diff options
| -rw-r--r-- | Documentation/hwmon/index.rst | 1 | ||||
| -rw-r--r-- | Documentation/hwmon/ltc4282.rst | 133 | ||||
| -rw-r--r-- | MAINTAINERS | 2 | ||||
| -rw-r--r-- | drivers/hwmon/Kconfig | 11 | ||||
| -rw-r--r-- | drivers/hwmon/Makefile | 1 | ||||
| -rw-r--r-- | drivers/hwmon/ltc4282.c | 1782 |
6 files changed, 1930 insertions, 0 deletions
diff --git a/Documentation/hwmon/index.rst b/Documentation/hwmon/index.rst index c7ed1f73ac06..f16c6dfaec7d 100644 --- a/Documentation/hwmon/index.rst +++ b/Documentation/hwmon/index.rst @@ -129,6 +129,7 @@ Hardware Monitoring Kernel Drivers ltc4245 ltc4260 ltc4261 + ltc4282 ltc4286 max127 max15301 diff --git a/Documentation/hwmon/ltc4282.rst b/Documentation/hwmon/ltc4282.rst new file mode 100644 index 000000000000..a87ec3564998 --- /dev/null +++ b/Documentation/hwmon/ltc4282.rst @@ -0,0 +1,133 @@ +.. SPDX-License-Identifier: GPL-2.0-only + +Kernel drivers ltc4282 +========================================== + +Supported chips: + + * Analog Devices LTC4282 + + Prefix: 'ltc4282' + + Addresses scanned: - I2C 0x40 - 0x5A (7-bit) + Addresses scanned: - I2C 0x80 - 0xB4 with a step of 2 (8-bit) + + Datasheet: + + https://www.analog.com/media/en/technical-documentation/data-sheets/ltc4282.pdf + +Author: Nuno Sá <nuno.sa@analog.com> + +Description +___________ + +The LTC4282 hot swap controller allows a board to be safely inserted and removed +from a live backplane. Using one or more external N-channel pass transistors, +board supply voltage and inrush current are ramped up at an adjustable rate. An +I2C interface and onboard ADC allows for monitoring of board current, voltage, +power, energy and fault status. The device features analog foldback current +limiting and supply monitoring for applications from 2.9V to 33V. Dual 12V gate +drive allows high power applications to either share safe operating area across +parallel MOSFETs or support a 2-stage start-up that first charges the load +capacitance followed by enabling a low on-resistance path to the load. The +LTC4282 is well suited to high power applications because the precise monitoring +capability and accurate current limiting reduce the extremes in which both loads +and power supplies must safely operate. Non-volatile configuration allows for +flexibility in the autonomous generation of alerts and response to faults. + +Sysfs entries +_____________ + +The following attributes are supported. Limits are read-write and all the other +attributes are read-only. Note that in0 and in1 are mutually exclusive. Enabling +one disables the other and disabling one enables the other. + +======================= ========================================== +in0_input Output voltage (mV). +in0_min Undervoltage threshold +in0_max Overvoltage threshold +in0_lowest Lowest measured voltage +in0_highest Highest measured voltage +in0_reset_history Write 1 to reset in0 history. + Also clears fet bad and short fault logs. +in0_min_alarm Undervoltage alarm +in0_max_alarm Overvoltage alarm +in0_enable Enable/Disable VSOURCE monitoring +in0_fault Failure in the MOSFETs. Either bad or shorted FET. +in0_label Channel label (VSOURCE) + +in1_input Input voltage (mV). +in1_min Undervoltage threshold +in1_max Overvoltage threshold +in1_lowest Lowest measured voltage +in1_highest Highest measured voltage +in1_reset_history Write 1 to reset in1 history. + Also clears over/undervoltage fault logs. +in1_min_alarm Undervoltage alarm +in1_max_alarm Overvoltage alarm +in1_lcrit_alarm Critical Undervoltage alarm +in1_crit_alarm Critical Overvoltage alarm +in1_enable Enable/Disable VDD monitoring +in1_label Channel label (VDD) + +in2_input GPIO voltage (mV) +in2_min Undervoltage threshold +in2_max Overvoltage threshold +in2_lowest Lowest measured voltage +in2_highest Highest measured voltage +in2_reset_history Write 1 to reset in2 history +in2_min_alarm Undervoltage alarm +in2_max_alarm Overvoltage alarm +in2_label Channel label (VGPIO) + +curr1_input Sense current (mA) +curr1_min Undercurrent threshold +curr1_max Overcurrent threshold +curr1_lowest Lowest measured current +curr1_highest Highest measured current +curr1_reset_history Write 1 to reset curr1 history. + Also clears overcurrent fault logs. +curr1_min_alarm Undercurrent alarm +curr1_max_alarm Overcurrent alarm +curr1_crit_alarm Critical Overcurrent alarm +curr1_label Channel label (ISENSE) + +power1_input Power (in uW) +power1_min Low power threshold +power1_max High power threshold +power1_input_lowest Historical minimum power use +power1_input_highest Historical maximum power use +power1_reset_history Write 1 to reset power1 history. + Also clears power bad fault logs. +power1_min_alarm Low power alarm +power1_max_alarm High power alarm +power1_label Channel label (Power) + +energy1_input Measured energy over time (in microJoule) +energy1_enable Enable/Disable Energy accumulation +======================= ========================================== + +DebugFs entries +_______________ + +The chip also has a fault log register where failures can be logged. Hence, +as these are logging events, we give access to them in debugfs. Note that +even if some failure is detected in these logs, it does necessarily mean +that the failure is still present. As mentioned in the proper Sysfs entries, +these logs can be cleared by writing in the proper reset_history attribute. + +.. warning:: The debugfs interface is subject to change without notice + and is only available when the kernel is compiled with + ``CONFIG_DEBUG_FS`` defined. + +``/sys/kernel/debug/ltc4282-hwmon[X]/`` +contains the following attributes: + +======================= ========================================== +power1_bad_fault_log Set to 1 by a power1 bad fault occurring. +in0_fet_short_fault_log Set to 1 when the ADC detects a FET-short fault. +in0_fet_bad_fault_log Set to 1 when a FET-BAD fault occurs. +in1_crit_fault_log Set to 1 by a VDD overvoltage fault occurring. +in1_lcrit_fault_log Set to 1 by a VDD undervoltage fault occurring. +curr1_crit_fault_log Set to 1 by an overcurrent fault occurring. +======================= ========================================== diff --git a/MAINTAINERS b/MAINTAINERS index 3625754d7d1b..df8ea2d94a0c 100644 --- a/MAINTAINERS +++ b/MAINTAINERS @@ -12765,6 +12765,8 @@ M: Nuno Sa <nuno.sa@analog.com> L: linux-hwmon@vger.kernel.org S: Supported F: Documentation/devicetree/bindings/hwmon/adi,ltc4282.yaml +F: Documentation/hwmon/ltc4282.rst +F: drivers/hwmon/ltc4282.c LTC4286 HARDWARE MONITOR DRIVER M: Delphine CC Chiu <Delphine_CC_Chiu@Wiwynn.com> diff --git a/drivers/hwmon/Kconfig b/drivers/hwmon/Kconfig index a608264da87d..f6160cc70077 100644 --- a/drivers/hwmon/Kconfig +++ b/drivers/hwmon/Kconfig @@ -1038,6 +1038,17 @@ config SENSORS_LTC4261 This driver can also be built as a module. If so, the module will be called