Merge tag 'iio-for-4.13b' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-next

Jonathan writes:

Second set of IIO new device support, features and cleanups for the 4.13 cycle.

A few reverts here. One was a general failure to notice a device was already
supported by another driver.  The second is due to a review comment pointing
out that the original patch was a bad idea and would break existing systems.

Reverts
* bma180
  - Revert addition of support for the BMA250E it is already supported by
    the bmc150-accel and better supported at that. Oops.
* hi8435
  - The fix for cleanup of the reset gpio stuff isn't a good way to go.  It
    breaks systems where an inverting level convertor is used.  The right fix
    is to make the original devicetree correct - even if it involves patching
    the devicetree in kernel.

New Device Support
* stm32-adc
  - STM32H7 support and bindings.

Features
* core
  - add a hardware triggered operating mode for systems in which the actual
    trigger is never seen by the kernel.  This is typically only used when
    a device 'can' use other triggers, but if a particular magic one is
    enabled the interrupt is effectively handled in hardware and we never see
    it.
* st-lsm6dsx
  - support active low interrupts.
* stm32-adc
  - Make the core adc clock optional as not all hardware supported requires it.
  - Make the bus clock optional in the per instance driver as it may be shared
    by all instances of the ADC and is handled by the core.
  - Rework to have a data structure representing the device type specific
    elements.
* stm32-trigger (and counter)
  - Use the INDIO_HARDWARE_TRIGGERED_MODE where appropriate.
  - Add an attribute to configure device modes for quadrature counting etc.

Clean ups and minor fixes
* IIO core.
  - use __sysfs_match_string() helper rather than open coding the same.
* ad7791
  - use sysfs_match_string() helper rather than open coding the same.
* aspeed-adc
  - handle return value of clk_prepare_enable
* cpcap
  - Fix default register values and ensure the battery thermistor is enabled
    correctly.
  - Fix the reported die temperature where we can - docs are lacking.
  - Remove the hung interrupt quirk as no longer happens due to fix in the
    mfd driver.
* hi8435
  - Remove &s from hi8435_info definition as unneeded and inconsistent.
* hid-sensor-trgger
  - Add kconfig depends on IIO_BUFFER (fixes patch in previous series)
* ina2xx
  - Make the use of iio_info_mask* elements consistent for all channels.
    This doesn't have any visible effect, but acts as clear documentation of
    which channels various resulting attributes apply to.
* lpc32xx
  - handle the return value of clk_prepare_enable.
* meson-saradc
  - NULL instead of 0 for pointer.
* mma9551
  - use NULL for GPIO connection ID to aid implementation fo ACPI support.
    Here the connection ID doesn't actually tell us anything and it is much
    easier to deal with the driver if it's not there.
* mpu6050
  - Fix lock issues through use of a local mux.
  - Replace sprintf with scnprintf as appropriate.
  - Check whoami against all known values.  This allows for a small number of
    boards where we are really fishing for the part not being present at all.
    It is unfortunately common to have undescribed changes to use newer chips.
    We paper over this but just emitting a warning for those cases as long as
    we know about.
* mxs-lradc
  - Fix some non static warnings.
* rcar-adc
  - Part of making the naming for this part consistent across the kernel.
* st_accel
  - drop some spi_device_id entries for variants with no SPI support
* st_magn
  - drop some spi_device_id entries for variants with no SPI support.
* sx9500
  - Use devm_gpiod_get instead of indexed value with an index of 0 on all
    occasions.
* twl4030
  - Drop unused twl4030_get_madc_conversion as callers removed now throughout
    kernel.
  - Unexport twl4030_madc_conversion() as no used only within this driver.
  - Drop twl4030_madc_user_params as not used now.
  - Drop twl4030_madc_request.func_cb as not used now.
  - Fold the twl4030-madc.h header into the driver as no longer used anywhere
    else in the kernel.
* xilinx
  - Handle the return value of clk_prepare_enable

26 files changed, 1585 insertions, 415 deletions

diff --git a/drivers/iio/accel/bma180.c b/drivers/iio/accel/bma180.c
index 17b7953f2502..efc67739c28f 100644
--- a/drivers/iio/accel/bma180.c
+++ b/drivers/iio/accel/bma180.c
@@ -14,7 +14,6 @@
  * BMA250: 7-bit I2C slave address 0x18 or 0x19
  */
 
-#include <linux/acpi.h>
 #include <linux/module.h>
 #include <linux/i2c.h>
 #include <linux/interrupt.h>
@@ -37,7 +36,6 @@
 enum chip_ids {
 	BMA180,
 	BMA250,
-	BMA250E,
 };
 
 struct bma180_data;
@@ -57,7 +55,6 @@ struct bma180_part_info {
 	u8 power_reg, power_mask, lowpower_val;
 	u8 int_enable_reg, int_enable_mask;
 	u8 softreset_reg;
-	u8 chip_id;
 
 	int (*chip_config)(struct bma180_data *data);
 	void (*chip_disable)(struct bma180_data *data);
@@ -115,8 +112,6 @@ struct bma180_part_info {
 #define BMA250_INT1_DATA_MASK	BIT(0)
 #define BMA250_INT_RESET_MASK	BIT(7) /* Reset pending interrupts */
 
-#define BMA250E_CHIP_ID		0xf9
-
 struct bma180_data {
 	struct i2c_client *client;
 	struct iio_trigger *trig;
@@ -314,7 +309,7 @@ static int bma180_chip_init(struct bma180_data *data)
 
 	if (ret < 0)
 		return ret;
-	if (ret != data->part_info->chip_id)
+	if (ret != BMA180_ID_REG_VAL)
 		return -ENODEV;
 
 	ret = bma180_soft_reset(data);
@@ -637,7 +632,6 @@ static const struct bma180_part_info bma180_part_info[] = {
 		BMA180_TCO_Z, BMA180_MODE_CONFIG, BMA180_LOW_POWER,
 		BMA180_CTRL_REG3, BMA180_NEW_DATA_INT,
 		BMA180_RESET,
-		BMA180_CHIP_ID,
 		bma180_chip_config,
 		bma180_chip_disable,
 	},
@@ -652,22 +646,6 @@ static const struct bma180_part_info bma180_part_info[] = {
 		BMA250_POWER_REG, BMA250_LOWPOWER_MASK, 1,
 		BMA250_INT_ENABLE_REG, BMA250_DATA_INTEN_MASK,
 		BMA250_RESET_REG,
-		BMA180_CHIP_ID,
-		bma250_chip_config,
-		bma250_chip_disable,
-	},
-	[BMA250E] = {
-		bma250_channels, ARRAY_SIZE(bma250_channels),
-		bma250_scale_table, ARRAY_SIZE(bma250_scale_table),
-		bma250_bw_table, ARRAY_SIZE(bma250_bw_table),
-		BMA250_INT_RESET_REG, BMA250_INT_RESET_MASK,
-		BMA250_POWER_REG, BMA250_SUSPEND_MASK,
-		BMA250_BW_REG, BMA250_BW_MASK,
-		BMA250_RANGE_REG, BMA250_RANGE_MASK,
-		BMA250_POWER_REG, BMA250_LOWPOWER_MASK, 1,
-		BMA250_INT_ENABLE_REG, BMA250_DATA_INTEN_MASK,
-		BMA250_RESET_REG,
-		BMA250E_CHIP_ID,
 		bma250_chip_config,
 		bma250_chip_disable,
 	},
@@ -728,8 +706,6 @@ static const struct iio_trigger_ops bma180_trigger_ops = {
 static int bma180_probe(struct i2c_client *client,
 		const struct i2c_device_id *id)
 {
-	struct device *dev = &client->dev;
-	const struct acpi_device_id *acpi_id;
 	struct bma180_data *data;
 	struct iio_dev *indio_dev;
 	enum chip_ids chip;
@@ -742,17 +718,10 @@ static int bma180_probe(struct i2c_client *client,
 	data = iio_priv(indio_dev);
 	i2c_set_clientdata(client, indio_dev);
 	data->client = client;
-	if (dev->of_node) {
+	if (client->dev.of_node)
 		chip = (enum chip_ids)of_device_get_match_data(&client->dev);
-	} else if (id) {
+	else
 		chip = id->driver_data;
-	} else {
-		acpi_id = acpi_match_device(dev->driver->acpi_match_table, dev);
-		if (!acpi_id)
-			return -ENODEV;
-
-		chip = acpi_id->driver_data;
-	}
 	data->part_info = &bma180_part_info[chip];
 
 	ret = data->part_info->chip_config(data);
@@ -873,16 +842,9 @@ static SIMPLE_DEV_PM_OPS(bma180_pm_ops, bma180_suspend, bma180_resume);
 #define BMA180_PM_OPS NULL
 #endif
 
-static const struct acpi_device_id bma180_acpi_match[] = {
-	{ "BMA250E", BMA250E },
-	{ }
-};
-MODULE_DEVICE_TABLE(acpi, bma180_acpi_match);
-
 static struct i2c_device_id bma180_ids[] = {
 	{ "bma180", BMA180 },
 	{ "bma250", BMA250 },
-	{ "bma250e", BMA250E },
 	{ }
 };
 
@@ -904,7 +866,6 @@ MODULE_DEVICE_TABLE(of, bma180_of_match);
 static struct i2c_driver bma180_driver = {
 	.driver = {
 		.name	= "bma180",
-		.acpi_match_table = ACPI_PTR(bma180_acpi_match),
 		.pm	= BMA180_PM_OPS,
 		.of_match_table = bma180_of_match,
 	},
diff --git a/drivers/iio/accel/mma9551.c b/drivers/iio/accel/mma9551.c
index bf2704435629..1f53f08476f5 100644
--- a/drivers/iio/accel/mma9551.c
+++ b/drivers/iio/accel/mma9551.c
@@ -27,7 +27,6 @@
 
 #define MMA9551_DRV_NAME		"mma9551"
 #define MMA9551_IRQ_NAME		"mma9551_event"
-#define MMA9551_GPIO_NAME		"mma9551_int"
 #define MMA9551_GPIO_COUNT		4
 
 /* Tilt application (inclination in IIO terms). */
@@ -418,8 +417,7 @@ static int mma9551_gpio_probe(struct iio_dev *indio_dev)
 	struct device *dev = &data->client->dev;
 
 	for (i = 0; i < MMA9551_GPIO_COUNT; i++) {
-		gpio = devm_gpiod_get_index(dev, MMA9551_GPIO_NAME, i,
-					    GPIOD_IN);
+		gpio = devm_gpiod_get_index(dev, NULL, i, GPIOD_IN);
 		if (IS_ERR(gpio)) {
 			dev_err(dev, "acpi gpio get index failed\n");
 			return PTR_ERR(gpio);
diff --git a/drivers/iio/accel/st_accel_spi.c b/drivers/iio/accel/st_accel_spi.c
index 29a15f27a51b..1a867f5563a4 100644
--- a/drivers/iio/accel/st_accel_spi.c
+++ b/drivers/iio/accel/st_accel_spi.c
@@ -47,15 +47,11 @@ static int st_accel_spi_remove(struct spi_device *spi)
 }
 
 static const struct spi_device_id st_accel_id_table[] = {
-	{ LSM303DLH_ACCEL_DEV_NAME },
-	{ LSM303DLHC_ACCEL_DEV_NAME },
 	{ LIS3DH_ACCEL_DEV_NAME },
 	{ LSM330D_ACCEL_DEV_NAME },
 	{ LSM330DL_ACCEL_DEV_NAME },
 	{ LSM330DLC_ACCEL_DEV_NAME },
 	{ LIS331DLH_ACCEL_DEV_NAME },
-	{ LSM303DL_ACCEL_DEV_NAME },
-	{ LSM303DLM_ACCEL_DEV_NAME },
 	{ LSM330_ACCEL_DEV_NAME },
 	{ LSM303AGR_ACCEL_DEV_NAME },
 	{ LIS2DH12_ACCEL_DEV_NAME },
diff --git a/drivers/iio/adc/ad7791.c b/drivers/iio/adc/ad7791.c
index 1817ebf5ad84..34e353c43ac8 100644
--- a/drivers/iio/adc/ad7791.c
+++ b/drivers/iio/adc/ad7791.c
@@ -272,11 +272,9 @@ static ssize_t ad7791_write_frequency(struct device *dev,
 	struct ad7791_state *st = iio_priv(indio_dev);
 	int i, ret;
 
-	for (i = 0; i < ARRAY_SIZE(ad7791_sample_freq_avail); i++)
-		if (sysfs_streq(ad7791_sample_freq_avail[i], buf))
-			break;
-	if (i == ARRAY_SIZE(ad7791_sample_freq_avail))
-		return -EINVAL;
+	i = sysfs_match_string(ad7791_sample_freq_avail, buf);
+	if (i < 0)
+		return i;
 
 	ret = iio_device_claim_direct_mode(indio_dev);
 	if (ret)
diff --git a/drivers/iio/adc/aspeed_adc.c b/drivers/iio/adc/aspeed_adc.c
index 62670cbfa2bb..e0ea411a0b2d 100644
--- a/drivers/iio/adc/aspeed_adc.c
+++ b/drivers/iio/adc/aspeed_adc.c
@@ -212,7 +212,10 @@ static int aspeed_adc_probe(struct platform_device *pdev)
 	}
 
 	/* Start all channels in normal mode. */
-	clk_prepare_enable(data->clk_scaler->clk);
+	ret = clk_prepare_enable(data->clk_scaler->clk);
+	if (ret)
+		goto clk_enable_error;
+
 	adc_engine_control_reg_val = GENMASK(31, 16) |
 		ASPEED_OPERATION_MODE_NORMAL | ASPEED_ENGINE_ENABLE;
 	writel(adc_engine_control_reg_val,
@@ -236,6 +239,7 @@ iio_register_error:
 	writel(ASPEED_OPERATION_MODE_POWER_DOWN,
 		data->base + ASPEED_REG_ENGINE_CONTROL);
 	clk_disable_unprepare(data->clk_scaler->clk);
+clk_enable_error:
 	clk_hw_unregister_divider(data->clk_scaler);
 
 scaler_error:
diff --git a/drivers/iio/adc/cpcap-adc.c b/drivers/iio/adc/cpcap-adc.c
index 62d37f8725b8..6e419d5a7c14 100644
--- a/drivers/iio/adc/cpcap-adc.c
+++ b/drivers/iio/adc/cpcap-adc.c
@@ -52,6 +52,10 @@
 #define CPCAP_BIT_RAND0			BIT(1)	/* Set with CAL_MODE */
 #define CPCAP_BIT_ADEN			BIT(0)	/* Currently unused */
 
+#define CPCAP_REG_ADCC1_DEFAULTS	(CPCAP_BIT_ADEN_AUTO_CLR | \
+					 CPCAP_BIT_ADC_CLK_SEL0 |  \
+					 CPCAP_BIT_RAND1)
+
 /* Register CPCAP_REG_ADCC2 bits */
 #define CPCAP_BIT_CAL_FACTOR_ENABLE	BIT(15)	/* Currently unused */
 #define CPCAP_BIT_BATDETB_EN		BIT(14)	/* Currently unused */
@@ -62,7 +66,7 @@
 #define CPCAP_BIT_ADC_PS_FACTOR0	BIT(9)
 #define CPCAP_BIT_AD4_SELECT		BIT(8)	/* Currently unused */
 #define CPCAP_BIT_ADC_BUSY		BIT(7)	/* Currently unused */
-#define CPCAP_BIT_THERMBIAS_EN		BIT(6)	/* Currently unused */
+#define CPCAP_BIT_THERMBIAS_EN		BIT(6)	/* Bias for AD0_BATTDETB */
 #define CPCAP_BIT_ADTRIG_DIS		BIT(5)	/* Disable interrupt */
 #define CPCAP_BIT_LIADC			BIT(4)	/* Currently unused */
 #define CPCAP_BIT_TS_REFEN		BIT(3)	/* Currently unused */
@@ -70,6 +74,12 @@
 #define CPCAP_BIT_TS_M1			BIT(1)	/* Currently unused */
 #define CPCAP_BIT_TS_M0			BIT(0)	/* Currently unused */
 
+#define CPCAP_REG_ADCC2_DEFAULTS	(CPCAP_BIT_AD4_SELECT | \
+					 CPCAP_BIT_ADTRIG_DIS | \
+					 CPCAP_BIT_LIADC | \
+					 CPCAP_BIT_TS_M2 | \
+					 CPCAP_BIT_TS_M1)
+
 #define CPCAP_MAX_TEMP_LVL		27
 #define CPCAP_FOUR_POINT_TWO_ADC	801
 #define ST_ADC_CAL_CHRGI_HIGH_THRESHOLD	530
@@ -78,7 +88,7 @@
 #define ST_ADC_CAL_BATTI_LOW_THRESHOLD	494
 #define ST_ADC_CALIBRATE_DIFF_THRESHOLD	3
 
-#define CPCAP_ADC_MAX_RETRIES		5	/* Calibration and quirk */
+#define CPCAP_ADC_MAX_RETRIES		5	/* Calibration */
 
 /**
  * struct cpcap_adc_ato - timing settings for cpcap adc
@@ -124,10 +134,10 @@ struct cpcap_adc {
  */
 enum cpcap_adc_channel {
 	/* Bank0 channels */
-	CPCAP_ADC_AD0_BATTDETB,	/* Battery detection */
+	CPCAP_ADC_AD0,		/* Battery temperature */
 	CPCAP_ADC_BATTP,	/* Battery voltage */
 	CPCAP_ADC_VBUS,		/* USB VBUS voltage */
-	CPCAP_ADC_AD3,		/* Battery temperature when charging */
+	CPCAP_ADC_AD3,		/* Die temperature when charging */
 	CPCAP_ADC_BPLUS_AD4,	/* Another battery or system voltage */
 	CPCAP_ADC_CHG_ISENSE,	/* Calibrated charge current */
 	CPCAP_ADC_BATTI,	/* Calibrated system current */
@@ -217,7 +227,7 @@ struct cpcap_adc_request {
 /* Phasing table for channels. Note that channels 16 & 17 use BATTP and BATTI */
 static const struct cpcap_adc_phasing_tbl bank_phasing[] = {
 	/* Bank0 */
-	[CPCAP_ADC_AD0_BATTDETB] = {0, 0x80, 0x80,    0, 1023},
+	[CPCAP_ADC_AD0] =          {0, 0x80, 0x80,    0, 1023},
 	[CPCAP_ADC_BATTP] =        {0, 0x80, 0x80,    0, 1023},
 	[CPCAP_ADC_VBUS] =         {0, 0x80, 0x80,    0, 1023},
 	[CPCAP_ADC_AD3] =          {0, 0x80, 0x80,    0, 1023},
@@ -243,7 +253,7 @@ static const struct cpcap_adc_phasing_tbl bank_phasing[] = {
  */
 static struct cpcap_adc_conversion_tbl bank_conversion[] = {
 	/* Bank0 */
-	[CPCAP_ADC_AD0_BATTDETB] = {
+	[CPCAP_ADC_AD0] = {
 		IIO_CHAN_INFO_PROCESSED,    0,    0, 0,     1,    1,
 	},
 	[CPCAP_ADC_BATTP] = {
@@ -541,6 +551,15 @@ static void cpcap_adc_setup_bank(struct cpcap_adc *ddata,
 		return;
 
 	switch (req->channel) {
+	case CPCAP_ADC_AD0:
+		value2 |= CPCAP_BIT_THERMBIAS_EN;
+		error = regmap_update_bits(ddata->reg, CPCAP_REG_ADCC2,
+					   CPCAP_BIT_THERMBIAS_EN,
+					   value2);
+		if (error)
+			return;
+		usleep_range(800, 1000);
+		break;
 	case CPCAP_ADC_AD8 ... CPCAP_ADC_TSY2_AD15:
 		value1 |= CPCAP_BIT_AD_SEL1;
 		break;
@@ -583,7 +602,8 @@ static void cpcap_adc_setup_bank(struct cpcap_adc *ddata,
 	error = regmap_update_bits(ddata->reg, CPCAP_REG_ADCC2,
 				   CPCAP_BIT_ATOX_PS_FACTOR |
 				   CPCAP_BIT_ADC_PS_FACTOR1 |
-				   CPCAP_BIT_ADC_PS_FACTOR0,
+				   CPCAP_BIT_ADC_PS_FACTOR0 |
+				   CPCAP_BIT_THERMBIAS_EN,
 				   value2);
 	if (error)
 		return;
@@ -614,27 +634,6 @@ static void cpcap_adc_setup_bank(struct cpcap_adc *ddata,
 	}
 }
 
