1 files changed, 0 insertions, 138 deletions
diff --git a/Documentation/devicetree/bindings/clock/st,stm32-rcc.txt b/Documentation/devicetree/bindings/clock/st,stm32-rcc.txt
deleted file mode 100644
index cfa04b614d8a..000000000000
--- a/Documentation/devicetree/bindings/clock/st,stm32-rcc.txt
+++ /dev/null
@@ -1,138 +0,0 @@
-STMicroelectronics STM32 Reset and Clock Controller
-===================================================
-
-The RCC IP is both a reset and a clock controller.
-
-Please refer to clock-bindings.txt for common clock controller binding usage.
-Please also refer to reset.txt for common reset controller binding usage.
-
-Required properties:
-- compatible: Should be:
-  "st,stm32f42xx-rcc"
-  "st,stm32f469-rcc"
-  "st,stm32f746-rcc"
-  "st,stm32f769-rcc"
-
-- reg: should be register base and length as documented in the
-  datasheet
-- #reset-cells: 1, see below
-- #clock-cells: 2, device nodes should specify the clock in their "clocks"
-  property, containing a phandle to the clock device node, an index selecting
-  between gated clocks and other clocks and an index specifying the clock to
-  use.
-- clocks: External oscillator clock phandle
-  - high speed external clock signal (HSE)
-  - external I2S clock (I2S_CKIN)
-
-Example:
-
-	rcc: rcc@40023800 {
-		#reset-cells = <1>;
-		#clock-cells = <2>
-		compatible = "st,stm32f42xx-rcc", "st,stm32-rcc";
-		reg = <0x40023800 0x400>;
-		clocks = <&clk_hse>, <&clk_i2s_ckin>;
-	};
-
-Specifying gated clocks
-=======================
-
-The primary index must be set to 0.
-
-The secondary index is the bit number within the RCC register bank, starting
-from the first RCC clock enable register (RCC_AHB1ENR, address offset 0x30).
-
-It is calculated as: index = register_offset / 4 * 32 + bit_offset.
-Where bit_offset is the bit offset within the register (LSB is 0, MSB is 31).
-
-To simplify the usage and to share bit definition with the reset and clock
-drivers of the RCC IP, macros are available to generate the index in
-human-readble format.
-
-For STM32F4 series, the macro are available here:
- - include/dt-bindings/mfd/stm32f4-rcc.h
-
-Example:
-
-	/* Gated clock, AHB1 bit 0 (GPIOA) */
-	... {
-		clocks = <&rcc 0 STM32F4_AHB1_CLOCK(GPIOA)>
-	};
-
-	/* Gated clock, AHB2 bit 4 (CRYP) */
-	... {
-		clocks = <&rcc 0 STM32F4_AHB2_CLOCK(CRYP)>
-	};
-
-Specifying other clocks
-=======================
-
-The primary index must be set to 1.
-
-The secondary index is bound with the following magic numbers:
-
-	0	SYSTICK
-	1	FCLK
-	2	CLK_LSI		(low-power clock source)
-	3	CLK_LSE		(generated from a 32.768 kHz low-speed external
-				 crystal or ceramic resonator)
-	4	CLK_HSE_RTC	(HSE division factor for RTC clock)
-	5	CLK_RTC		(real-time clock)
-	6	PLL_VCO_I2S	(vco frequency of I2S pll)
-	7	PLL_VCO_SAI	(vco frequency of SAI pll)
-	8	CLK_LCD		(LCD-TFT)
-	9	CLK_I2S		(I2S clocks)
-	10	CLK_SAI1	(audio clocks)
-	11	CLK_SAI2
-	12	CLK_I2SQ_PDIV	(post divisor of pll i2s q divisor)
-	13	CLK_SAIQ_PDIV	(post divisor of pll sai q divisor)
-
-	14	CLK_HSI		(Internal ocscillator clock)
-	15	CLK_SYSCLK	(System Clock)
-	16	CLK_HDMI_CEC	(HDMI-CEC clock)
-	17	CLK_SPDIF	(SPDIF-Rx clock)
-	18	CLK_USART1	(U(s)arts clocks)
-	19	CLK_USART2
-	20	CLK_USART3
-	21	CLK_UART4
-	22	CLK_UART5
-	23	CLK_USART6
-	24	CLK_UART7
-	25	CLK_UART8
-	26	CLK_I2C1	(I2S clocks)
-	27	CLK_I2C2
-	28	CLK_I2C3
-	29	CLK_I2C4
-	30	CLK_LPTIMER	(LPTimer1 clock)
-	31	CLK_PLL_SRC
-	32	CLK_DFSDM1
-	33	CLK_ADFSDM1
-	34	CLK_F769_DSI
-)
-
-Example:
-
-	/* Misc clock, FCLK */
-	... {
-		clocks = <&rcc 1 STM32F4_APB1_CLOCK(TIM2)>
-	};
-
-
-Specifying softreset control of devices
-=======================================
-
-Device nodes should specify the reset channel required in their "resets"
-property, containing a phandle to the reset device node and an index specifying
-which channel to use.
-The index is the bit number within the RCC registers bank, starting from RCC
-base address.
-It is calculated as: index = register_offset / 4 * 32 + bit_offset.
-Where bit_offset is the bit offset within the register.
-For example, for CRC reset:
-  crc = AHB1RSTR_offset / 4 * 32 + CRCRST_bit_offset = 0x10 / 4 * 32 + 12 = 140
-
-example:
-
-	timer2 {
-		resets	= <&rcc STM32F4_APB1_RESET(TIM2)>;
-	};