summaryrefslogtreecommitdiff
path: root/arch/arm
diff options
context:
space:
mode:
authorLinus Walleij <linus.walleij@linaro.org>2013-09-10 11:19:55 +0200
committerLinus Walleij <linus.walleij@linaro.org>2013-09-27 14:15:07 +0200
commit8040dd09c2ca7e70daf84f040beb3ced9602fce5 (patch)
treec57e492d4d402a07c7585207a063545f50abc77d /arch/arm
parent272b98c6455f00884f0350f775c5342358ebb73f (diff)
ARM: ixp4xx: convert remaining users to use gpiolib
A few call sites inside mach-ixp4xx were still using the custom ixp4xx GPIO API with gpio_line_* accessors, convert all these to use the standard gpiolib functions instead. Also attempt to request and label all GPIOs before use. Move the GPIO requests to per-machine device_initcalls() so we are not dependent on the GPIO chip to be available at machine_init time. Cc: Imre Kaloz <kaloz@openwrt.org> Cc: Alexandre Courbot <acourbot@nvidia.com> Acked-by: Krzysztof Halasa <khc@pm.waw.pl> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Diffstat (limited to 'arch/arm')
-rw-r--r--arch/arm/mach-ixp4xx/dsmg600-setup.c65
-rw-r--r--arch/arm/mach-ixp4xx/ixdp425-setup.c8
-rw-r--r--arch/arm/mach-ixp4xx/nas100d-setup.c49
-rw-r--r--arch/arm/mach-ixp4xx/nslu2-setup.c17
4 files changed, 85 insertions, 54 deletions
diff --git a/arch/arm/mach-ixp4xx/dsmg600-setup.c b/arch/arm/mach-ixp4xx/dsmg600-setup.c
index 63de1b3fd06b..736dc692d540 100644
--- a/arch/arm/mach-ixp4xx/dsmg600-setup.c
+++ b/arch/arm/mach-ixp4xx/dsmg600-setup.c
@@ -26,6 +26,7 @@
#include <linux/reboot.h>
#include <linux/i2c.h>
#include <linux/i2c-gpio.h>
+#include <linux/gpio.h>
#include <mach/hardware.h>
@@ -161,11 +162,8 @@ static struct platform_device *dsmg600_devices[] __initdata = {
static void dsmg600_power_off(void)
{
- /* enable the pwr cntl gpio */
- gpio_line_config(DSMG600_PO_GPIO, IXP4XX_GPIO_OUT);
-
- /* poweroff */
- gpio_line_set(DSMG600_PO_GPIO, IXP4XX_GPIO_HIGH);
+ /* enable the pwr cntl and drive it high */
+ gpio_direction_output(DSMG600_PO_GPIO, 1);
}
/* This is used to make sure the power-button pusher is serious. The button
@@ -202,7 +200,7 @@ static void dsmg600_power_handler(unsigned long data)
ctrl_alt_del();
/* Change the state of the power LED to "blink" */
- gpio_line_set(DSMG600_LED_PWR_GPIO, IXP4XX_GPIO_LOW);
+ gpio_set_value(DSMG600_LED_PWR_GPIO, 0);
} else {
power_button_countdown = PBUTTON_HOLDDOWN_COUNT;
}
@@ -228,6 +226,40 @@ static void __init dsmg600_timer_init(void)
ixp4xx_timer_init();
}
+static int __init dsmg600_gpio_init(void)
+{
+ if (!machine_is_dsmg600())
+ return 0;
+
+ gpio_request(DSMG600_RB_GPIO, "reset button");
+ if (request_irq(gpio_to_irq(DSMG600_RB_GPIO), &dsmg600_reset_handler,
+ IRQF_DISABLED | IRQF_TRIGGER_LOW,
+ "DSM-G600 reset button", NULL) < 0) {
+
+ printk(KERN_DEBUG "Reset Button IRQ %d not available\n",
+ gpio_to_irq(DSMG600_RB_GPIO));
+ }
+
+ /*
+ * The power button on the D-Link DSM-G600 is on GPIO 15, but
+ * it cannot handle interrupts on that GPIO line. So we'll
+ * have to poll it with a kernel timer.
