-		compatible = "arm,armv8-timer";
-		interrupts = <GIC_PPI 13 IRQ_TYPE_LEVEL_HIGH>,
-			     <GIC_PPI 14 IRQ_TYPE_LEVEL_HIGH>,
-			     <GIC_PPI 11 IRQ_TYPE_LEVEL_HIGH>,
-			     <GIC_PPI 10 IRQ_TYPE_LEVEL_HIGH>;
-		arm,no-tick-in-suspend;
-	};
-
-	xin24m: xin24m {
-		compatible = "fixed-clock";
-		clock-frequency = <24000000>;
-		clock-output-names = "xin24m";
-		#clock-cells = <0>;
-	};
-
-	xin32k: xin32k {
-		compatible = "fixed-clock";
-		clock-frequency = <32768>;
-		clock-output-names = "xin32k";
-		pinctrl-0 = <&clk32k_out0>;
-		pinctrl-names = "default";
-		#clock-cells = <0>;
-	};
-
-	sram@10f000 {
-		compatible = "mmio-sram";
-		reg = <0x0 0x0010f000 0x0 0x100>;
-		#address-cells = <1>;
-		#size-cells = <1>;
-		ranges = <0 0x0 0x0010f000 0x100>;
-
-		scmi_shmem: sram@0 {
-			compatible = "arm,scmi-shmem";
-			reg = <0x0 0x100>;
+		gmac0_mtl_tx_setup: tx-queues-config {
+			snps,tx-queues-to-use = <1>;
+			queue0 {};
 		};
 	};
+};
 
-	gic: interrupt-controller@fd400000 {
-		compatible = "arm,gic-v3";
-		reg = <0x0 0xfd400000 0 0x10000>, /* GICD */
-		      <0x0 0xfd460000 0 0x80000>; /* GICR */
-		interrupts = <GIC_PPI 9 IRQ_TYPE_LEVEL_HIGH>;
-		interrupt-controller;
-		#interrupt-cells = <3>;
-		mbi-alias = <0x0 0xfd100000>;
-		mbi-ranges = <296 24>;
-		msi-controller;
-	};
-
-	pmugrf: syscon@fdc20000 {
-		compatible = "rockchip,rk3568-pmugrf", "syscon", "simple-mfd";
-		reg = <0x0 0xfdc20000 0x0 0x10000>;
-	};
-
-	grf: syscon@fdc60000 {
-		compatible = "rockchip,rk3568-grf", "syscon", "simple-mfd";
-		reg = <0x0 0xfdc60000 0x0 0x10000>;
-	};
-
-	pmucru: clock-controller@fdd00000 {
-		compatible = "rockchip,rk3568-pmucru";
-		reg = <0x0 0xfdd00000 0x0 0x1000>;
-		#clock-cells = <1>;
-		#reset-cells = <1>;
-	};
-
-	cru: clock-controller@fdd20000 {
-		compatible = "rockchip,rk3568-cru";
-		reg = <0x0 0xfdd20000 0x0 0x1000>;
-		#clock-cells = <1>;
-		#reset-cells = <1>;
-	};
-
-	i2c0: i2c@fdd40000 {
-		compatible = "rockchip,rk3568-i2c", "rockchip,rk3399-i2c";
-		reg = <0x0 0xfdd40000 0x0 0x1000>;
-		interrupts = <GIC_SPI 46 IRQ_TYPE_LEVEL_HIGH>;
-		clocks = <&pmucru CLK_I2C0>, <&pmucru PCLK_I2C0>;
-		clock-names = "i2c", "pclk";
-		pinctrl-0 = <&i2c0_xfer>;
-		pinctrl-names = "default";
-		#address-cells = <1>;
-		#size-cells = <0>;
-		status = "disabled";
-	};
-
-	uart0: serial@fdd50000 {
-		compatible = "rockchip,rk3568-uart", "snps,dw-apb-uart";
-		reg = <0x0 0xfdd50000 0x0 0x100>;
-		interrupts = <GIC_SPI 116 IRQ_TYPE_LEVEL_HIGH>;
-		clocks = <&pmucru SCLK_UART0>, <&pmucru PCLK_UART0>;
-		clock-names = "baudclk", "apb_pclk";
-		dmas = <&dmac0 0>, <&dmac0 1>;
-		pinctrl-0 = <&uart0_xfer>;
-		pinctrl-names = "default";
-		reg-io-width = <4>;
-		reg-shift = <2>;
-		status = "disabled";
-	};
-
-	sdmmc2: mmc@fe000000 {
-		compatible = "rockchip,rk3568-dw-mshc", "rockchip,rk3288-dw-mshc";
-		reg = <0x0 0xfe000000 0x0 0x4000>;
-		interrupts = <GIC_SPI 100 IRQ_TYPE_LEVEL_HIGH>;
-		clocks = <&cru HCLK_SDMMC2>, <&cru CLK_SDMMC2>,
-			 <&cru SCLK_SDMMC2_DRV>, <&cru SCLK_SDMMC2_SAMPLE>;
-		clock-names = "biu", "ciu", "ciu-drive", "ciu-sample";
-		fifo-depth = <0x100>;
-		max-frequency = <150000000>;
-		resets = <&cru SRST_SDMMC2>;
-		reset-names = "reset";
-		status = "disabled";
-	};
-
-	sdmmc0: mmc@fe2b0000 {
-		compatible = "rockchip,rk3568-dw-mshc", "rockchip,rk3288-dw-mshc";
-		reg = <0x0 0xfe2b0000 0x0 0x4000>;
-		interrupts = <GIC_SPI 98 IRQ_TYPE_LEVEL_HIGH>;
-		clocks = <&cru HCLK_SDMMC0>, <&cru CLK_SDMMC0>,
-			 <&cru SCLK_SDMMC0_DRV>, <&cru SCLK_SDMMC0_SAMPLE>;
-		clock-names = "biu", "ciu", "ciu-drive", "ciu-sample";
-		fifo-depth = <0x100>;
-		max-frequency = <150000000>;
-		resets = <&cru SRST_SDMMC0>;
-		reset-names = "reset";
-		status = "disabled";
-	};
-
-	sdmmc1: mmc@fe2c0000 {
-		compatible = "rockchip,rk3568-dw-mshc", "rockchip,rk3288-dw-mshc";
-		reg = <0x0 0xfe2c0000 0x0 0x4000>;
-		interrupts = <GIC_SPI 99 IRQ_TYPE_LEVEL_HIGH>;
-		clocks = <&cru HCLK_SDMMC1>, <&cru CLK_SDMMC1>,
-			 <&cru SCLK_SDMMC1_DRV>, <&cru SCLK_SDMMC1_SAMPLE>;
-		clock-names = "biu", "ciu", "ciu-drive", "ciu-sample";
-		fifo-depth = <0x100>;
-		max-frequency = <150000000>;
-		resets = <&cru SRST_SDMMC1>;
-		reset-names = "reset";
-		status = "disabled";
-	};
-
-	sdhci: mmc@fe310000 {
-		compatible = "rockchip,rk3568-dwcmshc";
-		reg = <0x0 0xfe310000 0x0 0x10000>;
-		interrupts = <GIC_SPI 19 IRQ_TYPE_LEVEL_HIGH>;
-		assigned-clocks = <&cru BCLK_EMMC>, <&cru TCLK_EMMC>;
-		assigned-clock-rates = <200000000>, <24000000>;
-		clocks = <&cru CCLK_EMMC>, <&cru HCLK_EMMC>,
-			 <&cru ACLK_EMMC>, <&cru BCLK_EMMC>,
-			 <&cru TCLK_EMMC>;
-		clock-names = "core", "bus", "axi", "block", "timer";
-		status = "disabled";
-	};
-
-	dmac0: dmac@fe530000 {
-		compatible = "arm,pl330", "arm,primecell";
-		reg = <0x0 0xfe530000 0x0 0x4000>;
-		interrupts = <GIC_SPI 14 IRQ_TYPE_LEVEL_HIGH>,
-			     <GIC_SPI 13 IRQ_TYPE_LEVEL_HIGH>;
-		arm,pl330-periph-burst;
-		clocks = <&cru ACLK_BUS>;
-		clock-names = "apb_pclk";
-		#dma-cells = <1>;
-	};
-
-	dmac1: dmac@fe550000 {
-		compatible = "arm,pl330", "arm,primecell";
-		reg = <0x0 0xfe550000 0x0 0x4000>;
-		interrupts = <GIC_SPI 16 IRQ_TYPE_LEVEL_HIGH>,
-			     <GIC_SPI 15 IRQ_TYPE_LEVEL_HIGH>;
-		arm,pl330-periph-burst;
-		clocks = <&cru ACLK_BUS>;
-		clock-names = "apb_pclk";
-		#dma-cells = <1>;
-	};
-
-	i2c1: i2c@fe5a0000 {
-		compatible = "rockchip,rk3568-i2c", "rockchip,rk3399-i2c";
-		reg = <0x0 0xfe5a0000 0x0 0x1000>;
-		interrupts = <GIC_SPI 47 IRQ_TYPE_LEVEL_HIGH>;
-		clocks = <&cru CLK_I2C1>, <&cru PCLK_I2C1>;
-		clock-names = "i2c", "pclk";
-		pinctrl-0 = <&i2c1_xfer>;
-		pinctrl-names = "default";
-		#address-cells = <1>;
-		#size-cells = <0>;
-		status = "disabled";
-	};
-
-	i2c2: i2c@fe5b0000 {
-		compatible = "rockchip,rk3568-i2c", "rockchip,rk3399-i2c";
-		reg = <0x0 0xfe5b0000 0x0 0x1000>;
-		interrupts = <GIC_SPI 48 IRQ_TYPE_LEVEL_HIGH>;
-		clocks = <&cru CLK_I2C2>, <&cru PCLK_I2C2>;
-		clock-names = "i2c", "pclk";
-		pinctrl-0 = <&i2c2m0_xfer>;
-		pinctrl-names = "default";
-		#address-cells = <1>;
-		#size-cells = <0>;
-		status = "disabled";
-	};
-
-	i2c3: i2c@fe5c0000 {
-		compatible = "rockchip,rk3568-i2c", "rockchip,rk3399-i2c";
-		reg = <0x0 0xfe5c0000 0x0 0x1000>;
-		interrupts = <GIC_SPI 49 IRQ_TYPE_LEVEL_HIGH>;
-		clocks = <&cru CLK_I2C3>, <&cru PCLK_I2C3>;
-		clock-names = "i2c", "pclk";
-		pinctrl-0 = <&i2c3m0_xfer>;
-		pinctrl-names = "default";
-		#address-cells = <1>;
-		#size-cells = <0>;
-		status = "disabled";
-	};
-
-	i2c4: i2c@fe5d0000 {
-		compatible = "rockchip,rk3568-i2c", "rockchip,rk3399-i2c";
-		reg = <0x0 0xfe5d0000 0x0 0x1000>;
-		interrupts = <GIC_SPI 50 IRQ_TYPE_LEVEL_HIGH>;
-		clocks = <&cru CLK_I2C4>, <&cru PCLK_I2C4>;
-		clock-names = "i2c", "pclk";
-		pinctrl-0 = <&i2c4m0_xfer>;
-		pinctrl-names = "default";
-		#address-cells = <1>;
-		#size-cells = <0>;
-		status = "disabled";
-	};
-
-	i2c5: i2c@fe5e0000 {
-		compatible = "rockchip,rk3568-i2c", "rockchip,rk3399-i2c";
-		reg = <0x0 0xfe5e0000 0x0 0x1000>;
-		interrupts = <GIC_SPI 51 IRQ_TYPE_LEVEL_HIGH>;
-		clocks = <&cru CLK_I2C5>, <&cru PCLK_I2C5>;
-		clock-names = "i2c", "pclk";
-		pinctrl-0 = <&i2c5m0_xfer>;
-		pinctrl-names = "default";
-		#address-cells = <1>;
-		#size-cells = <0>;
-		status = "disabled";
-	};
-
-	uart1: serial@fe650000 {
-		compatible = "rockchip,rk3568-uart", "snps,dw-apb-uart";
-		reg = <0x0 0xfe650000 0x0 0x100>;
-		interrupts = <GIC_SPI 117 IRQ_TYPE_LEVEL_HIGH>;
-		clocks = <&cru SCLK_UART1>, <&cru PCLK_UART1>;
-		clock-names = "baudclk", "apb_pclk";
-		dmas = <&dmac0 2>, <&dmac0 3>;
-		pinctrl-0 = <&uart1m0_xfer>;
-		pinctrl-names = "default";
-		reg-io-width = <4>;
-		reg-shift = <2>;
-		status = "disabled";
-	};
-
-	uart2: serial@fe660000 {
-		compatible = "rockchip,rk3568-uart", "snps,dw-apb-uart";
-		reg = <0x0 0xfe660000 0x0 0x100>;
-		interrupts = <GIC_SPI 118 IRQ_TYPE_LEVEL_HIGH>;
-		clocks = <&cru SCLK_UART2>, <&cru PCLK_UART2>;
-		clock-names = "baudclk", "apb_pclk";
-		dmas = <&dmac0 4>, <&dmac0 5>;
-		pinctrl-0 = <&uart2m0_xfer>;
-		pinctrl-names = "default";
-		reg-io-width = <4>;
-		reg-shift = <2>;
-		status = "disabled";
-	};
-
-	uart3: serial@fe670000 {
-		compatible = "rockchip,rk3568-uart", "snps,dw-apb-uart";
-		reg = <0x0 0xfe670000 0x0 0x100>;
-		interrupts = <GIC_SPI 119 IRQ_TYPE_LEVEL_HIGH>;
-		clocks = <&cru SCLK_UART3>, <&cru PCLK_UART3>;
-		clock-names = "baudclk", "apb_pclk";
-		dmas = <&dmac0 6>, <&dmac0 7>;
-		pinctrl-0 = <&uart3m0_xfer>;
-		pinctrl-names = "default";
-		reg-io-width = <4>;
-		reg-shift = <2>;
-		status = "disabled";
-	};
-
-	uart4: serial@fe680000 {
-		compatible = "rockchip,rk3568-uart", "snps,dw-apb-uart";
-		reg = <0x0 0xfe680000 0x0 0x100>;
-		interrupts = <GIC_SPI 120 IRQ_TYPE_LEVEL_HIGH>;
-		clocks = <&cru SCLK_UART4>, <&cru PCLK_UART4>;
-		clock-names = "baudclk", "apb_pclk";
-		dmas = <&dmac0 8>, <&dmac0 9>;
-		pinctrl-0 = <&uart4m0_xfer>;
-		pinctrl-names = "default";
-		reg-io-width = <4>;
-		reg-shift = <2>;
-		status = "disabled";
-	};
-
-	uart5: serial@fe690000 {
-		compatible = "rockchip,rk3568-uart", "snps,dw-apb-uart";
-		reg = <0x0 0xfe690000 0x0 0x100>;
-		interrupts = <GIC_SPI 121 IRQ_TYPE_LEVEL_HIGH>;
-		clocks = <&cru SCLK_UART5>, <&cru PCLK_UART5>;
-		clock-names = "baudclk", "apb_pclk";
-		dmas = <&dmac0 10>, <&dmac0 11>;
-		pinctrl-0 = <&uart5m0_xfer>;
-		pinctrl-names = "default";
-		reg-io-width = <4>;
-		reg-shift = <2>;
-		status = "disabled";
-	};
-
-	uart6: serial@fe6a0000 {
-		compatible = "rockchip,rk3568-uart", "snps,dw-apb-uart";
-		reg = <0x0 0xfe6a0000 0x0 0x100>;
-		interrupts = <GIC_SPI 122 IRQ_TYPE_LEVEL_HIGH>;
-		clocks = <&cru SCLK_UART6>, <&cru PCLK_UART6>;
-		clock-names = "baudclk", "apb_pclk";
-		dmas = <&dmac0 12>, <&dmac0 13>;
-		pinctrl-0 = <&uart6m0_xfer>;
-		pinctrl-names = "default";
-		reg-io-width = <4>;
-		reg-shift = <2>;
-		status = "disabled";
-	};
-
-	uart7: serial@fe6b0000 {
-		compatible = "rockchip,rk3568-uart", "snps,dw-apb-uart";
-		reg = <0x0 0xfe6b0000 0x0 0x100>;
-		interrupts = <GIC_SPI 123 IRQ_TYPE_LEVEL_HIGH>;
-		clocks = <&cru SCLK_UART7>, <&cru PCLK_UART7>;
-		clock-names = "baudclk", "apb_pclk";
-		dmas = <&dmac0 14>, <&dmac0 15>;
-		pinctrl-0 = <&uart7m0_xfer>;
-		pinctrl-names = "default";
-		reg-io-width = <4>;
-		reg-shift = <2>;
-		status = "disabled";
-	};
-
-	uart8: serial@fe6c0000 {
-		compatible = "rockchip,rk3568-uart", "snps,dw-apb-uart";
-		reg = <0x0 0xfe6c0000 0x0 0x100>;
-		interrupts = <GIC_SPI 124 IRQ_TYPE_LEVEL_HIGH>;
-		clocks = <&cru SCLK_UART8>, <&cru PCLK_UART8>;
-		clock-names = "baudclk", "apb_pclk";
-		dmas = <&dmac0 16>, <&dmac0 17>;
-		pinctrl-0 = <&uart8m0_xfer>;
-		pinctrl-names = "default";
-		reg-io-width = <4>;
-		reg-shift = <2>;
-		status = "disabled";
-	};
-
-	uart9: serial@fe6d0000 {
-		compatible = "rockchip,rk3568-uart", "snps,dw-apb-uart";
-		reg = <0x0 0xfe6d0000 0x0 0x100>;
-		interrupts = <GIC_SPI 125 IRQ_TYPE_LEVEL_HIGH>;
-		clocks = <&cru SCLK_UART9>, <&cru PCLK_UART9>;
-		clock-names = "baudclk", "apb_pclk";
-		dmas = <&dmac0 18>, <&dmac0 19>;
-		pinctrl-0 = <&uart9m0_xfer>;
-		pinctrl-names = "default";
-		reg-io-width = <4>;
-		reg-shift = <2>;
-		status = "disabled";
+&cpu0_opp_table {
+	opp-1992000000 {
+		opp-hz = /bits/ 64 <1992000000>;
+		opp-microvolt = <1150000 1150000 1150000>;
 	};
+};
 
