Merge tag 'usb-5.14-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb

Pull USB fixes from Greg KH:
 "Here are some USB fixes for 5.14-rc3 to resolve a bunch of tiny
  problems reported. Included in here are:

   - dtsi revert to resolve a problem which broke android systems that
     relied on the dts name to find the USB controller device.

     People are still working out the "real" solution for this, but for
     now the revert is needed.

   - core USB fix for pipe calculation found by syzbot

   - typec fixes

   - gadget driver fixes

   - new usb-serial device ids

   - new USB quirks

   - xhci fixes

   - usb hub fixes for power management issues reported

   - other tiny fixes

  All have been in linux-next with no reported problems"

* tag 'usb-5.14-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (27 commits)
  USB: serial: cp210x: add ID for CEL EM3588 USB ZigBee stick
  Revert "USB: quirks: ignore remote wake-up on Fibocom L850-GL LTE modem"
  usb: cdc-wdm: fix build error when CONFIG_WWAN_CORE is not set
  Revert "arm64: dts: qcom: Harmonize DWC USB3 DT nodes name"
  usb: dwc2: gadget: Fix sending zero length packet in DDMA mode.
  usb: dwc2: Skip clock gating on Samsung SoCs
  usb: renesas_usbhs: Fix superfluous irqs happen after usb_pkt_pop()
  usb: dwc2: gadget: Fix GOUTNAK flow for Slave mode.
  usb: phy: Fix page fault from usb_phy_uevent
  usb: xhci: avoid renesas_usb_fw.mem when it's unusable
  usb: gadget: u_serial: remove WARN_ON on null port
  usb: dwc3: avoid NULL access of usb_gadget_driver
  usb: max-3421: Prevent corruption of freed memory
  usb: gadget: Fix Unbalanced pm_runtime_enable in tegra_xudc_probe
  MAINTAINERS: repair reference in USB IP DRIVER FOR HISILICON KIRIN 970
  usb: typec: stusb160x: Don't block probing of consumer of "connector" nodes
  usb: typec: stusb160x: register role switch before interrupt registration
  USB: usb-storage: Add LaCie Rugged USB3-FW to IGNORE_UAS
  usb: ehci: Prevent missed ehci interrupts with edge-triggered MSI
  usb: hub: Disable USB 3 device initiated lpm if exit latency is too high
  ...

5 files changed, 45 insertions, 43 deletions

diff --git a/drivers/usb/host/ehci-hcd.c b/drivers/usb/host/ehci-hcd.c
index 36f5bf6a0752..10b0365f3439 100644
--- a/drivers/usb/host/ehci-hcd.c
+++ b/drivers/usb/host/ehci-hcd.c
@@ -703,24 +703,28 @@ EXPORT_SYMBOL_GPL(ehci_setup);
 static irqreturn_t ehci_irq (struct usb_hcd *hcd)
 {
 	struct ehci_hcd		*ehci = hcd_to_ehci (hcd);
-	u32			status, masked_status, pcd_status = 0, cmd;
+	u32			status, current_status, masked_status, pcd_status = 0;
+	u32			cmd;
 	int			bh;
 
 	spin_lock(&ehci->lock);
 
-	status = ehci_readl(ehci, &ehci->regs->status);
+	status = 0;
+	current_status = ehci_readl(ehci, &ehci->regs->status);
+restart:
 
 	/* e.g. cardbus physical eject */
-	if (status == ~(u32) 0) {
+	if (current_status == ~(u32) 0) {
 		ehci_dbg (ehci, "device removed\n");
 		goto dead;
 	}
+	status |= current_status;
 
 	/*
 	 * We don't use STS_FLR, but some controllers don't like it to
 	 * remain on, so mask it out along with the other status bits.
 	 */
-	masked_status = status & (INTR_MASK | STS_FLR);
+	masked_status = current_status & (INTR_MASK | STS_FLR);
 
 	/* Shared IRQ? */
 	if (!masked_status || unlikely(ehci->rh_state == EHCI_RH_HALTED)) {
@@ -730,6 +734,12 @@ static irqreturn_t ehci_irq (struct usb_hcd *hcd)
 