+ */
+
+ /* Make sure that the power button GPIO is set up as an input */
+ gpio_request(DSMG600_PB_GPIO, "power button");
+ gpio_direction_input(DSMG600_PB_GPIO);
+ /* Request poweroff GPIO line */
+ gpio_request(DSMG600_PO_GPIO, "power off button");
+
+ /* Set the initial value for the power button IRQ handler */
+ power_button_countdown = PBUTTON_HOLDDOWN_COUNT;
+
+ mod_timer(&dsmg600_power_timer, jiffies + msecs_to_jiffies(500));
+ return 0;
+}
+device_initcall(dsmg600_gpio_init);
+
static void __init dsmg600_init(void)
{
ixp4xx_sys_init();
@@ -251,27 +283,6 @@ static void __init dsmg600_init(void)
platform_add_devices(dsmg600_devices, ARRAY_SIZE(dsmg600_devices));
pm_power_off = dsmg600_power_off;
-
- if (request_irq(gpio_to_irq(DSMG600_RB_GPIO), &dsmg600_reset_handler,
- IRQF_DISABLED | IRQF_TRIGGER_LOW,
- "DSM-G600 reset button", NULL) < 0) {
-
- printk(KERN_DEBUG "Reset Button IRQ %d not available\n",
- gpio_to_irq(DSMG600_RB_GPIO));
- }
-
- /* The power button on the D-Link DSM-G600 is on GPIO 15, but
- * it cannot handle interrupts on that GPIO line. So we'll
- * have to poll it with a kernel timer.
- */
-
- /* Make sure that the power button GPIO is set up as an input */
- gpio_line_config(DSMG600_PB_GPIO, IXP4XX_GPIO_IN);
-
- /* Set the initial value for the power button IRQ handler */
- power_button_countdown = PBUTTON_HOLDDOWN_COUNT;
-
- mod_timer(&dsmg600_power_timer, jiffies + msecs_to_jiffies(500));
}
MACHINE_START(DSMG600, "D-Link DSM-G600 RevA")
diff --git a/arch/arm/mach-ixp4xx/ixdp425-setup.c b/arch/arm/mach-ixp4xx/ixdp425-setup.c
index 22d688b7d513..e7b8befa8729 100644
--- a/arch/arm/mach-ixp4xx/ixdp425-setup.c
+++ b/arch/arm/mach-ixp4xx/ixdp425-setup.c
@@ -20,6 +20,7 @@
#include <linux/mtd/nand.h>
#include <linux/mtd/partitions.h>
#include <linux/delay.h>
+#include <linux/gpio.h>
#include <asm/types.h>
#include <asm/setup.h>
#include <asm/memory.h>
@@ -80,10 +81,10 @@ ixdp425_flash_nand_cmd_ctrl(struct mtd_info *mtd, int cmd, unsigned int ctrl)
if (ctrl & NAND_CTRL_CHANGE) {
if (ctrl & NAND_NCE) {
- gpio_line_set(IXDP425_NAND_NCE_PIN, IXP4XX_GPIO_LOW);
+ gpio_set_value(IXDP425_NAND_NCE_PIN, 0);
udelay(5);
} else
- gpio_line_set(IXDP425_NAND_NCE_PIN, IXP4XX_GPIO_HIGH);
+ gpio_set_value(IXDP425_NAND_NCE_PIN, 1);
offset = (ctrl & NAND_CLE) ? IXDP425_NAND_CMD_BYTE : 0;
offset |= (ctrl & NAND_ALE) ? IXDP425_NAND_ADDR_BYTE : 0;
@@ -227,7 +228,8 @@ static void __init ixdp425_init(void)
ixdp425_flash_nand_resource.start = IXP4XX_EXP_BUS_BASE(3),
ixdp425_flash_nand_resource.end = IXP4XX_EXP_BUS_BASE(3) + 0x10 - 1;
- gpio_line_config(IXDP425_NAND_NCE_PIN, IXP4XX_GPIO_OUT);
+ gpio_request(IXDP425_NAND_NCE_PIN, "NAND NCE pin");
+ gpio_direction_output(IXDP425_NAND_NCE_PIN, 0);
/* Configure expansion bus for NAND Flash */
*IXP4XX_EXP_CS3 = IXP4XX_EXP_BUS_CS_EN |
diff --git a/arch/arm/mach-ixp4xx/nas100d-setup.c b/arch/arm/mach-ixp4xx/nas100d-setup.c
index ed667ce9f576..507cb5233537 100644
--- a/arch/arm/mach-ixp4xx/nas100d-setup.c
+++ b/arch/arm/mach-ixp4xx/nas100d-setup.c
@@ -184,11 +184,8 @@ static void nas100d_power_off(void)
{
/* This causes the box to drop the power and go dead. */
- /* enable the pwr cntl gpio */
- gpio_line_config(NAS100D_PO_GPIO, IXP4XX_GPIO_OUT);
