ata: move sata_link_{debounce,resume}() to libata-sata.c

* move sata_link_{debounce,resume}() to libata-sata.c

* add static inline for CONFIG_SATA_HOST=n case (only one,
  for sata_link_resume() is needed)

Code size savings on m68k arch using (modified) atari_defconfig:

   text    data     bss     dec     hex filename
before:
  32816     572      40   33428    8294 drivers/ata/libata-core.o
after:
  32724     572      40   33336    8238 drivers/ata/libata-core.o

Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>

1 files changed, 0 insertions, 138 deletions

diff --git a/drivers/ata/libata-core.c b/drivers/ata/libata-core.c
index 13214ebd0e5c..4ca81ef7c8bd 100644
--- a/drivers/ata/libata-core.c
+++ b/drivers/ata/libata-core.c
@@ -3486,144 +3486,6 @@ int ata_wait_after_reset(struct ata_link *link, unsigned long deadline,
 EXPORT_SYMBOL_GPL(ata_wait_after_reset);
 
 /**
- *	sata_link_debounce - debounce SATA phy status
- *	@link: ATA link to debounce SATA phy status for
- *	@params: timing parameters { interval, duration, timeout } in msec
- *	@deadline: deadline jiffies for the operation
- *
- *	Make sure SStatus of @link reaches stable state, determined by
- *	holding the same value where DET is not 1 for @duration polled
- *	every @interval, before @timeout.  Timeout constraints the
- *	beginning of the stable state.  Because DET gets stuck at 1 on
- *	some controllers after hot unplugging, this functions waits
- *	until timeout then returns 0 if DET is stable at 1.
- *
- *	@timeout is further limited by @deadline.  The sooner of the
- *	two is used.
- *
- *	LOCKING:
- *	Kernel thread context (may sleep)
- *
- *	RETURNS:
- *	0 on success, -errno on failure.
- */
-int sata_link_debounce(struct ata_link *link, const unsigned long *params,
-		       unsigned long deadline)
-{
-	unsigned long interval = params[0];
-	unsigned long duration = params[1];
-	unsigned long last_jiffies, t;
-	u32 last, cur;
-	int rc;
-
-	t = ata_deadline(jiffies, params[2]);
-	if (time_before(t, deadline))
-		deadline = t;
-
-	if ((rc = sata_scr_read(link, SCR_STATUS, &cur)))
-		return rc;
-	cur &= 0xf;
-
-	last = cur;
-	last_jiffies = jiffies;
-
-	while (1) {
-		ata_msleep(link->ap, interval);
-		if ((rc = sata_scr_read(link, SCR_STATUS, &cur)))
-			return rc;
-		cur &= 0xf;
-
-		/* DET stable? */
-		if (cur == last) {
-			if (cur == 1 && time_before(jiffies, deadline))
-				continue;
-			if (time_after(jiffies,
-				       ata_deadline(last_jiffies, duration)))
-				return 0;
-			continue;
-		}
-
-		/* unstable, start over */
-		last = cur;
-		last_jiffies = jiffies;
-
-		/* Check deadline.  If debouncing failed, return
-		 * -EPIPE to tell upper layer to lower link speed.
-		 */
-		if (time_after(jiffies, deadline))
-			return -EPIPE;
-	}
-}
-EXPORT_SYMBOL_GPL(sata_link_debounce);
-
-/**
- *	sata_link_resume - resume SATA link
- *	@link: ATA link to resume SATA
- *	@params: timing parameters { interval, duration, timeout } in msec
- *	@deadline: deadline jiffies for the operation
- *
- *	Resume SATA phy @link and debounce it.
- *
- *	LOCKING:
- *	Kernel thread context (may sleep)
- *
- *	RETURNS:
- *	0 on success, -errno on failure.
- */
-int sata_link_resume(struct ata_link *link, const unsigned long *params,
-		     unsigned long deadline)
-{
-	int tries = ATA_LINK_RESUME_TRIES;
-	u32 scontrol, serror;
-	int rc;
-
-	if ((rc = sata_scr_read(link, SCR_CONTROL, &scontrol)))
-		return rc;
-
-	/*
-	 * Writes to SControl sometimes get ignored under certain
-	 * controllers (ata_piix SIDPR).  Make sure DET actually is
-	 * cleared.
-	 */
-	do {
-		scontrol = (scontrol & 0x0f0) | 0x300;
-		if ((rc = sata_scr_write(link, SCR_CONTROL, scontrol)))
-			return rc;
-		/*
-		 * Some PHYs react badly if SStatus is pounded
-		 * immediately after resuming.  Delay 200ms before
-		 * debouncing.
-		 */
-		if (!(link->flags & ATA_LFLAG_NO_DB_DELAY))
-			ata_msleep(link->ap, 200);
-
-		/* is SControl restored correctly? */
-		if ((rc = sata_scr_read(link, SCR_CONTROL, &scontrol)))
-			return rc;
-	} while ((scontrol & 0xf0f) != 0x300 && --tries);
-
-	if ((scontrol & 0xf0f) != 0x300) {
-		ata_link_warn(link, "failed to resume link (SControl %X)\n",
-			     scontrol);
-		return 0;
-	}
-
-	if (tries < ATA_LINK_RESUME_TRIES)
-		ata_link_warn(link, "link resume succeeded after %d retries\n",
-			      ATA_LINK_RESUME_TRIES - tries);
-
-	if ((rc = sata_link_debounce(link, params, deadline)))
-		return rc;
-
-	/* clear SError, some PHYs require this even for SRST to work */
-	if (!(rc = sata_scr_read(link, SCR_ERROR, &serror)))
-		rc = sata_scr_write(link, SCR_ERROR, serror);
-
-	return rc != -EINVAL ? rc : 0;
-}
-EXPORT_SYMBOL_GPL(sata_link_resume);
-
-/**
  *	ata_std_prereset - prepare for reset
  *	@link: ATA link to be reset
  *	@deadline: deadline jiffies for the operation