diff options
Diffstat (limited to 'Documentation/devicetree/bindings/net')
4 files changed, 74 insertions, 10 deletions
diff --git a/Documentation/devicetree/bindings/net/davinci_emac.txt b/Documentation/devicetree/bindings/net/davinci_emac.txt index 24c5cdaba8d2..ca83dcc84fb8 100644 --- a/Documentation/devicetree/bindings/net/davinci_emac.txt +++ b/Documentation/devicetree/bindings/net/davinci_emac.txt @@ -20,6 +20,8 @@ Required properties: Optional properties: - phy-handle: See ethernet.txt file in the same directory. If absent, davinci_emac driver defaults to 100/FULL. +- nvmem-cells: phandle, reference to an nvmem node for the MAC address +- nvmem-cell-names: string, should be "mac-address" if nvmem is to be used - ti,davinci-rmii-en: 1 byte, 1 means use RMII - ti,davinci-no-bd-ram: boolean, does EMAC have BD RAM? diff --git a/Documentation/devicetree/bindings/net/dsa/qca8k.txt b/Documentation/devicetree/bindings/net/dsa/qca8k.txt index bbcb255c3150..93a7469e70d4 100644 --- a/Documentation/devicetree/bindings/net/dsa/qca8k.txt +++ b/Documentation/devicetree/bindings/net/dsa/qca8k.txt @@ -12,10 +12,15 @@ Required properties: Subnodes: The integrated switch subnode should be specified according to the binding -described in dsa/dsa.txt. As the QCA8K switches do not have a N:N mapping of -port and PHY id, each subnode describing a port needs to have a valid phandle -referencing the internal PHY connected to it. The CPU port of this switch is -always port 0. +described in dsa/dsa.txt. If the QCA8K switch is connect to a SoC's external +mdio-bus each subnode describing a port needs to have a valid phandle +referencing the internal PHY it is connected to. This is because there's no +N:N mapping of port and PHY id. + +Don't use mixed external and internal mdio-bus configurations, as this is +not supported by the hardware. + +The CPU port of this switch is always port 0. A CPU port node has the following optional node: @@ -31,8 +36,9 @@ For QCA8K the 'fixed-link' sub-node supports only the following properties: - 'full-duplex' (boolean, optional), to indicate that full duplex is used. When absent, half duplex is assumed. -Example: +Examples: +for the external mdio-bus configuration: &mdio0 { phy_port1: phy@0 { @@ -55,12 +61,12 @@ Example: reg = <4>; }; - switch0@0 { + switch@10 { compatible = "qca,qca8337"; #address-cells = <1>; #size-cells = <0>; - reg = <0>; + reg = <0x10>; ports { #address-cells = <1>; @@ -108,3 +114,56 @@ Example: }; }; }; + +for the internal master mdio-bus configuration: + + &mdio0 { + switch@10 { + compatible = "qca,qca8337"; + #address-cells = <1>; + #size-cells = <0>; + + reg = <0x10>; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + label = "cpu"; + ethernet = <&gmac1>; + phy-mode = "rgmii"; + fixed-link { + speed = 1000; + full-duplex; + }; + }; + + port@1 { + reg = <1>; + label = "lan1"; + }; + + port@2 { + reg = <2>; + label = "lan2"; + }; + + port@3 { + reg = <3>; + label = "lan3"; + }; + + port@4 { + reg = <4>; + label = "lan4"; + }; + + port@5 { + reg = <5>; + label = "wan"; + }; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/net/ethernet.txt b/Documentation/devicetree/bindings/net/ethernet.txt index cfc376bc977a..a68621580584 100644 --- a/Documentation/devicetree/bindings/net/ethernet.txt +++ b/Documentation/devicetree/bindings/net/ethernet.txt @@ -10,15 +10,14 @@ Documentation/devicetree/bindings/phy/phy-bindings.txt. the boot program; should be used in cases where the MAC address assigned to the device by the boot program is different from the "local-mac-address" property; -- nvmem-cells: phandle, reference to an nvmem node for the MAC address; -- nvmem-cell-names: string, should be "mac-address" if nvmem is to be used; - max-speed: number, specifies maximum speed in Mbit/s supported by the device; - max-frame-size: number, maximum transfer unit (IEEE defined MTU), rather than the maximum frame size (there's contradiction in the Devicetree Specification). - phy-mode: string, operation mode of the PHY interface. This is now a de-facto standard property; supported values are: - * "internal" + * "internal" (Internal means there is not a standard bus between the MAC and + the PHY, something proprietary is being used to embed the PHY in the MAC.) * "mii" * "gmii" * "sgmii" diff --git a/Documentation/devicetree/bindings/net/macb.txt b/Documentation/devicetree/bindings/net/macb.txt index 174f292d8a3e..8b80515729d7 100644 --- a/Documentation/devicetree/bindings/net/macb.txt +++ b/Documentation/devicetree/bindings/net/macb.txt @@ -26,6 +26,10 @@ Required properties: Optional elements: 'tsu_clk' - clocks: Phandles to input clocks. +Optional properties: +- nvmem-cells: phandle, reference to an nvmem node for the MAC address +- nvmem-cell-names: string, should be "mac-address" if nvmem is to be used + Optional properties for PHY child node: - reset-gpios : Should specify the gpio for phy reset - magic-packet : If present, indicates that the hardware supports waking |