diff options
42 files changed, 3646 insertions, 435 deletions
diff --git a/Documentation/ABI/testing/sysfs-bus-iio-cros-ec b/Documentation/ABI/testing/sysfs-bus-iio-cros-ec new file mode 100644 index 000000000000..297b9720f024 --- /dev/null +++ b/Documentation/ABI/testing/sysfs-bus-iio-cros-ec @@ -0,0 +1,18 @@ +What: /sys/bus/iio/devices/iio:deviceX/calibrate +Date: July 2015 +KernelVersion: 4.7 +Contact: linux-iio@vger.kernel.org +Description: + Writing '1' will perform a FOC (Fast Online Calibration). The + corresponding calibration offsets can be read from *_calibbias + entries. + +What: /sys/bus/iio/devices/iio:deviceX/location +Date: July 2015 +KernelVersion: 4.7 +Contact: linux-iio@vger.kernel.org +Description: + This attribute returns a string with the physical location where + the motion sensor is placed. For example, in a laptop a motion + sensor can be located on the base or on the lid. Current valid + values are 'base' and 'lid'. diff --git a/Documentation/devicetree/bindings/i2c/trivial-devices.txt b/Documentation/devicetree/bindings/i2c/trivial-devices.txt index 6e4ba816094b..03349ad5abfa 100644 --- a/Documentation/devicetree/bindings/i2c/trivial-devices.txt +++ b/Documentation/devicetree/bindings/i2c/trivial-devices.txt @@ -152,6 +152,7 @@ ricoh,rv5c387a I2C bus SERIAL INTERFACE REAL-TIME CLOCK IC samsung,24ad0xd1 S524AD0XF1 (128K/256K-bit Serial EEPROM for Low Power) sgx,vz89x SGX Sensortech VZ89X Sensors sii,s35390a 2-wire CMOS real-time clock +silabs,si7020 Relative Humidity and Temperature Sensors skyworks,sky81452 Skyworks SKY81452: Six-Channel White LED Driver with Touch Panel Bias Supply st,24c256 i2c serial eeprom (24cxx) st,m41t00 Serial real-time clock (RTC) diff --git a/Documentation/devicetree/bindings/iio/gyroscope/invensense,mpu3050.txt b/Documentation/devicetree/bindings/iio/gyroscope/invensense,mpu3050.txt new file mode 100644 index 000000000000..b0d3b59966bc --- /dev/null +++ b/Documentation/devicetree/bindings/iio/gyroscope/invensense,mpu3050.txt @@ -0,0 +1,46 @@ +Invensense MPU-3050 Gyroscope device tree bindings + +Required properties: + - compatible : should be "invensense,mpu3050" + - reg : the I2C address of the sensor + +Optional properties: + - interrupt-parent : should be the phandle for the interrupt controller + - interrupts : interrupt mapping for the trigger interrupt from the + internal oscillator. The following IRQ modes are supported: + IRQ_TYPE_EDGE_RISING, IRQ_TYPE_EDGE_FALLING, IRQ_TYPE_LEVEL_HIGH and + IRQ_TYPE_LEVEL_LOW. The driver should detect and configure the hardware + for the desired interrupt type. + - vdd-supply : supply regulator for the main power voltage. + - vlogic-supply : supply regulator for the signal voltage. + - mount-matrix : see iio/mount-matrix.txt + +Optional subnodes: + - The MPU-3050 will pass through and forward the I2C signals from the + incoming I2C bus, alternatively drive traffic to a slave device (usually + an accelerometer) on its own initiative. Therefore is supports a subnode + i2c gate node. For details see: i2c/i2c-gate.txt + +Example: + +mpu3050@68 { + compatible = "invensense,mpu3050"; + reg = <0x68>; + interrupt-parent = <&foo>; + interrupts = <12 IRQ_TYPE_EDGE_FALLING>; + vdd-supply = <&bar>; + vlogic-supply = <&baz>; + + /* External I2C interface */ + i2c-gate { + #address-cells = <1>; + #size-cells = <0>; + + fnord@18 { + compatible = "fnord"; + reg = <0x18>; + interrupt-parent = <&foo>; + interrupts = <13 IRQ_TYPE_EDGE_FALLING>; + }; + }; +}; diff --git a/Documentation/devicetree/bindings/iio/light/tsl2583.txt b/Documentation/devicetree/bindings/iio/light/tsl2583.txt new file mode 100644 index 000000000000..8e2066c83f70 --- /dev/null +++ b/Documentation/devicetree/bindings/iio/light/tsl2583.txt @@ -0,0 +1,26 @@ +* TAOS TSL 2580/2581/2583 ALS sensor + +Required properties: + + - compatible: Should be one of + "amstaos,tsl2580" + "amstaos,tsl2581" + "amstaos,tsl2583" + - reg: the I2C address of the device + +Optional properties: + + - interrupt-parent: should be the phandle for the interrupt controller + - interrupts: the sole interrupt generated by the device + + Refer to interrupt-controller/interrupts.txt for generic interrupt client + node bindings. + + - vcc-supply: phandle to the regulator that provides power to the sensor. + +Example: + +tsl2581@29 { + compatible = "amstaos,tsl2581"; + reg = <0x29>; +}; diff --git a/Documentation/devicetree/bindings/iio/st-sensors.txt b/Documentation/devicetree/bindings/iio/st-sensors.txt index e41fe340162b..c040c9ad1889 100644 --- a/Documentation/devicetree/bindings/iio/st-sensors.txt +++ b/Documentation/devicetree/bindings/iio/st-sensors.txt @@ -42,6 +42,7 @@ Accelerometers: - st,lsm303agr-accel - st,lis2dh12-accel - st,h3lis331dl-accel +- st,lng2dm-accel Gyroscopes: - st,l3g4200d-gyro diff --git a/MAINTAINERS b/MAINTAINERS index eced366e69b0..ec1ee3ef112e 100644 --- a/MAINTAINERS +++ b/MAINTAINERS @@ -6498,6 +6498,13 @@ S: Maintained F: arch/x86/include/asm/pmc_core.h F: drivers/platform/x86/intel_pmc_core* +INVENSENSE MPU-3050 GYROSCOPE DRIVER +M: Linus Walleij <linus.walleij@linaro.org> +L: linux-iio@vger.kernel.org +S: Maintained +F: drivers/iio/gyro/mpu3050* +F: Documentation/devicetree/bindings/iio/gyroscope/inv,mpu3050.txt + IOC3 ETHERNET DRIVER M: Ralf Baechle <ralf@linux-mips.org> L: linux-mips@linux-mips.org diff --git a/drivers/iio/accel/Kconfig b/drivers/iio/accel/Kconfig index c6cc2c0909a1..c68bdb649005 100644 --- a/drivers/iio/accel/Kconfig +++ b/drivers/iio/accel/Kconfig @@ -127,7 +127,8 @@ config IIO_ST_ACCEL_3AXIS help Say yes here to build support for STMicroelectronics accelerometers: LSM303DLH, LSM303DLHC, LIS3DH, LSM330D, LSM330DL, LSM330DLC, - LIS331DLH, LSM303DL, LSM303DLM, LSM330, LIS2DH12, H3LIS331DL. + LIS331DLH, LSM303DL, LSM303DLM, LSM330, LIS2DH12, H3LIS331DL, + LNG2DM This driver can also be built as a module. If so, these modules will be created: diff --git a/drivers/iio/accel/st_accel.h b/drivers/iio/accel/st_accel.h index f8dfdb690563..7c231687109a 100644 --- a/drivers/iio/accel/st_accel.h +++ b/drivers/iio/accel/st_accel.h @@ -30,6 +30,7 @@ #define LSM303AGR_ACCEL_DEV_NAME "lsm303agr_accel" #define LIS2DH12_ACCEL_DEV_NAME "lis2dh12_accel" #define LIS3L02DQ_ACCEL_DEV_NAME "lis3l02dq" +#define LNG2DM_ACCEL_DEV_NAME "lng2dm" /** * struct st_sensors_platform_data - default accel platform data diff --git a/drivers/iio/accel/st_accel_core.c b/drivers/iio/accel/st_accel_core.c index da3fb069ec5c..b242457d0c80 100644 --- a/drivers/iio/accel/st_accel_core.c +++ b/drivers/iio/accel/st_accel_core.c @@ -231,6 +231,12 @@ #define ST_ACCEL_7_DRDY_IRQ_INT1_MASK 0x04 #define ST_ACCEL_7_MULTIREAD_BIT false +/* CUSTOM VALUES FOR SENSOR 8 */ +#define ST_ACCEL_8_FS_AVL_2_GAIN IIO_G_TO_M_S_2(15600) +#define ST_ACCEL_8_FS_AVL_4_GAIN IIO_G_TO_M_S_2(31200) +#define ST_ACCEL_8_FS_AVL_8_GAIN IIO_G_TO_M_S_2(62500) +#define ST_ACCEL_8_FS_AVL_16_GAIN IIO_G_TO_M_S_2(187500) + static const struct iio_chan_spec st_accel_8bit_channels[] = { ST_SENSORS_LSM_CHANNELS(IIO_ACCEL, BIT(IIO_CHAN_INFO_RAW) | BIT(IIO_CHAN_INFO_SCALE), @@ -726,6 +732,73 @@ static const struct st_sensor_settings st_accel_sensors_settings[] = { .multi_read_bit = ST_ACCEL_7_MULTIREAD_BIT, .bootime = 2, }, + { + .wai = ST_ACCEL_1_WAI_EXP, + .wai_addr = ST_SENSORS_DEFAULT_WAI_ADDRESS, + .sensors_supported = { + [0] = LNG2DM_ACCEL_DEV_NAME, + }, + .ch = (struct iio_chan_spec *)st_accel_8bit_channels, + .odr = { + .addr = ST_ACCEL_1_ODR_ADDR, + .mask = ST_ACCEL_1_ODR_MASK, + .odr_avl = { + { 1, ST_ACCEL_1_ODR_AVL_1HZ_VAL, }, + { 10, ST_ACCEL_1_ODR_AVL_10HZ_VAL, }, + { 25, ST_ACCEL_1_ODR_AVL_25HZ_VAL, }, + { 50, ST_ACCEL_1_ODR_AVL_50HZ_VAL, }, + { 100, ST_ACCEL_1_ODR_AVL_100HZ_VAL, }, + { 200, ST_ACCEL_1_ODR_AVL_200HZ_VAL, }, + { 400, ST_ACCEL_1_ODR_AVL_400HZ_VAL, }, + { 1600, ST_ACCEL_1_ODR_AVL_1600HZ_VAL, }, + }, + }, + .pw = { + .addr = ST_ACCEL_1_ODR_ADDR, + .mask = ST_ACCEL_1_ODR_MASK, + .value_off = ST_SENSORS_DEFAULT_POWER_OFF_VALUE, + }, + .enable_axis = { + .addr = ST_SENSORS_DEFAULT_AXIS_ADDR, + .mask = ST_SENSORS_DEFAULT_AXIS_MASK, + }, + .fs = { + .addr = ST_ACCEL_1_FS_ADDR, + .mask = ST_ACCEL_1_FS_MASK, + .fs_avl = { + [0] = { + .num = ST_ACCEL_FS_AVL_2G, + .value = ST_ACCEL_1_FS_AVL_2_VAL, + .gain = ST_ACCEL_8_FS_AVL_2_GAIN, + }, + [1] = { + .num = ST_ACCEL_FS_AVL_4G, + .value = ST_ACCEL_1_FS_AVL_4_VAL, + .gain = ST_ACCEL_8_FS_AVL_4_GAIN, + }, + [2] = { + .num = ST_ACCEL_FS_AVL_8G, + .value = ST_ACCEL_1_FS_AVL_8_VAL, + .gain = ST_ACCEL_8_FS_AVL_8_GAIN, + }, + [3] = { + .num = ST_ACCEL_FS_AVL_16G, + .value = ST_ACCEL_1_FS_AVL_16_VAL, + .gain = ST_ACCEL_8_FS_AVL_16_GAIN, + }, + }, + }, + .drdy_irq = { + .addr = ST_ACCEL_1_DRDY_IRQ_ADDR, + .mask_int1 = ST_ACCEL_1_DRDY_IRQ_INT1_MASK, + .mask_int2 = ST_ACCEL_1_DRDY_IRQ_INT2_MASK, + .addr_ihl = ST_ACCEL_1_IHL_IRQ_ADDR, + .mask_ihl = ST_ACCEL_1_IHL_IRQ_MASK, + .addr_stat_drdy = ST_SENSORS_DEFAULT_STAT_ADDR, + }, + .multi_read_bit = ST_ACCEL_1_MULTIREAD_BIT, + .bootime = 2, + }, }; static int st_accel_read_raw(struct iio_dev *indio_dev, diff --git a/drivers/iio/accel/st_accel_i2c.c b/drivers/iio/accel/st_accel_i2c.c index e9d427a5df7c..c0f8867aa1ea 100644 --- a/drivers/iio/accel/st_accel_i2c.c +++ b/drivers/iio/accel/st_accel_i2c.c @@ -84,6 +84,10 @@ static const struct of_device_id st_accel_of_match[] = { .compatible = "st,lis3l02dq", .data = LIS3L02DQ_ACCEL_DEV_NAME, }, + { + .compatible = "st,lng2dm-accel", + .data = LNG2DM_ACCEL_DEV_NAME, + }, {}, }; MODULE_DEVICE_TABLE(of, st_accel_of_match); @@ -135,6 +139,7 @@ static const struct i2c_device_id st_accel_id_table[] = { { LSM303AGR_ACCEL_DEV_NAME }, { LIS2DH12_ACCEL_DEV_NAME }, { LIS3L02DQ_ACCEL_DEV_NAME }, + { LNG2DM_ACCEL_DEV_NAME }, {}, }; MODULE_DEVICE_TABLE(i2c, st_accel_id_table); diff --git a/drivers/iio/accel/st_accel_spi.c b/drivers/iio/accel/st_accel_spi.c index efd43941d45d..c25ac50d4600 100644 --- a/drivers/iio/accel/st_accel_spi.c +++ b/drivers/iio/accel/st_accel_spi.c @@ -60,6 +60,7 @@ static const struct spi_device_id st_accel_id_table[] = { { LSM303AGR_ACCEL_DEV_NAME }, { LIS2DH12_ACCEL_DEV_NAME }, { LIS3L02DQ_ACCEL_DEV_NAME }, + { LNG2DM_ACCEL_DEV_NAME }, {}, }; MODULE_DEVICE_TABLE(spi, st_accel_id_table); diff --git a/drivers/iio/adc/at91_adc.c b/drivers/iio/adc/at91_adc.c index bbdac07f4aaa..34b928cefeed 100644 --- a/drivers/iio/adc/at91_adc.c +++ b/drivers/iio/adc/at91_adc.c @@ -30,6 +30,7 @@ #include <linux/iio/trigger.h> #include <linux/iio/trigger_consumer.h> #include <linux/iio/triggered_buffer.h> +#include <linux/pinctrl/consumer.h> /* Registers */ #define AT91_ADC_CR 0x00 /* Control Register */ @@ -1347,6 +1348,32 @@ static int at91_adc_remove(struct platform_device *pdev) return 0; } +#ifdef CONFIG_PM_SLEEP +static int at91_adc_suspend(struct device *dev) +{ + struct iio_dev *idev = platform_get_drvdata(to_platform_device(dev)); + struct at91_adc_state *st = iio_priv(idev); + + pinctrl_pm_select_sleep_state(dev); + clk_disable_unprepare(st->clk); + + return 0; +} + +static int at91_adc_resume(struct device *dev) +{ + struct iio_dev *idev = platform_get_drvdata(to_platform_device(dev)); + struct at91_adc_state *st = iio_priv(idev); + + clk_prepare_enable(st->clk); + pinctrl_pm_select_default_state(dev); + + return 0; +} +#endif + +static SIMPLE_DEV_PM_OPS(at91_adc_pm_ops, at91_adc_suspend, at91_adc_resume); + static struct at91_adc_caps at91sam9260_caps = { .calc_startup_ticks = calc_startup_ticks_9260, .num_channels = 4, @@ -1441,6 +1468,7 @@ static struct platform_driver at91_adc_driver = { .driver = { .name = DRIVER_NAME, .of_match_table = of_match_ptr(at91_adc_dt_ids), + .pm = &at91_adc_pm_ops, }, }; diff --git a/drivers/iio/adc/ti_am335x_adc.c b/drivers/iio/adc/ti_am335x_adc.c index c3cfacca2541..ad9dec30bb30 100644 --- a/drivers/iio/adc/ti_am335x_adc.c +++ b/drivers/iio/adc/ti_am335x_adc.c @@ -30,10 +30,28 @@ #include <linux/iio/buffer.h> #include <linux/iio/kfifo_buf.h> +#include <linux/dmaengine.h> +#include <linux/dma-mapping.h> + +#define DMA_BUFFER_SIZE SZ_2K + +struct tiadc_dma { + struct dma_slave_config conf; + struct dma_chan *chan; + dma_addr_t addr; + dma_cookie_t cookie; + u8 *buf; + int current_period; + int period_size; + u8 fifo_thresh; +}; + struct tiadc_device { struct ti_tscadc_dev *mfd_tscadc; + struct tiadc_dma dma; struct mutex fifo1_lock; /* to protect fifo access */ int channels; + int total_ch_enabled; u8 channel_line[8]; u8 channel_step[8]; int buffer_en_ch_steps; @@ -198,6 +216,67 @@ static irqreturn_t tiadc_worker_h(int irq, void *private) return IRQ_HANDLED; } +static void tiadc_dma_rx_complete(void *param) +{ + struct iio_dev *indio_dev = param; + struct tiadc_device *adc_dev = iio_priv(indio_dev); + struct tiadc_dma *dma = &adc_dev->dma; + u8 *data; + int i; + + data = dma->buf + dma->current_period * dma->period_size; + dma->current_period = 1 - dma->current_period; /* swap the buffer ID */ + + for (i = 0; i < dma->period_size; i += indio_dev->scan_bytes) { + iio_push_to_buffers(indio_dev, data); + data += indio_dev->scan_bytes; + } +} + +static int tiadc_start_dma(struct iio_dev *indio_dev) +{ + struct tiadc_device *adc_dev = iio_priv(indio_dev); + struct tiadc_dma *dma = &adc_dev->dma; + struct dma_async_tx_descriptor *desc; + + dma->current_period = 0; /* We start to fill period 0 */ + /* + * Make the fifo thresh as the multiple of total number of + * channels enabled, so make sure that cyclic DMA period + * length is also a multiple of total number of channels + * enabled. This ensures that no invalid data is reported + * to the stack via iio_push_to_buffers(). + */ + dma->fifo_thresh = rounddown(FIFO1_THRESHOLD + 1, + adc_dev->total_ch_enabled) - 1; + /* Make sure that period length is multiple of fifo thresh level */ + dma->period_size = rounddown(DMA_BUFFER_SIZE / 2, + (dma->fifo_thresh + 1) * sizeof(u16)); + + dma->conf.src_maxburst = dma->fifo_thresh + 1; + dmaengine_slave_config(dma->chan, &dma->conf); + + desc = dmaengine_prep_dma_cyclic(dma->chan, dma->addr, + dma->period_size * 2, + dma->period_size, DMA_DEV_TO_MEM, + DMA_PREP_INTERRUPT); + if (!desc) + return -EBUSY; + + desc->callback = tiadc_dma_rx_complete; + desc->callback_param = indio_dev; + + dma->cookie = dmaengine_submit(desc); + + dma_async_issue_pending(dma->chan); + + tiadc_writel(adc_dev, REG_FIFO1THR, dma->fifo_thresh); + tiadc_writel(adc_dev, REG_DMA1REQ, dma->fifo_thresh); + tiadc_writel(adc_dev, REG_DMAENABLE_SET, DMA_FIFO1); + + return 0; +} + static int tiadc_buffer_preenable(struct iio_dev *indio_dev) { struct tiadc_device *adc_dev = iio_priv(indio_dev); @@ -218,20 +297,30 @@ static int tiadc_buffer_preenable(struct iio_dev *indio_dev) static int tiadc_buffer_postenable(struct iio_dev *indio_dev) { struct tiadc_device *adc_dev = iio_priv(indio_dev); + struct tiadc_dma *dma = &adc_dev->dma; + unsigned int irq_enable; unsigned int enb = 0; u8 bit; tiadc_step_config(indio_dev); - for_each_set_bit(bit, indio_dev->active_scan_mask, adc_dev->channels) + for_each_set_bit(bit, indio_dev->active_scan_mask, adc_dev->channels) { enb |= (get_adc_step_bit(adc_dev, bit) << 1); + adc_dev->total_ch_enabled++; + } adc_dev->buffer_en_ch_steps = enb; + if (dma->chan) + tiadc_start_dma(indio_dev); + am335x_tsc_se_set_cache(adc_dev->mfd_tscadc, enb); tiadc_writel(adc_dev, REG_IRQSTATUS, IRQENB_FIFO1THRES | IRQENB_FIFO1OVRRUN | IRQENB_FIFO1UNDRFLW); - tiadc_writel(adc_dev, REG_IRQENABLE, IRQENB_FIFO1THRES - | IRQENB_FIFO1OVRRUN); + + irq_enable = IRQENB_FIFO1OVRRUN; + if (!dma->chan) + irq_enable |= IRQENB_FIFO1THRES; + tiadc_writel(adc_dev, REG_IRQENABLE, irq_enable); return 0; } @@ -239,12 +328,18 @@ static int tiadc_buffer_postenable(struct iio_dev *indio_dev) static int tiadc_buffer_predisable(struct iio_dev *indio_dev) { struct tiadc_device *adc_dev = iio_priv(indio_dev); + struct tiadc_dma *dma = &adc_dev->dma; int fifo1count, i, read; tiadc_writel(adc_dev, REG_IRQCLR, (IRQENB_FIFO1THRES | IRQENB_FIFO1OVRRUN | IRQENB_FIFO1UNDRFLW)); am335x_tsc_se_clr(adc_dev->mfd_tscadc, adc_dev->buffer_en_ch_steps); adc_dev->buffer_en_ch_steps = 0; + adc_dev->total_ch_enabled = 0; + if (dma->chan) { + tiadc_writel(adc_dev, REG_DMAENABLE_CLEAR, 0x2); + dmaengine_terminate_async(dma->chan); + } /* Flush FIFO of leftover data in the time it takes to disable adc */ fifo1count = tiadc_readl(adc_dev, REG_FIFO1CNT); @@ -430,6 +525,41 @@ static const struct iio_info tiadc_info = { .driver_module = THIS_MODULE, }; +static int tiadc_request_dma(struct platform_device *pdev, + struct tiadc_device *adc_dev) +{ + struct tiadc_dma *dma = &adc_dev->dma; + dma_cap_mask_t mask; + + /* Default slave configuration parameters */ + dma->conf.direction = DMA_DEV_TO_MEM; + dma->conf.src_addr_width = DMA_SLAVE_BUSWIDTH_2_BYTES; + dma->conf.src_addr = adc_dev->mfd_tscadc->tscadc_phys_base + REG_FIFO1; + + dma_cap_zero(mask); + dma_cap_set(DMA_CYCLIC, mask); + + /* Get a channel for RX */ + dma->chan = dma_request_chan(adc_dev->mfd_tscadc->dev, "fifo1"); + if (IS_ERR(dma->chan)) { + int ret = PTR_ERR(dma->chan); + + dma->chan = NULL; + return ret; + } + + /* RX buffer */ + dma->buf = dma_alloc_coherent(dma->chan->device->dev, DMA_BUFFER_SIZE, + &dma->addr, GFP_KERNEL); + if (!dma->buf) + goto err; + + return 0; +err: + dma_release_channel(dma->chan); + return -ENOMEM; +} + static int tiadc_parse_dt(struct platform_device *pdev, struct tiadc_device *adc_dev) { @@ -512,8 +642,14 @@ static int tiadc_probe(struct platform_device *pdev) platform_set_drvdata(pdev, indio_dev); + err = tiadc_request_dma(pdev, adc_dev); + if (err && err == -EPROBE_DEFER) + goto err_dma; + return 0; +err_dma: + iio_device_unregister(indio_dev); err_buffer_unregister: tiadc_iio_buffered_hardware_remove(indio_dev); err_free_channels: @@ -525,8 +661,14 @@ static int tiadc_remove(struct platform_device *pdev) { struct iio_dev *indio_dev = platform_get_drvdata(pdev); struct tiadc_device *adc_dev = iio_priv(indio_dev); + struct tiadc_dma *dma = &adc_dev->dma; u32 step_en; + if (dma->chan) { + dma_free_coherent(dma->chan->device->dev, DMA_BUFFER_SIZE, + dma->buf, dma->addr); + dma_release_channel(dma->chan); + } iio_device_unregister(indio_dev); tiadc_iio_buffered_hardware_remove(indio_dev); tiadc_channels_remove(indio_dev); diff --git a/drivers/iio/common/Kconfig b/drivers/iio/common/Kconfig index 26a6026de614..e108996a9627 100644 --- a/drivers/iio/common/Kconfig +++ b/drivers/iio/common/Kconfig @@ -2,6 +2,7 @@ # IIO common modules # +source "drivers/iio/common/cros_ec_sensors/Kconfig" source "drivers/iio/common/hid-sensors/Kconfig" source "drivers/iio/common/ms_sensors/Kconfig" source "drivers/iio/common/ssp_sensors/Kconfig" diff --git a/drivers/iio/common/Makefile b/drivers/iio/common/Makefile index 585da6a1b188..6fa760e1bdd5 100644 --- a/drivers/iio/common/Makefile +++ b/drivers/iio/common/Makefile @@ -7,6 +7,7 @@ # # When adding new entries keep the list in alphabetical order +obj-y += cros_ec_sensors/ obj-y += hid-sensors/ obj-y += ms_sensors/ obj-y += ssp_sensors/ diff --git a/drivers/iio/common/cros_ec_sensors/Kconfig b/drivers/iio/common/cros_ec_sensors/Kconfig new file mode 100644 index 000000000000..135f6825903f --- /dev/null +++ b/drivers/iio/common/cros_ec_sensors/Kconfig @@ -0,0 +1,22 @@ +# +# Chrome OS Embedded Controller managed sensors library +# +config IIO_CROS_EC_SENSORS_CORE + tristate "ChromeOS EC Sensors Core" + depends on SYSFS && MFD_CROS_EC + select IIO_BUFFER + select IIO_TRIGGERED_BUFFER + help + Base module for the ChromeOS EC Sensors module. + Contains core functions used by other IIO CrosEC sensor + drivers. + Define common attributes and sysfs interrupt handler. + +config IIO_CROS_EC_SENSORS + tristate "ChromeOS EC Contiguous Sensors" + depends on IIO_CROS_EC_SENSORS_CORE + help + Module to handle 3d contiguous sensors like + Accelerometers, Gyroscope and Magnetometer that are + presented by the ChromeOS EC Sensor hub. + Creates an IIO device for each functions. diff --git a/drivers/iio/common/cros_ec_sensors/Makefile b/drivers/iio/common/cros_ec_sensors/Makefile new file mode 100644 index 000000000000..ec716ff2a775 --- /dev/null +++ b/drivers/iio/common/cros_ec_sensors/Makefile @@ -0,0 +1,6 @@ +# +# Makefile for sensors seen through the ChromeOS EC sensor hub. +# + +obj-$(CONFIG_IIO_CROS_EC_SENSORS_CORE) += cros_ec_sensors_core.o +obj-$(CONFIG_IIO_CROS_EC_SENSORS) += cros_ec_sensors.o diff --git a/drivers/iio/common/cros_ec_sensors/cros_ec_sensors.c b/drivers/iio/common/cros_ec_sensors/cros_ec_sensors.c new file mode 100644 index 000000000000..d6c372bb433b --- /dev/null +++ b/drivers/iio/common/cros_ec_sensors/cros_ec_sensors.c @@ -0,0 +1,322 @@ +/* + * cros_ec_sensors - Driver for Chrome OS Embedded Controller sensors. + * + * Copyright (C) 2016 Google, Inc + * + * This software is licensed under the terms of the GNU General Public + * License version 2, as published by the Free Software Foundation, and + * may be copied, distributed, and modified under those terms. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * This driver uses the cros-ec interface to communicate with the Chrome OS + * EC about sensors data. Data access is presented through iio sysfs. + */ + +#include <linux/delay.h> +#include <linux/device.h> +#include <linux/iio/buffer.h> +#include <linux/iio/iio.h> +#include <linux/iio/kfifo_buf.h> +#include <linux/iio/trigger_consumer.h> +#include <linux/iio/triggered_buffer.h> +#include <linux/kernel.h> +#include <linux/mfd/cros_ec.h> +#include <linux/mfd/cros_ec_commands.h> +#include <linux/module.h> +#include <linux/platform_device.h> +#include <linux/slab.h> +#include <linux/sysfs.h> + +#include "cros_ec_sensors_core.h" + +#define CROS_EC_SENSORS_MAX_CHANNELS 4 + +/* State data for ec_sensors iio driver. */ +struct cros_ec_sensors_state { + /* Shared by all sensors */ + struct cros_ec_sensors_core_state core; + + struct iio_chan_spec channels[CROS_EC_SENSORS_MAX_CHANNELS]; +}; + +static int cros_ec_sensors_read(struct iio_dev *indio_dev, + struct iio_chan_spec const *chan, + int *val, int *val2, long mask) +{ + struct cros_ec_sensors_state *st = iio_priv(indio_dev); + s16 data = 0; + s64 val64; + int i; + int ret; + int idx = chan->scan_index; + + mutex_lock(&st->core.cmd_lock); + + switch (mask) { + case IIO_CHAN_INFO_RAW: + ret = st->core.read_ec_sensors_data(indio_dev, 1 << idx, &data); + if (ret < 0) + break; + + *val = data; + break; + case IIO_CHAN_INFO_CALIBBIAS: + st->core.param.cmd = MOTIONSENSE_CMD_SENSOR_OFFSET; + st->core.param.sensor_offset.flags = 0; + + ret = cros_ec_motion_send_host_cmd(&st->core, 0); + if (ret < 0) + break; + + /* Save values */ + for (i = CROS_EC_SENSOR_X; i < CROS_EC_SENSOR_MAX_AXIS; i++) + st->core.calib[i] = + st->core.resp->sensor_offset.offset[i]; + + *val = st->core.calib[idx]; + break; + case IIO_CHAN_INFO_SCALE: + st->core.param.cmd = MOTIONSENSE_CMD_SENSOR_RANGE; + st->core.param.sensor_range.data = EC_MOTION_SENSE_NO_VALUE; + + ret = cros_ec_motion_send_host_cmd(&st->core, 0); + if (ret < 0) + break; + + val64 = st->core.resp->sensor_range.ret; + switch (st->core.type) { + case MOTIONSENSE_TYPE_ACCEL: + /* + * EC returns data in g, iio exepects m/s^2. + * Do not use IIO_G_TO_M_S_2 to avoid precision loss. + */ + *val = div_s64(val64 * 980665, 10); + *val2 = 10000 << (CROS_EC_SENSOR_BITS - 1); + ret = IIO_VAL_FRACTIONAL; + break; + case MOTIONSENSE_TYPE_GYRO: + /* + * EC returns data in dps, iio expects rad/s. + * Do not use IIO_DEGREE_TO_RAD to avoid precision + * loss. Round to the nearest integer. + */ + *val = div_s64(val64 * 314159 + 9000000ULL, 1000); + *val2 = 18000 << (CROS_EC_SENSOR_BITS - 1); + ret = IIO_VAL_FRACTIONAL; + break; + case MOTIONSENSE_TYPE_MAG: + /* + * EC returns data in 16LSB / uT, + * iio expects Gauss + */ + *val = val64; + *val2 = 100 << (CROS_EC_SENSOR_BITS - 1); + ret = IIO_VAL_FRACTIONAL; + break; + default: + ret = -EINVAL; + } + break; + default: + ret = cros_ec_sensors_core_read(&st->core, chan, val, val2, + mask); + break; + } + mutex_unlock(&st->core.cmd_lock); + + return ret; +} + +static int cros_ec_sensors_write(struct iio_dev *indio_dev, + struct iio_chan_spec const *chan, + int val, int val2, long mask) +{ + struct cros_ec_sensors_state *st = iio_priv(indio_dev); + int i; + int ret; + int idx = chan->scan_index; + + mutex_lock(&st->core.cmd_lock); + + switch (mask) { + case IIO_CHAN_INFO_CALIBBIAS: + st->core.calib[idx] = val; + + /* Send to EC for each axis, even if not complete */ + st->core.param.cmd = MOTIONSENSE_CMD_SENSOR_OFFSET; + st->core.param.sensor_offset.flags = + MOTION_SENSE_SET_OFFSET; + for (i = CROS_EC_SENSOR_X; i < CROS_EC_SENSOR_MAX_AXIS; i++) + st->core.param.sensor_offset.offset[i] = + st->core.calib[i]; + st->core.param.sensor_offset.temp = + EC_MOTION_SENSE_INVALID_CALIB_TEMP; + + ret = cros_ec_motion_send_host_cmd(&st->core, 0); + break; + case IIO_CHAN_INFO_SCALE: + if (st->core.type == MOTIONSENSE_TYPE_MAG) { + ret = -EINVAL; + break; + } + st->core.param.cmd = MOTIONSENSE_CMD_SENSOR_RANGE; + st->core.param.sensor_range.data = val; + + /* Always roundup, so caller gets at least what it asks for. */ + st->core.param.sensor_range.roundup = 1; + + ret = cros_ec_motion_send_host_cmd(&st->core, 0); + break; + default: + ret = cros_ec_sensors_core_write( + &st->core, chan, val, val2, mask); + break; + } + + mutex_unlock(&st->core.cmd_lock); + + return ret; +} + +static const struct iio_info ec_sensors_info = { + .read_raw = &cros_ec_sensors_read, + .write_raw = &cros_ec_sensors_write, + .driver_module = THIS_MODULE, +}; + +static int cros_ec_sensors_probe(struct platform_device *pdev) +{ + struct device *dev = &pdev->dev; + struct cros_ec_dev *ec_dev = dev_get_drvdata(dev->parent); + struct cros_ec_device *ec_device; + struct iio_dev *indio_dev; + struct cros_ec_sensors_state *state; + struct iio_chan_spec *channel; + int ret, i; + + if (!ec_dev || !ec_dev->ec_dev) { + dev_warn(&pdev->dev, "No CROS EC device found.\n"); + return -EINVAL; + } + ec_device = ec_dev->ec_dev; + + indio_dev = devm_iio_device_alloc(&pdev->dev, sizeof(*state)); + if (!indio_dev) + return -ENOMEM; + + ret = cros_ec_sensors_core_init(pdev, indio_dev, true); + if (ret) + return ret; + + indio_dev->info = &ec_sensors_info; + state = iio_priv(indio_dev); + for (channel = state->channels, i = CROS_EC_SENSOR_X; + i < CROS_EC_SENSOR_MAX_AXIS; i++, channel++) { + /* Common part */ + channel->info_mask_separate = + BIT(IIO_CHAN_INFO_RAW) | + BIT(IIO_CHAN_INFO_CALIBBIAS); + channel->info_mask_shared_by_all = + BIT(IIO_CHAN_INFO_SCALE) | + BIT(IIO_CHAN_INFO_FREQUENCY) | + BIT(IIO_CHAN_INFO_SAMP_FREQ); + channel->scan_type.realbits = CROS_EC_SENSOR_BITS; + channel->scan_type.storagebits = CROS_EC_SENSOR_BITS; + channel->scan_index = i; + channel->ext_info = cros_ec_sensors_ext_info; + channel->modified = 1; + channel->channel2 = IIO_MOD_X + i; + channel->scan_type.sign = 's'; + + /* Sensor specific */ + switch (state->core.type) { + case MOTIONSENSE_TYPE_ACCEL: + channel->type = IIO_ACCEL; + break; + case MOTIONSENSE_TYPE_GYRO: + channel->type = IIO_ANGL_VEL; + break; + case MOTIONSENSE_TYPE_MAG: + channel->type = IIO_MAGN; + break; + default: + dev_err(&pdev->dev, "Unknown motion sensor\n"); + return -EINVAL; + } + } + + /* Timestamp */ + channel->type = IIO_TIMESTAMP; + channel->channel = -1; + channel->scan_index = CROS_EC_SENSOR_MAX_AXIS; + channel->scan_type.sign = 's'; + channel->scan_type.realbits = 64; + channel->scan_type.storagebits = 64; + + indio_dev->channels = state->channels; + indio_dev->num_channels = CROS_EC_SENSORS_MAX_CHANNELS; + + /* There is only enough room for accel and gyro in the io space */ + if ((state->core.ec->cmd_readmem != NULL) && + (state->core.type != MOTIONSENSE_TYPE_MAG)) + state->core.read_ec_sensors_data = cros_ec_sensors_read_lpc; + else + state->core.read_ec_sensors_data = cros_ec_sensors_read_cmd; + + ret = iio_triggered_buffer_setup(indio_dev, NULL, + cros_ec_sensors_capture, NULL); + if (ret) + return ret; + + ret = iio_device_register(indio_dev); + if (ret) + goto error_uninit_buffer; + + return 0; + +error_uninit_buffer: + iio_triggered_buffer_cleanup(indio_dev); + + return ret; +} + +static int cros_ec_sensors_remove(struct platform_device *pdev) +{ + struct iio_dev *indio_dev = platform_get_drvdata(pdev); + + iio_device_unregister(indio_dev); + iio_triggered_buffer_cleanup(indio_dev); + + return 0; +} + +static const struct platform_device_id cros_ec_sensors_ids[] = { + { + .name = "cros-ec-accel", + }, + { + .name = "cros-ec-gyro", + }, + { + .name = "cros-ec-mag", + }, + { /* sentinel */ } +}; +MODULE_DEVICE_TABLE(platform, cros_ec_sensors_ids); + +static struct platform_driver cros_ec_sensors_platform_driver = { + .driver = { + .name = "cros-ec-sensors", + }, + .probe = cros_ec_sensors_probe, + .remove = cros_ec_sensors_remove, + .id_table = cros_ec_sensors_ids, +}; +module_platform_driver(cros_ec_sensors_platform_driver); + +MODULE_DESCRIPTION("ChromeOS EC 3-axis sensors driver"); +MODULE_LICENSE("GPL v2"); diff --git a/drivers/iio/common/cros_ec_sensors/cros_ec_sensors_core.c b/drivers/iio/common/cros_ec_sensors/cros_ec_sensors_core.c new file mode 100644 index 000000000000..a3be7991355e --- /dev/null +++ b/drivers/iio/common/cros_ec_sensors/cros_ec_sensors_core.c @@ -0,0 +1,450 @@ +/* + * cros_ec_sensors_core - Common function for Chrome OS EC sensor driver. + * + * Copyright (C) 2016 Google, Inc + * + * This software is licensed under the terms of the GNU General Public + * License version 2, as published by the Free Software Foundation, and + * may be copied, distributed, and modified under those terms. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + */ + +#include <linux/delay.h> +#include <linux/device.h> +#include <linux/iio/buffer.h> +#include <linux/iio/iio.h> +#include <linux/iio/kfifo_buf.h> +#include <linux/iio/trigger_consumer.h> +#include <linux/kernel.h> +#include <linux/mfd/cros_ec.h> +#include <linux/mfd/cros_ec_commands.h> +#include <linux/module.h> +#include <linux/slab.h> +#include <linux/sysfs.h> +#include <linux/platform_device.h> + +#include "cros_ec_sensors_core.h" + +static char *cros_ec_loc[] = { + [MOTIONSENSE_LOC_BASE] = "base", + [MOTIONSENSE_LOC_LID] = "lid", + [MOTIONSENSE_LOC_MAX] = "unknown", +}; + +int cros_ec_sensors_core_init(struct platform_device *pdev, + struct iio_dev *indio_dev, + bool physical_device) +{ + struct device *dev = &pdev->dev; + struct cros_ec_sensors_core_state *state = iio_priv(indio_dev); + struct cros_ec_dev *ec = dev_get_drvdata(pdev->dev.parent); + struct cros_ec_sensor_platform *sensor_platform = dev_get_platdata(dev); + + platform_set_drvdata(pdev, indio_dev); + + state->ec = ec->ec_dev; + state->msg = devm_kzalloc(&pdev->dev, + max((u16)sizeof(struct ec_params_motion_sense), + state->ec->max_response), GFP_KERNEL); + if (!state->msg) + return -ENOMEM; + + state->resp = (struct ec_response_motion_sense *)state->msg->data; + + mutex_init(&state->cmd_lock); + + /* Set up the host command structure. */ + state->msg->version = 2; + state->msg->command = EC_CMD_MOTION_SENSE_CMD + ec->cmd_offset; + state->msg->outsize = sizeof(struct ec_params_motion_sense); + + indio_dev->dev.parent = &pdev->dev; + indio_dev->name = pdev->name; + + if (physical_device) { + indio_dev->modes = INDIO_DIRECT_MODE; + + state->param.cmd = MOTIONSENSE_CMD_INFO; + state->param.info.sensor_num = sensor_platform->sensor_num; + if (cros_ec_motion_send_host_cmd(state, 0)) { + dev_warn(dev, "Can not access sensor info\n"); + return -EIO; + } + state->type = state->resp->info.type; + state->loc = state->resp->info.location; + } + + return 0; +} +EXPORT_SYMBOL_GPL(cros_ec_sensors_core_init); + +int cros_ec_motion_send_host_cmd(struct cros_ec_sensors_core_state *state, + u16 opt_length) +{ + int ret; + + if (opt_length) + state->msg->insize = min(opt_length, state->ec->max_response); + else + state->msg->insize = state->ec->max_response; + + memcpy(state->msg->data, &state->param, sizeof(state->param)); + + ret = cros_ec_cmd_xfer_status(state->ec, state->msg); + if (ret < 0) + return -EIO; + + if (ret && + state->resp != (struct ec_response_motion_sense *)state->msg->data) + memcpy(state->resp, state->msg->data, ret); + + return 0; +} +EXPORT_SYMBOL_GPL(cros_ec_motion_send_host_cmd); + +static ssize_t cros_ec_sensors_calibrate(struct iio_dev *indio_dev, + uintptr_t private, const struct iio_chan_spec *chan, + const char *buf, size_t len) +{ + struct cros_ec_sensors_core_state *st = iio_priv(indio_dev); + int ret, i; + bool calibrate; + + ret = strtobool(buf, &calibrate); + if (ret < 0) + return ret; + if (!calibrate) + return -EINVAL; + + mutex_lock(&st->cmd_lock); + st->param.cmd = MOTIONSENSE_CMD_PERFORM_CALIB; + ret = cros_ec_motion_send_host_cmd(st, 0); + if (ret != 0) { + dev_warn(&indio_dev->dev, "Unable to calibrate sensor\n"); + } else { + /* Save values */ + for (i = CROS_EC_SENSOR_X; i < CROS_EC_SENSOR_MAX_AXIS; i++) + st->calib[i] = st->resp->perform_calib.offset[i]; + } + mutex_unlock(&st->cmd_lock); + + return ret ? ret : len; +} + +static ssize_t cros_ec_sensors_loc(struct iio_dev *indio_dev, + uintptr_t private, const struct iio_chan_spec *chan, + char *buf) +{ + struct cros_ec_sensors_core_state *st = iio_priv(indio_dev); + + return snprintf(buf, PAGE_SIZE, "%s\n", cros_ec_loc[st->loc]); +} + +const struct iio_chan_spec_ext_info cros_ec_sensors_ext_info[] = { + { + .name = "calibrate", + .shared = IIO_SHARED_BY_ALL, + .write = cros_ec_sensors_calibrate + }, + { + .name = "location", + .shared = IIO_SHARED_BY_ALL, + .read = cros_ec_sensors_loc + }, + { }, +}; +EXPORT_SYMBOL_GPL(cros_ec_sensors_ext_info); + +/** + * cros_ec_sensors_idx_to_reg - convert index into offset in shared memory + * @st: pointer to state information for device + * @idx: sensor index (should be element of enum sensor_index) + * + * Return: address to read at + */ +static unsigned int cros_ec_sensors_idx_to_reg( + struct cros_ec_sensors_core_state *st, + unsigned int idx) +{ + /* + * When using LPC interface, only space for 2 Accel and one Gyro. + * First halfword of MOTIONSENSE_TYPE_ACCEL is used by angle. + */ + if (st->type == MOTIONSENSE_TYPE_ACCEL) + return EC_MEMMAP_ACC_DATA + sizeof(u16) * + (1 + idx + st->param.info.sensor_num * + CROS_EC_SENSOR_MAX_AXIS); + + return EC_MEMMAP_GYRO_DATA + sizeof(u16) * idx; +} + +static int cros_ec_sensors_cmd_read_u8(struct cros_ec_device *ec, + unsigned int offset, u8 *dest) +{ + return ec->cmd_readmem(ec, offset, 1, dest); +} + +static int cros_ec_sensors_cmd_read_u16(struct cros_ec_device *ec, + unsigned int offset, u16 *dest) +{ + __le16 tmp; + int ret = ec->cmd_readmem(ec, offset, 2, &tmp); + + if (ret >= 0) + *dest = le16_to_cpu(tmp); + + return ret; +} + +/** + * cros_ec_sensors_read_until_not_busy() - read until is not busy + * + * @st: pointer to state information for device + * + * Read from EC status byte until it reads not busy. + * Return: 8-bit status if ok, -errno on failure. + */ +static int cros_ec_sensors_read_until_not_busy( + struct cros_ec_sensors_core_state *st) +{ + struct cros_ec_device *ec = st->ec; + u8 status; + int ret, attempts = 0; + + ret = cros_ec_sensors_cmd_read_u8(ec, EC_MEMMAP_ACC_STATUS, &status); + if (ret < 0) + return ret; + + while (status & EC_MEMMAP_ACC_STATUS_BUSY_BIT) { + /* Give up after enough attempts, return error. */ + if (attempts++ >= 50) + return -EIO; + + /* Small delay every so often. */ + if (attempts % 5 == 0) + msleep(25); + + ret = cros_ec_sensors_cmd_read_u8(ec, EC_MEMMAP_ACC_STATUS, + &status); + if (ret < 0) + return ret; + } + + return status; +} + +/** + * read_ec_sensors_data_unsafe() - read acceleration data from EC shared memory + * @indio_dev: pointer to IIO device + * @scan_mask: bitmap of the sensor indices to scan + * @data: location to store data + * + * This is the unsafe function for reading the EC data. It does not guarantee + * that the EC will not modify the data as it is being read in. + * + * Return: 0 on success, -errno on failure. + */ +static int cros_ec_sensors_read_data_unsafe(struct iio_dev *indio_dev, + unsigned long scan_mask, s16 *data) +{ + struct cros_ec_sensors_core_state *st = iio_priv(indio_dev); + struct cros_ec_device *ec = st->ec; + unsigned int i; + int ret; + + /* Read all sensors enabled in scan_mask. Each value is 2 bytes. */ + for_each_set_bit(i, &scan_mask, indio_dev->masklength) { + ret = cros_ec_sensors_cmd_read_u16(ec, + cros_ec_sensors_idx_to_reg(st, i), + data); + if (ret < 0) + return ret; + + data++; + } + + return 0; +} + +int cros_ec_sensors_read_lpc(struct iio_dev *indio_dev, + unsigned long scan_mask, s16 *data) +{ + struct cros_ec_sensors_core_state *st = iio_priv(indio_dev); + struct cros_ec_device *ec = st->ec; + u8 samp_id = 0xff, status = 0; + int ret, attempts = 0; + + /* + * Continually read all data from EC until the status byte after + * all reads reflects that the EC is not busy and the sample id + * matches the sample id from before all reads. This guarantees + * that data read in was not modified by the EC while reading. + */ + while ((status & (EC_MEMMAP_ACC_STATUS_BUSY_BIT | + EC_MEMMAP_ACC_STATUS_SAMPLE_ID_MASK)) != samp_id) { + /* If we have tried to read too many times, return error. */ + if (attempts++ >= 5) + return -EIO; + + /* Read status byte until EC is not busy. */ + status = cros_ec_sensors_read_until_not_busy(st); + if (status < 0) + return status; + + /* + * Store the current sample id so that we can compare to the + * sample id after reading the data. + */ + samp_id = status & EC_MEMMAP_ACC_STATUS_SAMPLE_ID_MASK; + + /* Read all EC data, format it, and store it into data. */ + ret = cros_ec_sensors_read_data_unsafe(indio_dev, scan_mask, + data); + if (ret < 0) + return ret; + + /* Read status byte. */ + ret = cros_ec_sensors_cmd_read_u8(ec, EC_MEMMAP_ACC_STATUS, + &status); + if (ret < 0) + return ret; + } + + return 0; +} +EXPORT_SYMBOL_GPL(cros_ec_sensors_read_lpc); + +int cros_ec_sensors_read_cmd(struct iio_dev *indio_dev, + unsigned long scan_mask, s16 *data) +{ + struct cros_ec_sensors_core_state *st = iio_priv(indio_dev); + int ret; + unsigned int i; + + /* Read all sensor data through a command. */ + st->param.cmd = MOTIONSENSE_CMD_DATA; + ret = cros_ec_motion_send_host_cmd(st, sizeof(st->resp->data)); + if (ret != 0) { + dev_warn(&indio_dev->dev, "Unable to read sensor data\n"); + return ret; + } + + for_each_set_bit(i, &scan_mask, indio_dev->masklength) { + *data = st->resp->data.data[i]; + data++; + } + + return 0; +} +EXPORT_SYMBOL_GPL(cros_ec_sensors_read_cmd); + +irqreturn_t cros_ec_sensors_capture(int irq, void *p) +{ + struct iio_poll_func *pf = p; + struct iio_dev *indio_dev = pf->indio_dev; + struct cros_ec_sensors_core_state *st = iio_priv(indio_dev); + int ret; + + mutex_lock(&st->cmd_lock); + + /* Clear capture data. */ + memset(st->samples, 0, indio_dev->scan_bytes); + + /* Read data based on which channels are enabled in scan mask. */ + ret = st->read_ec_sensors_data(indio_dev, + *(indio_dev->active_scan_mask), + (s16 *)st->samples); + if (ret < 0) + goto done; + + iio_push_to_buffers_with_timestamp(indio_dev, st->samples, + iio_get_time_ns(indio_dev)); + +done: + /* + * Tell the core we are done with this trigger and ready for the + * next one. + */ + iio_trigger_notify_done(indio_dev->trig); + + mutex_unlock(&st->cmd_lock); + + return IRQ_HANDLED; +} +EXPORT_SYMBOL_GPL(cros_ec_sensors_capture); + +int cros_ec_sensors_core_read(struct cros_ec_sensors_core_state *st, + struct iio_chan_spec const *chan, + int *val, int *val2, long mask) +{ + int ret = IIO_VAL_INT; + + switch (mask) { + case IIO_CHAN_INFO_SAMP_FREQ: + st->param.cmd = MOTIONSENSE_CMD_EC_RATE; + st->param.ec_rate.data = + EC_MOTION_SENSE_NO_VALUE; + + if (cros_ec_motion_send_host_cmd(st, 0)) + ret = -EIO; + else + *val = st->resp->ec_rate.ret; + break; + case IIO_CHAN_INFO_FREQUENCY: + st->param.cmd = MOTIONSENSE_CMD_SENSOR_ODR; + st->param.sensor_odr.data = + EC_MOTION_SENSE_NO_VALUE; + + if (cros_ec_motion_send_host_cmd(st, 0)) + ret = -EIO; + else + *val = st->resp->sensor_odr.ret; + break; + default: + break; + } + + return ret; +} +EXPORT_SYMBOL_GPL(cros_ec_sensors_core_read); + +int cros_ec_sensors_core_write(struct cros_ec_sensors_core_state *st, + struct iio_chan_spec const *chan, + int val, int val2, long mask) +{ + int ret = 0; + + switch (mask) { + case IIO_CHAN_INFO_FREQUENCY: + st->param.cmd = MOTIONSENSE_CMD_SENSOR_ODR; + st->param.sensor_odr.data = val; + + /* Always roundup, so caller gets at least what it asks for. */ + st->param.sensor_odr.roundup = 1; + + if (cros_ec_motion_send_host_cmd(st, 0)) + ret = -EIO; + break; + case IIO_CHAN_INFO_SAMP_FREQ: + st->param.cmd = MOTIONSENSE_CMD_EC_RATE; + st->param.ec_rate.data = val; + + if (cros_ec_motion_send_host_cmd(st, 0)) + ret = -EIO; + else + st->curr_sampl_freq = val; + break; + default: + ret = -EINVAL; + break; + } + return ret; +} +EXPORT_SYMBOL_GPL(cros_ec_sensors_core_write); + +MODULE_DESCRIPTION("ChromeOS EC sensor hub core functions"); +MODULE_LICENSE("GPL v2"); diff --git a/drivers/iio/common/cros_ec_sensors/cros_ec_sensors_core.h b/drivers/iio/common/cros_ec_sensors/cros_ec_sensors_core.h new file mode 100644 index 000000000000..8bc2ca3c2e2e --- /dev/null +++ b/drivers/iio/common/cros_ec_sensors/cros_ec_sensors_core.h @@ -0,0 +1,175 @@ +/* + * ChromeOS EC sensor hub + * + * Copyright (C) 2016 Google, Inc + * + * This software is licensed under the terms of the GNU General Public + * License version 2, as published by the Free Software Foundation, and + * may be copied, distributed, and modified under those terms. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + */ + +#ifndef __CROS_EC_SENSORS_CORE_H +#define __CROS_EC_SENSORS_CORE_H + +#include <linux/irqreturn.h> + +enum { + CROS_EC_SENSOR_X, + CROS_EC_SENSOR_Y, + CROS_EC_SENSOR_Z, + CROS_EC_SENSOR_MAX_AXIS, +}; + +/* EC returns sensor values using signed 16 bit registers */ +#define CROS_EC_SENSOR_BITS 16 + +/* + * 4 16 bit channels are allowed. + * Good enough for current sensors, they use up to 3 16 bit vectors. + */ +#define CROS_EC_SAMPLE_SIZE (sizeof(s64) * 2) + +/* Minimum sampling period to use when device is suspending */ +#define CROS_EC_MIN_SUSPEND_SAMPLING_FREQUENCY 1000 /* 1 second */ + +/** + * struct cros_ec_sensors_core_state - state data for EC sensors IIO driver + * @ec: cros EC device structure + * @cmd_lock: lock used to prevent simultaneous access to the + * commands. + * @msg: cros EC command structure + * @param: motion sensor parameters structure + * @resp: motion sensor response structure + * @type: type of motion sensor + * @loc: location where the motion sensor is placed + * @calib: calibration parameters. Note that trigger + * captured data will always provide the calibrated + * data + * @samples: static array to hold data from a single capture. + * For each channel we need 2 bytes, except for + * the timestamp. The timestamp is always last and + * is always 8-byte aligned. + * @read_ec_sensors_data: function used for accessing sensors values + * @cuur_sampl_freq: current sampling period + */ +struct cros_ec_sensors_core_state { + struct cros_ec_device *ec; + struct mutex cmd_lock; + + struct cros_ec_command *msg; + struct ec_params_motion_sense param; + struct ec_response_motion_sense *resp; + + enum motionsensor_type type; + enum motionsensor_location loc; + + s16 calib[CROS_EC_SENSOR_MAX_AXIS]; + + u8 samples[CROS_EC_SAMPLE_SIZE]; + + int (*read_ec_sensors_data)(struct iio_dev *indio_dev, + unsigned long scan_mask, s16 *data); + + int curr_sampl_freq; +}; + +/** + * cros_ec_sensors_read_lpc() - retrieve data from EC shared memory + * @indio_dev: pointer to IIO device + * @scan_mask: bitmap of the sensor indices to scan + * @data: location to store data + * + * This is the safe function for reading the EC data. It guarantees that the + * data sampled was not modified by the EC while being read. + * + * Return: 0 on success, -errno on failure. + */ +int cros_ec_sensors_read_lpc(struct iio_dev *indio_dev, unsigned long scan_mask, + s16 *data); + +/** + * cros_ec_sensors_read_cmd() - retrieve data using the EC command protocol + * @indio_dev: pointer to IIO device + * @scan_mask: bitmap of the sensor indices to scan + * @data: location to store data + * + * Return: 0 on success, -errno on failure. + */ +int cros_ec_sensors_read_cmd(struct iio_dev *indio_dev, unsigned long scan_mask, + s16 *data); + +/** + * cros_ec_sensors_core_init() - basic initialization of the core structure + * @pdev: platform device created for the sensors + * @indio_dev: iio device structure of the device + * @physical_device: true if the device refers to a physical device + * + * Return: 0 on success, -errno on failure. + */ +int cros_ec_sensors_core_init(struct platform_device *pdev, + struct iio_dev *indio_dev, bool physical_device); + +/** + * cros_ec_sensors_capture() - the trigger handler function + * @irq: the interrupt number. + * @p: a pointer to the poll function. + * + * On a trigger event occurring, if the pollfunc is attached then this + * handler is called as a threaded interrupt (and hence may sleep). It + * is responsible for grabbing data from the device and pushing it into + * the associated buffer. + * + * Return: IRQ_HANDLED + */ +irqreturn_t cros_ec_sensors_capture(int irq, void *p); + +/** + * cros_ec_motion_send_host_cmd() - send motion sense host command + * @st: pointer to state information for device + * @opt_length: optional length to reduce the response size, useful on the data + * path. Otherwise, the maximal allowed response size is used + * + * When called, the sub-command is assumed to be set in param->cmd. + * + * Return: 0 on success, -errno on failure. + */ +int cros_ec_motion_send_host_cmd(struct cros_ec_sensors_core_state *st, + u16 opt_length); + +/** + * cros_ec_sensors_core_read() - function to request a value from the sensor + * @st: pointer to state information for device + * @chan: channel specification structure table + * @val: will contain one element making up the returned value + * @val2: will contain another element making up the returned value + * @mask: specifies which values to be requested + * + * Return: the type of value returned by the device + */ +int cros_ec_sensors_core_read(struct cros_ec_sensors_core_state *st, + struct iio_chan_spec const *chan, + int *val, int *val2, long mask); + +/** + * cros_ec_sensors_core_write() - function to write a value to the sensor + * @st: pointer to state information for device + * @chan: channel specification structure table + * @val: first part of value to write + * @val2: second part of value to write + * @mask: specifies which values to write + * + * Return: the type of value returned by the device + */ +int cros_ec_sensors_core_write(struct cros_ec_sensors_core_state *st, + struct iio_chan_spec const *chan, + int val, int val2, long mask); + +/* List of extended channel specification for all sensors */ +extern const struct iio_chan_spec_ext_info cros_ec_sensors_ext_info[]; + +#endif /* __CROS_EC_SENSORS_CORE_H */ diff --git a/drivers/iio/common/hid-sensors/hid-sensor-attributes.c b/drivers/iio/common/hid-sensors/hid-sensor-attributes.c index dc33c1dd5191..4509f8475c54 100644 --- a/drivers/iio/common/hid-sensors/hid-sensor-attributes.c +++ b/drivers/iio/common/hid-sensors/hid-sensor-attributes.c @@ -201,7 +201,7 @@ int hid_sensor_write_samp_freq_value(struct hid_sensor_common *st, int ret; if (val1 < 0 || val2 < 0) - ret = -EINVAL; + return -EINVAL; value = val1 * pow_10(6) + val2; if (value) { @@ -250,6 +250,9 @@ int hid_sensor_write_raw_hyst_value(struct hid_sensor_common *st, s32 value; int ret; + if (val1 < 0 || val2 < 0) + return -EINVAL; + value = convert_to_vtf_format(st->sensitivity.size, st->sensitivity.unit_expo, val1, val2); diff --git a/drivers/iio/gyro/Kconfig b/drivers/iio/gyro/Kconfig index 205a84420ae9..107b5efd4178 100644 --- a/drivers/iio/gyro/Kconfig +++ b/drivers/iio/gyro/Kconfig @@ -84,6 +84,23 @@ config HID_SENSOR_GYRO_3D Say yes here to build support for the HID SENSOR Gyroscope 3D. +config MPU3050 + tristate + select IIO_BUFFER + select IIO_TRIGGERED_BUFFER + select REGMAP + +config MPU3050_I2C + tristate "Invensense MPU3050 devices on I2C" + depends on !(INPUT_MPU3050=y || INPUT_MPU3050=m) + select MPU3050 + select REGMAP_I2C + select I2C_MUX + help + This driver supports the Invensense MPU3050 gyroscope over I2C. + This driver can be built as a module. The module will be called + inv-mpu3050-i2c. + config IIO_ST_GYRO_3AXIS tristate "STMicroelectronics gyroscopes 3-Axis Driver" depends on (I2C || SPI_MASTER) && SYSFS diff --git a/drivers/iio/gyro/Makefile b/drivers/iio/gyro/Makefile index f866a4be0667..f0e149a606b0 100644 --- a/drivers/iio/gyro/Makefile +++ b/drivers/iio/gyro/Makefile @@ -14,6 +14,11 @@ obj-$(CONFIG_BMG160_SPI) += bmg160_spi.o obj-$(CONFIG_HID_SENSOR_GYRO_3D) += hid-sensor-gyro-3d.o +# Currently this is rolled into one module, split it if +# we ever create a separate SPI interface for MPU-3050 +obj-$(CONFIG_MPU3050) += mpu3050.o +mpu3050-objs := mpu3050-core.o mpu3050-i2c.o + itg3200-y := itg3200_core.o itg3200-$(CONFIG_IIO_BUFFER) += itg3200_buffer.o obj-$(CONFIG_ITG3200) += itg3200.o diff --git a/drivers/iio/gyro/mpu3050-core.c b/drivers/iio/gyro/mpu3050-core.c new file mode 100644 index 000000000000..ed681c70a7b4 --- /dev/null +++ b/drivers/iio/gyro/mpu3050-core.c @@ -0,0 +1,1307 @@ +/* + * MPU3050 gyroscope driver + * + * Copyright (C) 2016 Linaro Ltd. + * Author: Linus Walleij <linus.walleij@linaro.org> + * + * Based on the input subsystem driver, Copyright (C) 2011 Wistron Co.Ltd + * Joseph Lai <joseph_lai@wistron.com> and trimmed down by + * Alan Cox <alan@linux.intel.com> in turn based on bma023.c. + * Device behaviour based on a misc driver posted by Nathan Royer in 2011. + * + * TODO: add support for setting up the low pass 3dB frequency. + */ + +#include <linux/bitops.h> +#include <linux/delay.h> +#include <linux/err.h> +#include <linux/iio/buffer.h> +#include <linux/iio/iio.h> +#include <linux/iio/sysfs.h> +#include <linux/iio/trigger.h> +#include <linux/iio/trigger_consumer.h> +#include <linux/iio/triggered_buffer.h> +#include <linux/interrupt.h> +#include <linux/module.h> +#include <linux/pm_runtime.h> +#include <linux/random.h> +#include <linux/slab.h> + +#include "mpu3050.h" + +#define MPU3050_CHIP_ID 0x69 + +/* + * Register map: anything suffixed *_H is a big-endian high byte and always + * followed by the corresponding low byte (*_L) even though these are not + * explicitly included in the register definitions. + */ +#define MPU3050_CHIP_ID_REG 0x00 +#define MPU3050_PRODUCT_ID_REG 0x01 +#define MPU3050_XG_OFFS_TC 0x05 +#define MPU3050_YG_OFFS_TC 0x08 +#define MPU3050_ZG_OFFS_TC 0x0B +#define MPU3050_X_OFFS_USR_H 0x0C +#define MPU3050_Y_OFFS_USR_H 0x0E +#define MPU3050_Z_OFFS_USR_H 0x10 +#define MPU3050_FIFO_EN 0x12 +#define MPU3050_AUX_VDDIO 0x13 +#define MPU3050_SLV_ADDR 0x14 +#define MPU3050_SMPLRT_DIV 0x15 +#define MPU3050_DLPF_FS_SYNC 0x16 +#define MPU3050_INT_CFG 0x17 +#define MPU3050_AUX_ADDR 0x18 +#define MPU3050_INT_STATUS 0x1A +#define MPU3050_TEMP_H 0x1B +#define MPU3050_XOUT_H 0x1D +#define MPU3050_YOUT_H 0x1F +#define MPU3050_ZOUT_H 0x21 +#define MPU3050_DMP_CFG1 0x35 +#define MPU3050_DMP_CFG2 0x36 +#define MPU3050_BANK_SEL 0x37 +#define MPU3050_MEM_START_ADDR 0x38 +#define MPU3050_MEM_R_W 0x39 +#define MPU3050_FIFO_COUNT_H 0x3A +#define MPU3050_FIFO_R 0x3C +#define MPU3050_USR_CTRL 0x3D +#define MPU3050_PWR_MGM 0x3E + +/* MPU memory bank read options */ +#define MPU3050_MEM_PRFTCH BIT(5) +#define MPU3050_MEM_USER_BANK BIT(4) +/* Bits 8-11 select memory bank */ +#define MPU3050_MEM_RAM_BANK_0 0 +#define MPU3050_MEM_RAM_BANK_1 1 +#define MPU3050_MEM_RAM_BANK_2 2 +#define MPU3050_MEM_RAM_BANK_3 3 +#define MPU3050_MEM_OTP_BANK_0 4 + +#define MPU3050_AXIS_REGS(axis) (MPU3050_XOUT_H + (axis * 2)) + +/* Register bits */ + +/* FIFO Enable */ +#define MPU3050_FIFO_EN_FOOTER BIT(0) +#define MPU3050_FIFO_EN_AUX_ZOUT BIT(1) +#define MPU3050_FIFO_EN_AUX_YOUT BIT(2) +#define MPU3050_FIFO_EN_AUX_XOUT BIT(3) +#define MPU3050_FIFO_EN_GYRO_ZOUT BIT(4) +#define MPU3050_FIFO_EN_GYRO_YOUT BIT(5) +#define MPU3050_FIFO_EN_GYRO_XOUT BIT(6) +#define MPU3050_FIFO_EN_TEMP_OUT BIT(7) + +/* + * Digital Low Pass filter (DLPF) + * Full Scale (FS) + * and Synchronization + */ +#define MPU3050_EXT_SYNC_NONE 0x00 +#define MPU3050_EXT_SYNC_TEMP 0x20 +#define MPU3050_EXT_SYNC_GYROX 0x40 +#define MPU3050_EXT_SYNC_GYROY 0x60 +#define MPU3050_EXT_SYNC_GYROZ 0x80 +#define MPU3050_EXT_SYNC_ACCELX 0xA0 +#define MPU3050_EXT_SYNC_ACCELY 0xC0 +#define MPU3050_EXT_SYNC_ACCELZ 0xE0 +#define MPU3050_EXT_SYNC_MASK 0xE0 +#define MPU3050_EXT_SYNC_SHIFT 5 + +#define MPU3050_FS_250DPS 0x00 +#define MPU3050_FS_500DPS 0x08 +#define MPU3050_FS_1000DPS 0x10 +#define MPU3050_FS_2000DPS 0x18 +#define MPU3050_FS_MASK 0x18 +#define MPU3050_FS_SHIFT 3 + +#define MPU3050_DLPF_CFG_256HZ_NOLPF2 0x00 +#define MPU3050_DLPF_CFG_188HZ 0x01 +#define MPU3050_DLPF_CFG_98HZ 0x02 +#define MPU3050_DLPF_CFG_42HZ 0x03 +#define MPU3050_DLPF_CFG_20HZ 0x04 +#define MPU3050_DLPF_CFG_10HZ 0x05 +#define MPU3050_DLPF_CFG_5HZ 0x06 +#define MPU3050_DLPF_CFG_2100HZ_NOLPF 0x07 +#define MPU3050_DLPF_CFG_MASK 