diff options
Diffstat (limited to 'Documentation/devicetree/bindings/net/ti,dp83822.yaml')
-rw-r--r-- | Documentation/devicetree/bindings/net/ti,dp83822.yaml | 116 |
1 files changed, 116 insertions, 0 deletions
diff --git a/Documentation/devicetree/bindings/net/ti,dp83822.yaml b/Documentation/devicetree/bindings/net/ti,dp83822.yaml new file mode 100644 index 000000000000..784866ea392b --- /dev/null +++ b/Documentation/devicetree/bindings/net/ti,dp83822.yaml @@ -0,0 +1,116 @@ +# SPDX-License-Identifier: (GPL-2.0+ OR BSD-2-Clause) +# Copyright (C) 2020 Texas Instruments Incorporated +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/net/ti,dp83822.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: TI DP83822 ethernet PHY + +maintainers: + - Andrew Davis <afd@ti.com> + +description: | + The DP83822 is a low-power, single-port, 10/100 Mbps Ethernet PHY. It + provides all of the physical layer functions needed to transmit and receive + data over standard, twisted-pair cables or to connect to an external, + fiber-optic transceiver. Additionally, the DP83822 provides flexibility to + connect to a MAC through a standard MII, RMII, or RGMII interface + + Specifications about the Ethernet PHY can be found at: + http://www.ti.com/lit/ds/symlink/dp83822i.pdf + +allOf: + - $ref: ethernet-phy.yaml# + +properties: + reg: + maxItems: 1 + + ti,link-loss-low: + type: boolean + description: | + DP83822 PHY in Fiber mode only. + Sets the DP83822 to detect a link drop condition when the signal goes + high. If not set then link drop will occur when the signal goes low. + This property is only applicable if the fiber mode support is strapped + to on. + + ti,fiber-mode: + type: boolean + description: | + DP83822 PHY only. + If present the DP83822 PHY is configured to operate in fiber mode + Fiber mode support can also be strapped. If the strap pin is not set + correctly or not set at all then this boolean can be used to enable it. + If the fiber mode is not strapped then signal detection for the PHY + is disabled. + In fiber mode, auto-negotiation is disabled and the PHY can only work in + 100base-fx (full and half duplex) modes. + + rx-internal-delay-ps: + description: | + DP83822 PHY only. + Setting this property to a non-zero number sets the RX internal delay + for the PHY. The internal delay for the PHY is fixed to 3.5ns relative + to receive data. + + tx-internal-delay-ps: + description: | + DP83822 PHY only. + Setting this property to a non-zero number sets the TX internal delay + for the PHY. The internal delay for the PHY is fixed to 3.5ns relative + to transmit data. + + ti,cfg-dac-minus-one-bp: + description: | + DP83826 PHY only. + Sets the voltage ratio (with respect to the nominal value) + of the logical level -1 for the MLT-3 encoded TX data. + enum: [5000, 5625, 6250, 6875, 7500, 8125, 8750, 9375, 10000, + 10625, 11250, 11875, 12500, 13125, 13750, 14375, 15000] + default: 10000 + + ti,cfg-dac-plus-one-bp: + description: | + DP83826 PHY only. + Sets the voltage ratio (with respect to the nominal value) + of the logical level +1 for the MLT-3 encoded TX data. + enum: [5000, 5625, 6250, 6875, 7500, 8125, 8750, 9375, 10000, + 10625, 11250, 11875, 12500, 13125, 13750, 14375, 15000] + default: 10000 + + ti,rmii-mode: + description: | + If present, select the RMII operation mode. Two modes are + available: + - RMII master, where the PHY outputs a 50MHz reference clock which can + be connected to the MAC. + - RMII slave, where the PHY expects a 50MHz reference clock input + shared with the MAC. + The RMII operation mode can also be configured by its straps. + If the strap pin is not set correctly or not set at all, then this can be + used to configure it. + $ref: /schemas/types.yaml#/definitions/string + enum: + - master + - slave + +required: + - reg + +unevaluatedProperties: false + +examples: + - | + mdio0 { + #address-cells = <1>; + #size-cells = <0>; + ethphy0: ethernet-phy@0 { + reg = <0>; + rx-internal-delay-ps = <1>; + tx-internal-delay-ps = <1>; + }; + }; + +... |