-/*
- * Occasionally the ADC does not seem to start and there will be no
- * interrupt. Let's re-init interrupt to prevent the ADC from hanging
- * for the next request. It is unclear why this happens, but the next
- * request will usually work after doing this.
- */
-static void cpcap_adc_quirk_reset_lost_irq(struct cpcap_adc *ddata)
-{
-	int error;
-
-	dev_info(ddata->dev, "lost ADC irq, attempting to reinit\n");
-	disable_irq(ddata->irq);
-	error = regmap_update_bits(ddata->reg, CPCAP_REG_ADCC2,
-				   CPCAP_BIT_ADTRIG_DIS,
-				   CPCAP_BIT_ADTRIG_DIS);
-	if (error)
-		dev_warn(ddata->dev, "%s reset failed: %i\n",
-			 __func__, error);
-	enable_irq(ddata->irq);
-}
-
 static int cpcap_adc_start_bank(struct cpcap_adc *ddata,
 				struct cpcap_adc_request *req)
 {
@@ -652,7 +651,6 @@ static int cpcap_adc_start_bank(struct cpcap_adc *ddata,
 			return 0;
 
 		if (error == 0) {
-			cpcap_adc_quirk_reset_lost_irq(ddata);
 			error = -ETIMEDOUT;
 			continue;
 		}
@@ -664,6 +662,21 @@ static int cpcap_adc_start_bank(struct cpcap_adc *ddata,
 	return error;
 }
 
+static int cpcap_adc_stop_bank(struct cpcap_adc *ddata)
+{
+	int error;
+
+	error = regmap_update_bits(ddata->reg, CPCAP_REG_ADCC1,
+				   0xffff,
+				   CPCAP_REG_ADCC1_DEFAULTS);
+	if (error)
+		return error;
+
+	return regmap_update_bits(ddata->reg, CPCAP_REG_ADCC2,
+				  0xffff,
+				  CPCAP_REG_ADCC2_DEFAULTS);
+}
+
 static void cpcap_adc_phase(struct cpcap_adc_request *req)
 {
 	const struct cpcap_adc_conversion_tbl *conv_tbl = req->conv_tbl;
@@ -758,7 +771,7 @@ static void cpcap_adc_convert(struct cpcap_adc_request *req)
 		return;
 
 	/* Temperatures use a lookup table instead of conversion table */
-	if ((req->channel == CPCAP_ADC_AD0_BATTDETB) ||
+	if ((req->channel == CPCAP_ADC_AD0) ||
 	    (req->channel == CPCAP_ADC_AD3)) {
 		req->result =
 			cpcap_adc_table_to_millicelcius(req->result);
@@ -820,7 +833,7 @@ static int cpcap_adc_init_request(struct cpcap_adc_request *req,
 	req->conv_tbl = bank_conversion;
 
 	switch (channel) {
-	case CPCAP_ADC_AD0_BATTDETB ... CPCAP_ADC_USB_ID:
+	case CPCAP_ADC_AD0 ... CPCAP_ADC_USB_ID:
 		req->bank_index = channel;
 		break;
 	case CPCAP_ADC_AD8 ... CPCAP_ADC_TSY2_AD15:
@@ -839,6 +852,22 @@ static int cpcap_adc_init_request(struct cpcap_adc_request *req,
 	return 0;
 }
 
+static int cpcap_adc_read_st_die_temp(struct cpcap_adc *ddata,
+				      int addr, int *val)
+{
+	int error;
+
+	error = regmap_read(ddata->reg, addr, val);
+	if (error)
+		return error;
+
+	*val -= 282;
+	*val *= 114;
+	*val += 25000;
+
+	return 0;
+}
+
 static int cpcap_adc_read(struct iio_dev *indio_dev,
 			  struct iio_chan_spec const *chan,
 			  int *val, int *val2, long mask)
@@ -860,6 +889,9 @@ static int cpcap_adc_read(struct iio_dev *indio_dev,
 		error = regmap_read(ddata->reg, chan->address, val);
 		if (error)
 			goto err_unlock;
+		error = cpcap_adc_stop_bank(ddata);
+		if (error)
+			goto err_unlock;
 		mutex_unlock(&ddata->lock);
 		break;
 	case IIO_CHAN_INFO_PROCESSED:
@@ -867,7 +899,19 @@ static int cpcap_adc_read(struct iio_dev *indio_dev,
 		error = cpcap_adc_start_bank(ddata, &req);
 		if (error)
 			goto err_unlock;
-		error = cpcap_adc_read_bank_scaled(ddata, &req);
+		if ((ddata->vendor == CPCAP_VENDOR_ST) &&
+		    (chan->channel == CPCAP_ADC_AD3)) {
+			error = cpcap_adc_read_st_die_temp(ddata,
+							   chan->address,
+							   &req.result);
+			if (error)
+				goto err_unlock;
+		} else {
+			error = cpcap_adc_read_bank_scaled(ddata, &req);
+			if (error)
+				goto err_unlock;
+		}
+		error = cpcap_adc_stop_bank(ddata);
 		if (error)
 			goto err_unlock;
 		mutex_unlock(&ddata->lock);
diff --git a/drivers/iio/adc/hi8435.c b/drivers/iio/adc/hi8435.c
index ab59969b7c49..adf7dc712937 100644
--- a/drivers/iio/adc/hi8435.c
+++ b/drivers/iio/adc/hi8435.c
@@ -410,11 +410,11 @@ static const struct iio_chan_spec hi8435_channels[] = {
 static const struct iio_info hi8435_info = {
 	.driver_module = THIS_MODULE,
 	.read_raw = hi8435_read_raw,
-	.read_event_config = &hi8435_read_event_config,
+	.read_event_config = hi8435_read_event_config,
 	.write_event_config = hi8435_write_event_config,
-	.read_event_value = &hi8435_read_event_value,
-	.write_event_value = &hi8435_write_event_value,
-	.debugfs_reg_access = &hi8435_debugfs_reg_access,
+	.read_event_value = hi8435_read_event_value,
+	.write_event_value = hi8435_write_event_value,
+	.debugfs_reg_access = hi8435_debugfs_reg_access,
 };
 
 static void hi8435_iio_push_event(struct iio_dev *idev, unsigned int val)
@@ -476,15 +476,13 @@ static int hi8435_probe(struct spi_device *spi)
 	priv->spi = spi;
 
 	reset_gpio = devm_gpiod_get(&spi->dev, NULL, GPIOD_OUT_LOW);
-	if (!IS_ERR(reset_gpio)) {
-		/* need >=100ns low pulse to reset chip */
-		gpiod_set_raw_value_cansleep(reset_gpio, 0);
-		udelay(1);
-		gpiod_set_raw_value_cansleep(reset_gpio, 1);
-	} else {
-		/* s/w reset chip if h/w reset is not available */
+	if (IS_ERR(reset_gpio)) {
+		/* chip s/w reset if h/w reset failed */
 		hi8435_writeb(priv, HI8435_CTRL_REG, HI8435_CTRL_SRST);
 		hi8435_writeb(priv, HI8435_CTRL_REG, 0);
+	} else {
+		udelay(5);
+		gpiod_set_value(reset_gpio, 1);
 	}
 
 	spi_set_drvdata(spi, idev);
diff --git a/drivers/iio/adc/ina2xx-adc.c b/drivers/iio/adc/ina2xx-adc.c
index 6b588ac3130c..232c0b80d658 100644
--- a/drivers/iio/adc/ina2xx-adc.c
+++ b/drivers/iio/adc/ina2xx-adc.c
@@ -49,6 +49,7 @@
 
 /* settings - depend on use case */
 #define INA219_CONFIG_DEFAULT           0x399F	/* PGA=8 */
+#define INA219_DEFAULT_IT		532
 #define INA226_CONFIG_DEFAULT           0x4327
 #define INA226_DEFAULT_AVG              4
 #define INA226_DEFAULT_IT		1110
@@ -56,19 +57,24 @@
 #define INA2XX_RSHUNT_DEFAULT           10000
 
 /*
- * bit mask for reading the averaging setting in the configuration register
+ * bit masks for reading the settings in the configuration register
  * FIXME: use regmap_fields.
  */
 #define INA2XX_MODE_MASK	GENMASK(3, 0)
 
+/* Averaging for VBus/VShunt/Power */
 #define INA226_AVG_MASK		GENMASK(11, 9)
 #define INA226_SHIFT_AVG(val)	((val) << 9)
 
 /* Integration time for VBus */
+#define INA219_ITB_MASK		GENMASK(10, 7)
+#define INA219_SHIFT_ITB(val)	((val) << 7)
 #define INA226_ITB_MASK		GENMASK(8, 6)
 #define INA226_SHIFT_ITB(val)	((val) << 6)
 
 /* Integration time for VShunt */
+#define INA219_ITS_MASK		GENMASK(6, 3)
+#define INA219_SHIFT_ITS(val)	((val) << 3)
 #define INA226_ITS_MASK		GENMASK(5, 3)
 #define INA226_SHIFT_ITS(val)	((val) << 3)
 
@@ -108,6 +114,7 @@ struct ina2xx_config {
 	int bus_voltage_shift;
 	int bus_voltage_lsb;	/* uV */
 	int power_lsb;		/* uW */
+	enum ina2xx_ids chip_id;
 };
 
 struct ina2xx_chip_info {
@@ -130,6 +137,7 @@ static const struct ina2xx_config ina2xx_config[] = {
 		.bus_voltage_shift = 3,
 		.bus_voltage_lsb = 4000,
 		.power_lsb = 20000,
+		.chip_id = ina219,
 	},
 	[ina226] = {
 		.config_default = INA226_CONFIG_DEFAULT,
@@ -138,6 +146,7 @@ static const struct ina2xx_config ina2xx_config[] = {
 		.bus_voltage_shift = 0,
 		.bus_voltage_lsb = 1250,
 		.power_lsb = 25000,
+		.chip_id = ina226,
 	},
 };
 
@@ -283,6 +292,66 @@ static int ina226_set_int_time_vshunt(struct ina2xx_chip_info *chip,
 	return 0;
 }
 
+/* Conversion times in uS. */
+static const int ina219_conv_time_tab_subsample[] = { 84, 148, 276, 532 };
+static const int ina219_conv_time_tab_average[] = { 532, 1060, 2130, 4260,
+						    8510, 17020, 34050, 68100};
+
+static int ina219_lookup_int_time(unsigned int *val_us, int *bits)
+{
+	if (*val_us > 68100 || *val_us < 84)
+		return -EINVAL;
+
+	if (*val_us <= 532) {
+		*bits = find_closest(*val_us, ina219_conv_time_tab_subsample,
+				    ARRAY_SIZE(ina219_conv_time_tab_subsample));
+		*val_us = ina219_conv_time_tab_subsample[*bits];
+	} else {
+		*bits = find_closest(*val_us, ina219_conv_time_tab_average,
+				    ARRAY_SIZE(ina219_conv_time_tab_average));
+		*val_us = ina219_conv_time_tab_average[*bits];
+		*bits |= 0x8;
+	}
+
+	return 0;
+}
+
+static int ina219_set_int_time_vbus(struct ina2xx_chip_info *chip,
+				    unsigned int val_us, unsigned int *config)
+{
+	int bits, ret;
+	unsigned int val_us_best = val_us;
+
+	ret = ina219_lookup_int_time(&val_us_best, &bits);
+	if (ret)
+		return ret;
+
+	chip->int_time_vbus = val_us_best;
+
+	*config &= ~INA219_ITB_MASK;
+	*config |= INA219_SHIFT_ITB(bits) & INA219_ITB_MASK;
+
+	return 0;
+}
+
+static int ina219_set_int_time_vshunt(struct ina2xx_chip_info *chip,
+				      unsigned int val_us, unsigned int *config)
+{
+	int bits, ret;
+	unsigned int val_us_best = val_us;
+
+	ret = ina219_lookup_int_time(&val_us_best, &bits);
+	if (ret)
+		return ret;
+
+	chip->int_time_vshunt = val_us_best;
+
+	*config &= ~INA219_ITS_MASK;
+	*config |= INA219_SHIFT_ITS(bits) & INA219_ITS_MASK;
+
+	return 0;
+}
+
 static int ina2xx_write_raw(struct iio_dev *indio_dev,
 			    struct iio_chan_spec const *chan,
 			    int val, int val2, long mask)
@@ -308,10 +377,21 @@ static int ina2xx_write_raw(struct iio_dev *indio_dev,
 		break;
 
 	case IIO_CHAN_INFO_INT_TIME:
-		if (chan->address == INA2XX_SHUNT_VOLTAGE)
-			ret = ina226_set_int_time_vshunt(chip, val2, &tmp);
-		else
-			ret = ina226_set_int_time_vbus(chip, val2, &tmp);
+		if (chip->config->chip_id == ina226) {
+			if (chan->address == INA2XX_SHUNT_VOLTAGE)
+				ret = ina226_set_int_time_vshunt(chip, val2,
+								 &tmp);
+			else
+				ret = ina226_set_int_time_vbus(chip, val2,
+							       &tmp);
+		} else {
+			if (chan->address == INA2XX_SHUNT_VOLTAGE)
+				ret = ina219_set_int_time_vshunt(chip, val2,
+								 &tmp);
+			else
+				ret = ina219_set_int_time_vbus(chip, val2,
+							       &tmp);
+		}
 		break;
 
 	default:
@@ -412,7 +492,24 @@ static ssize_t ina2xx_shunt_resistor_store(struct device *dev,
 	return len;
 }
 
-#define INA2XX_CHAN(_type, _index, _address) { \
+#define INA219_CHAN(_type, _index, _address) { \
+	.type = (_type), \
+	.address = (_address), \
+	.indexed = 1, \
+	.channel = (_index), \
+	.info_mask_separate = BIT(IIO_CHAN_INFO_RAW) | \
+			      BIT(IIO_CHAN_INFO_SCALE), \
+	.info_mask_shared_by_dir = BIT(IIO_CHAN_INFO_SAMP_FREQ), \
+	.scan_index = (_index), \
+	.scan_type = { \
+		.sign = 'u', \
+		.realbits = 16, \
+		.storagebits = 16, \
+		.endianness = IIO_CPU, \
+	} \
+}
+
+#define INA226_CHAN(_type, _index, _address) { \
 	.type = (_type), \
 	.address = (_address), \
 	.indexed = 1, \
@@ -434,7 +531,25 @@ static ssize_t ina2xx_shunt_resistor_store(struct device *dev,
  * Sampling Freq is a consequence of the integration times of
  * the Voltage channels.
  */
-#define INA2XX_CHAN_VOLTAGE(_index, _address) { \
+#define INA219_CHAN_VOLTAGE(_index, _address) { \
+	.type = IIO_VOLTAGE, \
+	.address = (_address), \
+	.indexed = 1, \
+	.channel = (_index), \
+	.info_mask_separate = BIT(IIO_CHAN_INFO_RAW) | \
+			      BIT(IIO_CHAN_INFO_SCALE) | \
+			      BIT(IIO_CHAN_INFO_INT_TIME), \
+	.info_mask_shared_by_dir = BIT(IIO_CHAN_INFO_SAMP_FREQ), \
+	.scan_index = (_index), \
+	.scan_type = { \
+		.sign = 'u', \
+		.realbits = 16, \
+		.storagebits = 16, \
+		.endianness = IIO_LE, \
+	} \
+}
+
+#define INA226_CHAN_VOLTAGE(_index, _address) { \
 	.type = IIO_VOLTAGE, \
 	.address = (_address), \
 	.indexed = 1, \
@@ -442,6 +557,8 @@ static ssize_t ina2xx_shunt_resistor_store(struct device *dev,
 	.info_mask_separate = BIT(IIO_CHAN_INFO_RAW) | \
 			      BIT(IIO_CHAN_INFO_SCALE) | \
 			      BIT(IIO_CHAN_INFO_INT_TIME), \
+	.info_mask_shared_by_dir = BIT(IIO_CHAN_INFO_SAMP_FREQ) | \
+				   BIT(IIO_CHAN_INFO_OVERSAMPLING_RATIO), \
 	.scan_index = (_index), \
 	.scan_type = { \
 		.sign = 'u', \
@@ -451,11 +568,20 @@ static ssize_t ina2xx_shunt_resistor_store(struct device *dev,
 	} \
 }
 
-static const struct iio_chan_spec ina2xx_channels[] = {
-	INA2XX_CHAN_VOLTAGE(0, INA2XX_SHUNT_VOLTAGE),
-	INA2XX_CHAN_VOLTAGE(1, INA2XX_BUS_VOLTAGE),
-	INA2XX_CHAN(IIO_POWER, 2, INA2XX_POWER),
-	INA2XX_CHAN(IIO_CURRENT, 3, INA2XX_CURRENT),
+
+static const struct iio_chan_spec ina226_channels[] = {
+	INA226_CHAN_VOLTAGE(0, INA2XX_SHUNT_VOLTAGE),
+	INA226_CHAN_VOLTAGE(1, INA2XX_BUS_VOLTAGE),
+	INA226_CHAN(IIO_POWER, 2, INA2XX_POWER),
+	INA226_CHAN(IIO_CURRENT, 3, INA2XX_CURRENT),
+	IIO_CHAN_SOFT_TIMESTAMP(4),
+};
+
+static const struct iio_chan_spec ina219_channels[] = {
+	INA219_CHAN_VOLTAGE(0, INA2XX_SHUNT_VOLTAGE),
+	INA219_CHAN_VOLTAGE(1, INA2XX_BUS_VOLTAGE),
+	INA219_CHAN(IIO_POWER, 2, INA2XX_POWER),
+	INA219_CHAN(IIO_CURRENT, 3, INA2XX_CURRENT),
 	IIO_CHAN_SOFT_TIMESTAMP(4),
 };
 
@@ -590,7 +716,14 @@ static int ina2xx_debug_reg(struct iio_dev *indio_dev,
 }
 
 /* Possible integration times for vshunt and vbus */
-static IIO_CONST_ATTR_INT_TIME_AVAIL("0.000140 0.000204 0.000332 0.000588 0.001100 0.002116 0.004156 0.008244");
+static IIO_CONST_ATTR_NAMED(ina219_integration_time_available,
+			    integration_time_available,
+			    "0.000084 0.000148 0.000276 0.000532 0.001060 0.002130 0.004260 0.008510 0.017020 0.034050 0.068100");
+
+static IIO_CONST_ATTR_NAMED(ina226_integration_time_available,
+			    integration_time_available,
+			    "0.000140 0.000204 0.000332 0.000588 0.001100 0.002116 0.004156 0.008244");
+
 
 static IIO_DEVICE_ATTR(in_allow_async_readout, S_IRUGO | S_IWUSR,
 		       ina2xx_allow_async_readout_show,
@@ -600,20 +733,39 @@ static IIO_DEVICE_ATTR(in_shunt_resistor, S_IRUGO | S_IWUSR,
 		       ina2xx_shunt_resistor_show,
 		       ina2xx_shunt_resistor_store, 0);
 
-static struct attribute *ina2xx_attributes[] = {
+static struct attribute *ina219_attributes[] = {
+	&iio_dev_attr_in_allow_async_readout.dev_attr.attr,
+	&iio_const_attr_ina219_integration_time_available.dev_attr.attr,
+	&iio_dev_attr_in_shunt_resistor.dev_attr.attr,
+	NULL,
+};
+
+static struct attribute *ina226_attributes[] = {
 	&iio_dev_attr_in_allow_async_readout.dev_attr.attr,
-	&iio_const_attr_integration_time_available.dev_attr.attr,
+	&iio_const_attr_ina226_integration_time_available.dev_attr.attr,
 	&iio_dev_attr_in_shunt_resistor.dev_attr.attr,
 	NULL,
 };
 
