diff options
Diffstat (limited to 'Documentation/devicetree/bindings/remoteproc')
3 files changed, 134 insertions, 63 deletions
diff --git a/Documentation/devicetree/bindings/remoteproc/qcom,q6v5.txt b/Documentation/devicetree/bindings/remoteproc/qcom,q6v5.txt index 41ca5df5be5a..c416746f93cf 100644 --- a/Documentation/devicetree/bindings/remoteproc/qcom,q6v5.txt +++ b/Documentation/devicetree/bindings/remoteproc/qcom,q6v5.txt @@ -12,6 +12,7 @@ on the Qualcomm Hexagon core. "qcom,msm8916-mss-pil", "qcom,msm8974-mss-pil" "qcom,msm8996-mss-pil" + "qcom,msm8998-mss-pil" "qcom,sdm845-mss-pil" - reg: @@ -41,6 +42,7 @@ on the Qualcomm Hexagon core. qcom,msm8974-mss-pil: must be "wdog", "fatal", "ready", "handover", "stop-ack" qcom,msm8996-mss-pil: + qcom,msm8998-mss-pil: qcom,sdm845-mss-pil: must be "wdog", "fatal", "ready", "handover", "stop-ack", "shutdown-ack" @@ -70,6 +72,9 @@ on the Qualcomm Hexagon core. qcom,msm8996-mss-pil: must be "iface", "bus", "mem", "xo", "gpll0_mss", "snoc_axi", "mnoc_axi", "pnoc", "qdss" + qcom,msm8998-mss-pil: + must be "iface", "bus", "mem", "xo", "gpll0_mss", + "snoc_axi", "mnoc_axi", "qdss" qcom,sdm845-mss-pil: must be "iface", "bus", "mem", "xo", "gpll0_mss", "snoc_axi", "mnoc_axi", "prng" @@ -137,6 +142,7 @@ For the compatible string below the following supplies are required: qcom,msm8974-mss-pil: no power-domain names required qcom,msm8996-mss-pil: + qcom,msm8998-mss-pil: must be "cx", "mx" qcom,sdm845-mss-pil: must be "cx", "mx", "mss", "load_state" diff --git a/Documentation/devicetree/bindings/remoteproc/st,stm32-rproc.yaml b/Documentation/devicetree/bindings/remoteproc/st,stm32-rproc.yaml new file mode 100644 index 000000000000..acf18d170352 --- /dev/null +++ b/Documentation/devicetree/bindings/remoteproc/st,stm32-rproc.yaml @@ -0,0 +1,128 @@ +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause) +%YAML 1.2 +--- +$id: "http://devicetree.org/schemas/remoteproc/st,stm32-rproc.yaml#" +$schema: "http://devicetree.org/meta-schemas/core.yaml#" + +title: STMicroelectronics STM32 remote processor controller bindings + +description: + This document defines the binding for the remoteproc component that loads and + boots firmwares on the ST32MP family chipset. + +maintainers: + - Fabien Dessenne <fabien.dessenne@st.com> + - Arnaud Pouliquen <arnaud.pouliquen@st.com> + +properties: + compatible: + const: st,stm32mp1-m4 + + reg: + description: + Address ranges of the RETRAM and MCU SRAM memories used by the remote + processor. + maxItems: 3 + + resets: + maxItems: 1 + + st,syscfg-holdboot: + allOf: + - $ref: "/schemas/types.yaml#/definitions/phandle-array" + description: remote processor reset hold boot + - Phandle of syscon block. + - The offset of the hold boot setting register. + - The field mask of the hold boot. + maxItems: 1 + + st,syscfg-tz: + allOf: + - $ref: "/schemas/types.yaml#/definitions/phandle-array" + description: + Reference to the system configuration which holds the RCC trust zone mode + - Phandle of syscon block. + - The offset of the RCC trust zone mode register. + - The field mask of the RCC trust zone mode. + maxItems: 1 + + interrupts: + description: Should contain the WWDG1 watchdog reset interrupt + maxItems: 1 + + mboxes: + description: + This property is required only if the rpmsg/virtio functionality is used. + items: + - description: | + A channel (a) used to communicate through virtqueues with the + remote proc. + Bi-directional channel: + - from local to remote = send message + - from remote to local = send message ack + - description: | + A channel (b) working the opposite direction of channel (a) + - description: | + A channel (c) used by the local proc to notify the remote proc that it + is about to be shut down. + Unidirectional channel: + - from local to remote, where ACK from the remote means that it is + ready for shutdown + minItems: 1 + maxItems: 3 + + mbox-names: + items: + - const: vq0 + - const: vq1 + - const: shutdown + minItems: 1 + maxItems: 3 + + memory-region: + description: + List of phandles to the reserved memory regions associated with the + remoteproc device. This is variable and describes the