-	pinctrl: pinctrl {
-		compatible = "rockchip,rk3568-pinctrl";
-		rockchip,grf = <&grf>;
-		rockchip,pmu = <&pmugrf>;
-		#address-cells = <2>;
-		#size-cells = <2>;
-		ranges;
-
-		gpio0: gpio@fdd60000 {
-			compatible = "rockchip,gpio-bank";
-			reg = <0x0 0xfdd60000 0x0 0x100>;
-			interrupts = <GIC_SPI 33 IRQ_TYPE_LEVEL_HIGH>;
-			clocks = <&pmucru PCLK_GPIO0>;
-			gpio-controller;
-			#gpio-cells = <2>;
-			interrupt-controller;
-			#interrupt-cells = <2>;
-		};
-
-		gpio1: gpio@fe740000 {
-			compatible = "rockchip,gpio-bank";
-			reg = <0x0 0xfe740000 0x0 0x100>;
-			interrupts = <GIC_SPI 34 IRQ_TYPE_LEVEL_HIGH>;
-			clocks = <&cru PCLK_GPIO1>;
-			gpio-controller;
-			#gpio-cells = <2>;
-			interrupt-controller;
-			#interrupt-cells = <2>;
-		};
-
-		gpio2: gpio@fe750000 {
-			compatible = "rockchip,gpio-bank";
-			reg = <0x0 0xfe750000 0x0 0x100>;
-			interrupts = <GIC_SPI 35 IRQ_TYPE_LEVEL_HIGH>;
-			clocks = <&cru PCLK_GPIO2>;
-			gpio-controller;
-			#gpio-cells = <2>;
-			interrupt-controller;
-			#interrupt-cells = <2>;
-		};
-
-		gpio3: gpio@fe760000 {
-			compatible = "rockchip,gpio-bank";
-			reg = <0x0 0xfe760000 0x0 0x100>;
-			interrupts = <GIC_SPI 36 IRQ_TYPE_LEVEL_HIGH>;
-			clocks = <&cru PCLK_GPIO3>;
-			gpio-controller;
-			#gpio-cells = <2>;
-			interrupt-controller;
-			#interrupt-cells = <2>;
-		};
-
-		gpio4: gpio@fe770000 {
-			compatible = "rockchip,gpio-bank";
-			reg = <0x0 0xfe770000 0x0 0x100>;
-			interrupts = <GIC_SPI 37 IRQ_TYPE_LEVEL_HIGH>;
-			clocks = <&cru PCLK_GPIO4>;
-			gpio-controller;
-			#gpio-cells = <2>;
-			interrupt-controller;
-			#interrupt-cells = <2>;
-		};
+&power {
+	power-domain@RK3568_PD_PIPE {
+		reg = <RK3568_PD_PIPE>;
+		clocks = <&cru PCLK_PIPE>;
+		pm_qos = <&qos_pcie2x1>,
+			 <&qos_pcie3x1>,
+			 <&qos_pcie3x2>,
+			 <&qos_sata0>,
+			 <&qos_sata1>,
+			 <&qos_sata2>,
+			 <&qos_usb3_0>,
+			 <&qos_usb3_1>;
+		#power-domain-cells = <0>;
 	};
 };
-
-#include "rk3568-pinctrl.dtsi"
diff --git a/arch/arm64/boot/dts/rockchip/rk356x.dtsi b/arch/arm64/boot/dts/rockchip/rk356x.dtsi
new file mode 100644
index 000000000000..46d9552f6028
--- /dev/null
+++ b/arch/arm64/boot/dts/rockchip/rk356x.dtsi
@@ -0,0 +1,1145 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright (c) 2021 Rockchip Electronics Co., Ltd.
+ */
+
+#include <dt-bindings/clock/rk3568-cru.h>
+#include <dt-bindings/interrupt-controller/arm-gic.h>
+#include <dt-bindings/interrupt-controller/irq.h>
+#include <dt-bindings/phy/phy.h>
+#include <dt-bindings/pinctrl/rockchip.h>
+#include <dt-bindings/power/rk3568-power.h>
+#include <dt-bindings/soc/rockchip,boot-mode.h>
+#include <dt-bindings/thermal/thermal.h>
+
+/ {
+	interrupt-parent = <&gic>;
+	#address-cells = <2>;
+	#size-cells = <2>;
+
+	aliases {
+		gpio0 = &gpio0;
+		gpio1 = &gpio1;
+		gpio2 = &gpio2;
+		gpio3 = &gpio3;
+		gpio4 = &gpio4;
+		i2c0 = &i2c0;
+		i2c1 = &i2c1;
+		i2c2 = &i2c2;
+		i2c3 = &i2c3;
+		i2c4 = &i2c4;
+		i2c5 = &i2c5;
+		serial0 = &uart0;
+		serial1 = &uart1;
+		serial2 = &uart2;
+		serial3 = &uart3;
+		serial4 = &uart4;
+		serial5 = &uart5;
+		serial6 = &uart6;
+		serial7 = &uart7;
+		serial8 = &uart8;
+		serial9 = &uart9;
+	};
+
+	cpus {
+		#address-cells = <2>;
+		#size-cells = <0>;
+
+		cpu0: cpu@0 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a55";
+			reg = <0x0 0x0>;
+			clocks = <&scmi_clk 0>;
+			#cooling-cells = <2>;
+			enable-method = "psci";
+			operating-points-v2 = <&cpu0_opp_table>;
+		};
+
+		cpu1: cpu@100 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a55";
+			reg = <0x0 0x100>;
+			#cooling-cells = <2>;
+			enable-method = "psci";
+			operating-points-v2 = <&cpu0_opp_table>;
+		};
+
+		cpu2: cpu@200 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a55";
+			reg = <0x0 0x200>;
+			#cooling-cells = <2>;
+			enable-method = "psci";
+			operating-points-v2 = <&cpu0_opp_table>;
+		};
+
+		cpu3: cpu@300 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a55";
+			reg = <0x0 0x300>;
+			#cooling-cells = <2>;
+			enable-method = "psci";
+			operating-points-v2 = <&cpu0_opp_table>;
+		};
+	};
+
+	cpu0_opp_table: opp-table-0 {
+		compatible = "operating-points-v2";
+		opp-shared;
+
+		opp-408000000 {
+			opp-hz = /bits/ 64 <408000000>;
+			opp-microvolt = <900000 900000 1150000>;
+			clock-latency-ns = <40000>;
+		};
+
+		opp-600000000 {
+			opp-hz = /bits/ 64 <600000000>;
+			opp-microvolt = <900000 900000 1150000>;
+		};
+
+		opp-816000000 {
+			opp-hz = /bits/ 64 <816000000>;
+			opp-microvolt = <900000 900000 1150000>;
+			opp-suspend;
+		};
+
+		opp-1104000000 {
+			opp-hz = /bits/ 64 <1104000000>;
+			opp-microvolt = <900000 900000 1150000>;
+		};
+
+		opp-1416000000 {
+			opp-hz = /bits/ 64 <1416000000>;
+			opp-microvolt = <900000 900000 1150000>;
+		};
+
+		opp-1608000000 {
+			opp-hz = /bits/ 64 <1608000000>;
+			opp-microvolt = <975000 975000 1150000>;
+		};
+
+		opp-1800000000 {
+			opp-hz = /bits/ 64 <1800000000>;
+			opp-microvolt = <1050000 1050000 1150000>;
+		};
+	};
+
+	firmware {
+		scmi: scmi {
+			compatible = "arm,scmi-smc";
+			arm,smc-id = <0x82000010>;
+			shmem = <&scmi_shmem>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			scmi_clk: protocol@14 {
+				reg = <0x14>;
+				#clock-cells = <1>;
+			};
+		};
+	};
+
+	pmu {
+		compatible = "arm,cortex-a55-pmu";
+		interrupts = <GIC_SPI 228 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 229 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 230 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 231 IRQ_TYPE_LEVEL_HIGH>;
+		interrupt-affinity = <&cpu0>, <&cpu1>, <&cpu2>, <&cpu3>;
+	};
+
+	psci {
+		compatible = "arm,psci-1.0";
+		method = "smc";
+	};
+
+	timer {
+		compatible = "arm,armv8-timer";
+		interrupts = <GIC_PPI 13 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_PPI 14 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_PPI 11 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_PPI 10 IRQ_TYPE_LEVEL_HIGH>;
+		arm,no-tick-in-suspend;
+	};
+
+	xin24m: xin24m {
+		compatible = "fixed-clock";
+		clock-frequency = <24000000>;
+		clock-output-names = "xin24m";
+		#clock-cells = <0>;
+	};
+
+	xin32k: xin32k {
+		compatible = "fixed-clock";
+		clock-frequency = <32768>;
+		clock-output-names = "xin32k";
+		pinctrl-0 = <&clk32k_out0>;
+		pinctrl-names = "default";
+		#clock-cells = <0>;
+	};
+
+	sram@10f000 {
+		compatible = "mmio-sram";
+		reg = <0x0 0x0010f000 0x0 0x100>;
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges = <0 0x0 0x0010f000 0x100>;
+
+		scmi_shmem: sram@0 {
+			compatible = "arm,scmi-shmem";
+			reg = <0x0 0x100>;
+		};
+	};
+
+	gic: interrupt-controller@fd400000 {
+		compatible = "arm,gic-v3";
+		reg = <0x0 0xfd400000 0 0x10000>, /* GICD */
+		      <0x0 0xfd460000 0 0x80000>; /* GICR */
+		interrupts = <GIC_PPI 9 IRQ_TYPE_LEVEL_HIGH>;
+		interrupt-controller;
+		#interrupt-cells = <3>;
+		mbi-alias = <0x0 0xfd410000>;
+		mbi-ranges = <296 24>;
+		msi-controller;
+	};
+
+	pmugrf: syscon@fdc20000 {
+		compatible = "rockchip,rk3568-pmugrf", "syscon", "simple-mfd";
+		reg = <0x0 0xfdc20000 0x0 0x10000>;
+
+		pmu_io_domains: io-domains {
+			compatible = "rockchip,rk3568-pmu-io-voltage-domain";
+			status = "disabled";
+		};
+	};
+
+	grf: syscon@fdc60000 {
+		compatible = "rockchip,rk3568-grf", "syscon", "simple-mfd";
+		reg = <0x0 0xfdc60000 0x0 0x10000>;
+	};
+
+	pmucru: clock-controller@fdd00000 {
+		compatible = "rockchip,rk3568-pmucru";
+		reg = <0x0 0xfdd00000 0x0 0x1000>;
+		#clock-cells = <1>;
+		#reset-cells = <1>;
+	};
+
+	cru: clock-controller@fdd20000 {
+		compatible = "rockchip,rk3568-cru";
+		reg = <0x0 0xfdd20000 0x0 0x1000>;
+		#clock-cells = <1>;
+		#reset-cells = <1>;
+		assigned-clocks = <&cru PLL_GPLL>, <&pmucru PLL_PPLL>;
+		assigned-clock-rates = <1200000000>, <200000000>;
+		rockchip,grf = <&grf>;
+	};
+
+	i2c0: i2c@fdd40000 {
+		compatible = "rockchip,rk3568-i2c", "rockchip,rk3399-i2c";
+		reg = <0x0 0xfdd40000 0x0 0x1000>;
+		interrupts = <GIC_SPI 46 IRQ_TYPE_LEVEL_HIGH>;
+		clocks = <&pmucru CLK_I2C0>, <&pmucru PCLK_I2C0>;
+		clock-names = "i2c", "pclk";
+		pinctrl-0 = <&i2c0_xfer>;
+		pinctrl-names = "default";
+		#address-cells = <1>;
+		#size-cells = <0>;
+		status = "disabled";
+	};
+
+	uart0: serial@fdd50000 {
+		compatible = "rockchip,rk3568-uart", "snps,dw-apb-uart";
+		reg = <0x0 0xfdd50000 0x0 0x100>;
+		interrupts = <GIC_SPI 116 IRQ_TYPE_LEVEL_HIGH>;
+		clocks = <&pmucru SCLK_UART0>, <&pmucru PCLK_UART0>;
+		clock-names = "baudclk", "apb_pclk";
+		dmas = <&dmac0 0>, <&dmac0 1>;
+		pinctrl-0 = <&uart0_xfer>;
+		pinctrl-names = "default";
+		reg-io-width = <4>;
+		reg-shift = <2>;
+		status = "disabled";
+	};
+
+	pwm0: pwm@fdd70000 {
+		compatible = "rockchip,rk3568-pwm", "rockchip,rk3328-pwm";
+		reg = <0x0 0xfdd70000 0x0 0x10>;
+		clocks = <&pmucru CLK_PWM0>, <&pmucru PCLK_PWM0>;
+		clock-names = "pwm", "pclk";
+		pinctrl-0 = <&pwm0m0_pins>;
+		pinctrl-names = "active";
+		#pwm-cells = <3>;
+		status = "disabled";
+	};
+
+	pwm1: pwm@fdd70010 {
+		compatible = "rockchip,rk3568-pwm", "rockchip,rk3328-pwm";
+		reg = <0x0 0xfdd70010 0x0 0x10>;
+		clocks = <&pmucru CLK_PWM0>, <&pmucru PCLK_PWM0>;
+		clock-names = "pwm", "pclk";
+		pinctrl-0 = <&pwm1m0_pins>;
+		pinctrl-names = "active";
+		#pwm-cells = <3>;
+		status = "disabled";
+	};
+
+	pwm2: pwm@fdd70020 {
+		compatible = "rockchip,rk3568-pwm", "rockchip,rk3328-pwm";
+		reg = <0x0 0xfdd70020 0x0 0x10>;
+		clocks = <&pmucru CLK_PWM0>, <&pmucru PCLK_PWM0>;
+		clock-names = "pwm", "pclk";
+		pinctrl-0 = <&pwm2m0_pins>;
+		pinctrl-names = "active";
+		#pwm-cells = <3>;
+		status = "disabled";
+	};
+
+	pwm3: pwm@fdd70030 {
+		compatible = "rockchip,rk3568-pwm", "rockchip,rk3328-pwm";
+		reg = <0x0 0xfdd70030 0x0 0x10>;
+		clocks = <&pmucru CLK_PWM0>, <&pmucru PCLK_PWM0>;
+		clock-names = "pwm", "pclk";
+		pinctrl-0 = <&pwm3_pins>;
+		pinctrl-names = "active";
+		#pwm-cells = <3>;
+		status = "disabled";
+	};
+
+	pmu: power-management@fdd90000 {
+		compatible = "rockchip,rk3568-pmu", "syscon", "simple-mfd";
+		reg = <0x0 0xfdd90000 0x0 0x1000>;
+
+		power: power-controller {
+			compatible = "rockchip,rk3568-power-controller";
+			#power-domain-cells = <1>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			/* These power domains are grouped by VD_GPU */
+			power-domain@RK3568_PD_GPU {
+				reg = <RK3568_PD_GPU>;
+				clocks = <&cru ACLK_GPU_PRE>,
+					 <&cru PCLK_GPU_PRE>;
+				pm_qos = <&qos_gpu>;
+				#power-domain-cells = <0>;
+			};
+
+			/* These power domains are grouped by VD_LOGIC */
+			power-domain@RK3568_PD_VI {
+				reg = <RK3568_PD_VI>;
+				clocks = <&cru HCLK_VI>,
+					 <&cru PCLK_VI>;
+				pm_qos = <&qos_isp>,
+					 <&qos_vicap0>,
+					 <&qos_vicap1>;
+				#power-domain-cells = <0>;
+			};
+
+			power-domain@RK3568_PD_VO {
+				reg = <RK3568_PD_VO>;
+				clocks = <&cru HCLK_VO>,
+					 <&cru PCLK_VO>,
+					 <&cru ACLK_VOP_PRE>;
+				pm_qos = <&qos_hdcp>,
+					 <&qos_vop_m0>,
+					 <&qos_vop_m1>;
+				#power-domain-cells = <0>;
+			};
+
+			power-domain@RK3568_PD_RGA {
+				reg = <RK3568_PD_RGA>;
+				clocks = <&cru HCLK_RGA_PRE>,
+					 <&cru PCLK_RGA_PRE>;
+				pm_qos = <&qos_ebc>,
+					 <&qos_iep>,
+					 <&qos_jpeg_dec>,
+					 <&qos_jpeg_enc>,
+					 <&qos_rga_rd>,
+					 <&qos_rga_wr>;
+				#power-domain-cells = <0>;
+			};
+
+			power-domain@RK3568_PD_VPU {
+				reg = <RK3568_PD_VPU>;
+				clocks = <&cru HCLK_VPU_PRE>;
+				pm_qos = <&qos_vpu>;
+				#power-domain-cells = <0>;
+			};
+
+			power-domain@RK3568_PD_RKVDEC {
+				clocks = <&cru HCLK_RKVDEC_PRE>;
+				reg = <RK3568_PD_RKVDEC>;
+				pm_qos = <&qos_rkvdec>;
+				#power-domain-cells = <0>;
+			};
+
+			power-domain@RK3568_PD_RKVENC {
+				reg = <RK3568_PD_RKVENC>;
+				clocks = <&cru HCLK_RKVENC_PRE>;
+				pm_qos = <&qos_rkvenc_rd_m0>,
+					 <&qos_rkvenc_rd_m1>,
+					 <&qos_rkvenc_wr_m0>;
+				#power-domain-cells = <0>;
+			};
+		};
+	};
+
+	sdmmc2: mmc@fe000000 {
+		compatible = "rockchip,rk3568-dw-mshc", "rockchip,rk3288-dw-mshc";
+		reg = <0x0 0xfe000000 0x0 0x4000>;
+		interrupts = <GIC_SPI 100 IRQ_TYPE_LEVEL_HIGH>;
+		clocks = <&cru HCLK_SDMMC2>, <&cru CLK_SDMMC2>,
+			 <&cru SCLK_SDMMC2_DRV>, <&cru SCLK_SDMMC2_SAMPLE>;
+		clock-names = "biu", "ciu", "ciu-drive", "ciu-sample";
+		fifo-depth = <0x100>;
+		max-frequency = <150000000>;
+		resets = <&cru SRST_SDMMC2>;
+		reset-names = "reset";
+		status = "disabled";
+	};
+
+	gmac1: ethernet@fe010000 {
+		compatible = "rockchip,rk3568-gmac", "snps,dwmac-4.20a";
+		reg = <0x0 0xfe010000 0x0 0x10000>;
+		interrupts = <GIC_SPI 32 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 29 IRQ_TYPE_LEVEL_HIGH>;
+		interrupt-names = "macirq", "eth_wake_irq";
+		clocks = <&cru SCLK_GMAC1>, <&cru SCLK_GMAC1_RX_TX>,
+			 <&cru SCLK_GMAC1_RX_TX>, <&cru CLK_MAC1_REFOUT>,
+			 <&cru ACLK_GMAC1>, <&cru PCLK_GMAC1>,
+			 <&cru SCLK_GMAC1_RX_TX>, <&cru CLK_GMAC1_PTP_REF>;
+		clock-names = "stmmaceth", "mac_clk_rx",
+			      "mac_clk_tx", "clk_mac_refout",
+			      "aclk_mac", "pclk_mac",
+			      "clk_mac_speed", "ptp_ref";
+		resets = <&cru SRST_A_GMAC1>;
+		reset-names = "stmmaceth";
+		rockchip,grf = <&grf>;
+		snps,axi-config = <&gmac1_stmmac_axi_setup>;
+		snps,mixed-burst;
+		snps,mtl-rx-config = <&gmac1_mtl_rx_setup>;
+		snps,mtl-tx-config = <&gmac1_mtl_tx_setup>;
+		snps,tso;
+		status = "disabled";
+
+		mdio1: mdio {
+			compatible = "snps,dwmac-mdio";
+			#address-cells = <0x1>;
+			#size-cells = <0x0>;
+		};
+
+		gmac1_stmmac_axi_setup: stmmac-axi-config {
+			snps,blen = <0 0 0 0 16 8 4>;
+			snps,rd_osr_lmt = <8>;
+			snps,wr_osr_lmt = <4>;
+		};
+
+		gmac1_mtl_rx_setup: rx-queues-config {
+			snps,rx-queues-to-use = <1>;
+			queue0 {};
+		};
+
+		gmac1_mtl_tx_setup: tx-queues-config {
+			snps,tx-queues-to-use = <1>;
+			queue0 {};
+		};
+	};
+
+	qos_gpu: qos@fe128000 {
+		compatible = "rockchip,rk3568-qos", "syscon";
+		reg = <0x0 0xfe128000 0x0 0x20>;
+	};
+
+	qos_rkvenc_rd_m0: qos@fe138080 {
+		compatible = "rockchip,rk3568-qos", "syscon";
+		reg = <0x0 0xfe138080 0x0 0x20>;
+	};
+
+	qos_rkvenc_rd_m1: qos@fe138100 {
+		compatible = "rockchip,rk3568-qos", "syscon";
+		reg = <0x0 0xfe138100 0x0 0x20>;
+	};
+
+	qos_rkvenc_wr_m0: qos@fe138180 {
+		compatible = "rockchip,rk3568-qos", "syscon";
+		reg = <0x0 0xfe138180 0x0 0x20>;
+	};
+
+	qos_isp: qos@fe148000 {
+		compatible = "rockchip,rk3568-qos", "syscon";
+		reg = <0x0 0xfe148000 0x0 0x20>;
+	};
+
+	qos_vicap0: qos@fe148080 {
+		compatible = "rockchip,rk3568-qos", "syscon";
+		reg = <0x0 0xfe148080 0x0 0x20>;
+	};
+
+	qos_vicap1: qos@fe148100 {
+		compatible = "rockchip,rk3568-qos", "syscon";
+		reg = <0x0 0xfe148100 0x0 0x20>;
+	};
+
+	qos_vpu: qos@fe150000 {
+		compatible = "rockchip,rk3568-qos", "syscon";
+		reg = <0x0 0xfe150000 0x0 0x20>;
+	};
+
+	qos_ebc: qos@fe158000 {
+		compatible = "rockchip,rk3568-qos", "syscon";
+		reg = <0x0 0xfe158000 0x0 0x20>;
+	};
+
+	qos_iep: qos@fe158100 {
+		compatible = "rockchip,rk3568-qos", "syscon";
+		reg = <0x0 0xfe158100 0x0 0x20>;
+	};
+
+	qos_jpeg_dec: qos@fe158180 {
+		compatible = "rockchip,rk3568-qos", "syscon";
+		reg = <0x0 0xfe158180 0x0 0x20>;
+	};
+
+	qos_jpeg_enc: qos@fe158200 {
+		compatible = "rockchip,rk3568-qos", "syscon";
+		reg = <0x0 0xfe158200 0x0 0x20>;
+	};
+
+	qos_rga_rd: qos@fe158280 {
+		compatible = "rockchip,rk3568-qos", "syscon";
+		reg = <0x0 0xfe158280 0x0 0x20>;
+	};
+
+	qos_rga_wr: qos@fe158300 {
+		compatible = "rockchip,rk3568-qos", "syscon";
+		reg = <0x0 0xfe158300 0x0 0x20>;
+	};
+
+	qos_npu: qos@fe180000 {
+		compatible = "rockchip,rk3568-qos", "syscon";
+		reg = <0x0 0xfe180000 0x0 0x20>;
+	};
+
+	qos_pcie2x1: qos@fe190000 {
+		compatible = "rockchip,rk3568-qos", "syscon";
+		reg = <0x0 0xfe190000 0x0 0x20>;
+	};
+
+	qos_sata1: qos@fe190280 {
+		compatible = "rockchip,rk3568-qos", "syscon";
+		reg = <0x0 0xfe190280 0x0 0x20>;
+	};
+
+	qos_sata2: qos@fe190300 {
+		compatible = "rockchip,rk3568-qos", "syscon";
+		reg = <0x0 0xfe190300 0x0 0x20>;
+	};
+
+	qos_usb3_0: qos@fe190380 {
+		compatible = "rockchip,rk3568-qos", "syscon";
+		reg = <0x0 0xfe190380 0x0 0x20>;
+	};
+
+	qos_usb3_1: qos@fe190400 {
+		compatible = "rockchip,rk3568-qos", "syscon";
+		reg = <0x0 0xfe190400 0x0 0x20>;
+	};
+
+	qos_rkvdec: qos@fe198000 {
+		compatible = "rockchip,rk3568-qos", "syscon";
+		reg = <0x0 0xfe198000 0x0 0x20>;
+	};
+
+	qos_hdcp: qos@fe1a8000 {
+		compatible = "rockchip,rk3568-qos", "syscon";
+		reg = <0x0 0xfe1a8000 0x0 0x20>;
+	};
+
+	qos_vop_m0: qos@fe1a8080 {
+		compatible = "rockchip,rk3568-qos", "syscon";
+		reg = <0x0 0xfe1a8080 0x0 0x20>;
+	};
+
+	qos_vop_m1: qos@fe1a8100 {
+		compatible = "rockchip,rk3568-qos", "syscon";
+		reg = <0x0 0xfe1a8100 0x0 0x20>;
+	};
+
+	sdmmc0: mmc@fe2b0000 {
+		compatible = "rockchip,rk3568-dw-mshc", "rockchip,rk3288-dw-mshc";
+		reg = <0x0 0xfe2b0000 0x0 0x4000>;
+		interrupts = <GIC_SPI 98 IRQ_TYPE_LEVEL_HIGH>;
+		clocks = <&cru HCLK_SDMMC0>, <&cru CLK_SDMMC0>,
+			 <&cru SCLK_SDMMC0_DRV>, <&cru SCLK_SDMMC0_SAMPLE>;
+		clock-names = "biu", "ciu", "ciu-drive", "ciu-sample";
+		fifo-depth = <0x100>;
+		max-frequency = <150000000>;
+		resets = <&cru SRST_SDMMC0>;
+		reset-names = "reset";
+		status = "disabled";
+	};
+
+	sdmmc1: mmc@fe2c0000 {
+		compatible = "rockchip,rk3568-dw-mshc", "rockchip,rk3288-dw-mshc";
+		reg = <0x0 0xfe2c0000 0x0 0x4000>;
+		interrupts = <GIC_SPI 99 IRQ_TYPE_LEVEL_HIGH>;
+		clocks = <&cru HCLK_SDMMC1>, <&cru CLK_SDMMC1>,
+			 <&cru SCLK_SDMMC1_DRV>, <&cru SCLK_SDMMC1_SAMPLE>;
+		clock-names = "biu", "ciu", "ciu-drive", "ciu-sample";
+		fifo-depth = <0x100>;
+		max-frequency = <150000000>;
+		resets = <&cru SRST_SDMMC1>;
+		reset-names = "reset";
+		status = "disabled";
+	};
+
+	sdhci: mmc@fe310000 {
+		compatible = "rockchip,rk3568-dwcmshc";
+		reg = <0x0 0xfe310000 0x0 0x10000>;
+		interrupts = <GIC_SPI 19 IRQ_TYPE_LEVEL_HIGH>;
+		assigned-clocks = <&cru BCLK_EMMC>, <&cru TCLK_EMMC>;
+		assigned-clock-rates = <200000000>, <24000000>;
+		clocks = <&cru CCLK_EMMC>, <&cru HCLK_EMMC>,
+			 <&cru ACLK_EMMC>, <&cru BCLK_EMMC>,
+			 <&cru TCLK_EMMC>;
+		clock-names = "core", "bus", "axi", "block", "timer";
+		status = "disabled";
+	};
+
+	spdif: spdif@fe460000 {
+		compatible = "rockchip,rk3568-spdif";
+		reg = <0x0 0xfe460000 0x0 0x1000>;
+		interrupts = <GIC_SPI 102 IRQ_TYPE_LEVEL_HIGH>;
+		clock-names = "mclk", "hclk";
+		clocks = <&cru MCLK_SPDIF_8CH>, <&cru HCLK_SPDIF_8CH>;
+		dmas = <&dmac1 1>;
+		dma-names = "tx";
+		pinctrl-names = "default";
+		pinctrl-0 = <&spdifm0_tx>;
+		#sound-dai-cells = <0>;
+		status = "disabled";
+	};
+
+	i2s1_8ch: i2s@fe410000 {
+		compatible = "rockchip,rk3568-i2s-tdm";
+		reg = <0x0 0xfe410000 0x0 0x1000>;
+		interrupts = <GIC_SPI 53 IRQ_TYPE_LEVEL_HIGH>;
+		assigned-clocks = <&cru CLK_I2S1_8CH_TX_SRC>, <&cru CLK_I2S1_8CH_RX_SRC>;
+		assigned-clock-rates = <1188000000>, <1188000000>;
+		clocks = <&cru MCLK_I2S1_8CH_TX>, <&cru MCLK_I2S1_8CH_RX>,
+			 <&cru HCLK_I2S1_8CH>;
+		clock-names = "mclk_tx", "mclk_rx", "hclk";
+		dmas = <&dmac1 3>, <&dmac1 2>;
+		dma-names = "rx", "tx";
+		resets = <&cru SRST_M_I2S1_8CH_TX>, <&cru SRST_M_I2S1_8CH_RX>;
+		reset-names = "tx-m", "rx-m";
+		rockchip,grf = <&grf>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&i2s1m0_sclktx &i2s1m0_sclkrx
+			     &i2s1m0_lrcktx &i2s1m0_lrckrx
+			     &i2s1m0_sdi0   &i2s1m0_sdi1
+			     &i2s1m0_sdi2   &i2s1m0_sdi3
+			     &i2s1m0_sdo0   &i2s1m0_sdo1
+			     &i2s1m0_sdo2   &i2s1m0_sdo3>;
+		#sound-dai-cells = <0>;
+		status = "disabled";
+	};
+
+	dmac0: dmac@fe530000 {
+		compatible = "arm,pl330", "arm,primecell";
+		reg = <0x0 0xfe530000 0x0 0x4000>;
+		interrupts = <GIC_SPI 14 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 13 IRQ_TYPE_LEVEL_HIGH>;
+		arm,pl330-periph-burst;
+		clocks = <&cru ACLK_BUS>;
+		clock-names = "apb_pclk";
+		#dma-cells = <1>;
+	};
+
+	dmac1: dmac@fe550000 {
+		compatible = "arm,pl330", "arm,primecell";
+		reg = <0x0 0xfe550000 0x0 0x4000>;
+		interrupts = <GIC_SPI 16 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 15 IRQ_TYPE_LEVEL_HIGH>;
+		arm,pl330-periph-burst;
+		clocks = <&cru ACLK_BUS>;
+		clock-names = "apb_pclk";
+		#dma-cells = <1>;
+	};
+
+	i2c1: i2c@fe5a0000 {
+		compatible = "rockchip,rk3568-i2c", "rockchip,rk3399-i2c";
+		reg = <0x0 0xfe5a0000 0x0 0x1000>;
+		interrupts = <GIC_SPI 47 IRQ_TYPE_LEVEL_HIGH>;
+		clocks = <&cru CLK_I2C1>, <&cru PCLK_I2C1>;
+		clock-names = "i2c", "pclk";
+		pinctrl-0 = <&i2c1_xfer>;
+		pinctrl-names = "default";
+		#address-cells = <1>;
+		#size-cells = <0>;
+		status = "disabled";
+	};
+
+	i2c2: i2c@fe5b0000 {
+		compatible = "rockchip,rk3568-i2c", "rockchip,rk3399-i2c";
+		reg = <0x0 0xfe5b0000 0x0 0x1000>;
+		interrupts = <GIC_SPI 48 IRQ_TYPE_LEVEL_HIGH>;
+		clocks = <&cru CLK_I2C2>, <&cru PCLK_I2C2>;
+		clock-names = "i2c", "pclk";
+		pinctrl-0 = <&i2c2m0_xfer>;
+		pinctrl-names = "default";
+		#address-cells = <1>;
+		#size-cells = <0>;
+		status = "disabled";
+	};
+
+	i2c3: i2c@fe5c0000 {
+		compatible = "rockchip,rk3568-i2c", "rockchip,rk3399-i2c";
+		reg = <0x0 0xfe5c0000 0x0 0x1000>;
+		interrupts = <GIC_SPI 49 IRQ_TYPE_LEVEL_HIGH>;
+		clocks = <&cru CLK_I2C3>, <&cru PCLK_I2C3>;
+		clock-names = "i2c", "pclk";
+		pinctrl-0 = <&i2c3m0_xfer>;
+		pinctrl-names = "default";
+		#address-cells = <1>;
+		#size-cells = <0>;
+		status = "disabled";
+	};
+
+	i2c4: i2c@fe5d0000 {
+		compatible = "rockchip,rk3568-i2c", "rockchip,rk3399-i2c";
+		reg = <0x0 0xfe5d0000 0x0 0x1000>;
+		interrupts = <GIC_SPI 50 IRQ_TYPE_LEVEL_HIGH>;
+		clocks = <&cru CLK_I2C4>, <&cru PCLK_I2C4>;
+		clock-names = "i2c", "pclk";
+		pinctrl-0 = <&i2c4m0_xfer>;
+		pinctrl-names = "default";
+		#address-cells = <1>;
+		#size-cells = <0>;
+		status = "disabled";
+	};
+
+	i2c5: i2c@fe5e0000 {
+		compatible = "rockchip,rk3568-i2c", "rockchip,rk3399-i2c";
+		reg = <0x0 0xfe5e0000 0x0 0x1000>;
+		interrupts = <GIC_SPI 51 IRQ_TYPE_LEVEL_HIGH>;
+		clocks = <&cru CLK_I2C5>, <&cru PCLK_I2C5>;
+		clock-names = "i2c", "pclk";
+		pinctrl-0 = <&i2c5m0_xfer>;
+		pinctrl-names = "default";
+		#address-cells = <1>;
+		#size-cells = <0>;
+		status = "disabled";
+	};
+
+	wdt: watchdog@fe600000 {
+		compatible = "rockchip,rk3568-wdt", "snps,dw-wdt";
+		reg = <0x0 0xfe600000 0x0 0x100>;
+		interrupts = <GIC_SPI 149 IRQ_TYPE_LEVEL_HIGH>;
+		clocks = <&cru TCLK_WDT_NS>, <&cru PCLK_WDT_NS>;
+		clock-names = "tclk", "pclk";
+	};
+
+	uart1: serial@fe650000 {
+		compatible = "rockchip,rk3568-uart", "snps,dw-apb-uart";
+		reg = <0x0 0xfe650000 0x0 0x100>;
+		interrupts = <GIC_SPI 117 IRQ_TYPE_LEVEL_HIGH>;
+		clocks = <&cru SCLK_UART1>, <&cru PCLK_UART1>;
+		clock-names = "baudclk", "apb_pclk";
+		dmas = <&dmac0 2>, <&dmac0 3>;
+		pinctrl-0 = <&uart1m0_xfer>;
+		pinctrl-names = "default";
+		reg-io-width = <4>;
+		reg-shift = <2>;
+		status = "disabled";
+	};
+
+	uart2: serial@fe660000 {
+		compatible = "rockchip,rk3568-uart", "snps,dw-apb-uart";
+		reg = <0x0 0xfe660000 0x0 0x100>;
+		interrupts = <GIC_SPI 118 IRQ_TYPE_LEVEL_HIGH>;
+		clocks = <&cru SCLK_UART2>, <&cru PCLK_UART2>;
+		clock-names = "baudclk", "apb_pclk";
+		dmas = <&dmac0 4>, <&dmac0 5>;
+		pinctrl-0 = <&uart2m0_xfer>;
+		pinctrl-names = "default";
+		reg-io-width = <4>;
+		reg-shift = <2>;
+		status = "disabled";
+	};
+
+	uart3: serial@fe670000 {
+		compatible = "rockchip,rk3568-uart", "snps,dw-apb-uart";
+		reg = <0x0 0xfe670000 0x0 0x100>;
+		interrupts = <GIC_SPI 119 IRQ_TYPE_LEVEL_HIGH>;
+		clocks = <&cru SCLK_UART3>, <&cru PCLK_UART3>;
+		clock-names = "baudclk", "apb_pclk";
+		dmas = <&dmac0 6>, <&dmac0 7>;
+		pinctrl-0 = <&uart3m0_xfer>;
+		pinctrl-names = "default";
+		reg-io-width = <4>;
+		reg-shift = <2>;
+		status = "disabled";
+	};
+
+	uart4: serial@fe680000 {
+		compatible = "rockchip,rk3568-uart", "snps,dw-apb-uart";
+		reg = <0x0 0xfe680000 0x0 0x100>;
+		interrupts = <GIC_SPI 120 IRQ_TYPE_LEVEL_HIGH>;
+		clocks = <&cru SCLK_UART4>, <&cru PCLK_UART4>;
+		clock-names = "baudclk", "apb_pclk";
+		dmas = <&dmac0 8>, <&dmac0 9>;
+		pinctrl-0 = <&uart4m0_xfer>;
+		pinctrl-names = "default";
+		reg-io-width = <4>;
+		reg-shift = <2>;
+		status = "disabled";
+	};
+
+	uart5: serial@fe690000 {
+		compatible = "rockchip,rk3568-uart", "snps,dw-apb-uart";
+		reg = <0x0 0xfe690000 0x0 0x100>;
+		interrupts = <GIC_SPI 121 IRQ_TYPE_LEVEL_HIGH>;
+		clocks = <&cru SCLK_UART5>, <&cru PCLK_UART5>;
+		clock-names = "baudclk", "apb_pclk";
+		dmas = <&dmac0 10>, <&dmac0 11>;
+		pinctrl-0 = <&uart5m0_xfer>;
+		pinctrl-names = "default";
+		reg-io-width = <4>;
+		reg-shift = <2>;
+		status = "disabled";
+	};
+
+	uart6: serial@fe6a0000 {
+		compatible = "rockchip,rk3568-uart", "snps,dw-apb-uart";
+		reg = <0x0 0xfe6a0000 0x0 0x100>;
+		interrupts = <GIC_SPI 122 IRQ_TYPE_LEVEL_HIGH>;
+		clocks = <&cru SCLK_UART6>, <&cru PCLK_UART6>;
+		clock-names = "baudclk", "apb_pclk";
+		dmas = <&dmac0 12>, <&dmac0 13>;
+		pinctrl-0 = <&uart6m0_xfer>;
+		pinctrl-names = "default";
+		reg-io-width = <4>;
+		reg-shift = <2>;
+		status = "disabled";
+	};
+
+	uart7: serial@fe6b0000 {
+		compatible = "rockchip,rk3568-uart", "snps,dw-apb-uart";
+		reg = <0x0 0xfe6b0000 0x0 0x100>;
+		interrupts = <GIC_SPI 123 IRQ_TYPE_LEVEL_HIGH>;
+		clocks = <&cru SCLK_UART7>, <&cru PCLK_UART7>;
+		clock-names = "baudclk", "apb_pclk";
+		dmas = <&dmac0 14>, <&dmac0 15>;
+		pinctrl-0 = <&uart7m0_xfer>;
+		pinctrl-names = "default";
+		reg-io-width = <4>;
+		reg-shift = <2>;
+		status = "disabled";
+	};
+
+	uart8: serial@fe6c0000 {
+		compatible = "rockchip,rk3568-uart", "snps,dw-apb-uart";
+		reg = <0x0 0xfe6c0000 0x0 0x100>;
+		interrupts = <GIC_SPI 124 IRQ_TYPE_LEVEL_HIGH>;
+		clocks = <&cru SCLK_UART8>, <&cru PCLK_UART8>;
+		clock-names = "baudclk", "apb_pclk";
+		dmas = <&dmac0 16>, <&dmac0 17>;
+		pinctrl-0 = <&uart8m0_xfer>;
+		pinctrl-names = "default";
+		reg-io-width = <4>;
+		reg-shift = <2>;
+		status = "disabled";
+	};
+
+	uart9: serial@fe6d0000 {
+		compatible = "rockchip,rk3568-uart", "snps,dw-apb-uart";
+		reg = <0x0 0xfe6d0000 0x0 0x100>;
+		interrupts = <GIC_SPI 125 IRQ_TYPE_LEVEL_HIGH>;
+		clocks = <&cru SCLK_UART9>, <&cru PCLK_UART9>;
+		clock-names = "baudclk", "apb_pclk";
+		dmas = <&dmac0 18>, <&dmac0 19>;
+		pinctrl-0 = <&uart9m0_xfer>;
+		pinctrl-names = "default";
+		reg-io-width = <4>;
+		reg-shift = <2>;
+		status = "disabled";
+	};
+
+	thermal_zones: thermal-zones {
+		cpu_thermal: cpu-thermal {
+			polling-delay-passive = <100>;
+			polling-delay = <1000>;
+
+			thermal-sensors = <&tsadc 0>;
+
+			trips {
+				cpu_alert0: cpu_alert0 {
+					temperature = <70000>;
+					hysteresis = <2000>;
+					type = "passive";
+				};
+				cpu_alert1: cpu_alert1 {
+					temperature = <75000>;
+					hysteresis = <2000>;
+					type = "passive";
+				};
+				cpu_crit: cpu_crit {
+					temperature = <95000>;
+					hysteresis = <2000>;
+					type = "critical";
+				};
+			};
+
+			cooling-maps {
+				map0 {
+					trip = <&cpu_alert0>;
+					cooling-device =
+						<&cpu0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+						<&cpu1 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+						<&cpu2 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+						<&cpu3 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
+				};
+			};
+		};
+
+		gpu_thermal: gpu-thermal {
+			polling-delay-passive = <20>; /* milliseconds */
+			polling-delay = <1000>; /* milliseconds */
+
+			thermal-sensors = <&tsadc 1>;
+		};
+	};
+
+	tsadc: tsadc@fe710000 {
+		compatible = "rockchip,rk3568-tsadc";
+		reg = <0x0 0xfe710000 0x0 0x100>;
+		interrupts = <GIC_SPI 115 IRQ_TYPE_LEVEL_HIGH>;
+		assigned-clocks = <&cru CLK_TSADC_TSEN>, <&cru CLK_TSADC>;
+		assigned-clock-rates = <17000000>, <700000>;
+		clocks = <&cru CLK_TSADC>, <&cru PCLK_TSADC>;
+		clock-names = "tsadc", "apb_pclk";
+		resets = <&cru SRST_P_TSADC>, <&cru SRST_TSADC>,
+			 <&cru SRST_TSADCPHY>;
+		rockchip,grf = <&grf>;
+		rockchip,hw-tshut-temp = <95000>;
+		pinctrl-names = "init", "default", "sleep";
+		pinctrl-0 = <&tsadc_pin>;
+		pinctrl-1 = <&tsadc_shutorg>;
+		pinctrl-2 = <&tsadc_pin>;
+		#thermal-sensor-cells = <1>;
+		status = "disabled";
+	};
+
+	saradc: saradc@fe720000 {
+		compatible = "rockchip,rk3568-saradc", "rockchip,rk3399-saradc";
+		reg = <0x0 0xfe720000 0x0 0x100>;
+		interrupts = <GIC_SPI 93 IRQ_TYPE_LEVEL_HIGH>;
+		clocks = <&cru CLK_SARADC>, <&cru PCLK_SARADC>;
+		clock-names = "saradc", "apb_pclk";
+		resets = <&cru SRST_P_SARADC>;
+		reset-names = "saradc-apb";
+		#io-channel-cells = <1>;
+		status = "disabled";
+	};
+
+	pwm4: pwm@fe6e0000 {
+		compatible = "rockchip,rk3568-pwm", "rockchip,rk3328-pwm";
+		reg = <0x0 0xfe6e0000 0x0 0x10>;
+		clocks = <&cru CLK_PWM1>, <&cru PCLK_PWM1>;
+		clock-names = "pwm", "pclk";
+		pinctrl-0 = <&pwm4_pins>;
+		pinctrl-names = "active";
+		#pwm-cells = <3>;
+		status = "disabled";
+	};
+
+	pwm5: pwm@fe6e0010 {
+		compatible = "rockchip,rk3568-pwm", "rockchip,rk3328-pwm";
+		reg = <0x0 0xfe6e0010 0x0 0x10>;
+		clocks = <&cru CLK_PWM1>, <&cru PCLK_PWM1>;
+		clock-names = "pwm", "pclk";
+		pinctrl-0 = <&pwm5_pins>;
+		pinctrl-names = "active";
+		#pwm-cells = <3>;
+		status = "disabled";
+	};
+
+	pwm6: pwm@fe6e0020 {
+		compatible = "rockchip,rk3568-pwm", "rockchip,rk3328-pwm";
+		reg = <0x0 0xfe6e0020 0x0 0x10>;
+		clocks = <&cru CLK_PWM1>, <&cru PCLK_PWM1>;
+		clock-names = "pwm", "pclk";
+		pinctrl-0 = <&pwm6_pins>;
+		pinctrl-names = "active";
+		#pwm-cells = <3>;
+		status = "disabled";
+	};
+
+	pwm7: pwm@fe6e0030 {
+		compatible = "rockchip,rk3568-pwm", "rockchip,rk3328-pwm";
+		reg = <0x0 0xfe6e0030 0x0 0x10>;
+		clocks = <&cru CLK_PWM1>, <&cru PCLK_PWM1>;
+		clock-names = "pwm", "pclk";
+		pinctrl-0 = <&pwm7_pins>;
+		pinctrl-names = "active";
+		#pwm-cells = <3>;
+		status = "disabled";
+	};
+
+	pwm8: pwm@fe6f0000 {
+		compatible = "rockchip,rk3568-pwm", "rockchip,rk3328-pwm";
+		reg = <0x0 0xfe6f0000 0x0 0x10>;
+		clocks = <&cru CLK_PWM2>, <&cru PCLK_PWM2>;
+		clock-names = "pwm", "pclk";
+		pinctrl-0 = <&pwm8m0_pins>;
+		pinctrl-names = "active";
+		#pwm-cells = <3>;
+		status = "disabled";
+	};
+
+	pwm9: pwm@fe6f0010 {
+		compatible = "rockchip,rk3568-pwm", "rockchip,rk3328-pwm";
+		reg = <0x0 0xfe6f0010 0x0 0x10>;
+		clocks = <&cru CLK_PWM2>, <&cru PCLK_PWM2>;
+		clock-names = "pwm", "pclk";
+		pinctrl-0 = <&pwm9m0_pins>;
+		pinctrl-names = "active";
+		#pwm-cells = <3>;
+		status = "disabled";
+	};
+
+	pwm10: pwm@fe6f0020 {
+		compatible = "rockchip,rk3568-pwm", "rockchip,rk3328-pwm";
+		reg = <0x0 0xfe6f0020 0x0 0x10>;
+		clocks = <&cru CLK_PWM2>, <&cru PCLK_PWM2>;
+		clock-names = "pwm", "pclk";
+		pinctrl-0 = <&pwm10m0_pins>;
+		pinctrl-names = "active";
+		#pwm-cells = <3>;
+		status = "disabled";
+	};
+
+	pwm11: pwm@fe6f0030 {
+		compatible = "rockchip,rk3568-pwm", "rockchip,rk3328-pwm";
+		reg = <0x0 0xfe6f0030 0x0 0x10>;
+		clocks = <&cru CLK_PWM2>, <&cru PCLK_PWM2>;
+		clock-names = "pwm", "pclk";
+		pinctrl-0 = <&pwm11m0_pins>;
+		pinctrl-names = "active";
+		#pwm-cells = <3>;
+		status = "disabled";
+	};
+
+	pwm12: pwm@fe700000 {
+		compatible = "rockchip,rk3568-pwm", "rockchip,rk3328-pwm";
+		reg = <0x0 0xfe700000 0x0 0x10>;
+		clocks = <&cru CLK_PWM3>, <&cru PCLK_PWM3>;
+		clock-names = "pwm", "pclk";
+		pinctrl-0 = <&pwm12m0_pins>;
+		pinctrl-names = "active";
+		#pwm-cells = <3>;
+		status = "disabled";
+	};
+
+	pwm13: pwm@fe700010 {
+		compatible = "rockchip,rk3568-pwm", "rockchip,rk3328-pwm";
+		reg = <0x0 0xfe700010 0x0 0x10>;
+		clocks = <&cru CLK_PWM3>, <&cru PCLK_PWM3>;
+		clock-names = "pwm", "pclk";
+		pinctrl-0 = <&pwm13m0_pins>;
+		pinctrl-names = "active";
+		#pwm-cells = <3>;
+		status = "disabled";
+	};
+
+	pwm14: pwm@fe700020 {
+		compatible = "rockchip,rk3568-pwm", "rockchip,rk3328-pwm";
+		reg = <0x0 0xfe700020 0x0 0x10>;
+		clocks = <&cru CLK_PWM3>, <&cru PCLK_PWM3>;
+		clock-names = "pwm", "pclk";
+		pinctrl-0 = <&pwm14m0_pins>;
+		pinctrl-names = "active";
+		#pwm-cells = <3>;
+		status = "disabled";
+	};
+
+	pwm15: pwm@fe700030 {
+		compatible = "rockchip,rk3568-pwm", "rockchip,rk3328-pwm";
+		reg = <0x0 0xfe700030 0x0 0x10>;
+		clocks = <&cru CLK_PWM3>, <&cru PCLK_PWM3>;
+		clock-names = "pwm", "pclk";
+		pinctrl-0 = <&pwm15m0_pins>;
+		pinctrl-names = "active";
+		#pwm-cells = <3>;
+		status = "disabled";
+	};
+
+	pinctrl: pinctrl {
+		compatible = "rockchip,rk3568-pinctrl";
+		rockchip,grf = <&grf>;
+		rockchip,pmu = <&pmugrf>;
+		#address-cells = <2>;
+		#size-cells = <2>;
+		ranges;
+
+		gpio0: gpio@fdd60000 {
+			compatible = "rockchip,gpio-bank";
+			reg = <0x0 0xfdd60000 0x0 0x100>;
+			interrupts = <GIC_SPI 33 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&pmucru PCLK_GPIO0>, <&pmucru DBCLK_GPIO0>;
+			gpio-controller;
+			#gpio-cells = <2>;
+			interrupt-controller;
+			#interrupt-cells = <2>;
+		};
+
+		gpio1: gpio@fe740000 {
+			compatible = "rockchip,gpio-bank";
+			reg = <0x0 0xfe740000 0x0 0x100>;
+			interrupts = <GIC_SPI 34 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&cru PCLK_GPIO1>, <&cru DBCLK_GPIO1>;
+			gpio-controller;
+			#gpio-cells = <2>;
+			interrupt-controller;
+			#interrupt-cells = <2>;
+		};
+
+		gpio2: gpio@fe750000 {
+			compatible = "rockchip,gpio-bank";
+			reg = <0x0 0xfe750000 0x0 0x100>;
+			interrupts = <GIC_SPI 35 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&cru PCLK_GPIO2>, <&cru DBCLK_GPIO2>;
+			gpio-controller;
+			#gpio-cells = <2>;
+			interrupt-controller;
+			#interrupt-cells = <2>;
+		};
+
+		gpio3: gpio@fe760000 {
+			compatible = "rockchip,gpio-bank";
+			reg = <0x0 0xfe760000 0x0 0x100>;
+			interrupts = <GIC_SPI 36 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&cru PCLK_GPIO3>, <&cru DBCLK_GPIO3>;
+			gpio-controller;
+			#gpio-cells = <2>;
+			interrupt-controller;
+			#interrupt-cells = <2>;
+		};
+
+		gpio4: gpio@fe770000 {
+			compatible = "rockchip,gpio-bank";
+			reg = <0x0 0xfe770000 0x0 0x100>;
+			interrupts = <GIC_SPI 37 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&cru PCLK_GPIO4>, <&cru DBCLK_GPIO4>;
+			gpio-controller;
+			#gpio-cells = <2>;
+			interrupt-controller;
+			#interrupt-cells = <2>;
+		};
+	};
+};
+
+#include "rk3568-pinctrl.dtsi"
diff --git a/arch/arm64/boot/dts/ti/Makefile b/arch/arm64/boot/dts/ti/Makefile
index d56c742f5a10..71f6097d4621 100644
--- a/arch/arm64/boot/dts/ti/Makefile
+++ b/arch/arm64/boot/dts/ti/Makefile
@@ -8,12 +8,14 @@
 
 dtb-$(CONFIG_ARCH_K3) += k3-am654-base-board.dtb
 dtb-$(CONFIG_ARCH_K3) += k3-am6528-iot2050-basic.dtb
+dtb-$(CONFIG_ARCH_K3) += k3-am6528-iot2050-basic-pg2.dtb
 dtb-$(CONFIG_ARCH_K3) += k3-am6548-iot2050-advanced.dtb
+dtb-$(CONFIG_ARCH_K3) += k3-am6548-iot2050-advanced-pg2.dtb
 
 dtb-$(CONFIG_ARCH_K3) += k3-j721e-common-proc-board.dtb
+dtb-$(CONFIG_ARCH_K3) += k3-j721e-sk.dtb
 
 dtb-$(CONFIG_ARCH_K3) += k3-j7200-common-proc-board.dtb
 
 dtb-$(CONFIG_ARCH_K3) += k3-am642-evm.dtb
-
 dtb-$(CONFIG_ARCH_K3) += k3-am642-sk.dtb
diff --git a/arch/arm64/boot/dts/ti/k3-am64-main.dtsi b/arch/arm64/boot/dts/ti/k3-am64-main.dtsi
index 42d1d219a3fd..5ad638b95ffc 100644
--- a/arch/arm64/boot/dts/ti/k3-am64-main.dtsi
+++ b/arch/arm64/boot/dts/ti/k3-am64-main.dtsi
@@ -973,4 +973,284 @@
 		clocks = <&k3_clks 53 0>;
 		clock-names = "fck";
 	};
+
+	icssg0: icssg@30000000 {
+		compatible = "ti,am642-icssg";
+		reg = <0x00 0x30000000 0x00 0x80000>;
+		power-domains = <&k3_pds 81 TI_SCI_PD_EXCLUSIVE>;
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges = <0x0 0x00 0x30000000 0x80000>;
+
+		icssg0_mem: memories@0 {
+			reg = <0x0 0x2000>,
+			      <0x2000 0x2000>,
+			      <0x10000 0x10000>;
+			reg-names = "dram0", "dram1", "shrdram2";
+		};
+
+		icssg0_cfg: cfg@26000 {
+			compatible = "ti,pruss-cfg", "syscon";
+			reg = <0x26000 0x200>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges = <0x0 0x26000 0x2000>;
+
+			clocks {
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				icssg0_coreclk_mux: coreclk-mux@3c {
+					reg = <0x3c>;
+					#clock-cells = <0>;
+					clocks = <&k3_clks 81 0>,  /* icssg0_core_clk */
+						 <&k3_clks 81 20>; /* icssg0_iclk */
+					assigned-clocks = <&icssg0_coreclk_mux>;
+					assigned-clock-parents = <&k3_clks 81 20>;
+				};
+
+				icssg0_iepclk_mux: iepclk-mux@30 {
+					reg = <0x30>;
+					#clock-cells = <0>;
+					clocks = <&k3_clks 81 3>,	/* icssg0_iep_clk */
+						 <&icssg0_coreclk_mux>;	/* icssg0_coreclk_mux */
+					assigned-clocks = <&icssg0_iepclk_mux>;
+					assigned-clock-parents = <&icssg0_coreclk_mux>;
+				};
+			};
+		};
+
+		icssg0_mii_rt: mii-rt@32000 {
+			compatible = "ti,pruss-mii", "syscon";
+			reg = <0x32000 0x100>;
+		};
+
+		icssg0_mii_g_rt: mii-g-rt@33000 {
+			compatible = "ti,pruss-mii-g", "syscon";
+			reg = <0x33000 0x1000>;
+		};
+
+		icssg0_intc: interrupt-controller@20000 {
+			compatible = "ti,icssg-intc";
+			reg = <0x20000 0x2000>;
+			interrupt-controller;
+			#interrupt-cells = <3>;
+			interrupts = <GIC_SPI 88 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 89 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 90 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 91 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 92 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 93 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 94 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 95 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "host_intr0", "host_intr1",
+					  "host_intr2", "host_intr3",
+					  "host_intr4", "host_intr5",
+					  "host_intr6", "host_intr7";
+		};
+
+		pru0_0: pru@34000 {
+			compatible = "ti,am642-pru";
+			reg = <0x34000 0x3000>,
+			      <0x22000 0x100>,
+			      <0x22400 0x100>;
+			reg-names = "iram", "control", "debug";
+			firmware-name = "am64x-pru0_0-fw";
+		};
+
+		rtu0_0: rtu@4000 {
+			compatible = "ti,am642-rtu";
+			reg = <0x4000 0x2000>,
+			      <0x23000 0x100>,
+			      <0x23400 0x100>;
+			reg-names = "iram", "control", "debug";
+			firmware-name = "am64x-rtu0_0-fw";
+		};
+
+		tx_pru0_0: txpru@a000 {
+			compatible = "ti,am642-tx-pru";
+			reg = <0xa000 0x1800>,
+			      <0x25000 0x100>,
+			      <0x25400 0x100>;
+			reg-names = "iram", "control", "debug";
+			firmware-name = "am64x-txpru0_0-fw";
+		};
+
+		pru0_1: pru@38000 {
+			compatible = "ti,am642-pru";
+			reg = <0x38000 0x3000>,
+			      <0x24000 0x100>,
+			      <0x24400 0x100>;
+			reg-names = "iram", "control", "debug";
+			firmware-name = "am64x-pru0_1-fw";
+		};
+
+		rtu0_1: rtu@6000 {
+			compatible = "ti,am642-rtu";
+			reg = <0x6000 0x2000>,
+			      <0x23800 0x100>,
+			      <0x23c00 0x100>;
+			reg-names = "iram", "control", "debug";
+			firmware-name = "am64x-rtu0_1-fw";
+		};
+
+		tx_pru0_1: txpru@c000 {
+			compatible = "ti,am642-tx-pru";
+			reg = <0xc000 0x1800>,
+			      <0x25800 0x100>,
+			      <0x25c00 0x100>;
+			reg-names = "iram", "control", "debug";
+			firmware-name = "am64x-txpru0_1-fw";
+		};
+
+		icssg0_mdio: mdio@32400 {
+			compatible = "ti,davinci_mdio";
+			reg = <0x32400 0x100>;
+			clocks = <&k3_clks 62 3>;
+			clock-names = "fck";
+			#address-cells = <1>;
+			#size-cells = <0>;
+			bus_freq = <1000000>;
+		};
+	};
+
+	icssg1: icssg@30080000 {
+		compatible = "ti,am642-icssg";
+		reg = <0x00 0x30080000 0x00 0x80000>;
+		power-domains = <&k3_pds 82 TI_SCI_PD_EXCLUSIVE>;
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges = <0x0 0x00 0x30080000 0x80000>;
+
+		icssg1_mem: memories@0 {
+			reg = <0x0 0x2000>,
+			      <0x2000 0x2000>,
+			      <0x10000 0x10000>;
+			reg-names = "dram0", "dram1", "shrdram2";
+		};
+
+		icssg1_cfg: cfg@26000 {
+			compatible = "ti,pruss-cfg", "syscon";
+			reg = <0x26000 0x200>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges = <0x0 0x26000 0x2000>;
+
+			clocks {
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				icssg1_coreclk_mux: coreclk-mux@3c {
+					reg = <0x3c>;
+					#clock-cells = <0>;
+					clocks = <&k3_clks 82 0>,   /* icssg1_core_clk */
+						 <&k3_clks 82 20>;  /* icssg1_iclk */
+					assigned-clocks = <&icssg1_coreclk_mux>;
+					assigned-clock-parents = <&k3_clks 82 20>;
+				};
+
+				icssg1_iepclk_mux: iepclk-mux@30 {
+					reg = <0x30>;
+					#clock-cells = <0>;
+					clocks = <&k3_clks 82 3>,	/* icssg1_iep_clk */
+						 <&icssg1_coreclk_mux>;	/* icssg1_coreclk_mux */
+					assigned-clocks = <&icssg1_iepclk_mux>;
+					assigned-clock-parents = <&icssg1_coreclk_mux>;
+				};
+			};
+		};
+
+		icssg1_mii_rt: mii-rt@32000 {
+			compatible = "ti,pruss-mii", "syscon";
+			reg = <0x32000 0x100>;
+		};
+
+		icssg1_mii_g_rt: mii-g-rt@33000 {
+			compatible = "ti,pruss-mii-g", "syscon";
+			reg = <0x33000 0x1000>;
+		};
+
+		icssg1_intc: interrupt-controller@20000 {
+			compatible = "ti,icssg-intc";
+			reg = <0x20000 0x2000>;
+			interrupt-controller;
+			#interrupt-cells = <3>;
+			interrupts = <GIC_SPI 216 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 217 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 218 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 219 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 220 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 221 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 222 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 223 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "host_intr0", "host_intr1",
+					  "host_intr2", "host_intr3",
+					  "host_intr4", "host_intr5",
+					  "host_intr6", "host_intr7";
+		};
+
+		pru1_0: pru@34000 {
+			compatible = "ti,am642-pru";
+			reg = <0x34000 0x4000>,
+			      <0x22000 0x100>,
+			      <0x22400 0x100>;
+			reg-names = "iram", "control", "debug";
+			firmware-name = "am64x-pru1_0-fw";
+		};
+
+		rtu1_0: rtu@4000 {
+			compatible = "ti,am642-rtu";
+			reg = <0x4000 0x2000>,
+			      <0x23000 0x100>,
+			      <0x23400 0x100>;
+			reg-names = "iram", "control", "debug";
+			firmware-name = "am64x-rtu1_0-fw";
+		};
+
+		tx_pru1_0: txpru@a000 {
+			compatible = "ti,am642-tx-pru";
+			reg = <0xa000 0x1800>,
+			      <0x25000 0x100>,
+			      <0x25400 0x100>;
+			reg-names = "iram", "control", "debug";
+			firmware-name = "am64x-txpru1_0-fw";
+		};
+
+		pru1_1: pru@38000 {
+			compatible = "ti,am642-pru";
+			reg = <0x38000 0x4000>,
+			      <0x24000 0x100>,
+			      <0x24400 0x100>;
+			reg-names = "iram", "control", "debug";
+			firmware-name = "am64x-pru1_1-fw";
+		};
+
+		rtu1_1: rtu@6000 {
+			compatible = "ti,am642-rtu";
+			reg = <0x6000 0x2000>,
+			      <0x23800 0x100>,
+			      <0x23c00 0x100>;
+			reg-names = "iram", "control", "debug";
+			firmware-name = "am64x-rtu1_1-fw";
+		};
+
+		tx_pru1_1: txpru@c000 {
+			compatible = "ti,am642-tx-pru";
+			reg = <0xc000 0x1800>,
+			      <0x25800 0x100>,
+			      <0x25c00 0x100>;
+			reg-names = "iram", "control", "debug";
+			firmware-name = "am64x-txpru1_1-fw";
+		};
+
+		icssg1_mdio: mdio@32400 {
+			compatible = "ti,davinci_mdio";
+			reg = <0x32400 0x100>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			clocks = <&k3_clks 82 0>;
+			clock-names = "fck";
+			bus_freq = <1000000>;
+		};
+	};
 };
diff --git a/arch/arm64/boot/dts/ti/k3-am64-mcu.dtsi b/arch/arm64/boot/dts/ti/k3-am64-mcu.dtsi
index 59cc58f7d0c8..2bb5c9ff172c 100644
--- a/arch/arm64/boot/dts/ti/k3-am64-mcu.dtsi
+++ b/arch/arm64/boot/dts/ti/k3-am64-mcu.dtsi
@@ -97,4 +97,12 @@
 		clocks = <&k3_clks 79 0>;
 		clock-names = "gpio";
 	};
+
+	mcu_pmx0: pinctrl@4084000 {
+		compatible = "pinctrl-single";
+		reg = <0x00 0x4084000 0x00 0x84>;
+		#pinctrl-cells = <1>;
+		pinctrl-single,register-width = <32>;
+		pinctrl-single,function-mask = <0xffffffff>;
+	};
 };
diff --git a/arch/arm64/boot/dts/ti/k3-am64.dtsi b/arch/arm64/boot/dts/ti/k3-am64.dtsi
index de6805b0c72c..120974726be8 100644
--- a/arch/arm64/boot/dts/ti/k3-am64.dtsi
+++ b/arch/arm64/boot/dts/ti/k3-am64.dtsi
@@ -30,6 +30,8 @@
 		serial8 = &main_uart6;
 		ethernet0 = &cpsw_port1;
 		ethernet1 = &cpsw_port2;
+		mmc0 = &sdhci0;
+		mmc1 = &sdhci1;
 	};
 