ltc4261. +config SENSORS_LTC4282 + tristate "Analog Devices LTC4282" + depends on I2C + select REGMAP_I2C + help + If you say yes here you get support for Analog Devices LTC4282 + High Current Hot Swap Controller I2C interface. + + This driver can also be built as a module. If so, the module will + be called ltc4282. + config SENSORS_LTQ_CPUTEMP bool "Lantiq cpu temperature sensor driver" depends on SOC_XWAY diff --git a/drivers/hwmon/Makefile b/drivers/hwmon/Makefile index 47be39af5c03..8bfc422a29e5 100644 --- a/drivers/hwmon/Makefile +++ b/drivers/hwmon/Makefile @@ -136,6 +136,7 @@ obj-$(CONFIG_SENSORS_LTC4222) += ltc4222.o obj-$(CONFIG_SENSORS_LTC4245) += ltc4245.o obj-$(CONFIG_SENSORS_LTC4260) += ltc4260.o obj-$(CONFIG_SENSORS_LTC4261) += ltc4261.o +obj-$(CONFIG_SENSORS_LTC4282) += ltc4282.o obj-$(CONFIG_SENSORS_LTQ_CPUTEMP) += ltq-cputemp.o obj-$(CONFIG_SENSORS_MAX1111) += max1111.o obj-$(CONFIG_SENSORS_MAX127) += max127.o diff --git a/drivers/hwmon/ltc4282.c b/drivers/hwmon/ltc4282.c new file mode 100644 index 000000000000..4f608a3790fb --- /dev/null +++ b/drivers/hwmon/ltc4282.c @@ -0,0 +1,1782 @@ +// SPDX-License-Identifier: GPL-2.0 +/* + * Analog Devices LTC4282 I2C High Current Hot Swap Controller over I2C + * + * Copyright 2023 Analog Devices Inc. + */ +#include <linux/bitfield.h> +#include <linux/cleanup.h> +#include <linux/clk.h> +#include <linux/clk-provider.h> +#include <linux/debugfs.h> +#include <linux/delay.h> +#include <linux/device.h> +#include <linux/hwmon.h> +#include <linux/hwmon-sysfs.h> +#include <linux/i2c.h> +#include <linux/math.h> +#include <linux/minmax.h> +#include <linux/module.h> +#include <linux/mod_devicetable.h> +#include <linux/mutex.h> +#include <linux/regmap.h> +#include <linux/property.h> +#include <linux/string.h> +#include <linux/units.h> +#include <linux/util_macros.h> + +#define LTC4282_CTRL_LSB 0x00 + #define LTC4282_CTRL_OV_RETRY_MASK BIT(0) + #define LTC4282_CTRL_UV_RETRY_MASK BIT(1) + #define LTC4282_CTRL_OC_RETRY_MASK BIT(2) + #define LTC4282_CTRL_ON_ACTIVE_LOW_MASK BIT(5) + #define LTC4282_CTRL_ON_DELAY_MASK BIT(6) +#define LTC4282_CTRL_MSB 0x01 + #define LTC4282_CTRL_VIN_MODE_MASK GENMASK(1, 0) + #define LTC4282_CTRL_OV_MODE_MASK GENMASK(3, 2) + #define LTC4282_CTRL_UV_MODE_MASK GENMASK(5, 4) +#define LTC4282_FAULT_LOG 0x04 + #define LTC4282_OV_FAULT_MASK BIT(0) + #define LTC4282_UV_FAULT_MASK BIT(1) + #define LTC4282_VDD_FAULT_MASK \ + (LTC4282_OV_FAULT_MASK | LTC4282_UV_FAULT_MASK) + #define LTC4282_OC_FAULT_MASK BIT(2) + #define LTC4282_POWER_BAD_FAULT_MASK BIT(3) + #define LTC4282_FET_SHORT_FAULT_MASK BIT(5) + #define LTC4282_FET_BAD_FAULT_MASK BIT(6) + #define LTC4282_FET_FAILURE_FAULT_MASK \ + (LTC4282_FET_SHORT_FAULT_MASK | LTC4282_FET_BAD_FAULT_MASK) +#define LTC4282_ADC_ALERT_LOG 0x05 + #define LTC4282_GPIO_ALARM_L_MASK BIT(0) + #define LTC4282_GPIO_ALARM_H_MASK BIT(1) + #define LTC4282_VSOURCE_ALARM_L_MASK BIT(2) + #define LTC4282_VSOURCE_ALARM_H_MASK BIT(3) + #define LTC4282_VSENSE_ALARM_L_MASK BIT(4) + #define LTC4282_VSENSE_ALARM_H_MASK BIT(5) + #define LTC4282_POWER_ALARM_L_MASK BIT(6) + #define LTC4282_POWER_ALARM_H_MASK BIT(7) +#define LTC4282_FET_BAD_FAULT_TIMEOUT 0x06 + #define LTC4282_FET_BAD_MAX_TIMEOUT 255 +#define LTC4282_GPIO_CONFIG 0x07 + #define LTC4282_GPIO_2_FET_STRESS_MASK BIT(1) + #define LTC4282_GPIO_1_CONFIG_MASK GENMASK(5, 4) +#define LTC4282_VGPIO_MIN 0x08 +#define LTC4282_VGPIO_MAX 0x09 +#define LTC4282_VSOURCE_MIN 0x0a +#define LTC4282_VSOURCE_MAX 0x0b +#define LTC4282_VSENSE_MIN 0x0c +#define LTC4282_VSENSE_MAX 0x0d +#define LTC4282_POWER_MIN 0x0e +#define LTC4282_POWER_MAX 0x0f +#define LTC4282_CLK_DIV 0x10 + #define LTC4282_CLK_DIV_MASK GENMASK(4, 0) + #define LTC4282_CLKOUT_MASK GENMASK(6, 5) +#define LTC4282_ILIM_ADJUST 0x11 + #define LTC4282_GPIO_MODE_MASK BIT(1) + #define LTC4282_VDD_MONITOR_MASK BIT(2) + #define LTC4282_FOLDBACK_MODE_MASK GENMASK(4, 3) + #define LTC4282_ILIM_ADJUST_MASK GENMASK(7, 5) +#define LTC4282_ENERGY 0x12 +#define LTC4282_TIME_COUNTER 0x18 +#define LTC4282_ALERT_CTRL 0x1c + #define LTC4282_ALERT_OUT_MASK BIT(6) +#define LTC4282_ADC_CTRL 0x1d + #define LTC4282_FAULT_LOG_EN_MASK BIT(2) + #define LTC4282_METER_HALT_MASK BIT(5) + #define LTC4282_METER_RESET_MASK BIT(6) + #define LTC4282_RESET_MASK BIT(7) +#define LTC4282_STATUS_LSB 0x1e + #define LTC4282_OV_STATUS_MASK BIT(0) + #define LTC4282_UV_STATUS_MASK BIT(1) + #define LTC4282_VDD_STATUS_MASK \ + (LTC4282_OV_STATUS_MASK | LTC4282_UV_STATUS_MASK) + #define LTC4282_OC_STATUS_MASK BIT(2) + #define LTC4282_POWER_GOOD_MASK BIT(3) + #define LTC4282_FET_FAILURE_MASK GENMASK(6, 5) +#define LTC4282_STATUS_MSB 0x1f +#define LTC4282_RESERVED_1 0x32 +#define LTC4282_RESERVED_2 0x33 +#define LTC4282_VGPIO 0x34 +#define LTC4282_VGPIO_LOWEST 0x36 +#define LTC4282_VGPIO_HIGHEST 0x38 +#define LTC4282_VSOURCE 0x3a +#define LTC4282_VSOURCE_LOWEST 0x3c +#define LTC4282_VSOURCE_HIGHEST 0x3e +#define LTC4282_VSENSE 0x40 +#define LTC4282_VSENSE_LOWEST 0x42 +#define LTC4282_VSENSE_HIGHEST 0x44 +#define LTC4282_POWER 0x46 +#define LTC4282_POWER_LOWEST 0x48 +#define LTC4282_POWER_HIGHEST 0x4a +#define LTC4282_RESERVED_3 0x50 + +#define LTC4282_CLKIN_MIN (250 * KILO) +#define LTC4282_CLKIN_MAX (15500 * KILO) +#define LTC4282_CLKIN_RANGE (LTC4282_CLKIN_MAX - LTC4282_CLKIN_MIN + 1) +#define LTC4282_CLKOUT_SYSTEM (250 * KILO) +#define LTC4282_CLKOUT_CNV 15 + +enum { + LTC4282_CHAN_VSOURCE, + LTC4282_CHAN_VDD, + LTC4282_CHAN_VGPIO, +}; + +struct ltc4282_cache { + u32 in_max_raw; + u32 in_min_raw; + long in_highest; + long in_lowest; + bool en; +}; + +struct ltc4282_state { + struct regmap *map; + /* Protect against multiple accesses to the device registers */ + struct mutex lock; + struct clk_hw clk_hw; + /* + * Used to cache values for VDD/VSOURCE depending which will be used + * when hwmon is not enabled for that channel. Needed because they share + * the same registers. + */ + struct ltc4282_cache in0_1_cache[LTC4282_CHAN_VGPIO]; + u32 vsense_max; + long power_max; + u32 rsense; + u16 vdd; + u16 vfs_out; + bool energy_en; +}; + +enum { + LTC4282_CLKOUT_NONE, + LTC4282_CLKOUT_INT, + LTC4282_CLKOUT_TICK, +}; + +static int ltc4282_set_rate(struct clk_hw *hw, + unsigned long rate, unsigned long parent_rate) +{ + struct ltc4282_state *st = container_of(hw, struct ltc4282_state, + clk_hw); + u32 val = LTC4282_CLKOUT_INT; + + if (rate == LTC4282_CLKOUT_CNV) + val = LTC4282_CLKOUT_TICK; + + return regmap_update_bits(st->map, LTC4282_CLK_DIV, LTC4282_CLKOUT_MASK, + FIELD_PREP(LTC4282_CLKOUT_MASK, val)); +} + +/* + * Note the 15HZ conversion rate assumes 12bit ADC which is what we are + * supporting for now. + */ +static const unsigned int ltc4282_out_rates[] = { + LTC4282_CLKOUT_CNV, LTC4282_CLKOUT_SYSTEM +}; + +static long ltc4282_round_rate(struct clk_hw *hw, unsigned long rate, + unsigned long *parent_rate) +{ + int idx = find_closest(rate, ltc4282_out_rates, + ARRAY_SIZE(ltc4282_out_rates)); + + return ltc4282_out_rates[idx]; +} + +static unsigned long ltc4282_recalc_rate(struct clk_hw *hw, + unsigned long parent) +{ + struct ltc4282_state *st = container_of(hw, struct ltc4282_state, + clk_hw); + u32 clkdiv; + int ret; + + ret = regmap_read(st->map, LTC4282_CLK_DIV, &clkdiv); + if (ret) + return 0; + + clkdiv = FIELD_GET(LTC4282_CLKOUT_MASK, clkdiv); + if (!clkdiv) + return 0; + if (clkdiv == LTC4282_CLKOUT_INT) + return LTC4282_CLKOUT_SYSTEM; + + return LTC4282_CLKOUT_CNV; +} + +static void ltc4282_disable(struct clk_hw *clk_hw) +{ + struct ltc4282_state *st = container_of(clk_hw, struct ltc4282_state, + clk_hw); + + regmap_clear_bits(st->map, LTC4282_CLK_DIV, LTC4282_CLKOUT_MASK); +} + +static int ltc4282_read_voltage_word(const struct ltc4282_state *st, u32 reg, + u32 fs, long *val) +{ + __be16 in; + int ret; + + ret = regmap_bulk_read(st->map, reg, &in, sizeof(in)); + if (ret) + return ret; + + /* + * This is also used to calculate current in which case fs comes in + * 10 * uV. Hence the ULL usage. + */ + *val = DIV_ROUND_CLOSEST_ULL(be16_to_cpu(in) * (u64)fs, U16_MAX); + return 0; +} + +static int ltc4282_read_voltage_byte_cached(const struct ltc4282_state *st, + u32 reg, u32 fs, long *val, + u32 *cached_raw) +{ + int ret; + u32 in; + + if (cached_raw) { + in = *cached_raw; + } else { + ret = regmap_read(st->map, reg, &in); + if (ret) + return ret; + } + + *val = DIV_ROUND_CLOSEST(in * fs, U8_MAX); + return 0; +} + +static int ltc4282_read_voltage_byte(const struct ltc4282_state *st, u32 reg, + u32 fs, long *val) +{ + return ltc4282_read_voltage_byte_cached(st, reg, fs, val, NULL); +} + +static int __ltc4282_read_alarm(struct ltc4282_state *st, u32 reg, u32 mask, + long *val) +{ + u32 alarm; + int ret; + + ret = regmap_read(st->map, reg, &alarm); + if (ret) + return ret; + + *val = !!(alarm & mask); + + /* if not status/fault logs, clear the alarm after reading it */ + if (reg != LTC4282_STATUS_LSB && reg != LTC4282_FAULT_LOG) + return regmap_clear_bits(st->map, reg, mask); + + return 0; +} + +static int ltc4282_read_alarm(struct ltc4282_state *st, u32 reg, u32 mask, + long *val) +{ + guard(mutex)(&st->lock); + return __ltc4282_read_alarm(st, reg, mask, val); +} + +static int ltc4282_vdd_source_read_in(struct ltc4282_state *st, u32 channel, + long *val) +{ + guard(mutex)(&st->lock); + if (!st->in0_1_cache[channel].en) + return -ENODATA; + + return ltc4282_read_voltage_word(st, LTC4282_VSOURCE, st->vfs_out, val); +} + +static int ltc4282_vdd_source_read_hist(struct ltc4282_state *st, u32 reg, + u32 channel, long *cached, long *val) +{ + int ret; + + guard(mutex)(&st->lock); + if (!st->in0_1_cache[channel].en) { + *val = *cached; + return 0; + } + + ret = ltc4282_read_voltage_word(st, reg, st->vfs_out, val); + if (ret) + return ret; + + *cached = *val; + return 0; +} + +static int ltc4282_vdd_source_read_lim(struct ltc4282_state *st, u32 reg, + u32 channel, u32 *cached, long *val) +{ + guard(mutex)(&st->lock); + if (!st->in0_1_cache[channel].en) + return ltc4282_read_voltage_byte_cached(st, reg, st->vfs_out, + val, cached); + + return ltc4282_read_voltage_byte(st, reg, st->vfs_out, val); +} + +static int ltc4282_vdd_source_read_alm(struct ltc4282_state *st, u32 mask, + u32 channel, long *val) +{ + guard(mutex)(&st->lock); + if (!st->in0_1_cache[channel].en) { + /* + * Do this otherwise alarms can get confused because we clear + * them after reading them. So, if someone mistakenly reads + * VSOURCE right before VDD (or the other way around), we might + * get no alarm just because it was cleared when reading VSOURCE + * and had no time for a new conversion and thus having the + * alarm again. + */ + *val = 0; + return 0; + } + + return __ltc4282_read_alarm(st, LTC4282_ADC_ALERT_LOG, mask, val); +} + +static int ltc4282_read_in(struct ltc4282_state *st, u32 attr, long *val, + u32 channel) +{ + switch (attr) { + case hwmon_in_input: + if (channel == LTC4282_CHAN_VGPIO) + return ltc4282_read_voltage_word(st, LTC4282_VGPIO, + 1280, val); + + return ltc4282_vdd_source_read_in(st, channel, val); + case hwmon_in_highest: + if (channel == LTC4282_CHAN_VGPIO) + return ltc4282_read_voltage_word(st, + LTC4282_VGPIO_HIGHEST, + 1280, val); + + return ltc4282_vdd_source_read_hist(st, LTC4282_VSOURCE_HIGHEST, + channel, + &st->in0_1_cache[channel].in_highest, val); + case hwmon_in_lowest: + if (channel == LTC4282_CHAN_VGPIO) + return ltc4282_read_voltage_word(st, LTC4282_VGPIO_LOWEST, + 1280, val); + + return ltc4282_vdd_source_read_hist(st, LTC4282_VSOURCE_LOWEST, + channel, + &st->in0_1_cache[channel].in_lowest, val); + case hwmon_in_max_alarm: + if (channel == LTC4282_CHAN_VGPIO) + return ltc4282_read_alarm(st, LTC4282_ADC_ALERT_LOG, + LTC4282_GPIO_ALARM_H_MASK, + val); + + return ltc4282_vdd_source_read_alm(st, + LTC4282_VSOURCE_ALARM_H_MASK, + channel, val); + case hwmon_in_min_alarm: + if (channel == LTC4282_CHAN_VGPIO) + ltc4282_read_alarm(st, LTC4282_ADC_ALERT_LOG, + LTC4282_GPIO_ALARM_L_MASK, val); + + return ltc4282_vdd_source_read_alm(st, + LTC4282_VSOURCE_ALARM_L_MASK, + channel, val); + case hwmon_in_crit_alarm: + return ltc4282_read_alarm(st, LTC4282_STATUS_LSB, + LTC4282_OV_STATUS_MASK, val); + case hwmon_in_lcrit_alarm: + return ltc4282_read_alarm(st, LTC4282_STATUS_LSB, + LTC4282_UV_STATUS_MASK, val); + case hwmon_in_max: + if (channel == LTC4282_CHAN_VGPIO) + return ltc4282_read_voltage_byte(st, LTC4282_VGPIO_MAX, + 1280, val); + + return ltc4282_vdd_source_read_lim(st, LTC4282_VSOURCE_MAX, + channel, + &st->in0_1_cache[channel].in_max_raw, val); + case hwmon_in_min: + if (channel == LTC4282_CHAN_VGPIO) + return ltc4282_read_voltage_byte(st, LTC4282_VGPIO_MIN, + 1280, val); + + return ltc4282_vdd_source_read_lim(st, LTC4282_VSOURCE_MIN, + channel, + &st->in0_1_cache[channel].in_min_raw, val); + case hwmon_in_enable: + scoped_guard(mutex, &st->lock) { + *val = st->in0_1_cache[channel].en; + } + return 0; + case hwmon_in_fault: + /* + * We report failure if we detect either a fer_bad or a + * fet_short in the status register. + */ + return ltc4282_read_alarm(st, LTC4282_STATUS_LSB, + LTC4282_FET_FAILURE_MASK, val); + default: + return -EOPNOTSUPP; + } +} + +static int ltc4282_read_current_word(const struct ltc4282_state *st, u32 reg, + long *val) +{ + long in; + int ret; + + /* + * We pass in full scale in 10 * micro (note that 40 is already + * millivolt) so we have better approximations to calculate current. + */ + ret = ltc4282_read_voltage_word(st, reg, DECA * 40 * MILLI, &in); + if (ret) + return ret; + + *val = DIV_ROUND_CLOSEST(in * MILLI, st->rsense); + + return 0; +} + +static int ltc4282_read_current_byte(const struct ltc4282_state *st, u32 reg, + long *val) +{ + long in; + int ret; + + ret = ltc4282_read_voltage_byte(st, reg, DECA * 40 * MILLI, &in); + if (ret) + return ret; + + *val = DIV_ROUND_CLOSEST(in * MILLI, st->rsense); + + return 0; +} + +static int ltc4282_read_curr(struct ltc4282_state *st, const u32 attr, + long *val) +{ + switch (attr) { + case hwmon_curr_input: + return ltc4282_read_current_word(st, LTC4282_VSENSE, val); + case hwmon_curr_highest: + return ltc4282_read_current_word(st, LTC4282_VSENSE_HIGHEST, + val); + case hwmon_curr_lowest: + return ltc4282_read_current_word(st, LTC4282_VSENSE_LOWEST, + val); + case hwmon_curr_max: + return ltc4282_read_current_byte(st, LTC4282_VSENSE_MAX, val); + case hwmon_curr_min: + return ltc4282_read_current_byte(st, LTC4282_VSENSE_MIN, val); + case hwmon_curr_max_alarm: + return ltc4282_read_alarm(st, LTC4282_ADC_ALERT_LOG, + LTC4282_VSENSE_ALARM_H_MASK, val); + case hwmon_curr_min_alarm: + return ltc4282_read_alarm(st, LTC4282_ADC_ALERT_LOG, + LTC4282_VSENSE_ALARM_L_MASK, val); + case hwmon_curr_crit_alarm: + return ltc4282_read_alarm(st, LTC4282_STATUS_LSB, + LTC4282_OC_STATUS_MASK, val); + default: + return -EOPNOTSUPP; + } +} + +static int ltc4282_read_power_word(const struct ltc4282_state *st, u32 reg, + long *val) +{ + u64 temp = DECA * 40ULL * st->vfs_out * BIT(16), temp_2; + __be16 raw; + u16 power; + int ret; + + ret = regmap_bulk_read(st->map, reg, &raw, sizeof(raw)); + if (ret) + return ret; + + power = be16_to_cpu(raw); + /* + * Power is given by: + * P = CODE(16b) * 0.040 * Vfs(out) * 2^16 / ((2^16 - 1)^2 * Rsense) + */ + if (check_mul_overflow(power * temp, MICRO, &temp_2)) { + temp = DIV_ROUND_CLOSEST_ULL(power * temp, U16_MAX); + *val = DIV64_U64_ROUND_CLOSEST(temp * MICRO, + U16_MAX * (u64)st->rsense); + return 0; + } + + *val = DIV64_U64_ROUND_CLOSEST(temp_2, + st->rsense * int_pow(U16_MAX, 2)); + + return 0; +} + +static int ltc4282_read_power_byte(const struct ltc4282_state *st, u32 reg, + long *val) +{ + u32 power; + u64 temp; + int ret; + + ret = regmap_read(st->map, reg, &power); + if (ret) + return ret; + + temp = power * 40 * DECA * st->vfs_out * BIT_ULL(8); + *val = DIV64_U64_ROUND_CLOSEST(temp * MICRO, + int_pow(U8_MAX, 2) * st->rsense); + + return 0; +} + +static int ltc4282_read_energy(const struct ltc4282_state *st, u64 *val) +{ + u64 temp, energy; + __be64 raw; + int ret; + + ret = regmap_bulk_read(st->map, LTC4282_ENERGY, &raw, 6); + if (ret) + return ret; + + energy = be64_to_cpu(raw) >> 16; + /* + * The formula for energy is given by: + * E = CODE(48b) * 0.040 * Vfs(out) * Tconv * 256 / + * ((2^16 - 1)^2 * Rsense) + * + * Since we only support 12bit ADC, Tconv = 0.065535s. Passing Vfs(out) + * and 0.040 to mV and Tconv to us, we can simplify the formula to: + * E = CODE(48b) * 40 * Vfs(out) * 256 / (U16_MAX * Rsense) + * + * As Rsense can have tenths of micro-ohm resolution, we need to + * multiply by DECA to get microujoule. + */ + if (check_mul_overflow(DECA * st->vfs_out * 40 * BIT(8), energy, &temp)) { + temp = DIV_ROUND_CLOSEST(DECA * st->vfs_out * 40 * BIT(8), U16_MAX); + *val = DIV_ROUND_CLOSEST_ULL(temp * energy, st->rsense); + return 0; + } + + *val = DIV64_U64_ROUND_CLOSEST(temp, U16_MAX * (u64)st->rsense); + + return 0; +} + +static int ltc4282_read_power(struct ltc4282_state *st, const u32 attr, + long *val) +{ + switch (attr) { + case hwmon_power_input: + return ltc4282_read_power_word(st, LTC4282_POWER, val); + case hwmon_power_input_highest: + return ltc4282_read_power_word(st, LTC4282_POWER_HIGHEST, val); + case hwmon_power_input_lowest: + return ltc4282_read_power_word(st, LTC4282_POWER_LOWEST, val); + case hwmon_power_max_alarm: + return ltc4282_read_alarm(st, LTC4282_ADC_ALERT_LOG, + LTC4282_POWER_ALARM_H_MASK, val); + case hwmon_power_min_alarm: + return ltc4282_read_alarm(st, LTC4282_ADC_ALERT_LOG, + LTC4282_POWER_ALARM_L_MASK, val); + case hwmon_power_max: + return ltc4282_read_power_byte(st, LTC4282_POWER_MAX, val); + case hwmon_power_min: + return ltc4282_read_power_byte(st, LTC4282_POWER_MIN, val); + default: + return -EOPNOTSUPP; + } +} + +static int ltc4282_read(struct device *dev, enum hwmon_sensor_types type, + u32 attr, int channel, long *val) +{ + struct ltc4282_state *st = dev_get_drvdata(dev); + + switch (type) { + case hwmon_in: + return ltc4282_read_in(st, attr, val, channel); + case hwmon_curr: + return ltc4282_read_curr(st, attr, val); + case hwmon_power: + return ltc4282_read_power(st, attr, val); + case hwmon_energy: + scoped_guard(mutex, &st->lock) { + *val = st->energy_en; + } + return 0; + default: + return -EOPNOTSUPP; + } +} + +static int ltc4282_write_power_byte(const struct ltc4282_state *st, u32 reg, + long val) +{ + u32 power; + u64 temp; + + if (val > st->power_max) + val = st->power_max; + + temp = val * int_pow(U8_MAX, 2) * st->rsense; + power = DIV64_U64_ROUND_CLOSEST(temp, + MICRO * DECA * 256ULL * st->vfs_out * 40); + + return regmap_write(st->map, reg, power); +} + +static int ltc4282_write_power_word(const struct ltc4282_state *st, u32 reg, + long val) +{ + u64 temp = int_pow(U16_MAX, 2) * st->rsense, temp_2; + __be16 __raw; + u16 code; + + if (check_mul_overflow(temp, val, &temp_2)) { + temp = DIV_ROUND_CLOSEST_ULL(temp, DECA * MICRO); + code = DIV64_U64_ROUND_CLOSEST(temp * val, + 40ULL * BIT(16) * st->vfs_out); + } else { + temp = DECA * MICRO * 40ULL * BIT(16) * st->vfs_out; + code = DIV64_U64_ROUND_CLOSEST(temp_2, temp); + } + + __raw = cpu_to_be16(code); + return regmap_bulk_write(st->map, reg, &__raw, sizeof(__raw)); +} + +static int __ltc4282_in_write_history(const struct ltc4282_state *st, u32 reg, + long lowest, long highest, u32 fs) +{ + __be16 __raw; + u16 tmp; + int ret; + + tmp = DIV_ROUND_CLOSEST(U16_MAX * lowest, fs); + + __raw = cpu_to_be16(tmp); + + ret = regmap_bulk_write(st->map, reg, &__raw, 2); + if (ret) + return ret; + + tmp = DIV_ROUND_CLOSEST(U16_MAX * highest, fs); + + __raw = cpu_to_be16(tmp); + + return regmap_bulk_write(st->map, reg + 2, &__raw, 2); +} + +static int ltc4282_in_write_history(struct ltc4282_state *st, u32 reg, + long lowest, long highest, u32 fs) +{ + guard(mutex)(&st->lock); + return __ltc4282_in_write_history(st, reg, lowest, highest, fs); +} + +static int ltc4282_power_reset_hist(struct ltc4282_state *st) +{ + int ret; + + guard(mutex)(&st->lock); + + ret = ltc4282_write_power_word(st, LTC4282_POWER_LOWEST, + st->power_max); + if (ret) + return ret; + + ret = ltc4282_write_power_word(st, LTC4282_POWER_HIGHEST, 0); + if (ret) + return ret; + + /* now, let's also clear possible power_bad fault logs */ + return regmap_clear_bits(st->map, LTC4282_FAULT_LOG, + LTC4282_POWER_BAD_FAULT_MASK); +} + +static int ltc4282_write_power(struct ltc4282_state *st, u32 attr, + long val) +{ + switch (attr) { + case hwmon_power_max: + return ltc4282_write_power_byte(st, LTC4282_POWER_MAX, val); + case hwmon_power_min: + return