summaryrefslogtreecommitdiff
diff options
context:
space:
mode:
-rw-r--r--Documentation/hwmon/ds162180
1 files changed, 50 insertions, 30 deletions
diff --git a/Documentation/hwmon/ds1621 b/Documentation/hwmon/ds1621
index c0817f7934e4..896cdc972ca8 100644
--- a/Documentation/hwmon/ds1621
+++ b/Documentation/hwmon/ds1621
@@ -73,37 +73,57 @@ any of the limits have ever been met or exceeded since last power-up or
reset. Be aware: When testing, it showed that the status of Tout can change
with neither of the alarms set.
-Temperature conversion of the DS1621 takes up to 1000ms; internal access to
-non-volatile registers may last for 10ms or below.
-
-The DS1625 is pin compatible and functionally equivalent with the DS1621,
-but the DS1621 is meant to replace it. The DS1631, DS1721, and DS1731 are
-also pin compatible with the DS1621, but provide multi-resolution support.
-
Since there is no version or vendor identification register, there is
no unique identification for these devices. Therefore, explicit device
-instantiation is required for correct device identification and functionality.
-
-And, for correct identification and operation, each device must be
-explicitly instantiated, one device per address, in this address
-range: 0x48..0x4f.
+instantiation is required for correct device identification and functionality
+(one device per address in this address range: 0x48..0x4f).
-The DS1721 is pin compatible with the DS1621, has an accuracy of +/- 1.0
-degree Celsius (from -10 to +85 degrees), a minimum/maximum alarm default
-setting of 75 and 80 degrees, and a maximum conversion time of 750ms.
-
-In addition, the DS1721 supports four resolution settings from 9 to 12 bits
-(defined in degrees C per LSB: 0.5, 0.25, 0.125, and 0.0625, respectively),
-that are set at device power on to the highest resolution: 12-bits.
-
-One additional note about the ds1721 is that although the data sheet says
-the temperature flags (THF and TLF) are used internally, these flags do
-get set and cleared as the actual temperature crosses the min or max settings.
-
-The DS1631 and DS1731 are pin compatible with the DS1621 and feature compatible
-with the DS1721. However, the DS1631 accuracy is +/- 0.5 degree Celsius (from 0
-to +70 degrees), while the DS1731 accuracy is +/-1 degree Celsius (from -10 to
-+85 degrees).
+The DS1625 is pin compatible and functionally equivalent with the DS1621,
+but the DS1621 is meant to replace it. The DS1631, DS1721, and DS1731 are
+also pin compatible with the DS1621 and provide multi-resolution support.
+
+Additionally, the DS1721 data sheet says the temperature flags (THF and TLF)
+are used internally, however, these flags do get set and cleared as the actual
+temperature crosses the min or max settings (which by default are set to 75
+and 80 degrees respectively).
+
+Temperature Conversion:
+-----------------------
+DS1621 - 750ms (older devices may take up to 1000ms)
+DS1625 - 500ms
+DS1631 - 93ms..750ms for 9..12 bits resolution, respectively.
+DS1721 - 93ms..750ms for 9..12 bits resolution, respectively.
+DS1731 - 93ms..750ms for 9..12 bits resolution, respectively.
+
+Note:
+On the DS1621, internal access to non-volatile registers may last for 10ms
+or less (unverified on the other devices).
+
+Temperature Accuracy:
+---------------------
+DS1621: +/- 0.5 degree Celsius (from 0 to +70 degrees)
+DS1625: +/- 0.5 degree Celsius (from 0 to +70 degrees)
+DS1631: +/- 0.5 degree Celsius (from 0 to +70 degrees)
+DS1721: +/- 1.0 degree Celsius (from -10 to +85 degrees)
+DS1731: +/- 1.0 degree Celsius (from -10 to +85 degrees)
+
+Note:
+Please refer to the device datasheets for accuracy at other temperatures.
+
+Temperature Resolution:
+-----------------------
+As mentioned above, the DS1631, DS1721, and DS1731 provide multi-resolution
+support, which is achieved via the R0 and R1 config register bits, where:
+
+R0..R1
+------
+ 0 0 => 9 bits, 0.5 degrees Celcius
+ 1 0 => 10 bits, 0.25 degrees Celcius
+ 0 1 => 11 bits, 0.125 degrees Celcius
+ 1 1 => 12 bits, 0.0625 degrees Celcius
+
+Note:
+At initial device power-on, the default resolution is set to 12-bits.
The resolution mode for the DS1631, DS1721, or DS1731 can be changed from
userspace, via the device 'update_interval' sysfs attribute. This attribute
@@ -112,12 +132,12 @@ values defined in the datasheet as follows:
Resolution Conversion Time Input Range
(C/LSB) (msec) (msec)
---------------------------------------------
+------------------------------------------------
0.5 93.75 0....94
0.25 187.5 95...187
0.125 375 188..375
0.0625 750 376..infinity
---------------------------------------
+------------------------------------------------
The following examples show how the 'update_interval' attribute can be
used to change the conversion time: