igb: unbreak I2C bit-banging on i350

The driver tried to use Linux' native software I2C bus master
(i2c-algo-bits) for exporting the I2C interface that talks to the SFP
cage(s) towards userspace. As-is, however, the physical SCL/SDA pins
were not moving at all, staying at logical 1 all the time.

The main culprit was the I2CPARAMS register where igb was not setting
the I2CBB_EN bit. That meant that all the careful signal bit-banging was
actually not being propagated to the chip pads (I verified this with a
scope).

The bit-banging was not correct either, because I2C is supposed to be an
open-collector bus, and the code was driving both lines via a totem
pole. The code was also trying to do operations which did not make any
sense with the i2c-algo-bits, namely manipulating both SDA and SCL from
igb_set_i2c_data (which is only supposed to set SDA). I'm not sure if
that was meant as an optimization, or was just flat out wrong, but given
that the i2c-algo-bits is set up to work with a totally dumb GPIO-ish
implementation underneath, there's no need for this code to be smart.

The open-drain vs. totem-pole is fixed by the usual trick where the
logical zero is implemented via regular output mode and outputting a
logical 0, and the logical high is implemented via the IO pad configured
as an input (thus floating), and letting the mandatory pull-up resistors
do the rest. Anything else is actually wrong on I2C where all devices
are supposed to have open-drain connection to the bus.

The missing I2CBB_EN is set (along with a safe initial value of the
GPIOs) just before registering this software I2C bus.

The chip datasheet mentions HW-implemented I2C transactions (SFP EEPROM
reads and writes) as well, but I'm not touching these for simplicity.

Tested on a LR-Link LRES2203PF-2SFP (which is an almost-miniPCIe form
factor card, a cable, and a module with two SFP cages). There was one
casualty, an old broken SFP we had laying around, which was used to
solder some thin wires as a DIY I2C breakout. Thanks for your service.
With this patch in place, I can `i2cdump -y 3 0x51 c` and read back data
which make sense. Yay.

Signed-off-by: Jan Kundrát <jan.kundrat@cesnet.cz>
See-also: https://www.spinics.net/lists/netdev/msg490554.html
Reviewed-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Tony Brelinski <tony.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>

1 files changed, 15 insertions, 8 deletions

diff --git a/drivers/net/ethernet/intel/igb/igb_main.c b/drivers/net/ethernet/intel/igb/igb_main.c
index e67a71c3f141..836be0d3b291 100644
--- a/drivers/net/ethernet/intel/igb/igb_main.c
+++ b/drivers/net/ethernet/intel/igb/igb_main.c
@@ -577,16 +577,15 @@ static void igb_set_i2c_data(void *data, int state)
 	struct e1000_hw *hw = &adapter->hw;
 	s32 i2cctl = rd32(E1000_I2CPARAMS);
 
-	if (state)
-		i2cctl |= E1000_I2C_DATA_OUT;
-	else
+	if (state) {
+		i2cctl |= E1000_I2C_DATA_OUT | E1000_I2C_DATA_OE_N;
+	} else {
+		i2cctl &= ~E1000_I2C_DATA_OE_N;
 		i2cctl &= ~E1000_I2C_DATA_OUT;
+	}
 
-	i2cctl &= ~E1000_I2C_DATA_OE_N;
-	i2cctl |= E1000_I2C_CLK_OE_N;
 	wr32(E1000_I2CPARAMS, i2cctl);
 	wrfl();
-
 }
 
 /**
@@ -603,8 +602,7 @@ static void igb_set_i2c_clk(void *data, int state)
 	s32 i2cctl = rd32(E1000_I2CPARAMS);
 
 	if (state) {
-		i2cctl |= E1000_I2C_CLK_OUT;
-		i2cctl &= ~E1000_I2C_CLK_OE_N;
+		i2cctl |= E1000_I2C_CLK_OUT | E1000_I2C_CLK_OE_N;
 	} else {
 		i2cctl &= ~E1000_I2C_CLK_OUT;
 		i2cctl &= ~E1000_I2C_CLK_OE_N;
@@ -3116,12 +3114,21 @@ static void igb_init_mas(struct igb_adapter *adapter)
  **/
 static s32 igb_init_i2c(struct igb_adapter *adapter)
 {
+	struct e1000_hw *hw = &adapter->hw;
 	s32 status = 0;
+	s32 i2cctl;
 
 	/* I2C interface supported on i350 devices */
 	if (adapter->hw.mac.type != e1000_i350)
 		return 0;
 
+	i2cctl = rd32(E1000_I2CPARAMS);
+	i2cctl |= E1000_I2CBB_EN
+		| E1000_I2C_CLK_OUT | E1000_I2C_CLK_OE_N
+		| E1000_I2C_DATA_OUT | E1000_I2C_DATA_OE_N;
+	wr32(E1000_I2CPARAMS, i2cctl);
+	wrfl();
+
 	/* Initialize the i2c bus which is controlled by the registers.
 	 * This bus will use the i2c_algo_bit structure that implements
 	 * the protocol through toggling of the 4 bits in the register.