diff options
Diffstat (limited to 'Documentation/devicetree/bindings/hwmon/ti,ina2xx.yaml')
| -rw-r--r-- | Documentation/devicetree/bindings/hwmon/ti,ina2xx.yaml | 46 |
1 files changed, 45 insertions, 1 deletions
diff --git a/Documentation/devicetree/bindings/hwmon/ti,ina2xx.yaml b/Documentation/devicetree/bindings/hwmon/ti,ina2xx.yaml index df86c2c92037..d1fb7b9abda0 100644 --- a/Documentation/devicetree/bindings/hwmon/ti,ina2xx.yaml +++ b/Documentation/devicetree/bindings/hwmon/ti,ina2xx.yaml @@ -1,7 +1,6 @@ # SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause) %YAML 1.2 --- - $id: http://devicetree.org/schemas/hwmon/ti,ina2xx.yaml# $schema: http://devicetree.org/meta-schemas/core.yaml# @@ -20,12 +19,15 @@ description: | properties: compatible: enum: + - silergy,sq52206 + - silergy,sy24655 - ti,ina209 - ti,ina219 - ti,ina220 - ti,ina226 - ti,ina230 - ti,ina231 + - ti,ina233 - ti,ina237 - ti,ina238 - ti,ina260 @@ -57,6 +59,9 @@ properties: shunt voltage, and a value of 4 maps to ADCRANGE=0 such that a wider voltage range is used. + For SQ52206,the shunt-gain value 1 mapps to ADCRANGE=10/11, the value 2 + mapps to ADCRANGE=01, and the value 4 mapps to ADCRANGE=00. + The default value is device dependent, and is defined by the reset value of PGA/ADCRANGE in the respective configuration registers. $ref: /schemas/types.yaml#/definitions/uint32 @@ -66,12 +71,50 @@ properties: description: phandle to the regulator that provides the VS supply typically in range from 2.7 V to 5.5 V. + ti,alert-polarity-active-high: + description: Alert pin is asserted based on the value of Alert polarity Bit + of Mask/Enable register. Default value is Normal (0 which maps to + active-low open collector). The other value is Inverted + (1 which maps to active-high open collector). Specify this property to set + the alert polarity to active-high. + $ref: /schemas/types.yaml#/definitions/flag + + ti,maximum-expected-current-microamp: + description: | + This value indicates the maximum current in microamps that you can + expect to measure with ina233 in your circuit. + + This value will be used to calculate the Current_LSB and current/power + coefficient for the pmbus and to calibrate the IC. + minimum: 32768 + maximum: 4294967295 + default: 32768000 + required: - compatible - reg allOf: - $ref: hwmon-common.yaml# + - if: + properties: + compatible: + contains: + enum: + - silergy,sq52206 + - silergy,sy24655 + - ti,ina209 + - ti,ina219 + - ti,ina220 + - ti,ina226 + - ti,ina230 + - ti,ina231 + - ti,ina237 + - ti,ina238 + - ti,ina260 + then: + properties: + ti,maximum-expected-current-microamp: false unevaluatedProperties: false @@ -88,5 +131,6 @@ examples: label = "vdd_3v0"; shunt-resistor = <1000>; vs-supply = <&vdd_3v0>; + ti,alert-polarity-active-high; }; }; |