0x07 +#define MPU3050_DLPF_CFG_SHIFT 0 + +/* Interrupt config */ +#define MPU3050_INT_RAW_RDY_EN BIT(0) +#define MPU3050_INT_DMP_DONE_EN BIT(1) +#define MPU3050_INT_MPU_RDY_EN BIT(2) +#define MPU3050_INT_ANYRD_2CLEAR BIT(4) +#define MPU3050_INT_LATCH_EN BIT(5) +#define MPU3050_INT_OPEN BIT(6) +#define MPU3050_INT_ACTL BIT(7) +/* Interrupt status */ +#define MPU3050_INT_STATUS_RAW_RDY BIT(0) +#define MPU3050_INT_STATUS_DMP_DONE BIT(1) +#define MPU3050_INT_STATUS_MPU_RDY BIT(2) +#define MPU3050_INT_STATUS_FIFO_OVFLW BIT(7) +/* USR_CTRL */ +#define MPU3050_USR_CTRL_FIFO_EN BIT(6) +#define MPU3050_USR_CTRL_AUX_IF_EN BIT(5) +#define MPU3050_USR_CTRL_AUX_IF_RST BIT(3) +#define MPU3050_USR_CTRL_FIFO_RST BIT(1) +#define MPU3050_USR_CTRL_GYRO_RST BIT(0) +/* PWR_MGM */ +#define MPU3050_PWR_MGM_PLL_X 0x01 +#define MPU3050_PWR_MGM_PLL_Y 0x02 +#define MPU3050_PWR_MGM_PLL_Z 0x03 +#define MPU3050_PWR_MGM_CLKSEL_MASK 0x07 +#define MPU3050_PWR_MGM_STBY_ZG BIT(3) +#define MPU3050_PWR_MGM_STBY_YG BIT(4) +#define MPU3050_PWR_MGM_STBY_XG BIT(5) +#define MPU3050_PWR_MGM_SLEEP BIT(6) +#define MPU3050_PWR_MGM_RESET BIT(7) +#define MPU3050_PWR_MGM_MASK 0xff + +/* + * Fullscale precision is (for finest precision) +/- 250 deg/s, so the full + * scale is actually 500 deg/s. All 16 bits are then used to cover this scale, + * in two's complement. + */ +static unsigned int mpu3050_fs_precision[] = { + IIO_DEGREE_TO_RAD(250), + IIO_DEGREE_TO_RAD(500), + IIO_DEGREE_TO_RAD(1000), + IIO_DEGREE_TO_RAD(2000) +}; + +/* + * Regulator names + */ +static const char mpu3050_reg_vdd[] = "vdd"; +static const char mpu3050_reg_vlogic[] = "vlogic"; + +static unsigned int mpu3050_get_freq(struct mpu3050 *mpu3050) +{ + unsigned int freq; + + if (mpu3050->lpf == MPU3050_DLPF_CFG_256HZ_NOLPF2) + freq = 8000; + else + freq = 1000; + freq /= (mpu3050->divisor + 1); + + return freq; +} + +static int mpu3050_start_sampling(struct mpu3050 *mpu3050) +{ + __be16 raw_val[3]; + int ret; + int i; + + /* Reset */ + ret = regmap_update_bits(mpu3050->map, MPU3050_PWR_MGM, + MPU3050_PWR_MGM_RESET, MPU3050_PWR_MGM_RESET); + if (ret) + return ret; + + /* Turn on the Z-axis PLL */ + ret = regmap_update_bits(mpu3050->map, MPU3050_PWR_MGM, + MPU3050_PWR_MGM_CLKSEL_MASK, + MPU3050_PWR_MGM_PLL_Z); + if (ret) + return ret; + + /* Write calibration offset registers */ + for (i = 0; i < 3; i++) + raw_val[i] = cpu_to_be16(mpu3050->calibration[i]); + + ret = regmap_bulk_write(mpu3050->map, MPU3050_X_OFFS_USR_H, raw_val, + sizeof(raw_val)); + if (ret) + return ret; + + /* Set low pass filter (sample rate), sync and full scale */ + ret = regmap_write(mpu3050->map, MPU3050_DLPF_FS_SYNC, + MPU3050_EXT_SYNC_NONE << MPU3050_EXT_SYNC_SHIFT | + mpu3050->fullscale << MPU3050_FS_SHIFT | + mpu3050->lpf << MPU3050_DLPF_CFG_SHIFT); + if (ret) + return ret; + + /* Set up sampling frequency */ + ret = regmap_write(mpu3050->map, MPU3050_SMPLRT_DIV, mpu3050->divisor); + if (ret) + return ret; + + /* + * Max 50 ms start-up time after setting DLPF_FS_SYNC + * according to the data sheet, then wait for the next sample + * at this frequency T = 1000/f ms. + */ + msleep(50 + 1000 / mpu3050_get_freq(mpu3050)); + + return 0; +} + +static int mpu3050_set_8khz_samplerate(struct mpu3050 *mpu3050) +{ + int ret; + u8 divisor; + enum mpu3050_lpf lpf; + + lpf = mpu3050->lpf; + divisor = mpu3050->divisor; + + mpu3050->lpf = LPF_256_HZ_NOLPF; /* 8 kHz base frequency */ + mpu3050->divisor = 0; /* Divide by 1 */ + ret = mpu3050_start_sampling(mpu3050); + + mpu3050->lpf = lpf; + mpu3050->divisor = divisor; + + return ret; +} + +static int mpu3050_read_raw(struct iio_dev *indio_dev, + struct iio_chan_spec const *chan, + int *val, int *val2, + long mask) +{ + struct mpu3050 *mpu3050 = iio_priv(indio_dev); + int ret; + __be16 raw_val; + + switch (mask) { + case IIO_CHAN_INFO_OFFSET: + switch (chan->type) { + case IIO_TEMP: + /* The temperature scaling is (x+23000)/280 Celsius */ + *val = 23000; + return IIO_VAL_INT; + default: + return -EINVAL; + } + case IIO_CHAN_INFO_CALIBBIAS: + switch (chan->type) { + case IIO_ANGL_VEL: + *val = mpu3050->calibration[chan->scan_index-1]; + return IIO_VAL_INT; + default: + return -EINVAL; + } + case IIO_CHAN_INFO_SAMP_FREQ: + *val = mpu3050_get_freq(mpu3050); + return IIO_VAL_INT; + case IIO_CHAN_INFO_SCALE: + switch (chan->type) { + case IIO_TEMP: + /* Millidegrees, see about temperature scaling above */ + *val = 1000; + *val2 = 280; + return IIO_VAL_FRACTIONAL; + case IIO_ANGL_VEL: + /* + * Convert to the corresponding full scale in + * radians. All 16 bits are used with sign to + * span the available scale: to account for the one + * missing value if we multiply by 1/S16_MAX, instead + * multiply with 2/U16_MAX. + */ + *val = mpu3050_fs_precision[mpu3050->fullscale] * 2; + *val2 = U16_MAX; + return IIO_VAL_FRACTIONAL; + default: + return -EINVAL; + } + case IIO_CHAN_INFO_RAW: + /* Resume device */ + pm_runtime_get_sync(mpu3050->dev); + mutex_lock(&mpu3050->lock); + + ret = mpu3050_set_8khz_samplerate(mpu3050); + if (ret) + goto out_read_raw_unlock; + + switch (chan->type) { + case IIO_TEMP: + ret = regmap_bulk_read(mpu3050->map, MPU3050_TEMP_H, + &raw_val, sizeof(raw_val)); + if (ret) { + dev_err(mpu3050->dev, + "error reading temperature\n"); + goto out_read_raw_unlock; + } + + *val = be16_to_cpu(raw_val); + ret = IIO_VAL_INT; + + goto out_read_raw_unlock; + case IIO_ANGL_VEL: + ret = regmap_bulk_read(mpu3050->map, + MPU3050_AXIS_REGS(chan->scan_index-1), + &raw_val, + sizeof(raw_val)); + if (ret) { + dev_err(mpu3050->dev, + "error reading axis data\n"); + goto out_read_raw_unlock; + } + + *val = be16_to_cpu(raw_val); + ret = IIO_VAL_INT; + + goto out_read_raw_unlock; + default: + ret = -EINVAL; + goto out_read_raw_unlock; + } + default: + break; + } + + return -EINVAL; + +out_read_raw_unlock: + mutex_unlock(&mpu3050->lock); + pm_runtime_mark_last_busy(mpu3050->dev); + pm_runtime_put_autosuspend(mpu3050->dev); + + return ret; +} + +static int mpu3050_write_raw(struct iio_dev *indio_dev, + const struct iio_chan_spec *chan, + int val, int val2, long mask) +{ + struct mpu3050 *mpu3050 = iio_priv(indio_dev); + /* + * Couldn't figure out a way to precalculate these at compile time. + */ + unsigned int fs250 = + DIV_ROUND_CLOSEST(mpu3050_fs_precision[0] * 1000000 * 2, + U16_MAX); + unsigned int fs500 = + DIV_ROUND_CLOSEST(mpu3050_fs_precision[1] * 1000000 * 2, + U16_MAX); + unsigned int fs1000 = + DIV_ROUND_CLOSEST(mpu3050_fs_precision[2] * 1000000 * 2, + U16_MAX); + unsigned int fs2000 = + DIV_ROUND_CLOSEST(mpu3050_fs_precision[3] * 1000000 * 2, + U16_MAX); + + switch (mask) { + case IIO_CHAN_INFO_CALIBBIAS: + if (chan->type != IIO_ANGL_VEL) + return -EINVAL; + mpu3050->calibration[chan->scan_index-1] = val; + return 0; + case IIO_CHAN_INFO_SAMP_FREQ: + /* + * The max samplerate is 8000 Hz, the minimum + * 1000 / 256 ~= 4 Hz + */ + if (val < 4 || val > 8000) + return -EINVAL; + + /* + * Above 1000 Hz we must turn off the digital low pass filter + * so we get a base frequency of 8kHz to the divider + */ + if (val > 1000) { + mpu3050->lpf = LPF_256_HZ_NOLPF; + mpu3050->divisor = DIV_ROUND_CLOSEST(8000, val) - 1; + return 0; + } + + mpu3050->lpf = LPF_188_HZ; + mpu3050->divisor = DIV_ROUND_CLOSEST(1000, val) - 1; + return 0; + case IIO_CHAN_INFO_SCALE: + if (chan->type != IIO_ANGL_VEL) + return -EINVAL; + /* + * We support +/-250, +/-500, +/-1000 and +/2000 deg/s + * which means we need to round to the closest radians + * which will be roughly +/-4.3, +/-8.7, +/-17.5, +/-35 + * rad/s. The scale is then for the 16 bits used to cover + * it 2/(2^16) of that. + */ + + /* Just too large, set the max range */ + if (val != 0) { + mpu3050->fullscale = FS_2000_DPS; + return 0; + } + + /* + * Now we're dealing with fractions below zero in millirad/s + * do some integer interpolation and match with the closest + * fullscale in the table. + */ + if (val2 <= fs250 || + val2 < ((fs500 + fs250) / 2)) + mpu3050->fullscale = FS_250_DPS; + else if (val2 <= fs500 || + val2 < ((fs1000 + fs500) / 2)) + mpu3050->fullscale = FS_500_DPS; + else if (val2 <= fs1000 || + val2 < ((fs2000 + fs1000) / 2)) + mpu3050->fullscale = FS_1000_DPS; + else + /* Catch-all */ + mpu3050->fullscale = FS_2000_DPS; + return 0; + default: + break; + } + + return -EINVAL; +} + +static irqreturn_t mpu3050_trigger_handler(int irq, void *p) +{ + const struct iio_poll_func *pf = p; + struct iio_dev *indio_dev = pf->indio_dev; + struct mpu3050 *mpu3050 = iio_priv(indio_dev); + int ret; + /* + * Temperature 1*16 bits + * Three axes 3*16 bits + * Timestamp 64 bits (4*16 bits) + * Sum total 8*16 bits + */ + __be16 hw_values[8]; + s64 timestamp; + unsigned int datums_from_fifo = 0; + + /* + * If we're using the hardware trigger, get the precise timestamp from + * the top half of the threaded IRQ handler. Otherwise get the + * timestamp here so it will be close in time to the actual values + * read from the registers. + */ + if (iio_trigger_using_own(indio_dev)) + timestamp = mpu3050->hw_timestamp; + else + timestamp = iio_get_time_ns(indio_dev); + + mutex_lock(&mpu3050->lock); + + /* Using the hardware IRQ trigger? Check the buffer then. */ + if (mpu3050->hw_irq_trigger) { + __be16 raw_fifocnt; + u16 fifocnt; + /* X, Y, Z + temperature */ + unsigned int bytes_per_datum = 8; + bool fifo_overflow = false; + + ret = regmap_bulk_read(mpu3050->map, + MPU3050_FIFO_COUNT_H, + &raw_fifocnt, + sizeof(raw_fifocnt)); + if (ret) + goto out_trigger_unlock; + fifocnt = be16_to_cpu(raw_fifocnt); + + if (fifocnt == 512) { + dev_info(mpu3050->dev, + "FIFO overflow! Emptying and resetting FIFO\n"); + fifo_overflow = true; + /* Reset and enable the FIFO */ + ret = regmap_update_bits(mpu3050->map, + MPU3050_USR_CTRL, + MPU3050_USR_CTRL_FIFO_EN | + MPU3050_USR_CTRL_FIFO_RST, + MPU3050_USR_CTRL_FIFO_EN | + MPU3050_USR_CTRL_FIFO_RST); + if (ret) { + dev_info(mpu3050->dev, "error resetting FIFO\n"); + goto out_trigger_unlock; + } + mpu3050->pending_fifo_footer = false; + } + + if (fifocnt) + dev_dbg(mpu3050->dev, + "%d bytes in the FIFO\n", + fifocnt); + + while (!fifo_overflow && fifocnt > bytes_per_datum) { + unsigned int toread; + unsigned int offset; + __be16 fifo_values[5]; + + /* + * If there is a FIFO footer in the pipe, first clear + * that out. This follows the complex algorithm in the + * datasheet that states that you may never leave the + * FIFO empty after the first reading: you have to + * always leave two footer bytes in it. The footer is + * in practice just two zero bytes. + */ + if (mpu3050->pending_fifo_footer) { + toread = bytes_per_datum + 2; + offset = 0; + } else { + toread = bytes_per_datum; + offset = 1; + /* Put in some dummy value */ + fifo_values[0] = 0xAAAA; + } + + ret = regmap_bulk_read(mpu3050->map, + MPU3050_FIFO_R, + &fifo_values[offset], + toread); + + dev_dbg(mpu3050->dev, + "%04x %04x %04x %04x %04x\n", + fifo_values[0], + fifo_values[1], + fifo_values[2], + fifo_values[3], + fifo_values[4]); + + /* Index past the footer (fifo_values[0]) and push */ + iio_push_to_buffers_with_timestamp(indio_dev, + &fifo_values[1], + timestamp); + + fifocnt -= toread; + datums_from_fifo++; + mpu3050->pending_fifo_footer = true; + + /* + * If we're emptying the FIFO, just make sure to + * check if something new appeared. + */ + if (fifocnt < bytes_per_datum) { + ret = regmap_bulk_read(mpu3050->map, + MPU3050_FIFO_COUNT_H, + &raw_fifocnt, + sizeof(raw_fifocnt)); + if (ret) + goto out_trigger_unlock; + fifocnt = be16_to_cpu(raw_fifocnt); + } + + if (fifocnt < bytes_per_datum) + dev_dbg(mpu3050->dev, + "%d bytes left in the FIFO\n", + fifocnt); + + /* + * At this point, the timestamp that triggered the + * hardware interrupt is no longer valid for what + * we are reading (the interrupt likely fired for + * the value on the top of the FIFO), so set the + * timestamp to zero and let userspace deal with it. + */ + timestamp = 0; + } + } + + /* + * If we picked some datums from the FIFO that's enough, else + * fall through and just read from the current value registers. + * This happens in two cases: + * + * - We are using some other trigger (external, like an HRTimer) + * than the sensor's own sample generator. In this case the + * sensor is just set to the max sampling frequency and we give + * the trigger a copy of the latest value every time we get here. + * + * - The hardware trigger is active but unused and we actually use + * another trigger which calls here with a frequency higher + * than what the device provides data. We will then just read + * duplicate values directly from the hardware registers. + */ + if (datums_from_fifo) { + dev_dbg(mpu3050->dev, + "read %d datums from the FIFO\n", + datums_from_fifo); + goto out_trigger_unlock; + } + + ret = regmap_bulk_read(mpu3050->map, MPU3050_TEMP_H, &hw_values, + sizeof(hw_values)); + if (ret) { + dev_err(mpu3050->dev, + "error reading axis data\n"); + goto out_trigger_unlock; + } + + iio_push_to_buffers_with_timestamp(indio_dev, hw_values, timestamp); + +out_trigger_unlock: + mutex_unlock(&mpu3050->lock); + iio_trigger_notify_done(indio_dev->trig); + + return IRQ_HANDLED; +} + +static int mpu3050_buffer_preenable(struct iio_dev *indio_dev) +{ + struct mpu3050 *mpu3050 = iio_priv(indio_dev); + + pm_runtime_get_sync(mpu3050->dev); + + /* Unless we have OUR trigger active, run at full speed */ + if (!mpu3050->hw_irq_trigger) + return mpu3050_set_8khz_samplerate(mpu3050); + + return 0; +} + +static int mpu3050_buffer_postdisable(struct iio_dev *indio_dev) +{ + struct mpu3050 *mpu3050 = iio_priv(indio_dev); + + pm_runtime_mark_last_busy(mpu3050->dev); + pm_runtime_put_autosuspend(mpu3050->dev); + + return 0; +} + +static const struct iio_buffer_setup_ops mpu3050_buffer_setup_ops = { + .preenable = mpu3050_buffer_preenable, + .postenable = iio_triggered_buffer_postenable, + .predisable = iio_triggered_buffer_predisable, + .postdisable = mpu3050_buffer_postdisable, +}; + +static const struct iio_mount_matrix * +mpu3050_get_mount_matrix(const struct iio_dev *indio_dev, + const struct iio_chan_spec *chan) +{ + struct mpu3050 *mpu3050 = iio_priv(indio_dev); + + return &mpu3050->orientation; +} + +static const struct iio_chan_spec_ext_info mpu3050_ext_info[] = { + IIO_MOUNT_MATRIX(IIO_SHARED_BY_TYPE, mpu3050_get_mount_matrix), + { }, +}; + +#define MPU3050_AXIS_CHANNEL(axis, index) \ + { \ + .type = IIO_ANGL_VEL, \ + .modified = 1, \ + .channel2 = IIO_MOD_##axis, \ + .info_mask_separate = BIT(IIO_CHAN_INFO_RAW) | \ + BIT(IIO_CHAN_INFO_CALIBBIAS), \ + .info_mask_shared_by_type = BIT(IIO_CHAN_INFO_SCALE), \ + .info_mask_shared_by_all = BIT(IIO_CHAN_INFO_SAMP_FREQ),\ + .ext_info = mpu3050_ext_info, \ + .scan_index = index, \ + .scan_type = { \ + .sign = 's', \ + .realbits = 16, \ + .storagebits = 16, \ + .endianness = IIO_BE, \ + }, \ + } + +static const struct iio_chan_spec mpu3050_channels[] = { + { + .type = IIO_TEMP, + .info_mask_separate = BIT(IIO_CHAN_INFO_RAW) | + BIT(IIO_CHAN_INFO_SCALE) | + BIT(IIO_CHAN_INFO_OFFSET), + .info_mask_shared_by_all = BIT(IIO_CHAN_INFO_SAMP_FREQ), + .scan_index = 0, + .scan_type = { + .sign = 's', + .realbits = 16, + .storagebits = 16, + .endianness = IIO_BE, + }, + }, + MPU3050_AXIS_CHANNEL(X, 1), + MPU3050_AXIS_CHANNEL(Y, 2), + MPU3050_AXIS_CHANNEL(Z, 3), + IIO_CHAN_SOFT_TIMESTAMP(4), +}; + +/* Four channels apart from timestamp, scan mask = 0x0f */ +static const unsigned long mpu3050_scan_masks[] = { 0xf, 0 }; + +/* + * These are just the hardcoded factors resulting from the more elaborate + * calculations done with fractions in the scale raw get/set functions. + */ +static IIO_CONST_ATTR(anglevel_scale_available, + "0.000122070 " + "0.000274658 " + "0.000518798 " + "0.001068115"); + +static struct attribute *mpu3050_attributes[] = { + &iio_const_attr_anglevel_scale_available.dev_attr.attr, + NULL, +}; + +static const struct attribute_group mpu3050_attribute_group = { + .attrs = mpu3050_attributes, +}; + +static const struct iio_info mpu3050_info = { + .driver_module = THIS_MODULE, + .read_raw = mpu3050_read_raw, + .write_raw = mpu3050_write_raw, + .attrs = &mpu3050_attribute_group, + .driver_module = THIS_MODULE, +}; + +/** + * mpu3050_read_mem() - read MPU-3050 internal memory + * @mpu3050: device to read from + * @bank: target bank + * @addr: target address + * @len: number of bytes + * @buf: the buffer to store the read bytes in + */ +static int mpu3050_read_mem(struct mpu3050 *mpu3050, + u8 bank, + u8 addr, + u8 len, + u8 *buf) +{ + int ret; + + ret = regmap_write(mpu3050->map, + MPU3050_BANK_SEL, + bank); + if (ret) + return ret; + + ret = regmap_write(mpu3050->map, + MPU3050_MEM_START_ADDR, + addr); + if (ret) + return ret; + + return regmap_bulk_read(mpu3050->map, + MPU3050_MEM_R_W, + buf, + len); +} + +static int mpu3050_hw_init(struct mpu3050 *mpu3050) +{ + int ret; + u8 otp[8]; + + /* Reset */ + ret = regmap_update_bits(mpu3050->map, + MPU3050_PWR_MGM, + MPU3050_PWR_MGM_RESET, + MPU3050_PWR_MGM_RESET); + if (ret) + return ret; + + /* Turn on the PLL */ + ret = regmap_update_bits(mpu3050->map, + MPU3050_PWR_MGM, + MPU3050_PWR_MGM_CLKSEL_MASK, + MPU3050_PWR_MGM_PLL_Z); + if (ret) + return ret; + + /* Disable IRQs */ + ret = regmap_write(mpu3050->map, + MPU3050_INT_CFG, + 0); + if (ret) + return ret; + + /* Read out the 8 bytes of OTP (one-time-programmable) memory */ + ret = mpu3050_read_mem(mpu3050, + (MPU3050_MEM_PRFTCH | + MPU3050_MEM_USER_BANK | + MPU3050_MEM_OTP_BANK_0), + 0, + sizeof(otp), + otp); + if (ret) + return ret; + + /* This is device-unique data so it goes into the entropy pool */ + add_device_randomness(otp, sizeof(otp)); + + dev_info(mpu3050->dev, + "die ID: %04X, wafer ID: %02X, A lot ID: %04X, " + "W lot ID: %03X, WP ID: %01X, rev ID: %02X\n", + /* Die ID, bits 0-12 */ + (otp[1] << 8 | otp[0]) & 0x1fff, + /* Wafer ID, bits 13-17 */ + ((otp[2] << 8 | otp[1]) & 0x03e0) >> 5, + /* A lot ID, bits 18-33 */ + ((otp[4] << 16 | otp[3] << 8 | otp[2]) & 0x3fffc) >> 2, + /* W lot ID, bits 34-45 */ + ((otp[5] << 8 | otp[4]) & 0x3ffc) >> 2, + /* WP ID, bits 47-49 */ + ((otp[6] << 8 | otp[5]) & 0x0380) >> 7, + /* rev ID, bits 50-55 */ + otp[6] >> 2); + + return 0; +} + +static int mpu3050_power_up(struct mpu3050 *mpu3050) +{ + int ret; + + ret = regulator_bulk_enable(ARRAY_SIZE(mpu3050->regs), mpu3050->regs); + if (ret) { + dev_err(mpu3050->dev, "cannot enable regulators\n"); + return ret; + } + /* + * 20-100 ms start-up time for register read/write according to + * the datasheet, be on the safe side and wait 200 ms. + */ + msleep(200); + + /* Take device out of sleep mode */ + ret = regmap_update_bits(mpu3050->map, MPU3050_PWR_MGM, + MPU3050_PWR_MGM_SLEEP, 0); + if (ret) { + dev_err(mpu3050->dev, "error setting power mode\n"); + return ret; + } + msleep(10); + + return 0; +} + +static int mpu3050_power_down(struct mpu3050 *mpu3050) +{ + int ret; + + /* + * Put MPU-3050 into sleep mode before cutting regulators. + * This is important, because we may not be the sole user + * of the regulator so the power may stay on after this, and + * then we would be wasting power unless we go to sleep mode + * first. + */ + ret = regmap_update_bits(mpu3050->map, MPU3050_PWR_MGM, + MPU3050_PWR_MGM_SLEEP, MPU3050_PWR_MGM_SLEEP); + if (ret) + dev_err(mpu3050->dev, "error putting to sleep\n"); + + ret = regulator_bulk_disable(ARRAY_SIZE(mpu3050->regs), mpu3050->regs); + if (ret) + dev_err(mpu3050->dev, "error disabling regulators\n"); + + return 0; +} + +static irqreturn_t mpu3050_irq_handler(int irq, void *p) +{ + struct iio_trigger *trig = p; + struct iio_dev *indio_dev = iio_trigger_get_drvdata(trig); + struct mpu3050 *mpu3050 = iio_priv(indio_dev); + + if (!mpu3050->hw_irq_trigger) + return IRQ_NONE; + + /* Get the time stamp as close in time as possible */ + mpu3050->hw_timestamp = iio_get_time_ns(indio_dev); + + return IRQ_WAKE_THREAD; +} + +static irqreturn_t mpu3050_irq_thread(int irq, void *p) +{ + struct iio_trigger *trig = p; + struct iio_dev *indio_dev = iio_trigger_get_drvdata(trig); + struct mpu3050 *mpu3050 = iio_priv(indio_dev); + unsigned int val; + int ret; + + /* ACK IRQ and check if it was from us */ + ret = regmap_read(mpu3050->map, MPU3050_INT_STATUS, &val); + if (ret) { + dev_err(mpu3050->dev, "error reading IRQ status\n"); + return IRQ_HANDLED; + } + if (!