Merge branch 'pci/controller/broadcom'

- Add DT property "brcm,clkreq-mode" and driver support for different
  CLKREQ# modes (Jim Quinlan)

* pci/controller/broadcom:
  PCI: brcmstb: Configure HW CLKREQ# mode appropriate for downstream device
  dt-bindings: PCI: brcmstb: Add property "brcm,clkreq-mode"

1 files changed, 86 insertions, 10 deletions

diff --git a/drivers/pci/controller/pcie-brcmstb.c b/drivers/pci/controller/pcie-brcmstb.c
index f9dd6622fe10..5b0730c3891b 100644
--- a/drivers/pci/controller/pcie-brcmstb.c
+++ b/drivers/pci/controller/pcie-brcmstb.c
@@ -48,6 +48,9 @@
 #define PCIE_RC_CFG_PRIV1_LINK_CAPABILITY			0x04dc
 #define  PCIE_RC_CFG_PRIV1_LINK_CAPABILITY_ASPM_SUPPORT_MASK	0xc00
 
+#define PCIE_RC_CFG_PRIV1_ROOT_CAP			0x4f8
+#define  PCIE_RC_CFG_PRIV1_ROOT_CAP_L1SS_MODE_MASK	0xf8
+
 #define PCIE_RC_DL_MDIO_ADDR				0x1100
 #define PCIE_RC_DL_MDIO_WR_DATA				0x1104
 #define PCIE_RC_DL_MDIO_RD_DATA				0x1108
@@ -121,9 +124,12 @@
 
 #define PCIE_MISC_HARD_PCIE_HARD_DEBUG					0x4204
 #define  PCIE_MISC_HARD_PCIE_HARD_DEBUG_CLKREQ_DEBUG_ENABLE_MASK	0x2
+#define  PCIE_MISC_HARD_PCIE_HARD_DEBUG_L1SS_ENABLE_MASK		0x200000
 #define  PCIE_MISC_HARD_PCIE_HARD_DEBUG_SERDES_IDDQ_MASK		0x08000000
 #define  PCIE_BMIPS_MISC_HARD_PCIE_HARD_DEBUG_SERDES_IDDQ_MASK		0x00800000
-
+#define  PCIE_CLKREQ_MASK \
+	  (PCIE_MISC_HARD_PCIE_HARD_DEBUG_CLKREQ_DEBUG_ENABLE_MASK | \
+	   PCIE_MISC_HARD_PCIE_HARD_DEBUG_L1SS_ENABLE_MASK)
 
 #define PCIE_INTR2_CPU_BASE		0x4300
 #define PCIE_MSI_INTR2_BASE		0x4500
@@ -1028,13 +1034,89 @@ static int brcm_pcie_setup(struct brcm_pcie *pcie)
 	return 0;
 }
 