-static const struct attribute_group ina2xx_attribute_group = {
-	.attrs = ina2xx_attributes,
+static const struct attribute_group ina219_attribute_group = {
+	.attrs = ina219_attributes,
+};
+
+static const struct attribute_group ina226_attribute_group = {
+	.attrs = ina226_attributes,
 };
 
-static const struct iio_info ina2xx_info = {
+static const struct iio_info ina219_info = {
 	.driver_module = THIS_MODULE,
-	.attrs = &ina2xx_attribute_group,
+	.attrs = &ina219_attribute_group,
+	.read_raw = ina2xx_read_raw,
+	.write_raw = ina2xx_write_raw,
+	.debugfs_reg_access = ina2xx_debug_reg,
+};
+
+static const struct iio_info ina226_info = {
+	.driver_module = THIS_MODULE,
+	.attrs = &ina226_attribute_group,
 	.read_raw = ina2xx_read_raw,
 	.write_raw = ina2xx_write_raw,
 	.debugfs_reg_access = ina2xx_debug_reg,
@@ -684,6 +836,10 @@ static int ina2xx_probe(struct i2c_client *client,
 		ina226_set_average(chip, INA226_DEFAULT_AVG, &val);
 		ina226_set_int_time_vbus(chip, INA226_DEFAULT_IT, &val);
 		ina226_set_int_time_vshunt(chip, INA226_DEFAULT_IT, &val);
+	} else {
+		chip->avg = 1;
+		ina219_set_int_time_vbus(chip, INA219_DEFAULT_IT, &val);
+		ina219_set_int_time_vshunt(chip, INA219_DEFAULT_IT, &val);
 	}
 
 	ret = ina2xx_init(chip, val);
@@ -695,10 +851,16 @@ static int ina2xx_probe(struct i2c_client *client,
 	indio_dev->modes = INDIO_DIRECT_MODE | INDIO_BUFFER_SOFTWARE;
 	indio_dev->dev.parent = &client->dev;
 	indio_dev->dev.of_node = client->dev.of_node;
-	indio_dev->channels = ina2xx_channels;
-	indio_dev->num_channels = ARRAY_SIZE(ina2xx_channels);
+	if (id->driver_data == ina226) {
+		indio_dev->channels = ina226_channels;
+		indio_dev->num_channels = ARRAY_SIZE(ina226_channels);
+		indio_dev->info = &ina226_info;
+	} else {
+		indio_dev->channels = ina219_channels;
+		indio_dev->num_channels = ARRAY_SIZE(ina219_channels);
+		indio_dev->info = &ina219_info;
+	}
 	indio_dev->name = id->name;
-	indio_dev->info = &ina2xx_info;
 	indio_dev->setup_ops = &ina2xx_setup_ops;
 
 	buffer = devm_iio_kfifo_allocate(&indio_dev->dev);
diff --git a/drivers/iio/adc/lpc32xx_adc.c b/drivers/iio/adc/lpc32xx_adc.c
index 0de709b4288b..6a5b9a9bc662 100644
--- a/drivers/iio/adc/lpc32xx_adc.c
+++ b/drivers/iio/adc/lpc32xx_adc.c
@@ -76,10 +76,14 @@ static int lpc32xx_read_raw(struct iio_dev *indio_dev,
 			    long mask)
 {
 	struct lpc32xx_adc_state *st = iio_priv(indio_dev);
-
+	int ret;
 	if (mask == IIO_CHAN_INFO_RAW) {
 		mutex_lock(&indio_dev->mlock);
-		clk_prepare_enable(st->clk);
+		ret = clk_prepare_enable(st->clk);
+		if (ret) {
+			mutex_unlock(&indio_dev->mlock);
+			return ret;
+		}
 		/* Measurement setup */
 		__raw_writel(LPC32XXAD_INTERNAL | (chan->address) |
 			     LPC32XXAD_REFp | LPC32XXAD_REFm,
diff --git a/drivers/iio/adc/mxs-lradc-adc.c b/drivers/iio/adc/mxs-lradc-adc.c
index 6888167ca1e6..d32b34638c2f 100644
--- a/drivers/iio/adc/mxs-lradc-adc.c
+++ b/drivers/iio/adc/mxs-lradc-adc.c
@@ -48,7 +48,7 @@
 
 #define VREF_MV_BASE 1850
 
-const char *mx23_lradc_adc_irq_names[] = {
+static const char *mx23_lradc_adc_irq_names[] = {
 	"mxs-lradc-channel0",
 	"mxs-lradc-channel1",
 	"mxs-lradc-channel2",
@@ -57,7 +57,7 @@ const char *mx23_lradc_adc_irq_names[] = {
 	"mxs-lradc-channel5",
 };
 
-const char *mx28_lradc_adc_irq_names[] = {
+static const char *mx28_lradc_adc_irq_names[] = {
 	"mxs-lradc-thresh0",
 	"mxs-lradc-thresh1",
 	"mxs-lradc-channel0",
@@ -344,20 +344,20 @@ static ssize_t mxs_lradc_adc_show_scale_avail(struct device *dev,
 	IIO_DEVICE_ATTR(in_voltage##ch##_scale_available, 0444,\
 			mxs_lradc_adc_show_scale_avail, NULL, ch)
 
-SHOW_SCALE_AVAILABLE_ATTR(0);
-SHOW_SCALE_AVAILABLE_ATTR(1);
-SHOW_SCALE_AVAILABLE_ATTR(2);
-SHOW_SCALE_AVAILABLE_ATTR(3);
-SHOW_SCALE_AVAILABLE_ATTR(4);
-SHOW_SCALE_AVAILABLE_ATTR(5);
-SHOW_SCALE_AVAILABLE_ATTR(6);
-SHOW_SCALE_AVAILABLE_ATTR(7);
-SHOW_SCALE_AVAILABLE_ATTR(10);
-SHOW_SCALE_AVAILABLE_ATTR(11);
-SHOW_SCALE_AVAILABLE_ATTR(12);
-SHOW_SCALE_AVAILABLE_ATTR(13);
-SHOW_SCALE_AVAILABLE_ATTR(14);
-SHOW_SCALE_AVAILABLE_ATTR(15);
+static SHOW_SCALE_AVAILABLE_ATTR(0);
+static SHOW_SCALE_AVAILABLE_ATTR(1);
+static SHOW_SCALE_AVAILABLE_ATTR(2);
+static SHOW_SCALE_AVAILABLE_ATTR(3);
+static SHOW_SCALE_AVAILABLE_ATTR(4);
+static SHOW_SCALE_AVAILABLE_ATTR(5);
+static SHOW_SCALE_AVAILABLE_ATTR(6);
+static SHOW_SCALE_AVAILABLE_ATTR(7);
+static SHOW_SCALE_AVAILABLE_ATTR(10);
+static SHOW_SCALE_AVAILABLE_ATTR(11);
+static SHOW_SCALE_AVAILABLE_ATTR(12);
+static SHOW_SCALE_AVAILABLE_ATTR(13);
+static SHOW_SCALE_AVAILABLE_ATTR(14);
+static SHOW_SCALE_AVAILABLE_ATTR(15);
 
 static struct attribute *mxs_lradc_adc_attributes[] = {
 	&iio_dev_attr_in_voltage0_scale_available.dev_attr.attr,
diff --git a/drivers/iio/adc/stm32-adc-core.c b/drivers/iio/adc/stm32-adc-core.c
index 22b7c9321e78..e09233b03c05 100644
--- a/drivers/iio/adc/stm32-adc-core.c
+++ b/drivers/iio/adc/stm32-adc-core.c
@@ -49,19 +49,66 @@
 /* STM32 F4 maximum analog clock rate (from datasheet) */
 #define STM32F4_ADC_MAX_CLK_RATE	36000000
 
+/* STM32H7 - common registers for all ADC instances */
+#define STM32H7_ADC_CSR			(STM32_ADCX_COMN_OFFSET + 0x00)
+#define STM32H7_ADC_CCR			(STM32_ADCX_COMN_OFFSET + 0x08)
+
+/* STM32H7_ADC_CSR - bit fields */
+#define STM32H7_EOC_SLV			BIT(18)
+#define STM32H7_EOC_MST			BIT(2)
+
+/* STM32H7_ADC_CCR - bit fields */
+#define STM32H7_PRESC_SHIFT		18
+#define STM32H7_PRESC_MASK		GENMASK(21, 18)
+#define STM32H7_CKMODE_SHIFT		16
+#define STM32H7_CKMODE_MASK		GENMASK(17, 16)
+
+/* STM32 H7 maximum analog clock rate (from datasheet) */
+#define STM32H7_ADC_MAX_CLK_RATE	72000000
+
+/**
+ * stm32_adc_common_regs - stm32 common registers, compatible dependent data
+ * @csr:	common status register offset
+ * @eoc1:	adc1 end of conversion flag in @csr
+ * @eoc2:	adc2 end of conversion flag in @csr
+ * @eoc3:	adc3 end of conversion flag in @csr
+ */
+struct stm32_adc_common_regs {
+	u32 csr;
+	u32 eoc1_msk;
+	u32 eoc2_msk;
+	u32 eoc3_msk;
+};
+
+struct stm32_adc_priv;
+
+/**
+ * stm32_adc_priv_cfg - stm32 core compatible configuration data
+ * @regs:	common registers for all instances
+ * @clk_sel:	clock selection routine
+ */
+struct stm32_adc_priv_cfg {
+	const struct stm32_adc_common_regs *regs;
+	int (*clk_sel)(struct platform_device *, struct stm32_adc_priv *);
+};
+
 /**
  * struct stm32_adc_priv - stm32 ADC core private data
  * @irq:		irq for ADC block
  * @domain:		irq domain reference
  * @aclk:		clock reference for the analog circuitry
+ * @bclk:		bus clock common for all ADCs, depends on part used
  * @vref:		regulator reference
+ * @cfg:		compatible configuration data
  * @common:		common data for all ADC instances
  */
 struct stm32_adc_priv {
 	int				irq;
 	struct irq_domain		*domain;
 	struct clk			*aclk;
+	struct clk			*bclk;
 	struct regulator		*vref;
+	const struct stm32_adc_priv_cfg	*cfg;
 	struct stm32_adc_common		common;
 };
 
@@ -85,14 +132,23 @@ static int stm32f4_adc_clk_sel(struct platform_device *pdev,
 	u32 val;
 	int i;
 
+	/* stm32f4 has one clk input for analog (mandatory), enforce it here */
+	if (!priv->aclk) {
+		dev_err(&pdev->dev, "No 'adc' clock found\n");
+		return -ENOENT;
+	}
+
 	rate = clk_get_rate(priv->aclk);
 	for (i = 0; i < ARRAY_SIZE(stm32f4_pclk_div); i++) {
 		if ((rate / stm32f4_pclk_div[i]) <= STM32F4_ADC_MAX_CLK_RATE)
 			break;
 	}
-	if (i >= ARRAY_SIZE(stm32f4_pclk_div))
+	if (i >= ARRAY_SIZE(stm32f4_pclk_div)) {
+		dev_err(&pdev->dev, "adc clk selection failed\n");
 		return -EINVAL;
+	}
 
+	priv->common.rate = rate;
 	val = readl_relaxed(priv->common.base + STM32F4_ADC_CCR);
 	val &= ~STM32F4_ADC_ADCPRE_MASK;
 	val |= i << STM32F4_ADC_ADCPRE_SHIFT;
@@ -104,6 +160,126 @@ static int stm32f4_adc_clk_sel(struct platform_device *pdev,
 	return 0;
 }
 
+/**
+ * struct stm32h7_adc_ck_spec - specification for stm32h7 adc clock
+ * @ckmode: ADC clock mode, Async or sync with prescaler.
+ * @presc: prescaler bitfield for async clock mode
+ * @div: prescaler division ratio
+ */
+struct stm32h7_adc_ck_spec {
+	u32 ckmode;
+	u32 presc;
+	int div;
+};
+
+const struct stm32h7_adc_ck_spec stm32h7_adc_ckmodes_spec[] = {
+	/* 00: CK_ADC[1..3]: Asynchronous clock modes */
+	{ 0, 0, 1 },
+	{ 0, 1, 2 },
+	{ 0, 2, 4 },
+	{ 0, 3, 6 },
+	{ 0, 4, 8 },
+	{ 0, 5, 10 },
+	{ 0, 6, 12 },
+	{ 0, 7, 16 },
+	{ 0, 8, 32 },
+	{ 0, 9, 64 },
+	{ 0, 10, 128 },
+	{ 0, 11, 256 },
+	/* HCLK used: Synchronous clock modes (1, 2 or 4 prescaler) */
+	{ 1, 0, 1 },
+	{ 2, 0, 2 },
+	{ 3, 0, 4 },
+};
+
+static int stm32h7_adc_clk_sel(struct platform_device *pdev,
+			       struct stm32_adc_priv *priv)
+{
+	u32 ckmode, presc, val;
+	unsigned long rate;
+	int i, div;
+
+	/* stm32h7 bus clock is common for all ADC instances (mandatory) */
+	if (!priv->bclk) {
+		dev_err(&pdev->dev, "No 'bus' clock found\n");
+		return -ENOENT;
+	}
+
+	/*
+	 * stm32h7 can use either 'bus' or 'adc' clock for analog circuitry.
+	 * So, choice is to have bus clock mandatory and adc clock optional.
+	 * If optional 'adc' clock has been found, then try to use it first.
+	 */
+	if (priv->aclk) {
+		/*
+		 * Asynchronous clock modes (e.g. ckmode == 0)
+		 * From spec: PLL output musn't exceed max rate
+		 */
+		rate = clk_get_rate(priv->aclk);
+
+		for (i = 0; i < ARRAY_SIZE(stm32h7_adc_ckmodes_spec); i++) {
+			ckmode = stm32h7_adc_ckmodes_spec[i].ckmode;
+			presc = stm32h7_adc_ckmodes_spec[i].presc;
+			div = stm32h7_adc_ckmodes_spec[i].div;
+
+			if (ckmode)
+				continue;
+
+			if ((rate / div) <= STM32H7_ADC_MAX_CLK_RATE)
+				goto out;
+		}
+	}
+
+	/* Synchronous clock modes (e.g. ckmode is 1, 2 or 3) */
+	rate = clk_get_rate(priv->bclk);
+
+	for (i = 0; i < ARRAY_SIZE(stm32h7_adc_ckmodes_spec); i++) {
+		ckmode = stm32h7_adc_ckmodes_spec[i].ckmode;
+		presc = stm32h7_adc_ckmodes_spec[i].presc;
+		div = stm32h7_adc_ckmodes_spec[i].div;
+
+		if (!ckmode)
+			continue;
+
+		if ((rate / div) <= STM32H7_ADC_MAX_CLK_RATE)
+			goto out;
+	}
+
+	dev_err(&pdev->dev, "adc clk selection failed\n");
+	return -EINVAL;
+
+out:
+	/* rate used later by each ADC instance to control BOOST mode */
+	priv->common.rate = rate;
+
+	/* Set common clock mode and prescaler */
+	val = readl_relaxed(priv->common.base + STM32H7_ADC_CCR);
+	val &= ~(STM32H7_CKMODE_MASK | STM32H7_PRESC_MASK);
+	val |= ckmode << STM32H7_CKMODE_SHIFT;
+	val |= presc << STM32H7_PRESC_SHIFT;
+	writel_relaxed(val, priv->common.base + STM32H7_ADC_CCR);
+
+	dev_dbg(&pdev->dev, "Using %s clock/%d source at %ld kHz\n",
+		ckmode ? "bus" : "adc", div, rate / (div * 1000));
+
+	return 0;
+}
+
+/* STM32F4 common registers definitions */
+static const struct stm32_adc_common_regs stm32f4_adc_common_regs = {
+	.csr = STM32F4_ADC_CSR,
+	.eoc1_msk = STM32F4_EOC1,
+	.eoc2_msk = STM32F4_EOC2,
+	.eoc3_msk = STM32F4_EOC3,
+};
+
+/* STM32H7 common registers definitions */
+static const struct stm32_adc_common_regs stm32h7_adc_common_regs = {
+	.csr = STM32H7_ADC_CSR,
+	.eoc1_msk = STM32H7_EOC_MST,
+	.eoc2_msk = STM32H7_EOC_SLV,
+};
+
 /* ADC common interrupt for all instances */
 static void stm32_adc_irq_handler(struct irq_desc *desc)
 {
@@ -112,15 +288,15 @@ static void stm32_adc_irq_handler(struct irq_desc *desc)
 	u32 status;
 
 	chained_irq_enter(chip, desc);
-	status = readl_relaxed(priv->common.base + STM32F4_ADC_CSR);
+	status = readl_relaxed(priv->common.base + priv->cfg->regs->csr);
 
-	if (status & STM32F4_EOC1)
+	if (status & priv->cfg->regs->eoc1_msk)
 		generic_handle_irq(irq_find_mapping(priv->domain, 0));
 
-	if (status & STM32F4_EOC2)
+	if (status & priv->cfg->regs->eoc2_msk)
 		generic_handle_irq(irq_find_mapping(priv->domain, 1));
 
-	if (status & STM32F4_EOC3)
+	if (status & priv->cfg->regs->eoc3_msk)
 		generic_handle_irq(irq_find_mapping(priv->domain, 2));
 
 	chained_irq_exit(chip, desc);
@@ -186,6 +362,7 @@ static void stm32_adc_irq_remove(struct platform_device *pdev,
 static int stm32_adc_probe(struct platform_device *pdev)
 {
 	struct stm32_adc_priv *priv;
+	struct device *dev = &pdev->dev;
 	struct device_node *np = pdev->dev.of_node;
 	struct resource *res;
 	int ret;
@@ -197,6 +374,9 @@ static int stm32_adc_probe(struct platform_device *pdev)
 	if (!priv)
 		return -ENOMEM;
 
+	priv->cfg = (const struct stm32_adc_priv_cfg *)
+		of_match_device(dev->driver->of_match_table, dev)->data;
+
 	res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
 	priv->common.base = devm_ioremap_resource(&pdev->dev, res);
 	if (IS_ERR(priv->common.base))
@@ -227,25 +407,48 @@ static int stm32_adc_probe(struct platform_device *pdev)
 	priv->aclk = devm_clk_get(&pdev->dev, "adc");
 	if (IS_ERR(priv->aclk)) {
 		ret = PTR_ERR(priv->aclk);
-		dev_err(&pdev->dev, "Can't get 'adc' clock\n");
-		goto err_regulator_disable;
+		if (ret == -ENOENT) {
+			priv->aclk = NULL;
+		} else {
+			dev_err(&pdev->dev, "Can't get 'adc' clock\n");
+			goto err_regulator_disable;
+		}
 	}
 
-	ret = clk_prepare_enable(priv->aclk);
-	if (ret < 0) {
-		dev_err(&pdev->dev, "adc clk enable failed\n");
-		goto err_regulator_disable;
+	if (priv->aclk) {
+		ret = clk_prepare_enable(priv->aclk);
+		if (ret < 0) {
+			dev_err(&pdev->dev, "adc clk enable failed\n");
+			goto err_regulator_disable;
+		}
 	}
 
-	ret = stm32f4_adc_clk_sel(pdev, priv);
-	if (ret < 0) {
-		dev_err(&pdev->dev, "adc clk selection failed\n");
-		goto err_clk_disable;
+	priv->bclk = devm_clk_get(&pdev->dev, "bus");
+	if (IS_ERR(priv->bclk)) {
+		ret = PTR_ERR(priv->bclk);
+		if (ret == -ENOENT) {
+			priv->bclk = NULL;
+		} else {
+			dev_err(&pdev->dev, "Can't get 'bus' clock\n");
+			goto err_aclk_disable;
+		}
+	}
+
+	if (priv->bclk) {
+		ret = clk_prepare_enable(priv->bclk);
+		if (ret < 0) {
+			dev_err(&pdev->dev, "adc clk enable failed\n");
+			goto err_aclk_disable;
+		}
 	}
 
+	ret = priv->cfg->clk_sel(pdev, priv);
+	if (ret < 0)
+		goto err_bclk_disable;
+
 	ret = stm32_adc_irq_probe(pdev, priv);
 	if (ret < 0)
-		goto err_clk_disable;
+		goto err_bclk_disable;
 
 	platform_set_drvdata(pdev, &priv->common);
 
@@ -260,8 +463,13 @@ static int stm32_adc_probe(struct platform_device *pdev)
 err_irq_remove:
 	stm32_adc_irq_remove(pdev, priv);
 
-err_clk_disable:
-	clk_disable_unprepare(priv->aclk);
+err_bclk_disable:
+	if (priv->bclk)
+		clk_disable_unprepare(priv->bclk);
+
+err_aclk_disable:
+	if (priv->aclk)
+		clk_disable_unprepare(priv->aclk);
 
 err_regulator_disable:
 	regulator_disable(priv->vref);
@@ -276,15 +484,34 @@ static int stm32_adc_remove(struct platform_device *pdev)
 
 	of_platform_depopulate(&pdev->dev);
 	stm32_adc_irq_remove(pdev, priv);
-	clk_disable_unprepare(priv->aclk);
+	if (priv->bclk)
+		clk_disable_unprepare(priv->bclk);
+	if (priv->aclk)
+		clk_disable_unprepare(priv->aclk);
 	regulator_disable(priv->vref);
 
 	return 0;
 }
 
+static const struct stm32_adc_priv_cfg stm32f4_adc_priv_cfg = {
+	.regs = &stm32f4_adc_common_regs,
+	.clk_sel = stm32f4_adc_clk_sel,
+};
+
+static const struct stm32_adc_priv_cfg stm32h7_adc_priv_cfg = {
+	.regs = &stm32h7_adc_common_regs,
+	.clk_sel = stm32h7_adc_clk_sel,
+};
+
 static const struct of_device_id stm32_adc_of_match[] = {
-	{ .compatible = "st,stm32f4-adc-core" },
-	{},
+	{
+		.compatible = "st,stm32f4-adc-core",
+		.data = (void *)&stm32f4_adc_priv_cfg
+	}, {
+		.compatible = "st,stm32h7-adc-core",
+		.data = (void *)&stm32h7_adc_priv_cfg
+	}, {
+	},
 };
 MODULE_DEVICE_TABLE(of, stm32_adc_of_match);
 
diff --git a/drivers/iio/adc/stm32-adc-core.h b/drivers/iio/adc/stm32-adc-core.h
index 2ec7abbfbcaa..250ee958a669 100644
--- a/drivers/iio/adc/stm32-adc-core.h
+++ b/drivers/iio/adc/stm32-adc-core.h
@@ -43,11 +43,13 @@
  * struct stm32_adc_common - stm32 ADC driver common data (for all instances)
  * @base:		control registers base cpu addr
  * @phys_base:		control registers base physical addr
+ * @rate:		clock rate used for analog circuitry
  * @vref_mv:		vref voltage (mv)
  */
 struct stm32_adc_common {
 	void __iomem			*base;
 	phys_addr_t			phys_base;
+	unsigned long			rate;
 	int				vref_mv;
 };
 
diff --git a/drivers/iio/adc/stm32-adc.c b/drivers/iio/adc/stm32-adc.c
index c28e7ff80e11..5bfcc1f13105 100644
--- a/drivers/iio/adc/stm32-adc.c
+++ b/drivers/iio/adc/stm32-adc.c
@@ -31,9 +31,11 @@
 #include <linux/iio/triggered_buffer.h>
 #include <linux/interrupt.h>
 #include <linux/io.h>
+#include <linux/iopoll.h>
 #include <linux/module.h>
 #include <linux/platform_device.h>
 #include <linux/of.h>
+#include <linux/of_device.h>
 
 #include "stm32-adc-core.h"
 
@@ -76,6 +78,78 @@
 #define STM32F4_DMA			BIT(8)
 #define STM32F4_ADON			BIT(0)
 
+/* STM32H7 - Registers for each ADC instance */
+#define STM32H7_ADC_ISR			0x00
+#define STM32H7_ADC_IER			0x04
+#define STM32H7_ADC_CR			0x08
+#define STM32H7_ADC_CFGR		0x0C
+#define STM32H7_ADC_PCSEL		0x1C
+#define STM32H7_ADC_SQR1		0x30
+#define STM32H7_ADC_SQR2		0x34
+#define STM32H7_ADC_SQR3		0x38
+#define STM32H7_ADC_SQR4		0x3C
+#define STM32H7_ADC_DR			0x40
+#define STM32H7_ADC_CALFACT		0xC4
+#define STM32H7_ADC_CALFACT2		0xC8
+
+/* STM32H7_ADC_ISR - bit fields */
+#define STM32H7_EOC			BIT(2)
+#define STM32H7_ADRDY			BIT(0)
+
+/* STM32H7_ADC_IER - bit fields */
+#define STM32H7_EOCIE			STM32H7_EOC
+
+/* STM32H7_ADC_CR - bit fields */
+#define STM32H7_ADCAL			BIT(31)
+#define STM32H7_ADCALDIF		BIT(30)
+#define STM32H7_DEEPPWD			BIT(29)
+#define STM32H7_ADVREGEN		BIT(28)
+#define STM32H7_LINCALRDYW6		BIT(27)
+#define STM32H7_LINCALRDYW5		BIT(26)
+#define STM32H7_LINCALRDYW4		BIT(25)
+#define STM32H7_LINCALRDYW3		BIT(24)
+#define STM32H7_LINCALRDYW2		BIT(23)
+#define STM32H7_LINCALRDYW1		BIT(22)
+#define STM32H7_ADCALLIN		BIT(16)
+#define STM32H7_BOOST			BIT(8)
+#define STM32H7_ADSTP			BIT(4)
+#define STM32H7_ADSTART			BIT(2)
+#define STM32H7_ADDIS			BIT(1)
+#define STM32H7_ADEN			BIT(0)
+
+/* STM32H7_ADC_CFGR bit fields */
+#define STM32H7_EXTEN_SHIFT		10
+#define STM32H7_EXTEN_MASK		GENMASK(11, 10)
+#define STM32H7_EXTSEL_SHIFT		5
+#define STM32H7_EXTSEL_MASK		GENMASK(9, 5)
+#define STM32H7_RES_SHIFT		2
+#define STM32H7_RES_MASK		GENMASK(4, 2)
+#define STM32H7_DMNGT_SHIFT		0
+#define STM32H7_DMNGT_MASK		GENMASK(1, 0)
+
+enum stm32h7_adc_dmngt {
+	STM32H7_DMNGT_DR_ONLY,		/* Regular data in DR only */
+	STM32H7_DMNGT_DMA_ONESHOT,	/* DMA one shot mode */
+	STM32H7_DMNGT_DFSDM,		/* DFSDM mode */
+	STM32H7_DMNGT_DMA_CIRC,		/* DMA circular mode */
+};
+
+/* STM32H7_ADC_CALFACT - bit fields */
+#define STM32H7_CALFACT_D_SHIFT		16
+#define STM32H7_CALFACT_D_MASK		GENMASK(26, 16)
+#define STM32H7_CALFACT_S_SHIFT		0
+#define STM32H7_CALFACT_S_MASK		GENMASK(10, 0)
+
+/* STM32H7_ADC_CALFACT2 - bit fields */
+#define STM32H7_LINCALFACT_SHIFT	0
+#define STM32H7_LINCALFACT_MASK		GENMASK(29, 0)
+
+/* Number of linear calibration shadow registers / LINCALRDYW control bits */
+#define STM32H7_LINCALFACT_NUM		6
+
+/* BOOST bit must be set on STM32H7 when ADC clock is above 20MHz */
+#define STM32H7_BOOST_CLKRATE		20000000UL
+
 #define STM32_ADC_MAX_SQ		16	/* SQ1..SQ16 */
 #define STM32_ADC_TIMEOUT_US		100000
 #define STM32_ADC_TIMEOUT	(msecs_to_jiffies(STM32_ADC_TIMEOUT_US / 1000))
@@ -121,6 +195,18 @@ struct stm32_adc_trig_info {
 };
 
 /**
+ * struct stm32_adc_calib - optional adc calibration data
+ * @calfact_s: Calibration offset for single ended channels
+ * @calfact_d: Calibration offset in differential
+ * @lincalfact: Linearity calibration factor
+ */
+struct stm32_adc_calib {
+	u32			calfact_s;
+	u32			calfact_d;
+	u32			lincalfact[STM32H7_LINCALFACT_NUM];
+};
+
+/**
  * stm32_adc_regs - stm32 ADC misc registers & bitfield desc
  * @reg:		register offset
  * @mask:		bitfield mask
@@ -133,9 +219,56 @@ struct stm32_adc_regs {
 };
 
 /**
+ * stm32_adc_regspec - stm32 registers definition, compatible dependent data
+ * @dr:			data register offset
+ * @ier_eoc:		interrupt enable register & eocie bitfield
+ * @isr_eoc:		interrupt status register & eoc bitfield
+ * @sqr:		reference to sequence registers array
+ * @exten:		trigger control register & bitfield
+ * @extsel:		trigger selection register & bitfield
+ * @res:		resolution selection register & bitfield
+ */
+struct stm32_adc_regspec {
+	const u32 dr;
+	const struct stm32_adc_regs ier_eoc;
+	const struct stm32_adc_regs isr_eoc;
+	const struct stm32_adc_regs *sqr;
+	const struct stm32_adc_regs exten;
+	const struct stm32_adc_regs extsel;
+	const struct stm32_adc_regs res;
+};
+
+struct stm32_adc;
+
+/**
+ * stm32_adc_cfg - stm32 compatible configuration data
+ * @regs:		registers descriptions
+ * @adc_info:		per instance input channels definitions
+ * @trigs:		external trigger sources
+ * @clk_required:	clock is required
+ * @selfcalib:		optional routine for self-calibration
+ * @prepare:		optional prepare routine (power-up, enable)
+ * @start_conv:		routine to start conversions
+ * @stop_conv:		routine to stop conversions
+ * @unprepare:		optional unprepare routine (disable, power-down)
+ */
+struct stm32_adc_cfg {
+	const struct stm32_adc_regspec	*regs;
+	const struct stm32_adc_info	*adc_info;
+	struct stm32_adc_trig_info	*trigs;
+	bool clk_required;
+	int (*selfcalib)(struct stm32_adc *);
+	int (*prepare)(struct stm32_adc *);
+	void (*start_conv)(struct stm32_adc *, bool dma);
+	void (*stop_conv)(struct stm32_adc *);
+	void (*unprepare)(struct stm32_adc *);
+};
+
+/**
  * struct stm32_adc - private data of each ADC IIO instance
  * @common:		reference to ADC block common data
  * @offset:		ADC instance register offset in ADC block
+ * @cfg:		compatible configuration data
  * @completion:		end of single conversion completion
  * @buffer:		data buffer
  * @clk:		clock for this adc instance
@@ -149,10 +282,13 @@ struct stm32_adc_regs {
  * @rx_buf:		dma rx buffer cpu address
  * @rx_dma_buf:		dma rx buffer bus address
  * @rx_buf_sz:		dma rx buffer size
+ * @pcsel		bitmask to preselect channels on some devices
+ * @cal:		optional calibration data on some devices
  */
 struct stm32_adc {
 	struct stm32_adc_common	*common;
 	u32			offset;
+	const struct stm32_adc_cfg	*cfg;
 	struct completion	completion;
 	u16			buffer[STM32_ADC_MAX_SQ];
 	struct clk		*clk;
@@ -166,6 +302,8 @@ struct stm32_adc {
 	u8			*rx_buf;
 	dma_addr_t		rx_dma_buf;
 	unsigned int		rx_buf_sz;
+	u32			pcsel;
+	struct stm32_adc_calib	cal;
 };
 
 /**
@@ -180,8 +318,26 @@ struct stm32_adc_chan_spec {
 	const char		*name;
 };
 
-/* Input definitions common for all STM32F4 instances */
-static const struct stm32_adc_chan_spec stm32f4_adc123_channels[] = {
+/**
+ * struct stm32_adc_info - stm32 ADC, per instance config data
+ * @channels:		Reference to stm32 channels spec
+ * @max_channels:	Number of channels
+ * @resolutions:	available resolutions
+ * @num_res:		number of available resolutions
+ */
+struct stm32_adc_info {
+	const struct stm32_adc_chan_spec *channels;
+	int max_channels;
+	const unsigned int *resolutions;
+	const unsigned int num_res;
+};
+
+/*
+ * Input definitions common for all instances:
+ * stm32f4 can have up to 16 channels
+ * stm32h7 can have up to 20 channels
+ */
+static const struct stm32_adc_chan_spec stm32_adc_channels[] = {
 	{ IIO_VOLTAGE, 0, "in0" },
 	{ IIO_VOLTAGE, 1, "in1" },
 	{ IIO_VOLTAGE, 2, "in2" },
@@ -198,6 +354,10 @@ static const struct stm32_adc_chan_spec stm32f4_adc123_channels[] = {
 	{ IIO_VOLTAGE, 13, "in13" },
 	{ IIO_VOLTAGE, 14, "in14" },
 	{ IIO_VOLTAGE, 15, "in15" },
+	{ IIO_VOLTAGE, 16, "in16" },
+	{ IIO_VOLTAGE, 17, "in17" },
+	{ IIO_VOLTAGE, 18, "in18" },
+	{ IIO_VOLTAGE, 19, "in19" },
 };
 
 static const unsigned int stm32f4_adc_resolutions[] = {
@@ -205,6 +365,25 @@ static const unsigned int stm32f4_adc_resolutions[] = {
 	12, 10, 8, 6,
 };
 
+static const struct stm32_adc_info stm32f4_adc_info = {
+	.channels = stm32_adc_channels,
+	.max_channels = 16,
+	.resolutions = stm32f4_adc_resolutions,
+	.num_res = ARRAY_SIZE(stm32f4_adc_resolutions),
+};
+
+static const unsigned int stm32h7_adc_resolutions[] = {
+	/* sorted values so the index matches RES[2:0] in STM32H7_ADC_CFGR */
+	16, 14, 12, 10, 8,
+};
+
+static const struct stm32_adc_info stm32h7_adc_info = {
+	.channels = stm32_adc_channels,
+	.max_channels = 20,
+	.resolutions = stm32h7_adc_resolutions,
+	.num_res = ARRAY_SIZE(stm32h7_adc_resolutions),
+};
+
 /**
  * stm32f4_sq - describe regular sequence registers
  * - L: sequence len (register & bit field)
@@ -252,6 +431,69 @@ static struct stm32_adc_trig_info stm32f4_adc_trigs[] = {
 	{}, /* sentinel */
 };
 
+static const struct stm32_adc_regspec stm32f4_adc_regspec = {
+	.dr = STM32F4_ADC_DR,
+	.ier_eoc = { STM32F4_ADC_CR1, STM32F4_EOCIE },
+	.isr_eoc = { STM32F4_ADC_SR, STM32F4_EOC },
+	.sqr = stm32f4_sq,
+	.exten = { STM32F4_ADC_CR2, STM32F4_EXTEN_MASK, STM32F4_EXTEN_SHIFT },
+	.extsel = { STM32F4_ADC_CR2, STM32F4_EXTSEL_MASK,
+		    STM32F4_EXTSEL_SHIFT },
+	.res = { STM32F4_ADC_CR1, STM32F4_RES_MASK, STM32F4_RES_SHIFT },
+};
+
+static const struct stm32_adc_regs stm32h7_sq[STM32_ADC_MAX_SQ + 1] = {
+	/* L: len bit field description to be kept as first element */
+	{ STM32H7_ADC_SQR1, GENMASK(3, 0), 0 },
+	/* SQ1..SQ16 registers & bit fields (reg, mask, shift) */
+	{ STM32H7_ADC_SQR1, GENMASK(10, 6), 6 },
+	{ STM32H7_ADC_SQR1, GENMASK(16, 12), 12 },
+	{ STM32H7_ADC_SQR1, GENMASK(22, 18), 18 },
+	{ STM32H7_ADC_SQR1, GENMASK(28, 24), 24 },
+	{ STM32H7_ADC_SQR2, GENMASK(4, 0), 0 },
+	{ STM32H7_ADC_SQR2, GENMASK(10, 6), 6 },
+	{ STM32H7_ADC_SQR2, GENMASK(16, 12), 12 },
+	{ STM32H7_ADC_SQR2, GENMASK(22, 18), 18 },
+	{ STM32H7_ADC_SQR2, GENMASK(28, 24), 24 },
+	{ STM32H7_ADC_SQR3, GENMASK(4, 0), 0 },
+	{ STM32H7_ADC_SQR3, GENMASK(10, 6), 6 },
+	{ STM32H7_ADC_SQR3, GENMASK(16, 12), 12 },
+	{ STM32H7_ADC_SQR3, GENMASK(22, 18), 18 },
+	{ STM32H7_ADC_SQR3, GENMASK(28, 24), 24 },
+	{ STM32H7_ADC_SQR4, GENMASK(4, 0), 0 },
+	{ STM32H7_ADC_SQR4, GENMASK(10, 6), 6 },
+};
+
+/* STM32H7 external trigger sources for all instances */
+static struct stm32_adc_trig_info stm32h7_adc_trigs[] = {
+	{ TIM1_CH1, STM32_EXT0 },
+	{ TIM1_CH2, STM32_EXT1 },
+	{ TIM1_CH3, STM32_EXT2 },
+	{ TIM2_CH2, STM32_EXT3 },
+	{ TIM3_TRGO, STM32_EXT4 },
+	{ TIM4_CH4, STM32_EXT5 },
+	{ TIM8_TRGO, STM32_EXT7 },
+	{ TIM8_TRGO2, STM32_EXT8 },
+	{ TIM1_TRGO, STM32_EXT9 },
+	{ TIM1_TRGO2, STM32_EXT10 },
+	{ TIM2_TRGO, STM32_EXT11 },
+	{ TIM4_TRGO, STM32_EXT12 },
+	{ TIM6_TRGO, STM32_EXT13 },
+	{ TIM3_CH4, STM32_EXT15 },
+	{},
+};
+
+static const struct stm32_adc_regspec stm32h7_adc_regspec = {
+	.dr = STM32H7_ADC_DR,
+	.ier_eoc = { STM32H7_ADC_IER, STM32H7_EOCIE },
+	.isr_eoc = { STM32H7_ADC_ISR, STM32H7_EOC },
+	.sqr = stm32h7_sq,
+	.exten = { STM32H7_ADC_CFGR, STM32H7_EXTEN_MASK, STM32H7_EXTEN_SHIFT },
+	.extsel = { STM32H7_ADC_CFGR, STM32H7_EXTSEL_MASK,
+		    STM32H7_EXTSEL_SHIFT },
+	.res = { STM32H7_ADC_CFGR, STM32H7_RES_MASK, STM32H7_RES_SHIFT },
+};
+
 /**
  * STM32 ADC registers access routines
  * @adc: stm32 adc instance
@@ -265,6 +507,12 @@ static u32 stm32_adc_readl(struct stm32_adc *adc, u32 reg)
 	return readl_relaxed(adc->common->base + adc->offset + reg);
 }
 
+#define stm32_adc_readl_addr(addr)	stm32_adc_readl(adc, addr)
+
+#define stm32_adc_readl_poll_timeout(reg, val, cond, sleep_us, timeout_us) \
+	readx_poll_timeout(stm32_adc_readl_addr, reg, val, \
+			   cond, sleep_us, timeout_us)
+
 static u16 stm32_adc_readw(struct stm32_adc *adc, u32 reg)
 {
 	return readw_relaxed(adc->common->base + adc->offset + reg);
@@ -299,7 +547,8 @@ static void stm32_adc_clr_bits(struct stm32_adc *adc, u32 reg, u32 bits)
  */
 static void stm32_adc_conv_irq_enable(struct stm32_adc *adc)
 {
-	stm32_adc_set_bits(adc, STM32F4_ADC_CR1, STM32F4_EOCIE);
+	stm32_adc_set_bits(adc, adc->cfg->regs->ier_eoc.reg,
+			   adc->cfg->regs->ier_eoc.mask);
 };
 
