1 files changed, 0 insertions, 135 deletions
diff --git a/Documentation/devicetree/bindings/pci/rockchip-pcie-host.txt b/Documentation/devicetree/bindings/pci/rockchip-pcie-host.txt
deleted file mode 100644
index af34c65773fd..000000000000
--- a/Documentation/devicetree/bindings/pci/rockchip-pcie-host.txt
+++ /dev/null
@@ -1,135 +0,0 @@
-* Rockchip AXI PCIe Root Port Bridge DT description
-
-Required properties:
-- #address-cells: Address representation for root ports, set to <3>
-- #size-cells: Size representation for root ports, set to <2>
-- #interrupt-cells: specifies the number of cells needed to encode an
-		interrupt source. The value must be 1.
-- compatible: Should contain "rockchip,rk3399-pcie"
-- reg: Two register ranges as listed in the reg-names property
-- reg-names: Must include the following names
-	- "axi-base"
-	- "apb-base"
-- clocks: Must contain an entry for each entry in clock-names.
-		See ../clocks/clock-bindings.txt for details.
-- clock-names: Must include the following entries:
-	- "aclk"
-	- "aclk-perf"
-	- "hclk"
-	- "pm"
-- msi-map: Maps a Requester ID to an MSI controller and associated
-	msi-specifier data. See ./pci-msi.txt
-- interrupts: Three interrupt entries must be specified.
-- interrupt-names: Must include the following names
-	- "sys"
-	- "legacy"
-	- "client"
-- resets: Must contain seven entries for each entry in reset-names.
-	   See ../reset/reset.txt for details.
-- reset-names: Must include the following names
-	- "core"
-	- "mgmt"
-	- "mgmt-sticky"
-	- "pipe"
-	- "pm"
-	- "aclk"
-	- "pclk"
-- pinctrl-names : The pin control state names
-- pinctrl-0: The "default" pinctrl state
-- #interrupt-cells: specifies the number of cells needed to encode an
-	interrupt source. The value must be 1.
-- interrupt-map-mask and interrupt-map: standard PCI properties
-
-Required properties for legacy PHY model (deprecated):
-- phys: From PHY bindings: Phandle for the Generic PHY for PCIe.
-- phy-names:  MUST be "pcie-phy".
-
-Required properties for per-lane PHY model (preferred):
-- phys: Must contain an phandle to a PHY for each entry in phy-names.
-- phy-names: Must include 4 entries for all 4 lanes even if some of
-  them won't be used for your cases. Entries are of the form "pcie-phy-N":
-  where N ranges from 0 to 3.
-  (see example below and you MUST also refer to ../phy/rockchip-pcie-phy.txt
-  for changing the #phy-cells of phy node to support it)
-
-Optional Property:
-- aspm-no-l0s: RC won't support ASPM L0s. This property is needed if
-	using 24MHz OSC for RC's PHY.
-- ep-gpios: contain the entry for pre-reset GPIO
-- num-lanes: number of lanes to use
-- vpcie12v-supply: The phandle to the 12v regulator to use for PCIe.
-- vpcie3v3-supply: The phandle to the 3.3v regulator to use for PCIe.
-- vpcie1v8-supply: The phandle to the 1.8v regulator to use for PCIe.
-- vpcie0v9-supply: The phandle to the 0.9v regulator to use for PCIe.
-
-*Interrupt controller child node*
-The core controller provides a single interrupt for legacy INTx. The PCIe node
-should contain an interrupt controller node as a target for the PCI
-'interrupt-map' property. This node represents the domain at which the four
-INTx interrupts are decoded and routed.
-
-
-Required properties for Interrupt controller child node:
-- interrupt-controller: identifies the node as an interrupt controller
-- #address-cells: specifies the number of cells needed to encode an
-	address. The value must be 0.
-- #interrupt-cells: specifies the number of cells needed to encode an
-	interrupt source. The value must be 1.
-
-Example:
-
-pcie0: pcie@f8000000 {
-	compatible = "rockchip,rk3399-pcie";
-	#address-cells = <3>;
-	#size-cells = <2>;
-	clocks = <&cru ACLK_PCIE>, <&cru ACLK_PERF_PCIE>,
-		 <&cru PCLK_PCIE>, <&cru SCLK_PCIE_PM>;
-	clock-names = "aclk", "aclk-perf",
-		      "hclk", "pm";
-	bus-range = <0x0 0x1>;
-	interrupts = <GIC_SPI 49 IRQ_TYPE_LEVEL_HIGH 0>,
-		     <GIC_SPI 50 IRQ_TYPE_LEVEL_HIGH 0>,
-		     <GIC_SPI 51 IRQ_TYPE_LEVEL_HIGH 0>;
-	interrupt-names = "sys", "legacy", "client";
-	assigned-clocks = <&cru SCLK_PCIEPHY_REF>;
-	assigned-clock-parents = <&cru SCLK_PCIEPHY_REF100M>;
-	assigned-clock-rates = <100000000>;
-	ep-gpios = <&gpio3 13 GPIO_ACTIVE_HIGH>;
-	ranges = <0x83000000 0x0 0xfa000000 0x0 0xfa000000 0x0 0x600000
-		  0x81000000 0x0 0xfa600000 0x0 0xfa600000 0x0 0x100000>;
-	num-lanes = <4>;
-	msi-map = <0x0 &its 0x0 0x1000>;
-	reg = <0x0 0xf8000000 0x0 0x2000000>, <0x0 0xfd000000 0x0 0x1000000>;
-	reg-names = "axi-base", "apb-base";
-	resets = <&cru SRST_PCIE_CORE>, <&cru SRST_PCIE_MGMT>,
-		 <&cru SRST_PCIE_MGMT_STICKY>, <&cru SRST_PCIE_PIPE> ,
-		 <&cru SRST_PCIE_PM>, <&cru SRST_P_PCIE>, <&cru SRST_A_PCIE>;
-	reset-names = "core", "mgmt", "mgmt-sticky", "pipe",
-		      "pm", "pclk", "aclk";
-	/* deprecated legacy PHY model */
-	phys = <&pcie_phy>;
-	phy-names = "pcie-phy";
-	pinctrl-names = "default";
-	pinctrl-0 = <&pcie_clkreq>;
-	#interrupt-cells = <1>;
-	interrupt-map-mask = <0 0 0 7>;
-	interrupt-map = <0 0 0 1 &pcie0_intc 0>,
-			<0 0 0 2 &pcie0_intc 1>,
-			<0 0 0 3 &pcie0_intc 2>,
-			<0 0 0 4 &pcie0_intc 3>;
-	pcie0_intc: interrupt-controller {
-		interrupt-controller;
-		#address-cells = <0>;
-		#interrupt-cells = <1>;
-	};
-};
-
-pcie0: pcie@f8000000 {
-	...
-
-	/* preferred per-lane PHY model */
-	phys = <&pcie_phy 0>, <&pcie_phy 1>, <&pcie_phy 2>, <&pcie_phy 3>;
-	phy-names = "pcie-phy-0", "pcie-phy-1", "pcie-phy-2", "pcie-phy-3";
-
-	...
-};