 	chosen { };
diff --git a/arch/arm64/boot/dts/ti/k3-am642-evm.dts b/arch/arm64/boot/dts/ti/k3-am642-evm.dts
index 24ce4942618d..6726c4c7c28c 100644
--- a/arch/arm64/boot/dts/ti/k3-am642-evm.dts
+++ b/arch/arm64/boot/dts/ti/k3-am642-evm.dts
@@ -630,3 +630,11 @@
 &epwm8 {
 	status = "disabled";
 };
+
+&icssg0_mdio {
+	status = "disabled";
+};
+
+&icssg1_mdio {
+	status = "disabled";
+};
diff --git a/arch/arm64/boot/dts/ti/k3-am642-sk.dts b/arch/arm64/boot/dts/ti/k3-am642-sk.dts
index 6b45cdeeeefa..6b04745147be 100644
--- a/arch/arm64/boot/dts/ti/k3-am642-sk.dts
+++ b/arch/arm64/boot/dts/ti/k3-am642-sk.dts
@@ -517,3 +517,11 @@
 &epwm8 {
 	status = "disabled";
 };
+
+&icssg0_mdio {
+	status = "disabled";
+};
+
+&icssg1_mdio {
+	status = "disabled";
+};
diff --git a/arch/arm64/boot/dts/ti/k3-am65-iot2050-common-pg1.dtsi b/arch/arm64/boot/dts/ti/k3-am65-iot2050-common-pg1.dtsi
new file mode 100644
index 000000000000..51f902fa35a7
--- /dev/null
+++ b/arch/arm64/boot/dts/ti/k3-am65-iot2050-common-pg1.dtsi
@@ -0,0 +1,46 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright (c) Siemens AG, 2021
+ *
+ * Authors:
+ *   Jan Kiszka <jan.kiszka@siemens.com>
+ *
+ * Common bits of the IOT2050 Basic and Advanced variants, PG1
+ */
+
+&dss {
+	assigned-clocks = <&k3_clks 67 2>;
+	assigned-clock-parents = <&k3_clks 67 5>;
+};
+
+&serdes0 {
+	status = "disabled";
+};
+
+&sdhci1 {
+	no-1-8-v;
+};
+
+&tx_pru0_0 {
+	status = "disabled";
+};
+
+&tx_pru0_1 {
+	status = "disabled";
+};
+
+&tx_pru1_0 {
+	status = "disabled";
+};
+
+&tx_pru1_1 {
+	status = "disabled";
+};
+
+&tx_pru2_0 {
+	status = "disabled";
+};
+
+&tx_pru2_1 {
+	status = "disabled";
+};
diff --git a/arch/arm64/boot/dts/ti/k3-am65-iot2050-common-pg2.dtsi b/arch/arm64/boot/dts/ti/k3-am65-iot2050-common-pg2.dtsi
new file mode 100644
index 000000000000..e73458ca6900
--- /dev/null
+++ b/arch/arm64/boot/dts/ti/k3-am65-iot2050-common-pg2.dtsi
@@ -0,0 +1,51 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright (c) Siemens AG, 2021
+ *
+ * Authors:
+ *   Chao Zeng <chao.zeng@siemens.com>
+ *   Jan Kiszka <jan.kiszka@siemens.com>
+ *
+ * Common bits of the IOT2050 Basic and Advanced variants, PG2
+ */
+
+&main_pmx0 {
+	cp2102n_reset_pin_default: cp2102n-reset-pin-default {
+		pinctrl-single,pins = <
+			/* (AF12) GPIO1_24, used as cp2102 reset */
+			AM65X_IOPAD(0x01e0, PIN_OUTPUT, 7)
+		>;
+	};
+};
+
+&main_gpio1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&cp2102n_reset_pin_default>;
+	gpio-line-names =
+		"", "", "", "", "", "", "", "", "", "",
+		"", "", "", "", "", "", "", "", "", "",
+		"", "", "", "", "CP2102N-RESET";
+};
+
+&dss {
+	/* Workaround needed to get DP clock of 154Mhz */
+	assigned-clocks = <&k3_clks 67 0>;
+};
+
+&serdes0 {
+	assigned-clocks = <&k3_clks 153 4>, <&serdes0 AM654_SERDES_CMU_REFCLK>;
+	assigned-clock-parents = <&k3_clks 153 7>, <&k3_clks 153 4>;
+};
+
+&dwc3_0 {
+	assigned-clock-parents = <&k3_clks 151 4>,  /* set REF_CLK to 20MHz i.e. PER0_PLL/48 */
+				 <&k3_clks 151 8>;  /* set PIPE3_TXB_CLK to WIZ8B2M4VSB */
+	phys = <&serdes0 PHY_TYPE_USB3 0>;
+	phy-names = "usb3-phy";
+};
+
+&usb0 {
+	maximum-speed = "super-speed";
+	snps,dis-u1-entry-quirk;
+	snps,dis-u2-entry-quirk;
+};
diff --git a/arch/arm64/boot/dts/ti/k3-am65-iot2050-common.dtsi b/arch/arm64/boot/dts/ti/k3-am65-iot2050-common.dtsi
index 1008e9162ba2..65da226847f4 100644
--- a/arch/arm64/boot/dts/ti/k3-am65-iot2050-common.dtsi
+++ b/arch/arm64/boot/dts/ti/k3-am65-iot2050-common.dtsi
@@ -4,19 +4,19 @@
  *
  * Authors:
  *   Le Jin <le.jin@siemens.com>
- *   Jan Kiszka <jan.kiszk@siemens.com>
+ *   Jan Kiszka <jan.kiszka@siemens.com>
  *
- * Common bits of the IOT2050 Basic and Advanced variants
+ * Common bits of the IOT2050 Basic and Advanced variants, PG1 and PG2
  */
 
-/dts-v1/;
-
 #include "k3-am654.dtsi"
 #include <dt-bindings/phy/phy.h>
 
 / {
 	aliases {
 		spi0 = &mcu_spi0;
+		mmc0 = &sdhci1;
+		mmc1 = &sdhci0;
 	};
 
 	chosen {
@@ -555,7 +555,6 @@
 	pinctrl-0 = <&main_mmc1_pins_default>;
 	ti,driver-strength-ohm = <50>;
 	disable-wp;
-	no-1-8-v;
 };
 
 &usb0 {
@@ -629,10 +628,6 @@
 	};
 };
 
-&serdes0 {
-	status = "disabled";
-};
-
 &pcie0_rc {
 	status = "disabled";
 };
@@ -656,11 +651,21 @@
 };
 
 &mailbox0_cluster0 {
-	status = "disabled";
+	interrupts = <436>;
+
+	mbox_mcu_r5fss0_core0: mbox-mcu-r5fss0-core0 {
+		ti,mbox-tx = <1 0 0>;
+		ti,mbox-rx = <0 0 0>;
+	};
 };
 
 &mailbox0_cluster1 {
-	status = "disabled";
+	interrupts = <432>;
+
+	mbox_mcu_r5fss0_core1: mbox-mcu-r5fss0-core1 {
+		ti,mbox-tx = <1 0 0>;
+		ti,mbox-rx = <0 0 0>;
+	};
 };
 
 &mailbox0_cluster2 {
@@ -703,6 +708,18 @@
 	status = "disabled";
 };
 
+&mcu_r5fss0_core0 {
+	memory-region = <&mcu_r5fss0_core0_dma_memory_region>,
+			<&mcu_r5fss0_core0_memory_region>;
+	mboxes = <&mailbox0_cluster0 &mbox_mcu_r5fss0_core0>;
+};
+
+&mcu_r5fss0_core1 {
+	memory-region = <&mcu_r5fss0_core1_dma_memory_region>,
+			<&mcu_r5fss0_core1_memory_region>;
+	mboxes = <&mailbox0_cluster1 &mbox_mcu_r5fss0_core1>;
+};
+
 &icssg0_mdio {
 	status = "disabled";
 };
diff --git a/arch/arm64/boot/dts/ti/k3-am65-main.dtsi b/arch/arm64/boot/dts/ti/k3-am65-main.dtsi
index ba4e5d3e1ed7..ce8bb4a61011 100644
--- a/arch/arm64/boot/dts/ti/k3-am65-main.dtsi
+++ b/arch/arm64/boot/dts/ti/k3-am65-main.dtsi
@@ -692,8 +692,8 @@
 		power-domains = <&k3_pds 120 TI_SCI_PD_EXCLUSIVE>;
 		#address-cells = <3>;
 		#size-cells = <2>;
-		ranges = <0x81000000 0 0          0x0 0x10020000 0 0x00010000
-			  0x82000000 0 0x10030000 0x0 0x10030000 0 0x07FD0000>;
+		ranges = <0x81000000 0 0          0x0 0x10020000 0 0x00010000>,
+			 <0x82000000 0 0x10030000 0x0 0x10030000 0 0x07FD0000>;
 		ti,syscon-pcie-id = <&pcie_devid>;
 		ti,syscon-pcie-mode = <&pcie0_mode>;
 		bus-range = <0x0 0xff>;
@@ -725,8 +725,8 @@
 		power-domains = <&k3_pds 121 TI_SCI_PD_EXCLUSIVE>;
 		#address-cells = <3>;
 		#size-cells = <2>;
-		ranges = <0x81000000 0 0          0x0   0x18020000 0 0x00010000
-			  0x82000000 0 0x18030000 0x0   0x18030000 0 0x07FD0000>;
+		ranges = <0x81000000 0 0          0x0   0x18020000 0 0x00010000>,
+			 <0x82000000 0 0x18030000 0x0   0x18030000 0 0x07FD0000>;
 		ti,syscon-pcie-id = <&pcie_devid>;
 		ti,syscon-pcie-mode = <&pcie1_mode>;
 		bus-range = <0x0 0xff>;
diff --git a/arch/arm64/boot/dts/ti/k3-am65-wakeup.dtsi b/arch/arm64/boot/dts/ti/k3-am65-wakeup.dtsi
index 9d21cdf6fce8..9c69d0917f69 100644
--- a/arch/arm64/boot/dts/ti/k3-am65-wakeup.dtsi
+++ b/arch/arm64/boot/dts/ti/k3-am65-wakeup.dtsi
@@ -100,8 +100,4 @@
 		power-domains = <&k3_pds 80 TI_SCI_PD_EXCLUSIVE>;
 		#thermal-sensor-cells = <1>;
 	};
-
-	thermal_zones: thermal-zones {
-		#include "k3-am654-industrial-thermal.dtsi"
-	};
 };
diff --git a/arch/arm64/boot/dts/ti/k3-am65.dtsi b/arch/arm64/boot/dts/ti/k3-am65.dtsi
index a9fc1af03f27..a58a39fa42db 100644
--- a/arch/arm64/boot/dts/ti/k3-am65.dtsi
+++ b/arch/arm64/boot/dts/ti/k3-am65.dtsi
@@ -31,6 +31,8 @@
 		i2c4 = &main_i2c2;
 		i2c5 = &main_i2c3;
 		ethernet0 = &cpsw_port1;
+		mmc0 = &sdhci0;
+		mmc1 = &sdhci1;
 	};
 
 	chosen { };
diff --git a/arch/arm64/boot/dts/ti/k3-am6528-iot2050-basic-common.dtsi b/arch/arm64/boot/dts/ti/k3-am6528-iot2050-basic-common.dtsi
new file mode 100644
index 000000000000..4a9bf7d7c07d
--- /dev/null
+++ b/arch/arm64/boot/dts/ti/k3-am6528-iot2050-basic-common.dtsi
@@ -0,0 +1,60 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright (c) Siemens AG, 2018-2021
+ *
+ * Authors:
+ *   Le Jin <le.jin@siemens.com>
+ *   Jan Kiszka <jan.kiszka@siemens.com>
+ *
+ * Common bits of the IOT2050 Basic variant, PG1 and PG2
+ */
+
+#include "k3-am65-iot2050-common.dtsi"
+
+/ {
+	memory@80000000 {
+		device_type = "memory";
+		/* 1G RAM */
+		reg = <0x00000000 0x80000000 0x00000000 0x40000000>;
+	};
+
+	cpus {
+		cpu-map {
+			/delete-node/ cluster1;
+		};
+		/delete-node/ cpu@100;
+		/delete-node/ cpu@101;
+	};
+
+	/delete-node/ l2-cache1;
+};
+
+/* eMMC */
+&sdhci0 {
+	status = "disabled";
+};
+
+&main_pmx0 {
+	main_uart0_pins_default: main-uart0-pins-default {
+		pinctrl-single,pins = <
+			AM65X_IOPAD(0x01e4, PIN_INPUT,  0)  /* (AF11) UART0_RXD */
+			AM65X_IOPAD(0x01e8, PIN_OUTPUT, 0)  /* (AE11) UART0_TXD */
+			AM65X_IOPAD(0x01ec, PIN_INPUT,  0)  /* (AG11) UART0_CTSn */
+			AM65X_IOPAD(0x01f0, PIN_OUTPUT, 0)  /* (AD11) UART0_RTSn */
+			AM65X_IOPAD(0x0188, PIN_INPUT,  1)  /* (D25) UART0_DCDn */
+			AM65X_IOPAD(0x018c, PIN_INPUT,  1)  /* (B26) UART0_DSRn */
+			AM65X_IOPAD(0x0190, PIN_OUTPUT, 1)  /* (A24) UART0_DTRn */
+			AM65X_IOPAD(0x0194, PIN_INPUT,  1)  /* (E24) UART0_RIN */
+		>;
+	};
+};
+
+&main_uart0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&main_uart0_pins_default>;
+};
+
+&mcu_r5fss0 {
+	/* lock-step mode not supported on Basic boards */
+	ti,cluster-mode = <0>;
+};
diff --git a/arch/arm64/boot/dts/ti/k3-am6528-iot2050-basic-pg2.dts b/arch/arm64/boot/dts/ti/k3-am6528-iot2050-basic-pg2.dts
new file mode 100644
index 000000000000..c62549a4b436
--- /dev/null
+++ b/arch/arm64/boot/dts/ti/k3-am6528-iot2050-basic-pg2.dts
@@ -0,0 +1,24 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright (c) Siemens AG, 2018-2021
+ *
+ * Authors:
+ *   Le Jin <le.jin@siemens.com>
+ *   Jan Kiszka <jan.kiszka@siemens.com>
+ *
+ * AM6528-based (dual-core) IOT2050 Basic variant, Product Generation 2
+ * 1 GB RAM, no eMMC, main_uart0 on connector X30
+ *
+ * Product homepage:
+ * https://new.siemens.com/global/en/products/automation/pc-based/iot-gateways/simatic-iot2050.html
+ */
+
+/dts-v1/;
+
+#include "k3-am6528-iot2050-basic-common.dtsi"
+#include "k3-am65-iot2050-common-pg2.dtsi"
+
+/ {
+	compatible = "siemens,iot2050-basic-pg2", "ti,am654";
+	model = "SIMATIC IOT2050 Basic PG2";
+};
diff --git a/arch/arm64/boot/dts/ti/k3-am6528-iot2050-basic.dts b/arch/arm64/boot/dts/ti/k3-am6528-iot2050-basic.dts
index 94bb5dd39122..87928ff28214 100644
--- a/arch/arm64/boot/dts/ti/k3-am6528-iot2050-basic.dts
+++ b/arch/arm64/boot/dts/ti/k3-am6528-iot2050-basic.dts
@@ -4,63 +4,21 @@
  *
  * Authors:
  *   Le Jin <le.jin@siemens.com>
- *   Jan Kiszka <jan.kiszk@siemens.com>
+ *   Jan Kiszka <jan.kiszka@siemens.com>
  *
- * AM6528-based (dual-core) IOT2050 Basic variant
+ * AM6528-based (dual-core) IOT2050 Basic variant, Product Generation 1
  * 1 GB RAM, no eMMC, main_uart0 on connector X30
+ *
+ * Product homepage:
+ * https://new.siemens.com/global/en/products/automation/pc-based/iot-gateways/simatic-iot2050.html
  */
 
 /dts-v1/;
 
-#include "k3-am65-iot2050-common.dtsi"
+#include "k3-am6528-iot2050-basic-common.dtsi"
+#include "k3-am65-iot2050-common-pg1.dtsi"
 
 / {
 	compatible = "siemens,iot2050-basic", "ti,am654";
 	model = "SIMATIC IOT2050 Basic";
-
-	memory@80000000 {
-		device_type = "memory";
-		/* 1G RAM */
-		reg = <0x00000000 0x80000000 0x00000000 0x40000000>;
-	};
-
-	cpus {
-		cpu-map {
-			/delete-node/ cluster1;
-		};
-		/delete-node/ cpu@100;
-		/delete-node/ cpu@101;
-	};
-
-	/delete-node/ l2-cache1;
-};
-
-/* eMMC */
-&sdhci0 {
-	status = "disabled";
-};
-
-&main_pmx0 {
-	main_uart0_pins_default: main-uart0-pins-default {
-		pinctrl-single,pins = <
-			AM65X_IOPAD(0x01e4, PIN_INPUT,  0)  /* (AF11) UART0_RXD */
-			AM65X_IOPAD(0x01e8, PIN_OUTPUT, 0)  /* (AE11) UART0_TXD */
-			AM65X_IOPAD(0x01ec, PIN_INPUT,  0)  /* (AG11) UART0_CTSn */
-			AM65X_IOPAD(0x01f0, PIN_OUTPUT, 0)  /* (AD11) UART0_RTSn */
-			AM65X_IOPAD(0x0188, PIN_INPUT,  1)  /* (D25) UART0_DCDn */
-			AM65X_IOPAD(0x018c, PIN_INPUT,  1)  /* (B26) UART0_DSRn */
-			AM65X_IOPAD(0x0190, PIN_OUTPUT, 1)  /* (A24) UART0_DTRn */
-			AM65X_IOPAD(0x0194, PIN_INPUT,  1)  /* (E24) UART0_RIN */
-		>;
-	};
-};
-
-&main_uart0 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&main_uart0_pins_default>;
-};
-
-&mcu_r5fss0 {
-	/* lock-step mode not supported on this board */
-	ti,cluster-mode = <0>;
 };
diff --git a/arch/arm64/boot/dts/ti/k3-am654.dtsi b/arch/arm64/boot/dts/ti/k3-am654.dtsi
index f0a6541b8042..a89257900047 100644
--- a/arch/arm64/boot/dts/ti/k3-am654.dtsi
+++ b/arch/arm64/boot/dts/ti/k3-am654.dtsi
@@ -112,4 +112,8 @@
 		compatible = "cache";
 		cache-level = <3>;
 	};
+
+	thermal_zones: thermal-zones {
+		#include "k3-am654-industrial-thermal.dtsi"
+	};
 };
diff --git a/arch/arm64/boot/dts/ti/k3-am6548-iot2050-advanced-common.dtsi b/arch/arm64/boot/dts/ti/k3-am6548-iot2050-advanced-common.dtsi
new file mode 100644
index 000000000000..d25e8b26187f
--- /dev/null
+++ b/arch/arm64/boot/dts/ti/k3-am6548-iot2050-advanced-common.dtsi
@@ -0,0 +1,56 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright (c) Siemens AG, 2018-2021
+ *
+ * Authors:
+ *   Le Jin <le.jin@siemens.com>
+ *   Jan Kiszka <jan.kiszka@siemens.com>
+ *
+ * Common bits of the IOT2050 Advanced variant, PG1 and PG2
+ */
+
+/dts-v1/;
+
+#include "k3-am65-iot2050-common.dtsi"
+
+/ {
+	memory@80000000 {
+		device_type = "memory";
+		/* 2G RAM */
+		reg = <0x00000000 0x80000000 0x00000000 0x80000000>;
+	};
+};
+
+&main_pmx0 {
+	main_mmc0_pins_default: main-mmc0-pins-default {
+		pinctrl-single,pins = <
+			AM65X_IOPAD(0x01a8, PIN_INPUT_PULLDOWN, 0)  /* (B25) MMC0_CLK */
+			AM65X_IOPAD(0x01ac, PIN_INPUT_PULLUP,   0)  /* (B27) MMC0_CMD */
+			AM65X_IOPAD(0x01a4, PIN_INPUT_PULLUP,   0)  /* (A26) MMC0_DAT0 */
+			AM65X_IOPAD(0x01a0, PIN_INPUT_PULLUP,   0)  /* (E25) MMC0_DAT1 */
+			AM65X_IOPAD(0x019c, PIN_INPUT_PULLUP,   0)  /* (C26) MMC0_DAT2 */
+			AM65X_IOPAD(0x0198, PIN_INPUT_PULLUP,   0)  /* (A25) MMC0_DAT3 */
+			AM65X_IOPAD(0x0194, PIN_INPUT_PULLUP,   0)  /* (E24) MMC0_DAT4 */
+			AM65X_IOPAD(0x0190, PIN_INPUT_PULLUP,   0)  /* (A24) MMC0_DAT5 */
+			AM65X_IOPAD(0x018c, PIN_INPUT_PULLUP,   0)  /* (B26) MMC0_DAT6 */
+			AM65X_IOPAD(0x0188, PIN_INPUT_PULLUP,   0)  /* (D25) MMC0_DAT7 */
+			AM65X_IOPAD(0x01b8, PIN_OUTPUT_PULLUP,  7)  /* (B23) MMC0_SDWP */
+			AM65X_IOPAD(0x01b4, PIN_INPUT_PULLUP,   0)  /* (A23) MMC0_SDCD */
+			AM65X_IOPAD(0x01b0, PIN_INPUT,          0)  /* (C25) MMC0_DS */
+		>;
+	};
+};
+
+/* eMMC */
+&sdhci0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&main_mmc0_pins_default>;
+	bus-width = <8>;
+	non-removable;
+	ti,driver-strength-ohm = <50>;
+	disable-wp;
+};
+
+&main_uart0 {
+	status = "disabled";
+};
diff --git a/arch/arm64/boot/dts/ti/k3-am6548-iot2050-advanced-pg2.dts b/arch/arm64/boot/dts/ti/k3-am6548-iot2050-advanced-pg2.dts
new file mode 100644
index 000000000000..f00dc86d01b9
--- /dev/null
+++ b/arch/arm64/boot/dts/ti/k3-am6548-iot2050-advanced-pg2.dts
@@ -0,0 +1,29 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright (c) Siemens AG, 2018-2021
+ *
+ * Authors:
+ *   Le Jin <le.jin@siemens.com>
+ *   Jan Kiszka <jan.kiszka@siemens.com>
+ *
+ * AM6548-based (quad-core) IOT2050 Advanced variant, Product Generation 2
+ * 2 GB RAM, 16 GB eMMC, USB-serial converter on connector X30
+ *
+ * Product homepage:
+ * https://new.siemens.com/global/en/products/automation/pc-based/iot-gateways/simatic-iot2050.html
+ */
+
+/dts-v1/;
+
+#include "k3-am6548-iot2050-advanced-common.dtsi"
+#include "k3-am65-iot2050-common-pg2.dtsi"
+
+/ {
+	compatible = "siemens,iot2050-advanced-pg2", "ti,am654";
+	model = "SIMATIC IOT2050 Advanced PG2";
+};
+
+&mcu_r5fss0 {
+	/* lock-step mode not supported on this board */
+	ti,cluster-mode = <0>;
+};
diff --git a/arch/arm64/boot/dts/ti/k3-am6548-iot2050-advanced.dts b/arch/arm64/boot/dts/ti/k3-am6548-iot2050-advanced.dts
index ec9617c13cdb..077f165bdc68 100644
--- a/arch/arm64/boot/dts/ti/k3-am6548-iot2050-advanced.dts
+++ b/arch/arm64/boot/dts/ti/k3-am6548-iot2050-advanced.dts
@@ -4,57 +4,21 @@
  *
  * Authors:
  *   Le Jin <le.jin@siemens.com>
- *   Jan Kiszka <jan.kiszk@siemens.com>
+ *   Jan Kiszka <jan.kiszka@siemens.com>
  *
- * AM6548-based (quad-core) IOT2050 Advanced variant
+ * AM6548-based (quad-core) IOT2050 Advanced variant, Product Generation 1
  * 2 GB RAM, 16 GB eMMC, USB-serial converter on connector X30
+ *
+ * Product homepage:
+ * https://new.siemens.com/global/en/products/automation/pc-based/iot-gateways/simatic-iot2050.html
  */
 
 /dts-v1/;
 
-#include "k3-am65-iot2050-common.dtsi"
+#include "k3-am6548-iot2050-advanced-common.dtsi"
+#include "k3-am65-iot2050-common-pg1.dtsi"
 
 / {
 	compatible = "siemens,iot2050-advanced", "ti,am654";
 	model = "SIMATIC IOT2050 Advanced";
-
-	memory@80000000 {
-		device_type = "memory";
-		/* 2G RAM */
-		reg = <0x00000000 0x80000000 0x00000000 0x80000000>;
-	};
-};
-
-&main_pmx0 {
-	main_mmc0_pins_default: main-mmc0-pins-default {
-		pinctrl-single,pins = <
-			AM65X_IOPAD(0x01a8, PIN_INPUT_PULLDOWN, 0)  /* (B25) MMC0_CLK */
-			AM65X_IOPAD(0x01ac, PIN_INPUT_PULLUP,   0)  /* (B27) MMC0_CMD */
-			AM65X_IOPAD(0x01a4, PIN_INPUT_PULLUP,   0)  /* (A26) MMC0_DAT0 */
-			AM65X_IOPAD(0x01a0, PIN_INPUT_PULLUP,   0)  /* (E25) MMC0_DAT1 */
-			AM65X_IOPAD(0x019c, PIN_INPUT_PULLUP,   0)  /* (C26) MMC0_DAT2 */
-			AM65X_IOPAD(0x0198, PIN_INPUT_PULLUP,   0)  /* (A25) MMC0_DAT3 */
-			AM65X_IOPAD(0x0194, PIN_INPUT_PULLUP,   0)  /* (E24) MMC0_DAT4 */
-			AM65X_IOPAD(0x0190, PIN_INPUT_PULLUP,   0)  /* (A24) MMC0_DAT5 */
-			AM65X_IOPAD(0x018c, PIN_INPUT_PULLUP,   0)  /* (B26) MMC0_DAT6 */
-			AM65X_IOPAD(0x0188, PIN_INPUT_PULLUP,   0)  /* (D25) MMC0_DAT7 */
-			AM65X_IOPAD(0x01b8, PIN_OUTPUT_PULLUP,  7)  /* (B23) MMC0_SDWP */
-			AM65X_IOPAD(0x01b4, PIN_INPUT_PULLUP,   0)  /* (A23) MMC0_SDCD */
-			AM65X_IOPAD(0x01b0, PIN_INPUT,          0)  /* (C25) MMC0_DS */
-		>;
-	};
-};
-
-/* eMMC */
-&sdhci0 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&main_mmc0_pins_default>;
-	bus-width = <8>;
-	non-removable;
-	ti,driver-strength-ohm = <50>;
-	disable-wp;
-};
-
-&main_uart0 {
-	status = "disabled";
 };
diff --git a/arch/arm64/boot/dts/ti/k3-j7200-common-proc-board.dts b/arch/arm64/boot/dts/ti/k3-j7200-common-proc-board.dts
index d14f3c18b65f..121975dc8239 100644
--- a/arch/arm64/boot/dts/ti/k3-j7200-common-proc-board.dts
+++ b/arch/arm64/boot/dts/ti/k3-j7200-common-proc-board.dts
@@ -12,6 +12,9 @@
 #include <dt-bindings/phy/phy.h>
 
 / {
+	compatible = "ti,j7200-evm", "ti,j7200";
+	model = "Texas Instruments J7200 EVM";
+
 	chosen {
 		stdout-path = "serial2:115200n8";
 		bootargs = "console=ttyS2,115200n8 earlycon=ns16550a,mmio32,0x02800000";
diff --git a/arch/arm64/boot/dts/ti/k3-j7200-main.dtsi b/arch/arm64/boot/dts/ti/k3-j7200-main.dtsi
index e8a41d09b45f..d60ef4f7dd0b 100644
--- a/arch/arm64/boot/dts/ti/k3-j7200-main.dtsi
+++ b/arch/arm64/boot/dts/ti/k3-j7200-main.dtsi
@@ -606,10 +606,10 @@
 		clock-names = "fck";
 		#address-cells = <3>;
 		#size-cells = <2>;
-		bus-range = <0x0 0xf>;
+		bus-range = <0x0 0xff>;
 		cdns,no-bar-match-nbits = <64>;
-		vendor-id = /bits/ 16 <0x104c>;
-		device-id = /bits/ 16 <0xb00f>;
+		vendor-id = <0x104c>;
+		device-id = <0xb00f>;
 		msi-map = <0x0 &gic_its 0x0 0x10000>;
 		dma-coherent;
 		ranges = <0x01000000 0x0 0x18001000  0x00 0x18001000  0x0 0x0010000>,
@@ -633,6 +633,7 @@
 		clocks = <&k3_clks 240 6>;
 		clock-names = "fck";
 		max-functions = /bits/ 8 <6>;
+		max-virtual-functions = /bits/ 8 <4 4 4 4 0 0>;
 		dma-coherent;
 	};
 
diff --git a/arch/arm64/boot/dts/ti/k3-j7200.dtsi b/arch/arm64/boot/dts/ti/k3-j7200.dtsi
index b7005b803149..47567cb260c2 100644
--- a/arch/arm64/boot/dts/ti/k3-j7200.dtsi
+++ b/arch/arm64/boot/dts/ti/k3-j7200.dtsi
@@ -30,6 +30,8 @@
 		serial9 = &main_uart7;
 		serial10 = &main_uart8;
 		serial11 = &main_uart9;
+		mmc0 = &main_sdhci0;
+		mmc1 = &main_sdhci1;
 	};
 
 	chosen { };
diff --git a/arch/arm64/boot/dts/ti/k3-j721e-common-proc-board.dts b/arch/arm64/boot/dts/ti/k3-j721e-common-proc-board.dts
index 8bd02d9e28ad..dc2bc67f9f48 100644
--- a/arch/arm64/boot/dts/ti/k3-j721e-common-proc-board.dts
+++ b/arch/arm64/boot/dts/ti/k3-j721e-common-proc-board.dts
@@ -12,6 +12,9 @@
 #include <dt-bindings/phy/phy-cadence.h>
 
 / {
+	compatible = "ti,j721e-evm", "ti,j721e";
+	model = "Texas Instruments J721e EVM";
+
 	chosen {
 		stdout-path = "serial2:115200n8";
 		bootargs = "console=ttyS2,115200n8 earlycon=ns16550a,mmio32,0x02800000";
diff --git a/arch/arm64/boot/dts/ti/k3-j721e-main.dtsi b/arch/arm64/boot/dts/ti/k3-j721e-main.dtsi
index cf3482376c1e..08c8d1b47dcd 100644
--- a/arch/arm64/boot/dts/ti/k3-j721e-main.dtsi
+++ b/arch/arm64/boot/dts/ti/k3-j721e-main.dtsi
@@ -610,7 +610,7 @@
 		clock-names = "fck";
 		#address-cells = <3>;
 		#size-cells = <2>;
-		bus-range = <0x0 0xf>;
+		bus-range = <0x0 0xff>;
 		vendor-id = <0x104c>;
 		device-id = <0xb00d>;
 		msi-map = <0x0 &gic_its 0x0 0x10000>;
@@ -636,7 +636,7 @@
 		clocks = <&k3_clks 239 1>;
 		clock-names = "fck";
 		max-functions = /bits/ 8 <6>;
-		max-virtual-functions = /bits/ 16 <4 4 4 4 0 0>;
+		max-virtual-functions = /bits/ 8 <4 4 4 4 0 0>;
 		dma-coherent;
 	};
 
@@ -658,7 +658,7 @@
 		clock-names = "fck";
 		#address-cells = <3>;
 		#size-cells = <2>;
-		bus-range = <0x0 0xf>;
+		bus-range = <0x0 0xff>;
 		vendor-id = <0x104c>;
 		device-id = <0xb00d>;
 		msi-map = <0x0 &gic_its 0x10000 0x10000>;
@@ -684,7 +684,7 @@
 		clocks = <&k3_clks 240 1>;
 		clock-names = "fck";
 		max-functions = /bits/ 8 <6>;
-		max-virtual-functions = /bits/ 16 <4 4 4 4 0 0>;
+		max-virtual-functions = /bits/ 8 <4 4 4 4 0 0>;
 		dma-coherent;
 	};
 
@@ -706,7 +706,7 @@
 		clock-names = "fck";
 		#address-cells = <3>;
 		#size-cells = <2>;
-		bus-range = <0x0 0xf>;
+		bus-range = <0x0 0xff>;
 		vendor-id = <0x104c>;
 		device-id = <0xb00d>;
 		msi-map = <0x0 &gic_its 0x20000 0x10000>;
@@ -732,7 +732,7 @@
 		clocks = <&k3_clks 241 1>;
 		clock-names = "fck";
 		max-functions = /bits/ 8 <6>;
-		max-virtual-functions = /bits/ 16 <4 4 4 4 0 0>;
+		max-virtual-functions = /bits/ 8 <4 4 4 4 0 0>;
 		dma-coherent;
 	};
 
