diff options
Diffstat (limited to 'Documentation/devicetree/bindings/mmc/mmc-controller.yaml')
| -rw-r--r-- | Documentation/devicetree/bindings/mmc/mmc-controller.yaml | 346 |
1 files changed, 4 insertions, 342 deletions
diff --git a/Documentation/devicetree/bindings/mmc/mmc-controller.yaml b/Documentation/devicetree/bindings/mmc/mmc-controller.yaml index 58ae298cd2fc..9d7a1298c455 100644 --- a/Documentation/devicetree/bindings/mmc/mmc-controller.yaml +++ b/Documentation/devicetree/bindings/mmc/mmc-controller.yaml @@ -9,7 +9,7 @@ title: MMC Controller Common Properties maintainers: - Ulf Hansson <ulf.hansson@linaro.org> -description: | +description: These properties are common to multiple MMC host controllers. Any host that requires the respective functionality should implement them using these definitions. @@ -18,351 +18,13 @@ description: | (and the corresponding mmcblkN devices) by defining an alias in the /aliases device tree node. +$ref: mmc-controller-common.yaml# + properties: $nodename: pattern: "^mmc(@.*)?$" - "#address-cells": - const: 1 - description: | - The cell is the slot ID if a function subnode is used. - - "#size-cells": - const: 0 - - # Card Detection. - # If none of these properties are supplied, the host native card - # detect will be used. Only one of them should be provided. - - broken-cd: - $ref: /schemas/types.yaml#/definitions/flag - description: - There is no card detection available; polling must be used. - - cd-gpios: - maxItems: 1 - description: - The card detection will be done using the GPIO provided. - - non-removable: - $ref: /schemas/types.yaml#/definitions/flag - description: - Non-removable slot (like eMMC); assume always present. - - # *NOTE* on CD and WP polarity. To use common for all SD/MMC host - # controllers line polarity properties, we have to fix the meaning - # of the "normal" and "inverted" line levels. We choose to follow - # the SDHCI standard, which specifies both those lines as "active - # low." Therefore, using the "cd-inverted" property means, that the - # CD line is active high, i.e. it is high, when a card is - # inserted. Similar logic applies to the "wp-inverted" property. - # - # CD and WP lines can be implemented on the hardware in one of two - # ways: as GPIOs, specified in cd-gpios and wp-gpios properties, or - # as dedicated pins. Polarity of dedicated pins can be specified, - # using *-inverted properties. GPIO polarity can also be specified - # using the GPIO_ACTIVE_LOW flag. This creates an ambiguity in the - # latter case. We choose to use the XOR logic for GPIO CD and WP - # lines. This means, the two properties are "superimposed," for - # example leaving the GPIO_ACTIVE_LOW flag clear and specifying the - # respective *-inverted property property results in a - # double-inversion and actually means the "normal" line polarity is - # in effect. - wp-inverted: - $ref: /schemas/types.yaml#/definitions/flag - description: - The Write Protect line polarity is inverted. - - cd-inverted: - $ref: /schemas/types.yaml#/definitions/flag - description: - The CD line polarity is inverted. - - # Other properties - - bus-width: - description: - Number of data lines. - $ref: /schemas/types.yaml#/definitions/uint32 - enum: [1, 4, 8] - default: 1 - - max-frequency: - description: | - Maximum operating frequency of the bus: - - for eMMC, the maximum supported frequency is 200MHz, - - for SD/SDIO cards the SDR104 mode has a max supported - frequency of 208MHz, - - some mmc host controllers do support a max frequency upto - 384MHz. - So, lets keep the maximum supported value here. - - $ref: /schemas/types.yaml#/definitions/uint32 - minimum: 400000 - maximum: 384000000 - - disable-wp: - $ref: /schemas/types.yaml#/definitions/flag - description: - When set, no physical write-protect line is present. This - property should only be specified when the controller has a - dedicated write-protect detection logic. If a GPIO is always used - for the write-protect detection logic, it is sufficient to not - specify the wp-gpios property in the absence of a write-protect - line. Not used in combination with eMMC or SDIO. - - wp-gpios: - maxItems: 1 - description: - GPIO to use for the write-protect detection. - - cd-debounce-delay-ms: - description: - Set delay time before detecting card after card insert - interrupt. - - no-1-8-v: - $ref: /schemas/types.yaml#/definitions/flag - description: - When specified, denotes that 1.8V card voltage is not supported - on this system, even if the controller claims it. - - cap-sd-highspeed: - $ref: /schemas/types.yaml#/definitions/flag - description: - SD high-speed timing is supported. - - cap-mmc-highspeed: - $ref: /schemas/types.yaml#/definitions/flag - description: - MMC high-speed timing is supported. - - sd-uhs-sdr12: - $ref: /schemas/types.yaml#/definitions/flag - description: - SD UHS SDR12 speed is supported. - - sd-uhs-sdr25: - $ref: /schemas/types.yaml#/definitions/flag - description: - SD UHS SDR25 speed is supported. - - sd-uhs-sdr50: - $ref: /schemas/types.yaml#/definitions/flag - description: - SD UHS SDR50 speed is supported. - - sd-uhs-sdr104: - $ref: /schemas/types.yaml#/definitions/flag - description: - SD UHS SDR104 speed is supported. - - sd-uhs-ddr50: - $ref: /schemas/types.yaml#/definitions/flag - description: - SD UHS DDR50 speed is supported. - - cap-power-off-card: - $ref: /schemas/types.yaml#/definitions/flag - description: - Powering off the card is safe. - - cap-mmc-hw-reset: - $ref: /schemas/types.yaml#/definitions/flag - description: - eMMC hardware reset is supported - - cap-sdio-irq: - $ref: /schemas/types.yaml#/definitions/flag - description: - enable SDIO IRQ signalling on this interface - - full-pwr-cycle: - $ref: /schemas/types.yaml#/definitions/flag - description: - Full power cycle of the card is supported. - - full-pwr-cycle-in-suspend: - $ref: /schemas/types.yaml#/definitions/flag - description: - Full power cycle of the card in suspend is supported. - - mmc-ddr-1_2v: - $ref: /schemas/types.yaml#/definitions/flag - description: - eMMC high-speed DDR mode (1.2V I/O) is supported. - - mmc-ddr-1_8v: - $ref: /schemas/types.yaml#/definitions/flag - description: - eMMC high-speed DDR mode (1.8V I/O) is supported. - - mmc-ddr-3_3v: - $ref: /schemas/types.yaml#/definitions/flag - description: - eMMC high-speed DDR mode (3.3V I/O) is supported. - - mmc-hs200-1_2v: - $ref: /schemas/types.yaml#/definitions/flag - description: - eMMC HS200 mode (1.2V I/O) is supported. - - mmc-hs200-1_8v: - $ref: /schemas/types.yaml#/definitions/flag - description: - eMMC HS200 mode (1.8V I/O) is supported. - - mmc-hs400-1_2v: - $ref: /schemas/types.yaml#/definitions/flag - description: - eMMC HS400 mode (1.2V I/O) is supported. - - mmc-hs400-1_8v: - $ref: /schemas/types.yaml#/definitions/flag - description: - eMMC HS400 mode (1.8V I/O) is supported. - - mmc-hs400-enhanced-strobe: - $ref: /schemas/types.yaml#/definitions/flag - description: - eMMC HS400 enhanced strobe mode is supported - - no-mmc-hs400: - $ref: /schemas/types.yaml#/definitions/flag - description: - All eMMC HS400 modes are not supported. - - dsr: - description: - Value the card Driver Stage Register (DSR) should be programmed - with. - $ref: /schemas/types.yaml#/definitions/uint32 - minimum: 0 - maximum: 0xffff - - no-sdio: - $ref: /schemas/types.yaml#/definitions/flag - description: - Controller is limited to send SDIO commands during - initialization. - - no-sd: - $ref: /schemas/types.yaml#/definitions/flag - description: - Controller is limited to send SD commands during initialization. - - no-mmc: - $ref: /schemas/types.yaml#/definitions/flag - description: - Controller is limited to send MMC commands during - initialization. - - fixed-emmc-driver-type: - description: - For non-removable eMMC, enforce this driver type. The value is - the driver type as specified in the eMMC specification (table - 206 in spec version 5.1) - $ref: /schemas/types.yaml#/definitions/uint32 - minimum: 0 - maximum: 4 - - post-power-on-delay-ms: - description: - It was invented for MMC pwrseq-simple which could be referred to - mmc-pwrseq-simple.yaml. But now it\'s reused as a tunable delay - waiting for I/O signalling and card power supply to be stable, - regardless of whether pwrseq-simple is used. Default to 10ms if - no available. - default: 10 - - supports-cqe: - $ref: /schemas/types.yaml#/definitions/flag - description: - The presence of this property indicates that the corresponding - MMC host controller supports HW command queue feature. - - disable-cqe-dcmd: - $ref: /schemas/types.yaml#/definitions/flag - description: - The presence of this property indicates that the MMC - controller\'s command queue engine (CQE) does not support direct - commands (DCMDs). - - keep-power-in-suspend: - $ref: /schemas/types.yaml#/definitions/flag - description: - SDIO only. Preserves card power during a suspend/resume cycle. - - wakeup-source: - $ref: /schemas/types.yaml#/definitions/flag - description: - SDIO only. Enables wake up of host system on SDIO IRQ assertion. - - vmmc-supply: - description: - Supply for the card power - - vqmmc-supply: - description: - Supply for the bus IO line power, such as a level shifter. - If the level shifter is controlled by a GPIO line, this shall - be modeled as a "regulator-fixed" with a GPIO line for - switching the level shifter on/off. - - mmc-pwrseq: - $ref: /schemas/types.yaml#/definitions/phandle - description: - System-on-Chip designs may specify a specific MMC power - sequence. To successfully detect an (e)MMC/SD/SDIO card, that - power sequence must be maintained while initializing the card. - -patternProperties: - "^.*@[0-9]+$": - type: object - description: | - On embedded systems the cards connected to a host may need - additional properties. These can be specified in subnodes to the - host controller node. The subnodes are identified by the - standard \'reg\' property. Which information exactly can be - specified depends on the bindings for the SDIO function driver - for the subnode, as specified by the compatible string. - - properties: - compatible: - description: | - Name of SDIO function following generic names recommended - practice - - reg: - items: - - minimum: 0 - maximum: 7 - description: - Must contain the SDIO function number of the function this - subnode describes. A value of 0 denotes the memory SD - function, values from 1 to 7 denote the SDIO functions. - - required: - - reg - - "^clk-phase-(legacy|sd-hs|mmc-(hs|hs[24]00|ddr52)|uhs-(sdr(12|25|50|104)|ddr50))$": - $ref: /schemas/types.yaml#/definitions/uint32-array - - minItems: 2 - maxItems: 2 - items: - minimum: 0 - maximum: 359 - description: - Set the clock (phase) delays which are to be configured in the - controller while switching to particular speed mode. These values - are in pair of degrees. - -dependencies: - cd-debounce-delay-ms: [ cd-gpios ] - fixed-emmc-driver-type: [ non-removable ] - -additionalProperties: true +unevaluatedProperties: true examples: - | |