(val & MPU3050_INT_STATUS_RAW_RDY)) + return IRQ_NONE; + + iio_trigger_poll_chained(p); + + return IRQ_HANDLED; +} + +/** + * mpu3050_drdy_trigger_set_state() - set data ready interrupt state + * @trig: trigger instance + * @enable: true if trigger should be enabled, false to disable + */ +static int mpu3050_drdy_trigger_set_state(struct iio_trigger *trig, + bool enable) +{ + struct iio_dev *indio_dev = iio_trigger_get_drvdata(trig); + struct mpu3050 *mpu3050 = iio_priv(indio_dev); + unsigned int val; + int ret; + + /* Disabling trigger: disable interrupt and return */ + if (!enable) { + /* Disable all interrupts */ + ret = regmap_write(mpu3050->map, + MPU3050_INT_CFG, + 0); + if (ret) + dev_err(mpu3050->dev, "error disabling IRQ\n"); + + /* Clear IRQ flag */ + ret = regmap_read(mpu3050->map, MPU3050_INT_STATUS, &val); + if (ret) + dev_err(mpu3050->dev, "error clearing IRQ status\n"); + + /* Disable all things in the FIFO and reset it */ + ret = regmap_write(mpu3050->map, MPU3050_FIFO_EN, 0); + if (ret) + dev_err(mpu3050->dev, "error disabling FIFO\n"); + + ret = regmap_write(mpu3050->map, MPU3050_USR_CTRL, + MPU3050_USR_CTRL_FIFO_RST); + if (ret) + dev_err(mpu3050->dev, "error resetting FIFO\n"); + + pm_runtime_mark_last_busy(mpu3050->dev); + pm_runtime_put_autosuspend(mpu3050->dev); + mpu3050->hw_irq_trigger = false; + + return 0; + } else { + /* Else we're enabling the trigger from this point */ + pm_runtime_get_sync(mpu3050->dev); + mpu3050->hw_irq_trigger = true; + + /* Disable all things in the FIFO */ + ret = regmap_write(mpu3050->map, MPU3050_FIFO_EN, 0); + if (ret) + return ret; + + /* Reset and enable the FIFO */ + ret = regmap_update_bits(mpu3050->map, MPU3050_USR_CTRL, + MPU3050_USR_CTRL_FIFO_EN | + MPU3050_USR_CTRL_FIFO_RST, + MPU3050_USR_CTRL_FIFO_EN | + MPU3050_USR_CTRL_FIFO_RST); + if (ret) + return ret; + + mpu3050->pending_fifo_footer = false; + + /* Turn on the FIFO for temp+X+Y+Z */ + ret = regmap_write(mpu3050->map, MPU3050_FIFO_EN, + MPU3050_FIFO_EN_TEMP_OUT | + MPU3050_FIFO_EN_GYRO_XOUT | + MPU3050_FIFO_EN_GYRO_YOUT | + MPU3050_FIFO_EN_GYRO_ZOUT | + MPU3050_FIFO_EN_FOOTER); + if (ret) + return ret; + + /* Configure the sample engine */ + ret = mpu3050_start_sampling(mpu3050); + if (ret) + return ret; + + /* Clear IRQ flag */ + ret = regmap_read(mpu3050->map, MPU3050_INT_STATUS, &val); + if (ret) + dev_err(mpu3050->dev, "error clearing IRQ status\n"); + + /* Give us interrupts whenever there is new data ready */ + val = MPU3050_INT_RAW_RDY_EN; + + if (mpu3050->irq_actl) + val |= MPU3050_INT_ACTL; + if (mpu3050->irq_latch) + val |= MPU3050_INT_LATCH_EN; + if (mpu3050->irq_opendrain) + val |= MPU3050_INT_OPEN; + + ret = regmap_write(mpu3050->map, MPU3050_INT_CFG, val); + if (ret) + return ret; + } + + return 0; +} + +static const struct iio_trigger_ops mpu3050_trigger_ops = { + .owner = THIS_MODULE, + .set_trigger_state = mpu3050_drdy_trigger_set_state, +}; + +static int mpu3050_trigger_probe(struct iio_dev *indio_dev, int irq) +{ + struct mpu3050 *mpu3050 = iio_priv(indio_dev); + unsigned long irq_trig; + int ret; + + mpu3050->trig = devm_iio_trigger_alloc(&indio_dev->dev, + "%s-dev%d", + indio_dev->name, + indio_dev->id); + if (!mpu3050->trig) + return -ENOMEM; + + /* Check if IRQ is open drain */ + if (of_property_read_bool(mpu3050->dev->of_node, "drive-open-drain")) + mpu3050->irq_opendrain = true; + + irq_trig = irqd_get_trigger_type(irq_get_irq_data(irq)); + /* + * Configure the interrupt generator hardware to supply whatever + * the interrupt is configured for, edges low/high level low/high, + * we can provide it all. + */ + switch (irq_trig) { + case IRQF_TRIGGER_RISING: + dev_info(&indio_dev->dev, + "pulse interrupts on the rising edge\n"); + if (mpu3050->irq_opendrain) { + dev_info(&indio_dev->dev, + "rising edge incompatible with open drain\n"); + mpu3050->irq_opendrain = false; + } + break; + case IRQF_TRIGGER_FALLING: + mpu3050->irq_actl = true; + dev_info(&indio_dev->dev, + "pulse interrupts on the falling edge\n"); + break; + case IRQF_TRIGGER_HIGH: + mpu3050->irq_latch = true; + dev_info(&indio_dev->dev, + "interrupts active high level\n"); + if (mpu3050->irq_opendrain) { + dev_info(&indio_dev->dev, + "active high incompatible with open drain\n"); + mpu3050->irq_opendrain = false; + } + /* + * With level IRQs, we mask the IRQ until it is processed, + * but with edge IRQs (pulses) we can queue several interrupts + * in the top half. + */ + irq_trig |= IRQF_ONESHOT; + break; + case IRQF_TRIGGER_LOW: + mpu3050->irq_latch = true; + mpu3050->irq_actl = true; + irq_trig |= IRQF_ONESHOT; + dev_info(&indio_dev->dev, + "interrupts active low level\n"); + break; + default: + /* This is the most preferred mode, if possible */ + dev_err(&indio_dev->dev, + "unsupported IRQ trigger specified (%lx), enforce " + "rising edge\n", irq_trig); + irq_trig = IRQF_TRIGGER_RISING; + break; + } + + /* An open drain line can be shared with several devices */ + if (mpu3050->irq_opendrain) + irq_trig |= IRQF_SHARED; + + ret = request_threaded_irq(irq, + mpu3050_irq_handler, + mpu3050_irq_thread, + irq_trig, + mpu3050->trig->name, + mpu3050->trig); + if (ret) { + dev_err(mpu3050->dev, + "can't get IRQ %d, error %d\n", irq, ret); + return ret; + } + + mpu3050->irq = irq; + mpu3050->trig->dev.parent = mpu3050->dev; + mpu3050->trig->ops = &mpu3050_trigger_ops; + iio_trigger_set_drvdata(mpu3050->trig, indio_dev); + + ret = iio_trigger_register(mpu3050->trig); + if (ret) + return ret; + + indio_dev->trig = iio_trigger_get(mpu3050->trig); + + return 0; +} + +int mpu3050_common_probe(struct device *dev, + struct regmap *map, + int irq, + const char *name) +{ + struct iio_dev *indio_dev; + struct mpu3050 *mpu3050; + unsigned int val; + int ret; + + indio_dev = devm_iio_device_alloc(dev, sizeof(*mpu3050)); + if (!indio_dev) + return -ENOMEM; + mpu3050 = iio_priv(indio_dev); + + mpu3050->dev = dev; + mpu3050->map = map; + mutex_init(&mpu3050->lock); + /* Default fullscale: 2000 degrees per second */ + mpu3050->fullscale = FS_2000_DPS; + /* 1 kHz, divide by 100, default frequency = 10 Hz */ + mpu3050->lpf = MPU3050_DLPF_CFG_188HZ; + mpu3050->divisor = 99; + + /* Read the mounting matrix, if present */ + ret = of_iio_read_mount_matrix(dev, "mount-matrix", + &mpu3050->orientation); + if (ret) + return ret; + + /* Fetch and turn on regulators */ + mpu3050->regs[0].supply = mpu3050_reg_vdd; + mpu3050->regs[1].supply = mpu3050_reg_vlogic; + ret = devm_regulator_bulk_get(dev, ARRAY_SIZE(mpu3050->regs), + mpu3050->regs); + if (ret) { + dev_err(dev, "Cannot get regulators\n"); + return ret; + } + + ret = mpu3050_power_up(mpu3050); + if (ret) + return ret; + + ret = regmap_read(map, MPU3050_CHIP_ID_REG, &val); + if (ret) { + dev_err(dev, "could not read device ID\n"); + ret = -ENODEV; + + goto err_power_down; + } + + if (val != MPU3050_CHIP_ID) { + dev_err(dev, "unsupported chip id %02x\n", (u8)val); + ret = -ENODEV; + goto err_power_down; + } + + ret = regmap_read(map, MPU3050_PRODUCT_ID_REG, &val); + if (ret) { + dev_err(dev, "could not read device ID\n"); + ret = -ENODEV; + + goto err_power_down; + } + dev_info(dev, "found MPU-3050 part no: %d, version: %d\n", + ((val >> 4) & 0xf), (val & 0xf)); + + ret = mpu3050_hw_init(mpu3050); + if (ret) + goto err_power_down; + + indio_dev->dev.parent = dev; + indio_dev->channels = mpu3050_channels; + indio_dev->num_channels = ARRAY_SIZE(mpu3050_channels); + indio_dev->info = &mpu3050_info; + indio_dev->available_scan_masks = mpu3050_scan_masks; + indio_dev->modes = INDIO_DIRECT_MODE; + indio_dev->name = name; + + ret = iio_triggered_buffer_setup(indio_dev, iio_pollfunc_store_time, + mpu3050_trigger_handler, + &mpu3050_buffer_setup_ops); + if (ret) { + dev_err(dev, "triggered buffer setup failed\n"); + goto err_power_down; + } + + ret = iio_device_register(indio_dev); + if (ret) { + dev_err(dev, "device register failed\n"); + goto err_cleanup_buffer; + } + + dev_set_drvdata(dev, indio_dev); + + /* Check if we have an assigned IRQ to use as trigger */ + if (irq) { + ret = mpu3050_trigger_probe(indio_dev, irq); + if (ret) + dev_err(dev, "failed to register trigger\n"); + } + + /* Enable runtime PM */ + pm_runtime_get_noresume(dev); + pm_runtime_set_active(dev); + pm_runtime_enable(dev); + /* + * Set autosuspend to two orders of magnitude larger than the + * start-up time. 100ms start-up time means 10000ms autosuspend, + * i.e. 10 seconds. + */ + pm_runtime_set_autosuspend_delay(dev, 10000); + pm_runtime_use_autosuspend(dev); + pm_runtime_put(dev); + + return 0; + +err_cleanup_buffer: + iio_triggered_buffer_cleanup(indio_dev); +err_power_down: + mpu3050_power_down(mpu3050); + + return ret; +} +EXPORT_SYMBOL(mpu3050_common_probe); + +int mpu3050_common_remove(struct device *dev) +{ + struct iio_dev *indio_dev = dev_get_drvdata(dev); + struct mpu3050 *mpu3050 = iio_priv(indio_dev); + + pm_runtime_get_sync(dev); + pm_runtime_put_noidle(dev); + pm_runtime_disable(dev); + iio_triggered_buffer_cleanup(indio_dev); + if (mpu3050->irq) + free_irq(mpu3050->irq, mpu3050); + iio_device_unregister(indio_dev); + mpu3050_power_down(mpu3050); + + return 0; +} +EXPORT_SYMBOL(mpu3050_common_remove); + +#ifdef CONFIG_PM +static int mpu3050_runtime_suspend(struct device *dev) +{ + return mpu3050_power_down(iio_priv(dev_get_drvdata(dev))); +} + +static int mpu3050_runtime_resume(struct device *dev) +{ + return mpu3050_power_up(iio_priv(dev_get_drvdata(dev))); +} +#endif /* CONFIG_PM */ + +const struct dev_pm_ops mpu3050_dev_pm_ops = { + SET_SYSTEM_SLEEP_PM_OPS(pm_runtime_force_suspend, + pm_runtime_force_resume) + SET_RUNTIME_PM_OPS(mpu3050_runtime_suspend, + mpu3050_runtime_resume, NULL) +}; +EXPORT_SYMBOL(mpu3050_dev_pm_ops); + +MODULE_AUTHOR("Linus Walleij"); +MODULE_DESCRIPTION("MPU3050 gyroscope driver"); +MODULE_LICENSE("GPL"); diff --git a/drivers/iio/gyro/mpu3050-i2c.c b/drivers/iio/gyro/mpu3050-i2c.c new file mode 100644 index 000000000000..06007200bf49 --- /dev/null +++ b/drivers/iio/gyro/mpu3050-i2c.c @@ -0,0 +1,124 @@ +#include <linux/err.h> +#include <linux/i2c.h> +#include <linux/i2c-mux.h> +#include <linux/iio/iio.h> +#include <linux/module.h> +#include <linux/regmap.h> +#include <linux/pm_runtime.h> + +#include "mpu3050.h" + +static const struct regmap_config mpu3050_i2c_regmap_config = { + .reg_bits = 8, + .val_bits = 8, +}; + +static int mpu3050_i2c_bypass_select(struct i2c_mux_core *mux, u32 chan_id) +{ + struct mpu3050 *mpu3050 = i2c_mux_priv(mux); + + /* Just power up the device, that is all that is needed */ + pm_runtime_get_sync(mpu3050->dev); + return 0; +} + +static int mpu3050_i2c_bypass_deselect(struct i2c_mux_core *mux, u32 chan_id) +{ + struct mpu3050 *mpu3050 = i2c_mux_priv(mux); + + pm_runtime_mark_last_busy(mpu3050->dev); + pm_runtime_put_autosuspend(mpu3050->dev); + return 0; +} + +static int mpu3050_i2c_probe(struct i2c_client *client, + const struct i2c_device_id *id) +{ + struct regmap *regmap; + const char *name; + struct mpu3050 *mpu3050; + int ret; + + if (!i2c_check_functionality(client->adapter, + I2C_FUNC_SMBUS_I2C_BLOCK)) + return -EOPNOTSUPP; + + if (id) + name = id->name; + else + return -ENODEV; + + regmap = devm_regmap_init_i2c(client, &mpu3050_i2c_regmap_config); + if (IS_ERR(regmap)) { + dev_err(&client->dev, "Failed to register i2c regmap %d\n", + (int)PTR_ERR(regmap)); + return PTR_ERR(regmap); + } + + ret = mpu3050_common_probe(&client->dev, regmap, client->irq, name); + if (ret) + return ret; + + /* The main driver is up, now register the I2C mux */ + mpu3050 = iio_priv(dev_get_drvdata(&client->dev)); + mpu3050->i2cmux = i2c_mux_alloc(client->adapter, &client->dev, + 1, 0, I2C_MUX_LOCKED | I2C_MUX_GATE, + mpu3050_i2c_bypass_select, + mpu3050_i2c_bypass_deselect); + /* Just fail the mux, there is no point in killing the driver */ + if (!mpu3050->i2cmux) + dev_err(&client->dev, "failed to allocate I2C mux\n"); + else { + mpu3050->i2cmux->priv = mpu3050; + ret = i2c_mux_add_adapter(mpu3050->i2cmux, 0, 0, 0); + if (ret) + dev_err(&client->dev, "failed to add I2C mux\n"); + } + + return 0; +} + +static int mpu3050_i2c_remove(struct i2c_client *client) +{ + struct iio_dev *indio_dev = dev_get_drvdata(&client->dev); + struct mpu3050 *mpu3050 = iio_priv(indio_dev); + + if (mpu3050->i2cmux) + i2c_mux_del_adapters(mpu3050->i2cmux); + + return mpu3050_common_remove(&client->dev); +} + +/* + * device id table is used to identify what device can be + * supported by this driver + */ +static const struct i2c_device_id mpu3050_i2c_id[] = { + { "mpu3050" }, + {} +}; +MODULE_DEVICE_TABLE(i2c, mpu3050_i2c_id); + +static const struct of_device_id mpu3050_i2c_of_match[] = { + { .compatible = "invensense,mpu3050", .data = "mpu3050" }, + /* Deprecated vendor ID from the Input driver */ + { .compatible = "invn,mpu3050", .data = "mpu3050" }, + { }, +}; +MODULE_DEVICE_TABLE(of, mpu3050_i2c_of_match); + +static struct i2c_driver mpu3050_i2c_driver = { + .probe = mpu3050_i2c_probe, + .remove = mpu3050_i2c_remove, + .id_table = mpu3050_i2c_id, + .driver = { + .of_match_table = mpu3050_i2c_of_match, + .name = "mpu3050-i2c", + .pm = &mpu3050_dev_pm_ops, + }, +}; +module_i2c_driver(mpu3050_i2c_driver); + +MODULE_AUTHOR("Linus Walleij"); +MODULE_DESCRIPTION("Invensense MPU3050 gyroscope driver"); +MODULE_LICENSE("GPL"); diff --git a/drivers/iio/gyro/mpu3050.h b/drivers/iio/gyro/mpu3050.h new file mode 100644 index 000000000000..bef87a714dc5 --- /dev/null +++ b/drivers/iio/gyro/mpu3050.h @@ -0,0 +1,96 @@ +#include <linux/iio/iio.h> +#include <linux/mutex.h> +#include <linux/regmap.h> +#include <linux/regulator/consumer.h> +#include <linux/i2c.h> + +/** + * enum mpu3050_fullscale - indicates the full range of the sensor in deg/sec + */ +enum mpu3050_fullscale { + FS_250_DPS = 0, + FS_500_DPS, + FS_1000_DPS, + FS_2000_DPS, +}; + +/** + * enum mpu3050_lpf - indicates the low pass filter width + */ +enum mpu3050_lpf { + /* This implicity sets sample frequency to 8 kHz */ + LPF_256_HZ_NOLPF = 0, + /* All others sets the sample frequency to 1 kHz */ + LPF_188_HZ, + LPF_98_HZ, + LPF_42_HZ, + LPF_20_HZ, + LPF_10_HZ, + LPF_5_HZ, + LPF_2100_HZ_NOLPF, +}; + +enum mpu3050_axis { + AXIS_X = 0, + AXIS_Y, + AXIS_Z, + AXIS_MAX, +}; + +/** + * struct mpu3050 - instance state container for the device + * @dev: parent device for this instance + * @orientation: mounting matrix, flipped axis etc + * @map: regmap to reach the registers + * @lock: serialization lock to marshal all requests + * @irq: the IRQ used for this device + * @regs: the regulators to power this device + * @fullscale: the current fullscale setting for the device + * @lpf: digital low pass filter setting for the device + * @divisor: base frequency divider: divides 8 or 1 kHz + * @calibration: the three signed 16-bit calibration settings that + * get written into the offset registers for each axis to compensate + * for DC offsets + * @trig: trigger for the MPU-3050 interrupt, if present + * @hw_irq_trigger: hardware interrupt trigger is in use + * @irq_actl: interrupt is active low + * @irq_latch: latched IRQ, this means that it is a level IRQ + * @irq_opendrain: the interrupt line shall be configured open drain + * @pending_fifo_footer: tells