@@ -754,7 +754,7 @@
 		clock-names = "fck";
 		#address-cells = <3>;
 		#size-cells = <2>;
-		bus-range = <0x0 0xf>;
+		bus-range = <0x0 0xff>;
 		vendor-id = <0x104c>;
 		device-id = <0xb00d>;
 		msi-map = <0x0 &gic_its 0x30000 0x10000>;
@@ -780,7 +780,7 @@
 		clocks = <&k3_clks 242 1>;
 		clock-names = "fck";
 		max-functions = /bits/ 8 <6>;
-		max-virtual-functions = /bits/ 16 <4 4 4 4 0 0>;
+		max-virtual-functions = /bits/ 8 <4 4 4 4 0 0>;
 		dma-coherent;
 		#address-cells = <2>;
 		#size-cells = <2>;
diff --git a/arch/arm64/boot/dts/ti/k3-j721e-sk.dts b/arch/arm64/boot/dts/ti/k3-j721e-sk.dts
new file mode 100644
index 000000000000..b726310d867c
--- /dev/null
+++ b/arch/arm64/boot/dts/ti/k3-j721e-sk.dts
@@ -0,0 +1,1002 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright (C) 2021 Texas Instruments Incorporated - https://www.ti.com/
+ *
+ * J721E SK URL: https://www.ti.com/tool/SK-TDA4VM
+ */
+
+/dts-v1/;
+
+#include "k3-j721e.dtsi"
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/net/ti-dp83867.h>
+
+/ {
+	compatible = "ti,j721e-sk", "ti,j721e";
+	model = "Texas Instruments J721E SK";
+
+	chosen {
+		stdout-path = "serial2:115200n8";
+		bootargs = "console=ttyS2,115200n8 earlycon=ns16550a,mmio32,0x02800000";
+	};
+
+	memory@80000000 {
+		device_type = "memory";
+		/* 4G RAM */
+		reg = <0x00000000 0x80000000 0x00000000 0x80000000>,
+		      <0x00000008 0x80000000 0x00000000 0x80000000>;
+	};
+
+	reserved_memory: reserved-memory {
+		#address-cells = <2>;
+		#size-cells = <2>;
+		ranges;
+
+		secure_ddr: optee@9e800000 {
+			reg = <0x00 0x9e800000 0x00 0x01800000>;
+			alignment = <0x1000>;
+			no-map;
+		};
+
+		mcu_r5fss0_core0_dma_memory_region: r5f-dma-memory@a0000000 {
+			compatible = "shared-dma-pool";
+			reg = <0x00 0xa0000000 0x00 0x100000>;
+			no-map;
+		};
+
+		mcu_r5fss0_core0_memory_region: r5f-memory@a0100000 {
+			compatible = "shared-dma-pool";
+			reg = <0x00 0xa0100000 0x00 0xf00000>;
+			no-map;
+		};
+
+		mcu_r5fss0_core1_dma_memory_region: r5f-dma-memory@a1000000 {
+			compatible = "shared-dma-pool";
+			reg = <0x00 0xa1000000 0x00 0x100000>;
+			no-map;
+		};
+
+		mcu_r5fss0_core1_memory_region: r5f-memory@a1100000 {
+			compatible = "shared-dma-pool";
+			reg = <0x00 0xa1100000 0x00 0xf00000>;
+			no-map;
+		};
+
+		main_r5fss0_core0_dma_memory_region: r5f-dma-memory@a2000000 {
+			compatible = "shared-dma-pool";
+			reg = <0x00 0xa2000000 0x00 0x100000>;
+			no-map;
+		};
+
+		main_r5fss0_core0_memory_region: r5f-memory@a2100000 {
+			compatible = "shared-dma-pool";
+			reg = <0x00 0xa2100000 0x00 0xf00000>;
+			no-map;
+		};
+
+		main_r5fss0_core1_dma_memory_region: r5f-dma-memory@a3000000 {
+			compatible = "shared-dma-pool";
+			reg = <0x00 0xa3000000 0x00 0x100000>;
+			no-map;
+		};
+
+		main_r5fss0_core1_memory_region: r5f-memory@a3100000 {
+			compatible = "shared-dma-pool";
+			reg = <0x00 0xa3100000 0x00 0xf00000>;
+			no-map;
+		};
+
+		main_r5fss1_core0_dma_memory_region: r5f-dma-memory@a4000000 {
+			compatible = "shared-dma-pool";
+			reg = <0x00 0xa4000000 0x00 0x100000>;
+			no-map;
+		};
+
+		main_r5fss1_core0_memory_region: r5f-memory@a4100000 {
+			compatible = "shared-dma-pool";
+			reg = <0x00 0xa4100000 0x00 0xf00000>;
+			no-map;
+		};
+
+		main_r5fss1_core1_dma_memory_region: r5f-dma-memory@a5000000 {
+			compatible = "shared-dma-pool";
+			reg = <0x00 0xa5000000 0x00 0x100000>;
+			no-map;
+		};
+
+		main_r5fss1_core1_memory_region: r5f-memory@a5100000 {
+			compatible = "shared-dma-pool";
+			reg = <0x00 0xa5100000 0x00 0xf00000>;
+			no-map;
+		};
+
+		c66_1_dma_memory_region: c66-dma-memory@a6000000 {
+			compatible = "shared-dma-pool";
+			reg = <0x00 0xa6000000 0x00 0x100000>;
+			no-map;
+		};
+
+		c66_0_memory_region: c66-memory@a6100000 {
+			compatible = "shared-dma-pool";
+			reg = <0x00 0xa6100000 0x00 0xf00000>;
+			no-map;
+		};
+
+		c66_0_dma_memory_region: c66-dma-memory@a7000000 {
+			compatible = "shared-dma-pool";
+			reg = <0x00 0xa7000000 0x00 0x100000>;
+			no-map;
+		};
+
+		c66_1_memory_region: c66-memory@a7100000 {
+			compatible = "shared-dma-pool";
+			reg = <0x00 0xa7100000 0x00 0xf00000>;
+			no-map;
+		};
+
+		c71_0_dma_memory_region: c71-dma-memory@a8000000 {
+			compatible = "shared-dma-pool";
+			reg = <0x00 0xa8000000 0x00 0x100000>;
+			no-map;
+		};
+
+		c71_0_memory_region: c71-memory@a8100000 {
+			compatible = "shared-dma-pool";
+			reg = <0x00 0xa8100000 0x00 0xf00000>;
+			no-map;
+		};
+
+		rtos_ipc_memory_region: ipc-memories@aa000000 {
+			reg = <0x00 0xaa000000 0x00 0x01c00000>;
+			alignment = <0x1000>;
+			no-map;
+		};
+	};
+
+	vusb_main: fixedregulator-vusb-main5v0 {
+		/* USB MAIN INPUT 5V DC */
+		compatible = "regulator-fixed";
+		regulator-name = "vusb-main5v0";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		regulator-always-on;
+		regulator-boot-on;
+	};
+
+	vsys_3v3: fixedregulator-vsys3v3 {
+		/* Output of LM5141 */
+		compatible = "regulator-fixed";
+		regulator-name = "vsys_3v3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		vin-supply = <&vusb_main>;
+		regulator-always-on;
+		regulator-boot-on;
+	};
+
+	vdd_mmc1: fixedregulator-sd {
+		compatible = "regulator-fixed";
+		pinctrl-names = "default";
+		pinctrl-0 = <&vdd_mmc1_en_pins_default>;
+		regulator-name = "vdd_mmc1";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-boot-on;
+		enable-active-high;
+		vin-supply = <&vsys_3v3>;
+		gpio = <&wkup_gpio0 8 GPIO_ACTIVE_HIGH>;
+	};
+
+	vdd_sd_dv_alt: gpio-regulator-tps659411 {
+		compatible = "regulator-gpio";
+		pinctrl-names = "default";
+		pinctrl-0 = <&vdd_sd_dv_alt_pins_default>;
+		regulator-name = "tps659411";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-boot-on;
+		vin-supply = <&vsys_3v3>;
+		gpios = <&wkup_gpio0 9 GPIO_ACTIVE_HIGH>;
+		states = <1800000 0x0>,
+			 <3300000 0x1>;
+	};
+
+	dp_pwr_3v3: fixedregulator-dp-prw {
+		compatible = "regulator-fixed";
+		regulator-name = "dp-pwr";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&dp_pwr_en_pins_default>;
+		gpio = <&main_gpio0 111 0>;	/* DP0_3V3 _EN */
+		enable-active-high;
+	};
+
+};
+
+&main_pmx0 {
+	main_mmc1_pins_default: main-mmc1-pins-default {
+		pinctrl-single,pins = <
+			J721E_IOPAD(0x254, PIN_INPUT, 0) /* (R29) MMC1_CMD */
+			J721E_IOPAD(0x250, PIN_INPUT, 0) /* (P25) MMC1_CLK */
+			J721E_IOPAD(0x2ac, PIN_INPUT, 0) /* (P25) MMC1_CLKLB */
+			J721E_IOPAD(0x24c, PIN_INPUT, 0) /* (R24) MMC1_DAT0 */
+			J721E_IOPAD(0x248, PIN_INPUT, 0) /* (P24) MMC1_DAT1 */
+			J721E_IOPAD(0x244, PIN_INPUT, 0) /* (R25) MMC1_DAT2 */
+			J721E_IOPAD(0x240, PIN_INPUT, 0) /* (R26) MMC1_DAT3 */
+			J721E_IOPAD(0x258, PIN_INPUT, 0) /* (P23) MMC1_SDCD */
+		>;
+	};
+
+	main_uart0_pins_default: main-uart0-pins-default {
+		pinctrl-single,pins = <
+			J721E_IOPAD(0x1f0, PIN_INPUT, 0) /* (AC2) UART0_CTSn */
+			J721E_IOPAD(0x1f4, PIN_OUTPUT, 0) /* (AB1) UART0_RTSn */
+			J721E_IOPAD(0x1e8, PIN_INPUT, 0) /* (AB2) UART0_RXD */
+			J721E_IOPAD(0x1ec, PIN_OUTPUT, 0) /* (AB3) UART0_TXD */
+		>;
+	};
+
+	main_i2c0_pins_default: main-i2c0-pins-default {
+		pinctrl-single,pins = <
+			J721E_IOPAD(0x220, PIN_INPUT_PULLUP, 0) /* (AC5) I2C0_SCL */
+			J721E_IOPAD(0x224, PIN_INPUT_PULLUP, 0) /* (AA5) I2C0_SDA */
+		>;
+	};
+
+	main_i2c1_pins_default: main-i2c1-pins-default {
+		pinctrl-single,pins = <
+			J721E_IOPAD(0x228, PIN_INPUT_PULLUP, 0) /* (Y6) I2C1_SCL */
+			J721E_IOPAD(0x22c, PIN_INPUT_PULLUP, 0) /* (AA6) I2C1_SDA */
+		>;
+	};
+
+	main_i2c3_pins_default: main-i2c3-pins-default {
+		pinctrl-single,pins = <
+			J721E_IOPAD(0x270, PIN_INPUT_PULLUP, 4) /* (T26) MMC2_CLK.I2C3_SCL */
+			J721E_IOPAD(0x274, PIN_INPUT_PULLUP, 4) /* (T25) MMC2_CMD.I2C3_SDA */
+		>;
+	};
+
+	main_usbss0_pins_default: main-usbss0-pins-default {
+		pinctrl-single,pins = <
+			J721E_IOPAD(0x290, PIN_OUTPUT, 0) /* (U6) USB0_DRVVBUS */
+			J721E_IOPAD(0x210, PIN_INPUT, 7) /* (W3) MCAN1_RX.GPIO1_3 */
+		>;
+	};
+
+	main_usbss1_pins_default: main-usbss1-pins-default {
+		pinctrl-single,pins = <
+			J721E_IOPAD(0x214, PIN_OUTPUT, 4) /* (V4) MCAN1_TX.USB1_DRVVBUS */
+		>;
+	};
+
+	dp0_pins_default: dp0-pins-default {
+		pinctrl-single,pins = <
+			J721E_IOPAD(0x1c4, PIN_INPUT, 5) /* SPI0_CS1.DP0_HPD */
+		>;
+	};
+
+	dp_pwr_en_pins_default: dp-pwr-en-pins-default {
+		pinctrl-single,pins = <
+			J721E_IOPAD(0x1c0, PIN_INPUT, 7) /* (AA2) SPI0_CS0.GPIO0_111 */
+		>;
+	};
+
+	dss_vout0_pins_default: dss-vout0-pins-default {
+		pinctrl-single,pins = <
+			J721E_IOPAD(0x58, PIN_OUTPUT, 10) /* (AE22) PRG1_PRU1_GPO0.VOUT0_DATA0 */
+			J721E_IOPAD(0x5c, PIN_OUTPUT, 10) /* (AG23) PRG1_PRU1_GPO1.VOUT0_DATA1 */
+			J721E_IOPAD(0x60, PIN_OUTPUT, 10) /* (AF23) PRG1_PRU1_GPO2.VOUT0_DATA2 */
+			J721E_IOPAD(0x64, PIN_OUTPUT, 10) /* (AD23) PRG1_PRU1_GPO3.VOUT0_DATA3 */
+			J721E_IOPAD(0x68, PIN_OUTPUT, 10) /* (AH24) PRG1_PRU1_GPO4.VOUT0_DATA4 */
+			J721E_IOPAD(0x6c, PIN_OUTPUT, 10) /* (AG21) PRG1_PRU1_GPO5.VOUT0_DATA5 */
+			J721E_IOPAD(0x70, PIN_OUTPUT, 10) /* (AE23) PRG1_PRU1_GPO6.VOUT0_DATA6 */
+			J721E_IOPAD(0x74, PIN_OUTPUT, 10) /* (AC21) PRG1_PRU1_GPO7.VOUT0_DATA7 */
+			J721E_IOPAD(0x78, PIN_OUTPUT, 10) /* (Y23) PRG1_PRU1_GPO8.VOUT0_DATA8 */
+			J721E_IOPAD(0x7c, PIN_OUTPUT, 10) /* (AF21) PRG1_PRU1_GPO9.VOUT0_DATA9 */
+			J721E_IOPAD(0x80, PIN_OUTPUT, 10) /* (AB23) PRG1_PRU1_GPO10.VOUT0_DATA10 */
+			J721E_IOPAD(0x84, PIN_OUTPUT, 10) /* (AJ25) PRG1_PRU1_GPO11.VOUT0_DATA11 */
+			J721E_IOPAD(0x88, PIN_OUTPUT, 10) /* (AH25) PRG1_PRU1_GPO12.VOUT0_DATA12 */
+			J721E_IOPAD(0x8c, PIN_OUTPUT, 10) /* (AG25) PRG1_PRU1_GPO13.VOUT0_DATA13 */
+			J721E_IOPAD(0x90, PIN_OUTPUT, 10) /* (AH26) PRG1_PRU1_GPO14.VOUT0_DATA14 */
+			J721E_IOPAD(0x94, PIN_OUTPUT, 10) /* (AJ27) PRG1_PRU1_GPO15.VOUT0_DATA15 */
+			J721E_IOPAD(0x30, PIN_OUTPUT, 10) /* (AF24) PRG1_PRU0_GPO11.VOUT0_DATA16 */
+			J721E_IOPAD(0x34, PIN_OUTPUT, 10) /* (AJ24) PRG1_PRU0_GPO12.VOUT0_DATA17 */
+			J721E_IOPAD(0x38, PIN_OUTPUT, 10) /* (AG24) PRG1_PRU0_GPO13.VOUT0_DATA18 */
+			J721E_IOPAD(0x3c, PIN_OUTPUT, 10) /* (AD24) PRG1_PRU0_GPO14.VOUT0_DATA19 */
+			J721E_IOPAD(0x40, PIN_OUTPUT, 10) /* (AC24) PRG1_PRU0_GPO15.VOUT0_DATA20 */
+			J721E_IOPAD(0x44, PIN_OUTPUT, 10) /* (AE24) PRG1_PRU0_GPO16.VOUT0_DATA21 */
+			J721E_IOPAD(0x24, PIN_OUTPUT, 10) /* (AJ20) PRG1_PRU0_GPO8.VOUT0_DATA22 */
+			J721E_IOPAD(0x28, PIN_OUTPUT, 10) /* (AG20) PRG1_PRU0_GPO9.VOUT0_DATA23 */
+			J721E_IOPAD(0x9c, PIN_OUTPUT, 10) /* (AC22) PRG1_PRU1_GPO17.VOUT0_DE */
+			J721E_IOPAD(0x98, PIN_OUTPUT, 10) /* (AJ26) PRG1_PRU1_GPO16.VOUT0_HSYNC */
+			J721E_IOPAD(0xa4, PIN_OUTPUT, 10) /* (AH22) PRG1_PRU1_GPO19.VOUT0_PCLK */
+			J721E_IOPAD(0xa0, PIN_OUTPUT, 10) /* (AJ22) PRG1_PRU1_GPO18.VOUT0_VSYNC */
+		>;
+	};
+
+	/* Reset for M.2 E Key slot on PCIe0  */
+	ekey_reset_pins_default: ekey-reset-pns-pins-default {
+		pinctrl-single,pins = <
+			J721E_IOPAD(0x124, PIN_INPUT, 7) /* (Y24) PRG0_PRU1_GPO9.GPIO0_72 */
+		>;
+	};
+};
+
+&wkup_pmx0 {
+	mcu_cpsw_pins_default: mcu-cpsw-pins-default {
+		pinctrl-single,pins = <
+			J721E_WKUP_IOPAD(0x84, PIN_INPUT, 0) /* (B24) MCU_RGMII1_RD0 */
+			J721E_WKUP_IOPAD(0x80, PIN_INPUT, 0) /* (A24) MCU_RGMII1_RD1 */
+			J721E_WKUP_IOPAD(0x7c, PIN_INPUT, 0) /* (D24) MCU_RGMII1_RD2 */
+			J721E_WKUP_IOPAD(0x78, PIN_INPUT, 0) /* (A25) MCU_RGMII1_RD3 */
+			J721E_WKUP_IOPAD(0x74, PIN_INPUT, 0) /* (C24) MCU_RGMII1_RXC */
+			J721E_WKUP_IOPAD(0x5c, PIN_INPUT, 0) /* (C25) MCU_RGMII1_RX_CTL */
+			J721E_WKUP_IOPAD(0x6c, PIN_OUTPUT, 0) /* (B25) MCU_RGMII1_TD0 */
+			J721E_WKUP_IOPAD(0x68, PIN_OUTPUT, 0) /* (A26) MCU_RGMII1_TD1 */
+			J721E_WKUP_IOPAD(0x64, PIN_OUTPUT, 0) /* (A27) MCU_RGMII1_TD2 */
+			J721E_WKUP_IOPAD(0x60, PIN_OUTPUT, 0) /* (A28) MCU_RGMII1_TD3 */
+			J721E_WKUP_IOPAD(0x70, PIN_OUTPUT, 0) /* (B26) MCU_RGMII1_TXC */
+			J721E_WKUP_IOPAD(0x58, PIN_OUTPUT, 0) /* (B27) MCU_RGMII1_TX_CTL */
+		>;
+	};
+
+	mcu_mdio_pins_default: mcu-mdio1-pins-default {
+		pinctrl-single,pins = <
+			J721E_WKUP_IOPAD(0x8c, PIN_OUTPUT, 0) /* (F23) MCU_MDIO0_MDC */
+			J721E_WKUP_IOPAD(0x88, PIN_INPUT, 0) /* (E23) MCU_MDIO0_MDIO */
+		>;
+	};
+
+	mcu_fss0_ospi0_pins_default: mcu-fss0-ospi0-pins-default {
+		pinctrl-single,pins = <
+			J721E_WKUP_IOPAD(0x0, PIN_OUTPUT, 0) /* (E20) MCU_OSPI0_CLK */
+			J721E_WKUP_IOPAD(0x2c, PIN_OUTPUT, 0) /* (F19) MCU_OSPI0_CSn0 */
+			J721E_WKUP_IOPAD(0xc, PIN_INPUT, 0) /* (D20) MCU_OSPI0_D0 */
+			J721E_WKUP_IOPAD(0x10, PIN_INPUT, 0) /* (G19) MCU_OSPI0_D1 */
+			J721E_WKUP_IOPAD(0x14, PIN_INPUT, 0) /* (G20) MCU_OSPI0_D2 */
+			J721E_WKUP_IOPAD(0x18, PIN_INPUT, 0) /* (F20) MCU_OSPI0_D3 */
+			J721E_WKUP_IOPAD(0x1c, PIN_INPUT, 0) /* (F21) MCU_OSPI0_D4 */
+			J721E_WKUP_IOPAD(0x20, PIN_INPUT, 0) /* (E21) MCU_OSPI0_D5 */
+			J721E_WKUP_IOPAD(0x24, PIN_INPUT, 0) /* (B22) MCU_OSPI0_D6 */
+			J721E_WKUP_IOPAD(0x28, PIN_INPUT, 0) /* (G21) MCU_OSPI0_D7 */
+			J721E_WKUP_IOPAD(0x8, PIN_INPUT, 0) /* (D21) MCU_OSPI0_DQS */
+		>;
+	};
+
+	vdd_mmc1_en_pins_default: vdd-mmc1-en-pins-default {
+		pinctrl-single,pins = <
+			J721E_WKUP_IOPAD(0xd0, PIN_OUTPUT, 7) /* (G27) WKUP_GPIO0_8 */
+		>;
+	};
+
+	vdd_sd_dv_alt_pins_default: vdd-sd-dv-alt-pins-default {
+		pinctrl-single,pins = <
+			J721E_WKUP_IOPAD(0xd4, PIN_OUTPUT, 7) /* (G26) WKUP_GPIO0_9 */
+		>;
+	};
+
+	wkup_i2c0_pins_default: wkup-i2c0-pins-default {
+		pinctrl-single,pins = <
+			J721E_WKUP_IOPAD(0xf8, PIN_INPUT_PULLUP, 0) /* (J25) WKUP_I2C0_SCL */
+			J721E_WKUP_IOPAD(0xfc, PIN_INPUT_PULLUP, 0) /* (H24) WKUP_I2C0_SDA */
+		>;
+	};
+
+	/* Reset for M.2 M Key slot on PCIe1  */
+	mkey_reset_pins_default: mkey-reset-pns-pins-default {
+		pinctrl-single,pins = <
+			J721E_WKUP_IOPAD(0xdc, PIN_INPUT, 7) /* (H27) WKUP_GPIO0_11 */
+		>;
+	};
+};
+
+&wkup_uart0 {
+	/* Wakeup UART is used by System firmware */
+	status = "reserved";
+};
+
+&main_uart0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&main_uart0_pins_default>;
+	/* Shared with ATF on this platform */
+	power-domains = <&k3_pds 146 TI_SCI_PD_SHARED>;
+};
+
+&main_uart2 {
+	/* Brought out on RPi header */
+	status = "disabled";
+};
+
+&main_uart3 {
+	/* UART not brought out */
+	status = "disabled";
+};
+
+&main_uart5 {
+	/* UART not brought out */
+	status = "disabled";
+};
+
+&main_uart6 {
+	/* UART not brought out */
+	status = "disabled";
+};
+
+&main_uart7 {
+	/* UART not brought out */
+	status = "disabled";
+};
+
+&main_uart8 {
+	/* UART not brought out */
+	status = "disabled";
+};
+
+&main_uart9 {
+	/* Brought out on M.2 E Key */
+	status = "disabled";
+};
+
+&main_sdhci0 {
+	/* Unused */
+	status = "disabled";
+};
+
+&main_sdhci1 {
+	/* SD Card */
+	vmmc-supply = <&vdd_mmc1>;
+	vqmmc-supply = <&vdd_sd_dv_alt>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&main_mmc1_pins_default>;
+	ti,driver-strength-ohm = <50>;
+	disable-wp;
+};
+
+&main_sdhci2 {
+	/* Unused */
+	status = "disabled";
+};
+
+&ospi0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&mcu_fss0_ospi0_pins_default>;
+
+	flash@0 {
+		compatible = "jedec,spi-nor";
+		reg = <0x0>;
+		spi-tx-bus-width = <8>;
+		spi-rx-bus-width = <8>;
+		spi-max-frequency = <25000000>;
+		cdns,tshsl-ns = <60>;
+		cdns,tsd2d-ns = <60>;
+		cdns,tchsh-ns = <60>;
+		cdns,tslch-ns = <60>;
+		cdns,read-delay = <4>;
+		#address-cells = <1>;
+		#size-cells = <1>;
+	};
+};
+
+&ospi1 {
+	/* Unused */
+	status = "disabled";
+};
+
+&main_i2c0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&main_i2c0_pins_default>;
+	clock-frequency = <400000>;
+
+	i2c-mux@71 {
+		compatible = "nxp,pca9543";
+		#address-cells = <1>;
+		#size-cells = <0>;
+		reg = <0x71>;
+
+		/* PCIe1 M.2 M Key I2C */
+		i2c@0 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0>;
+		};
+
+		/* PCIe0 M.2 E Key I2C */
+		i2c@1 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <1>;
+		};
+	};
+};
+
+&main_i2c1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&main_i2c1_pins_default>;
+	/* i2c1 is used for DVI DDC, so we need to use 100kHz */
+	clock-frequency = <100000>;
+};
+
+&main_i2c2 {
+	/* Unused */
+	status = "disabled";
+};
+
+&main_i2c3 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&main_i2c3_pins_default>;
+	clock-frequency = <400000>;
+
+	i2c-mux@70 {
+		compatible = "nxp,pca9543";
+		#address-cells = <1>;
+		#size-cells = <0>;
+		reg = <0x70>;
+
+		/* CSI0 I2C */
+		i2c@0 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0>;
+		};
+
+		/* CSI1 I2C */
+		i2c@1 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <1>;
+		};
+	};
+};
+
+&main_i2c4 {
+	/* Unused */
+	status = "disabled";
+};
+
+&main_i2c5 {
+	/* Brought out on RPi Header */
+	status = "disabled";
+};
+
+&main_i2c6 {
+	/* Unused */
+	status = "disabled";
+};
+
+&main_gpio2 {
+	status = "disabled";
+};
+
+&main_gpio3 {
+	status = "disabled";
+};
+
+&main_gpio4 {
+	status = "disabled";
+};
+
+&main_gpio5 {
+	status = "disabled";
+};
+
+&main_gpio6 {
+	status = "disabled";
+};
+
+&main_gpio7 {
+	status = "disabled";
+};
+
+&wkup_gpio1 {
+	status = "disabled";
+};
+
+&main_r5fss0_core0{
+	firmware-name = "pdk-ipc/ipc_echo_test_mcu2_0_release_strip.xer5f";
+};
+
+&usb_serdes_mux {
+	idle-states = <1>, <1>; /* USB0 to SERDES3, USB1 to SERDES2 */
+};
+
+&serdes_ln_ctrl {
+	idle-states = <J721E_SERDES0_LANE0_PCIE0_LANE0>, <J721E_SERDES0_LANE1_IP4_UNUSED>,
+		      <J721E_SERDES1_LANE0_PCIE1_LANE0>, <J721E_SERDES1_LANE1_PCIE1_LANE1>,
+		      <J721E_SERDES2_LANE0_IP1_UNUSED>, <J721E_SERDES2_LANE1_USB3_1>,
+		      <J721E_SERDES3_LANE0_USB3_0_SWAP>, <J721E_SERDES3_LANE1_USB3_0>,
+		      <J721E_SERDES4_LANE0_EDP_LANE0>, <J721E_SERDES4_LANE1_EDP_LANE1>,
+		      <J721E_SERDES4_LANE2_EDP_LANE2>, <J721E_SERDES4_LANE3_EDP_LANE3>;
+};
+
+&serdes_wiz3 {
+	typec-dir-gpios = <&main_gpio1 3 GPIO_ACTIVE_HIGH>;
+	typec-dir-debounce-ms = <700>;	/* TUSB321, tCCB_DEFAULT 133 ms */
+};
+
+&serdes3 {
+	serdes3_usb_link: phy@0 {
+		reg = <0>;
+		cdns,num-lanes = <2>;
+		#phy-cells = <0>;
+		cdns,phy-type = <PHY_TYPE_USB3>;
+		resets = <&serdes_wiz3 1>, <&serdes_wiz3 2>;
+	};
+};
+
+&usbss0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&main_usbss0_pins_default>;
+	ti,vbus-divider;
+};
+
+&usb0 {
+	dr_mode = "otg";
+	maximum-speed = "super-speed";
+	phys = <&serdes3_usb_link>;
+	phy-names = "cdns3,usb3-phy";
+};
+
+&serdes2 {
+	serdes2_usb_link: phy@1 {
+		reg = <1>;
+		cdns,num-lanes = <1>;
+		#phy-cells = <0>;
+		cdns,phy-type = <PHY_TYPE_USB3>;
+		resets = <&serdes_wiz2 2>;
+	};
+};
+
+&usbss1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&main_usbss1_pins_default>;
+	ti,vbus-divider;
+};
+
+&usb1 {
+	dr_mode = "host";
+	maximum-speed = "super-speed";
+	phys = <&serdes2_usb_link>;
+	phy-names = "cdns3,usb3-phy";
+};
+
+&tscadc0 {
+	/* Unused */
+	status = "disabled";
+};
+
+&tscadc1 {
+	/* Unused */
+	status = "disabled";
+};
+
+&mcu_cpsw {
+	pinctrl-names = "default";
+	pinctrl-0 = <&mcu_cpsw_pins_default &mcu_mdio_pins_default>;
+};
+
+&davinci_mdio {
+	phy0: ethernet-phy@0 {
+		reg = <0>;
+		ti,rx-internal-delay = <DP83867_RGMIIDCTL_2_00_NS>;
+		ti,fifo-depth = <DP83867_PHYCR_FIFO_DEPTH_4_B_NIB>;
+	};
+};
+
+&cpsw_port1 {
+	phy-mode = "rgmii-rxid";
+	phy-handle = <&phy0>;
+};
+
+&dss {
+	pinctrl-names = "default";
+	pinctrl-0 = <&dss_vout0_pins_default>;
+
+	assigned-clocks = <&k3_clks 152 1>,	/* VP 1 pixel clock */
+			  <&k3_clks 152 4>,	/* VP 2 pixel clock */
+			  <&k3_clks 152 9>,	/* VP 3 pixel clock */
+			  <&k3_clks 152 13>;	/* VP 4 pixel clock */
+	assigned-clock-parents = <&k3_clks 152 2>,	/* PLL16_HSDIV0 */
+				 <&k3_clks 152 6>,	/* DPI0_EXT_CLKSEL_OUT0 */
+				 <&k3_clks 152 11>,	/* PLL18_HSDIV0 */
+				 <&k3_clks 152 18>;	/* DPI1_EXT_CLKSEL_OUT0 */
+};
+
+&mcasp0 {
+	/* Unused */
+	status = "disabled";
+};
+
+&mcasp1 {
+	/* Unused */
+	status = "disabled";
+};
+
+&mcasp2 {
+	/* Unused */
+	status = "disabled";
+};
+
+&mcasp3 {
+	/* Unused */
+	status = "disabled";
+};
+
+&mcasp4 {
+	/* Unused */
+	status = "disabled";
+};
+
+&mcasp5 {
+	/* Unused */
+	status = "disabled";
+};
+
+&mcasp6 {
+	/* Brought out on RPi header */
+	status = "disabled";
+};
+
+&mcasp7 {
+	/* Unused */
+	status = "disabled";
+};
+
+&mcasp8 {
+	/* Unused */
+	status = "disabled";
+};
+
+&mcasp9 {
+	/* Unused */
+	status = "disabled";
+};
+
+&mcasp10 {
+	/* Unused */
+	status = "disabled";
+};
+
+&mcasp11 {
+	/* Brought out on M.2 E Key */
+	status = "disabled";
+};
+
+&serdes0 {
+	serdes0_pcie_link: phy@0 {
+		reg = <0>;
+		cdns,num-lanes = <1>;
+		#phy-cells = <0>;
+		cdns,phy-type = <PHY_TYPE_PCIE>;
+		resets = <&serdes_wiz0 1>;
+	};
+};
+
+&serdes1 {
+	serdes1_pcie_link: phy@0 {
+		reg = <0>;
+		cdns,num-lanes = <2>;
+		#phy-cells = <0>;
+		cdns,phy-type = <PHY_TYPE_PCIE>;
+		resets = <&serdes_wiz1 1>, <&serdes_wiz1 2>;
+	};
+};
+
+&pcie0_rc {
+	pinctrl-names = "default";
+	pinctrl-0 = <&ekey_reset_pins_default>;
+	reset-gpios = <&main_gpio0 72 GPIO_ACTIVE_HIGH>;
+
+	phys = <&serdes0_pcie_link>;
+	phy-names = "pcie-phy";
+	num-lanes = <1>;
+};
+
+&pcie1_rc {
+	pinctrl-names = "default";
+	pinctrl-0 = <&mkey_reset_pins_default>;
+	reset-gpios = <&wkup_gpio0 11 GPIO_ACTIVE_HIGH>;
+
+	phys = <&serdes1_pcie_link>;
+	phy-names = "pcie-phy";
+	num-lanes = <2>;
+};
+
+&pcie2_rc {
+	/* Unused */
+	status = "disabled";
+};
+
+&pcie0_ep {
+	status = "disabled";
+	phys = <&serdes0_pcie_link>;
+	phy-names = "pcie-phy";
+	num-lanes = <1>;
+};
+
+&pcie1_ep {
+	status = "disabled";
+	phys = <&serdes1_pcie_link>;
+	phy-names = "pcie-phy";
+	num-lanes = <2>;
+};
+
+&pcie2_ep {
+	/* Unused */
+	status = "disabled";
+};
+
+&pcie3_rc {
+	/* Unused */
+	status = "disabled";
+};
+
+&pcie3_ep {
+	/* Unused */
+	status = "disabled";
+};
+
+&dss {
+	status = "disabled";
+};
+
+&icssg0_mdio {
+	status = "disabled";
+};
+
+&icssg1_mdio {
+	status = "disabled";
+};
+
+&ufs_wrapper {
+	status = "disabled";
+};
+
+&mailbox0_cluster0 {
+	interrupts = <436>;
+
+	mbox_mcu_r5fss0_core0: mbox-mcu-r5fss0-core0 {
+		ti,mbox-rx = <0 0 0>;
+		ti,mbox-tx = <1 0 0>;
+	};
+
+	mbox_mcu_r5fss0_core1: mbox-mcu-r5fss0-core1 {
+		ti,mbox-rx = <2 0 0>;
+		ti,mbox-tx = <3 0 0>;
+	};
+};
+
+&mailbox0_cluster1 {
+	interrupts = <432>;
+
+	mbox_main_r5fss0_core0: mbox-main-r5fss0-core0 {
+		ti,mbox-rx = <0 0 0>;
+		ti,mbox-tx = <1 0 0>;
+	};
+
+	mbox_main_r5fss0_core1: mbox-main-r5fss0-core1 {
+		ti,mbox-rx = <2 0 0>;
+		ti,mbox-tx = <3 0 0>;
+	};
+};
+
+&mailbox0_cluster2 {
+	interrupts = <428>;
+
+	mbox_main_r5fss1_core0: mbox-main-r5fss1-core0 {
+		ti,mbox-rx = <0 0 0>;
+		ti,mbox-tx = <1 0 0>;
+	};
+
+	mbox_main_r5fss1_core1: mbox-main-r5fss1-core1 {
+		ti,mbox-rx = <2 0 0>;
+		ti,mbox-tx = <3 0 0>;
+	};
+};
+
+&mailbox0_cluster3 {
+	interrupts = <424>;
+
+	mbox_c66_0: mbox-c66-0 {
+		ti,mbox-rx = <0 0 0>;
+		ti,mbox-tx = <1 0 0>;
+	};
+
+	mbox_c66_1: mbox-c66-1 {
+		ti,mbox-rx = <2 0 0>;
+		ti,mbox-tx = <3 0 0>;
+	};
+};
+
+&mailbox0_cluster4 {
+	interrupts = <420>;
+
+	mbox_c71_0: mbox-c71-0 {
+		ti,mbox-rx = <0 0 0>;
+		ti,mbox-tx = <1 0 0>;
+	};
+};
+
+&mailbox0_cluster5 {
+	status = "disabled";
+};
+
+&mailbox0_cluster6 {
+	status = "disabled";
+};
+
+&mailbox0_cluster7 {
+	status = "disabled";
+};
+
+&mailbox0_cluster8 {
+	status = "disabled";
+};
+
+&mailbox0_cluster9 {
+	status = "disabled";
+};
+
+&mailbox0_cluster10 {
+	status = "disabled";
+};
+
+&mailbox0_cluster11 {
+	status = "disabled";
+};
+
+&mcu_r5fss0_core0 {
+	mboxes = <&mailbox0_cluster0 &mbox_mcu_r5fss0_core0>;
+	memory-region = <&mcu_r5fss0_core0_dma_memory_region>,
+			<&mcu_r5fss0_core0_memory_region>;
+};
+
+&mcu_r5fss0_core1 {
+	mboxes = <&mailbox0_cluster0 &mbox_mcu_r5fss0_core1>;
+	memory-region = <&mcu_r5fss0_core1_dma_memory_region>,
+			<&mcu_r5fss0_core1_memory_region>;
+};
+
+&main_r5fss0_core0 {
+	mboxes = <&mailbox0_cluster1 &mbox_main_r5fss0_core0>;
+	memory-region = <&main_r5fss0_core0_dma_memory_region>,
+			<&main_r5fss0_core0_memory_region>;
+};
+
+&main_r5fss0_core1 {
+	mboxes = <&mailbox0_cluster1 &mbox_main_r5fss0_core1>;
+	memory-region = <&main_r5fss0_core1_dma_memory_region>,
+			<&main_r5fss0_core1_memory_region>;
+};
+
+&main_r5fss1_core0 {
+	mboxes = <&mailbox0_cluster2 &mbox_main_r5fss1_core0>;
+	memory-region = <&main_r5fss1_core0_dma_memory_region>,
+			<&main_r5fss1_core0_memory_region>;
+};
+
+&main_r5fss1_core1 {
+	mboxes = <&mailbox0_cluster2 &mbox_main_r5fss1_core1>;
+	memory-region = <&main_r5fss1_core1_dma_memory_region>,
+			<&main_r5fss1_core1_memory_region>;
+};
+
+&c66_0 {
+	mboxes = <&mailbox0_cluster3 &mbox_c66_0>;
+	memory-region = <&c66_0_dma_memory_region>,
+			<&c66_0_memory_region>;
+};
+
+&c66_1 {
+	mboxes = <&mailbox0_cluster3 &mbox_c66_1>;
+	memory-region = <&c66_1_dma_memory_region>,
+			<&c66_1_memory_region>;
+};
+
+&c71_0 {
+	mboxes = <&mailbox0_cluster4 &mbox_c71_0>;
+	memory-region = <&c71_0_dma_memory_region>,
+			<&c71_0_memory_region>;
+};
diff --git a/arch/arm64/boot/dts/ti/k3-j721e.dtsi b/arch/arm64/boot/dts/ti/k3-j721e.dtsi
index f0587fde147e..214359e7288b 100644
--- a/arch/arm64/boot/dts/ti/k3-j721e.dtsi
+++ b/arch/arm64/boot/dts/ti/k3-j721e.dtsi
@@ -31,6 +31,9 @@
 		serial10 = &main_uart8;
 		serial11 = &main_uart9;
 		ethernet0 = &cpsw_port1;
+		mmc0 = &main_sdhci0;
+		mmc1 = &main_sdhci1;
+		mmc2 = &main_sdhci2;
 	};
 
 	chosen { };
diff --git a/arch/arm64/boot/dts/toshiba/Makefile b/arch/arm64/boot/dts/toshiba/Makefile
index 8cd460d5b68e..7ccb4664bb37 100644
--- a/arch/arm64/boot/dts/toshiba/Makefile
+++ b/arch/arm64/boot/dts/toshiba/Makefile
@@ -1,2 +1,3 @@
 # SPDX-License-Identifier: GPL-2.0
 dtb-$(CONFIG_ARCH_VISCONTI) += tmpv7708-rm-mbrc.dtb
+dtb-$(CONFIG_ARCH_VISCONTI) += tmpv7708-visrobo-vrb.dtb
diff --git a/arch/arm64/boot/dts/toshiba/tmpv7708-rm-mbrc.dts b/arch/arm64/boot/dts/toshiba/tmpv7708-rm-mbrc.dts
index 29a4d9fc1e47..9375b0faeea2 100644
--- a/arch/arm64/boot/dts/toshiba/tmpv7708-rm-mbrc.dts
+++ b/arch/arm64/boot/dts/toshiba/tmpv7708-rm-mbrc.dts
@@ -76,3 +76,9 @@
 &pwm {
 	status = "okay";
 };
+
+&pcie {
+	status = "okay";
+	clocks = <&extclk100mhz>, <&clk600mhz>, <&clk25mhz>;
+	clock-names = "ref", "core", "aux";
+};
diff --git a/arch/arm64/boot/dts/toshiba/tmpv7708-visrobo-vrb.dts b/arch/arm64/boot/dts/toshiba/tmpv7708-visrobo-vrb.dts
new file mode 100644
index 000000000000..d0817463706e
--- /dev/null
+++ b/arch/arm64/boot/dts/toshiba/tmpv7708-visrobo-vrb.dts
@@ -0,0 +1,61 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Device Tree File for TMPV7708 VisROBO VRB board
+ *
+ * (C) Copyright 2020, 2021, Toshiba Corporation.
+ * (C) Copyright 2020, Nobuhiro Iwamatsu <nobuhiro1.iwamatsu@toshiba.co.jp>
+ */
+
+/dts-v1/;
+
+#include "tmpv7708-visrobo-vrc.dtsi"
+
+/ {
+	model = "Toshiba TMPV7708 VisROBO (VRB) board";
+	compatible = "toshiba,tmpv7708-visrobo-vrb", "toshiba,tmpv7708";
+
+	aliases {
+		serial0 = &uart0;
+		serial1 = &uart1;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	/* 768MB memory */
+	memory@80000000 {
+		device_type = "memory";
+		reg = <0x0 0x80000000 0x0 0x30000000>;
+	};
+};
+
+&uart0 {
+	status = "okay";
+	clocks = <&uart_clk>;
+	clock-names = "apb_pclk";
+};
+
+&uart1 {
+	status = "okay";
+	clocks = <&uart_clk>;
+	clock-names = "apb_pclk";
+};
+
+&piether {
+	status = "okay";
+	phy-handle = <&phy0>;
+	phy-mode = "rgmii-id";
+	clocks = <&clk300mhz>, <&clk125mhz>;
+	clock-names = "stmmaceth", "phy_ref_clk";
+
+	mdio0 {
+		#address-cells = <1>;
+		#size-cells = <0>;
+		compatible = "snps,dwmac-mdio";
+		phy0: ethernet-phy@1 {
+			device_type = "ethernet-phy";
+			reg = <0x1>;
+		};
+	};
+};
diff --git a/arch/arm64/boot/dts/toshiba/tmpv7708-visrobo-vrc.dtsi b/arch/arm64/boot/dts/toshiba/tmpv7708-visrobo-vrc.dtsi
new file mode 100644
index 000000000000..f0a93db6dde6
--- /dev/null
+++ b/arch/arm64/boot/dts/toshiba/tmpv7708-visrobo-vrc.dtsi
@@ -0,0 +1,44 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Device Tree File for TMPV7708 VisROBO VRC SoM
+ *
+ * (C) Copyright 2020, 2021, Toshiba Corporation.
+ * (C) Copyright 2020, Nobuhiro Iwamatsu <nobuhiro1.iwamatsu@toshiba.co.jp>
+ */
+
+/dts-v1/;
+
+#include "tmpv7708.dtsi"
+#include <dt-bindings/gpio/gpio.h>
+
+&wdt {
+	status = "okay";
+	clocks = <&wdt_clk>;
+};
+
+&gpio {
+	status = "okay";
+};
+
+&spi0_pins {
+	groups = "spi0_grp", "spi0_cs0_grp";
+};
+
+&spi0 {
+	status = "okay";
+	clocks = <&clk300mhz>, <&clk150mhz>;
+	clock-names = "sspclk", "apb_pclk";
+
+	mmc-slot@0 {
+		compatible = "mmc-spi-slot";
+		reg = <0>;
+		gpios = <&gpio 15 GPIO_ACTIVE_LOW>;
+		voltage-ranges = <3200 3400>;
+		spi-max-frequency = <12000000>;
+	};
+};
+
+&i2c0 {
+	status = "okay";
+	clocks = <&clk150mhz>;
+};
diff --git a/arch/arm64/boot/dts/toshiba/tmpv7708.dtsi b/arch/arm64/boot/dts/toshiba/tmpv7708.dtsi
index 4b4231ff43cf..01d7ee61ad25 100644
--- a/arch/arm64/boot/dts/toshiba/tmpv7708.dtsi
+++ b/arch/arm64/boot/dts/toshiba/tmpv7708.dtsi
@@ -134,6 +134,13 @@
 		#clock-cells = <0>;
 	};
 