+/*
+ * This extends the timeout period for an access to an internal bus.  This
+ * access timeout may occur during L1SS sleep periods, even without the
+ * presence of a PCIe access.
+ */
+static void brcm_extend_rbus_timeout(struct brcm_pcie *pcie)
+{
+	/* TIMEOUT register is two registers before RGR1_SW_INIT_1 */
+	const unsigned int REG_OFFSET = PCIE_RGR1_SW_INIT_1(pcie) - 8;
+	u32 timeout_us = 4000000; /* 4 seconds, our setting for L1SS */
+
+	/* Each unit in timeout register is 1/216,000,000 seconds */
+	writel(216 * timeout_us, pcie->base + REG_OFFSET);
+}
+
+static void brcm_config_clkreq(struct brcm_pcie *pcie)
+{
+	static const char err_msg[] = "invalid 'brcm,clkreq-mode' DT string\n";
+	const char *mode = "default";
+	u32 clkreq_cntl;
+	int ret, tmp;
+
+	ret = of_property_read_string(pcie->np, "brcm,clkreq-mode", &mode);
+	if (ret && ret != -EINVAL) {
+		dev_err(pcie->dev, err_msg);
+		mode = "safe";
+	}
+
+	/* Start out assuming safe mode (both mode bits cleared) */
+	clkreq_cntl = readl(pcie->base + PCIE_MISC_HARD_PCIE_HARD_DEBUG);
+	clkreq_cntl &= ~PCIE_CLKREQ_MASK;
+
+	if (strcmp(mode, "no-l1ss") == 0) {
+		/*
+		 * "no-l1ss" -- Provides Clock Power Management, L0s, and
+		 * L1, but cannot provide L1 substate (L1SS) power
+		 * savings. If the downstream device connected to the RC is
+		 * L1SS capable AND the OS enables L1SS, all PCIe traffic
+		 * may abruptly halt, potentially hanging the system.
+		 */
+		clkreq_cntl |= PCIE_MISC_HARD_PCIE_HARD_DEBUG_CLKREQ_DEBUG_ENABLE_MASK;
+		/*
+		 * We want to un-advertise L1 substates because if the OS
+		 * tries to configure the controller into using L1 substate
+		 * power savings it may fail or hang when the RC HW is in
+		 * "no-l1ss" mode.
+		 */
+		tmp = readl(pcie->base + PCIE_RC_CFG_PRIV1_ROOT_CAP);
+		u32p_replace_bits(&tmp, 2, PCIE_RC_CFG_PRIV1_ROOT_CAP_L1SS_MODE_MASK);
+		writel(tmp, pcie->base + PCIE_RC_CFG_PRIV1_ROOT_CAP);
+
+	} else if (strcmp(mode, "default") == 0) {
+		/*
+		 * "default" -- Provides L0s, L1, and L1SS, but not
+		 * compliant to provide Clock Power Management;
+		 * specifically, may not be able to meet the Tclron max
+		 * timing of 400ns as specified in "Dynamic Clock Control",
+		 * section 3.2.5.2.2 of the PCIe spec.  This situation is
+		 * atypical and should happen only with older devices.
+		 */
+		clkreq_cntl |= PCIE_MISC_HARD_PCIE_HARD_DEBUG_L1SS_ENABLE_MASK;
+		brcm_extend_rbus_timeout(pcie);
+
+	} else {
+		/*
+		 * "safe" -- No power savings; refclk is driven by RC
+		 * unconditionally.
+		 */
+		if (strcmp(mode, "safe") != 0)
+			dev_err(pcie->dev, err_msg);
+		mode = "safe";
+	}
+	writel(clkreq_cntl, pcie->base + PCIE_MISC_HARD_PCIE_HARD_DEBUG);
+
+	dev_info(pcie->dev, "clkreq-mode set to %s\n", mode);
+}
+
 static int brcm_pcie_start_link(struct brcm_pcie *pcie)
 {
 	struct device *dev = pcie->dev;
 	void __iomem *base = pcie->base;
 	u16 nlw, cls, lnksta;
 	bool ssc_good = false;
-	u32 tmp;
 	int ret, i;
 
 	/* Unassert the fundamental reset */
@@ -1059,6 +1141,8 @@ static int brcm_pcie_start_link(struct brcm_pcie *pcie)
 		return -ENODEV;
 	}
 
+	brcm_config_clkreq(pcie);
+
 	if (pcie->gen)
 		brcm_pcie_set_gen(pcie, pcie->gen);
 
@@ -1077,14 +1161,6 @@ static int brcm_pcie_start_link(struct brcm_pcie *pcie)
 		 pci_speed_string(pcie_link_speed[cls]), nlw,
 		 ssc_good ? "(SSC)" : "(!SSC)");
 
-	/*
-	 * Refclk from RC should be gated with CLKREQ# input when ASPM L0s,L1
-	 * is enabled => setting the CLKREQ_DEBUG_ENABLE field to 1.
-	 */
-	tmp = readl(base + PCIE_MISC_HARD_PCIE_HARD_DEBUG);
-	tmp |= PCIE_MISC_HARD_PCIE_HARD_DEBUG_CLKREQ_DEBUG_ENABLE_MASK;
-	writel(tmp, base + PCIE_MISC_HARD_PCIE_HARD_DEBUG);
-
 	return 0;
 }