ltc4282_write_power_byte(st, LTC4282_POWER_MIN, val); + case hwmon_power_reset_history: + return ltc4282_power_reset_hist(st); + default: + return -EOPNOTSUPP; + } +} + +static int ltc4282_write_voltage_byte_cached(const struct ltc4282_state *st, + u32 reg, u32 fs, long val, + u32 *cache_raw) +{ + u32 in; + + val = clamp_val(val, 0, fs); + in = DIV_ROUND_CLOSEST(val * U8_MAX, fs); + + if (cache_raw) { + *cache_raw = in; + return 0; + } + + return regmap_write(st->map, reg, in); +} + +static int ltc4282_write_voltage_byte(const struct ltc4282_state *st, u32 reg, + u32 fs, long val) +{ + return ltc4282_write_voltage_byte_cached(st, reg, fs, val, NULL); +} + +static int ltc4282_cache_history(struct ltc4282_state *st, u32 channel) +{ + long val; + int ret; + + ret = ltc4282_read_voltage_word(st, LTC4282_VSOURCE_LOWEST, st->vfs_out, + &val); + if (ret) + return ret; + + st->in0_1_cache[channel].in_lowest = val; + + ret = ltc4282_read_voltage_word(st, LTC4282_VSOURCE_HIGHEST, + st->vfs_out, &val); + if (ret) + return ret; + + st->in0_1_cache[channel].in_highest = val; + + ret = regmap_read(st->map, LTC4282_VSOURCE_MIN, + &st->in0_1_cache[channel].in_min_raw); + if (ret) + return ret; + + return regmap_read(st->map, LTC4282_VSOURCE_MAX, + &st->in0_1_cache[channel].in_max_raw); +} + +static int ltc4282_cache_sync(struct ltc4282_state *st, u32 channel) +{ + int ret; + + ret = __ltc4282_in_write_history(st, LTC4282_VSOURCE_LOWEST, + st->in0_1_cache[channel].in_lowest, + st->in0_1_cache[channel].in_highest, + st->vfs_out); + if (ret) + return ret; + + ret = regmap_write(st->map, LTC4282_VSOURCE_MIN, + st->in0_1_cache[channel].in_min_raw); + if (ret) + return ret; + + return regmap_write(st->map, LTC4282_VSOURCE_MAX, + st->in0_1_cache[channel].in_max_raw); +} + +static int ltc4282_vdd_source_write_lim(struct ltc4282_state *st, u32 reg, + int channel, u32 *cache, long val) +{ + int ret; + + guard(mutex)(&st->lock); + if (st->in0_1_cache[channel].en) + ret = ltc4282_write_voltage_byte(st, reg, st->vfs_out, val); + else + ret = ltc4282_write_voltage_byte_cached(st, reg, st->vfs_out, + val, cache); + + return ret; +} + +static int ltc4282_vdd_source_reset_hist(struct ltc4282_state *st, int channel) +{ + long lowest = st->vfs_out; + int ret; + + if (channel == LTC4282_CHAN_VDD) + lowest = st->vdd; + + guard(mutex)(&st->lock); + if (st->in0_1_cache[channel].en) { + ret = __ltc4282_in_write_history(st, LTC4282_VSOURCE_LOWEST, + lowest, 0, st->vfs_out); + if (ret) + return ret; + } + + st->in0_1_cache[channel].in_lowest = lowest; + st->in0_1_cache[channel].in_highest = 0; + + /* + * We are also clearing possible fault logs in reset_history. Clearing + * the logs might be important when the auto retry bits are not enabled + * as the chip only enables the output again after having these logs + * cleared. As some of these logs are related to limits, it makes sense + * to clear them in here. For VDD, we need to clear under/over voltage + * events. For VSOURCE, fet_short and fet_bad... + */ + if (channel == LTC4282_CHAN_VSOURCE) + return regmap_clear_bits(st->map, LTC4282_FAULT_LOG, + LTC4282_FET_FAILURE_FAULT_MASK); + + return regmap_clear_bits(st->map, LTC4282_FAULT_LOG, + LTC4282_VDD_FAULT_MASK); +} + +/* + * We need to mux between VSOURCE and VDD which means they are mutually + * exclusive. Moreover, we can't really disable both VDD and VSOURCE as the ADC + * is continuously running (we cannot independently halt it without also + * stopping VGPIO). Hence, the logic is that disabling or enabling VDD will + * automatically have the reverse effect on VSOURCE and vice-versa. + */ +static int ltc4282_vdd_source_enable(struct ltc4282_state *st, int channel, + long val) +{ + int ret, other_chan = ~channel & 0x1; + u8 __val = val; + + guard(mutex)(&st->lock); + if (st->in0_1_cache[channel].en == !!val) + return 0; + + /* clearing the bit makes the ADC to monitor VDD */ + if (channel == LTC4282_CHAN_VDD) + __val = !__val; + + ret = regmap_update_bits(st->map, LTC4282_ILIM_ADJUST, + LTC4282_VDD_MONITOR_MASK, + FIELD_PREP(LTC4282_VDD_MONITOR_MASK, !!__val)); + if (ret) + return ret; + + st->in0_1_cache[channel].en = !!val; + st->in0_1_cache[other_chan].en = !val; + + if (st->in0_1_cache[channel].en) { + /* + * Then, we are disabling @other_chan. Let's save it's current + * history. + */ + ret = ltc4282_cache_history(st, other_chan); + if (ret) + return ret; + + return ltc4282_cache_sync(st, channel); + } + /* + * Then, we are enabling @other_chan. We need to do the opposite from + * above. + */ + ret = ltc4282_cache_history(st, channel); + if (ret) + return ret; + + return ltc4282_cache_sync(st, other_chan); +} + +static int ltc4282_write_in(struct ltc4282_state *st, u32 attr, long val, + int channel) +{ + switch (attr) { + case hwmon_in_max: + if (channel == LTC4282_CHAN_VGPIO) + return ltc4282_write_voltage_byte(st, LTC4282_VGPIO_MAX, + 1280, val); + + return ltc4282_vdd_source_write_lim(st, LTC4282_VSOURCE_MAX, + channel, + &st->in0_1_cache[channel].in_max_raw, val); + case hwmon_in_min: + if (channel == LTC4282_CHAN_VGPIO) + return ltc4282_write_voltage_byte(st, LTC4282_VGPIO_MIN, + 1280, val); + + return ltc4282_vdd_source_write_lim(st, LTC4282_VSOURCE_MIN, + channel, + &st->in0_1_cache[channel].in_min_raw, val); + case hwmon_in_reset_history: + if (channel == LTC4282_CHAN_VGPIO) + return ltc4282_in_write_history(st, + LTC4282_VGPIO_LOWEST, + 1280, 0, 1280); + + return ltc4282_vdd_source_reset_hist(st, channel); + case hwmon_in_enable: + return ltc4282_vdd_source_enable(st, channel, val); + default: + return -EOPNOTSUPP; + } +} + +static int ltc4282_curr_reset_hist(struct ltc4282_state *st) +{ + int ret; + + guard(mutex)(&st->lock); + + ret = __ltc4282_in_write_history(st, LTC4282_VSENSE_LOWEST, + st->vsense_max, 0, 40 * MILLI); + if (ret) + return ret; + + /* now, let's also clear possible overcurrent fault logs */ + return regmap_clear_bits(st->map, LTC4282_FAULT_LOG, + LTC4282_OC_FAULT_MASK); +} + +static int ltc4282_write_curr(struct ltc4282_state *st, u32 attr, + long val) +{ + /* need to pass it in millivolt */ + u32 in = DIV_ROUND_CLOSEST_ULL((u64)val * st->rsense, DECA * MICRO); + + switch (attr) { + case hwmon_curr_max: + return ltc4282_write_voltage_byte(st, LTC4282_VSENSE_MAX, 40, + in); + case hwmon_curr_min: + return ltc4282_write_voltage_byte(st, LTC4282_VSENSE_MIN, 40, + in); + case hwmon_curr_reset_history: + return ltc4282_curr_reset_hist(st); + default: + return -EOPNOTSUPP; + } +} + +static int ltc4282_energy_enable_set(struct ltc4282_state *st, long val) +{ + int ret; + + guard(mutex)(&st->lock); + /* setting the bit halts the meter */ + ret = regmap_update_bits(st->map, LTC4282_ADC_CTRL, + LTC4282_METER_HALT_MASK, + FIELD_PREP(LTC4282_METER_HALT_MASK, !val)); + if (ret) + return ret; + + st->energy_en = !!val; + + return 0; +} + +static int ltc4282_write(struct device *dev, + enum hwmon_sensor_types type, + u32 attr, int channel, long val) +{ + struct ltc4282_state *st = dev_get_drvdata(dev); + + switch (type) { + case hwmon_power: + return ltc4282_write_power(st, attr, val); + case hwmon_in: + return ltc4282_write_in(st, attr, val, channel); + case hwmon_curr: + return ltc4282_write_curr(st, attr, val); + case hwmon_energy: + return ltc4282_energy_enable_set(st, val); + default: + return -EOPNOTSUPP; + } +} + +static umode_t ltc4282_in_is_visible(const struct ltc4282_state *st, u32 attr) +{ + switch (attr) { + case hwmon_in_input: + case hwmon_in_highest: + case hwmon_in_lowest: + case hwmon_in_max_alarm: + case hwmon_in_min_alarm: + case hwmon_in_label: + case hwmon_in_lcrit_alarm: + case hwmon_in_crit_alarm: + case hwmon_in_fault: + return 0444; + case hwmon_in_max: + case hwmon_in_min: + case hwmon_in_enable: + case hwmon_in_reset_history: + return 0644; + default: + return 0; + } +} + +static umode_t ltc4282_curr_is_visible(u32 attr) +{ + switch (attr) { + case hwmon_curr_input: + case hwmon_curr_highest: + case hwmon_curr_lowest: + case hwmon_curr_max_alarm: + case hwmon_curr_min_alarm: + case hwmon_curr_crit_alarm: + case hwmon_curr_label: + return 0444; + case hwmon_curr_max: + case hwmon_curr_min: + case hwmon_curr_reset_history: + return 0644; + default: + return 0; + } +} + +static umode_t ltc4282_power_is_visible(u32 attr) +{ + switch (attr) { + case hwmon_power_input: + case hwmon_power_input_highest: + case hwmon_power_input_lowest: + case hwmon_power_label: + case hwmon_power_max_alarm: + case hwmon_power_min_alarm: + return 0444; + case hwmon_power_max: + case hwmon_power_min: + case hwmon_power_reset_history: + return 0644; + default: + return 0; + } +} + +static umode_t ltc4282_is_visible(const void *data, + enum hwmon_sensor_types type, + u32 attr, int channel) +{ + switch (type) { + case hwmon_in: + return ltc4282_in_is_visible(data, attr); + case hwmon_curr: + return ltc4282_curr_is_visible(attr); + case hwmon_power: + return ltc4282_power_is_visible(attr); + case hwmon_energy: + /* hwmon_energy_enable */ + return 0644; + default: + return 0; + } +} + +static const char * const ltc4282_in_strs[] = { + "VSOURCE", "VDD", "VGPIO" +}; + +static int ltc4282_read_labels(struct device *dev, + enum hwmon_sensor_types type, + u32 attr, int channel, const char **str) +{ + switch (type) { + case hwmon_in: + *str = ltc4282_in_strs[channel]; + return 0; + case hwmon_curr: + *str = "ISENSE"; + return 0; + case hwmon_power: + *str = "Power"; + return 0; + default: + return -EOPNOTSUPP; + } +} + +static ssize_t ltc4282_energy_show(struct device *dev, + struct device_attribute *da, char *buf) +{ + struct ltc4282_state *st = dev_get_drvdata(dev); + u64 energy; + int ret; + + guard(mutex)(&st->lock); + if (!st->energy_en) + return -ENODATA; + + ret = ltc4282_read_energy(st, &energy); + if (ret < 0) + return ret; + + return sysfs_emit(buf, "%llu\n", energy); +} + +static const struct clk_ops ltc4282_ops = { + .recalc_rate = ltc4282_recalc_rate, + .round_rate = ltc4282_round_rate, + .set_rate = ltc4282_set_rate, + .disable = ltc4282_disable, +}; + +static int ltc428_clk_provider_setup(struct ltc4282_state *st, + struct device *dev) +{ + struct clk_init_data init; + int ret; + + if (!IS_ENABLED(CONFIG_COMMON_CLK)) + return 0; + + init.name = devm_kasprintf(dev, GFP_KERNEL, "%s-clk", + fwnode_get_name(dev_fwnode(dev))); + if (!init.name) + return -ENOMEM; + + init.ops = <c4282_ops; + init.flags = CLK_GET_RATE_NOCACHE; + st->clk_hw.init = &init; + + ret = devm_clk_hw_register(dev, &st->clk_hw); + if (ret) + return ret; + + return devm_of_clk_add_hw_provider(dev, of_clk_hw_simple_get, + &st->clk_hw); +} + +static int ltc428_clks_setup(struct ltc4282_state *st, struct device *dev) +{ + unsigned long rate; + struct clk *clkin; + u32 val; + int ret; + + ret = ltc428_clk_provider_setup(st, dev); + if (ret) + return ret; + + clkin = devm_clk_get_optional_enabled(dev, NULL); + if (IS_ERR(clkin)) + return dev_err_probe(dev, PTR_ERR(clkin), + "Failed to get clkin"); + if (!clkin) + return 0; + + rate = clk_get_rate(clkin); + if (!in_range(rate, LTC4282_CLKIN_MIN, LTC4282_CLKIN_RANGE)) + return dev_err_probe(dev, -EINVAL, + "Invalid clkin range(%lu) [%lu %lu]\n", + rate, LTC4282_CLKIN_MIN, + LTC4282_CLKIN_MAX); + + /* + * Clocks faster than 250KHZ should be reduced to 250KHZ. The clock + * frequency is divided by twice the value in the register. + */ + val = rate / (2 * LTC4282_CLKIN_MIN); + + return regmap_update_bits(st->map, LTC4282_CLK_DIV, + LTC4282_CLK_DIV_MASK, + FIELD_PREP(LTC4282_CLK_DIV_MASK, val)); +} + +static const int ltc4282_curr_lim_uv[] = { + 12500, 15625, 18750, 21875, 25000, 28125, 31250, 34375 +}; + +static int ltc4282_get_defaults(struct ltc4282_state *st, u32 *vin_mode) +{ + u32 reg_val, ilm_adjust; + int ret; + + ret = regmap_read(st->map, LTC4282_ADC_CTRL, ®_val); + if (ret) + return ret; + + st->energy_en = !FIELD_GET(LTC4282_METER_HALT_MASK, reg_val); + + ret = regmap_read(st->map, LTC4282_CTRL_MSB, ®_val); + if (ret) + return ret; + + *vin_mode = FIELD_GET(LTC4282_CTRL_VIN_MODE_MASK, reg_val); + + ret = regmap_read(st->map, LTC4282_ILIM_ADJUST, ®_val); + if (ret) + return ret; + + ilm_adjust = FIELD_GET(LTC4282_ILIM_ADJUST_MASK, reg_val); + st->vsense_max = ltc4282_curr_lim_uv[ilm_adjust]; + + st->in0_1_cache[LTC4282_CHAN_VSOURCE].en = FIELD_GET(LTC4282_VDD_MONITOR_MASK, + ilm_adjust); + if (!st->in0_1_cache[LTC4282_CHAN_VSOURCE].en) { + st->in0_1_cache[LTC4282_CHAN_VDD].en = true; + return regmap_read(st->map, LTC4282_VSOURCE_MAX, + &st->in0_1_cache[LTC4282_CHAN_VSOURCE].in_max_raw); + } + + return regmap_read(st->map, LTC4282_VSOURCE_MAX, + &st->in0_1_cache[LTC4282_CHAN_VDD].in_max_raw); +} + +/* + * Set max limits for ISENSE and Power as that depends on the max voltage on + * rsense that is defined in ILIM_ADJUST. This is specially important for power + * because for some rsense and vfsout values, if we allow the default raw 255 + * value, that would overflow long in 32bit archs when reading back the max + * power limit. + * + * Also set meaningful historic values for VDD and VSOURCE + * (0 would not mean much). + */ +static int ltc4282_set_max_limits(struct ltc4282_state *st) +{ + int ret; + + ret = ltc4282_write_voltage_byte(st, LTC4282_VSENSE_MAX, 40 * MILLI, + st->vsense_max); + if (ret) + return ret; + + /* Power is given by ISENSE * Vout. */ + st->power_max = DIV_ROUND_CLOSEST(st->vsense_max * DECA * MILLI, st->rsense) * st->vfs_out; + ret = ltc4282_write_power_byte(st, LTC4282_POWER_MAX, st->power_max); + if (ret) + return ret; + + if (st->in0_1_cache[LTC4282_CHAN_VDD].en) { + st->in0_1_cache[LTC4282_CHAN_VSOURCE].in_lowest = st->vfs_out; + return __ltc4282_in_write_history(st, LTC4282_VSOURCE_LOWEST, + st->vdd, 0, st->vfs_out); + } + + st->in0_1_cache[LTC4282_CHAN_VDD].in_lowest = st->vdd; + return __ltc4282_in_write_history(st, LTC4282_VSOURCE_LOWEST, + st->vfs_out, 0, st->vfs_out); +} + +static const char * const ltc4282_gpio1_modes[] = { + "power_bad", "power_good" +}; + +static const char * const ltc4282_gpio2_modes[] = { + "adc_input", "stress_fet" +}; + +static int ltc4282_gpio_setup(struct ltc4282_state *st, struct device *dev) +{ + const char *func = NULL; + int ret; + + ret = device_property_read_string(dev, "adi,gpio1-mode", &func); + if (!ret) { + ret = match_string(ltc4282_gpio1_modes, + ARRAY_SIZE(ltc4282_gpio1_modes), func); + if (ret < 0) + return dev_err_probe(dev, ret, + "Invalid func(%s) for gpio1\n", + func); + + ret = regmap_update_bits(st->map, LTC4282_GPIO_CONFIG, + LTC4282_GPIO_1_CONFIG_MASK, + FIELD_PREP(LTC4282_GPIO_1_CONFIG_MASK, ret)); + if (ret) + return ret; + } + + ret = device_property_read_string(dev, "adi,gpio2-mode", &func); + if (!ret) { + ret = match_string(ltc4282_gpio2_modes, + ARRAY_SIZE(ltc4282_gpio2_modes), func); + if (ret < 0) + return dev_err_probe(dev, ret, + "Invalid func(%s) for gpio2\n", + func); + if (!ret) { + /* setting the bit to 1 so the ADC to monitors GPIO2 */ + ret = regmap_set_bits(st->map, LTC4282_ILIM_ADJUST, + LTC4282_GPIO_MODE_MASK); + } else { + ret = regmap_update_bits(st->map, LTC4282_GPIO_CONFIG, + LTC4282_GPIO_2_FET_STRESS_MASK, + FIELD_PREP(LTC4282_GPIO_2_FET_STRESS_MASK, 1)); + } + + if (ret) + return ret; + } + + if (!device_property_read_bool(dev, "adi,gpio3-monitor-enable")) + return 0; + + if (func && !strcmp(func, "adc_input")) + return dev_err_probe(dev, -EINVAL, + "Cannot have both gpio2 and gpio3 muxed into the ADC"); + + return regmap_clear_bits(st->map, LTC4282_ILIM_ADJUST, + LTC4282_GPIO_MODE_MASK); +} + +static const char * const ltc4282_dividers[] = { + "external", "vdd_5_percent", "vdd_10_percent", "vdd_15_percent" +}; + +/* This maps the Vout full scale for the given Vin mode */ +static const u16 ltc4282_vfs_milli[] = { 5540, 8320, 16640, 33280 }; + +static const u16 ltc4282_vdd_milli[] = { 3300, 5000, 12000, 24000 }; + +enum { + LTC4282_VIN_3_3V, + LTC4282_VIN_5V, + LTC4282_VIN_12V, + LTC4282_VIN_24V, +}; + +static int ltc4282_setup(struct ltc4282_state *st, struct device *dev) +{ + const char *divider; + u32 val, vin_mode; + int ret; + + /* The part has an eeprom so let's get the needed defaults from it */ + ret = ltc4282_get_defaults(st, &vin_mode); + if (ret) + return ret; + + ret = device_property_read_u32(dev, "adi,rsense-nano-ohms", + &st->rsense); + if (ret) + return dev_err_probe(dev, ret, + "Failed to read adi,rsense-nano-ohms\n"); + if (st->rsense < CENTI) + return dev_err_probe(dev, -EINVAL, + "adi,rsense-nano-ohms too small (< %lu)\n", + CENTI); + + /* + * The resolution for rsense is tenths of micro (eg: 62.5 uOhm) which + * means we need nano in the bindings. However, to make things easier to + * handle (with respect to overflows) we divide it by 100 as we don't + * really need the last two digits. + */ + st->rsense /= CENTI; + + val = vin_mode; + ret = device_property_read_u32(dev, "adi,vin-mode-microvolt", &val); + if (!ret) { + switch (val) { + case 3300000: + val = LTC4282_VIN_3_3V; + break; + case 5000000: + val = LTC4282_VIN_5V; + break; + case 12000000: + val = LTC4282_VIN_12V; + break; + case 24000000: + val = LTC4282_VIN_24V; + break; + default: + return dev_err_probe(dev, -EINVAL, + "Invalid val(%u) for vin-mode-microvolt\n", + val); + } + + ret = regmap_update_bits(st->map, LTC4282_CTRL_MSB, + LTC4282_CTRL_VIN_MODE_MASK, + FIELD_PREP(LTC4282_CTRL_VIN_MODE_MASK, val)); + if (ret) + return ret; + + /* Foldback mode should also be set to the input voltage */ + ret = regmap_update_bits(st->map, LTC4282_ILIM_ADJUST, + LTC4282_FOLDBACK_MODE_MASK, + FIELD_PREP(LTC4282_FOLDBACK_MODE_MASK, val)); + if (ret) + return ret; + } + + st->vfs_out = ltc4282_vfs_milli[val]; + st->vdd = ltc4282_vdd_milli[val]; + + ret = device_property_read_u32(dev, "adi,current-limit-sense-microvolt", + &st->vsense_max); + if (!ret) { + int reg_val; + + switch (val) { + case 12500: + reg_val = 0; + break; + case 15625: + reg_val = 1; + break; + case 18750: + reg_val = 2; + break; + case 21875: + reg_val = 3; + break; + case 25000: + reg_val = 4; + break; + case 28125: + reg_val = 5; + break; + case 31250: + reg_val = 6; + break; + case 34375: + reg_val = 7; + break; + default: + return dev_err_probe(dev, -EINVAL, + "Invalid val(%u) for adi,current-limit-microvolt\n", + st->vsense_max); + } + + ret = regmap_update_bits(st->map, LTC4282_ILIM_ADJUST, + LTC4282_ILIM_ADJUST_MASK, + FIELD_PREP(LTC4282_ILIM_ADJUST_MASK, reg_val)); + if (ret) + return ret; + } + + ret = ltc4282_set_max_limits(st); + if (ret) + return ret; + + ret = device_property_read_string(dev, "adi,overvoltage-dividers", + ÷r); + if (!ret) { + int div = match_string(ltc4282_dividers, + ARRAY_SIZE(ltc4282_dividers), divider); + if (div < 0) + return dev_err_probe(dev, -EINVAL, + "Invalid val(%s) for adi,overvoltage-divider\n", + divider); + + ret = regmap_update_bits(st->map, LTC4282_CTRL_MSB, + LTC4282_CTRL_OV_MODE_MASK, + FIELD_PREP(LTC4282_CTRL_OV_MODE_MASK, div)); + } + + ret = device_property_read_string(dev, "adi,undervoltage-dividers", + ÷r); + if (!ret) { + int div = match_string(ltc4282_dividers, + ARRAY_SIZE(ltc4282_dividers), divider); + if (div < 0) + return dev_err_probe(dev, -EINVAL, + "Invalid val(%s) for adi,undervoltage-divider\n", + divider); + + ret = regmap_update_bits(st->map, LTC4282_CTRL_MSB, + LTC4282_CTRL_UV_MODE_MASK, + FIELD_PREP(LTC4282_CTRL_UV_MODE_MASK, div)); + } + + if (device_property_read_bool(dev, "adi,overcurrent-retry")) { + ret = regmap_set_bits(st->map, LTC4282_CTRL_LSB, + LTC4282_CTRL_OC_RETRY_MASK); + if (ret) + return ret; + } + + if (device_property_read_bool(dev, "adi,overvoltage-retry-disable")) { + ret = regmap_clear_bits(st->map, LTC4282_CTRL_LSB, + LTC4282_CTRL_OV_RETRY_MASK); + if (ret) + return ret; + } + + if (device_property_read_bool(dev, "adi,undervoltage-retry-disable")) { + ret = regmap_clear_bits(st->map, LTC4282_CTRL_LSB, + LTC4282_CTRL_UV_RETRY_MASK); + if (ret) + return ret; + } + + if (device_property_read_bool(dev, "adi,fault-log-enable")) { + ret = regmap_set_bits(st->map, LTC4282_ADC_CTRL, + LTC4282_FAULT_LOG_EN_MASK); + if (ret) + return ret; + } + + if (device_property_read_bool(dev, "adi,fault-log-enable")) { + ret = regmap_set_bits(st->map, LTC4282_ADC_CTRL, LTC4282_FAULT_LOG_EN_MASK); + if (ret) + return ret; + } + + ret = device_property_read_u32(dev, "adi,fet-bad-timeout-ms", &val); + if (!ret) { + if (val > LTC4282_FET_BAD_MAX_TIMEOUT) + return dev_err_probe(dev, -EINVAL, + "Invalid value(%u) for adi,fet-bad-timeout-ms", + val); + + ret = regmap_write(st->map, LTC4282_FET_BAD_FAULT_TIMEOUT, val); + if (ret) + return ret; + } + + return ltc4282_gpio_setup(st, dev); +} + +static bool ltc4282_readable_reg(struct device *dev, unsigned int reg) +{ + if (reg == LTC4282_RESERVED_1 || reg == LTC4282_RESERVED_2) + return false; + + return true; +} + +static bool ltc4282_writable_reg(struct device *dev, unsigned int reg) +{ + if (reg == LTC4282_STATUS_LSB || reg == LTC4282_STATUS_MSB) + return false; + if (reg == LTC4282_RESERVED_1 || reg == LTC4282_RESERVED_2) + return false; + + return true; +} + +static const struct regmap_config ltc4282_regmap_config = { + .reg_bits = 8, + .val_bits = 8, + .max_register = LTC4282_RESERVED_3, + .readable_reg = ltc4282_readable_reg, + .writeable_reg = ltc4282_writable_reg, +}; + +static const struct hwmon_channel_info * const ltc4282_info[] = { + HWMON_CHANNEL_INFO(in, + HWMON_I_INPUT | HWMON_I_LOWEST | HWMON_I_HIGHEST | + HWMON_I_MAX | HWMON_I_MIN | HWMON_I_MIN_ALARM | + HWMON_I_MAX_ALARM | HWMON_I_ENABLE | + HWMON_I_RESET_HISTORY | HWMON_I_FAULT | + HWMON_I_LABEL, + HWMON_I_INPUT | HWMON_I_LOWEST | HWMON_I_HIGHEST | + HWMON_I_MAX | HWMON_I_MIN | HWMON_I_MIN_ALARM | + HWMON_I_MAX_ALARM | HWMON_I_LCRIT_ALARM | + HWMON_I_CRIT_ALARM | HWMON_I_ENABLE | + HWMON_I_RESET_HISTORY | HWMON_I_LABEL, + HWMON_I_INPUT | HWMON_I_LOWEST | HWMON_I_HIGHEST | + HWMON_I_MAX | HWMON_I_MIN | HWMON_I_MIN_ALARM | + HWMON_I_RESET_HISTORY | HWMON_I_MAX_ALARM | + HWMON_I_LABEL), + HWMON_CHANNEL_INFO(curr, + HWMON_C_INPUT | HWMON_C_LOWEST | HWMON_C_HIGHEST | + HWMON_C_MAX | HWMON_C_MIN | HWMON_C_MIN_ALARM | + HWMON_C_MAX_ALARM | HWMON_C_CRIT_ALARM | + HWMON_C_RESET_HISTORY | HWMON_C_LABEL), + HWMON_CHANNEL_INFO(power, + HWMON_P_INPUT | HWMON_P_INPUT_LOWEST | + HWMON_P_INPUT_HIGHEST | HWMON_P_MAX | HWMON_P_MIN | + HWMON_P_MAX_ALARM | HWMON_P_MIN_ALARM | + HWMON_P_RESET_HISTORY | HWMON_P_LABEL), + HWMON_CHANNEL_INFO(energy, + HWMON_E_ENABLE), + NULL +}; + +static const struct hwmon_ops ltc4282_hwmon_ops = { + .read = ltc4282_read, + .write = ltc4282_write, + .is_visible = ltc4282_is_visible, + .read_string = ltc4282_read_labels, +}; + +static const struct hwmon_chip_info ltc2947_chip_info = { + .ops = <c4282_hwmon_ops, + .info = ltc4282_info, +}; + +/* energy attributes are 6bytes wide so we need u64 */ +static SENSOR_DEVICE_ATTR_RO(energy1_input, ltc4282_energy, 0); + +static struct attribute *ltc4282_attrs[] = { + &sensor_dev_attr_energy1_input.dev_attr.attr, + NULL +}; +ATTRIBUTE_GROUPS(ltc4282); + +static int ltc4282_show_fault_log(void *arg, u64 *val, u32 mask) +{ + struct ltc4282_state *st = arg; + long alarm; + int ret; + + ret = ltc4282_read_alarm(st, LTC4282_FAULT_LOG, mask, &alarm); + if (ret) + return ret; + + *val = alarm; + + return 0; +} + +static int ltc4282_show_curr1_crit_fault_log(void *arg, u64 *val) +{ + return ltc4282_show_fault_log(arg, val, LTC4282_OC_FAULT_MASK); +} +DEFINE_DEBUGFS_ATTRIBUTE(ltc4282_curr1_crit_fault_log, + ltc4282_show_curr1_crit_fault_log, NULL, "%llu\n"); + +static int ltc4282_show_in1_lcrit_fault_log(void *arg, u64 *val) +{ + return ltc4282_show_fault_log(arg, val, LTC4282_UV_FAULT_MASK); +} +DEFINE_DEBUGFS_ATTRIBUTE(ltc4282_in1_lcrit_fault_log, + ltc4282_show_in1_lcrit_fault_log, NULL, "%llu\n"); + +static int ltc4282_show_in1_crit_fault_log(void *arg, u64 *val) +{ + return ltc4282_show_fault_log(arg, val, LTC4282_OV_FAULT_MASK); +} +DEFINE_DEBUGFS_ATTRIBUTE(ltc4282_in1_crit_fault_log, + ltc4282_show_in1_crit_fault_log, NULL, "%llu\n"); + +static int ltc4282_show_fet_bad_fault_log(void *arg, u64 *val) +{ + return ltc4282_show_fault_log(arg, val, LTC4282_FET_BAD_FAULT_MASK); +} +DEFINE_DEBUGFS_ATTRIBUTE(ltc4282_fet_bad_fault_log, + ltc4282_show_fet_bad_fault_log, NULL, "%llu\n"); + +static int ltc4282_show_fet_short_fault_log(void *arg, u64 *val) +{ + return ltc4282_show_fault_log(arg, val, LTC4282_FET_SHORT_FAULT_MASK); +} +DEFINE_DEBUGFS_ATTRIBUTE(ltc4282_fet_short_fault_log, + ltc4282_show_fet_short_fault_log, NULL, "%llu\n"); + +static int ltc4282_show_power1_bad_fault_log(void *arg, u64 *val) +{ + return ltc4282_show_fault_log(arg, val, LTC4282_POWER_BAD_FAULT_MASK); +} +DEFINE_DEBUGFS_ATTRIBUTE(ltc4282_power1_bad_fault_log, + ltc4282_show_power1_bad_fault_log, NULL, "%llu\n"); + +static void ltc4282_debugfs_remove(void *dir) +{ + debugfs_remove_recursive(dir); +} + +static void ltc4282_debugfs_init(struct ltc4282_state *st, + struct i2c_client *i2c, + const struct device *hwmon) +{ + const char *debugfs_name; + struct dentry *dentry; + int ret; + + if (!IS_ENABLED(CONFIG_DEBUG_FS)) + return; + + debugfs_name = devm_kasprintf(&i2c->dev, GFP_KERNEL, "ltc4282-%s", + dev_name(hwmon)); + if (!debugfs_name) + return; + + dentry = debugfs_create_dir(debugfs_name, NULL); + if (IS_ERR(dentry)) + return; + + ret = devm_add_action_or_reset(&i2c->dev, ltc4282_debugfs_remove, + dentry); + if (ret) + return; + + debugfs_create_file_unsafe("power1_bad_fault_log", 0400, dentry, st, + <c4282_power1_bad_fault_log); + debugfs_create_file_unsafe("in0_fet_short_fault_log", 0400, dentry, st, + <c4282_fet_short_fault_log); + debugfs_create_file_unsafe("in0_fet_bad_fault_log", 0400, dentry, st, + <c4282_fet_bad_fault_log); + debugfs_create_file_unsafe("in1_crit_fault_log", 0400, dentry, st, + <c4282_in1_crit_fault_log); + debugfs_create_file_unsafe("in1_lcrit_fault_log", 0400, dentry, st, + <c4282_in1_lcrit_fault_log); + debugfs_create_file_unsafe("curr1_crit_fault_log", 0400, dentry, st, + <c4282_curr1_crit_fault_log); +} + +static int ltc4282_probe(struct i2c_client *i2c) +{ + struct device *dev = &i2c->dev, *hwmon; + struct ltc4282_state *st; + int ret; + + st = devm_kzalloc(dev, sizeof(*st), GFP_KERNEL); + if (!st) + return dev_err_probe(dev, -ENOMEM, + "Failed to allocate memory\n"); + + st->map = devm_regmap_init_i2c(i2c, <c4282_regmap_config); + if (IS_ERR(st->map)) + return dev_err_probe(dev, PTR_ERR(st->map), + "failed regmap init\n"); + + /* Soft reset */ + ret = regmap_set_bits(st->map, LTC4282_ADC_CTRL, LTC4282_RESET_MASK); + if (ret) + return ret; + + /* Yes, it's big but it is as specified in the datasheet */ + msleep(3200); + + ret = ltc428_clks_setup(st, dev); + if (ret) + return ret; + + ret = ltc4282_setup(st, dev); + if (ret) + return ret; + + mutex_init(&st->lock); + hwmon = devm_hwmon_device_register_with_info(dev, "ltc4282", st, + <c2947_chip_info, + ltc4282_groups); + if (IS_ERR(hwmon)) + return PTR_ERR(hwmon); + + ltc4282_debugfs_init(st, i2c, hwmon); + + return 0; +} + +static const struct of_device_id ltc4282_of_match[] = { + { .compatible = "adi,ltc4282" }, + {} +}; +MODULE_DEVICE_TABLE(of, ltc4282_of_match); + +static struct i2c_driver ltc4282_driver = { + .driver = { + .name = "ltc4282", + .of_match_table = ltc4282_of_match, + }, + .probe = ltc4282_probe, +}; +module_i2c_driver(ltc4282_driver); + +MODULE_AUTHOR("Nuno Sa <nuno.sa@analog.com>"); +MODULE_DESCRIPTION("LTC4282 I2C High Current Hot Swap Controller"); +MODULE_LICENSE("GPL"); |