+	clk25mhz: clk25mhz {
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <25000000>;
+		clock-output-names = "clk25mhz";
+	};
+
 	clk125mhz: clk125mhz {
 		compatible = "fixed-clock";
 		clock-frequency = <125000000>;
@@ -141,6 +148,13 @@
 		clock-output-names = "clk125mhz";
 	};
 
+	clk150mhz: clk150mhz {
+		compatible = "fixed-clock";
+		clock-frequency = <150000000>;
+		#clock-cells = <0>;
+		clock-output-names = "clk150mhz";
+	};
+
 	clk300mhz: clk300mhz {
 		compatible = "fixed-clock";
 		clock-frequency = <300000000>;
@@ -148,6 +162,20 @@
 		clock-output-names = "clk300mhz";
 	};
 
+	clk600mhz: clk600mhz {
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <600000000>;
+		clock-output-names = "clk600mhz";
+	};
+
+	extclk100mhz: extclk100mhz {
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <100000000>;
+		clock-output-names = "extclk100mhz";
+	};
+
 	wdt_clk: wdt-clk {
 		compatible = "fixed-clock";
 		clock-frequency = <150000000>;
@@ -441,6 +469,37 @@
 			#pwm-cells = <2>;
 			status = "disabled";
 		};
+
+		pcie: pcie@28400000 {
+			compatible = "toshiba,visconti-pcie";
+			reg = <0x0 0x28400000 0x0 0x00400000>,
+			      <0x0 0x70000000 0x0 0x10000000>,
+			      <0x0 0x28050000 0x0 0x00010000>,
+			      <0x0 0x24200000 0x0 0x00002000>,
+			      <0x0 0x24162000 0x0 0x00001000>;
+			reg-names  = "dbi", "config", "ulreg", "smu", "mpu";
+			device_type = "pci";
+			bus-range = <0x00 0xff>;
+			num-lanes = <2>;
+			num-viewport = <8>;
+
+			#address-cells = <3>;
+			#size-cells = <2>;
+			#interrupt-cells = <1>;
+			ranges = <0x81000000 0 0x40000000 0 0x40000000 0 0x00010000
+				  0x82000000 0 0x50000000 0 0x50000000 0 0x20000000>;
+			interrupts = <GIC_SPI 211 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 215 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "msi", "intr";
+			interrupt-map-mask = <0 0 0 7>;
+			interrupt-map =
+				<0 0 0 1 &gic GIC_SPI 215 IRQ_TYPE_LEVEL_HIGH
+				 0 0 0 2 &gic GIC_SPI 215 IRQ_TYPE_LEVEL_HIGH
+				 0 0 0 3 &gic GIC_SPI 215 IRQ_TYPE_LEVEL_HIGH
+				 0 0 0 4 &gic GIC_SPI 215 IRQ_TYPE_LEVEL_HIGH>;
+			max-link-speed = <2>;
+			status = "disabled";
+		};
 	};
 };
 
diff --git a/arch/arm64/boot/dts/xilinx/Makefile b/arch/arm64/boot/dts/xilinx/Makefile
index 11fb4fd3ebd4..4e159540d031 100644
--- a/arch/arm64/boot/dts/xilinx/Makefile
+++ b/arch/arm64/boot/dts/xilinx/Makefile
@@ -12,7 +12,21 @@ dtb-$(CONFIG_ARCH_ZYNQMP) += zynqmp-zcu100-revC.dtb
 dtb-$(CONFIG_ARCH_ZYNQMP) += zynqmp-zcu102-revA.dtb
 dtb-$(CONFIG_ARCH_ZYNQMP) += zynqmp-zcu102-revB.dtb
 dtb-$(CONFIG_ARCH_ZYNQMP) += zynqmp-zcu102-rev1.0.dtb
+dtb-$(CONFIG_ARCH_ZYNQMP) += zynqmp-zcu102-rev1.1.dtb
 dtb-$(CONFIG_ARCH_ZYNQMP) += zynqmp-zcu104-revA.dtb
 dtb-$(CONFIG_ARCH_ZYNQMP) += zynqmp-zcu104-revC.dtb
 dtb-$(CONFIG_ARCH_ZYNQMP) += zynqmp-zcu106-revA.dtb
 dtb-$(CONFIG_ARCH_ZYNQMP) += zynqmp-zcu111-revA.dtb
+
+dtb-$(CONFIG_ARCH_ZYNQMP) += zynqmp-sm-k26-revA.dtb
+dtb-$(CONFIG_ARCH_ZYNQMP) += zynqmp-smk-k26-revA.dtb
+
+sm-k26-revA-sck-kv-g-revA-dtbs := zynqmp-sm-k26-revA.dtb zynqmp-sck-kv-g-revA.dtbo
+sm-k26-revA-sck-kv-g-revB-dtbs := zynqmp-sm-k26-revA.dtb zynqmp-sck-kv-g-revB.dtbo
+smk-k26-revA-sm-k26-revA-sck-kv-g-revA-dtbs := zynqmp-smk-k26-revA.dtb zynqmp-sck-kv-g-revA.dtbo
+smk-k26-revA-sm-k26-revA-sck-kv-g-revB-dtbs := zynqmp-smk-k26-revA.dtb zynqmp-sck-kv-g-revB.dtbo
+
+dtb-$(CONFIG_ARCH_ZYNQMP) += sm-k26-revA-sck-kv-g-revA.dtb
+dtb-$(CONFIG_ARCH_ZYNQMP) += sm-k26-revA-sck-kv-g-revB.dtb
+dtb-$(CONFIG_ARCH_ZYNQMP) += smk-k26-revA-sm-k26-revA-sck-kv-g-revA.dtb
+dtb-$(CONFIG_ARCH_ZYNQMP) += smk-k26-revA-sm-k26-revA-sck-kv-g-revB.dtb
diff --git a/arch/arm64/boot/dts/xilinx/zynqmp-clk-ccf.dtsi b/arch/arm64/boot/dts/xilinx/zynqmp-clk-ccf.dtsi
index cf5295224750..1e0b1bca7c94 100644
--- a/arch/arm64/boot/dts/xilinx/zynqmp-clk-ccf.dtsi
+++ b/arch/arm64/boot/dts/xilinx/zynqmp-clk-ccf.dtsi
@@ -2,7 +2,7 @@
 /*
  * Clock specification for Xilinx ZynqMP
  *
- * (C) Copyright 2017 - 2019, Xilinx, Inc.
+ * (C) Copyright 2017 - 2021, Xilinx, Inc.
  *
  * Michal Simek <michal.simek@xilinx.com>
  */
@@ -40,6 +40,17 @@
 	};
 };
 
+&zynqmp_firmware {
+	zynqmp_clk: clock-controller {
+		#clock-cells = <1>;
+		compatible = "xlnx,zynqmp-clk";
+		clocks = <&pss_ref_clk>, <&video_clk>, <&pss_alt_ref_clk>,
+			 <&aux_ref_clk>, <&gt_crx_ref_clk>;
+		clock-names = "pss_ref_clk", "video_clk", "pss_alt_ref_clk",
+			      "aux_ref_clk", "gt_crx_ref_clk";
+	};
+};
+
 &can0 {
 	clocks = <&zynqmp_clk CAN0_REF>, <&zynqmp_clk LPD_LSBUS>;
 };
diff --git a/arch/arm64/boot/dts/xilinx/zynqmp-sck-kv-g-revA.dts b/arch/arm64/boot/dts/xilinx/zynqmp-sck-kv-g-revA.dts
new file mode 100644
index 000000000000..b610e65e0cdf
--- /dev/null
+++ b/arch/arm64/boot/dts/xilinx/zynqmp-sck-kv-g-revA.dts
@@ -0,0 +1,315 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * dts file for KV260 revA Carrier Card
+ *
+ * (C) Copyright 2020 - 2021, Xilinx, Inc.
+ *
+ * SD level shifter:
+ * "A" – A01 board un-modified (NXP)
+ * "Y" – A01 board modified with legacy interposer (Nexperia)
+ * "Z" – A01 board modified with Diode interposer
+ *
+ * Michal Simek <michal.simek@xilinx.com>
+ */
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/net/ti-dp83867.h>
+#include <dt-bindings/phy/phy.h>
+#include <dt-bindings/pinctrl/pinctrl-zynqmp.h>
+
+/dts-v1/;
+/plugin/;
+
+&i2c1 { /* I2C_SCK C23/C24 - MIO from SOM */
+	#address-cells = <1>;
+	#size-cells = <0>;
+	pinctrl-names = "default", "gpio";
+	pinctrl-0 = <&pinctrl_i2c1_default>;
+	pinctrl-1 = <&pinctrl_i2c1_gpio>;
+	scl-gpios = <&gpio 24 GPIO_ACTIVE_HIGH>;
+	sda-gpios = <&gpio 25 GPIO_ACTIVE_HIGH>;
+
+	/* u14 - 0x40 - ina260 */
+	/* u27 - 0xe0 - STDP4320 DP/HDMI splitter */
+};
+
+&amba {
+	si5332_0: si5332_0 { /* u17 */
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <125000000>;
+	};
+
+	si5332_1: si5332_1 { /* u17 */
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <25000000>;
+	};
+
+	si5332_2: si5332_2 { /* u17 */
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <48000000>;
+	};
+
+	si5332_3: si5332_3 { /* u17 */
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <24000000>;
+	};
+
+	si5332_4: si5332_4 { /* u17 */
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <26000000>;
+	};
+
+	si5332_5: si5332_5 { /* u17 */
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <27000000>;
+	};
+};
+
+/* DP/USB 3.0 and SATA */
+&psgtr {
+	status = "okay";
+	/* pcie, usb3, sata */
+	clocks = <&si5332_5>, <&si5332_4>, <&si5332_0>;
+	clock-names = "ref0", "ref1", "ref2";
+};
+
+&sata {
+	status = "okay";
+	/* SATA OOB timing settings */
+	ceva,p0-cominit-params = /bits/ 8 <0x18 0x40 0x18 0x28>;
+	ceva,p0-comwake-params = /bits/ 8 <0x06 0x14 0x08 0x0E>;
+	ceva,p0-burst-params = /bits/ 8 <0x13 0x08 0x4A 0x06>;
+	ceva,p0-retry-params = /bits/ 16 <0x96A4 0x3FFC>;
+	ceva,p1-cominit-params = /bits/ 8 <0x18 0x40 0x18 0x28>;
+	ceva,p1-comwake-params = /bits/ 8 <0x06 0x14 0x08 0x0E>;
+	ceva,p1-burst-params = /bits/ 8 <0x13 0x08 0x4A 0x06>;
+	ceva,p1-retry-params = /bits/ 16 <0x96A4 0x3FFC>;
+	phy-names = "sata-phy";
+	phys = <&psgtr 3 PHY_TYPE_SATA 1 2>;
+};
+
+&zynqmp_dpsub {
+	status = "disabled";
+	phy-names = "dp-phy0", "dp-phy1";
+	phys = <&psgtr 1 PHY_TYPE_DP 0 0>, <&psgtr 0 PHY_TYPE_DP 1 0>;
+};
+
+&zynqmp_dpdma {
+	status = "okay";
+};
+
+&usb0 {
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usb0_default>;
+	phy-names = "usb3-phy";
+	phys = <&psgtr 2 PHY_TYPE_USB3 0 1>;
+	/* missing usb5744 - u43 */
+};
+
+&dwc3_0 {
+	status = "okay";
+	dr_mode = "host";
+	snps,usb3_lpm_capable;
+	maximum-speed = "super-speed";
+};
+
+&sdhci1 { /* on CC with tuned parameters */
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_sdhci1_default>;
+	/*
+	 * SD 3.0 requires level shifter and this property
+	 * should be removed if the board has level shifter and
+	 * need to work in UHS mode
+	 */
+	no-1-8-v;
+	disable-wp;
+	xlnx,mio-bank = <1>;
+};
+
+&gem3 { /* required by spec */
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_gem3_default>;
+	phy-handle = <&phy0>;
+	phy-mode = "rgmii-id";
+
+	mdio: mdio {
+		#address-cells = <1>;
+		#size-cells = <0>;
+		reset-gpios = <&gpio 38 GPIO_ACTIVE_LOW>;
+		reset-delay-us = <2>;
+
+		phy0: ethernet-phy@1 {
+			#phy-cells = <1>;
+			reg = <1>;
+			ti,rx-internal-delay = <DP83867_RGMIIDCTL_2_25_NS>;
+			ti,tx-internal-delay = <DP83867_RGMIIDCTL_2_75_NS>;
+			ti,fifo-depth = <DP83867_PHYCR_FIFO_DEPTH_4_B_NIB>;
+			ti,dp83867-rxctrl-strap-quirk;
+		};
+	};
+};
+
+&pinctrl0 { /* required by spec */
+	status = "okay";
+
+	pinctrl_uart1_default: uart1-default {
+		conf {
+			groups = "uart1_9_grp";
+			slew-rate = <SLEW_RATE_SLOW>;
+			power-source = <IO_STANDARD_LVCMOS18>;
+			drive-strength = <12>;
+		};
+
+		conf-rx {
+			pins = "MIO37";
+			bias-high-impedance;
+		};
+
+		conf-tx {
+			pins = "MIO36";
+			bias-disable;
+		};
+
+		mux {
+			groups = "uart1_9_grp";
+			function = "uart1";
+		};
+	};
+
+	pinctrl_i2c1_default: i2c1-default {
+		conf {
+			groups = "i2c1_6_grp";
+			bias-pull-up;
+			slew-rate = <SLEW_RATE_SLOW>;
+			power-source = <IO_STANDARD_LVCMOS18>;
+		};
+
+		mux {
+			groups = "i2c1_6_grp";
+			function = "i2c1";
+		};
+	};
+
+	pinctrl_i2c1_gpio: i2c1-gpio {
+		conf {
+			groups = "gpio0_24_grp", "gpio0_25_grp";
+			slew-rate = <SLEW_RATE_SLOW>;
+			power-source = <IO_STANDARD_LVCMOS18>;
+		};
+
+		mux {
+			groups = "gpio0_24_grp", "gpio0_25_grp";
+			function = "gpio0";
+		};
+	};
+
+	pinctrl_gem3_default: gem3-default {
+		conf {
+			groups = "ethernet3_0_grp";
+			slew-rate = <SLEW_RATE_SLOW>;
+			power-source = <IO_STANDARD_LVCMOS18>;
+		};
+
+		conf-rx {
+			pins = "MIO70", "MIO72", "MIO74";
+			bias-high-impedance;
+			low-power-disable;
+		};
+
+		conf-bootstrap {
+			pins = "MIO71", "MIO73", "MIO75";
+			bias-disable;
+			low-power-disable;
+		};
+
+		conf-tx {
+			pins = "MIO64", "MIO65", "MIO66",
+				"MIO67", "MIO68", "MIO69";
+			bias-disable;
+			low-power-enable;
+		};
+
+		conf-mdio {
+			groups = "mdio3_0_grp";
+			slew-rate = <SLEW_RATE_SLOW>;
+			power-source = <IO_STANDARD_LVCMOS18>;
+			bias-disable;
+		};
+
+		mux-mdio {
+			function = "mdio3";
+			groups = "mdio3_0_grp";
+		};
+
+		mux {
+			function = "ethernet3";
+			groups = "ethernet3_0_grp";
+		};
+	};
+
+	pinctrl_usb0_default: usb0-default {
+		conf {
+			groups = "usb0_0_grp";
+			slew-rate = <SLEW_RATE_SLOW>;
+			power-source = <IO_STANDARD_LVCMOS18>;
+		};
+
+		conf-rx {
+			pins = "MIO52", "MIO53", "MIO55";
+			bias-high-impedance;
+		};
+
+		conf-tx {
+			pins = "MIO54", "MIO56", "MIO57", "MIO58", "MIO59",
+			"MIO60", "MIO61", "MIO62", "MIO63";
+			bias-disable;
+		};
+
+		mux {
+			groups = "usb0_0_grp";
+			function = "usb0";
+		};
+	};
+
+	pinctrl_sdhci1_default: sdhci1-default {
+		conf {
+			groups = "sdio1_0_grp";
+			slew-rate = <SLEW_RATE_SLOW>;
+			power-source = <IO_STANDARD_LVCMOS18>;
+			bias-disable;
+		};
+
+		conf-cd {
+			groups = "sdio1_cd_0_grp";
+			bias-high-impedance;
+			bias-pull-up;
+			slew-rate = <SLEW_RATE_SLOW>;
+			power-source = <IO_STANDARD_LVCMOS18>;
+		};
+
+		mux-cd {
+			groups = "sdio1_cd_0_grp";
+			function = "sdio1_cd";
+		};
+
+		mux {
+			groups = "sdio1_0_grp";
+			function = "sdio1";
+		};
+	};
+};
+
+&uart1 {
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart1_default>;
+};
diff --git a/arch/arm64/boot/dts/xilinx/zynqmp-sck-kv-g-revB.dts b/arch/arm64/boot/dts/xilinx/zynqmp-sck-kv-g-revB.dts
new file mode 100644
index 000000000000..a52dafbfd59e
--- /dev/null
+++ b/arch/arm64/boot/dts/xilinx/zynqmp-sck-kv-g-revB.dts
@@ -0,0 +1,298 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * dts file for KV260 revA Carrier Card
+ *
+ * (C) Copyright 2020 - 2021, Xilinx, Inc.
+ *
+ * Michal Simek <michal.simek@xilinx.com>
+ */
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/net/ti-dp83867.h>
+#include <dt-bindings/phy/phy.h>
+#include <dt-bindings/pinctrl/pinctrl-zynqmp.h>
+
+/dts-v1/;
+/plugin/;
+
+&i2c1 { /* I2C_SCK C23/C24 - MIO from SOM */
+	#address-cells = <1>;
+	#size-cells = <0>;
+	pinctrl-names = "default", "gpio";
+	pinctrl-0 = <&pinctrl_i2c1_default>;
+	pinctrl-1 = <&pinctrl_i2c1_gpio>;
+	scl-gpios = <&gpio 24 GPIO_ACTIVE_HIGH>;
+	sda-gpios = <&gpio 25 GPIO_ACTIVE_HIGH>;
+
+	/* u14 - 0x40 - ina260 */
+	/* u43 - 0x2d - usb5744 */
+	/* u27 - 0xe0 - STDP4320 DP/HDMI splitter */
+};
+
+&amba {
+	si5332_0: si5332_0 { /* u17 */
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <125000000>;
+	};
+
+	si5332_1: si5332_1 { /* u17 */
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <25000000>;
+	};
+
+	si5332_2: si5332_2 { /* u17 */
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <48000000>;
+	};
+
+	si5332_3: si5332_3 { /* u17 */
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <24000000>;
+	};
+
+	si5332_4: si5332_4 { /* u17 */
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <26000000>;
+	};
+
+	si5332_5: si5332_5 { /* u17 */
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <27000000>;
+	};
+};
+
+/* DP/USB 3.0 */
+&psgtr {
+	status = "okay";
+	/* pcie, usb3, sata */
+	clocks = <&si5332_5>, <&si5332_4>, <&si5332_0>;
+	clock-names = "ref0", "ref1", "ref2";
+};
+
+&zynqmp_dpsub {
+	status = "disabled";
+	phy-names = "dp-phy0", "dp-phy1";
+	phys = <&psgtr 1 PHY_TYPE_DP 0 0>, <&psgtr 0 PHY_TYPE_DP 1 0>;
+};
+
+&zynqmp_dpdma {
+	status = "okay";
+};
+
+&usb0 {
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usb0_default>;
+	phy-names = "usb3-phy";
+	phys = <&psgtr 2 PHY_TYPE_USB3 0 1>;
+};
+
+&dwc3_0 {
+	status = "okay";
+	dr_mode = "host";
+	snps,usb3_lpm_capable;
+	maximum-speed = "super-speed";
+};
+
+&sdhci1 { /* on CC with tuned parameters */
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_sdhci1_default>;
+	/*
+	 * SD 3.0 requires level shifter and this property
+	 * should be removed if the board has level shifter and
+	 * need to work in UHS mode
+	 */
+	no-1-8-v;
+	disable-wp;
+	xlnx,mio-bank = <1>;
+	clk-phase-sd-hs = <126>, <60>;
+	clk-phase-uhs-sdr25 = <120>, <60>;
+	clk-phase-uhs-ddr50 = <126>, <48>;
+};
+
+&gem3 { /* required by spec */
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_gem3_default>;
+	phy-handle = <&phy0>;
+	phy-mode = "rgmii-id";
+
+	mdio: mdio {
+		#address-cells = <1>;
+		#size-cells = <0>;
+		reset-gpios = <&gpio 38 GPIO_ACTIVE_LOW>;
+		reset-delay-us = <2>;
+
+		phy0: ethernet-phy@1 {
+			#phy-cells = <1>;
+			reg = <1>;
+			ti,rx-internal-delay = <DP83867_RGMIIDCTL_2_25_NS>;
+			ti,tx-internal-delay = <DP83867_RGMIIDCTL_2_75_NS>;
+			ti,fifo-depth = <DP83867_PHYCR_FIFO_DEPTH_4_B_NIB>;
+			ti,dp83867-rxctrl-strap-quirk;
+		};
+	};
+};
+
+&pinctrl0 { /* required by spec */
+	status = "okay";
+
+	pinctrl_uart1_default: uart1-default {
+		conf {
+			groups = "uart1_9_grp";
+			slew-rate = <SLEW_RATE_SLOW>;
+			power-source = <IO_STANDARD_LVCMOS18>;
+			drive-strength = <12>;
+		};
+
+		conf-rx {
+			pins = "MIO37";
+			bias-high-impedance;
+		};
+
+		conf-tx {
+			pins = "MIO36";
+			bias-disable;
+		};
+
+		mux {
+			groups = "uart1_9_grp";
+			function = "uart1";
+		};
+	};
+
+	pinctrl_i2c1_default: i2c1-default {
+		conf {
+			groups = "i2c1_6_grp";
+			bias-pull-up;
+			slew-rate = <SLEW_RATE_SLOW>;
+			power-source = <IO_STANDARD_LVCMOS18>;
+		};
+
+		mux {
+			groups = "i2c1_6_grp";
+			function = "i2c1";
+		};
+	};
+
+	pinctrl_i2c1_gpio: i2c1-gpio {
+		conf {
+			groups = "gpio0_24_grp", "gpio0_25_grp";
+			slew-rate = <SLEW_RATE_SLOW>;
+			power-source = <IO_STANDARD_LVCMOS18>;
+		};
+
+		mux {
+			groups = "gpio0_24_grp", "gpio0_25_grp";
+			function = "gpio0";
+		};
+	};
+
+	pinctrl_gem3_default: gem3-default {
+		conf {
+			groups = "ethernet3_0_grp";
+			slew-rate = <SLEW_RATE_SLOW>;
+			power-source = <IO_STANDARD_LVCMOS18>;
+		};
+
+		conf-rx {
+			pins = "MIO70", "MIO72", "MIO74";
+			bias-high-impedance;
+			low-power-disable;
+		};
+
+		conf-bootstrap {
+			pins = "MIO71", "MIO73", "MIO75";
+			bias-disable;
+			low-power-disable;
+		};
+
+		conf-tx {
+			pins = "MIO64", "MIO65", "MIO66",
+				"MIO67", "MIO68", "MIO69";
+			bias-disable;
+			low-power-enable;
+		};
+
+		conf-mdio {
+			groups = "mdio3_0_grp";
+			slew-rate = <SLEW_RATE_SLOW>;
+			power-source = <IO_STANDARD_LVCMOS18>;
+			bias-disable;
+		};
+
+		mux-mdio {
+			function = "mdio3";
+			groups = "mdio3_0_grp";
+		};
+
+		mux {
+			function = "ethernet3";
+			groups = "ethernet3_0_grp";
+		};
+	};
+
+	pinctrl_usb0_default: usb0-default {
+		conf {
+			groups = "usb0_0_grp";
+			slew-rate = <SLEW_RATE_SLOW>;
+			power-source = <IO_STANDARD_LVCMOS18>;
+		};
+
+		conf-rx {
+			pins = "MIO52", "MIO53", "MIO55";
+			bias-high-impedance;
+		};
+
+		conf-tx {
+			pins = "MIO54", "MIO56", "MIO57", "MIO58", "MIO59",
+			"MIO60", "MIO61", "MIO62", "MIO63";
+			bias-disable;
+		};
+
+		mux {
+			groups = "usb0_0_grp";
+			function = "usb0";
+		};
+	};
+
+	pinctrl_sdhci1_default: sdhci1-default {
+		conf {
+			groups = "sdio1_0_grp";
+			slew-rate = <SLEW_RATE_SLOW>;
+			power-source = <IO_STANDARD_LVCMOS18>;
+			bias-disable;
+		};
+
+		conf-cd {
+			groups = "sdio1_cd_0_grp";
+			bias-high-impedance;
+			bias-pull-up;
+			slew-rate = <SLEW_RATE_SLOW>;
+			power-source = <IO_STANDARD_LVCMOS18>;
+		};
+
+		mux-cd {
+			groups = "sdio1_cd_0_grp";
+			function = "sdio1_cd";
+		};
+
+		mux {
+			groups = "sdio1_0_grp";
+			function = "sdio1";
+		};
+	};
+};
+
+&uart1 {
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart1_default>;
+};
diff --git a/arch/arm64/boot/dts/xilinx/zynqmp-sm-k26-revA.dts b/arch/arm64/boot/dts/xilinx/zynqmp-sm-k26-revA.dts
new file mode 100644
index 000000000000..550b389153e6
--- /dev/null
+++ b/arch/arm64/boot/dts/xilinx/zynqmp-sm-k26-revA.dts
@@ -0,0 +1,289 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * dts file for Xilinx ZynqMP SM-K26 rev1/B/A
+ *
+ * (C) Copyright 2020 - 2021, Xilinx, Inc.
+ *
+ * Michal Simek <michal.simek@xilinx.com>
+ */
+
+/dts-v1/;
+
+#include "zynqmp.dtsi"
+#include "zynqmp-clk-ccf.dtsi"
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/phy/phy.h>
+
+/ {
+	model = "ZynqMP SM-K26 Rev1/B/A";
+	compatible = "xlnx,zynqmp-sm-k26-rev1", "xlnx,zynqmp-sm-k26-revB",
+		     "xlnx,zynqmp-sm-k26-revA", "xlnx,zynqmp-sm-k26",
+		     "xlnx,zynqmp";
+
+	aliases {
+		i2c0 = &i2c0;
+		i2c1 = &i2c1;
+		mmc0 = &sdhci0;
+		mmc1 = &sdhci1;
+		nvmem0 = &eeprom;
+		nvmem1 = &eeprom_cc;
+		rtc0 = &rtc;
+		serial0 = &uart0;
+		serial1 = &uart1;
+		serial2 = &dcc;
+		spi0 = &qspi;
+		spi1 = &spi0;
+		spi2 = &spi1;
+		usb0 = &usb0;
+		usb1 = &usb1;
+	};
+
+	chosen {
+		bootargs = "earlycon";
+		stdout-path = "serial1:115200n8";
+	};
+
+	memory@0 {
+		device_type = "memory"; /* 4GB */
+		reg = <0x0 0x0 0x0 0x80000000>, <0x8 0x00000000 0x0 0x80000000>;
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+		autorepeat;
+		fwuen {
+			label = "fwuen";
+			gpios = <&gpio 12 GPIO_ACTIVE_LOW>;
+		};
+	};
+
+	leds {
+		compatible = "gpio-leds";
+		ds35-led {
+			label = "heartbeat";
+			gpios = <&gpio 7 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "heartbeat";
+		};
+
+		ds36-led {
+			label = "vbus_det";
+			gpios = <&gpio 8 GPIO_ACTIVE_HIGH>;
+			default-state = "on";
+		};
+	};
+};
+
+&uart1 { /* MIO36/MIO37 */
+	status = "okay";
+};
+
+&qspi { /* MIO 0-5 - U143 */
+	status = "okay";
+	flash@0 { /* MT25QU512A */
+		compatible = "mt25qu512a", "jedec,spi-nor"; /* 64MB */
+		#address-cells = <1>;
+		#size-cells = <1>;
+		reg = <0>;
+		spi-tx-bus-width = <1>;
+		spi-rx-bus-width = <4>;
+		spi-max-frequency = <40000000>; /* 40MHz */
+		partition@0 {
+			label = "Image Selector";
+			reg = <0x0 0x80000>; /* 512KB */
+			read-only;
+			lock;
+		};
+		partition@80000 {
+			label = "Image Selector Golden";
+			reg = <0x80000 0x80000>; /* 512KB */
+			read-only;
+			lock;
+		};
+		partition@100000 {
+			label = "Persistent Register";
+			reg = <0x100000 0x20000>; /* 128KB */
+		};
+		partition@120000 {
+			label = "Persistent Register Backup";
+			reg = <0x120000 0x20000>; /* 128KB */
+		};
+		partition@140000 {
+			label = "Open_1";
+			reg = <0x140000 0xC0000>; /* 768KB */
+		};
+		partition@200000 {
+			label = "Image A (FSBL, PMU, ATF, U-Boot)";
+			reg = <0x200000 0xD00000>; /* 13MB */
+		};
+		partition@f00000 {
+			label = "ImgSel Image A Catch";
+			reg = <0xF00000 0x80000>; /* 512KB */
+			read-only;
+			lock;
+		};
+		partition@f80000 {
+			label = "Image B (FSBL, PMU, ATF, U-Boot)";
+			reg = <0xF80000 0xD00000>; /* 13MB */
+		};
+		partition@1c80000 {
+			label = "ImgSel Image B Catch";
+			reg = <0x1C80000 0x80000>; /* 512KB */
+			read-only;
+			lock;
+		};
+		partition@1d00000 {
+			label = "Open_2";
+			reg = <0x1D00000 0x100000>; /* 1MB */
+		};
+		partition@1e00000 {
+			label = "Recovery Image";
+			reg = <0x1E00000 0x200000>; /* 2MB */
+			read-only;
+			lock;
+		};
+		partition@2000000 {
+			label = "Recovery Image Backup";
+			reg = <0x2000000 0x200000>; /* 2MB */
+			read-only;
+			lock;
+		};
+		partition@2200000 {
+			label = "U-Boot storage variables";
+			reg = <0x2200000 0x20000>; /* 128KB */
+		};
+		partition@2220000 {
+			label = "U-Boot storage variables backup";
+			reg = <0x2220000 0x20000>; /* 128KB */
+		};
+		partition@2240000 {
+			label = "SHA256";
+			reg = <0x2240000 0x10000>; /* 256B but 64KB sector */
+			read-only;
+			lock;
+		};
+		partition@2250000 {
+			label = "User";
+			reg = <0x2250000 0x1db0000>; /* 29.5 MB */
+		};
+	};
+};
+
+&sdhci0 { /* MIO13-23 - 16GB emmc MTFC16GAPALBH-IT - U133A */
+	status = "okay";
+	non-removable;
+	disable-wp;
+	bus-width = <8>;
+	xlnx,mio-bank = <0>;
+};
+
+&spi1 { /* MIO6, 9-11 */
+	status = "okay";
+	label = "TPM";
+	num-cs = <1>;
+	tpm@0 { /* slm9670 - U144 */
+		compatible = "infineon,slb9670", "tcg,tpm_tis-spi";
+		reg = <0>;
+		spi-max-frequency = <18500000>;
+	};
+};
+
+&i2c1 {
+	status = "okay";
+	clock-frequency = <400000>;
+	scl-gpios = <&gpio 24 GPIO_ACTIVE_HIGH>;
+	sda-gpios = <&gpio 25 GPIO_ACTIVE_HIGH>;
+
+	eeprom: eeprom@50 { /* u46 - also at address 0x58 */
+		compatible = "st,24c64", "atmel,24c64"; /* st m24c64 */
+		reg = <0x50>;
+		/* WP pin EE_WP_EN connected to slg7x644092@68 */
+	};
+
+	eeprom_cc: eeprom@51 { /* required by spec - also at address 0x59 */
+		compatible = "st,24c64", "atmel,24c64"; /* st m24c64 */
+		reg = <0x51>;
+	};
+
+	/* da9062@30 - u170 - also at address 0x31 */
+	/* da9131@33 - u167 */
+	da9131: pmic@33 {
+		compatible = "dlg,da9131";
+		reg = <0x33>;
+		regulators {
+			da9131_buck1: buck1 {
+				regulator-name = "da9131_buck1";
+				regulator-boot-on;
+				regulator-always-on;
+			};
+			da9131_buck2: buck2 {
+				regulator-name = "da9131_buck2";
+				regulator-boot-on;
+				regulator-always-on;
+			};
+		};
+	};
+
+	/* da9130@32 - u166 */
+	da9130: pmic@32 {
+		compatible = "dlg,da9130";
+		reg = <0x32>;
+		regulators {
+			da9130_buck1: buck1 {
+				regulator-name = "da9130_buck1";
+				regulator-boot-on;
+				regulator-always-on;
+			};
+		};
+	};
+
+	/* slg7x644091@70 - u168 NOT accessible due to address conflict with stdp4320 */
+	/*
+	 * stdp4320 - u27 FW has below two issues to be fixed in next board revision.
+	 * Device acknowledging to addresses 0x5C, 0x5D, 0x70, 0x72, 0x76.
+	 * Address conflict with slg7x644091@70 making both the devices NOT accessible.
+	 * With the FW fix, stdp4320 should respond to address 0x73 only.
+	 */
+	/* slg7x644092@68 - u169 */
+	/* Also connected via JA1C as C23/C24 */
+};
+
+&gpio {
+	status = "okay";
+	gpio-line-names = "QSPI_CLK", "QSPI_DQ1", "QSPI_DQ2", "QSPI_DQ3", "QSPI_DQ0", /* 0 - 4 */
+			  "QSPI_CS_B", "SPI_CLK", "LED1", "LED2", "SPI_CS_B", /* 5 - 9 */
+			  "SPI_MISO", "SPI_MOSI", "FWUEN", "EMMC_DAT0", "EMMC_DAT1", /* 10 - 14 */
+			  "EMMC_DAT2", "EMMC_DAT3", "EMMC_DAT4", "EMMC_DAT5", "EMMC_DAT6", /* 15 - 19 */
+			  "EMMC_DAT7", "EMMC_CMD", "EMMC_CLK", "EMMC_RST", "I2C1_SCL", /* 20 - 24 */
+			  "I2C1_SDA", "", "", "", "", /* 25 - 29 */
+			  "", "", "", "", "", /* 30 - 34 */
+			  "", "", "", "", "", /* 35 - 39 */
+			  "", "", "", "", "", /* 40 - 44 */
+			  "", "", "", "", "", /* 45 - 49 */
+			  "", "", "", "", "", /* 50 - 54 */
+			  "", "", "", "", "", /* 55 - 59 */
+			  "", "", "", "", "", /* 60 - 64 */
+			  "", "", "", "", "", /* 65 - 69 */
+			  "", "", "", "", "", /* 70 - 74 */
+			  "", "", "", /* 75 - 77, MIO end and EMIO start */
+			  "", "", /* 78 - 79 */
+			  "", "", "", "", "", /* 80 - 84 */
+			  "", "", "", "", "", /* 85 - 89 */
+			  "", "", "", "", "", /* 90 - 94 */
+			  "", "", "", "", "", /* 95 - 99 */
+			  "", "", "", "", "", /* 100 - 104 */
+			  "", "", "", "", "", /* 105 - 109 */
+			  "", "", "", "", "", /* 110 - 114 */
+			  "", "", "", "", "", /* 115 - 119 */
+			  "", "", "", "", "", /* 120 - 124 */
+			  "", "", "", "", "", /* 125 - 129 */
+			  "", "", "", "", "", /* 130 - 134 */
+			  "", "", "", "", "", /* 135 - 139 */
+			  "", "", "", "", "", /* 140 - 144 */
+			  "", "", "", "", "", /* 145 - 149 */
+			  "", "", "", "", "", /* 150 - 154 */
+			  "", "", "", "", "", /* 155 - 159 */
+			  "", "", "", "", "", /* 160 - 164 */
+			  "", "", "", "", "", /* 165 - 169 */
+			  "", "", "", ""; /* 170 - 174 */
+};
diff --git a/arch/arm64/boot/dts/xilinx/zynqmp-smk-k26-revA.dts b/arch/arm64/boot/dts/xilinx/zynqmp-smk-k26-revA.dts
new file mode 100644
index 000000000000..c70966c1f344
--- /dev/null
+++ b/arch/arm64/boot/dts/xilinx/zynqmp-smk-k26-revA.dts
@@ -0,0 +1,21 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * dts file for Xilinx ZynqMP SMK-K26 rev1/B/A
+ *
+ * (C) Copyright 2020 - 2021, Xilinx, Inc.
+ *
+ * Michal Simek <michal.simek@xilinx.com>
+ */
+
+#include "zynqmp-sm-k26-revA.dts"
+
+/ {
+	model = "ZynqMP SMK-K26 Rev1/B/A";
+	compatible = "xlnx,zynqmp-smk-k26-rev1", "xlnx,zynqmp-smk-k26-revB",
+		     "xlnx,zynqmp-smk-k26-revA", "xlnx,zynqmp-smk-k26",
+		     "xlnx,zynqmp";
+};
+
+&sdhci0 {
+	status = "disabled";
+};
diff --git a/arch/arm64/boot/dts/xilinx/zynqmp-zc1232-revA.dts b/arch/arm64/boot/dts/xilinx/zynqmp-zc1232-revA.dts
index 2e05fa416955..f1598527e5ec 100644
--- a/arch/arm64/boot/dts/xilinx/zynqmp-zc1232-revA.dts
+++ b/arch/arm64/boot/dts/xilinx/zynqmp-zc1232-revA.dts
@@ -2,7 +2,7 @@
 /*
  * dts file for Xilinx ZynqMP ZC1232
  *
- * (C) Copyright 2017 - 2019, Xilinx, Inc.
+ * (C) Copyright 2017 - 2021, Xilinx, Inc.
  *
  * Michal Simek <michal.simek@xilinx.com>
  */
@@ -19,6 +19,7 @@
 	aliases {
 		serial0 = &uart0;
 		serial1 = &dcc;
+		spi0 = &qspi;
 	};
 
 	chosen {
@@ -36,6 +37,19 @@
 	status = "okay";
 };
 
+&qspi {
+	status = "okay";
+	flash@0 {
+		compatible = "m25p80", "jedec,spi-nor"; /* 32MB */
+		#address-cells = <1>;
+		#size-cells = <1>;
+		reg = <0x0>;
+		spi-tx-bus-width = <1>;
+		spi-rx-bus-width = <4>;
+		spi-max-frequency = <108000000>; /* Based on DC1 spec */
+	};
+};
+
 &sata {
 	status = "okay";
 	/* SATA OOB timing settings */
diff --git a/arch/arm64/boot/dts/xilinx/zynqmp-zc1254-revA.dts b/arch/arm64/boot/dts/xilinx/zynqmp-zc1254-revA.dts
index 3d0aaa02f184..04efa1683eaa 100644
--- a/arch/arm64/boot/dts/xilinx/zynqmp-zc1254-revA.dts
+++ b/arch/arm64/boot/dts/xilinx/zynqmp-zc1254-revA.dts
@@ -2,7 +2,7 @@
 /*
  * dts file for Xilinx ZynqMP ZC1254
  *
- * (C) Copyright 2015 - 2019, Xilinx, Inc.
+ * (C) Copyright 2015 - 2021, Xilinx, Inc.
  *
  * Michal Simek <michal.simek@xilinx.com>
  * Siva Durga Prasad Paladugu <sivadur@xilinx.com>
@@ -20,6 +20,7 @@
 	aliases {
 		serial0 = &uart0;
 		serial1 = &dcc;
+		spi0 = &qspi;
 	};
 
 	chosen {
@@ -37,6 +38,19 @@
 	status = "okay";
 };
 
+&qspi {
+	status = "okay";
+	flash@0 {
+		compatible = "m25p80", "jedec,spi-nor"; /* 32MB */
+		#address-cells = <1>;
+		#size-cells = <1>;
+		reg = <0x0>;
+		spi-tx-bus-width = <1>;
+		spi-rx-bus-width = <4>; /* FIXME also DUAL configuration possible */
+		spi-max-frequency = <108000000>; /* Based on DC1 spec */
+	};
+};
+
 &uart0 {
 	status = "okay";
 };
diff --git a/arch/arm64/boot/dts/xilinx/zynqmp-zc1275-revA.dts b/arch/arm64/boot/dts/xilinx/zynqmp-zc1275-revA.dts
index 66a90483b004..e971ba8c1418 100644
--- a/arch/arm64/boot/dts/xilinx/zynqmp-zc1275-revA.dts
+++ b/arch/arm64/boot/dts/xilinx/zynqmp-zc1275-revA.dts
@@ -2,7 +2,7 @@
 /*
  * dts file for Xilinx ZynqMP ZC1275
  *
- * (C) Copyright 2017 - 2019, Xilinx, Inc.
+ * (C) Copyright 2017 - 2021, Xilinx, Inc.
  *
  * Michal Simek <michal.simek@xilinx.com>
  * Siva Durga Prasad Paladugu <sivadur@xilinx.com>
@@ -20,6 +20,7 @@
 	aliases {
 		serial0 = &uart0;
 		serial1 = &dcc;
+		spi0 = &qspi;
 	};
 
 	chosen {
@@ -37,6 +38,21 @@
 	status = "okay";
 };
 
+&gpio {
+	status = "okay";
+};
+
+&qspi {
+	status = "okay";
+	flash@0 {
+		compatible = "m25p80", "jedec,spi-nor";
+		reg = <0x0>;
+		spi-tx-bus-width = <1>;
+		spi-rx-bus-width = <4>;
+		spi-max-frequency = <108000000>;
+	};
+};
+
 &uart0 {
 	status = "okay";
 };
diff --git a/arch/arm64/boot/dts/xilinx/zynqmp-zc1751-xm015-dc1.dts b/arch/arm64/boot/dts/xilinx/zynqmp-zc1751-xm015-dc1.dts
index 69f6e4610739..b05be2552826 100644
--- a/arch/arm64/boot/dts/xilinx/zynqmp-zc1751-xm015-dc1.dts
+++ b/arch/arm64/boot/dts/xilinx/zynqmp-zc1751-xm015-dc1.dts
@@ -2,7 +2,7 @@
 /*
  * dts file for Xilinx ZynqMP zc1751-xm015-dc1
  *
- * (C) Copyright 2015 - 2019, Xilinx, Inc.
+ * (C) Copyright 2015 - 2021, Xilinx, Inc.
  *
  * Michal Simek <michal.simek@xilinx.com>
  */
@@ -11,7 +11,9 @@
 
 #include "zynqmp.dtsi"
 #include "zynqmp-clk-ccf.dtsi"
+#include <dt-bindings/phy/phy.h>
 #include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/pinctrl/pinctrl-zynqmp.h>
 
 / {
 	model = "ZynqMP zc1751-xm015-dc1 RevA";
@@ -24,6 +26,8 @@
 		mmc1 = &sdhci1;
 		rtc0 = &rtc;
 		serial0 = &uart0;
+		spi0 = &qspi;
+		usb0 = &usb0;
 	};
 
 	chosen {
@@ -35,6 +39,24 @@
 		device_type = "memory";
 		reg = <0x0 0x0 0x0 0x80000000>, <0x8 0x00000000 0x0 0x80000000>;
 	};
+
+	clock_si5338_0: clk27 {	/* u55 SI5338-GM */
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <27000000>;
+	};
+
+	clock_si5338_2: clk26 {
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <26000000>;
+	};
+
+	clock_si5338_3: clk150 {
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <150000000>;
+	};
 };
 
 &fpd_dma_chan1 {
@@ -73,6 +95,8 @@
 	status = "okay";
 	phy-handle = <&phy0>;
 	phy-mode = "rgmii-id";
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_gem3_default>;
 	phy0: ethernet-phy@0 {
 		reg = <0>;
 	};
@@ -80,12 +104,19 @@
 
 &gpio {
 	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_gpio_default>;
 };
 
 
 &i2c1 {
 	status = "okay";
 	clock-frequency = <400000>;
+	pinctrl-names = "default", "gpio";
+	pinctrl-0 = <&pinctrl_i2c1_default>;
+	pinctrl-1 = <&pinctrl_i2c1_gpio>;
+	scl-gpios = <&gpio 36 GPIO_ACTIVE_HIGH>;
+	sda-gpios = <&gpio 37 GPIO_ACTIVE_HIGH>;
 
 	eeprom: eeprom@55 {
 		compatible = "atmel,24c64"; /* 24AA64 */
@@ -93,6 +124,236 @@
 	};
 };
 
+&pinctrl0 {
+	status = "okay";
+	pinctrl_i2c1_default: i2c1-default {
+		mux {
+			groups = "i2c1_9_grp";
+			function = "i2c1";
+		};
+
+		conf {
+			groups = "i2c1_9_grp";
+			bias-pull-up;
+			slew-rate = <SLEW_RATE_SLOW>;
+			power-source = <IO_STANDARD_LVCMOS18>;
+		};
+	};
+
+	pinctrl_i2c1_gpio: i2c1-gpio {
+		mux {
+			groups = "gpio0_36_grp", "gpio0_37_grp";
+			function = "gpio0";
+		};
+
+		conf {
+			groups = "gpio0_36_grp", "gpio0_37_grp";
+			slew-rate = <SLEW_RATE_SLOW>;
+			power-source = <IO_STANDARD_LVCMOS18>;
+		};
+	};
+
+	pinctrl_uart0_default: uart0-default {
+		mux {
+			groups = "uart0_8_grp";
+			function = "uart0";
+		};
+
+		conf {
+			groups = "uart0_8_grp";
+			slew-rate = <SLEW_RATE_SLOW>;
+			power-source = <IO_STANDARD_LVCMOS18>;
+		};
+
+		conf-rx {
+			pins = "MIO34";
+			bias-high-impedance;
+		};
+
+		conf-tx {
+			pins = "MIO35";
+			bias-disable;
+		};
+	};
+
+	pinctrl_usb0_default: usb0-default {
+		mux {
+			groups = "usb0_0_grp";
+			function = "usb0";
+		};
+
+		conf {
+			groups = "usb0_0_grp";
+			slew-rate = <SLEW_RATE_SLOW>;
+			power-source = <IO_STANDARD_LVCMOS18>;
+		};
+
+		conf-rx {
+			pins = "MIO52", "MIO53", "MIO55";
+			bias-high-impedance;
+		};
+
+		conf-tx {
+			pins = "MIO54", "MIO56", "MIO57", "MIO58", "MIO59",
+			       "MIO60", "MIO61", "MIO62", "MIO63";
+			bias-disable;
+		};
+	};
+
+	pinctrl_gem3_default: gem3-default {
+		mux {
+			function = "ethernet3";
+			groups = "ethernet3_0_grp";
+		};
+
+		conf {
+			groups = "ethernet3_0_grp";
+			slew-rate = <SLEW_RATE_SLOW>;
+			power-source = <IO_STANDARD_LVCMOS18>;
+		};
+
+		conf-rx {
+			pins = "MIO70", "MIO71", "MIO72", "MIO73", "MIO74",
+									"MIO75";
+			bias-high-impedance;
+			low-power-disable;
+		};
+
+		conf-tx {
+			pins = "MIO64", "MIO65", "MIO66", "MIO67", "MIO68",
+									"MIO69";
+			bias-disable;
+			low-power-enable;
+		};
+
+		mux-mdio {
+			function = "mdio3";
+			groups = "mdio3_0_grp";
+		};
+
+		conf-mdio {
+			groups = "mdio3_0_grp";
+			slew-rate = <SLEW_RATE_SLOW>;
+			power-source = <IO_STANDARD_LVCMOS18>;
+			bias-disable;
+		};
+	};
+
+	pinctrl_sdhci0_default: sdhci0-default {
+		mux {
+			groups = "sdio0_0_grp";
+			function = "sdio0";
+		};
+
+		conf {
+			groups = "sdio0_0_grp";
+			slew-rate = <SLEW_RATE_SLOW>;
+			power-source = <IO_STANDARD_LVCMOS18>;
+			bias-disable;
+		};
+
+		mux-cd {
+			groups = "sdio0_cd_0_grp";
+			function = "sdio0_cd";
+		};
+
+		conf-cd {
+			groups = "sdio0_cd_0_grp";
+			bias-high-impedance;
+			bias-pull-up;
+			slew-rate = <SLEW_RATE_SLOW>;
+			power-source = <IO_STANDARD_LVCMOS18>;
+		};
+
+		mux-wp {
+			groups = "sdio0_wp_0_grp";
+			function = "sdio0_wp";
+		};
+
+		conf-wp {
+			groups = "sdio0_wp_0_grp";
+			bias-high-impedance;
+			bias-pull-up;
+			slew-rate = <SLEW_RATE_SLOW>;
+			power-source = <IO_STANDARD_LVCMOS18>;
+		};
+	};
+
+	pinctrl_sdhci1_default: sdhci1-default {
+		mux {
+			groups = "sdio1_0_grp";
+			function = "sdio1";
+		};
+
+		conf {
+			groups = "sdio1_0_grp";
+			slew-rate = <SLEW_RATE_SLOW>;
+			power-source = <IO_STANDARD_LVCMOS18>;
+			bias-disable;
+		};
+
+		mux-cd {
+			groups = "sdio1_cd_0_grp";
+			function = "sdio1_cd";
+		};
+
+		conf-cd {
+			groups = "sdio1_cd_0_grp";
+			bias-high-impedance;
+			bias-pull-up;
+			slew-rate = <SLEW_RATE_SLOW>;
+			power-source = <IO_STANDARD_LVCMOS18>;
+		};
+
+		mux-wp {
+			groups = "sdio1_wp_0_grp";
+			function = "sdio1_wp";
+		};
+
+		conf-wp {
+			groups = "sdio1_wp_0_grp";
+			bias-high-impedance;
+			bias-pull-up;
+			slew-rate = <SLEW_RATE_SLOW>;
+			power-source = <IO_STANDARD_LVCMOS18>;
+		};
+	};
+
+	pinctrl_gpio_default: gpio-default {
+		mux {
+			function = "gpio0";
+			groups = "gpio0_38_grp";
+		};
+
+		conf {
+			groups = "gpio0_38_grp";
+			bias-disable;
+			slew-rate = <SLEW_RATE_SLOW>;
+			power-source = <IO_STANDARD_LVCMOS18>;
+		};
+	};
+};
+
+&psgtr {
+	status = "okay";
+	/* dp, usb3, sata */
+	clocks = <&clock_si5338_0>, <&clock_si5338_2>, <&clock_si5338_3>;
+	clock-names = "ref1", "ref2", "ref3";
+};
+
+&qspi {
+	status = "okay";
+	flash@0 {
+		compatible = "m25p80", "jedec,spi-nor"; /* Micron MT25QU512ABB8ESF */
+		#address-cells = <1>;
+		#size-cells = <1>;
+		reg = <0x0>;
+		spi-tx-bus-width = <1>;
+		spi-rx-bus-width = <4>;
+		spi-max-frequency = <108000000>; /* Based on DC1 spec */
+	};
+};
+
 &rtc {
 	status = "okay";
 };
@@ -108,25 +369,60 @@
 	ceva,p1-comwake-params = /bits/ 8 <0x06 0x19 0x08 0x0E>;
 	ceva,p1-burst-params = /bits/ 8 <0x13 0x08 0x4A 0x06>;
 	ceva,p1-retry-params = /bits/ 16 <0x96A4 0x3FFC>;
+	phy-names = "sata-phy";
+	phys = <&psgtr 3 PHY_TYPE_SATA 1 3>;
 };
 
 /* eMMC */
 &sdhci0 {
 	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_sdhci0_default>;
 	bus-width = <8>;
+	xlnx,mio-bank = <0>;
 };
 
 /* SD1 with level shifter */
 &sdhci1 {
 	status = "okay";
+	/*
+	 * This property should be removed for supporting UHS mode
+	 */
+	no-1-8-v;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_sdhci1_default>;
+	xlnx,mio-bank = <1>;
 };
 
 &uart0 {
 	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart0_default>;
 };
 
 /* ULPI SMSC USB3320 */
 &usb0 {
 	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usb0_default>;
+	phy-names = "usb3-phy";
+	phys = <&psgtr 2 PHY_TYPE_USB3 0 2>;
+};
+
+&dwc3_0 {
+	status = "okay";
 	dr_mode = "host";
+	snps,usb3_lpm_capable;
+	maximum-speed = "super-speed";
+};
+
+&zynqmp_dpdma {
+	status = "okay";
+};
+
+&zynqmp_dpsub {
+	status = "okay";
+	phy-names = "dp-phy0", "dp-phy1";
+	phys = <&psgtr 1 PHY_TYPE_DP 0 0>,
+	       <&psgtr 0 PHY_TYPE_DP 1 1>;
 };
diff --git a/arch/arm64/boot/dts/xilinx/zynqmp-zc1751-xm016-dc2.dts b/arch/arm64/boot/dts/xilinx/zynqmp-zc1751-xm016-dc2.dts
index 4a86efa32d68..938b76bd0527 100644
--- a/arch/arm64/boot/dts/xilinx/zynqmp-zc1751-xm016-dc2.dts
+++ b/arch/arm64/boot/dts/xilinx/zynqmp-zc1751-xm016-dc2.dts
@@ -2,7 +2,7 @@
 /*
  * dts file for Xilinx ZynqMP zc1751-xm016-dc2
  *
- * (C) Copyright 2015 - 2019, Xilinx, Inc.
+ * (C) Copyright 2015 - 2021, Xilinx, Inc.
  *
  * Michal Simek <michal.simek@xilinx.com>
  */
@@ -12,14 +12,13 @@
 #include "zynqmp.dtsi"
 #include "zynqmp-clk-ccf.dtsi"
 #include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/pinctrl/pinctrl-zynqmp.h>
 
 / {
 	model = "ZynqMP zc1751-xm016-dc2 RevA";
 	compatible = "xlnx,zynqmp-zc1751", "xlnx,zynqmp";
 
 	aliases {
-		can0 = &can0;
-		can1 = &can1;
 		ethernet0 = &gem2;
 		i2c0 = &i2c0;
 		rtc0 = &rtc;
@@ -27,6 +26,7 @@
 		serial1 = &uart1;
 		spi0 = &spi0;
 		spi1 = &spi1;
+		usb0 = &usb1;
 	};
 
 	chosen {
@@ -42,10 +42,14 @@
 
 &can0 {
 	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_can0_default>;
 };
 
 &can1 {
 	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_can1_default>;
 };
 
 &fpd_dma_chan1 {
@@ -84,6 +88,8 @@
 	status = "okay";
 	phy-handle = <&phy0>;
 	phy-mode = "rgmii-id";
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_gem2_default>;
 	phy0: ethernet-phy@5 {
 		reg = <5>;
 		ti,rx-internal-delay = <0x8>;
@@ -100,6 +106,11 @@
 &i2c0 {
 	status = "okay";
 	clock-frequency = <400000>;
+	pinctrl-names = "default", "gpio";
+	pinctrl-0 = <&pinctrl_i2c0_default>;
+	pinctrl-1 = <&pinctrl_i2c0_gpio>;
+	scl-gpios = <&gpio 6 GPIO_ACTIVE_HIGH>;
+	sda-gpios = <&gpio 7 GPIO_ACTIVE_HIGH>;
 
 	tca6416_u26: gpio@20 {
 		compatible = "ti,tca6416";
@@ -115,6 +126,311 @@
 	};
 };
 
+&nand0 {
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_nand0_default>;
+	arasan,has-mdma;
+
+	nand@0 {
+		reg = <0x0>;
+		#address-cells = <0x2>;
+		#size-cells = <0x1>;
+		nand-ecc-mode = "soft";
+		nand-ecc-algo = "bch";
+		nand-rb = <0>;
+		label = "main-storage-0";
+	};
+	nand@1 {
+		reg = <0x1>;
+		#address-cells = <0x2>;
+		#size-cells = <0x1>;
+		nand-ecc-mode = "soft";
+		nand-ecc-algo = "bch";
+		nand-rb = <0>;
+		label = "main-storage-1";
+	};
+};
+
+&pinctrl0 {
+	status = "okay";
+	pinctrl_can0_default: can0-default {
+		mux {
+			function = "can0";
+			groups = "can0_9_grp";
+		};
+
+		conf {
+			groups = "can0_9_grp";
+			slew-rate = <SLEW_RATE_SLOW>;
+			power-source = <IO_STANDARD_LVCMOS18>;
+		};
+
+		conf-rx {
+			pins = "MIO38";
+			bias-high-impedance;
+		};
+
+		conf-tx {
+			pins = "MIO39";
+			bias-disable;
+		};
+	};
+
+	pinctrl_can1_default: can1-default {
+		mux {
+			function = "can1";
+			groups = "can1_8_grp";
+		};
+
+		conf {
+			groups = "can1_8_grp";
+			slew-rate = <SLEW_RATE_SLOW>;
+			power-source = <IO_STANDARD_LVCMOS18>;
+		};
+
+		conf-rx {
+			pins = "MIO33";
+			bias-high-impedance;
+		};
+
+		conf-tx {
+			pins = "MIO32";
+			bias-disable;
+		};
+	};
+
+	pinctrl_i2c0_default: i2c0-default {
+		mux {
+			groups = "i2c0_1_grp";
+			function = "i2c0";
+		};
+
+		conf {
+			groups = "i2c0_1_grp";
+			bias-pull-up;
+			slew-rate = <SLEW_RATE_SLOW>;
+			power-source = <IO_STANDARD_LVCMOS18>;
+		};
+	};
+
+	pinctrl_i2c0_gpio: i2c0-gpio {
+		mux {
+			groups = "gpio0_6_grp", "gpio0_7_grp";
+			function = "gpio0";
+		};
+
+		conf {
+			groups = "gpio0_6_grp", "gpio0_7_grp";
+			slew-rate = <SLEW_RATE_SLOW>;
+			power-source = <IO_STANDARD_LVCMOS18>;
+		};
+	};
+
+	pinctrl_uart0_default: uart0-default {
+		mux {
+			groups = "uart0_10_grp";
+			function = "uart0";
+		};
+
+		conf {
+			groups = "uart0_10_grp";
+			slew-rate = <SLEW_RATE_SLOW>;
+			power-source = <IO_STANDARD_LVCMOS18>;
+		};
+
+		conf-rx {
+			pins = "MIO42";
+			bias-high-impedance;
+		};
+
+		conf-tx {
+			pins = "MIO43";
+			bias-disable;
+		};
+	};
+
+	pinctrl_uart1_default: uart1-default {
+		mux {
+			groups = "uart1_10_grp";
+			function = "uart1";
+		};
+
+		conf {
+			groups = "uart1_10_grp";
+			slew-rate = <SLEW_RATE_SLOW>;
+			power-source = <IO_STANDARD_LVCMOS18>;
+		};
+
+		conf-rx {
+			pins = "MIO41";
+			bias-high-impedance;
+		};
+
+		conf-tx {
+			pins = "MIO40";
+			bias-disable;
+		};
+	};
+
+	pinctrl_usb1_default: usb1-default {
+		mux {
+			groups = "usb1_0_grp";
+			function = "usb1";
+		};
+
+		conf {
+			groups = "usb1_0_grp";
+			slew-rate = <SLEW_RATE_SLOW>;
+			power-source = <IO_STANDARD_LVCMOS18>;
+		};
+
+		conf-rx {
+			pins = "MIO64", "MIO65", "MIO67";
+			bias-high-impedance;
+		};
+
+		conf-tx {
+			pins = "MIO66", "MIO68", "MIO69", "MIO70", "MIO71",
+			       "MIO72", "MIO73", "MIO74", "MIO75";
+			bias-disable;
+		};
+	};
+
+	pinctrl_gem2_default: gem2-default {
+		mux {
+			function = "ethernet2";
+			groups = "ethernet2_0_grp";
+		};
+
+		conf {
+			groups = "ethernet2_0_grp";
+			slew-rate = <SLEW_RATE_SLOW>;
+			power-source = <IO_STANDARD_LVCMOS18>;
+		};
+
+		conf-rx {
+			pins = "MIO58", "MIO59", "MIO60", "MIO61", "MIO62",
+									"MIO63";
+			bias-high-impedance;
+			low-power-disable;
+		};
+
+		conf-tx {
+			pins = "MIO52", "MIO53", "MIO54", "MIO55", "MIO56",
+									"MIO57";
+			bias-disable;
+			low-power-enable;
+		};
+
+		mux-mdio {
+			function = "mdio2";
+			groups = "mdio2_0_grp";
+		};
+
+		conf-mdio {
+			groups = "mdio2_0_grp";
+			slew-rate = <SLEW_RATE_SLOW>;
+			power-source = <IO_STANDARD_LVCMOS18>;
+			bias-disable;
+		};
+	};
+
+	pinctrl_nand0_default: nand0-default {
+		mux {
+			groups = "nand0_0_grp";
+			function = "nand0";
+		};
+
+		conf {
+			groups = "nand0_0_grp";
+			bias-pull-up;
+		};
+
+		mux-ce {
+			groups = "nand0_ce_0_grp";
+			function = "nand0_ce";
+		};
+
+		conf-ce {
+			groups = "nand0_ce_0_grp";
+			bias-pull-up;
+		};
+
+		mux-rb {
+			groups = "nand0_rb_0_grp";
+			function = "nand0_rb";
+		};
+
+		conf-rb {
+			groups = "nand0_rb_0_grp";
+			bias-pull-up;
+		};
+
+		mux-dqs {
+			groups = "nand0_dqs_0_grp";
+			function = "nand0_dqs";
+		};
+
+		conf-dqs {
+			groups = "nand0_dqs_0_grp";
+			bias-pull-up;
+		};
+	};
+
+	pinctrl_spi0_default: spi0-default {
+		mux {
+			groups = "spi0_0_grp";
+			function = "spi0";
+		};
+
+		conf {
+			groups = "spi0_0_grp";
+			bias-disable;
+			slew-rate = <SLEW_RATE_SLOW>;
+			power-source = <IO_STANDARD_LVCMOS18>;
+		};
+
+		mux-cs {
+			groups = "spi0_ss_0_grp", "spi0_ss_1_grp",
+							"spi0_ss_2_grp";
+			function = "spi0_ss";
+		};
+
+		conf-cs {
+			groups = "spi0_ss_0_grp", "spi0_ss_1_grp",
+							"spi0_ss_2_grp";
+			bias-disable;
+		};
+	};
+
+	pinctrl_spi1_default: spi1-default {
+		mux {
+			groups = "spi1_3_grp";
+			function = "spi1";
+		};
+
+		conf {
+			groups = "spi1_3_grp";
+			bias-disable;
+			slew-rate = <SLEW_RATE_SLOW>;
+			power-source = <IO_STANDARD_LVCMOS18>;
+		};
+
+		mux-cs {
+			groups = "spi1_ss_9_grp", "spi1_ss_10_grp",
+							"spi1_ss_11_grp";
+			function = "spi1_ss";
+		};
+
+		conf-cs {
+			groups = "spi1_ss_9_grp", "spi1_ss_10_grp",
+							"spi1_ss_11_grp";
+			bias-disable;
+		};
+	};
+};
+
 &rtc {
 	status = "okay";
 };
@@ -122,6 +438,8 @@
 &spi0 {
 	status = "okay";
 	num-cs = <1>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_spi0_default>;
 
 	spi0_flash0: flash@0 {
 		#address-cells = <1>;
@@ -131,7 +449,7 @@
 		reg = <0>;
 
 		partition@0 {
-			label = "data";
+			label = "spi0-data";
 			reg = <0x0 0x100000>;
 		};
 	};
@@ -140,6 +458,8 @@
 &spi1 {
 	status = "okay";
 	num-cs = <1>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_spi1_default>;
 
 	spi1_flash0: flash@0 {
 		#address-cells = <1>;
@@ -149,7 +469,7 @@
 		reg = <0>;
 
 		partition@0 {
-			label = "data";
+			label = "spi1-data";
 			reg = <0x0 0x84000>;
 		};
 	};
@@ -158,13 +478,25 @@
 /* ULPI SMSC USB3320 */
 &usb1 {
 	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usb1_default>;
+};
+
+&dwc3_1 {
+	status = "okay";
 	dr_mode = "host";
+	snps,usb3_lpm_capable;
+	maximum-speed = "super-speed";
 };
 
 &uart0 {
 	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart0_default>;
 };
 
 &uart1 {
 	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart1_default>;
 };
diff --git a/arch/arm64/boot/dts/xilinx/zynqmp-zc1751-xm017-dc3.dts b/arch/arm64/boot/dts/xilinx/zynqmp-zc1751-xm017-dc3.dts
index 4ea6ef5a7f2b..381cc682cef9 100644
--- a/arch/arm64/boot/dts/xilinx/zynqmp-zc1751-xm017-dc3.dts
+++ b/arch/arm64/boot/dts/xilinx/zynqmp-zc1751-xm017-dc3.dts
@@ -2,7 +2,7 @@
 /*
  * dts file for Xilinx ZynqMP zc1751-xm017-dc3
  *
- * (C) Copyright 2016 - 2019, Xilinx, Inc.
+ * (C) Copyright 2016 - 2021, Xilinx, Inc.
  *
  * Michal Simek <michal.simek@xilinx.com>
  */
@@ -11,6 +11,7 @@
 
 #include "zynqmp.dtsi"
 #include "zynqmp-clk-ccf.dtsi"
+#include <dt-bindings/phy/phy.h>
 
 / {
 	model = "ZynqMP zc1751-xm017-dc3 RevA";
@@ -24,6 +25,8 @@
 		rtc0 = &rtc;
 		serial0 = &uart0;
 		serial1 = &uart1;
+		usb0 = &usb0;
+		usb1 = &usb1;
 	};
 
 	chosen {
@@ -35,6 +38,18 @@
 		device_type = "memory";
 		reg = <0x0 0x0 0x0 0x80000000>, <0x8 0x00000000 0x0 0x80000000>;
 	};
+
+	clock_si5338_2: clk26 {
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <26000000>;
+	};
+
+	clock_si5338_3: clk125 {
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <125000000>;
+	};
 };
 
 &fpd_dma_chan1 {
@@ -107,6 +122,20 @@
 	clock-frequency = <400000>;
 };
 
+/* MT29F64G08AECDBJ4-6 */
+&nand0 {
+	status = "okay";
+	arasan,has-mdma;
+	num-cs = <2>;
+};
+
+&psgtr {
+	status = "okay";
+	/* usb3, sata */
+	clocks = <&clock_si5338_2>, <&clock_si5338_3>;
+	clock-names = "ref2", "ref3";
+};
+
 &rtc {
 	status = "okay";
 };
@@ -122,6 +151,8 @@
 	ceva,p1-comwake-params = /bits/ 8 <0x06 0x19 0x08 0x0E>;
 	ceva,p1-burst-params = /bits/ 8 <0x13 0x08 0x4A 0x06>;
 	ceva,p1-retry-params = /bits/ 16 <0x96A4 0x3FFC>;
+	phy-names = "sata-phy";
+	phys = <&psgtr 2 PHY_TYPE_SATA 0 3>;
 };
 
 &sdhci1 { /* emmc with some settings */
@@ -140,11 +171,27 @@
 
 &usb0 {
 	status = "okay";
+	phy-names = "usb3-phy";
+	phys = <&psgtr 0 PHY_TYPE_USB3 0 2>;
+};
+
+&dwc3_0 {
+	status = "okay";
 	dr_mode = "host";
+	snps,usb3_lpm_capable;
+	maximum-speed = "super-speed";
 };
 
 /* ULPI SMSC USB3320 */
 &usb1 {
 	status = "okay";
+	phy-names = "usb3-phy";
+	phys = <&psgtr 3 PHY_TYPE_USB3 1 2>;
+};
+
+&dwc3_1 {
+	status = "okay";
 	dr_mode = "host";
+	snps,usb3_lpm_capable;
+	maximum-speed = "super-speed";
 };
diff --git a/arch/arm64/boot/dts/xilinx/zynqmp-zc1751-xm018-dc4.dts b/arch/arm64/boot/dts/xilinx/zynqmp-zc1751-xm018-dc4.dts
index 2366cd9f091a..05a2b79738af 100644
--- a/arch/arm64/boot/dts/xilinx/zynqmp-zc1751-xm018-dc4.dts
+++ b/arch/arm64/boot/dts/xilinx/zynqmp-zc1751-xm018-dc4.dts
@@ -2,7 +2,7 @@
 /*
  * dts file for Xilinx ZynqMP zc1751-xm018-dc4
  *
- * (C) Copyright 2015 - 2019, Xilinx, Inc.
+ * (C) Copyright 2015 - 2021, Xilinx, Inc.
  *
  * Michal Simek <michal.simek@xilinx.com>
  */
@@ -26,6 +26,7 @@
 		rtc0 = &rtc;
 		serial0 = &uart0;
 		serial1 = &uart1;
+		spi0 = &qspi;
 	};
 
 	chosen {
@@ -161,6 +162,19 @@
 	status = "okay";
 };
 
+&qspi {
+	status = "okay";
+	flash@0 {
+		compatible = "m25p80", "jedec,spi-nor"; /* 32MB */
+		#address-cells = <1>;
+		#size-cells = <1>;
+		reg = <0x0>;
+		spi-tx-bus-width = <1>;
+		spi-rx-bus-width = <4>; /* also DUAL configuration possible */
+		spi-max-frequency = <108000000>; /* Based on DC1 spec */
+	};
+};
+
 &rtc {
 	status = "okay";
 };
@@ -176,3 +190,11 @@
 &watchdog0 {
 	status = "okay";
 };
+
+&zynqmp_dpdma {
+	status = "okay";
+};
+
+&zynqmp_dpsub {
+	status = "okay";
+};
diff --git a/arch/arm64/boot/dts/xilinx/zynqmp-zc1751-xm019-dc5.dts b/arch/arm64/boot/dts/xilinx/zynqmp-zc1751-xm019-dc5.dts
index 41934e3525c6..ae2d03d98322 100644
--- a/arch/arm64/boot/dts/xilinx/zynqmp-zc1751-xm019-dc5.dts
+++ b/arch/arm64/boot/dts/xilinx/zynqmp-zc1751-xm019-dc5.dts
@@ -2,7 +2,7 @@
 /*
  * dts file for Xilinx ZynqMP zc1751-xm019-dc5
  *
- * (C) Copyright 2015 - 2019, Xilinx, Inc.
+ * (C) Copyright 2015 - 2021, Xilinx, Inc.
  *
  * Siva Durga Prasad <siva.durga.paladugu@xilinx.com>
  * Michal Simek <michal.simek@xilinx.com>
@@ -13,6 +13,7 @@
 #include "zynqmp.dtsi"
 #include "zynqmp-clk-ccf.dtsi"
 #include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/pinctrl/pinctrl-zynqmp.h>
 
 / {
 	model = "ZynqMP zc1751-xm019-dc5 RevA";
@@ -74,6 +75,8 @@
 	status = "okay";
 	phy-handle = <&phy0>;
 	phy-mode = "rgmii-id";
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_gem1_default>;
 	phy0: ethernet-phy@0 {
 		reg = <0>;
 	};
@@ -85,41 +88,366 @@
 
 &i2c0 {
 	status = "okay";
+	pinctrl-names = "default", "gpio";
+	pinctrl-0 = <&pinctrl_i2c0_default>;
+	pinctrl-1 = <&pinctrl_i2c0_gpio>;
+	scl-gpios = <&gpio 74 GPIO_ACTIVE_HIGH>;
+	sda-gpios = <&gpio 75 GPIO_ACTIVE_HIGH>;
 };
 
 &i2c1 {
 	status = "okay";
+	pinctrl-names = "default", "gpio";
+	pinctrl-0 = <&pinctrl_i2c1_default>;
+	pinctrl-1 = <&pinctrl_i2c1_gpio>;
+	scl-gpios = <&gpio 76 GPIO_ACTIVE_HIGH>;
+	sda-gpios = <&gpio 77 GPIO_ACTIVE_HIGH>;
+
+};
+
+&pinctrl0 {
+	status = "okay";
+	pinctrl_i2c0_default: i2c0-default {
+		mux {
+			groups = "i2c0_18_grp";
+			function = "i2c0";
+		};
+
+		conf {
+			groups = "i2c0_18_grp";
+			bias-pull-up;
+			slew-rate = <SLEW_RATE_SLOW>;
+			power-source = <IO_STANDARD_LVCMOS18>;
+		};
+	};
+
+	pinctrl_i2c0_gpio: i2c0-gpio {
+		mux {
+			groups = "gpio0_74_grp", "gpio0_75_grp";
+			function = "gpio0";
+		};
+
+		conf {
+			groups = "gpio0_74_grp", "gpio0_75_grp";
+			slew-rate = <SLEW_RATE_SLOW>;
+			power-source = <IO_STANDARD_LVCMOS18>;
+		};
+	};
+
+	pinctrl_i2c1_default: i2c1-default {
+		mux {
+			groups = "i2c1_19_grp";
+			function = "i2c1";
+		};
+
+		conf {
+			groups = "i2c1_19_grp";
+			bias-pull-up;
+			slew-rate = <SLEW_RATE_SLOW>;
+			power-source = <IO_STANDARD_LVCMOS18>;
+		};
+	};
+
+	pinctrl_i2c1_gpio: i2c1-gpio {
+		mux {
+			groups = "gpio0_76_grp", "gpio0_77_grp";
+			function = "gpio0";
+		};
+
+		conf {
+			groups = "gpio0_76_grp", "gpio0_77_grp";
+			slew-rate = <SLEW_RATE_SLOW>;
+			power-source = <IO_STANDARD_LVCMOS18>;
+		};
+	};
+
+	pinctrl_uart0_default: uart0-default {
+		mux {
+			groups = "uart0_17_grp";
+			function = "uart0";
+		};
+
+		conf {
+			groups = "uart0_17_grp";
+			slew-rate = <SLEW_RATE_SLOW>;
+			power-source = <IO_STANDARD_LVCMOS18>;
+		};
+
+		conf-rx {
+			pins = "MIO70";
+			bias-high-impedance;
+		};
+
+		conf-tx {
+			pins = "MIO71";
+			bias-disable;
+		};
+	};
+
+	pinctrl_uart1_default: uart1-default {
+		mux {
+			groups = "uart1_18_grp";
+			function = "uart1";
+		};
+
+		conf {
+			groups = "uart1_18_grp";
+			slew-rate = <SLEW_RATE_SLOW>;
+			power-source = <IO_STANDARD_LVCMOS18>;
+		};
+
+		conf-rx {
+			pins = "MIO73";
+			bias-high-impedance;
+		};
+
+		conf-tx {
+			pins = "MIO72";
+			bias-disable;
+		};
+	};
+
+	pinctrl_gem1_default: gem1-default {
+		mux {
+			function = "ethernet1";
+			groups = "ethernet1_0_grp";
+		};
+
+		conf {
+			groups = "ethernet1_0_grp";
+			slew-rate = <SLEW_RATE_SLOW>;
+			power-source = <IO_STANDARD_LVCMOS18>;
+		};
+
+		conf-rx {
+			pins = "MIO44", "MIO45", "MIO46", "MIO47", "MIO48",
+									"MIO49";
+			bias-high-impedance;
+			low-power-disable;
+		};
+
+		conf-tx {
+			pins = "MIO38", "MIO39", "MIO40", "MIO41", "MIO42",
+									"MIO43";
+			bias-disable;
+			low-power-enable;
+		};
+
+		mux-mdio {
+			function = "mdio1";
+			groups = "mdio1_0_grp";
+		};
+
+		conf-mdio {
+			groups = "mdio1_0_grp";
+			slew-rate = <SLEW_RATE_SLOW>;
+			power-source = <IO_STANDARD_LVCMOS18>;
+			bias-disable;
+		};
+	};
+
+	pinctrl_sdhci0_default: sdhci0-default {
+		mux {
+			groups = "sdio0_0_grp";
+			function = "sdio0";
+		};
+
+		conf {
+			groups = "sdio0_0_grp";
+			slew-rate = <SLEW_RATE_SLOW>;
+			power-source = <IO_STANDARD_LVCMOS18>;
+			bias-disable;
+		};
+
+		mux-cd {
+			groups = "sdio0_cd_0_grp";
+			function = "sdio0_cd";
+		};
+
+		conf-cd {
+			groups = "sdio0_cd_0_grp";
+			bias-high-impedance;
+			bias-pull-up;
+			slew-rate = <SLEW_RATE_SLOW>;
+			power-source = <IO_STANDARD_LVCMOS18>;
+		};
+
+		mux-wp {
+			groups = "sdio0_wp_0_grp";
+			function = "sdio0_wp";
+		};
+
+		conf-wp {
+			groups = "sdio0_wp_0_grp";
+			bias-high-impedance;
+			bias-pull-up;
+			slew-rate = <SLEW_RATE_SLOW>;
+			power-source = <IO_STANDARD_LVCMOS18>;
+		};
+	};
+
+	pinctrl_watchdog0_default: watchdog0-default {
+		mux-clk {
+			groups = "swdt0_clk_1_grp";
+			function = "swdt0_clk";
+		};
+
+		conf-clk {
+			groups = "swdt0_clk_1_grp";
+			bias-pull-up;
+		};
+
+		mux-rst {
+			groups = "swdt0_rst_1_grp";
+			function = "swdt0_rst";
+		};
+
+		conf-rst {
+			groups = "swdt0_rst_1_grp";
+			bias-disable;
+			slew-rate = <SLEW_RATE_SLOW>;
+		};
+	};
+
+	pinctrl_ttc0_default: ttc0-default {
+		mux-clk {
+			groups = "ttc0_clk_0_grp";
+			function = "ttc0_clk";
+		};
+
+		conf-clk {
+			groups = "ttc0_clk_0_grp";
+			bias-pull-up;
+		};
+
+		mux-wav {
+			groups = "ttc0_wav_0_grp";
+			function = "ttc0_wav";
+		};
+
+		conf-wav {
+			groups = "ttc0_wav_0_grp";
+			bias-disable;
+			slew-rate = <SLEW_RATE_SLOW>;
+		};
+	};
+
+	pinctrl_ttc1_default: ttc1-default {
+		mux-clk {
+			groups = "ttc1_clk_0_grp";
+			function = "ttc1_clk";
+		};
+
+		conf-clk {
+			groups = "ttc1_clk_0_grp";
+			bias-pull-up;
+		};
+
+		mux-wav {
+			groups = "ttc1_wav_0_grp";
+			function = "ttc1_wav";
+		};
+
+		conf-wav {
+			groups = "ttc1_wav_0_grp";
+			bias-disable;
+			slew-rate = <SLEW_RATE_SLOW>;
+		};
+	};
+
+	pinctrl_ttc2_default: ttc2-default {
+		mux-clk {
+			groups = "ttc2_clk_0_grp";
+			function = "ttc2_clk";
+		};
+
+		conf-clk {
+			groups = "ttc2_clk_0_grp";
+			bias-pull-up;
+		};
+
+		mux-wav {
+			groups = "ttc2_wav_0_grp";
+			function = "ttc2_wav";
+		};
+
+		conf-wav {
+			groups = "ttc2_wav_0_grp";
+			bias-disable;
+			slew-rate = <SLEW_RATE_SLOW>;
+		};
+	};
+
+	pinctrl_ttc3_default: ttc3-default {
+		mux-clk {
+			groups = "ttc3_clk_0_grp";
+			function = "ttc3_clk";
+		};
+
+		conf-clk {
+			groups = "ttc3_clk_0_grp";
+			bias-pull-up;
+		};
+
+		mux-wav {
+			groups = "ttc3_wav_0_grp";
+			function = "ttc3_wav";
+		};
+
+		conf-wav {
+			groups = "ttc3_wav_0_grp";
+			bias-disable;
+			slew-rate = <SLEW_RATE_SLOW>;
+		};
+	};
 };
 