-
- /* do the deed */
- gpio_line_set(NAS100D_PO_GPIO, IXP4XX_GPIO_HIGH);
+ /* enable the pwr cntl gpio and assert power off */
+ gpio_direction_output(NAS100D_PO_GPIO, 1);
}
/* This is used to make sure the power-button pusher is serious. The button
@@ -225,7 +222,7 @@ static void nas100d_power_handler(unsigned long data)
ctrl_alt_del();
/* Change the state of the power LED to "blink" */
- gpio_line_set(NAS100D_LED_PWR_GPIO, IXP4XX_GPIO_LOW);
+ gpio_set_value(NAS100D_LED_PWR_GPIO, 0);
} else {
power_button_countdown = PBUTTON_HOLDDOWN_COUNT;
}
@@ -242,6 +239,33 @@ static irqreturn_t nas100d_reset_handler(int irq, void *dev_id)
return IRQ_HANDLED;
}
+static int __init nas100d_gpio_init(void)
+{
+ if (!machine_is_nas100d())
+ return 0;
+
+ /*
+ * The power button on the Iomega NAS100d is on GPIO 14, but
+ * it cannot handle interrupts on that GPIO line. So we'll
+ * have to poll it with a kernel timer.
+ */
+
+ /* Request the power off GPIO */
+ gpio_request(NAS100D_PO_GPIO, "power off");
+
+ /* Make sure that the power button GPIO is set up as an input */
+ gpio_request(NAS100D_PB_GPIO, "power button");
+ gpio_direction_input(NAS100D_PB_GPIO);
+
+ /* Set the initial value for the power button IRQ handler */
+ power_button_countdown = PBUTTON_HOLDDOWN_COUNT;
+
+ mod_timer(&nas100d_power_timer, jiffies + msecs_to_jiffies(500));
+
+ return 0;
+}
+device_initcall(nas100d_gpio_init);
+
static void __init nas100d_init(void)
{
uint8_t __iomem *f;
@@ -278,19 +302,6 @@ static void __init nas100d_init(void)
gpio_to_irq(NAS100D_RB_GPIO));
}
- /* The power button on the Iomega NAS100d is on GPIO 14, but
- * it cannot handle interrupts on that GPIO line. So we'll
- * have to poll it with a kernel timer.
- */
-
- /* Make sure that the power button GPIO is set up as an input */
- gpio_line_config(NAS100D_PB_GPIO, IXP4XX_GPIO_IN);
-
- /* Set the initial value for the power button IRQ handler */
- power_button_countdown = PBUTTON_HOLDDOWN_COUNT;
-
- mod_timer(&nas100d_power_timer, jiffies + msecs_to_jiffies(500));
-
/*
* Map in a portion of the flash and read the MAC address.
* Since it is stored in BE in the flash itself, we need to
diff --git a/arch/arm/mach-ixp4xx/nslu2-setup.c b/arch/arm/mach-ixp4xx/nslu2-setup.c
index 7e55236c26ea..ba5f1cda2a9d 100644
--- a/arch/arm/mach-ixp4xx/nslu2-setup.c
+++ b/arch/arm/mach-ixp4xx/nslu2-setup.c
@@ -197,11 +197,8 @@ static void nslu2_power_off(void)
{
/* This causes the box to drop the power and go dead. */
- /* enable the pwr cntl gpio */
- gpio_line_config(NSLU2_PO_GPIO, IXP4XX_GPIO_OUT);
-
- /* do the deed */
- gpio_line_set(NSLU2_PO_GPIO, IXP4XX_GPIO_HIGH);
+ /* enable the pwr cntl gpio and assert power off */
+ gpio_direction_output(NSLU2_PO_GPIO, 1);
}
static irqreturn_t nslu2_power_handler(int irq, void *dev_id)
@@ -223,6 +220,16 @@ static irqreturn_t nslu2_reset_handler(int irq, void *dev_id)
return IRQ_HANDLED;
}
+static int __init nslu2_gpio_init(void)
+{
+ if (!machine_is_nslu2())
+ return 0;
+
+ /* Request the power off GPIO */
+ return gpio_request(NSLU2_PO_GPIO, "power off");
+}
+device_initcall(nslu2_gpio_init);
+
static void __init nslu2_timer_init(void)
{
/* The xtal on this machine is non-standard. */