diff options
Diffstat (limited to 'Documentation/devicetree/bindings/net')
4 files changed, 4 insertions, 7 deletions
diff --git a/Documentation/devicetree/bindings/net/hisilicon-hns-nic.txt b/Documentation/devicetree/bindings/net/hisilicon-hns-nic.txt index b9ff4ba6454e..f0421ee3c714 100644 --- a/Documentation/devicetree/bindings/net/hisilicon-hns-nic.txt +++ b/Documentation/devicetree/bindings/net/hisilicon-hns-nic.txt @@ -8,7 +8,7 @@ Required properties: specifies a reference to the associating hardware driver node. see Documentation/devicetree/bindings/net/hisilicon-hns-dsaf.txt - port-id: is the index of port provided by DSAF (the accelerator). DSAF can - connect to 8 PHYs. Port 0 to 1 are both used for adminstration purpose. They + connect to 8 PHYs. Port 0 to 1 are both used for administration purpose. They are called debug ports. The remaining 6 PHYs are taken according to the mode of DSAF. diff --git a/Documentation/devicetree/bindings/net/phy.txt b/Documentation/devicetree/bindings/net/phy.txt index c00a9a894547..bc1c3c8bf8fa 100644 --- a/Documentation/devicetree/bindings/net/phy.txt +++ b/Documentation/devicetree/bindings/net/phy.txt @@ -35,8 +35,6 @@ Optional Properties: - broken-turn-around: If set, indicates the PHY device does not correctly release the turn around line low at the end of a MDIO transaction. -- reset-gpios: Reference to a GPIO used to reset the phy. - Example: ethernet-phy@0 { @@ -44,5 +42,4 @@ ethernet-phy@0 { interrupt-parent = <40000>; interrupts = <35 1>; reg = <0>; - reset-gpios = <&gpio1 17 GPIO_ACTIVE_LOW>; }; diff --git a/Documentation/devicetree/bindings/net/stmmac.txt b/Documentation/devicetree/bindings/net/stmmac.txt index 4d302db657c0..95816c5fc589 100644 --- a/Documentation/devicetree/bindings/net/stmmac.txt +++ b/Documentation/devicetree/bindings/net/stmmac.txt @@ -51,8 +51,8 @@ Optional properties: AXI register inside the DMA module: - snps,lpi_en: enable Low Power Interface - snps,xit_frm: unlock on WoL - - snps,wr_osr_lmt: max write oustanding req. limit - - snps,rd_osr_lmt: max read oustanding req. limit + - snps,wr_osr_lmt: max write outstanding req. limit + - snps,rd_osr_lmt: max read outstanding req. limit - snps,kbbe: do not cross 1KiB boundary. - snps,axi_all: align address - snps,blen: this is a vector of supported burst length. diff --git a/Documentation/devicetree/bindings/net/ti,dp83867.txt b/Documentation/devicetree/bindings/net/ti,dp83867.txt index 58d935b58598..5d21141a68b5 100644 --- a/Documentation/devicetree/bindings/net/ti,dp83867.txt +++ b/Documentation/devicetree/bindings/net/ti,dp83867.txt @@ -2,7 +2,7 @@ Required properties: - reg - The ID number for the phy, usually a small integer - - ti,rx-internal-delay - RGMII Recieve Clock Delay - see dt-bindings/net/ti-dp83867.h + - ti,rx-internal-delay - RGMII Receive Clock Delay - see dt-bindings/net/ti-dp83867.h for applicable values - ti,tx-internal-delay - RGMII Transmit Clock Delay - see dt-bindings/net/ti-dp83867.h for applicable values |