diff options
Diffstat (limited to 'Documentation/devicetree/bindings/media/i2c/st,st-mipid02.yaml')
| -rw-r--r-- | Documentation/devicetree/bindings/media/i2c/st,st-mipid02.yaml | 175 |
1 files changed, 175 insertions, 0 deletions
diff --git a/Documentation/devicetree/bindings/media/i2c/st,st-mipid02.yaml b/Documentation/devicetree/bindings/media/i2c/st,st-mipid02.yaml new file mode 100644 index 000000000000..b68141264c0e --- /dev/null +++ b/Documentation/devicetree/bindings/media/i2c/st,st-mipid02.yaml @@ -0,0 +1,175 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/media/i2c/st,st-mipid02.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: STMicroelectronics MIPID02 CSI-2 to PARALLEL bridge + +maintainers: + - Benjamin Mugnier <benjamin.mugnier@foss.st.com> + - Sylvain Petinot <sylvain.petinot@foss.st.com> + +description: + MIPID02 has two CSI-2 input ports, only one of those ports can be + active at a time. Active port input stream will be de-serialized + and its content outputted through PARALLEL output port. + CSI-2 first input port is a dual lane 800Mbps per lane whereas CSI-2 + second input port is a single lane 800Mbps. Both ports support clock + and data lane polarity swap. First port also supports data lane swap. + PARALLEL output port has a maximum width of 12 bits. + Supported formats are RAW6, RAW7, RAW8, RAW10, RAW12, RGB565, RGB888, + RGB444, YUV420 8-bit, YUV422 8-bit and YUV420 10-bit. + +properties: + compatible: + const: st,st-mipid02 + + reg: + maxItems: 1 + + clocks: + maxItems: 1 + + clock-names: + const: xclk + + VDDE-supply: + description: + Sensor digital IO supply. Must be 1.8 volts. + + VDDIN-supply: + description: + Sensor internal regulator supply. Must be 1.8 volts. + + reset-gpios: + description: + Reference to the GPIO connected to the xsdn pin, if any. + This is an active low signal to the mipid02. + + ports: + $ref: /schemas/graph.yaml#/properties/ports + properties: + port@0: + $ref: /schemas/graph.yaml#/$defs/port-base + unevaluatedProperties: false + description: CSI-2 first input port + properties: + endpoint: + $ref: /schemas/media/video-interfaces.yaml# + unevaluatedProperties: false + + properties: + data-lanes: + description: + Single-lane operation shall be <1> or <2> . + Dual-lane operation shall be <1 2> or <2 1> . + minItems: 1 + maxItems: 2 + + lane-polarities: + description: + Any lane can be inverted or not. + minItems: 1 + maxItems: 2 + + required: + - data-lanes + + port@1: + $ref: /schemas/graph.yaml#/$defs/port-base + unevaluatedProperties: false + description: CSI-2 second input port + properties: + endpoint: + $ref: /schemas/media/video-interfaces.yaml# + unevaluatedProperties: false + + properties: + data-lanes: + description: + Single-lane operation shall be <1> or <2> . + maxItems: 1 + + lane-polarities: + description: + Any lane can be inverted or not. + maxItems: 1 + + required: + - data-lanes + + port@2: + $ref: /schemas/graph.yaml#/$defs/port-base + unevaluatedProperties: false + description: Output port + properties: + endpoint: + $ref: /schemas/media/video-interfaces.yaml# + unevaluatedProperties: false + + properties: + bus-width: + enum: [6, 7, 8, 10, 12] + + required: + - bus-width + + anyOf: + - required: + - port@0 + - required: + - port@1 + + required: + - port@2 + +additionalProperties: false + +required: + - compatible + - reg + - clocks + - clock-names + - VDDE-supply + - VDDIN-supply + - ports + +examples: + - | + i2c { + #address-cells = <1>; + #size-cells = <0>; + mipid02: csi2rx@14 { + compatible = "st,st-mipid02"; + reg = <0x14>; + clocks = <&clk_ext_camera_12>; + clock-names = "xclk"; + VDDE-supply = <&vdd>; + VDDIN-supply = <&vdd>; + ports { + #address-cells = <1>; + #size-cells = <0>; + port@0 { + reg = <0>; + + ep0: endpoint { + data-lanes = <1 2>; + remote-endpoint = <&mipi_csi2_in>; + }; + }; + port@2 { + reg = <2>; + + ep2: endpoint { + bus-width = <8>; + hsync-active = <0>; + vsync-active = <0>; + remote-endpoint = <¶llel_out>; + }; + }; + }; + }; + }; + +... |