diff options
Diffstat (limited to 'Documentation/devicetree/bindings/iio')
7 files changed, 105 insertions, 13 deletions
diff --git a/Documentation/devicetree/bindings/iio/adc/amlogic,meson-saradc.txt b/Documentation/devicetree/bindings/iio/adc/amlogic,meson-saradc.txt index 047189192aec..f413e82c8b83 100644 --- a/Documentation/devicetree/bindings/iio/adc/amlogic,meson-saradc.txt +++ b/Documentation/devicetree/bindings/iio/adc/amlogic,meson-saradc.txt @@ -2,6 +2,8 @@ Required properties: - compatible: depending on the SoC this should be one of: + - "amlogic,meson8-saradc" for Meson8 + - "amlogic,meson8b-saradc" for Meson8b - "amlogic,meson-gxbb-saradc" for GXBB - "amlogic,meson-gxl-saradc" for GXL - "amlogic,meson-gxm-saradc" for GXM diff --git a/Documentation/devicetree/bindings/iio/adc/renesas,gyroadc.txt b/Documentation/devicetree/bindings/iio/adc/renesas,gyroadc.txt index f5b0adae6010..df5b9f2ad8d8 100644 --- a/Documentation/devicetree/bindings/iio/adc/renesas,gyroadc.txt +++ b/Documentation/devicetree/bindings/iio/adc/renesas,gyroadc.txt @@ -1,4 +1,4 @@ -* Renesas RCar GyroADC device driver +* Renesas R-Car GyroADC device driver The GyroADC block is a reduced SPI block with up to 8 chipselect lines, which supports the SPI protocol of a selected few SPI ADCs. The SPI ADCs @@ -16,8 +16,7 @@ Required properties: - clocks: References to all the clocks specified in the clock-names property as specified in Documentation/devicetree/bindings/clock/clock-bindings.txt. -- clock-names: Shall contain "fck" and "if". The "fck" is the GyroADC block - clock, the "if" is the interface clock. +- clock-names: Shall contain "fck". The "fck" is the GyroADC block clock. - power-domains: Must contain a reference to the PM domain, if available. - #address-cells: Should be <1> (setting for the subnodes) for all ADCs except for "fujitsu,mb88101a". Should be <0> (setting for @@ -75,8 +74,8 @@ Example: adc@e6e54000 { compatible = "renesas,r8a7791-gyroadc", "renesas,rcar-gyroadc"; reg = <0 0xe6e54000 0 64>; - clocks = <&mstp9_clks R8A7791_CLK_GYROADC>, <&clk_65m>; - clock-names = "fck", "if"; + clocks = <&mstp9_clks R8A7791_CLK_GYROADC>; + clock-names = "fck"; power-domains = <&sysc R8A7791_PD_ALWAYS_ON>; pinctrl-0 = <&adc_pins>; diff --git a/Documentation/devicetree/bindings/iio/adc/st,stm32-adc.txt b/Documentation/devicetree/bindings/iio/adc/st,stm32-adc.txt index e35f9f1b3200..8310073f14e1 100644 --- a/Documentation/devicetree/bindings/iio/adc/st,stm32-adc.txt +++ b/Documentation/devicetree/bindings/iio/adc/st,stm32-adc.txt @@ -21,11 +21,19 @@ own configurable sequence and trigger: Contents of a stm32 adc root node: ----------------------------------- Required properties: -- compatible: Should be "st,stm32f4-adc-core". +- compatible: Should be one of: + "st,stm32f4-adc-core" + "st,stm32h7-adc-core" - reg: Offset and length of the ADC block register set. - interrupts: Must contain the interrupt for ADC block. -- clocks: Clock for the analog circuitry (common to all ADCs). -- clock-names: Must be "adc". +- clocks: Core can use up to two clocks, depending on part used: + - "adc" clock: for the analog circuitry, common to all ADCs. + It's required on stm32f4. + It's optional on stm32h7. + - "bus" clock: for registers access, common to all ADCs. + It's not present on stm32f4. + It's required on stm32h7. +- clock-names: Must be "adc" and/or "bus" depending on part used. - interrupt-controller: Identifies the controller node as interrupt-parent - vref-supply: Phandle to the vref input analog reference voltage. - #interrupt-cells = <1>; @@ -42,14 +50,18 @@ An ADC block node should contain at least one subnode, representing an ADC instance available on the machine. Required properties: -- compatible: Should be "st,stm32f4-adc". +- compatible: Should be one of: + "st,stm32f4-adc" + "st,stm32h7-adc" - reg: Offset of ADC instance in ADC block (e.g. may be 0x0, 0x100, 0x200). -- clocks: Input clock private to this ADC instance. +- clocks: Input clock private to this ADC instance. It's required only on + stm32f4, that has per instance clock input for registers access. - interrupt-parent: Phandle to the parent interrupt controller. - interrupts: IRQ Line for the ADC (e.g. may be 0 for adc@0, 1 for adc@100 or 2 for adc@200). - st,adc-channels: List of single-ended channels muxed for this ADC. - It can have up to 16 channels, numbered from 0 to 15 (resp. for in0..in15). + It can have up to 16 channels on stm32f4 or 20 