 &sdhci0 {
 	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_sdhci0_default>;
 	no-1-8-v;
+	xlnx,mio-bank = <0>;
 };
 
 &ttc0 {
 	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_ttc0_default>;
 };
 
 &ttc1 {
 	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_ttc1_default>;
 };
 
 &ttc2 {
 	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_ttc2_default>;
 };
 
 &ttc3 {
 	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_ttc3_default>;
 };
 
 &uart0 {
 	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart0_default>;
 };
 
 &uart1 {
 	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart1_default>;
 };
 
 &watchdog0 {
 	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_watchdog0_default>;
 };
diff --git a/arch/arm64/boot/dts/xilinx/zynqmp-zcu100-revC.dts b/arch/arm64/boot/dts/xilinx/zynqmp-zcu100-revC.dts
index a53598c3624b..f6aad4159ccd 100644
--- a/arch/arm64/boot/dts/xilinx/zynqmp-zcu100-revC.dts
+++ b/arch/arm64/boot/dts/xilinx/zynqmp-zcu100-revC.dts
@@ -2,7 +2,7 @@
 /*
  * dts file for Xilinx ZynqMP ZCU100 revC
  *
- * (C) Copyright 2016 - 2019, Xilinx, Inc.
+ * (C) Copyright 2016 - 2021, Xilinx, Inc.
  *
  * Michal Simek <michal.simek@xilinx.com>
  * Nathalie Chan King Choy
@@ -15,6 +15,7 @@
 #include <dt-bindings/input/input.h>
 #include <dt-bindings/interrupt-controller/irq.h>
 #include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/pinctrl/pinctrl-zynqmp.h>
 #include <dt-bindings/phy/phy.h>
 
 / {
@@ -29,6 +30,8 @@
 		serial2 = &dcc;
 		spi0 = &spi0;
 		spi1 = &spi1;
+		usb0 = &usb0;
+		usb1 = &usb1;
 		mmc0 = &sdhci0;
 		mmc1 = &sdhci1;
 	};
@@ -110,13 +113,13 @@
 		io-channels = <&u35 0>, <&u35 1>, <&u35 2>, <&u35 3>;
 	};
 
-	si5335a_0: clk26 {
+	si5335_0: si5335_0 { /* clk0_usb - u23 */
 		compatible = "fixed-clock";
 		#clock-cells = <0>;
 		clock-frequency = <26000000>;
 	};
 
-	si5335a_1: clk27 {
+	si5335_1: si5335_1 { /* clk1_dp - u23 */
 		compatible = "fixed-clock";
 		#clock-cells = <0>;
 		clock-frequency = <27000000>;
@@ -160,6 +163,11 @@
 
 &i2c1 {
 	status = "okay";
+	pinctrl-names = "default", "gpio";
+	pinctrl-0 = <&pinctrl_i2c1_default>;
+	pinctrl-1 = <&pinctrl_i2c1_gpio>;
+	scl-gpios = <&gpio 4 GPIO_ACTIVE_HIGH>;
+	sda-gpios = <&gpio 5 GPIO_ACTIVE_HIGH>;
 	clock-frequency = <100000>;
 	i2c-mux@75 { /* u11 */
 		compatible = "nxp,pca9548";
@@ -237,10 +245,225 @@
 	};
 };
 
+&pinctrl0 {
+	status = "okay";
+	pinctrl_i2c1_default: i2c1-default {
+		mux {
+			groups = "i2c1_1_grp";
+			function = "i2c1";
+		};
+
+		conf {
+			groups = "i2c1_1_grp";
+			bias-pull-up;
+			slew-rate = <SLEW_RATE_SLOW>;
+			power-source = <IO_STANDARD_LVCMOS18>;
+		};
+	};
+
+	pinctrl_i2c1_gpio: i2c1-gpio {
+		mux {
+			groups = "gpio0_4_grp", "gpio0_5_grp";
+			function = "gpio0";
+		};
+
+		conf {
+			groups = "gpio0_4_grp", "gpio0_5_grp";
+			slew-rate = <SLEW_RATE_SLOW>;
+			power-source = <IO_STANDARD_LVCMOS18>;
+		};
+	};
+
+	pinctrl_sdhci0_default: sdhci0-default {
+		mux {
+			groups = "sdio0_3_grp";
+			function = "sdio0";
+		};
+
+		conf {
+			groups = "sdio0_3_grp";
+			slew-rate = <SLEW_RATE_SLOW>;
+			power-source = <IO_STANDARD_LVCMOS18>;
+			bias-disable;
+		};
+
+		mux-cd {
+			groups = "sdio0_cd_0_grp";
+			function = "sdio0_cd";
+		};
+
+		conf-cd {
+			groups = "sdio0_cd_0_grp";
+			bias-high-impedance;
+			bias-pull-up;
+			slew-rate = <SLEW_RATE_SLOW>;
+			power-source = <IO_STANDARD_LVCMOS18>;
+		};
+	};
+
+	pinctrl_sdhci1_default: sdhci1-default {
+		mux {
+			groups = "sdio1_2_grp";
+			function = "sdio1";
+		};
+
+		conf {
+			groups = "sdio1_2_grp";
+			slew-rate = <SLEW_RATE_SLOW>;
+			power-source = <IO_STANDARD_LVCMOS18>;
+			bias-disable;
+		};
+	};
+
+	pinctrl_spi0_default: spi0-default {
+		mux {
+			groups = "spi0_3_grp";
+			function = "spi0";
+		};
+
+		conf {
+			groups = "spi0_3_grp";
+			bias-disable;
+			slew-rate = <SLEW_RATE_SLOW>;
+			power-source = <IO_STANDARD_LVCMOS18>;
+		};
+
+		mux-cs {
+			groups = "spi0_ss_9_grp";
+			function = "spi0_ss";
+		};
+
+		conf-cs {
+			groups = "spi0_ss_9_grp";
+			bias-disable;
+		};
+
+	};
+
+	pinctrl_spi1_default: spi1-default {
+		mux {
+			groups = "spi1_0_grp";
+			function = "spi1";
+		};
+
+		conf {
+			groups = "spi1_0_grp";
+			bias-disable;
+			slew-rate = <SLEW_RATE_SLOW>;
+			power-source = <IO_STANDARD_LVCMOS18>;
+		};
+
+		mux-cs {
+			groups = "spi1_ss_0_grp";
+			function = "spi1_ss";
+		};
+
+		conf-cs {
+			groups = "spi1_ss_0_grp";
+			bias-disable;
+		};
+
+	};
+
+	pinctrl_uart0_default: uart0-default {
+		mux {
+			groups = "uart0_0_grp";
+			function = "uart0";
+		};
+
+		conf {
+			groups = "uart0_0_grp";
+			slew-rate = <SLEW_RATE_SLOW>;
+			power-source = <IO_STANDARD_LVCMOS18>;
+		};
+
+		conf-rx {
+			pins = "MIO3";
+			bias-high-impedance;
+		};
+
+		conf-tx {
+			pins = "MIO2";
+			bias-disable;
+		};
+	};
+
+	pinctrl_uart1_default: uart1-default {
+		mux {
+			groups = "uart1_0_grp";
+			function = "uart1";
+		};
+
+		conf {
+			groups = "uart1_0_grp";
+			slew-rate = <SLEW_RATE_SLOW>;
+			power-source = <IO_STANDARD_LVCMOS18>;
+		};
+
+		conf-rx {
+			pins = "MIO1";
+			bias-high-impedance;
+		};
+
+		conf-tx {
+			pins = "MIO0";
+			bias-disable;
+		};
+	};
+
+	pinctrl_usb0_default: usb0-default {
+		mux {
+			groups = "usb0_0_grp";
+			function = "usb0";
+		};
+
+		conf {
+			groups = "usb0_0_grp";
+			slew-rate = <SLEW_RATE_SLOW>;
+			power-source = <IO_STANDARD_LVCMOS18>;
+		};
+
+		conf-rx {
+			pins = "MIO52", "MIO53", "MIO55";
+			bias-high-impedance;
+		};
+
+		conf-tx {
+			pins = "MIO54", "MIO56", "MIO57", "MIO58", "MIO59",
+			       "MIO60", "MIO61", "MIO62", "MIO63";
+			bias-disable;
+		};
+	};
+
+	pinctrl_usb1_default: usb1-default {
+		mux {
+			groups = "usb1_0_grp";
+			function = "usb1";
+		};
+
+		conf {
+			groups = "usb1_0_grp";
+			slew-rate = <SLEW_RATE_SLOW>;
+			power-source = <IO_STANDARD_LVCMOS18>;
+		};
+
+		conf-rx {
+			pins = "MIO64", "MIO65", "MIO67";
+			bias-high-impedance;
+		};
+
+		conf-tx {
+			pins = "MIO66", "MIO68", "MIO69", "MIO70", "MIO71",
+			       "MIO72", "MIO73", "MIO74", "MIO75";
+			bias-disable;
+		};
+	};
+};
+
 &psgtr {
 	status = "okay";
-	/* usb3, dps */
-	clocks = <&si5335a_0>, <&si5335a_1>;
+	/* usb3, dp */
+	clocks = <&si5335_0>, <&si5335_1>;
 	clock-names = "ref0", "ref1";
 };
 
@@ -253,12 +476,16 @@
 	status = "okay";
 	no-1-8-v;
 	disable-wp;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_sdhci0_default>;
 	xlnx,mio-bank = <0>;
 };
 
 &sdhci1 {
 	status = "okay";
 	bus-width = <0x4>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_sdhci1_default>;
 	xlnx,mio-bank = <0>;
 	non-removable;
 	disable-wp;
@@ -279,16 +506,22 @@
 	status = "okay";
 	label = "LS-SPI0";
 	num-cs = <1>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_spi0_default>;
 };
 
 &spi1 { /* High Speed connector */
 	status = "okay";
 	label = "HS-SPI1";
 	num-cs = <1>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_spi1_default>;
 };
 
 &uart0 {
 	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart0_default>;
 	bluetooth {
 		compatible = "ti,wl1831-st";
 		enable-gpios = <&gpio 8 GPIO_ACTIVE_HIGH>;
@@ -297,19 +530,38 @@
 
 &uart1 {
 	status = "okay";
-
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart1_default>;
 };
 
 /* ULPI SMSC USB3320 */
 &usb0 {
 	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usb0_default>;
+	phy-names = "usb3-phy";
+	phys = <&psgtr 2 PHY_TYPE_USB3 0 0>;
+};
+
+&dwc3_0 {
+	status = "okay";
 	dr_mode = "peripheral";
+	maximum-speed = "super-speed";
 };
 
 /* ULPI SMSC USB3320 */
 &usb1 {
 	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usb1_default>;
+	phy-names = "usb3-phy";
+	phys = <&psgtr 3 PHY_TYPE_USB3 1 0>;
+};
+
+&dwc3_1 {
+	status = "okay";
 	dr_mode = "host";
+	maximum-speed = "super-speed";
 };
 
 &watchdog0 {
diff --git a/arch/arm64/boot/dts/xilinx/zynqmp-zcu102-rev1.1.dts b/arch/arm64/boot/dts/xilinx/zynqmp-zcu102-rev1.1.dts
new file mode 100644
index 000000000000..b6798394fcf4
--- /dev/null
+++ b/arch/arm64/boot/dts/xilinx/zynqmp-zcu102-rev1.1.dts
@@ -0,0 +1,15 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * dts file for Xilinx ZynqMP ZCU102 Rev1.1
+ *
+ * (C) Copyright 2016 - 2020, Xilinx, Inc.
+ *
+ * Michal Simek <michal.simek@xilinx.com>
+ */
+
+#include "zynqmp-zcu102-rev1.0.dts"
+
+/ {
+	model = "ZynqMP ZCU102 Rev1.1";
+	compatible = "xlnx,zynqmp-zcu102-rev1.1", "xlnx,zynqmp-zcu102", "xlnx,zynqmp";
+};
diff --git a/arch/arm64/boot/dts/xilinx/zynqmp-zcu102-revA.dts b/arch/arm64/boot/dts/xilinx/zynqmp-zcu102-revA.dts
index eca6c2de84a7..7b9a88b125d1 100644
--- a/arch/arm64/boot/dts/xilinx/zynqmp-zcu102-revA.dts
+++ b/arch/arm64/boot/dts/xilinx/zynqmp-zcu102-revA.dts
@@ -2,7 +2,7 @@
 /*
  * dts file for Xilinx ZynqMP ZCU102 RevA
  *
- * (C) Copyright 2015 - 2019, Xilinx, Inc.
+ * (C) Copyright 2015 - 2021, Xilinx, Inc.
  *
  * Michal Simek <michal.simek@xilinx.com>
  */
@@ -13,6 +13,7 @@
 #include "zynqmp-clk-ccf.dtsi"
 #include <dt-bindings/input/input.h>
 #include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/pinctrl/pinctrl-zynqmp.h>
 #include <dt-bindings/phy/phy.h>
 
 / {
@@ -24,10 +25,13 @@
 		i2c0 = &i2c0;
 		i2c1 = &i2c1;
 		mmc0 = &sdhci1;
+		nvmem0 = &eeprom;
 		rtc0 = &rtc;
 		serial0 = &uart0;
 		serial1 = &uart1;
 		serial2 = &dcc;
+		spi0 = &qspi;
+		usb0 = &usb0;
 	};
 
 	chosen {
@@ -150,6 +154,8 @@
 
 &can1 {
 	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_can1_default>;
 };
 
 &dcc {
@@ -192,22 +198,32 @@
 	status = "okay";
 	phy-handle = <&phy0>;
 	phy-mode = "rgmii-id";
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_gem3_default>;
 	phy0: ethernet-phy@21 {
 		reg = <21>;
 		ti,rx-internal-delay = <0x8>;
 		ti,tx-internal-delay = <0xa>;
 		ti,fifo-depth = <0x1>;
 		ti,dp83867-rxctrl-strap-quirk;
+		/* reset-gpios = <&tca6416_u97 6 GPIO_ACTIVE_LOW>; */
 	};
 };
 
 &gpio {
 	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_gpio_default>;
 };
 
 &i2c0 {
 	status = "okay";
 	clock-frequency = <400000>;
+	pinctrl-names = "default", "gpio";
+	pinctrl-0 = <&pinctrl_i2c0_default>;
+	pinctrl-1 = <&pinctrl_i2c0_gpio>;
+	scl-gpios = <&gpio 14 GPIO_ACTIVE_HIGH>;
+	sda-gpios = <&gpio 15 GPIO_ACTIVE_HIGH>;
 
 	tca6416_u97: gpio@20 {
 		compatible = "ti,tca6416";
@@ -451,7 +467,6 @@
 				status = "disabled"; /* unreachable */
 				reg = <0x20>;
 			};
-
 			max20751@72 { /* u95 */
 				compatible = "maxim,max20751";
 				reg = <0x72>;
@@ -468,6 +483,11 @@
 &i2c1 {
 	status = "okay";
 	clock-frequency = <400000>;
+	pinctrl-names = "default", "gpio";
+	pinctrl-0 = <&pinctrl_i2c1_default>;
+	pinctrl-1 = <&pinctrl_i2c1_gpio>;
+	scl-gpios = <&gpio 16 GPIO_ACTIVE_HIGH>;
+	sda-gpios = <&gpio 17 GPIO_ACTIVE_HIGH>;
 
 	/* PL i2c via PCA9306 - u45 */
 	i2c-mux@74 { /* u34 */
@@ -642,6 +662,269 @@
 	};
 };
 
+&pinctrl0 {
+	status = "okay";
+	pinctrl_i2c0_default: i2c0-default {
+		mux {
+			groups = "i2c0_3_grp";
+			function = "i2c0";
+		};
+
+		conf {
+			groups = "i2c0_3_grp";
+			bias-pull-up;
+			slew-rate = <SLEW_RATE_SLOW>;
+			power-source = <IO_STANDARD_LVCMOS18>;
+		};
+	};
+
+	pinctrl_i2c0_gpio: i2c0-gpio {
+		mux {
+			groups = "gpio0_14_grp", "gpio0_15_grp";
+			function = "gpio0";
+		};
+
+		conf {
+			groups = "gpio0_14_grp", "gpio0_15_grp";
+			slew-rate = <SLEW_RATE_SLOW>;
+			power-source = <IO_STANDARD_LVCMOS18>;
+		};
+	};
+
+	pinctrl_i2c1_default: i2c1-default {
+		mux {
+			groups = "i2c1_4_grp";
+			function = "i2c1";
+		};
+
+		conf {
+			groups = "i2c1_4_grp";
+			bias-pull-up;
+			slew-rate = <SLEW_RATE_SLOW>;
+			power-source = <IO_STANDARD_LVCMOS18>;
+		};
+	};
+
+	pinctrl_i2c1_gpio: i2c1-gpio {
+		mux {
+			groups = "gpio0_16_grp", "gpio0_17_grp";
+			function = "gpio0";
+		};
+
+		conf {
+			groups = "gpio0_16_grp", "gpio0_17_grp";
+			slew-rate = <SLEW_RATE_SLOW>;
+			power-source = <IO_STANDARD_LVCMOS18>;
+		};
+	};
+
+	pinctrl_uart0_default: uart0-default {
+		mux {
+			groups = "uart0_4_grp";
+			function = "uart0";
+		};
+
+		conf {
+			groups = "uart0_4_grp";
+			slew-rate = <SLEW_RATE_SLOW>;
+			power-source = <IO_STANDARD_LVCMOS18>;
+		};
+
+		conf-rx {
+			pins = "MIO18";
+			bias-high-impedance;
+		};
+
+		conf-tx {
+			pins = "MIO19";
+			bias-disable;
+		};
+	};
+
+	pinctrl_uart1_default: uart1-default {
+		mux {
+			groups = "uart1_5_grp";
+			function = "uart1";
+		};
+
+		conf {
+			groups = "uart1_5_grp";
+			slew-rate = <SLEW_RATE_SLOW>;
+			power-source = <IO_STANDARD_LVCMOS18>;
+		};
+
+		conf-rx {
+			pins = "MIO21";
+			bias-high-impedance;
+		};
+
+		conf-tx {
+			pins = "MIO20";
+			bias-disable;
+		};
+	};
+
+	pinctrl_usb0_default: usb0-default {
+		mux {
+			groups = "usb0_0_grp";
+			function = "usb0";
+		};
+
+		conf {
+			groups = "usb0_0_grp";
+			slew-rate = <SLEW_RATE_SLOW>;
+			power-source = <IO_STANDARD_LVCMOS18>;
+		};
+
+		conf-rx {
+			pins = "MIO52", "MIO53", "MIO55";
+			bias-high-impedance;
+		};
+
+		conf-tx {
+			pins = "MIO54", "MIO56", "MIO57", "MIO58", "MIO59",
+			       "MIO60", "MIO61", "MIO62", "MIO63";
+			bias-disable;
+		};
+	};
+
+	pinctrl_gem3_default: gem3-default {
+		mux {
+			function = "ethernet3";
+			groups = "ethernet3_0_grp";
+		};
+
+		conf {
+			groups = "ethernet3_0_grp";
+			slew-rate = <SLEW_RATE_SLOW>;
+			power-source = <IO_STANDARD_LVCMOS18>;
+		};
+
+		conf-rx {
+			pins = "MIO70", "MIO71", "MIO72", "MIO73", "MIO74",
+									"MIO75";
+			bias-high-impedance;
+			low-power-disable;
+		};
+
+		conf-tx {
+			pins = "MIO64", "MIO65", "MIO66", "MIO67", "MIO68",
+									"MIO69";
+			bias-disable;
+			low-power-enable;
+		};
+
+		mux-mdio {
+			function = "mdio3";
+			groups = "mdio3_0_grp";
+		};
+
+		conf-mdio {
+			groups = "mdio3_0_grp";
+			slew-rate = <SLEW_RATE_SLOW>;
+			power-source = <IO_STANDARD_LVCMOS18>;
+			bias-disable;
+		};
+	};
+
+	pinctrl_can1_default: can1-default {
+		mux {
+			function = "can1";
+			groups = "can1_6_grp";
+		};
+
+		conf {
+			groups = "can1_6_grp";
+			slew-rate = <SLEW_RATE_SLOW>;
+			power-source = <IO_STANDARD_LVCMOS18>;
+		};
+
+		conf-rx {
+			pins = "MIO25";
+			bias-high-impedance;
+		};
+
+		conf-tx {
+			pins = "MIO24";
+			bias-disable;
+		};
+	};
+
+	pinctrl_sdhci1_default: sdhci1-default {
+		mux {
+			groups = "sdio1_0_grp";
+			function = "sdio1";
+		};
+
+		conf {
+			groups = "sdio1_0_grp";
+			slew-rate = <SLEW_RATE_SLOW>;
+			power-source = <IO_STANDARD_LVCMOS18>;
+			bias-disable;
+		};
+
+		mux-cd {
+			groups = "sdio1_cd_0_grp";
+			function = "sdio1_cd";
+		};
+
+		conf-cd {
+			groups = "sdio1_cd_0_grp";
+			bias-high-impedance;
+			bias-pull-up;
+			slew-rate = <SLEW_RATE_SLOW>;
+			power-source = <IO_STANDARD_LVCMOS18>;
+		};
+
+		mux-wp {
+			groups = "sdio1_wp_0_grp";
+			function = "sdio1_wp";
+		};
+
+		conf-wp {
+			groups = "sdio1_wp_0_grp";
+			bias-high-impedance;
+			bias-pull-up;
+			slew-rate = <SLEW_RATE_SLOW>;
+			power-source = <IO_STANDARD_LVCMOS18>;
+		};
+	};
+
+	pinctrl_gpio_default: gpio-default {
+		mux-sw {
+			function = "gpio0";
+			groups = "gpio0_22_grp", "gpio0_23_grp";
+		};
+
+		conf-sw {
+			groups = "gpio0_22_grp", "gpio0_23_grp";
+			slew-rate = <SLEW_RATE_SLOW>;
+			power-source = <IO_STANDARD_LVCMOS18>;
+		};
+
+		mux-msp {
+			function = "gpio0";
+			groups = "gpio0_13_grp", "gpio0_38_grp";
+		};
+
+		conf-msp {
+			groups = "gpio0_13_grp", "gpio0_38_grp";
+			slew-rate = <SLEW_RATE_SLOW>;
+			power-source = <IO_STANDARD_LVCMOS18>;
+		};
+
+		conf-pull-up {
+			pins = "MIO22", "MIO23";
+			bias-pull-up;
+		};
+
+		conf-pull-none {
+			pins = "MIO13", "MIO38";
+			bias-disable;
+		};
+	};
+};
+
 &pcie {
 	status = "okay";
 };
@@ -653,6 +936,19 @@
 	clock-names = "ref0", "ref1", "ref2", "ref3";
 };
 
+&qspi {
+	status = "okay";
+	flash@0 {
+		compatible = "m25p80", "jedec,spi-nor"; /* 16MB + 16MB */
+		#address-cells = <1>;
+		#size-cells = <1>;
+		reg = <0x0>;
+		spi-tx-bus-width = <1>;
+		spi-rx-bus-width = <4>; /* FIXME also DUAL configuration possible */
+		spi-max-frequency = <108000000>; /* Based on DC1 spec */
+	};
+};
+
 &rtc {
 	status = "okay";
 };
@@ -675,22 +971,42 @@
 /* SD1 with level shifter */
 &sdhci1 {
 	status = "okay";
+	/*
+	 * 1.0 revision has level shifter and this property should be
+	 * removed for supporting UHS mode
+	 */
 	no-1-8-v;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_sdhci1_default>;
 	xlnx,mio-bank = <1>;
 };
 
 &uart0 {
 	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart0_default>;
 };
 
 &uart1 {
 	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart1_default>;
 };
 
 /* ULPI SMSC USB3320 */
 &usb0 {
 	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usb0_default>;
+	phy-names = "usb3-phy";
+	phys = <&psgtr 2 PHY_TYPE_USB3 0 2>;
+};
+
+&dwc3_0 {
+	status = "okay";
 	dr_mode = "host";
+	snps,usb3_lpm_capable;
+	maximum-speed = "super-speed";
 };
 
 &watchdog0 {
diff --git a/arch/arm64/boot/dts/xilinx/zynqmp-zcu102-revB.dts b/arch/arm64/boot/dts/xilinx/zynqmp-zcu102-revB.dts
index d9ad8a4b20d3..f7d718ff116b 100644
--- a/arch/arm64/boot/dts/xilinx/zynqmp-zcu102-revB.dts
+++ b/arch/arm64/boot/dts/xilinx/zynqmp-zcu102-revB.dts
@@ -2,7 +2,7 @@
 /*
  * dts file for Xilinx ZynqMP ZCU102 RevB
  *
- * (C) Copyright 2016 - 2018, Xilinx, Inc.
+ * (C) Copyright 2016 - 2021, Xilinx, Inc.
  *
  * Michal Simek <michal.simek@xilinx.com>
  */
@@ -22,6 +22,7 @@
 		ti,tx-internal-delay = <0xa>;
 		ti,fifo-depth = <0x1>;
 		ti,dp83867-rxctrl-strap-quirk;
+		/* reset-gpios = <&tca6416_u97 6 GPIO_ACTIVE_LOW>; */
 	};
 	/* Cleanup from RevA */
 	/delete-node/ ethernet-phy@21;
diff --git a/arch/arm64/boot/dts/xilinx/zynqmp-zcu104-revA.dts b/arch/arm64/boot/dts/xilinx/zynqmp-zcu104-revA.dts
index 5637e1c17fdf..bd8f20f3223d 100644
--- a/arch/arm64/boot/dts/xilinx/zynqmp-zcu104-revA.dts
+++ b/arch/arm64/boot/dts/xilinx/zynqmp-zcu104-revA.dts
@@ -2,7 +2,7 @@
 /*
  * dts file for Xilinx ZynqMP ZCU104
  *
- * (C) Copyright 2017 - 2019, Xilinx, Inc.
+ * (C) Copyright 2017 - 2021, Xilinx, Inc.
  *
  * Michal Simek <michal.simek@xilinx.com>
  */
@@ -12,6 +12,7 @@
 #include "zynqmp.dtsi"
 #include "zynqmp-clk-ccf.dtsi"
 #include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/pinctrl/pinctrl-zynqmp.h>
 #include <dt-bindings/phy/phy.h>
 
 / {
@@ -22,10 +23,13 @@
 		ethernet0 = &gem3;
 		i2c0 = &i2c1;
 		mmc0 = &sdhci1;
+		nvmem0 = &eeprom;
 		rtc0 = &rtc;
 		serial0 = &uart0;
 		serial1 = &uart1;
 		serial2 = &dcc;
+		spi0 = &qspi;
+		usb0 = &usb0;
 	};
 
 	chosen {
@@ -59,16 +63,52 @@
 
 &can1 {
 	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_can1_default>;
 };
 
 &dcc {
 	status = "okay";
 };
 
+&fpd_dma_chan1 {
+	status = "okay";
+};
+
+&fpd_dma_chan2 {
+	status = "okay";
+};
+
+&fpd_dma_chan3 {
+	status = "okay";
+};
+
+&fpd_dma_chan4 {
+	status = "okay";
+};
+
+&fpd_dma_chan5 {
+	status = "okay";
+};
+
+&fpd_dma_chan6 {
+	status = "okay";
+};
+
+&fpd_dma_chan7 {
+	status = "okay";
+};
+
+&fpd_dma_chan8 {
+	status = "okay";
+};
+
 &gem3 {
 	status = "okay";
 	phy-handle = <&phy0>;
 	phy-mode = "rgmii-id";
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_gem3_default>;
 	phy0: ethernet-phy@c {
 		reg = <0xc>;
 		ti,rx-internal-delay = <0x8>;
@@ -85,6 +125,11 @@
 &i2c1 {
 	status = "okay";
 	clock-frequency = <400000>;
+	pinctrl-names = "default", "gpio";
+	pinctrl-0 = <&pinctrl_i2c1_default>;
+	pinctrl-1 = <&pinctrl_i2c1_gpio>;
+	scl-gpios = <&gpio 16 GPIO_ACTIVE_HIGH>;
+	sda-gpios = <&gpio 17 GPIO_ACTIVE_HIGH>;
 
 	/* Another connection to this bus via PL i2c via PCA9306 - u45 */
 	i2c-mux@74 { /* u34 */
@@ -104,7 +149,7 @@
 			 * 512B - 768B address 0x56
 			 * 768B - 1024B address 0x57
 			 */
-			eeprom@54 { /* u23 */
+			eeprom: eeprom@54 { /* u23 */
 				compatible = "atmel,24c08";
 				reg = <0x54>;
 				#address-cells = <1>;
@@ -116,20 +161,20 @@
 			#address-cells = <1>;
 			#size-cells = <0>;
 			reg = <1>;
-			clock_8t49n287: clock-generator@6c { /* 8T49N287 - u182 */
-				reg = <0x6c>;
-			};
+			/* 8T49N287 - u182 */
 		};
 
 		i2c@2 {
 			#address-cells = <1>;
 			#size-cells = <0>;
 			reg = <2>;
-			irps5401_43: irps54012@43 { /* IRPS5401 - u175 */
-				reg = <0x43>;
+			irps5401_43: irps5401@43 { /* IRPS5401 - u175 */
+				compatible = "infineon,irps5401";
+				reg = <0x43>; /* pmbus / i2c 0x13 */
 			};
-			irps5401_4d: irps54012@4d { /* IRPS5401 - u180 */
-				reg = <0x4d>;
+			irps5401_44: irps5401@44 { /* IRPS5401 - u180 */
+				compatible = "infineon,irps5401";
+				reg = <0x44>; /* pmbus / i2c 0x14 */
 			};
 		};
 
@@ -173,8 +218,202 @@
 	};
 };
 
-&rtc {
+&pinctrl0 {
 	status = "okay";
+
+	pinctrl_can1_default: can1-default {
+		mux {
+			function = "can1";
+			groups = "can1_6_grp";
+		};
+
+		conf {
+			groups = "can1_6_grp";
+			slew-rate = <SLEW_RATE_SLOW>;
+			power-source = <IO_STANDARD_LVCMOS18>;
+			drive-strength = <12>;
+		};
+
+		conf-rx {
+			pins = "MIO25";
+			bias-high-impedance;
+		};
+
+		conf-tx {
+			pins = "MIO24";
+			bias-disable;
+		};
+	};
+
+	pinctrl_i2c1_default: i2c1-default {
+		mux {
+			groups = "i2c1_4_grp";
+			function = "i2c1";
+		};
+
+		conf {
+			groups = "i2c1_4_grp";
+			bias-pull-up;
+			slew-rate = <SLEW_RATE_SLOW>;
+			power-source = <IO_STANDARD_LVCMOS18>;
+			drive-strength = <12>;
+		};
+	};
+
+	pinctrl_i2c1_gpio: i2c1-gpio {
+		mux {
+			groups = "gpio0_16_grp", "gpio0_17_grp";
+			function = "gpio0";
+		};
+
+		conf {
+			groups = "gpio0_16_grp", "gpio0_17_grp";
+			slew-rate = <SLEW_RATE_SLOW>;
+			power-source = <IO_STANDARD_LVCMOS18>;
+			drive-strength = <12>;
+		};
+	};
+
+	pinctrl_gem3_default: gem3-default {
+		mux {
+			function = "ethernet3";
+			groups = "ethernet3_0_grp";
+		};
+
+		conf {
+			groups = "ethernet3_0_grp";
+			slew-rate = <SLEW_RATE_SLOW>;
+			power-source = <IO_STANDARD_LVCMOS18>;
+			drive-strength = <12>;
+		};
+
+		conf-rx {
+			pins = "MIO70", "MIO71", "MIO72", "MIO73", "MIO74",
+									"MIO75";
+			bias-high-impedance;
+			low-power-disable;
+		};
+
+		conf-tx {
+			pins = "MIO64", "MIO65", "MIO66", "MIO67", "MIO68",
+									"MIO69";
+			bias-disable;
+			low-power-enable;
+		};
+
+		mux-mdio {
+			function = "mdio3";
+			groups = "mdio3_0_grp";
+		};
+
+		conf-mdio {
+			groups = "mdio3_0_grp";
+			slew-rate = <SLEW_RATE_SLOW>;
+			power-source = <IO_STANDARD_LVCMOS18>;
+			bias-disable;
+		};
+	};
+
+	pinctrl_sdhci1_default: sdhci1-default {
+		mux {
+			groups = "sdio1_0_grp";
+			function = "sdio1";
+		};
+
+		conf {
+			groups = "sdio1_0_grp";
+			slew-rate = <SLEW_RATE_SLOW>;
+			power-source = <IO_STANDARD_LVCMOS18>;
+			bias-disable;
+			drive-strength = <12>;
+		};
+
+		mux-cd {
+			groups = "sdio1_cd_0_grp";
+			function = "sdio1_cd";
+		};
+
+		conf-cd {
+			groups = "sdio1_cd_0_grp";
+			bias-high-impedance;
+			bias-pull-up;
+			slew-rate = <SLEW_RATE_SLOW>;
+			power-source = <IO_STANDARD_LVCMOS18>;
+		};
+	};
+
+	pinctrl_uart0_default: uart0-default {
+		mux {
+			groups = "uart0_4_grp";
+			function = "uart0";
+		};
+
+		conf {
+			groups = "uart0_4_grp";
+			slew-rate = <SLEW_RATE_SLOW>;
+			power-source = <IO_STANDARD_LVCMOS18>;
+			drive-strength = <12>;
+		};
+
+		conf-rx {
+			pins = "MIO18";
+			bias-high-impedance;
+		};
+
+		conf-tx {
+			pins = "MIO19";
+			bias-disable;
+		};
+	};
+
+	pinctrl_uart1_default: uart1-default {
+		mux {
+			groups = "uart1_5_grp";
+			function = "uart1";
+		};
+
+		conf {
+			groups = "uart1_5_grp";
+			slew-rate = <SLEW_RATE_SLOW>;
+			power-source = <IO_STANDARD_LVCMOS18>;
+			drive-strength = <12>;
+		};
+
+		conf-rx {
+			pins = "MIO21";
+			bias-high-impedance;
+		};
+
+		conf-tx {
+			pins = "MIO20";
+			bias-disable;
+		};
+	};
+
+	pinctrl_usb0_default: usb0-default {
+		mux {
+			groups = "usb0_0_grp";
+			function = "usb0";
+		};
+
+		conf {
+			groups = "usb0_0_grp";
+			slew-rate = <SLEW_RATE_SLOW>;
+			power-source = <IO_STANDARD_LVCMOS18>;
+			drive-strength = <12>;
+		};
+
+		conf-rx {
+			pins = "MIO52", "MIO53", "MIO55";
+			bias-high-impedance;
+		};
+
+		conf-tx {
+			pins = "MIO54", "MIO56", "MIO57", "MIO58", "MIO59",
+			       "MIO60", "MIO61", "MIO62", "MIO63";
+			bias-disable;
+		};
+	};
 };
 
 &psgtr {
@@ -184,6 +423,23 @@
 	clock-names = "ref1", "ref2", "ref3";
 };
 
+&qspi {
+	status = "okay";
+	flash@0 {
+		compatible = "m25p80", "jedec,spi-nor"; /* n25q512a 128MiB */
+		#address-cells = <1>;
+		#size-cells = <1>;
+		reg = <0x0>;
+		spi-tx-bus-width = <1>;
+		spi-rx-bus-width = <4>;
+		spi-max-frequency = <108000000>; /* Based on DC1 spec */
+	};
+};
+
+&rtc {
+	status = "okay";
+};
+
 &sata {
 	status = "okay";
 	/* SATA OOB timing settings */
@@ -203,22 +459,38 @@
 &sdhci1 {
 	status = "okay";
 	no-1-8-v;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_sdhci1_default>;
 	xlnx,mio-bank = <1>;
 	disable-wp;
 };
 
 &uart0 {
 	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart0_default>;
 };
 
 &uart1 {
 	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart1_default>;
 };
 
 /* ULPI SMSC USB3320 */
 &usb0 {
 	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usb0_default>;
+	phy-names = "usb3-phy";
+	phys = <&psgtr 2 PHY_TYPE_USB3 0 2>;
+};
+
+&dwc3_0 {
+	status = "okay";
 	dr_mode = "host";
+	snps,usb3_lpm_capable;
+	maximum-speed = "super-speed";
 };
 
 &watchdog0 {
diff --git a/arch/arm64/boot/dts/xilinx/zynqmp-zcu104-revC.dts b/arch/arm64/boot/dts/xilinx/zynqmp-zcu104-revC.dts
index 7f2e32831b05..96feaad30166 100644
--- a/arch/arm64/boot/dts/xilinx/zynqmp-zcu104-revC.dts
+++ b/arch/arm64/boot/dts/xilinx/zynqmp-zcu104-revC.dts
@@ -2,7 +2,7 @@
 /*
  * dts file for Xilinx ZynqMP ZCU104
  *
- * (C) Copyright 2017 - 2020, Xilinx, Inc.
+ * (C) Copyright 2017 - 2021, Xilinx, Inc.
  *
  * Michal Simek <michal.simek@xilinx.com>
  */
@@ -12,6 +12,7 @@
 #include "zynqmp.dtsi"
 #include "zynqmp-clk-ccf.dtsi"
 #include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/pinctrl/pinctrl-zynqmp.h>
 #include <dt-bindings/phy/phy.h>
 
 / {
@@ -22,10 +23,13 @@
 		ethernet0 = &gem3;
 		i2c0 = &i2c1;
 		mmc0 = &sdhci1;
+		nvmem0 = &eeprom;
 		rtc0 = &rtc;
 		serial0 = &uart0;
 		serial1 = &uart1;
 		serial2 = &dcc;
+		spi0 = &qspi;
+		usb0 = &usb0;
 	};
 
 	chosen {
@@ -64,6 +68,8 @@
 
 &can1 {
 	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_can1_default>;
 };
 
 &dcc {
@@ -106,6 +112,8 @@
 	status = "okay";
 	phy-handle = <&phy0>;
 	phy-mode = "rgmii-id";
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_gem3_default>;
 	phy0: ethernet-phy@c {
 		reg = <0xc>;
 		ti,rx-internal-delay = <0x8>;
@@ -122,6 +130,11 @@
 &i2c1 {
 	status = "okay";
 	clock-frequency = <400000>;
+	pinctrl-names = "default", "gpio";
+	pinctrl-0 = <&pinctrl_i2c1_default>;
+	pinctrl-1 = <&pinctrl_i2c1_gpio>;
+	scl-gpios = <&gpio 16 GPIO_ACTIVE_HIGH>;
+	sda-gpios = <&gpio 17 GPIO_ACTIVE_HIGH>;
 
 	tca6416_u97: gpio@20 {
 		compatible = "ti,tca6416";
@@ -172,9 +185,7 @@
 			#address-cells = <1>;
 			#size-cells = <0>;
 			reg = <1>;
-			clock_8t49n287: clock-generator@6c { /* 8T49N287 - u182 */
-				reg = <0x6c>;
-			};
+			/* 8T49N287 - u182 */
 		};
 
 		i2c@2 {
@@ -219,6 +230,211 @@
 	};
 };
 