 /**
@@ -308,19 +557,22 @@ static void stm32_adc_conv_irq_enable(struct stm32_adc *adc)
  */
 static void stm32_adc_conv_irq_disable(struct stm32_adc *adc)
 {
-	stm32_adc_clr_bits(adc, STM32F4_ADC_CR1, STM32F4_EOCIE);
+	stm32_adc_clr_bits(adc, adc->cfg->regs->ier_eoc.reg,
+			   adc->cfg->regs->ier_eoc.mask);
 }
 
 static void stm32_adc_set_res(struct stm32_adc *adc)
 {
-	u32 val = stm32_adc_readl(adc, STM32F4_ADC_CR1);
+	const struct stm32_adc_regs *res = &adc->cfg->regs->res;
+	u32 val;
 
-	val = (val & ~STM32F4_RES_MASK) | (adc->res << STM32F4_RES_SHIFT);
-	stm32_adc_writel(adc, STM32F4_ADC_CR1, val);
+	val = stm32_adc_readl(adc, res->reg);
+	val = (val & ~res->mask) | (adc->res << res->shift);
+	stm32_adc_writel(adc, res->reg, val);
 }
 
 /**
- * stm32_adc_start_conv() - Start conversions for regular channels.
+ * stm32f4_adc_start_conv() - Start conversions for regular channels.
  * @adc: stm32 adc instance
  * @dma: use dma to transfer conversion result
  *
@@ -329,7 +581,7 @@ static void stm32_adc_set_res(struct stm32_adc *adc)
  * conversions, in IIO buffer modes. Otherwise, use ADC interrupt with direct
  * DR read instead (e.g. read_raw, or triggered buffer mode without DMA).
  */
-static void stm32_adc_start_conv(struct stm32_adc *adc, bool dma)
+static void stm32f4_adc_start_conv(struct stm32_adc *adc, bool dma)
 {
 	stm32_adc_set_bits(adc, STM32F4_ADC_CR1, STM32F4_SCAN);
 
@@ -347,7 +599,7 @@ static void stm32_adc_start_conv(struct stm32_adc *adc, bool dma)
 		stm32_adc_set_bits(adc, STM32F4_ADC_CR2, STM32F4_SWSTART);
 }
 
-static void stm32_adc_stop_conv(struct stm32_adc *adc)
+static void stm32f4_adc_stop_conv(struct stm32_adc *adc)
 {
 	stm32_adc_clr_bits(adc, STM32F4_ADC_CR2, STM32F4_EXTEN_MASK);
 	stm32_adc_clr_bits(adc, STM32F4_ADC_SR, STM32F4_STRT);
@@ -357,6 +609,324 @@ static void stm32_adc_stop_conv(struct stm32_adc *adc)
 			   STM32F4_ADON | STM32F4_DMA | STM32F4_DDS);
 }
 
+static void stm32h7_adc_start_conv(struct stm32_adc *adc, bool dma)
+{
+	enum stm32h7_adc_dmngt dmngt;
+	unsigned long flags;
+	u32 val;
+
+	if (dma)
+		dmngt = STM32H7_DMNGT_DMA_CIRC;
+	else
+		dmngt = STM32H7_DMNGT_DR_ONLY;
+
+	spin_lock_irqsave(&adc->lock, flags);
+	val = stm32_adc_readl(adc, STM32H7_ADC_CFGR);
+	val = (val & ~STM32H7_DMNGT_MASK) | (dmngt << STM32H7_DMNGT_SHIFT);
+	stm32_adc_writel(adc, STM32H7_ADC_CFGR, val);
+	spin_unlock_irqrestore(&adc->lock, flags);
+
+	stm32_adc_set_bits(adc, STM32H7_ADC_CR, STM32H7_ADSTART);
+}
+
+static void stm32h7_adc_stop_conv(struct stm32_adc *adc)
+{
+	struct iio_dev *indio_dev = iio_priv_to_dev(adc);
+	int ret;
+	u32 val;
+
+	stm32_adc_set_bits(adc, STM32H7_ADC_CR, STM32H7_ADSTP);
+
+	ret = stm32_adc_readl_poll_timeout(STM32H7_ADC_CR, val,
+					   !(val & (STM32H7_ADSTART)),
+					   100, STM32_ADC_TIMEOUT_US);
+	if (ret)
+		dev_warn(&indio_dev->dev, "stop failed\n");
+
+	stm32_adc_clr_bits(adc, STM32H7_ADC_CFGR, STM32H7_DMNGT_MASK);
+}
+
+static void stm32h7_adc_exit_pwr_down(struct stm32_adc *adc)
+{
+	/* Exit deep power down, then enable ADC voltage regulator */
+	stm32_adc_clr_bits(adc, STM32H7_ADC_CR, STM32H7_DEEPPWD);
+	stm32_adc_set_bits(adc, STM32H7_ADC_CR, STM32H7_ADVREGEN);
+
+	if (adc->common->rate > STM32H7_BOOST_CLKRATE)
+		stm32_adc_set_bits(adc, STM32H7_ADC_CR, STM32H7_BOOST);
+
+	/* Wait for startup time */
+	usleep_range(10, 20);
+}
+
+static void stm32h7_adc_enter_pwr_down(struct stm32_adc *adc)
+{
+	stm32_adc_clr_bits(adc, STM32H7_ADC_CR, STM32H7_BOOST);
+
+	/* Setting DEEPPWD disables ADC vreg and clears ADVREGEN */
+	stm32_adc_set_bits(adc, STM32H7_ADC_CR, STM32H7_DEEPPWD);
+}
+
+static int stm32h7_adc_enable(struct stm32_adc *adc)
+{
+	struct iio_dev *indio_dev = iio_priv_to_dev(adc);
+	int ret;
+	u32 val;
+
+	/* Clear ADRDY by writing one, then enable ADC */
+	stm32_adc_set_bits(adc, STM32H7_ADC_ISR, STM32H7_ADRDY);
+	stm32_adc_set_bits(adc, STM32H7_ADC_CR, STM32H7_ADEN);
+
+	/* Poll for ADRDY to be set (after adc startup time) */
+	ret = stm32_adc_readl_poll_timeout(STM32H7_ADC_ISR, val,
+					   val & STM32H7_ADRDY,
+					   100, STM32_ADC_TIMEOUT_US);
+	if (ret) {
+		stm32_adc_clr_bits(adc, STM32H7_ADC_CR, STM32H7_ADEN);
+		dev_err(&indio_dev->dev, "Failed to enable ADC\n");
+	}
+
+	return ret;
+}
+
+static void stm32h7_adc_disable(struct stm32_adc *adc)
+{
+	struct iio_dev *indio_dev = iio_priv_to_dev(adc);
+	int ret;
+	u32 val;
+
+	/* Disable ADC and wait until it's effectively disabled */
+	stm32_adc_set_bits(adc, STM32H7_ADC_CR, STM32H7_ADDIS);
+	ret = stm32_adc_readl_poll_timeout(STM32H7_ADC_CR, val,
+					   !(val & STM32H7_ADEN), 100,
+					   STM32_ADC_TIMEOUT_US);
+	if (ret)
+		dev_warn(&indio_dev->dev, "Failed to disable\n");
+}
+
+/**
+ * stm32h7_adc_read_selfcalib() - read calibration shadow regs, save result
+ * @adc: stm32 adc instance
+ */
+static int stm32h7_adc_read_selfcalib(struct stm32_adc *adc)
+{
+	struct iio_dev *indio_dev = iio_priv_to_dev(adc);
+	int i, ret;
+	u32 lincalrdyw_mask, val;
+
+	/* Enable adc so LINCALRDYW1..6 bits are writable */
+	ret = stm32h7_adc_enable(adc);
+	if (ret)
+		return ret;
+
+	/* Read linearity calibration */
+	lincalrdyw_mask = STM32H7_LINCALRDYW6;
+	for (i = STM32H7_LINCALFACT_NUM - 1; i >= 0; i--) {
+		/* Clear STM32H7_LINCALRDYW[6..1]: transfer calib to CALFACT2 */
+		stm32_adc_clr_bits(adc, STM32H7_ADC_CR, lincalrdyw_mask);
+
+		/* Poll: wait calib data to be ready in CALFACT2 register */
+		ret = stm32_adc_readl_poll_timeout(STM32H7_ADC_CR, val,
+						   !(val & lincalrdyw_mask),
+						   100, STM32_ADC_TIMEOUT_US);
+		if (ret) {
+			dev_err(&indio_dev->dev, "Failed to read calfact\n");
+			goto disable;
+		}
+
+		val = stm32_adc_readl(adc, STM32H7_ADC_CALFACT2);
+		adc->cal.lincalfact[i] = (val & STM32H7_LINCALFACT_MASK);
+		adc->cal.lincalfact[i] >>= STM32H7_LINCALFACT_SHIFT;
+
+		lincalrdyw_mask >>= 1;
+	}
+
+	/* Read offset calibration */
+	val = stm32_adc_readl(adc, STM32H7_ADC_CALFACT);
+	adc->cal.calfact_s = (val & STM32H7_CALFACT_S_MASK);
+	adc->cal.calfact_s >>= STM32H7_CALFACT_S_SHIFT;
+	adc->cal.calfact_d = (val & STM32H7_CALFACT_D_MASK);
+	adc->cal.calfact_d >>= STM32H7_CALFACT_D_SHIFT;
+
+disable:
+	stm32h7_adc_disable(adc);
+
+	return ret;
+}
+
+/**
+ * stm32h7_adc_restore_selfcalib() - Restore saved self-calibration result
+ * @adc: stm32 adc instance
+ * Note: ADC must be enabled, with no on-going conversions.
+ */
+static int stm32h7_adc_restore_selfcalib(struct stm32_adc *adc)
+{
+	struct iio_dev *indio_dev = iio_priv_to_dev(adc);
+	int i, ret;
+	u32 lincalrdyw_mask, val;
+
+	val = (adc->cal.calfact_s << STM32H7_CALFACT_S_SHIFT) |
+		(adc->cal.calfact_d << STM32H7_CALFACT_D_SHIFT);
+	stm32_adc_writel(adc, STM32H7_ADC_CALFACT, val);
+
+	lincalrdyw_mask = STM32H7_LINCALRDYW6;
+	for (i = STM32H7_LINCALFACT_NUM - 1; i >= 0; i--) {
+		/*
+		 * Write saved calibration data to shadow registers:
+		 * Write CALFACT2, and set LINCALRDYW[6..1] bit to trigger
+		 * data write. Then poll to wait for complete transfer.
+		 */
+		val = adc->cal.lincalfact[i] << STM32H7_LINCALFACT_SHIFT;
+		stm32_adc_writel(adc, STM32H7_ADC_CALFACT2, val);
+		stm32_adc_set_bits(adc, STM32H7_ADC_CR, lincalrdyw_mask);
+		ret = stm32_adc_readl_poll_timeout(STM32H7_ADC_CR, val,
+						   val & lincalrdyw_mask,
+						   100, STM32_ADC_TIMEOUT_US);
+		if (ret) {
+			dev_err(&indio_dev->dev, "Failed to write calfact\n");
+			return ret;
+		}
+
+		/*
+		 * Read back calibration data, has two effects:
+		 * - It ensures bits LINCALRDYW[6..1] are kept cleared
+		 *   for next time calibration needs to be restored.
+		 * - BTW, bit clear triggers a read, then check data has been
+		 *   correctly written.
+		 */
+		stm32_adc_clr_bits(adc, STM32H7_ADC_CR, lincalrdyw_mask);
+		ret = stm32_adc_readl_poll_timeout(STM32H7_ADC_CR, val,
+						   !(val & lincalrdyw_mask),
+						   100, STM32_ADC_TIMEOUT_US);
+		if (ret) {
+			dev_err(&indio_dev->dev, "Failed to read calfact\n");
+			return ret;
+		}
+		val = stm32_adc_readl(adc, STM32H7_ADC_CALFACT2);
+		if (val != adc->cal.lincalfact[i] << STM32H7_LINCALFACT_SHIFT) {
+			dev_err(&indio_dev->dev, "calfact not consistent\n");
+			return -EIO;
+		}
+
+		lincalrdyw_mask >>= 1;
+	}
+
+	return 0;
+}
+
+/**
+ * Fixed timeout value for ADC calibration.
+ * worst cases:
+ * - low clock frequency
+ * - maximum prescalers
+ * Calibration requires:
+ * - 131,072 ADC clock cycle for the linear calibration
+ * - 20 ADC clock cycle for the offset calibration
+ *
+ * Set to 100ms for now
+ */
+#define STM32H7_ADC_CALIB_TIMEOUT_US		100000
+
+/**
+ * stm32h7_adc_selfcalib() - Procedure to calibrate ADC (from power down)
+ * @adc: stm32 adc instance
+ * Exit from power down, calibrate ADC, then return to power down.
+ */
+static int stm32h7_adc_selfcalib(struct stm32_adc *adc)
+{
+	struct iio_dev *indio_dev = iio_priv_to_dev(adc);
+	int ret;
+	u32 val;
+
+	stm32h7_adc_exit_pwr_down(adc);
+
+	/*
+	 * Select calibration mode:
+	 * - Offset calibration for single ended inputs
+	 * - No linearity calibration (do it later, before reading it)
+	 */
+	stm32_adc_clr_bits(adc, STM32H7_ADC_CR, STM32H7_ADCALDIF);
+	stm32_adc_clr_bits(adc, STM32H7_ADC_CR, STM32H7_ADCALLIN);
+
+	/* Start calibration, then wait for completion */
+	stm32_adc_set_bits(adc, STM32H7_ADC_CR, STM32H7_ADCAL);
+	ret = stm32_adc_readl_poll_timeout(STM32H7_ADC_CR, val,
+					   !(val & STM32H7_ADCAL), 100,
+					   STM32H7_ADC_CALIB_TIMEOUT_US);
+	if (ret) {
+		dev_err(&indio_dev->dev, "calibration failed\n");
+		goto pwr_dwn;
+	}
+
+	/*
+	 * Select calibration mode, then start calibration:
+	 * - Offset calibration for differential input
+	 * - Linearity calibration (needs to be done only once for single/diff)
+	 *   will run simultaneously with offset calibration.
+	 */
+	stm32_adc_set_bits(adc, STM32H7_ADC_CR,
+			   STM32H7_ADCALDIF | STM32H7_ADCALLIN);
+	stm32_adc_set_bits(adc, STM32H7_ADC_CR, STM32H7_ADCAL);
+	ret = stm32_adc_readl_poll_timeout(STM32H7_ADC_CR, val,
+					   !(val & STM32H7_ADCAL), 100,
+					   STM32H7_ADC_CALIB_TIMEOUT_US);
+	if (ret) {
+		dev_err(&indio_dev->dev, "calibration failed\n");
+		goto pwr_dwn;
+	}
+
+	stm32_adc_clr_bits(adc, STM32H7_ADC_CR,
+			   STM32H7_ADCALDIF | STM32H7_ADCALLIN);
+
+	/* Read calibration result for future reference */
+	ret = stm32h7_adc_read_selfcalib(adc);
+
+pwr_dwn:
+	stm32h7_adc_enter_pwr_down(adc);
+
+	return ret;
+}
+
+/**
+ * stm32h7_adc_prepare() - Leave power down mode to enable ADC.
+ * @adc: stm32 adc instance
+ * Leave power down mode.
+ * Enable ADC.
+ * Restore calibration data.
+ * Pre-select channels that may be used in PCSEL (required by input MUX / IO).
+ */
+static int stm32h7_adc_prepare(struct stm32_adc *adc)
+{
+	int ret;
+
+	stm32h7_adc_exit_pwr_down(adc);
+
+	ret = stm32h7_adc_enable(adc);
+	if (ret)
+		goto pwr_dwn;
+
+	ret = stm32h7_adc_restore_selfcalib(adc);
+	if (ret)
+		goto disable;
+
+	stm32_adc_writel(adc, STM32H7_ADC_PCSEL, adc->pcsel);
+
+	return 0;
+
+disable:
+	stm32h7_adc_disable(adc);
+pwr_dwn:
+	stm32h7_adc_enter_pwr_down(adc);
+
+	return ret;
+}
+
+static void stm32h7_adc_unprepare(struct stm32_adc *adc)
+{
+	stm32h7_adc_disable(adc);
+	stm32h7_adc_enter_pwr_down(adc);
+}
+
 /**
  * stm32_adc_conf_scan_seq() - Build regular channels scan sequence
  * @indio_dev: IIO device
@@ -371,6 +941,7 @@ static int stm32_adc_conf_scan_seq(struct iio_dev *indio_dev,
 				   const unsigned long *scan_mask)
 {
 	struct stm32_adc *adc = iio_priv(indio_dev);
+	const struct stm32_adc_regs *sqr = adc->cfg->regs->sqr;
 	const struct iio_chan_spec *chan;
 	u32 val, bit;
 	int i = 0;
@@ -388,20 +959,20 @@ static int stm32_adc_conf_scan_seq(struct iio_dev *indio_dev,
 		dev_dbg(&indio_dev->dev, "%s chan %d to SQ%d\n",
 			__func__, chan->channel, i);
 
-		val = stm32_adc_readl(adc, stm32f4_sq[i].reg);
-		val &= ~stm32f4_sq[i].mask;
-		val |= chan->channel << stm32f4_sq[i].shift;
-		stm32_adc_writel(adc, stm32f4_sq[i].reg, val);
+		val = stm32_adc_readl(adc, sqr[i].reg);
+		val &= ~sqr[i].mask;
+		val |= chan->channel << sqr[i].shift;
+		stm32_adc_writel(adc, sqr[i].reg, val);
 	}
 
 	if (!i)
 		return -EINVAL;
 
 	/* Sequence len */
-	val = stm32_adc_readl(adc, stm32f4_sq[0].reg);
-	val &= ~stm32f4_sq[0].mask;
-	val |= ((i - 1) << stm32f4_sq[0].shift);
-	stm32_adc_writel(adc, stm32f4_sq[0].reg, val);
+	val = stm32_adc_readl(adc, sqr[0].reg);
+	val &= ~sqr[0].mask;
+	val |= ((i - 1) << sqr[0].shift);
+	stm32_adc_writel(adc, sqr[0].reg, val);
 
 	return 0;
 }
@@ -412,19 +983,21 @@ static int stm32_adc_conf_scan_seq(struct iio_dev *indio_dev,
  *
  * Returns trigger extsel value, if trig matches, -EINVAL otherwise.
  */
-static int stm32_adc_get_trig_extsel(struct iio_trigger *trig)
+static int stm32_adc_get_trig_extsel(struct iio_dev *indio_dev,
+				     struct iio_trigger *trig)
 {
+	struct stm32_adc *adc = iio_priv(indio_dev);
 	int i;
 
 	/* lookup triggers registered by stm32 timer trigger driver */
-	for (i = 0; stm32f4_adc_trigs[i].name; i++) {
+	for (i = 0; adc->cfg->trigs[i].name; i++) {
 		/**
 		 * Checking both stm32 timer trigger type and trig name
 		 * should be safe against arbitrary trigger names.
 		 */
 		if (is_stm32_timer_trigger(trig) &&
-		    !strcmp(stm32f4_adc_trigs[i].name, trig->name)) {
-			return stm32f4_adc_trigs[i].extsel;
+		    !strcmp(adc->cfg->trigs[i].name, trig->name)) {
+			return adc->cfg->trigs[i].extsel;
 		}
 	}
 
@@ -449,7 +1022,7 @@ static int stm32_adc_set_trig(struct iio_dev *indio_dev,
 	int ret;
 
 	if (trig) {
-		ret = stm32_adc_get_trig_extsel(trig);
+		ret = stm32_adc_get_trig_extsel(indio_dev, trig);
 		if (ret < 0)
 			return ret;
 