channels on stm32h7, numbered + from 0 to 15 or 19 (resp. for in0..in15 or in0..in19). - #io-channel-cells = <1>: See the IIO bindings section "IIO consumers" in Documentation/devicetree/bindings/iio/iio-bindings.txt @@ -58,7 +70,9 @@ Optional properties: See ../../dma/dma.txt for details. - dma-names: Must be "rx" when dmas property is being used. - assigned-resolution-bits: Resolution (bits) to use for conversions. Must - match device available resolutions (e.g. can be 6, 8, 10 or 12 on stm32f4). + match device available resolutions: + * can be 6, 8, 10 or 12 on stm32f4 + * can be 8, 10, 12, 14 or 16 on stm32h7 Default is maximum resolution if unset. Example: diff --git a/Documentation/devicetree/bindings/iio/adc/ti-adc084s021.txt b/Documentation/devicetree/bindings/iio/adc/ti-adc084s021.txt new file mode 100644 index 000000000000..4259e50620bc --- /dev/null +++ b/Documentation/devicetree/bindings/iio/adc/ti-adc084s021.txt @@ -0,0 +1,19 @@ +* Texas Instruments' ADC084S021 + +Required properties: + - compatible : Must be "ti,adc084s021" + - reg : SPI chip select number for the device + - vref-supply : The regulator supply for ADC reference voltage + - spi-cpol : Per spi-bus bindings + - spi-cpha : Per spi-bus bindings + - spi-max-frequency : Per spi-bus bindings + +Example: +adc@0 { + compatible = "ti,adc084s021"; + reg = <0>; + vref-supply = <&adc_vref>; + spi-cpol; + spi-cpha; + spi-max-frequency = <16000000>; +}; diff --git a/Documentation/devicetree/bindings/iio/adc/ti-adc108s102.txt b/Documentation/devicetree/bindings/iio/adc/ti-adc108s102.txt new file mode 100644 index 000000000000..bbbbb4a9f58f --- /dev/null +++ b/Documentation/devicetree/bindings/iio/adc/ti-adc108s102.txt @@ -0,0 +1,18 @@ +* Texas Instruments' ADC108S102 and ADC128S102 ADC chip + +Required properties: + - compatible: Should be "ti,adc108s102" + - reg: spi chip select number for the device + - vref-supply: The regulator supply for ADC reference voltage + +Recommended properties: + - spi-max-frequency: Definition as per + Documentation/devicetree/bindings/spi/spi-bus.txt + +Example: +adc@0 { + compatible = "ti,adc108s102"; + reg = <0>; + vref-supply = <&vdd_supply>; + spi-max-frequency = <1000000>; +}; diff --git a/Documentation/devicetree/bindings/iio/imu/st_lsm6dsx.txt b/Documentation/devicetree/bindings/iio/imu/st_lsm6dsx.txt index 8305fb05ffda..6f28ff55f3ec 100644 --- a/Documentation/devicetree/bindings/iio/imu/st_lsm6dsx.txt +++ b/Documentation/devicetree/bindings/iio/imu/st_lsm6dsx.txt @@ -13,7 +13,8 @@ Optional properties: "data ready" (valid values: 1 or 2). - interrupt-parent: should be the phandle for the interrupt controller - interrupts: interrupt mapping for IRQ. It should be configured with - flags IRQ_TYPE_LEVEL_HIGH or IRQ_TYPE_EDGE_RISING. + flags IRQ_TYPE_LEVEL_HIGH, IRQ_TYPE_EDGE_RISING, IRQ_TYPE_LEVEL_LOW or + IRQ_TYPE_EDGE_FALLING. Refer to interrupt-controller/interrupts.txt for generic interrupt client node bindings. diff --git a/Documentation/devicetree/bindings/iio/multiplexer/io-channel-mux.txt b/Documentation/devicetree/bindings/iio/multiplexer/io-channel-mux.txt new file mode 100644 index 000000000000..c82794002595 --- /dev/null +++ b/Documentation/devicetree/bindings/iio/multiplexer/io-channel-mux.txt @@ -0,0 +1,39 @@ +I/O channel multiplexer bindings + +If a multiplexer is used to select which hardware signal is fed to +e.g. an ADC channel, these bindings describe that situation. + +Required properties: +- compatible : "io-channel-mux" +- io-channels : Channel node of the parent channel that has multiplexed + input. +- io-channel-names : Should be "parent". +- #address-cells = <1>; +- #size-cells = <0>; +- mux-controls : Mux controller node to use for operating the mux +- channels : List of strings, labeling the mux controller states. + +For each non-empty string in the channels property, an io-channel will +be created. The number of this io-channel is the same as the index into +the list of strings in the channels property, and also matches the mux +controller state. The mux controller state is described in +../mux/mux-controller.txt + +Example: + mux: mux-controller { + compatible = "mux-gpio"; + #mux-control-cells = <0>; + + mux-gpios = <&pioA 0 GPIO_ACTIVE_HIGH>, + <&pioA 1 GPIO_ACTIVE_HIGH>; + }; + + adc-mux { + compatible = "io-channel-mux"; + io-channels = <&adc 0>; + io-channel-names = "parent"; + + mux-controls = <&mux>; + + channels = "sync", "in", "system-regulator"; + }; |