1 files changed, 0 insertions, 159 deletions
diff --git a/Documentation/devicetree/bindings/net/broadcom-bluetooth.yaml b/Documentation/devicetree/bindings/net/broadcom-bluetooth.yaml
deleted file mode 100644
index cc70b00c6ce5..000000000000
--- a/Documentation/devicetree/bindings/net/broadcom-bluetooth.yaml
+++ /dev/null
@@ -1,159 +0,0 @@
-# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause)
-%YAML 1.2
----
-$id: http://devicetree.org/schemas/net/broadcom-bluetooth.yaml#
-$schema: http://devicetree.org/meta-schemas/core.yaml#
-
-title: Broadcom Bluetooth Chips
-
-maintainers:
-  - Linus Walleij <linus.walleij@linaro.org>
-
-description:
-  This binding describes Broadcom UART-attached bluetooth chips.
-
-properties:
-  compatible:
-    enum:
-      - brcm,bcm20702a1
-      - brcm,bcm4329-bt
-      - brcm,bcm4330-bt
-      - brcm,bcm4334-bt
-      - brcm,bcm43430a0-bt
-      - brcm,bcm43430a1-bt
-      - brcm,bcm43438-bt
-      - brcm,bcm4345c5
-      - brcm,bcm43540-bt
-      - brcm,bcm4335a0
-      - brcm,bcm4349-bt
-      - cypress,cyw4373a0-bt
-      - infineon,cyw55572-bt
-
-  shutdown-gpios:
-    maxItems: 1
-    description: GPIO specifier for the line BT_REG_ON used to
-      power on the BT module
-
-  reset-gpios:
-    maxItems: 1
-    description: GPIO specifier for the line BT_RST_N used to
-      reset the BT module. This should be marked as
-      GPIO_ACTIVE_LOW.
-
-  device-wakeup-gpios:
-    maxItems: 1
-    description: GPIO specifier for the line BT_WAKE used to
-      wakeup the controller. This is using the BT_GPIO_0
-      pin on the chip when in use.
-
-  host-wakeup-gpios:
-    maxItems: 1
-    deprecated: true
-    description: GPIO specifier for the line HOST_WAKE used
-      to wakeup the host processor. This is using he BT_GPIO_1
-      pin on the chip when in use. This is deprecated and replaced
-      by interrupts and "host-wakeup" interrupt-names
-
-  clocks:
-    minItems: 1
-    maxItems: 2
-    description: 1 or 2 clocks as defined in clock-names below,
-      in that order
-
-  clock-names:
-    description: Names of the 1 to 2 supplied clocks
-    oneOf:
-      - const: extclk
-        deprecated: true
-        description: Deprecated in favor of txco
-
-      - const: txco
-        description: >
-          external reference clock (not a standalone crystal)
-
-      - const: lpo
-        description: >
-          external low power 32.768 kHz clock
-
-      - items:
-          - const: txco
-          - const: lpo
-
-  vbat-supply:
-    description: phandle to regulator supply for VBAT
-
-  vddio-supply:
-    description: phandle to regulator supply for VDDIO
-
-  brcm,bt-pcm-int-params:
-    $ref: /schemas/types.yaml#/definitions/uint8-array
-    minItems: 5
-    maxItems: 5
-    description: |-
-      configure PCM parameters via a 5-byte array:
-       sco-routing: 0 = PCM, 1 = Transport, 2 = Codec, 3 = I2S
-       pcm-interface-rate: 128KBps, 256KBps, 512KBps, 1024KBps, 2048KBps
-       pcm-frame-type: short, long
-       pcm-sync-mode: slave, master
-       pcm-clock-mode: slave, master
-
-  brcm,requires-autobaud-mode:
-    type: boolean
-    description:
-      Set this property if autobaud mode is required. Autobaud mode is required
-      if the device's initial baud rate in normal mode is not supported by the
-      host or if the device requires autobaud mode startup before loading FW.
-
-  interrupts:
-    items:
-      - description: Handle to the line HOST_WAKE used to wake
-          up the host processor. This uses the BT_GPIO_1 pin on
-          the chip when in use.
-
-  interrupt-names:
-    items:
-      - const: host-wakeup
-
-  max-speed: true
-  current-speed: true
-
-required:
-  - compatible
-
-dependencies:
-  brcm,requires-autobaud-mode: [ shutdown-gpios ]
-
-if:
-  not:
-    properties:
-      compatible:
-        contains:
-          enum:
-            - brcm,bcm20702a1
-            - brcm,bcm4329-bt
-            - brcm,bcm4330-bt
-then:
-  properties:
-    reset-gpios: false
-
-additionalProperties: false
-
-examples:
-  - |
-    #include <dt-bindings/gpio/gpio.h>
-    #include <dt-bindings/interrupt-controller/irq.h>
-
-    uart {
-        uart-has-rtscts;
-
-        bluetooth {
-            compatible = "brcm,bcm4330-bt";
-            max-speed = <921600>;
-            brcm,bt-pcm-int-params = [01 02 00 01 01];
-            shutdown-gpios = <&gpio 30 GPIO_ACTIVE_HIGH>;
-            device-wakeup-gpios = <&gpio 7 GPIO_ACTIVE_HIGH>;
-            reset-gpios = <&gpio 9 GPIO_ACTIVE_LOW>;
-            interrupt-parent = <&gpio>;
-            interrupts = <8 IRQ_TYPE_EDGE_FALLING>;
-        };
-    };