@@ -459,11 +1032,11 @@ static int stm32_adc_set_trig(struct iio_dev *indio_dev,
 	}
 
 	spin_lock_irqsave(&adc->lock, flags);
-	val = stm32_adc_readl(adc, STM32F4_ADC_CR2);
-	val &= ~(STM32F4_EXTEN_MASK | STM32F4_EXTSEL_MASK);
-	val |= exten << STM32F4_EXTEN_SHIFT;
-	val |= extsel << STM32F4_EXTSEL_SHIFT;
-	stm32_adc_writel(adc, STM32F4_ADC_CR2, val);
+	val = stm32_adc_readl(adc, adc->cfg->regs->exten.reg);
+	val &= ~(adc->cfg->regs->exten.mask | adc->cfg->regs->extsel.mask);
+	val |= exten << adc->cfg->regs->exten.shift;
+	val |= extsel << adc->cfg->regs->extsel.shift;
+	stm32_adc_writel(adc,  adc->cfg->regs->exten.reg, val);
 	spin_unlock_irqrestore(&adc->lock, flags);
 
 	return 0;
@@ -515,6 +1088,7 @@ static int stm32_adc_single_conv(struct iio_dev *indio_dev,
 				 int *res)
 {
 	struct stm32_adc *adc = iio_priv(indio_dev);
+	const struct stm32_adc_regspec *regs = adc->cfg->regs;
 	long timeout;
 	u32 val;
 	int ret;
@@ -523,21 +1097,27 @@ static int stm32_adc_single_conv(struct iio_dev *indio_dev,
 
 	adc->bufi = 0;
 
+	if (adc->cfg->prepare) {
+		ret = adc->cfg->prepare(adc);
+		if (ret)
+			return ret;
+	}
+
 	/* Program chan number in regular sequence (SQ1) */
-	val = stm32_adc_readl(adc, stm32f4_sq[1].reg);
-	val &= ~stm32f4_sq[1].mask;
-	val |= chan->channel << stm32f4_sq[1].shift;
-	stm32_adc_writel(adc, stm32f4_sq[1].reg, val);
+	val = stm32_adc_readl(adc, regs->sqr[1].reg);
+	val &= ~regs->sqr[1].mask;
+	val |= chan->channel << regs->sqr[1].shift;
+	stm32_adc_writel(adc, regs->sqr[1].reg, val);
 
 	/* Set regular sequence len (0 for 1 conversion) */
-	stm32_adc_clr_bits(adc, stm32f4_sq[0].reg, stm32f4_sq[0].mask);
+	stm32_adc_clr_bits(adc, regs->sqr[0].reg, regs->sqr[0].mask);
 
 	/* Trigger detection disabled (conversion can be launched in SW) */
-	stm32_adc_clr_bits(adc, STM32F4_ADC_CR2, STM32F4_EXTEN_MASK);
+	stm32_adc_clr_bits(adc, regs->exten.reg, regs->exten.mask);
 
 	stm32_adc_conv_irq_enable(adc);
 
-	stm32_adc_start_conv(adc, false);
+	adc->cfg->start_conv(adc, false);
 
 	timeout = wait_for_completion_interruptible_timeout(
 					&adc->completion, STM32_ADC_TIMEOUT);
@@ -550,10 +1130,13 @@ static int stm32_adc_single_conv(struct iio_dev *indio_dev,
 		ret = IIO_VAL_INT;
 	}
 
-	stm32_adc_stop_conv(adc);
+	adc->cfg->stop_conv(adc);
 
 	stm32_adc_conv_irq_disable(adc);
 
+	if (adc->cfg->unprepare)
+		adc->cfg->unprepare(adc);
+
 	return ret;
 }
 
@@ -590,11 +1173,12 @@ static irqreturn_t stm32_adc_isr(int irq, void *data)
 {
 	struct stm32_adc *adc = data;
 	struct iio_dev *indio_dev = iio_priv_to_dev(adc);
-	u32 status = stm32_adc_readl(adc, STM32F4_ADC_SR);
+	const struct stm32_adc_regspec *regs = adc->cfg->regs;
+	u32 status = stm32_adc_readl(adc, regs->isr_eoc.reg);
 
-	if (status & STM32F4_EOC) {
+	if (status & regs->isr_eoc.mask) {
 		/* Reading DR also clears EOC status flag */
-		adc->buffer[adc->bufi] = stm32_adc_readw(adc, STM32F4_ADC_DR);
+		adc->buffer[adc->bufi] = stm32_adc_readw(adc, regs->dr);
 		if (iio_buffer_enabled(indio_dev)) {
 			adc->bufi++;
 			if (adc->bufi >= adc->num_conv) {
@@ -621,7 +1205,7 @@ static irqreturn_t stm32_adc_isr(int irq, void *data)
 static int stm32_adc_validate_trigger(struct iio_dev *indio_dev,
 				      struct iio_trigger *trig)
 {
-	return stm32_adc_get_trig_extsel(trig) < 0 ? -EINVAL : 0;
+	return stm32_adc_get_trig_extsel(indio_dev, trig) < 0 ? -EINVAL : 0;
 }
 
 static int stm32_adc_set_watermark(struct iio_dev *indio_dev, unsigned int val)
@@ -777,10 +1361,16 @@ static int stm32_adc_buffer_postenable(struct iio_dev *indio_dev)
 	struct stm32_adc *adc = iio_priv(indio_dev);
 	int ret;
 
+	if (adc->cfg->prepare) {
+		ret = adc->cfg->prepare(adc);
+		if (ret)
+			return ret;
+	}
+
 	ret = stm32_adc_set_trig(indio_dev, indio_dev->trig);
 	if (ret) {
 		dev_err(&indio_dev->dev, "Can't set trigger\n");
-		return ret;
+		goto err_unprepare;
 	}
 
 	ret = stm32_adc_dma_start(indio_dev);
@@ -799,7 +1389,7 @@ static int stm32_adc_buffer_postenable(struct iio_dev *indio_dev)
 	if (!adc->dma_chan)
 		stm32_adc_conv_irq_enable(adc);
 
-	stm32_adc_start_conv(adc, !!adc->dma_chan);
+	adc->cfg->start_conv(adc, !!adc->dma_chan);
 
 	return 0;
 
@@ -808,6 +1398,9 @@ err_stop_dma:
 		dmaengine_terminate_all(adc->dma_chan);
 err_clr_trig:
 	stm32_adc_set_trig(indio_dev, NULL);
+err_unprepare:
+	if (adc->cfg->unprepare)
+		adc->cfg->unprepare(adc);
 
 	return ret;
 }
@@ -817,7 +1410,7 @@ static int stm32_adc_buffer_predisable(struct iio_dev *indio_dev)
 	struct stm32_adc *adc = iio_priv(indio_dev);
 	int ret;
 
-	stm32_adc_stop_conv(adc);
+	adc->cfg->stop_conv(adc);
 	if (!adc->dma_chan)
 		stm32_adc_conv_irq_disable(adc);
 
@@ -831,6 +1424,9 @@ static int stm32_adc_buffer_predisable(struct iio_dev *indio_dev)
 	if (stm32_adc_set_trig(indio_dev, NULL))
 		dev_err(&indio_dev->dev, "Can't clear trigger\n");
 
+	if (adc->cfg->unprepare)
+		adc->cfg->unprepare(adc);
+
 	return ret;
 }
 
@@ -895,12 +1491,12 @@ static int stm32_adc_of_get_resolution(struct iio_dev *indio_dev)
 	u32 res;
 
 	if (of_property_read_u32(node, "assigned-resolution-bits", &res))
-		res = stm32f4_adc_resolutions[0];
+		res = adc->cfg->adc_info->resolutions[0];
 
-	for (i = 0; i < ARRAY_SIZE(stm32f4_adc_resolutions); i++)
-		if (res == stm32f4_adc_resolutions[i])
+	for (i = 0; i < adc->cfg->adc_info->num_res; i++)
+		if (res == adc->cfg->adc_info->resolutions[i])
 			break;
-	if (i >= ARRAY_SIZE(stm32f4_adc_resolutions)) {
+	if (i >= adc->cfg->adc_info->num_res) {
 		dev_err(&indio_dev->dev, "Bad resolution: %u bits\n", res);
 		return -EINVAL;
 	}
@@ -926,14 +1522,19 @@ static void stm32_adc_chan_init_one(struct iio_dev *indio_dev,
 	chan->info_mask_separate = BIT(IIO_CHAN_INFO_RAW);
 	chan->info_mask_shared_by_type = BIT(IIO_CHAN_INFO_SCALE);
 	chan->scan_type.sign = 'u';
-	chan->scan_type.realbits = stm32f4_adc_resolutions[adc->res];
+	chan->scan_type.realbits = adc->cfg->adc_info->resolutions[adc->res];
 	chan->scan_type.storagebits = 16;
 	chan->ext_info = stm32_adc_ext_info;
+
+	/* pre-build selected channels mask */
+	adc->pcsel |= BIT(chan->channel);
 }
 
 static int stm32_adc_chan_of_init(struct iio_dev *indio_dev)
 {
 	struct device_node *node = indio_dev->dev.of_node;
+	struct stm32_adc *adc = iio_priv(indio_dev);
+	const struct stm32_adc_info *adc_info = adc->cfg->adc_info;
 	struct property *prop;
 	const __be32 *cur;
 	struct iio_chan_spec *channels;
@@ -942,7 +1543,7 @@ static int stm32_adc_chan_of_init(struct iio_dev *indio_dev)
 
 	num_channels = of_property_count_u32_elems(node, "st,adc-channels");
 	if (num_channels < 0 ||
-	    num_channels >= ARRAY_SIZE(stm32f4_adc123_channels)) {
+	    num_channels >= adc_info->max_channels) {
 		dev_err(&indio_dev->dev, "Bad st,adc-channels?\n");
 		return num_channels < 0 ? num_channels : -EINVAL;
 	}
@@ -953,12 +1554,12 @@ static int stm32_adc_chan_of_init(struct iio_dev *indio_dev)
 		return -ENOMEM;
 
 	of_property_for_each_u32(node, "st,adc-channels", prop, cur, val) {
-		if (val >= ARRAY_SIZE(stm32f4_adc123_channels)) {
+		if (val >= adc_info->max_channels) {
 			dev_err(&indio_dev->dev, "Invalid channel %d\n", val);
 			return -EINVAL;
 		}
 		stm32_adc_chan_init_one(indio_dev, &channels[scan_index],
-					&stm32f4_adc123_channels[val],
+					&adc_info->channels[val],
 					scan_index);
 		scan_index++;
 	}
@@ -990,7 +1591,7 @@ static int stm32_adc_dma_request(struct iio_dev *indio_dev)
 	/* Configure DMA channel to read data register */
 	memset(&config, 0, sizeof(config));
 	config.src_addr = (dma_addr_t)adc->common->phys_base;
-	config.src_addr += adc->offset + STM32F4_ADC_DR;
+	config.src_addr += adc->offset + adc->cfg->regs->dr;
 	config.src_addr_width = DMA_SLAVE_BUSWIDTH_2_BYTES;
 
 	ret = dmaengine_slave_config(adc->dma_chan, &config);
@@ -1011,6 +1612,7 @@ err_release:
 static int stm32_adc_probe(struct platform_device *pdev)
 {
 	struct iio_dev *indio_dev;
+	struct device *dev = &pdev->dev;
 	struct stm32_adc *adc;
 	int ret;
 
@@ -1025,6 +1627,8 @@ static int stm32_adc_probe(struct platform_device *pdev)
 	adc->common = dev_get_drvdata(pdev->dev.parent);
 	spin_lock_init(&adc->lock);
 	init_completion(&adc->completion);
+	adc->cfg = (const struct stm32_adc_cfg *)
+		of_match_device(dev->driver->of_match_table, dev)->data;
 
 	indio_dev->name = dev_name(&pdev->dev);
 	indio_dev->dev.parent = &pdev->dev;
@@ -1055,14 +1659,21 @@ static int stm32_adc_probe(struct platform_device *pdev)
 
 	adc->clk = devm_clk_get(&pdev->dev, NULL);
 	if (IS_ERR(adc->clk)) {
-		dev_err(&pdev->dev, "Can't get clock\n");
-		return PTR_ERR(adc->clk);
+		ret = PTR_ERR(adc->clk);
+		if (ret == -ENOENT && !adc->cfg->clk_required) {
+			adc->clk = NULL;
+		} else {
+			dev_err(&pdev->dev, "Can't get clock\n");
+			return ret;
+		}
 	}
 
-	ret = clk_prepare_enable(adc->clk);
-	if (ret < 0) {
-		dev_err(&pdev->dev, "clk enable failed\n");
-		return ret;
+	if (adc->clk) {
+		ret = clk_prepare_enable(adc->clk);
+		if (ret < 0) {
+			dev_err(&pdev->dev, "clk enable failed\n");
+			return ret;
+		}
 	}
 
 	ret = stm32_adc_of_get_resolution(indio_dev);
@@ -1070,6 +1681,12 @@ static int stm32_adc_probe(struct platform_device *pdev)
 		goto err_clk_disable;
 	stm32_adc_set_res(adc);
 
+	if (adc->cfg->selfcalib) {
+		ret = adc->cfg->selfcalib(adc);
+		if (ret)
+			goto err_clk_disable;
+	}
+
 	ret = stm32_adc_chan_of_init(indio_dev);
 	if (ret < 0)
 		goto err_clk_disable;
@@ -1106,7 +1723,8 @@ err_dma_disable:
 		dma_release_channel(adc->dma_chan);
 	}
 err_clk_disable:
-	clk_disable_unprepare(adc->clk);
+	if (adc->clk)
+		clk_disable_unprepare(adc->clk);
 
 	return ret;
 }
@@ -1124,13 +1742,35 @@ static int stm32_adc_remove(struct platform_device *pdev)
 				  adc->rx_buf, adc->rx_dma_buf);
 		dma_release_channel(adc->dma_chan);
 	}
-	clk_disable_unprepare(adc->clk);
+	if (adc->clk)
+		clk_disable_unprepare(adc->clk);
 
 	return 0;
 }
 
+static const struct stm32_adc_cfg stm32f4_adc_cfg = {
+	.regs = &stm32f4_adc_regspec,
+	.adc_info = &stm32f4_adc_info,
+	.trigs = stm32f4_adc_trigs,
+	.clk_required = true,
+	.start_conv = stm32f4_adc_start_conv,
+	.stop_conv = stm32f4_adc_stop_conv,
+};
+
+static const struct stm32_adc_cfg stm32h7_adc_cfg = {
+	.regs = &stm32h7_adc_regspec,
+	.adc_info = &stm32h7_adc_info,
+	.trigs = stm32h7_adc_trigs,
+	.selfcalib = stm32h7_adc_selfcalib,
+	.start_conv = stm32h7_adc_start_conv,
+	.stop_conv = stm32h7_adc_stop_conv,
+	.prepare = stm32h7_adc_prepare,
+	.unprepare = stm32h7_adc_unprepare,
+};
+
 static const struct of_device_id stm32_adc_of_match[] = {
-	{ .compatible = "st,stm32f4-adc" },
+	{ .compatible = "st,stm32f4-adc", .data = (void *)&stm32f4_adc_cfg },
+	{ .compatible = "st,stm32h7-adc", .data = (void *)&stm32h7_adc_cfg },
 	{},
 };
 MODULE_DEVICE_TABLE(of, stm32_adc_of_match);
diff --git a/drivers/iio/adc/twl4030-madc.c b/drivers/iio/adc/twl4030-madc.c
index 0c74869a540a..bd3d37fc2144 100644
--- a/drivers/iio/adc/twl4030-madc.c
+++ b/drivers/iio/adc/twl4030-madc.c
@@ -36,7 +36,6 @@
 #include <linux/platform_device.h>
 #include <linux/slab.h>
 #include <linux/i2c/twl.h>
-#include <linux/i2c/twl4030-madc.h>
 #include <linux/module.h>
 #include <linux/stddef.h>
 #include <linux/mutex.h>
@@ -49,9 +48,121 @@
 
 #include <linux/iio/iio.h>
 
+#define TWL4030_MADC_MAX_CHANNELS 16
+
+#define TWL4030_MADC_CTRL1		0x00
+#define TWL4030_MADC_CTRL2		0x01
+
+#define TWL4030_MADC_RTSELECT_LSB	0x02
+#define TWL4030_MADC_SW1SELECT_LSB	0x06
+#define TWL4030_MADC_SW2SELECT_LSB	0x0A
+
+#define TWL4030_MADC_RTAVERAGE_LSB	0x04
+#define TWL4030_MADC_SW1AVERAGE_LSB	0x08
+#define TWL4030_MADC_SW2AVERAGE_LSB	0x0C
+
+#define TWL4030_MADC_CTRL_SW1		0x12
+#define TWL4030_MADC_CTRL_SW2		0x13
+
+#define TWL4030_MADC_RTCH0_LSB		0x17
+#define TWL4030_MADC_GPCH0_LSB		0x37
+
+#define TWL4030_MADC_MADCON	(1 << 0)	/* MADC power on */
+#define TWL4030_MADC_BUSY	(1 << 0)	/* MADC busy */
+/* MADC conversion completion */
+#define TWL4030_MADC_EOC_SW	(1 << 1)
+/* MADC SWx start conversion */
+#define TWL4030_MADC_SW_START	(1 << 5)
+#define TWL4030_MADC_ADCIN0	(1 << 0)
+#define TWL4030_MADC_ADCIN1	(1 << 1)
+#define TWL4030_MADC_ADCIN2	(1 << 2)
+#define TWL4030_MADC_ADCIN3	(1 << 3)
+#define TWL4030_MADC_ADCIN4	(1 << 4)
+#define TWL4030_MADC_ADCIN5	(1 << 5)
+#define TWL4030_MADC_ADCIN6	(1 << 6)
+#define TWL4030_MADC_ADCIN7	(1 << 7)
+#define TWL4030_MADC_ADCIN8	(1 << 8)
+#define TWL4030_MADC_ADCIN9	(1 << 9)
+#define TWL4030_MADC_ADCIN10	(1 << 10)
+#define TWL4030_MADC_ADCIN11	(1 << 11)
+#define TWL4030_MADC_ADCIN12	(1 << 12)
+#define TWL4030_MADC_ADCIN13	(1 << 13)
+#define TWL4030_MADC_ADCIN14	(1 << 14)
+#define TWL4030_MADC_ADCIN15	(1 << 15)
+
+/* Fixed channels */
+#define TWL4030_MADC_BTEMP	TWL4030_MADC_ADCIN1
+#define TWL4030_MADC_VBUS	TWL4030_MADC_ADCIN8
+#define TWL4030_MADC_VBKB	TWL4030_MADC_ADCIN9
+#define TWL4030_MADC_ICHG	TWL4030_MADC_ADCIN10
+#define TWL4030_MADC_VCHG	TWL4030_MADC_ADCIN11
+#define TWL4030_MADC_VBAT	TWL4030_MADC_ADCIN12
+
+/* Step size and prescaler ratio */
+#define TEMP_STEP_SIZE          147
+#define TEMP_PSR_R              100
+#define CURR_STEP_SIZE		147
+#define CURR_PSR_R1		44
+#define CURR_PSR_R2		88
+
+#define TWL4030_BCI_BCICTL1	0x23
+#define TWL4030_BCI_CGAIN	0x020
+#define TWL4030_BCI_MESBAT	(1 << 1)
+#define TWL4030_BCI_TYPEN	(1 << 4)
+#define TWL4030_BCI_ITHEN	(1 << 3)
+
+#define REG_BCICTL2             0x024
+#define TWL4030_BCI_ITHSENS	0x007
+
+/* Register and bits for GPBR1 register */
+#define TWL4030_REG_GPBR1		0x0c
+#define TWL4030_GPBR1_MADC_HFCLK_EN	(1 << 7)
+
 #define TWL4030_USB_SEL_MADC_MCPC	(1<<3)
 #define TWL4030_USB_CARKIT_ANA_CTRL	0xBB
 