+&pinctrl0 {
+	status = "okay";
+
+	pinctrl_can1_default: can1-default {
+		mux {
+			function = "can1";
+			groups = "can1_6_grp";
+		};
+
+		conf {
+			groups = "can1_6_grp";
+			slew-rate = <SLEW_RATE_SLOW>;
+			power-source = <IO_STANDARD_LVCMOS18>;
+			drive-strength = <12>;
+		};
+
+		conf-rx {
+			pins = "MIO25";
+			bias-high-impedance;
+		};
+
+		conf-tx {
+			pins = "MIO24";
+			bias-disable;
+		};
+	};
+
+	pinctrl_i2c1_default: i2c1-default {
+		mux {
+			groups = "i2c1_4_grp";
+			function = "i2c1";
+		};
+
+		conf {
+			groups = "i2c1_4_grp";
+			bias-pull-up;
+			slew-rate = <SLEW_RATE_SLOW>;
+			power-source = <IO_STANDARD_LVCMOS18>;
+			drive-strength = <12>;
+		};
+	};
+
+	pinctrl_i2c1_gpio: i2c1-gpio {
+		mux {
+			groups = "gpio0_16_grp", "gpio0_17_grp";
+			function = "gpio0";
+		};
+
+		conf {
+			groups = "gpio0_16_grp", "gpio0_17_grp";
+			slew-rate = <SLEW_RATE_SLOW>;
+			power-source = <IO_STANDARD_LVCMOS18>;
+			drive-strength = <12>;
+		};
+	};
+
+	pinctrl_gem3_default: gem3-default {
+		mux {
+			function = "ethernet3";
+			groups = "ethernet3_0_grp";
+		};
+
+		conf {
+			groups = "ethernet3_0_grp";
+			slew-rate = <SLEW_RATE_SLOW>;
+			power-source = <IO_STANDARD_LVCMOS18>;
+			drive-strength = <12>;
+		};
+
+		conf-rx {
+			pins = "MIO70", "MIO71", "MIO72", "MIO73", "MIO74",
+									"MIO75";
+			bias-high-impedance;
+			low-power-disable;
+		};
+
+		conf-tx {
+			pins = "MIO64", "MIO65", "MIO66", "MIO67", "MIO68",
+									"MIO69";
+			bias-disable;
+			low-power-enable;
+		};
+
+		mux-mdio {
+			function = "mdio3";
+			groups = "mdio3_0_grp";
+		};
+
+		conf-mdio {
+			groups = "mdio3_0_grp";
+			slew-rate = <SLEW_RATE_SLOW>;
+			power-source = <IO_STANDARD_LVCMOS18>;
+			bias-disable;
+		};
+	};
+
+	pinctrl_sdhci1_default: sdhci1-default {
+		mux {
+			groups = "sdio1_0_grp";
+			function = "sdio1";
+		};
+
+		conf {
+			groups = "sdio1_0_grp";
+			slew-rate = <SLEW_RATE_SLOW>;
+			power-source = <IO_STANDARD_LVCMOS18>;
+			bias-disable;
+			drive-strength = <12>;
+		};
+
+		mux-cd {
+			groups = "sdio1_cd_0_grp";
+			function = "sdio1_cd";
+		};
+
+		conf-cd {
+			groups = "sdio1_cd_0_grp";
+			bias-high-impedance;
+			bias-pull-up;
+			slew-rate = <SLEW_RATE_SLOW>;
+			power-source = <IO_STANDARD_LVCMOS18>;
+		};
+	};
+
+	pinctrl_uart0_default: uart0-default {
+		mux {
+			groups = "uart0_4_grp";
+			function = "uart0";
+		};
+
+		conf {
+			groups = "uart0_4_grp";
+			slew-rate = <SLEW_RATE_SLOW>;
+			power-source = <IO_STANDARD_LVCMOS18>;
+			drive-strength = <12>;
+		};
+
+		conf-rx {
+			pins = "MIO18";
+			bias-high-impedance;
+		};
+
+		conf-tx {
+			pins = "MIO19";
+			bias-disable;
+		};
+	};
+
+	pinctrl_uart1_default: uart1-default {
+		mux {
+			groups = "uart1_5_grp";
+			function = "uart1";
+		};
+
+		conf {
+			groups = "uart1_5_grp";
+			slew-rate = <SLEW_RATE_SLOW>;
+			power-source = <IO_STANDARD_LVCMOS18>;
+			drive-strength = <12>;
+		};
+
+		conf-rx {
+			pins = "MIO21";
+			bias-high-impedance;
+		};
+
+		conf-tx {
+			pins = "MIO20";
+			bias-disable;
+		};
+	};
+
+	pinctrl_usb0_default: usb0-default {
+		mux {
+			groups = "usb0_0_grp";
+			function = "usb0";
+		};
+
+		conf {
+			groups = "usb0_0_grp";
+			slew-rate = <SLEW_RATE_SLOW>;
+			power-source = <IO_STANDARD_LVCMOS18>;
+			drive-strength = <12>;
+		};
+
+		conf-rx {
+			pins = "MIO52", "MIO53", "MIO55";
+			bias-high-impedance;
+		};
+
+		conf-tx {
+			pins = "MIO54", "MIO56", "MIO57", "MIO58", "MIO59",
+			       "MIO60", "MIO61", "MIO62", "MIO63";
+			bias-disable;
+		};
+	};
+};
+
+&psgtr {
+	status = "okay";
+	/* nc, sata, usb3, dp */
+	clocks = <&clock_8t49n287_5>, <&clock_8t49n287_2>, <&clock_8t49n287_3>;
+	clock-names = "ref1", "ref2", "ref3";
+};
+
 &qspi {
 	status = "okay";
 	flash@0 {
@@ -226,6 +442,9 @@
 		#address-cells = <1>;
 		#size-cells = <1>;
 		reg = <0x0>;
+		spi-tx-bus-width = <1>;
+		spi-rx-bus-width = <4>;
+		spi-max-frequency = <108000000>; /* Based on DC1 spec */
 	};
 };
 
@@ -233,13 +452,6 @@
 	status = "okay";
 };
 
-&psgtr {
-	status = "okay";
-	/* nc, sata, usb3, dp */
-	clocks = <&clock_8t49n287_5>, <&clock_8t49n287_2>, <&clock_8t49n287_3>;
-	clock-names = "ref1", "ref2", "ref3";
-};
-
 &sata {
 	status = "okay";
 	/* SATA OOB timing settings */
@@ -259,22 +471,38 @@
 &sdhci1 {
 	status = "okay";
 	no-1-8-v;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_sdhci1_default>;
 	xlnx,mio-bank = <1>;
 	disable-wp;
 };
 
 &uart0 {
 	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart0_default>;
 };
 
 &uart1 {
 	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart1_default>;
 };
 
 /* ULPI SMSC USB3320 */
 &usb0 {
 	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usb0_default>;
+	phy-names = "usb3-phy";
+	phys = <&psgtr 2 PHY_TYPE_USB3 0 2>;
+};
+
+&dwc3_0 {
+	status = "okay";
 	dr_mode = "host";
+	snps,usb3_lpm_capable;
+	maximum-speed = "super-speed";
 };
 
 &watchdog0 {
diff --git a/arch/arm64/boot/dts/xilinx/zynqmp-zcu106-revA.dts b/arch/arm64/boot/dts/xilinx/zynqmp-zcu106-revA.dts
index eff7c6447087..20b7c75bb1d3 100644
--- a/arch/arm64/boot/dts/xilinx/zynqmp-zcu106-revA.dts
+++ b/arch/arm64/boot/dts/xilinx/zynqmp-zcu106-revA.dts
@@ -2,7 +2,7 @@
 /*
  * dts file for Xilinx ZynqMP ZCU106
  *
- * (C) Copyright 2016 - 2019, Xilinx, Inc.
+ * (C) Copyright 2016 - 2021, Xilinx, Inc.
  *
  * Michal Simek <michal.simek@xilinx.com>
  */
@@ -13,6 +13,7 @@
 #include "zynqmp-clk-ccf.dtsi"
 #include <dt-bindings/input/input.h>
 #include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/pinctrl/pinctrl-zynqmp.h>
 #include <dt-bindings/phy/phy.h>
 
 / {
@@ -24,10 +25,13 @@
 		i2c0 = &i2c0;
 		i2c1 = &i2c1;
 		mmc0 = &sdhci1;
+		nvmem0 = &eeprom;
 		rtc0 = &rtc;
 		serial0 = &uart0;
 		serial1 = &uart1;
 		serial2 = &dcc;
+		spi0 = &qspi;
+		usb0 = &usb0;
 	};
 
 	chosen {
@@ -150,24 +154,14 @@
 
 &can1 {
 	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_can1_default>;
 };
 
 &dcc {
 	status = "okay";
 };
 
-&zynqmp_dpdma {
-	status = "okay";
-};
-
-&zynqmp_dpsub {
-	status = "okay";
-	phy-names = "dp-phy0", "dp-phy1";
-	phys = <&psgtr 1 PHY_TYPE_DP 0 3>,
-	       <&psgtr 0 PHY_TYPE_DP 1 3>;
-};
-
-/* fpd_dma clk 667MHz, lpd_dma 500MHz */
 &fpd_dma_chan1 {
 	status = "okay";
 };
@@ -204,6 +198,8 @@
 	status = "okay";
 	phy-handle = <&phy0>;
 	phy-mode = "rgmii-id";
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_gem3_default>;
 	phy0: ethernet-phy@c {
 		reg = <0xc>;
 		ti,rx-internal-delay = <0x8>;
@@ -215,11 +211,18 @@
 
 &gpio {
 	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_gpio_default>;
 };
 
 &i2c0 {
 	status = "okay";
 	clock-frequency = <400000>;
+	pinctrl-names = "default", "gpio";
+	pinctrl-0 = <&pinctrl_i2c0_default>;
+	pinctrl-1 = <&pinctrl_i2c0_gpio>;
+	scl-gpios = <&gpio 14 GPIO_ACTIVE_HIGH>;
+	sda-gpios = <&gpio 15 GPIO_ACTIVE_HIGH>;
 
 	tca6416_u97: gpio@20 {
 		compatible = "ti,tca6416";
@@ -478,6 +481,11 @@
 &i2c1 {
 	status = "okay";
 	clock-frequency = <400000>;
+	pinctrl-names = "default", "gpio";
+	pinctrl-0 = <&pinctrl_i2c1_default>;
+	pinctrl-1 = <&pinctrl_i2c1_gpio>;
+	scl-gpios = <&gpio 16 GPIO_ACTIVE_HIGH>;
+	sda-gpios = <&gpio 17 GPIO_ACTIVE_HIGH>;
 
 	/* PL i2c via PCA9306 - u45 */
 	i2c-mux@74 { /* u34 */
@@ -652,6 +660,269 @@
 	};
 };
 
+&pinctrl0 {
+	status = "okay";
+	pinctrl_i2c0_default: i2c0-default {
+		mux {
+			groups = "i2c0_3_grp";
+			function = "i2c0";
+		};
+
+		conf {
+			groups = "i2c0_3_grp";
+			bias-pull-up;
+			slew-rate = <SLEW_RATE_SLOW>;
+			power-source = <IO_STANDARD_LVCMOS18>;
+		};
+	};
+
+	pinctrl_i2c0_gpio: i2c0-gpio {
+		mux {
+			groups = "gpio0_14_grp", "gpio0_15_grp";
+			function = "gpio0";
+		};
+
+		conf {
+			groups = "gpio0_14_grp", "gpio0_15_grp";
+			slew-rate = <SLEW_RATE_SLOW>;
+			power-source = <IO_STANDARD_LVCMOS18>;
+		};
+	};
+
+	pinctrl_i2c1_default: i2c1-default {
+		mux {
+			groups = "i2c1_4_grp";
+			function = "i2c1";
+		};
+
+		conf {
+			groups = "i2c1_4_grp";
+			bias-pull-up;
+			slew-rate = <SLEW_RATE_SLOW>;
+			power-source = <IO_STANDARD_LVCMOS18>;
+		};
+	};
+
+	pinctrl_i2c1_gpio: i2c1-gpio {
+		mux {
+			groups = "gpio0_16_grp", "gpio0_17_grp";
+			function = "gpio0";
+		};
+
+		conf {
+			groups = "gpio0_16_grp", "gpio0_17_grp";
+			slew-rate = <SLEW_RATE_SLOW>;
+			power-source = <IO_STANDARD_LVCMOS18>;
+		};
+	};
+
+	pinctrl_uart0_default: uart0-default {
+		mux {
+			groups = "uart0_4_grp";
+			function = "uart0";
+		};
+
+		conf {
+			groups = "uart0_4_grp";
+			slew-rate = <SLEW_RATE_SLOW>;
+			power-source = <IO_STANDARD_LVCMOS18>;
+		};
+
+		conf-rx {
+			pins = "MIO18";
+			bias-high-impedance;
+		};
+
+		conf-tx {
+			pins = "MIO19";
+			bias-disable;
+		};
+	};
+
+	pinctrl_uart1_default: uart1-default {
+		mux {
+			groups = "uart1_5_grp";
+			function = "uart1";
+		};
+
+		conf {
+			groups = "uart1_5_grp";
+			slew-rate = <SLEW_RATE_SLOW>;
+			power-source = <IO_STANDARD_LVCMOS18>;
+		};
+
+		conf-rx {
+			pins = "MIO21";
+			bias-high-impedance;
+		};
+
+		conf-tx {
+			pins = "MIO20";
+			bias-disable;
+		};
+	};
+
+	pinctrl_usb0_default: usb0-default {
+		mux {
+			groups = "usb0_0_grp";
+			function = "usb0";
+		};
+
+		conf {
+			groups = "usb0_0_grp";
+			slew-rate = <SLEW_RATE_SLOW>;
+			power-source = <IO_STANDARD_LVCMOS18>;
+		};
+
+		conf-rx {
+			pins = "MIO52", "MIO53", "MIO55";
+			bias-high-impedance;
+		};
+
+		conf-tx {
+			pins = "MIO54", "MIO56", "MIO57", "MIO58", "MIO59",
+			       "MIO60", "MIO61", "MIO62", "MIO63";
+			bias-disable;
+		};
+	};
+
+	pinctrl_gem3_default: gem3-default {
+		mux {
+			function = "ethernet3";
+			groups = "ethernet3_0_grp";
+		};
+
+		conf {
+			groups = "ethernet3_0_grp";
+			slew-rate = <SLEW_RATE_SLOW>;
+			power-source = <IO_STANDARD_LVCMOS18>;
+		};
+
+		conf-rx {
+			pins = "MIO70", "MIO71", "MIO72", "MIO73", "MIO74",
+									"MIO75";
+			bias-high-impedance;
+			low-power-disable;
+		};
+
+		conf-tx {
+			pins = "MIO64", "MIO65", "MIO66", "MIO67", "MIO68",
+									"MIO69";
+			bias-disable;
+			low-power-enable;
+		};
+
+		mux-mdio {
+			function = "mdio3";
+			groups = "mdio3_0_grp";
+		};
+
+		conf-mdio {
+			groups = "mdio3_0_grp";
+			slew-rate = <SLEW_RATE_SLOW>;
+			power-source = <IO_STANDARD_LVCMOS18>;
+			bias-disable;
+		};
+	};
+
+	pinctrl_can1_default: can1-default {
+		mux {
+			function = "can1";
+			groups = "can1_6_grp";
+		};
+
+		conf {
+			groups = "can1_6_grp";
+			slew-rate = <SLEW_RATE_SLOW>;
+			power-source = <IO_STANDARD_LVCMOS18>;
+		};
+
+		conf-rx {
+			pins = "MIO25";
+			bias-high-impedance;
+		};
+
+		conf-tx {
+			pins = "MIO24";
+			bias-disable;
+		};
+	};
+
+	pinctrl_sdhci1_default: sdhci1-default {
+		mux {
+			groups = "sdio1_0_grp";
+			function = "sdio1";
+		};
+
+		conf {
+			groups = "sdio1_0_grp";
+			slew-rate = <SLEW_RATE_SLOW>;
+			power-source = <IO_STANDARD_LVCMOS18>;
+			bias-disable;
+		};
+
+		mux-cd {
+			groups = "sdio1_cd_0_grp";
+			function = "sdio1_cd";
+		};
+
+		conf-cd {
+			groups = "sdio1_cd_0_grp";
+			bias-high-impedance;
+			bias-pull-up;
+			slew-rate = <SLEW_RATE_SLOW>;
+			power-source = <IO_STANDARD_LVCMOS18>;
+		};
+
+		mux-wp {
+			groups = "sdio1_wp_0_grp";
+			function = "sdio1_wp";
+		};
+
+		conf-wp {
+			groups = "sdio1_wp_0_grp";
+			bias-high-impedance;
+			bias-pull-up;
+			slew-rate = <SLEW_RATE_SLOW>;
+			power-source = <IO_STANDARD_LVCMOS18>;
+		};
+	};
+
+	pinctrl_gpio_default: gpio-default {
+		mux {
+			function = "gpio0";
+			groups = "gpio0_22_grp", "gpio0_23_grp";
+		};
+
+		conf {
+			groups = "gpio0_22_grp", "gpio0_23_grp";
+			slew-rate = <SLEW_RATE_SLOW>;
+			power-source = <IO_STANDARD_LVCMOS18>;
+		};
+
+		mux-msp {
+			function = "gpio0";
+			groups = "gpio0_13_grp", "gpio0_38_grp";
+		};
+
+		conf-msp {
+			groups = "gpio0_13_grp", "gpio0_38_grp";
+			slew-rate = <SLEW_RATE_SLOW>;
+			power-source = <IO_STANDARD_LVCMOS18>;
+		};
+
+		conf-pull-up {
+			pins = "MIO22";
+			bias-pull-up;
+		};
+
+		conf-pull-none {
+			pins = "MIO13", "MIO23", "MIO38";
+			bias-disable;
+		};
+	};
+};
+
 &psgtr {
 	status = "okay";
 	/* nc, sata, usb3, dp */
@@ -659,6 +930,19 @@
 	clock-names = "ref1", "ref2", "ref3";
 };
 
+&qspi {
+	status = "okay";
+	flash@0 {
+		compatible = "m25p80", "jedec,spi-nor"; /* 16MB + 16MB */
+		#address-cells = <1>;
+		#size-cells = <1>;
+		reg = <0x0>;
+		spi-tx-bus-width = <1>;
+		spi-rx-bus-width = <4>; /* FIXME also DUAL configuration possible */
+		spi-max-frequency = <108000000>; /* Based on DC1 spec */
+	};
+};
+
 &rtc {
 	status = "okay";
 };
@@ -681,24 +965,54 @@
 /* SD1 with level shifter */
 &sdhci1 {
 	status = "okay";
+	/*
+	 * This property should be removed for supporting UHS mode
+	 */
 	no-1-8-v;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_sdhci1_default>;
 	xlnx,mio-bank = <1>;
 };
 
 &uart0 {
 	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart0_default>;
 };
 
 &uart1 {
 	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart1_default>;
 };
 
 /* ULPI SMSC USB3320 */
 &usb0 {
 	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usb0_default>;
+	phy-names = "usb3-phy";
+	phys = <&psgtr 2 PHY_TYPE_USB3 0 2>;
+};
+
+&dwc3_0 {
+	status = "okay";
 	dr_mode = "host";
+	snps,usb3_lpm_capable;
+	maximum-speed = "super-speed";
 };
 
 &watchdog0 {
 	status = "okay";
 };
+
+&zynqmp_dpdma {
+	status = "okay";
+};
+
+&zynqmp_dpsub {
+	status = "okay";
+	phy-names = "dp-phy0", "dp-phy1";
+	phys = <&psgtr 1 PHY_TYPE_DP 0 3>,
+	       <&psgtr 0 PHY_TYPE_DP 1 3>;
+};
diff --git a/arch/arm64/boot/dts/xilinx/zynqmp-zcu111-revA.dts b/arch/arm64/boot/dts/xilinx/zynqmp-zcu111-revA.dts
index d4b68f0d0098..e36df6adbeee 100644
--- a/arch/arm64/boot/dts/xilinx/zynqmp-zcu111-revA.dts
+++ b/arch/arm64/boot/dts/xilinx/zynqmp-zcu111-revA.dts
@@ -2,7 +2,7 @@
 /*
  * dts file for Xilinx ZynqMP ZCU111
  *
- * (C) Copyright 2017 - 2019, Xilinx, Inc.
+ * (C) Copyright 2017 - 2021, Xilinx, Inc.
  *
  * Michal Simek <michal.simek@xilinx.com>
  */
@@ -13,6 +13,7 @@
 #include "zynqmp-clk-ccf.dtsi"
 #include <dt-bindings/input/input.h>
 #include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/pinctrl/pinctrl-zynqmp.h>
 #include <dt-bindings/phy/phy.h>
 
 / {
@@ -24,9 +25,12 @@
 		i2c0 = &i2c0;
 		i2c1 = &i2c1;
 		mmc0 = &sdhci1;
+		nvmem0 = &eeprom;
 		rtc0 = &rtc;
 		serial0 = &uart0;
 		serial1 = &dcc;
+		spi0 = &qspi;
+		usb0 = &usb0;
 	};
 
 	chosen {
@@ -166,6 +170,8 @@
 	status = "okay";
 	phy-handle = <&phy0>;
 	phy-mode = "rgmii-id";
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_gem3_default>;
 	phy0: ethernet-phy@c {
 		reg = <0xc>;
 		ti,rx-internal-delay = <0x8>;
@@ -177,11 +183,18 @@
 
 &gpio {
 	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_gpio_default>;
 };
 
 &i2c0 {
 	status = "okay";
 	clock-frequency = <400000>;
+	pinctrl-names = "default", "gpio";
+	pinctrl-0 = <&pinctrl_i2c0_default>;
+	pinctrl-1 = <&pinctrl_i2c0_gpio>;
+	scl-gpios = <&gpio 14 GPIO_ACTIVE_HIGH>;
+	sda-gpios = <&gpio 15 GPIO_ACTIVE_HIGH>;
 
 	tca6416_u22: gpio@20 {
 		compatible = "ti,tca6416";
@@ -326,13 +339,16 @@
 			#address-cells = <1>;
 			#size-cells = <0>;
 			reg = <2>;
-			irps5401_43: irps54012@43 { /* IRPS5401 - u53 check these */
+			irps5401_43: irps5401@43 { /* IRPS5401 - u53 check these */
+				compatible = "infineon,irps5401";
 				reg = <0x43>;
 			};
-			irps5401_44: irps54012@44 { /* IRPS5401 - u55 */
+			irps5401_44: irps5401@44 { /* IRPS5401 - u55 */
+				compatible = "infineon,irps5401";
 				reg = <0x44>;
 			};
-			irps5401_45: irps54012@45 { /* IRPS5401 - u57 */
+			irps5401_45: irps5401@45 { /* IRPS5401 - u57 */
+				compatible = "infineon,irps5401";
 				reg = <0x45>;
 			};
 			/* u68 IR38064 +0 */
@@ -354,6 +370,11 @@
 &i2c1 {
 	status = "okay";
 	clock-frequency = <400000>;
+	pinctrl-names = "default", "gpio";
+	pinctrl-0 = <&pinctrl_i2c1_default>;
+	pinctrl-1 = <&pinctrl_i2c1_gpio>;
+	scl-gpios = <&gpio 16 GPIO_ACTIVE_HIGH>;
+	sda-gpios = <&gpio 17 GPIO_ACTIVE_HIGH>;
 
 	i2c-mux@74 { /* u26 */
 		compatible = "nxp,pca9548";
@@ -455,9 +476,7 @@
 			#address-cells = <1>;
 			#size-cells = <0>;
 			reg = <4>;
-			si5382: clock-generator@69 { /* SI5382 - u48 */
-				reg = <0x69>;
-			};
+			/* SI5382 - u48 */
 		};
 		i2c@5 {
 			#address-cells = <1>;
@@ -542,13 +561,230 @@
 	};
 };
 
+&pinctrl0 {
+	status = "okay";
+	pinctrl_i2c0_default: i2c0-default {
+		mux {
+			groups = "i2c0_3_grp";
+			function = "i2c0";
+		};
+
+		conf {
+			groups = "i2c0_3_grp";
+			bias-pull-up;
+			slew-rate = <SLEW_RATE_SLOW>;
+			power-source = <IO_STANDARD_LVCMOS18>;
+		};
+	};
+
+	pinctrl_i2c0_gpio: i2c0-gpio {
+		mux {
+			groups = "gpio0_14_grp", "gpio0_15_grp";
+			function = "gpio0";
+		};
+
+		conf {
+			groups = "gpio0_14_grp", "gpio0_15_grp";
+			slew-rate = <SLEW_RATE_SLOW>;
+			power-source = <IO_STANDARD_LVCMOS18>;
+		};
+	};
+
+	pinctrl_i2c1_default: i2c1-default {
+		mux {
+			groups = "i2c1_4_grp";
+			function = "i2c1";
+		};
+
+		conf {
+			groups = "i2c1_4_grp";
+			bias-pull-up;
+			slew-rate = <SLEW_RATE_SLOW>;
+			power-source = <IO_STANDARD_LVCMOS18>;
+		};
+	};
+
+	pinctrl_i2c1_gpio: i2c1-gpio {
+		mux {
+			groups = "gpio0_16_grp", "gpio0_17_grp";
+			function = "gpio0";
+		};
+
+		conf {
+			groups = "gpio0_16_grp", "gpio0_17_grp";
+			slew-rate = <SLEW_RATE_SLOW>;
+			power-source = <IO_STANDARD_LVCMOS18>;
+		};
+	};
+
+	pinctrl_uart0_default: uart0-default {
+		mux {
+			groups = "uart0_4_grp";
+			function = "uart0";
+		};
+
+		conf {
+			groups = "uart0_4_grp";
+			slew-rate = <SLEW_RATE_SLOW>;
+			power-source = <IO_STANDARD_LVCMOS18>;
+		};
+
+		conf-rx {
+			pins = "MIO18";
+			bias-high-impedance;
+		};
+
+		conf-tx {
+			pins = "MIO19";
+			bias-disable;
+		};
+	};
+
+	pinctrl_usb0_default: usb0-default {
+		mux {
+			groups = "usb0_0_grp";
+			function = "usb0";
+		};
+
+		conf {
+			groups = "usb0_0_grp";
+			slew-rate = <SLEW_RATE_SLOW>;
+			power-source = <IO_STANDARD_LVCMOS18>;
+		};
+
+		conf-rx {
+			pins = "MIO52", "MIO53", "MIO55";
+			bias-high-impedance;
+		};
+
+		conf-tx {
+			pins = "MIO54", "MIO56", "MIO57", "MIO58", "MIO59",
+			       "MIO60", "MIO61", "MIO62", "MIO63";
+			bias-disable;
+		};
+	};
+
+	pinctrl_gem3_default: gem3-default {
+		mux {
+			function = "ethernet3";
+			groups = "ethernet3_0_grp";
+		};
+
+		conf {
+			groups = "ethernet3_0_grp";
+			slew-rate = <SLEW_RATE_SLOW>;
+			power-source = <IO_STANDARD_LVCMOS18>;
+		};
+
+		conf-rx {
+			pins = "MIO70", "MIO71", "MIO72", "MIO73", "MIO74",
+									"MIO75";
+			bias-high-impedance;
+			low-power-disable;
+		};
+
+		conf-tx {
+			pins = "MIO64", "MIO65", "MIO66", "MIO67", "MIO68",
+									"MIO69";
+			bias-disable;
+			low-power-enable;
+		};
+
+		mux-mdio {
+			function = "mdio3";
+			groups = "mdio3_0_grp";
+		};
+
+		conf-mdio {
+			groups = "mdio3_0_grp";
+			slew-rate = <SLEW_RATE_SLOW>;
+			power-source = <IO_STANDARD_LVCMOS18>;
+			bias-disable;
+		};
+	};
+
+	pinctrl_sdhci1_default: sdhci1-default {
+		mux {
+			groups = "sdio1_0_grp";
+			function = "sdio1";
+		};
+
+		conf {
+			groups = "sdio1_0_grp";
+			slew-rate = <SLEW_RATE_SLOW>;
+			power-source = <IO_STANDARD_LVCMOS18>;
+			bias-disable;
+		};
+
+		mux-cd {
+			groups = "sdio1_cd_0_grp";
+			function = "sdio1_cd";
+		};
+
+		conf-cd {
+			groups = "sdio1_cd_0_grp";
+			bias-high-impedance;
+			bias-pull-up;
+			slew-rate = <SLEW_RATE_SLOW>;
+			power-source = <IO_STANDARD_LVCMOS18>;
+		};
+	};
+
+	pinctrl_gpio_default: gpio-default {
+		mux {
+			function = "gpio0";
+			groups = "gpio0_22_grp", "gpio0_23_grp";
+		};
+
+		conf {
+			groups = "gpio0_22_grp", "gpio0_23_grp";
+			slew-rate = <SLEW_RATE_SLOW>;
+			power-source = <IO_STANDARD_LVCMOS18>;
+		};
+
+		mux-msp {
+			function = "gpio0";
+			groups = "gpio0_13_grp", "gpio0_38_grp";
+		};
+
+		conf-msp {
+			groups = "gpio0_13_grp", "gpio0_38_grp";
+			slew-rate = <SLEW_RATE_SLOW>;
+			power-source = <IO_STANDARD_LVCMOS18>;
+		};
+
+		conf-pull-up {
+			pins = "MIO22";
+			bias-pull-up;
+		};
+
+		conf-pull-none {
+			pins = "MIO13", "MIO23", "MIO38";
+			bias-disable;
+		};
+	};
+};
+
 &psgtr {
 	status = "okay";
-	/* nc, sata, usb3, dp */
-	clocks = <&si5341 0 3>, <&si5341 0 2>, <&si5341 0 0>;
+	/* nc, dp, usb3, sata */
+	clocks = <&si5341 0 0>, <&si5341 0 2>, <&si5341 0 3>;
 	clock-names = "ref1", "ref2", "ref3";
 };
 
+&qspi {
+	status = "okay";
+	flash@0 {
+		compatible = "m25p80", "jedec,spi-nor"; /* 16MB + 16MB */
+		#address-cells = <1>;
+		#size-cells = <1>;
+		reg = <0x0>;
+		spi-tx-bus-width = <1>;
+		spi-rx-bus-width = <4>; /* FIXME also DUAL configuration possible */
+		spi-max-frequency = <108000000>; /* Based on DC1 spec */
+	};
+};
+
 &rtc {
 	status = "okay";
 };
@@ -565,24 +801,42 @@
 	ceva,p1-burst-params = /bits/ 8 <0x13 0x08 0x4A 0x06>;
 	ceva,p1-retry-params = /bits/ 16 <0x96A4 0x3FFC>;
 	phy-names = "sata-phy";
-	phys = <&psgtr 3 PHY_TYPE_SATA 1 1>;
+	phys = <&psgtr 3 PHY_TYPE_SATA 1 3>;
 };
 
 /* SD1 with level shifter */
 &sdhci1 {
 	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_sdhci1_default>;
+	disable-wp;
+	/*
+	 * This property should be removed for supporting UHS mode
+	 */
 	no-1-8-v;
 	xlnx,mio-bank = <1>;
 };
 
 &uart0 {
 	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart0_default>;
 };
 
 /* ULPI SMSC USB3320 */
 &usb0 {
 	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usb0_default>;
+	phy-names = "usb3-phy";
+	phys = <&psgtr 2 PHY_TYPE_USB3 0 2>;
+};
+
+&dwc3_0 {
+	status = "okay";
 	dr_mode = "host";
+	snps,usb3_lpm_capable;
+	maximum-speed = "super-speed";
 };
 
 &zynqmp_dpdma {
diff --git a/arch/arm64/boot/dts/xilinx/zynqmp.dtsi b/arch/arm64/boot/dts/xilinx/zynqmp.dtsi
index 28dccb891a53..74e66443e4ce 100644
--- a/arch/arm64/boot/dts/xilinx/zynqmp.dtsi
+++ b/arch/arm64/boot/dts/xilinx/zynqmp.dtsi
@@ -2,7 +2,7 @@
 /*
  * dts file for Xilinx ZynqMP
  *
- * (C) Copyright 2014 - 2019, Xilinx, Inc.
+ * (C) Copyright 2014 - 2021, Xilinx, Inc.
  *
  * Michal Simek <michal.simek@xilinx.com>
  *
@@ -156,21 +156,6 @@
 				mbox-names = "tx", "rx";
 			};
 
-			zynqmp_clk: clock-controller {
-				#clock-cells = <1>;
-				compatible = "xlnx,zynqmp-clk";
-				clocks = <&pss_ref_clk>,
-					 <&video_clk>,
-					 <&pss_alt_ref_clk>,
-					 <&aux_ref_clk>,
-					 <&gt_crx_ref_clk>;
-				clock-names = "pss_ref_clk",
-					      "video_clk",
-					      "pss_alt_ref_clk",
-					      "aux_ref_clk",
-					      "gt_crx_ref_clk";
-			};
-
 			nvmem_firmware {
 				compatible = "xlnx,zynqmp-nvmem-fw";
 				#address-cells = <1>;
@@ -193,6 +178,11 @@
 				compatible = "xlnx,zynqmp-reset";
 				#reset-cells = <1>;
 			};
+
+			pinctrl0: pinctrl {
+				compatible = "xlnx,zynqmp-pinctrl";
+				status = "disabled";
+			};
 		};
 	};
 
@@ -245,6 +235,7 @@
 
 		cci: cci@fd6e0000 {
 			compatible = "arm,cci-400";
+			status = "disabled";
 			reg = <0x0 0xfd6e0000 0x0 0x9000>;
 			ranges = <0x0 0x0 0xfd6e0000 0x10000>;
 			#address-cells = <1>;
@@ -630,6 +621,8 @@
 					<0x0 0x0 0x0 0x2 &pcie_intc 0x2>,
 					<0x0 0x0 0x0 0x3 &pcie_intc 0x3>,
 					<0x0 0x0 0x0 0x4 &pcie_intc 0x4>;
+			#stream-id-cells = <1>;
+			iommus = <&smmu 0x4d0>;
 			power-domains = <&zynqmp_firmware PD_PCIE>;
 			pcie_intc: legacy-interrupt-controller {
 				interrupt-controller;
@@ -670,7 +663,7 @@
 			interrupt-parent = <&gic>;
 			interrupts = <0 26 4>, <0 27 4>;
 			interrupt-names = "alarm", "sec";
-			calibration = <0x8000>;
+			calibration = <0x7FFF>;
 		};
 
 		sata: ahci@fd0c0000 {
@@ -680,6 +673,7 @@
 			interrupt-parent = <&gic>;
 			interrupts = <0 133 4>;
 			power-domains = <&zynqmp_firmware PD_SATA>;
+			resets = <&zynqmp_reset ZYNQMP_RESET_SATA>;
 			#stream-id-cells = <4>;
 			iommus = <&smmu 0x4c0>, <&smmu 0x4c1>,
 				 <&smmu 0x4c2>, <&smmu 0x4c3>;
@@ -792,7 +786,7 @@
 		};
 
 		uart0: serial@ff000000 {
-			compatible = "cdns,uart-r1p12", "xlnx,xuartps";
+			compatible = "xlnx,zynqmp-uart", "cdns,uart-r1p12";
 			status = "disabled";
 			interrupt-parent = <&gic>;
 			interrupts = <0 21 4>;
@@ -802,7 +796,7 @@
 		};
 
 		uart1: serial@ff010000 {
-			compatible = "cdns,uart-r1p12", "xlnx,xuartps";
+			compatible = "xlnx,zynqmp-uart", "cdns,uart-r1p12";
 			status = "disabled";
 			interrupt-parent = <&gic>;
 			interrupts = <0 22 4>;
@@ -811,24 +805,58 @@
 			power-domains = <&zynqmp_firmware PD_UART_1>;
 		};
 
-		usb0: usb@fe200000 {
-			compatible = "snps,dwc3";
+		usb0: usb@ff9d0000 {
+			#address-cells = <2>;
+			#size-cells = <2>;
 			status = "disabled";
-			interrupt-parent = <&gic>;
-			interrupts = <0 65 4>;
-			reg = <0x0 0xfe200000 0x0 0x40000>;
-			clock-names = "clk_xin", "clk_ahb";
+			compatible = "xlnx,zynqmp-dwc3";
+			reg = <0x0 0xff9d0000 0x0 0x100>;
+			clock-names = "bus_clk", "ref_clk";
 			power-domains = <&zynqmp_firmware PD_USB_0>;
+			resets = <&zynqmp_reset ZYNQMP_RESET_USB0_CORERESET>,
+				 <&zynqmp_reset ZYNQMP_RESET_USB0_HIBERRESET>,
+				 <&zynqmp_reset ZYNQMP_RESET_USB0_APB>;
+			reset-names = "usb_crst", "usb_hibrst", "usb_apbrst";
+			ranges;
+
+			dwc3_0: usb@fe200000 {
+				compatible = "snps,dwc3";
+				reg = <0x0 0xfe200000 0x0 0x40000>;
+				interrupt-parent = <&gic>;
+				interrupt-names = "dwc_usb3", "otg";
+				interrupts = <0 65 4>, <0 69 4>;
+				#stream-id-cells = <1>;
+				iommus = <&smmu 0x860>;
+				snps,quirk-frame-length-adjustment = <0x20>;
+				/* dma-coherent; */
+			};
 		};
 
-		usb1: usb@fe300000 {
-			compatible = "snps,dwc3";
+		usb1: usb@ff9e0000 {
+			#address-cells = <2>;
+			#size-cells = <2>;
 			status = "disabled";
-			interrupt-parent = <&gic>;
-			interrupts = <0 70 4>;
-			reg = <0x0 0xfe300000 0x0 0x40000>;
-			clock-names = "clk_xin", "clk_ahb";
+			compatible = "xlnx,zynqmp-dwc3";
+			reg = <0x0 0xff9e0000 0x0 0x100>;
+			clock-names = "bus_clk", "ref_clk";
 			power-domains = <&zynqmp_firmware PD_USB_1>;
+			resets = <&zynqmp_reset ZYNQMP_RESET_USB1_CORERESET>,
+				 <&zynqmp_reset ZYNQMP_RESET_USB1_HIBERRESET>,
+				 <&zynqmp_reset ZYNQMP_RESET_USB1_APB>;
+			reset-names = "usb_crst", "usb_hibrst", "usb_apbrst";
+			ranges;
+
+			dwc3_1: usb@fe300000 {
+				compatible = "snps,dwc3";
+				reg = <0x0 0xfe300000 0x0 0x40000>;
+				interrupt-parent = <&gic>;
+				interrupt-names = "dwc_usb3", "otg";
+				interrupts = <0 70 4>, <0 74 4>;
+				#stream-id-cells = <1>;
+				iommus = <&smmu 0x861>;
+				snps,quirk-frame-length-adjustment = <0x20>;
+				/* dma-coherent; */
+			};
 		};
 
 		watchdog0: watchdog@fd4d0000 {
@@ -837,7 +865,8 @@
 			interrupt-parent = <&gic>;
 			interrupts = <0 113 1>;
 			reg = <0x0 0xfd4d0000 0x0 0x1000>;
-			timeout-sec = <10>;
+			timeout-sec = <60>;
+			reset-on-timeout;
 		};
 
 		lpd_watchdog: watchdog@ff150000 {