 	/* clear (just) interrupts */
 	ehci_writel(ehci, masked_status, &ehci->regs->status);
+
+	/* For edge interrupts, don't race with an interrupt bit being raised */
+	current_status = ehci_readl(ehci, &ehci->regs->status);
+	if (current_status & INTR_MASK)
+		goto restart;
+
 	cmd = ehci_readl(ehci, &ehci->regs->command);
 	bh = 0;
 
diff --git a/drivers/usb/host/max3421-hcd.c b/drivers/usb/host/max3421-hcd.c
index e7a8e0609853..59cc1bc7f12f 100644
--- a/drivers/usb/host/max3421-hcd.c
+++ b/drivers/usb/host/max3421-hcd.c
@@ -153,8 +153,6 @@ struct max3421_hcd {
 	 */
 	struct urb *curr_urb;
 	enum scheduling_pass sched_pass;
-	struct usb_device *loaded_dev;	/* dev that's loaded into the chip */
-	int loaded_epnum;		/* epnum whose toggles are loaded */
 	int urb_done;			/* > 0 -> no errors, < 0: errno */
 	size_t curr_len;
 	u8 hien;
@@ -492,39 +490,17 @@ max3421_set_speed(struct usb_hcd *hcd, struct usb_device *dev)
  * Caller must NOT hold HCD spinlock.
  */
 static void
-max3421_set_address(struct usb_hcd *hcd, struct usb_device *dev, int epnum,
-		    int force_toggles)
+max3421_set_address(struct usb_hcd *hcd, struct usb_device *dev, int epnum)
 {
-	struct max3421_hcd *max3421_hcd = hcd_to_max3421(hcd);
-	int old_epnum, same_ep, rcvtog, sndtog;
-	struct usb_device *old_dev;
+	int rcvtog, sndtog;
 	u8 hctl;
 
-	old_dev = max3421_hcd->loaded_dev;
-	old_epnum = max3421_hcd->loaded_epnum;
-
-	same_ep = (dev == old_dev && epnum == old_epnum);
-	if (same_ep && !force_toggles)
-		return;
-
-	if (old_dev && !same_ep) {
-		/* save the old end-points toggles: */
-		u8 hrsl = spi_rd8(hcd, MAX3421_REG_HRSL);
-
-		rcvtog = (hrsl >> MAX3421_HRSL_RCVTOGRD_BIT) & 1;
-		sndtog = (hrsl >> MAX3421_HRSL_SNDTOGRD_BIT) & 1;
-
-		/* no locking: HCD (i.e., we) own toggles, don't we? */
-		usb_settoggle(old_dev, old_epnum, 0, rcvtog);
-		usb_settoggle(old_dev, old_epnum, 1, sndtog);
-	}
 	/* setup new endpoint's toggle bits: */
 	rcvtog = usb_gettoggle(dev, epnum, 0);
 	sndtog = usb_gettoggle(dev, epnum, 1);
 	hctl = (BIT(rcvtog + MAX3421_HCTL_RCVTOG0_BIT) |
 		BIT(sndtog + MAX3421_HCTL_SNDTOG0_BIT));
 
-	max3421_hcd->loaded_epnum = epnum;
 	spi_wr8(hcd, MAX3421_REG_HCTL, hctl);
 
 	/*
@@ -532,7 +508,6 @@ max3421_set_address(struct usb_hcd *hcd, struct usb_device *dev, int epnum,
 	 * address-assignment so it's best to just always load the
 	 * address whenever the end-point changed/was forced.
 	 */
-	max3421_hcd->loaded_dev = dev;
 	spi_wr8(hcd, MAX3421_REG_PERADDR, dev->devnum);
 }
 
@@ -667,7 +642,7 @@ max3421_select_and_start_urb(struct usb_hcd *hcd)
 	struct max3421_hcd *max3421_hcd = hcd_to_max3421(hcd);
 	struct urb *urb, *curr_urb = NULL;
 	struct max3421_ep *max3421_ep;
-	int epnum, force_toggles = 0;
+	int epnum;
 	struct usb_host_endpoint *ep;
 	struct list_head *pos;
 	unsigned long flags;
@@ -777,7 +752,6 @@ done:
 			usb_settoggle(urb->dev, epnum, 0, 1);
 			usb_settoggle(urb->dev, epnum, 1, 1);
 			max3421_ep->pkt_state = PKT_STATE_SETUP;
-			force_toggles = 1;
 		} else
 			max3421_ep->pkt_state = PKT_STATE_TRANSFER;
 	}
@@ -785,7 +759,7 @@ done:
 	spin_unlock_irqrestore(&max3421_hcd->lock, flags);
 