+struct twl4030_madc_conversion_method {
+	u8 sel;
+	u8 avg;
+	u8 rbase;
+	u8 ctrl;
+};
+
+/**
+ * struct twl4030_madc_request - madc request packet for channel conversion
+ * @channels:	16 bit bitmap for individual channels
+ * @do_avg:	sample the input channel for 4 consecutive cycles
+ * @method:	RT, SW1, SW2
+ * @type:	Polling or interrupt based method
+ * @active:	Flag if request is active
+ * @result_pending: Flag from irq handler, that result is ready
+ * @raw:	Return raw value, do not convert it
+ * @rbuf:	Result buffer
+ */
+struct twl4030_madc_request {
+	unsigned long channels;
+	bool do_avg;
+	u16 method;
+	u16 type;
+	bool active;
+	bool result_pending;
+	bool raw;
+	int rbuf[TWL4030_MADC_MAX_CHANNELS];
+};
+
+enum conversion_methods {
+	TWL4030_MADC_RT,
+	TWL4030_MADC_SW1,
+	TWL4030_MADC_SW2,
+	TWL4030_MADC_NUM_METHODS
+};
+
+enum sample_type {
+	TWL4030_MADC_WAIT,
+	TWL4030_MADC_IRQ_ONESHOT,
+	TWL4030_MADC_IRQ_REARM
+};
+
 /**
  * struct twl4030_madc_data - a container for madc info
  * @dev:		Pointer to device structure for madc
@@ -72,6 +183,8 @@ struct twl4030_madc_data {
 	u8 isr;
 };
 
+static int twl4030_madc_conversion(struct twl4030_madc_request *req);
+
 static int twl4030_madc_read(struct iio_dev *iio_dev,
 			     const struct iio_chan_spec *chan,
 			     int *val, int *val2, long mask)
@@ -84,7 +197,6 @@ static int twl4030_madc_read(struct iio_dev *iio_dev,
 
 	req.channels = BIT(chan->channel);
 	req.active = false;
-	req.func_cb = NULL;
 	req.type = TWL4030_MADC_WAIT;
 	req.raw = !(mask == IIO_CHAN_INFO_PROCESSED);
 	req.do_avg = (mask == IIO_CHAN_INFO_AVERAGE_RAW);
@@ -341,37 +453,6 @@ static int twl4030_madc_read_channels(struct twl4030_madc_data *madc,
 }
 
 /*
- * Enables irq.
- * @madc - pointer to twl4030_madc_data struct
- * @id - irq number to be enabled
- * can take one of TWL4030_MADC_RT, TWL4030_MADC_SW1, TWL4030_MADC_SW2
- * corresponding to RT, SW1, SW2 conversion requests.
- * If the i2c read fails it returns an error else returns 0.
- */
-static int twl4030_madc_enable_irq(struct twl4030_madc_data *madc, u8 id)
-{
-	u8 val;
-	int ret;
-
-	ret = twl_i2c_read_u8(TWL4030_MODULE_MADC, &val, madc->imr);
-	if (ret) {
-		dev_err(madc->dev, "unable to read imr register 0x%X\n",
-			madc->imr);
-		return ret;
-	}
-
-	val &= ~(1 << id);
-	ret = twl_i2c_write_u8(TWL4030_MODULE_MADC, val, madc->imr);
-	if (ret) {
-		dev_err(madc->dev,
-			"unable to write imr register 0x%X\n", madc->imr);
-		return ret;
-	}
-
-	return 0;
-}
-
-/*
  * Disables irq.
  * @madc - pointer to twl4030_madc_data struct
  * @id - irq number to be disabled
@@ -440,11 +521,6 @@ static irqreturn_t twl4030_madc_threaded_irq_handler(int irq, void *_madc)
 		/* Read results */
 		len = twl4030_madc_read_channels(madc, method->rbase,
 						 r->channels, r->rbuf, r->raw);
-		/* Return results to caller */
-		if (r->func_cb != NULL) {
-			r->func_cb(len, r->channels, r->rbuf);
-			r->func_cb = NULL;
-		}
 		/* Free request */
 		r->result_pending = 0;
 		r->active = 0;
@@ -466,11 +542,6 @@ err_i2c:
 		/* Read results */
 		len = twl4030_madc_read_channels(madc, method->rbase,
 						 r->channels, r->rbuf, r->raw);
-		/* Return results to caller */
-		if (r->func_cb != NULL) {
-			r->func_cb(len, r->channels, r->rbuf);
-			r->func_cb = NULL;
-		}
 		/* Free request */
 		r->result_pending = 0;
 		r->active = 0;
@@ -480,23 +551,6 @@ err_i2c:
 	return IRQ_HANDLED;
 }
 
-static int twl4030_madc_set_irq(struct twl4030_madc_data *madc,
-				struct twl4030_madc_request *req)
-{
-	struct twl4030_madc_request *p;
-	int ret;
-
-	p = &madc->requests[req->method];
-	memcpy(p, req, sizeof(*req));
-	ret = twl4030_madc_enable_irq(madc, req->method);
-	if (ret < 0) {
-		dev_err(madc->dev, "enable irq failed!!\n");
-		return ret;
-	}
-
-	return 0;
-}
-
 /*
  * Function which enables the madc conversion
  * by writing to the control register.
@@ -568,7 +622,7 @@ static int twl4030_madc_wait_conversion_ready(struct twl4030_madc_data *madc,
  * be a negative error value in the corresponding array element.
  * returns 0 if succeeds else error value
  */
-int twl4030_madc_conversion(struct twl4030_madc_request *req)
+static int twl4030_madc_conversion(struct twl4030_madc_request *req)
 {
 	const struct twl4030_madc_conversion_method *method;
 	int ret;
@@ -605,17 +659,6 @@ int twl4030_madc_conversion(struct twl4030_madc_request *req)
 			goto out;
 		}
 	}
-	if (req->type == TWL4030_MADC_IRQ_ONESHOT && req->func_cb != NULL) {
-		ret = twl4030_madc_set_irq(twl4030_madc, req);
-		if (ret < 0)
-			goto out;
-		ret = twl4030_madc_start_conversion(twl4030_madc, req->method);
-		if (ret < 0)
-			goto out;
-		twl4030_madc->requests[req->method].active = 1;
-		ret = 0;
-		goto out;
-	}
 	/* With RT method we should not be here anymore */
 	if (req->method == TWL4030_MADC_RT) {
 		ret = -EINVAL;
@@ -640,28 +683,6 @@ out:
 
 	return ret;
 }
-EXPORT_SYMBOL_GPL(twl4030_madc_conversion);
-
-int twl4030_get_madc_conversion(int channel_no)
-{
-	struct twl4030_madc_request req;
-	int temp = 0;
-	int ret;
-
-	req.channels = (1 << channel_no);
-	req.method = TWL4030_MADC_SW2;
-	req.active = 0;
-	req.raw = 0;
-	req.func_cb = NULL;
-	ret = twl4030_madc_conversion(&req);
-	if (ret < 0)
-		return ret;
-	if (req.rbuf[channel_no] > 0)
-		temp = req.rbuf[channel_no];
-
-	return temp;
-}
-EXPORT_SYMBOL_GPL(twl4030_get_madc_conversion);
 
 /**
  * twl4030_madc_set_current_generator() - setup bias current
diff --git a/drivers/iio/adc/xilinx-xadc-core.c b/drivers/iio/adc/xilinx-xadc-core.c
index 56cf5907a5f0..4a60497a1f19 100644
--- a/drivers/iio/adc/xilinx-xadc-core.c
+++ b/drivers/iio/adc/xilinx-xadc-core.c
@@ -1204,7 +1204,10 @@ static int xadc_probe(struct platform_device *pdev)
 		ret = PTR_ERR(xadc->clk);
 		goto err_free_samplerate_trigger;
 	}
-	clk_prepare_enable(xadc->clk);
+
+	ret = clk_prepare_enable(xadc->clk);
+	if (ret)
+		goto err_free_samplerate_trigger;
 
 	ret = xadc->ops->setup(pdev, indio_dev, irq);
 	if (ret)
diff --git a/drivers/iio/common/hid-sensors/Kconfig b/drivers/iio/common/hid-sensors/Kconfig
index 39188b72cd3b..80105378b0ba 100644
--- a/drivers/iio/common/hid-sensors/Kconfig
+++ b/drivers/iio/common/hid-sensors/Kconfig
@@ -16,7 +16,7 @@ config HID_SENSOR_IIO_COMMON
 
 config HID_SENSOR_IIO_TRIGGER
 	tristate "Common module (trigger) for all HID Sensor IIO drivers"
-	depends on HID_SENSOR_HUB && HID_SENSOR_IIO_COMMON
+	depends on HID_SENSOR_HUB && HID_SENSOR_IIO_COMMON && IIO_BUFFER
 	select IIO_TRIGGER
 	help
 	  Say yes here to build trigger support for HID sensors.
diff --git a/drivers/iio/imu/inv_mpu6050/inv_mpu_core.c b/drivers/iio/imu/inv_mpu6050/inv_mpu_core.c
index 88a7c5d4e4d2..44830bce13df 100644
--- a/drivers/iio/imu/inv_mpu6050/inv_mpu_core.c
+++ b/drivers/iio/imu/inv_mpu6050/inv_mpu_core.c
@@ -188,7 +188,6 @@ int inv_mpu6050_set_power_itg(struct inv_mpu6050_state *st, bool power_on)
 	int result = 0;
 
 	if (power_on) {
-		/* Already under indio-dev->mlock mutex */
 		if (!st->powerup_count)
 			result = regmap_write(st->map, st->reg->pwr_mgmt_1, 0);
 		if (!result)
@@ -329,50 +328,37 @@ inv_mpu6050_read_raw(struct iio_dev *indio_dev,
 		int result;
 
 		ret = IIO_VAL_INT;
-		result = 0;
-		mutex_lock(&indio_dev->mlock);
-		if (!st->chip_config.enable) {
-			result = inv_mpu6050_set_power_itg(st, true);
-			if (result)
-				goto error_read_raw;
-		}
-		/* when enable is on, power is already on */
+		mutex_lock(&st->lock);
+		result = iio_device_claim_direct_mode(indio_dev);
+		if (result)
+			goto error_read_raw_unlock;
+		result = inv_mpu6050_set_power_itg(st, true);
+		if (result)
+			goto error_read_raw_release;
 		switch (chan->type) {
 		case IIO_ANGL_VEL:
-			if (!st->chip_config.gyro_fifo_enable ||
-			    !st->chip_config.enable) {
-				result = inv_mpu6050_switch_engine(st, true,
-						INV_MPU6050_BIT_PWR_GYRO_STBY);
-				if (result)
-					goto error_read_raw;
-			}
+			result = inv_mpu6050_switch_engine(st, true,
+					INV_MPU6050_BIT_PWR_GYRO_STBY);
+			if (result)
+				goto error_read_raw_power_off;
 			ret = inv_mpu6050_sensor_show(st, st->reg->raw_gyro,
 						      chan->channel2, val);
-			if (!st->chip_config.gyro_fifo_enable ||
-			    !st->chip_config.enable) {
-				result = inv_mpu6050_switch_engine(st, false,
-						INV_MPU6050_BIT_PWR_GYRO_STBY);
-				if (result)
-					goto error_read_raw;
-			}
+			result = inv_mpu6050_switch_engine(st, false,
+					INV_MPU6050_BIT_PWR_GYRO_STBY);
+			if (result)
+				goto error_read_raw_power_off;
 			break;
 		case IIO_ACCEL:
-			if (!st->chip_config.accl_fifo_enable ||
-			    !st->chip_config.enable) {
-				result = inv_mpu6050_switch_engine(st, true,
-						INV_MPU6050_BIT_PWR_ACCL_STBY);
-				if (result)
-					goto error_read_raw;
-			}
+			result = inv_mpu6050_switch_engine(st, true,
+					INV_MPU6050_BIT_PWR_ACCL_STBY);
+			if (result)
+				goto error_read_raw_power_off;
 			ret = inv_mpu6050_sensor_show(st, st->reg->raw_accl,
 						      chan->channel2, val);
-			if (!st->chip_config.accl_fifo_enable ||
-			    !st->chip_config.enable) {
-				result = inv_mpu6050_switch_engine(st, false,
-						INV_MPU6050_BIT_PWR_ACCL_STBY);
-				if (result)
-					goto error_read_raw;
-			}
+			result = inv_mpu6050_switch_engine(st, false,
+					INV_MPU6050_BIT_PWR_ACCL_STBY);
+			if (result)
+				goto error_read_raw_power_off;
 			break;
 		case IIO_TEMP:
 			/* wait for stablization */
@@ -384,10 +370,12 @@ inv_mpu6050_read_raw(struct iio_dev *indio_dev,
 			ret = -EINVAL;
 			break;
 		}
-error_read_raw:
-		if (!st->chip_config.enable)
-			result |= inv_mpu6050_set_power_itg(st, false);
-		mutex_unlock(&indio_dev->mlock);
+error_read_raw_power_off:
+		result |= inv_mpu6050_set_power_itg(st, false);
+error_read_raw_release:
+		iio_device_release_direct_mode(indio_dev);
+error_read_raw_unlock:
+		mutex_unlock(&st->lock);
 		if (result)
 			return result;
 
@@ -396,13 +384,17 @@ error_read_raw:
 	case IIO_CHAN_INFO_SCALE:
 		switch (chan->type) {
 		case IIO_ANGL_VEL:
+			mutex_lock(&st->lock);
 			*val  = 0;
 			*val2 = gyro_scale_6050[st->chip_config.fsr];
+			mutex_unlock(&st->lock);
 
 			return IIO_VAL_INT_PLUS_NANO;
 		case IIO_ACCEL:
+			mutex_lock(&st->lock);
 			*val = 0;
 			*val2 = accel_scale[st->chip_config.accl_fs];
+			mutex_unlock(&st->lock);
 
 			return IIO_VAL_INT_PLUS_MICRO;
 		case IIO_TEMP:
@@ -425,12 +417,16 @@ error_read_raw:
 	case IIO_CHAN_INFO_CALIBBIAS:
 		switch (chan->type) {
 		case IIO_ANGL_VEL:
+			mutex_lock(&st->lock);
 			ret = inv_mpu6050_sensor_show(st, st->reg->gyro_offset,
 						chan->channel2, val);
+			mutex_unlock(&st->lock);
 			return IIO_VAL_INT;
 		case IIO_ACCEL:
+			mutex_lock(&st->lock);
 			ret = inv_mpu6050_sensor_show(st, st->reg->accl_offset,
 						chan->channel2, val);
+			mutex_unlock(&st->lock);
 			return IIO_VAL_INT;
 
 		default:
@@ -506,18 +502,17 @@ static int inv_mpu6050_write_raw(struct iio_dev *indio_dev,
 	struct inv_mpu6050_state  *st = iio_priv(indio_dev);
 	int result;
 
-	mutex_lock(&indio_dev->mlock);
+	mutex_lock(&st->lock);
 	/*
 	 * we should only update scale when the chip is disabled, i.e.
 	 * not running
 	 */
-	if (st->chip_config.enable) {
-		result = -EBUSY;
-		goto error_write_raw;
-	}
+	result = iio_device_claim_direct_mode(indio_dev);
+	if (result)
+		goto error_write_raw_unlock;
 	result = inv_mpu6050_set_power_itg(st, true);
 	if (result)
-		goto error_write_raw;
+		goto error_write_raw_release;
 
 	switch (mask) {
 	case IIO_CHAN_INFO_SCALE:
@@ -553,9 +548,11 @@ static int inv_mpu6050_write_raw(struct iio_dev *indio_dev,
 		break;
 	}
 
-error_write_raw:
 	result |= inv_mpu6050_set_power_itg(st, false);
-	mutex_unlock(&indio_dev->mlock);
+error_write_raw_release:
+	iio_device_release_direct_mode(indio_dev);
+error_write_raw_unlock:
+	mutex_unlock(&st->lock);
 
 	return result;
 }
@@ -611,31 +608,35 @@ inv_mpu6050_fifo_rate_store(struct device *dev, struct device_attribute *attr,
 	if (fifo_rate < INV_MPU6050_MIN_FIFO_RATE ||
 	    fifo_rate > INV_MPU6050_MAX_FIFO_RATE)
 		return -EINVAL;
-	if (fifo_rate == st->chip_config.fifo_rate)
-		return count;
 
-	mutex_lock(&indio_dev->mlock);
-	if (st->chip_config.enable) {
-		result = -EBUSY;
-		goto fifo_rate_fail;
+	mutex_lock(&st->lock);
+	if (fifo_rate == st->chip_config.fifo_rate) {
+		result = 0;
+		goto fifo_rate_fail_unlock;
 	}
+	result = iio_device_claim_direct_mode(indio_dev);
+	if (result)
+		goto fifo_rate_fail_unlock;
 	result = inv_mpu6050_set_power_itg(st, true);
 	if (result)
-		goto fifo_rate_fail;
+		goto fifo_rate_fail_release;
 
 	d = INV_MPU6050_ONE_K_HZ / fifo_rate - 1;
 	result = regmap_write(st->map, st->reg->sample_rate_div, d);
 	if (result)
-		goto fifo_rate_fail;
+		goto fifo_rate_fail_power_off;
 	st->chip_config.fifo_rate = fifo_rate;
 
 	result = inv_mpu6050_set_lpf(st, fifo_rate);
 	if (result)
-		goto fifo_rate_fail;
+		goto fifo_rate_fail_power_off;
 
-fifo_rate_fail:
+fifo_rate_fail_power_off:
 	result |= inv_mpu6050_set_power_itg(st, false);
-	mutex_unlock(&indio_dev->mlock);
+fifo_rate_fail_release:
+	iio_device_release_direct_mode(indio_dev);
+fifo_rate_fail_unlock:
+	mutex_unlock(&st->lock);
 	if (result)
 		return result;
 
@@ -650,8 +651,13 @@ inv_fifo_rate_show(struct device *dev, struct device_attribute *attr,
 		   char *buf)
 {
 	struct inv_mpu6050_state *st = iio_priv(dev_to_iio_dev(dev));
+	unsigned fifo_rate;
+
+	mutex_lock(&st->lock);
+	fifo_rate = st->chip_config.fifo_rate;
+	mutex_unlock(&st->lock);
 
-	return sprintf(buf, "%d\n", st->chip_config.fifo_rate);
+	return scnprintf(buf, PAGE_SIZE, "%u\n", fifo_rate);
 }
 
 /**
@@ -678,7 +684,8 @@ static ssize_t inv_attr_show(struct device *dev, struct device_attribute *attr,
 	case ATTR_ACCL_MATRIX:
 		m = st->plat_data.orientation;
 
-		return sprintf(buf, "%d, %d, %d; %d, %d, %d; %d, %d, %d\n",
+		return scnprintf(buf, PAGE_SIZE,
+			"%d, %d, %d; %d, %d, %d; %d, %d, %d\n",
 			m[0], m[1], m[2], m[3], m[4], m[5], m[6], m[7], m[8]);
 	default:
 		return -EINVAL;
@@ -803,27 +810,42 @@ static int inv_check_and_setup_chip(struct inv_mpu6050_state *st)
 {
 	int result;
 	unsigned int regval;
+	int i;
 
 	st->hw  = &hw_info[st->chip_type];
 	st->reg = hw_info[st->chip_type].reg;
 
-	/* reset to make sure previous state are not there */
-	result = regmap_write(st->map, st->reg->pwr_mgmt_1,
-			      INV_MPU6050_BIT_H_RESET);
-	if (result)
-		return result;
-	msleep(INV_MPU6050_POWER_UP_TIME);
-
 	/* check chip self-identification */
 	result = regmap_read(st->map, INV_MPU6050_REG_WHOAMI, &regval);
 	if (result)
 		return result;
 	if (regval != st->hw->whoami) {
-		dev_warn(regmap_get_device(st->map),
-				"whoami mismatch got %#02x expected %#02hhx for %s\n",
+		/* check whoami against all possible values */
+		for (i = 0; i < INV_NUM_PARTS; ++i) {
+			if (regval == hw_info[i].whoami) {
+				dev_warn(regmap_get_device(st->map),
+					"whoami mismatch got %#02x (%s)"
+					"expected %#02hhx (%s)\n",
+					regval, hw_info[i].name,
+					st->hw->whoami, st->hw->name);
+				break;
+			}
+		}
+		if (i >= INV_NUM_PARTS) {
+			dev_err(regmap_get_device(st->map),
+				"invalid whoami %#02x expected %#02hhx (%s)\n",
 				regval, st->hw->whoami, st->hw->name);
+			return -ENODEV;
+		}
 	}
 