memories shared with + the remote processor (e.g. remoteproc firmware and carveouts, rpmsg + vrings, ...). + (see ../reserved-memory/reserved-memory.txt) + + st,syscfg-pdds: + allOf: + - $ref: "/schemas/types.yaml#/definitions/phandle-array" + description: | + Reference to the system configuration which holds the remote + 1st cell: phandle to syscon block + 2nd cell: register offset containing the deep sleep setting + 3rd cell: register bitmask for the deep sleep bit + maxItems: 1 + + st,auto-boot: + $ref: /schemas/types.yaml#/definitions/flag + description: + If defined, when remoteproc is probed, it loads the default firmware and + starts the remote processor. + +required: + - compatible + - reg + - resets + - st,syscfg-holdboot + - st,syscfg-tz + +additionalProperties: false + +examples: + - | + #include <dt-bindings/reset/stm32mp1-resets.h> + m4_rproc: m4@10000000 { + compatible = "st,stm32mp1-m4"; + reg = <0x10000000 0x40000>, + <0x30000000 0x40000>, + <0x38000000 0x10000>; + resets = <&rcc MCU_R>; + st,syscfg-holdboot = <&rcc 0x10C 0x1>; + st,syscfg-tz = <&rcc 0x000 0x1>; + }; + +... diff --git a/Documentation/devicetree/bindings/remoteproc/stm32-rproc.txt b/Documentation/devicetree/bindings/remoteproc/stm32-rproc.txt deleted file mode 100644 index 5fa915a4b736..000000000000 --- a/Documentation/devicetree/bindings/remoteproc/stm32-rproc.txt +++ /dev/null @@ -1,63 +0,0 @@ -STMicroelectronics STM32 Remoteproc ------------------------------------ -This document defines the binding for the remoteproc component that loads and -boots firmwares on the ST32MP family chipset. - -Required properties: -- compatible: Must be "st,stm32mp1-m4" -- reg: Address ranges of the RETRAM and MCU SRAM memories used by the - remote processor. -- resets: Reference to a reset controller asserting the remote processor. -- st,syscfg-holdboot: Reference to the system configuration which holds the - remote processor reset hold boot - 1st cell: phandle of syscon block - 2nd cell: register offset containing the hold boot setting - 3rd cell: register bitmask for the hold boot field -- st,syscfg-tz: Reference to the system configuration which holds the RCC trust - zone mode - 1st cell: phandle to syscon block - 2nd cell: register offset containing the RCC trust zone mode setting - 3rd cell: register bitmask for the RCC trust zone mode bit - -Optional properties: -- interrupts: Should contain the watchdog interrupt -- mboxes: This property is required only if the rpmsg/virtio functionality - is used. List of phandle and mailbox channel specifiers: - - a channel (a) used to communicate through virtqueues with the - remote proc. - Bi-directional channel: - - from local to remote = send message - - from remote to local = send message ack - - a channel (b) working the opposite direction of channel (a) - - a channel (c) used by the local proc to notify the remote proc - that it is about to be shut down. - Unidirectional channel: - - from local to remote, where ACK from the remote means - that it is ready for shutdown -- mbox-names: This property is required if the mboxes property is used. - - must be "vq0" for channel (a) - - must be "vq1" for channel (b) - - must be "shutdown" for channel (c) -- memory-region: List of phandles to the reserved memory regions associated with - the remoteproc device. This is variable and describes the - memories shared with the remote processor (eg: remoteproc - firmware and carveouts, rpmsg vrings, ...). - (see ../reserved-memory/reserved-memory.txt) -- st,syscfg-pdds: Reference to the system configuration which holds the remote - processor deep sleep setting - 1st cell: phandle to syscon block - 2nd cell: register offset containing the deep sleep setting - 3rd cell: register bitmask for the deep sleep bit -- st,auto-boot: If defined, when remoteproc is probed, it loads the default - firmware and starts the remote processor. - -Example: - m4_rproc: m4@10000000 { - compatible = "st,stm32mp1-m4"; - reg = <0x10000000 0x40000>, - <0x30000000 0x40000>, - <0x38000000 0x10000>; - resets = <&rcc MCU_R>; - st,syscfg-holdboot = <&rcc 0x10C 0x1>; - st,syscfg-tz = <&rcc 0x000 0x1>; - }; |