 	max3421_ep->last_active = max3421_hcd->frame_number;
-	max3421_set_address(hcd, urb->dev, epnum, force_toggles);
+	max3421_set_address(hcd, urb->dev, epnum);
 	max3421_set_speed(hcd, urb->dev);
 	max3421_next_transfer(hcd, 0);
 	return 1;
@@ -1379,6 +1353,16 @@ max3421_urb_done(struct usb_hcd *hcd)
 		status = 0;
 	urb = max3421_hcd->curr_urb;
 	if (urb) {
+		/* save the old end-points toggles: */
+		u8 hrsl = spi_rd8(hcd, MAX3421_REG_HRSL);
+		int rcvtog = (hrsl >> MAX3421_HRSL_RCVTOGRD_BIT) & 1;
+		int sndtog = (hrsl >> MAX3421_HRSL_SNDTOGRD_BIT) & 1;
+		int epnum = usb_endpoint_num(&urb->ep->desc);
+
+		/* no locking: HCD (i.e., we) own toggles, don't we? */
+		usb_settoggle(urb->dev, epnum, 0, rcvtog);
+		usb_settoggle(urb->dev, epnum, 1, sndtog);
+
 		max3421_hcd->curr_urb = NULL;
 		spin_lock_irqsave(&max3421_hcd->lock, flags);
 		usb_hcd_unlink_urb_from_ep(hcd, urb);
diff --git a/drivers/usb/host/xhci-hub.c b/drivers/usb/host/xhci-hub.c
index e9b18fc17617..151e93c4bd57 100644
--- a/drivers/usb/host/xhci-hub.c
+++ b/drivers/usb/host/xhci-hub.c
@@ -1638,11 +1638,12 @@ int xhci_hub_status_data(struct usb_hcd *hcd, char *buf)
 	 * Inform the usbcore about resume-in-progress by returning
 	 * a non-zero value even if there are no status changes.
 	 */
+	spin_lock_irqsave(&xhci->lock, flags);
+
 	status = bus_state->resuming_ports;
 
 	mask = PORT_CSC | PORT_PEC | PORT_OCC | PORT_PLC | PORT_WRC | PORT_CEC;
 
-	spin_lock_irqsave(&xhci->lock, flags);
 	/* For each port, did anything change?  If so, set that bit in buf. */
 	for (i = 0; i < max_ports; i++) {
 		temp = readl(ports[i]->addr);
diff --git a/drivers/usb/host/xhci-pci-renesas.c b/drivers/usb/host/xhci-pci-renesas.c
index 1da647961c25..5923844ed821 100644
--- a/drivers/usb/host/xhci-pci-renesas.c
+++ b/drivers/usb/host/xhci-pci-renesas.c
@@ -207,8 +207,7 @@ static int renesas_check_rom_state(struct pci_dev *pdev)
 			return 0;
 
 		case RENESAS_ROM_STATUS_NO_RESULT: /* No result yet */
-			dev_dbg(&pdev->dev, "Unknown ROM status ...\n");
-			break;
+			return 0;
 
 		case RENESAS_ROM_STATUS_ERROR: /* Error State */
 		default: /* All other states are marked as "Reserved states" */
@@ -225,12 +224,13 @@ static int renesas_fw_check_running(struct pci_dev *pdev)
 	u8 fw_state;
 	int err;
 
-	/*
-	 * Only if device has ROM and loaded FW we can skip loading and
-	 * return success. Otherwise (even unknown state), attempt to load FW.
-	 */
-	if (renesas_check_rom(pdev) && !renesas_check_rom_state(pdev))
-		return 0;
+	/* Check if device has ROM and loaded, if so skip everything */
+	err = renesas_check_rom(pdev);
+	if (err) { /* we have rom */
+		err = renesas_check_rom_state(pdev);
+		if (!err)
+			return err;
+	}
 
 	/*
 	 * Test if the device is actually needing the firmware. As most
diff --git a/drivers/usb/host/xhci-pci.c b/drivers/usb/host/xhci-pci.c
index 18c2bbddf080..1c9a7957c45c 100644
--- a/drivers/usb/host/xhci-pci.c
+++ b/drivers/usb/host/xhci-pci.c
@@ -636,7 +636,14 @@ static const struct pci_device_id pci_ids[] = {
 	{ /* end: all zeroes */ }
 };
 MODULE_DEVICE_TABLE(pci, pci_ids);
+
+/*
+ * Without CONFIG_USB_XHCI_PCI_RENESAS renesas_xhci_check_request_fw() won't
+ * load firmware, so don't encumber the xhci-pci driver with it.
+ */
+#if IS_ENABLED(CONFIG_USB_XHCI_PCI_RENESAS)
 MODULE_FIRMWARE("renesas_usb_fw.mem");
+#endif
 
 /* pci driver glue; this is a "new style" PCI driver module */
 static struct pci_driver xhci_pci_driver = {