summaryrefslogtreecommitdiff
path: root/Documentation/devicetree/bindings/pci/rockchip-pcie.txt
diff options
context:
space:
mode:
Diffstat (limited to 'Documentation/devicetree/bindings/pci/rockchip-pcie.txt')
-rw-r--r--Documentation/devicetree/bindings/pci/rockchip-pcie.txt28
1 files changed, 25 insertions, 3 deletions
diff --git a/Documentation/devicetree/bindings/pci/rockchip-pcie.txt b/Documentation/devicetree/bindings/pci/rockchip-pcie.txt
index 1453a734c2f5..af34c65773fd 100644
--- a/Documentation/devicetree/bindings/pci/rockchip-pcie.txt
+++ b/Documentation/devicetree/bindings/pci/rockchip-pcie.txt
@@ -19,8 +19,6 @@ Required properties:
- "pm"
- msi-map: Maps a Requester ID to an MSI controller and associated
msi-specifier data. See ./pci-msi.txt
-- phys: From PHY bindings: Phandle for the Generic PHY for PCIe.
-- phy-names: MUST be "pcie-phy".
- interrupts: Three interrupt entries must be specified.
- interrupt-names: Must include the following names
- "sys"
@@ -42,11 +40,24 @@ Required properties:
interrupt source. The value must be 1.
- interrupt-map-mask and interrupt-map: standard PCI properties
+Required properties for legacy PHY model (deprecated):
+- phys: From PHY bindings: Phandle for the Generic PHY for PCIe.
+- phy-names: MUST be "pcie-phy".
+
+Required properties for per-lane PHY model (preferred):
+- phys: Must contain an phandle to a PHY for each entry in phy-names.
+- phy-names: Must include 4 entries for all 4 lanes even if some of
+ them won't be used for your cases. Entries are of the form "pcie-phy-N":
+ where N ranges from 0 to 3.
+ (see example below and you MUST also refer to ../phy/rockchip-pcie-phy.txt
+ for changing the #phy-cells of phy node to support it)
+
Optional Property:
- aspm-no-l0s: RC won't support ASPM L0s. This property is needed if
using 24MHz OSC for RC's PHY.
-- ep-gpios: contain the entry for pre-reset gpio
+- ep-gpios: contain the entry for pre-reset GPIO
- num-lanes: number of lanes to use
+- vpcie12v-supply: The phandle to the 12v regulator to use for PCIe.
- vpcie3v3-supply: The phandle to the 3.3v regulator to use for PCIe.
- vpcie1v8-supply: The phandle to the 1.8v regulator to use for PCIe.
- vpcie0v9-supply: The phandle to the 0.9v regulator to use for PCIe.
@@ -95,6 +106,7 @@ pcie0: pcie@f8000000 {
<&cru SRST_PCIE_PM>, <&cru SRST_P_PCIE>, <&cru SRST_A_PCIE>;
reset-names = "core", "mgmt", "mgmt-sticky", "pipe",
"pm", "pclk", "aclk";
+ /* deprecated legacy PHY model */
phys = <&pcie_phy>;
phy-names = "pcie-phy";
pinctrl-names = "default";
@@ -111,3 +123,13 @@ pcie0: pcie@f8000000 {
#interrupt-cells = <1>;
};
};
+
+pcie0: pcie@f8000000 {
+ ...
+
+ /* preferred per-lane PHY model */
+ phys = <&pcie_phy 0>, <&pcie_phy 1>, <&pcie_phy 2>, <&pcie_phy 3>;
+ phy-names = "pcie-phy-0", "pcie-phy-1", "pcie-phy-2", "pcie-phy-3";
+
+ ...
+};