summaryrefslogtreecommitdiff
path: root/Documentation/devicetree/bindings/media/i2c/ov5640.txt
diff options
context:
space:
mode:
Diffstat (limited to 'Documentation/devicetree/bindings/media/i2c/ov5640.txt')
-rw-r--r--Documentation/devicetree/bindings/media/i2c/ov5640.txt46
1 files changed, 44 insertions, 2 deletions
diff --git a/Documentation/devicetree/bindings/media/i2c/ov5640.txt b/Documentation/devicetree/bindings/media/i2c/ov5640.txt
index 540b36c4b1f2..8e36da0d8406 100644
--- a/Documentation/devicetree/bindings/media/i2c/ov5640.txt
+++ b/Documentation/devicetree/bindings/media/i2c/ov5640.txt
@@ -1,4 +1,4 @@
-* Omnivision OV5640 MIPI CSI-2 sensor
+* Omnivision OV5640 MIPI CSI-2 / parallel sensor
Required Properties:
- compatible: should be "ovti,ov5640"
@@ -18,7 +18,25 @@ The device node must contain one 'port' child node for its digital output
video port, in accordance with the video interface bindings defined in
Documentation/devicetree/bindings/media/video-interfaces.txt.
-Example:
+OV5640 can be connected to a MIPI CSI-2 bus or a parallel bus endpoint.
+
+Endpoint node required properties for CSI-2 connection are:
+- remote-endpoint: a phandle to the bus receiver's endpoint node.
+- clock-lanes: should be set to <0> (clock lane on hardware lane 0)
+- data-lanes: should be set to <1> or <1 2> (one or two CSI-2 lanes supported)
+
+Endpoint node required properties for parallel connection are:
+- remote-endpoint: a phandle to the bus receiver's endpoint node.
+- bus-width: shall be set to <8> for 8 bits parallel bus
+ or <10> for 10 bits parallel bus
+- data-shift: shall be set to <2> for 8 bits parallel bus
+ (lines 9:2 are used) or <0> for 10 bits parallel bus
+- hsync-active: active state of the HSYNC signal, 0/1 for LOW/HIGH respectively.
+- vsync-active: active state of the VSYNC signal, 0/1 for LOW/HIGH respectively.
+- pclk-sample: sample data on rising (1) or falling (0) edge of the pixel clock
+ signal.
+
+Examples:
&i2c1 {
ov5640: camera@3c {
@@ -35,6 +53,7 @@ Example:
reset-gpios = <&gpio1 20 GPIO_ACTIVE_LOW>;
port {
+ /* MIPI CSI-2 bus endpoint */
ov5640_to_mipi_csi2: endpoint {
remote-endpoint = <&mipi_csi2_from_ov5640>;
clock-lanes = <0>;
@@ -43,3 +62,26 @@ Example:
};
};
};
+
+&i2c1 {
+ ov5640: camera@3c {
+ compatible = "ovti,ov5640";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_ov5640>;
+ reg = <0x3c>;
+ clocks = <&clk_ext_camera>;
+ clock-names = "xclk";
+
+ port {
+ /* Parallel bus endpoint */
+ ov5640_to_parallel: endpoint {
+ remote-endpoint = <&parallel_from_ov5640>;
+ bus-width = <8>;
+ data-shift = <2>; /* lines 9:2 are used */
+ hsync-active = <0>;
+ vsync-active = <0>;
+ pclk-sample = <1>;
+ };
+ };
+ };
+};