us if there is a pending footer in the FIFO + * that we have to read out first when handling the FIFO + * @hw_timestamp: latest hardware timestamp from the trigger IRQ, when in + * use + * @i2cmux: an I2C mux reflecting the fact that this sensor is a hub with + * a pass-through I2C interface coming out of it: this device needs to be + * powered up in order to reach devices on the other side of this mux + */ +struct mpu3050 { + struct device *dev; + struct iio_mount_matrix orientation; + struct regmap *map; + struct mutex lock; + int irq; + struct regulator_bulk_data regs[2]; + enum mpu3050_fullscale fullscale; + enum mpu3050_lpf lpf; + u8 divisor; + s16 calibration[3]; + struct iio_trigger *trig; + bool hw_irq_trigger; + bool irq_actl; + bool irq_latch; + bool irq_opendrain; + bool pending_fifo_footer; + s64 hw_timestamp; + struct i2c_mux_core *i2cmux; +}; + +/* Probe called from different transports */ +int mpu3050_common_probe(struct device *dev, + struct regmap *map, + int irq, + const char *name); +int mpu3050_common_remove(struct device *dev); + +/* PM ops */ +extern const struct dev_pm_ops mpu3050_dev_pm_ops; diff --git a/drivers/iio/humidity/hts221_buffer.c b/drivers/iio/humidity/hts221_buffer.c index 76b2e8130b6f..72ddcdac21a2 100644 --- a/drivers/iio/humidity/hts221_buffer.c +++ b/drivers/iio/humidity/hts221_buffer.c @@ -15,7 +15,6 @@ #include <linux/iio/iio.h> #include <linux/iio/trigger.h> -#include <linux/interrupt.h> #include <linux/iio/events.h> #include <linux/iio/trigger_consumer.h> #include <linux/iio/triggered_buffer.h> diff --git a/drivers/iio/humidity/si7020.c b/drivers/iio/humidity/si7020.c index ffc2ccf6374e..345a7656c5ef 100644 --- a/drivers/iio/humidity/si7020.c +++ b/drivers/iio/humidity/si7020.c @@ -154,8 +154,17 @@ static const struct i2c_device_id si7020_id[] = { }; MODULE_DEVICE_TABLE(i2c, si7020_id); +static const struct of_device_id si7020_dt_ids[] = { + { .compatible = "silabs,si7020" }, + { } +}; +MODULE_DEVICE_TABLE(of, si7020_dt_ids); + static struct i2c_driver si7020_driver = { - .driver.name = "si7020", + .driver = { + .name = "si7020", + .of_match_table = of_match_ptr(si7020_dt_ids), + }, .probe = si7020_probe, .id_table = si7020_id, }; diff --git a/drivers/iio/temperature/maxim_thermocouple.c b/drivers/iio/temperature/maxim_thermocouple.c index 066161a4bccd..f962f31a5eb2 100644 --- a/drivers/iio/temperature/maxim_thermocouple.c +++ b/drivers/iio/temperature/maxim_thermocouple.c @@ -136,6 +136,8 @@ static int maxim_thermocouple_read(struct maxim_thermocouple_data *data, ret = spi_read(data->spi, (void *)&buf32, storage_bytes); *val = be32_to_cpu(buf32); break; + default: + ret = -EINVAL; } if (ret) diff --git a/drivers/mfd/ti_am335x_tscadc.c b/drivers/mfd/ti_am335x_tscadc.c index c8f027b4ea4c..0f3fab47fe48 100644 --- a/drivers/mfd/ti_am335x_tscadc.c +++ b/drivers/mfd/ti_am335x_tscadc.c @@ -183,6 +183,7 @@ static int ti_tscadc_probe(struct platform_device *pdev) tscadc->irq = err; res = platform_get_resource(pdev, IORESOURCE_MEM, 0); + tscadc->tscadc_phys_base = res->start; tscadc->tscadc_base = devm_ioremap_resource(&pdev->dev, res); if (IS_ERR(tscadc->tscadc_base)) return PTR_ERR(tscadc->tscadc_base); diff --git a/drivers/platform/chrome/cros_ec_dev.c b/drivers/platform/chrome/cros_ec_dev.c index 8abd80dbcbed..47268ecedc4d 100644 --- a/drivers/platform/chrome/cros_ec_dev.c +++ b/drivers/platform/chrome/cros_ec_dev.c @@ -18,6 +18,7 @@ */ #include <linux/fs.h> +#include <linux/mfd/core.h> #include <linux/module.h> #include <linux/platform_device.h> #include <linux/slab.h> @@ -87,6 +88,41 @@ exit: return ret; } +static int cros_ec_check_features(struct cros_ec_dev *ec, int feature) +{ + struct cros_ec_command *msg; + int ret; + + if (ec->features[0] == -1U && ec->features[1] == -1U) { + /* features bitmap not read yet */ + + msg = kmalloc(sizeof(*msg) + sizeof(ec->features), GFP_KERNEL); + if (!msg) + return -ENOMEM; + + msg->version = 0; + msg->command = EC_CMD_GET_FEATURES + ec->cmd_offset; + msg->insize = sizeof(ec->features); + msg->outsize = 0; + + ret = cros_ec_cmd_xfer(ec->ec_dev, msg); + if (ret < 0 || msg->result != EC_RES_SUCCESS) { + dev_warn(ec->dev, "cannot get EC features: %d/%d\n", + ret, msg->result); + memset(ec->features, 0, sizeof(ec->features)); + } + + memcpy(ec->features, msg->data, sizeof(ec->features)); + + dev_dbg(ec->dev, "EC features %08x %08x\n", + ec->features[0], ec->features[1]); + + kfree(msg); + } + + return ec->features[feature / 32] & EC_FEATURE_MASK_0(feature); +} + /* Device file ops */ static int ec_device_open(struct inode *inode, struct file *filp) { @@ -230,6 +266,123 @@ static void __remove(struct device *dev) kfree(ec); } +static void cros_ec_sensors_register(struct cros_ec_dev *ec) +{ + /* + * Issue a command to get the number of sensor reported. + * Build an array of sensors driver and register them all. + */ + int ret, i, id, sensor_num; + struct mfd_cell *sensor_cells; + struct cros_ec_sensor_platform *sensor_platforms; + int sensor_type[MOTIONSENSE_TYPE_MAX]; + struct ec_params_motion_sense *params; + struct ec_response_motion_sense *resp; + struct cros_ec_command *msg; + + msg = kzalloc(sizeof(struct cros_ec_command) + + max(sizeof(*params), sizeof(*resp)), GFP_KERNEL); + if (msg == NULL) + return; + + msg->version = 2; + msg->command = EC_CMD_MOTION_SENSE_CMD + ec->cmd_offset; + msg->outsize = sizeof(*params); + msg->insize = sizeof(*resp); + + params = (struct ec_params_motion_sense *)msg->data; + params->cmd = MOTIONSENSE_CMD_DUMP; + + ret = cros_ec_cmd_xfer(ec->ec_dev, msg); + if (ret < 0 || msg->result != EC_RES_SUCCESS) { + dev_warn(ec->dev, "cannot get EC sensor information: %d/%d\n", + ret, msg->result); + goto error; + } + + resp = (struct ec_response_motion_sense *)msg->data; + sensor_num = resp->dump.sensor_count; + /* Allocate 2 extra sensors in case lid angle or FIFO are needed */ + sensor_cells = kzalloc(sizeof(struct mfd_cell) * (sensor_num + 2), + GFP_KERNEL); + if (sensor_cells == NULL) + goto error; + + sensor_platforms = kzalloc(sizeof(struct cros_ec_sensor_platform) * + (sensor_num + 1), GFP_KERNEL); + if (sensor_platforms == NULL) + goto error_platforms; + + memset(sensor_type, 0, sizeof(sensor_type)); + id = 0; + for (i = 0; i < sensor_num; i++) { + params->cmd = MOTIONSENSE_CMD_INFO; + params->info.sensor_num = i; + ret = cros_ec_cmd_xfer(ec->ec_dev, msg); + if (ret < 0 || msg->result != EC_RES_SUCCESS) { + dev_warn(ec->dev, "no info for EC sensor %d : %d/%d\n", + i, ret, msg->result); + continue; + } + switch (resp->info.type) { + case MOTIONSENSE_TYPE_ACCEL: + sensor_cells[id].name = "cros-ec-accel"; + break; + case MOTIONSENSE_TYPE_GYRO: + sensor_cells[id].name = "cros-ec-gyro"; + break; + case MOTIONSENSE_TYPE_MAG: + sensor_cells[id].name = "cros-ec-mag"; + break; + case MOTIONSENSE_TYPE_PROX: + sensor_cells[id].name = "cros-ec-prox"; + break; + case MOTIONSENSE_TYPE_LIGHT: + sensor_cells[id].name = "cros-ec-light"; + break; + case MOTIONSENSE_TYPE_ACTIVITY: + sensor_cells[id].name = "cros-ec-activity"; + break; + default: + dev_warn(ec->dev, "unknown type %d\n", resp->info.type); + continue; + } + sensor_platforms[id].sensor_num = i; + sensor_cells[id].id = sensor_type[resp->info.type]; + sensor_cells[id].platform_data = &sensor_platforms[id]; + sensor_cells[id].pdata_size = + sizeof(struct cros_ec_sensor_platform); + + sensor_type[resp->info.type]++; + id++; + } + if (sensor_type[MOTIONSENSE_TYPE_ACCEL] >= 2) { + sensor_platforms[id].sensor_num = sensor_num; + + sensor_cells[id].name = "cros-ec-angle"; + sensor_cells[id].id = 0; + sensor_cells[id].platform_data = &sensor_platforms[id]; + sensor_cells[id].pdata_size = + sizeof(struct cros_ec_sensor_platform); + id++; + } + if (cros_ec_check_features(ec, EC_FEATURE_MOTION_SENSE_FIFO)) { + sensor_cells[id].name = "cros-ec-ring"; + id++; + } + + ret = mfd_add_devices(ec->dev, 0, sensor_cells, id, + NULL, 0, NULL); + if (ret) + dev_err(ec->dev, "failed to add EC sensors\n"); + + kfree(sensor_platforms); +error_platforms: + kfree(sensor_cells); +error: + kfree(msg); +} + static int ec_device_probe(struct platform_device *pdev) { int retval = -ENOMEM; @@ -245,6 +398,8 @@ static int ec_device_probe(struct platform_device *pdev) ec->ec_dev = dev_get_drvdata(dev->parent); ec->dev = dev; ec->cmd_offset = ec_platform->cmd_offset; + ec->features[0] = -1U; /* Not cached yet */ + ec->features[1] = -1U; /* Not cached yet */ device_initialize(&ec->class_dev); cdev_init(&ec->cdev, &fops); @@ -282,6 +437,10 @@ static int ec_device_probe(struct platform_device *pdev) goto dev_reg_failed; } + /* check whether this EC is a sensor hub. */ + if (cros_ec_check_features(ec, EC_FEATURE_MOTION_SENSE)) + cros_ec_sensors_register(ec); + return 0; dev_reg_failed: diff --git a/drivers/staging/iio/adc/ad7192.c b/drivers/staging/iio/adc/ad7192.c index bfa12ceb1e1f..1fb68c01abd5 100644 --- a/drivers/staging/iio/adc/ad7192.c +++ b/drivers/staging/iio/adc/ad7192.c @@ -152,7 +152,8 @@ */ struct ad7192_state { - struct regulator *reg; + struct regulator *avdd; + struct regulator *dvdd; u16 int_vref_mv; u32 mclk; u32 f_order; @@ -633,15 +634,30 @@ static int ad7192_probe(struct spi_device *spi) st = iio_priv(indio_dev); - st->reg = devm_regulator_get(&spi->dev, "vcc"); - if (!IS_ERR(st->reg)) { - ret = regulator_enable(st->reg); - if (ret) - return ret; + st->avdd = devm_regulator_get(&spi->dev, "avdd"); + if (IS_ERR(st->avdd)) + return PTR_ERR(st->avdd); - voltage_uv = regulator_get_voltage(st->reg); + ret = regulator_enable(st->avdd); + if (ret) { + dev_err(&spi->dev, "Failed to enable specified AVdd supply\n"); + return ret; + } + + st->dvdd = devm_regulator_get(&spi->dev, "dvdd"); + if (IS_ERR(st->dvdd)) { + ret = PTR_ERR(st->dvdd); + goto error_disable_avdd; } + ret = regulator_enable(st->dvdd); + if (ret) { + dev_err(&spi->dev, "Failed to enable specified DVdd supply\n"); + goto error_disable_avdd; + } + + voltage_uv = regulator_get_voltage(st->avdd); + if (pdata->vref_mv) st->int_vref_mv = pdata->vref_mv; else if (voltage_uv) @@ -675,7 +691,7 @@ static int ad7192_probe(struct spi_device *spi) ret = ad_sd_setup_buffer_and_trigger(indio_dev); if (ret) - goto error_disable_reg; + goto error_disable_dvdd; ret = ad7192_setup(st, pdata); if (ret) @@ -688,9 +704,10 @@ static int ad7192_probe(struct spi_device *spi) error_remove_trigger: ad_sd_cleanup_buffer_and_trigger(indio_dev); -error_disable_reg: - if (!IS_ERR(st->reg)) - regulator_disable(st->reg); +error_disable_dvdd: + regulator_disable(st->dvdd); +error_disable_avdd: + regulator_disable(st->avdd); return ret; } @@ -703,8 +720,8 @@ static int ad7192_remove(struct spi_device *spi) iio_device_unregister(indio_dev); ad_sd_cleanup_buffer_and_trigger(indio_dev); - if (!IS_ERR(st->reg)) - regulator_disable(st->reg); + regulator_disable(st->dvdd); + regulator_disable(st->avdd); return 0; } diff --git a/drivers/staging/iio/adc/ad7780.c b/drivers/staging/iio/adc/ad7780.c index c9a0c2aa602f..e14960038d3e 100644 --- a/drivers/staging/iio/adc/ad7780.c +++ b/drivers/staging/iio/adc/ad7780.c @@ -173,14 +173,16 @@ static int ad7780_probe(struct spi_device *spi) ad_sd_init(&st->sd, indio_dev, spi, &ad7780_sigma_delta_info); - st->reg = devm_regulator_get(&spi->dev, "vcc"); - if (!IS_ERR(st->reg)) { - ret = regulator_enable(st->reg); - if (ret) - return ret; - - voltage_uv = regulator_get_voltage(st->reg); + st->reg = devm_regulator_get(&spi->dev, "avdd"); + if (IS_ERR(st->reg)) + return PTR_ERR(st->reg); + + ret = regulator_enable(st->reg); + if (ret) { + dev_err(&spi->dev, "Failed to enable specified AVdd supply\n"); + return ret; } + voltage_uv = regulator_get_voltage(st->reg); st->chip_info = &ad7780_chip_info_tbl[spi_get_device_id(spi)->driver_data]; @@ -222,8 +224,7 @@ static int ad7780_probe(struct spi_device *spi) error_cleanup_buffer_and_trigger: ad_sd_cleanup_buffer_and_trigger(indio_dev); error_disable_reg: - if (!IS_ERR(st->reg)) - regulator_disable(st->reg); + regulator_disable(st->reg); return ret; } @@ -236,8 +237,7 @@ static int ad7780_remove(struct spi_device *spi) iio_device_unregister(indio_dev); ad_sd_cleanup_buffer_and_trigger(indio_dev); - if (!IS_ERR(st->reg)) - regulator_disable(st->reg); + regulator_disable(st->reg); return 0; } diff --git a/drivers/staging/iio/cdc/ad7746.c b/drivers/staging/iio/cdc/ad7746.c index f41251ceeacd..81f8b9ee1120 100644 --- a/drivers/staging/iio/cdc/ad7746.c +++ b/drivers/staging/iio/cdc/ad7746.c @@ -70,8 +70,10 @@ #define AD7746_EXCSETUP_EXCLVL(x) (((x) & 0x3) << 0) /* Config Register Bit Designations (AD7746_REG_CFG) */ -#define AD7746_CONF_VTFS(x) ((x) << 6) -#define AD7746_CONF_CAPFS(x) ((x) << 3) +#define AD7746_CONF_VTFS_SHIFT 6 +#define AD7746_CONF_CAPFS_SHIFT 3 +#define AD7746_CONF_VTFS_MASK GENMASK(7, 6) +#define AD7746_CONF_CAPFS_MASK GENMASK(5, 3) #define AD7746_CONF_MODE_IDLE (0 << 0) #define AD7746_CONF_MODE_CONT_CONV (1 << 0) #define AD7746_CONF_MODE_SINGLE_CONV (2 << 0) @@ -217,15 +219,16 @@ static int ad7746_select_channel(struct iio_dev *indio_dev, struct iio_chan_spec const *chan) { struct ad7746_chip_info *chip = iio_priv(indio_dev); - int ret, delay; + int ret, delay, idx; u8 vt_setup, cap_setup; switch (chan->type) { case IIO_CAPACITANCE: cap_setup = (chan->address & 0xFF) | AD7746_CAPSETUP_CAPEN; vt_setup = chip->vt_setup & ~AD7746_VTSETUP_VTEN; - delay = ad7746_cap_filter_rate_table[(chip->config >> 3) & - 0x7][1]; + idx = (chip->config & AD7746_CONF_CAPFS_MASK) >> + AD7746_CONF_CAPFS_SHIFT; + delay = ad7746_cap_filter_rate_table[idx][1]; if (chip->capdac_set != chan->channel) { ret = i2c_smbus_write_byte_data(chip->client, @@ -246,8 +249,9 @@ static int ad7746_select_channel(struct iio_dev *indio_dev, case IIO_TEMP: vt_setup = (chan->address & 0xFF) | AD7746_VTSETUP_VTEN; cap_setup = chip->cap_setup & ~AD7746_CAPSETUP_CAPEN; - delay = ad7746_cap_filter_rate_table[(chip->config >> 6) & - 0x3][1]; + idx = (chip->config & AD7746_CONF_VTFS_MASK) >> + AD7746_CONF_VTFS_SHIFT; + delay = ad7746_cap_filter_rate_table[idx][1]; break; default: return -EINVAL; @@ -369,8 +373,8 @@ static int ad7746_store_cap_filter_rate_setup(struct ad7746_chip_info *chip, if (i >= ARRAY_SIZE(ad7746_cap_filter_rate_table)) i = ARRAY_SIZE(ad7746_cap_filter_rate_table) - 1; - chip->config &= ~AD7746_CONF_CAPFS(0x7); - chip->config |= AD7746_CONF_CAPFS(i); + chip->config &= ~AD7746_CONF_CAPFS_MASK; + chip->config |= i << AD7746_CONF_CAPFS_SHIFT; return 0; } @@ -387,8 +391,8 @@ static int ad7746_store_vt_filter_rate_setup(struct ad7746_chip_info *chip, if (i >= ARRAY_SIZE(ad7746_vt_filter_rate_table)) i = ARRAY_SIZE(ad7746_vt_filter_rate_table) - 1; - chip->config &= ~AD7746_CONF_VTFS(0x3); - chip->config |= AD7746_CONF_VTFS(i); + chip->config &= ~AD7746_CONF_VTFS_MASK; + chip->config |= i << AD7746_CONF_VTFS_SHIFT; return 0; } @@ -527,7 +531,7 @@ static int ad7746_read_raw(struct iio_dev *indio_dev, long mask) { struct ad7746_chip_info *chip = iio_priv(indio_dev); - int ret, delay; + int ret, delay, idx; u8 regval, reg; mutex_lock(&indio_dev->mlock); @@ -635,13 +639,16 @@ static int ad7746_read_raw(struct iio_dev *indio_dev, case IIO_CHAN_INFO_SAMP_FREQ: switch (chan->type) { case IIO_CAPACITANCE: - *val = ad7746_cap_filter_rate_table[ - (chip->config >> 3) & 0x7][0]; + idx = (chip->config & AD7746_CONF_CAPFS_MASK) >> + AD7746_CONF_CAPFS_SHIFT; + *val = ad7746_cap_filter_rate_table[idx][0]; ret = IIO_VAL_INT; break; case IIO_VOLTAGE: - *val = ad7746_vt_filter_rate_table[ - (chip->config >> 6) & 0x3][0]; + idx = (chip->config & AD7746_CONF_VTFS_MASK) >> + AD7746_CONF_VTFS_SHIFT; + *val = ad7746_vt_filter_rate_table[idx][0]; + ret = IIO_VAL_INT; break; default: ret = -EINVAL; diff --git a/drivers/staging/iio/frequency/ad9832.c b/drivers/staging/iio/frequency/ad9832.c index 358400b22d33..639047fade30 100644 --- a/drivers/staging/iio/frequency/ad9832.c +++ b/drivers/staging/iio/frequency/ad9832.c @@ -204,7 +204,6 @@ static int ad9832_probe(struct spi_device *spi) struct ad9832_platform_data *pdata = dev_get_platdata(&spi->dev); struct iio_dev *indio_dev; struct ad9832_state *st; - struct regulator *reg; int ret; if (!pdata) { @@ -212,21 +211,35 @@ static int ad9832_probe(struct spi_device *spi) return -ENODEV; } - reg = devm_regulator_get(&spi->dev, "vcc"); - if (!IS_ERR(reg)) { - ret = regulator_enable(reg); - if (ret) - return ret; + st->avdd = devm_regulator_get(&spi->dev, "avdd"); + if (IS_ERR(st->avdd)) + return PTR_ERR(st->avdd); + + ret = regulator_enable(st->avdd); + if (ret) { + dev_err(&spi->dev, "Failed to enable specified AVDD supply\n"); + return ret; + } + + st->dvdd = devm_regulator_get(&spi->dev, "dvdd"); + if (IS_ERR(st->dvdd)) { + ret = PTR_ERR(st->dvdd); + goto error_disable_avdd; + } + + ret = regulator_enable(st->dvdd); + if (ret) { + dev_err(&spi->dev, "Failed to enable specified DVDD supply\n"); + goto error_disable_avdd; } indio_dev = devm_iio_device_alloc(&spi->dev, sizeof(*st)); if (!indio_dev) { ret = -ENOMEM; - goto error_disable_reg; + goto error_disable_dvdd; } spi_set_drvdata(spi, indio_dev); st = iio_priv(indio_dev); - st->reg = reg; st->mclk = pdata->mclk; st->spi = spi; @@ -277,42 +290,43 @@ static int ad9832_probe(struct spi_device *spi) ret = spi_sync(st->spi, &st->msg); if (ret) { dev_err(&spi->dev, "device init failed\n"); - goto error_disable_reg; + goto error_disable_dvdd; } ret = ad9832_write_frequency(st, AD9832_FREQ0HM, pdata->freq0); if (ret) - goto error_disable_reg; + goto error_disable_dvdd; ret = ad9832_write_frequency(st, AD9832_FREQ1HM, pdata->freq1); if (ret) - goto error_disable_reg; + goto error_disable_dvdd; ret = ad9832_write_phase(st, AD9832_PHASE0H, pdata->phase0); if (ret) - goto error_disable_reg; + goto error_disable_dvdd; ret = ad9832_write_phase(st, AD9832_PHASE1H, pdata->phase1); if (ret) - goto error_disable_reg; + goto error_disable_dvdd; ret = ad9832_write_phase(st, AD9832_PHASE2H, pdata->phase2); if (ret) - goto error_disable_reg; + goto error_disable_dvdd; ret = ad9832_write_phase(st, AD9832_PHASE3H, pdata->phase3); if (ret) - goto error_disable_reg; + goto error_disable_dvdd; ret = iio_device_register(indio_dev); if (ret) - goto error_disable_reg; + goto error_disable_dvdd; return 0; -error_disable_reg: - if (!IS_ERR(reg)) - regulator_disable(reg); +error_disable_dvdd: + regulator_disable(st->dvdd); +error_disable_avdd: + regulator_disable(st->avdd); return ret; } @@ -323,8 +337,8 @@ static int ad9832_remove(struct spi_device *spi) struct ad9832_state *st = iio_priv(indio_dev); iio_device_unregister(indio_dev); - if (!IS_ERR(st->reg)) - regulator_disable(st->reg); + regulator_disable(st->dvdd); + regulator_disable(st->avdd); return 0; } diff --git a/drivers/staging/iio/frequency/ad9832.h b/drivers/staging/iio/frequency/ad9832.h index d32323b46be6..1b08b04482a4 100644 --- a/drivers/staging/iio/frequency/ad9832.h +++ b/drivers/staging/iio/frequency/ad9832.h @@ -58,7 +58,8 @@ /** * struct ad9832_state - driver instance specific data * @spi: spi_device - * @reg: supply regulator + * @avdd: supply regulator for the analog section + * @dvdd: supply regulator for the digital section * @mclk: external master clock * @ctrl_fp: cached frequency/phase control word * @ctrl_ss: cached sync/selsrc control word @@ -76,7 +77,8 @@ struct ad9832_state { struct spi_device *spi; - struct regulator *reg; + struct regulator *avdd; + struct regulator *dvdd; unsigned long mclk; unsigned short ctrl_fp; unsigned short ctrl_ss; diff --git a/drivers/staging/iio/frequency/ad9834.c b/drivers/staging/iio/frequency/ad9834.c index 6366216e4f37..19216af1dfc9 100644 --- a/drivers/staging/iio/frequency/ad9834.c +++ b/drivers/staging/iio/frequency/ad9834.c @@ -329,11 +329,14 @@ static int ad9834_probe(struct spi_device *spi) return -ENODEV; } - reg = devm_regulator_get(&spi->dev, "vcc"); - if (!IS_ERR(reg)) { - ret = regulator_enable(reg); - if (ret) - return ret; + reg = devm_regulator_get(&spi->dev, "avdd"); + if (IS_ERR(reg)) + return PTR_ERR(reg); + + ret = regulator_enable(reg); + if (ret) { + dev_err(&spi->dev, "Failed to enable specified AVDD supply\n"); + return ret; } indio_dev = devm_iio_device_alloc(&spi->dev, sizeof(*st)); @@ -416,8 +419,7 @@ static int ad9834_probe(struct spi_device *spi) return 0; error_disable_reg: - if (!IS_ERR(reg)) - regulator_disable(reg); + regulator_disable(reg); return ret; } @@ -428,8 +430,7 @@ static int ad9834_remove(struct spi_device *spi) struct ad9834_state *st = iio_priv(indio_dev); iio_device_unregister(indio_dev); - if (!IS_ERR(st->reg)) - regulator_disable(st->reg); + regulator_disable(st->reg); return 0; } diff --git a/drivers/staging/iio/impedance-analyzer/ad5933.c b/drivers/staging/iio/impedance-analyzer/ad5933.c index 3892a7470410..944789843938 100644 --- a/drivers/staging/iio/impedance-analyzer/ad5933.c +++ b/drivers/staging/iio/impedance-analyzer/ad5933.c @@ -726,13 +726,16 @@ static int ad5933_probe(struct i2c_client *client, if (!pdata) pdata = &ad5933_default_pdata; - st->reg = devm_regulator_get(&client->dev, "vcc"); - if (!IS_ERR(st->reg)) { - ret = regulator_enable(st->reg); - if (ret) - return ret; - voltage_uv = regulator_get_voltage(st->reg); + st->reg = devm_regulator_get(&client->dev, "vdd"); + if (IS_ERR(st->reg)) + return PTR_ERR(st->reg); + + ret = regulator_enable(st->reg); + if (ret) { + dev_err(&client->dev, "Failed to enable specified VDD supply\n"); + return ret; } + voltage_uv = regulator_get_voltage(st->reg); if (voltage_uv) st->vref_mv = voltage_uv / 1000; @@ -775,8 +778,7 @@ static int ad5933_probe(struct i2c_client *client, error_unreg_ring: iio_kfifo_free(indio_dev->buffer); error_disable_reg: - if (!IS_ERR(st->reg)) - regulator_disable(st->reg); + regulator_disable(st->reg); return ret; } @@ -788,8 +790,7 @@ static int ad5933_remove(struct i2c_client *client) iio_device_unregister(indio_dev); iio_kfifo_free(indio_dev->buffer); - if (!IS_ERR(st->reg)) - regulator_disable(st->reg); + regulator_disable(st->reg); return 0; } diff --git a/drivers/staging/iio/light/tsl2583.c b/drivers/staging/iio/light/tsl2583.c index 08f1583ee34e..7eab17f4557e 100644 --- a/drivers/staging/iio/light/tsl2583.c +++ b/drivers/staging/iio/light/tsl2583.c @@ -29,8 +29,7 @@ #include <linux/slab.h> #include <linux/module.h> #include <linux/iio/iio.h> - -#define TSL258X_MAX_DEVICE_REGS 32 +#include <linux/iio/sysfs.h> /* Triton register offsets */ #define TSL258X_REG_MAX 8 @@ -65,6 +64,9 @@ /* Lux calculation constants */ #define TSL258X_LUX_CALC_OVER_FLOW 65535 +#define TSL2583_CHIP_ID 0x90 +#define TSL2583_CHIP_ID_MASK 0xf0 + enum { TSL258X_CHIP_UNKNOWN = 0, TSL258X_CHIP_WORKING = 1, @@ -124,14 +126,15 @@ static struct taos_lux taos_device_lux[11] = { struct gainadj { s16 ch0; s16 ch1; + s16 mean; }; /* Index = (0 - 3) Used to validate the gain selection index */ static const struct gainadj gainadj[] = { - { 1, 1 }, - { 8, 8 }, - { 16, 16 }, - { 107, 115 } + { 1, 1, 1 }, + { 8, 8, 8 }, + { 16, 16, 16 }, + { 107, 115, 111 } }; /* @@ -140,42 +143,23 @@ static const struct gainadj gainadj[] = { */ static void taos_defaults(struct tsl2583_chip *chip) { - /* Operational parameters */ + /* + * The integration time must be a multiple of 50ms and within the + * range [50, 600] ms. + */ chip->taos_settings.als_time = 100; - /* must be a multiple of 50mS */ + + /* + * This is an index into the gainadj table. Assume clear glass as the + * default. + */ chip->taos_settings.als_gain = 0; - /* this is actually an index into the gain table */ - /* assume clear glass as default */ - chip->taos_settings.als_gain_trim = 1000; - /* default gain trim to account for aperture effects */ - chip->taos_settings.als_cal_target = 130; - /* Known external ALS reading used for calibration */ -} -/* - * Read a number of bytes starting at register (reg) location. - * Return 0, or i2c_smbus_write_byte ERROR code. - */ -static int -taos_i2c_read(struct i2c_client *client, u8 reg, u8 *val, unsigned int len) -{ - int i, ret; + /* Default gain trim to account for aperture effects */ + chip->taos_settings.als_gain_trim = 1000; - for (i = 0; i < len; i++) { - /* select register to write */ - ret = i2c_smbus_write_byte(client, (TSL258X_CMD_REG | reg)); - if (ret < 0) { - dev_err(&client->dev, - "taos_i2c_read failed to write register %x\n", - reg); - return ret; - } - /* read the data */ - *val = i2c_smbus_read_byte(client); - val++; - reg++; - } - return 0; + /* Known external ALS reading used for calibration */ + chip->taos_settings.als_cal_target = 130; } /* @@ -204,40 +188,37 @@ static int taos_get_lux(struct iio_dev *indio_dev) u32 ch0lux = 0; u32 ch1lux = 0; - if (mutex_trylock(&chip->als_mutex) == 0) { - dev_info(&chip->client->dev, "taos_get_lux device is busy\n"); - return chip->als_cur_info.lux; /* busy, so return LAST VALUE */ - } - if (chip->taos_chip_status != TSL258X_CHIP_WORKING) { /* device is not enabled */ dev_err(&chip->client->dev, "taos_get_lux device is not enabled\n"); ret = -EBUSY; - goto out_unlock; + goto done; } - ret = taos_i2c_read(chip->client, (TSL258X_CMD_REG), &buf[0], 1); + ret = i2c_smbus_read_byte_data(chip->client, TSL258X_CMD_REG); if (ret < 0) { dev_err(&chip->client->dev, "taos_get_lux failed to read CMD_REG\n"); - goto out_unlock; + goto done; } + /* is data new & valid */ - if (!(buf[0] & TSL258X_STA_ADC_INTR)) { + if (!(ret & TSL258X_STA_ADC_INTR)) { dev_err(&chip->client->dev, "taos_get_lux data not valid\n"); ret = chip->als_cur_info.lux; /* return LAST VALUE */ - goto out_unlock; + goto done; } for (i = 0; i < 4; i++) { int reg = TSL258X_CMD_REG | (TSL258X_ALS_CHAN0LO + i); - ret = taos_i2c_read(chip->client, reg, &buf[i], 1); + ret = i2c_smbus_read_byte_data(chip->client, reg); if (ret < 0) { dev_err(&chip->client->dev, "taos_get_lux failed to read register %x\n", reg); - goto out_unlock; + goto done; } + buf[i] = ret; } /* @@ -252,7 +233,7 @@ static int taos_get_lux(struct iio_dev *indio_dev) dev_err(&chip->client->dev, "taos_i2c_write_command failed in taos_get_lux, err = %d\n", ret); - goto out_unlock; /* have no data, so return failure */ + goto done; /* have no data, so return failure */ } /* extract ALS/lux data */ @@ -269,7 +250,7 @@ static int taos_get_lux(struct iio_dev *indio_dev) /* have no data, so return LAST VALUE */ ret = 0; chip->als_cur_info.lux = 0; - goto out_unlock; + goto done; } /* calculate ratio */ ratio = (ch1 << 15) / ch0; @@ -295,7 +276,7 @@ static int taos_get_lux(struct iio_dev *indio_dev) dev_dbg(&chip->client->dev, "No Data - Return last value\n"); ret = 0; chip->als_cur_info.lux = 0; - goto out_unlock; + goto done; } /* adjust for active time scale */ @@ -327,8 +308,7 @@ return_max: chip->als_cur_info.lux = lux; ret = lux; -out_unlock: - mutex_unlock(&chip->als_mutex); +done: return ret; } @@ -340,39 +320,25 @@ out_unlock: static int taos_als_calibrate(struct iio_dev *indio_dev) { struct tsl2583_chip *chip = iio_priv(indio_dev); - u8 reg_val; unsigned int gain_trim_val; int ret; int lux_val; - ret = i2c_smbus_write_byte(chip->client, - (TSL258X_CMD_REG | TSL258X_CNTRL)); + ret = i2c_smbus_read_byte_data(chip->client, + TSL258X_CMD_REG | TSL258X_CNTRL); if (ret < 0) { dev_err(&chip->client->dev, - "taos_als_calibrate failed to reach the CNTRL register, ret=%d\n", - ret); + "%s failed to read from the CNTRL register\n", + __func__); return ret; } - reg_val = i2c_smbus_read_byte(chip->client); - if ((reg_val & (TSL258X_CNTL_ADC_ENBL | TSL258X_CNTL_PWR_ON)) + if ((ret & (TSL258X_CNTL_ADC_ENBL | TSL258X_CNTL_PWR_ON)) != (TSL258X_CNTL_ADC_ENBL | TSL258X_CNTL_PWR_ON)) { dev_err(&chip->client->dev, "taos_als_calibrate failed: device not powered on with ADC enabled\n"); - return -1; - } - - ret = i2c_smbus_write_byte(chip->client, - (TSL258X_CMD_REG | TSL258X_CNTRL)); - if (ret < 0) { - dev_err(&chip->client->dev, - "taos_als_calibrate failed to reach the STATUS register, ret=%d\n", - ret); - return ret; - } - reg_val = i2c_smbus_read_byte(chip->client); - - if ((reg_val & TSL258X_STA_ADC_VALID) != TSL258X_STA_ADC_VALID) { + return -EINVAL; + } else if ((ret & TSL258X_STA_ADC_VALID) != TSL258X_STA_ADC_VALID) { dev_err(&chip->client->dev, "taos_als_calibrate failed: STATUS - ADC not valid.\n"); return -ENODATA; @@ -433,17 +399,8 @@ static int taos_chip_on(struct iio_dev *indio_dev) chip->als_saturation = als_count * 922; /* 90% of full scale */ chip->als_time_scale = (als_time + 25) / 50; - /* - * TSL258x Specific power-on / adc enable sequence - * Power on the device 1st. - */ - utmp = TSL258X_CNTL_PWR_ON; - ret = i2c_smbus_write_byte_data(chip->client, - TSL258X_CMD_REG | TSL258X_CNTRL, utmp); - if (ret < 0) { - dev_err(&chip->client->dev, "taos_chip_on failed on CNTRL reg.\n"); - return ret; - } + /* Power on the device; ADC off. */ + chip->taos_config[TSL258X_CNTRL] = TSL258X_CNTL_PWR_ON; /* * Use the following shadow copy for our delay before enabling ADC. @@ -491,219 +448,60 @@ static int taos_chip_off(struct iio_dev *indio_dev) /* Sysfs Interface Functions */ -static ssize_t taos_power_state_show(struct device *dev, - struct device_attribute *attr, char *buf) +static ssize_t in_illuminance_input_target_show(struct device *dev, + struct device_attribute *attr, + char *buf) { struct iio_dev *indio_dev = dev_to_iio_dev(dev); struct tsl2583_chip *chip = iio_priv(indio_dev); + int ret; - return sprintf(buf, "%d\n", chip->taos_chip_status); -} - -static ssize_t taos_power_state_store(struct device *dev, - struct device_attribute *attr, - const char *buf, size_t len) -{ - struct iio_dev *indio_dev = dev_to_iio_dev(dev); - int value; - - if (kstrtoint(buf, 0, &value)) - return -EINVAL; - - if (!value) - taos_chip_off(indio_dev); - else - taos_chip_on(indio_dev); - - return len; -} - -static ssize_t taos_gain_show(struct device *dev, - struct device_attribute *attr, char *buf) -{ - struct iio_dev *indio_dev = dev_to_iio_dev(dev); - struct tsl2583_chip *chip = iio_priv(indio_dev); - char gain[4] = {0}; - - switch (chip->taos_settings.als_gain) { - case 0: - strcpy(gain, "001"); - break; - case 1: - strcpy(gain, "008"); - break; - case 2: - strcpy(gain, "016"); - break; - case 3: - strcpy(gain, "111"); - break; - } - - return sprintf(buf, "%s\n", gain); -} - -static ssize_t taos_gain_store(struct device *dev, - struct device_attribute *attr, - const char *buf, size_t len) -{ - struct iio_dev *indio_dev = dev_to_iio_dev(dev); - struct tsl2583_chip *chip = iio_priv(indio_dev); - int value; - - if (kstrtoint(buf, 0, &value)) - return -EINVAL; - - switch (value) { - case 1: - chip->taos_settings.als_gain = 0; - break; - case 8: - chip->taos_settings.als_gain = 1; - break; - case 16: - chip->taos_settings.als_gain = 2; - break; - case 111: - chip->taos_settings.als_gain = 3; - break; - default: - dev_err(dev, "Invalid Gain Index (must be 1,8,16,111)\n"); - return -1; - } - - return len; -} - -static ssize_t taos_gain_available_show(struct device *dev, - struct device_attribute *attr, - char *buf) -{ - return sprintf(buf, "%s\n", "1 8 16 111"); -} - -static ssize_t taos_als_time_show(struct device *dev, - struct device_attribute *attr, char *buf) -{ - struct iio_dev *indio_dev = dev_to_iio_dev(dev); - struct tsl2583_chip *chip = iio_priv(indio_dev); - - return sprintf(buf, "%d\n", chip->taos_settings.als_time); -} - -static ssize_t taos_als_time_store(struct device *dev, - struct device_attribute *attr, - const char *buf, size_t len) -{ - struct iio_dev *indio_dev = dev_to_iio_dev(dev); - struct tsl2583_chip *chip = iio_priv(indio_dev); - int value; - - if (kstrtoint(buf, 0, &value)) - return -EINVAL; - - if ((value < 50) || (value > 650)) - return -EINVAL; - - if (value % 50) - return -EINVAL; - - chip->taos_settings.als_time = value; - - return len; -} - -static ssize_t taos_als_time_available_show(struct device *dev, - struct device_attribute *attr, - char *buf) -{ - return sprintf(buf, "%s\n", - "50 100 150 200 250 300 350 400 450 500 550 600 650"); -} - -static ssize_t taos_als_trim_show(struct device *dev, - struct device_attribute *attr, char *buf) -{ - struct iio_dev *indio_dev = dev_to_iio_dev(dev); - struct tsl2583_chip *chip = iio_priv(indio_dev); + mutex_lock(&chip->als_mutex); + ret = sprintf(buf, "%d\n", chip->taos_settings.als_cal_target); + mutex_unlock(&chip->als_mutex); - return sprintf(buf, "%d\n", chip->taos_settings.als_gain_trim); + return ret; } -static ssize_t taos_als_trim_store(struct device *dev, - struct device_attribute *attr, - const char *buf, size_t len) +static ssize_t in_illuminance_input_target_store(struct device *dev, + struct device_attribute *attr, + const char *buf, size_t len) { struct iio_dev *indio_dev = dev_to_iio_dev(dev); struct tsl2583_chip *chip = iio_priv(indio_dev); int value; - if (kstrtoint(buf, 0, &value)) + if (kstrtoint(buf, 0, &value) || !value) return -EINVAL; - if (value) - chip->taos_settings.als_gain_trim = value; + mutex_lock(&chip->als_mutex); + chip->taos_settings.als_cal_target = value; + mutex_unlock(&chip->als_mutex); return len; } -static ssize_t taos_als_cal_target_show(struct device *dev, - struct device_attribute *attr, - char *buf) +static ssize_t in_illuminance_calibrate_store(struct device *dev, + struct device_attribute *attr, + const char *buf, size_t len) { struct iio_dev *indio_dev = dev_to_iio_dev(dev); struct tsl2583_chip *chip = iio_priv(indio_dev); - - return sprintf(buf, "%d\n", chip->taos_settings.als_cal_target); -} - -static ssize_t taos_als_cal_target_store(struct device *dev, - struct device_attribute *attr, - const char *buf, size_t len) -{ - struct iio_dev *indio_dev = dev_to_iio_dev(dev); - struct tsl2583_chip *chip = iio_priv(indio_dev); - int value; - - if (kstrtoint(buf, 0, &value)) - return -EINVAL; - - if (value) - chip->taos_settings.als_cal_target = value; - - return len; -} - -static ssize_t taos_lux_show(struct device *dev, struct device_attribute *attr, - char *buf) -{ - int ret; - - ret = taos_get_lux(dev_to_iio_dev(dev)); - if (ret < 0) - return ret; - - return sprintf(buf, "%d\n", ret); -} - -static ssize_t taos_do_calibrate(struct device *dev, - struct device_attribute *attr, - const char *buf, size_t len) -{ - struct iio_dev *indio_dev = dev_to_iio_dev(dev); int value; - if (kstrtoint(buf, 0, &value)) + if (kstrtoint(buf, 0, &value) || value != 1) return -EINVAL; - if (value == 1) - taos_als_calibrate(indio_dev); + mutex_lock(&chip->als_mutex); + taos_als_calibrate(indio_dev); + mutex_unlock(&chip->als_mutex); return len; } -static ssize_t taos_luxtable_show(struct device *dev, - struct device_attribute *attr, char *buf) +static ssize_t in_illuminance_lux_table_show(struct device *dev, + struct device_attribute *attr, + char *buf) { int i; int offset = 0; @@ -727,14 +525,16 @@ static ssize_t taos_luxtable_show(struct device *dev, return offset; } -static ssize_t taos_luxtable_store(struct device *dev, - struct device_attribute *attr, - const char *buf, size_t len) +static ssize_t in_illuminance_lux_table_store(struct device *dev, + struct device_attribute *attr, + const char *buf, size_t len) { struct iio_dev *indio_dev = dev_to_iio_dev(dev); struct tsl2583_chip *chip = iio_priv(indio_dev); int value[ARRAY_SIZE(taos_device_lux) * 3 + 1]; - int n; + int n, ret = -EINVAL; + + mutex_lock(&chip->als_mutex); get_options(buf, ARRAY_SIZE(value), value); @@ -746,60 +546,38 @@ static ssize_t taos_luxtable_store(struct device *dev, n = value[0]; if ((n % 3) || n < 6 || n > ((ARRAY_SIZE(taos_device_lux) - 1) * 3)) { dev_info(dev, "LUX TABLE INPUT ERROR 1 Value[0]=%d\n", n); - return -EINVAL; + goto done; } if ((value[(n - 