+	/* reset to make sure previous state are not there */
+	result = regmap_write(st->map, st->reg->pwr_mgmt_1,
+			      INV_MPU6050_BIT_H_RESET);
+	if (result)
+		return result;
+	msleep(INV_MPU6050_POWER_UP_TIME);
+
 	/*
 	 * toggle power state. After reset, the sleep bit could be on
 	 * or off depending on the OTP settings. Toggling power would
@@ -869,6 +891,7 @@ int inv_mpu_core_probe(struct regmap *regmap, int irq, const char *name,
 		return -ENODEV;
 	}
 	st = iio_priv(indio_dev);
+	mutex_init(&st->lock);
 	st->chip_type = chip_type;
 	st->powerup_count = 0;
 	st->irq = irq;
@@ -962,12 +985,26 @@ EXPORT_SYMBOL_GPL(inv_mpu_core_remove);
 
 static int inv_mpu_resume(struct device *dev)
 {
-	return inv_mpu6050_set_power_itg(iio_priv(dev_get_drvdata(dev)), true);
+	struct inv_mpu6050_state *st = iio_priv(dev_get_drvdata(dev));
+	int result;
+
+	mutex_lock(&st->lock);
+	result = inv_mpu6050_set_power_itg(st, true);
+	mutex_unlock(&st->lock);
+
+	return result;
 }
 
 static int inv_mpu_suspend(struct device *dev)
 {
-	return inv_mpu6050_set_power_itg(iio_priv(dev_get_drvdata(dev)), false);
+	struct inv_mpu6050_state *st = iio_priv(dev_get_drvdata(dev));
+	int result;
+
+	mutex_lock(&st->lock);
+	result = inv_mpu6050_set_power_itg(st, false);
+	mutex_unlock(&st->lock);
+
+	return result;
 }
 #endif /* CONFIG_PM_SLEEP */
 
diff --git a/drivers/iio/imu/inv_mpu6050/inv_mpu_i2c.c b/drivers/iio/imu/inv_mpu6050/inv_mpu_i2c.c
index 64b5f5b92200..fcd7a92b6cf8 100644
--- a/drivers/iio/imu/inv_mpu6050/inv_mpu_i2c.c
+++ b/drivers/iio/imu/inv_mpu6050/inv_mpu_i2c.c
@@ -32,7 +32,7 @@ static int inv_mpu6050_select_bypass(struct i2c_mux_core *muxc, u32 chan_id)
 	int ret = 0;
 
 	/* Use the same mutex which was used everywhere to protect power-op */
-	mutex_lock(&indio_dev->mlock);
+	mutex_lock(&st->lock);
 	if (!st->powerup_count) {
 		ret = regmap_write(st->map, st->reg->pwr_mgmt_1, 0);
 		if (ret)
@@ -48,7 +48,7 @@ static int inv_mpu6050_select_bypass(struct i2c_mux_core *muxc, u32 chan_id)
 				   INV_MPU6050_BIT_BYPASS_EN);
 	}
 write_error:
-	mutex_unlock(&indio_dev->mlock);
+	mutex_unlock(&st->lock);
 
 	return ret;
 }
@@ -58,14 +58,14 @@ static int inv_mpu6050_deselect_bypass(struct i2c_mux_core *muxc, u32 chan_id)
 	struct iio_dev *indio_dev = i2c_mux_priv(muxc);
 	struct inv_mpu6050_state *st = iio_priv(indio_dev);
 
-	mutex_lock(&indio_dev->mlock);
+	mutex_lock(&st->lock);
 	/* It doesn't really mattter, if any of the calls fails */
 	regmap_write(st->map, st->reg->int_pin_cfg, INV_MPU6050_INT_PIN_CFG);
 	st->powerup_count--;
 	if (!st->powerup_count)
 		regmap_write(st->map, st->reg->pwr_mgmt_1,
 			     INV_MPU6050_BIT_SLEEP);
-	mutex_unlock(&indio_dev->mlock);
+	mutex_unlock(&st->lock);
 
 	return 0;
 }
diff --git a/drivers/iio/imu/inv_mpu6050/inv_mpu_iio.h b/drivers/iio/imu/inv_mpu6050/inv_mpu_iio.h
index 953a0c09d568..065794162d65 100644
--- a/drivers/iio/imu/inv_mpu6050/inv_mpu_iio.h
+++ b/drivers/iio/imu/inv_mpu6050/inv_mpu_iio.h
@@ -14,6 +14,7 @@
 #include <linux/i2c-mux.h>
 #include <linux/kfifo.h>
 #include <linux/spinlock.h>
+#include <linux/mutex.h>
 #include <linux/iio/iio.h>
 #include <linux/iio/buffer.h>
 #include <linux/regmap.h>
@@ -82,7 +83,6 @@ enum inv_devices {
  *  @fsr:		Full scale range.
  *  @lpf:		Digital low pass filter frequency.
  *  @accl_fs:		accel full scale range.
- *  @enable:		master enable state.
  *  @accl_fifo_enable:	enable accel data output
  *  @gyro_fifo_enable:	enable gyro data output
  *  @fifo_rate:		FIFO update rate.
@@ -91,7 +91,6 @@ struct inv_mpu6050_chip_config {
 	unsigned int fsr:2;
 	unsigned int lpf:3;
 	unsigned int accl_fs:2;
-	unsigned int enable:1;
 	unsigned int accl_fifo_enable:1;
 	unsigned int gyro_fifo_enable:1;
 	u16 fifo_rate;
@@ -114,6 +113,7 @@ struct inv_mpu6050_hw {
 /*
  *  struct inv_mpu6050_state - Driver state variables.
  *  @TIMESTAMP_FIFO_SIZE: fifo size for timestamp.
+ *  @lock:              Chip access lock.
  *  @trig:              IIO trigger.
  *  @chip_config:	Cached attribute information.
  *  @reg:		Map of important registers.
@@ -128,6 +128,7 @@ struct inv_mpu6050_hw {
  */
 struct inv_mpu6050_state {
 #define TIMESTAMP_FIFO_SIZE 16
+	struct mutex lock;
 	struct iio_trigger  *trig;
 	struct inv_mpu6050_chip_config chip_config;
 	const struct inv_mpu6050_reg_map *reg;
diff --git a/drivers/iio/imu/inv_mpu6050/inv_mpu_ring.c b/drivers/iio/imu/inv_mpu6050/inv_mpu_ring.c
index 3a9f3eac91ab..ff81c6aa009d 100644
--- a/drivers/iio/imu/inv_mpu6050/inv_mpu_ring.c
+++ b/drivers/iio/imu/inv_mpu6050/inv_mpu_ring.c
@@ -128,7 +128,7 @@ irqreturn_t inv_mpu6050_read_fifo(int irq, void *p)
 	u16 fifo_count;
 	s64 timestamp;
 
-	mutex_lock(&indio_dev->mlock);
+	mutex_lock(&st->lock);
 	if (!(st->chip_config.accl_fifo_enable |
 		st->chip_config.gyro_fifo_enable))
 		goto end_session;
@@ -178,7 +178,7 @@ irqreturn_t inv_mpu6050_read_fifo(int irq, void *p)
 	}
 
 end_session:
-	mutex_unlock(&indio_dev->mlock);
+	mutex_unlock(&st->lock);
 	iio_trigger_notify_done(indio_dev->trig);
 
 	return IRQ_HANDLED;
@@ -186,7 +186,7 @@ end_session:
 flush_fifo:
 	/* Flush HW and SW FIFOs. */
 	inv_reset_fifo(indio_dev);
-	mutex_unlock(&indio_dev->mlock);
+	mutex_unlock(&st->lock);
 	iio_trigger_notify_done(indio_dev->trig);
 
 	return IRQ_HANDLED;
diff --git a/drivers/iio/imu/inv_mpu6050/inv_mpu_trigger.c b/drivers/iio/imu/inv_mpu6050/inv_mpu_trigger.c
index e8818d4dd4b8..540070f0a230 100644
--- a/drivers/iio/imu/inv_mpu6050/inv_mpu_trigger.c
+++ b/drivers/iio/imu/inv_mpu6050/inv_mpu_trigger.c
@@ -90,7 +90,6 @@ static int inv_mpu6050_set_enable(struct iio_dev *indio_dev, bool enable)
 		if (result)
 			return result;
 	}
-	st->chip_config.enable = enable;
 
 	return 0;
 }
@@ -103,7 +102,15 @@ static int inv_mpu6050_set_enable(struct iio_dev *indio_dev, bool enable)
 static int inv_mpu_data_rdy_trigger_set_state(struct iio_trigger *trig,
 					      bool state)
 {
-	return inv_mpu6050_set_enable(iio_trigger_get_drvdata(trig), state);
+	struct iio_dev *indio_dev = iio_trigger_get_drvdata(trig);
+	struct inv_mpu6050_state *st = iio_priv(indio_dev);
+	int result;
+
+	mutex_lock(&st->lock);
+	result = inv_mpu6050_set_enable(indio_dev, state);
+	mutex_unlock(&st->lock);
+
+	return result;
 }
 
 static const struct iio_trigger_ops inv_mpu_trigger_ops = {
diff --git a/drivers/iio/imu/st_lsm6dsx/st_lsm6dsx_buffer.c b/drivers/iio/imu/st_lsm6dsx/st_lsm6dsx_buffer.c
index b19a62d8c884..2a72acc6e049 100644
--- a/drivers/iio/imu/st_lsm6dsx/st_lsm6dsx_buffer.c
+++ b/drivers/iio/imu/st_lsm6dsx/st_lsm6dsx_buffer.c
@@ -37,6 +37,8 @@
 #define ST_LSM6DSX_REG_FIFO_THH_ADDR		0x07
 #define ST_LSM6DSX_FIFO_TH_MASK			GENMASK(11, 0)
 #define ST_LSM6DSX_REG_FIFO_DEC_GXL_ADDR	0x08
+#define ST_LSM6DSX_REG_HLACTIVE_ADDR		0x12
+#define ST_LSM6DSX_REG_HLACTIVE_MASK		BIT(5)
 #define ST_LSM6DSX_REG_FIFO_MODE_ADDR		0x0a
 #define ST_LSM6DSX_FIFO_MODE_MASK		GENMASK(2, 0)
 #define ST_LSM6DSX_FIFO_ODR_MASK		GENMASK(6, 3)
@@ -417,6 +419,7 @@ int st_lsm6dsx_fifo_setup(struct st_lsm6dsx_hw *hw)
 {
 	struct iio_buffer *buffer;
 	unsigned long irq_type;
+	bool irq_active_low;
 	int i, err;
 
 	irq_type = irqd_get_trigger_type(irq_get_irq_data(hw->irq));
@@ -424,12 +427,23 @@ int st_lsm6dsx_fifo_setup(struct st_lsm6dsx_hw *hw)
 	switch (irq_type) {
 	case IRQF_TRIGGER_HIGH:
 	case IRQF_TRIGGER_RISING:
+		irq_active_low = false;
+		break;
+	case IRQF_TRIGGER_LOW:
+	case IRQF_TRIGGER_FALLING:
+		irq_active_low = true;
 		break;
 	default:
 		dev_info(hw->dev, "mode %lx unsupported\n", irq_type);
 		return -EINVAL;
 	}
 
+	err = st_lsm6dsx_write_with_mask(hw, ST_LSM6DSX_REG_HLACTIVE_ADDR,
+					 ST_LSM6DSX_REG_HLACTIVE_MASK,
+					 irq_active_low);
+	if (err < 0)
+		return err;
+
 	err = devm_request_threaded_irq(hw->dev, hw->irq,
 					st_lsm6dsx_handler_irq,
 					st_lsm6dsx_handler_thread,
diff --git a/drivers/iio/industrialio-core.c b/drivers/iio/industrialio-core.c
index 4a1de59d153a..17ec4cee51dc 100644
--- a/drivers/iio/industrialio-core.c
+++ b/drivers/iio/industrialio-core.c
@@ -478,21 +478,16 @@ ssize_t iio_enum_write(struct iio_dev *indio_dev,
 	size_t len)
 {
 	const struct iio_enum *e = (const struct iio_enum *)priv;
-	unsigned int i;
 	int ret;
 
 	if (!e->set)
 		return -EINVAL;
 
-	for (i = 0; i < e->num_items; i++) {
-		if (sysfs_streq(buf, e->items[i]))
-			break;
-	}
-
-	if (i == e->num_items)
-		return -EINVAL;
+	ret = __sysfs_match_string(e->items, e->num_items, buf);
+	if (ret < 0)
+		return ret;
 
-	ret = e->set(indio_dev, chan, i);
+	ret = e->set(indio_dev, chan, ret);
 	return ret ? ret : len;
 }
 EXPORT_SYMBOL_GPL(iio_enum_write);
@@ -1428,7 +1423,7 @@ static void iio_device_unregister_sysfs(struct iio_dev *indio_dev)
 static void iio_dev_release(struct device *device)
 {
 	struct iio_dev *indio_dev = dev_to_iio_dev(device);
-	if (indio_dev->modes & (INDIO_BUFFER_TRIGGERED | INDIO_EVENT_TRIGGERED))
+	if (indio_dev->modes & INDIO_ALL_TRIGGERED_MODES)
 		iio_device_unregister_trigger_consumer(indio_dev);
 	iio_device_unregister_eventset(indio_dev);
 	iio_device_unregister_sysfs(indio_dev);
@@ -1710,7 +1705,7 @@ int iio_device_register(struct iio_dev *indio_dev)
 			"Failed to register event set\n");
 		goto error_free_sysfs;
 	}
-	if (indio_dev->modes & (INDIO_BUFFER_TRIGGERED | INDIO_EVENT_TRIGGERED))
+	if (indio_dev->modes & INDIO_ALL_TRIGGERED_MODES)
 		iio_device_register_trigger_consumer(indio_dev);
 
 	if ((indio_dev->modes & INDIO_ALL_BUFFER_MODES) &&
diff --git a/drivers/iio/magnetometer/st_magn_spi.c b/drivers/iio/magnetometer/st_magn_spi.c
index 6325e7dc8e03..f3cb4dc05391 100644
--- a/drivers/iio/magnetometer/st_magn_spi.c
+++ b/drivers/iio/magnetometer/st_magn_spi.c
@@ -48,8 +48,6 @@ static int st_magn_spi_remove(struct spi_device *spi)
 }
 
 static const struct spi_device_id st_magn_id_table[] = {
-	{ LSM303DLHC_MAGN_DEV_NAME },
-	{ LSM303DLM_MAGN_DEV_NAME },
 	{ LIS3MDL_MAGN_DEV_NAME },
 	{ LSM303AGR_MAGN_DEV_NAME },
 	{},
diff --git a/drivers/iio/proximity/sx9500.c b/drivers/iio/proximity/sx9500.c
index 9ea147f1a50d..f42b3a1c75ff 100644
--- a/drivers/iio/proximity/sx9500.c
+++ b/drivers/iio/proximity/sx9500.c
@@ -878,8 +878,7 @@ static void sx9500_gpio_probe(struct i2c_client *client,
 
 	dev = &client->dev;
 
-	data->gpiod_rst = devm_gpiod_get_index(dev, SX9500_GPIO_RESET,
-					       0, GPIOD_OUT_HIGH);
+	data->gpiod_rst = devm_gpiod_get(dev, SX9500_GPIO_RESET, GPIOD_OUT_HIGH);
 	if (IS_ERR(data->gpiod_rst)) {
 		dev_warn(dev, "gpio get reset pin failed\n");
 		data->gpiod_rst = NULL;
diff --git a/drivers/iio/trigger/stm32-timer-trigger.c b/drivers/iio/trigger/stm32-timer-trigger.c
index 0797f2fe584f..d22bc56dd9fc 100644
--- a/drivers/iio/trigger/stm32-timer-trigger.c
+++ b/drivers/iio/trigger/stm32-timer-trigger.c
@@ -417,12 +417,70 @@ static int stm32_counter_write_raw(struct iio_dev *indio_dev,
 	return -EINVAL;
 }
 
+static int stm32_counter_validate_trigger(struct iio_dev *indio_dev,
+					  struct iio_trigger *trig)
+{
+	struct stm32_timer_trigger *priv = iio_priv(indio_dev);
+	const char * const *cur = priv->valids;
+	unsigned int i = 0;
+
+	if (!is_stm32_timer_trigger(trig))
+		return -EINVAL;
+
+	while (cur && *cur) {
+		if (!strncmp(trig->name, *cur, strlen(trig->name))) {
+			regmap_update_bits(priv->regmap,
+					   TIM_SMCR, TIM_SMCR_TS,
+					   i << TIM_SMCR_TS_SHIFT);
+			return 0;
+		}
+		cur++;
+		i++;
+	}
+
+	return -EINVAL;
+}
+
 static const struct iio_info stm32_trigger_info = {
 	.driver_module = THIS_MODULE,
+	.validate_trigger = stm32_counter_validate_trigger,
 	.read_raw = stm32_counter_read_raw,
 	.write_raw = stm32_counter_write_raw
 };
 
+static const char *const stm32_trigger_modes[] = {
+	"trigger",
+};
+
+static int stm32_set_trigger_mode(struct iio_dev *indio_dev,
+				  const struct iio_chan_spec *chan,
+				  unsigned int mode)
+{
+	struct stm32_timer_trigger *priv = iio_priv(indio_dev);
+
+	regmap_update_bits(priv->regmap, TIM_SMCR, TIM_SMCR_SMS, TIM_SMCR_SMS);
+
+	return 0;
+}
+
+static int stm32_get_trigger_mode(struct iio_dev *indio_dev,
+				  const struct iio_chan_spec *chan)
+{
+	struct stm32_timer_trigger *priv = iio_priv(indio_dev);
+	u32 smcr;
+
+	regmap_read(priv->regmap, TIM_SMCR, &smcr);
+
+	return smcr == TIM_SMCR_SMS ? 0 : -EINVAL;
+}
+
+static const struct iio_enum stm32_trigger_mode_enum = {
+	.items = stm32_trigger_modes,
+	.num_items = ARRAY_SIZE(stm32_trigger_modes),
+	.set = stm32_set_trigger_mode,
+	.get = stm32_get_trigger_mode
+};
+
 static const char *const stm32_enable_modes[] = {
 	"always",
 	"gated",
@@ -606,6 +664,8 @@ static const struct iio_chan_spec_ext_info stm32_trigger_count_info[] = {
 	IIO_ENUM_AVAILABLE("quadrature_mode", &stm32_quadrature_mode_enum),
 	IIO_ENUM("enable_mode", IIO_SEPARATE, &stm32_enable_mode_enum),
 	IIO_ENUM_AVAILABLE("enable_mode", &stm32_enable_mode_enum),
+	IIO_ENUM("trigger_mode", IIO_SEPARATE, &stm32_trigger_mode_enum),
+	IIO_ENUM_AVAILABLE("trigger_mode", &stm32_trigger_mode_enum),
 	{}
 };
 
@@ -630,6 +690,7 @@ static struct stm32_timer_trigger *stm32_setup_counter_device(struct device *dev
 	indio_dev->name = dev_name(dev);
 	indio_dev->dev.parent = dev;
 	indio_dev->info = &stm32_trigger_info;
+	indio_dev->modes = INDIO_HARDWARE_TRIGGERED;
 	indio_dev->num_channels = 1;
 	indio_dev->channels = &stm32_trigger_channel;
 	indio_dev->dev.of_node = dev->of_node;