2)] | value[(n - 1)] | value[n]) != 0) { dev_info(dev, "LUX TABLE INPUT ERROR 2 Value[0]=%d\n", n); - return -EINVAL; + goto done; } - if (chip->taos_chip_status == TSL258X_CHIP_WORKING) - taos_chip_off(indio_dev); - /* Zero out the table */ memset(taos_device_lux, 0, sizeof(taos_device_lux)); memcpy(taos_device_lux, &value[1], (value[0] * 4)); - taos_chip_on(indio_dev); - - return len; -} + ret = len; -static DEVICE_ATTR(power_state, S_IRUGO | S_IWUSR, - taos_power_state_show, taos_power_state_store); - -static DEVICE_ATTR(illuminance0_calibscale, S_IRUGO | S_IWUSR, - taos_gain_show, taos_gain_store); -static DEVICE_ATTR(illuminance0_calibscale_available, S_IRUGO, - taos_gain_available_show, NULL); - -static DEVICE_ATTR(illuminance0_integration_time, S_IRUGO | S_IWUSR, - taos_als_time_show, taos_als_time_store); -static DEVICE_ATTR(illuminance0_integration_time_available, S_IRUGO, - taos_als_time_available_show, NULL); - -static DEVICE_ATTR(illuminance0_calibbias, S_IRUGO | S_IWUSR, - taos_als_trim_show, taos_als_trim_store); +done: + mutex_unlock(&chip->als_mutex); -static DEVICE_ATTR(illuminance0_input_target, S_IRUGO | S_IWUSR, - taos_als_cal_target_show, taos_als_cal_target_store); + return ret; +} -static DEVICE_ATTR(illuminance0_input, S_IRUGO, taos_lux_show, NULL); -static DEVICE_ATTR(illuminance0_calibrate, S_IWUSR, NULL, taos_do_calibrate); -static DEVICE_ATTR(illuminance0_lux_table, S_IRUGO | S_IWUSR, - taos_luxtable_show, taos_luxtable_store); +static IIO_CONST_ATTR(in_illuminance_calibscale_available, "1 8 16 111"); +static IIO_CONST_ATTR(in_illuminance_integration_time_available, + "0.000050 0.000100 0.000150 0.000200 0.000250 0.000300 0.000350 0.000400 0.000450 0.000500 0.000550 0.000600 0.000650"); +static IIO_DEVICE_ATTR_RW(in_illuminance_input_target, 0); +static IIO_DEVICE_ATTR_WO(in_illuminance_calibrate, 0); +static IIO_DEVICE_ATTR_RW(in_illuminance_lux_table, 0); static struct attribute *sysfs_attrs_ctrl[] = { - &dev_attr_power_state.attr, - &dev_attr_illuminance0_calibscale.attr, /* Gain */ - &dev_attr_illuminance0_calibscale_available.attr, - &dev_attr_illuminance0_integration_time.attr, /* I time*/ - &dev_attr_illuminance0_integration_time_available.attr, - &dev_attr_illuminance0_calibbias.attr, /* trim */ - &dev_attr_illuminance0_input_target.attr, - &dev_attr_illuminance0_input.attr, - &dev_attr_illuminance0_calibrate.attr, - &dev_attr_illuminance0_lux_table.attr, + &iio_const_attr_in_illuminance_calibscale_available.dev_attr.attr, + &iio_const_attr_in_illuminance_integration_time_available.dev_attr.attr, + &iio_dev_attr_in_illuminance_input_target.dev_attr.attr, + &iio_dev_attr_in_illuminance_calibrate.dev_attr.attr, + &iio_dev_attr_in_illuminance_lux_table.dev_attr.attr, NULL }; @@ -807,15 +585,161 @@ static const struct attribute_group tsl2583_attribute_group = { .attrs = sysfs_attrs_ctrl, }; -/* Use the default register values to identify the Taos device */ -static int taos_tsl258x_device(unsigned char *bufp) +static const struct iio_chan_spec tsl2583_channels[] = { + { + .type = IIO_LIGHT, + .modified = 1, + .channel2 = IIO_MOD_LIGHT_IR, + .info_mask_separate = BIT(IIO_CHAN_INFO_RAW), + }, + { + .type = IIO_LIGHT, + .modified = 1, + .channel2 = IIO_MOD_LIGHT_BOTH, + .info_mask_separate = BIT(IIO_CHAN_INFO_RAW), + }, + { + .type = IIO_LIGHT, + .info_mask_separate = BIT(IIO_CHAN_INFO_PROCESSED) | + BIT(IIO_CHAN_INFO_CALIBBIAS) | + BIT(IIO_CHAN_INFO_CALIBSCALE) | + BIT(IIO_CHAN_INFO_INT_TIME), + }, +}; + +static int tsl2583_read_raw(struct iio_dev *indio_dev, + struct iio_chan_spec const *chan, + int *val, int *val2, long mask) +{ + struct tsl2583_chip *chip = iio_priv(indio_dev); + int ret = -EINVAL; + + mutex_lock(&chip->als_mutex); + + if (chip->taos_chip_status != TSL258X_CHIP_WORKING) { + ret = -EBUSY; + goto read_done; + } + + switch (mask) { + case IIO_CHAN_INFO_RAW: + if (chan->type == IIO_LIGHT) { + ret = taos_get_lux(indio_dev); + if (ret < 0) + goto read_done; + + /* + * From page 20 of the TSL2581, TSL2583 data + * sheet (TAOS134 − MARCH 2011): + * + * One of the photodiodes (channel 0) is + * sensitive to both visible and infrared light, + * while the second photodiode (channel 1) is + * sensitive primarily to infrared light. + */ + if (chan->channel2 == IIO_MOD_LIGHT_BOTH) + *val = chip->als_cur_info.als_ch0; + else + *val = chip->als_cur_info.als_ch1; + + ret = IIO_VAL_INT; + } + break; + case IIO_CHAN_INFO_PROCESSED: + if (chan->type == IIO_LIGHT) { + ret = taos_get_lux(indio_dev); + if (ret < 0) + goto read_done; + + *val = ret; + ret = IIO_VAL_INT; + } + break; + case IIO_CHAN_INFO_CALIBBIAS: + if (chan->type == IIO_LIGHT) { + *val = chip->taos_settings.als_gain_trim; + ret = IIO_VAL_INT; + } + break; + case IIO_CHAN_INFO_CALIBSCALE: + if (chan->type == IIO_LIGHT) { + *val = gainadj[chip->taos_settings.als_gain].mean; + ret = IIO_VAL_INT; + } + break; + case IIO_CHAN_INFO_INT_TIME: + if (chan->type == IIO_LIGHT) { + *val = 0; + *val2 = chip->taos_settings.als_time; + ret = IIO_VAL_INT_PLUS_MICRO; + } + break; + default: + break; + } + +read_done: + mutex_unlock(&chip->als_mutex); + + return ret; +} + +static int tsl2583_write_raw(struct iio_dev *indio_dev, + struct iio_chan_spec const *chan, + int val, int val2, long mask) { - return ((bufp[TSL258X_CHIPID] & 0xf0) == 0x90); + struct tsl2583_chip *chip = iio_priv(indio_dev); + int ret = -EINVAL; + + mutex_lock(&chip->als_mutex); + + if (chip->taos_chip_status != TSL258X_CHIP_WORKING) { + ret = -EBUSY; + goto write_done; + } + + switch (mask) { + case IIO_CHAN_INFO_CALIBBIAS: + if (chan->type == IIO_LIGHT) { + chip->taos_settings.als_gain_trim = val; + ret = 0; + } + break; + case IIO_CHAN_INFO_CALIBSCALE: + if (chan->type == IIO_LIGHT) { + int i; + + for (i = 0; i < ARRAY_SIZE(gainadj); i++) { + if (gainadj[i].mean == val) { + chip->taos_settings.als_gain = i; + ret = 0; + break; + } + } + } + break; + case IIO_CHAN_INFO_INT_TIME: + if (chan->type == IIO_LIGHT && !val && val2 >= 50 && + val2 <= 650 && !(val2 % 50)) { + chip->taos_settings.als_time = val2; + ret = 0; + } + break; + default: + break; + } + +write_done: + mutex_unlock(&chip->als_mutex); + + return ret; } static const struct iio_info tsl2583_info = { .attrs = &tsl2583_attribute_group, .driver_module = THIS_MODULE, + .read_raw = tsl2583_read_raw, + .write_raw = tsl2583_write_raw, }; /* @@ -825,8 +749,7 @@ static const struct iio_info tsl2583_info = { static int taos_probe(struct i2c_client *clientp, const struct i2c_device_id *idp) { - int i, ret; - unsigned char buf[TSL258X_MAX_DEVICE_REGS]; + int ret; struct tsl2583_chip *chip; struct iio_dev *indio_dev; @@ -847,28 +770,17 @@ static int taos_probe(struct i2c_client *clientp, chip->taos_chip_status = TSL258X_CHIP_UNKNOWN; memcpy(chip->taos_config, taos_config, sizeof(chip->taos_config)); - for (i = 0; i < TSL258X_MAX_DEVICE_REGS; i++) { - ret = i2c_smbus_write_byte(clientp, - (TSL258X_CMD_REG | (TSL258X_CNTRL + i))); - if (ret < 0) { - dev_err(&clientp->dev, - "i2c_smbus_write_byte to cmd reg failed in taos_probe(), err = %d\n", - ret); - return ret; - } - ret = i2c_smbus_read_byte(clientp); - if (ret < 0) { - dev_err(&clientp->dev, - "i2c_smbus_read_byte from reg failed in taos_probe(), err = %d\n", - ret); - return ret; - } - buf[i] = ret; + ret = i2c_smbus_read_byte_data(clientp, + TSL258X_CMD_REG | TSL258X_CHIPID); + if (ret < 0) { + dev_err(&clientp->dev, + "%s failed to read the chip ID register\n", __func__); + return ret; } - if (!taos_tsl258x_device(buf)) { - dev_info(&clientp->dev, - "i2c device found but does not match expected id in taos_probe()\n"); + if ((ret & TSL2583_CHIP_ID_MASK) != TSL2583_CHIP_ID) { + dev_info(&clientp->dev, "%s received an unknown chip ID %x\n", + __func__, ret); return -EINVAL; } @@ -881,6 +793,8 @@ static int taos_probe(struct i2c_client *clientp, } indio_dev->info = &tsl2583_info; + indio_dev->channels = tsl2583_channels; + indio_dev->num_channels = ARRAY_SIZE(tsl2583_channels); indio_dev->dev.parent = &clientp->dev; indio_dev->modes = INDIO_DIRECT_MODE; indio_dev->name = chip->client->name; @@ -894,7 +808,9 @@ static int taos_probe(struct i2c_client *clientp, taos_defaults(chip); /* Make sure the chip is on */ - taos_chip_on(indio_dev); + ret = taos_chip_on(indio_dev); + if (ret < 0) + return ret; dev_info(&clientp->dev, "Light sensor found.\n"); return 0; @@ -947,11 +863,24 @@ static struct i2c_device_id taos_idtable[] = { }; MODULE_DEVICE_TABLE(i2c, taos_idtable); +#ifdef CONFIG_OF +static const struct of_device_id taos2583_of_match[] = { + { .compatible = "amstaos,tsl2580", }, + { .compatible = "amstaos,tsl2581", }, + { .compatible = "amstaos,tsl2583", }, + { }, +}; +MODULE_DEVICE_TABLE(of, taos2583_of_match); +#else +#define taos2583_of_match NULL +#endif + /* Driver definition */ static struct i2c_driver taos_driver = { .driver = { .name = "tsl2583", .pm = TAOS_PM_OPS, + .of_match_table = taos2583_of_match, }, .id_table = taos_idtable, .probe = taos_probe, diff --git a/include/linux/mfd/cros_ec.h b/include/linux/mfd/cros_ec.h index 76f7ef4d3a0d..f62043a75f43 100644 --- a/include/linux/mfd/cros_ec.h +++ b/include/linux/mfd/cros_ec.h @@ -148,6 +148,15 @@ struct cros_ec_device { int event_size; }; +/** + * struct cros_ec_sensor_platform - ChromeOS EC sensor platform information + * + * @sensor_num: Id of the sensor, as reported by the EC. + */ +struct cros_ec_sensor_platform { + u8 sensor_num; +}; + /* struct cros_ec_platform - ChromeOS EC platform information * * @ec_name: name of EC device (e.g. 'cros-ec', 'cros-pd', ...) @@ -175,6 +184,7 @@ struct cros_ec_dev { struct cros_ec_device *ec_dev; struct device *dev; u16 cmd_offset; + u32 features[2]; }; /** diff --git a/include/linux/mfd/cros_ec_commands.h b/include/linux/mfd/cros_ec_commands.h index 76728ff37d01..1683003603f3 100644 --- a/include/linux/mfd/cros_ec_commands.h +++ b/include/linux/mfd/cros_ec_commands.h @@ -713,6 +713,90 @@ struct ec_response_get_set_value { /* More than one command can use these structs to get/set paramters. */ #define EC_CMD_GSV_PAUSE_IN_S5 0x0c +/*****************************************************************************/ +/* List the features supported by the firmware */ +#define EC_CMD_GET_FEATURES 0x0d + +/* Supported features */ +enum ec_feature_code { + /* + * This image contains a limited set of features. Another image + * in RW partition may support more features. + */ + EC_FEATURE_LIMITED = 0, + /* + * Commands for probing/reading/writing/erasing the flash in the + * EC are present. + */ + EC_FEATURE_FLASH = 1, + /* + * Can control the fan speed directly. + */ + EC_FEATURE_PWM_FAN = 2, + /* + * Can control the intensity of the keyboard backlight. + */ + EC_FEATURE_PWM_KEYB = 3, + /* + * Support Google lightbar, introduced on Pixel. + */ + EC_FEATURE_LIGHTBAR = 4, + /* Control of LEDs */ + EC_FEATURE_LED = 5, + /* Exposes an interface to control gyro and sensors. + * The host goes through the EC to access these sensors. + * In addition, the EC may provide composite sensors, like lid angle. + */ + EC_FEATURE_MOTION_SENSE = 6, + /* The keyboard is controlled by the EC */ + EC_FEATURE_KEYB = 7, + /* The AP can use part of the EC flash as persistent storage. */ + EC_FEATURE_PSTORE = 8, + /* The EC monitors BIOS port 80h, and can return POST codes. */ + EC_FEATURE_PORT80 = 9, + /* + * Thermal management: include TMP specific commands. + * Higher level than direct fan control. + */ + EC_FEATURE_THERMAL = 10, + /* Can switch the screen backlight on/off */ + EC_FEATURE_BKLIGHT_SWITCH = 11, + /* Can switch the wifi module on/off */ + EC_FEATURE_WIFI_SWITCH = 12, + /* Monitor host events, through for example SMI or SCI */ + EC_FEATURE_HOST_EVENTS = 13, + /* The EC exposes GPIO commands to control/monitor connected devices. */ + EC_FEATURE_GPIO = 14, + /* The EC can send i2c messages to downstream devices. */ + EC_FEATURE_I2C = 15, + /* Command to control charger are included */ + EC_FEATURE_CHARGER = 16, + /* Simple battery support. */ + EC_FEATURE_BATTERY = 17, + /* + * Support Smart battery protocol + * (Common Smart Battery System Interface Specification) + */ + EC_FEATURE_SMART_BATTERY = 18, + /* EC can dectect when the host hangs. */ + EC_FEATURE_HANG_DETECT = 19, + /* Report power information, for pit only */ + EC_FEATURE_PMU = 20, + /* Another Cros EC device is present downstream of this one */ + EC_FEATURE_SUB_MCU = 21, + /* Support USB Power delivery (PD) commands */ + EC_FEATURE_USB_PD = 22, + /* Control USB multiplexer, for audio through USB port for instance. */ + EC_FEATURE_USB_MUX = 23, + /* Motion Sensor code has an internal software FIFO */ + EC_FEATURE_MOTION_SENSE_FIFO = 24, +}; + +#define EC_FEATURE_MASK_0(event_code) (1UL << (event_code % 32)) +#define EC_FEATURE_MASK_1(event_code) (1UL << (event_code - 32)) +struct ec_response_get_features { + uint32_t flags[2]; +} __packed; /*****************************************************************************/ /* Flash commands */ @@ -1315,6 +1399,24 @@ enum motionsense_command { */ MOTIONSENSE_CMD_KB_WAKE_ANGLE = 5, + /* + * Returns a single sensor data. + */ + MOTIONSENSE_CMD_DATA = 6, + + /* + * Perform low level calibration.. On sensors that support it, ask to + * do offset calibration. + */ + MOTIONSENSE_CMD_PERFORM_CALIB = 10, + + /* + * Sensor Offset command is a setter/getter command for the offset used + * for calibration. The offsets can be calculated by the host, or via + * PERFORM_CALIB command. + */ + MOTIONSENSE_CMD_SENSOR_OFFSET = 11, + /* Number of motionsense sub-commands. */ MOTIONSENSE_NUM_CMDS }; @@ -1335,12 +1437,18 @@ enum motionsensor_id { enum motionsensor_type { MOTIONSENSE_TYPE_ACCEL = 0, MOTIONSENSE_TYPE_GYRO = 1, + MOTIONSENSE_TYPE_MAG = 2, + MOTIONSENSE_TYPE_PROX = 3, + MOTIONSENSE_TYPE_LIGHT = 4, + MOTIONSENSE_TYPE_ACTIVITY = 5, + MOTIONSENSE_TYPE_MAX }; /* List of motion sensor locations. */ enum motionsensor_location { MOTIONSENSE_LOC_BASE = 0, MOTIONSENSE_LOC_LID = 1, + MOTIONSENSE_LOC_MAX, }; /* List of motion sensor chips. */ @@ -1361,6 +1469,31 @@ enum motionsensor_chip { */ #define EC_MOTION_SENSE_NO_VALUE -1 +#define EC_MOTION_SENSE_INVALID_CALIB_TEMP 0x8000 + +/* Set Calibration information */ +#define MOTION_SENSE_SET_OFFSET 1 + +struct ec_response_motion_sensor_data { + /* Flags for each sensor. */ + uint8_t flags; + /* Sensor number the data comes from */ + uint8_t sensor_num; + /* Each sensor is up to 3-axis. */ + union { + int16_t data[3]; + struct { + uint16_t rsvd; + uint32_t timestamp; + } __packed; + struct { + uint8_t activity; /* motionsensor_activity */ + uint8_t state; + int16_t add_info[2]; + }; + }; +} __packed; + struct ec_params_motion_sense { uint8_t cmd; union { @@ -1378,9 +1511,37 @@ struct ec_params_motion_sense { int16_t data; } ec_rate, kb_wake_angle; + /* Used for MOTIONSENSE_CMD_SENSOR_OFFSET */ + struct { + uint8_t sensor_num; + + /* + * bit 0: If set (MOTION_SENSE_SET_OFFSET), set + * the calibration information in the EC. + * If unset, just retrieve calibration information. + */ + uint16_t flags; + + /* + * Temperature at calibration, in units of 0.01 C + * 0x8000: invalid / unknown. + * 0x0: 0C + * 0x7fff: +327.67C + */ + int16_t temp; + + /* + * Offset for calibration. + * Unit: + * Accelerometer: 1/1024 g + * Gyro: 1/1024 deg/s + * Compass: 1/16 uT + */ + int16_t offset[3]; + } __packed sensor_offset; + /* Used for MOTIONSENSE_CMD_INFO. */ struct { - /* Should be element of enum motionsensor_id. */ uint8_t sensor_num; } info; @@ -1410,11 +1571,14 @@ struct ec_response_motion_sense { /* Flags representing the motion sensor module. */ uint8_t module_flags; - /* Flags for each sensor in enum motionsensor_id. */ - uint8_t sensor_flags[EC_MOTION_SENSOR_COUNT]; + /* Number of sensors managed directly by the EC. */ + uint8_t sensor_count; - /* Array of all sensor data. Each sensor is 3-axis. */ - int16_t data[3*EC_MOTION_SENSOR_COUNT]; + /* + * Sensor data is truncated if response_max is too small + * for holding all the data. + */ + struct ec_response_motion_sensor_data sensor[0]; } dump; /* Used for MOTIONSENSE_CMD_INFO. */ @@ -1429,6 +1593,9 @@ struct ec_response_motion_sense { uint8_t chip; } info; + /* Used for MOTIONSENSE_CMD_DATA */ + struct ec_response_motion_sensor_data data; + /* * Used for MOTIONSENSE_CMD_EC_RATE, MOTIONSENSE_CMD_SENSOR_ODR, * MOTIONSENSE_CMD_SENSOR_RANGE, and @@ -1438,6 +1605,12 @@ struct ec_response_motion_sense { /* Current value of the parameter queried. */ int32_t ret; } ec_rate, sensor_odr, sensor_range, kb_wake_angle; + + /* Used for MOTIONSENSE_CMD_SENSOR_OFFSET */ + struct { + int16_t temp; + int16_t offset[3]; + } sensor_offset, perform_calib; }; } __packed; diff --git a/include/linux/mfd/ti_am335x_tscadc.h b/include/linux/mfd/ti_am335x_tscadc.h index 7f55b8b41032..b9a53e013bff 100644 --- a/include/linux/mfd/ti_am335x_tscadc.h +++ b/include/linux/mfd/ti_am335x_tscadc.h @@ -23,6 +23,8 @@ #define REG_IRQENABLE 0x02C #define REG_IRQCLR 0x030 #define REG_IRQWAKEUP 0x034 +#define REG_DMAENABLE_SET 0x038 +#define REG_DMAENABLE_CLEAR 0x03c #define REG_CTRL 0x040 #define REG_ADCFSM 0x044 #define REG_CLKDIV 0x04C @@ -36,6 +38,7 @@ #define REG_FIFO0THR 0xE8 #define REG_FIFO1CNT 0xF0 #define REG_FIFO1THR 0xF4 +#define REG_DMA1REQ 0xF8 #define REG_FIFO0 0x100 #define REG_FIFO1 0x200 @@ -126,6 +129,10 @@ #define FIFOREAD_DATA_MASK (0xfff << 0) #define FIFOREAD_CHNLID_MASK (0xf << 16) +/* DMA ENABLE/CLEAR Register */ +#define DMA_FIFO0 BIT(0) +#define DMA_FIFO1 BIT(1) + /* Sequencer Status */ #define SEQ_STATUS BIT(5) #define CHARGE_STEP 0x11 @@ -155,6 +162,7 @@ struct ti_tscadc_dev { struct device *dev; struct regmap *regmap; void __iomem *tscadc_base; + phys_addr_t tscadc_phys_base; int irq; int used_cells; /* 1-2 */ int tsc_wires; |